CR-4000 SERIES
CASH DRAWER
USER’ S MANUAL
Rev. : C
NOTICE
The manufacturer of the POS cash drawer makes no representation or warranties, either
expressed or implied, by or with respect to anything in this manual, and shall not be liable
for any implied warranties of fitness for a particular purpose or for any indirect, special or
consequential damages. Information in this document is subject to change without notice
and does not represent a commitment on the part of the manufacturer.
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and if not installed
and used in accordance with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with the limits for a Class A digital
device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide
reasonable protection against interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which case
the user at his own expense will be required to take whatever measures may be required to
correct the interference.
1
P/N: 19240901021
Download from Www.Somanuals.com. All Manuals Search And Download.
b). For CR4001/ 4101/ 4211/ 4002/ 4102/ 4212: CCBLA-196A with one 9PM and one
9PF connector.
c). For CR4003/ 4103/ 4213: CCBLA-089-1 with one 25PM and one 25PF connector.
d). For CR4004/ 4104/ 4214: The serial signal cable is already built on.
e). For CR4005/ 4105/ 4215/ CR4005-II/ 4105-II/ 4215-II: USB cable is already built on.
6. Power Source depend on model
a). For CR-4000/ 4100/ 4210: not applicable
b). For CR-4001/ 4101/ 4211/ 4002/ 4102/ 4212/ 4003/ 4103/ 4213/ 4005/ 4105/ 4215 /
CR4005-II / 4105 -II/ 4215-II: Power adapter 12VAC 1.5A
c). For CR4004/ 4104/ 4214:Power connector cable and I/O bracket plate.
INSTALLATION
CR4000 / 4100 / 4210
Connect the drawer to POS system/printer as shown below:
Rear View
8P Telephone Plug
POS System or Printer
Output to drawer
Control signal input
Ground
CASH DRAWER
8P Telephone Jack
With Printer Interface
6P Telephone Plug
CR4001 / 4101 / 4211
1).Connect the drawer serial I/P port to the computer COM port. Connect the power
adapter output to the Power Input jack
2).No other RS232C devices should be connected to the serial O/P port.
3).Set position 3 of S2 to OFF and position 4 of S2 to ON. Please refer to rear panel
illustration.
CR4002 / 4102 / 4212
1).Connect the drawer serial I/P port to the computer COM port. Connect the power
adapter output to the Power Input jack.
2).Other RS232C device can be connected to the serial O/P port when needed as long as
the security code makes no influence to this RS232C device.
3).Set position 3 of S2 to ON and position 4 of S2 to OFF. Set S1 for security code to open
cash drawer. In normal practice, the security code is suggested to be a non-displayable
ASCII character, for example, a hexadecimal number between 01 to 1F. Please refer to
rear panel illustration below.
CR4003 / 4103 / 4213
1).Connect the drawer parallel I/P port to the computer LPT port. Connect the power
adapter output to the Power Input jack.
2).Other parallel device such as a printer can be connected to the parallel O/P port when
needed as long as the Security code makes no influence to this parallel device.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3).Set S1 for security code to open cash drawer. In normal practice, the security code is
suggested to be a non-displayable ASCII character. For. example, a hexadecimal
number between 01 to 1F. Please refer to rear panel illustration below.
CR4001/ 4101/ 4211/ 4002/ 4102/ 4212/ 4003/ 4103/ 4213 Rear panel illustration.
AC 12V I/P
PARALLEL O/P (DB25F)
Switch is ON when pushed up
SERIAL O/P (DB9M)
S1
S2
8
1 4 1
SERIAL I/P (DB9F)
PARALLEL I/P (DB25M)
GROUND
S1
Set security code. (Default Setting: BIT 1,2,3 OFF and BIT 4,5,6,7,8 ON. Security
code is 07H)
BIT
1
1
2
2
3
4
4
8
5
6
7
8
Number to be added to the
security code if OFF.
16
32
64 128
S2 BIT1 ON and BIT2 OFF to receive security code via Pin2 of P4 (DB9F).
BIT1 OFF and BIT2 ON* to receive security code via Pin3 of P4 (DB9F).
BIT3 OFF and BIT4 ON for dedicated RS-232C.
BIT3 ON and BIT4 OFF* for non-dedicated RS-232C.
(*denotes factory default setting)
616P PHONE JACK
CR4004 / 4104 / 4214
1). Open the PC case. Put the metal
bracket with power connector into one
of the I/O windows.
2). Connect the cable to the HDD type
power connector of PC power supply.
See illustration below. Then close the
PC case.
3). Connect the DB-9 connector to the
computer's serial port of COM1 (or
POWER CORD
COM2). Connect the 4P phone plug connector to the added I/O bracket. See below
illustration.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
COM1
616P PHONE JACK
DB9
4PIN PHONE JACK
CR4005/ 4105/ 4215/ CR4005-II/ 4105-II/ 4215-II
1). Define a drawer number for the cash drawer so that this cash drawer is going to respond
accordingly in USB communication. Follow the table below for SWITCH SETTING to
adjust the switch S1 according to this drawer number if it is not 7. Please note that
within each system there should never be any 2 USB interface cash drawers carrying the
same drawer number.
O
4
3 2
1
N
Connect to USB
Port of Main PC
S1
AC 12V I/P
Power Jack of CR4005/4105/4215/
CR4005-II/ 4105-II/ 4215-II
USB Connector from CR4005/4105/
4215/CR4005-II/ 4105-II/ 4215-II
Rear View of Model CR4005/4105/ 4215/CR4005-II/ 4105-II/ 4215-II Cash
Drawer with USB Interface
SWITCH SETTING:
0
1
2
3
4
5
6
7
Drawer
SW1
ON OFF ON OFF
ON OFF ON OFF
ON ON OFF OFF
ON
ON
ON OFF OFF
SW2
ON
ON
ON OFF OFF OFF OFF
SW3
Reserved
SW4
Default setting: Drawer 7 (SW1: OFF; SW2: OFF; SW3: OFF)
2). Connect USB connector of cable coming out from the rear side of the USB interface
cash drawer to USB port of main PC.
3). Check the specification of power adaptor on its nameplate. Insert the power adaptor into
the correct power outlet. Insert the output plug to the jack at rear side of CR4005/ 4105/
4215/ CR4005-II/ 4105-II/ 4215-II to supply power for drawer kickout.
4). Install the USB utility driver from Posiflex Product Information CD with Posiflex POS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
UPOS driver application (Applied for all Posiflex cash drawer)
Please first find in Posiflex Product Information CDROM or download from Posiflex
web sites for UPOS driver setup. In this application CR4XX3 and CR4XX4 respond to
openDrawer command only; CR4XX0, CR4XX1 and CR4XX2 are compliant to UPOS
version 1.4; CR4XX5 are compliant to UPOS version 1.7 and CR4XX5-II are compliant to
UPOS version 1.8.
FUNCTIONAL TEST
CR4000 / 4100 / 4210
1.Follow the printer’ s manual of the printer the cash drawer is connected to open cash drawer.
2.If the cash drawer is connected to a Posiflex POS system, follow the technical instruction of
the system to open the cash drawer.
CR-4001 / 4101 / 4211 / 4002 / 4102 / 4212 / 4004 / 4104 / 4214
1.Under DOS prompt, type “MODE COM1 96 N 8 1”. Hit the ENTER key.
2.Type “TYPE CON>COM1”. Hit the ENTER key.
3.Type “CTRL-G” (Press Ctrl and G keys together). Hit the ENTER key, then the drawer
will open.
4.Hit CTRL-C (Press Ctrl and C keys together) to return the computer back to the normal
display mode.
In case the cash drawer is connected to serial port other than COM1 please substitute COM1
above to proper port name.
If the pre-set security code of CR-4002/ 4102/ 4212 has been changed from default 07 Hex.
Please change the CTRL-G above accordingly. For CR4001/ 4101/ 4211/ 4004/ 4104/ 4214,
this code can be replaced by any character.
CR-4003 / 4103 / 4213
1.Under DOS prompt, type “TYPE CON>LPT1”. Hit the ENTER key.
2.Type “CTRL-G” (Press Ctrl and G keys together). Hit the ENTER key, then the drawer
will open.
3.Hit CTRL-C (Press Ctrl and C keys together) to return the computer back to the normal
display mode.
If the pre-set security code of CR-4003/ 4103/ 4213 has been changed from default 07 Hex.
Please change the CTRL-G above accordingly.
CR4005/ 4105/ 4215/ CR4005-II/ 4105-II/ 4215-II
1.Please find in Posiflex Product Information CDROM or go to Posiflex web sites (http:
Drawer Test Program. If you use the Posiflex Product Information CDROM that comes
with any Posiflex POS system, please go to folder “\Drivers\CR\USB” and click
“SETUP.EXE” to install the USB Cash Drawer Test Program.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2.Start up the test program and click “STATUS” button. The drawer status of Open/Close or
Not present will be displayed under each drawer number as “O”, “C” or “N”
3.Use a key to turn the lock to standby position (the one marked with sign at middle), click
the check only the box (es) under the drawer number(s) for the drawer(s) to be tested then
click the “KICK” button.
4.The cash drawer will then open and the Open/Close/Not present status of the tested drawer
number will be renewed accordingly. If these status are correct, the USB interface cash
drawer passes the test.
SPECIFICATIONS
MECHANICAL: Dimensions: 428 (W) x 460 (D) x 100 (H) mm
Weight:
6.0 Kgs
Removable tray with a lock-on cover (option)
ELECTRICAL:
Power Source
Solenoid Drive (for CR-4000 / 4100 / 4210)
Pulse Amplitude
12 to 24 VDC
Pulse Width
100 to 250 msec
Pulse Duty Cycle
Max. Current Consumption
10% max.
0.75A @ 12 VDC/1.5A @ 24 VDC
AC Adaptor (for CR-4001/ 4101/ 4211/ 4002/ 4102/ 4212/ 4003/ 4103/ 4213/ 4005/ 4105/
4215/ 4005-II/ 4105-II/ 4215-II)
Input Voltage
Output Voltage
120 VAC ± 10 % / 240 VAC ± 10 % @50 -60 Hz
12 VAC at 1.5 A
DC Power Kit (for CR-4004 / 4104 / 4214): +12 V DC and + 5 V DC
Interface
Direct Drive: CR4000/ 4100/ 4210
Serial (RS232C)
CR-4001
CR-4101
CR-4211
9600
None
8
CR-4002
CR-4102
CR-4212
9600
none
8
CR-4004
CR-4104
CR-4214
150 ~ 19200
none, even, or odd
7 or 8
Baud rate
Parity
Data Bits
Stop Bits
1 or 2
1 or 2
1 or 2
Parallel (IEEE1284): CR-4003/ 4103/ 4213
USB (1.1): CR-4005/ 4105/ 4215/ 4005-II/ 4105-II/ 4215-II
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Code
CR-4002/ 4102/ 4212/ 4003/ 4103/ 4213
CR-4005/ 4105/ 4215/ 4005-II/ 4105-II/ 4215-II
1-255; factory preset value = 7
USB PID
Drawer Open Sense
CR-4000/ 4100/ 4210
CR-4001/ 4101/ 4211/ 4002/ 4102/ 4212
Drawer open sense circuit shorts when open
Pin 9 shorts to pin 5 when drawer open
CR-4005/4105/4215/4005-II/4105-II/4215-II Through USB driver
KEYLOCK OPERATION
Physically lock the drawer.
Open the drawer by the key.
Automatically open the drawer by POS printer
or POS system or interface signal control
STRUCTURE
Check Slot
Inside CR-4000/ 4001/ 4002/ 4003/ 4004/ 4005/ 4005-II/ 4100/ 4101/ 4102/ 4103/ 4104/
4105/ 4105-II
Bill compartment
Bill Clip
Coin compartment
Cash Tray
Coin Roll Storage
Tray for CR-4210/ 4211/ 4212/ 4213/ 4214/ 4215/ 4215-II
Bill compartment
Coin Roll Storage
Cash Tray
Bill Weight
Coin compartment
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|