P
C
X
-
V
1
2
True
diversity
i
i
VHF
wireless
i l
receiver
i
O P E R A T I N G G U I D E
Download from Www.Somanuals.com. All Manuals Search And Download.
Intended to alert the user to the presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
Intended to alert the user of the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
CAUTION: Risk of electrical shock — DO NOT OPEN!
CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable
parts inside. Refer servicing to qualified service personnel.
WARNING: To prevent electrical shock or fire hazard, do not expose this appliance to rain
or moisture. Before using this appliance, read the operating guide for further warnings.
Este símbolo tiene el propósito, de alertar al usuario de la presencia de “(voltaje)
peligroso” sin aislamiento dentro de la caja del producto y que puede tener una
magnitud suficiente como para constituir riesgo de descarga eléctrica.
Este símbolo tiene el propósito de alertar al usario de la presencia de instruccones
importantes sobre la operación y mantenimiento en la información que viene con el
producto.
PRECAUCION: Riesgo de descarga eléctrica ¡NO ABRIR!
PRECAUCION: Para disminuír el riesgo de descarga eléctrica, no abra la cubierta. No
hay piezas útiles dentro. Deje todo mantenimiento en manos del personal técnico cualifi-
cado.
ADVERTENCIA: Para evitar descargas eléctricas o peligro de incendio, no deje expuesto
a la lluvia o humedad este aparato Antes de usar este aparato, Iea más advertencias en
la guía de operación.
Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur la présence
d’une tension dangereuse pouvant être d’amplitude suffisante pour constituer un
risque de choc électrique.
Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur qu’il ou qu’elle
trouvera d’importantes instructions concernant l’utilisation et l’entretien de l’appareil
dans le paragraphe signalé.
ATTENTION: Risques de choc électrique — NE PAS OUVRIR!
ATTENTION: Afin de réduire le risque de choc électrique, ne pas enlever le couvercle. Il
ne se trouve à l’intérieur aucune pièce pouvant être reparée par l’utilisateur. Confiez
I’entretien et la réparation de l’appareil à un réparateur Peavey agréé.
AVERTISSEMENT: Afin de prévenir les risques de décharge électrique ou de feu,
n’exposez pas cet appareil à la pluie ou à l’humidité. Avant d’utiliser cet appareil, lisez
attentivement les avertissements supplémentaires de ce manuel.
Dieses Symbol soll den Anwender vor unisolierten gefährlichen Spannungen inner-
halb des Gehäuses warnen, die von Ausreichender Stärke sind, um einen elek-
trischen Schlag verursachen zu können.
Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der
Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des
Produkts betreffen.
VORSICHT: Risiko — Elektrischer Schlag! Nicht öffnen!
VORSICHT: Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die
Abdeckung enfernen. Es befinden sich keine Teile darin, die vom Anwender repariert
werden könnten. Reparaturen nur von qualifiziertem Fachpersonal durchführen lassen.
ACHTUNG: Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte dieses
Gerät nicht dem Regen oder Feuchtigkeit ausgesetzt werden. Vor Inbetriebnahme
unbedingt die Bedienungsanleitung lesen.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank you for selecting a Peavey Pro Comm PCX-
V12 quartz controlled single channel true diversity wireless
microphone system. Before operating and installing this
system please read this instruction manual carefully and
thoroughly in order to attain the correct operating
procedures and to achieve the best results.
True Diversity Receiver
The Peavey Pro Comm PCX-V12 quartz controlled
receiver is a true diversity wireless system. This system is
also equipped with “Superior frequency tracking and muting
techniques” that is effective in eliminating the random noise
interference when the receiver is in standby state. The
Peavey Pro Comm PCX-V12 receiver is equipped with both
balanced and unbalanced outputs.
This system includes the following accessories:
•
•
•
•
AC/DC Adapter
Mic Clip
Antenna (2)
Instruction Manual
1.
UNIT FEATURES AND FUNCTIONS
A. Front Panel
1
2
3
4
5
6
Figure 1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
Antenna Input Connector A
Power Switch and Indicator:
When the switch is turned on the red indicator
illuminates to denote normal power status.
3.
4.
5.
RF Signal Level Indicator:
Indicates the RF signal strength received from the
microphone. As soon as the signal is emitted from
the microphone the LED indicator illuminates.
Audio Signal Level Indicator:
Indicates the audio signal level. As soon as the
microphone signal is modulated, the LED indicator
illuminates.
Volume Control:
Adjusts the AF output level of the receiver.
6.
Antenna Input Connector B
Rear Panel
B.
8
9
10
11
7
Figure 2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
DC 12V Input Jack:
Connect the 12V DC plug from the AC/DC adapter.
8.
Balanced Audio Output Jack:
XLR type connector
9.
Unbalanced Audio Output Jack:
1/4" Phone Jack
10.
Unbalanced Level Switch:
“LOW selection is for “Microphone-Level” output.
“HIGH” selection is for “Line-Out” level output.
11.
2.
Squelch Adjustment:
Adjust the squelch level to eliminate the RF noise
interference at the receiver.
INSTALLATION OF THE RECEIVER
1.
Install one of the antennas at the antenna input
connector A. Then install the other antenna at
the antenna input connector B.
2.
AC/DC Power Connection:
Figure 3
Connect the AC/DC adapter cable to the DC 12V
input jack. Then plug the adapter unit into an
appropriate AC outlet as shown in Figure 3. Caution:
Make sure the correct voltage is present at the AC
outlet as indicated on the AC/DC adapter.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Audio Output Connection:
a.
Unbalanced Level Switch Setting Position:
Make sure to match the unbalanced output
setting to the device input setting. The
incorrect setting could result in low sensitivity
level or over load distortion. Ex. (If you are
going into the “Line” input on a mixer or
amplifier then the switch should be set to the
high position. If you are going into the “Mic”
input of an amplifier or mixer then the switch
should be set to the low position.)
b.
Unbalanced Output:
Connect the 1/4" phone plug of the audio cable
into the unbalanced output connector on the
back of the receiver. Connect the other end of
the cable to the proper input of the desired
device. Make sure the unbalanced level switch
is in the proper position before applying power.
c.
Balanced Output:
Connect the male XLR connector into the
balanced output connector on the back of the
receiver. Connect the other end of the cable
into the “Mic/Balanced” input of the desired
device. The characteristics of the 3-pin XLR
connector are shown below in Figure 4.
PIN 2
GND PIN 1
PIN 3
Figure 4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
TWO 19/2-INCH UNITS RECEIVER INSTALLATION
A. Setup for single half-rack receiver
1.
Push the rack mount brackets (RM-11)
upwards until it is firmly attached to the
receiver. (Figure 5)
Figure 5
B.
Setup for dual half-rack receivers
1.
Remove the screws at the top and
bottom of the receiver where they will
be joined together. Remove one steel
plate from each receiver. Push the
receivers next to each other. Refer to
Figure 6.
2.
3.
Insert the steel plate in between the two
receivers (top and bottom). Align and
fasten the screws tightly as shown in
Figure 6.
Align and fasten the rack mount
7
Download from Www.Somanuals.com. All Manuals Search And Download.
brackets (RM-12) on the outer sides of
both receivers as shown in Figure 6.
Figure 6
After completion, it can be rackmounted
into an EIA standard rack case. Shown
in Figure 7.
4.
5.
Make sure that the system performs
correctly by placing the system away
from noise sources. Place the receiver
at least one meter above the ground
and one meter away from noise
sources. Place the microphone at least
one meter away from the receiving
antenna, as shown in Figure 8.
Figure 7
Figure 8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
OPERATION INSTRUCTIONS
1.
Turn the volume controls of the receiver and
device in use to a minimum setting before
turning on the microphone transmitter. After
the receivers power switch is set to the on
position, the power switch’s red indicator
illuminates to denote normal power status.
2.
If the SIGNAL LED indicators of the receiver
are illuminated before switching on the
microphone or transmitter, it indicates the
receiver is receiving interference signals. The
more LEDs that illuminate the more severity of
interference. This system has “Pilotone” and
“NoiseLock” dual-squelch features so noise
output will not occur. If multiple channels are
used and both SIGNAL and AUDIO LEDs
illuminate before the transmitter is turned on,
simply adjust the Squelch controls clockwise
until the AUDIO signal indicators extinguish.
(Figure 9). However, by adjusting the
squelch controls it affects the sensitivity level
of the receiver, therefore, shortening the
operating distance and decreasing the
stability.
Figure 9
Under normal circumstances, the SIGNAL
indicator lights up when a microphone or
transmitter is turned on near the receiver to
indicate the receiver is ready for normal
operation. Once sounds enter into the
3.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
microphone the AUDIO LED indicators will
illuminate according to the strength of sound
level. If the LEDs do not illuminate or sound is
not present at the output, the system is not
functioning properly and must be checked.
4.
Receiver and Amplifier Volume Adjustment:
a.
Single-channel Unbalanced Audio
Output: Switch the level switch on the
rear panel of the receiver to the left
“LOW” Position, then adjust the volume
control to twelve o’clock position.
Adjust the volume control of the
amplifier or mixer to an appropriate
sound level. The volume control is used
for fine adjustment of the microphone
sensitivity. When the knob is turned to
the twelve o’clock position the output
sensitivity level of the wireless
microphone is the same as a normal
dynamic microphone. Once the receiver
output level is appropriately adjusted,
do not adjust the volume control again.
Adjust the mixer or amplifier volume
control if the sound level needs to
increase or decrease.
b.
c.
Balanced Output: Adjust according to
the unbalanced audio output method in
the previous step. (Note: The level
switch does not effect the balanced
output.)
To obtain the same sensitivity level
when using a wireless microphone and
a wired microphone with one amplifier
or mixer connect both the receiver
output and the wired output to a “MIC-
10
Download from Www.Somanuals.com. All Manuals Search And Download.
IN” input jack of the amplifier or mixer.
Adjust the volume controls of the
amplifier or mixer to the same desired
level, then properly fine adjust the
receiver volume control to match the
same sensitivity as the wired
microphone.
d.
If the receiver output level is adjusted to
a level that is near the maximum input
level of the desired device, it will cause
saturation distortion of the device when
the receiver output level is increased
due to a increase in level by the sound
source. Conversely, S/N ratio will
decrease if the receiver volume control
is adjusted too low.
5.
Plug the cable of the mains unit into DC
socket on the receiver’s back panel. Thread
the cable through the cable grip as shown in
the figure below (Figure 10). The cable
grip prevents the connector from being pulled
off by accident.
Figure 10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Caution
1.
Since the installation of the antenna
influences the operating efficiency of
the receiver, the most important rule is
to minimize the distance as much as
possible between the receiving antenna
and the microphone for the best
reception and performance.
2.
The output voltage of the external DC
power supply should not be below 12V,
otherwise it will not work properly. If the
voltage is over 15V some components
of the receiver will be damaged due to
excessive current draw. Use a power
supply with a 1A minimum rating.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDHELD WIRELESS MICROPHONE
The Peavey Pro Comm PCX-V12 handheld wireless
microphone is a modular design. It also incorporates
“Superior frequency tracking and muting techniques” dual-
squelch to eliminate noise interference.
1.
Unit Features and Functions
1.
2.
Grille: Protects cartridge and
prevents breathing and wind
POP noises.
Housing: Upper portion that is
connected to the capsule
module. Internally it holds the
transmitter PCB and battery
compartment.
3.
Battery Status Indicator:
Indicates the power on/off and
battery status. When the
power switch is turned ON,
the red LED indicator flashes
briefly and then go out,
indicating normal battery
status. If no flash occurs, it has
either no battery or the battery
is drained or installed
incorrectly. The power led will
also warn when the battery is
weak by remaining on after
power up. A battery
replacement is then necessary.
Power On-off Switch:
Figure 11
4.
Slide the power switch to the “ON” position for
use or to the “OFF” position when not in use.
Battery Compartment:
Designed to accommodate one 9V battery.
Battery Cap: Covers battery in the battery
compartment.
5.
6.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 12
Unscrew the battery cap in a counter-
2.
BATTERY INSERTION
1.
clockwise direction.
2.
Insert a 9V battery into the battery
compartment according to the correct polarity
as shown in Figure12. The moment the
battery touches the terminals of the
compartment, the indicator will flash briefly.
This means the polarity is correct. However, if
no flash occurs, this indicates wrong insertion
or battery is dead. Please re-insert the battery
according to its correct polarity or exchange it
for a fresh battery.
3. OPERATING INSTRUCTIONS
1.
When the microphone is switched on the
indicator will flash briefly indicating normal
operation.
2.
After the microphone is switched on the RF
SIGNAL LED indicator of the receiver
illuminates. As the signal strength increases
the number of illuminated LEDs will increase.
If only the red LED illuminates this indicates
abnormal receiving status.
3.
During usage the AUDIO LED indicator of the
receiver will illuminate according to the sound
strength input to the microphone. When the
red LED is illuminated, it denotes the
maximum sound pressure level is being
reached but does not represent distortion.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
When the microphone is not in use make sure
to turn it off to extend the battery life. Remove
the battery from the battery compartment if the
microphone will not be in use for a long period
of time. If a rechargeable battery is used take
it out for a recharge as necessary.
BELT PACK TRANSMITTER
1.
Unit Features and Functions
1.
4-pin Jack Input Connector: Connects to the
Peavey Pro Comm 4-pin connector. Allow 5
different input configurations (See the five
ways of connection on an AF input connection,
page 19.)
2.
transmitting antenna
3. GT/MT
Switch: Switch
to the GT
Transmitting Antenna: 1/4 wavelength
1
2
position for
electric guitar
use ONLY. Gain
Control is
3
4
irrelevant for
“GT” mode.
Switch to the
“MT” position
for condenser
microphone,
wired micro-
phone or
5
7
6
Figure 11
Line-in use.
Gain Control
works in the “MT” mode for input sensitivity
adjustments.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Gain Control: Adjusts the input gain to an
appropriate level.
5.
Transmitter Housing: Contains the PCB and
battery.
6.
Battery Status Indicator: Indicates the power
on/off and battery status.
a.
When the power switch is turned on the
LED indicator flashes briefly, indicating
normal battery status.
b.
If the LED illumination is sustained at
either power on or during usage the
battery level is low. The old battery should
be replaced with a new one.
7.
8.
Power Switch: Switch to ON position for
operation. Switch to OFF position when not in
use.
Battery Compartment and Cover:
Accommodates one 9V battery. (Figure 14)
2. OPERATING INSTRUCTIONS
8
Figure 14
16
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
Push down on the battery cover to open the
battery compartment.
Insert a 9V battery into the battery compartment
according to the correct polarity as shown in
Figure 14. Then push up on the battery cover to close
the battery compartment.
3.
The LED indicator will flash briefly when
power is turned on to indicate normal battery
status. If no flash occurs it has either no
battery, the battery is drained or installed
incorrectly. Change accordingly.
4.
5.
4-Pin Jack: Volume can be adjusted by the
gain control. Gain control has no effect when
the switch is in the “GT” position (Guitar).
4-Pin Jack: Align and insert the 4-pin plug into
the jack accordingly and tighten it in the
clockwise direction as shown in Figure 15.
Figure15
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. AF 4-PIN INPUT CONNECTION METHODS
1.
2-Wire Electret condenser microphone Capsule
2.
3-Wire Electret condenser microphone Capsule
3.
Dynamic Microphone
4.
5.
Electric Guitar
Line-in (Impedance 8 KΩAttenuated 10 dB)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Overall: VHF PCX-V12
1.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Carrier Frequency Range: VHF Band 160~250 MHz
Oscillation Mode: Quartz-controlled
Channel: 1-channel fixed
Stability: + 0.005 % with temperature compensation
Max. Deviation: + 15 KHz with level limiting
Dynamic Range: > 110 dB
S/N Ratio: > 102 dB
T.H.D.: < 0.5 %
Squelch: “Superior frequency tracking and muting
techniques” dual-squelch
10.
Frequency Response: 60 Hz~18 KHz + 3 dB
2. Receiver: VHF PCX-V12
1.
2.
3.
4.
5.
Receiving Method: True Diversity Single Channel
Sensitivity: 15 dBuV at S/N > 80 dB
Image Rejection: > 60 dB
Spurious Rejection: > 75 dB
Audio Output: can switch between –2 dB/5 K Ω and
-12 dB/600 Ω unbalanced and balanced
Power Supply: 12~15 VDC/0.5 A
Panel: 19/2-inch, half-rack size
Dimensions (m/m): 210(L) x 175(W) x 44(H)
Weight: Approx. 0.6 Kgs
6.
7.
8.
9.
3. Transmitter: VHF PCX-V12
1.
2.
3.
4.
5.
6.
7.
8.
Mic Element: Condenser Microphone Capsule
Antenna: Built-in
RF Output: 10~50 mW (according to regulation)
Spurious: < -45 dBc
Battery: One 9-Volt Battery
Dimensions (m/m): 49 x 234(L)
Weight: 250 grams (without battery)
30-hour battery life per single alkaline
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Symptom
Distance
Possible
Cause
Possible
Solution
No AF signal
and no RF signal
Any
long
low transmitter
battery voltage
replace battery
No AF signal
and no RF signal
out of range
move transmitter
closer to receiver or
obstecles
No AF signal
but normal RF signal
any
any
any
microphone or
other input source
check input source
replace battery
Distortion with no
AF peak indication
low transmitter
battery voltage
Noise with low AF
signal and normal
RF signal
strong RFI
identify source and
eliminate, or change
frequency of wireless
microphone system
Intermittent AF signal
low RF signal
long
out of range
move transmitter and
closer to RCV
Intermittent AF and
RF signals
average
obstructions
in signal path
remove obstructions
or reposition transmitter
and/or RCV
MULITPLE SYSTEM
Symptom
Distance
Possible
Action
Cause
Distortion on two
or more systems without
any
units on same
frequency
change frequencies
Distortion on one
or more systems without
transmitter-
transmitter short
transmitter + transmitter change frequencies
intermod
Distortion on one
transmitter-
transmitter + transmitter increase transmitter
or more systems without
transmitter short
intermod
to transmitter distance
transmitter-receiver
short
transmitter +transmitter change frequencies
receiver intermod
Distortion on one or more
systems without
transmitter-receiver
short
transmitter +transmitter increase transmitter
receiver intermod
to receive distance
AF peak indication
20
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY
Effective Date: July 1, 1998
What This Warranty Covers
Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the
U.S.A. and Canada.
What This Warranty Does Not Cover
The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental,
product modification or neglect; (2) damage occurring during shipment; (3) damage caused by repair or service per-
formed by persons not authorized by Peavey; (4) products on which the serial number has been altered, defaced or
removed; (5) products not purchased from an Authorized Peavey Dealer.
Who This Warranty Protects
This Warranty protects only the original retail purchaser of the product.
How Long This Warranty Lasts
The Warranty begins on the date of purchase by the original retail purchaser. The duration of the Warranty is as fol-
lows:
Product Category
Duration
Guitars/Basses, Amplifiers, Pre-Amplifiers, Mixers, Electronic
Crossovers and Equalizers
2 years *(+ 3 years)
2 years *(+ 1 year)
3 years *(+ 2 years)
1 year *(+ 1 year)
2 years
Drums
Enclosures
Digital Effect Devices and Keyboard and MIDI Controllers
Microphones
Speaker Components (incl. speakers, baskets, drivers,
diaphragm replacement kits and passive crossovers)
and all Accessories
1 year
Tubes and Meters
90 days
[*denotes additional warranty period applicable if optional Warranty Registration Card is completed and
returned to Peavey by original retail purchaser within 90 days of purchase.]
What Peavey Will Do
We will repair or replace (at Peavey's discretion) products covered by warranty at no charge for labor or materials. If
the product or component must be shipped to Peavey for warranty service, the consumer must pay initial shipping
charges. If the repairs are covered by warranty, Peavey will pay the return shipping charges.
How To Get Warranty Service
(1) Take the defective item and your sales receipt or other proof of date of purchase to your Authorized Peavey
Dealer or Authorized Peavey Service Center.
OR
(2) Ship the defective item, prepaid, to Peavey Electronics Corporation, International Service Center, 412 Highway 11 &
80 East, Meridian, MS 39301 or Peavey Canada Ltd., 95 Shields Court, Markham, Ontario, Canada L3R 9T5. Include a
detailed description of the problem, together with a copy of your sales receipt or other proof of date of purchase as evi-
dence of warranty coverage. Also provide a complete return address.
Limitation of Implied Warranties
ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-
LAR PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you.
Exclusions of Damages
PEAVEY'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE
PRODUCT, AT PEAVEY'S OPTION. IF WE ELECT TO REPLACE THE PRODUCT, THE REPLACEMENT MAY BE A
RECONDITIONED UNIT. PEAVEY SHALL NOT BE LIABLE FOR DAMAGES BASED ON INCONVENIENCE, LOSS
OF USE, LOST PROFITS, LOST SAVINGS, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE
OF USE, OR ANY OTHER DAMAGES WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, EVEN IF
PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limi-
tation or exclusion may not apply to you.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
If you have any questions about this warranty or service received or if you need assistance in locating an Authorized
Service Center, please contact the Peavey International Service Center at (601) 483-5365 / Peavey Canada Ltd. at
(905) 475-2578.
Features and specifications subject to change without notice.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electric products, basic cautions should always be followed, including the following:
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water. For example, near or in a bathtub, swimming pool, sink, wet basement, etc.
Clean only with a damp cloth.
Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. It should not be placed flat against a
wall or placed in a built-in enclosure that will impede the flow of cooling air.
8.
9.
Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding plug. The wide blade or third prong is provided for your safety. When the pro-
vided plug does not fit into your inlet, consult an electrician for replacement of the obsolete outlet. Never break off the grounding. Write
for our free booklet “Shock Hazard and Grounding”. Connect only to a power supply of the type marked on the unit adjacent to the power
supply cord.
10.
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the
apparatus.
11. Only use attachments/accessories provided by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15. If this product is to be mounted in an equipment rack, rear support should be provided.
16. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced
hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S. Government’s
Occupational and Health Administration (OSHA) has specified the following permissible noise level exposures:
Duration Per Day In Hours
Sound Level dBA, Slow Response
8
6
90
92
4
95
3
97
2
100
102
105
110
115
1 1/2
1
1/2
1/4 or less
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors to the ear
canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure is in excess
of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons
exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while
this unit is in operation.
SAVE THESE INSTRUCTIONS!
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and specifications subject to change without notice.
Peavey Electronics Corporations • 711 A Street • Meridian
MS • 39301 • (601) 483-5365 • Fax 486-1278
©2000
Download from Www.Somanuals.com. All Manuals Search And Download.
|