435104 LEG PRESS ADAPTER KIT
ASSEMBLY INSTRUCTIONS
Part # 6865101
1
Revision: 2/15/00
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY PART #
DESCRIPTION
FRONTLEG
QTY
KEY PART #
DESCRIPTION
3/8” HEX NUT
3/8” WASHER
3/8” LOCKNUT
1/2” WASHER
1/2” LOCKNUT
3/8 X 2-1/4” BOLT
1/2 X 3” BOLT
3/8 X 1”
QTY
1
2
3
4
5
6
7
8
6747603
3116202
3108102
6427101
3118701
3201501
6271801
6747901
1
2
1
1
1
1
1
1
9
3102701
3102501
3102802
3102502
3102801
3102902
3102910
3102909
2
3
2
4
4
2
4
1
3-1/2”PULLEY
10
11
12
13
14
15
16
QUICKDISCONNECTLINK
KEYHOLECLEVIS
2”PULLEY
SWIVEL SNAP
72”ELASTIC CORD
LEGPRESSCABLE
NOTE: The LEGPRESSATTACHTMENT (832101) must be assembled before connecting it to the
PARABODY425104 HOME GYM
3/8” X 1” BUTTON
HEAD CAP SCREW
REAR SHROUD
3/8” X 1” BUTTON
HEAD CAP SCREW
FIGURE 1
STEP 1
• REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the rear SHROUD. Remove the SHROUD from the 425104 HOME
GYM. See FIGURE 1.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR
SHROUD
FIGURE 2
STEP 2
• If the 445104 SECOND STACK OPTION is not installed, the rear SHROUD opening must be removed.Apply pressure to the bottom
of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the SHROUD as shown in FIGURE 2.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ELASTIC CORD
BASE
HEXNUT
3/8” LOCK NUT
SWIVEL SNAP
3/8” THREADED SHAFT
3/8 X 1/2”
SPACERS
(DISCARD)
3/8” LOCK NUT
HEXNUT
SWIVEL SNAP
FIGURE 3
STEP 3
• Remove two 3/8” LOCK NUTS, two 3/8” HEX NUTS, two SWIVEL SNAP (68) (keep elastic cords attached), two
3/8 X 1/2” SPACERS, and one 3/8” THREADED SHAFT from the bracket on the BASE as shown in FIGURE 3.
• Discard the two 3/8 X 1/2” SPACERS.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 4
BASE
HEXNUT
3/8” LOCK NUT
SWIVEL SNAP
3/8” THREADED SHAFT
2
3/8” LOCK NUT
HEXNUT
SWIVEL SNAP
STEP 4
• Assemble the two previously removed 3/8” HEX NUTS, two previously removed SWIVEL SNAPS, one 3-1/2” PULLEY (2), and two
previously removed 3/8” LOCK NUTS to the previously removed 3/8” THREADED SHAFT as shown in FIGURE 4.
3/8” X 2” BOLT
BASE
3/8” WASHER
4-1/2” PULLEY
2-7/8” L-BRACKET
3/8” WASHER
3/8” LOCK NUT
FIGURE 5
STEP 5
• Remove one 3/8 X 2” BOLT, two 3/8” WASHERS, one 2-7/8” L-BRACKET, one 4-1/2” PULLEY, and one 3/8” LOCK NUT from the
upper flat on the BASE as shown in FIGURE 5.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
14 3/8 X 2-1/4”
3/8” WASHER
BASE
3/8” WASHER
6
4-1/2” PULLEY
2-7/8” L-BRACKET
9 HEXNUT
3/8” LOCK NUT
FIGURE 6
STEP 6
• SECURELY assemble the previously removed 4-1/2” PULLEY to the BASE using one 3/8 X 2-1/4” BOLT (14), two previously
removed 3/8” WASHERS, one previously removed 2-7/8” L-BRACKET, one SWIVEL SNAP(6), one 3/8” HEX NUT (9), and one
previously removed 3/8” LOCK NUT. See FIGURE 6.
TOP BOOM
9 3/8” HEX NUT
FIGURE 7A
(WITHOUT
445104 SECOND
3/8” WASHER
5
3/8” LOCK NUT
STACK OPTION)
STEP 7A
• If the 445104 SECOND STACK OPTION is installed follow STEP7B .
• Remove one 3/8” WASHER and one 3/8” LOCK NUT from the 3/8” THREADED SHAFT on the TOPBOOM.
• SECURELY assemble one 2” PULLEY(5) to the 3/8” THREADED SHAFT on the TOPBOOM using one previously installed 3/8”
WASHER, one 3/8” HEX NUT (9) and one previously installed 3/8” LOCK NUT as shown in FIGURE 7A.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TOP BOOM
3/8” X 1” 16
10
FIGURE 7B (WITH
445104 SECOND
STACK OPTION)
5
11 3/8” LOCK NUT
STEP 7B
• If the 445104 SECOND STACK OPTION is NOT installed proceed to STEP 8 .
• SECURELYassemble one 3/8 X 1” BOLT (16), one 3/8” WASHER (10), one 2” PULLEY(5) and one 3/8” LOCK NUT (11) to the
bracket on the TOP BOOM as shown in FIGURE 7B.
STEP 8
2
• SECURELY attach one 3-1/2” PULLEY (2) to the FRONT
LEG (1) using one 3/8 X 2-1/4” BOLT (14), two 3/8”WASH-
ERS (10), and one 3/8” LOCK NUT (11). See FIGURE 8.
3/8 X 2-1/4” 14
10
1
• Attach the open end of PRESS LINK CABLE (8) to the
QUICK DISCONNECT LINK (3). See FIGURE 8.
• SECURELY tighten the QUICK DISCONNECT (3) to the
tab on the FRONT LEG (1) as shown in FIGURE 8.
10
11
SECURELY
TIGHTEN!
3
8
FIGURE 8
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1/2 X 3” 15
12
8
1
13
LEGPRESS
FIGURE 9
STEP 9
• SECURELYattach the LEG PRESS to the FRONT LEG (1) using two 1/2” X 3” BOLTS (15), two 1/2” WASHERS (12), and two 1/2”
LOCK NUTS (13). See FIGURE 9.
• Route LEG PRESS CABLE (8) around the 3-1/2” PULLEY on the LEG PRESS and UNDER the 3-1/2” PULLEY on the FRONT LEG (1)
as shown in FIGURE 9.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE
8
1
12
13
1/2 X 3” 15
FIGURE 10
STEP 10
• SECURELYattach the FRONTLEG (1) to 425 BASE using two 1/2 X 3” BOLTS (15), two 1/2”WASHERS (12) and two 1/2” LOCK NUTS
(13). See FIGURE 10.
• Route LEG PRESS CABLE (8) under the 3-1/2” PULLEY on the 425 BASE as shown in FIGURE 10.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 11
DETAIL 11
4
LEG
PRESS
CABLE
8
LEG
CABLE
SEE DETAIL11
PRESS
CABLE
LAT
CABLE
D-RING
STEP11
• Run the LEG PRESS CABLE through the correct hole on the d-ring and attach one KEYHOLE CLEVIS to the end of the LEG PRESS
CABLE. See FIGURE 11 & DETAIL11. (NOTE: If the 445101 SECOND STACK kit is installed, evenly space the LAT& LEGEXT.
CABLES on the D-RING)
7
STEP 12
• Assemble one 72” ELASTIC CORD (7) to the KEYHOLE CLEVIS (4)
as shown in FIGURE 12.
4
LEGPRESSCABLE
8
FIGURE 12
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TOP BOOM
5
7
8
LEGPRESSCABLE
FIGURE 12
STEP 12
• Assemble the 72” ELASTIC CORD (7) from the LEG PRESS CABLE (8) around the 2” PULLEY (5) in the TOP BOOM as shown in
FIGURE12.
FIGURE 13
STEP 13
• Assemble the ELASTIC CORD(7)
from the LEG PRESS CABLE to the
corresponding SWIVEL SNAP (6) on
the BASE as shown in FIGURE 13.
7
6
BASE
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3/8” X 1” BUTTON
HEAD CAP SCREW
REAR SHROUD
3/8” X 1” BUTTON
HEAD CAP SCREW
SPRING PIN ADJUSTMENT
FIGURE 14
STEP 14
• SECURELYattach the four previously removed 3/8 X 1” BUTTON HEAD CAPSCREWS to the rear SHROUD. See FIGURE 14.
• The 832 LEG PRESS is equipped with a spring pin adjustment to accommodate different sized users and allow easy entry and exit
from the machine. To use, you must slightly push against the foot plates to take tension off the pin.
Thank you for purchasing the Parabody 435104 Leg Press Adapter Kit. If unsure of proper use of equipment,
call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|