Panasonic Computer Monitor CQ VX100W User Manual
In-dash 7"Widescreen Color LCD Monitor/DVD Receiver  
인대쉬 7" 와이드스크린 컬러 LCD 모니터/DVD 리시버  
7-‰˛ÈÏÓ‚˚È ‡‚ÚÓÏÓ·ËθÌ˚È ¯ËÓÍÓ˝Í‡ÌÌ˚È ˆ‚ÂÚÌÓÈ Üä-ÏÓÌËÚÓ/DVD-ÂÒË‚Â  
DIMMER  
TILT  
CLOSE  
IN-DASH 7" WIDESCREEN COLOR LCD MONITOR DVD RECEIVER  
/
Model:  
CQ-VX100W  
CQ-VX100W  
TEXT  
AV1 IN  
TUNE/TRACK  
VOL  
POWER  
PUSH SEL  
MUTE  
MAP  
SOURCE  
TEXT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
❑
❑
Take care not to damage the leads.  
Caution  
When wiring, take care not to damage the leads. Prevent  
them from getting caught in the vehicle chassis, screws,  
and moving parts such as seat rails. Do not scratch, pull,  
bend or twist the leads. Do not run them near heat sources  
or place heavy objects on them. If leads must be run over  
sharp metal edges, protect the leads by winding them with  
vinyl tape or similar protection.  
Observe the following cautions when using this  
unit.  
Keep the sound volume at an appropriate level.  
Keep the volume level low enough to be aware of road and  
traffic conditions while driving.  
Do not insert or allow your hand or fingers to be  
caught in the unit.  
To prevent injury, do not get your hand or fingers caught in  
moving parts or in the disc slot. Especially watch out for  
infants.  
This unit is designed for use exclusively in auto-  
mobiles.  
Do not operate the unit for a prolonged period with  
the engine turned off.  
Operating the audio system for a long period of time with  
the engine turned off will drain the battery.  
Do not expose the unit to direct sunlight or exces-  
sive heat.  
Otherwise these will raise the interior temperature of the  
unit, and it may lead to smoke, fire, or other damage to the  
unit.  
Do not use the product where it will be exposed to  
water, moisture, or dust.  
Exposure of the unit to water, moisture, or dust may lead  
to smoke, fire, or other damage to the unit. Make especially  
sure that the unit does not get wet in car washes or on  
rainy days.  
2
❑
Use the designated parts and tools for installation.  
Use the supplied or designated parts and appropriate tools  
to install the product. The use of parts other than those  
supplied or designated may result in internal damage to the  
unit. Faulty installation may lead to an accident, a malfunc-  
tion or fire.  
Do not block the air vent or the cooling plate of the  
unit.  
Blocking these parts will cause the interior of the unit to  
overheat and will result in fire or other damage.  
Do not install the product where it is exposed to  
strong vibrations or is unstable.  
Avoid slanted or strongly curved surfaces for installation. If  
the installation is not stable, the unit may fall down while  
driving and this can lead to an accident or injury.  
❑
❑
❑
❑
❑
❑
❑
❑
Installation Angle  
The product should be installed in a horizontal position  
with the front end up at a convenient angle, but not more  
than 30˚.  
The user should bear in mind that in some areas there may  
be restrictions on how and where this unit must be  
installed. Consult your dealer for further details.  
Wear gloves for safety. Make sure that wiring is  
completed before installation.  
To prevent damage to the unit, do not connect the  
power connector until the whole wiring is complet-  
ed.  
Do not connect more than one speaker to one set  
of speaker leads. (except for connecting to a  
tweeter)  
❑
❑
❑
Set the volume level to low enough before the AUX  
connection is completed.  
Failure to observe this, the loud noise may come out and  
damage your speakers and your hearing. Direct connection  
of the speaker/headphone output of an external device  
without any attenuator may distort sound or damage the  
connected external device.  
❑
Observe the following cautions when installing.  
Refer wiring and installation to qualified service  
personnel.  
❑
Installation of this unit requires special skills and experi-  
ence. For maximum safety, have it installed by your dealer.  
Panasonic is not liable for any problems resulting from  
your own installation of the unit.  
❑
Follow the instructions to install and wire the prod-  
uct.  
Not following the instructions to properly install and wire  
the product could cause an accident or fire.  
CAUTION:  
• PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR WIRING,  
INSTALLATION, AND USE OF THIS UNIT AND THE DEVICES TO BE CONNECTED.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
CQ-VX100W  
Safety Information (continued)  
Caution  
THIS PRODUCT IS A CLASS I LASER PRODUCT.  
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE  
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN  
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.  
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOUR-  
SELF. REFER SERVICING TO QUALIFIED PERSONNEL.  
3
This system is designed so that you  
cannot see moving pictures while  
you are driving.  
Park your car in a safe place and pull the side  
brake (parking brake) lever before watching the  
monitor.  
¡
A rear monitor (option) displays moving pic-  
¡
tures while driving.  
Note:  
¡Be sure to connect the side brake (parking  
brake) connection lead. (aInstallation  
Instructions)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
CQ-VX100W  
Notes on Use  
Liquid Crystal Panel  
¡Do not cause impact to the liquid crystal panel.  
¡Usage temperature range: 0 °C to 40 °C  
When the temperature is very cold or very hot, the  
image may not appear clearly or may move slowly.  
Also, movement of the image may seem to be out of  
synchronization or the image quality may decline in  
such environments. Note that this is not a malfunction  
or problem.  
¡Sudden changes in the temperature inside the car such  
as those which occur immediately after the car’s air  
conditioner or heater has been turned on may cause  
the inside of the liquid crystal panel to cloud over due  
to water vapor or it may cause condensation (droplets  
of water) to form and, as a result, the panel may not  
work properly. Do not use the unit while these symp-  
toms are in evidence but leave the unit standing for  
about and hour, and then resume or start use  
4
¡In order to protect the liquid crystal panel, keep it out  
of direct sunlight while the unit is not in use.  
Before Reading These Instructions  
Differences Among 3 Models  
This operating instruction manual is for 3 models CQ-VX100W2/CQ-VX100W3 and  
CQ-VX100W5.  
Example:  
The following table shows the playable region number for each model.  
2
3
5
Model  
Playable region number  
2 (ALL)  
CQ-VX100W2  
CQ-VX100W3  
CQ-VX100W5  
2 3  
4 5  
ALL  
3 (ALL)  
5 (ALL)  
“Before Disc Playback”  
(apage 16)  
Components  
DIMMER  
TILT  
CLOSE  
IN-DASH 7" WIDESCREEN COLOR LCD MONITOR DVD RECEIVER  
/
1. Main Unit  
(LCD monitor/DVD player)  
5. Installation Hardware (screws,  
cords, etc.)  
(aInstallation Instructions)  
CQ-VX100W  
TEXT  
I
I
I
A
V
1
IN  
Qty.: 1  
VOL  
POWER  
TUNE/TRACK  
P
U
S
H
S
E
L
MUTE  
MAP  
SOURCE  
XXXXXXXXXXXXXXX  
XXXXXXXXXXXXXXXXX  
XXXXXXXXXXXXXX  
XXXXXXXXXXXXXXXX  
OO-OOOOO  
2. Operating Instructions  
<YFM264C059CA>  
Note:  
¡The number in parenthesis underneath each accessory  
part name is the part number for maintenance and  
service.  
¡Accessories and their parts numbers are subject to  
modification without prior notice due to improvements.  
Qty.: 1  
Qty.: 1  
Qty.: 1  
XXXXXXXXXXXXXXX  
XXXXXXXXXXXXXXXXX  
XXXXXXXXXXXXXX  
XXXXXXXXXXXXXXXX  
OO-OOOOO  
3. System Upgrade Guidebook  
<YFM264C060CA>  
XXXXXXXXXXXXXXX  
XXXXXXXXXXXXXXXXX  
XXXXXXXXXXXXXX  
XXXXXXXXXXXXXXXX  
OO-OOOOO  
4. Installation Instructions  
<YFM294C125CA>  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
CQ-VX100W  
Features  
Panasonic welcomes you to our constantly growing family of electronic products owners.  
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully  
selected components, and assembled by people who are proud of the reputation their work has built for our company.  
We know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability  
we have built into it, you too will be proud to be a member of our family.  
5
Please refer to the separate “System Upgrade Guidebook” for how to operate this unit when optional devices are  
connected.  
■ No device is connected to this unit. aBasic operations are covered only by this book.  
■ Optional devices are connected to this unit. aRefer to the “System Upgrade Guidebook” in addition.  
■ Simultaneous Multi-Device Connection  
(with Expansion Module (hub unit))  
You can connect the optional Expansion Module (hub  
unit) (CY-EM100N). Connection of the Expansion  
Module allows you to simultaneously connect  
optional devices mentioned before as well as other  
AV devices. For details, refer to the operating instruc-  
tions for the Expansion Module.  
■ GUI (Graphic User Interface)  
GUI displays various indications with colorful sym-  
bols to enhance visibility, enjoyment, and operability.  
■ Disc type auto-detection  
The signal auto-detection function of this unit allows  
users to be free from selection between PAL and  
NTSC before use of your discs. (For output signal,  
set TV Type . ( page 34))  
a
Connectable devices  
■ Touch Panel Operation  
¡CD/DVD changer (max. 1)  
¡iPod (max. 2)  
®
Simply touch the screen lightly to operate virtually all  
functions. Easy-to-use menus and icons let you  
“touch and choose” what you want, so you can start  
using your system from the very first day. That also  
means that while you drive, you can concentrate on  
the road.  
¡Hands Free Kit with Audio Streaming featuring  
®
Bluetooth technology (Bluetooth unit) (max. 1)  
¡TV tuner (max. 1)  
Note:  
¡Market conditions regarding optional devices vary  
with countries and regions. For further information,  
consult your dealer.  
¡If a non-Panasonic product is connected to this unit,  
we do not guarantee the operations of the product.  
■ DVD–R, DVD–RW Playback  
(
a
page 16, 42 for details)  
■ ID code  
4-digit ID code for increased security.  
■ Integration of the monitor, FM/AM radio,  
DVD Video/Video CD player and  
CD/MP3/DivX player  
Fill in the ID code memo (apage 40).  
■ Built-in AV Input/Output Terminals  
For more convenient connection and setup, all termi-  
nals are now provided on the unit itself.  
Note:  
¡If a non-Panasonic product is connected to this unit,  
we do not guarantee the operations of the product.  
■ SQ (Sound Quality)  
You have 6 preset modes (Flat, Rock, Pop, Vocal,  
Jazz, Club). You can customize your setting for these  
(except Flat) and save them for instant recall.  
SQ3 (3-Band Sound Quality)  
Center frequency and level are adjustable in each of 3  
bands. This lets you fine-tune sound quality for each  
genre to suit car-interior acoustics and your personal  
preferences. (apage 33)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
CQ-VX100W  
Contents  
English  
2
한국어  
46  
90  
êÛÒÒÍËÈ  
¢Safety Information.......................... 2  
¢Notes on Use................................................... 5  
¢Before Reading These Instructions .............. 5  
¢Components.................................................... 5  
¢Features........................................................... 6  
¢Preparation...................................... 8  
First time power on, other settings, symbols used in this manual  
¢Name of Controls and Functions ................ 10  
¢Anti-Theft System ......................................... 11  
¢Touch Panel Operation Overview................ 12  
¢General .......................................... 14  
Power on/power off, display open/close, source  
selection, volume, mute, tilt angle, folding down the  
display temporarily  
¢
¢
Before Disc Playback..................... 16  
Disc Player..................................... 18  
¢Notes on MP3/DivX ....................................... 22  
¢Radio.............................................. 24  
¢AV1/AV2 ......................................... 26  
¢Settings ......................................... 28  
Setup operation  
Basic setting, screen, sound, disc, radio  
¢About DivX VOD Content ............................. 36  
¢Troubleshooting ........................... 37  
¢Maintenance .................................................. 41  
¢Notes on Discs.............................................. 42  
¢Language Code List...................................... 43  
¢Definition of Terms ....................................... 44  
¢Specifications................................................ 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
CQ-VX100W  
Preparation  
First Time Power On  
Other Settings  
When the power of this unit is turned on for the first time,  
the following screen appears. Perform the settings in  
accordance with the specifications of the car on which  
this unit is mounted.  
Please refer to the separate “System Upgrade  
Guidebook” for how to operate this unit when option-  
al devices are connected.  
7
(basic settings) ( page 30)  
a
Basic Setting  
clock, ID code, input, memory clear, other  
(screen settings) ( page 32)  
a
Screen  
dimmer, display, aspect  
(sound settings) ( page 33)  
a
Sound  
SQ3, bass/treble, balance/fader  
(disc settings) ( page 34)  
a
Disc  
audio language, subtitle language, menu language, video  
setting, audio setting, DivX registration  
(radio settings) ( page 35)  
a
Radio  
FM setup  
On  
Off  
: sets to ON if your car has ACC position.  
: sets to OFF if your car has no ACC posi-  
tion.  
Note:  
¡
Refer to “Settings” ( page 28) for further information  
a
about operations, settings, and others of the menu  
screen.  
default:  
On  
Note:  
¡
For an ACC-equipped car, select ON. The following  
functions are available.  
The power is turned on automatically when inserting  
a disc or magazine.  
¡
You may need to set the following depending on the  
devices to be connected.  
Off selection disables turning on the power of the  
¡
main unit through the remote control.  
AV1/AV2 (Camcorder, VCR, etc.)  
Caution  
Adjust  
Input  
. ( page 31)  
¡
a
¡Be sure to select off when your car has no ACC  
position in the ignition switch. Failure to do this  
could cause the battery to go dead.  
Warning  
¡When you connect external devices to this unit, be  
sure to connect the side brake connection lead  
(aInstallation Instructions).  
OFF  
ACC  
IGN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
CQ-VX100W  
Symbols used in this manual  
Pictographs  
Disc Marks  
8
The following pictographs are used for the descriptions  
You can perform some operations of this unit in one or  
more methods with the touch panel or remote control.  
This book explains such operations in tabular form as fol-  
lows. Refer to the following for the pictographs located in  
the upper part of each table.  
of disc operation. (apage 17-21)  
DVD  
: DVD  
VCD  
: VCD (Video CD)  
CD : CD  
Compatible  
Discs  
MP3 : CD-Rs/RWs containing MP3 files  
DivX : CD-Rs/RWs or DVD-Rs/RWs containing DivX files  
Compatible types of disc  
The discs compatible with the targeted operation.  
Operation on the Touch Panel  
You can use the touch panel to perform the targeted  
operation. If the operation is not executable with the  
touch panel, “––” is displayed.  
Operation on the Main Unit  
You can use the Main Unit to perform the targeted opera-  
tion. If the operation is not executable with the Main Unit,  
“––” is displayed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
CQ-VX100W  
Name of Controls and Functions  
![TILT]  
DIMMER  
TILT  
CLOSE  
(Display Raised)  
o[OPEN] (CLOSE)  
IN-DASH 7" WIDESCREEN COLOR LCD MONITOR / DVD RECEIVER  
9
q[DIM] (DIMMER)  
Display  
Disc slot  
w[VOL]  
CQ-VX100W  
(PUSH SEL)  
TEXT  
iAV1 IN  
AV1 IN  
TUNE/TRACK  
POWER  
VOL  
PUSH SEL  
MUTE  
MAP  
SOURCE  
e[MUTE]  
u [u]  
r[MAP]  
t[SOURCE] (POWER)  
y[s] [d] (TUNE/TRACK)  
![TILT]  
(Display Closed)  
DIMMER  
TILT  
DIM  
OPEN  
o[OPEN] (CLOSE)  
CQ-VX100W  
TUNE/TRACK  
q[DIM] (DIMMER)  
AV1 IN  
VOL  
POWER  
PUSH SEL  
MUTE  
MAP  
SOURCE  
Remote control sensor  
: This book refers to connections to the Panasonic car navigation system that will come onto the market in the future. Descriptions  
regarding the car navigation system are boxed with a dotted line.  
¡The screen brightness is toggled between  
¡Selects or searches for a track, file, sta-  
tion.  
¡Fast forward/fast reverse.  
¡Slow playback ([d]).  
[DIM]  
[
] [  
]
d
q
w
y s  
the set level and maximum luminance.  
(DIMMER)  
(TUNE/TRACK)  
¡Adjusts the sound volume.  
¡Adjusts audio settings.  
[VOL]  
(PUSH SEL)  
¡Ejects/reloads a disc.  
[
]
u u  
¡Mutes the sound temporarily.  
MUTE  
[
]
e
r
Note:  
¡Do not insert a disc when the eject button  
[u] lights because a disc is already  
loaded.  
¡Switches navigation mode on and off.  
(available in the future)  
MAP  
[
]
Note:  
¡From line output of external audio/video  
device. (aInstallation Instructions)  
AV1 IN  
i
o
¡This button is available only when the  
Panasonic Car Navigation System (avail-  
able in the future) is connected to the RGB  
connector of this unit.  
¡Opens/closes the monitor.  
OPEN  
[
]
(CLOSE)  
¡Adjusts the monitor position.  
¡Tilts the monitor forward temporarily.  
¡Switches on/off the power.  
¡Changes the modes such as sound and  
picture.  
TILT  
[
]
[SOURCE]  
(POWER)  
!
t
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
CQ-VX100W  
Anti-Theft System  
This unit is equipped with a removable face plate.  
Removing this face plate makes the unit totally inopera-  
ble.  
DIMMER DIM  
TILT  
OPEN  
CQ-VX100W  
TUNE/TRACK  
AV1 IN  
VOL  
POWER  
PUSH SEL  
MUTE  
MAP  
SOURCE  
10  
Removable face plate  
Remove the Face Plate  
w
e
Switch off the power of the unit.  
q
w Hold the top and bottom of the center part of the face  
plate and pull it down toward you.  
e Pull the face plate toward you.  
r Place the face plate into the case and take it with you  
when you leave the car.  
Install the Face Plate  
Detection switch  
( )  
q
Engage the right and left concave parts (A) on the  
lower rear side of the face plate with the convex parts  
(B) of the main unit.  
q
B
( )  
A
w Raise and press the face plate toward the main unit  
until a click is heard while engaging (A) with (B).  
( )  
B
( )  
A
w
Face Plate Removal Alarm  
This alarm sounds to warn you not to forget to remove  
the face plate before leaving your car.  
This function is activated when Security Alarm is set to  
On . ( page 31)  
a
Caution  
¡Be sure to follow the procedure mentioned above to mount the face plate appropriately. Improper mounting such  
as forcible mounting without engaging the concave parts with the convex parts may cause trouble.  
¡Use caution not to damage the detection switch while mounting the face plate. Failure to observe this may cause  
trouble.  
¡Use caution not to apply excessive force to the removed face plate when the plate is carried or stored. Failure to  
observe this may cause trouble.  
¡This face plate is not waterproof. Do not expose it to water or excessive moisture.  
¡Do not remove the face plate while driving your car.  
¡Do not place the face plate on the dashboard or nearby areas where the temperature rises high.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
CQ-VX100W  
Touch Panel Operation Overview  
❒ Notes on the Touch Panel  
Before operation  
¡Clean the surface of the touch panel. (apage 41)  
Operation  
¡Use only your fingers to operate the touch panel.  
¡Do not press the panel forcefully.  
¡Do not scratch the panel with fingernails or any  
hard objects.  
¡Do not use a pen or other sharp implements to  
operate the touch panel.  
¡Do not bump the front panel.  
aFailure to observe the above may damage or  
break the glass on the surface of the touch  
panel.  
11  
The State of Operation Screen  
Example: DVD mode  
Note  
:
¡The following picture is partly darkened for explanation.  
¡Displaying contents and their positions partly vary with each mode. Refer to the description of each mode for details.  
Prohibition  
Input is not possible  
because the user has  
attempted to perform  
Aspect Button  
(apage 32)  
(only for video source)  
an operation which is  
not supported by the  
disc contents.  
Screen Button  
(apage 32)  
(only for video source)  
Clock time  
(apage 30)  
Disc indicator (apage 17)  
(Lights when a disc is loaded)  
Sound Button (apage 33)  
Source Button  
(Content varies with each source)  
Setup Button  
Displays the Source Selection Screen.  
Displays the Setup Screen.  
Source Selection Screen  
Setup Screen  
Source Selection Screen appears.  
Touch desired source button.  
Setup Screen appears. Select desired setting.  
Setup menu, (apage 28)  
Touch  
to quit.  
Press [SOURCE] to change to desired source.  
Note  
:
¡The screen above appears when no external device is  
connected to this unit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
CQ-VX100W  
Switching the Display  
Please refer to the separate “System Upgrade Guidebook” for how to operate this unit when optional devices are  
connected.  
12  
Note:  
¡
Refer to the instructions of each source.  
¡To switch Operation Screen on, touch the center of touch panel. (Touch  
to cancel)  
¡If no operation takes place for more than 10 seconds when Operation Screen is ON, Operation Screen is turned off.  
Audio Source  
❒
CD  
Touch  
Touch  
.
.
Operation Screen  
List Screen  
❒
MP3  
Touch  
.
Touch  
.
Operation Screen 1  
(folder/file name)  
Operation Screen 2  
(ID3 tag)  
List Screen  
Touch  
.
Video Source  
❒
DVD  
Touch  
Touch  
.
.
Operation Screen 1  
Operation Screen 2  
Operation Screen 2  
❒
DivX  
Touch  
Touch  
.
.
Touch  
.
Operation Screen 1  
List Screen  
Touch  
.
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
CQ-VX100W  
General  
[VOL]  
[TILT]  
[OPEN]  
TILT  
OPEN  
DIMMER  
DIM  
CQ-VX100W  
13  
AV1 IN  
TUNE/TRACK  
VOL  
POWER  
SOURCE  
PUSH SEL  
MUTE  
MAP  
[SOURCE] (POWER)  
[MUTE]  
Preparation: Turn your car’s ignition key to the ACC or ON position.  
General Operations  
Operations  
Power  
–
–
[SOURCE]  
[SOURCE]  
ON :  
Power  
OFF :  
Display Open/Close  
[OPEN]  
–
¡Press once to open. Press again to close.  
Note:  
¡When the display is opened or closed, a loud beep sounds three times.  
¡If the unit stops halfway, press [OPEN] again to draw it all the way out.  
¡Opening/closing the display can be done when the power is off.  
Source selection  
[SOURCE]  
(apage 12)  
RADIO (AM/FM)  
(apage 24)  
(apage 18)  
(apage 26)  
(apage 26)  
Note:  
¡
The sources AV1 and  
AV2 provide the audio  
and video from the  
devices connected to  
AV1 IN and AV2 IN of  
this unit respectively,  
and the source Ext. In  
provides the audio and  
video from the device  
connected to EXT  
DVD (DVD/VCD (Video CD)/CD/MP3/DivX)  
AV1  
AV2  
Sources connected  
to the Expansion  
(aSystem  
Upgrade  
Guidebook)  
Ext. In  
VIDEO IN of this unit via  
the expansion module  
(CY-EM100N, option).  
If there is no external  
sources connected,  
AV1/AV2 mode can be  
set to skip. (apage  
31)  
Module  
(CY-EM100N)  
When the Expansion  
Module (CY-EM100N,  
option) is connected.  
(aSystem Upgrade  
Guidebook)  
HUB1  
¡
HUB2  
HUB3  
HUB4  
……  
Touch/Press and hold for more than 2 seconds  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
CQ-VX100W  
General Operations (continued)  
Operations  
14  
Volume  
q Up  
w Down  
–
Note:  
¡The sound level for  
each source is  
w
q
Setting range: 0 to 40, default: 18  
stored in memory.  
Note:  
¡The volume level can be set independently for each source and each  
disc format.  
Mutes the sound.  
To cancel, press again.  
Mute  
–
–
[MUTE]  
Tilt Angle  
[TILT]  
–
q Press and hold for more than 2 seconds.  
Touch to adjust.  
w
or  
Setting range: 1 to 5  
default: 5  
–
–
the monitor is opened automatically when turning ON ACC.  
Auto  
the monitor is not opened automatically.  
default: Manual  
Manual  
Warning  
¡Do not touch the unit while the display is moving. Inserting hands, fingers or for-  
eign objects into the unit can cause injuries and damage to the unit.  
1
5
Note:  
¡Vertical angle (TILT) is saved in the memory, so when the display is drawn out next, it  
is automatically set at the angle and in the position adjusted before.  
¡After adjusting its angle, also adjust the brightness as well. (apage 32)  
¡The car model and installation conditions may impose some restrictions on the  
adjustment of the monitor's angle.  
Folding Down the  
Display Temporarily  
To raise the display, press again.  
[TILT]  
–
Note:  
¡Even when the unit power is off, you can fold down the display temporarily.  
Caution  
¡Avoid physical shock to the monitor.  
¡Do not place any object on the display, or subject it to undue force.  
¡Do not move the display forcibly.  
¡The monitor movable range may be limited by the type of car, the position where  
the display is mounted, etc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
CQ-VX100W  
Before Disc Playback  
Discs that can be Played Back  
❒ Disc Type  
15  
VCD  
❒ About DivX  
DISC  
DVD  
CD  
CD-R/RW  
(Video CD)  
¡DivX files recorded on CD-Rs/RWs and DVD-Rs/RWs  
are playable. Refer to “Notes on MP3/DivX” for further  
information. (apage 22)  
Recordable  
ReWritable  
Mark/logo  
Disc Size  
❒ Symbols used on jackets  
TEXT  
(Examples of such symbols include)  
(IEC62107)  
2
12 cm  
¡
¡
¡
: Number of subtitle languages  
: Number of audio tracks  
: Number of angles  
Video  
Format  
NTSC / PAL  
LPCM, LPCM  
2
MPEG1, (CD-DA*1),  
3
Audio  
Format  
LPCM (CD-DA*1),  
MP3  
MPEG2,  
Dolby  
MPEG1,  
MPEG2  
(SVCD)  
The numbers indicate the number of languages, tracks,  
angles, etc., recorded on the disc.  
Digital  
2
Region No.  
2, 3, 5, ALL*  
Screen size (H:V aspect ratio)  
*1 CD-DA : A general music CD format.  
Note:  
:
¡
¡
¡
4 3  
: 4:3 standard size  
¡Only discs with logos shown in the “Mark/logo” row of  
the table above are playable.  
¡About CD-Rs and CD-RWs, refer to “Notes on CD-  
Rs/RWs, DVD-Rs/RWs”. (apage 42)  
¡Some copy-protected music CDs are not playable.  
¡Even if you play a dts DVD or a dts CD, analog sound can-  
not be reproduced.  
LB  
: Letterbox (apage 34)  
16:9 wide size  
:
16 9 LB  
: Playback in letterbox format on a standard  
screen (4:3).  
Pan & Scan  
:
16 9 PS  
: Playback in  
(pan and scan)  
(apage 34) format on a standard screen  
(4:3).  
❒ Notes on DVD-Rs/RWs  
¡Do not mix DVD-Video formatted data and other format-  
ted data on the same disc.  
Note:  
The size of the image that is displayed on the screen  
¡
¡Discs in the video recording (VR) format are  
unplayable.  
¡Unfinalized discs are unplayable.  
depends on the screen mode ( Aspect  
page 32), and  
a
on the screen size for the content on the disc.  
¡Use disc-at-once recording for DVD-R DL (double-layer).  
¡Some discs are unplayable depending on the disc itself,  
device, drive and software that are used for disc recording.  
❒ Region Management Information  
This product is designed and manufactured to respond to  
the Region Management Information that is recorded on  
a DVD disc. If the Region number described on the DVD  
disc does not correspond to the Region number of this  
product, this product does not play the disc.  
*2The Region number for this product is “2” (for CQ-  
VX100W2),“3” (for CQ-VX100W3), “5” (for CQ-  
VX100W5) or “ALL”.  
❒ Discs not supported  
The following discs are not played back on this product.  
¡DVD-Audio  
¡DVD+R  
¡VSD  
¡DVD-ROM  
¡DVD+RW  
¡CVD  
¡DVD-RAM  
¡CD-G  
¡CD-ROM (except MP3)  
¡CD-RW (except MP3/DivX and CD-DA)  
Example:  
¡CD-R (except MP3/DivX and CD-DA)  
2 3  
ALL  
¡SACD  
¡Photo CD  
¡CDV  
2
3
5
¡Hybrid SACD (except CD-DA)  
4 5  
¡CD-EXTRA (audio-only playback possible)  
¡DVDs with a region number other than “2”, “3”, “5”  
or “ALL”*2  
¡Playing back a photo CD disc with this unit could  
damage the data that is recorded on the disc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
CQ-VX100W  
Disc Insert/Eject  
■ When a disc is in the player...  
16  
DIMMER  
TILT  
CLOSE  
IN-DASH 7" WIDESCREEN COLOR LCD MONITOR DVD RECEIVER  
/
Printed side  
CQ-VX100W  
TEXT  
[u] (eject)  
lights.  
AV1 IN  
TUNE/TRACK  
VOL  
POWER  
PUSH SEL  
MUTE  
MAP  
Caution  
SOURCE  
¡When the disc is inserted or ejected, to prevent disc  
scratches never exert any downward force on the  
disc.  
Do not insert a disc when the eject button  
because a disc is already loaded.  
lights  
DVD VCD CD MP3 DivX  
DVD VCD CD MP3 DivX  
Disc Insert  
Disc Eject  
¡The mode that supports the disc is selected, and play-  
Press [u] to stop playback and eject the disc.  
back starts.  
(Press [u] again to reload the disc.)  
Note:  
DVD VCD  
¡If you leave a disc in the slot for more than 30 seconds  
after its ejection, the disc will be automatically reloaded  
after loud beep is energized three times.  
¡The audio format is automatically identified.  
(apage 16)  
¡When the menu screen appears, see “Chapter/title  
Selection” on page 20.  
DVD VCD  
¡Due to limitations of certain discs, some DVD and  
VCD (Video CD) discs may not operate as described  
in this manual. Refer to the disc jacket for further  
details.  
When a disc is in the player, change to disc player  
mode (CD, MP3, DivX, DVD or VCD (Video CD)) and  
playback starts.  
¡This unit does not support DVD and VCD (Video  
CD) karaoke functions.  
Note:  
¡Do not insert a disc when the eject button  
lights because a disc is already loaded.  
¡The power will be turned on automatically when a disc  
is loaded.  
¡You can play a disc even if the monitor is closed.  
DVD VCD  
¡The sound may be interrupted for a few moments  
while the audio format is being identified.  
Caution  
¡Do not use irregularly shaped discs.  
¡Do not insert foreign object into the disc slot.  
¡This unit does not support 8-cm disc. In case of  
load such a disc, eject and remove the disc from  
the slot immediately.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
CQ-VX100W  
Disc Player  
Source Button  
DIMMER  
TILT  
CLOSE  
Source Selection  
IN-DASH 7" WIDESCREEN COLOR LCD MONITOR DVD RECEIVER  
/
“
”
Touch Source Button .  
q
d
Touch  
on the Source  
(Disc)  
w
17  
Selection Screen.  
CQ-VX100W  
TEXT  
AV1 IN  
[SOURCE]  
Press  
to change to the  
TUNE/TRACK  
VOL  
POWER  
PUSH SEL  
MUTE  
MAP  
SOURCE  
desired mode.  
[SOURCE]  
Repeat/random indicator  
To switch Operation Screen ON, touch the center of  
touch panel.  
[s] [d]  
Video Mode Display  
DVD  
VCD (Video CD)  
DivX  
Source Button  
Playing time  
Source Button  
Playing time  
Source Button  
Playing time  
Operation Buttons  
Operation Buttons  
Operation Buttons  
(
)
Audio Mode Display  
List Folder/File/Track Selection  
(Example: MP3 mode)  
MP3  
: Folder  
Source Button  
Playing time  
: MP3/DivX file  
qTouch  
Title/text scroll  
Folder selection  
(folder name) to select a folder.  
,
,
: scrolls up/down the file list  
by 1 page.  
: scrolls up/down the file list  
by 1 line.  
Operation Buttons  
wTouch  
(file  
Note:  
¡
name) to play.  
Touch  
to change the display. ( page 13)  
a
Note:  
¡[s] and [d] of the main unit can scroll up and  
down the file list by 1 page, respectively, too.  
¡It is not possible to display the whole tree and file list  
in a folder.  
¡The displayed contents on the touch panel vary with  
circumstances.  
CD  
Current track  
Source Button  
Playing time  
Title/text scroll  
Operation Buttons  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
CQ-VX100W  
Basic Operations  
Operations  
Compatible  
Discs  
Operations  
18  
DVD VCD  
CD  
Track/file Selection  
Next track/file  
[d]  
Beginning of the current track/file  
Previous track/file (Touch/press twice.)  
[s]  
MP3 DivX  
Note:  
DVD  
¡When playing a DVD, there are cases where it is not possible to return to  
the start of a chapter that spans 2 titles.  
DVD VCD  
CD  
Fast forward  
Fast Forward/  
Fast Reverse  
[d]  
Release to resume playback.  
Fast reverse  
Release to resume playback.  
[s]  
MP3 DivX  
The speeds of fast forward and fast reverse change incrementally in 4 steps  
every time the corresponding button is pressed.  
DVD VCD  
DivX  
Folder Selection  
Next folder  
–
MP3 DivX  
Previous folder  
Title/text Scroll  
Stop  
CD MP3 DivX  
–
–
Scrolls the title/text once  
To resume playback, touch  
DVD VCD  
CD  
.
MP3 DivX  
DVD VCD  
Pause  
To resume playback, touch again or touch  
.
CD  
–
MP3 DivX  
¡
Touch/press and hold in the pause mode.  
Slow Playback  
[d]  
Playback is at about 1/3 normal speed.  
To resume normal playback, touch  
Note:  
¡Reverse slow playback is not possible.  
DVD VCD  
DivX  
.
DVD VCD  
CD  
Repeat Play  
*
To cancel, touch again.  
–
MP3 DivX  
*
Repeat Play within the  
Current Folder  
To cancel, touch and hold for more than 2 sec-  
onds again.  
MP3 DivX  
CD  
–
–
–
–
Scan Play  
To cancel, touch again.  
CD  
*
*
Random Play  
To cancel, touch again.  
MP3 DivX  
Random Play within the  
Current Folder  
MP3 DivX  
To cancel, touch and hold again.  
……  
Touch/Press and hold  
* Touch panel symbols will change to indicate these current mode.  
,
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
CQ-VX100W  
Disc Player (continued)  
To switch Operation Screen ON, touch the center of touch panel.  
Chapter/title Selection  
Operations  
Compatible  
Discs  
Operations  
19  
Showing menu and  
selecting an item  
qMenu appears.  
–
–
or  
1
*
d
d
DVD  
VCD  
1 Note on VCD:  
*
wSelect the desired item. (Touch  
when  
1
*
For VCD, touch  
instead of  
the direction buttons shown at left are not dis-  
.
played.)  
d
d
2
eDetermine the setting.  
*
–
–
Toggles the position of the buttons on the screen  
between upper and lower.  
DVD  
–
–
Returns to the previous display.  
qToggles “Chapter number input  
mode”, “Title number input mode”  
and “Number input mode”.  
Starting Playback  
from a specific  
chapter/title  
d
to  
d
Touch the numerical  
key to enter a number  
directly  
DVD  
VCD  
wInput desired number.  
–
–
d
d
ePlayback starts.  
Note:  
For retrying selection during number entry, touch  
¡
.
Note:  
If no operation is performed for 8 seconds after you have touched  
¡
, the operation buttons disappear.  
If the title/chapter number is inputted and no operation is performed for 8 seconds, playback will start from the num-  
¡
ber of the title/chapter entered.  
*2 On-Screen Direct Operation (Only for DVD)  
Some DVDs allow you to operate the DVD menu by  
touching the screen.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
CQ-VX100W  
DVD  
mode display  
Chapter/title selection  
Audio Language/  
Angle/Subtitle Language  
Fast forward/fast reverse  
20  
Touch  
Touch  
.
.
Return  
Repeat play  
Stop/pause/play  
DVD menu  
Useful Function  
Operations  
Compatible  
Discs  
Operations  
Subtitle Language  
–
¡Touch during playback.  
DVD  
DivX  
It is possible to change the subtitle language during play if multiple lan-  
guages are recorded on the disc.  
Note:  
¡There may be a brief delay before the subtitles appear.  
Audio Language  
Angle  
–
¡Touch during playback.  
DVD  
DivX  
It is possible to change the audio language during play if multiple audio lan-  
guages are recorded on the disc.  
¡Touch during playback.  
–
For DVDs which contain scenes which have been shot simultaneously from  
a number of different angles the same scene can be viewed from each of  
DVD  
VCD  
these different angles during play. ( Angle Mark  
page 34)  
a
Stereo & Monaural  
–
It is possible to switch the audio between stereo sound and monaural sound  
(L or R).  
: stereo sound  
ST  
d
: the left channel audio is output on both the left and  
right speakers.  
L-ch  
d
: the right channel audio is output on both the left and  
right speakers.  
R-ch  
Note:  
If no operation is performed for 10 seconds or  
is touched , the operation buttons disappear.  
¡
It may not be possible to switch the language unless the unit is at the DVD menu ( previous page) or is at the DVD  
¡
a
settings. ( page 34)  
a
The language on the DVD settings takes priority when the power is turned on or the disc is loaded.  
The number of languages and angles depend on the disc. Some discs have only one language/angle or have no lan-  
guage/angle.  
¡
¡
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
CQ-VX100W  
Notes on MP3/DivX  
What is MP3/DivX?  
Display Information (on the Main Unit)  
MP3*: MP3 (MPEG Audio Layer-3) is the compression format  
of digital audio. It is developed by MPEG (Motion Picture  
Experts Group). Using this compression format, you can  
record the contents of about 10 music CDs on a single CD  
(This figure refers to data recorded on a 650 MB CD-R or CD-  
RW at a fixed bit rate of 128 kbps and a sampling frequency of  
44.1 kHz).  
Displayed items  
¡CD-TEXT  
Disc title  
¡MP3 (ID3 tag)  
Album name  
Title and artist name  
21  
Track title  
¡MP3/DivX  
Folder name  
File name  
*MPEG Layer-3 audio coding technology licensed form  
Fraunhofer IIS and Thomson.  
Displayable characters  
¡Displayable length of file name/folder name: within 64 char-  
acters. (Unicoded file and folder names are reduced by half  
in the number of displayable characters.)  
DivX: The video compression format developed by DivX, Inc.  
compresses video files without any considerable loss of video  
quality.  
¡Name files and folders in accordance with the standard of each  
file system. Refer to the instructions of writing software for  
details.  
¡ASCII character set can be displayed.  
¡Some Cyrillic characters in the Unicode can be displayed.  
ASCII character set  
Note:  
¡MP3/DivX encoding and CD writing software programs are  
not supplied with this unit.  
Points to remember when making MP3/DivX files  
A to Z, a to z, digits 0 to 9, and the following symbols:  
(space) ! ” # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ _ ` { | } ~  
Common  
Note:  
¡High bit rate and high sampling frequency are recommended  
for high quality sound.  
¡With some software in which MP3/DivX format files have been  
encoded, the character information may not be displayed prop-  
erly.  
¡Selecting VBR (Variable Bit Rate) is not recommended  
because playing time is not displayed properly and sound  
may be skipped.  
¡The playback sound quality differs depending on the encod-  
ing circumstances. For details, refer to the instructions of  
your own encoding software and writing software.  
¡Undisplayable characters and symbols will be converted into  
an asterisk ( ).  
*
¡It is recommended that the length of the file name is less  
than 8 (excluding the file extension).  
MP3  
¡It is recommended to set the bit rate to “128 kbps or more”  
and “fixed”.  
DivX  
¡DivX files greater than 2GB or having no index may not play  
properly on this unit.  
¡This unit supports all resolutions up to maximum of 720 x  
480 (NTSC)/720 x 576 (PAL).  
¡You can select up to 8 types of audios and subtitles on this  
unit.  
¡GMC (Global Motion Compensation) is not supported.  
Caution  
¡ Put only “.mp3” files on an MP3-formatted disc.  
Put only “.DIVX”, “.divx”, “.AVI” and “.avi” files  
on an DivX-formatted disc. Otherwise, abnormal  
sound may be produced during play which can  
damage the speaker and your hearing.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
CQ-VX100W  
Recording  
R
M
ec  
P
o
3
rd/Din  
i
g
v
M
X
P
f
3
il/Wes  
M
o
A
n
fil  
a
es  
C
o
D
n
/
a
D
C
V
D
D
-m-mediadia  
e
¡It is recommended not to use a disc holding two or more  
different format types of files.  
¡You may encounter trouble in playing MP3/DivX files or dis-  
playing the information of MP3/DivX files recorded with cer-  
tain writing software or CD/DVD recorders.  
¡This unit does not have a play list function.  
¡Although Multi-session recording is supported, the use of  
Disc-at-Once is recommended.  
¡If CD-DA files are on the same disc as MP3 or DivX files,  
the songs and the movies may not play in the intended  
order, or some songs or movies may not play at all.  
¡When storing MP3 data and DivX data on the same disc,  
use different folders for each data.  
22  
¡Do not record files other than MP3/DivX files and unneces-  
sary folder on a disc.  
¡The name of an MP3/DivX file should be added by rules as  
shown in the following descriptions and also comply with  
the rules of each file system.  
¡The file extension “.mp3” should be assigned to MP3 files.  
¡The file extension “.DIVX”, “.divx”, “.AVI” or “.avi” should be  
assigned to DivX files.  
Supported file systems  
ISO 9660 Level 1/Level 2, Apple Extension to ISO 9660, Joliet,  
Romeo  
Note:  
¡Apple HFS, UDF 1.50, Mix CD and CD Extra are not support-  
ed.  
(Recommendation: “Points to remember when making MP3/DivX files” on the previous page)  
Audio compression formats  
Compression method  
Bit rate  
VBR  
Yes  
Yes  
Yes  
Sampling frequency  
32, 44.1, 48 kHz  
16, 22.05, 24 kHz  
8 k – 48 kHz  
MPEG 1 audio layer 3 (MP3)  
MPEG 2 audio layer 3 (MP3)  
DivX data created using ver.3.11, 4.x, 5.x  
32 k – 320 kbps  
8 k – 160 kbps  
8 k – 320 kbps  
*
Note:  
* DivX video system/MP2, MP3  
¡VBR is not recommended.  
Folder selection order/file playback order  
Maximum number of files/folders  
¡Maximum number of files: 999  
Root Folder  
1
(Root Directory)  
¡Maximum number of files in one folder: 999  
¡Maximum depth of trees: 8  
¡Maximum number of folders: 255 (Root folder is included.)  
2
q
Folder Selection  
3
w
1
8
In the order  
–
4
e
File Selection  
In the order  
Note:  
–
5
¡You can shorten the duration between data read and  
playback by decreasing the quantity of files or folders, or  
the depth of the hierarchy.  
q
y
6
r
7
¡This unit counts the number of folders irrespective of the  
presence or absence of an MP3/DivX file.  
¡If the selected folder does not contain any MP3/DivX files,  
the nearest MP3/DivX files in the order of playback will be  
played.  
t
y
8
Tree 2  
Tree 1  
Tree 3  
Tree 4  
Tree 8  
(Max.)  
¡Playback order may be different from other MP3/DivX play-  
ers even if the same disc is used.  
¡“ROOT” appears when displaying the root folder name.  
Copyright  
No warranty  
The above description complies with our investigations as of  
December 2007. It has no warranty for reproducibility and  
displayability of MP3/DivX.  
It is prohibited by copyright laws to copy, distribute and  
deliver copyrighted materials such as music without the  
approval of copyright holder except enjoying yourself  
personally.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
CQ-VX100W  
Radio  
Each  
/
All  
Source Button  
Frequency  
Source Selection  
indicator  
“
”
Touch Source Button .  
q
DIMMER  
TILT  
CLOSE  
d
IN-DASH 7" WIDESCREEN COLOR LCD MONITOR DVD RECEIVER  
/
Touch  
w
23  
(Radio) on the  
Source Selection  
Screen.  
Band selection  
Tuning  
*List selection  
Preset stations  
CQ-VX100W  
TEXT  
Auto presetting  
[SOURCE]  
Press  
mode.  
to change to the desired  
AV1 IN  
TUNE/TRACK  
VOL  
POWER  
PUSH SEL  
MUTE  
MAP  
SOURCE  
[SOURCE]  
[s] [d]  
* Appears only when All is selected. ( page 35)  
a
Setup  
Radio  
FM Setup  
Auto Preset  
Each  
/
All  
e
e
e
e
Tuning  
Operations  
Band Selection  
–
Each  
FM 1  
FM 2  
FM 3  
AM  
AM  
All  
FM  
Preparation:  
Select All . ( page 35)  
a
List Selection  
Setup  
Radio  
FM Setup  
Auto Preset  
Each  
/
All  
e
e
e
e
Refer to the next page.  
–
FM 1 (list 1)  
FM 2 (list 2)  
FM 3 (list 3)  
There are 6 stations in each list. You can call up next 6 stations by switching from one  
list to another.  
Up  
[d]  
Station  
Selection  
Down  
[s]  
Up  
Seek Tuning  
[d]  
Down  
[s]  
Touch/press and hold for more than 0.5 second then release. Seeking starts.  
……  
Touch/press and hold  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
CQ-VX100W  
Preset Memory  
Manual Preset Memory  
Select a band and frequency.  
Up to 6 stations can be  
preset in each band.  
to  
24  
–
blinks once  
¡Touch and hold for more than 2 seconds.  
¡The frequency blinks once, and a receiving station is saved in the memory.  
New stations overwrite existing saved stations.  
Auto Preset Memory  
Preparation:  
Select Each . ( page 35) (default: Each  
)
a
Setup  
Radio  
FM Setup  
Auto Preset  
Each  
/
All  
e
e
e
e
Each  
A
Six stations are automati-  
cally preset in each band.  
Select a band.  
6 stations with first to 6th highest in signal  
strength of each band will be preset.  
–
¡Touch and hold for more than 2 seconds.  
¡Once set, the preset stations are sequentially scanned for 5 seconds each. (scanning)  
New stations overwrite existing saved stations.  
All  
B
In total 18 FM stations are  
automatically preset.  
Preparation:  
Select All . ( page 35)  
a
Setup  
Radio  
FM Setup  
Auto Preset  
Each  
/
All  
e
e
e
e
18 stations with first to 18th highest in signal  
strength of all FMs will be preset at once.  
–
¡Touch and hold for more than 2 seconds.  
¡Once set, the preset stations are sequentially scanned for 5 seconds each. (scanning)  
New stations overwrite existing saved stations.  
Preset Station Calling  
Preset Swap  
Select a band or a list.  
to  
–
¡Touch desired preset button.  
Preparation:  
Select All . ( page 35)  
a
e
Setup  
Radio  
FM Setup  
Auto Preset  
Each  
/
All  
e
e
e
A station preset is inter-  
changeable with another  
station preset.  
qSelect the list and the preset number that contains the station to be interchanged  
(see “Preset station calling” above).  
w Select the list and hold down the preset number that contains the targeted channel  
for more than 2 seconds.  
The preset station selected in the step qis  
interchanged with the targeted preset chan-  
nel selected in the step w(Preset Swap).  
–
to  
……  
Touch and hold  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
CQ-VX100W  
AV1/AV2  
Preparation:  
¡Connect an optional external device to the AV1/AV2.  
Source Button  
Source Selection  
25  
DIMMER  
TILT  
CLOSE  
You can view the images and listen to the sounds from  
the connected external devices in the AV1/AV2 mode  
respectively.  
IN-DASH 7" WIDESCREEN COLOR LCD MONITOR DVD RECEIVER  
/
“
”
Touch Source Button .  
q
d
Touch  
/
w
(AV1/AV2) on the  
Source Selection  
Screen.  
CQ-VX100W  
TEXT  
AV1 IN  
TUNE/TRACK  
VOL  
POWER  
PUSH SEL  
MUTE  
MAP  
SOURCE  
[SOURCE]  
AV1 IN  
[SOURCE]  
Press  
to change to the  
desired mode.  
To switch Operation Screen ON, touch the center of  
touch panel.  
Note:  
<Fig. 1>  
You can set up the system so that the AV mode is not  
¡
¡
¡
selected (source skip). (  
Input  
page 31)  
a
Audio (L)  
Audio (R)  
If no operation is performed for 10 seconds or  
touched, the operation buttons disappear.  
Only the pin jack of the supplied Conversion Cable for  
AV 1 IN or a pin jack that has the same electrode  
arrangement can be connected to the AV 1 IN terminal.  
(See Fig. 1.)  
is  
Video  
Ground  
Use of the supplied Conversion Cable for AV 1 IN or an  
audio pin jack that has the same electrode arrangement  
also allows users to enjoy only music. In this case, the  
screen background becomes black.  
¡
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
CQ-VX100W  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
CQ-VX100W  
Settings  
Basic Setting  
Clock  
ID-Code  
Input  
Memory Clear  
Other  
Basic Setting  
Clock setting  
ID Code Setting  
Input Selection  
Memory clearance  
Other settings  
(a  
(a  
(a  
(a  
(a  
page 30)  
page 30)  
page 31)  
page 31)  
page 31)  
27  
Screen  
Dimmer  
Display  
Screen  
Adjusting the brightness  
Display appearance  
Display aspect setting  
(a  
(a  
(a  
page 32)  
page 32)  
page 32)  
Aspect  
Sound  
SQ3  
Bass/Treble  
Balance/Fader  
Sound  
SQ3 setting  
Bass/treble adjustment  
Balance/fader adjustment  
(a  
(a  
(a  
page 33)  
page 33)  
page 33)  
Disc  
Disc  
Audio Language  
Subtitle Language  
Menu Language  
Video Setting  
Audio Setting  
DivX Registration  
DVD Audio Language Setting  
DVD Subtitle Language Setting  
DVD Menu Language Setting  
DVD Video Setting  
DVD Audio Setting  
DivX Registration  
(a  
(a  
(a  
(a  
(a  
(a  
page 34)  
page 34)  
page 34)  
page 34)  
page 35)  
page 35)  
Radio  
Radio  
FM Setup  
Setting for FM stations  
(a  
page 35)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28  
CQ-VX100W  
❏ Setup Operation  
(Example: DVD mode)  
q
w
28  
Touch desired setting.  
Touch  
in Operation Screen.  
e
(Example: setting screen of  
Input  
page 31)  
a
Determines the setting and goes back to the pre-  
vious menu out of the menu.  
Determines the setting and gets out of the menu  
Note:  
¡The display returns to the previous status if there is no operation for more than 60 seconds after changing to the set-  
ting menu.  
¡The item may not be temporarily selected depending on the current disc type or the state of this unit. In such a case,  
change the source to another one and try to set up the item again.  
[DIM] (DIMMER)  
(The screen brightness is toggled between the  
set level and maximum luminance.)  
CQ-VX100W  
TEXT  
TUNE/TRACK  
DIMMER  
TILT  
CLOSE  
AV1 IN  
VOL  
POWER  
SOURCE  
IN-DASH 7" WIDESCREEN COLOR LCD MONITOR DVD RECEIVER  
/
PUSH SEL  
MUTE  
MAP  
[SOURCE]  
(Exit from the menu)  
[VOL]  
(PUSH SEL)  
CQ-VX100W  
TEXT  
AV1 IN  
TUNE/TRACK  
VOL  
POWER  
PUSH SEL  
MUTE  
MAP  
SOURCE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
CQ-VX100W  
Settings (continued)  
Basic Setting  
Screen  
Sound  
Disc  
Radio  
Clock  
ID-Code  
29  
Clock setting  
ID Code Setting  
Prior to operating this unit, it is advisable to assign a 4-  
digit ID code for security. Once the ID code has been set,  
the unit cannot be operated if the main power supply is  
disconnected then re-connected. It is electronically locked  
so that a thief cannot use the stolen unit unless that per-  
son knows the code you have set.  
Display  
(Clock display)  
On  
: clock display ON (“– –:– –” is displayed  
before adjusting the clock.)  
Off  
: clock display OFF  
default: Off  
The ID code operation must be performed only by the  
person to whom the unit belongs.  
Adjust  
(Clock adjustment)  
Generally, it is not necessary to enter the ID code each  
time when using the unit if it has not been disconnected  
from the main power supply (car battery).  
}
{
: Forward  
: Backward  
0
9
to  
4 digits numeric code  
Note:  
default: none  
To start the clock, touch/press  
¡
/
/
[SOURCE]  
Set the Daylight Saving Time manually.  
.
How to set your ID code (for the first time)  
q Enter an 4 digit ID code.  
¡
w Enter the same 4 digit ID code again.  
default: Hour Adjust: 0  
Minute Adjust: 0  
How to change your ID code  
q Enter the preset (old) 4 digit ID code. If the wrong ID  
code is entered, a new ID code cannot be registered.  
w Enter a new 4 digit ID code.  
e Enter the new 4 digit ID code again.  
How to cancel the known ID code  
Enter the preset (old) 4 digit ID code. If the wrong ID  
code is entered, it is not possible to cancel the ID code  
function.  
q
Touch and hold  
until “Completed!” is displayed.  
w
The ID code cancelling procedure is completed. The unit  
now works without an ID code.  
Note:  
¡Should your unit ever require service, cancel your ID  
code before sending for repair.  
¡The ID code setting cannot be eliminated even by the  
memory clear function.  
¡The inputted code is not displayed for your security.  
Caution  
¡Record your registered ID code and keep it in a  
secure location. (Fill in the ID code memo  
(apage 40).) If you forget it, you will be unable  
to use the unit. In case you forget the ID code,  
please consult your nearest Panasonic Service  
Center.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30  
CQ-VX100W  
Input  
Note:  
30  
Input selection  
Really? appears when  
Yes is selected.  
If a non-Panasonic navigation system is connected to  
this unit, we do not guarantee the operations of the  
navigation system.  
¡
: proceed.  
: no memory clear.  
OK  
(AV1 input selection)  
AV1  
Cancel  
: an external device is connected to AV1.  
AV1  
Skip  
: skips AV1.  
default: AV1  
Caution  
¡Be aware that this setting restores the unit to default  
settings, so that all the memories and settings that  
you have set will be eliminated.  
(AV2 input selection)  
AV2  
: an external device is connected to AV2.  
AV2  
: Select one from among NAV1, NAV2, and  
NAV3 with which images are displayed  
most beautifully when a non-Panasonic  
car navigation system is connected.  
NAV1-3  
Other  
Other settings  
(Setting ACC selection ON and  
OFF)  
ACC Select  
: skips AV2.  
default: AV2  
Skip  
On  
Off  
: sets to ON if your car has ACC position.  
: sets to OFF if your car has no ACC posi-  
tion.  
CH-C Video Input  
(aSystem Upgrade Guidebook)  
default:  
On  
(RGB input selection)  
RGB Input  
Note:  
For an ACC-equipped car, select ON. The following  
functions are available.  
The power is turned on automatically when inserting  
a disc or magazine.  
Off selection disables turning on the power of the  
¡
: Select one between RGB1 and RGB2  
with which images are displayed most  
regularly when a car navigation system  
is connected via RGB connector.  
RGB1/2  
¡
¡
default: RGB1  
main unit through the remote control.  
Ext. In  
Caution  
(aSystem Upgrade Guidebook)  
¡Be sure to select off when your car has no ACC  
position in the ignition switch. Failure to do this  
could cause the battery to go dead.  
Memory Clear  
Memory clearance  
The state of all of the current memories are returned to  
default settings.  
(Security Alarm)  
Security Alarm  
On  
: activates the security alarm.  
Note:  
(apage 11)  
¡The ID code is not deleted by executing memory clear.  
Off  
: inactivates the security alarm.  
default:  
: clears the memory to default settings  
Yes  
No  
: no memory clear.  
The display returns to the previous one.  
On  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
CQ-VX100W  
Settings (continued)  
Screen  
Basic Setting  
Sound Disc  
Radio  
(Display)  
Note:  
¡The screen setting screen can be also activated by  
Aspect  
31  
Screen  
touching  
when the button is displayed.  
Display aspect setting  
(apage 12)  
¡The conventional display image  
Normal  
has a 4 to 3 ratio of horizontal to  
vertical.  
¡In this case, a blank area remains  
on the right and left sides of the  
display.  
Dimmer  
Adjusting the brightness  
1
2
3
¡The screen is extended horizontally  
as a whole to the aspect ratio of 16  
to 9.  
¡The extension ratio is the same at  
any point of the screen.  
Full  
Darker  
Brighter  
default:  
1
Note:  
[DIM]  
When  
¡
is pressed, the screen brightness is tog-  
gled between the set level that is adjusted by the proce-  
dure above and the maximum luminance.  
¡The screen is fully extended at the  
normal aspect ratio of 4 to 3.  
¡The top and bottom of the screen  
are slightly cut.  
Zoom  
Just  
Display  
Display appearance  
(Adjust the image contrast)  
Contrast  
¡The screen is extended horizontally  
to the aspect ratio of 16 to 9.  
¡The extension ratio increases  
toward the right and left ends of  
the screen.  
]
: decreases the contrast between black and white.  
: increases the contrast between black and white.  
[
default: Normal  
Note:  
(Adjust the image brightness)  
Bright  
¡The aspect setting screen can be also activated by  
touching  
(apage 12)  
¡This adjustment is common to video mode.  
Aspect  
when the button is displayed.  
]
[
: darkens.  
: lightens.  
¡
You cannot change the aspect in the menu screen and a  
screen in the CD, MP3 and radio mode. These are fixed  
to “Full”.  
(Adjust the image color depth)  
Color  
¡When the rear view camera is in operation with the  
transmission gear shift in the reverse position, the  
image is shown on the “Full” screen only.  
¡In some cases, the picture looks different from the  
original one due to your selection of aspect.  
]
[
: lightens the depth of color on the display.  
: deepens the depth of color on the display.  
(Adjust the image tone or tint)  
Tint  
Caution  
¡This is to remind you that compression or extension  
of the screen using the aspect ratio (screen mode)  
changing function of this product for commercial  
purpose of profit making or viewing/listening by the  
public could infringe on the rights of the author pro-  
tected by the copyright law.  
¡If you expand normal picture (4 to 3) by using  
“Just”, “Zoom” or “Full” aspect to the full of the  
screen, you might not see the periphery of the pic-  
ture, or you might see a distorted picture.  
]
[
: emphasizes green in the color image.  
: emphasizes red in the color image.  
Note:  
¡When the video signal is PAL/SECAM format, adjust-  
ment cannot be performed.  
Setting range: –15 to +15  
default: 0  
Therefore, use the “Normal” mode to see the origi-  
nal picture as the author intended it.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
32  
CQ-VX100W  
Sound  
Basic Setting Screen  
Disc  
Radio  
Note:  
¡
ing  
The sound setting screen can be also activated by touch-  
Balance/Fader  
32  
Sound  
when the button is displayed. (  
a
page 12)  
Balance/fader adjustment  
(Sound level adjustment  
between right and left speakers)  
Balance  
SQ3  
SQ3 setting  
[
]
: right enhanced  
: left enhanced  
Six SQ presets are already provided at shipment in this  
unit.  
Flat  
Pop  
: flat frequency response  
: wide-ranged and deep sound  
: speedy and heavy sound  
: jazz-specific deep sound  
: club and disco-specific sound  
: clear sound  
Setting range: Right 15 to Left 15  
default:  
0
Rock  
Jazz  
Club  
Vocal  
(Sound level adjustment between  
front and rear speakers)  
Fader  
[
]
: front enhanced  
: rear enhanced  
default: Flat  
Setting range: Front 15 to Rear 15  
default:  
You may set your own SQ or modify factory presettings  
in each memories by following the instructions below:  
0
Adjusting level of each preset  
Audio setting with [VOL] (PUSH  
Select the preset SQ that you prefer to adjust.  
q
Touch  
quency band (BASS/MID/TRE).  
Touch or to adjust each frequency.  
or  
to select a frequency in a fre-  
w
SEL) on the main unit  
Bass  
Treble  
Balance  
Audio settings of  
Fader  
,
,
and  
e
can be performed with [VOL] (PUSH SEL)  
on the main unit.  
Adjustable range: –12 dB to +12 dB  
Adjustable frequency:  
q Press [VOL] (PUSH SEL) to select a setting item.  
BASS; 60 Hz, 80 Hz, 100 Hz, 200 Hz  
MID; 500 Hz, 1 kHz, 2 kHz, 3 kHz  
TRE; 10 kHz, 12 kHz, 15 kHz, 18 kHz  
(Regular mode)  
Note:  
d
The new level adjustment will overwrite the previous  
level adjustment.  
¡
Bass  
d
For resuming the factory settings, touch and hold  
¡
Default for more than 2 seconds.  
Treble  
d
Bass/Treble  
Bass/treble adjustment  
(Bass adjustment)  
(Treble adjustment)  
Bass  
Balance  
d
[
: more  
]
: less  
Fader  
Treble  
w Rotate [VOL] to make an adjustment.  
[
: more  
]
: less  
Setting range: –12 dB to +12 dB  
default: 0 dB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
CQ-VX100W  
Settings (continued)  
Disc  
Basic Setting Screen  
Sound  
Radio  
Audio Language  
DVD audio language setting  
Note:  
Video Setting  
Display aspect and DVD software mode  
(Display aspect setting)  
33  
DVD Aspect  
¡These adjustments being executed, playback will start  
from the beginning of a disc.  
: plays a video in 4:3 screen.  
: plays a video in wide screen (16:9).  
default: Wide  
Narrow  
Wide  
: English  
: Chinese  
: French  
English  
Français  
Other  
: other language. Input the language code.  
(apage 43)  
(DVD software mode)  
Letter Box  
default: English  
: plays wide-screen video in Pan & Scan  
mode (in which the left and right edges  
of the screen are cut off).  
Pan & Scan  
Subtitle Language  
: plays wide-screen video in letterbox  
mode (in which black bands appear at  
the top and bottom of the screen).  
Letter Box  
DVD subtitle language setting  
Note:  
¡A disc supporting closed captioning and subtitles may  
overlap each other on the screen. In this case, turn the  
subtitle off.  
default: Pan & Scan  
Note:  
This function is available only when DVD Aspect is set  
¡
¡
¡
¡
: English  
: Chinese  
: French  
English  
to Narrow  
.
Set the software setting according to the symbol used  
Français  
Other  
on jacket. ( page 16)  
a
: other language. Input the language code.  
(apage 43)  
DVD software mode setting is ignored if Pan & Scan  
or Letter Box is already set in the software.  
Screen aspect of the display unit is changed according  
default: English  
to the aspect ratio setting ( page 32) and DVD soft-  
a
ware’s aspect.  
Menu Language  
DVD menu language setting  
(VIDEO OUT terminal setting)  
TV Type  
: English  
: Chinese  
: French  
English  
: sets PAL in accordance with the equip-  
ment connected to VIDEO OUT.  
: sets NTSC in accordance with the  
equipment connected to VIDEO OUT.  
PAL  
Français  
Other  
NTSC  
: other language. Input the language code.  
(apage 43)  
default: PAL  
default: English  
(Angle mark setting)  
Angle Mark  
The angle mark is displayed to indicate the parts where  
multi-angle data is recorded.  
: activates angle mark.  
: inactivates angle mark.  
On  
Off  
default: On  
Download from Www.Somanuals.com. All Manuals Search And Download.  
34  
CQ-VX100W  
Radio  
Basic Setting Screen  
Sound  
Disc  
Audio Setting  
FM Setup  
Audio setting at DVD playing  
(Down mix setting)  
Setting for FM stations  
34  
(Auto preset setting)  
Down Mix  
Auto Preset  
: surround element decodable down mix  
(Lt = Left total, Rt = Right total)  
Lt/Rt  
Each  
All  
: saves the preset stations in each band.  
: saves the preset stations in all FM lists  
regardless of band.  
: simple stereo down mix  
(Lo = Left only, Ro = Right only)  
Lo/Ro  
default:  
Each  
Note:  
This function is available only when “Dolby Digital”  
¡
source is playing.  
default: Lt/Rt  
(Dynamic Range Compression  
setting)  
DR COMP  
: DR COMP ON  
STD  
MIN  
: made with the greatest compression,  
roughly equivalent to a TV broadcast.  
: DR COMP OFF  
Off  
Note:  
This function is available only when “Dolby Digital”  
¡
source is playing.  
default: Off  
DivX Registration  
Show the DivX Registration Code (apage 36)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
CQ-VX100W  
About DivX VOD Content  
DivX Video-on-Demand (VOD) content is encrypted for copyright protection. In order to play DivX VOD content on this  
unit, you first need to register the unit.  
Follow the on line instructions for purchasing DivX VOD content to enter the unit’s registration code and register the  
unit. For more information about DivX VOD, visit www.divx.com/vod.  
35  
Display the unit’s registration  
code  
Regarding DivX content that  
can only be played a set num-  
ber of times  
Touch  
.
q
w
w
Touch Disc  
.
Some DivX VOD content can only be played a set number  
of times. When you play this content, the remaining num-  
ber of plays is displayed. You cannot play this content  
when the number of remaining plays is zero.  
(“Rental Expired” is displayed.)  
Touch DivX Registration  
.
When playing this content  
¡The number of remaining plays is reduced by one if  
- you press [SOURCE].  
- you press [s] / [d] (a / f)  
etc. and arrive at another content or the start of the  
content being played.  
8 alphanumeric characters  
Note:  
¡We recommend that you make a note of this code for  
future reference.  
¡After playing DivX VOD content for the first time,  
another registration code is then displayed in “DivX  
Registration”. Do not use this registration code to pur-  
chase DivX VOD content. If you use this code to pur-  
chase DivX VOD content, and then play the content on  
this unit, you will no longer be able to play any content  
that you purchased using the previous code.  
¡If you purchase DivX VOD content using a registration  
code different from this unit’s code, you will not be  
able to play this content. (“Authorization Error” is dis-  
played.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
36  
CQ-VX100W  
Troubleshooting  
❑ If You Suspect Something Wrong  
Warning  
Check and take steps as described below.  
¡Do not use the unit in an irregular condi-  
tion, for example, without sound, or with  
smoke or a foul smell, which can cause  
ignition or electric shock. Immediately stop  
using the unit and consult your dealer.  
¡Never try to repair the unit by yourself  
because it is dangerous to do so.  
If the described suggestions do not solve the problem, it is rec-  
ommended to take the unit to your nearest authorized Panasonic  
Service Center. The product should be serviced only by qualified  
personnel. Please refer checking and repair to professionals.  
Panasonic shall not be liable for any accidents arising out of neg-  
lect of checking the unit or your own repair after your checking.  
Never take measures especially those other than indicated by  
italic letters in “Possible Solution” described below because  
those are too dangerous for users to handle themselves.  
36  
■ Common  
Possible cause  
Possible solution  
Problem  
a
The power cord (battery, power and ground) is connected in the wrong way.  
aCheck the wiring.  
No power to the unit  
Fuse blows out.  
aEliminate the cause of fuse blowout and replace the fuse with new one.  
Consult your dealer.  
MUTE is set to ON.  
aSet MUTE to OFF.  
Sound is not  
generated.  
The wiring of speaker lines is not correct, or a break or poor contact arises.  
aCheck the wiring in accordance with the wiring diagram. (Installation  
Instructions)  
There is an electromagnetic-wave generator such as a cellular phone near the  
unit or its electrical lines.  
aKeep the electromagnetic-wave generator such as a cellular phone away  
from the unit and the wiring of the unit. In case noise cannot be eliminated  
due to the wiring harness of the car, consult your dealer.  
Noise  
The contact of the ground lead is poor.  
aMake sure that the ground lead is connected to an unpainted part of the  
chassis securely.  
Alternator noise comes from the car.  
aChange the wiring position of the ground lead.  
aMount a noise filter.  
Noise is made in step  
with engine revolutions.  
Some operations are not executable in particular modes such as menu mode.  
aRead the operating instructions carefully and cancel the mode. If the unit is  
still out of order, consult your dealer.  
Some operations are not  
executable.  
There is a break, a short circuit, poor contact or wrong wiring regarding the  
speaker wiring.  
aCheck the speaker wiring.  
No sound from  
speaker(s)  
The speaker channels  
are reversed between  
right and left.  
The speaker wiring is reversed between right and left.  
aPerform the speaker wiring in accordance with the wiring diagram.  
The power of the unit  
fails unintentionally.  
The safety device works.  
aConsult your dealer, or your nearest Panasonic Service Center.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
CQ-VX100W  
Troubleshooting (continued)  
■ Common (continued)  
The conversion cable for AV 1 IN supplied with this unit is not used for the  
Output  
disabled/distorted  
video/audio.  
terminal of AV1 IN.  
aUse the conversion cable for AV 1 IN supplied with this unit for the  
connection.  
37  
■
Display Settings  
The picture is dark. The  
picture is whitish. Something  
is wrong with the picture.  
The picture is light in color.  
The screen is not adjusted properly.  
aMake every adjustment of the screen.  
The display does not go  
back into the unit.  
The monitor stops on the way to the home position.  
aPress [OPEN].  
■ Radio  
Antenna installation or wiring of antenna cable is faulty.  
aCheck whether the antenna mounting position and its wiring are correct. In  
addition, check to see whether the antenna ground is securely connected to  
the chassis.  
Poor reception or noise  
No power is supplied to the antenna amplifier (when using a film antenna, etc.).  
aCheck the wiring of the antenna power lead.  
The number of auto  
preset stations is less  
than 6.  
The number of receivable stations is less than 6.  
aMove to an area where receivable stations number is maximum, and try pre-  
setting.  
The contact of the battery lead is poor, or the battery lead is not always powered.  
aMake sure that the battery lead is connected securely, and preset stations  
again.  
Preset stations cannot  
be stored.  
■
CD  
The disc is inserted upside down.  
aInsert a disc correctly.  
No playback or disc  
ejected  
There is a flaw or foreign object on the disc.  
aRemove the foreign object, or use a flawless disc.  
There is a flaw or foreign object on the disc.  
aRemove the foreign object, or use a flawless disc.  
Sound skipping or noise  
The unit is not sufficiently secured.  
aSecure the unit to the console box.  
Sound skipping due to  
vibration  
The unit is tilted at over 30˚ in the front-to-end direction.  
aMake the angle 30˚ or less.  
Something such as a peeled label obstructs the disc coming out.  
aPress and hold the [u] for more than 10 seconds (disc forced ejection). In  
case that the disc forced ejection does not work, consult your dealer.  
Disc unejectable  
The microcontroller in the unit operates abnormally due to noise or other factors.  
aUnplug the power cord and plug it again. In case the unit is still out of order,  
consult your dealer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
38  
CQ-VX100W  
■ MP3/DivX  
No playback or disc  
ejected  
The disc has unplayable formatted data.  
aRefer to the description about MP3/DivX for playable formats.  
38  
The CD-Rs/RWs/DVD-  
Rs/RWs that are  
playable on other  
devices are not playable  
on this unit.  
The playability of some CD-Rs/RWs/DVD-Rs/RWs may depend on the combina-  
tion of media, recording software and recorder to be used even if these CD-  
Rs/RWs/DVD-Rs/RWs are playable on other devices such as a PC.  
a
Make CD-Rs/RWs/DVD-Rs/RWs in a different combination of media, recording  
software and recorder after referring to the description about MP3/DivX.  
There is a flaw or foreign objects on the disc.  
aRemove the foreign objects, or use a flawless disc. For MP3/DivX, refer to  
the description about MP3/DivX.  
Sound skipping or noise  
Playing VBR (Variable Bit Rate) files may cause sound skipping.  
aPlay Non-VBR files.  
The picture may stop if the DivX files are greater than 2 GB.  
aKeep the file size under 2 GB.  
The picture stops.  
Note:  
¡Refer to “Notes on MP3/DivX”. (apage 22)  
■
DVD  
¡It is not possible to switch if the disc does not have multiple audio  
Cannot switch the audio  
language/subtitle  
languages/subtitle languages/angles recorded on it. (Refer to the guide provid-  
ed with your disc.)  
¡Some discs permit switching through a menu screen.  
¡Sometimes, switching angles is possible only with certain scenes.  
language/angle.  
The audio/subtitle  
language selected in the  
DVD settings is not  
used.  
If audio or subtitles in that language are not recorded on the disc, the audio or  
subtitles do not switch to that language. (Some discs permit switching through a  
menu screen. Refer to the guide provided with your disc.)  
The disc is still unfinalized.  
aFinalize the disc.  
Refer to “Before Disc Playback” (apage 16) or “Notes on Discs”  
(apage 42) for other cases.  
A DVD–R or DVD–RW is  
not playable.  
The disc is in the video recording (VR) format.  
aPlay video formatted discs.  
Refer to “Before Disc Playback” (apage 16) or “Notes on Discs”  
(apage 42) for other cases.  
The audio format is output disabled for this unit such as dts.  
aUse output enabled discs.  
Refer to “Before Disc Playback” (apage 16) or “Notes on Discs”  
(apage 42) for other cases.  
Sound is not generated.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
CQ-VX100W  
Troubleshooting (continued)  
❑ Error Display Messages  
■ CD/MP3/DivX/DVD/VCD (Video CD)  
39  
Display  
Possible cause  
Possible solution  
a
Disc is dirty, or is upside down.  
aCheck disc.  
Non Playable Disc  
Disc has scratches.  
aCheck disc.  
No operation by some cause.  
aPress [u]. If failure persists, press the reset switch. If normal operation is not  
restored, call the store where you purchased the unit or the nearest Panasonic  
Service Center.  
Mechanism error  
The type of the file that is selected is not supported.  
File error  
No Disc  
aCheck disc.  
No disc is in the player.  
aInsert disc into the disc slot.  
The region code of the disc to be used is not compatible with this unit.  
aPress [u] and check the disc.  
Region Code error  
You are trying to play the DivX VOD content that was purchased with a different  
registration code.  
aPurchase the DivX VOD content with the registration code of this unit.  
(apage 36)  
The DivX VOD content has no available play count.  
aPurchase again the content or play another content. (apage 36)  
Note:  
¡There may be cases when the disc numbers affected by an error are displayed before “Non Playable Disc”.  
Model No. CQ-VX100W  
❑ In case you forget the ID  
code...  
ID CODE  
In case you forget the ID code, please consult  
your nearest Panasonic Service Center.  
ID code memo  
Copy the memo at right, fill in the ID code, and  
keep it in a secure location.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
40  
CQ-VX100W  
❑ Product Servicing  
❑ If the Unit Begins to  
If the suggestions in the charts do not solve the problem,  
we recommend that you take it to your nearest authorized  
Panasonic Service Center. The product should be serv-  
iced only by a qualified technician.  
Malfunction...  
Reset switch  
Remove the face plate (apage 11) and insert a hard,  
slender stick into the hole and push the switch.  
40  
Important  
❑ Replacing the Fuse  
Push the switch only when the unit fails to operate with  
any buttons. (Stored settings and adjustments are not  
cleared.)  
If the unit fails to return to normal condition, call the  
nearest Panasonic Service Center and ask for repairs.  
Use fuses of the same specified rating (15 A). Using dif-  
ferent substitutes or fuses with higher rating, or connect-  
ing the product directly without a fuse, could cause fire or  
damage to this unit.  
If the replacement fuse fails, contact your nearest  
Panasonic Service Center for service.  
TILT  
OPEN  
CQ-VX100W  
AV1 IN  
Reset switch  
Note:  
¡If the ID-CODE has been already set, you will be asked  
to enter the ID-CODE right after the unit is restarted.  
Maintenance  
❑ Cleaning this Unit  
Your product is designed and manufactured to ensure a  
minimum of maintenance. Use a dry soft cloth for routine  
exterior cleaning. Never use benzine, thinner or other sol-  
vents.  
To remove stubborn stains  
1 Moisten the soft cloth in dishwashing  
soap diluted with water and wring well.  
2 Wipe lightly. Go over the same surface  
with a dry cloth.  
Alcohol  
Alcohol  
Note:  
¡Since there is the possibility of water drops getting  
inside of the unit, do not directly apply cleanser to the  
surface.  
¡Do not scratch the screen with your nails or other hard  
objects. The resulting scratches or marks will obscure  
the images.  
Pesticide  
Pesticide  
Wax  
Wax  
Thinner  
Thinner  
Benzine  
Benzine  
Caution  
¡If water drops or similar wet substances get inside  
the monitor, it may cause a malfunction.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
41  
CQ-VX100W  
Notes on Discs  
How to hold the disc  
¡Do not touch the underside of the disc.  
Disc insert  
The surfaces of new discs tend to be slippery. Therefore,  
when using such a disc for the first time, it may not load  
satisfactorily even when it has been inserted into the  
unit. At a time like this, insert the disc into the unit as far  
as it will go until it is loaded properly.  
¡Do not scratch the disc.  
¡Do not bend disc.  
¡When not in use, keep disc in the case.  
41  
Printed side  
¡When inserting a disc into or ejecting and removing  
it from the unit, insert it straight in or eject and  
remove it straight out in parallel with the unit.  
Otherwise, the disc may be scratched or marked in  
the process.  
¡When inserting a disc, do not put one disc on anoth-  
er. Failure to observe this may cause the discs to  
be jammed.  
Do not use discs that fit any of the descriptions given  
below. Using these discs may damage the discs or  
cause the unit to malfunction.  
¡Special discs in a shape which is not round  
Do not leave discs in the following places:  
¡Direct sunlight  
¡Near car heaters  
¡Dirty, dusty and damp areas  
¡On seats and dashboards  
¡Partly or wholly transparent disc  
Disc cleaning  
Use a dry, soft cloth to wipe from the center outward.  
Do not attach any seals or labels to your discs.  
Do not write on the disc label in a heavy pen or ballpoint  
pen.  
Wholly transparent disc*  
Partly transparent disc  
*Wholly semi-transparent disc may not be played back.  
¡Discs with adhered labels, etc. on them  
<Correct>  
<Wrong>  
Disc with adhered stickers Labels created by a printer  
or tape  
Notes on CD-Rs/RWs,  
DVD–Rs/RWs  
¡You may have trouble playing back some CD-R/RW,  
DVD–R/RW discs recorded on CD/DVD recorders (CD-  
R/RW, DVD–R/RW drives), either due to their record-  
ing characteristics or dirt, fingerprints, scratches, etc.  
on the disc surface.  
Protective films or sheets  
Disc accessories (stabiliz-  
ers, etc.)  
¡Damaged or deformed discs  
¡CD-R/RW, DVD–R/RW discs are less resistant to high  
temperatures and high humidity than ordinary music  
CDs. Leaving them inside a car for extended periods  
may damage and make playback impossible.  
¡The unit may not successfully playback a CD-R/RW,  
DVD–R/RW that was made by the combination of writ-  
ing software, a CD/DVD recorder (CD-R/RW,  
DVD–R/RW drives) and a disc if they are incompatible  
with one another.  
Shoddily made discs  
Discs with cracks,  
scratches or parts missing  
¡This player does not play CD-R/RW, DVD–R/RW discs  
if the session is not closed.  
¡Be sure to observe the handling instructions of CD-  
R/RW, DVD–R/RW discs.  
Discs with burrs  
Please remove the burrs  
before use.  
¡This player does not play CD-R/RW, DVD-R/RW discs  
which contain other than CD-DA or MP3/DivX data.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
42  
CQ-VX100W  
Language Code List  
In “Other” cases... (apage 34)  
Input the four digit language code pressing the buttons  
to  
.
Touch  
to determine.  
42  
Note:  
Setting is finished and the display returns to the main menu.  
¡
¡
For retrying selection during number entry, touch  
.
DVD language menu (apage 34)  
Code Language Name  
Code Language Name  
Code Language Name  
6565 Afar  
7289 Armenian  
7365 Interlingua  
7378 Indonesian  
7383 Icelandic  
7384 Italian  
7387 Hebrew  
7465 Japanese  
7473 Yiddish  
7487 Javanese  
7565 Georgian  
7575 Kazakh  
7576 Greenlandic  
7577 Cambodian  
7578 Kannada  
7579 Korean  
7583 Kashmiri  
7585 Kurdish  
7589 Kirghiz  
8277 Rhaeto-Romance  
8279 Romanian  
8285 Russian  
8365 Sanskrit  
8368 Sindhi  
8372 Serbo-Croatian  
8373 Singhalese  
8375 Slovak  
8376 Slovenian  
8377 Samoan  
8378 Shona  
8379 Somali  
8381 Albanian  
8382 Serbian  
8385 Sundanese  
8386 Swedish  
8387 Swahili  
8465 Tamil  
6566 Abkhazian  
6570 Afrikaans  
6577 Ameharic  
6582 Arabic  
6583 Assamese  
6589 Aymara  
6590 Azerbaijani  
6665 Bashkir  
6669 Byelorussian  
6671 Bulgarian  
6672 Bihari  
6678 Bengali; Bangla  
6679 Tibetan  
6682 Breton  
6765 Catalan  
6779 Corsican  
6783 Czech  
6789 Welsh  
7665 Latin  
8469 Telugu  
8471 Tajik  
8472 Thai  
8473 Tigrinya  
8475 Turkmen  
8476 Tagalog  
8479 Tonga  
8482 Turkish  
8484 Tatar  
6865 Danish  
6869 German  
6890 Bhutani  
6976 Greek  
6978 English  
6979 Esperanto  
6983 Spanish  
6984 Estonian  
6985 Basque  
7065 Persian  
7073 Finnish  
7074 Fiji  
7678 Lingala  
7679 Laothian  
7684 Lithuanian  
7686 Latvian, Lettish  
7771 Malagasy  
7773 Maori  
7775 Macedonian  
7776 Malayalam  
7778 Mongolian  
7779 Moldavian  
7782 Marathi  
7783 Malay  
8487 Twi  
8575 Ukrainian  
8582 Urdu  
8590 Uzbek  
7079 Faroese  
7082 French  
7089 Frisian  
7165 Irish  
7168 Scots Gaelic  
7176 Galician  
7178 Guarani  
7185 Gujarati  
7265 Hausa  
7784 Maltese  
7789 Burmese  
7865 Nauru  
7869 Nepali  
7876 Dutch  
7879 Norwegian  
7982 Oriya  
8065 Panjabi  
8076 Polish  
8673 Vietnamese  
8679 Volapük  
8779 Wolof  
8872 Xhosa  
8979 Yoruba  
9072 Chinese  
9085 Zulu  
7273 Hindi  
7282 Croatian  
7285 Hungarian  
8083 Pashto, Pushto  
8084 Portuguese  
8185 Quechua  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
CQ-VX100W  
Definition of Terms  
This fully discrete format divides the music signals  
into 5.1 channels: Front Left (L), Front Right (R),  
Centre (C), Left Surround (LS), Right Surround (RS)  
and Subwoofer (SW: 0.1 channel) for recording and  
playback. The number of channels that are recorded  
depends on the software. (1 to 5.1 channels)  
Dolby Digital  
Playback control (VCD (Video CD))  
If the VCD (Video CD) has “With Playback Control”  
or others written on the disc surface or on the jacket,  
the scenes or information to be viewed (or listened  
to) can be selected interactively with the screen by  
looking at the menu shown on the screen.  
In these instructions, playback using the menu  
screen is referred to as the “menu play” for video  
CDs. This player supports Video CDs with playback  
control.  
43  
Manufactured under license from Dolby  
Laboratories.  
“Dolby” and the double-D symbol are trademarks  
of Dolby Laboratories.  
Confidential unpublished works. Copyright  
1992–1997 Dolby Laboratories. All rights  
reserved.  
DivX  
DivX is a popular media technology created by DivX,  
Inc. DivX media files contain highly compressed  
video with high visual quality that maintains a rela-  
tively small file size. DivX files can also include  
advanced media features like menus, subtitles, and  
alternate audio tracks. Many DivX media files are  
available for download online, and you can create  
your own using your personal content and easy-to-  
use tools from DivX.com.  
Interactive DVD  
An interactive DVD is DVD software which includes  
multiple angles, multiple plot endings, etc.  
Letterbox screen  
This refers to a screen on which the playback picture  
of wide-screen DVDs or VCD (Video CD)s appears  
with black bands running along the top and bottom.  
This product incorporates copyright protection  
technology that is protected by U.S. patents and  
other intellectual property rights. Use of this  
copyright protection technology must be authorized  
by Macrovision, and is intended for home and other  
limited viewing uses only unless otherwise  
authorized by Macrovision. Reverse engineering or  
disassembly is prohibited.  
LPCM (Linear PCM audio)  
In this format, the audio signal is converted to digital  
data and recorded in two channels without compres-  
sion. Because the capacity of a DVD disc is large, it  
can store more data with better accuracy than a CD.  
Pan & Scan screen  
This refers to a screen on which the playback picture  
of wide-screen DVDs or VCD (Video CD)s is cut off  
at the left and right sides.  
®
Official DivX Certified product  
®
Plays all versions of DivX video with standard play-  
®
back of DivX media files  
DivX,DivX Certified, and associated logos are trade-  
marks of DivX, Inc. and are used under license.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
44  
CQ-VX100W  
Specifications  
General  
AM radio  
¡Power supply  
: 12 V DC (11 V – 16 V), test  
voltage 14.4 V, negative  
ground  
¡Frequency range  
¡Usable sensitivity  
¡Image rejection ratio  
: 531 kHz – 1 602 kHz  
: 28 dB/µV  
: 50 dB  
44  
¡Current consumption : Less than 10 A (during disc  
playback)  
: 20 W x 4 ch  
(1 kHz, 1 %, 4 Ω)  
Maximum power output : 50 W x 4 ch  
Audio section  
¡Output voltage/  
Impedance  
¡
Power Output  
: 2 Vrms/600 Ω  
¡
¡Frequency  
¡Compatible speaker  
impedance  
¡Video input signal  
characteristics  
¡Dynamic range  
¡S/N ratio  
: 20 Hz – 20 kHz ( 1 dB)  
: 96 dB (during CD playback)  
: 95 dB (during CD playback)  
: 4 Ω  
: Composite video signal, 1.0  
Vp-p (75 Ω)  
¡Audio input sensitivity : 2 Vrms  
¡Video output signal : Composite video signal, 1.0  
Vp-p (75 Ω)  
Pre-Amp output voltage : 2 Vrms  
Pre-Amp output impedance: Less than 600 Ω  
Monitor  
¡Liquid crystal panel  
¡Screen dimensions  
(W x H x D)  
: 7-inch wide  
¡
¡
: 154 x 87 x 177 mm  
: 336 960 pixels (234 vertical  
x 480 horizontal x 3)  
: Over 99.99%  
¡Number of pixels  
¡Dimensions (W x H x D) : 178 x 50 x 165 mm  
¡Weight : 2.4 kg  
¡Valid pixel ratio  
¡Display method  
: Transparent color filter for-  
mat  
: TFT (Thin Film Transistor)  
active matrix format  
Front AV input (AV1 IN)  
¡Input impedance  
: 47 kΩ  
¡Drive method  
¡Allowable external input : 2.0 V  
¡Connector  
: 3.5 mmø Stereo mini pin  
(Equipped with video input  
terminal)  
¡Video input signal  
: Composite video signal, 1.0  
Vp-p (75 Ω)  
¡Audio input sensitivity : 2 Vrms  
FM stereo radio  
¡Frequency range  
¡Usable sensitivity  
¡Stereo separation  
¡S/N ratio  
: 87.5 MHz – 108 MHz  
: 7 dB/µV  
: 30 dB (1 kHz)  
: 62 dB  
Note:  
¡Specifications and the design are subject to modification without notice due to improvements in technology.  
¡Some figures and illustrations on this manual may be different from your product.  
Playable region number  
This operating instruction manual is for 3 models CQ-VX100W2/CQ-VX100W3 and CQ-VX100W5.  
The following table shows the playable region number for each model.  
Model  
Playable region number  
2 (ALL)  
CQ-VX100W2  
CQ-VX100W3  
CQ-VX100W5  
3 (ALL)  
5 (ALL)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
45  
CQ-VX100W  
CQ-VX100W  
Matsushita Electric Industrial Co., Ltd.  
Web Site : http://panasonic.net  
YFM264C059CA PTW1107-1018  
Printed in China  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Cooktop KM 421 User Manual
Milwaukee Power Hammer 2416 20 User Manual
Network Computing Devices Automobile Parts 2172 User Manual
Nextar Digital Photo Frame N8 101 User Manual
Nikon Camcorder Coolpix S3500 User Manual
Olympus Automobile Battery Charger DM 420 User Manual
Omron Network Card CJ2 User Manual
Panasonic Cordless Drill EY6450 U1 User Manual
Panasonic DVD Player DVD RV10 User Manual
Parasound CD Player C DP 1000 User Manual