Paradyne Network Router 6218 I1 User Manual
6218-I1 Wireless Router  
User’s Guide  
Document No. 6218-A2-GB23-00  
September 2005  
Download from Www.Somanuals.com. All Manuals Search And Download.  
!
Important Safety Instructions  
1. Read and follow all warning notices and instructions marked on the product or included in the manual.  
2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to  
protect it from overheating, these slots and openings must not be blocked or covered.  
3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power  
cord.  
4. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous high  
voltage points or other risks. Refer all servicing to qualified service personnel.  
5. General purpose cables are used with this product for connection to the network. Special cables, which may be  
required by the regulatory inspection authority for the installation site, are the responsibility of the customer. Use a  
UL Listed, CSA certified, minimum No. 24 AWG line cord for connection to the Digital Subscriber Line (DSL)  
network.  
6. When installed in the final configuration, the product must comply with the applicable Safety Standards and  
regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory  
agencies and inspection authorities to ensure compliance.  
7. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If products  
installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition. Consult  
a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary, implement  
corrective action prior to interconnecting the products.  
8. Input power to this product must be provided by one of the following: (1) a UL Listed/CSA certified power source  
with a Class 2 or Limited Power Source (LPS) output for use in North America, or (2) a certified transformer, with a  
Safety Extra Low Voltage (SELV) output having a maximum of 240 VA available, for use in the country of  
installation.  
9. In addition, since the equipment is to be used with telecommunications circuits, take the following precautions:  
—
—
—
Never install telephone wiring during a lightning storm.  
Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.  
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the  
network interface.  
—
—
Use caution when installing or modifying telephone lines.  
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of  
electric shock from lightning.  
—
Do not use the telephone to report a gas leak in the vicinity of the leak.  
CE Marking  
When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be  
downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Library → Technical Manuals →  
CE Declarations of Conformity.  
FCC Part 15 Declaration  
An FCC Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com.  
Select Support -> Technical Manuals -> Declarations of Conformity.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device  
may not cause harmful interference, and (2) this device must accept any interference received, including interference  
that may cause undesired operation.  
The authority to operate this equipment is conditioned by the requirement that no modifications will be made to the  
equipment unless the changes or modifications are expressly approved by the responsible party.  
6218-A2-GB23-00  
September 2005  
B
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the following measures:  
„
„
„
„
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Notice to Users of the United States Telephone Network  
The following notice applies to versions of the modem that have been FCC Part 68 approved.  
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for  
Terminal Attachment (ACTA). On the bottom side of this equipment is a label that contains, among other information, a  
product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the Telephone  
Company.  
This equipment is intended to connect to the Public Switched Telephone Network through a Universal Service Order  
Code (USOC) type RJ11C jack. A plug and jack used to connect this equipment to the premises wiring and telephone  
network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant  
telephone cord and modular plug is provided with this product. It has been designed to be connected to a compatible  
modular jack that is also compliant.  
The Ringer Equivalence Number (or REN) is used to determine the number of devices that may be connected to a  
telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming  
call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that  
may be connected to a line, as determined by the total RENs, contact the local Telephone Company. The REN for this  
product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the  
REN without a decimal point. For example, 03 represents a REN of 0.3.  
If the modem causes harm to the telephone network, the Telephone Company will notify you in advance that temporary  
discontinuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the  
customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is  
necessary.  
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the  
operation of the equipment. If this happens, the Telephone Company will provide advance notice in order for you to  
make necessary modifications to maintain uninterrupted service. If trouble is experienced with the modem, refer to the  
repair and warranty information in this document.  
If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect  
the equipment until the problem is resolved.  
The user may make no repairs to the equipment.  
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service  
commission or corporation commission for information.  
If the site has specially wired alarm equipment connected to the telephone line, ensure the installation of the modem  
does not disable the alarm equipment. If you have questions about what will disable alarm equipment, consult your  
Telephone Company or a qualified installer.  
C
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Notice to Users of the Canadian Telephone Network  
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is  
confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was  
performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It  
does not imply that Industry Canada approved the equipment.  
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment. The REN  
assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be  
connected to a telephone interface. The termination on an interface may consist of any combination of devices subject  
only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.  
If your equipment is in need of repair, contact your local sales representative, service representative, or distributor  
directly.  
!
CANADA - EMI NOTICE:  
This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations.  
Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du  
Canada.  
Japan Notices  
This is a Class B product based on the standard of the Voluntary Control Council for  
Interference from Information Technology Equipment (VCCI). If this is used near a radio or  
television receiver in a domestic environment, it may cause radio interference. Install and use  
the equipment according to the instruction manual.  
6218-A2-GB23-00  
September 2005  
D
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
E
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
About This Guide  
„
„
„
Document Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . .  
Document Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
v
v
Product-Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi  
1 Introduction  
„
„
„
„
„
„
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1  
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1  
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2  
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2  
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3  
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4  
2 Hardware Installation and PC Setup  
„
„
„
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1  
Connecting the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2  
Configuring Your Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4  
Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5  
Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7  
Windows ME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7  
Windows 95 and Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8  
Windows NT 4.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9  
Logging in to Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10  
„
3 Device Information  
„
„
„
„
„
„
„
„
Status Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1  
WAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2  
LAN Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3  
WAN Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3  
ATM Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4  
ADSL Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4  
ADSL BER Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5  
Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6  
6218-A2-GB23-00  
September 2005  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
„
ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6  
4 Quick Setup  
„
Quick Setup with Auto-Connect Enabled. . . . . . . . . . . . . . . . . . . . . . . 4-1  
Quick Setup with Auto-Connect Disabled . . . . . . . . . . . . . . . . . . . . . . 4-3  
„
5 Advanced Setup  
„
WAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1  
Add Function – ATM PVC Configuration . . . . . . . . . . . . . . . . . . . . 5-2  
Connection Type Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3  
WAN Setup - Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4  
Remove Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4  
WAN Setup Finish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5  
Local Area Network (LAN) Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6  
NAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7  
Virtual Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7  
Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9  
DMZ Host. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10  
Firewall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11  
IP Filtering – Outgoing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11  
IP Filtering – Incoming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12  
Firewall – MAC Filtering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13  
Port Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15  
Quality of Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16  
Routing – Default Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17  
Routing – Static Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18  
Routing – RIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19  
DNS Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20  
Dynamic DNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20  
ADSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22  
Modulation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22  
Phone Line Pair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22  
Capability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23  
DSL Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23  
Tone Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24  
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
ii  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
„
Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25  
Wireless - Basic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25  
Wireless - Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25  
Wireless - MAC Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27  
Wireless - Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28  
Wireless - Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28  
6 Diagnostics  
„
Testing the DSL Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1  
7 Management  
„
„
„
„
„
Saving and Restoring the Configuration . . . . . . . . . . . . . . . . . . . . . . . 7-1  
Backing Up Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1  
Restoring Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3  
Restoring Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5  
System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6  
View System Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7  
Configure System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8  
SNMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9  
Internet Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10  
Access Control – Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11  
Access Control – IP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11  
Access Control – Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12  
Update Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13  
Reboot Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14  
„
„
„
„
„
„
„
A Specifications  
Index  
6218-A2-GB23-00  
September 2005  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
iv  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
About This Guide  
Document Purpose and Intended Audience  
This guide contains detailed information about the 6218-I1 router. It is intended for  
all users of the router.  
Document Summary  
Section  
Description  
Chapter 1, Introduction  
Describes the features of the router.  
Chapter 2, Hardware  
Installation and PC Setup  
Shows how to connect the router and set up your PC to  
manage the router.  
Chapter 3, Device Information  
Explains how to use the web interface to obtain  
statistics and other information about the router.  
Chapter 4, Quick Setup  
Describes the Quick Setup configuration process.  
Chapter 5, Advanced Setup  
Describes configuration of the advanced router  
features.  
Chapter 6, Diagnostics  
Describes the test screen.  
Chapter 7, Management  
Describes the management functions of the router,  
including backing up and restoring configuration  
settings, viewing the system log, configuraing access  
control, and upgrading software.  
Appendix A, Specifications  
Index  
Lists the specifications of the router.  
Lists key terms, concepts, and sections in alphabetical  
order.  
A master glossary of terms and acronyms used in Paradyne documents is  
available online at www.paradyne.com. Select Support → Technical Manuals →  
Technical Glossary.  
6218-A2-GB23-00  
September 2005  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
About This Guide  
Product-Related Documents  
Complete documentation for Paradyne products is available online at  
www.paradyne.com. Select Support → Technical Manuals.  
To order a paper copy of a Paradyne document, or to speak with a sales  
representative, please call 1-727-530-2000.  
vi  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Introduction  
1
Introduction  
Features  
Congratulations on becoming the owner of a 6218 wireless router.  
This User’s Guide will show you how to set up the router, and how to customize its  
configuration to get the most out of this product.  
The 6218 router has the following features:  
„
Built-in Asynchronous Digital Subscriber Line (ADSL) modem which offers  
G.dmt, G.lite, T1.413, ADSL2, Annex L, and ADSL2+ to meet different linking  
speeds from your Internet Service Provider (ISP)  
„
„
„
Four 10/100BaseT Ethernet ports to provide Internet connectivity to  
computers on your Local Area Network (LAN)  
802.11g Wi-Fi wireless support to provide Internet connectivity to all wireless  
devices on your LAN  
Easy-to-use configuration program accessible through a standard web  
browser  
6218-A2-GB23-00  
September 2005  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
1. Introduction  
System Requirements  
In order to use the 6218 wireless router for Internet access, you must have the  
following:  
„
„
ADSL service subscription from your ISP  
A PC with:  
— An Ethernet 10/100BaseT network interface card  
— A processor equivalent to or faster than a Pentium II 133 MHz  
— 32 MB RAM or greater  
— Windows 95b, 98, 98SE, 2000, ME, NT, or XP (Note: Windows 95 requires  
the installation of the Winsock program, not included.)  
— (Optional) An Ethernet hub or switch, if you wish to connect the router to  
several computers on an Ethernet network.  
— For system configuration using the supplied web-based program: a web  
browser such as Internet Explorer Version 6.0 or later. Netscape is not  
supported.  
Parts List  
In addition to this document, your 6218 wireless router should come with the  
following:  
„
„
„
„
6218 wireless router  
Power adapter  
Ethernet cable (RJ45, straight-through type)  
Phone cable (RJ11)  
1-2  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
1. Introduction  
Front Panel  
The front panel contains LED indicators that show the status of the unit.  
AP  
xDSL  
xDSL  
LINK  
LAN1  
LAN2  
LAN3  
ALARM  
LAN4  
POWER  
ACT  
05-17713  
Figure 1-1. Front Panel LEDs  
Table 1-1. Front Panel Label and LEDs  
Label  
Color  
Function  
xDSL LNK  
Green  
On: ADSL link is established.  
Flashing: ADSL link is established and active.  
Off: No ADSL link.  
xDSL ACT  
Green  
Green  
Off: No PPP connection is established or the connection is  
not used.  
Blinking: a PPP connection is being attempted.  
Solid: A PPP connection is established.  
Flickering: There is activity over the link.  
LAN 1–4  
On: The Ethernet interface is successfully connected to a  
device through the LAN port.  
Flashing: Data transfer at LAN connection  
Off: No LAN link  
ALARM  
POWER  
Red  
On: ADSL is not connected.  
Off: ADSL is connected.  
On: Unit is powered on.  
Green  
Off: Unit is powered off.  
6218-A2-GB23-00  
September 2005  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
1. Introduction  
Rear Panel  
ON/OFF  
POWER  
LAN4  
LAN3  
LAN2  
LAN1  
LINE  
RESET  
DEF  
CONSOLE  
AUL  
T
05-17714  
Figure 1-2. Back Panel  
The rear panel contains the ports for the router's data and power connections.  
Table 1-2. Rear Panel Labels and Connectors  
Label  
LINE  
Function  
Connects to your ADSL line  
LAN 1–4  
Connects the router to Ethernet devices on your LAN, such  
as your PC's Ethernet port, or the uplink port on a hub or  
switch  
RESET/DEFAULT  
POWER  
To reset the router to its default settings  
Connects to the supplied power adapter  
1-4  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Hardware Installation and  
PC Setup  
2
Overview  
This chapter provides basic instructions for connecting the router to a computer or  
a LAN and to the Internet using DSL. The first part provides instructions to set up  
the hardware, and the second part describes how to prepare your PC for use with  
the router.  
It is assumed that you have already subscribed to DSL service with your Internet  
service provider (ISP).  
6218-A2-GB23-00  
September 2005  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
2. Hardware Installation and PC Setup  
Connecting the Hardware  
Shut down your PC and any other equipment before connecting it to the router. To  
connect your router:  
Procedure  
1. Verify that the router’s power switch is in the Off (outward) position. Verify that  
any PCs and other LAN devices you will attach (such as hubs or switches) are  
turned off.  
2. Use the provided modular phone cable to connect the LINE jack of the router  
to your RJ11 wall jack.  
3. Use the provided Ethernet cable to connect your computer to the router.  
Attach one end of the Ethernet cable to one of the LAN ports on the back of  
the router and connect the other end to the Ethernet port or Network Interface  
Card (NIC) in your PC.  
Connect any other PCs, hubs, and switches to the remaining LAN ports. Either  
a crossover or a straight-through Ethernet cable can be used: the router  
determines the type of signal required.  
4. Connect the cylindrical power plug into the POWER connector on the back of  
the device. Next:  
— If you have a wall-mount adapter, plug the AC adapter into a wall outlet or  
a power strip.  
— If you have a table-top adapter, use the AC power cord to connect the  
adapter to a wall outlet or power strip.  
The supplied power adapter may look different than the one illustrated here.  
5. Turn on your PC and any other LAN devices, such as hubs or switches.  
6. Turn on the router using its power switch.  
7. Verify that the router's LEDs are illuminated as shown in Table 2-1.  
2-2  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
2. Hardware Installation and PC Setup  
ON/OFF  
POWER  
LAN4  
LAN3  
LAN2  
LAN1  
LINE  
RESET  
DEF  
CONSOLE  
AUL  
T
05-17715  
Figure 2-1. Hardware Installation  
Table 2-1. LED Indicators  
This LED . . .  
Should be:  
POWER  
Solid green to indicate that the device is turned on. If this light is not  
on, check if the power adapter is attached to the router and plugged  
into an AC power source.  
STATUS  
ACTIVITY  
LAN  
Solid green to indicate that the router can communicate with your ISP  
via ADSL, or flashing when the router is trying to connect to your ISP.  
Flashing when the device is sending or receiving data over the ADSL  
connection.  
Solid green to indicate that the device can communicate with your PC  
via Ethernet, or flashing when the router is sending or receiving data  
over Ethernet.  
If the LEDs are illuminated as expected, the router is working properly.  
6218-A2-GB23-00  
September 2005  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Hardware Installation and PC Setup  
Configuring Your Computer  
Before you can access the router over the LAN you have to configure your PC's  
TCP/IP address to be 192.168.1.x (where x is any number between 3 and 254),  
with a subnet mask of 255.255.255.0. Your router's default IP address is  
192.168.1.1.  
If you know the version of Windows that you use, go to the appropriate section  
below to learn how to set the IP address of your PC. To determine the version of  
Windows running on your PC, click on the Windows Start button, then click on  
Run... in the Start menu. Type winver in the Open selection box and click on OK.  
Figure 2-2. Windows Run Dialog  
The Windows version is displayed.  
Figure 2-3. Windows Version  
2-4  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
2. Hardware Installation and PC Setup  
Windows XP  
1. In the Windows task bar, click on the Start button, and then click on Control  
Panel.  
2. Double-click on the Network Connections icon.  
3. In the LAN or High-Speed Internet window, right-click on the icon  
corresponding to your network interface card (NIC), and select Properties.  
(Often this icon is labeled Local Area Connection). The Local Area Connection  
dialog box displays with a list of currently installed network items.  
4. Ensure that the check box to the left of the item labeled Internet Protocol  
(TCP/IP) is checked, and click on Properties.  
Figure 2-4. Network Connections (Windows XP)  
6218-A2-GB23-00  
September 2005  
2-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Hardware Installation and PC Setup  
Figure 2-5. Local Area Connection Properties (Windows XP)  
5. In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio  
button labeled Use the following IP address. Type an address between  
192.168.1.3 and 192.168.1.254 in the IP Address field (192.168.1.20 is shown  
here as an example) and 255.255.255.0 in the Subnet Mask field.  
Figure 2-6. TCP/IP Properties (Windows XP)  
6. Click on OK twice to confirm your changes, and close the Control Panel.  
2-6  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Hardware Installation and PC Setup  
Windows 2000  
1. In the Windows task bar, click on the Start button, point to Settings, and then  
click on Control Panel.  
2. Double-click on the Network and Dial-up Connections icon.  
3. In the Network and Dial-up Connections window, right-click on the Local Area  
Connection icon, and then select Properties.  
The Local Area Connection Properties dialog box display a list of currently  
installed network components. If the list includes Internet Protocol (TCP/IP),  
the protocol has already been enabled; skip to Step 10.  
4. If Internet Protocol (TCP/IP) does not appear as an installed component, click  
on Install.  
5. In the Select Network Component Type dialog box, select Protocol, and then  
click on Add.  
6. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click  
on OK.  
You may be prompted to install files from your Windows 2000 installation CD  
or other medium. Follow the instructions to install the files.  
7. If prompted, click on OK to restart your computer with the new settings.  
8. After restarting your PC, double-click on the Network and Dial-up Connections  
icon in the Control Panel.  
9. In Network and Dial-up Connections window, right-click on the Local Area  
Connection icon, and then select Properties.  
10. In the Local Area Connection Properties dialog box, select Internet Protocol  
(TCP/IP), and then click on Properties.  
11. In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio  
button labeled Use the following IP address. Type an address between  
192.168.1.3 and 192.168.1.254 in the IP Address field and 255.255.255.0 in  
the Subnet Mask field.  
12. Click on OK twice to confirm and save your changes, and then close the  
Control Panel.  
Windows ME  
1. In the Windows task bar, click on the Start button, point to Settings, and then  
click on Control Panel.  
2. Double-click on the Network and Dial-up Connections icon.  
3. In the Network and Dial-up Connections window, right-click on the Network  
icon, and then select Properties.  
The Network Properties dialog box displays a list of currently installed network  
components. If the list includes Internet Protocol (TCP/IP), the protocol has  
already been enabled; skip to Step 11.  
6218-A2-GB23-00  
September 2005  
2-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
2. Hardware Installation and PC Setup  
4. If Internet Protocol (TCP/IP) does not appear as an installed component, click  
on Add.  
5. In the Select Network Component Type dialog box, select Protocol, and then  
click on Add.  
6. Select Microsoft in the Manufacturers box.  
7. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click  
on OK.  
You may be prompted to install files from your Windows Me installation CD or  
other media. Follow the instructions to install the files.  
8. If prompted, click on OK to restart your computer with the new settings.  
9. After restarting your PC, double-click on the Network and Dial-up Connections  
icon in the Control Panel.  
10. In Network and Dial-up Connections window, right-click on the Network icon,  
and then select Properties.  
11. In the Network Properties dialog box, select TCP/IP, and then click on  
Properties.  
12. In the TCP/IP Settings dialog box, click on the radio button labeled Use the  
following IP address. Type an address between 192.168.1.3 and  
192.168.1.254 in the IP Address field and 255.255.255.0 in the Subnet Mask  
field.  
13. Click on OK twice to confirm and save your changes, and then close the  
Control Panel.  
Windows 95 and Windows 98  
1. In the Windows task bar, click on the Start button, point to Settings, and then  
click on Control Panel.  
2. Double-click on the Network icon.  
The Network dialog box displays a list of currently installed network  
components. If the list includes TCP/IP, the protocol has already been  
enabled. Skip to step 9.  
3. If TCP/IP does not appear as an installed component, click on Add. The Select  
Network Component Type dialog box appears.  
4. Select Protocol, and then click on Add.  
The Select Network Protocol dialog box appears.  
5. Click on Microsoft in the Manufacturers list box, and then click on TCP/IP in  
the Network Protocols list box.  
6. Click on OK to return to the Network dialog box, and then click on OK again.  
You may be prompted to install files from your Windows 95/98 installation CD.  
Follow the instructions to install the files.  
7. Click on OK to restart the PC and complete the TCP/IP installation.  
2-8  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
2. Hardware Installation and PC Setup  
8. After restarting your PC, open the Control Panel window, and then click on the  
Network icon.  
9. Select the network component labeled TCP/IP, and then click on Properties.  
If you have multiple TCP/IP listings, select the listing associated with your  
network card or adapter.  
10. In the TCP/IP Properties dialog box, click on the IP Address tab.  
11. Click in the radio button labeled Use the following IP address. Type an address  
between 192.168.1.3 and 192.168.1.254 in the IP Address field and  
255.255.255.0 in the Subnet Mask field.  
12. Click on OK twice to confirm and save your changes. You will be prompted to  
restart Windows. Click on Yes.  
Windows NT 4.0  
1. In the Windows NT task bar, click on the Start button, point to Settings, and  
then click on Control Panel.  
2. In the Control Panel window, double click on the Network icon.  
3. In the Network dialog box, click on the Protocols tab.  
The Protocols tab displays a list of currently installed network protocols. If the  
list includes TCP/IP, the protocol has already been enabled. Skip to Step 9.  
4. If TCP/IP does not appear as an installed component, click on Add.  
5. In the Select Network Protocol dialog box, select TCP/IP, and then click on  
OK.  
You may be prompted to install files from your Windows NT installation CD or  
other medium. Follow the instructions to install the files.  
After all files are installed, a window appears to inform you that a TCP/IP  
service called DHCP can be set up to dynamically assign IP information.  
6. Click on Yes to continue, and then click on OK, if prompted, to restart your  
computer.  
7. After restarting your PC, open the Control Panel window, and then double-click  
on the Network icon.  
8. In the Network dialog box, click on the Protocols tab.  
9. In the Protocols tab, select TCP/IP, and then click on Properties.  
10. In the Microsoft TCP/IP Properties dialog box, click on the radio button labeled  
Use the following IP address. Type an address between 192.168.1.3 and  
192.168.1.254 in the IP Address field and 255.255.255.0 in the Subnet Mask  
field.  
11. Click on OK twice to confirm and save your changes, and then close the  
Control Panel.  
6218-A2-GB23-00  
September 2005  
2-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
2. Hardware Installation and PC Setup  
Logging in to Your Router  
This section shows how to connect to the router's web interface, configure  
settings, and observe some statistics of your Internet connection.  
1. Open your Web browser, and type the following URL in the address/location  
box, and press Enter:  
http://192.168.1.1  
This is the default IP address for the LAN port on the router.  
A login screen appears.  
Figure 2-7. Login Screen  
If you have problem connecting to the router, verify that your PC is properly  
configured within the subnet of the router's default IP address 192.168.1.1.  
Setup is described in Configuring Your Computer on page 2-4.  
2. Enter your user name and password, and then click on OK to display the home  
page of the router's web interface. There are two default user name and  
password combinations:  
Table 2-2. Default User Names and Passwords  
User Name  
Password  
Capability  
user  
user  
Can display device status, but cannot change or save  
configuration options.  
admin  
admin  
Can perform all functions.  
You can change the passwords at any time.  
2-10  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Hardware Installation and PC Setup  
The home page is shown in Figure 2-8.  
Figure 2-8. Web Interface Home Page  
6218-A2-GB23-00  
September 2005  
2-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Hardware Installation and PC Setup  
2-12  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Device Information  
3
Status Summary  
Display the general status report for the router by clicking on Summary under  
Device Info (Figure 3-1).  
Figure 3-1. Status Summary  
6218-A2-GB23-00  
September 2005  
3-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
3. Device Information  
WAN  
Display the WAN status report from the by clicking on WAN under Device Info  
(Figure 3-2).  
Figure 3-2. WAN Status  
When a WAN connection is configured, the screen looks like Figure 3-3.  
Figure 3-3. WAN Status with WAN Connection  
3-2  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
3. Device Information  
LAN Statistics  
Display LAN statistics by clicking on LAN under Statistics (Figure 3-4).  
Figure 3-4. LAN Statistics  
WAN Statistics  
Display WAN statistics by clicking on WAN under Statistics (Figure 3-5).  
Figure 3-5. WAN Statistics  
6218-A2-GB23-00  
September 2005  
3-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
3. Device Information  
ATM Statistics  
Display ATM statistics by clicking on ATM under Statistics (Figure 3-6).  
Figure 3-6. ATM Statistics  
ADSL Statistics  
Display ADSL statistics by clicking on ADSL under Statistics (Figure 3-7).  
Figure 3-7. ADSL Status  
3-4  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
3. Device Information  
ADSL BER Test  
The ADSL Bit Error Rate (BER) test determines the quality of the ADSL  
connection. The test is performed by transferring idle cells containing a known  
pattern and comparing the received data with this known pattern to check for any  
errors (Figure 3-8 and Figure 3-9).  
Procedure  
To run a BER test:  
1. Click on the ADSL BER Test button.  
2. Select the test duration and click on Start  
3. Check the result.  
Figure 3-8. ADSL BER Test — Start  
Figure 3-9. ADSL BER Test — Result  
6218-A2-GB23-00  
September 2005  
3-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
3. Device Information  
Route  
Obtain the Routing status report by clicking on the Route item under Device Info  
(Figure 3-10)  
Figure 3-10. Route Information  
ARP  
Display the ARP status report by clicking on ARP under Device Info (Figure 3-11)  
Figure 3-11. ARP Status  
3-6  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Quick Setup  
4
Quick Setup with Auto-Connect Enabled  
Auto-connect will automatically detect the first usable PVC and automatically  
detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server available). To use  
auto-connect:  
Procedure  
1. Select Quick Setup. The Quick Setup initial screen appears.  
Figure 4-1. Quick Setup Initial Screen  
6218-A2-GB23-00  
September 2005  
4-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
4. Quick Setup  
2. Select DSL Auto-Connect, then click on Next. The progress information  
screen appears.  
Figure 4-2. Detecting Available PVC  
Figure 4-3. Detecting available PVC – Available PVC Detected  
4-2  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Quick Setup  
Quick Setup with Auto-Connect Disabled  
Procedure  
1. Select Quick Setup. The Quick Setup initial screen appears.  
2. Verify that DSL Auto-Connect is not selected. Entry boxes for VPI and VCI  
appear when DSL Auto-Connect is not selected.  
3. Specify VPI and VCI as directed by your ISP.  
Figure 4-4. Specifying VPI and VCI  
4. Click on Next. The Connection Type screen appears.  
Figure 4-5. Connection Type  
5. Select the protocol and encapsulation type required by your ISP.  
6218-A2-GB23-00  
September 2005  
4-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Quick Setup  
6. Click on Next. Further parameters for the selected protocol are presented. For  
example, if you selected PPPoA, the PPP Username and Password screen  
appears.  
Figure 4-6. PPP Username and Password  
7. Click on Next. The Network Address Translation Settings screen appears.  
Figure 4-7. NAT Settings  
4-4  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Quick Setup  
8. Enter the settings specified by your ISP and click on Next. The Device Setup  
screen appears.  
Figure 4-8. Device Setup  
9. If desired, configure configure the DSL Router IP address and Subnet Mask  
for the LAN interface to correspond to your LAN's IP Subnet. If you want the  
DHCP server to automatically assign IP addresses, then enable the DHCP  
server and enter the range of IP addresses that the DHCP server can assign  
to your computers. Disable the DHCP server if you would like to manually  
assign IP addresses.  
If you have a second IP address and subnet mask for the LAN interface, click  
on the checkbox to configure it.  
6218-A2-GB23-00  
September 2005  
4-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Quick Setup  
10. Click on Next to continue. The WAN Setup Summary screen displays all WAN  
settings that you have made. Check that the settings are correct before  
clicking on the Save / Reboot button. Clicking on Save / Reboot saves your  
settings and restarts your router.  
Figure 4-9. WAN Setup - Summary  
4-6  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced Setup  
5
WAN  
Set up WAN parameters as directed by your ISP.  
Figure 5-1. WAN Setup Screen  
6218-A2-GB23-00  
September 2005  
5-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
5. Advanced Setup  
Add Function – ATM PVC Configuration  
If you want to add a new rule for the WAN interface, click on the Add button. The  
ATM PVC Configuration screen appears. The ATM PVC Configuration screen  
allows you to configure an ATM PVC identifier (VPI and VCI) and select a service  
category.  
Figure 5-2. ATM PVC Configuration Screen  
Verify the following values with your ISP before you change them.  
„
„
„
VPI (Virtual Path Identifier) – The valid range is 0 to 255.  
VCI (Virtual Channel Identifier) – The valid range is 32 to 65535.  
Service Category – Five classes of traffic defined are defined:  
— UBR Without PCR (Unspecified Bit Rate without Peak Cell Rate)  
— UBR With PCR (Unspecified Bit Rate with Peak Cell Rate) – UBR service  
is suitable for applications that can tolerate variable delays and some cell  
loss, such as data transfer, messaging, distribution, and retrieval, and  
remote terminal applications such as telecommuting.  
— CBR (Constant Bit Rate) – Used by applications that require a fixed data  
rate that is continuously available during the connection time. It is  
commonly used for uncompressed audio and video information such as  
videoconferencing, interactive audio (telephony), and audio and video  
distribution and retrieval.  
— Non-Realtime VBR (Non-Real-time Variable Bit Rate) – Can be used for  
data transfers that have critical response-time requirements such as  
airline reservations, banking transactions, and process monitoring.  
— Realtime VBR (Real-time Variable Bit Rate) – Used for time-sensitive  
applications such as real-time video. Rt-VBR service allows the network  
more flexibility than CBR.  
5-2  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
5. Advanced Setup  
Connection Type Screen  
1. Select the type of network protocol and encapsulation mode over the ATM  
PVC that your ISP has instructed you to use, then click on Next button.  
Figure 5-3. Connection Type Screen  
2. Select a connection type and click on Next. In this example, the Bridge Service  
screen appears.  
Figure 5-4. Bridge Service Screen  
3. Enter or select the parameters presented for the service type, and click on  
Next. The WAN Setup - Summary screen appears.  
6218-A2-GB23-00  
September 2005  
5-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
WAN Setup - Summary  
1. Make sure that the settings on the WAN Setup - Summary screen match the  
settings provided by your ISP. If all settings are correct, click on the Save  
button to save these settings; if not, click on the Back button to make any  
modifications. If you want to change any item after saving, click on the Edit  
button to make any modifications.  
Figure 5-5. WAN Setup Summary  
2. Activate this WAN interface by clicking on the Finish button and further  
configuring services over this interface. The router supports up to five WAN  
connections.  
Remove Function  
If you want to delete a connection from the listed WAN setup, click in the Remove  
check box next to the item, then click on the Remove button.  
Figure 5-6. WAN Setup List  
5-4  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
5. Advanced Setup  
WAN Setup Finish  
After you change any item in WAN Setup, click on the Finish button to apply the  
changes and reboot the system.  
Figure 5-7. WAN Setup Reboot Message  
6218-A2-GB23-00  
September 2005  
5-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Advanced Setup  
Local Area Network (LAN) Setup  
You can configure the DSL Router IP address and Subnet Mask for the LAN  
interface to conform your LAN's IP Subnet.  
The Save button only saves the LAN configuration data. The Save/Reboot button  
saves the LAN configuration data and reboots the router to make the new  
configuration effective.  
Figure 5-8. LAN Setup  
5-6  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
NAT  
You can configure the Virtual Server, Port Triggering, and DMZ Host when NAT is  
enabled.  
Virtual Servers  
A virtual server allows you to direct incoming traffic from the WAN side to a specific  
IP address on the LAN side. Click on the Add button to add a virtual server.  
Figure 5-9. NAT Virtual Server Setup  
6218-A2-GB23-00  
September 2005  
5-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
5. Advanced Setup  
You can select a Service or make new one. Enter the Server IP Address, then click  
on Save/Apply to submit your configuration.  
Figure 5-10. Virtual Server Add Screen  
On this screen you can view and delete servers. Click in the check box under  
Remove and click on the Remove button to delete selected virtual servers.  
Figure 5-11. Removing Selected Virtual Servers  
5-8  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Advanced Setup  
Port Triggering  
Click the on the Add button to add Port Triggering for your Internet application.  
Figure 5-12. Port Triggering Setup Page  
You can select an application every time or create new one for your application.  
Then click on Save/Apply to save your settings.  
Figure 5-13. Port Triggering Add Page  
6218-A2-GB23-00  
September 2005  
5-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
The Port Triggering list screen appears after you save your selections. You can  
delete an entry by clicking in the Remove column then clicking on the Remove  
button.  
Figure 5-14. Port Triggering List  
DMZ Host  
You can define the IP address of the DMZ Host on this screen. Enter the IP  
address and click on Save/Apply.  
Figure 5-15. DMZ Host Setup  
5-10  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
Firewall  
For security reasons, firewall options can be configured only from the LAN side of  
the router.  
IP Filtering – Outgoing  
The outgoing filter will block the traffic from the LAN side to the WAN side. Click on  
Add to create filters.  
Figure 5-16. IP Filtering – Outgoing Filter Setup  
Input the filter name, source information (from the LAN side), and Destination  
information (from the WAN side). Then click on Save/Apply.  
Figure 5-17. IP Filtering - Outgoing Filter Add Page  
6218-A2-GB23-00  
September 2005  
5-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
5. Advanced Setup  
IP Filtering – Incoming  
Incoming filter filters the traffic from the WAN side to the LAN side. Click on Add to  
add incoming filter settings.  
Figure 5-18. IP Filtering – Incoming Filter Setup Page  
Enter a filter name, information about the source address (from the WAN side),  
and information about the destination address ( to the LAN side). Select the  
protocol and WAN interface. Then click on Save/Apply to add the setting.  
Figure 5-19. IP Filtering - Incoming Filter Add  
5-12  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
Firewall – MAC Filtering  
MAC filtering can forward or block traffic by MAC address. You can change the  
policy or add settings to the MAC filtering table using the MAC Filtering Setup  
screen.  
Figure 5-20. IP Filtering - MAC Filtering Setup  
If you click on Change Policy, a confirmation dialog lets you verify your change.  
Figure 5-21. IP Filtering - MAC Filtering Policy Change Confirmation  
6218-A2-GB23-00  
September 2005  
5-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
If you want to add a setting to the MAC filtering table, enter the Source and  
Destination MAC address, and select protocol type, frame direction, and WAN  
interface. Then click on Save/Apply to save it.  
Figure 5-22. IP Filtering - MAC Filtering Add Page  
5-14  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Advanced Setup  
Port Mapping  
Use the Port Mapping screen to map multiple ports to a PVC and create bridging  
groups. Each group will perform as an independent network.  
Figure 5-23. Port Mapping  
To create a new mapping group:  
1. Click on Add. The Port Mapping Configuration screen appears.  
Figure 5-24. Creating a Port Mapping Entry  
2. Enter a unique Group name.  
3. Select interfaces from the available interface list and add them to the grouped  
interface list using the arrow buttons to create the required mapping of the  
ports.  
4. Click on Save/Apply.  
6218-A2-GB23-00  
September 2005  
5-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
Quality of Service  
You can configure the Quality of Service to apply different priorities to traffic on the  
router.  
Figure 5-25. Quality of Service Setup  
Click on Add and the Add Network Traffic Class Rule screen appears. To add a  
rule:  
1. Give a name to this traffic class.  
2. Assign a priority level-low, medium, and high-to this traffic class.  
3. Select an IP precedence from the range of 0–7.  
4. Enter an IP Type of Service from the following selections-  
— Normal Service  
— Minimize Cost  
— Maximize Reliability  
— Maximize Throughput  
— Minimize Delay  
5. Last, enter the traffic conditions for the class such as the protocol (TCP / UDP,  
TCP, UDP, or ICMP) to be used.  
6. Click on Save / Apply to save the settings.  
5-16  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
Figure 5-26. Quality of Service Add Screen  
Routing – Default Gateway  
You can change the Default Gateway on the Routing - Default Gateway screen. By  
default the Enable Automatic Assigned Default Gateway box is checked.  
Figure 5-27. Default Gateway Setup  
6218-A2-GB23-00  
September 2005  
5-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
If you want to specify the default gateway address, then uncheck the box as seen  
below. Enter the default gateway address and, optionally, the WAN interface you  
will use. Click on Save / Apply to save the settings.  
If you add or change the default gateway address, you must reboot the router to  
put the new default gateway IP address into effect.  
Figure 5-28. Default Gateway Setup  
Routing – Static Route  
Use the Routing - Static Route screen to add a static route to the routing table.  
Figure 5-29. Static Route Setup  
5-18  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
Enter the route information and click on Save/Apply to make it active. No reboot is  
required.  
Figure 5-30. Static Route Add  
Routing – RIP  
If RIP is enabled, the router operation can be configured as Active or Passive.  
Figure 5-31. RIP Setup  
6218-A2-GB23-00  
September 2005  
5-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
DNS Server  
Use the DNS Server screen to request automatic assignment of a DNS or to  
specify a primary and secondary DNS.  
Figure 5-32. DNS Setup  
Dynamic DNS  
Use the Dynamic DNS screen to alias a dynamic IP address to a static hostname,  
allowing your router to be easily accessed from anywhere on the Internet.  
Figure 5-33. Dynamic DNS  
5-20  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
5. Advanced Setup  
To set up a Dynamic DNS entry:  
1. Click on Add. The Add Dynamic DNS screen appears.  
Figure 5-34. Adding a Dynamic DNS Entry  
2. Select a D-DNS Provider from the drop-down list.  
3. Enter the Hostname you have selected for the interface.  
4. Select the router Interface from the drop-down list.  
5. Enter the information you used to register with the dynamic DNS service: for  
DynDNS, enter your Username and Password; for TOZ, enter your E-mail  
address and Key.  
6. Click on Save/Apply.  
6218-A2-GB23-00  
September 2005  
5-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Advanced Setup  
ADSL  
There are three major items in the ADSL settings.  
Figure 5-35. DSL Settings  
Modulation Methods  
The following modulation methods are supported by the 6218 wireless router:  
„
„
„
„
„
„
G.dmt Enabled  
G.lite Enabled  
T1.413 Enabled  
ADSL Enabled  
Annex L Enabled  
ADSL2+ Enabled.  
Do not change this setting unless so directed by your ISP.  
Phone Line Pair  
The 6218 wireless router supports phone lines on pins 2 and 3 or pins 1 and 4 to  
connect your ADSL line. If your phone system uses pins 2 and 3, attach a normal  
RJ11 cable to the router and select "Inner pair" on the screen; if your phone  
system uses pins 1 and 4, attach the phone with the supplied RJ11 cable and  
select "Outer pair" on the screen.  
5-22  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
5. Advanced Setup  
Capability  
The following are included under Capability:  
„
„
Bitswap Enable  
SRA (Seamless Rate Adaptation) Enable  
Do not change these settings unless so directed by your ISP.  
DSL Advanced Settings  
Do not change the DSL Advanced Settings unless so directed by your ISP. To view  
the DSL Advanced Settings screen, click on the Advanced Settings button on the  
DSL Settings screen (see Figure 5-35).  
Figure 5-36. DSL Advanced Settings  
There are five test modes between the router and your ISP:  
„
„
„
Normal test: Puts the router in a test mode in which it only sends a Normal  
signal.  
Reverb test: Puts the router in a test mode in which it only sends a Reverb  
signal.  
Medley test: Puts the router in a test mode in which it only sends a Medley  
signal.  
6218-A2-GB23-00  
September 2005  
5-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
5. Advanced Setup  
„
„
No Retrain: In this mode the router will try to establish a connection as in  
normal mode, but once the connection is up it will not retrain if the signal is  
lost.  
L3: Puts the router into the L3 power state.  
Select a test mode and click on Apply. Then click on Tone Selection.  
Tone Selection  
To view the ADSL Tone Settings screen, click on the Tone Selection button of the  
DSL Advanced Settings screen (see Figure 5-36).  
The frequency band of ADSL is split up into 256 separate tones, each spaced  
4.3125 kHz apart. With each tone carrying separate data, the technique operates  
as if 256 separate modems were running in parallel. The tone range is from 0 to 31  
for upstream and from 32 to 255 for downstream.  
Do not change these settings unless so directed by your ISP.  
Figure 5-37. Tone Settings  
5-24  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
Wireless  
The Wireless screens let you configure the settings for wireless access, security,  
and protocols.  
Wireless - Basic  
The Wireless - Basic screen lets you enable or disable Wi-Fi capability in the  
router. The default setting for wireless is enabled. From this screen you can also  
hide the access point so others cannot see your ID on the network.  
Figure 5-38. Wireless – Basic  
Wireless - Security  
The next screen is the Wireless - Security screen which allows you to select the  
network authentication method and to enable or disable WEP encryption. Note  
that depending on the network authentication that is selected, the screen will  
change accordingly so additional fields can be configured for the specific  
authentication method.  
Network authentication methods include the following-  
„
„
Open – Anyone can access the network. The default is a disabled WEP  
encryption setting.  
Shared – WEP encryption is enabled and encryption key strength of 64-bit or  
128-bit needs to be selected. Click on Set Encryption Keys to manually set the  
network encryption keys. Up to 4 different keys can be set and you can come  
back to select which one to use at any time.  
„
802.1X – Requires mutual authentication between a client station and the  
router by including a RADIUS-based authentication server. Information about  
the RADIUS server such as its IP address, port and key must be entered.  
6218-A2-GB23-00  
September 2005  
5-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
5. Advanced Setup  
WEP encryption is also enabled and the encryption strength must also be  
selected.  
„
„
„
WPA (Wi-Fi Protected Access) – Usually used for the larger enterprise  
environment, it uses a RADIUS server and TKIP (Temporal Key Integrity  
Protocol) encryption (instead of WEP encryption, which is disabled). TKIP  
uses 128-bit dynamic session keys (per user, per session, and per packet  
keys).  
WPA-PSK (Wi-Fi Protected Access - Pre-Shared Key) – WPA for home and  
SOHO environments using the same strong TKIP encryption, per-packet key  
construction, and key management that WPA provides in the enterprise  
environment. The main difference is that the password is entered manually. A  
Group Re-Key Interval time is also required.  
WPA2 (Wi-Fi Protected Access 2) – Second generation of WPA, which uses  
AES (Advanced Encryption Standard) instead of TKIP as its encryption  
method. Network Re-Auth Interval is the time in which another key needs to be  
dynamically issued.  
„
„
WPA2-PSK (Wi-Fi Protected Access 2 - Pre-Shared Key) – Suitable for home  
and SOHO environments, WPA2-PSK uses AES encryption and requires you  
to enter a password and a re-key interval time.  
Mixed WPA2 / WPA – During transitional times for upgrades in the enterprise  
environment, this mixed authentication method allows upgraded users and  
users not yet upgraded to access the network via the router. RADIUS server  
information must be entered for WPA as well as a group re-key interval time.  
Both TKIP and AES are used.  
„
Mixed WPA2 / WPA-PSK – Useful during transitional times for upgrades in the  
home or SOHO environment, a pre-shared key must be entered along with the  
group re-key interval time. Both TKIP and AES are also used.  
Figure 5-39. Wireless – Security  
5-26  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Advanced Setup  
Wireless - MAC Filter  
The MAC filter screen allows you to manage MAC address filters. Add the MAC  
addresses that you want to manage and then select the mode that you want to use  
to manage them. You can disable this feature or you can allow or deny access to  
the MAC addresses that you add to the list.  
Figure 5-40. Wireless – MAC Filter  
The following screen appears when you want to add a MAC address to the filter.  
Enter a MAC address in the form xx-xx-xx-xx-xx-xx where each xx is a two-digit  
hexadecimal number (for example, 00-05-13-ba-c8-01), then click on the Save /  
Apply button.  
Figure 5-41. Wireless – MAC Filter Add  
6218-A2-GB23-00  
September 2005  
5-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Advanced Setup  
Wireless - Bridge  
The Wireless - Bridge screen lets you determine whether the router acts as an  
access point or a wireless bridge.  
Figure 5-42. Wireless – Bridge  
Wireless - Advanced  
The Wireless - Advanced screen lets you configure advanced features of the  
wireless LAN network:  
„
AP Isolation – If you select enable, then each of your wireless clients will not  
be able to communicate with each other.  
„
„
Band – The default setting is 2.4GHz - 802.11g  
Channel – 802.11b and 802.11g use channels to limit interference from other  
devices. If you are experiencing interference with another 2.4 Ghz device such  
as a baby monitor, security alarm, or cordless phone, then change the channel  
on your router.  
„
„
„
„
Multicast Rate – The rate at which a message is sent to a specified group of  
recipients.  
Basic Rate – The set of data transfer rates that all the stations will be capable  
of using to receive frames from a wireless medium.  
Fragmentation Threshold – Used to fragment packets which help improve  
performance in the presence of radio frequency (RF) interference.  
RTS Threshold (Request to Send Threshold) – Determines the packet size of  
a transmission through the use of the router to help control traffic flow.  
„
„
DTIM Interval – Sets the Wake-up interval for clients in power-saving mode.  
Beacon Interval – A packet of information that is sent from a connected device  
to all other devices where it announces its availability and readiness. A beacon  
interval is a period of time (sent with the beacon) before sending the beacon  
again. The beacon interval may be adjusted in milliseconds (ms).  
5-28  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Advanced Setup  
„
Xpress Technology – A technology that utilizes standards based on  
framebursting to achieve higher throughput. With Xpress Technology enabled,  
aggregate throughput (the sum of the individual throughput speeds of each  
client on the network) can improve by up to 25 percent in 802.11g only  
networks and up to 75 percent in mixed networks comprising 802.11g and  
802.11b equipment.  
„
„
54g Mode – 54g is a proprietary Wi-Fi technology that provides higher speed,  
reach, and security.  
54g Protection – The 802.11g standards provide a protection method so  
802.11g and 802.11b devices can co-exist in the same network without  
"speaking" at the same time. Do not disable 54g Protection if there is a  
possibility that a 802.11b device may need to use your wireless network. In  
Auto Mode, the wireless device will use RTS/CTS (Request to Send / Clear to  
Send) to improve 802.11g performance in mixed 802.11g/802.11b networks.  
Turn protection off to maximize 802.11g throughput under most conditions.  
„
WMM (Wi-Fi Multimedia) – WMM provides QoS functionality for Wi-Fi  
multimedia applications by prioritizing traffic demands from different  
applications on the network.  
Figure 5-43. Wireless – Advanced  
6218-A2-GB23-00  
September 2005  
5-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Advanced Setup  
5-30  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Diagnostics  
6
Testing the DSL Connection  
The diagnostics screen allows you to run diagnostic tests to check your DSL  
connection. The screen shows test results for three connections:  
„
„
„
Connection to your local network  
Connection to your DSL service provider  
Connection to your Internet service provider  
Use the Test and Test with OAM F4 buttons to retest if necessary.  
Figure 6-1. Diagnostics  
6218-A2-GB23-00  
September 2005  
6-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
6. Diagnostics  
6-2  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Management  
7
Saving and Restoring the Configuration  
The configuration of your router can be backed up to a file, and also can be  
restored from a file. You can also restore the router to its factory default  
configuration.  
Backing Up Configuration Settings  
To back up your settings, select Management -> Settings -> Backup Settings.  
Figure 7-1. Back Up Settings Screen  
6218-A2-GB23-00  
September 2005  
7-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
7. Management  
Verify that you would like to save the file.  
Figure 7-2. Backup Settings Upload Confirmation  
Select the location where you want to save the file.  
Figure 7-3. Backup Settings File Location  
7-2  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Management  
Restoring Configuration Settings  
To restore saved settings, select Management -> Settings -> Restore User  
Settings.  
Figure 7-4. Restore User Settings Screen  
Select the backup file you want to restore and click on Update Settings.  
Figure 7-5. Restore Settings File Location  
6218-A2-GB23-00  
September 2005  
7-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Management  
The router will restore settings and reboot to activate the restored settings.  
Figure 7-6. Upload in Progress Screen  
7-4  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Management  
Restoring Default Settings  
Restore Default will erase all current settings and restore the router to factory  
default settings.  
To restore the router to factory default settings, select Management -> Settings ->  
Restore Default.  
Figure 7-7. Restore Default Settings Screen  
Reply OK to the confirmation dialog.  
Figure 7-8. Restore Default Confirmation Dialog  
6218-A2-GB23-00  
September 2005  
7-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Management  
The router will restore the default settings and reboot.  
Figure 7-9. Restore Default Settings Reboot  
System Log  
The System Log dialog allows you to view the System Log and configure the  
System Log options.  
Figure 7-10. System Log  
7-6  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Management  
View System Log  
Click on the "View System Log" button to check the log file.  
Figure 7-11. View System Log  
6218-A2-GB23-00  
September 2005  
7-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Management  
Configure System Log  
If the log is enabled, the system will log selected events: Emergency, Alert, Critical,  
Error, Warning, Notice, Informational, and Debugging. All events above or equal to  
the selected log levels will be logged (maintained in the system log file) and  
displayed.  
If the selected mode is Remote or Both, events will be sent to the specified IP  
address and UDP port of a remote system log server. If the selected mode is Local  
or Both, events will be recorded in the local memory.  
Figure 7-12. System Log Configuration  
Select the desired values and click on the "Save/Apply" button to configure the  
system log options.  
7-8  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Management  
SNMP  
Simple Network Management Protocol (SNMP) allows a management application  
to retrieve statistics and status from the SNMP agent in the router. Use the SNMP  
screen to set up parameters for SNMP access.  
Figure 7-13. SNMP Screen  
Select the desired values and click on Save/Apply to configure the SNMP options.  
6218-A2-GB23-00  
September 2005  
7-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Management  
Internet Time  
Use the Internet Time screen to specify whether the router uses Simple Network  
Time Protocol (SNTP) to obtain the time of day from NTP servers on the Internet.  
To set up the router to obtain time from an NTP server:  
1. Select “Automatically synchronize with Internet time servers”. The SNTP fields  
appear.  
Figure 7-14. Internet Time Screen  
2. Select NTP servers.  
3. Specify the time zone offset for your router’s location.  
4. Click on Save/Apply.  
7-10  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Management  
Access Control – Services  
You can enable or disable some services of your router by LAN or WAN. If no WAN  
connection is defined, only the LAN side can be configured.  
Figure 7-15. Services Setup  
Access Control – IP Addresses  
Web access to the router can be limited when Access Control Mode is enabled.  
The IP addresses of allowed hosts can be added using Access Control -> IP  
Address.  
Figure 7-16. IP Address Setup  
6218-A2-GB23-00  
September 2005  
7-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
7. Management  
To assign the IP address of the management station that is permitted to access  
the local management services, enter the IP address in the box and click on the  
Save/Apply button.  
Figure 7-17. Access Control – IP Address Add Screen  
Access Control – Passwords  
Use Access Control -> Passwords to change a password. Select an account and  
enter the current password and the new password. Then click on Save/Apply.  
Figure 7-18. Access Control – Passwords Screen  
7-12  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Management  
Update Software  
If your ISP releases new software for this router, follow these steps to perform an  
upgrade.  
1. Obtain an updated software image file from your ISP.  
2. Enter the path to the image file location or click on the "Browse" button to  
locate the image file.  
3. Click on the Update Software button once to upload the new image file.  
Figure 7-19. Update Software  
Note  
The update process takes about two minutes to complete, and your router will  
reboot automatically.  
6218-A2-GB23-00  
September 2005  
7-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Management  
Reboot Router  
Select Management -> Reboot Router to reboot the router using the web interface.  
The router will save the current configuration and reboot itself using the new  
configuration. The rebooting process takes about two minutes to complete.  
Figure 7-20. Reboot Router Screen  
7-14  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Specifications  
A
Specifications are subject to change without notice.  
Table A-1. 6218-I1 Specifications  
Specification  
Criteria  
DSL Protocol Support  
ANSI T1.413 (Full Rate ADSL)  
ITU G.992.1 (DMT)  
ITU G.992.2 (G.lite)  
ITU G.992.3 (ADSL2)  
ITU G.992.5 (ADSL2+)  
ITU G.994.1 (G.hs)  
ITU G.997.1  
Environment  
Interfaces  
Power  
Operating Temperature: 32° F to 104° F (0° C to 40° C)  
Storage Temperature: –4° F to 149° F (–20° C to 65° C)  
Humidity: 5% to 95%, non-condensing  
DSL Line: RJ11  
Ethernet: 10/100BaseT, RJ45  
Wireless: 802.11b, 802.11g  
100 VAC, 50 Hz  
110 VAC, 60 Hz  
220 VAC, 50/60 Hz  
Size  
1.2" High x 6.5" Wide x 4.4" Deep  
(3.0 cm High x 16.5 cm Wide x 11.2 cm Deep)  
Weight (Shipping)  
1.5 lbs (0.7 kg)  
6218-A2-GB23-00  
September 2005  
A-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
A. Specifications  
A-2  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
Document  
Feedback, A  
Purpose and Intended Audience, v  
Summary, v  
Domain Name Server, 5-20  
Dynamic DNS, 5-20  
A
About This Guide, v  
Access Control  
IP Addresses, 7-11  
Passwords, 7-12  
Services, 7-11  
ADSL, 5-22  
E
BER Test, 3-5  
Statistics, 3-4  
EMI Notice  
Canada, D  
Japan, D  
Environment, A-1  
Ethernet  
Advanced Settings, DSL, 5-23  
Advanced Setup, 5-1  
ARP, 3-6  
ATM  
PVC Configuration, 5-2  
Statistics, 3-4  
cable, 2-2  
F
B
FCC Part 15 Declaration, B  
Features, 1-1  
Backing Up Configuration Settings, 7-1  
BER Test, 3-5  
Firewall, 5-11  
Bridge Service, 5-4  
Bridging groups, 5-15  
MAC Filtering, 5-13  
Firmware Update, 7-13  
Front Panel, 1-3  
C
G
Cables, Installing, 2-2  
Capability, 5-23  
CE Marking, B  
Gateway, Default, 5-17  
Configuring  
H
PC, 2-4  
Hardware  
System Log, 7-8  
Connecting Hardware, 2-2  
Connection Type, 5-3  
Connections, 2-2  
Installation, 2-1  
I
D
Important Safety Instructions, B  
Installing hardware, 2-2  
Interfaces, A-1  
Default Gateway, 5-17  
Default IP Address, 2-4  
Definitions, 1-1  
Internet Time, 7-10  
Introduction, 1-1  
IP Address  
Device Information, 3-1  
Diagnostics, 6-1  
Dimensions, A-1  
DMZ Host, 5-10  
DNS, 5-20  
Access Control, 7-11  
Of Router, 2-4  
IP Filtering  
Dynamic, 5-20  
Incoming, 5-12  
Outgoing, 5-11  
6218-A2-GB23-00  
September 2005  
IN-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Index  
J
R
Japan Notices, D  
Rear Panel, 1-4  
Reboot Router, 7-14  
Restoring  
L
Configuration Settings, 7-3  
Default Settings, 7-5  
RIP, 5-19  
Route status, 3-6  
Routing  
Local Area Network (LAN)  
ports, connecting, 2-2  
Setup, 5-6  
Statistics, 3-3  
Logging In, 3-1  
Default Gateway, 5-17  
RIP, 5-19  
Static Route, 5-18  
M
MAC Filtering, 5-13  
Management, 7-1  
S
Mapping ports, 5-15  
Modulation Methods, 5-22  
Sales, Service, and Training Information, A  
Saving and Restoring Configuration, 7-1  
Services, Access Control, 7-11  
Shipping Weight, A-1  
Size, A-1  
N
NAT, 5-7  
Network Interface Card, 2-2  
SNTP, 7-10  
Notice  
Specifications, A-1  
Static Route, 5-18  
Statistics  
to Users of the Canadian Telephone Network, D  
to Users of the United States Telephone Network, C  
ADSL, 3-4  
ATM, 3-4  
LAN, 3-3  
WAN, 3-3  
O
Operating Environment, A-1  
Status  
P
ARP, 3-6  
Route, 3-6  
Parts List, 1-2  
Password  
Summary, 3-1  
Access Control, 7-12  
Default, 2-10  
PC Setup, 2-1  
Phone Line Pair, 5-22  
Port Mapping, 5-15  
Port Triggering, 5-9  
Power  
Specifications, A-1  
Supply, 2-2  
Product-Related Documents, vi  
Protocols Supported, A-1  
PVC  
WAN, 3-2  
System Log, 7-6  
Configuring, 7-8  
System Requirements, 1-2  
T
Test  
BER, 3-5  
DSL Connection, 6-1  
Time, 7-10  
Tone Selection, 5-24  
Trademarks, A  
Adding, 5-2  
Configuring, 5-2  
Detecting, 4-1  
U
Update Software, 7-13  
User Name, Default, 2-10  
Q
Quality of Service, 5-4, 5-16  
Quick Setup, 4-1  
V
View System Log, 7-7  
Virtual Servers, 5-7  
IN-2  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
Weight, A-1  
W
Windows 2000, 2-7  
Windows 95, 2-8  
Windows 98, 2-8  
Windows ME, 2-7  
Windows NT, 2-9  
Windows XP, 2-5  
WAN, 3-2, 5-1  
Setup, 5-4  
Statistics, 3-3  
Status, 3-2  
Warranty, A  
Web Interface  
Home Page, 2-11  
Using, 3-1  
6218-A2-GB23-00  
September 2005  
IN-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
IN-4  
September 2005  
6218-A2-GB23-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Murphy Switch Series LM300 User Manual
National Instruments Switch SCC RLY01 User Manual
NextBase Portable DVD Player SDV185 SD User Manual
Nikon DVR DX TL5716E User Manual
Niles Audio Stereo Amplifier SI 1650 User Manual
NordicTrack Treadmill NTL778061 User Manual
Olympus Microcassette Recorder WS400S User Manual
Onkyo DVD Player DV SP402E User Manual
Palsonic CRT Television 6830TG User Manual
ParaBody Home Gym 876101 User Manual