Operating Instructions
LCD Video Monitor
BT-
P
E
Model No. BT-
Before operating this product, please read the instructions carefully and save this manual for future use.
ENGLISH
D
S0506M0 -H
Printed in Japan
VQT0X79
Download from Www.Somanuals.com. All Manuals Search And Download.
Read this first ! (for BT-LH2600WP) (continued)
FCC NOTICE (USA)
Declaration of Conformity
Model Number:
BT-LH2600WP
Trade Name:
PANASONIC
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ07094
Panasonic Broadcast & Television Systems Company
1-800-524-1448
Support contact:
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instructions and do not make any
unauthorized modifications.
Note:
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference” available from FCC local regional offices
helpful.
Warning:
To assure continued FCC emission limit compliance, the user must use only shielded interface cables when
connecting to host computer or peripheral devices. Also, any unauthorized changes or modifications to this
equipment could void the user’s authority to operate this device.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Read this first ! (for BT-LH2600WE)
Operating precaution
Operation near any appliance which generates strong magnetic fields may give rise to noise in the video and
audio signals. If this should be the case, deal with the situation by, for instance, moving the source of the magnetic
fields away from the unit before operation.
g THIS EQUIPMENT MUST BE EARTHED
WARNING:
To ensure safe operation, the three-pin plug
must be inserted only into a standard three-pin
power point which is effectively earthed through
normal household wiring.
Extension cords used with the equipment must
have three cores and be correctly wired to
provide connection to the earth. Wrongly wired
extension cords are a major cause of fatalities.
The fact that the equipment operates
satisfactorily does not imply that the power point
is earthed or that the installation is completely
safe. For your safety, if you are in any doubt
about the effective earthing of the power point,
please consult a qualified electrician.
• TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
• TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, KEEP THIS EQUIPMENT AWAY
FROM ALL LIQUIDS. USE AND STORE ONLY
IN LOCATIONS WHICH ARE NOT EXPOSED
TO THE RISK OF DRIPPING OR SPLASHING
LIQUIDS, AND DO NOT PLACE ANY LIQUID
CONTAINERS ON TOP OF THE EQUIPMENT.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD AND ANNOYING INTERFERENCE,
USE THE RECOMMENDED ACCESSORIES
ONLY.
g DO NOT REMOVE PANEL COVERS BY
UNSCREWING THEM.
To reduce the risk of electric shock, do not
remove covers. No user serviceable parts
inside.
CAUTION:
In order to maintain adequate ventilation, do
not install or place this unit in a bookcase,
built-in cabinet or any other confined space. To
prevent risk of electric shock or fire hazard due
to overheating, ensure that curtains and any
other materials do not obstruct the ventilation.
Refer servicing to qualified service personnel.
CAUTION:
THE AC RECEPTACLE (MAINS SOCKET
OUTLET) SHALL BE INSTALLED NEAR THE
EQUIPMENT AND SHALL BE EASILY
ACCESSIBLE.
CAUTION:
• Keep the temperature inside the rack to
between 5°C to 35°C.
• Bolt the rack securely to the floor so that it
will not topple over.
TO COMPLETELY DISCONNECT THIS
EQUIPMENT FROM THE AC MAINS,
DISCONNECT THE POWER CORD PLUG
FROM THE AC RECEPTACLE.
indicates safety information.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Read this first ! (for BT-LH2600WE) (continued)
Caution for AC Mains Lead
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC mains cable. One is for continental Europe, etc. and the other one is only
for U.K.
Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable.
FOR CONTINENTAL EUROPE, ETC.
FOR U.K. ONLY
Not to be used in the U.K.
How to replace the fuse
1.Open the fuse compartment with a screwdriver.
FOR U.K. ONLY
This appliance is supplied with a moulded three pin
mains plug for your safety and convenience.
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that
the replacement fuse has a rating of 13 amps and that it
is approved by ASTA or BSI to BS1362.
on the
Check for the ASTA mark
or the BSI mark
body of the fuse.
If the plug contains a removable fuse cover you must
ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used
until a replacement cover is obtained.
2.Replace the fuse.
A replacement fuse cover can be purchased from your
local Panasonic Dealer.
Fuse
indicates safety information.
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic products should not
be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points,where they will be
accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local
retailer upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human
health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local author-
ity for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions for Use
• The liquid crystal portion is manufactured with highly precise technology. It includes over 99.99% effective pixels,
but 0.01% or less of the pixels are either missing, or have fixed lighting (red, blue, green). This is not a sign of
malfunction.
• The liquid crystal protection panel is a specially manufactured component. Wiping it with a hard cloth, or rubbing
it vigorously will scratch the surface.
• If a still image is displayed for a long time, it may cause temporary generation of afterimage (phosphor burn-in).
(However, these afterimages disappear when ordinary moving images are displayed for a while.)
• The response speed and brightness of liquid crystal vary with ambient temperatures.
• Do not install the unit in a place exposed to the direct sunlight. It may otherwise deteriorate the cabinet or
damage the liquid crystal screen.
• The unit is not compatible with the VESA mount.
• When installing, keep the display 10 cm (4 inches) or more away from the back wall and surrounding objects.
Contents
Standard accessories
(For BT-LH2600WP)
Power cord x 1
Power cord hook x 1
Screw x 1
(For BT-LH2600WE)
AC mains lead x 2
AC mains lead hook x 1
Screw x 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Outline
The BT-LH2600W liquid crystal monitor was designed especially for broadcasting service and business use. It is
equipped with a high performance 26-inch wide liquid crystal display panel.
g High performance liquid crystal panel
This monitor achieves outstanding color reproduction, a wide viewing angle, and high-speed response.
g Immediate image output of input signals
*1
Time lag per field caused by IP conversion peculiar to LCD panels is eliminated. The period between input and
picture display is reduced to a minimum.
*1 Conversion from interlace to progressive scanning.
g Multi-format image compatability
• This monitor is equipped with SDI (HD/SD compatible), VIDEO, Y/C, YPBPR/RGB input jacks.
• It supports both NTSC and PAL TV broadcast systems.
g Screen display
You can divide the screen into two windows, and compare the windows using the same input terminal and same
format. Furthermore, you can display a still image or WFM on one of the windows (J page 21 “SUB WINDOW”,
g PIXEL TO PIXEL function
You can use the actual pixel count for picture confirmation when the input is an HD signals (J page 25 “About
g REMOTE control
Depending on the intended use of the monitor, you can select between parallel remote control (GPI) and serial
Dimensions
Unit : mm (inches)
450 (17-3/4)
40.5 (1-5/8)
430 (17)
575.8 (22-3/4) (Display area)
50.5 (2)
663 (26-3/32)
105.5 (4 -1/8)
114 (4-1/2)
270 (10-5/8)
199 (7-7/8)
213 (8-3/8)
4.5 (1/8)
When installing the monitor in one place
permanently, we recommend that you fix
the monitor in place using the screw
holes in the lower part of the stand.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Their Functions (continued)
Front panel
POWER
YPBPR/
RGB
FUNCTION
MENU
ENTER
VIDEO Y/C
SDI 1
SDI 2
4
2
3
5
1
INPUT SELECT
PHASE CHROMA BRIGHT CONTRAST/ VOLUME
BACKLIGHT
POWER switch
This switches the power supply ON/OFF. When the power is ON, the LED (green) lights up.
INPUT SELECT button
This selects the signal input line. The green LED light above the button indicates the selected input signal.
VIDEO
Y/C
SDI1
SDI2
:
:
:
:
Video input
Y/C input
Serial digital interface input (HD/SD compatible)
Serial digital interface input (HD/SD compatible)
YPBPR/RGB : Analog component (YPBPR) or RGB input. Also compatible with PC input RGB.
* When using PC Input, select “RGB-COMP.” from “YPBPR/RGB” in the “INPUT SELECT”
* The monitor retains the input signal settings selected from the last time the monitor was swiched ON or OFF.
MENU button
This is used for menu display, selecting settings, and adjustments.
MENU
:
:
:
Push to display or exit the menu, and to return to the previous menu screen.
Push to move the cursor up or down, or to select an item.
Push to confirm a setting, and to display a submenu.
,
ENTER
FUNCTION button
FUNCTION 1 : Carries out the item selected in the menu.
FUNCTION 2 : Carries out the item selected in the menu.
FUNCTION 3 : Carries out the item selected in the menu.
FUNCTION 4 : Carries out the item selected in the menu.
FUNCTION 5 : Carries out the item selected in the menu.
Picture adjusting knob
PHASE
CHROMA
BRIGHT
0 – 60 (30)
0 – 60 (30)
0 – 60 (30)
CONTRAST 0 – 60 (50)/BACKLIGHT 0 – 60 (60)
( ) denotes factory preset values
A rotating knob that can be pushed to operate. When the picture adjusting knob is pressed, its status is
displayed and adjustment becomes possible. The setting values are saved by pushing the knob again.
When values are changed from the factory preset values, the LED above the knob (amber) lights.
The setting values are loaded when the monitor’s power is switched ON. The setting values are saved when
the knob is pushed, or when 10 seconds pass after changing the settings. However, operating changes
cannot be made in the following cases.
* When the control lock is on, the key mark appears and setting values cannot be changed (J page 29).
* When using “RGB-COMP.” input, [PHASE] and [CHROMA] operations are disabled.
* While operating HV DELAY (J page 24) (when set to any other setting than OFF), [BRIGHT] operation is
disabled.
Volume knob
You can adjust the speaker volume by rotating the volume knob.
Speaker
Audio input from the AUDIO input terminal or SDI terminal (embedded audio) can be heard.
Audio output setting is in the menu.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Their Functions (continued)
Rear panel
1
2
3
4
5
6
7
8
SDI (HD/SD) terminal (BNC)
IN1
IN2
: This is the SDI input terminal (compatible with HD/SD automatic switching).
: This is the SDI input terminal (compatible with HD/SD automatic switching).
SWITCHED OUT : This is the active through-out terminal for the SDI input signal being displayed on the screen.
* SDI active through-out
Signal output results only when [SDI1] or [SDI2] is selected in [INPUT SELECT]. No output results when the
selected input is not SDI.
The terminal is compatible with embedded audio.
Outputting signals received through the SDI input terminals and converted to analog is not possible.
*1*2
VIDEO terminal (BNC)
IN
: This is the VIDEO signal (composite signal) input terminal.
OUT : This is the composite input signal through-out terminal.
*1*2
Y/C terminal
IN
: This is the Y/C signal (S-video signal) input terminal.
OUT : This is the Y/C input signal through-out terminal.
* Wide display (16:9) information from the input signal is not automatically detected.
*1*2
YPBPR/RGB terminal (BNC)
IN
: This is the YPBPR/RGB signal input terminal.
OUT : This is the YPBPR/RGB input signal through-out terminal.
* When using the RGB signal, you can also connect the external synchronizing signal to the SYNC/HD
terminal. When using a PC RGB signal, connect the horizontal synchronizing signal to the SYNC/HD
terminal, and the vertical synchronizing signal to the VD terminal.
VD IN input terminal
This is the vertical synchronizing signal (VD) input terminal used when connecting to a PC RGB signal.
AUDIO input terminal (Pin terminal)
This is the common audio input terminal for all video input terminals.
* When an embedded audio unit BT-YAE1700G (optional) is attached, SDI input audio is automatically
selected by selecting [SDI1] or [SDI2] with [INPUT SELECT].
GPI input terminal (D-SUB 9-pin)
External control is possible by using a GPI signal.
RS-232C input terminal (D-SUB 9-pin)
External control is possible by using a RS-232C signal.
*1 When a cable is not connected to the through-out terminal, the VIDEO IN terminal automatically bears 75 Ω
resistance. When the cable is connected, 75 Ω resistance is removed.
*2 When the through-out terminal is used, depending on connected equipment, the unit's picture level may be
exceeded because 75 Ω resistance at the end of the terminal is automatically removed.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Supply
Connecting and fixing the power cord (for the U.S.A. and Canada)
1. Attach the power cord to the monitor unit.
2. Connect the power cord to the power outlet.
Using the power cord
hook and the screw,
attach the power cord to
the monitor unit.
Power cord
Power cord hook
Screw
Connecting and fixing the AC mains lead (for others)
1. Attach the mains lead to the monitor unit.
2. Connect the AC mains lead to the power outlet.
Using the AC mains lead
hook and the screw,
attach the AC mains lead
to the monitor unit.
AC mains lead
AC mains lead hook
Screw
11
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use the On Screen Menu
Six types of information are displayed on the screen. The input signal status, picture adjusting knob status,
sharpness display, function display, audio level meter display and the menu display.
Input signal status
• VIDEO, Y/C, SDI1, SDI2,
)
SDI1
YPBPR/RGB-VIDEO/RGB-COMP.
2. Various display (FILM mode)
• Displayed when “FILM” is selected in “GAMMA
SELECT”.
3. Signal format
• The display status can be set in “STATUS
DISPLAY” in the “SYSTEM CONFIG” menu
• If “UNSUPPORT SIGNAL” is displayed, then either
the current input signal is not supported or the
“INPUT SELECT” menu setting needs to be
changed.
1
2
3 4
• When “NO SIGNAL” is displayed, there is no input
signal.
4. Various display (lock setting)
• Displayed when control lock is ON.
Note:
“UNSUPPORT SIGNAL” and “NO SIGNAL” may not be
displayed correctly.
Picture adjusting knob status
)
• This knob can be rotated and pushed.
• The status display appears when the knob is
pushed.
The display disappears when the knob is pushed
again, or if the knob is not operated for 10 seconds.
• Settings can only be adjusted in the status display.
Status display:
PHASE, CHROMA, BRIGHT, CONTRAST or BACKLIGHT
Note:
The volume knob status display is not displayed on the
screen.
Sharpness display
• Sharpness is displayed when it is set.
• The display disappears if remains idle for 2 minutes.
SHARPNESS 30
12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use the On Screen Menu (continued)
Function display
• You can set FUNCTION display in the menu.
and either [FUNCTION1] or [FUNCTION5] is
pressed, the unit displays the status of the
FUNCTION item set.
• The display disappears if remains idle for 2 seconds.
• The operational status is displayed in “XXXXX” (J
F1:MARKER
F2:WFM
F3:LEVEL METER
F4:PIXEL TO PIXEL
F5:PIXEL POS.
XXXXX
Audio level meter display
• When the signal is SDI, the audio level is displayed
on the white skeleton bar meter.
• You can switch the level display on and off, and set
the number of displayed channels using the menu.
• The 0 dB line and channel display can be switched
on and off from the menu.
1
3
5
7
2
4
6
8
Channel Level
0 dB
line
display
display
Menu display
• This is displayed when the menu is used.
• The display disappears if remains idle for 2 minutes.
[MAIN MENU]
FUNCTION
HOURMETER
MENU
Displays the operation explanation for the
menu button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use the On Screen Menu (continued)
Menu operations
1. Push [MENU] to display the MAIN menu.
3. Push [
,
] to select the sub menu, then push
[ENTER].
The setting values in the sub menu change to green.
MARKER
MARKER
16:9
4:3
OFF
OFF
OFF
NORMAL
OFF
4:3
BACK
CENTER
GPI PRESET1
GPI PRESET2
4:3
SET
2. Push [
[ENTER].
,
] to select the menu, then push
4. Push [
,
] to select the setting values, then
push [ENTER].
Push [MENU] to cancel.
[MAIN MENU]
FUNCTION
MARKER
MARKER
16:9
ON
OFF
OFF
NORMAL
OFF
4:3
4:3
BACK
MARKER
GPI PRESET1
GPI PRESET2
HOURMETER
MENU
4:3
SET
To return to the previous screen
Push [MENU].
14
Download from Www.Somanuals.com. All Manuals Search And Download.
User Data
You can change the menu setting values and picture adjusting knob settings, then save and load up to 5
combinations of screen adjustment values as user data. You can also return the setting values and adjustment
values to the factory preset settings.
The following settings are included in user data.
• Menu settings except for “SETUP LOAD/SAVE” (including the button function settings on the front of the monitor)
• Screen adjustment values changed in picture adjusting knob
Saving user data
Loading user data
1. Push [MENU] to display the MAIN menu.
1. Push [MENU] to display the MAIN menu.
2. Push [
,
] to select the “SYSTEM CONFIG”
2. Push [
,
] to select the “SYSTEM CONFIG”
menu and push [ENTER].
menu and push [ENTER].
3. Push [
,
] to select the “SETUP SAVE” sub
3. Push [
,
] to select the “SETUP LOAD” sub
menu and push [ENTER].
menu and push [ENTER].
The setting values in the sub menu change to green.
The setting values in the sub menu change to green.
CONT./BACK.
BACKLIGHT
BACKLIGHT
60
CONT./BACK.
BACKLIGHT
BACKLIGHT
60
SUB WINDOW
WFM POSITION
MENU POSITION
ROTARY POSITION
STATUS DISPLAY
SETUP LOAD
FULL
SUB WINDOW
WFM POSITION
MENU POSITION
ROTARY POSITION
STATUS DISPLAY
SETUP LOAD
FULL
RB
CENTER
LB
3SEC OFF
FACTORY
USER1
OFF
RB
CENTER
LB
3SEC OFF
FACTORY
USER1
OFF
SETUP SAVE
FAN MOTOR
SETUP SAVE
FAN MOTOR
COLOR SPACE
EBU
COLOR SPACE
EBU
Changes to green
Changes to green
4. Push [
,
] to select the file you wish to save
4. Push [
,
] to select the file you wish to load to
to from “USER1” – “USER5”, then push [ENTER].
The following screen appears.
from “USER1” – “USER5”, then push [ENTER].
The following screen appears.
To return to the factory preset setting values, select
“FACTORY”.
SETUP SAVE
SETUP LOAD
5. Select “YES”, and push [ENTER].
The user data is saved.
5. Select “YES”, and push [ENTER].
The user data is loaded.
To return to the previous screen
Push [MENU].
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu
Menu configuration
MAIN MENU
MARKER
MARKER
16:9
VIDEO CONFIG
SYSTEM CONFIG
GAMMA SELECT
FILM GAMMA
COLOR TEMP.
SHARPNESS MODE
SHARPNESS H
SHARPNESS V
I-P MODE
4:3
CONT./BACK.
BACK
BACKLIGHT
CENTER
GPI PRESET1
GPI PRESET2
SUB WINDOW
WFM POSITION
MENU POSITION
ROTARY POSITION
STATUS DISPLAY
SETUP LOAD
USER0-63
D93
MONO
D65
ANAMO
D56
SD ASPECT
SCAN
SETUP SAVE
VAR1
VAR2
VAR3
FAN MOTOR
NOISE WIPE
COLOR SPACE
FUNCTION1
FUNCTION
FUNCTION2
FUNCTION3
FUNCTION4
FUNCTION5
FUNCTION DISPLAY
GPI CONTROL
GPI1
GPI
GPI2
INPUT SELECT
VIDEO/ Y/C
GPI3
NTSC SETUP
YPBPR/RGB
GPI4
GPI5
COMPONENT LEVEL
RGB SYNC
GPI6
GPI7
COMP.
AUTOSETUP
H POSITION
V POSITION
PHASE
GPI8
AUDIO
INPUT SELECT
EMBEDDED SELECT L
EMBEDDED SELECT R
LEVEL METER
0 dB POINT
CLOCK
WXGA/XGA
COLOR TEMP.
GAIN RED
GAIN GREEN
GAIN BLUE
BIAS RED
CH
CONTROL
CONTROL
LOCAL ENA.
*[WHITE BALANCE VAR1-3]
OPERATION
LCD
HOURMETER
BIAS GREEN
BIAS BLUE
RESET
FAN
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
MARKER
The underlined values are factory preset setting values.
Sub menu
MARKER
Settings
Explanation
*1
<OFF>
<ON >
Used to make MARKER settings effective.
*2*3
<OFF>
<4:3 >
Used to select/display the type of marker when the aspect ratio
setting is 16:9.
16:9
<13:9>
<14:9>
<CNSCO>
<VISTA>
<95%>
<93%>
<90%>
<88%>
<80%>
<OFF> Marker not displayed.
<4:3>
4:3 marker
<13:9> 13:9 marker
<CNSCO> CNSCO marker
<95%> 95% Area marker
<90%> 90% Area marker
<80%> 80% Area marker
<14:9> 14:9 marker
<VISTA> VISTA marker
<93%> 93% Area marker
<88%> 88% Area marker
*2*4
<OFF>
<95%>
<93%>
<90%>
<88%>
<80%>
Used to select/display the type of marker when the aspect ratio
setting is 4:3.
4:3
<OFF> Marker not displayed.
<95%>
<90%>
<80%>
95% Area marker
90% Area marker
80% Area marker
<93%>
<88%>
93% Area marker
88% Area marker
*2
<
NORMAL
>
Used to select the background brightness excluding the marker.
BACK
<HALF>
<
NORMAL
>
Normal background
<BLACK>
<HALF>
<BLACK>
Background brightness 50%
Background brightness 0% (Black)
*2
<OFF>
<ON>
Used to display the center marker.
CENTER
<OFF>
<ON>
Not displayed
Displayed
*5
*5
<4:3>
<13:9>
<14:9>
<CNSCO>
<VISTA>
<95% (16:9)>
<93% (16:9)>
<90% (16:9)>
<88% (16:9)>
<80% (16:9)>
<95% (4:3)>
<93% (4:3)>
<90% (4:3)>
<88% (4:3)>
<80% (4:3)>
GPI PRESET1: Used to select the marker to be displayed using the
GPI PRESET1
GPI PRESET2
GPI PRESET2: Used to select the marker to be displayed using the
<4:3>
4:3 marker
<13:9> 13:9 marker
<14:9> 14:9 marker
<
CNSCO> CNSCO marker
<VISTA> VISTA marker
<95% (16:9)> 95% Area marker when the aspect ratio is 16:9.
<93% (16:9)> 93% Area marker when the aspect ratio is 16:9.
<90% (16:9)> 90% Area marker when the aspect ratio is 16:9.
<88% (16:9)> 88% Area marker when the aspect ratio is 16:9.
<80% (16:9)> 80% Area marker when the aspect ratio is 16:9.
<95% (4:3)> 95% Area marker when the aspect ratio is 4:3.
<93% (4:3)> 93% Area marker when the aspect ratio is 4:3.
<90% (4:3)> 90% Area marker when the aspect ratio is 4:3.
<88% (4:3)> 88% Area marker when the aspect ratio is 4:3.
<80% (4:3)> 80% Area marker when the aspect ratio is 4:3.
*1 The setting becomes “On” when the unit receives marker-related control during REMOTE operation. (Priority
goes to GPI when GPI settings exist.)
*2 When controlling the marker settings using the GPI function (J page 30), these settings become disabled.
These are not operated when the 2 screens are displayed.
*3 These are only enabled when the HD signal and SD signal aspect ratio settings are 16:9.
*4 These are only enabled when the SD signal aspect ratio setting is 4:3.
*5 When setting “GPI PRESET1” or “GPI PRESET2” using GPI function, the REMOTE function depending RC-
232C becomes disabled (error response: ER001).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
Types of MARKER
g 16:9 marker
g
4:3 marker
(Displayed when using HD, or when using SD
with a 16:9 aspect ratio)
(Displayed when using SD with a 4:3 aspect ratio)
A dotted line is displayed as the marker.
The marker is only displayed as a vertical bar. In
addition, the
BACK” item.
section becomes the “MARKER
95% Area marker
90% Area marker
80% Area marker
93% Area marker
88% Area marker
4:3 marker
13:9 marker
14:9 marker
VISTA marker, CNSCO marker
A horizontal dotted line is displayed as the marker.
(Displayed when using HD, or when using SD with a 16:9 aspect ratio)
A dotted line is displayed as the marker.
VISTA marker
CNSCO marker
When “UNDER” is set in “SCAN” in the “VIDEO
CONFIG” menu, a vertical dotted line is also
displayed as the marker.
95% Area marker
90% Area marker
80% Area marker
93% Area marker
88% Area marker
VISTA marker
Area marker
A dotted line is displayed as the marker.
CNSCO marker
*You can display 4:3 marker at the same time as 16:9 marker.
Simultaneously display example
95% Area marker
90% Area marker
80% Area marker
93% Area marker
The
section becomes the “MARKER BACK” item. The
background selected with the 16:9 marker is controlled.
16:9 marker:
95% Area marker
4:3 marker:
80% Area marker
95% Area marker
88% Area marker
80% Area marker
g Center marker
Center marker
The marker is displayed in
the center of the picture.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
VIDEO CONFIG
The underlined values are factory preset setting values.
Sub menu
GAMMA
SELECT
Settings
Explanation
<STANDARD>
<FILM>
<STDIO/PST>
Used to select the gamma curve.
*1*2
<STANDARD>Standard mode <FILM>FILM mode
<STDIO/PST>Color emphasis mode (in the gamma characteristic in
which shades are valued more than the contrasts, it is suitable for
use by the studio and the post production, etc. )
When FILM is selected,
mark is displayed in the top left of the screen.
*2
<VARICAM>
<OTHER>
Used to select the type of FILM gamma mode.
<VARICAM> VARICAM use
FILM GAMMA
<OTHER>
When using other types than VARICAM
*5
COLOR TEMP.
<USER0–63>
<D93>
Used to select the color temperature.
<USER0–63> Adjustable settings 0–63 (color temperature around 3000K–9300K)
<D93> Color temperature around 9300K
<D65>
<D56>
<D65> Color temperature around 6500K
<VAR1>
<VAR2>
<VAR3>
<D56> Color temperature around 5600K
*4
*4
*4
<VAR1> WB adjustment mode
<VAR3> WB adjustment mode
<VAR2> WB adjustment mode
*3
SHARPNESS
MODE
<HIGH>
<LOW>
Used to select the width of the sharpness edge.
<HIGH> Thin edge <LOW> Thick edge
*2
*3
*2
<0–30>
Used to set the sharpness in the horizontal direction.
When adjusting, the item display moves to the lower part of the screen.
SHARPNESS H
*3
*2
<0–30>
Used to set the sharpness in the vertical direction.
When adjusting, the item display moves to the lower part of the screen.
SHARPNESS V
*2*6
<MODE2>
<MODE1>
Used to set the mode for IP change.
I-P MODE
<MODE2>
Within Field
<MODE1>
Normal mode
*2
<OFF>
<ON>
Used to switch between color and monochrome (MONO).
<OFF> Color <ON> Monochrome
MONO
*
When this is ON, the picture adjusting knob [CHROMA] setting is fixed at 0.
*2*7
<OFF>
<ON>
If an Anamo lens has been used on the camera, and input through
SDI 720/60P, 59.94P, the picture is resized to Anamo size
magnification. (a vertically compressed signal can be amplified
vertically and corrected when it is displayed.)
ANAMO
*2
<4:3>
<16:9>
Used for setting the aspect ratio settings when using SD signal input.
SD ASPECT
<4:3> 4:3 display
<16:9> 16:9 display
*2
<NORMAL>
<UNDER>
Used to set under-scan and normal display.
SCAN
<NORMAL>Normal display
<UNDER>Under-scan
*2
<OFF>
<ON>
<OFF> This makes a fluid and smooth contrast obtainable.
This is especially effective for continuously changing the contrast of
the source signal or CG signal when the S/N is very high.
NOISE WIPE
<ON> Noise reduction mode. Depending on the camera, this mode can
be especially effective for dark scenes. We recommend leaving
this setting “ON” under normal conditions.
*1 During 2 screen display, the changes are not reflected in the still image of the main window.
*2 When “RGB-COMP.” is selected in “YPB R/RGB” in the “INPUT SELECT” menu ( page 27), this does not operate.
*3 The following sharpness values can each be set,
P
J
1) VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
2) any other input line’s HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0)
3) any other input line’s SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
and the setting values for the selected input signal from within this group is displayed. The adjustment status is
displayed in the bottom right when selected.
*4 When “VAR1”, “VAR2” or “VAR3” is selected, the monitor switches to WB adjustment mode (
J
*5 When selecting USER0–63
1) Push [ENTER] (USER changes to blue).
1) change the setting after releasing “SUB WINDOW” function
2) we recommand “MODE2” for the image with a fast movement.
*7 During Anamo size display, SCAN change is not reflected.
2) Select 0–63 with [
,
], and push [ENTER].
J
.
“
”
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
3
g WB adjustment mode
You can adjust “WHITE BALANCE VAR1” – “WHITE BALANCE VAR3” (WB) by selecting “VAR1” – “VAR3” in
“COLOR TEMP.” in the “VIDEO CONFIG” menu.
The underlined values are factory preset setting values.
Sub menu
Settings
Explanation
*1
<USER0–63>
<D93>
Used to select the color temperature that will become the
basis for adjustments.
COLOR TEMP.
<D65>
<USER0
–
63>
Adjustable settings 0–63 (color
<D56>
temperature around 3000K–9300K)
<D93> Color temperature around 9300K
<D65> Color temperature around 6500K
<D56> Color temperature around 5600K
*2
GAIN RED
<0–511>
GAIN elements for RED are adjusted.
(Factory presets are values
for color temperature <D65>.)
* The presets are values
*2
GAIN GREEN
GAIN BLUE
GAIN elements for GREEN are adjusted.
*2
GAIN elements for BLUE are adjusted.
adjusted before shipment
from factories.
*2
BIAS RED
BIAS GREEN
BIAS BLUE
RESET
<-512–511>
(Factory preset settings: 0)
BIAS elements for RED are adjusted.
*2
BIAS elements for GREEN are adjusted.
*2
BIAS elements for BLUE are adjusted.
“GAIN RED” – “BIAS BLUE” values are reset to color
temperatures values selected in “COLOR TEMP.”.
*1 When “COLOR TEMP.” is selected and [ENTER] is pressed following item change, the display changes to the
confirmation screen. Selecting “YES” and pressing [ENTER] on this screen return GAIN and BIAS values to the
selected color temperature values.
*2 When adjusting, the item display moves to the lower part of the screen.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
SYSTEM CONFIG
The underlined values are factory preset setting values.
Sub menu
Settings
Explanation
CONT./BACK.
<CONTRAST>
<BACKLIGHT>
Used to select the function to be assigned to [CONTRAST/
BACKLIGHT] (a knob on the front panel).
<CONTRAST>
Used to adjust CONTRAST.
<BACKLIGHT>
Used to adjust BACKLIGHT.
BACKLIGHT
< 0-60 >
Used to adjust the LCD backlight level.
SUB WINDOW
<FULL>
<PART>
Used to select the type of sub window.
<FULL>
Used to reduce the whole input signal screen, and arrange it
horizontally when it is displayed.
<PART>
Used to cut out the central section of the input signal screen, and
arrange it horizontally when it is displayed (Displayed at the same size
as the previous screen).
WFM POSITION
<LB>
<RB>
<RT>
<LT>
Used to set the WFM display position.
<LB> Bottom left of the screen <RB> Bottom right of the screen
<RT> Top right of the screen
<LT> Top left of the screen
MENU
POSITION
<CENTER>
<LB>
Used to set the on screen menu display position.
<CENTER> Center of the screen
<RB>
<LB> Bottom left of the screen <RB> Bottom right of the screen
<RT>
<RT> Top right of the screen
<LT> Top left of the screen
<LT>
ROTARY
POSITION
<CENTER>
<LB>
Used to set the picture adjusting knob status (on screen menu) display
position.
<RB>
<CENTER> Center of the screen
<RT>
<LB> Bottom left of the screen <RB> Bottom right of the screen
<LT>
<RT> Top right of the screen
<LT> Top left of the screen
STATUS DISPLAY
SETUP LOAD
<CONTINUE>
<3SEC OFF>
<OFF>
Used to set the input signal status (on screen menu) display status.
<CONTINUE>Displayed normally.
<3SEC OFF> After changing status, it is displayed for approximately
3 seconds, and then disappears.
<OFF>
Not displayed.
<FACTORY>
The saved factory preset setting values (FACTORY) or the user data
(USER 1–USER 5) are loaded. Also after loading user data, the screen
displays the signal selected before loading data.
*1
<USER1>
<USER2>
<USER3>
<USER4>
*1
*1
*1
*1
<USER5>
SETUP SAVE
FAN MOTOR
COLOR SPACE
<USER1>
<USER2>
<USER3>
<USER4>
<USER5>
The menu settings and picture adjusting knob adjustment values
(PHASE /CHROMA /BRIGHT /CONTRAST) excluding “SETUP SAVE/
SETUP LOAD” are saved.
<OFF>
<ON>
Used to set fan operation.
<OFF>
The fan is stopped. The brightness of the backlight
automatically lowers.
<ON>
The fan operates. The backlight brightness returns to
normal.
*2
<EBU>
Used to set studio-specified colors.
*2
<SMPTE-C>
*1 When the monitor is shipped from the factory, “USER1” – “USER5” and “FACTORY” all have the same details.
*2 Factory preset settings are The U.S.A. and Canada: SMPTE-C, Others: EBU.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
FUNCTION
The underlined values are factory preset setting values.
Explanation
Sub menu
Settings
FUNCTION 1 –
FUNCTION 5
<HV DELAY>
<AUTOSETUP>
<BLUE ONLY>
<GAMMA SELECT>
<SD ASPECT>
<SCAN>
<SUB WINDOW>
<WFM>
<MARKER>
<PIXEL TO PIXEL>
<PIXEL POS.>
<LEVEL METER>
<MONO>
Used to select the functions to be assigned to individual
buttons [FUNCTION1] to [FUNCTION5] (front-panel buttons).
<HV DELAY>
Displays the synchronizing signal (horizontal, vertical).
The display is switched in the following order.
DELAY OFF J V DELAY J H DELAY J HV DELAY J
DELAY OFF
<AUTOSETUP>
Used to automatically adjust the PC display.
<BLUE ONLY>
Used to cut the red and green signals. You can check the hue
(PHASE) and depth of color (CHROMA). This is switched
between ON/OFF by pushing the button.
<GAMMA SELECT>
<UNDEF>
Used to display the gamma curve.
The display changes in the following order.
GAMMA STANDARD J GAMMA FILM J
GAMMA STDIO/PST J GAMMA STANDARD
<SD ASPECT>
*1
Used to switch between “16:9” and “4:3”.
<SCAN>
(Factory preset
settings
FUNCTION1:
MARKER
FUNCTION2:
WFM
FUNCTION3:
LEVEL METER
FUNCTION4:
PIXEL TO PIXEL
FUNCTION5:
PIXEL POS.)
You can switch between “UNDER SCAN” and “NORMAL
SCAN”.
<SUB WINDOW>
You can perform the settings for 2 screen display mode.
The display changes in the following order.
SINGLE J FULL/PARTJ STILLJ SINGLE
<WFM>
Used to display the wave form monitor.
<MARKER>
Used to switch the marker on and off.
<PIXEL TO PIXEL>
Used to switch the display between the input size and display
size.
*1
*1
<PIXEL POS.>
Used to set the signal display position when PIXEL TO PIXEL
is on.
<LEVEL METER>
Used to switch the AUDIOMETER display.
The display changes in the following order.
METER 8CH J METER 4CH J METER 2CH J OFFJ
METER 8CH
<MONO>
Used to switch the display between color and black-and-
white.
<UNDEF>
No settings
FUNCTION DISPLAY
<ON>
Used to make display settings for the functions assigned to
<OFF>
individual buttons [FUNCTION1] to [FUNCTION5] (front-
panel buttons).
<ON>
The selected function is displayed.
<OFF>
The selected function is not displayed.
*1 If these settings are changed, the menu settings will also change.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
g Restrictions on various FUNCTION settings
Under the following conditions, various settings are disabled.
Setting
Disabling condition
HV DELAY
In SUB WINDOW, WFM or PIXEL TO PIXEL mode, “INVALID FUNCTION” is displayed and the
setting is disabled.
When “YPBPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.”, “INVALID FUNCTION” is
displayed and the setting is disabled.
AUTO
SETUP
When “YPBPR/RGB” set in “INPUT SELECT” menu is other than “RGB-COMP.”, “NOT RGB-
COMP. CH” is displayed and the setting is disabled.
When “YPBPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.” and there is NO SIGNAL,
“INCOMPLETE” is displayed and the setting is disabled.
GAMMA
SELECT
When GPI item is set, “INVALID FUNCTION” is displayed and the setting is disabled.
When “YPBPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.”, “INVALID FUNCTION” is
displayed and the setting is disabled.
SD ASPECT
SCAN
When GPI item is set, “INVALID FUNCTION” is displayed and the setting is disabled.
When SUB WINDOW (still picture) or HD display (including PIXEL TO PIXEL) is on, “INVALID
FUNCTION” is displayed and the setting is disabled.
When GPI item is set, “INVALID FUNCTION” is displayed and the setting is disabled.
In SUB WINDOW or PIXEL TO PIXEL mode, “INVALID FUNCTION” is displayed and the setting
is disabled.
SUB
WINDOW
When “YPBPR/RGB” set in “INPUT SELECT“ menu is other than “RGB-COMP.”, “INVALID
FUNCTION” is displayed and the setting is disabled.
When “RGB-COMP.” is selected in SUB WINDOW with a motion picture on, the screen turns SINGLE.
When an item other than “RGB-COMP.” is selected, two motion pictures are displayed on the
screen. When a still picture is on, blackout occurs.
WFM
In SUB WINDOW or PIXEL TO PIXEL mode, “INVALID FUNCTION” is displayed and the setting
is disabled.
When “YPBPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.” or “RGB-VIDEO”, “INVALID
FUNCTION” is displayed and the setting is disabled.
MARKER
When “YPBPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.”, “INVALID FUNCTION” is
displayed and the setting is disabled.
When GPI item is set or in SUB WINDOW mode, “INVALID FUNCTION” is displayed and the
setting is disabled.
PIXEL TO
PIXEL
When “YPBPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.” or “RGB-VIDEO”, “INVALID
FUNCTION” is displayed and the setting is disabled.
In SUB WINDOW mode, “INVALID FUNCTION” is displayed and the setting is disabled.
PIXEL POS.
When PIXEL TO PIXEL is OFF, “PIXEL TO PIXEL OFF” is displayed and the setting is disabled.
When PIXEL TO PIXEL is 720P display, the position becomes CENTER.
When the display position is not CENTER in PIXEL TO PIXEL mode during 1080P display and
the 720P signal is selected, the display position moves to CENTER.
MONO
When GPI item is set, “INVALID FUNCTION” is displayed and the setting is disabled.
g Operation items displayed when a FUNCTION button is used
When any of the buttons, [FUNCTION1] to [FUNCTION5], is pressed, the following messages are displayed
according to the operation assigned to the pressed button.
• HV DELAY
DELAY OFF, V DELAY, H DELAY, HV DELAY
• MARKER
MAKER OFF, 4:3 MARKER, 13:9 MARKER,
• AUTOSETUP
14:9 MARKER, VISTA MARKER,
CNSCO MARKER, 95% MARKER, 93% MARKER,
90% MARKER, 88% MARKER, 80% MARKER
• PIXEL TO PIXEL/PIXEL POSITION
CENTER, LEFT TOP, LEFT BOTTOM,
RIGHT TOP, RIGHT BOTTOM
COMPLETE: Display for completion
INCOMPLETE: Display for incompletion
NOT RGB-COMP. CH
• GAMMA SELECT
GAMMA STANDARD, GAMMA FILM,
GAMMA STDIO/PST
PIXEL TO PIXEL OFF
• SCAN
• LEVEL METER
NORMAL SCAN, UNDER SCAN
METER OFF, METER 2CH, METER 4CH,
• SUB WINDOW
METER 8CH
SINGLE, FULL/PART, STILL
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
g About HV DELAY
This displays the video blanking period. By pushing the button, you can switch through the H blanking display J
V blanking display J H and V blanking display J no blanking display.
g About the SUB WINDOW
You can compare saved still and moving images by using the “SUB WINDOW” function to separate the main
window into 2 displays as shown below.
Depending on the settings of the “SUB WINDOW” (FULL, PART) in the “SYSTEM CONFIG” menu (J page 21) it
can be switched as shown below.
assigned with the [SUB WINDOW] function. (To use the “SUB WINDOW” function, you must assign it to one of
the [FUNCTION1] to [FUNCTION5] buttons.)
1)change the setting after releasing “SUB WINDOW” function.
2)we recommand “MODE2” for the image with a fast movement.
• FULL
The main window is reduced and made into 2 sub window (sub window+sub window).
Press the FUNCTION button assigned with the SUB WINDOW function.
Normal window
(main window)
Before inputting the image
(sub window+sub window)
After inputting the image
(sub window+sub window)
Press the
same button
again.
Press the
same button
again.
moving image
moving image moving image
still image
moving image
• PART
Only the sub window size is cut out of the main window, and the cut section is made into 2 sub window images
(sub window+sub window).
Press the FUNCTION button assigned with the SUB WINDOW function.
Normal window
(main window)
Before inputting the image
(sub window+sub window)
After inputting the image
(sub window+sub window)
Press the
same button
again.
Press the
same button
again.
moving image moving image
still image
moving image
moving image
The central section is cut out
Lines up and displays the
section cut out of the main
window
The window is displayed in 16:9 aspect.
Precautions when selecting FULL/PART
This function compares screens with the same input terminal and same format. If different input formats, or if
signals are input between different input channels, the sub-window (left side, still image) becomes blurred and
blanking occurs. However, if the same format signals are input into the input terminal when acquiring the still image,
the images will be displayed correctly.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
g About WFM
You can display the wave form monitor using the “WFM” function.
assigned with the [WFM] function (To use the “WFM” function, you must assign it to one of the [FUNCTION1] to
[FUNCTION5] buttons).
Press the FUNCTION button assigned
with the WFM function once.
Normal window
WFM display
Press the
same button
again.
WFM (Wave Form Monitor)
The window is displayed in 16:9 aspect.
Restrictions on WFM
Even if “WFM” has turned ON”, “WFM” is not displayed when using the “PIXEL TO PIXEL” function, “YPBPR/RGB”
set in “INPUT SELECT” menu is “RGB-COMP.” or “RGB-VIDEO”, or using the “SUB WINDOW” function.
g About PIXEL TO PIXEL and PIXEL POS.
Using the “PIXEL TO PIXEL” function, you can confirm a picture with the actual pixel count (only when the input
is an HD signal).
First, press one of the buttons, [FUNCTION1] to [FUNCTION5] (J page 22), assigned with the “PIXEL TO
PIXEL” function to turn it “ON”. With the function on, press another one of the buttons, [FUNCTION1] to
[FUNCTION5] (J page 22), assigned with “PIXEL POS.”. Each time the button assigned with “PIXEL POS.” is
pressed, the signal display position switches. (To use the “PIXEL TO PIXEL” function, “PIXEL TO PIXEL” and
“PIXEL POS.” must be assigned to any two of the buttons, [FUNCTION1] to [FUNCTION5].)
The underlined values are factory preset setting values.
Sub menu
Settings
Explanation
*1*2
<OFF>
<ON>
Used to set the input signal size as the display size.
Compatible formats
PIXEL TO PIXEL
1080/60I/59I/50I/30P/29P/25P/24P/23P/24PSF/23PSF,
720/60P/59P/50P(SDI/YPBPR)
PIXEL POS.
<CENTER>
<LEFT TOP>
<RIGHT TOP>
<RIGHT
BOTTOM>
<LEFT
Used to set the signal display position when PIXEL TO PIXEL
is on.
<CENTER> center
*3
<LT>
<RT>
<RB>
<LB>
top left
top right
bottom right
bottom left
BOTTOM>
*1 When PIXEL TO PIXEL is on, the following menu settings become invalid:
“ON” for “ANAMO” and “UNDER” for “SCAN” set in “VIDEO CONFIG”
Various “HV DELAY” settings in “FUNCTION”
“MARKER display”
*2 When the input signal is “SDI1”, “SDI2” or “YPBPR”, the setting takes effect. However, 1080/60P and 1080/50P
signals are excluded.
*3 When the input signal format is 720, only CENTER is displayed.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
GPI
The “GPI CONTROL” item is used to set enable/disenable of all GPI functions, and assigns functions to each of the
The underlined values are factory preset setting values.
Sub menu
Settings
Explanation
GPI CONTROL
<DISENABLE>
<ENABLE>
GPI functions enable/disenable settings
GPI1–GPI8
<UNDEF>
Used to set the GPI control terminal pin assign.
You can set the same items for each terminal
<MARKER1 ON/OFF>
<MARKER2 ON/OFF>
<MARKER BACKHALF>
<MARKER BACKBLACK >
<CENTER MARKER>
<INPUT SEL. VIDEO>
<INPUT SEL. Y/C>
<INPUT SEL. SDI1>
<INPUT SEL. SDI2>
<INPUT SEL. YPBPR/RGB>
<SD ASPECT>
<SCAN>
<R-TALLY>
<G-TALLY>
<MONO>
<GAMMA SEL. FILM>
<GAMMA SEL. STDIO/
PST>
<RGB SYNC>
Note:
Please be aware that the following can not be performed.
• “SD ASPECT” operation when input signal is HD or PC
• “SCAN” operation when the input signal is PC
• “GAMMA SELECT” operation when the input signal is PC
• “RGB SYNC” operation when anything other than “RGB-VIDEO” is selected in “YPBPR/RGB” in the “INPUT
SELECT” menu
• “MONO” operation when input signal is PC
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
INPUT SELECT
The underlined values are factory preset setting values.
Explanation
Used to select the input format for VIDEO and Y/C input.
Sub menu
VIDEO / Y/C
Settings
*1
<AUTO>
<NTSC>
<PAL>
<AUTO>
<NTSC>
Either NTSC or PAL is automatically selected.
NTSC <PAL> PAL
NTSC SETUP
YPBPR/RGB
<75>
<00>
Selects the NTSC setup level.
<75>
Select this when using with a setup signal of
7.5 IRE. (The inner parts of the monitor are set
to the 7.5 IRE setup level to suit the black level)
Select this when there is no setup level signal.
<00>
<YPBPR>
<RGB-VIDEO>
<RGB-COMP.>
Selects either YPBPR (Component) or RGB input mode.
<YPBPR> Selects the YPBPR signal.
<RGB-VIDEO>Selects the video RGB signal.
<RGB-COMP.>Selects the PC RGB signal.
COMPONENT
LEVEL
<SMPTE>
<B75>
Selects YPBPR (Component) signal input level.
<SMPTE>
When the signal level specified in SMPTE is
<B00>
Chroma 100 IRE PB, PR = 0.7 Vp-p.
<B75>
Select this when connecting a betacam or
simliar devices set to 7.5 IRE. (The inner parts
of the monitor are set at 7.5 IRE setup level to
suit the black level)
<B00>
Select this when connecting a betacam or similar
devices that are not setup to the IRE level.
RGB SYNC
COMP.
<G-ON>
<EXT>
Selects the SYNC when using RGB-VIDEO input.
<G-ON>
Select when a synchronizing signal is
superimposed on the G signal.
<EXT>
Select when an external synchronizing signal is
received in synchronization.
Performs analog PC settings. (Refer to “COMP.” below)
*1 “AUTO” is set when the monitor is shipped from the factory, but if there are concerns about noise etc. from outside the
input signal, we recommend assigning specific format.
g COMP.
The following menus are switched by selecting “RGB-COMP.” in “YPBPR/RGB” in the “INPUT SELECT” menu.
The underlined values are factory preset setting values.
Sub menu
Settings
Explanation
*1
AUTOSETUP
Screen automatic adjustment is performed when “RGB-
COMP.” is selected in “YPBPR/RGB” in the “INPUT SELECT”
menu. “AUTOSETUP” is performed if a different screen is
displayed, and “YES” is selected.
H POSITION
V POSITION
PHASE
<0–60>
(Factory preset setting: 30)
Used to adjust the picture display position in the horizontal
direction.
*2
<0–60>
(Factory preset setting: 30)
Used to adjust the picture display position in the vertical
*2
direction.
*2
<0–31>
Used to adjust the clock phase with 1/32 clock phases.
(Factory preset settings:
*2
CLOCK
<700–1800>
Used to adjust the sampling clock in dot units.
(Factory preset settings:
WXGA/XGA
<XGA>
Switches between WXGA and XGA.
<WXGA>
*1 “EXECUTING” is displayed while “AUTOSETUP” is being executed, and “COMPLETE” is displayed when
“AUTOSETUP” is completed.
If “AUTOSETUP” cannot be completed, “INCOMPLETE” is displayed.
*2 Each “RGB-COMP.” input compatible format can be adjusted.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
g “PHASE” and “CLOCK” factory preset setting values
FORMAT
640x400(70Hz)
640x480(60Hz)
640x480(75Hz)
640x480(85Hz)
800x600(60Hz)
800x600(75Hz)
800x600(85Hz)
CLOCK
800
PHASE
18
FORMAT
1024x768(60Hz)
1024x768(70Hz)
1024x768(75Hz)
1024x768(85Hz)
1280x768(60Hz)
1280x768(75Hz)
1280x1024(60Hz)
CLOCK
1344
1328
1312
1376
1728
1712
1688
PHASE
2
800
17
22
16
17
8
840
10
832
5
1056
1056
1048
31
12
31
20
29
AUDIO
Adjusting the speaker output.
The underlined values are factory preset setting values.
Sub menu
Settings
Explanation
INPUT
SELECT
<AUTO>
<ANALOG>
Used to select speaker output.
<AUTO> When SDI input line is selected with [INPUT SELECT] on the front
panel:
embedded audio (SDI terminal)
When an input line other than SDI1 and SDI2 is selected with
[INPUT SELECT] on the front panel:
analog (AUDIO input terminal)
<ANALOG> Analog (AUDIO input terminal)
EMBEDDED
SELECT L
<CH1–CH8>
(Factory preset
setting: CH1)
Used to select the audio channel of the embedded audio outputted to the left
speaker.
EMBEDDED
SELECT R
<CH1–CH8>
(Factory preset
setting: CH2)
Used to select the audio channel of the embedded audio outputted to the
right speaker.
LEVEL
<OFF>
<8CH>
<4CH>
<2CH>
Used to select the embedded audio meter for on-screen display.
*1
METER
0dB POINT
CH
<ON>
<OFF>
Used to switch the 0 dB line displayed on the meter on and off.
Used to switch the channel displayed on the meter on and off.
<ON>
<OFF>
*1 When speaker output set in “INPUT SELECT” menu is analog, the level meter does not move regardless of its
display status.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (continued)
CONTROL
The underlined values are factory preset setting values.
Sub menu
CONTROL
Settings
Explanation
Used to select the operation. (Combined control lock)
<LOCAL> Front operation enabled
<LOCAL>
<REMOTE>
*1
<REMOTE> Remote operation enabled (The front controls become locked)
LOCAL
<DIS.>
<INPUT>
When “REMOTE” is selected in “CONTROL”, this selects whether front
controls are enabled/disenabled.
*2
ENA.
<DIS.>
All front operations are disabled.
<INPUT>
All controls except for the [INPUT SELECT] button and
volume knob are disabled.
*1 The menu can be displayed when the lock is engaged.
The only menu setting that can be changed when the lock is engaged is the “CONTROL/LOCAL ENA.” item.
When the lock is engaged, the picture adjusting knob is disabled.
Operations when the lock is engaged follow the settings in “LOCAL ENA.”.
When the lock is engaged, the key mark is displayed on the screen.
Key mark
[MAIN MENU]
MARKER
*2 This is only enabled when “CONTROL” is set to “REMOTE”.
HOURMETER
The underlined values are factory preset setting values.
Sub menu
OPERATION
LCD
Settings
<XXH>*3
<XXH>*3
<XXH>*3
Explanation
Used to display the power distribution time.
Used to display the backlight activation time.
Used to display the FAN operation time.*4
FAN
*3 Time is displayed in “XX”.
*4 Linked with the FAN MOTOR ON/OFF status.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE Specifications
REMOTE operation is possible on this monitor using the GPI/RS-232C terminal.
GPI terminal
Each of the items in the GPI screen are compatible with the following terminals.
The functions assigned to each terminal operate when the GND (5 Pin) is connected (ON) or open (OFF).
g Operating conditions
Pin number
Signal
GPI1
GPI2
GPI3
GPI4
GND
GPI5
GPI6
GPI7
GPI8
Level operation: operates when GND is connected.
Edge operation: operates when GND changes from
open to connected.
• If you have assigned a level operation function to
more than one terminal, the function operates as long
as one of the terminals is connected.
1
2
3
4
5
6
7
8
9
GPI Terminal (9P)
Assignment items Function
Operating conditions
UNDEF
No settings (no terminal assignment functions)
—
MARKER1
ON/OFF
Switches the marker display of the marker decided in
Level operation
(Connected: ON, Open: OFF)
*1
“GPI PRESET1” (
J
page 17) in the “MARKER” menu.
MARKER2
ON/OFF
Switches the marker display of the marker decided in
Level operation
(Connected: ON, Open: OFF)
*1
J
MARKER
BACK HALF
MARKER
Reduces the brightness of the background outside the
Level operation
*2
J
(Connected: ON, Open: OFF)
Reduces the brightness of the background outside the
Level operation
(Connected: ON, Open: OFF)
*2
J
BACK BLACK
CENTER MARKER
Switches the center marker display ON/OFF.
(When other markers are being displayed, this is
superimposed on the other markers)
Level operation
(Connected: ON, Open: OFF)
INPUT SEL. VIDEO
INPUT SEL. Y/C
INPUT SEL. SDI1
INPUT SEL. SDI2
Switches the input system to VIDEO.
Switches the input system to Y/C.
Switches the input system to SDI1.
Switches the input system to SDI2.
Switches the input system to YPBPR/RGB.
Edge operation
Edge operation
Edge operation
Edge operation
Edge operation
INPUT SEL.
YPBPR/RGB
SD ASPECT
Sets the aspect ratio settings when using SD signal
input. (Disabled when using HD signal and PC signal)
Level operation
(Connected: 16:9, Open: 4:3)
SCAN
You can switch the scan mode between “UNDER”
and “NORMAL”. (Disabled when using PC signal)
Level operation (Connected: UNDER,
Open: NORMAL)
*3
Lights the red tally.
Level operation
R-TALLY
(
Connected: ON, Open: OFF)
*3
Lights the green tally.
Level operation
Connected: ON, Open: OFF)
G-TALLY
(
MONO
Switches between color and monochrome
(MONO). (Disabled when using PC signal)
Level operation (Connected
:
Monochrome, Open: Color)
GAMMA SEL. FILM
Used to switch the gamma characteristic to the
FILM mode.
Level operation (Connected: FILM
mode, Open: STANDARD mode)
GAMMA SEL.
STDIO/PST
Used to switch the gamma characteristic to the
STDIO/PST mode.
Level operation (Connected: STDIO/
PST mode, Open: STANDARD mode)
*4
Used to select SYNC at the time of RGB-VIDEO
input.
Level operation
(Connected: EXT, Open: G-ON)
RGB SYNC
*1 When the 16:9 marker and 4:3 marker are simultaneously selected and activated on the 16:9 aspect display, both markers are displayed.
*2 When the 16:9 marker and 4:3 marker are simultaneously displayed, the background selected with the 16:9 marker is controlled.
*3 When both “R-TALLY” and “G-TALLY” are ON at the same time, the tally color becomes orange.
*4 This is only enabled when “RGB-VIDEO” is selected in “YPBPR/RGB” in the “INPUT SELECT” menu.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE Specifications (continued)
g Assignment of item priority levels
• When both “MARKER1” and “MARKER2” are ON at the same time, “MARKER1” has priority. However, when the
display aspect is 4:3, the “MARKER1” aspect is 16:9, and the “MARKER2” aspect is 4:3, “MARKER2” is
displayed. In this case, the “MARKER2” background is controlled.
• When “MARKER BACK HALF” and “MARKER BACK BLACK” are simultaneously activated, priority goes to
“MARKER BACK BLACK”.
• When two or more of the following items - “INPUT SEL. VIDEO”, “INPUT SEL. Y/C”, “INPUT SEL SDI1”, “INPUT
SEL. SDI2” and “INPUT SEL. YPBPR/RGB” - are simultaneously activated, priority goes to the last item activated.
• When “GAMMA SEL. FILM” and “GAMMA SEL. STDIO/PST” are simultaneously activated, priority goes to
“GAMMA SEL. FILM”.
RS-232C terminal
Refer to the following diagram and lower right table for the RS-232C terminal pin arrangement and connections.
Please contact the vendor for information about detailed systems which used the RS-232C.
PC Side
Pin number
(Straight)
BT-LH2600W Side
Pin number Signal
N.C.
Signal
N.C.
RXD
TXD
DTR
GND
DSR
RTS
CTS
N.C.
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
TXD
RXD
DSR
GND
DTR
CTS
RTS
N.C.
RS-232C Terminal (9P)
RS-232C REMOTE operation method
g Connectors and signal names
Connector: D-SUB 9-pin (female)
Signal name
g Command format
STX (02h) Command
:
Data
ETX (03h)
• Commands are 3 characters following STX, finally
adding ETX.
• Add a : (colon) after the command as required, and
add the data.
Pin
number
Signal
name
Explanation
1
2
3
4
5
6
7
8
9
N.C. Not connected
TXD Transmission data
RXD Reception data
DSR Connected inside.
GND Ground
g Response formats
1. Setting command response
STX (02h)
Command
ETX (03h)
ETX (03h)
ETX (03h)
2. Query command response
DTR Connected inside.
CTS Connected inside.
RTS Connected inside.
N.C. Not connected
STX (02h)
3. Error response
STX (02h)
Data
Error code
Error code
ER001: Invalid command
ER002: Parameter error
g Communication Conditions
Signal level
Synchro system
Transfer rate
Parity
Conforms to RS-232C
Tone pace synchro system
9600 bps
None
8 bit
Data length
Stop bit
1 bit
Flow control
None
31
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE Specifications (continued)
g Setting command
No Command
Explanation
Input switch
Data
1: SDI2
4: Y/C
Response
IIS
1
0: SDI1
3: YPBPR/RGB
2: VIDEO
IIS
VPC
2
Image quality
adjustment
CON00-60
BRI00-60
CRO00-60
PHA00-60
: Contrast settings
: Brightness settings
: Chroma settings
: Phase settings
VPC
3
4
5
6
7
OBO
OHV
Blue only
HV Delay
0: OFF
1: ON
OBO
OHV
0: OFF
3: HV DELAY
1: H DELAY
2: V DELAY
2: OFF
DSD
ISM
Status display
Analog mode
0: CONTINUE
1: 3SEC OFF
DSD
ISM
ANA0: YPBPR
ANA2: RGB-COMP.
0: G-ON
ANA1: RGB-VIDEO
IRF
RGB Sync
1: EXT
IRF
DMK
Marker settings
16:9 marker
DMK
MK100: OFF
MK102: 88%
MK104: 95%
MK106: 13:9
MK108: 90%
MK110: VISTA
4:3 marker
MK101: 80%
MK103: 93%
MK105: 14:9
MK107: 4:3
MK109: CNSCO
8
MK200: OFF
MK202: 88%
MK204: 95%
Marker background
BAK0: NORMAL
Center marker
CMK0: OFF
MK201: 80%
MK203: 93%
MK208: 90%
BAK1: HALF
CMK1: ON
BAK2: BLACK
9
MGM
MCT
Gamma selection
1: STANDARD
2: FILM
01: D65
04: VAR2
3: STDIO/PST
MGM
MCT
Color temperature
settings
00: D56
03: VAR1
02: D93
05: VAR3
10
10-73: USER0–63
VPC
Sharpness settings
SHP0: LOW
SHP1: HIGH
VPC
11
SHH00-30: Horizontal sharpness settings
SHV00-30: Vertical sharpness settings
12
13
14
15
16
MIP
IP mode settings
Monochrome settings
SD aspect settings
Scan settings
0: MODE1
1: OFF
1: MODE2
2: ON
MIP
OMO
MAS
MSC
MCO
MLE
OMO
MAS
MSC
MCO
MLE
0: 16:9
1: 4:3
0: NORMAL
0: LOCAL
0: DISENABLE
1: UNDER
1: REMOTE
1: INPUT
Remote settings
Remote operation
settings
17
32
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE Specifications (continued)
g Query command
No Command
Explanation
Data
Response
1: SDI2
3: RGB-VIDEO4: VIDEO
6: RGB-COMP.
QIS
1
Input selection
0: SDI1
2: YPBPR
5: Y/C
QPC
2
Image quality
adjustment
CON : Contrast setting value
BRI : Brightness setting value
00-60
00-60
CRO : Chroma setting value 00-60
PHA : Phase setting value
00-60
3
4
QBO
QMK
Blue only
Marker
0: OFF
1: ON
*1
MAK : Area marker
00: OFF
03: 93%
06: 13:9
09: CNSCO
01: 80%
04: 95%
07: 4:3
02: 88%
05: 14:9
08: 90%
10: VISTA
BAK : Background
0: NORMAL 1: HALF
0: OFF
2: BLACK
CMK : Center marker
1: ON
5
6
QGM
QCT
Gamma
1: STANDARD 2: FILM
3: STDIO/PST
Color
temperature
00: D56
01: D65
04: VAR2
02: D93
05: VAR3
03: VAR1
10-73: USER0–63
QPC
Sharpness
SHP : Sharpness mode
0: LOW
1: HIGH
7
SHH : Horizontal sharpness value 00-30
SHV : Vertical sharpness value
00-30
8
9
QIP
IP mode
Monochrome
Aspect
0: MODE1
1: OFF
1: MODE2
2: ON
QMO
QAS
QSC
QAN
10
11
0: 16:9
1: 4:3
Scan
0: NORMAL
1: UNDER
1: RGB-VIDEO
Analog
mode
0: YPBPR
2: RGB-COMP.
12
13
QSY
QFR
RGB sync
Format
0: G-ON
1: EXT
00: NO SIGNAL
01: 1080/60I
03: 1080/50I
05: 1080/29P
07: 1080/24P
09: 1080/24PsF
13: 720/60P
15: 576/50I
02: 1080/59I
04: 1080/30P
06: 1080/25P
08: 1080/23P
10: 1080/23PsF
14: 720/59P
16: 480/60P
18: 576/50P
21: 1080/59P
23: 720/50P
17: 480/60I
20: 1080/60P
22: 1080/50P
14
50: 640
52: 640
54: 800
56: 800
x
x
x
x
400 (70Hz)
480 (75Hz)
600 (60Hz)
600 (85Hz)
51: 640
53: 640
55: 800
x
x
x
480 (60Hz)
480 (85Hz)
600 (75Hz)
57: 1024
58: 1024
59: 1024
60: 1024
61: 1280
62: 1280
63: 1280
x
x
x
x
x
x
x
768 (60Hz)
768 (70Hz)
768 (75Hz)
768 (85Hz)
768 (60Hz)
768 (75Hz)
1024 (60Hz)
FF: UNSUPORT SIGNAL
*1 When the aspect ratio is 16:9, the state of 16:9 markers is returned, and when 4:3, the state of 4:3 markers is
returned.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Error/Warning Displays
If for any reason an error occurs in this monitor, the LEDs above the picture adjusting knob flash at 1-second
intervals (informing you of the error/warning display).
Error/Warning displays
Inverter error
Symptom
Solution
If a malfunction occurs in the inverter that
controls the backlight brightness, the
backlight will switch OFF.
Switch the power supply OFF once, then
switch it back ON again. If an error is still
displayed, contact the vendor where you
purchased the monitor.
The screen becomes completely black.
Fan stop
Error
The fan in the back of the monitor stops if
a malfunction occurs. If a picture is being
displayed when the malfunction occurs, it
will continue being displayed as is.
Switch the power supply OFF once, then
switch it back ON again. If the error is still
displayed after this, contact the vendor
where you purchased the monitor
immediately.
If a fan stop error occurs, setting “FAN
MOTOR” to “OFF” in the “SYSTEM
you to continue using the monitor with
reduced screen brightness.
Maintenance
• To clean the cabinet or surface of the liquid crystal protection panel, gently wipe with a soft, dry cloth.
If the surfaces are extremely dirty, use a soft cloth dipped in a weak detergent solution and then wrung-out to clean the
surfaces, then use a dry cloth to finish. Water or similar substances getting inside the monitor can cause a malfunction.
• Never use thinner or benzene to clean this unit.
Doing so would cause the surface of the monitor to become discolored, and cause paint to peel.
• Do not spray cleansers directly onto the monitor.
Water or similar substances getting inside the monitor can cause a malfunction.
Maintenance Inspections
Maintenance inspections are necessary for the user to use this equipment safely. It is important to keep monitor
functions in good condition at all times through periodical and appropriate maintenance. In order to use this monitor
for a long time, and to make full use of all of its functions, be sure to carry out the following maintenance
inspections.
1. Necessity of periodical maintenance services
A backlight is used in the liquid crystal panel. This
part (consumable) deteriorates as time passes, and
can cause performance levels to drop, or may cause
a malfunction.
2. Standard maintenance time guidelines and items
to be performed
The following maintenance performance times give
standard guidelines for when to perform maintenance,
and do not indicate the individual lifespan of your
equipment. Also, note that the deterioration time
varies depending on the usage environment and way
in which the equipment is used.
Therefore, in addition to the after-service repairs
performed if a malfunction occurs, it is essential that
general servicing and maintenance servicing are
conducted on a regular basis, to prevent malfunctions
and accidents caused by the deterioration of
consumable parts, and to keep the monitor working
normally.
Periodic maintenance
Part name
Backlight
and liquid
crystal panel
Fan
Quantity
inspection time
Replace every 50,000
*
1
1
hours
Replace every 10,000
hours
* You cannot replace just the backlight unit on its own.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
g General
g Input Connectors
Image signal input:
VIDEO:
Input power
Power supply:
Power consumption:
1.5 A – 0.6 A
1 line, BNC x 2
(1 connector with through-out configuration)
Y/C:
AC: 100 V
–
240 V, 50/60 Hz
is the safety infomation.
1 line, Y/C connector x 2
(1 connector with through-out configuration)
Dimensions:
• Including stand
Analog component:
1 line for YPBPR/RGBS, BNC x 8
663 (W) mm x 456.1 (H) mm x 270 (D) mm
[26-3/32 (W) inches x 17-31/32 (H) inches x
10-5/8 (D) inches]
• Main body only, not including stand
663 (W) mm x 441.5 (H) mm x 114 (D) mm
[26-3/32 (W) inches x 17-3/8 (H) inches x
4-1/2 (D) inches]
(4 connectors with through-out configuration)
However, when input is RGB-COMP. this becomes
BNC x 5 (R, G, B, HD, and VD).
(Through-out is not available)
SDI:
2 line, BNC x 3
(1 connector with switched-out configuration)
Audio input:
GPI:
RS-232C:
Pin jack x 2 (stereo)
D-SUB, 9 pins x 1
D-SUB, 9 pins x 1
Weight:
• Including stand
17.5 kg (38.58 lb)
• Main body only, not including stand
15.0 kg (33.07 lb)
Operating temperature:
g Signal level
VIDEO
EXT SYNC signal level:
HD/VD signal level:
AUDIO
AUDIO input level:
Speaker output:
0.3 Vp-p to 4.0 Vp-p
TTL level
+5 °C to +35 °C (+41 °F to +95 °F)
Operating humidity:
20 % to 80 % (no condensation)
Storage temperature:
-20 °C to +60 °C (-4 °F to +140 °F)
0.5 Vrms
0.5 W + 0.5 W
g Panel
Size:
Aspect ratio:
g SDI EMBEDDED AUDIO
26 inches
16:9
HD - SDI:
Compliant with SMPTE299M
Sampling rate:
Number of pixels: 1366 x 768 (WXGA)
Compatible with 48 kHz, synchronous/asynchronous
Compatible with 8 ch
Display colors:
View angle:
Approx. 16.77 millions colors
176° up/down, 176° right/left
SD - SDI:
Sampling rate:
Compliant with SMPTE272M
Compatible with 48 kHz, synchronous
Compatible with 4 ch
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (continued)
g List of compatible signal formats ( : Compatible, : Limited compatibility)
Input signal
formats
VIDEO
Y/C
SDI1
SDI2
YPBPR
RGB-VIDEO
RGB-COMP.
NTSC
PAL
480/59.94I
480/59.94P
576/50I
576/50P
720/50P
720/59.94P
720/60P
*1
*2
*1
*2
*1
*2
*1
*2
1035/59.94I
1035/60I
1080/23.98PsF
1080/24PsF
1080/23.98P
1080/24P
1080/25P
1080/29.97P
1080/30P
1080/50I
1080/50P
1080/59.94I
1080/60I
1080/59.94P
1080/60P
640 x 400 (70Hz)
640 x 480 (60Hz)
640 x 480 (75Hz)
640 x 480 (85Hz)
800 x 600 (60Hz)
800 x 600 (75Hz)
800 x 600 (85Hz)
1024 x 768 (60Hz)
1024 x 768 (70Hz)
1024 x 768 (75Hz)
1024 x 768 (85Hz)
1280 x 768 (60Hz)
1280 x 768 (75Hz)
1280 x 1024 (60Hz)
*1 When 1035/59.94I signal is input, displayed as 1080/59.94I. Other various marker displays will use the 1080/
59.94I marker.
*2 When 1035/60I signal is input, displayed as 1080/60I. Other various marker displays will use the 1080/60I
marker.
Weight and dimensions when shown are approximately.
Specifications are subject to change without notice.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
37
Download from Www.Somanuals.com. All Manuals Search And Download.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY
UNIT COMPANY OF PANASONIC CORPORATION OF NORTH AMERICA
Executive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7196
Southeast Region: (201) 348-7162
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Government Marketing Department:
One Panasonic Way 2E-10, Secaucus, NJ 07094 (201) 348-7587
Broadcast PARTS INFORMATION & ORDERING:
9:00 a.m. – 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880
Emergency after hour parts orders (800) 334-4881
TECHNICAL SUPPORT:
Emergency 24 Hour Service (800) 222-0741
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010
Panasonic de Mexico S.A. de C.V.
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127
Panasonic Puerto Rico Inc.
San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300
Professional & Broadcast IT Systems Business Unit Europe
Panasonic Marketing Europe GmbH
Hagenauer Str. 43, 65203 Wiesbaden-Biebrich Deutschland Tel: 49-611-235-481
Matsushita Electric Industrial Co., Ltd.
© 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.
E P
Download from Www.Somanuals.com. All Manuals Search And Download.
|