Pelco Security Camera C3412M D User Manual

INSTALLATION/OPERATION

Spectra IV and

Spectra IV SE Series

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SW1: Receiver Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SW2 Switch 1: AD-32 Preset System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SW2 Switch 2: CM9502 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SW2 Switch 3: Control System Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

SW2 Switches 4–5: Serial Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

SW2 Switches 6–8: Baud Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Dome Drive Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

How to Operate Your Dome System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Quick Programming Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Accessing Main Menu (Preset 95) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

CM6700/CM6800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

KBD200A/KBD300A (Direct Mode Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

CM9500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

CM9740/CM9760/CM9770/CM9780 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

KBD4000/KBD4002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

MPT9500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

NET300/NET350/NET4001A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Endura Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

VCD5000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

16X LowLight Color Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

18X LowLight Day/Night Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

22X EXview LowLight Color Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

23X LowLight Day/Night Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

35X LowLight Day/Night Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

DIP Switch Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Display Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Label Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Dome Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Type of Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Auto Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Zoom Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Zoom Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Low Light Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

IR Cut Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Advanced Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Shutter Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

AGC Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Auto Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Auto White Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Backlight Compensation (BLC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Video Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

SENSOR SCAN MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

FIELD ALIGN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Electronic Image Stabilization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Image Enhancement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

LOW LUX NOISE REDUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Wide Dynamic Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Motion Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Auto Flip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Proportional Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Park Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Scan Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Preset Freeze Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Limit Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Azimuth Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Power Up Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Line Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Enable Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Edit Detection Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Activate Aux Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Aux Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Edit Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Window Blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Edit Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Clear Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Blank All Above/Blank All Below . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Aux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Edit Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Title Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Ack Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Activate Aux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Current Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Reset Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Event Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Event Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Edit Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Clear Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

List Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Holiday . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Edit Holiday . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Clear Holiday . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

List Holidays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Scheduled Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Reset, Cycle Power, Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Reset Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Cycle Camera Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Reboot System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Software/Language File Upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

16X Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

18X Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

22X Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

23X Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

35X Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Welcome

Thank you for purchasing Pelco’s premier integrated dome system, Spectra^®IV/Spectra IV SE. Your new system features a high

resolution camera/optics package with programmable dome drive software.

This manual is designed primarily to be a reference tool for the installation and operation of your system. Inside you will find

information about features and commands, as well as a detailed menu tree and a quick start guide. Installation on page 7 provides

information required to set up and install the dome drive. Please thoroughly familiarize yourself with the information in this manual

before installing and using your system.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

This manual contains installation instructions only for the Spectra IV/Spectra IV SE dome drive. For complete installation

instructions for a Spectra IV/Spectra IV SE dome system, refer to the installation manual shipped with the back box.

SWITCH SETTINGS

Before installing the dome drive, configure the receiver address, termination, and baud setting. The DIP switches used to

configure these settings are located on the base of the dome drive.

Figure 1 shows the default settings for the DIP switches. Switch SW1-1 (SW1, switch 1) is set to the ON position; all other

switches are set to the OFF position.

Refer to the following sections to set the address, termination, and baud settings for the dome drive.

O N

SW2

O N

SW1

Figure 1. Default Switch Settings

SW1: RECEIVER ADDRESS

Set the SW1 switches for the address of the dome drive. The following information is required to set the dome drive

address:

P-type control: The default address is 2. Refer to Table A on page 10 for address settings that use P-type control. The

maximum number of receivers is 32.

D-type control: The default address is 1. Refer to Table B on page 11 for address settings that use D-type control. The

maximum number of receivers is 254.

SW2 SWITCH 1: AD-32 PRESET SYSTEM

SW2-1 should be set to the ON position if an AD-32 controller and Pelco’s TXB-AD translator board are used to control the

dome system.

SW2 SWITCH 2: CM9502 SETTING

If a CM9502 matrix system is used with the dome drive, set SW2-2 to the ON position.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

SW2 SWITCH 3: CONTROL SYSTEM COMPATIBILITY

Coaxial Control Systems

Although Spectra IV/Spectra IV SE dome systems can operate with coaxial control systems from many manufacturers, the

system is designed for optimal performance with Pelco Coaxitron^®control products within the length specified for coaxial

cable.

To compensate for coaxial control systems from other manufacturers, Pelco has provided DIP switch SW2-3. Setting

SW2-3 to the ON position may improve dome control with these control systems.

If you are using a Pelco Coaxitron controller, leave SW2-3 in the default OFF position.

Notes:

•

This coaxial control system compatibility feature is only available for dome drive revisions A4 and later (revisions A0

and later for Spectra IV Horizon dome drives). The revision number can be found on the barcode label on the top of

the dome drive. Software version 1.090 and later indicates this mode is available by placing an asterisk next to the

switch number in the Dip Switch Information menu.

•

In some configurations, Pelco CM9502 Series matrix systems use nonstandard Coaxitron commands for functions like

pattern playback. If you experience problems with these functions, set SW2-3 to the ON position.

Pelco P Protocol Control Systems

To compensate for Pelco P protocol control systems from other manufacturers, set SW2-3 to the ON position. This may

improve dome control with some of these control systems.

SW2 SWITCHES 4–5: SERIAL PORT SETTINGS

RS-422 Setting (Default)

SW2-4 and SW2-5 should both be set to the OFF position for RS-422 setting.

For control, only two wires should be connected to the RX- and RX+ connectors on the circuit board inside the back box. For

bidirectional control, four wires should be connected to the RX-, RX+, TX-, and TX+ connectors on the circuit board inside

the back box.

RS-485, 4-Wire Setting

SW2-4 should be set to OFF and SW2-5 should be set to ON if a 4-wire serial port connection is used with RS-485.

Note: This setting is most commonly used with Pelco Endura^®systems.

RS-485, 2-Wire Setting

SW2-4 and SW2-5 should both be set to the ON position if a 2-wire serial port connection is used with RS-485.

This setting is used to allow the Spectra dome system to transmit and receive commands on the same pair of wires. Only

two wires should be connected to the RX- and RX+ connectors on the circuit board inside the back box.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

SW2 SWITCHES 6–8: BAUD SETTINGS

Pelco’s D-type controllers are set for 2400 baud. The default setting for the dome drive is 2400 baud. If you are using a

Pelco D-type controller, do not reset SW2 switches 1–3 or SW2 switches 6–8.

P-type controllers can operate at 2400, 4800, and 9600 baud. Set the SW2 switches (6, 7, and 8), located on the base of

the dome drive, to the same baud as the P-type controller.

Switch Number

SW2-6

Off

SW2-7

Off

SW2-8

Off

2400 Baud (default for D-type control)

4800 Baud (default for P-type control)

9600 Baud

Off

SW2 Switch 9: Coaxial/UTP Cable

SW2-9 should be set to the OFF position (default) if you are using coaxial cable. If you are using unsheilded twisted pair

(UTP) cable, set SW2-9 to the ON position.

SW2 Switch 10: Termination Setting

When connecting more than one Spectra IV/Spectra IV SE dome system to a single controller, terminate the unit farthest

from the controller. Termination is only required for the last dome in the series.

The dome drive is shipped from the factory in the unterminated (OFF) position. To terminate the dome drive, set SW2-10 to

the ON position.

Note: Dome termination is not required for Coaxitron^®control.

DOME DRIVE INSTALLATION

Install the dome drive. Align the blue and red tabs with the blue and red arrows on the hinged door inside the back box.

Push the tabs in. Insert one side and then the other side. Continue pushing on the ends of the tabs until both sides click

into place (refer to Figure 2). To use your dome system, refer to Getting Started on page 19.

Figure 2. Dome Drive Installation

Note: When removing a dome drive that has been in use, caution should be taken to avoid direct contact with the top

plate of the unit. This section of the unit will be warm to the touch when first removed from an operating unit.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table A. Switch Settings for SW1 P-Type Control

SWITCH SETTING

SPECTRA

ADDRESS

SW1-1

OFF

SW1-2

OFF

SW1-3

OFF

SW1-4

OFF

SW1-5

OFF

SW1-6

OFF

SW1-7

OFF

SW1-8

OFF

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. Switch Settings for SW1 D-Type Control

SWITCH SETTING

SPECTRA

ADDRESS

SW1-1

SW1-2

OFF

SW1-3

OFF

SW1-4

OFF

SW1-5

OFF

SW1-6

OFF

SW1-7

OFF

SW1-8

OFF

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. Switch Settings for SW1 D-Type Control (Continued)

SWITCH SETTING

SPECTRA

ADDRESS

SW1-1

OFF

SW1-2

OFF

SW1-3

SW1-4

OFF

SW1-5

OFF

SW1-6

OFF

SW1-7

OFF

SW1-8

OFF

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. Switch Settings for SW1 D-Type Control (Continued)

SWITCH SETTING

SPECTRA

ADDRESS

SW1-1

SW1-2

SW1-3

SW1-4

OFF

SW1-5

OFF

SW1-6

OFF

SW1-7

SW1-8

OFF

100

101

102

103

104

105

OFF

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. Switch Settings for SW1 D-Type Control (Continued)

SWITCH SETTING

SPECTRA

ADDRESS

SW1-1

OFF

SW1-2

SW1-3

OFF

SW1-4

SW1-5

OFF

SW1-6

OFF

SW1-7

OFF

SW1-8

OFF

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

OFF

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. Switch Settings for SW1 D-Type Control (Continued)

SWITCH SETTING

SPECTRA

ADDRESS

SW1-1

SW1-2

OFF

SW1-3

SW1-4

SW1-5

OFF

SW1-6

OFF

SW1-7

OFF

SW1-8

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

OFF

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. Switch Settings for SW1 D-Type Control (Continued)

SWITCH SETTING

SPECTRA

ADDRESS

SW1-1

OFF

SW1-2

OFF

SW1-3

OFF

SW1-4

OFF

SW1-5

SW1-6

SW1-7

OFF

SW1-8

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

OFF

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. Switch Settings for SW1 D-Type Control (Continued)

SWITCH SETTING

SPECTRA

ADDRESS

SW1-1

SW1-2

SW1-3

OFF

SW1-4

OFF

SW1-5

SW1-6

OFF

SW1-7

SW1-8

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

OFF

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. Switch Settings for SW1 D-Type Control (Continued)

SWITCH SETTING

SPECTRA

ADDRESS

SW1-1

OFF

SW1-2

SW1-3

SW1-4

OFF

SW1-5

SW1-6

SW1-7

SW1-8

246

247

248

249

250

251

252

253

254

OFF

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Started

Once installed, apply power to the Spectra IV/Spectra IV SE dome system. The system will start a configuration sequence.

When configuration is done, the following information is displayed:

Pelco Spectra IV/Spectra IV SE

Version X.XX

D Address: 1

P Address: 2

Comm 2400, N, 8, 1

CONFIGURE DONE

This information will remain on the monitor until dome operation begins.

Note: When installing a Spectra IV dome drive in a Spectra III^™back box for the first time, a message appears. When the

installation is complete, the dome drive will continue with a normal configuration sequence.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

How to Operate Your Dome System

Operation

Pan and Tilt

Zoom Far

How to Control

Move the joystick or press the direction keys left/right and up/down.

To zoom far:

1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the optical zoom

limit.

2. Release the button or joystick for one second.

3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you

have the picture you want or reach the digital zoom¹limit.

Zoom Wide

Scanning

Press the Zoom Wide button or turn the joystick counterclockwise.

Stop Scan

Preset 96

Preset 97

Preset 98

Preset 99

Random Scan

Frame Scan

Auto Scan

Presets

Patterns²

Zones

Refer to the documentation supplied with the control system.

Refer to Zones on page 64 and to the documentation supplied with the control system.

Refer to Alarms on page 68.

Alarms

Auto Flip

Turn on or off in the programming menu. Refer to Auto Flip on page 50.

¹Digital zoom magnifies the image electronically and the picture may appear pixilated. The larger the digital zoom limit the greater the

reduction in resolution.

²The dome cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

QUICK PROGRAMMING GUIDE

Access main menu (preset 95). Refer to Accessing Main Menu (Preset 95) on page 21.

Use the joystick to position the cursor beside menu selection.

Note: If your controller does not have a joystick, use the up or down key.

Press Iris Open, the submenu/cursor moves to the right.

Move the joystick up or down to view selections.

Press Iris Open to make a selection.

Press Iris Close to cancel a selection.

ACCESSING MAIN MENU (PRESET 95)

You can call up the main menu on your monitor by programming (setting or creating) preset 95 (preset 28 in AD32-preset

mode).

Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for

programming preset 95 are given below for various Pelco controllers.

CM6700/CM6800

1. Enter the number of the Spectra IV/Spectra IV SE dome system and press the CAM key.

2. Enter 95 and hold the PRESET key for two seconds.

3. In the Edit Preset menu, go to SET and press the ACK key. The main menu appears.

KBD200A/KBD300A (Direct Mode Only)

1. Enter 95.

2. Hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

CM9500

1. Enter the number of the Spectra IV/Spectra IV SE dome system and press the CAM key. The main menu appears.

2. Highlight SETUP in the main menu and press the SELECT key.

3. Highlight CAM in the Setup menu and press the SELECT key.

4. Highlight PRESET in the Camera menu and press the SELECT key.

5. Enter 95 and press the F1 key. The main menu appears.

CM9740/CM9760/CM9770/CM9780

1. Press the ESCAPE key to open the main menu. Select DEF. The Define submenu appears.

2. Enter your four-digit PIN if this is your first time entering this mode.

3. Enter 95 and select PRST. The main menu appears on the monitor.

4. Select the Quit icon to return to the default menu.

KBD4000/KBD4002

1. Press the SPOT MONITOR key.

2. Enter 95, then hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

MPT9500

Standard Coaxitron Mode

1. Enter 95 and press the PRESET SET key.

2. Position the asterisk in the YES row and press the F1 key. The main menu appears.

Extended Coaxitron or RS-485 Mode

1. Enter 95 and press the PRESET SET key.

2. Press the F2 key. The main menu appears.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

NET300/NET350/NET4001A

1. Check the Set box.

2. Click the preset 95 button. The main menu appears.

ENDURA WORKSTATION

1. Right-click in the video pane of the Spectra IV/Spectra IV SE dome system.

2. Click Preset and then click Select Preset.

3. Enter 95 and then click OK.

VCD5000

1. Enter 95 for the preset action. The shortcuts menu appears.

2. Press the Preset button on the KBD5000.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

16X LowLight Color Menu Tree

SPECTRA IV

LANGUAGE

ENGLISH

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

SYSTEM INFORMATION

DISPLAY SETUP

SERIAL #

XXXXXXXXXXXXXX

XX-XXXX

PRESET LABEL

2 (SECS)

OFF

DOME DRIVE MODEL

BACK BOX MEMORY

SOFTWARE VERSION

BUILD

ZONE LABEL

ZOOM

AVAILABLE

XX.X

AZIMUTH/ELEVATION

DIRECTION

FONT VERSION

COMM

XX.X

ALARM MESSAGE

DATE/TIME

2 (SECS)

XXXXXXXXXX

D ADDRESS

EVENT LABEL

2 (SECS)

P ADDRESS

CM95OO MODE

32 PRESETS

OFF

RESTORE FACTORY DEFAULTS

PROTOCOL

DIPSWITCH INFORMATION

PRESSURIZED*

X.XX

LABEL POSITION

12345678

1234567890

SW1[--------] SW2[----------]

[ZONE LABEL-------]

[PRESET LABEL-------]

[ALARM 1-------]

ADDITIONAL

SW1 1-8:

D ADDRESS 1

FREE MEMORY

LATEST RESET

XXXXXX

[ALERT MESSAGE---]*

P ADDRESS 1

POWER ON

SW2 1 : 32 PRESETS. OFF

SW2 2 : CM9500 MODE. OFF

SW2 3 : COAX SPIV

SW2 4-5 : RS422 <->

AZIMUTH ZERO OFFSET

MOTOR ACTIVE

CAMERA ACTIVE

VIDEO LEVEL

0°

YES

SAVE AND EXIT

CANCEL AND EXIT

HELP

YES

NORMAL

XXXX-XXXX

ENGLISH X.XX

XXX/-XX

SW2 6-8 : COMM. 2400.N.8.1

SW2 9 : UTC SOURCE. COAX

SW2 10 : TX/RX TERM.. OFF

CAMERA MODEL

LANGUAGE 1

XXX.XX

. . .

LANGUAGE 10

ITALIANO X.XX

PRESS IRIS OPEN TO CONTINUE

CAMERA

ADVANCED SETTINGS

MOTION

POWER UP

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

OFF

SUTTER SPEED

AGC LIMIT

AUTO

AUTO FLIP

POWER UP ACTION

AUTO

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

XXXX

AUTO IRIS

AUTO

ZOOM SPEED

LOW LIGHT LIMIT

XXXX

XXXXXX

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

NONE

AUTO

255

OFF

HIGH

SCAN SPEED DEG/S

PRESET FREEZE FRAME

LIMIT STOPS

ZONES

WINDOW BLANKING

SET WINDOWS

ALARMS

ZONE NUMBER

STYLE

GRAY

OFF

WINDOW NUMBER

ENABLE WINDOW

REVERSE

ALARM CONTACT

***ZONE NOT DEFINED***

BLANK ALL ABOVE

BLANK ALL BELOW

ZONE ENABLED

ZONE BLANKING

OFF

CLEAR WINDOW

ALERT*

REPEAT

CURRENT READING

CLEAR

PASSWORD

CONSTANT

TEMPERATURE

DEWPOINT

PRESURE

CLEAR ALL ZONES

ENABLE PASSWORD

OFF

ACK ACTION

ALWAYS ON

CLEAR ALL PRESETS

CLEAR ALL PATTERNS

ACTIVATE AUX

RESET ALERT

REFRESH

CLEAR ALL WINDOW BLANKING

CLEAR ALL EVENTS

RESTORE FACTORY DEFAULTS

*This setting applies only to Pressurized Spectra IV dome systems. Spectra IV systems that are not pressurized will not display this menu item.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

LINE SYNC

PRESETS

PATTERNS

LINE SYNC

LINE SYNC PHASE

PRESET NUMBER

PATTERN NUMBER

***PRESET NOT DEFINED***

REFERENCE INFO

PATTERN USAGE

REMAINING

100%

REFERENCE INFORMATION

AZIMUTH

ELEVATION

ZOOM

AUX

TITLE TEXT

AUX 1 MODE

TOGGLE

ENABLE TITLE TEXT

DWELL TIME (SECS)

AUX 2 MODE

TOGGLE

DWELL TIME (SECS)

EDIT THE PASSWORD

CLOCK

EVENT

EDIT EVENT

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXYZ.,-/

abcdefghij

klmnopqrst

uvwxyz#&:*

TIME BASE

INTERNAL CLOCK

12 HOUR

EVENT TYPE

ALL EVENTS

EVENT LABEL

EVENT01

TIME FORMAT

SET TIME

EVENT LABEL

NEW

12:00 AM

EVENT ACTIVE

EVENT TIME

EVENT OCCURS

SUNDAY

12:00 AM

DATE FORMAT

SET DATE

DAYLIGHT SAVINGS

MM/DD/YYYY

00/00/0000

OFF

MONDAY

TUESDAY

HOLIDAY

WEDNESDAY

THURSDAY

FRIDAY

SATURDAY

HOLIDAY

SKIP HOLIDAYS

EVENT TYPE

PRESET

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

18X LowLight Day/Night Menu Tree

SPECTRA IV

LANGUAGE

ENGLISH

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

SYSTEM INFORMATION

DISPLAY SETUP

SERIAL #

XXXXXXXXXXXXXX

XX-XXXX

PRESET LABEL

2 (SECS)

OFF

DOME DRIVE MODEL

BACK BOX MEMORY

SOFTWARE VERSION

BUILD

ZONE LABEL

ZOOM

AVAILABLE

XX.X

AZIMUTH/ELEVATION

DIRECTION

FONT VERSION

COMM

XX.X

ALARM MESSAGE

DATE/TIME

2 (SECS)

XXXXXXXXXX

D ADDRESS

EVENT LABEL

2 (SECS)

P ADDRESS

CM95OO MODE

32 PRESETS

OFF

RESTORE FACTORY DEFAULTS

PROTOCOL

DIPSWITCH INFORMATION

PRESSURIZED*

X.XX

LABEL POSITION

12345678

1234567890

SW1[--------] SW2[----------]

[ZONE LABEL-------]

[PRESET LABEL-------]

[ALARM 1-------]

ADDITIONAL

SW1 1-8:

D ADDRESS 1

FREE MEMORY

LATEST RESET

AZIMUTH ZERO OFFSET

MOTOR ACTIVE

CAMERA ACTIVE

VIDEO LEVEL

XXXXXX

POWER ON

0°

[ALERT MESSAGE---]*

P ADDRESS 1

SW2 1 : 32 PRESETS. OFF

SW2 2 : CM9500 MODE. OFF

SW2 3 : COAX SPIV

SW2 4-5 : RS422 <->

SAVE AND EXIT

CANCEL AND EXIT

HELP

YES

NORMAL

XXXX-XXXX

ENGLISH X.XX

XXX/-XX

SW2 6-8 : COMM. 2400.N.8.1

SW2 9 : UTC SOURCE. COAX

SW2 10 : TX/RX TERM.. OFF

CAMERA MODEL

LANGUAGE 1

XXX.XX

. . .

LANGUAGE 10

ITALIANO X.XX

PRESS IRIS OPEN TO CONTINUE

CAMERA

ADVANCED SETTINGS

MOTION

POWER UP

AUTO FOCUS

OFF

SUTTER SPEED

AGC LIMIT

AUTO

AUTO FLIP

POWER UP ACTION

AUTO

SURE FOCUS

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

ZOOM LIMIT

XXXX

XXXXXX

XXXX

OFF

AUTO IRIS

AUTO

ZOOM SPEED

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

NONE

AUTO

LOW LIGHT LIMIT

IR CUT FILTER

255

OFF

HIGH

OFF

SCAN SPEED DEG/S

PRESET FREEZE FRAME

LIMIT STOPS

LOW LIGHT FOCUS

AUTO IR LEVEL

AUTO

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

FIELD ALIGN

LOW LUX NOISE REDUCTION

ZONES

WINDOW BLANKING

SET WINDOWS

ZONE NUMBER

STYLE

GRAY

OFF

WINDOW NUMBER

ENABLE WINDOW

REVERSE

***ZONE NOT DEFINED***

BLANK ALL ABOVE

BLANK ALL BELOW

ZONE ENABLED

ZONE BLANKING

OFF

CLEAR WINDOW

ALERT*

REPEAT

CURRENT READING

CLEAR

PASSWORD

CONSTANT

TEMPERATURE

DEWPOINT

PRESURE

CLEAR ALL ZONES

ENABLE PASSWORD

OFF

ACK ACTION

ALWAYS ON

CLEAR ALL PRESETS

CLEAR ALL PATTERNS

ACTIVATE AUX

RESET ALERT

REFRESH

CLEAR ALL WINDOW BLANKING

CLEAR ALL EVENTS

RESTORE FACTORY DEFAULTS

*This setting applies only to Pressurized Spectra IV dome systems. Spectra IV systems that are not pressurized will not display this menu item.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

LINE SYNC

PRESETS

PATTERNS

LINE SYNC

LINE SYNC PHASE

PRESET NUMBER

PATTERN NUMBER

***PRESET NOT DEFINED***

REFERENCE INFO

PATTERN USAGE

REMAINING

100%

REFERENCE INFORMATION

AZIMUTH

ELEVATION

ZOOM

ALARMS

AUX

TITLE TEXT

ALARM CONTACT

AUX 1 MODE

TOGGLE

ENABLE TITLE TEXT

DWELL TIME (SECS)

AUX 2 MODE

TOGGLE

DWELL TIME (SECS)

EDIT THE PASSWORD

CLOCK

EVENT

EDIT EVENT

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXYZ.,-/

abcdefghij

klmnopqrst

uvwxyz#&:*

TIME BASE

INTERNAL CLOCK

12 HOUR

EVENT TYPE

ALL EVENTS

EVENT LABEL

EVENT01

TIME FORMAT

SET TIME

EVENT LABEL

NEW

12:00 AM

EVENT ACTIVE

EVENT TIME

EVENT OCCURS

SUNDAY

12:00 AM

DATE FORMAT

SET DATE

DAYLIGHT SAVINGS

MM/DD/YYYY

00/00/0000

OFF

MONDAY

TUESDAY

HOLIDAY

WEDNESDAY

THURSDAY

FRIDAY

SATURDAY

HOLIDAY

SKIP HOLIDAYS

EVENT TYPE

PRESET

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

22X EXview LowLight Color Menu Tree

SPECTRA IV

LANGUAGE

ENGLISH

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

SYSTEM INFORMATION

DISPLAY SETUP

SERIAL #

XXXXXXXXXXXXXX

XX-XXXX

PRESET LABEL

2 (SECS)

OFF

DOME DRIVE MODEL

BACK BOX MEMORY

SOFTWARE VERSION

BUILD

ZONE LABEL

ZOOM

AVAILABLE

XX.X

AZIMUTH/ELEVATION

DIRECTION

FONT VERSION

COMM

XX.X

ALARM MESSAGE

DATE/TIME

2 (SECS)

XXXXXXXXXX

D ADDRESS

EVENT LABEL

2 (SECS)

P ADDRESS

CM95OO MODE

32 PRESETS

OFF

RESTORE FACTORY DEFAULTS

PROTOCOL

DIPSWITCH INFORMATION

PRESSURIZED*

X.XX

LABEL POSITION

12345678

1234567890

SW1[--------] SW2[----------]

[ZONE LABEL-------]

[PRESET LABEL-------]

[ALARM 1-------]

ADDITIONAL

SW1 1-8:

D ADDRESS 1

FREE MEMORY

LATEST RESET

XXXXXX

[ALERT MESSAGE---]*

P ADDRESS 1

POWER ON

SW2 1 : 32 PRESETS. OFF

SW2 2 : CM9500 MODE. OFF

SW2 3 : COAX SPIV

SW2 4-5 : RS422 <->

AZIMUTH ZERO OFFSET

MOTOR ACTIVE

CAMERA ACTIVE

VIDEO LEVEL

0°

YES

SAVE AND EXIT

CANCEL AND EXIT

HELP

YES

NORMAL

XXXX-XXXX

ENGLISH X.XX

XXX/-XX

SW2 6-8 : COMM. 2400.N.8.1

SW2 9 : UTC SOURCE. COAX

SW2 10 : TX/RX TERM.. OFF

CAMERA MODEL

LANGUAGE 1

XXX.XX

. . .

LANGUAGE 10

ITALIANO X.XX

PRESS IRIS OPEN TO CONTINUE

CAMERA

ADVANCED SETTINGS

MOTION

POWER UP

TYPE OF LIGHTING

AUTO FOCUS

SUTTER SPEED

AGC LIMIT

AUTO

AUTO FLIP

POWER UP ACTION

AUTO

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

SURE FOCUS

OFF

AUTO IRIS

AUTO

ZOOM LIMIT

XXXX

XXXXXX

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

NONE

AUTO

ZOOM SPEED

255

OFF

SCAN SPEED DEG/S

PRESET FREEZE FRAME

LIMIT STOPS

LOW LIGHT LIMIT

B GAIN

BACKLIGHT COMP

ZONES

WINDOW BLANKING

SET WINDOWS

ZONE NUMBER

STYLE

GRAY

OFF

WINDOW NUMBER

ENABLE WINDOW

REVERSE

***ZONE NOT DEFINED***

BLANK ALL ABOVE

BLANK ALL BELOW

ZONE ENABLED

ZONE BLANKING

OFF

CLEAR WINDOW

ALERT*

REPEAT

CURRENT READING

CLEAR

PASSWORD

CONSTANT

TEMPERATURE

DEWPOINT

PRESURE

CLEAR ALL ZONES

ENABLE PASSWORD

OFF

ACK ACTION

ALWAYS ON

CLEAR ALL PRESETS

CLEAR ALL PATTERNS

ACTIVATE AUX

RESET ALERT

REFRESH

CLEAR ALL WINDOW BLANKING

CLEAR ALL EVENTS

RESTORE FACTORY DEFAULTS

*This setting applies only to Pressurized Spectra IV dome systems. Spectra IV systems that are not pressurized will not display this menu item.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

LINE SYNC

PRESETS

PATTERNS

LINE SYNC

LINE SYNC PHASE

PRESET NUMBER

PATTERN NUMBER

***PRESET NOT DEFINED***

REFERENCE INFO

PATTERN USAGE

REMAINING

100%

REFERENCE INFORMATION

AZIMUTH

ELEVATION

ZOOM

CUSTOM CAMERA SETTINGS

ALARMS

ALARM SETTINGS

AUX

TITLE TEXT

RESUME

OFF

ALARM NUMBER

LOW

NONE

AUX 1 MODE

TOGGLE

ENABLE TITLE TEXT

SEQUENCE (SECS)

RESET DELAY (SECS)

ALARM PRIORITY

ALARM ACTION

ACTIVATE AUX

DWELL TIME (SECS)

AUX 2 MODE

TOGGLE

DWELL TIME (SECS)

ALARM CONTACT

N/O

EDIT THE PASSWORD

CLOCK

EVENT

EDIT EVENT

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXYZ.,-/

abcdefghij

klmnopqrst

uvwxyz#&:*

TIME BASE

INTERNAL CLOCK

12 HOUR

EVENT TYPE

ALL EVENTS

EVENT LABEL

EVENT01

TIME FORMAT

SET TIME

EVENT LABEL

NEW

12:00 AM

EVENT ACTIVE

EVENT TIME

EVENT OCCURS

SUNDAY

12:00 AM

DATE FORMAT

SET DATE

DAYLIGHT SAVINGS

MM/DD/YYYY

00/00/0000

OFF

MONDAY

TUESDAY

HOLIDAY

WEDNESDAY

THURSDAY

FRIDAY

SATURDAY

HOLIDAY

SKIP HOLIDAYS

EVENT TYPE

PRESET

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

23X LowLight Day/Night Menu Tree

SPECTRA IV

LANGUAGE

ENGLISH

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

SYSTEM INFORMATION

DISPLAY SETUP

SERIAL #

XXXXXXXXXXXXXX

XX-XXXX

PRESET LABEL

2 (SECS)

OFF

DOME DRIVE MODEL

BACK BOX MEMORY

SOFTWARE VERSION

BUILD

ZONE LABEL

ZOOM

AVAILABLE

XX.X

AZIMUTH/ELEVATION

DIRECTION

FONT VERSION

COMM

XX.X

ALARM MESSAGE

DATE/TIME

2 (SECS)

XXXXXXXXXX

D ADDRESS

EVENT LABEL

2 (SECS)

P ADDRESS

CM95OO MODE

32 PRESETS

OFF

RESTORE FACTORY DEFAULTS

PROTOCOL

DIPSWITCH INFORMATION

PRESSURIZED*

X.XX

LABEL POSITION

12345678

1234567890

SW1[--------] SW2[----------]

[ZONE LABEL-------]

[PRESET LABEL-------]

[ALARM 1-------]

ADDITIONAL

SW1 1-8:

D ADDRESS 1

FREE MEMORY

LATEST RESET

AZIMUTH ZERO OFFSET

MOTOR ACTIVE

CAMERA ACTIVE

VIDEO LEVEL

XXXXXX

POWER ON

0°

[ALERT MESSAGE---]*

P ADDRESS 1

SW2 1 : 32 PRESETS. OFF

SW2 2 : CM9500 MODE. OFF

SW2 3 : COAX SPIV

SW2 4-5 : RS422 <->

SAVE AND EXIT

CANCEL AND EXIT

HELP

YES

NORMAL

XXXX-XXXX

ENGLISH X.XX

XXX/-XX

SW2 6-8 : COMM. 2400.N.8.1

SW2 9 : UTC SOURCE. COAX

SW2 10 : TX/RX TERM.. OFF

CAMERA MODEL

LANGUAGE 1

XXX.XX

. . .

LANGUAGE 10

ITALIANO X.XX

PRESS IRIS OPEN TO CONTINUE

CAMERA

ADVANCED SETTINGS

MOTION

POWER UP

TYPE OF LIGHTING

AUTO FOCUS

SUTTER SPEED

AGC LIMIT

AUTO

AUTO FLIP

POWER UP ACTION

AUTO

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

SURE FOCUS

OFF

AUTO IRIS

AUTO

ZOOM LIMIT

XXXX

XXXXXX

XXXX

OFF

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

NONE

AUTO

ZOOM SPEED

255

OFF

HIGH

OFF

SCAN SPEED DEG/S

PRESET FREEZE FRAME

LIMIT STOPS

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

AUTO

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

FIELD ALIGN

LOW LUX NOISE REDUCTION

ZONES

WINDOW BLANKING

SET WINDOWS

ZONE NUMBER

STYLE

GRAY

OFF

WINDOW NUMBER

ENABLE WINDOW

REVERSE

***ZONE NOT DEFINED***

BLANK ALL ABOVE

BLANK ALL BELOW

ZONE ENABLED

ZONE BLANKING

OFF

CLEAR WINDOW

ALERT*

REPEAT

CURRENT READING

CLEAR

PASSWORD

CONSTANT

TEMPERATURE

DEWPOINT

PRESURE

CLEAR ALL ZONES

ENABLE PASSWORD

OFF

ACK ACTION

ALWAYS ON

CLEAR ALL PRESETS

CLEAR ALL PATTERNS

ACTIVATE AUX

RESET ALERT

REFRESH

CLEAR ALL WINDOW BLANKING

CLEAR ALL EVENTS

RESTORE FACTORY DEFAULTS

*This setting applies only to Pressurized Spectra IV dome systems. Spectra IV systems that are not pressurized will not display this menu item.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

LINE SYNC

PRESETS

EDIT DETECTION AREAS

PATTERNS

LINE SYNC

LINE SYNC PHASE

PRESET NUMBER

DETECTION AREA 1

PATTERN NUMBER

***PRESET NOT DEFINED***

LOCATION

SENSITIVITY

MEDIUM

DETECTION AREA 2

LOCATION

SENSITIVITY

MEDIUM

REFERENCE INFO

PATTERN USAGE

REMAINING

100%

DETECTION AREA 3

LOCATION

REFERENCE INFORMATION

AZIMUTH

ELEVATION

ZOOM

SENSITIVITY

MEDIUM

DETECTION AREA 4

LOCATION

SENSITIVITY

MEDIUM

ALARMS

ALARM SETTINGS

AUX

TITLE TEXT

RESUME

OFF

ALARM NUMBER

ALARM PRIORITY

ALARM ACTION

ACTIVATE AUX

ALARM CONTACT

LOW

NONE

AUX 1 MODE

TOGGLE

ENABLE TITLE TEXT

SEQUENCE (SECS)

RESET DELAY (SECS)

DWELL TIME (SECS)

AUX 2 MODE

TOGGLE

DWELL TIME (SECS)

N/O

EDIT THE PASSWORD

CLOCK

EVENT

EDIT EVENT

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXYZ.,-/

abcdefghij

klmnopqrst

uvwxyz#&:*

TIME BASE

INTERNAL CLOCK

12 HOUR

EVENT TYPE

ALL EVENTS

EVENT LABEL

EVENT01

TIME FORMAT

SET TIME

EVENT LABEL

NEW

12:00 AM

EVENT ACTIVE

EVENT TIME

EVENT OCCURS

SUNDAY

12:00 AM

DATE FORMAT

SET DATE

DAYLIGHT SAVINGS

MM/DD/YYYY

00/00/0000

OFF

MONDAY

TUESDAY

HOLIDAY

WEDNESDAY

THURSDAY

FRIDAY

SATURDAY

HOLIDAY

SKIP HOLIDAYS

EVENT TYPE

PRESET

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

35X LowLight Day/Night Menu Tree

SPECTRA IV

LANGUAGE

ENGLISH

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

SYSTEM INFORMATION

DISPLAY SETUP

SERIAL #

XXXXXXXXXXXXXX

XX-XXXX

PRESET LABEL

2 (SECS)

OFF

DOME DRIVE MODEL

BACK BOX MEMORY

SOFTWARE VERSION

BUILD

ZONE LABEL

ZOOM

AVAILABLE

XX.X

AZIMUTH/ELEVATION

DIRECTION

FONT VERSION

COMM

XX.X

ALARM MESSAGE

DATE/TIME

2 (SECS)

XXXXXXXXXX

D ADDRESS

EVENT LABEL

2 (SECS)

P ADDRESS

CM95OO MODE

32 PRESETS

OFF

RESTORE FACTORY DEFAULTS

PROTOCOL

DIPSWITCH INFORMATION

PRESSURIZED*

X.XX

LABEL POSITION

12345678

1234567890

SW1[--------] SW2[----------]

[ZONE LABEL-------]

[PRESET LABEL-------]

[ALARM 1-------]

ADDITIONAL

SW1 1-8:

D ADDRESS 1

FREE MEMORY

LATEST RESET

AZIMUTH ZERO OFFSET

MOTOR ACTIVE

CAMERA ACTIVE

VIDEO LEVEL

XXXXXX

POWER ON

0°

[ALERT MESSAGE---]*

P ADDRESS 1

SW2 1 : 32 PRESETS. OFF

SW2 2 : CM9500 MODE. OFF

SW2 3 : COAX SPIV

SW2 4-5 : RS422 <->

SAVE AND EXIT

CANCEL AND EXIT

HELP

YES

NORMAL

XXXX-XXXX

ENGLISH X.XX

XXX/-XX

SW2 6-8 : COMM. 2400.N.8.1

SW2 9 : UTC SOURCE. COAX

SW2 10 : TX/RX TERM.. OFF

CAMERA MODEL

LANGUAGE 1

XXX.XX

. . .

LANGUAGE 10

ITALIANO X.XX

PRESS IRIS OPEN TO CONTINUE

CAMERA

ADVANCED SETTINGS

MOTION

POWER UP

TYPE OF LIGHTING

AUTO FOCUS

SUTTER SPEED

AGC LIMIT

AUTO

AUTO FLIP

POWER UP ACTION

AUTO

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

SURE FOCUS

OFF

AUTO IRIS

AUTO

ZOOM LIMIT

XXXX

XXXXXX

XXXX

OFF

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

NONE

AUTO

ZOOM SPEED

255

OFF

HIGH

SCAN SPEED DEG/S

PRESET FREEZE FRAME

LIMIT STOPS

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

AUTO

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

SENSOR SCAN MODE

FIELD ALIGN

PROGRESSIVE

OFF

E. IMAGE STABILIZER

IMAGE ENHANCEMENT

OFF

DEFAULT

LOW LUX NOISE REDUCTION

WIDE DYNAMIC RANGE

OFF

ZONES

WINDOW BLANKING

SET WINDOWS

ZONE NUMBER

STYLE

GRAY

OFF

WINDOW NUMBER

ENABLE WINDOW

REVERSE

***ZONE NOT DEFINED***

BLANK ALL ABOVE

BLANK ALL BELOW

ZONE ENABLED

ZONE BLANKING

OFF

CLEAR WINDOW

ALERT*

REPEAT

CURRENT READING

CLEAR

PASSWORD

CONSTANT

TEMPERATURE

DEWPOINT

PRESURE

CLEAR ALL ZONES

ENABLE PASSWORD

OFF

ACK ACTION

ALWAYS ON

CLEAR ALL PRESETS

CLEAR ALL PATTERNS

ACTIVATE AUX

RESET ALERT

REFRESH

CLEAR ALL WINDOW BLANKING

CLEAR ALL EVENTS

RESTORE FACTORY DEFAULTS

*This setting applies only to Pressurized Spectra IV dome systems. Spectra IV systems that are not pressurized will not display this menu item.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

LINE SYNC

PRESETS

EDIT DETECTION AREAS

PATTERNS

LINE SYNC

LINE SYNC PHASE

PRESET NUMBER

DETECTION AREA 1

PATTERN NUMBER

***PRESET NOT DEFINED***

LOCATION

SENSITIVITY

MEDIUM

DETECTION AREA 2

LOCATION

SENSITIVITY

MEDIUM

REFERENCE INFO

PATTERN USAGE

REMAINING

100%

DETECTION AREA 3

LOCATION

REFERENCE INFORMATION

AZIMUTH

SENSITIVITY

MEDIUM

DETECTION AREA 4

LOCATION

ELEVATION

SENSITIVITY

MEDIUM

ZOOM

CUSTOM CAMERA SETTINGS

ALARMS

ALARM SETTINGS

AUX

TITLE TEXT

RESUME

OFF

ALARM NUMBER

ALARM PRIORITY

ALARM ACTION

ACTIVATE AUX

ALARM CONTACT

LOW

NONE

AUX 1 MODE

TOGGLE

ENABLE TITLE TEXT

SEQUENCE (SECS)

RESET DELAY (SECS)

DWELL TIME (SECS)

AUX 2 MODE

TOGGLE

DWELL TIME (SECS)

N/O

EDIT EVENT

EVENT LABEL

EVENT01

EDIT THE PASSWORD

CLOCK

EVENT

EVENT ACTIVE

EVENT TIME

EVENT OCCURS

SUNDAY

12:00 AM

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXYZ.,-/

abcdefghij

klmnopqrst

uvwxyz#&:*

TIME BASE

INTERNAL CLOCK

12 HOUR

EVENT TYPE

ALL EVENTS

TIME FORMAT

SET TIME

EVENT LABEL

NEW

12:00 AM

MONDAY

DATE FORMAT

SET DATE

MM/DD/YYYY

00/00/0000

OFF

TUESDAY

WEDNESDAY

THURSDAY

FRIDAY

DAYLIGHT SAVINGS

SATURDAY

HOLIDAY

SKIP HOLIDAYS

EVENT TYPE

PRESET

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Language

The language for the on-screen menus is selectable. Available languages include English,

Spanish, French, German, Italian, Portuguese, Russian, Polish, Turkish, and Czech. The factory

default language is English.

SPECTRA IV

LANGUAGE

ACK ALERT*

To change the display language:

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

1. Use the joystick to position the cursor beside LANGUAGE.

2. Press Iris Open. The cursor moves to the right, beside the current, selected language.

EXIT

3. Move the joystick up or down to view selections. Press Iris Open to enter selection.

All on-screen menus are changed to the selected language.

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

System Information

The System Information menu displays the dome drive model, software version, available

SPECTRA IV

memory, DIP switch information, and other diagnostic information.

System settings cannot be changed using this menu; this information is for reference only.

Use the following steps to display the System Information menu:

LANGUAGE

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

1. Use the joystick to position the cursor beside SYSTEM INFORMATION.

2. Press Iris Open. The SYSTEM INFORMATION menu opens.

EXIT

DIP SWITCH INFORMATION

SYSTEM INFORMATION

SERIAL #

The DIP Switch Information menu displays the dome drive’s current DIP switch settings. This

provides a way to remotely view the DIP switch settings without removing the dome drive from

the back box.

DOME DRIVE MODEL

BACK BOX MEMORY

SOFTWARE VERSION

BUILD

FONT VERSION

DIP SWITCH INFORMATION

COMM

12345678

1234567890

D ADDRESS

P ADDRESS

CM9500 MODE

32 PRESETS

PROTOCOL

SW1[- - - - - - - -] SW2[- - - - - - - - - -]

SW1 1-8 :

D ADDRESS 1

P ADDRESS 1

PRESSURIZED*

SW2 1 : 32 PRESETS. OFF

SW2 2 : CM9500 MODE. OFF

SW2 3 : COAX SPIV

SW2 4-5 : RS422 <->

BACK

EXIT

SW2 6-8 : COMM. 2400.N.8.1

SW2 9 : UTC SOURCE. COAX

SW2 10 : TX/RX TERM.. OFF

PRESS IRIS OPEN TO CONTINUE

ADDITIONAL

FREE MEMORY

LAST RESET

AZIMUTH ZERO OFFSET

MOTOR ACTIVE

CAMERA ACTIVE

VIDEO LEVEL

CAMERA MODEL

LANGUAGE 1

LANGUAGE 2

LANGUAGE 3

LANGUAGE 4

LANGUAGE 5

LANGUAGE 6

LANGUAGE 7

LANGUAGE 8

LANGUAGE 9

LANGUAGE 10

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Display Setup

Display setup allows you to program how labels are displayed on the monitor. The following

labels are available:

SPECTRA IV

LANGUAGE

PRESET LABEL: Identifies preset.

ZONE LABEL: Identifies zone.

ACK ALERT*

ZOOM: Identifies the amount of magnification.

AZIMUTH¹/ELEVATION²: Amount of pan from zero degrees vertical and the amount of tilt from

zero degrees horizontal.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

DIRECTION: Displays compass direction.

ALARM MESSAGE: Displays activated alarm.

DATE/TIME: Displays current date and time.

EVENT LABEL: Displays activated event.

DISPLAY SETUP

PRESET LABEL

ZONE LABEL

A preset label is displayed when a preset is called. A zone label is displayed when the system

moves into a zone. The zoom ratio label is displayed when zoom is activated. Azimuth/elevation

and direction labels are displayed when pan/tilt is activated. An alarm message appears on the

monitor when an alarm occurs. An event label appears on the monitor when an event occurs.

ZOOM

AZIMUTH/ELEVATION

DIRECTION

ALARM MESSAGE

DATE/TIME

EVENT LABEL

RESTORE FACTORY DEFAULTS

The following settings are available for each label except date and time:

OFF: Label is not displayed when activated.

BACK

EXIT

CONSTANT: The label is continually displayed when activated.

2 SECONDS: The label is displayed for 2 seconds after activation.

5 SECONDS: The label is displayed for 5 seconds after activation.

10 SECONDS: The label is displayed for 10 seconds after activation.

The settings for date and time are ON or OFF.

¹Azimuth is the pan angle from zero to 359 degrees.

²Elevation is the tilt position from zero (horizon) to -90 degrees.

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

LABEL POSITIONS

Labels can be placed anywhere on the monitor. This feature allows you to customize the

appearance of your monitor screen.

SPECTRA IV

LANGUAGE

ACK ALERT*

The following labels are not set at fixed positions:

PRESET LABEL

ZONE LABEL

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

ALARM 1

EXIT

ZOOM RATIO - XXX.XX

AZIMUTH¹/ELEVATION²- XXX°/-XX°

DIRECTION - NE

DISPLAY SETUP

ALERT MESSAGE³*

PRESET LABEL

ZONE LABEL

TITLE TEXT

ZOOM

AZIMUTH/ELEVATION

DIRECTION

EVENT LABEL

ALARM MESSAGE

DATE/TIME

To set a label position:

EVENT LABEL

RESTORE FACTORY DEFAULTS

BACK

EXIT

1. Use the joystick to position the cursor beside a label.

2. Press Iris Open.

3. Use the joystick to move the label up, down, left, or right.

4. Press Iris Open.

LABEL POSITION

5. Repeat steps 1–4 to position other labels.

6. Position the cursor next to Save and Exit. Press Iris Open to save settings and exit the menu.

[ZONE LABEL-------]

[PRESET LABEL-------]

[ALARM 1-------]

[EVENT-------]

[ALERT MESSAGE-------]*

SAVE AND EXIT

CANCEL AND EXIT

HELP

XXX^o/-XXXo

XXX.XX

XX/XX/YYYY 00:00

¹Azimuth is the pan angle from zero to 359 degrees.

²Elevation is the tilt position from zero (horizon) to -90 degrees.

³The alert message is the warning displayed on the monitor if pressure, temperature, or dew point inside the

dome reach unacceptable levels.

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Dome Settings

CAMERA

TYPE OF LIGHTING

(Does not apply to 16X or 18X models.)

SPECTRA IV

LANGUAGE

ACK ALERT*

Pelco has calibrated settings that optimize the white balance and the picture for several lighting

conditions. There are three settings:

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

T1 (default): For use in outdoor applications.

T2: For use in indoor applications.

EXIT

T3: (Available only with 23X models.) For use in applications that use sodium lighting.

AUTO FOCUS

DOME SETTINGS

Auto focus allows the lens to remain in focus during zoom-in, zoom-out, and motion functions.

<ZONES>

There are two auto focus settings:

ON (default): If auto focus mode is set to ON, the camera will focus automatically when using

pan, tilt, and zoom (PTZ) functions.

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

OFF: Focus is operated manually. To focus, press the Focus Far or Focus Near button on the

controller.

Sure Focus

When sure focus is enabled and all PTZ motions are stopped, the camera will attempt to find a

fixed focus position and lock to an object in the scene. If a focus lock is acquired or a specific

amount of time has expired with no focus lock, the focus position remains fixed until PTZ is

resumed.

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

ZOOM LIMIT

SPECTRA IV

LANGUAGE

Zoom limit allows the user to define a limitation on the amount of telephoto zoom. The settings

vary depending on camera model.

ACK ALERT*

16X (Models DD4TC16 and DD4TC16-X)

The default setting is 32X. Cameras with 128X zoom (16X optical zoom and 8X digital zoom) can

be set for 16X, 32X, 64X, or 128X.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

18X (Models DD4CBW18 and DD4CBW18-X)

The default setting is 32X. Cameras with 216X zoom (18X optical zoom and 12X digital zoom) can

be set for 18X, 32X, 72X, or 144X, 180X, or 216X.

DOME SETTINGS

<ZONES>

<AUX>

22X (Models DD4C22, and DD4C22-X)

The default setting is 32X. Cameras with 264X zoom (22X optical zoom and 12X digital zoom) can

be set for 22X, 32X, 88X, 176X, 220X, or 264X.

23X (Models DD4CBW23 and DD4CBW23-X)

The default setting is 32X. Cameras with 276X zoom (23X optical zoom and 12X digital zoom) can

be set for 23X, 32X, 92X, 184X, 230X, 276X.

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

35X (Models DD4CBW35 and DD4CBW35-X)

The default setting is 70X. Cameras with 420X zoom (35X optical zoom and 12X digital zoom) can

be set for 35X, 70X, 140X, 280X, 350X, or 420X.

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

ZOOM SPEED

SPECTRA IV

LANGUAGE

Zoom speed allows the user to define how fast the dome will go from full wide zoom to the 16X,

18X, 22X, 23X, or 35X optical zoom.

ACK ALERT*

Available zoom speed settings for 16X models include:

HIGH: 1.9 seconds

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

MEDIUM (default): 3.6 seconds

LOW: 6.0 seconds

EXIT

Available zoom speed settings for 18X and 23X models include:

HIGH: 2.9 seconds

DOME SETTINGS

MEDIUM (default): 4.2 seconds

LOW: 5.8 seconds

<ZONES>

<AUX>

Available zoom speed settings for 22X models include:

HIGH: 2.4 seconds

MEDIUM (default): 3.9 seconds

LOW: 6.3 seconds

<ALERT>*

<CLEAR>

Available zoom speed settings for 35X models include:

HIGH: 3.2 seconds

<CLOCK>

<EVENT>

BACK

EXIT

MEDIUM (default): 4.6 seconds

LOW: 6.6 seconds

Note: When using the HIGH setting, the image may be out of focus until zooming stops.

CAMERA

LOW LIGHT LIMIT

Low light limit is the maximum duration, in fractions of a second, that the electronic shutter will

remain open in low light conditions. The default setting is 2.

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

Settings include the following:

2 = 1/2 second

4 = 1/4 second

8 = 1/8 second

30 = 1/30 second

60 = 1/60 second

15 = 1/15 second

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

IR CUT FILTER

(Applies only to 18X, 23X, and 35X models.)

SPECTRA IV

LANGUAGE

ACK ALERT*

The 18X, 23X, and 35X cameras have two modes of operation: color, and black-white. You can

increase sensitivity in low light conditions by switching to black-white mode (removing the IR cut

filter). Color mode is preferred in normal lighting conditions.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

The following are the settings for the IR cut filter:

EXIT

OFF: Manual operation is controlled by preset 88 (filter IN) and 89 (filter OUT).

AUTO (default): Automatic operation is controlled by the auto IR level setting.

IN: Images are always displayed in color mode.

DOME SETTINGS

OUT: Images are always displayed in black-white mode.

<ZONES>

<AUX>

Note: The IN and OUT settings are only available when editing camera settings through the

Presets menu (refer to Presets on page 57).

Low Light Focus

If you are using an IR illuminator, the low light focus feature of the camera can be tuned to

correspond to the setting of the illuminator.

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

There are three low light focus settings:

OFF (default): Low light focus is not activated.

850NM: Low light focus is tuned to 850 nm (nanometers).

950NM: Low light focus is tuned to 950 nm.

BACK

EXIT

CAMERA

Auto IR Level

TYPE OF LIGHTING

AUTO FOCUS

The auto IR level is the light level at which the infrared filter switches IN or OUT.

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

Following are the available settings for the auto IR level:

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

DUSK (default): Approximately 6 lux (black-white); approximately 13 lux (color).

DARK: Approximately 0.1 lux (black-white); approximately 2 lux (color).

Notes:

BACK

EXIT

• If backlight compensation is ON and the IR cut filter switches OUT in normal lighting

conditions, adjust the Auto IR Level to a darker setting. Refer to Backlight Compensation (BLC)

on page 45.

• Low light does not mean no light. Some type of illumination is required (street light, IR light,

etc.). The camera is not sensitive to IR light when the IR cut filter is IN.

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

ADVANCED CAMERA SETTINGS

SHUTTER SPEED

SPECTRA IV

LANGUAGE

Shutter speed is the duration of the electronic shutter. Program shutter speed to operate

automatically (Auto) or manually (Numeric Value).

ACK ALERT*

AUTO (default): The electronic shutter speed is set automatically by the amount of light sensed

by the camera.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

NUMERIC VALUE: Spectra IV/Spectra IV SE dome systems have several numerical shutter

speed settings. The higher the number, the faster the electronic shutter.

EXIT

The slowest shutter speed setting is 2 = 1/2 second.

The fastest setting is 30,000 = 1/30,000 second.

DOME SETTINGS

<ZONES>

<AUX>

Increasing the shutter speed lowers the light sensitivity and reduces the streaking of fast moving

objects.

Set the shutter speed to 100 if you are using an NTSC camera in a 50 Hz environment. This will

eliminate any flicker that may occur in the picture.

<ALERT>*

AGC LIMIT

<CLEAR>

<CLOCK>

<EVENT>

AGC limit allows users to adjust how the system balances AGC (automatic gain control) and

electronic shutter in low light conditions. As scene lighting decreases, the system will

automatically adjust, adding a mixture of AGC and slow shutter according to the AGC limit

setting. AGC limit can be set between 0 and 40, with 40 applying maximum AGC before slow

shutter. In contrast, setting AGC limit to 0 will force the system software to apply maximum slow

shutter (as defined by the low light limit setting) before any AGC is applied. The default AGC

settings vary depending on camera model.

BACK

EXIT

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

Note: The maximum slow shutter that the system will achieve is 1/2 second shutter (refer to

Low Light Limit on page 40).

BACK

EXIT

ADVANCED SETTINGS

SHUTTER SPEED

AGC LIMIT

AUTO IRIS

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

SENSOR SCAN MODE

FIELD ALIGN

E. IMAGE STABILIZER

IMAGE ENHANCEMENT

LOW LUX NOISE REDUCTION

WIDE DYNAMIC RANGE

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTO IRIS

SPECTRA IV

LANGUAGE

Auto iris is the lens function that automatically opens and closes the iris in response to changing

light conditions.

ACK ALERT*

Program the auto iris to operate automatically or at a user-defined level.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

OFF: Auto iris is disabled, and control is always manual.

AUTO (default): The iris is adjusted automatically to produce a constant video output as

determined by the auto iris level setting.

EXIT

If auto iris is in the auto mode, it will remain that way until the iris is manually opened or closed.

The dome will return to auto mode when it is panned or tilted more than 15 degrees.

DOME SETTINGS

<ZONES>

<AUX>

Auto Iris Level

Auto iris level is the numeric value the auto iris uses to maintain the brightness level of the

camera. Increase the value to brighten the scene. Decrease the value to darken the scene.

This setting can be adjusted if the video level in the auto iris mode is too bright or too dark.

<ALERT>*

Note: If backlight compensation is ON, decrease the auto iris level setting.

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

Auto Iris Peak

Increasing the peak value will cause the auto iris circuit to react more to highlights or “peaks” in

the picture. Decreasing this value will cause it to use the average video level to adjust the iris.

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

BACK

EXIT

ADVANCED SETTINGS

SHUTTER SPEED

AGC LIMIT

AUTO IRIS

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

SENSOR SCAN MODE

FIELD ALIGN

E. IMAGE STABILIZER

IMAGE ENHANCEMENT

LOW LUX NOISE REDUCTION

WIDE DYNAMIC RANGE

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTO SHARPNESS

Auto sharpness enhances picture detail by increasing the aperture gain of the camera and

sharpening the edges in the picture.

SPECTRA IV

LANGUAGE

ACK ALERT*

There are two settings:

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

ON (default): The camera automatically maintains a normal sharpness mode.

OFF: The sharpness of the picture is set manually by programming the sharpness level.

Sharpness level settings range from 0–63.

EXIT

DOME SETTINGS

AUTO WHITE BALANCE

This feature automatically processes the viewed image to retain color balance over a color

temperature range. The default setting for auto white balance is ON.

<ZONES>

<AUX>

R GAIN: Adjusts the picture output in the red range. As you change the value, you will see the

color change on your monitor.

B GAIN: Adjusts the picture output in the blue range. As you change the value, you will see the

color change on your monitor.

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

BACK

EXIT

ADVANCED SETTINGS

SHUTTER SPEED

AGC LIMIT

AUTO IRIS

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

SENSOR SCAN MODE

FIELD ALIGN

E. IMAGE STABILIZER

IMAGE ENHANCEMENT

LOW LUX NOISE REDUCTION

WIDE DYNAMIC RANGE

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

BACKLIGHT COMPENSATION (BLC)

SPECTRA IV

LANGUAGE

If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette.

Backlight compensation enhances objects in the center of the picture. The dome uses the center

of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash

out to white. The camera will adjust the iris so that the object in the sensitive area is properly

exposed.

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

There are two backlight compensation settings:

OFF (default): Backlight compensation is not activated.

ON: Backlight compensation is activated.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

If backlight compensation is ON, decrease the auto iris level setting and adjust the auto IR level

to a darker setting. Refer to Auto Iris Level on page 43 and Auto IR Level section on page 41.

VIDEO LEVEL

Set the video output to one of the following options:

NORMAL: 1.0 Vp-p.

HIGH (default setting): 1.2 Vp-p. to compensate for losses in video cable.

BACK

EXIT

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

BACK

EXIT

ADVANCED SETTINGS

SHUTTER SPEED

AGC LIMIT

AUTO IRIS

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

SENSOR SCAN MODE

FIELD ALIGN

E. IMAGE STABILIZER

IMAGE ENHANCEMENT

LOW LUX NOISE REDUCTION

WIDE DYNAMIC RANGE

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

SENSOR SCAN MODE

(Applies only to 35X models.)

SPECTRA IV

LANGUAGE

ACK ALERT*

Sensor scan mode controls the internal processing of the camera's image sensor. The data

scanned from the image sensor at each field time is used for the internal image control

algorithms and digital signal processing (DSP).

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

Note: When changing from PROGRESSIVE to INTERLACED, or vice-versa, the camera restarts to

establish the new setting.

EXIT

There are two sensor scan modes:

DOME SETTINGS

PROGRESSIVE (default): Produces a higher quality image by using each line scanned from the

<ZONES>

<AUX>

image sensor.

INTERLACED: Produces a slight increase in sensitivity by using blended data from pairs of lines

scanned from the image sensor.

When sensor scan mode is set to INTERLACED, the wide dynamic range and image enhancement

features are automatically disabled. There may be additional effects, such as a degradation of

the signal-to-noise ratio, degradation of the color reproduction, and a loss of motion detection for

presets configured with motion detection.

<ALERT>*

<CLEAR>

<CLOCK>

FIELD ALIGN

(Applies only to 18X, 23X, and 35X models.)

<EVENT>

BACK

EXIT

Field align determines whether the camera produces progressive segmented frame output (PsF)

or interlaced frame output. Analog video from the camera is always output in separate fields as

required for compatibility. This feature allows PsF to be recombined by an encoding device

without a time difference between fields, as is typically seen from interlaced analog video

output. Enabling field align requires that the encoding device you are using always combines the

odd and even fields in the specified order.

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

There are three field alignment settings:

BACK

EXIT

OFF (default): Field alignment is disabled. Use this setting if you are using an analog device/

system or a digital encoder that does not support PsF.

ODD: Arranges the odd field for a particular video frame before the even field for that frame.

EVEN: Arranges the even field for a particular video frame before the odd field for that frame.

Notes:

ADVANCED SETTINGS

SHUTTER SPEED

AGC LIMIT

AUTO IRIS

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

• If you enable field alignment by selecting ODD or EVEN, you must disable any deinterlacing

settings for the encoding device to achieve maximum resolution.

B GAIN

• The ODD and EVEN settings require that the sensor scan mode is set to PROGRESSIVE. If field

align is set to ODD or EVEN, the sensor scan mode automatically changes to PROGRESSIVE.

BACKLIGHT COMP

VIDEO LEVEL

SENSOR SCAN MODE

FIELD ALIGN

E. IMAGE STABILIZER

IMAGE ENHANCEMENT

LOW LUX NOISE REDUCTION

WIDE DYNAMIC RANGE

BACK

EXIT

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

ELECTRONIC IMAGE STABILIZATION

SPECTRA IV

LANGUAGE

(Applies only to 35X models.)

ACK ALERT*

Electronic image stabilization is a feature of the camera that can compensate for some forms of

external influences. In all cases, care should be taken to make sure that any dome system is

mounted to a rigid location.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

In the event that vibration is introduced to the dome system, a user can select one of the

electronic image stabilization settings in the menu. The available settings are OFF, 5 Hz, and

10 Hz. Users should apply each of the settings to the camera to see which one best addresses

the vibration that is affecting the video quality.

DOME SETTINGS

<ZONES>

<AUX>

Electronic image stabilization will not correct for all ranges of vibration. If either of the settings

fails to eliminate the vibration seen in the video, other measures should be taken to isolate the

vibration or to seek a more rigid mounting location.

Notes:

<ALERT>*

• When electronic image stabilization is applied, digital slow shutter and wide dynamic range

are disabled. Zoom, image resolution, and viewing angle are also limited when this feature

is activated.

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

• Electronic image stabilization cannot be used while in a preset that has motion detection

activated.

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

BACK

EXIT

ADVANCED SETTINGS

SHUTTER SPEED

AGC LIMIT

AUTO IRIS

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

SENSOR SCAN MODE

FIELD ALIGN

E. IMAGE STABILIZER

IMAGE ENHANCEMENT

LOW LUX NOISE REDUCTION

WIDE DYNAMIC RANGE

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

IMAGE ENHANCEMENT

(Applies only to 35X models.)

SPECTRA IV

LANGUAGE

ACK ALERT*

The image enhancement feature improves the definition of objects, lines, or text in high contrast

areas, making them appear sharper.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

There are two image enhancement settings:

DEFAULT: Image enhancement is not activated.

ENHANCED: Image enhancement is activated.

EXIT

DOME SETTINGS

Warning: When using this feature be aware that picture noise, although unnoticeable to

the eye, will increase and may cause compression rate changes in DVRs, NVRs, and

network devices.

<ZONES>

<AUX>

LOW LUX NOISE REDUCTION

(Applies only to 18X and 23X models.)

<ALERT>*

<CLEAR>

Low lux noise reduction helps to reduce video noise in low light scenes. When enabled, low lux

noise reduction is directly affected by the AGC settings for the dome system.

<CLOCK>

<EVENT>

BACK

EXIT

The following are the low lux noise reduction settings:

ON (default): Low lux noise reduction is enabled. As the scene darkens and AGC increases, the

noise reduction effect automatically increases. As noise reduction increases, you may also notice

some afterimaging and a slight reduction in color saturation.

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

OFF: Low lux noise reduction is disabled.

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

BACK

EXIT

ADVANCED SETTINGS

SHUTTER SPEED

AGC LIMIT

AUTO IRIS

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

SENSOR SCAN MODE

FIELD ALIGN

E. IMAGE STABILIZER

IMAGE ENHANCEMENT

LOW LUX NOISE REDUCTION

WIDE DYNAMIC RANGE

BACK

EXIT

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

WIDE DYNAMIC RANGE

(Applies only to 23X and 35X models.)

SPECTRA IV

LANGUAGE

ACK ALERT*

Wide dynamic range (WDR) balances the brightest and darkest sections of a scene to produce a

picture that is better balanced in lighting and provides more detail.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

Available settings are OFF and ON; the default setting is OFF. When wide dynamic range is set to

ON the frame rate is reduced from the standard 30–15 frames per second (fps). Also, when this

setting is ON the iris will not close completely, even in manual mode.

EXIT

Note: Wide dynamic range is disabled when electronic image stabilization is set to 5 Hz or 10 Hz.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

Wide Dynamic Range ON

Wide Dynamic Range OFF

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

BACK

EXIT

ADVANCED SETTINGS

SHUTTER SPEED

AGC LIMIT

AUTO IRIS

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS

SHARPNESS LEVEL

AUTO WHITE BALANCE

R GAIN

B GAIN

BACKLIGHT COMP

VIDEO LEVEL

SENSOR SCAN MODE

FIELD ALIGN

E. IMAGE STABILIZER

IMAGE ENHANCEMENT

LOW LUX NOISE REDUCTION

WIDE DYNAMIC RANGE

BACK

EXIT

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

MOTION SETTINGS

AUTO FLIP

SPECTRA IV

LANGUAGE

When the camera tilts downward and goes just beyond the vertical position, the dome rotates

180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you

continue to hold the joystick in the down position. Once you let go of the joystick after the dome

rotates, joystick control returns to normal operation. The auto-flip feature is useful for following a

person who passes directly beneath the dome.

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

There are two auto flip modes:

EXIT

ON (default): Auto flip mode is enabled.

OFF: Auto flip mode is disabled.

DOME SETTINGS

PROPORTIONAL PAN

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the

amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower for a given

amount of joystick deflection than at wide zoom settings. This keeps the image from moving too

fast on the monitor when there is a large amount of zoom.

There are three proportional pan modes:

ON (default): Enables the proportional pan mode.

OFF: Disables proportional pan mode. The pan speed will not depend on the amount of zoom.

2X: Increases the speed of the proportional pan mode to twice that used when proportional pan

is set to ON.

BACK

EXIT

MOTION

AUTO FLIP

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

SCAN SPEED (DEG/S)

PRESET FREEZE FRAME

LIMIT STOPS

BACK

EXIT

REFERENCE INFORMATION

MANUAL LIMITS SET

SCAN LIMITS SET

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

PARK TIME

SPECTRA IV

LANGUAGE

This feature allows the dome to begin a specified operation (scan, preset, or pattern) after a

programmed time of inactivity.

ACK ALERT*

Park time can be programmed from 1–720 minutes (12 hours), or set to zero, which disables this

feature. The default setting is zero.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

Park Action

This feature will define the activity when the dome parks. The following settings are available:

NONE (default): No action.

DOME SETTINGS

AUTO SCAN: Dome starts auto scan operation.

RANDOM SCAN: Dome starts random scan operation.

FRAME SCAN: Dome starts frame scan operation.

PRESET 1: Dome goes to preset 1.

<ZONES>

<AUX>

PRESET 8: Dome goes to preset 8.

PATTERN 1: Dome runs pattern 1.

<ALERT>*

PATTERN 2: Dome runs pattern 2.

<CLEAR>

PATTERN 3: Dome runs pattern 3.

<CLOCK>

<EVENT>

PATTERN 4: Dome runs pattern 4.

BACK

EXIT

PATTERN 5: Dome runs pattern 5.

PATTERN 6: Dome runs pattern 6.

PATTERN 7: Dome runs pattern 7.

PATTERN 8: Dome runs pattern 8.

MOTION

(Only 22X, 23X, and 35X models allow PATTERN 2 through PATTERN 8.)

AUTO FLIP

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

SCAN SPEED (DEG/S)

PRESET FREEZE FRAME

LIMIT STOPS

BACK

EXIT

REFERENCE INFORMATION

MANUAL LIMITS SET

SCAN LIMITS SET

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

SCAN SPEED

SPECTRA IV

LANGUAGE

Scan speed is the degrees per second that the dome will pan when in a scan mode. Scan speed is

adjustable from 1 to 40 degrees per second through the programming menu. The default setting

is 25 degrees per second.

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

PRESET FREEZE FRAME

EXIT

This feature freezes the scene on the monitor when going to a preset. This allows for smooth

transition from one preset scene to another. Preset freeze frame also reduces bandwidth when

used with digital network systems such as PelcoNet^™and guarantees that blanked areas will not

be revealed when going to a preset.

DOME SETTINGS

There are three preset freeze frame settings:

<ZONES>

<AUX>

ON: The image on the screen freezes when a preset is called. When the dome reaches the

preset, the image is unfrozen and the preset scene is displayed.

OFF: The image is never frozen.

AUTO (default): Freeze frame is turned on automatically if window blanking is ON. If window

blanking is OFF, freeze frame is off.

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

MOTION

AUTO FLIP

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

SCAN SPEED (DEG/S)

PRESET FREEZE FRAME

LIMIT STOPS

BACK

EXIT

REFERENCE INFORMATION

MANUAL LIMITS SET

SCAN LIMITS SET

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMIT STOPS

SPECTRA IV

LANGUAGE

Limit stops are programmable stops that limit the pan range of the dome. There must be two

limits, a left and a right, to define an area.

ACK ALERT*

There are two types of limit stops:

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

MANUAL: A manual (joystick) pan operation stops when a limit stop is reached.

SCAN: The dome reverses direction during random, frame, or auto scanning when a limit stop

is reached.

EXIT

To set manual or scan stops:

1. Use the joystick to position the cursor beside SET MANUAL STOPS or SET SCAN STOPS.

2. Press Iris Open.

DOME SETTINGS

<ZONES>

<AUX>

3. Follow the directions displayed on the monitor.

Note: In order for the manual or scan stops to work, the LIMIT STOPS option must be ON.

To clear manual or scan stops:

<ALERT>*

1. Use the joystick to position the cursor beside CLEAR MANUAL STOPS or CLEAR SCAN

STOPS.

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

2. Press Iris Open.

3. Follow the directions displayed on the monitor.

MOTION

AUTO FLIP

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

SCAN SPEED (DEG/S)

PRESET FREEZE FRAME

LIMIT STOPS

BACK

EXIT

REFERENCE INFORMATION

MANUAL LIMITS SET

SCAN LIMITS SET

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

AZIMUTH ZERO

SPECTRA IV

LANGUAGE

Azimuth is the pan angle from zero to 359 degrees. Azimuth zero is the pan position you specify to

be the zero degree point. Azimuth zero is normally set to magnetic north. Once set, azimuth and

compass readings are based on the set Azimuth Zero point.

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

To program azimuth zero:

1. Use the joystick to position the cursor beside SET AZIMUTH ZERO.

2. Press Iris Open.

EXIT

3. Follow the directions displayed on the monitor.

To clear azimuth zero:

DOME SETTINGS

<ZONES>

1. Use the joystick to position the cursor beside CLEAR AZIMUTH ZERO.

2. Press Iris Open.

<AUX>

3. Follow the directions displayed on the monitor.

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

MOTION

AUTO FLIP

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

SCAN SPEED (DEG/S)

PRESET FREEZE FRAME

LIMIT STOPS

BACK

EXIT

REFERENCE INFORMATION

MANUAL LIMITS SET

SCAN LIMITS SET

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

POWER UP

POWER UP ACTION

SPECTRA IV

LANGUAGE

This setting defines a specific activity (scan, preset, pattern) to be performed in the event the

power to the dome is cycled.

ACK ALERT*

The following settings are available:

NONE: No action.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

AUTO (default): The dome resumes its prior activity or direction before the power outage.

AUTO SCAN: Dome starts auto scan operation.

RANDOM SCAN: Dome starts random scan operation.

FRAME SCAN: Dome starts frame scan operation.

PRESET 1: Dome goes to preset 1.

EXIT

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

PRESET 2: Dome goes to preset 2.

PRESET 3: Dome goes to preset 3.

PRESET 4: Dome goes to preset 4.

PRESET 5: Dome goes to preset 5.

PRESET 6: Dome goes to preset 6.

PRESET 7: Dome goes to preset 7.

PRESET 8: Dome goes to preset 8.

PATTERN 1: Dome runs pattern 1.

BACK

EXIT

PATTERN 2: Dome runs pattern 2.

PATTERN 3: Dome runs pattern 3.

PATTERN 4: Dome runs pattern 4.

PATTERN 5: Dome runs pattern 5.

POWER UP

PATTERN 6: Dome runs pattern 6.

POWER UP ACTION

PATTERN 7: Dome runs pattern 7.

BACK

EXIT

PATTERN 8: Dome runs pattern 8.

(Only 22X, 23X, and 35X models allow PATTERN 2 through PATTERN 8.)

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

LINE SYNC

Line sync refers to a programmable function that allows you to synchronize all cameras within a

matrix system.

SPECTRA IV

LANGUAGE

Spectra IV and Spectra IV SE dome systems automatically sense V-Sync input. No line sync setup

is required for Pelco control systems that provide a V-Sync signal.

ACK ALERT*

For matrix systems that do not output V-Sync, there are two settings for line synchronization:

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

ON (default): Adjusts the phase of the line sync to synchronize input power. Line sync phase

settings range from zero to 359 degrees.

EXIT

OFF: The dome synchronizes to the internal clock.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

LINE SYNC

LINE SYNC PHASE

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

PRESETS

The model of the back box you are using limits the number of programmable presets that can be stored and retrieved in the

back box memory. If you are using an older model back box, you may program and use up to the maximum number of

presets available to the dome drive. However, if the dome drive is changed, the back box model will limit the number of

stored presets available to the new dome drive. Refer to the table below for more information.

Back Box Series

Model

Number of Stored Presets

Spectra

Spectra SE

Spectra III

Spectra IV

BB53

BB4

128

256

The Spectra IV dome system, which includes 16X and 18X models, has 128 preset positions. The programmable presets

are numbered 1–32, 35–82, and 100–150.

The Spectra IV SE dome system, which includes 22X, 23X, and 35X models, has 256 preset positions. The programmable

presets are numbered 1–32, 35–82, and 100–256.

Note: The number of available presets may be limited by the head-ins, controllers, and DVRs that are connected to your

dome system.

Each of the user-definable presets can be programmed to use pan, tilt, camera settings, and motion detection.

The following presets are predefined for specific functions:

Preset

33:

Action

Flip command. Pans the dome drive 180 degrees.

34:

Pan zero command. Directs the dome drive to the factory-determined zero reference point.

83–87:

88:

89:

90–91:

92–93:

94:

Reserved.

IR filter IN (color).

IR filter OUT (black-white).

Manual limit stops.

Scan limit stops.

Reserved.

95:

96:

Select main programming menu.

Stop a scan.

97:

98:

Random scanning.

Frame scanning.

99:

Start auto scanning

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Note: For American Dynamics controllers with only 32 presets, switch SW2-1 on the dome drive

SPECTRA IV

to the ON position. When SW2-1 is ON, preset

LANGUAGE

99 becomes 32

98 becomes 31

97 becomes 30

96 becomes 29

95 becomes 28

93 becomes 26

92 becomes 25

91 becomes 24

90 becomes 23

89 becomes 22

88 becomes 21

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

If the limit stops are turned off, presets 23–26 can be used as regular presets.

Use the following steps to program a preset.

DOME SETTINGS

1. Select the preset number:

<ZONES>

<AUX>

a. Use the joystick to position the cursor beside PRESET NUMBER. Press Iris Open.

The cursor moves to the right.

b. Move the joystick up or down to view selections. Press Iris Open to enter selection.

2. Edit the preset label:

<ALERT>*

a. Use the joystick to position the cursor beside EDIT PRESET LABEL.

b. Press Iris Open. The following appears on the monitor:

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

LABEL FOR PRESET

^{PRESET NUMBER}------

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXYZ.,-/

abcdefghij

CANCEL

SPACE

BACKSPACE

PRESETS

klmnopqrst

uvwxyz*;:

PRESET NUMBER

* * * PRESET NOT DEFINED * * *

c. Use the joystick to position the cursor beside a character. Press Iris Open to enter

selection. To clear a character, position the cursor beside BACKSPACE, and then press

Iris Open.

BACK

EXIT

d. When label is completed, move the cursor to OK. Press Iris Open to return to the

Preset menu.

REFERENCE INFORMATION

AZIMUTH

ELEVATION

ZOOM RATIO

3. Edit the preset scene:

CUSTOM CAMERA SETTINGS

a. Use the joystick to position the cursor beside EDIT PRESET SCENE.

b. Press Iris Open.

c. Follow the directions displayed on the monitor.

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Edit preset camera settings:

SPECTRA IV

LANGUAGE

a. Use the joystick to position the cursor beside EDIT CAMERA SETTINGS.

ACK ALERT*

b. Press Iris Open. The EDIT CAMERA SETTINGS window appears on the monitor. Refer

to Camera on page 38 and Advanced Camera Settings on page 42 to change preset

camera settings.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

c. To edit the camera settings schedule, use the joystick to position the cursor beside

EDIT SCHEDULE. Press Iris Open.

EXIT

The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on

page 80) with the following exceptions. In the Edit Schedule menu, the event type

cannot be changed. Also, the Holiday feature cannot be accessed from the Edit

Schedule menu.

DOME SETTINGS

<ZONES>

For instructions on changing the features in the Edit Schedule menu, refer to Edit

Event on page 83.

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

Notes:

• For 23X and 35X models, there are two additional options available for the IR cut filter that are

only available when programming a preset. The additional settings are IN and OUT. If the IR cut

filter is set to IN, the preset scene will be in color. If the IR cut filter is set to OUT, the preset

scene will be in black-white.

BACK

EXIT

• You can copy camera settings from one preset to another preset. To copy camera settings do

the following:

(1) Use the joystick to position the cursor beside COPY CAMERA SETTINGS.

(2) Press Iris Open. The cursor moves to the right.

PRESETS

(3) Move the joystick up or down to view selections. Press Iris Open to enter selection.

PRESET NUMBER

* * * PRESET NOT DEFINED * * *

BACK

EXIT

REFERENCE INFORMATION

AZIMUTH

ELEVATION

ZOOM RATIO

CUSTOM CAMERA SETTINGS

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

ENABLE MOTION DETECTION

(Applies only to 23X and 35X models.)

SPECTRA IV

LANGUAGE

ACK ALERT*

The following are the settings for motion detection:

OFF (default): Motion detection is turned off (disabled).

ON: Motion detection is turned on (enabled).

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

Note: Motion detection does not work if the shutter speed is set at less than 1/60 of a second.

EXIT

EDIT DETECTION AREAS

(Applies only to 23X and 35X models.)

DOME SETTINGS

<ZONES>

Four motion detection areas can be defined for a preset. Use the following steps to edit motion

detection areas.

<AUX>

1. Edit detection areas 1, 2, 3, or 4:

<ALERT>*

<CLEAR>

a. Use the joystick to position the cursor beside EDIT DETECTION AREAS.

<CLOCK>

b. Press Iris Open. The EDIT DETECTION AREAS programming window appears on the

monitor.

<EVENT>

BACK

EXIT

c. Use the joystick to position the cursor beside LOCATION for DETECTION AREA 1, 2, 3,

or 4.

PRESETS

d. Press Iris Open. The cursor moves to the right next to the number 0.

PRESET NUMBER

* * * PRESET NOT DEFINED * * *

e. Move the joystick up. A blue rectangle appears in the upper left-hand corner of the

screen.

f. Use the joystick to place the blue rectangle over the desired detection area.

g. Press Iris Open to make a selection.

BACK

EXIT

REFERENCE INFORMATION

AZIMUTH

2. Set the sensitivity of the motion detection area:

ELEVATION

ZOOM RATIO

CUSTOM CAMERA SETTINGS

a. Position the cursor next to SENSITIVITY for DETECTION AREA 1, 2, 3, or 4.

b. Press Iris Open, the cursor moves to the right.

MOTION DETECTION

MOTION DETECTION ENABLED

ACTIVATE AUX

c. Use the joystick to select one of the following sensitivity levels:

HIGH: The sensitivity level is high.

MEDIUM (default): Average sensitivity.

LOW: The sensitivity level is low.

AUX TIME (SECS)

BACK

EXIT

d. Press Iris Open to make selection.

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

EDIT DETECTION AREAS

DETECTION AREA 1

LOCATION

SENSITIVITY

MEDIUM

DETECTION AREA 2

LOCATION

SENSITIVITY

MEDIUM

DETECTION AREA 3

LOCATION

SENSITIVITY

MEDIUM

DETECTION AREA 4

LOCATION

SENSITIVITY

MEDIUM

BACK

EXIT

MOTION DETECTION AREAS

Note: Motion detection is not guaranteed to catch 100 percent of activity.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

ACTIVATE AUX COMMAND

(Applies only to 23X and 35X models.)

SPECTRA IV

LANGUAGE

ACK ALERT*

Motion detection can be programmed to trigger an auxiliary command when motion is detected.

The following are the settings for ACTIVATE AUX:

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

OFF (default): Motion detection will not trigger an AUX command.

1: Triggers a command to AUX 1.

EXIT

2: Triggers a command to AUX 2.

DOME SETTINGS

AUX TIME

(Applies only to 23X and 35X models.)

<ZONES>

<AUX>

Aux time is the length of time the auxiliary will remain on after motion is detected. Available

settings for AUX TIME are 1–60 seconds.

<ALERT>*

<CLEAR>

EDIT SCHEDULE

The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80) with

the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also,

the Holiday feature cannot be accessed from the Edit Schedule menu.

<CLOCK>

<EVENT>

BACK

EXIT

For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on

page 83.

PRESETS

PRESET NUMBER

* * * PRESET NOT DEFINED * * *

BACK

EXIT

REFERENCE INFORMATION

AZIMUTH

ELEVATION

ZOOM RATIO

CUSTOM CAMERA SETTINGS

MOTION DETECTION

MOTION DETECTION ENABLED

ACTIVATE AUX

AUX TIME (SECS)

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

PATTERNS

A pattern is a memorized, repeating series of pan, tilt, zoom, and preset functions that can be

recalled with a command from a controller or automatically by a programmed function (alarm,

park, event, or power-up).

SPECTRA IV

LANGUAGE

ACK ALERT*

Both 16X and 18X models have one user-defined pattern available. The 22X, 23X, and 35X models

can handle up to eight patterns. Pattern length is based upon memory usage rather than a fixed

amount of time. The complexity of a pattern will determine the amount of storage available to

program other patterns.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

Note: In most cases, the memory available will allow for ample time to schedule typical

patterns. If the scheduled patterns are unusually lengthy or complex, there is a possibility that

there may not be enough remaining memory to program all eight patterns for the 22X, 23X, and

35X models.

DOME SETTINGS

To program a pattern:

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

1. Use the joystick to position the cursor beside PATTERN NUMBER. Press Iris Open.

The cursor moves to the right.

2. Move the joystick up or down to view selections. Press Iris Open to enter selection.

3. Use the joystick to position the cursor beside PROGRAM PATTERN.

4. Press Iris Open. The Patterns programming window appears on the monitor.

5. Follow the directions displayed on the monitor.

After a pattern is programmed, the remaining storage percentage is displayed on the screen.

This is the amount of memory available to program the remaining patterns.

BACK

EXIT

To clear a pattern:

1. Use the joystick to position the cursor beside CLEAR PATTERN.

2. Press Iris Open.

PATTERNS

PATTERN NUMBER

3. Follow the directions displayed on the monitor.

To edit the pattern schedule:

BACK

EXIT

The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80) with

the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also,

the Holiday feature cannot be accessed from the Edit Schedule menu.

REFERENCE INFORMATION

PATTERN USAGE

REMAINING

For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on

page 83.

Note: When programming one or more presets within a pattern, use the normal controller

commands to call a preset. Not all controllers can start all patterns. However, any of the patterns

can be automatically started with park, power-up, event, and alarm functions.

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

ZONES

A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. The

Spectra IV and Spectra IV SE dome systems are capable of eight zones, each with a 20-character

label.

SPECTRA IV

LANGUAGE

ACK ALERT*

To program a zone:

1. Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open, and the

cursor moves to the right.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

2. Move the joystick up or down to view selections. Press Iris Open to enter selection.

3. Use the joystick to position the cursor beside EDIT ZONE.

EXIT

4. Press Iris Open. The Zone programming window appears on the monitor.

5. Follow the directions displayed on the monitor. After the left and right limit stops are set,

the Zones menu reappears with the ZONE ENABLED option set to YES.

DOME SETTINGS

<ZONES>

To edit a zone label:

1. Use the joystick to position the cursor beside EDIT ZONE LABEL.

2. Press Iris Open. The following information appears on the monitor:

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

LABEL FOR ZONE

^{ZONE NUMBER}------

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXYZ.,-/

abcdefghij

CANCEL

SPACE

BACKSPACE

klmnopqrst

uvwxyz*;:

BACK

EXIT

3. Use the joystick to position the cursor beside a character. Press Iris Open to enter selection.

To clear a character, position the cursor beside BACKSPACE, and then press Iris Open.

ZONES

ZONE NUMBER

* * * ZONE NOT DEFINED * * *

4. When the label is completed, move the cursor to OK. Press Iris Open to return to the Zones

menu.

ZONE ENABLED

ZONE BLANKING

To disable a zone (a zone is enabled automatically when it is programmed) or to blank a zone:

1. Move the cursor beside ZONE ENABLED or ZONE BLANKING.

2. Press Iris Open. The cursor moves to the right.

BACK

EXIT

3. Move the joystick up or down to view selections. Press Iris Open to enter selection.

To clear a zone:

1. Use the joystick to position the cursor beside CLEAR ZONE.

2. Press Iris Open. Follow the instructions on the screen.

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

WINDOW BLANKING

Window blanking allows a user to program four-sided areas that cannot be viewed by the

operator of the dome system. A blanked area will move with pan and tilt functions and

automatically adjust in size as the lens zooms telephoto and wide.

SPECTRA IV

LANGUAGE

ACK ALERT*

The 16X and 18X models have one user-defined window blank available. The 22X, 23X, and 35X

models have eight available user-defined window blanks.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

Spectra IV and Spectra IV SE dome systems have two styles of window blanking: Gray and Smear.

If the style is set to Gray, the blanked area is covered with a solid gray window. If Smear is

selected images behind the window will be noticeable but not distinguishable.

EXIT

To set a window blanking area:

DOME SETTINGS

<ZONES>

1. Use the joystick to position the cursor beside WINDOW BLANKING. Press Iris Open.

The WINDOW BLANKING menu appears on the screen.

2. Move the joystick to position the cursor beside SET WINDOWS. Press Iris Open to enter.

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

3. Position the cursor beside WINDOW NUMBER. Press Iris Open. The cursor moves to the

right.

4. Move the joystick up or down to view selections. Press Iris Open to enter selection.

5. Use the joystick to position the cursor beside EDIT WINDOW LOCATION. Press Iris Open,

and then follow the instructions that appear on the screen. When all four corners are set,

the SET WINDOWS menu reappears, the blanked area is displayed, and the ENABLE

WINDOW option is set to YES.

WINDOW BLANKING

STYLE

Notes:

• Use the inside corner of the window selection tool as a guide

when selecting the upper left, upper right, bottom right, and

bottom left corners of the window.

BLANK ALL ABOVE

BLANK ALL BELOW

INSIDE CORNER

• Set windows are not visible when editing a new window

location.

BACK

EXIT

SET WINDOWS

WINDOW NUMBER

ENABLE WINDOW

REVERSE

CLEAR WINDOW

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

6. The blanked area can be programmed to turn on or off at a specified zoom point. To set the

zoom point:

SPECTRA IV

LANGUAGE

a. Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press

Iris Open.

ACK ALERT*

b. Zoom in to the point where you want window blanking to turn on. Press Iris Open to

set the zoom point.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

Notes:

EXIT

• Since the area is already blanked out, it may be difficult to determine when you want

window blanking to turn on. Reverse the window before setting the zoom point. When

finished reverse the window again to blank out the area.

DOME SETTINGS

<ZONES>

• Increase the size of the window if any part of the blanked area is revealed during PTZ

operations.

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

WINDOW BLANKING

STYLE

Window Blanking Disabled

Window Blanking Enabled

BLANK ALL ABOVE

BLANK ALL BELOW

EDIT SCHEDULE

The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80) with the

following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also, the

Holiday feature cannot be accessed from the Edit Schedule menu.

BACK

EXIT

For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on

page 83.

SET WINDOWS

REVERSE

WINDOW NUMBER

A blanked out area can be reversed to make it visible and the areas on both sides of it not visible.

The areas above and below the blanking area remain visible. Reversing the window a second

time will return it to its original condition.

ENABLE WINDOW

REVERSE

CLEAR WINDOW

All areas that have been set for window blanking are cleared.

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

BLANK ALL ABOVE/BLANK ALL BELOW

The Blank All Above and Blank All Below options add additional flexibility to setting up privacy areas. These settings are

ideal for applications where a complete pan location needs to be blanked.

Table C. Window Blank Settings

Blank All Above

Tilt Angle Blanked Area

Blank All Below

Tilt Angle Blanked Area

OFF

No blanking

OFF

No blanking

Horizon to 3° above horizon

Horizon to 92° below horizon

10° to 92° below horizon

20° to 92° below horizon

30° to 92° below horizon

40° to 92° below horizon

50° to 92° below horizon

60° to 92° below horizon

70° to 92° below horizon

80° to 92° below horizon

-10

-20

-30

-40

-50

-60

-70

-80

3° above horizon to 10° below horizon

3° above horizon to 20° below horizon

3° above horizon to 30° below horizon

3° above horizon to 40° below horizon

3° above horizon to 50° below horizon

3° above horizon to 60° below horizon

3° above horizon to 70° below horizon

3° above horizon to 80° below horizon

-10

-20

-30

-40

-50

-60

-70

-80

HORIZON

CAMERA

Figure 3. Window Blank Tilt Angles

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

ALARMS

SPECTRA IV

LANGUAGE

The Spectra IV SE dome systems have seven alarm inputs that can be programmed as high,

medium, or low priority. When an alarm is received, an input signal to the dome triggers the user-

defined action (go to preset, run pattern, etc.) programmed for the alarm.

ACK ALERT*

Note: Refer to the notation in step 6 for the limited alarm features available for 16X and 18X

models.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

There are three global alarm settings:

EXIT

RESUME: This mode lets the dome resume its previous activity (scan, pattern, or previous

position) after all alarms are cleared.

DOME SETTINGS

SEQUENCE: This is the time the dome will perform an alarm activity when more than one alarm

of the same priority occurs at the same time.

<ZONES>

RESET DELAY: This is the amount of time the dome considers the alarm to be active after it has

physically cleared.

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

Use the following steps to program alarm settings.

1. Use the joystick to position the cursor beside ALARM SETTINGS. Press Iris Open.

2. Select the alarm number:

a. Use the joystick to position the cursor beside ALARM NUMBER.

b. Press Iris Open. The cursor moves to the right.

c. Move the joystick up or down to view selections. Press Iris Open to enter selection.

ALARMS

RESUME

SEQUENCE (SECS)

RESET DELAY (SECS)

BACK

EXIT

ALARM SETTINGS

ALARM NUMBER

ALARM PRIORITY

ALARM ACTION

ACTIVATE AUX

ALARM CONTACT

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Select the alarm priority:

SPECTRA IV

LANGUAGE

a. Use the joystick to position the cursor beside ALARM PRIORITY.

b. Press Iris Open. The cursor moves to the right.

ACK ALERT*

c. Move the joystick up or down to view the available selections. Available settings

include HIGH, MEDIUM, and LOW (default). If multiple alarms with different priorities

are active at the same time, the dome will only go to the alarms with the highest

priority.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

d. Press Iris Open to enter selection.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

HIGH: Alarm action takes highest priority and will override manual PTZ control.

MEDIUM/LOW: Alarm action will not occur if an alarm occurs during manual pan,

tilt, and zoom control.

4. Set the alarm action:

a. Use the joystick to position the cursor beside ALARM ACTION.

b. Press Iris Open. The cursor moves to the right.

c. Move the joystick up or down to view the available selections. The following are the

settings for alarm action:

BACK

EXIT

NONE: No action when alarm is triggered.

PRESET: Dome goes to the preset that is the same as the alarm number. Preset 1 will

go to Alarm 1.

ALARMS

RESUME

SEQUENCE (SECS)

RESET DELAY (SECS)

PATTERN 1: Dome runs pattern 1 when alarm is triggered.

PATTERN 2: Dome runs pattern 2 when alarm is triggered.

PATTERN 3: Dome runs pattern 3 when alarm is triggered.

PATTERN 4: Dome runs pattern 4 when alarm is triggered.

PATTERN 5: Dome runs pattern 5 when alarm is triggered.

PATTERN 6: Dome runs pattern 6 when alarm is triggered.

PATTERN 7: Dome runs pattern 7 when alarm is triggered.

PATTERN 8: Dome runs pattern 8 when alarm is triggered.

AUTO SCAN: Dome starts auto scan operation when alarm is triggered.

RANDOM SCAN: Dome starts random scan operation when alarm is triggered.

FRAME SCAN: Dome starts frame scan operation when alarm is triggered.

BACK

EXIT

ALARM SETTINGS

ALARM NUMBER

ALARM PRIORITY

ALARM ACTION

ACTIVATE AUX

ALARM CONTACT

d. Press Iris Open to enter selection.

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Set the auxiliary to activate:

SPECTRA IV

LANGUAGE

a. Use the joystick to position the cursor beside ACTIVATE AUX.

b. Press Iris Open. The cursor moves to the right.

ACK ALERT*

c. Move the joystick up or down to view the following available selections.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

NO (default): Not activated.

EXIT

1: An alarm action will close AUX 1.

2: An alarm action will close AUX 2.

DOME SETTINGS

d. Press Iris Open to enter selection.

<ZONES>

Note: The AUX 1/AUX2 will stop when all the alarms assigned to it have cleared. If the

AUX1/AUX is set up as momentary, then it will be activated each time a new alarm is

activated.

<AUX>

6. Set the alarm contact:

<ALERT>*

a. Use the joystick to position the cursor beside ALARM CONTACT.

b. Press Iris Open. The cursor moves to the right.

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

c. Move the joystick up or down to view the following available selections.

N/O (default): Normally open.

N/C: Normally closed.

ALARMS

RESUME

SEQUENCE (SECS)

RESET DELAY (SECS)

d. Press Iris Open to enter selection.

Note: The alarm contact feature is functional and available for 16X and 18X models only if

the dome drive is installed in a Spectra III SE or Spectra IV SE back box.

BACK

EXIT

7. To edit the alarm schedule:

The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80)

with the following exceptions. In the Edit Schedule menu, the event type cannot be

changed. Also, the Holiday feature cannot be accessed from the Edit Schedule menu.

ALARM SETTINGS

ALARM NUMBER

For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on

page 83.

ALARM PRIORITY

ALARM ACTION

ACTIVATE AUX

ALARM CONTACT

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

AUX

Note: If a 16X or 18X model dome drive is installed in a Spectra III SE or Spectra IV SE back box,

the auxiliary feature is functional and available. If a 16X or 18X model is installed in a standard

Spectra III or Spectra IV back box, the auxiliary feature is not available.

SPECTRA IV

LANGUAGE

ACK ALERT*

An auxiliary output is a programmable signal from the dome back box that can trigger another

device to operate. An auxiliary output is programmable to trigger from an alarm or from a controller.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

An AUX 1 command from the controller will activate the relay in the dome and operate the device

that is connected to the relay. The output of AUX 1 can be connected to the alarm input of a

system switch to activate automatic monitor switching and recording.

EXIT

An AUX 2 command from the controller will place a ground at the output of AUX 2 to operate the

device that is connected to it.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

The following are the available AUX mode settings:

TOGGLE (default): Changes the state of the auxiliary output every time an AUX command

is received from the controller.

LATCHING: Must receive an AUX ON/AUX OFF command from the controller to turn the

auxiliary output on/off.

MOMENTARY: An AUX ON command from the controller turns the auxiliary output on for the

programmed DWELL TIME. The auxiliary output will automatically turn off when the dwell time

is finished.

EDIT SCHEDULE

BACK

EXIT

The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80) with

the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also,

the Holiday feature cannot be accessed from the Edit Schedule menu.

AUX

For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on

page 83.

AUX 1 MODE

TOGGLE

DWELL TIME (SECS)

AUX 2 MODE

DWELL TIME (SECS)

TOGGLE

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

TITLE TEXT

Title text is the label used to identify the camera viewed on the monitor. Up to 20 characters can

be used for a title.

SPECTRA IV

LANGUAGE

ACK ALERT*

To edit the title text label, do the following:

1. Use the joystick to position the cursor beside EDIT TITLE TEXT.

2. Press Iris Open. The following appears on the monitor:

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

EDIT TITLE TEXT

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXY.,-/

CANCEL

SPACE

BACKSPACE

abcdefghij

DOME SETTINGS

klmnopqrst

uvwxyz#&:*

<ZONES>

<AUX>

3. Use the joystick to position the cursor beside a character. Press Iris Open to select the

character. To clear a character, position the cursor beside BACKSPACE, and then press Iris

Open.

4. When the title is completed, move the cursor to OK. Press Iris Open to return to the Title

Text menu.

<ALERT>*

<CLEAR>

<CLOCK>

5. Enable the title text label by doing the following:

a. Move the cursor beside ENABLE TITLE TEXT.

b. Press Iris Open. The cursor moves to the right.

<EVENT>

BACK

EXIT

c. Move the joystick up or down to view the selections. Select ON and then press Iris

Open to enable the title text.

TITLE TEXT

ENABLE TITLE TEXT

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

ALERT

Note: The Alert option applies only to Pressurized Spectra IV dome systems. Spectra IV systems

SPECTRA IV

that are not pressurized will not display this menu item.

LANGUAGE

ACK ALERT

Sensors strategically placed inside the pressurized dome system continually monitor pressure,

temperature, and dew point. If internal conditions reach unacceptable levels, an alert message

appears on the screen describing the alert condition. For example, if pressure drops below 1 psig,

LOW PRESSURE is displayed on the monitor.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

The following system conditions will trigger an alert message:

EXIT

System Condition

Alert Message

Temperature is above 140°F (60°C)

Temperature is below -40°F (-40°C)

Pressure is above 13 PSIG

Pressure is below 1 PSIG

HIGH TEMPERATURE

LOW TEMPERATURE

HIGH PRESSURE

DOME SETTINGS

<ZONES>

LOW PRESSURE

The difference between the temperature and

the dew point is less than or equal to 3°C.

DEW POINT (HIGH HUMIDITY)

<AUX>

<ALERT>

<CLEAR>

<CLOCK>

<EVENT>

The alert message will be repeatedly displayed until the system controller acknowledges the

alert condition by selecting ACK ALERT in the main menu. Once acknowledged, the alert message

changes to the programmed acknowledge action (ACK ACTION). If the alert condition remains

active after a period of time, the alert message reappears on the monitor, restarting the alert

message cycle. This cycle will continue to repeat until the alert condition is resolved.

BACK

EXIT

REPEAT

This setting programs how often an alert message is repeatedly displayed until the system

controller acknowledges the alert condition. The following are the settings:

CONSTANT: The alert message is continuously displayed on the monitor until acknowledged.

ALERT

REPEAT

15 MIN: The alert message is displayed every 15 minutes for a 15-second duration until

acknowledged.

ACK ACTION

ACTIVATE AUX

RESET ALERT

30 MIN: The alert message is displayed every 30 minutes for a 15-second duration until

acknowledged.

BACK

EXIT

60 MIN: The alert message is displayed every 60 minutes for a 15-second duration until

acknowledged.

OFF: The alert message is disabled and will not be displayed on the monitor.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

ACK ACTION

SPECTRA IV

LANGUAGE

Set ACK ACTION to program the frequency at which an alert message is displayed after the alert

condition has been acknowledged. The following settings are available:

ACK ALERT

ALWAYS ON: The alert message is displayed until alert conditions are cleared.

OFF 8 HRS: The alert message is turned off for 8 hours. Message returns after 8 hours if the

alert condition persists.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

OFF 24 HRS: The alert message is turned off for 24 hours. Message returns after 24 hours if

EXIT

the alert condition persists.

OFF 48 HRS: The alert message is turned off for 48 hours. Message returns after 48 hours if the

alert condition persists.

DOME SETTINGS

<ZONES>

ACTIVATE AUX

This setting activates an auxiliary when an alert condition exists. Settings include the following

options:

<AUX>

<ALERT>

<CLEAR>

NONE (default): Not activated.

1: An alert condition will close AUX 1.

2: An alert condition will close AUX 2.

<CLOCK>

CURRENT READING

The Current Reading menu displays the existing status of temperature, pressure, and dew point

inside the dome system. An arrow displayed to the left of a menu item denotes that an alert

condition exists.

<EVENT>

BACK

EXIT

ALERT

An up arrow indicates the reading is over the threshold. A down arrow indicates the reading is

below the threshold.

REPEAT

ACK ACTION

ACTIVATE AUX

RESET ALERT

The high temperature alert occurs if the temperature is above 140°F (60°C).

The low temperature alert occurs if the temperature is below -40°F (-40°C).

The high pressure alert occurs if the pressure is above 13 PSIG.

The low pressure alert occurs if the pressure is below 1 PSIG.

BACK

EXIT

The dew point (high humidity) alert occurs if the difference between the temperature and the dew

point is less than or equal to 3°C.

Note: The normal operating temperature inside the unit will be greater than the temperature

outside the back box due to the heat emitted by the system’s electronics.

CURRENT READING

TEMPERATURE

DEWPOINT

PRESSURE

REFRESH

RESET ALERT

Reset alert clears the alert condition and removes the alert label from the monitor. The system

automatically checks internal conditions 60 seconds after reset. If conditions are still unacceptable,

the alert label reappears on the screen indicating further corrective action is required.

BACK

EXIT

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEAR

Use this setting to clear user-defined settings or return the dome to factory default settings.

The following are the available settings:

SPECTRA IV

LANGUAGE

ACK ALERT*

ALL ZONES: Clears all zones. To clear a single zone, refer to Zones on page 64.

ALL PRESETS: Clears all presets. To clear a single preset, refer to Presets on page 57.

ALL PATTERNS: Clears all patterns. To clear a single pattern, refer to Patterns on page 63.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

ALL WINDOW BLANKING: Clears all blanked windows. To clear a single blanked window,

refer to Window Blanking on page 65.

EXIT

CLEAR ALL EVENTS: Clears all events. To clear a single event, refer to Event on page 80.

RESTORE FACTORY DEFAULTS: Restores all camera settings to factory default settings.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

CLEAR

CLEAR ALL ZONES

CLEAR ALL PRESETS

CLEAR ALL PATTERNS

CLEAR ALL WINDOW BLANKING

CLEAR ALL EVENTS

RESTORE FACTORY DEFAULTS

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

PASSWORD

Spectra IV and Spectra IV SE feature password protection to prevent unauthorized changes to the

dome settings. An operator can open the System Information and Display Setup menus, but

cannot access any of the dome settings menus.

SPECTRA IV

LANGUAGE

ACK ALERT*

Controller/keyboard commands cannot override password-protected settings. If a keyboard is

used to set a preset, pattern, or zone, the Enter Password menu appears on the monitor.

The password must be entered before programming can continue.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

At least one character must be entered to create a valid password.

EXIT

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

PASSWORD

ENABLE PASSWORD

BACK

EXIT

EDIT THE PASSWORD

----------

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXYZ.,-/

CANCEL

SPACE

BACKSPACE

abcdefghij

klmnopqrst

uvwxyz*;:

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

CLOCK

The clock is used to program the current date and time. The date and time set in the Clock menu

is used to program events. The date and time can also be displayed on the monitor when the

menus are not being accessed.

SPECTRA IV

LANGUAGE

ACK ALERT*

To program the clock, do the following:

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

1. Use the joystick to position the cursor beside TIME BASE. Press Iris Open. The following are

the settings for time base:

EXIT

POWER LINE: This is the most accurate time base and is the preferred selection in areas

with a stable power line frequency.

INTERNAL CLOCK: The internal clock should be used in areas where the power line

frequency is not accurate.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

a. Move the joystick up or down to view the selections.

b. Press Iris Open to select INTERNAL CLOCK or POWER LINE.

2. Use the joystick to position the cursor beside TIME FORMAT. Press Iris Open. Move the

joystick up or down to view the selections. Select 12 HOUR or 24 HOUR, and then press Iris

Open to confirm the time format.

3. Use the joystick to position the cursor beside SET TIME. Press Iris Open. Scroll through the

hours until the desired time appears. Use the joystick to move the cursor to the right. Scroll

through the minutes until the desired time appears. Press Iris Open to select the time.

BACK

EXIT

4. Use the joystick to position the cursor beside DATE FORMAT. Press Iris Open. Move the

joystick up or down to select MM/DD/YYYY or DD/MM/YYYY. Press Iris Open to confirm

the date format.

CLOCK

5. Use the joystick to position the cursor beside SET DATE. Press Iris Open. Scroll through the

TIME BASE

TIME FORMAT

SET TIME

days, months, and years until the desired number appears. Press Iris Open to select the

date.

DATE FORMAT

SET DATE

6. Use the joystick to position the cursor beside DAYLIGHT SAVINGS. Press Iris Open.

The following are the settings for daylight savings:

DAYLIGHT SAVINGS

BACK

EXIT

OFF: Daylight saving time will be turned off.

FIXED DATE: Daylight saving time occurs on the same date each year.

RELATIVE DATE: Daylight saving time occurs on a different date each year, such as the

first Sunday in April.

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

7. If FIXED DATE was selected, the following appears on the monitor:

CLOCK

TIME BASE

TIME FORMAT

SET TIME

INTERNAL CLOCK

12 HOUR

00:00 AM

DATE FORMAT

SET DATE

MM/DD/YYYY

00/00/0000

DAYLIGHT SAVINGS

TIME SHIFT

START DATE

MONTH

FIXED DATE

1 HOUR

APRIL

02:00 AM

DAY

START TIME

END DATE

MONTH

DAY

OCTOBER

02:00 AM

END TIME

BACK

EXIT

a. Use the joystick to position the cursor beside TIME SHIFT. Press Iris Open. Scroll through the options until the

desired selection appears. Press Iris Open to select the time shift.

b. Use the joystick to position the cursor beside the start date MONTH. Press Iris Open. Scroll through the options

until the desired month appears. Press Iris Open to select the month.

c. Use the joystick to position the cursor beside the start date DAY. Press Iris Open. Scroll through the options until

the desired date appears. Press Iris Open to select the day.

d. Use the joystick to position the cursor beside START TIME. Press Iris Open. Scroll through the hours until the

desired time appears. Use the joystick to move the cursor to the right. Scroll through the minutes until the

desired time appears. Press Iris Open to select the start time.

e. Repeat steps b–d for the ending date and time.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

8. If RELATIVE DATE was selected, the following appears on the monitor:

CLOCK

TIME BASE

TIME FORMAT

SET TIME

INTERNAL CLOCK

12 HOUR

00:00 AM

DATE FORMAT

SET DATE

MM/DD/YYYY

00/00/0000

DAYLIGHT SAVINGS RELATIVE DATE

TIME SHIFT

START DATE

MONTH

1 HOUR

APRIL

1ST

SUNDAY

02:00 AM

WEEK

DAY

START TIME

END DATE

MONTH

WEEK

OCTOBER

LAST

SUNDAY

02:00 AM

DAY

END TIME

BACK

EXIT

Follow the instructions in step 7 for FIXED DATE, adding WEEK.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

EVENT

An event is a preprogrammed camera, park, scan, preset, pattern, window blanking, alarm, or

auxiliary function that can be performed automatically at a specific date and time.

SPECTRA IV

LANGUAGE

ACK ALERT*

For example, suppose a camera is set to run in a continuous pattern that scans a parking lot

during business hours Monday through Friday. On Saturday and Sunday the camera needs to stop

running the pattern and observe a gate. First, program a preset to set the camera to observe the

gate. Second, schedule an event to activate the preset on the weekends. Finally, a second,

separate event must be scheduled to end the first event and allow the camera to return to the

pattern on Monday.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

Note: Events do not have a selectable duration. A second event must be scheduled to end a

previous event.

DOME SETTINGS

Events can be programmed from the Preset, Pattern, Window Blanking, Alarm, or Aux menus, or

they can be programmed from the Event menu. Events are managed individually or as a group

from the Event menu.

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

EVENT TYPE

SPECTRA IV

LANGUAGE

Any of the available event types can be selected from this menu, or you may select ALL EVENTS

to manage the events as a group.The following are the settings for event type:

ACK ALERT*

SCAN: A scan event executes a specified scan (random, auto, or frame scan) using the limit

stops and scan speed defined in the Motion menu. Refer to Motion Settings on page 50.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

PARK: A park event executes the user-defined park action as specified in the Motion menu.

Refer to Park Action on page 51.

EXIT

WINDOW BLANKING: A window blanking event activates or deactivates a previously defined

window blank. The window blank remains activated or deactivated until another programmed

event changes the state of the window or you modify it through the Window Blanking menu.

Refer to Window Blanking on page 65.

DOME SETTINGS

<ZONES>

<AUX>

AUX: An auxiliary event turns on/off an auxiliary output when the event triggers. Refer to Aux on

page 71.

ALARM: An alarm event executes the action associated with the specified alarm number. Refer

to Alarms on page 68.

PATTERN: A pattern event starts a previously defined pattern when the event is triggered. Refer

to Patterns on page 63.

<ALERT>*

CAMERA: A camera event assigns the camera settings of a preset to the current camera

settings located in the Camera menu. Refer to Camera on page 38. The preset that is referenced

by the event must be defined prior to setting up a camera event.

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

For the camera event to function, the referenced preset must have Custom Camera Settings

activated. Refer to Presets on page 57.

Note: If you have camera settings defined in the Camera menu that you wish to restore

following a camera event which overwrites those settings, you must save the original settings as

a separate preset prior to the camera event being triggered. You can then set a second camera

event to call the preset that has the original settings saved. Camera settings can also be changed

manually from the Camera menu following the original camera event.

EVENT

EVENT TYPE

EVENT LABEL

PRESET: A preset event executes a previously defined preset when the event is triggered. Refer

to Presets on page 57.

HOLIDAY

Note: The event type cannot be changed if you are accessing it through the Edit Schedule option

from the Preset, Pattern, Window Blanking, Alarm, or Aux menu.

BACK

EXIT

REFERENCE INFORMATION

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

EVENT LABEL

Set the event label to NEW to create a new event.

SPECTRA IV

LANGUAGE

ACK ALERT*

Use the following steps to manage an existing event.

1. Use the joystick to position the cursor beside EVENT LABEL. Press Iris Open.

2. Move the joystick up or down to scroll through the events. Press Iris Open to enter selection.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

As you scroll through the events, the reference information at the bottom of the screen

displays the corresponding details for each event. To view a list of all events and their

details, refer to List Event on page 84.

DOME SETTINGS

<ZONES>

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

EVENT LABEL

After an event is programmed, the label can be changed using the following steps:

1. Use the joystick to position the cursor beside EDIT EVENT LABEL.

2. Press Iris Open. The following appears on the monitor:

EDIT EVENT LABEL

EVENT 1

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXY.,-/

abcdefghij

CANCEL

BACK

EXIT

SPACE

BACKSPACE

klmnopqrst

uvwxyz#&:*

EVENT

3. Use the joystick to position the cursor beside a character. Press Iris Open to enter the

selection. To clear a character, position the cursor beside BACKSPACE, and then press Iris

Open.

EVENT TYPE

EVENT LABEL

4. When the label is completed, move the cursor to OK. Press Iris Open to return to the Edit

Schedule menu.

HOLIDAY

After an event is labeled, the label will be displayed when the event is activated according to the

display setup values for this label. Refer to Display Setup on page 36 for instructions on how to

change the way a label is displayed on the monitor.

BACK

EXIT

REFERENCE INFORMATION

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

EDIT EVENT

Use the following steps to edit an event.

SPECTRA IV

LANGUAGE

ACK ALERT*

1. Use the joystick to position the cursor beside EDIT EVENT.

2. Press Iris Open. The following appears on the monitor:

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EDIT EVENT

EXIT

EVENT LABEL

EVENT 1

EVENT ACTIVE

EVENT TIME

EVENT OCCURS

SUNDAY

12:00 AM

OFF

DOME SETTINGS

MONDAY

OFF

TUESDAY

OFF

<ZONES>

<AUX>

WEDNESDAY

THURSDAY

FRIDAY

OFF

SATURDAY

HOLIDAY

OFF

SKIP HOLIDAYS

EVENT TYPE

NUMBER

PRESET

BACK

EXIT

<ALERT>*

<CLEAR>

<CLOCK>

a. Use the joystick to position the cursor beside EVENT ACTIVE. Press Iris Open. Scroll

to select NO to leave the event inactive or YES to activate the event. Press Iris Open to

confirm your selection.

<EVENT>

BACK

EXIT

b. Use the joystick to position the cursor beside EVENT TIME. Press Iris Open. Scroll

through the hours until the desired time appears. Use the joystick to move the cursor

to the right. Scroll through the minutes until the desired time appears. Press Iris Open

to select the time.

EVENT

EVENT TYPE

EVENT LABEL

c. Use the joystick to position the cursor beside SUNDAY. Press Iris Open. The available

options are OFF and ON. Press Iris Open to confirm your selection.

d. Follow the instructions in the previous step for the remaining days of the week.

HOLIDAY

e. Use the joystick to position the cursor beside HOLIDAY. Press Iris Open. The following

are the holiday settings:

BACK

EXIT

SKIP HOLIDAYS: The event will not occur on a day of the week for which it is set if

that date is in the list of holidays.

REFERENCE INFORMATION

ON: The event will activate on holidays that are set in the Event menu, in addition to

its normally scheduled days of the week.

OFF: The event only occurs on the days of the week that it is scheduled; holidays have

no effect on the event.

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEAR EVENT

To clear an event:

SPECTRA IV

LANGUAGE

ACK ALERT*

1. Use the joystick to position the cursor beside CLEAR EVENT.

2. Press Iris Open.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

3. Follow the directions displayed on the monitor.

EXIT

LIST EVENT

To list events:

DOME SETTINGS

1. Use the joystick to position the cursor beside LIST EVENT.

2. Press Iris Open.

<ZONES>

3. All programmed events will be listed.

<AUX>

<ALERT>*

<CLEAR>

HOLIDAY

Use the following steps to create a new holiday.

<CLOCK>

<EVENT>

1. Use the joystick to position the cursor beside HOLIDAY. Press Iris Open.

BACK

EXIT

2. Move the joystick up or down to scroll through the options. If no holidays were created in

the past, NEW is the only selectable option. Press Iris Open to select NEW.

3. Proceed to Edit Holiday on page 85.

EVENT

Use the following steps to manage an existing holiday.

1. Use the joystick to position the cursor beside HOLIDAY. Press Iris Open.

EVENT TYPE

EVENT LABEL

2. Move the joystick up or down to scroll through the holidays. Press Iris Open to enter a

selection.

HOLIDAY

3. Proceed to Edit Holiday on page 85.

Note: Holidays cannot be changed through the Edit Schedule option from the Preset, Pattern,

Window Blanking, Alarm, or Aux menus.

BACK

EXIT

REFERENCE INFORMATION

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

EDIT HOLIDAY

Use the following steps to edit a holiday:

SPECTRA IV

LANGUAGE

ACK ALERT*

1. Use the joystick to position the cursor beside EDIT EVENT LABEL.

2. Press Iris Open.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

3. Use the joystick to position the cursor beside OCCURRENCE. Press Iris Open. The following

are the settings for Occurrence:

EXIT

FIXED DATE: The holiday occurs on the same date each year.

RELATIVE DATE: The holiday occurs on a different date each year, such as the third

Sunday in April.

DOME SETTINGS

<ZONES>

<AUX>

4. If FIXED DATE was selected as the occurrence, the following appears on the monitor:

EDIT HOLIDAY

OCCURRENCE

MONTH

DAY

FIXED DATE

JANUARY

BACK

EXIT

<ALERT>*

<CLEAR>

<CLOCK>

a. Use the joystick to position the cursor beside MONTH. Press Iris Open. Scroll through

the options until the desired month appears. Press Iris Open to select the month.

<EVENT>

BACK

EXIT

b. Use the joystick to position the cursor beside DAY. Press Iris Open. Scroll through the

options until the desired date appears. Press Iris Open to select the day.

5. If RELATIVE DATE was selected as the occurrence, the following appears on the monitor:

EVENT

EVENT TYPE

a. Use the joystick to position the cursor beside MONTH. Press Iris Open. Scroll through

the options until the desired month appears. Press Iris Open to select the month.

EVENT LABEL

b. Use the joystick to position the cursor beside WEEK. Press Iris Open. Scroll through

the options until the desired week appears. Press Iris Open to select the week.

HOLIDAY

c. Use the joystick to position the cursor beside DAY. Press Iris Open. Scroll through the

options until the desired day of the week appears. Press Iris Open to select the day.

BACK

EXIT

REFERENCE INFORMATION

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEAR HOLIDAY

To clear a holiday:

SPECTRA IV

LANGUAGE

ACK ALERT*

1. Use the joystick to position the cursor beside CLEAR HOLIDAY.

2. Press Iris Open.

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

3. Follow the directions displayed on the monitor.

EXIT

LIST HOLIDAYS

To list events:

DOME SETTINGS

1. Use the joystick to position the cursor beside LIST HOLIDAYS.

2. Press Iris Open.

<ZONES>

3. All programmed holidays will be listed.

<AUX>

<ALERT>*

<CLEAR>

<CLOCK>

<EVENT>

BACK

EXIT

EVENT

EVENT TYPE

EVENT LABEL

HOLIDAY

BACK

EXIT

REFERENCE INFORMATION

*This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

SCHEDULED EVENTS

Use this page to record scheduled events.

EVENT NUMBER

Example:

EVENT TYPE

LABEL

TIME

OCCURS

HOLIDAY

Preset

Weekend

11:00 AM

Sat–Sun

Skips Holidays

Description: Camera focuses on gate on weekends when the office is closed.

_______________________________________________________________________________________

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Reset, Cycle Power, Reboot

RESET CAMERA

Use this function to reset all camera settings to factory default parameters.

SPECTRA IV

LANGUAGE

ENGLISH

ACK ALERT*

CYCLE CAMERA POWER

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

If the camera is not operating or if you lose camera control, cycle camera power. Cycling camera

power resets the camera but does not change any saved camera settings.

EXIT

REBOOT SYSTEM

Reboot the system if it is not operating or if there is no control. Rebooting the system will cycle

dome and camera power without changing programmed dome settings.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Software/Language File Upload

The RJ-45 data port of the dome drive allows access for on-site setup, testing, and uploading of revised operating

software and language files. A Pelco field service tool is required to perform these operations. Field service tools include

Pelco’s remote monitor kit (IPS-RMK), remote data port box (IPS-RDPE-2), and remote monitor cable (IPS-CABLE).

For instructions on how to upload revised operating software and language files refer to the Installation/Operation manual

supplied with the field service tool.

Note: Only perform software uploads when necessary. Software uploads do not need to be performed if the dome system

is operating properly.

During a software/language file upload, a progress bar will appear on the monitor to indicate data is being transferred to

the Spectra dome system. The default setting for data transmission is 115.2 KB per second. Noisy and long-run

connections will slow the transmission rate.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Suggested Preventative Maintenance

The Spectra IV and Spectra IV SE dome systems do not require any special maintenance.

Occasionally, dust may build up on the inside or the outside of the dome. If this occurs, turn power off to the unit and

remove the lower dome from the back box. Remove the dust from the lower dome using compressed air from a spray can.

Replace the lower dome following the installation instructions that were shipped with it.

Warning: Proper eye protection should be worn when using compressed air cans.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

16X MODELS

DD4TC16

Signal Format

NTSC

Scanning System

Image Sensor

Effective Pixels

Horizontal Resolution

Lens

Zoom Speed (optical range)

Horizontal Angle of View

Focus

Maximum Sensitivity at 35 IRE

Sync System

2:1 Interlace

1/4-inch interline transfer CCD

768 (H) X 494 (V)

>470 TV lines

f/1.4 (focal length, 4~64 mm; 16X optical zoom, 8X digital zoom)

1.9/3.6/6.0 seconds

43° at 4 mm wide zoom; 3° at 64 mm telephoto zoom

Automatic with manual override

0.05 lux at 1/2 sec. shutter speed (color)

AC line lock, phase adjustable using remote control, V-Sync

Automatic (electronic iris)/manual; 1/2 ~ 1/30,000

Automatic iris control with manual override

Automatic with manual override

1 Vp-p, 75 ohms

Shutter Speed

Iris Control

Gain Control

Video Output

Video Signal-to-Noise

>50 dB

DD4TC16-X

Signal Format

PAL

Scanning System

Image Sensor

Effective Pixels

Horizontal Resolution

Lens

Zoom Speed (optical range)

Horizontal Angle of View

Focus

Maximum Sensitivity at 35 IRE

Sync System

2:1 Interlace

1/4-inch interline transfer CCD

752 (H) X 582 (V)

>460 TV lines

f/1.4 (focal length, 4~64 mm; 16X optical zoom, 8X digital zoom)

1.9/3.6/6.0 seconds

43° at 4 mm wide zoom; 3° at 64 mm telephoto zoom

Automatic with manual override

0.05 lux at 1/1.5 sec. shutter speed (color)

AC line lock, phase adjustable using remote control, V-Sync

Automatic (electronic iris)/manual; 1/1.5~1/30,000

Automatic iris control with manual override

Automatic with manual override

1 Vp-p, 75 ohms

Shutter Speed

Iris Control

Gain Control

Video Output

Video Signal-to-Noise

>50 dB

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

18X MODELS

DD4CBW18

Signal Format

NTSC

Scanning System

Image Sensor

Effective Pixels

2:1 Interlace

1/4-inch progressive scan CCD

768 (H) X 494 (V)

Horizontal Resolution

Lens

Zoom Speed (optical range)

Horizontal Angle of View

Focus

540 TV lines

f/1.6 (focal length, 3.8~68.4 mm; 18X optical zoom, 12X digital zoom)

2.9/4.2/5.8 seconds

51° at 3.8 mm wide zoom; 3° at 68.4 mm telephoto zoom

Automatic with manual override

Maximum Sensitivity at 35 IRE

0.025 lux at 1/2 sec. shutter speed (color)

0.1 lux at 1/60 sec. shutter speed (B-W)

0.004 lux at 1/2 sec. shutter speed (B-W)

Sync System

Internal/AC line lock, phase adjustable using remote control, V-Sync

Automatic with manual override

Automatic (electronic iris)/manual; 1/2~1/30,000

Automatic iris control with manual override

Automatic/off

White Balance

Shutter Speed

Iris Control

Gain Control

Video Output

Video Signal-to-Noise

1 Vp-p, 75 ohms

>50 dB

DD4CBW18-X

Signal Format

PAL

Scanning System

Image Sensor

Effective Pixels

2:1 Interlace

1/4-inch progressive scan CCD

752 (H) X 582 (V)

Horizontal Resolution

Lens

Zoom Speed (optical range)

Horizontal Angle of View

Focus

540 TV lines

f/1.6 (focal length, 3.8~68.4 mm; 18X optical zoom, 12X digital zoom)

2.9/4.2/5.8 seconds

51° at 3.8 mm wide zoom; 3° at 68.4 mm telephoto zoom

Automatic with manual override

Maximum Sensitivity at 35 IRE

0.025 lux at 1/1.5 sec. shutter speed (color)

0.1 lux at 1/50 sec. shutter speed (B-W)

0.004 lux at 1/1.5 sec. shutter speed (B-W)

Sync System

Internal/AC line lock, phase adjustable using remote control, V-Sync

Automatic with manual override

Automatic (electronic iris)/manual; 1/1.5~1/30,000

Automatic iris control with manual override

Automatic/off

White Balance

Shutter Speed

Iris Control

Gain Control

Video Output

Video Signal-to-Noise

1 Vp-p, 75 ohms

>50 dB

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

22X MODELS

DD4C22

Signal Format

NTSC

Scanning System

Image Sensor

2:1 Interlace

1/4-inch CCD

Effective Pixels

Horizontal Resolution

Lens

Zoom Speed (optical range)

Horizontal Angle of View

Focus

Maximum Sensitivity at 35 IRE

Sync System

White Balance

768 (H) X 494 (V)

>470 TV lines

f/1.6 (focal length, 4~88 mm; 22X optical zoom, 12X digital zoom)

2.4/3.9/6.3 seconds

47° at 4 mm wide zoom; 2.2° at 88 mm telephoto zoom

Automatic with manual override

0.02 lux at 1/2 sec. shutter speed

Internal/AC line lock, phase adjustable using remote control, V-Sync

Automatic with manual override

Automatic (electronic iris)/manual; 1/2~1/30,000

Automatic iris control with manual override

Automatic/off

Shutter Speed

Iris Control

Gain Control

Video Output

1 Vp-p, 75 ohms

Video Signal-to-Noise

>50 dB

DD4C22-X

Signal Format

PAL

Scanning System

Image Sensor

2:1 Interlace

1/4-inch CCD

Effective Pixels

Horizontal Resolution

Lens

Zoom Speed (optical range)

Horizontal Angle of View

Focus

Maximum Sensitivity at 35 IRE

Sync System

White Balance

752 (H) X 582 (V)

>460 TV lines

f/1.6 (focal length, 4~88 mm; 22X optical zoom, 12X digital zoom)

2.4/3.9/6.3 seconds

47° at 4 mm wide zoom; 2.2° at 88 mm telephoto zoom

Automatic with manual override

0.02 lux at 1/1.5 sec. shutter speed

Internal/AC line lock, phase adjustable using remote control, V-Sync

Automatic with manual override

Automatic (electronic iris)/manual; 1/1.5~1/30,000

Automatic iris control with manual override

Automatic/off

Shutter Speed

Iris Control

Gain Control

Video Output

1 Vp-p, 75 ohms

Video Signal-to-Noise

>50 dB

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

23X MODELS

DD4CBW23

Signal Format

NTSC

Scanning System

Image Sensor

Effective Pixels

2:1 Interlace

1/4-inch progressive scan CCD

768 (H) X 494 (V)

Horizontal Resolution

Lens

Zoom Speed (optical range)

Horizontal Angle of View

Focus

540 TV lines

f/1.6 (focal length, 3.6~82.8 mm; 23X optical zoom, 12X digital zoom)

2.9/4.2/5.8 seconds

54° at 3.6 mm wide zoom; 2.5° at 82.8 mm telephoto zoom

Automatic with manual override

Maximum Sensitivity at 35 IRE

0.025 lux at 1/2 sec. shutter speed (color)

0.1 lux at 1/60 sec. shutter speed (B-W)

0.004 lux at 1/2 sec. shutter speed (B-W)

Sync System

Internal/AC line lock, phase adjustable using remote control, V-Sync

White Balance

Shutter Speed

Iris Control

Automatic with manual override

Automatic (electronic iris)/manual; 1/2~1/30,000

Automatic iris control with manual override

Gain Control

Video Output

Video Signal-to-Noise

Wide Dynamic Range

Automatic/off

1 Vp-p, 75 ohms

>50 dB

80X

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

DD4CBW23-X

Signal Format

PAL

Scanning System

Image Sensor

Effective Pixels

Horizontal Resolution

Lens

2:1 Interlace

1/4-inch progressive scan CCD

752 (H) X 582 (V)

540 TV lines

f/1.6 (focal length, 3.6~82.8 mm; 23X optical zoom, 12X digital zoom)

2.9/4.2/5.8 seconds

Zoom Speed

Horizontal Angle of View

Focus

54° at 3.6 mm wide zoom; 2.5° at 82.8 mm telephoto zoom

Automatic with manual override

Maximum Sensitivity at 35 IRE

0.025 lux at 1/1.5 sec. shutter speed (color)

0.1 lux at 1/50 sec. shutter speed (B-W)

0.004 lux at 1/1.5 sec. shutter speed (B-W)

Sync System

Internal/AC line lock, phase adjustable using remote control, V-Sync

White Balance

Shutter Speed

Iris Control

Automatic with manual override

Automatic (electronic iris)/manual; 1/1.5~1/30,000

Automatic iris control with manual override

Gain Control

Video Output

Video Signal-to-Noise

Wide Dynamic Range

Automatic/off

1 Vp-p, 75 ohms

>50 dB

80X

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

35X MODELS

DD4CBW35

Signal Format

NTSC

Scanning System

Image Sensor

2:1 Interlace/1:1 Progressive (user-selectable)

1/4-inch CCD

Effective Pixels

768 (H) X 494 (V)

Horizontal Resolution

Lens

Zoom Speed (optical range)

Horizontal Angle of View

Focus

>540 TV lines

f/1.4 (focal length, 3.4~119 mm; 35X optical zoom, 12X digital zoom)

3.2/4.6/6.6 seconds

55.8° at 3.4 mm wide zoom; 1.7° at 119 mm telephoto zoom

Automatic with manual override

Maximum Sensitivity at 35 IRE

0.55 lux at 1/60 sec. shutter speed (color)

0.063 lux at 1/4 sec. shutter speed (color)

0.00018 lux at 1/2 sec. shutter speed (B-W)

Sync System

Internal/AC line lock, phase adjustable using remote control, V-Sync

White Balance

Shutter Speed

Iris Control

Automatic with manual override

Automatic (electronic iris)/manual; 1/2~1/30,000

Automatic iris control with manual override

Gain Control

Video Output

Video Signal-to-Noise

Wide Dynamic Range

Automatic/off

1 Vp-p, 75 ohms

>46–50 dB

128X

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

DD4CBW35-X

Signal Format

PAL

Scanning System

Image Sensor

2:1 Interlace/1:1 Progressive (user-selectable)

1/4-inch CCD

Effective Pixels

Horizontal Resolution

Lens

752 (H) X 582 (V)

>540 TV lines

f/1.4 (focal length, 3.4~119 mm; 35X optical zoom, 12X digital zoom)

3.2/4.6/6.6 seconds

Zoom Speed

Horizontal Angle of View

Focus

55.8° at 3.4 mm wide zoom; 1.7° at 119 mm telephoto zoom

Automatic with manual override

Maximum Sensitivity at 35 IRE

0.50 lux at 1/50 sec. shutter speed (color)

0.062 lux at 1/3 sec. shutter speed (color)

0.00014 lux at 1/1.5 sec. shutter speed (B-W)

Sync System

Internal/AC line lock, phase adjustable using remote control, V-Sync

White Balance

Shutter Speed

Iris Control

Automatic with manual override

Automatic (electronic iris)/manual; 1/1.5~1/30,000

Automatic iris control with manual override

Gain Control

Video Output

Video Signal-to-Noise

Wide Dynamic Range

Automatic/off

1 Vp-p, 75 ohms

>46–50 dB

128X

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the

European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures

for recycling this equipment.

C3412M-D (12/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in

material or workmanship for a period of one year after the date of shipment.

Pelco will warrant all replacement parts and repairs for 90 days from the date of

Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid

to a Pelco designated location. Repairs made necessary by reason of misuse,

alteration, normal wear, or accident are not covered under this warranty.

Exceptions to this warranty are as noted below:

•

Five years:

Pelco assumes no risk and shall be subject to no liability for damages or loss

resulting from the specific use or application made of the Products. Pelco’s

liability for any claim, whether based on breach of contract, negligence,

infringement of any rights of any party or product liability, relating to the

Products shall not exceed the price paid by the Dealer to Pelco for such

Products. In no event will Pelco be liable for any special, incidental, or

consequential damages (including loss of use, loss of profit, and claims of third

parties) however caused, whether by the negligence of Pelco or otherwise.

–

Fiber optic products

TW3000 Series unshielded twisted pair (UTP) transmission products

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models

Three years:

–

Pelco-branded fixed camera models (CCC1390H Series, C10DN Series,

C10CH Series, and IP3701H Series)

–

EH1500 Series enclosures

The above warranty provides the Dealer with specific legal rights. The Dealer

may also have additional rights, which are subject to variation from state to

state.

Spectra^®IV products (including Spectra IV IP)

Camclosure^®Series (IS, ICS, IP) integrated camera systems

DX Series digital video recorders, DVR5100 Series digital video

recorders, Digital Sentry^®Series hardware products, DVX Series digital

video recorders, and NVR300 Series network video recorders

Endura^®Series distributed network-based video products

Genex^®Series products (multiplexers, server, and keyboard)

PMCL200/300/400 Series LCD monitors

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100

or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the

following information:

–

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

•

Two years:

If there is a dispute regarding the warranty of a product that does not fall

–

Standard motorized or fixed focal length lenses

DF5/DF8 Series fixed dome products

Legacy^®Series integrated positioning systems

Spectra III^™, Spectra Mini, Spectra Mini IP, Esprit^®, ExSite^®, and PS20

scanners, including when used in continuous motion applications.

Esprit Ti and TI2500 Series thermal imaging products

Esprit and WW5700 Series window wiper (excluding wiper blades).

CM6700/CM6800/CM9700 Series matrix

Digital Light Processing (DLP^®) displays (except lamp and color wheel).

The lamp and color wheel will be covered for a period of 90 days. The

air filter is not covered under warranty.

Intelli-M^®eIDC controllers

under the warranty conditions stated above, please include

explanation with the product when returned.

written

Method of return shipment shall be the same or equal to the method by which

the item was received by Pelco.

–

RETURNS

To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100

or (559) 292-1981 to obtain an authorization number (CA number if returned for

credit, and RA number if returned for repair) and designated return location.

–

All merchandise returned for credit may be subject to a 20 percent restocking

and refurbishing charge.

•

One year:

Video cassette recorders (VCRs), except video heads. Video heads will

be covered for a period of six months.

Six months:

All pan and tilts, scanners, or preset lenses used in continuous motion

applications (preset scan, tour, and auto scan modes).

–

Goods returned for repair or credit should be clearly identified with the

assigned CA or RA number and freight should be prepaid

–

11-11-08

REVISION HISTORY

Manual #

C3412M

Date

9/06

Comments

Original version.

C3412M-A

C3412M-B

10/06

6/07

Upgraded 23X to Spectra IV SE and added 18X information. Corrected specifications. Revised SW2 Switches 4–5 section.

Corrected menus and Specifications. Added cross references. Added information about low light focus, event labels, and image

enhancement features.

C3412M-C

C3412M-D

11/07

12/08

Updated manual to reflect software version 1.070. Added DIP switch and progressive scan sections. Revised switch settings, type of

lighting, IR cut filter, and proportional pan settings.

Updated to reflect software version 1.090. Added new sections for sure focus, event types, low lux noise reduction, sensor scan mode,

and field align. Revised information regarding SW2-3, type of lighting settings, 18X and 23X specifications, auto white balance defaults,

and limitations to presets. Removed all references to 22X black-white models.

Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.

Spectra III is a trademark of Pelco, Inc.

DLP is a registered trademark of Texas Instruments Incorporated.

Vicon is a registered trademark of Vicon Industries, Inc.

Download from Www.Somanuals.com. All Manuals Search And Download.

www.pelco.com

Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA

USA & Canada Tel (800) 289-9100 Fax (800) 289-9150

International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Computer Monitor 10PM User Manual
Peerless Industries TV Mount ST632 User Manual
Pelco Satellite Radio FR85081 User Manual
Philips Car Video System 170V9 User Manual
Philips Computer Drive FM02SW00 00 User Manual
Philips Microphone SBCM D110 User Manual
Philips MP3 Player AJL700 User Manual
Pioneer DVD Player DVR 320 S User Manual
PLUS Vision Projector U5 232 User Manual
PYLE Audio Car Satellite TV System PLRD195IF User Manual