PLCD65WXMU
OWNER’S MANUAL
Mobile Audio System
• PLL Synthesizer Stereo Radio
• CD Player/MP3 Player/WMA Player
• Automatic Memory Storing
• Full Detachable Panel
• Preset Equalization
• Electronic Shockproof (ESP) Function
• USB Interface
• Auxiliary Input Function
• Remote Control
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Notes:
TAKE OUT SCREW BEFORE
INSTALLATION
• Choose the mounting location where
the unit will not interfere with the
normal driving function of the driver.
Before install the unit, please remove the
two screws.
Take out screw before installation
• Before finally installing the unit,
connect the wiring temporarily and
make sure it is all connected up
properly and the unit and the system
work properly.
• Use only the parts included with the
unit to ensure proper installation.
The use of unauthorized parts can
cause malfunctions.
DIN FRONT-MOUNT (Method A)
Installation Opening
This unit can be installed in any dashboard
having an opening as show below:
• Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.
• Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop,
like an emergency stop.
53 mm
182 mm
• If installation angle exceeds 30˚ from
horizontal, the unit might not give its
optimum performance.
Installing the unit
Be sure you test all connections first, and
then follow these steps to install the unit.
1. Make sure the ignition is turned off,
and then disconnect the cable from
the vehicle battery's negative (-)
terminal.
30˚
• Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
2. Disconnect the wire harness and the
antenna.
3. Press the release button on the front
panel and remove the control panel
(see the steps of “removing the front
panel”).
4. Lift the top of the outer trim ring then
pull it out to remove it.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either
from “Front” (conventional DIN Front-
mount) or “Rear” (DIN Rear-mount
installation, utilizing threaded screw holes
at the sides of the unit chassis).
For details, refer to the following
illustrated installation methods.
5. The two supplied keys release tabs
inside the unit's sleeve so you can
remove it. Insert the keys as far as they
will go (with the notches facing up) into
the appropriate slots at the middle left
and right sides of the unit. Then slide
the sleeve off the back of the unit.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
grounding of the unit.
Sleeve
L Key
Note to install the short threading
terminal of the mounting bolt to the back
of the unit and the other long threading
terminal to the dashboard.
Outer Trim Ring
Front Panel
Spring Washer
Hex Nut
Metal Strap
Mounting Bolt
Plain Washer
R Key
Tapping Screw
6. Mount the sleeve by inserting the sleeve
into the opening of the dashboard and
bend open the tabs located around the
sleeve with a screwdriver. Not all tabs
will be able to make contact, so
examine which ones will be most
effective. Bending open the appropriate
tabs behind the dashboard to secure
the sleeve in place.
10. Reconnect the cable to the vehicle
battery's negative (-) terminal. Then
replace the outer trim ring and install
the unit's front panel. (see the steps
of “installing the front panel”).
Dashboard
Tabs
Removing the unit
1. Make sure the ignition is turned off,
and then disconnect the cable from
the vehicle battery's negative (-)
terminal.
Screwdriver
2. Remove the metal strap attached the
back of the unit (if attached).
3. Press the release button to remove the
front panel.
Sleeve
4. Lift the top of the outer trim ring then
7. Reconnect the wire harness and the
antenna and be careful not to pinch
any wires or cables.
8. Slide the unit into the sleeve until it
locks into place.
pull it out to remove it.
5. Insert both of the supplied keys into
the slots at the middle left and right
sides of the unit, then pull the unit out
of the dashboard.
9. To further secure the unit, use the
supplied metal strap to secure the back
of the unit in place. Use the supplied
hardware (Hex Nut (M5mm) and Spring
Washer) to attach one end of the strap
to the mounting bolt on the back of
the unit. If necessary, bend the metal
strap to fit your vehicle's mounting
area. Then use the supplied hardware
(Tapping Screw (5x25mm) and Plain
Washer) to attach the other end of
metal strap to a solid metal part of the
vehicle under the dashboard. This strap
also helps ensure proper electrical
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
DIN REAR-MOUNT (Method B)
If your vehicle is a Nissan, Toyota, follow
these mounting instructions.
Use the screw holes marked T (Toyota),
N (Nissan) located on both sides of the
unit to fasten the unit to the factory radio
mounting brackets supplied with your
vehicle.
Side view showing
Screw Holes marked T, N
Factory Radio
Mounting
Screw
Bracket
Screw
Dashboard or
Console
To fasten the unit to the factory radio
mounting brackets.
Align the screw holes on the bracket with
the screw holes on the unit, and then
tighten the screws (5x5mm) on each side.
Note: the outer trim ring, sleeve and the
metal strap are not used for method B
installation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE DETACHABLE FRONT PANEL
REMOVING THE FRONT PANEL
1. Press the release button ( ) on the
front panel and pull off the front panel.
Precautions when handing
1. Do not drop the front panel.
2. Do not put pressure on the display or
control buttons when removing or
installing the front panel.
3. Do not touch the contacts on the front
panel or on the main unit body. It may
result in poor electrical contact.
Release Button
4. If any dirt or foreign substances
adhered on the contacts, they can be
removed with a clean and dry cloth.
Front Panel
5. Do not expose the front panel to high
temperatures or direct sunlight in
anywhere.
6. Keep away any volatile agents (e.g.
benzene, thinner, or insecticides) from
touching the surface of the front panel.
7. Do not attempt to disassemble the
front panel.
2. Keep front panel into the case.
Protective Case
Front Panel
INSTALLING THE FRONT PANEL
To install the front panel, insert the panel
into the housing and make sure the panel
is properly installed. Otherwise,
abnormality occurs on the display or some
keys will not function properly.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING CONNECTION
MAIN UNIT
ANTENNA CONNECTOR
(BLACK)
(GREY)
AUX IN CABLE
RCA CABLE
Rch RED
FUSE
RED
IGNITION
SWITCH (ACC+)
Lch WHITE
FUSE
MEMORY
BACK-UP (B+)
YELLOW
BLACK
Rch RED
GROUND (B–)
Lch WHITE
POWER
BLUE
ANTENNA
WHITE
GREY
FRONT Lch
SPEAKER
FRONT Rch
SPEAKER
WHITE/BLACK
GREEN
GREY/BLACK
VIOLET
REAR Lch
SPEAKER
REAR Rch
SPEAKER
GREEN/BLACK
VIOLET/BLACK
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LOCATION OF KEYS
17 7 18 15 10
5
8
11 9
4
24
16 13 19 6
1
20
21
22 14 23
2
3
12
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SWITCHING ON/OFF THE UNIT
Switch on the unit by pressing any button
(except button (7) and button (4)).
When system is on, press POWER button
(9) to turn off the unit.
MUTE
Press MUT button (3) to mute down the
sound instantly. If any button is pressed
in the mute state, the mute state is
released.
FACEPLATE RELEASE
Press button (7) to detach the removable
faceplate.
EQUALIZATION
Press and hold EQ/REC button (19) for
several seconds to turn on equalization
function and to select desired audio mode.
There are five kinds of mode as below:
SOUND ADJUSTMENT
Press PUSH SEL button (10) shortly to
select the desired adjustment mode.
The adjustment mode will change in
the following order:
FLAT
CLASSICS
POP M
ROCK M
DSP OFF
LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated
functions on the display (8).
VOL
BAS
TRE
BAL
FAD
(Volume)
(Bass)
(Treble)
(Balance)
(Fader)
REMOTE SENSOR
By rotating the AUDIO knob (10) clockwise
or counter-clockwise, it is possible to
adjust the desired sound quality.
Point the remote control handset to the
remote sensor IR (11). Press the function
keys on the handset to control the system.
Press and hold the SEL button (10) for
several seconds to enter into the selection
for the situation of beep sound, then rotate
the AUDIO knob (10) clockwise or
ESP FUNCTION
If the unit has the electronic shockproof
function, it can be shockproof about
several of seconds.
counter-clockwise to select as follows:
BEEP 2ND
BEEP ALL
BEEP OFF
RESET FUNCTION
RESET button (12) must be activated with
either a ballpoint pen or thin metal object.
The RESET button is to be activated for
the following reasons:
- BEEP 2’nd mode:
The beep is only generated when
all allowed double function button
is pressed long (several seconds).
e.g.
- Initial installation of the unit when all
wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
Note: If press RESET button (12), the
unit can’t work yet, please use a cotton
swab soaked in isopropyl alcohol to clean
the socket on the front panel.
When preset button is pressed.
When BND/LOU button (13) is
pressed.
When AS/PS button (18) is pressed.
- BEEP ALL mode:
The beep is generated when every key
is pressed.
RADIO OPERATION
- BEEP OFF mode:
The beep is disabled.
• SWITCHING TO RADIO MODE
Press MOD button (6) shortly to
select radio mode, the radio mode
appears in the display together with
the memory band and frequency.
LOUDNESS
Press BND/LOU button (13) for several
seconds to reinforce the bass output.
Press it for several seconds again to
release this function.
• SELECTING THE FREQUENCY
BAND
SET THE CLOCK
At radio mode, press BND/LOU button
(13) shortly to select the desired band.
The reception band will change in the
following order:
Press the DSP button (15), the clock is
shown on the display. Then hold down
the button until the clock flashes. Then
press the TUNE/TRACK button (17) to
change hours or TUNE/TRACK button
(16) to change minutes.
FM1
FM2
FM3
AM
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
• SELECTING STATION
CD OPERATION
Press TUNE/TRACK button (17) or
TUNE/TRACK button (16)
• SWITCHING TO CD MODE
If there is no CD inserted in the driver:
Gently insert the CD with the printed
side uppermost into the CD
compartment until you feel some
resistance. The CD is drawn into the
driver automatically. CD playback
begins.
shortly to activate automatic seek
function. Press for several seconds
until “MANUAL” appears on the
display, the manual tuning mode is
selected. If both buttons have not
been pressed for several seconds, they
will return to seek tuning mode and
“AUTO” appears on the display.
If a CD is already inserted in the driver:
Keep pressing MOD button (6) shortly
until the CD mode display appears.
• LOCAL/DISTANT
Press LOC button (2) to select between
local and distant stations.
Local setting for reception of strong
station, and a distant setting for
reception of weaker stations. This
function is effect during AUTO SEEK
operation.
• SELECTING TRACKS
Press TUNE/TRACK button (16) or
TUNE/TRACK button (17) to move
to the previous track or the following
track. Track number shows on display.
Hold TUNE/TRACK button (16) or
TUNE/TRACK button (17) to fast
reverse or fast forward. CD play starts
from when you release the button.
• AUTOMATIC MEMORY STORING &
PROGRAM SCANNING
- Automatic memory storing
Press AS/PS button (18) for several
seconds, the radio searches from the
current frequency and checks the
signal strength until one cycle search
is finished. And then 6 strongest
stations are stored into the
• PAUSING PLAYING
Press PAU button (20) to pause CD
player. Press it again to resume play.
• PREVIEWING ALL TRACKS
Press SCN button (21) to play first
several seconds of each track on the
current disc. Press it again to stop
intro and listen to track.
corresponding preset number button.
- Program scanning
Press AS/PS button (18) shortly to
scan preset station. When the field
strength level is more than the
threshold level of stop level, the radio
is holding at that preset number for
several seconds with release mute,
then searches again.
• REPEATING THE SAME TRACK
Press RPT button (22) to continuously
repeat the same track. Press it again
to stop repeat.
• STATION STORING
Press any one of the preset buttons (14)
(1 to 6) to select a station, which had
been stored in the memory. Press this
button for several seconds(until 2’nd
beeps come out), current station is
stored into the number button.
• PLAYING ALL TRACKS IN RANDOM
Press SHF button (23) to play all
tracks on CD in random order. Press
again to cancel the function.
• EJECTING A DISC
• MONO/STEREO
Press button (4) to stop CD playing
and eject the disc from the disc slot
(5).
Press MON button (1) to select mono
or stereo mode. You can sometimes
improve reception of distant stations
by selection mono operation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
MP3 OPERATION
=> “Searching Directory or File
Name”=> “Navigation” from root by
TUNE/TRACK UP/DOWN buttons =>
“Navigation” from current directory by
TUNE/TRACK UP/DOWN buttons.
• Searching Track Directly
Press AS/PS (D-AUD) button for
one
time. It enters into “Searching track
directly” in Digital Audio CD.
The unit searches the track selected
by following direct numeric buttons:
M1-M6, MOD (7), TUNE/TRACK
DOWN (8), TUNE/TRACK UP (9),
DSP(0).
If selected three digits, the unit
searches the track at once. If
selected one or two digits, the unit
wait for ENT (BND/LOU) button for
seconds. The unit searches the track
after few seconds, even if the enter
button is not pressed.
• Searching Directory or File Name
Press AS/PS (D-AUD) button for
two
• SWITCHING TO CD (MP3) MODE
If there is no MP3 disc inserted in the
driver:
Gently insert the MP3 disc with the
printed side uppermost into the disc
slot (5) until you feel some resistance.
The MP3 disc is drawn into the driver
automatically. The MP3 playback
begins.
If a MP3 disc is already inserted in the
driver:
Keep pressing MOD button (6) shortly
until the CD (MP3) mode display
appears.
• EJECTING A DISC
Press button (4) to stop MP3 playing
and eject the disc from the disc slot
(5).
• SELECTING TRACKS IN SINGLE
STEP
Press TUNE/TRACK button (16) or
TUNE/TRACK button (17) to move
to the previous track or the following
track. Track number shows on display.
times. It enters into “Searching
Directory or File Name” in Digital
Audio CD.
The unit searches files and
directories that have the same
character which is inputted by the
user pressing the corresponding
buttons listed on the Table 1 below.
Explain as follows:
• PAUSING PLAYING
Press PAU button (20) to pause MP3
player. Press it again to resume play.
• PREVIEWING ALL TRACKS
Press SCN button (21) to play first
several seconds of each track on the
current disc. Press again to stop intro
and listen to track.
- Use the corresponding buttons to
select the characters A to Z, blank,
0 to 9, _, -, +.
- Press SEL button to confirm entry
• REPEATING THE SAME TRACK
Press RPT button (22) to continuously
repeat the same track. Press it again
to stop repeat.
of each characters.
- Press BND/LOU (ENT) button to
start the title search.
In case the selected title is a
directory name, display will show
(‘ ‘), then
- Use the TUNE/TRACK UP/DOWN
buttons to list all songs under this
directory and select the title.
- Press BND/LOU (ENT) button to
confirm and start the play.
- Repeat the above steps if the newly
selected title is again a directory.
• PLAYING ALL TRACKS IN RANDOM
Press SHF button (23) to play all tracks
on MP3 disc in random order. Press
again to cancel the function.
• SELECTING TRACKS BY AS/PS/D-
AUD BUTTON
AS/PS button is assigned as Digital
Audio Mode selection button in MP3
operation. When pressed, it is
activated as selecting each mode of
Digital Audio. “Searching track directly”
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
• Searching From Root Directory
KEY Assigned IN Searching mode(Table 1)
Press AS/PS (D-AUD) button for
three times. The unit searches file or
directory from root by
AS/PS
BND/LOU
M1
Mode Select
ENTER
TUNE/TRACK UP/DOWN buttons.
(D-DIR icon turns on if the name is
directory).
A, B, C, 1
D, E, F, 2
G, H, I, 3
J, K, L, 4
Display will list all available
M2
directories and songs. Select the
desired directory/songs by using
TUNE/TRACK UP/DOWN buttons
and BND/LOU (ENT) button to
confirm. If the selected title is a
song, it starts to play. If the selected
title is a directory name, display will
show (‘ ‘), then
M3
M4
M5
M, N, O, 5/
Directory DOWN
M6
P, Q, R, 6/
- Use the TUNE/TRACK UP/DOWN
buttons to list all songs under this
directory and select the title.
- Press BND/LOU (ENT) button to
confirm and start the play.
- Repeat the above steps if the newly
selected title is again a directory.
• Searching From Current Directory
Press AS/PS (D-AUD) button for
four times. The unit searches file or
directory from current directory by
TUNE/TRACK UP/DOWN buttons.
(D-DIR icon turns on if the name is
directory). The current directory
name is displayed for a second and
the currently playing file name is
displayed (selected). The user can
select the directory or file in the
directory by TUNE/TRACK
Directory UP
MOD
S, T, U, 7
V, W, X, 8
TUNE/TRACK
DOWN
TUNE/TRACK
UP
Y, Z, SPACE, 9
SEL
CHARACTER
SHIFT RIGHT
DSP
_, –, +, 0
AUDIO
KNOB
CHARACTER SELECT
(A, B - 8, 9, 0)
AUDIO KONB (ENCODER) &
TUNE/TRACK UP/DOWN buttons:
Searching file and directory during
Navigation.
UP/DOWN buttons. The selected
file can be played by pressing
BND/LOU (ENT) button.
WMA OPERATION
“MP3” icon turns on when MP3 disc
is played and blinks when it is in
navigation mode.
The unit that can play the WMA disc and
the operation is the same with MP3
operation described above.
• DISPLAY INFORMATION
USB PLAY OPERATION
Press DSP button to show the
following information, such as the
clock, ID3 TAG (if available: song title,
directory name, artist name, other
contents…) and other information.
In the front panel of the unit, there is an
USB interface (24). You can connect an
USB driver through this interface (24). For
the unit with no SD/MMC interface, when
you connect the USB driver through the
interface, the unit will search the MP3 files
or WMA files in the USB driver and start
to play MP3 files or WMA files
automatically. If in other mode, you can
also press MOD button to select USB
mode.
When playing the MP3 files or WMA files
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
in the device, the operation is the same
with the MP3 operation described above.
1. Folder: 1024 max.
2. File: 4096 max.
3. Depth of folder: 8 layers
4. Size: 1 GB
Note:
• The main unit can only support the
standard USB-memory disc which is
approved by Microsoft.
CAUTION:
When there are important files in the USB
device, do not connect it to the main unit
to play. And don't play the CD-R/RW disc
that has important files in it. Because any
wrong operation may cause files loss.
And our company assumes no
responsibility for this.
• USB MP3 player is not a standard which
means different brand name or different
models have their own standard. So
our product cannot support every MP3
player.
• When connecting an MP3 player and
there has normal battery in the player
(non rechargeable battery), you should
remove the battery from the MP3 player
then connect it to the USB interface.
Otherwise, it may cause battery burst.
• When in USB play mode, be sure not
to remove the USB driver from the USB
interface.
DISC NOTE
A. Notes on discs:
1.Attempting to use non-standard shape
discs (e.g. square, start, heart) may
damage the unit. Be sure to use round
shape CD discs only for this unit.
2.Do not stick paper or tape etc., onto
the label side or the recording side of
any discs, as it may cause a
RECORD OPERATION
This unit provides record function. In radio,
CDP mode, CD Changer or AUX mode,
press EQ (REC) button (19) shortly to
activate RECORD mode. The unit will
record files to USB and the format of the
file “.WMA”. The unit can find and
malfunction.
3.Dirt, dust, scratches and warping discs
will cause misoperation.
B. Notes on CD-Rs (recordable
CDs)/CD-RWs (rewritable CDs):
1.Be sure to use discs with following
marks only for the unit to play:
play the record files in the device that
connected to the unit through the USB
interface. There will be shown “file name”
during recording. Press EQ (REC) button
(19) shortly again to complete recording.
Note:
Recordable
Rewritable
• During recording, be sure not to remove
the external device from the USB
interface or turn off the power or switch
off the ACC wire. Otherwise, it may
destroy the record files and the USB
interface may cause a malfunction.
• During recording in one mode, be sure
not to switch to another mode (such as
radio, CD or AUX mode). You must
press EQ (REC) button (19) shortly to
complete recording, then you can
change the current mode.
2.The unit cannot play a CD-R and
CD-RW that is not finalized.
(Please refer to the manual of your
CD-R/CD-RW recorder or CD-R/
CD-RW software for more information
on finalization process).
3.Depending on the recording status,
conditions of the disc and the
equipment used for the recording,
some CD-Rs/CD-RWs may not be
played on this unit. (See *1)
• When playing MP3/MWA disc, the unit
cannot record files to USB.
*1: To have more reliable play back,
please see following
recommendations:
SUPPORTED MP3/WMA DECODING
MODES
a.Use CD-RWs with speed 1x to 4x
and write with speed 1x to 2x.
b.Use CD-Rs with speed 1x to 8x and
write with speed 1x to 2x.
The main unit supports MP3/WMA (Windows
Media Audio) decoding modes as below.
c.Do not play a CD-RW which has
been written for more than 5 times.
C. Notes on MP3 files:
Standard
Bit Rate (kbps) Supports
Mode
MPEG1 Audio 32, 48, 64, 96, Stereo
1.The disc must be in the ISO9660 level
1 or level 2 format, or Joliet or Romeo
in the expansion format.
Layer 3
128, 192, 256,
320
64, 96, 128,
192
(44.1kHz)
Windows
Media Audio
(44.1kHz)
Stereo
2.When naming a MP3 file, be sure the
file name extension is “.MP3”.
3.For a non-MP3 file, even though the
file name extension is “.MP3”, the unit
cannot recognize it.
The USB solution can support:
13
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL HANDSET
1
7
4
3
8
6
9
5
2
13
12
10
14
16
11
15
FUNCTION KEYS & CONTROL
1.
PWR
=
=
=
Power ON/OFF Button
2. DSP (0)
3. SEL
Display Button (_, –, +, 0 For MP3/WMA Operation )
Sound Mode Select Button (Character Shift Right For
MP3/WMA Operation )
4. VOL
=
=
=
Volume Up Button [Character Select (A, B ~ 8, 9, 0) For
MP3/WMA Operation]
Volume Down Button [Character Select (A, B ~ 8, 9, 0) For
MP3/WMA Operation]
Band Select Button (When pressed shortly)
Loudness Button (When pressed long)
5. VOL
6. BND (LOU/ENT)
(Enter Button For MP3/WMA Operation)
Mode Button (S, T, U, 7 For MP3/WMA Operation)
Tune/Skip Down Button; Select Channel Down in XM Mode
(V, W, X, 8 For MP3/WMA Operation)
7. MOD (7)
=
=
(8)
8. TUNE/SEEK
9. TUNE/SEEK
10. AS/PS (D-AUD)
(9) = Tune/Skip Up Button; Select Channel Up in XM Mode (Y,
Z, SPACE, 9 For MP3/WMA Operation)
=
Automatic Memory Storing & Program Scanning Button
(Mode Select Button For MP3/WMA Operation)
Preset Buttons (A~R, 1~6 For MP3/WMA Operation)
Pause Button (A, B, C, 1 For MP3/WMA Operation)
Scanning Button (D, E, F, 2 For MP3/WMA Operation)
Repeat Button (G, H, I, 3 For MP3/WMA Operation)
Shuffle Button (J, K, L, 4 For MP3/WMA Operation)
Local/Distant Select Button; XM Mode Select Button
11. M1 - M6
12. PAU
13. SCN
14. RPT
15. SHF
=
=
=
=
=
=
16. LOC (XM-MOD)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATION
GENERAL
Power Supply Requirements
Chassis Dimensions
Tone Controls
: DC 12 Volts, Negative Ground
: 178 (W) x 160 (D) x 50 (H)
- Bass (at 100 Hz)
- Treble (at 10 KHz)
Maximum Output Power
Current Drain
: ± 10 dB
: ± 10 dB
: 4 x 50 Watts
: 15 Ampere (max.)
CD PLAYER
Signal to Noise Ratio
Channel Separation
Frequency Response
: More than 55 dB
: More than 45 dB
: 40 Hz - 18 KHz
RADIO
FM
Frequency Coverage
IF
Sensitivity (S/N = 30 dB)
Stereo Separation
: 87.5 to 107.9 MHz
: 10.7 MHz
: 4 µV
: > 25 dB
AM
Frequency Coverage
IF
Sensitivity (S/N = 20 dB)
: 530 to 1710 KHz
: 450 KHz
: 36 dBu
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
Symptom
No power.
Cause
Solution
The car ignition switch is
not on.
If the power supply is
connected to the car accessory
circuits, but the engine is not
moving, switch the ignition key
to “ACC”.
The fuse is blown.
Replace the fuse.
Disc cannot be
loaded or ejected. the player.
Presence of CD disc inside Remove the disc in the player,
then put a new one.
Inserting the disc in reverse Insert the compact disc with
direction. the label facing upward.
Compact disc is extremely Clean the disc or try to play a
dirty or defective disc. new one.
Temperature inside the car Cool off or until the ambient
is too high.
temperature return to normal.
Condensation.
Leave the player off for an hour
or so, then try again.
No sound.
Volume is in minimum.
Adjust volume to a desired level.
Check wiring connection.
Wiring is not properly
connected.
Sound skips.
The installation angle is
more than 30 degrees.
Adjust the installation angle less
than 30 degrees.
The disc is extremely dirty
or defective disc.
Clean the compact disc, then
try to play a new one.
The operation keys The built-in microcomputer Press the RESET button.
do not work.
is not operating properly
due to noise.
Front panel is not properly fixed
into its place.
The radio does not The antenna cable is not
Insert the antenna cable firmly.
work. The radio
station automatic
selection does not The signals are too weak.
work.
connected.
Select a station manually.
88-C2007-02
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|