Parasound Stereo Amplifier 2125 V2 User Manual

Model 2125 v.2  
Two Channel Amplifier  
OWNER’S GUIDE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Introduction  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
4
5
5
6
6
8
9
Placement and Ventilation Guidelines  
Rack Mounting  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
AC Mains Voltage  
Rear Panel Connections and Controls  
Bridged Mono Operation  
A+B Speaker Load Switch  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Turn On Options  
.
.
.
.
.
.
.
.
.
.
.
.
10  
12  
13  
14  
15  
Front Panel Operation.  
Problems and Remedies.  
If You Require Assistance or Warranty Repair  
Specifications  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
Thank You for Choosing Parasound  
Your new Parasound Model 2125 v.2 power amplifier has been designed with proven class AB amplifier  
technology. The Model 2125 v.2 is built to extremely strict quality and performance standards for which  
Parasound is renowned. We’re proud to offer you this exceptional audio component that will bring you  
many years of enjoyment and dependability. We designed your new Model 2125 v.2 Amplifier to perform  
at a higher level of sonic performance than you may have expected and we encourage you to read this  
entire manual to maximize your enjoyment. We wish you many years of listening enjoyment.  
-The Parasound Staff  
Keeping Records for Future Reference  
Record the serial number located on the back panel or bottom of your Model 2125 v.2 in the space  
below. Also note your Parasound Dealer’s name and telephone number. Your purchase receipt/bill of  
sale is required to determine if your Model 2125 v.2 is eligible for Parasound warranty service. We  
recommend that you make an extra copy of your original purchase receipt/bill of sale and store it inside  
the Model 2125 v.2’s carton.  
Parasound Model 2125 v.2 Amplifier Serial #: ______________ (5 digit number below the bar code)  
Parasound Dealer: ___________________________________________________  
Parasound Dealer Phone Number: ___________________  
Date of Purchase: ______________________  
Important Warranty information  
There is no Parasound warranty for this unit if it was not purchased from an Authorized  
Parasound Dealer. Investigate warranty coverage statements made by an unauthorized dealer very  
carefully, as you will need to depend entirely upon your dealer, and NOT upon Parasound.  
Unauthorized dealers lack the capability to make repairs or arrange for repairs of Parasound  
equipment. A list of Authorized Parasound Dealers and detailed warranty information is available at  
www.parasound.com or you can call 415-397-7100 between 8:30 am and 4 pm Pacific time.  
A missing or altered serial number could indicate that this unit was re-sold by an unauthorized dealer or  
is stolen merchandise. If this unit is missing its serial number or the serial number has been altered, you  
should return it to your dealer immediately for a full refund.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Unpacking Your Model 2125 v.2 & Placement Guidelines  
Unpacking Your Model 2125 v.2  
Carefully remove your Model 2125 v.2 from its shipping carton and locate the enclosed accessories:  
• AC power cord  
• Two 12V DC trigger wires with mono plugs, one with 3.5 mm (1/8‖) mini plugs, one with a 2.5mm  
sub-mini plug and a 3.5mm mini plug  
While you are unpacking your Model 2125 v.2, inspect it thoroughly for possible shipping damage and  
tell your Parasound dealer immediately if you find any evidence of shipping damage. This would be a  
good time to make a copy of your sales receipt to store with the Model 2125 v.2’s original packing.  
Note: Please save and store both the inner and outer cartons and, most especially, the foam packing  
inserts to protect the Model 2125 v.2 if you have to move it or ship it. You may wish to flatten the  
cardboard cartons to save room in storage after cutting the taped seams on the bottom flaps.  
Placement Guidelines  
The Model 2125 v.2 will be easier to use and will last longer if you follow these simple guidelines:  
Place the Model 2125 v.2 on a surface that will adequately support its substantial weight.  
Use input and output cables that are long enough to leave some slack; that will enable you to pull  
the Model 2125 v.2 out of a cabinet to check or to change connections without inadvertently  
disconnecting cables.  
The Model 2125 v.2 should never be placed in a completely enclosed cabinet  
Place your Model 2125 v.2 where you can route input and output signal cables as far as possible  
from any AC cords.  
Where signal cables must cross AC cords they should do so only at a 90° right angle.  
Ventilation Requirements  
Always position the Model 2125 v.2 horizontally.  
The Model 2125 v.2 should never be stacked immediately on top of another power amplifier.  
Do not install the Model 2125 v.2 in an unventilated equipment cabinet or compartment. Pockets of  
stagnant hot air can build up even in a cabinet with an open front and back.  
Rack Mounting Your Parasound Model 2125 v.2  
The Model 2125 v.2 front panel occupies two rack spaces in a standard 19‖ equipment rack.  
For rack mounting, you’ll need to use the Parasound RMK22 rack mounting kit (purchased separately).  
We recommend that you use the 8 insulated shoulder washers with the four mounting bolts which are  
included with the RMK22. Position these washers on both sides so they ―sandwich‖ the front panel  
before the mounting bolts are screwed into the rack rail. This will eliminate metal-to-metal contact  
between the Model 2125 v.2 chassis, the equipment rack, and the other components in the rack.  
Note: Tighten each bolt just enough to keep the unit secure in the rack to avoid deforming the shoulder  
washers. Eliminating metal-to-metal contact reduces the likelihood of creating a ground loop that might  
introduce hum into your system.  
A single standard rack space is 1-3⁄4" (44mm) high in a 19" wide equipment rack. This measurement  
standard was developed by the EIA (Electronic Industries Association) so manufacturers of electronic  
components and equipment racks could build products in standardized heights that would fit in a  
uniform space. Please call your Parasound dealer or Parasound Technical Services if you need  
additional advice about rack mounting the Model 2125 v.2.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
AC Mains Voltage  
NOTE: Before you plug this amplifier into an AC mains outlet:  
115v - 230v AC Voltage Selector Switch  
This switch is found on the chassis rear panel. The 115V position of this switch is correct for North  
America; most other regions require setting it to 230V. Make sure the 115/230V switch is set for the  
correct AC line (mains) voltage before you connect the Model 2125 v.2’s power cord and before you  
install it. The unit may be seriously damaged if this switch is set incorrectly.  
AC Voltage Warranty Exclusion  
Amplifiers set for 115V which are damaged by 220V-240V are not covered under the Parasound  
Limited Warranty.  
Rear Panel Connections and Controls  
Always disconnect the AC cord to your Model 2125 v.2 before making or changing any input,  
output or trigger wire connections. Inserting or removing an input or output cable while the Model  
2125 v.2 is turned on can result in a blast of sound that can damage your loudspeakers and your  
hearing. Make sure there is no strain or tension on any cables that could cause them to pull loose.  
R (Right) and L (Left) Audio Input Jacks  
Connect the shielded audio cables from your preamplifier or system controller’s output jacks to the  
Model 2125 v.2’s L and R audio Input jacks. Use only the R channel Input jack for bridged mono  
operation.  
Audio Loop Out Jacks  
The jacks replicate the audio input signals to facilitate connections of other power amplifiers to the  
same preamplifier or system controller. Loop connection of multiple power amplifiers is called a ―daisy  
chain.‖ These Loop Out jacks also provide a convenient way to connect a powered subwoofer.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
R (Right) and L (Left) Level Knobs  
To increase the listening level for each channel, turn its Level knob clockwise. To decrease the  
listening level turn it counter-clockwise. The 2125 has a total gain of 28 dB so that its volume levels are  
compatible with other channels in your theater if they are driven by a THX-certified amplifier, up to the  
point where the THX-certified amplifier might play a bit louder because of its higher power output.  
Note: You may wish to experiment with different gain settings on your preamp or surround  
controller and on the Model 2125 v.2 to find a combination of gain settings where your system’s  
background noise is lowest. Sound professionals call these adjustments ―gain staging.‖  
Note: Only the R channel Level knob is used for bridged mono operation.  
Front Panel Speaker Selector Lockout Switch  
When this switch is set to Normal, the front panel A and B buttons determine whether speaker output  
terminals A and B are live. When this switch is set to Lockout, the front panel A and B buttons are  
disabled and speakers A and B will always be on. This can be particularly useful for a professional  
audio installer who never intends for the client to use the front panel buttons.  
Bridged Mono Switch  
Bridged operation configures the Left and Right channels to function as a single higher powered  
amplifier channel to drive a single speaker. This is how two Model 2125 v.2 amps are used as  
monoblocks to power a pair of speakers. It’s also effective for powering a single passive subwoofer.  
Please note that in bridged mono operation the minimum speaker impedance is 8 Ohms (if the load  
switch is set to 4-8). With the Speaker Load switch set to the 2-3position it is possible to drive two  
8speakers or a single 4speaker. For more information please see the section on Bridged Mono  
Operation in this manual.  
Note: The Model 2125 v.2 power should always be turned off before moving this switch.  
Note: If two speakers are attached for normal stereo operation the sound will be faint and very  
distorted if you accidentally leave the Bridged Mono switch in its Mono position.  
High Pass Filter Switch  
The High Pass Filter can improve the sound in many installations. It’s called a ―high pass‖ filter  
because depending on the switch position it permits signals higher than 20 Hz or 40 Hz to pass, while  
preventing signals below these frequencies from passing.  
The Flat setting of this switch disconnects the filter and the 2125 v.2’s frequency response is  
full range (flat).  
The 20 Hz setting filters out frequencies below 20 Hz at 18 dB per octave. Your speakers have  
greater dynamic range and far less distortion when they don’t receive frequencies which are  
lower than they are capable of reproducing. The 2125 v.2 operates more efficiently when it’s  
not called upon to amplify very low frequencies so you’ll have more power in the range the  
speaker is capable of reproducing. Because the 20 Hz filter also has a steep 18 dB per octave  
slope, it is essentially a sub-sonic filter, and you probably won’t notice any loss of low bass  
unless you’re using very large speakers.  
The 40 Hz switch position filters bass below 40 Hz at 18 dB per octave. This is ideal when the  
2125 v.2 is driving in-wall or in-ceiling speakers because most of them have little useful bass  
output below 40 Hz. You’ll enjoy much cleaner sound and higher undistorted volume levels. Not  
having to amplify bass that’s inaudible with your speakers is another way the 2125 v.2 will run  
cooler.  
Note: Most wall mounted speaker volume controls use stepped autoformers whose highly  
reactive loads occasionally cause amplifier distress and malfunction. The 20 Hz or 40 Hz  
filter settings enable the 2125 v.2 to drive them with ease.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker Connections  
Speaker Terminals  
There are separate speaker terminals for two pairs of speakers, labeled Speaker Pair A and Speaker  
Pair B. The speaker terminals accept speaker wires with banana plugs, spade connectors or bare wire.  
Correct Speaker Polarity is Important  
Polarity refers to + and connections. Speaker wires are coded with color, printing or a ridge on the  
insulation on one of the leads so you know which lead was connected to the + and terminals at the  
other end. This coding will help you keep the + and - polarity consistent for all channels. If some of the  
speakers are wired with incorrect polarity you will significantly affect sound quality.  
Speaker Wire Length and Gauge (thickness)  
When selecting speaker wire, follow these guidelines:  
• Keep the length of your speaker wire as short as possible.  
• Use the thickest wire practical. For lengths greater than 50 feet, use speaker wire with an AWG  
(gauge) of 14 or lower. The smaller the AWG number, the thicker the wire.  
• Do not use speaker wire that is thinner than 16 AWG.  
• Keep wire lengths for both channels as close to equal as possible.  
Bridged Mono Operation  
Bridged operation configures the Left and Right channels to function as a single higher powered  
amplifier channel to drive a single speaker. This is how two Model 2125 v.2 amps are used as  
monoblocks to power a pair of speakers. It’s also effective for powering a single passive subwoofer.  
Careful attention must be paid to the total impedance of all speakers wired to the unit when it is set for  
bridged mono operation. When set to mono the Model 2125 v.2 uses its R channel to amplify only the  
positive half of the audio signal and its L channel to amplify only the negative half of the audio signal. In  
effect, each channel ―sees‖ only half of the speaker’s rated impedance, so that a single 8 ohm speaker  
is actually a 4 ohm load when the amp is bridged to mono. A 4 ohm speaker is a 2 ohm load in bridged  
mono. This is why bridged mono power output can be much higher than the sum of the L and R  
channel outputs for stereo operation. When the Speaker Load switch is set to the 4-8position the  
speaker impedance must be 8 ohms for bridged mono operation. This switch must be set to its 2-3Ω  
position if the speaker impedance is less than 8 ohms.  
Setting Up the Model 2125 v.2 for Bridged Mono Operation:  
1. Turn the unit off and remove the AC cord.  
2. Connect the single RCA cable from the preamp or audio controller to the R channel Input jack.  
3. Set the Bridged Mono switch to the Bridged (Mono) position.  
4. Set the Speaker Load switch to the correct position (see instructions on next page).  
5. Connect the positive + lead of the speaker wire to the red R+ channel terminal of speaker pair A.  
6. Connect the - negative lead of the speaker wire to the red L+ channel terminal of speaker pair A.  
7. Do not connect the Land Rspeaker terminals.  
8. If you have a second mono speaker repeat steps 4 - 6 with the speaker pair B terminals.  
9. Reconnect the AC cord.  
Note: Stereo sound will be faint and distorted if you accidentally leave the Bridging switch in its  
Mono position and a stereo pair of speakers are attached.  
Note: The Model 2125 v.2 will create more heat when it drives a bridged mono speaker or  
multiple speaker pairs. Lower impedance speakers will make it run even hotter. Heat buildup  
greatly reduces the life of the amplifier and nearby components. Please pay attention to the  
instructions for setting the Speaker Load switch to avoid overheating.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to set the Speaker Load switch when the Model 2125 v.2 is  
configured for Bridged Mono operation:  
Single 8 Ohm Speaker  
In this case the Speaker Load switch should be set to 4-8.  
Single 4 or 6 Ohm Speaker  
In this case the Speaker Load switch must be set to 2-3.  
Two 8 Ohm Speakers  
In this case the Speaker Load switch must be set to 2-3. Connect the + wire of the  
first speaker to the Speaker Output A red R channel positive terminal and connect  
the speaker’s – wire to the red L channel positive terminal. Connect the second  
speaker similarly to the Speaker Output B red R and L positive terminals.  
Note: Never connect two 4 ohm speakers for bridged mono operation. This results in a 1  
ohm load on each channel which could cause the amp to overheat and shut down.  
Bi-Amping Using Two Model 2125 v.2 Amplifiers  
If your speakers have separate input terminals for their Low and High frequencies there is usually a  
greater sonic advantage using two Model 2125 v.2 amplifiers to ‖bi-amp‖ your speakers rather than  
bridge them as monoblocks. When bi-amping the Bridged Mono switch must be set to its Normal  
(Stereo) position.  
When set up for bi-amping you will use one channel of one 2125 v.2 to power the high frequency  
drivers and the second channel of the same amp to power the low frequency drivers. Since both  
channels of the amp need the same audio signal you will need to connect the Loop Out jack of one  
channel to the input of the second. If you connected your preamp to the 2125 v.2’s L channel Input  
jack to then you’ll need a short RCA cable to connect the 2125 v.2’s L channel Loop Out jack to its R  
channel Input jack.  
A + B Speaker Load Switch  
The Speaker Load switch gives the Model 2125 the flexibility to drive very low impedance loads. Such  
situations can occur when the Model 2125 is asked to drive multiple pairs of speakers.  
For a single pair of 4 ohm or 8 ohm speakers the Speaker Load switch may be set to its 4-8Ω position.  
The Speaker Load switch must be set to 2-3Ω whenever the load will be lower than 4 ohms. Speaker  
loads below a 4 ohm impedance can cause the Model 2125 v.2 to rapidly overheat and cause audible  
distortion.  
These are examples that require the 2-3 Ω setting:  
1. Driving two pairs of speakers whose impedances are unknown.  
2. Driving two pairs of speakers whose impedances are each lower than 8 ohms. For example,  
two pairs of 4 ohm speakers driven simultaneously = 2 ohm load.  
3. Driving three pairs of 8 ohms speakers simultaneously = 2 .66 ohm load.  
4. Driving a single 4 ohm speaker in Bridged Mono operation = 2 ohm load  
5. Driving two 8 ohm speakers in Bridged Mono operation = 2 ohm load  
Note: For the coolest possible operating temperature we recommend setting the Speaker Load  
switch to 2-3 ohms even if you are using a single pair of 8 ohm speakers.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turn On Options Switch  
For convenience, there are three ways the Model 2125 v.2 can be turned on and off:  
Manually, by pressing the Power button on the front panel.  
Automatically by Audio, when an audio signal is present at the audio Input jacks.  
Automatically by 12V, when a suitable trigger voltage is applied to the 12V input jack.  
Note: When either automatic turn on option is selected  
the front panel Power button is disabled so that power  
on/off is determined solely by the triggering preamp,  
receiver or active audio signal. Pushing the Power  
button will not turn the amp on or off.  
Manual Position  
When the Turn On Options switch is in its Manual position the Model 2125 v.2 must be turned on and  
off manually by pressing the Power button on its front panel every time you wish to use your audio  
system.  
Audio Position (Automatic on/off)  
When the Turn On Options switch is set to one of the two Audio positions, the Model 2125 v.2 will be  
turned on only when an audio signal is present at the L or R Input jacks. After the audio signals cease  
the Model 2125 v.2 will remain on for about 8-10 minutes before shutting off. This prevents unintended  
turn-off during pauses in your music or movies.  
Note: When the Turn On Options switch is set to Audio the Model 2125 v.2 will turn itself on  
immediately when you connect its AC cord, even without any audio signal present. This is normal  
and another reason why all connections and settings should be made before connecting its AC  
cord.  
Quieter: This is the more sensitive setting and the amp will turn on automatically with a very low  
level audio signal corresponding to about 1mV. In most cases this will be the preferred setting. If  
for some reason the amp never turns off you may have some noise in your system that is false  
triggering the automatic turn on circuit. In this case you should use the Louder setting.  
Note: If you need the Model 2125 v.2 to turn on at an even lower volume level, simply turn  
down its L and R Level controls. Try setting the level controls at 12 o’clock and see if  
the volume level is low enough when the amp turns on.  
Louder: This is the less sensitive setting and the amp will turn on automatically with a slightly  
higher level audio signal corresponding to about 6mV. You should first try the Quieter setting. If for  
some reason the amp never turns off when set to Quieter then you can use the Louder setting.  
Note: If the Model 2125 v.2 is driving only passive subwoofer(s), surround or rear  
channels you will achieve more consistent automatic turn on by using the 12V DC  
trigger. At the beginning of most films the sub and surround levels are often lower  
than the minimum level required by the Audio sensing circuit.  
12V Position (Automatic on/off)  
When the Turn On Options switch is set to its 12V position, the Model 2125 v.2 is turned on and off only  
with an external +9 V to +12 V voltage from your preamp or AV Receiver. When the external voltage  
ceases the Model 2125 v.2 will turn off within a few seconds. The 12V switch position disables the front  
panel Power button.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12 Volt Input Jacks  
The Model 2125 v.2 12V input uses a 3.5mm jack (mono). To use the 12V trigger, insert the trigger  
wire plug into this jack and the plug at the wire’s other end into the AV receiver or preamp’s 12V output  
jack. We have included a 3.5mm to 3.5mm trigger wire as well as a 3.5mm to 2.5mm trigger wire.  
Note: If the controller’s trigger output is a + and terminal, you can cut the 3.5mm plug off one  
end of the included trigger wire and attach the bare wires to these terminals. The trigger plug tip is  
+ (positive) and its sleeve (negative).  
12V Loop Out Jack  
The Trigger Out jack lets you loop or ―daisy-chain‖ the incoming trigger voltage to an additional Model  
2125 v.2 or another component(s).  
Triggering multiple devices  
The total load on your preamp’s trigger output(s) is the sum of the trigger current drawn by each of the  
components you’ve looped together. The Model 2125 v.2 trigger circuit draws a negligible 15 mA.  
Check the maximum capacity of your AV receiver, processor or home controller’s trigger outputs so  
you do not overload them by connecting too many power amplifiers. Typical ratings are 50mA to  
100mA.  
3.5mm and 2.5mm trigger jacks  
Some other Parasound power amplifiers and preamplifiers might have 2.5mm ―sub-mini‖ trigger jacks.  
To use the Model 2125 v.2 with products that use a 2.5mm jack we have included a trigger wire with a  
3.5mm plug at one end and a 2.5mm plug at the other end.  
AC Power Cord  
Model 2125 v.2 is supplied with a high quality IEC standard AC cord. Please connect it directly to an  
AC wall outlet or power conditioner that is always ―live.‖ If possible, plug your Model 2125 v.2 into the  
same AC outlet that your preamplifier is plugged into. If different AC outlets are used for the Model 2125  
v.2 and the preamplifier the ground potential between the two outlets might be higher or lower, resulting  
in audible hum.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Panel Operation  
Power Button  
Press the Power button once to turn the Model 2125 v.2 on. Press it again to turn it off. When the unit  
is powered on the L and R indicators should illuminate green. The Power button is inoperative when  
the Turn On Options switch is set to Audio or 12V.  
A and B Speaker Select Buttons  
These buttons turn on the speaker pairs connected to the corresponding Speaker Pair A and B  
terminals. They will also select two single mono speakers connected to the corresponding Speaker Pair  
A and B terminals.  
Note: The front panel buttons are inoperative when the Front Panel  
Speaker Selector switch is set to Lockout.  
Protect Indicator  
The Protect indicator will illuminate red and the unit will stop playing if the amp experiences an external  
fault condition. This prevents possible damage to the unit from continued operation. Examples of  
external fault conditions are short circuited speaker wires, excessive heat and trying to drive too many  
speakers at high levels.  
If Protect illuminates you need to locate and correct the fault; for example, remove the short circuit, let  
the unit cool down, check the load impedance and the setting of the Speaker Load switch or lower the  
volume level. To reset the protection circuit you need to turn the unit off. If the amp is being turned on  
by a 12V trigger or audio sensing trigger then the easiest thing may be to simply unplug the unit from  
the AC outlet for about 10 seconds and then plug it back in.  
Hi-Temp Indicator  
Hi-Temp will illuminate red when the Model 2125 v.2 exceeds its maximum safe operating temperature.  
If this happens the unit will activate its protection circuit and stop playing. It will remain in this protection  
mode until the temperature drops and the unit is turned off to reset its protection circuit. If Hi-Temp  
appears it’s likely the unit has been over-driven at too high a listening level or is attempting to drive a  
speaker load impedance that is too low. It’s also probable the unit has not been provided with sufficient  
ventilation. These conditions must be corrected before turning it on again to resume operation.  
L and R Channel Status Indicators  
L and R will illuminate green when the Model 2125 v.2 power is on and it is operating normally. The L  
indicator will not light if a fault is only in the left channel; the R indicator will not light if a fault is only in  
the right channel. Neither L or R indicators will illuminate if there is a general fault or if the temperature  
is too high.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problems and Remedies  
Unit Will Not Turn On  
Check the setting of the Turn On Options switch. (The front panel Power button will be  
disabled if the switch is set to Audio or 12V). First try the Manual position and see if the  
unit will turn on by pressing the front panel Power button.  
• If using Audio Turn on, try increasing the sensitivity of the audio trigger by setting the Turn  
On Option switch to the ―Quieter‖ position.  
If using Audio Turn on and you need the Model 2125 v.2 to turn on at an even lower volume  
level, simply turn down its L and R Level controls. Try setting the level controls at 12  
o’clock and see if the volume level is low enough when the amp turns on.  
• Check that the AC power is live.  
No Sound From the Speakers (but amp turns on)  
Ensure that the front panel speaker buttons for A and B are turned on (button pressed in).  
Try turning up the Level controls for the Left and Right channel.  
Check that input cables and speaker wires are secure at both ends (turn amp off first).  
• Make sure the preamp is switched to the correct input.  
• Is the Protect light illuminated? Check for excessive temperature, short-circuited speaker  
wires, very low impedance speaker load, and inadequate ventilation.  
Background Hum or Hiss  
If you have cable or satellite TV, try disconnecting the incoming TV or satellite cable; if the  
hum is eliminated you will need a ―cable TV ground isolatoror contact your TV service  
provider for assistance.  
• Make sure insulating shoulder washers are used if unit is rack mounted.  
Make sure all equipment is plugged in to the same AC outlet to eliminate ground loops.  
Try turning down the input Level controls.  
Move audio cables and AC cords away from each other.  
• Try different routes for the audio cables and AC cords.  
The Amp is Overheating or the Hi-Temp Indicator is Illuminated  
• Increase ventilation around the Model 2125 v.2.  
Check speakers for faults.  
Change the Speaker Load switch to the 2-3setting.  
• Remove any nearby external sources of heat such as other audio equipment or heaters.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Are You Having Difficulty?  
Repair or Service  
Call your Parasound dealer first. If the dealer can’t help you with your problem we encourage you to  
call Parasound’s Technical Service Department at 415 397 7100, Monday - Friday, 8am - 4pm  
Pacific Time. We can suggest other diagnostic tests you can easily perform.  
If we determine that your Model 2125 v.2 should be returned to Parasound or an Authorized  
Parasound Warranty Center for inspection and possible servicing, we will provide the location of a  
warranty center near you or shipping instructions for the unit’s return to Parasound.  
Before You Return Any Unit to Parasound for Service  
Before you send your unit to Parasound, you will need to obtain a specific Return Authorization  
(RA) number and shipping instructions from Parasound’s Technical Department. The RA number  
must be clearly marked on the outer carton. Use the original factory packing materials and arrange  
adequate insurance to cover its value. You must include a copy of your purchase receipt, since this  
document establishes the validity of this unit’s warranty. Warranty repairs are only performed by  
Parasound or Parasound Authorized warranty centers when your purchase receipt is from a  
Parasound Authorized Dealer or Parasound Authorized Reseller.  
Shipments Will Be Refused by Parasound Under the Following Conditions:  
1. Unit was sent without the Parasound-assigned RA number marked on the carton.  
2. Unit was sent in an unsuitable shipping carton and packing inserts and is likely to have been  
damaged in transit.  
3. Unit has inadequate packing materials and is likely to have been damaged in transit. Wrapping  
the Model 2125 v.2 with bubble wrap will not protect it during shipment.  
4. Unit was shipped collect for shipping charges. We do not accept collect shipments.  
5. Unit was shipped via the US Postal Service.  
6. Unit was sent to an address other than the address instructed by our Technical Department.  
Warranty Repair  
Please read your accompanying Parasound Limited Warranty carefully to understand the applicable  
rights and limitations. This section provides instructions for obtaining repairs, both for units covered  
under the Parasound Limited Warranty and for units or situations which are outside the Warranty.  
Unit is not eligible for repair under the terms of the Parasound warranty if:  
1. Unit was not purchased from a Parasound Authorized Dealer.  
2. You do not have the original bill of sale or sales receipt from a Parasound Authorized Dealer.  
3. You are not the original owner. The Parasound warranty is not transferable.  
4. Unit’s serial number was removed, modified, or defaced.  
5. Unit shows evidence of abuse and/or misuse.  
6. Unit was modified in any way.  
7. A prior repair was attempted by an unauthorized repair station.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Power Output (RMS power, 20 Hz 20 kHz)  
Input Impedance - 33 k Ω  
All Channels Driven  
150 watts x 2, 8Ω  
225 watts x 2, 4Ω  
Input Sensitivity  
1 V in for 28.28 V out, THX standard  
225 watts x 2, 2Ω (Load switch set to 2-3Ω)  
Inter-Channel Crosstalk  
Bridged Mono  
400 watts x 1, 8Ω  
85 dB @1 kHz, 73 dB @10 kHz, 67 dB @ 20kHz  
400 watts x 1, 4Ω (Load switch set to 2-3Ω)  
Damping Factor - Over 150 at 20Hz  
Current Capacity  
12V Trigger Turn On - DC 9 12V, 15 mA  
35 amps peak per channel  
Audio Turn On  
Quieter: 1 mV  
Louder: 6 mV  
Frequency Response  
20 Hz - 50 kHz, +0/-3 dB, 1 watt  
Dynamic Headroom - 1.3 dB  
AC Power Requirement  
Total Harmonic Distortion  
0.25% at full rated output  
110 - 120 V / 220 -240 V, 50 - 60 Hz  
0.5 watts standby  
0.015% at average listening levels  
32 watts Idle (no audio)  
550 watts full output  
IM Distortion - 0.05 %  
Dimensions  
Transient IM Distortion - Not measurable  
171⁄4‖ Wide  
S/N Ratio  
16‖ Deep, with cables connected  
114 dB at rated output, IHF A-weighted  
106 dB at rated output, unweighted  
93 dB at 2.828 V output, IHF A-weighted  
84 dB at 2.828 V output, unweighted  
4.25‖ High with feet, 3.5‖ panel only (2U)  
(437 x 406 x 107mm, 88.2 mm panel only)  
Net Weight - 27 lbs (12.3 kg)  
Rack Mount Accessory  
May be Purchased Separately: RMK22  
Specifications and features subject to change or improvement without notice.  
Copyright Parasound Product Inc., 2013  
Rev. 1.0  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parasound Products, Inc. 2250 McKinnon Ave, San Francisco, CA 94124  
415-397-7100 / Fax 415-397-0144 www.parasound.com  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Multi Tech Systems Network Router FR3060 User Manual
Murray Lawn Mower 309001x18A User Manual
National Instruments Personal Computer PXI 1411 User Manual
Nautique Boat 216v User Manual
Nikon Mouse AW110 User Manual
Olympus Carrying Case PFL 01 User Manual
Omega Vehicle Security Welding System CCT 05 Series User Manual
Optimus Cassette Player SCP 92 User Manual
Oregon Scientific Automobile Alarm JA200 User Manual
Panasonic Telephone KX FKN550 User Manual