SX25i
25W Integrated Amplifier
Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
This page has intentionally been left blank.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
i
Introducing the
Perreaux Silhouette Series
Designed as a range of high quality, yet affordable modules; the
‘Silhouette’ series will compliment and enhance your existing
system.
Drawing on our extensive knowledge gained from more than a
quarter of a century of developing highest quality audio products,
the ‘Silhouette’ concentrates our legendary design and build
quality into a compact package without sacrificing performance.
The Perreaux ‘Silhouette’ series provides performance levels
never before seen in its class.
Key Features ꢀ Class A signal stages
ꢀ
Highest quality internal power supply featuring a custom
designed, fully shielded toroidal transformer and 13200µF
of smoothing capacitance
ꢀ
ꢀ
Optimal internal layout incorporating total separation
between channels
Enhanced audio design featuring highest quality PCB and
minimal internal wiring
ꢀ
ꢀ
ꢀ
ꢀ
Line-out connections
High current drive
Compact
Stylish
T he P erreaux “S ilhouette” series takes you even closer to the
elusive goal of “T he P erfect R e-C reation of a M usical
E vent”.
From all of us at Perreaux Industries Limited, thank you for
choosing the Perreaux Silhouette Series SX25i Integrated
Amplifier.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
Important Safety Instructions
Note:
Please read all instructions carefully before attempting to
operate your Perreaux “Silhouette” SX25i Integrated
Amplifier.
ALWAYS switch off power to your system before attempting to
connect or disconnect cables.
ALWAYS disconnect your system from the mains before
attempting to clean your unit.
ALWAYS keep electrical equipment out of reach of children.
ALWAYS unplug sensitive electronic equipment during
electrical storms.
NEVER disconnect the mains earth from the system.
NEVER operate the SX25i with the cover removed.
NEVER use any liquid inside the SX25i.
NEVER bypass any fuse.
NEVER attempt to repair the SX25i. In the event of a problem,
please contact your Perreaux dealer.
NEVER expose the SX25i to extremely high or low
temperatures.
NEVER operate this product in an explosive atmosphere.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
Table of Contents
i
Introducing the Perreaux Silhouette Series .................................... 3
Important Safety Instructions............................................................. 4
Table of Contents .................................................................................. 5
Unpacking and Placement .................................................................. 6
Instant Install .......................................................................................... 7
Front Panel Functions .......................................................................... 9
Rear Panel Functions ..........................................................................10
Special Design Philosophies..............................................................12
Special Design Features .....................................................................14
Care and Maintenance .......................................................................16
Warranty Information ........................................................................17
Extended Warranty Registration Form..........................................18
Troubleshooting Guide......................................................................19
Specifications........................................................................................21
Physical Dimensions............................................................................24
Contact Details.....................................................................................25
ii
iii
1
2
3
4
5
6
7
8
9
10
11
12
13
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Unpacking and Placement
Unpacking The SX25i is packaged for maximum protection. To open, sit the
Procedure box upright and cut the reinforced tape at the top of the box. The
product can now be removed.
Pull the foam protecting end-caps off either side of the unit and
remove the black material covering.
The SX25i Integrated amplifier is now unpacked and ready for
further installation.
Note:
Please retain all packaging material for future transport.
Box 1 x SX25i Integrated amplifier
Contents 1 x Product manual
3 x Performance analysis charts
1 x Detachable AC power cord
Placing Your The SX25i should generally be placed close to your source
SX25i equipment, thus keeping interconnect cabling between the SX25i
and associated components as short as practical. This will reduce
the systems susceptibility to radio frequency interference and the
negative effects associated with long cables.
Ventilation The SX25i is a convection cooled amplifier. For optimal
Requirements performance, the unit MUST receive adequate ventilation.
ꢀ
ꢀ
Please do not cover the product with a cloth or similar.
Please do not mount the SX25i directly onto carpeted
surfaces.
In the event that the SX25i is to be incorporated into custom
cabinetry, please refer to the dimensional information provided in
the Physical Dimensions section of the manual (Chapter 12).
Note:
Please take all necessary steps to ensure that the unit
receives adequate ventilation
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Instant Install
If you are like us, the first thing you will want to do is to play
your favourite piece of music through your new SX25i. The
following instructions are written to enable you to achieve this as
quickly as possible. These are not comprehensive instructions,
but are designed to enable you to play music now!
Note:
Please take the time to read the SX25i manual thoroughly
as it incorporates many features, which will enhance its
operation.
Placement
The SX25i is a convection cooled amplifier and best results will
be achieved when placed on a solid surface with adequate
ventilation. DO NOT place on a carpeted floor or cover the
amplifier!
Place the SX25i close or near the source component in order to
make as short a connection as possible.
Turn off associated components
This minimises the potential to damage any other components
when connecting your SX25i into the system.
Connect source to SX25i
Connect the audio output from the source component to the
inputs at the rear of the SX25i. Refer to Chapter 4 for Rear Panel
information.
Connect loud speaker cables to SX25i
Connect your left and right channel loudspeaker leads to the
bindng posts at the rear of the amplifier. Refer to Chapter 4 for
Rear Panel information.
Note:
Make sure the nominal impedance of the loudspeakers is
not lower than 2Ω.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch on SX25i
Caution!
Prior to connecting the AC mains, please check the voltage
label on the rear panel to ensure that your unit conforms to
the power supply in your area. Never attempt to connect
the unit to the incorrect voltage.
Insert the power cord supplied into the rear of the SX25i and into
the wall. Switch on the socket at the wall and turn on the power
of the SX25i by setting the power switch down.
Switch on source component
Power up your source component and start your favourite
recording. Slowly increase the SX25i volume to achieve a
comfortable listening level.
CONGRATULATIONS!
Now that you have achieved your first objective, sit back, relax
and please read the rest of the manual at your own pace in your
favourite armchair whilst sipping a hot cup of coffee. You’ll find
the whole experience much more pleasurable whilst listening to
music.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Front Panel Functions
Power LED
This blue LED indicates the power status of your SX25i
integrated amplifier.
Volume Control
The high-quality, machined aluminium knob is the sole user
interface, reminding the user at every touch of the superior build
quality designed into the SX25i. Volume control motion is
smooth and accurate, providing absolute control with near
infinite gain resolution.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Rear Panel Functions
Right and Left Speaker Binding Posts
Binding posts are clearly marked and colour coded RED Positive
(+) and BLACK Negative (-). This polarity must be observed
when connecting loudspeakers, i.e. positive terminal of the
SX25i to the positive terminal of the loudspeaker and negative
terminal of the SX25i to the negative terminal of the
loudspeaker.
Caution!
Never connect the amplifier’s output terminals to any
device other than a loudspeaker.
Please do not short circuit the amplifier’s output terminals.
Never connect the output of one amplifier to the output
terminals of another amplifier.
Do not over-tighten the binding posts on your amplifier.
Right and Left Line Inputs
Input from source component, accepts a standard unbalanced
input (RCA). The left channel connection is on the right when
looking from the rear, indicated by white inner ring. For more
information on input specifications, please refer to Chapter 11.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial Number/Voltage Label
The serial number is unique to your SX25i. Please record this
number and store it in a safe place. For any service related
enquiry, please be prepared to quote the product serial number to
Perreaux personnel or their service representative.
The voltage displayed in this area is the ONLY voltage that can
be accepted by the unit.
Caution!
Never attempt to connect the unit to the incorrect voltage.
On/Off Switch
When operating the switch down, power is applied to the SX25i.
AC Mains Input
An IEC-standard mains input is provided at the rear of the unit.
The AC cord set is removable, allowing it to be upgraded at your
will.
Right and Left Line Outputs
Line level output, accepts a standard unbalanced input (RCA).
The left channel connection is on the right when looking from
the rear, indicated by white inner ring. For more information on
input specifications, please refer to Chapter 11.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Special Design Philosophies
Perreaux has been designing and manufacturing only the highest
quality audio componentry for more than a quarter of a century.
Technology has continued to evolve rapidly over that time and
our knowledge and application of design, materials and
manufacturing techniques has advanced in tandem with this.
Today’s Perreaux range comes closer to fulfilling our shared
vision than at any other time in the past.
The SX25i has been developed to meet customer demands for
compact higher quality products. Careful attention has been
taken throughout the development phase, not to make
compromises that would degrade the high quality of reproduction
that the unit is capable of delivering.
To follow is a discussion on some of Perreaux design
philosophies that have been incorporated into the entire range.
Minimalist Leading British architect, John Pawson, writes:
Design
“The Minimum can be defined as the perfection
that an object achieves when it is no longer
possible to improve it by subtraction. This is the
quality that an object has when every component,
every detail, and every junction has been reduced
or condensed to the essentials. It is the result of
the omission of the inessentials”.
Perreaux has historically embraced the minimalist ethic from an
audio design perspective only. The concept of “less equating to
more” has been at the heart of all Perreaux audio designs for
more than a quarter of a century. Our current product offering
takes the minimalist ethic to new levels by totally embracing the
concept.
Minimalist Electronics
We wish to maximise the quality of your listening pleasure by
keeping the componentry and signal path as uncluttered, short
and clean possible. All components in the signal path, even those
of the highest quality have an effect on the signal, thereby
altering the quality of the reproduction in some way. Our aim is
to recreate in its entirety, the original performance by not adding
or subtracting anything, irrespective of the source.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimalist Aesthetics
Our products appeal to those who seek the ultimate in audio
exclusivity, namely the perfect blend of “form and function”.
“Form and function” are both tough masters. We make no
excuses for producing some of the most distinctive high-end
audio products on the planet. We let “form and function” blend
together in perfect harmony. This surely is the essence of true
minimalist utilisation.
Minimalism in a Wider Context
John Pawson writes:
“Clearly simplicity has dimensions to it that go
beyond the purely aesthetic: it can be seen as the
reflection of some innate, inner quality, or the
pursuit of philosophical or literary insight into the
nature of harmony, reason, and truth”.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Special Design Features
Construction The SX25i is stylish and unobtrusive. The front panel is made
from high quality solid 6.0mm (0.2”) thick aluminium extrusion
featuring our trademark machined Perreaux logo and large
volume control knob. These are finished in durable and stylish
satin chrome finish electroplate. On/off status is provided via a
discreet blue LED inset into the front panel. The chassis and
cover are both manufactured from heavy gauge steel. No cover
fixing screws are visible. These minimalist styling cues combine
seamlessly to allow form and function to blend in harmony and
are typical hallmarks of the Perreaux brand.
Circuit
Topology
Compact At 216mm (8.5”) wide x 58mm (2.3”) high x 190mm (7.5”) deep
the SX25i is extremely compact.
Integrated By eliminating the interface between separate pre and power
amplifiers and removing concerns about impedance matching,
the SX25i provides a shorter, purer signal path without costly
exposed interconnect cables and separate power cords.
Unsurpassed
Performance
Capable of continuously delivering 25w per channel into an 8Ω
load and 35W into 4Ω, the SX25i is powerful. When correctly
matched to loudspeakers, the SX25i will deliver unsurpassed
performance in its class and will effortlessly drive a vast array of
smaller loudspeakers with the control and authority that people
have come to expect from Perreaux products.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Finest The SX25i features a 98VA toroidally wound mains transformer
Quality directly soldered to the PCB, Wima / Elna brand capacitors,
Components highest quality Zobel network, customized internal heat sink
Used
solution and mains and channel fusing. The PCB is double-sided
Throughout and constructed from the highest quality fibreglass base stock
featuring 2oz tracks.
The Power Perreaux has specially developed a fully shielded 98VA internal
Supply toroidal based power supply. No fewer than six filter capacitors
are coupled in parallel providing a total of 13,200uF of power
supply smoothing, keeping ripple to a minimum. As a result the
power supply is extremely rigid, capable of delivering
instantaneous power requirements demanded by musical
transients.
The result is significantly improved dynamic
capabilities.
Simple Front panel features on/off LED indication and volume control
control knob. The rear panel comprises a mains input receptacle,
functionality allowing the cord set to be upgraded if desired, mains switch,
high quality speaker binding posts, RCA line input and line
output.
Single
Channel
Block
Diagram
Ultra Short Careful attention has been paid to the signal path within the
Signal path amplifier. It is ultra short, guarded by ground planes where
necessary and carefully routed to avoid contamination from
power supply and high current bearing sections.
Input Stage Utilising a stable current source, along with accurate current
mirroring circuitry, the input stage of the SX25i, in combination
with the overall circuit topology, provides precise detail
resolution and definitive sonic transparency.
PCB Layout Special attention has been lavished on the PCB layout. The unit
is symmetrical in design with each channel being isolated from
the other. The super clean custom designed power supply is
physically segregated from the rest of the sensitive electronics.
Signal Special attention has been paid to ground planes to maintain
Ground sonic purity. All signal grounding is optimised to provide a
platform for a black background and increased dynamic range.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Care and Maintenance
Note:
Please switch the unit off and remove the cord set from the
rear of the Amplifier before attempting to clean your SX25i
in the manner described below.
Never apply liquid directly to the SX25i.
Never use abrasives.
Never rub in a circular motion.
Cover
The cover features a durable high quality powder coat finish. To
remove finger marks and dirt, lightly rub the surface with a soft
cloth.
If the dirt is not removed, dip your cloth in a mild solution of
soap and water, squeeze excess moisture from it and then gently
reapply to the surface.
Stubborn dirt may be removed by the application of a small
quantity of isopropyl alcohol, applied directly to the cleaning
cloth only, and reworking the effected area.
Front Panel The SX25i front panel features a high quality electroplate finish.
Over time the surface may retain finger marks and may need to
be cleaned to restore it to original condition.
Regular Cleaning
Gently wipe the front panel with a very clean cotton cloth. Wipe
across the surface and never in a circular motion.
Removing Stubborn Marks
Only attempt this infrequently, as too regular or vigorous
application may damage the surface.
Apply a small quantity of any car polish containing carnauba
wax to a very clean cotton cloth.
Note:
The car polish must state “Safe for Clear Coats” as the polish
will therefore contain the absolute minimum amount of
abrasive compound.
Gently wipe over the front panel in lateral motion, allow to dry
then gently wipe off with a very clean cotton cloth.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Warranty Information
1 Year The Perreaux SX25i is warranted free from defects in material
Limited and workmanship under normal use for a period of 1-year (365
Warranty days) from the date of purchase.
To extend the warranty of the Perreaux SX25i to three (3) years
from date of purchase, please return a fully completed warranty
registration form along with a copy of the original receipt of
purchase to:
Perreaux Industries Ltd
PO Box 47413
Ponsonby
Auckland
New Zealand
For the Extended Warranty Registration Form, please refer to
Chapter 9.
3 Year The extended warranty for the Perreaux SX25i is three (3) years
Extended from the date of purchase. If during the warranty period the
Warranty SX25i exhibits defects in materials and/or workmanship, it will
be repaired or replaced, at our option, without charge for either
parts or labour, at our factory in Auckland, New Zealand. The
warranty does not apply to any unit that has been misused,
abused or altered.
Any unit that is not performing satisfactorily may be returned to
the factory in Auckland, New Zealand for evaluation. Return
authorisation must first be obtained by either calling or writing to
Perreaux prior to shipping the unit. Perreaux Industries Ltd and
it’s authorised distributors and dealers shall not be held liable for
any freight or insurance charges. Freight and insurance charges
to and from the Perreaux factory will be the sole responsibility of
the owner of the unit.
There is no other express warranty on the SX25i. Neither this
warranty nor any other warranty, express or implied, including
any implied warranties of merchantability of fitness, shall extend
beyond the warranty period. No responsibility is assumed for
any incidental or consequential damages.
Obtaining In the event that you are experiencing difficulty with your SX25i,
Service please as a first step consult the troubleshooting guide in Chapter
10. For further assistance, please contact your Perreaux dealer.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Extended Warranty
Registration Form
Please complete this form and either fax, mail or e-mail it, along
with a copy of the original receipt, to Perreaux Industries Ltd.
Fax:
+64 9 815 5981
Mail:
Perreaux Industries Ltd
PO Box 47 413
Ponsonby
Auckland
New Zealand
E-mail: [email protected]
Alternatively, complete the online Warranty Registration Form
ꢀ
3 Year Extended
Warranty Form
Name:
Address:
Suburb:
City:
Country:
Telephone:
E-mail:
Website:
Product:
S I L H O U E T T E S X 2 5 i
Serial No:
Dealer:
Purchase Date:
/
/
d
d
m m
y
y
y
y
18
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Troubleshooting Guide
Please use this guide if you are experiencing any problems with
the SX25i in your system. It will provide possible solutions for
some given symptoms.
There is no SX25i not turned on
output from
my system
Make sure the SX25i power switch is in the DOWN position.
AC cord not plugged in
Check that the AC cord is plugged into the IEC socket on the rear
of the SX25i.
Mains power not turned on
Check if the power is turn on at the mains socket on the wall.
Interconnect cables not connected
Make sure that the input and output interconnect cables are
plugged in and are connected to the respective RCA sockets on
the rear of the SX25i.
Source not turned on
Check that your source component is plugged in to the mains and
the power is turned on.
Source not set to play
Ensure that your source component is playing the recording you
would like to listen to, and that pause is not pressed.
No volume setting
Make sure that the volume on your SX25i is set to a suitable
level.
SX25i set to incorrect input
Confirm that the input on your SX25i is connected to the
appropriate source output.
Loud speakers not connected
Check that your loud speakers are firmly connected via cables
into the binding posts on the rear of the SX25i.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
I can hear a Input sockets and/or output binding posts corroded
hum coming
through my
Check that the input and output RCA sockets and binding posts
on the rear of the SX25i are free from corrosion.
loud
speakers
Interconnect cables damaged
Make sure that the integrity of your interconnect cables is sound
and they are firmly connected to your source and the SX25i.
SX25i is close to external interference
Check the proximity of your SX25i to any possible source of
EMI and/or RF interference, for example computers, televisions,
amplifiers, speakers, etc. Ideally the SX25i should be placed as
close as possible to your source.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Specifications
The correlation between published specifications and sonic
quality can be unreliable. A list of numbers reveals virtually
nothing.
All technical measurements must be subject to
qualitative as well as quantitative interpretation. Measurements
of the SX25i reveal excellent results by any standards. Tested at
115V and 230V after a 10 minute warm up period.
Specifications
in Brief
Rated Power Output (per channel)...........................25WRMS into 8Ω
...........................................................................35WRMS into 4Ω
Voltage Swing...................................................................55.2Vp-p
Input Sensitivity..............................................................0.63VRMS
Maximum Gain .................................................................. 27.1dB
Input Impedance:
Typically.............................................................................40kΩ
Total Harmonic Distortion (THD+N):
Typically............................................. 0.002%, @ 1kHz into 8Ω
20Hz to 20kHz................................................................ <0.02%
Frequency Response:
20Hz–20kHz........................................................ +0dB, -0.25dB
5Hz–60kHz............................................................ +0dB, -1.0dB
Signal to Noise Ratio:
Rated Output (unweighted)................................................... 100dB
Dynamic Headroom (rated with music)................................... >2.0dB
Power Consumption:
Idle....................................................................................... 10W
Maximum (at 35W per channel into 4Ω)...................................... 80W
Audio Connections
Inputs.......................................................... 1 pair line level (RCA)
Outputs....................................................... 1 pair line level (RCA)
.......................................................2 pairs speaker binding posts
Other Connections
IEC AC mains input receptacle
Mains Input Voltage
115V or 230V AC at 50Hz/60Hz
(Set within the SX25i at time of manufacture)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Internal Mains Fuse Rating
1 x 2SB 500mA slow blow
(NOT user serviceable)
Internal Output Fuse Rating
2 x 2SB 4A normal blow
(NOT user serviceable)
Overall Dimensions
Width........................................................................216mm (8.5”)
Depth........................................................................192mm (7.6”)
Height.........................................................................58mm (2.3”)
Weight
Gross ..........................................................................3.0kg (6.6lb)
Net............................................................................. 2.4kg (5.3lb)
Specifications
Explained
Rated Power Output (per channel).......................25WRMS into 8Ω
This is the optimum operating level of the unit, offering the best
performance whilst allowing
a
large enough buffer to
accommodate the unpredictable nature of music. It is the
reference output level to which other specifications, such as
sensitivity and gain, are referred. The Rated Output does not
indicate the full capability of the SX25i.
Voltage Swing ...................................................................... 55.2Vp-p
Loud transients call for a sudden burst of power from the
amplifier to drive the speakers. This force is voltage. Peak-to-
peak voltage is a more useful specification than Watts when it
comes to delivering power to a speaker.
Input Sensitivity ...................................................................0.63VRMS
The Input Sensitivity figure indicates the input voltage required
to achieve “rated” output (25WRMS into 8Ω).
Maximum Gain....................................................................... 27.1dB
The amount of amplification the amplifier is asserting on the
input signal. Gain can be calculated by dividing the rated output
by the input sensitivity.
Input Impedance....................................................................... 40kΩ
The resistance “load” that is presented to the source component
that is driving the SX25i.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
THD+N.....................................................0.002%, @ 1kHZ into 8Ω
Total Harmonic Distortion + Noise is the percentage of output
signal which is made up of frequencies added due to harmonics
of the fundamental frequency and noise. By using low-noise
input circuitry and Class A signal stages, Perreaux engineers
have kept this figure to a minimum.
Frequency Response.................. 20Hz to 20kHz, +0dB -0.25dB
Describes the frequency range where the amplitude or strength of
the output signal deviates by no more than 0.25dB.
Signal to Noise Ratio (unweighted)........................................ 100dB
The ratio of desired signal to noise signals in the output.
Integrated reproduction is susceptible to noise because of the
nature of the environment to reveal every detail. This is why
Perreaux engineers have designed the SX25i to maintain a low
noise floor.
Dynamic Headroom ............................................................. >2.0dB
This indicates the SX25i can provide more than enough extra
power to cope with the sharpest musical transients. Without
adequate headroom, an amplifier can become unstable under
clipping conditions. Perreaux amplifiers are intrinsically stable
under all dynamic conditions.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Physical Dimensions
24
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Contact Details
For more information please contact your Perreaux dealer, or
contact:
Perreaux Industries Ltd
PO Box 47 413
Ponsonby
Auckland
New Zealand
Ph:
Fax:
+64 9 815 5452
+64 9 815 5981
E-mail: [email protected]
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Notes
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|