Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precaution
WARNING
For your safety, the driver should not watch the TV or operate the controls while driving.
Please note that watching and operating the TV while driving are prohibited by law in
some countries. Also, while driving, keep the volume to a level at which external sounds
can be heard.
To prevent injury or fire, take the following precautions:
Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place
when jolted.
When extending the ignition, battery, or ground wire, make sure to use automotive-grade
wires or other wires with a 0.75mm͋(AWG18) to prevent wire deterioration and damage to
the wire coating.
To prevent a short circuit, never put or leave any metallic objects (such as coins or metal
tools) inside the unit and donst hold the LCD Screen panel while it is opening or closing
until it is completely opened or closed. Otherwise, the motorized mechanism will be
damaged.
If the unit starts to emit smoke or strange smells, turn off the power immediately and
consult your PYLE dealer.
Be careful not to drop the unit or subject it to strong shock. The unit may break or crack
because it contains glass parts.
CAUTION
To prevent damage to the Unit, take the following precautions:
Make sure to ground the unit to a negative 12V DC power supply.
Do not open the top or bottom covers of the unit.
Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity.
Also avoid places with too much dust or the possibility of water splashing.
When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with
the wrong rating may cause your unit to malfunction.
To prevent a short circuit when replacing a fuse, first disconnect the wiring harness.
Do not use your own screws. Use only the screws provided. If you use the wrong screw,
You could damage the unit.
Do not load 3-inch CDs in the CD slot
If you try to load a 3-inch CD with its adapter into the unit, the adapter might separate from
the CD and damage the unit.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Safety Precaution (p4)
About CDs (p5)
Introduction (p6)
1. Region Number .......................................... (p6)
2. Control Parts .............................................. (p6)
2-1. With Display Closed ............................ (p7)
2-2. With Display Opened .......................... (p8)
3. Head unit Rear Panel ................................. (p9)
4. Battery ........................................................ (p10)
5. Remote Control key ................................... (p11)
Connecting to Power & Multi Channel AV Control Unit System (P12)
1. Connecting to power system .................................................................. (p12)
1-1. Head unit
1-2. RT Box (Multi Channel AV Control Unit System) ............................ (p13)
2. Connecting to Multi Channel AV Control Unit System ........................... (p14)
3. Connecting DVD/CD Changer Control System ..................................... (p15)
4. Connecting to Multi Channel AV Control Unit System with Additional 6CH Amplifier ........ (p16)
Basic Operation (p17~18)
1.
2.
3.
4.
5.
6.
7.
8.
9.
Power ON/OFF......................................... (p17)
Opening the TFT LCD Panel
To Change Password
Closing the Monitor
Picture Control
Audio Control ........................................... (p18)
Pre Adjust (Color System) ....................... (p19)
Pre Adjust (Adjust TV System)
Pre Adjust (Adjust Radio System) ............ (p20)
10. Pre Adjust (Adjust Sound Mix)
11. Pre Adjust (Adjust Rear CCD) ................. (p22)
12. Rear Monitor
13. Auto Tilt System ...................................... (p23)
14. Tuning (TV-Auto Search) ........................ (p24)
15. Tuning (Radio-Auto Search)
DVD Video Player Operation (p26)
1. Changing DVD System Setting ................. (p26)
2. Basic Playback .......................................... (p27)
3. Last Memory & Others .............................. (p32)
AM/FM Radio Operation (p34)
TV Operation (p35)
Installation (p36~37)
Specifications (p38)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precaution
The marking of products using lasers (Except for some areas)
The label is attached to the chassis / case
and says that the component uses laser
beams that have been classified as Class 1. It
means that the unit is utilizing laser beams
that are of a weaker class. There is no danger
of hazardous radiation outside the unit.
CLASS 1
LASER PRODUCT
NOTE
If you experience problems during installation, consult your PYLE dealer.
If the unit fails to operate properly, press the Reset button. The unit returns to factory
setting when the Reset button is pressed. If the unit still fails to operate properly after the
Reset button has been pressed, contact your local PYLE dealer for assistance.
The illustrations of the display and the panel appearing in this manual are examples used
to explain more clearly how the controls are used. Therefore, what appears on the display
on the actual equipment, and some of the illustrations on the display may represent
something impossible in actual operation.
Lens Fogging
Right after you turn on the car heater in cold weather, dew or condensation may form on
the lens in the DVD player of the unit. Called lens fogging, CDs may be impossible to play.
In such a situation, remove the disc and wait for the condensation to evaporate. If the unit
still does not operate normally after a while, consult your PYLE dealer.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precaution
Cleaning the Faceplate terminals
If the terminals on the unit or faceplate get dirty, wipe them with a dry, soft cloth.
Cleaning the Unit
If the front panel of this unit is stained, wipe it with a dry soft cloth such as s silicon cloth. If
the front panel is stained badly, wipe the stain off with a cloth moistened with neutral
cleaner, and then wipe neutral detergent off.
Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping
the front panel with a hard cloth or using a volatile liquid such as thinner or alcohol
may scratch the surface or erases characters.
Cleaning the CD Slot
As dust tends to accumulate in the CD slot,
clean it every once in a while. Your CDs can
get scratched if you put them in a dusty CD
slot.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
About CDs
Removing CDs
Handling CDs
When removing CDs from this unit,pull
them out horizontally.
hDonst touch the recording surface of the
CD.
CDs that canst be used
hCDs that arenst round canst be used.
hCD-R and CD-RW are easier to damage
than a normal music CD. Use a CD-R or
a CD-RW after reading the caution items
on the package etc.
hDonst stick tape etc. on the CD. Also,
donst use a CD with tape stuck on it.
hCDs with coloring on the recording
surface or that are dirty canst be used.
hThis unit can only play the CDs with
When using a new CD
If the CD center hole or outside rim has
burrs, use it after removing them with a ball
- point pen etc.
It may not correctly play disks which do
not have the mark as above.
hA CD-R or CD-RW that hasnst been
finalized canst be played. (For the
finalization process, refer to your CD-
R/CD-RW writing software, and your CD-
R/CD-RW recorder instruction manual.)
CD storage
hDonst place them in direct sunlight (On
the seat or dashboard etc.) and where
the temperature is high.
hStore CDs in their cases.
CD accessories
CAUTION
Donst use disc type accessories.
With the screen open, a driver may not see
the disc insertion slot. For your safety,
insert a disc with the screen closed.
CD cleaning
Clean from the center of the disc and move
outward.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Notice. “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation
1. Region Number
The region number of this Unit is labeled on the
rear panel of the unit.
Most DVDss are manufactured specifically for
sale and use in a specific geographic region.
A discss Region Number must correspond to the
Region Number of this Unit. If the Region
Number of a disc is different from the Region
Number of the this Unit, playback will not be
possible.
This DVD Player is designed for use in Region 1 (North America).
If a disc is identified astRegion 0uit will work on any DVD Player.
2. Control Parts
2-1 With Display Closed
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
WITH THE DISPLAY CLOSED
˝ Volume Up/Down
Use this button to increase/decrease the volume.
˞ Tilt
Use this button to adjust the angle of the TFT LCD panel in 3 steps and every time this
button is pressed with being held for about 2 second or longer, the TFT LCD panel moves
backward with 2 steps & forward with 1 step.
˟ Open/Close
Use this button to Open/Close the TFT LCD Panel. Press Open button about 2
Seconds or longer and then, the TFT LCD Panel Should be horizontally held for
controlling an equipment like air conditioner in car. And it Should be returned to last
position after 10 Seconds automatically.
ˠ Reset
Use this button when the unit fails to operate properly or return to default (Initial Mode).
ˡ Joy Stick
Check all functions with UP/DOWN/LEFT/RIGHT for System menu and Press enter
key.
ˢ Remote Sensor
Remote Control infrared sensor.
ˣ Power/Mode
Use this button to turn on/off. For Turn -off, hold this button about 2 seconds or longer.
And use this button to switch the modes such as AV1,AV2, DVD, Radio,TV.
ˤ Menu/Setup/Band
- Menu: Use this button to display menu stored on DVD disc.
- Setup: Use this button to show DVD SETUP MENU with holding this button about 2
seconds or longer.
- Band: Use this button to switch receiving bands for radio (FM1, FM2, FM3, AM1,
AM2) & TV(TV1, TV2).
˥ Mute
Use this button to mute the sound.
˦ P.S/BSM
Use this button for preset scan and press again to continue receiving that station in the
radio mode. And press this button about 2 seconds for storing up FM/AM stations that
are automatically tuned in sequentially.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
˧ Track/CH Up/Down
- Use this button to tune to a station to be stored in the radio/TV mode .
1) Track up key with pressing over 2 seconds should be Radio Frequency or
TV Channel memory.
2) Track down key with pressing over 2 seconds should delete Radio Frequency
or TV Channel to be momorized.
- Use this button to select a track in audio CD, MP3.
- Use this button to select a chapter in the DVD video.
˨ Seek & Tuning Up/Down
-Radio Mode: The unit starts to seek next station.
-TV Mode: Use this button to seek TV Channel.
-Disc Mode: Hold down to perform fast-forward and fast-backward on disc.
Press and hold this button to switch the Seek/Manual Tuning Mode.
˩ Eject
Use this button to eject a disc in slot.
˪ Vol
Use this button to increase/decrease Volume.
2-2 WITH THE DISPLAY OPENED
˫ P.S/BSM
Same as ˦
≗ Track (CH) Up/Down
Use this button to select the next higher or lower preset station channel in the Radio
and TV mode. In disc mode, Track/Chapter Up/Down function will be worked by this button.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
4. BATTERY
Preparing & Using The Remote Control
BATTERY INSTALLATION
NOTICE (BATTERY)
PLEASE FOLLOW THE INSTRUCTIONS
BELOW. INCORRECT BATTERY USEAGE
MIGHT CAUSE EARLY DISCHARGE, LEAKAGE
OR CORROSION DAMAGE.
* Do not insert battery in the wrong direction.
Be sure to observe the correct polarity (+/-) as
indicated in the battery compartment.
* It is dangerous to charge/heat/open or short
circuitry the battery.
* Please remove the battery in case of not
using the remote control for a long period of
time.
* It is time to replace the battery if the remote
control does not work properly or if the
operating range becomes reduced.
* Should battery leakage occur, clean the
battery compartment with a soft cloth and
replace with a new battery.
USING THE REMOTE CONTROL
NOTICE (REMOTE CONTROL)
* The remote control should be aimed directly
towards the remote sensor of the Unit.
* Avoid dropping the remote control.
* Avoid spilling liquids on the remote control or
exposing it to extreme heat.
The remote control should be pointed at
the remote sensor in order for the Unit
Monitor to function correctly.
Distance: Maximum of 16 feet from the
front of the remote sensor.
Angle: Approximately ꢀꢁꢂ30 from center.
Please do not locate the Unit where direct
sunlight or fluorescent illumination might
shine directly at the remote sensor. This
will interfere with proper remote control
operation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
5. Remote Control Key
˝ Power/Mode
˞ Mute
˟ Open/Close
ˠ Volume Up/Down
ˡ AF/TA (RDS Function)
ˢ PTY/ REG (RDS Function)
ˣ Track (P.Seek/CH) Up/Down
ˤ Band (OSD ON/OFF)
˥ Menu
˦ Enter
˧ Set Up
˨ DVD Menu
˩ Slow Disc (Seek/Manual) Up/Down
˪ Tilt/Navi (Navigation Function)
˫ Rear Monitor
≗ NTSC/PAL(DVD ONLY)
≘ P.S/BSM
≙ Play/Pause
≚ Stop/Eject
≛ Numeric Key Pad
䟷 Repeat
䟸 A-B Repeat (Random in CD Changer)
䟹 Display (Intro in CD Changer)
䟺 Title
䟻 S-Title
䟼 Audio
䟽 Angle
䟾 Zoom
䟿 Goto
⇪ PBC
≜ Aspect, Fine Tune
≝ Clear
≞ Return
≟ ꢀ10 (3D)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Power & Multi Channel AV Control Unit System
1. Connecting to Power System
The illustration below is showing power system connection. Please also refer to the
ownerss and installation manuals supplied with the associated equipment. If it doesnst
have corrected connection, it may cause unexpected damage.
1-1. HEAD UNIT
Notice
hMake sure the connection of Parking Brake wire. If it has no connection, the unit will
not show any picture.
hConnect the Dimmer wire, otherwise its illumination on button will not be lit.
hWhen using the optional power amplifier, connect to Amplifierss power control terminal
with Power Control Wire.
hDepending on what antenna you are using, connect auto antenna wire either to the
control terminal of the motor antenna or to the power terminal for the film-type antenna.
1-2. RT BOX (Multi Channel AV Control Unit System)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Power & Multi Channel AV Control Unit System
2. RT BOX 16P CONNECTOR WIRING DIAGRAM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Power & Multi Channel AV Control Unit System
3. Connecting to Multi Channel AV Control Unit System
The Illustration below is just possible examples with our Multi Channel AV Control Unit
System only. The exact connection method will vary depending on the specific
components selected for a particular installation.
Please also refer to the ownerss and installation manuals supplied with the associated
equipment.
œ Don’t use both AV2 and DVD/VCD Changer Input at the same time because
it is linked each other. It can be used either only for AV2 or only for DVD/ VCD
Changer Input.
NOTICE
h Make sure that power is off before making signal connections.
h Connect this Unit Mi-Net output directly to the Mi-Net input of the RT BOX.
h In Case of Using Sub woofer, you must use additional Power Amplifier with Sub woofer
Line out.
WARNING
Do not use the Digital Audio Output of this Unit unless you are connecting it to a suitable
Dolby Digital and/or DTS decoder or to an amplifier equipped with a digital audio input. High
volume digital signals may damage your equipment and your hearing.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Power & Multi Channel AV Control Unit System
4. Connecting to DVD Changer Control System
œ 䤎Don’t use AV2 Audio L/R input of RT Box when DVD Changer is Connected.
䤎You can just use only AV2 Video input of RT Box from DVD Changer Video
output.
䤎In case of using CD Changer instead of DVD Changer, the AV2 of RT Box
can
not be availed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Power & Multi Channel AV Control Unit System
5. Connecting to Multi Channel AV Control Unit System with Additional 6CH Amplifier
The Illustration below is just possible examples for our Multi Channel AV Control Unit
System with Additional 6CH Amplifier. The exact connection method will vary depending
on the specific components selected for a particular installation.
Please also refer to the ownerss and installation manuals supplied with the associated
equipment.
NOTE
In case of wanting more powerful 5.1CH sound system, you have to add additional power
Amplifier of 6CH or 5CHꢀ1CH.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
POWER ON/OFF
CLOSING THE MONITOR
1. Hold the left and right upper side of the
monitor parallel with the front of the
unit as the picture below.
1. POWER ON
1) Press POWER button to turn the power
on and the monitor will be automatically
positioned vertically when the monitor is
opened.
2. You can also turn the power on by
pressing the OPEN button. The power
will be turned on and the monitor will be
opened.
2. Press OPEN button or POWER button,
and then the monitor will be closed.
2. POWER OFF
NOTE
1) Press the POWER button again to turn
the power off over 2 seconds.
1. If the left and right angle of the monitor
is not parallel to the front of the unit, the
monitor cannot be closed.
2. If the OPEN button is pressed while radio
or video is on, the monitor will close.
But the sound will stay on. Press the
POWER button to turn the sound off.
2) If you turn the power off by pressing the
POWER button with the monitor open,
the monitor will close. If the car key is
pulled out, or the OPEN button is pressed,
the monitor will automatically close.
OPENING THE TFT LCD PANEL
PICTURE CONTROL
1. Press MENU key until the monitor
displays following picture.
Press OPEN/CLOSE button or power button
and then the monitor will open.
NOTE
If the OPEN/CLOSE button is pressed
when the monitor is closed and the power
is off, the monitor will open and the power
will turn on.
2. Use §© key and place cursor (Yellowbar)
on Picture and press ENTER key.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
3. Use § © key and place cursor (Yellow
bar) on the item you want to adjust (Ex.
Contrast) and press ENTER key as
picture above.
3. Use § © key and place cursor (Yellow
bar) on the item you want to adjust
(Ex. Tone/ Volume) and press
ENTER key as picture below.
4. Press Ú Ü key to adjust the level of the
selected item as picture below.
4. Use § © key and place cursor (Yellow
bar) on the sub-item you want to adjust
(Ex. Bass) and press ENTER key as
picture below
5. Press ENTER key at least for 2 seconds
to return to the previous menu.
* When no key is pressed for 5 seconds,
the menu will disappear.
6. Do the same process as above to adjust
Brightness, Color and Tint.
7. Press ENTER key at least for 2 seconds
on current screen to return to the
previous screen. Press Menu key about
1 second to turn MENU off directly.
5. Press Ú Ü key to adjust the level of the
selected item as picture below.
AUDIO CONTROL
1. Press MENU key until the monitor
displays following picture.
6. Press ENTER key at least for 2 seconds
to return to the previous menu.
* When no key is pressed for 5 seconds,
the menu will disappear.
7. Bass/Mid/Treble can be adjusted from
ꢂ14 level to ꢀ14 level.
2. Use § © Key and place cursor (Yellow Bar)
on Audio and Press ENTER key.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
5. Press ENTER key at least for 2 seconds
on current screen to return to the previous
screen. Press Menu key about 1second
to turn MENU off directly.
6. Do the same process as above to adjust
Navigation, Auto Dimmer and Beep
Tone.
8. Do the same process as above to adjust
Volume.
9. Press ENTER key at least for 2 seconds
on current screen to return to the previous
screen. Press Menu key about 1 second
to turn MENU off directly.
7. Navigation, Auto Dimmer and Beep Tone
will be turned on and off by pressing
ENTER key.
PRE ADJUST - (COLOR SYSTEM)
1. Press MENU key until the monitor
displays following picture.
PRE ADJUST - (ADJUST TV SYSTEM)
1. Press MENU key and select Pre Adjust
until the monitor displays following picture.
2. Use § © Key and place cursor (Yellow
Bar) on Pre Adjust and press ENTER key.
2. Use § © Key and place cursor (Yellow
3. Use § © Key and place cursor (Yellow
Bar) on Color System and Press ENTER
key as picture below.
Bar) on Adjust and press ENTER key.
3. Use § © key and place cursor (Yellow
bar) on TV and press ENTER key as
picture below.
4. Each time you press ENTER key, color
system changes as below.
4. Use § © key and place cursor (Yellow
bar) on Field and Press ENTER key as
picture below.
NTSC --> PAL --> SECAM --> NTSC
* When no key is pressed for 5 seconds, the
menu will disappear.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
5. Each time you press ENTER key,
Field/Standard should be changed
at the same time as below.
4. Use § © key and place cursor (Yellow
bar) on Band and press ENTER key as
picture below.
5. Each time you press ENTER key, Band
changes as below.
U.S.A/M-->CCIR1/BG-->CCIR2/BG -->
Ireland/II’-->Australia/BG-->China/BG
-->O.I.R.T/DK-->France/BG
U.S.A / 100KHz--> Europe / 50KHz-->
O. I. R. T / 50KHz-->Asia / 50KHz-->
Australia / 100KHz -->
* When no key is pressed for 5 seconds,
the menu will disappear.
6. Press ENTER key at least for 2 seconds
on current screen to return to the
previous screen. Press Menu key about
1 second to turn MENU off directly.
PRE ADJUST - (ADJUST RADIO SYSTEM)
S.America/100KHz--> China/50KHz-->
Japan/100KHz --> Korea/100KHz
1. Press MENU key and selet Pre Adjust
until the monitor displays following
picture.
* When no key is pressed for 5 seconds,
the menu will disappear.
6. Press ENTER key at least for 2 seconds
on current screen to return to the
previous screen. Press Menu key about
1 second to turn MENU off directly
PRE ADJUST - (ADJUST SOUND MIX)
1. Press MENU key until the monitor
displays following picture.
2. Use § © Key and place cursor (Yellow
Bar) on Adjust and press ENTER key.
3. Use § © key and place cursor (Yellow
bar) on Radio and press ENTER key as
picture below.
The monitor displays following picture.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
7. Each time you press ENTER key, Center
changes as below
FRONT --> REAR --> ALL --> OFF
8. Press ENTER key at least for 2 seconds
to return to the previous screen.
9. Use § © key and place cursor (Yellow
bar) on Navigation and press ENTER key
as picture below.
2. Use § © Key and place cursor (Yellow
Bar) on Sound Mix and press ENTER
key.
3. Use § © key and place cursor (Yellow
bar) on Sub woofer and press ENTER
key as picture below.
10. Each time you press ENTER key,
Navigation changes as below.
R --> L --> L+R --> OFF
11. Press ENTER key at least for 2 seconds
to return to the previous screen.
4. Each time you press ENTER key, Sub
Woofer changes as below.
12. Use § © key and place cursor(Yellow
bar) on Hands free and press ENTER
key as picture below.
FRONT --> REAR --> ALL --> OFF
5. Press ENTER key at least for 2 seconds
to return to the previous screen.
6. Use § © key and place cursor (Yellow
bar) on Center and press ENTER key
as picture below.
13. Each time you press ENTER key,
Hands free changes as below.
R --> L --> L+R --> OFF
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
5. Press ENTER key at least for 2 seconds
to return to the previous screen.
6. Use § © key and place cursor (Yellow
bar) on Angle and press ENTER key as
picture below.
14. Press ENTER key at least 2 seconds on
current screen to return to the previous
screen. Press Menu key about 1 second
to turn MENU off directly.
*
When no key is pressed for 5 seconds,
the menu will disappear.
PRE ADJUST - (ADJUST REAR CCD-
FOR REAR VIEW CAMERA)
1 . Press MENU key and select Pre Adjust
until the monitor displays following
picture.
7. Each time you press ENTER key, Angle
changes as below.
0 deg --> 180 deg
8. Press ENTER key at least for 2 seconds
on current screen to return to the
previous screen. Press Menu key about
1 second to turn MENU off directly.
REAR MONITOR
2. Use § © Key and place cursor (Yellow
Bar) on Rear CCD and press ENTER
key.
1. Press MENU key until the monitor
displays following picture.
3. Use § © key and place cursor (Yellow
bar) on Use and press ENTER key as
picture below.
2. Use §© Key and place cursor (Yellow Bar)
on Rear Monitor and press ENTER key.
4. Each time you press ENTER key, Use
changes as below.
3. Use §© key to set Rear Monitor as
DVD or Radio or TV or AV1 or AV2 or
Off as picture below.
ON --> OFF
* When no key is pressed for 5 seconds,
the menu will disappear.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
* When no key is pressed for 5 seconds,
the menu will disappear.
AUTO TILT SYSTEM
RDS (Radio Data System)
1. Press MENU key until the monitor
displays following picture.
1. Press MENU key until the monitor
displays following picture.
2. Use § © Key and place cursor (Yellow
Bar) on Auto Tilt System and press
ENTER key.
2. Use § © Key and place cursor (Yellow
Bar) on RDS and press ENTER key.
3. Use § © Key and place cursor (Yellow)
on On and press ENTER key as picture
below.
3. Use § © key to set Auto Tilt System
as On or Off as picture below.
* When no key is pressed for 5 seconds,
the menu will disappear. Press ENTER
key at least for 2 seconds on current
screen to return to the previous screen.
Press Menu key about 1 seocnd to turn
MENU off directly.
* When no key is pressed for 5 seconds,
the menu will disappear.
4. Press PS/BSM button to receive RDS
stations as picture below.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
TUNING (TV-AUTO SEARCH)
OVERVIEW OF THE RDS FUNCTION
1. After adjust TV system(Field/Standard)
on Pre-Adjust, Press P.S/BSM to search
TV channels.
AF (Alternative Frequencies) / REG
(Regional)
When pressed short, AF switching mode
is selected and the state of AF switching
mode is displayed by AF segment in LCD.
* ‘Searching’ will be blinking as it searches
TV channels and channel number is
changing as it searches TV channels.
Segment off : AF switching mode off
Segment on : AF switching mode on : Has
RDS information.
Segment flashing : AF switching mode is
selected, but RDS information is not
received yet.
2. When Auto-Search is completed,
memorized channels will be shown on
the screen and cursor will be placed on
the first channel as below. The next
channels will be shown on the next screen
by pressing BAND button
.
When AF switching mode is selected, the
radio checks the signal strength of the AF
all the time. The interval of checking time
of each AFs depends on the signal
strength of current station, from a few
minute for strong station to a few seconds
for weak station.
TUNING (RADIO-AUTO SEARCH)
Every time that new AF is stronger than
current station, it switches over to that
frequency in short time. Because the mute
time of AF switching or checking time is
very short, it is almost inaudible in case of
normal program.
1. After adjust Radio system (Band/Freq.
Step) on Pre-Adjust, press P.S/BSM to
search RADIO channels.
* ‘Searching’ will be blinking as it searches
Radio channels and channel number is
changing as it searches RADIO channels.
When pressed long, it is activated of
regional mode on/off.
2. When Auto-Search is completed,
memorized channels will be shown on
the screen and cursor will be placed on
the first channel as below. The next
channels will be shown on the next
screen by pressing BAND button.
Regional mode on : AF switching or PI
SEEK is implemented to the station which
has all PI codes are the same as current
station. REG of individual segment is
turned on also together with displaying
"REG ON" on numeric display for a few
seconds.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
Regional mode off : The regional code in
the format of PI code is ignored when AF
switching or PI SEEK is implemented.
PTY (Program Type)
This key is operated as follows.
REG of individual segment is turned off
together with displaying "REG OFF" on
numeric display for a few seconds.
- PTY MUSIC group ---> PTY SPEECH
group ---> PTY off.
While selecting PTY engagement, its
selection is implemented by preset
buttons as described in preset key. When
PTY is selected, the radio starts to search
corresponding PTY information, and stops
if the corresponding PTY information is
detected.
When regional mode is off, the radio may
switch from a national program station to a
local variant of that program, or from a
local station in an area to a local station in
another area. So, customers can listen to a
wrong program when switched station
transmits wrong program. To avoid this
unwanted situation, REG should be on,
and then the radio will only switch to an AF
that broadcasts exactly the same program.
If corresponding PTY information is not
existed any more, PTY engaging is
automatically exit to normal mode.
TA (Traffic Announcement) / TP (Traffic
Program)
When pressed short, it is engaging
whether TA mode on or off.
When TA mode is on and a traffic
announcement is transmitted :
- When the unit was in CD mode, it will
switch temporarily to radio mode.
- If the volume level was under the
threshold point it will be raised to the
threshold point but the user changed the
volume level which was more than the
threshold point. (Min. TA volume level), it
will be set to the last level.
- When TA mode is on, TA of individual
segment is turned on.
- When a TP station is received, TP of
individual segment is turned on.
* TA interruption function
The current traffic announcement is
cancelled by pressing this key but the TA
mode will not be off.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VIDEO PLAYER OPERATION
DVD VIDEO PLAYER OPERATION
1. CHANGING DVD SYSTEM SETTING
œ About 2CH or 6CH Setup:
Press SET UP button and then, there should
be shown 5 categories as Language, Video,
Audio, More Audio and Parental.
If 2CH is set into this menu with
Analog out, it’s sound will come out by
2CH even though DVD title was set by
5.1CH Sound. To enjoy Dolby Digital
or DTS Sound with Analog out, this
menu must be set by 6CH with Dolby
Digital and DTS Category and DVD
title also has to set up by 5.1CH.
1) Language
4) More Audio
As shown above, Language for OSD can be
changed to English, French, Japanese,
Korean and Spanish.
2) Video
Dolby Prologic and Subwoofer can be
on/off in this mode.
5) Parental
In this video mode, TV Shape & TV System
can be changed.
3) Audio
This is to prohibit the playing of
specified DVDs which are unsuitable
for children. Some discs contain a
restriction level which enables parents
to remove scenes or prevent playback
of discs by children. DVD players are
equipped with a password designed to
prevent children changing the level.
There are two outputs as analog and digital
output and analog output can be changed to
2 CH (4CH output) and 6 CH (5.1CH). And
its digital output is only for additional
decoder processor.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VIDEO PLAYER OPERATION
2. BASIC PLAYBACK
Preparation
Insert a disc into the center of the insertion slot with the label side faced up. The disc plays
automatically after loading.
Note:
hNever insert foreign objects into the disc insertion slot.
hIf the disc is not inserted easily, there may be an other disc in the mechanism or the unit
may require service.
Loading 8cm discs
hNo adapter is required to play an 8cm disc.
hInsert the 8cm disc into the center of the insertion slot.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VIDEO PLAYER OPERATION
1) POWER/MODE
Use this button to turn on/off. For Turn -
off, hold this button about 2 seconds or
longer. Each time This button is pressed,
its source should be changed to AV1 ª
AV2 ª DVD ª RADIOª TV.
2) OPEN/CLOSE
Use this button to open/close the TFT
LCD Panel.
3) EJECT
Use this button to eject a disc in slot for 2
seconds or longer.
4) PLAY/PAUSE
The disc will be loaded and playback will
automatically and if it is pressed once
more during playback, it will be worked
by pause.
h If a single-sided disc is loaded upside
down, it will come out automatically in
a few seconds.
h If an Audio CD is loaded, thetCDu
indicator appears on LCD. If an MP3
CD is loaded, the “MP3” indicator
appears on LCD. If you want to change
folder, press TITLE key for 2 seconds
or longer and then select the folder you
want.
h When all chapters on the disc have
played, this unit will automatically
stop. If several titles are on the disc,
the discss menu screen will reappear.
œ How to use Remocon
To choose any function inside a circle
press Key for 1 Second and to choose one
outside a circle for at least 2 Seconds.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VIDEO PLAYER OPERATION
5) CHANGING SUBTITLE LANGUAGE (S
-TITLE)
It is possible to change the subtitle
language to a different language from the
selected one. This operation works only
with discs on which multiple subtitle
languages are recorded.
hPress S-TITLE button for 3 seconds
or longer during playback.
hPress repeatedly S-TITLE until the
desired language is selected.
hTo eliminate the On Screen Subtitle, please
press S-TITLE repeatedly to select OFF.
6) CHANGING AUDIO SOUND TRACK
LANGUAGE (AUDIO)
It is possible to change the Audio
Soundtrack Language to a different
language from the selected one at the
initial setting. This operation works only
with discs on which multiple audio sounds
are recorded.
hPress AUDIO button for 3 seconds or
longer during playback.
h%esired Audio Soundtrack Language is
selected.
7) DISPLAY
When pressing Display button for 2
seconds or longer, there shows PlayTime
status and if press it one more for
2 seconds or longer there shows all
information for title like below. In CD
Changer Mode, this button should be
operated by Intro Scan that each track
playback for 5 seconds.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VIDEO PLAYER OPERATION
Playback of the selected item will
begin.
8) REPEAT (SET UP)
To repeat viewing or listening, press
REPEAT during playback. Each time
this button is pressed, the TV Screen
changes as below.
Repeat Chapter ª Repeat Title ªShuffle
ª Off.(DVD Title) / Repeat OneªShuffle
ª Off.(Audio CD Title)
9) A-B REPEAT
Repeating sections between two
specific points (A-B repeat).
h Press A-B during playback at the point
where repeat play is to start(A).
h Press A-B during playback at the point
where repeat play is to be concluded(B).
h Repeat play of the selected section(A-B)
starts.
h To return to normal play, press A-B once,
and thentOFFuwill appear. In CD
Changer Mode, this button should be
worked by Random playback.
10) DIRECTION BUTTONS - MENU/TITLE
NAVIGATION & MOVEMENT
Press §ꢁ©ꢁÜꢁÚ and press ENTER, or
press the numeric button(s), to
select the desired item.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VIDEO PLAYER OPERATION
For further information, also refer to any
instructions that may have been packaged
with the disc you are playing.
After playback
When the unit is not in use, remove the disc
and turn off the power by pressing the
POWER button.
(Do not remove the disc if you plan to use
thetLAST MEMORYufunction explained on
the next page).
NOTES
- Ift
uappears on the screen when a
button is pressed, it means that the selected
function is not available on the disc you are
playing at that time.
- Depending on the specific DVD disc, some
operations may be different or restricted.
For this refer to the jacket or case of the
disc you are playing.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VIDEO PLAYER OPERATION
3. LAST MEMORY - PICKING UP WHERE YOU LEFT OFF & OTHERS
This unit is equipped with atLAST MEMORYu
function which lets you resume viewing of a
movie from the point where you left off. You
must press only PLAY button, not Power button
in case the power has been turned off (and
stand by power)
NOTE
The Last Memory function is not supported once
the disc is removed from the slot.
1) VOLUME UP/ DOWN
Adjust the Volume by pressing the VOLUME
ꢀꢁꢂꢃbuttons.
2) GOTO SEARCH
Press the GOTO button to move to any title
chapter or elapsed time on the disc.
hTime: Input the desired elapsed time with
the Numeric Keypad, then press the ENTER
button.
hTITLE/CHAPTER: Input the desired title
or Chapter # with the Numeric Keypad,
then press the ENTER button.
3) ZOOM
Press the ZOOM button totZoom-inu
(enlarging the picture on the screen).
Press the ZOOM button repeatedly to cycle
Zoom between < 1 < 2 < 3 < Off.
While in Zoom mode, the Direction buttons
allow you to view areas of the picture that
are not visible on the screen.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD VIDEO PLAYER OPERATION
4) ANGLE
Some DVDs may contain scenes which have
been shot simultaneously from number of
different angles. For these discs, the same
scene can be viewed from each of these
different angles using the ANGLE button.
(The recorded angles differ depending on the
disc used.)
5) SLOW DISC
Press and hold this button during playback.
Every time this button is pressed shortly, its
speed should be changed by x2, x4, x8, x20
with fast forward and fast backward. And if it
is pressed about 2 seconds and longer,
its picture will be moved by one frame.
6) DVD MENU
Press this button to show the menu of DVD
Title and choose one of menus as desired.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
AM/FM RADIO OPERATION
1. BAND (AM/FM)
Each time this button is pressed, the band will
be changed to FM1 ª FM2 ª FM3 ª AM1 ª
AM2
2. PRESET SCAN/BSM
Following your desired band selection, press
P.S/BSM button about 2 seconds or longer,
and then tuner will search until stations of
sufficient strength have been found and will
store them in sequence. The stored each
station will playback for 5 seconds in sequence
until you select one stored channel by pressing
P.S/BSM one more.
3. MANUAL (SEEK) UP/DOWN
To find out a desired station, press this button
until ‘beep’ sound is heard and then, press it
shortly in no time moving to the very station
step by step.
*After above process, at least 3 seconds is
necessary to perform below process.
If you press it shortly, tuner will seek and
playback a next station.
4. TRACK (P.SEEK/CH) UP/DOWN
Press this button to move to the stored next
station you want. In Disc mode, this button is
worked by Track Up/Down.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
TV OPERATION
1. PRESET SCAN/ BSM
Firstly, select the desired station and press the
PS/BSM button shortly. And then, Tuner will
now search until stations of sufficient strength
have been found and will store them into TFT
LCD automatically in sequence.
2. MANUAL UP/DOWN
To find out a desired TV channel, press this
button shortly.
3. TRACK (P.SEEK/CH) UP/DOWN
Press this button to move to the stored TV
channel you want.
4. FINE TUNE
Press this button for 2 seconds or longer to
have desirable Air signals on a current channel.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
PRECAUTIONS
Choose the mounting location carefully so that the unit will not interfere with the normal
driving functions of the driver. Avoid installing the unit where it would be subject to high
temperatures, such as from direct sunlight or hot air from the heater or where it would be
subject to dust, dirt or excessive vibration. Use only the supplied mounting hardware for a
safe and secure installation.
MOUNTING ANGLE ADJUSTMENT
Adjust the mounting angle to less than 20ʣ
MOUNTING EXAMPLE
Installation in the dashboard
STRAP
Be sure to use the strap to secure the back
of the unit in place. The strap can be bent
by hand to the desired angle.
HOLDER
After inserting the holder into the
dashboard, select the appropriate tabs
according to the thickness of the dashboard
material and bend them inwards to seccure
the holder in place.
HOW TO DETACH THE MOUNTING FRAME
1. Insert release keys into the slots A.
2.Remove the frame B from the unit.
NOTE.
Keep the release keys in the safe place, as
you may need it in the future to remove the
unit from the car.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Make sure that the unit is installed securely in place. If the unit is unstable, it may
malfunction. For example, the source may skip.
1. Align the holes in the unit with the vehicle mounting bracket and secure the unit with the
accessory screws.
2. During installation, do not use any screw except for these provided. The use of different
screws might result in damage to the main unit.
Damage may occur if a screwdriver or similar tool is used with excessive force during
the installations.
SUPPLIED MOUNTING KIT
˞ MACHINE SCREW
˟ MACHINE SCREW
˝ BRACKET X2
ˠ FALT WASHER
(ʡ5 X 0.5T) X 4
(M4 X 6) X4
(M5 X 6) X4
ˡ FALT WASHER
(ʡ5 X 0.5T) X 4
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
FM TUNER
LCD MONITOR
Frequency Range: 87.50 MHz to 108.0 MHz
Screen Size : 7-inch wide type
Usable Sensitivity: 9 dBf
166mm Width ƒ100mm Height
Display method:
Transmission type TN liquid crystal display
Drive method: TFT (thin-film transistor)
active matrix driving
50dB Quieting Sensitivity: 15 dBf
Alternate Channel Selectivity: 70 dB
Stereo Separation (1 kHz): 30 dB
Frequency Response (ꢀꢁꢂ3 dB): 30Hz to 15 kHz
Pixels: 336,960 (1440ƒ234)
AM TUNER
Frequency Range: 530kHz to 1710kHz
Usable Sensitivity: 25 dBuV
GENERAL
Power source voltage:
14.4VDC(10.8 to 15.6V allowable)
Ground: Negative
Current consumption: 3.0A (1W)
Auto Antenna Rated Current: 500 mA less
Dimensions of the Main Unit:
TV TUNER
Receiving Channel: VHF LOW (S3-NZ1)
VHF HIGH (E12-E5)
UHF (E69-E21)
178mm Widthƒ50mm Heightƒ159.8mm Depth
Dimensions of the Tuner Amp Unit:
166mm Widthƒ38mm Heightƒ266mm Depth
Weight of the Main Unit: 2kg
Weight of the Tuner Amp Unit: 1kg
Dimensions of the Remote Control Unit:
DVD PLAYER
System : Digital Versatile DIsc System
with CDDA capable
Usable discs : DVD video disc, Compact DISC
Frequency Response:
20Hz to 20 kHz (‚3 dB)
50.8mm Widthƒ11.4mm Heightƒ160mm Depth
Weight of the Remote Control Unit: 70g
20Hz to 20 kHz (CD) (‚3 dB)
Signal to Noise Ratio: 90 dB (1kHz) IHF-A
Dynamic Range: 90 dB (1 kHz)
Distortion: 0.05%
AUDIO AMPLIFIER
Rated power output:
18Wƒ4 (20 Hz to 20 kHz, 1%, 4ʃ)
Maximum power output: 200W (50Wƒ4)
Speaker impedance: 4ʃ (4 to 8ʃ)
INPUT
Audio input:
780‚50mVrms
(input impedance 10kʃ or greater)
Video input:
1.0‚0.2 Vp-p (input impedance 75ʃ)
NOTES
VIDEO OUTPUT
Specifications and design ard subject to
change without notice for further
improvement.
Video output:
1.0‚0.2Vp-p (output impedance 75ʃ)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
DO NOT HOLD THE LCD SCREEN PANEL WHILE IT IS
OPENING OR CLOSING UNTIL IT IS COMPLETELY
OPENED OR CLOSED. OTHERWISE, THE MOTORIZED
MECHANISM WILL BE DAMAGED.
s
BEFORE WORKING THE UNIT, READ THE OWNER S
MANUAL CAREFULLY AND FOLLOW UP THE
INSTRUCTIONS IN IT. ALWAYS WORK THE UNIT WITH
THE REMOTE CONTROLLER OR THE FUNCTION
BUTTONS ON THE UNIT. OTHERWISE, THE UNIT CAN
BE DAMAGED.
PRINTED IN KOREA
Download from Www.Somanuals.com. All Manuals Search And Download.
|