This product is eligible for the AVCCAM
3 Year Warranty Repair Program. For
details, see page 5.
Vol.1
Operating Instructions
Memory Card Camera-Recorder
Model No.
AG-HMC80P
1
Volume
Note that Operation Instructions Vol.1 describes basic operations
of the Memory Card Camera-Recorder.
For instructions on advanced operations of the Memory Card
Camera-Recorder, refer to Operating Instructions Vol.2 (pdf file)
contained in the supplied CD-ROM.
Before operating this product, please read the instructions carefully and save this manual for
future use.
D
ENGLISH
VQT2Y43-1
SS0710TU2090 -PS
Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
indicates safety information.
FCC NOTICE (USA)
Declaration of Conformity
Model Number:
Trade Name:
AG-HMC80P
Panasonic
Responsible Party: Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ
07094
Support contact:
1-800-5ꢀ4-1448
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (ꢀ) this device must accept any interference
received, including interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instructions and do not make any
unauthorized modifications.
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference”
available from FCC local regional offices helpful.
FCC Warning:
To assure continued FCC emission limit compliance, follow the attached installation instructions and
the user must use only shielded interface cables when connecting to host computer or peripheral
devices. Also any unauthorized changes or modifications to this equipment could void the user's
authority to operate this device.
NOTIFICATION (Canada)
This class B digital apparatus complies with Canadian ICES-003.
A lithium ion/polymer battery that is recyclable powers the product you have purchased.
Please call 1-800-8-BATTERY for information on how to recycle this battery.
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special
handling may apply.
Note:
Camera-Recorder
The rating plate is on the underside of the camera recorder.
AC Adaptor
The rating plate is on the underside of the AC Adaptor. Disconnect the AC mains plug from the AC mains
socket when not in use.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
ꢀ) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
1ꢀ) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
Conforms to ANSI/UL Std. 60065
4
Download from Www.Somanuals.com. All Manuals Search And Download.
■About batteries that you can use with this unit
(Correct as of August 2010)
The battery that can be used with this unit is VW-VBGꢀ60/VW-VBG6.
• The unit has a function for distinguishing batteries which can be used safety. The dedicated battery
(VW-VBGꢀ60/VW-VBG6) supports this function. The only batteries suitable for use with this unit
are genuine Panasonic products and batteries manufactured by other companies and certified by
Panasonic. (Batteries which do not support this function cannot be used). Panasonic cannot in any
way guarantee the quality, performance or safety of batteries which have been manufactured by other
companies and are not genuine Panasonic products.
It has been found that counterfeit battery packs which look very similar to the genuine product are
made available to purchase in some markets. Some of these battery packs are not adequately
protected with internal protection to meet the requirements of appropriate safety standards. There is
a possibility that these battery packs may lead to fire or explosion. Please be advised that we are not
liable for any accident or failure occurring as a result of use of a counterfeit battery pack. To ensure that
safe products are used we would recommend that a genuine Panasonic battery pack is used.
AVCCAM 3 Year Warranty Repair Program*1
Thank you for purchasing this Panasonic AVCCAM device.
Register as a user for this device to receive a special service warranty up to three years of free warranty repairs.
Customers who register as users on the website will receive an extended warranty repair valid for up to
three years.
1st year
2nd year
3rd year
2
3
4
AVCCAM device
Basic warranty
Extended warranty repair
*
*
*
*1: Please note that this extended warranty is not available in some countries/regions. *2: Not all models eligible for extended warranty coverage.
*3: The basic warranty period may vary depending on the country/region. *4: Not all repair work is covered by this extended warranty.
Free 3 years of Warranty Repairs
Make sure to save the “Registration Notice” e-mail
during the warranty period.
Purchase
AVCCAM product
Register online
within 1 month
“Registration Notice”
e-mail sent
5
Download from Www.Somanuals.com. All Manuals Search And Download.
●SDHC Logo is a trademark of SD-3C, LLC.
●“AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporation.
●This product has been manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
●HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks
of HDMI Licensing LLC in the United States and or other countries.
●Microsoft® and Windows® are trademarks or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
●Screenshots are used in accordance with Microsoft Corporation guidelines.
●Apple®, Macintosh®, and Mac OS® are trademarks or registered trademarks of Apple Inc. in the United
States and/or other countries.
●Other model names, company names, and product names listed in these operating instructions are
trademarks or registered trademarks of their respective companies.
●This product is licensed under the AVC Patent Portfolio License for the personal and non-commercial
use of a consumer, and no license is granted or shall be implied for any use other than the personal
uses detailed below.
– To encode video in compliance with the AVC standard (“AVC Video”)
– To decode AVC Video that was encoded by a consumer engaged in a personal and non-commercial activity
– To decode AVC Video that was obtained from a video provider licensed to provide AVC Video
• Additional information may be obtained from MPEG LA, LLC (http://www.mpegla.com).
– Separate license contracts must be obtained from MPEG LA where SD Memory Cards containing information
recorded with this product are to be distributed to end users for commercial purposes. “End user” refers to
persons or organizations handling such contents for personal use.
Note concerning illustrations in these instructions
• Illustrations (camera-recorder, menu screens, etc.) in these operating instructions differ slightly from the
actual camera-recorder.
References
• References are shown as (Page 00).
Terminology
• Both SD Memory Cards and SDHC Memory Cards as referred to as “SD Memory Cards” in these
operating instructions.
• Video that is created during a single recording operation is referred to as a “clip” in these operating
instructions.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Volume 1 (This Book)
Read this first! ..............................................2
IMPORTANT SAFETY INSTRUCTIONS .......4
Operating precautions.................................8
Precaution for use......................................10
SD Memory Cards compatible with
this product............................................... 1ꢀ
(SD speed class 6)..................... 14
SDHC Memory Cards................................... 14
Compatibility of recorded video.................... 15
About AVCHD............................................... 15
About DV...................................................... 15
Basic Operations................... 30
Turn on/off the camera...............................30
Tally lamp ....................................................30
Using the cursor button.............................31
Basic operations........................................... 31
Menu screen operations............................... 31
Playback mode (PB mode only) .................. 31
Using the viewfinder ..................................32
Using the viewfinder..................................... 3ꢀ
Using as a LCD monitor ............................... 33
Emphasizing outlines ................................... 33
Adjusting the screen display......................... 34
Setting the calendar ...................................35
Setting the time zone.................................... 35
Setting the clock........................................... 35
Basic shooting operations ........................36
Preparing for recording................................. 36
SD Memory Card ACCESS lamp ................. 36
Shooting in auto mode ................................. 37
Checking photos taken (REC CHECK) ........ 38
Using the zoom function............................39
Digital zoom function.................................... 39
Using the setup menus..............................40
Using the menus .......................................... 40
Using the Function Menu ............................. 41
Initializing the menu settings ........................ 41
Setup menu structure ................................42
CAMERA mode menu .................................. 4ꢀ
PHOTO mode menu..................................... 43
DV IN mode menu........................................ 43
PB mode menu............................................. 44
Thumbnail menu (DV mode only)................. 44
Outline.................................... 16
Using this Camera........................................ 16
Shooting and playing back with
this camera............................................... 16
Editing and saving with external devices...... 17
Accessories ................................................18
Optional accessories .................................19
Using tele conversion lenses,
wide conversion lenses ............................ 19
Description of parts....................................20
Front side and rear side ............................... ꢀ0
Right Side..................................................... ꢀ1
Left side........................................................ ꢀꢀ
Remote control............................................. ꢀ3
Preparation............................. 24
Recharging the battery ..............................24
Recharging................................................... ꢀ4
Power sources............................................26
Using the battery .......................................... ꢀ6
Using the AC adaptor ................................... ꢀ6
Adjusting the grip belt ...............................27
Attaching the shoulder strap.....................27
Detaching and attaching the lens hood ...28
Fitting the eye cup......................................28
The remote control.....................................29
Insert the battery .......................................... ꢀ9
Remote control usable range ....................... ꢀ9
Specifications........................ 45
Index ....................................... 48
Volume 2 (CD)
Chapter 1: Operations in AVCHD mode
Chapter 2: Operations in DV mode
Chapter 4: Reference
Before calling for service/Updating the firmware/
Cleaning/Cleaning the eye piece/Storage
Precautions/Software information/Recording
format/How to handle data recorded on SD
Memory Card
Chapter 3: Screen displays and setting
menus
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating precautions
Do not allow any water to get into the camera-
recorder when using it in the rain or snow or at
the beach.
• The AC adaptor may make some noise when you
are using it, but this is normal.
• Failure to heed this caution will cause the
camera-recorder or a card to malfunction (and
may result in irreparable damage).
Take precautions not to drop the camera when
moving it.
• Strong impacts may damage the camera and
cause it to stop working.
Keep the camera-recorder away from
equipment (such as TV sets and video game
machines) that generate magnetic fields.
• Using the camera-recorder on top of or near a
TV set may cause distortion in the images and/or
sound due to the electromagnetic waves that the
set emits.
• Handle the camera with care, using the hand
strap or shoulder strap to carry it.
Do not spray the camera with insect sprays or
other volatile substances.
• These can warp the camera or cause the finish
to come off.
• The powerful magnetic fields generated by
speakers or large motors may damage your
recordings or distort the images.
• Do not leave the camera-recorder in contact with
rubber or PVC products for extended periods of
time.
• The electromagnetic waves emitted from a
microcomputer will adversely affect the camera-
recorder, causing the images and/or sound to be
distorted.
After use, remove the battery and disconnect
the AC power supply cable.
• If the camera-recorder is so adversely affected by
products that generate magnetic fields that it no
longer operates properly, turn it off and remove
the battery or unplug the AC adaptor from the
power outlet. Then install the battery again or
reconnect the AC adaptor. After this, turn the
camera-recorder back on.
Battery characteristics
This camera-recorder uses a rechargeable lithium-
ion battery that uses its internal chemical reaction
to generate electrical energy. This reaction is
easily influenced by the ambient temperature and
humidity, and the battery’s effective operating time
is reduced as the temperature rises or falls. In
very low temperatures, the battery may last only 5
minutes.
Do not use the camera-recorder near radio
transmitters or high-voltage equipment.
• Using the camera-recorder near a radio
transmitter or high-voltage equipment may
adversely affect the recorded images and/or
sound.
Protective circuitry functions if you use the battery
where it is very hot and you will have to wait before
you can use it again.
Remove the battery after use.
Completely remove the battery. (The battery
continues to be used even if you have turned
the camera off.) The battery can over discharge
if you leave it in the camera and it may become
impossible to recharge it.
Do not allow any sand or dust to get into the
camera-recorder when using it at the beach
and other similar places.
• Sand and dust can damage the camera-recorder
or a card. (Be especially careful when inserting or
removing a card.)
Disposing of spent batteries
The battery will become unchargeable. Rather than
throwing the battery into the garbage, take it to a
store that can assist in recycling it.
AC adaptor and battery
• If the CHARGE lamp continues to blink even
when the battery temperature is normal, there
may be something wrong with the battery or AC
adaptor. Contact your dealer.
• The battery takes longer to charge when it is
warm.
• The AC adaptor can interfere with radio reception
so keep radios at least 1 meter away from it.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
What to remember when throwing memory
cards away or transferring them to others
Formatting memory cards or deleting data using
the functions of the unit or a computer will merely
change the file management information: it will
not completely erase the data on the cards. When
throwing these cards away or transferring them
to others, either physically destroy them or use a
data deletion program for computers (commercially
available) to completely erase the data. Users are
responsible for managing the data on their memory
cards.
Liquid crystal displays
• Images or letters can get burned onto the
viewfinder’s LCD monitor if they are displayed
for a long time, but you can fix this by leaving the
camera off for several hours.
• The pixels of the LCD monitor are controlled to
obtain high precision with 99.99 % of the effective
pixels. This leaves less than 0.01 % of pixels
that may not light or may remain on all the time.
These phenomena are normal and will have no
effect on the images you shoot.
• Condensation may form if you use the camera
where temperatures fluctuate. Wipe dry with a
soft, dry cloth.
• The viewfinder’s LCD monitor may appear dim
after immediately turning on a cold camera, but
will brighten as the camera warms up.
Do not point the lens or viewfinder at the sun.
Doing so may damage the parts inside.
Protective caps for the connectors
Keep the protective caps fitted over any
connectors that are not being used.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Precaution for use
Always take some trial shots before actual shooting.
• When shooting important events (such as weddings), always take some trial shots and check that the
sound and images have been recorded properly before actual shooting.
Be sure to check and set the calendar and time zone.
• These settings affect the control of the recorded contents. Before making a recording, set and check the
calendar and time zone. (Page 35)
Panasonic makes no guarantees for your recordings.
• Please understand that Panasonic makes no guarantees for your recordings in cases where images and/
or sound were not recorded as you intended due to problems with the camera-recorder or SD/SDHC
Memory Cards.
Respect copyrights
• Copyright laws forbid the use of video and audio material you have recorded for any purpose other than
your own personal enjoyment. Remember that restrictions apply to the shooting of certain material even
if it is intended for private use.
Media that can be used in this unit
• SD/SDHC Memory Cards can be used in this unit. For details, refer to page 1ꢀ.
• SDXC Memory Cards cannot be used with this product.
Tripod receptacle
The tripod receptacle is a hole used to mount a tripod for the unit. (For details on mounting the tripod, refer
to the operating instructions for the tripod.)
• Compatible with the ISO1ꢀꢀꢀ (1/4) standard.
• The tripod mounting hole is 5.5 mm deep. Do not force the tripod screw beyond this depth.
You can damage the camera-recorder if you use any screw other than 1/4-ꢀ0UNC.
Camera
base
Tripod pin
Screw for
mounting
the unit
• When using the tripod, operations can be
performed more easily using a remote control
connected to the CAM REMOTE jack.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the IEEE1394 cable
Always heed the following instructions when connecting the IEEE1394 cable (not included.) (If it is
connected incorrectly, this may lead to the failure of this camera or external devices.).
• Connect or disconnect the IEEE1394 cable after switching off the power of all connected devices.
Devices with an earth terminal should be earthed (or connected to a shared GND) when using them.
• When connecting this camera to devices with a 4-pin terminal, connect this camera’s terminal (6-pin) in
advance.
• The terminal of the IEEE1394 cable has an orientation.
• When connecting the cable to an external device with a 6-pin IEEE1394 terminal, connect it as per with
the following configuration.
(Correct)
IEEE1394
terminal
End of the IEEE1394
cable
× (Incorrect)
IEEE1394
terminal
End of the IEEE1394
cable
For other usage notes, see page 8.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Precaution for use (continued)
SD Memory Cards compatible with this product
AVCHD mode
It is recommended that you use SD Memory Cards or SDHC Memory Cards of SD speed class ꢀ or
*
above, or the following Panasonic SD Memory Cards (correct as of August ꢀ010).
Speed class 4 or above is required for recording in PH mode or HA mode. SDXC Memory Cards cannot
be used with this product.
*
Photo shooting
Loading metadata
Card type
Recording capacity
Recording/playback
8 MB
16 MB
Cannot be used.
3ꢀ MB
64 MB
1ꢀ8 MB
ꢀ56 MB
Successful operation cannot be
guaranteed. Recording may be
suddenly terminated with certain
SD Memory Cards.
SD Memory
Card
51ꢀ MB
RP-SDV51ꢀ
RP-SDV01G
RP-SDM01G
1 GB
RP-SDV0ꢀG
RP-SDM0ꢀG
RP-SDP0ꢀG
ꢀ GB
RP-SDV04G
RP-SDM04G
RP-SDW04G
RP-SDP04G
4 GB
6 GB
8 GB
Can be used.
RP-SDM06G
RP-SDV08G
RP-SDM08G
RP-SDW08G
RP-SDP08G
SDHC Memory
Card
RP-SDM1ꢀG
RP-SDP1ꢀG
1ꢀ GB
16 GB
RP-SDV16G
RP-SDM16G
RP-SDW16G
RP-SDP16G
RP-SDV3ꢀG
RP-SDW3ꢀG
RP-SDP3ꢀG
3ꢀ GB
• Please see our support page at the following website for the latest information not included in these
operating instructions.
• This product is compatible with SD Memory Cards formatted under the SD-standard FAT1ꢀ and FAT16
formats, and with SDHC Memory Cards formatted under the FAT3ꢀ format.
• Only SDHC Memory Cards may be used for capacities of 4 GB or greater.
• 4 GB (or greater) memory cards without the SDHC logo are not based on the SD standard.
• Use this product to format the SD Memory Cards to be used. Formatting memory cards on computers
or other devices may cause recording to take longer than normal, or may cause cards to become
incompatible with this product. (Page ꢀ8 of Vol.ꢀ) (Use this product to reformat any cards that have
already been formatted on computers, etc.)
• Always install the relevant special adapter when using microSD/microSDHC cards with this product. (The
product will not operate correctly if only the adapter is inserted – always insert a memory card into the
adapter first.)
• MultiMediaCards cannot be used with this product.
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
DV mode
When shooting in DV mode, it is necessary to use SD Memory Cards or SDHC Memory Cards of speed
*
class 6 or above.
It is recommended that you use the following Panasonic SD Memory Cards (as of August ꢀ010).
SDXC Memory Cards cannot be used with this product.
*
Card type
Recording capacity
Recording/playback
8 MB
16 MB
Cannot be used.
3ꢀ MB
64 MB
1ꢀ8 MB
ꢀ56 MB
Cannot be used.
SD Memory
Card
51ꢀ MB
1 GB
RP-SDV51ꢀ
RP-SDV01G
RP-SDV0ꢀG
ꢀ GB
RP-SDV04G
RP-SDW04G
4 GB
8 GB
RP-SDV08G
RP-SDW08G
SDHC Memory
Card
RP-SDV16G
RP-SDW16G
16 GB
3ꢀ GB
RP-SDV3ꢀG
RP-SDW3ꢀG
• Please see our support page at the following website for the latest information not included in these
operating instructions.
• This product is compatible with SD Memory Cards formatted under the SD-standard FAT1ꢀ and FAT16
formats, and with SDHC Memory Cards formatted under the FAT3ꢀ format.
• Only SDHC Memory Cards may be used for capacities of 4 GB or greater.
• 4 GB (or greater) memory cards without the SDHC logo are not based on the SD standard.
• Use this product to format the SD Memory Cards to be used. Formatting memory cards on computers
or other devices may cause recording to take longer than normal, or may cause cards to become
incompatible with this product. (Page 76 of Vol.ꢀ) (Use this product to reformat any cards that have
already been formatted on computers, etc.)
• Always install the relevant special adapter when using microSD/microSDHC Memory cards with this
product. (The product will not operate correctly if only the adapter is inserted – always insert a memory
card into the adapter first.)
• MultiMediaCards cannot be used with this product.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Precaution for use (continued)
This product (SDHC-compatible device) is compatible both with SD Memory Cards and with
SDHC Memory Cards. SDHC Memory Cards may be used with SDHC Memory Card-compatible
devices, but cannot be used with devices that are only compatible with SD Memory Cards.
(Always check the relevant product’s operating instructions when using SDHC Memory Cards
with other devices.)
SDHC-compatible device
SD-compatible device
Can be used
Can be used
Cannot be used
Can be used
SDHC Memory Card
SD Memory Card
SDHC Memory Card
SD Memory Card
(SD speed class 6)
This refers to a class 6 speed standard (SD speed class) for the continuous writing of data between SD-
compatible devices and SD Memory Cards, as designated by the SD standards.
When the use of an SD speed class 6 card is recommended for SD-compatible products, this indicates
that stable recording operation can be achieved when using SD Memory Cards of class 6 and above.
• Speed class 4 or above is required for recording in AVCHD mode, or 6 or above for DV mode when
shooting with this camera.
Cautions for usage
• Do not allow dirt, water, or other substances to come into contact with the connector part on the
reverse of the card.
• Do not leave the card in the following places:
– In direct sunlight or in places of high humidity, e.g. close to heating equipment
– In highly humid or dusty locations
– In locations with high variations in temperature (condensation may appear on card)
– In places subject to static electricity or electromagnetic waves
• Store cards in bags or cases after use.
SDHC Memory Cards
●SDHC Memory Cards cannot be used with non-SDHC-compatible equipment.
●Ensure that all equipment is SDHC-compatible when using card with other devices.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Compatibility of recorded video
Shooting video in AVCHD mode
●Recorded video cannot be used with non-AVCHD-compatible equipment. For details, please see your
product’s operating instructions.
●Recorded video cannot be played back on non-compatible (non-AVCHD-compatible) equipment.
●Playback may not always be possible on all AVCHD-compatible equipment. Please use this product for
playback in such instances.
Shooting video in DV mode
●It is not compatible with AV devices fitted with a Panasonic SD Memory Card slot (DIGA, VERA, TV,
digital video camera).
●Video is recorded in AVI Type ꢀ file format and can be played back on computers using AVI Typeꢀ-
compatible media players.
About AVCHD
●AVCHD is a standard for the recording and playback of highly detailed, high-definition video.
●Video is compressed in the MPEG-4 AVC/H.ꢀ64 formats, and audio is recorded in Dolby Digital.
About DV
●It uses the AVI Type ꢀ file format and can play back with the DV compatible mode.
●Sound is recorded using the ꢀ ch uncompressed linear PCM system.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Outline
Using this Camera
This camera is mounted with a 1/4.1-type MOS sensor x 1ꢀ, and is a shoulder type camera recorder that
uses SD/SDHC memory cards for recording media.
It can record and play back SD images (DV mode) in addition to recording and playing back HD images
(AVCHD mode) with 1080 and 7ꢀ0 scan lines.
Shooting and playing back with this camera
MODE
AVCHD mode
• HD (hi-vision) shooting
• Shoots photos
CAMERA
• Connects to PCs (USB mode)
PB
• Prints photos with a printer (PictBridge)
PHOTO IN
AVCHD
DV
MODE
DV mode
• SD shooting
• DV (IEEE1394) input/output
CAMERA
PB
PHOTO IN
AVCHD
DV
■AVCHD mode
■DV mode
• Video shooting (CAMERA mode)
Shooting in auto mode (Page 37)
• Video shooting (CAMERA mode)
Shooting in auto mode (Page 37)
Shooting in manual mode (Page 54 of Vol.ꢀ)
• Playback (PB mode)
Shooting in manual mode (Page 5 of Vol.ꢀ)
• Photo shooting (PHOTO mode)
Shooting photos (Page 31 of Vol.ꢀ)
• Playback (PB mode)
Playing back clips (Page 40 of Vol.ꢀ)
Playing back photos (Page 4ꢀ of Vol.ꢀ)
• Other functions
Playing back clips (Page of 84 Vol.ꢀ)
• Other functions (DV IN mode)
DV (IEEE1394) output and input (Pages 73,
90 of Vol.ꢀ)
Connecting to a computer (USB mode)
(Page 53 of Vol.ꢀ)
Printing photos on a printer (PictBridge)
(Page 47 of Vol. ꢀ)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing and saving with external devices
SD/SDHC Memory Card (class 4
or above for PH and HA modes)
PC (Pages 51, 122 of Vol.2)
AVCHD mode
USB 2.0
USB 2.0
Printer (Page 47 of Vol.2)
MODE
CAMERA
PB
Video device / TV / monitor
(Pages 51, 52 of Vol.2)
HDMI cable (optional)
PHOTO
AVCHD
IN
DV
Video cable (BNC) (optional)
Audio cable (RCA) (optional)
• Select AVCHD with the
MODE switch, and then turn
on the camera.
Component cable (BNC) (optional)
There is no DV (1394) input/output function.
*
SD/SDHC Memory Card
(class 6 or above)
PC (Page 122 of Vol.2)
DV mode
IEEE1394 (DV) cable (optional)
A
ZEBR
BARS
E
MODE
DV tape device / memory card
recorder (backup, dubbing,
editing) (Pages 88, 90 of Vol.2)
CAMERA
PB
PHOTO
AVCHD
IN
DV
Video cable (BNC) (optional)
Audio cable (RCA) (optional)
Video device / TV / monitor
(Pages 87, 89 of Vol.2)
• Select DV with the MODE
switch, and then turn on
the camera.
Component cable (BNC) (optional)
There are no USB connection and HDMI output functions.
*
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
1
Battery
*
AC Adaptor
AC power supply cable/
DC cable
Wireless remote
control and battery
(CR2025)
Eye cup
Shoulder strap
CD-ROM
→ See “Attaching the
shoulder strap”.
(Page ꢀ7)
→ See “Fitting the eye
cup”. (Page ꢀ8)
The following accessories are attached to the unit.
Lens hood cap
Lens hood
Lens hood (inner)
Grip belt
XLR audio adaptor
cap
1 For part numbers for the battery, see “Optional accessories”. (Page 19)
• Please consult a retailer when purchasing additional accessories.
*
• After removing the package contents, discard the packaging materials appropriately.
• Some of the supplied accessories may not be manufactured in Japan.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional accessories
• Battery
VW-VBGꢀ60 (7.ꢀ V, ꢀ640/ꢀ500 (typ./min.) mAh: equivalent to accessory battery)
VW-VBG6 (7.ꢀ V, 5800/5400 (typ./min.) mAh: compatible with supplied battery charger)
• Tele conversion lens
VW-T4314H (See below for attachment instructions.)
• Wide conversion lens
VW-W4307H (See below for attachment instructions.)
Using tele conversion lenses, wide conversion lenses
Remove both the lens hood and lens hood (inner) before attaching an optional VW-T4314H tele
conversion lens or VW-W4307H wide conversion lens. For details on removing the lens hood, see page
ꢀ8.
Removing and attaching the lens hood (inner)
Remove
Attach
Align the grooves.
• Attach the ND filter and MC protector to the front of the lens hood (inner).
• Although you can attach both a filter and a conversion lens at the same time (such as attaching both
an ND filter and a tele conversion lens), we do not recommend it, as the corners of images may
appear darker (vignetting) during wide-angle zoom. (If you do attach both at the same time, remove
the lens hood (inner) first.)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of parts
Front side and rear side
1
2
3
4
9
4
10
11 12
POWER
ON
OFF
VIDEO
COMPONENT
LINE
MIC
LINE
MIC
AUDIO
OUT
CH
1
AUDIO
IN
ON
ON
OFF
MIC+48V
OFF
MIC+48V
CH
1
CH
2
CH
2
13
14 15
16
5
6
7
8
1
2
3
Handle zoom switch (Page 39)
Handle zoom lever (Page 39)
9
Viewfinder (Page 32)
10 Accessory shoe
Handle START/STOP button
(Pages 10, 59 of Vol.2)
11 START/STOP button (Page 37)
12 POWER switch (Page 30)
4
5
Shoulder belt installation hole (Page 27)
13 Lock button (Page 33)
REC CHECK/PHOTO SHOT button
(Page 38, Page 31 of Vol.2)
14 Battery release button (Page 26)
15 Battery compartment (Page 26)
16 Tally Lamp (REAR) (Page 30)
6
7
8
Zoom lever (Page 39)
Remote control sensor (Page 29)
Tally lamp (FRONT) (Page 30)
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Right Side
29
30 31
32
33
34
17 18 19 20
21
22
MONITOR
MODE
OIS
CH1
AUDIOLEVEL
CH2
CAMERA
PB
SPEED SEL
SHUTTER
PHOTO
AVCHD
IN
DV
BARS REC ZEBRA
DISP / MODE CHK
AUDIO SELECT
AUDIO IN
CH1
CH2
AUTO
MAN
FRONT
REAR
COUNTER
RESET/ TC SET
AUTO
MANUAL
MONITOR
MODE
DV
OIS
CH1
AUDIOLEVEL
CH2
CAMERA
PB
SPEED SEL
SHUTTER
PHOTO
AVCHD
IN
DV
FOCUS ASSIST FOCUS
IRIS
PUSH
DISP
/
MODE CHK
BARS REC ZEBRA
AUDIO SELECT
AUDIO IN
CH1
CH2
35 36 37 38 39 40 41 42 43
AUTO
MAN
FRONT
REAR
AUTO/
MANUAL
COUNTER
RESET/ TC SET
FOCUS ZOOM/
IRIS
WHITE
BAL
AUTO
MANUAL
USER
1
USER
2
USER
3
ONE
MENU
FUNC / EXEC
ENTER
MENU
FUNC
/
EXEC
PAGE / ADV
ENTER
44
45
PAGE
/
ADV
23 24 25 26
27 28
46
47
48 49
17 Built-in microphone
35 DISP/MODE CHK button
(Pages 11, 60 of Vol.2)
18 FOCUS ASSIST button (Pages 6, 55 of Vol.2)
19 FOCUS button (Pages 5, 54 of Vol.2)
20 IRIS dial (Pages 6, 55 of Vol.2)
36 BARS button (Pages 12, 61 of Vol.2)
37 ZEBRA button (Pages 10, 59 of Vol.2)
38 MODE switch (Page 37)
21 Diopter adjustment lever (Page 32)
22 Speakers
39 AUTO/MANUAL switch
(Page 37, Pages 5, 54 of Vol.2)
23 FOCUS ring (Pages 5, 54 of Vol.2)
24 RING switch (Pages 5, 54 of Vol.2)
25 WHITE BAL button (Pages 7, 56 of Vol.2)
26 USER1 - 3 button (Pages 12, 61, 107 of Vol.2)
27 Memory Card cover (Page 36)
40 AUDIO SELECT switch
(Pages 20, 70 of Vol.2)
41 COUNTER button (Pages 25, 73 of Vol.2)
42 RESET/TC SET button
(Pages 25, 73 of Vol.2)
28 ACCESS lamp (Page 36)
43 AUDIO IN CH1/CH2 switch
(Pages 18, 68 of Vol.2)
29 SHUTTER button (Pages 15, 65 of Vol.2)
44 HDMI terminal (Page 52 of Vol.2)
45 USB2.0 terminal (Page 51 of Vol.2)
46 MENU button (Page 40)
30 SPEED SEL -/+ button
(Pages 15, 65 of Vol.2)
31 OIS button (Pages 11, 60 of Vol.2)
32 MODE button
47 PAGE/ADV -/+ button (Pages 35, 37 of Vol.2)
48 Cursor button (Page 31)
(Page 31, Pages 31, 40, 42, 90 of Vol.2)
33 MONITOR LEVEL knob (Page 42 of Vol.2)
34 AUDIO LEVEL knob (Pages 20, 70 of Vol.2)
49 FUNC/EXEC button (Page 41)
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of parts (continued)
Left side
59
VIDEO
OUTPUT
50
COMPONENT
53
Y/
VIDEO
P
B
51
P
R
CAMREMOTE
ZOOM
S/S
52
FOCUS
IRIS
54
LINE
MIC
LINE
MIC
AUDIO
OUT
CH
1
AUDIO
IN
ON
ON
OFF
MIC+48V
OFF
MIC+48V
CH
1
CH
2
CH
2
60
61
55 56
57 56 58
50 OUTPUT switch (Pages 52, 89 of Vol.2)
56 MIC + 48 V ON/OFF switch
(Pages 19, 69 of Vol.2)
51 VIDEO terminal (BNC)/ COMPONENT OUT
(Y/PB/PR) terminal (BNC)
57 XLR input (CH1/CH2) terminal
(Pages 19, 69 of Vol.2)
(Pages 52, 89 of Vol.2)
52 CAM REMOTE jacks
58 AUDIO OUT (CH1/CH2) terminal
(Pages 52, 87, 89 of Vol.2)
*
FOCUS/IRIS (3.5 mini jack)
You can connect a remote control unit to control
the FOCUS and IRIS (aperture). IRIS (aperture)
control beyond OPEN is performed via gain
adjustment, and can be set up to the standard
gain setting.
59 Left and right position lock ring (Page 32)
60 EXT MIC terminal (Pages 50, 86 of Vol.2)
61 Grip belt (Page 27)
Do not connect any equipment except the
ZOOM S/S (2.5 mm super mini jack)
You can connect a remote control unit to control
zoom and start/stop of recording.
*
remote controller to the remote control jack.
Connecting any equipment other than the
remote control may cause the image brightness
to change and/or the images to appear out of
focus.
53 DV terminal (Page 88 of Vol.2)
54 Input audio selection switch
(Pages 19, 69 of Vol.2)
55 PHONES (headphone) terminal
(Pages 50, 86 of Vol.2)
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
To use the remote control, set the IR REMOTE item on the OTHER FUNCTIONS menu to ON. The default
setting for this item is OFF. (Page 110 of Vol.ꢀ)
1
2
3
EXT. DISPLAY button (Pages 49, 85 of Vol.2)
DATE/TIME button (Pages 49, 85 of Vol.2)
PHOTO SHOT button (Page 31 of Vol.2)
START/
STOP
PHOTO
SHOT
EXT
DISPLAY
4
5
1
DATE/
TIME
ZOOM
2
3
6
8
Performs only the PHOTO SHOT function of
the REC CHECK/PHOTO SHOT button on the
camera.
VOL
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
7
9
11
7
9
11
4
5
START/STOP button (Page 37)
ZOOM/VOL buttons (Page 39)
10
MENU
14
12
13
The sound volume of the camera cannot be
adjusted using the remote control.
ENTER
15
6
7
8
9
PLAY button (Pages 41, 84 of Vol.2)
SEARCH buttons (Pages 40, 41, 84 of Vol.2)
PAUSE button (Pages 40, 41, 84 of Vol.2)
STILL ADV buttons (Pages 41, 84 of Vol.2)
Remote control usable range (Page ꢀ9)
10 STOP button (Pages 40, 84 of Vol.2)
11 SKIP buttons (Pages 40, 84 of Vol.2)
12
button
Does not function with this camera.
13 OPERATION buttons
Same function as the cursor button (menu
operation) on the camera.
14 MENU button
Same function as the MENU button on the
camera.
15 ENTER button
Confirms menu and item selections.
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Recharging the battery
Recharging
The battery does not come ready charged when
the camera is purchased. Charge the battery
before use.
It is recommended that you keep one extra battery
as a spare.
■Charging time and available recording time
(Approx.)
Maximum
Battery
model
Voltage/
capacity
Charging
time
continuous
recording time
7.ꢀ V/
Connect the power cable to the AC adaptor.
VW-VBGꢀ60 ꢀ640/ꢀ500
(included) (typ./min.)
mAh
Approx.
170 min.
Approx.
85 min.
1
Disconnect the DC cable.
(Battery cannot be charged if DC cable is
connected.)
7.ꢀ V/
VW-VBG6 5800/5400
Approx.
Approx.
(optional)
(typ./min.)
mAh
350 min.
170 min.
Insert until fully in place.
• The figures in the table above are guidelines
for use in normal temperature conditions
(temperature ꢀ5 °C (77 °F), humidity 60 %).
Charging may take longer in higher or lower
temperatures.
Insert the battery.
2
• Charging may take longer if the battery has not
been in use for a long period of time.
• The maximum continuous recording times given
here assume that the camera is recording in DV
mode with no external devices connected.
• Available recording time may vary according to
usage conditions.
Charging lamp [CHARGE]
Align the battery with the
mark and insert fully.
• Charging times are based on charging batteries
from an empty state.
■Charging lamp
On: Charging in progress
Off: Charging complete
Flashing: See below
■If charging lamp is flashing
Check that there is no dirt, dust, or other
substances attached to the connectors on the
battery or AC adaptor, and ensure that the adapter
has been connected correctly.
• If there is dirt or dust on the connectors,
disconnect the power plug from the socket before
cleaning.
• If the charging lamp continues to flash, there
may be a fault with the battery or the AC adaptor.
Please consult with the place of purchase.
ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
■Remaining battery capacity displays
When using Panasonic-manufactured batteries
compatible with this product, the remaining battery
capacity is displayed in minutes.
90min.
Time remaining will be displayed after a brief
pause.
• The battery display will change
• Keep metal objects (such as necklaces and
hairpins) away from the battery.
Short-circuiting may occur across the
terminals, causing the battery to heat up,
and you may seriously burn yourself if you
touch the battery in this state.
• The battery becomes hot while it is being used
or charged. The camera-recorder itself also
becomes hot during use.
• The recordable time reduces if you repeatedly
start and stop recording.
• The battery takes longer to charge when it is
warm.
→
→
→
→
as battery capacity decreases.
will be
displayed in red when less than 3 minutes are
remaining, and
is empty.
will flash when the battery
• Remaining battery capacity may not be displayed
correctly when using in high or low temperatures,
or when the battery has not been used for a
long period of time. To ensure that remaining
battery capacity is displayed correctly, use the
battery completely from a fully-charged state,
and charge the battery again. (Remaining battery
capacity may still not be displayed correctly if the
battery has been used for long periods in high
or low temperatures, or if the battery has been
recharged a large number of times.)
• The AC adaptor can interfere with radio
reception so keep radios at least 1 meter away
from it.
• The AC adaptor may make some noise when
you are using it, but this is normal.
• Battery cannot be recharged when the DC
cable is connected to the AC adaptor.
• The remaining battery capacity display is a
guideline and may change according to usage
conditions.
• The remaining battery capacity display will
momentarily disappear when switching between
modes, when conducting REC CHECK
operations or when changing the LCD brightness
since the capacity is recalculated at these times.
• Not displayed when using AC adaptor.
• The maximum time display for the remaining
battery capacity is 999 minutes.
• If the remaining battery capacity exceeds 999
minutes, the remaining time is displayed in green.
This display does not change until the remaining
time reaches 999 minutes or below.
ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
Power sources
Using the battery
Installation
Removal
Insert the battery until it clicks into place.
Set the POWER switch to OFF, and check
that the mode lamp is off.
1
2
Remove the battery while pressing the
battery release button.
• The lock can be released and the battery
removed.
Using the AC adaptor
Installation
Removal
Connect the DC cable to the AC adaptor.
Set the POWER switch to OFF, and check
that the mode lamp is off.
1
2
1
2
3
Plug the AC power supply cable into the
power outlet.
Remove the DC cable’s battery connector
while pressing the battery release button.
Insert the DC cable’s battery connector until
it clicks into place.
3
Disconnect the AC power supply cable from
the power outlet.
%1/210'06
• Battery cannot be recharged when the DC
cable is connected to the AC adaptor.
•
Disconnect the AC power supply cable from the
power outlet when the unit is not going to be used.
DC cable’s battery
connector
CAUTION:
• This apparatus can be operated at a voltage in
the range of 110 – ꢀ40 V AC.
Voltages other than 1ꢀ0 V are not intended for
U.S.A. and Canada.
Operation at a voltage other than 1ꢀ0 V AC may
require the use of a different AC plug.
Please contact either a local or foreign
Panasonic authorized service center for
assistance in selecting an alternate AC plug.
ꢀ6
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the grip belt
Adjust the grip belt to suit your hand, and hold it
correctly.
• When loosening the belt, please take care so
that the belt does not come away from the grip
belt stopper.
Open the belt cover and loosen the belt.
1
Grip belt stopper
Work your hand through the grip belt and
fasten the belt.
2
• Slip your hand through the belt as far as
it goes.
• Tighten up the belt so that your hand
remains firmly in place.
Attaching the shoulder strap
Attach the shoulder strap and use it as a precaution against dropping the camera.
Thread the belt through the shoulder belt
installation hole.
Install the belt on the other shoulder belt
installation hole.
1
2
Shoulder belt
installation hole.
• Thread the belt through the fastener
after threading through the shoulder belt
installation hole. At least ꢀ cm of the belt
must extend from the fastener.
ꢀ7
Download from Www.Somanuals.com. All Manuals Search And Download.
Detaching and attaching the lens hood
Detaching the lens hood
• Turn the lens hood counterclockwise to detach it.
Attaching the lens hood
• Orient the lens hood with the arrow mark on top,
rotate the hood counterclockwise (approx. 14˚) to
align the arrow with the one on the camera, and
then slide the hood onto the camera.
• Rotate the lens hood clockwise to attach it.
• Be sure to attach the lens hood cap to protect the
lens when not in use.
Lens hood
Attaching the lens hood cap
The lens can be covered by attaching the lens
hood cap provided to the lens hood.
Lens hood cap
Fitting the eye cup
To attach the eye cup, align the projections on the
eye cup holder and eye cup, and fit the holder and
eye cup together.
Eye cup
Projection
Eye cup holder
• Turning the eye cup after attaching it to its holder
may cause the holder to become disengaged.
ꢀ8
Download from Www.Somanuals.com. All Manuals Search And Download.
The remote control
Insert the battery
Remote control usable range
Push the catch in the direction shown by
arrow ① to remove the holder.
The distance between the remote control and the
unit’s remote control sensor: Within approx. 5 m
Angle: Approximately 15° upward,
approximately 10° downward,
1
approximately 15° leftward, or
approximately 15° rightward
(Except when optional accessories are
attached)
Insert the battery with the “+” marked side
facing up.
Remote control
sensor
2
Return the holder to its original position.
3
• When the battery (CRꢀ0ꢀ5) has run out, replace
it with a new one. (The battery lasts about one
year, depending on the frequency of use.)
If the remote control unit fails to work even when
it is operated near the camera-recorder’s remote
control sensor, the battery has run out.
• The remote control is intended for indoor
operation. Outdoors or under strong light, the unit
may not operate properly even within the usable
ranges.
• The default setting for this item is OFF. To use
the remote control, set the IR REMOTE item
on the OTHER FUNCTIONS menu to ON.
(Page 110 of Vol.ꢀ)
• Keep the battery out of the reach of children.
ꢀ9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Turn on/off the camera
While pressing the lock release button, move the
POWER switch to ON or OFF.
Mode lamp
CAMERA
PB
Turn on the camera:
The mode lamp (CAMERA) lights red (camera
mode), and the camera enters recording standby
mode.
PHOTO IN
AVCHD
DV
Turn off the camera:
The mode lamp (CAMERA) goes out.
• Energy-saving mode
POWER
ON
POWER switch
Depending on the setting made for the POWER
SAVE item of the OTHER FUNCTIONS screen
in the settings menu, the following will apply if
no designated operations* are performed for
approximately five minutes in the recording standby
modes of CAMERA mode and PHOTO mode (when
an SD Memory Card has been inserted while using
the battery).
Set the POWER switch to the
ON position while pressing the
lock release button.
The CAMERA lamp lights
(red), and the camera enters
recording standby mode.
OFF
Lock release button
ON: The camera recorder turns off automatically.
OFF: Does not switch OFF the camera.
See the setup menus, POWER SAVE
(Page 111 of Vol.ꢀ) for details.
*
Tally lamp
You can set the tally lamp to light in the following
situations by setting the REC LAMP item
(Page 110 of Vol.ꢀ) in the OTHER FUNCTIONS
screen to OFF.
The tally lamp light can be switched to FRONT,
REAR or BOTH with the setting menu. For more
details, refer to the setting menu REC LAMP item
(Page 110 of Vol.ꢀ).
Tally lamp (REAR)
LINE
MIC
LINE
MIC
AUDIO
OUT
CH
1
AUDIO
IN
ON
ON
OFF
MIC+48V
OFF
MIC+48V
CH
1
CH
2
CH
2
• Battery is low (flashes 4 times per second)
• Available SD Memory Card capacity is low
(flashes 4 times per second)
Tally lamp (FRONT)
• Remaining battery capacity is low
(flashes once per second)
• Remaining memory of the SD Memory Card is
low (flashes once per second)
In addition, the location set for the REC LAMP
item will flash when receiving commands from the
remote control.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the cursor button
This unit has a cursor button for selecting menu items and performing play back operations.
Basic operations
The following describes operations on the menu screen and selection of files on the thumbnail view screen
etc.
ENTER
cursor button
Select an item by pressing the up, down, right,
or left button of the cursor button and enter
the selection by pressing the ENTER button.
ENTER
ENTER
Press the up, down, right, or left button of the
cursor button to select an item or a scene, and
press the ENTER button to enter it.
Menu screen operations
Playback mode (PB mode only)
Press the MENU button to display the menu.
Press the MODE button and switch to PB
mode.
1
1
• The thumbnail menu is displayed when in
DV or PB mode. Press and hold the MENU
button to display the normal menu.
Select a clip or photo to play back with the
cursor button, and press the ENTER button.
2
3
Select an item by pressing the ENTER
button.
• Perform the same operation to select
additional items or to set numerical values.
2
3
Operate by pressing the up, down, right, or
left button of the cursor button.
Press the MENU button to exit the menu
screen.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the viewfinder
This camera has a viewfinder which uses a
retractable 69 mm (ꢀ.7 inch) LCD.
Adjust the diopter adjust ment lever until
images in the viewfinder are clear.
4
• The brightness and hue may differ between
the images appearing on the viewfinder (LCD
monitor) and those displayed on a TV monitor.
To see how the final images will appear, check
them on a TV monitor.
Eye cup
Using the viewfinder
Set the POWER switch to ON, and check
that images appear in the viewfinder.
1
Diopter
adjustment
lever
ヱヰヸユン
ヰワ
ヰョョ
Do not point the viewfinder directly at the
sun.
Adjust the angle of the viewfinder to a
2
convenient viewing position.
• The viewfinder can be rotated 180° towards
the lens and 90° towards the opposite
direction.
• Doing so may damage internal components.
• When using the camera with the viewfinder
opened, sunlight passing through the EVF lens
may be magnified. Flammable objects placed
in the area of magnified light may ignite.
You can record yourself.
Loosen the left and right position lock ring,
and adjust the horizontal position.
3
•
When you have decided the position, tighten
and secure the left and right position lock ring.
3ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using as a LCD monitor
Emphasizing outlines
Open the eye piece to use as a LCD monitor.
When EVF DTL is assigned to one of the USER
buttons 1 to 3, you can press that button to
emphasize the outlines of images in the viewfinder
and make focus alignment easier.
Emphasizing the outlines does not effect the
images you shoot.
Opening the eye piece
Open the eye piece while pressing the lock button
at the same time.
Set the POWER switch to ON. (Page 30)
1
Press the MENU button.
• Menu operation (Page 40)
2
• Operations may also be performed
using buttons on the remote control that
correspond to those on the camera. For
details, see “Description of parts (Remote
control)”. (Page ꢀ3)
Eye piece
Lock button
Select either the USER1 SW, USER2 SW
3
or the USER3 SW item in the setting menu
SW&DISP SETUP screen, and press the
ENTER button.
Select EVF DTL and press the ENTER
button.
4
EVF DTL is assigned to the selected USER
button.
Closing the eye piece
Close the eye piece by pressing it until it clicks into
place.
In CAMERA mode or PHOTO mode, press
5
the USER button assigned to EVF DTL.
“EVF DTL ON” appears in the center of the
screen for about ꢀ seconds.
To release the setting, press the USER button
assigned to EVF DTL again, and “EVF DTL
OFF” appears in the center of the screen for
approximately ꢀ seconds.
• Rotating the viewfinder with the eye piece
open may result in damage to the eye piece or
your fingers getting caught.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the viewfinder (continued)
Adjusting the screen display
• The viewfinder display can be in color or black
and white. (See the setup menus, SW&DISP
SETUP screen, EVF COLOR.) The resolution
is the same for both of them.
• The menu will be displayed in color even if
black and white is selected.
Set the POWER switch to ON. (Page 30)
1
Press the MENU button.
• Menu operation (Page 40)
2
• Operations may also be performed
using buttons on the remote control that
correspond to those on the camera. For
details, see “Description of parts (Remote
control)”. (Page ꢀ3)
Select YES for the EVF SET item in the
setting menu SW&DISP SETUP screen, and
press the ENTER button.
3
Press the up or down button of the cursor
button to select the item you want to set,
and then press the ENTER button.
4
Press the left or right button of the cursor
button to adjust the numerical value of the
selected item.
5
Select ENTER and press the ENTER button.
• Select EXIT and press the ENTER or the
MENU button to finish configurations.
6
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the calendar
The CLOCK SET value is recorded in the contents
(clip), and affects the sequence of playback of the
thumbnails. The “SET DATE AND TIME” message
appears when you turn on the camera for the first
time. Before carrying out recording, be sure to
check and set CLOCK SET and TIME ZONE. This
shows you how to adjust the calendar to 14:30 on
May 13, ꢀ010.
Setting the clock
Set the POWER switch to ON. (Page 30)
1
Press the MENU button.
• Menu operation (Page 40)
2
• Operations may also be performed
using buttons on the remote control that
correspond to those on the camera. For
details, see “Description of parts (Remote
control)”. (Page ꢀ3)
Setting the time zone
Set the POWER switch to ON. (Page 30)
1
Select YES for the CLOCK SET item in the
setting menu OTHER FUNCTIONS screen,
and then press the ENTER button.
3
Press the MENU button.
• Menu operation (Page 40)
2
• Operations may also be performed
using buttons on the remote control that
correspond to those on the camera. For
details, see “Description of parts (Remote
control)”. (Page ꢀ3)
Select YES for the TIME ZONE item in the
setting menu OTHER FUNCTIONS screen,
and then press the ENTER button.
3
Select the item you want to set with the left
or right button of the cursor button, and
press up or down to set numerical values.
4
Press the up or down of the cursor button to
select the difference from Greenwich Mean
Time.
4
Repeat the procedure from step 4 to set the
remaining items.
• The date can be set to any date between
January 1, ꢀ010 and December 31, ꢀ036.
• “--.--.----” is displayed for any date beyond
December 31, ꢀ036.
5
6
• The time is displayed in ꢀ4-hour format.
• The factory default setting is +0:00.
Select EXIT when you are finished
configuring items, and press the ENTER or
MENU button to finish setting.
Select ENTER and press the ENTER button.
5
• The clock can vary in accuracy, so check that
the time is correct before shooting.
• When using the camera overseas, do not
set the CLOCK SET option to the local time,
but enter the time difference from Greenwich
Mean Time using the TIME ZONE option
instead. (Page 111 of Vol.ꢀ)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic shooting operations
Preparing for recording
•
Do not perform any of the following operations
while the SD Memory Card ACCESS lamp is
flashing.
Performing these operations may damage the
SD Memory Card or its contents, or cause the
camera to fail to operate correctly.
� Opening the card door and removing the SD
Memory Card
Set the camera’s power switch to OFF.
(Page 30)
1
• Check that the mode lamp is off.
Slide the card cover upwards to open.
2
AUTO
M
AN
U
A
L
� Switching off the power
M
� Removing the battery
EN
U
FU
� Connecting or disconnecting the USB
connection cable
N
C
/E
X
E
C
ENTER
� Shaking or striking the camera
• Always format SD Memory Cards that have
been used in other devices when first using
them with this camera. (Pages ꢀ8, 76 of Vol.ꢀ)
• If “CHECK CARD” is displayed on the
viewfinder, please remove the SD Memory
Card and insert it again.
PAGE/ADV
ACCESS lamp
· Flashes during SD
Memory Card access
(recognition, recording,
playback, deletion, etc.).
For details, see “SD
Memory Card ACCESS
lamp”.
SD Memory Card ACCESS lamp
This lamp lights or flashes during memory card
access.
Lit: Card inserted, read/write possible
Flashing (fast): Recognizing
Flashing (slow): Accessing (during recording/
playback/reading)
Fully insert an SD Memory Card into the
card slot.
• Insert the card in the direction shown until it
clicks into place.
3
AUTO
M
A
N
U
A
L
Off: Card not inserted, unformatted card inserted,
write protected card inserted
M
EN
U
FU
N
C
/E
AUTO
X
EC
M
AN
U
A
L
ENTER
M
EN
U
FU
N
C
/E
X
E
C
PAGE/ADV
ENTER
Close the SD Memory Card cover.
• Ensure that the cover firmly clicks into place.
PAGE/ADV
4
SD Memory Card access lamp
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Shooting in auto mode
Select the recording mode (AVCHD mode or
DV mode) with the MODE switch.
1
Turn the POWER switch to ON. (Page 30)
• Check that the mode lamp (CAMERA) is
lighted red.
2
3
Switch the AUTO/MANUAL switch to AUTO
to select auto mode.
Mode lamp
•
appears in the upper area of the
viewfinder.
• The focus, shutter speed, gain, iris, and
white balance are adjusted automatically.
In addition, if the AUTO SW item in the
setting menu SW&DISP SETUP screen is set
to FACE DETECT ON, focus is automatically
aligned on faces detected in the image and
brightness is adjusted for optimal results.
Lock release button
A
appears when FACE DETECT ON is set.
•
Up to 15 face detection frames can be displayed
on the screen at one time. Larger frames and
frames closer to the center have priority.
• When FACE FRAMING is set to ALL and
multiple subjects are detected, only the
frame on which focus is aligned is displayed
in orange. All other frames are displayed in
gray.
• Primary (priority) frames
The primary frame is displayed in orange.
Focus is automatically aligned to the primary
frame, and the brightness is adjusted.
When you press the REC CHECK/PHOTO
SHOT button halfway in PHOTO mode,
focus is aligned to the primary frame.
When focus is aligned, the primary frame
turns green.
Press the START/STOP button (Red) to start
shooting.
4
• Press again to enter recording standby
mode.
•
Shooting is not possible when a menu screen
is displayed. First, close the menu screen,
and then press the START/STOP button.
• Shooting stops when the SD Memory Card
cover is opened during shooting.
(Continued on the next page)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic shooting operations (continued)
Checking photos taken (REC CHECK)
• The images shot from when shooting starts
until it is stopped are recorded as one clip.
• When recording is paused after a short period,
a small amount of time may be required after
pressing the START/STOP button to stop
recording before writing to the SD Memory
Card is terminated.
This means that operations cannot be
accepted if the START/STOP button is
pressed immediately.
Press the REC CHECK/PHOTO SHOT button
(Page ꢀ0) while in recording standby mode. The
last two seconds of video and audio will be played,
and the camera returns to recording standby
mode.
• Only the POWER and START/STOP buttons are
operable during REC CHECK.
• The REC CHECK images are also recorded
when a device is connected to the camera and
backup images have been recorded.
• The REC CHECK function does not work when
PB has been selected as the operation mode or
when connected to a computer.
• This function also does not work after recording
if the REC FORMAT has been changed, or if the
camera has been set to CAMERA mode after
having switched to another mode (PB, PHOTO,
etc.).
• The camera will read information from the
SD Memory Card immediately after the card
is inserted. Press the START/STOP button
to begin recording after
(pause: green)
is displayed in the operation status display.
(Page 9ꢀ of Vol.ꢀ)
AVCHD mode:
• The camera’s factory default setting is PH
mode 1080/60i recording.
(To view current setting status: Page 11 of
Vol.ꢀ)
• This function does not work if the SD Memory
Card is removed and reinserted.
• The upper limit for the number of clips which
can be recorded on a single SD Memory Card
is 900. (However, this number may exceed
900 clips at times such as when shooting
immediately after the POWER switch has been
set to ON.)
• Mosaic-like noise may appear on the playback
screen under the following shooting conditions:
� When there are complex patterns in the
background
� When the camera is moved in large motions
or when it is moved very quickly
�
When a fast-moving subject has been recorded
(and especially when HE has been set as the
recording mode)
DV mode:
• The camera’s factory default setting is 480/60i
recording.
• The upper limit for the number of clips which
can be recorded on a single SD Memory Card
is 999.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the zoom function
This camera has a 1ꢀ x optical zoom function. Use
the zoom lever, handle zoom lever or assign zoom
functions to the FOCUS ring to perform zoom
operations.
• With the HANDLE ZOOM item in the setting
menu SW&DISP SETUP screen, you can reset
the speed allocated to the handle zoom switch
(Factory default settings are 1: low-speed (L);
ꢀ: medium-speed (M); and 3 high-speed (H)).
Zoom lever
Press the T side of the zoom lever to zoom in, or
the W side to zoom out.
On the remote control
Press the ZOOM/VOL buttons to zoom.
• Zoom speed is fixed at medium.
START/
STOP
PHOTO
SHOT
EXT
DISPLAY
DATE/
TIME
ZOOM
Zoom
VOL
ZOOM/VOL buttons
SEARCH
PLAY
SEARCH
• To use the remote control, set the IR REMOTE
item on the OTHER FUNCTIONS menu to ON.
(Page 110 of Vol.ꢀ)
Handle zoom lever
Press the T side of the handle zoom lever to zoom
in, or the W side to zoom out.
• When using a macro range and AF or MF on
the focus control information display appears
in reverse black and white, zooming may
cause the image to become unfocused.
Digital zoom function
By setting D.ZOOM to any of the USER 1 - 3
buttons, you can use the camera’s digital zoom
function. (Page 107 of Vol.ꢀ)
With each press of the USER button to which
D.ZOOM has been allocated, the digital zoom ratio
will be switched between OFF (x 1)→(x 2)→(x 5)→
(x 10)→OFF.
• The higher the zoom ratio setting, the poorer the
image quality.
• For all settings other than OFF (x 1), the current
zoom ratio will be displayed in the viewfinder.
• The digital zoom function can only be used with
the following recording formats.
The handle zoom lever speed can be switched
between 3 levels with the handle zoom switch.
HANDLE ZOOM
1
2
3
AVCHD mode : 1080/60i, 7ꢀ0/60P
DV mode: 480/60i
• The digital zoom function cannot be used in
PHOTO mode.
• The digital zoom function cannot be used with
interval recording.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the setup menus
Use the setup menus to change the settings to
suit the scenes you are shooting or what you are
recording.
Select the item you want to set with the up
or down button of the cursor button, and
press the ENTER button.
3
4
• To return to a previous screen, press the left
button of the cursor button.
ヮユワヶ
ョヶワヤチバチユヹユヤ
Select the up or down button on the cursor
button to set numerical values, and press
the ENTER button.
ユワヵユン
• To change numerical values, press the up,
down, left or right button on the cursor button
to change the values.
ヱモヨユチバチモュヷ
• To return to a previous screen, press the left
button on the cursor button.
Using the menus
Repeat steps 3 – 4 to set any other items.
To complete settings, select EXIT and press the
ENTER or the MENU button.
5
6
• The menu items indicated in the gray
characters cannot be changed its settings.
Repeat steps 2 – 4 to set any other
functions.
To complete settings, select EXIT and press the
ENTER or the MENU button.
When the unit is in other than playback or
1
recording mode, press the MENU button.
The following is displayed on the viewfinder.
• Press and hold the MENU button when set to
PB mode (thumbnail display) of DV mode.
Select the function you want to set with the
up or down button of the cursor button, and
press the ENTER button.
2
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Function Menu
Press the ENTER button when the item has
been set.
4
5
The Function Menu is an expanded function of the
setting menu that allows you to configure WHITE
BALANCE, SYNCRO SCAN, SELF TIMER,
I.EXPOSURE, and SKIN TONE DTL settings.
Press the FUNC/EXEC button to close the
Function Menu.
■Operation in the thumbnail display screen
(AVCHD mode only)
Each press of the FUNC/EXEC button moves the
cursor in the thumbnail display screen of PB mode.
Press the FUNC/EXEC button while in
CAMERA or PHOTO mode.
The items that appear may vary depending on
the mode and settings.
1
Operating menu
Thumbnail
Select the left or right button of the cursor
button, and press ENTER.
2
To change numerical values, press the up or
down button of the cursor button to select
the values, and then press ENTER.
3
Cursor moves.
Initializing the menu settings
You can return the setting values for each item
to their factory default settings with the MENU
INIT item in the setting menu OTHER FUNCTION
screen.
To initialize menu settings, set this item to YES,
and then press the ENTER button.
You can set the following items in the Function
Menu.
Icon
Item
Display mode Page
Ach
Bch WHITE
It is not
displayed
Pages
7, 56 of
,
Setting values for the following items are not
initialized.
• Time code values
BALANCE
when in AUTO Vol.ꢀ
mode.
• User information values
• CLOCK SET and TIME ZONE
• OPERATION TIME
SYNC
SYNCRO
SCAN
It is not
displayed
when in AUTO Vol.ꢀ
mode.
Pages
17, 67 of
SELF TIMER PHOTO
Page 105
of Vol.ꢀ
I.EXPOSURE It is not
displayed
Page 10ꢀ
of Vol.ꢀ
when in AUTO
mode.
SKIN TONE
DTL
It is not
Page 10ꢀ
of Vol.ꢀ
displayed
when in AUTO
mode.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menu structure
CAMERA mode menu
Video recording menu
SCENE FILE
FILE SELECT
LOAD/SAVE/INIT
DETAIL LEVEL
V DETAIL LEVEL
DETAIL CORING
CHROMA LEVEL
CHROMA PHASE
COLOR TEMP
MASTER PED
A.IRIS LEVEL
DRS
(Page 101 of Vol.ꢀ)
GAMMA
KNEE
MATRIX
SKIN TONE DTL
RECORD SETUP
(Page 103 of Vol.ꢀ)
REC FORMAT
ASPECT CONV
(DV mode only)
PREREC MODE
TIME STAMP
SW&DISP SETUP
(Page 107 of Vol.ꢀ)
HANDLE ZOOM
IRIS DIAL
USER1 SW
USERꢀ SW
USER3 SW
FOCUS ASSIST SW
RING SW
AUTO SW
INTERVAL REC
TC MODE
TCG
TC PRESET
UB MODE
SMOOTH ZOOM STOP
CAM GAIN LIMIT
FACE FRAMING
ZEBRA DETECT
MARKER
SAFETY ZONE
REC COUNTER
VIDEO OUT OSD
DATE/TIME
DATE FORMAT
LEVEL METER
LENS STATUS
CARD & BATTERY
OTHER DISPLAY
EVF BACKLIGHT
EVF SET
(DV mode only)
UB PRESET
MIC GAIN1
MIC GAINꢀ
META CARD READ
(AVCHD mode only)
META DATA REC
(AVCHD mode only)
USER CLIP NAME
(AVCHD mode only)
META DATA PROP
(AVCHD mode only)
CLIP COUNTER RST
(AVCHD mode only)
META INITIAL SET
(AVCHD mode only)
SELF SHOOT
EVF COLOR
OTHER FUNCTIONS
(Page 110 of Vol.ꢀ)
CARD FORMAT
IR REMOTE
DV CONTROL
(DV mode only)
DV CMD SEL
(DV mode only)
REC LAMP
BEEP SOUND
CLOCK SET
TIME ZONE
OPTION MENU
1394 STATUS
1394 CONFIG
(DV mode only)
*
(Page 113 of Vol.ꢀ)
Display it by pressing the MENU button while
pressing down the DISP/MODE CHK button.
*
POWER SAVE
HDMI OUT SEL
(AVCHD mode only)
CMPNT OUT SEL
(AVCHD mode only)
DOWNCON MODE
(AVCHD mode only)
TV ASPECT
VIDEO SETUP
AUDIO OUT
MENU INIT
LANGUAGE
OPERATION TIME
4ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
PHOTO mode menu
DV IN mode menu
Photo recording menu
CAMERA SETUP
DV IN menu
I.EXPOSURE
RECORD SETUP
(Page 103 of Vol.ꢀ)
1394 TC REGEN
TC MODE
(Page 10ꢀ of Vol.ꢀ)
DETAIL LEVEL
CHROMA LEVEL
A.IRIS LEVEL
SKIN TONE DTL
TCG
TC PRESET
1394 UB REGEN
UB MODE
UB PRESET
DV IN PRESET
PICTURE
(Page 105 of Vol.ꢀ)
PICTURE SIZE
QUALITY
ASPECT RATIO
SELF TIMER
SHTR SOUND
PLAY SETUP
(Page 106 of Vol.ꢀ)
REPEAT PLAY
RESUME PLAY
SW&DISP SETUP
(Page 107 of Vol.ꢀ)
HANDLE ZOOM
IRIS DIAL
SW&DISP SETUP
(Page 107 of Vol.ꢀ)
USER1 SW
USERꢀ SW
USER1 SW
USER3 SW
USERꢀ SW
USER3 SW
FOCUS ASSIST SW
RING SW
AUTO SW
SMOOTH ZOOM STOP
CAM GAIN LIMIT
FACE FRAMING
ZEBRA DETECT
MARKER
REC COUNTER
VIDEO OUT OSD
DATE/TIME
DATE FORMAT
LEVEL METER
CARD & BATTERY
OTHER DISPLAY
EVF BACKLIGHT
EVF SET
EVF COLOR
GUIDE LINES
HISTOGRAM
VIDEO OUT OSD
DATE/TIME
DATE FORMAT
LENS STATUS
CARD & BATTERY
OTHER DISPLAY
EVF BACKLIGHT
EVF SET
OTHER FUNCTIONS
(Page 110 of Vol.ꢀ)
CARD FORMAT
IR REMOTE
BEEP SOUND
CLOCK SET
TIME ZONE
POWER SAVE
TV ASPECT
VIDEO SETUP
AUDIO OUT
MENU INIT
LANGUAGE
SELF SHOOT
EVF COLOR
OPERATION TIME
OTHER FUNCTIONS
(Page 110 of Vol.ꢀ)
CARD FORMAT
IR REMOTE
1394 STATUS
1394 CONFIG
OPTION MENU
REC LAMP
(DV mode only)
*
BEEP SOUND
CLOCK SET
TIME ZONE
POWER SAVE
HDMI OUT SEL
CMPNT OUT SEL
TV ASPECT
MENU INIT
LANGUAGE
OPERATION TIME
(Page 113 of Vol.ꢀ)
Display it by pressing the MENU button while
pressing down the DISP/MODE CHK button.
*
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menu structure (continued)
PB mode menu
Clip playback menu
Photo playback menu (AVCHD mode only)
PLAY SETUP
REPEAT PLAY
RESUME PLAY
PICT. SETUP
SCENE PROTECT
(Page 106 of Vol.ꢀ)
(Page 106 of Vol.ꢀ)
DPOF SET
DELETE
OPERATION
(Page 106 of Vol.ꢀ)
CLIP PROTECT
(AVCHD mode only)
DELETE
SW&DISP SETUP
(Page 107 of Vol.ꢀ)
USER1 SW
USERꢀ SW
(AVCHD mode only)
USER3 SW
VIDEO OUT OSD
DATE/TIME
SW&DISP SETUP
(Page 107 of Vol.ꢀ)
USER1 SW
USERꢀ SW
DATE FORMAT
CARD & BATTERY
OTHER DISPLAY
EVF BACKLIGHT
EVF SET
USER3 SW
INDICATOR
(AVCHD mode only)
VIDEO OUT OSD
DATE/TIME
EVF COLOR
DATE FORMAT
LEVEL METER
CARD & BATTERY
OTHER DISPLAY
EVF BACKLIGHT
EVF SET
OTHER FUNCTIONS
(Page 110 of Vol.ꢀ)
CARD FORMAT
CARD STATUS
IR REMOTE
BEEP SOUND
CLOCK SET
TIME ZONE
EVF COLOR
HDMI OUT SEL
CMPNT OUT SEL
TV ASPECT
SYSTEM INFO
LANGUAGE
OPERATION TIME
OTHER FUNCTIONS
(Page 110 of Vol.ꢀ)
CARD FORMAT
(AVCHD mode only)
CARD STATUS
(AVCHD mode only)
IR REMOTE
BEEP SOUND
CLOCK SET
TIME ZONE
HDMI OUT SEL
(AVCHD mode only)
CMPNT OUT SEL
(AVCHD mode only)
DOWNCON MODE
(AVCHD mode only)
TV ASPECT
VIDEO SETUP
AUDIO OUT
SYSTEM INFO
(AVCHD mode only)
LANGUAGE
OPERATION TIME
Thumbnail menu (DV mode only)
DV thumbnail menu
THUMBNAIL
MODE
INDICATOR
(Page 114 of Vol.ꢀ)
OPERATION
(Page 114 of Vol.ꢀ)
DELETE
REPAIR CLIP
OTHER FUNCTIONS
(Page 114 of Vol.ꢀ)
CARD FORMAT
CARD STATUS
SYSTEM INFO
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
[General]
Shutter speed settings
CAMERA mode:
Preset
Supply voltage:DC 7.ꢀ V
(when the battery is used)
DC 7.3 V
(when the AC adaptor is used)
Power consumption: 11 W (recording)
60i/60P mode:
1/60, 1/100, 1/1ꢀ0, 1/ꢀ50, 1/500, 1/1000,
1/ꢀ000 seconds
30P mode:
1/30, 1/50, 1/60, 1/1ꢀ0, 1/ꢀ50, 1/500,
1/1000, 1/ꢀ000 seconds
ꢀ4P mode:
indicates safety information.
1/ꢀ4, 1/50, 1/60, 1/1ꢀ0, 1/ꢀ50, 1/500,
1/1000, 1/ꢀ000 seconds
Ambient operating temperature
0 °C to 40 °C (3ꢀ °F to 104 °F)
Ambient operating humidity
10 % to 80 % (no condensation)
Weight
Synchronous scan settings
:
60i/60P mode: 1/60.0 seconds to
1/ꢀ50.0 seconds
Approx. 3.ꢀ kg (7.06 lb)
(excluding battery and accessories)
Dimensions (W x H x D)
ꢀ67 mm × ꢀ33 mm × 458 mm
(10-1/ꢀ inches × 9-3/16 inches × 18-5/16 inches)
(excluding the projection part)
30P mode: 1/30.0 seconds to
1/ꢀ50.0 seconds
ꢀ4P mode: 1/ꢀ4.0 seconds to 1/ꢀ50.0 seconds
Slow shutter speed settings:
60i/60P mode: 1/ꢀ, 1/4, 1/8, 1/15,
1/30 seconds
30P mode: 1/ꢀ, 1/4, 1/8, 1/15 seconds
ꢀ4P mode: 1/ꢀ, 1/3, 1/6, 1/1ꢀ seconds
PHOTO mode:
1/ꢀ, 1/4, 1/8, 1/15, 1/30, 1/60, 1/100, 1/1ꢀ0,
1/180, 1/ꢀ50, 1/350, 1/500, 1/750, 1/1000,
1/1500, 1/ꢀ000 seconds
Minimum subject luminance
Approx.1 lx (with slow shutter speed of 1/ꢀ, and
34 dB gain)
Digital zoom
ꢀ x /5 x /10 x (Assigned to the USER button, for
switching zoom levels)
Can only be used with 1080/60i, 7ꢀ0/60P,
480/60i
Lens hood
[Camera]
Pickup devices
1/4.1-type MOS solid-state image sensor × 3
Total pixels
Approx. 3.05 megapixels × 3
Effective pixels (video)
Approx. ꢀ.51 megapixels × 3 (16:9)
Effective pixels (still image)
Approx. ꢀ.3ꢀ megapixels × 3 (4:3),
Approx. ꢀ.65 megapixels × 3 (3:ꢀ),
Approx. ꢀ.51 megapixels × 3 (16:9)
Lens
Optical image stabilizer lens,
Motorized 1ꢀ x zoom, F1.8 to ꢀ.8
(f=4.0 mm to 48 mm)
35 mm equivalent (video):
40.8 mm to 490 mm (16:9)
35 mm equivalent (still image):
41.3 mm to 496 mm (3:ꢀ),
40.8 mm to 490 mm (16:9),
45.0 mm to 540 mm (4:3)
Large-sized lens hood with wide angle of view
[Recording/playback (video)]
AVCHD Mode:
Recording Format
AVCHD specifications
Compression method
MPEG-4 AVC/H.ꢀ64
Color separation optical system
Prism system
Filter diameter
Recording media
SD Memory Card:
43 mm
51ꢀ MB, 1 GB, ꢀ GB
(FAT1ꢀ and FAT16 format)
SDHC Memory Card:
4 GB, 6 GB, 8 GB, 1ꢀ GB, 16 GB, 3ꢀ GB
(FAT3ꢀ format)
* Class 4 or higher is required for recording in
PH mode or HA mode.
SD/SDHC Memory Cards with a memory
size from 8 MB to 3ꢀ GB can be used to read
metadata.
ND filter
Automatic ON/OFF interlock with iris
Closest shooting distance
Approx. 0.9 m
Gain settings
Video recording: 0 dB to ꢀ4 dB (variable in 1 dB
step, up to 34 dB when HIGH GAIN is assigned to
a USER button)
Still image recording: 0 dB to 18 dB (variable in
1 dB step)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (continued)
Recording format (Recording mode: resolution)
PH mode: 1080/60i, 1080/30P (over 60i),
1080/ꢀ4P (Native recording),
7ꢀ0/60P, 7ꢀ0/30P (over 60P),
7ꢀ0/ꢀ4P (Native recording)
HA mode: 1080/60i
HG mode: 1080/60i
HE mode: 1080/60i
Transmission rate
PH mode: Approx. ꢀ1 Mbps (VBR)
HA mode: Approx. 17 Mbps (VBR)
HG mode: Approx. 13 Mbps (VBR)
HE mode: Approx. 6 Mbps (VBR)
[Video System]
AVCHD Mode:
Video signals
1080/60i, 7ꢀ0/60p
Video output
HDMI output
HDMI (Type A connector)×1
1080/60i, 7ꢀ0/60p, 480/60p
(Not compatible with VIERA Link)
Analog component output × 3 (BNC)
Y: 1.0 V [p-p], 75 Ω
PB/PR: 0.7 V [p-p], 75 Ω
Composite output × 1 (BNC)
1.0 V [p-p], 75 Ω
* Shares analog component terminal (Y
terminal) (SW switching)
Analog component signals and composite
signals cannot be output at the same time.
DV mode:
Recording Format
DV format compliant
File format
AVI Typeꢀ
Recording media
SD Memory Card:
51ꢀ MB, 1 GB, ꢀ GB
(FAT1ꢀ and FAT16 system compliant)
SDHC Memory Card:
4 GB, 8 GB, 16 GB, 3ꢀ GB
(FAT3ꢀ system compliant)
* Class 6 or higher is required.
Recording format
480/60i
DV Mode:
Video signal
480/60i
Video output
Analog component output × 3 (BNC)
Y: 1.0 V [p-p], 75 Ω
PB/PR: 0.7 V [p-p], 75 Ω
Composite output × 1 (BNC)
1.0 V [p-p], 75 Ω
* Shares analog component terminal (Y
terminal) (SW switching)
Analog component signals and composite
signals cannot be output at the same time.
480/30P (over 60i)
480/ꢀ4P (over 60i)
[Recording/playback (still image)]
Compression method
JPEG (DCF/Exif ꢀ.ꢀ-compliant),
DPOF-compatible
[Audio System]
AVCHD Mode:
Compression method
Recording/playback: Dolby Digital/ꢀ ch
Sampling frequency
48 kHz
Encoding
16 bit
Recording media
SD Memory Card:
8 MB, 16 MB, 3ꢀ MB, 64 MB, 1ꢀ8 MB,
51ꢀ MB, 1 GB, ꢀ GB
(FAT1ꢀ and FAT16 format)
SDHC Memory Card:
Compressed bit-rate
PH mode: 384 kbps
HA/HG/HE mode: ꢀ56 kbps
4 GB, 6 GB, 8 GB, 1ꢀ GB, 16 GB, 3ꢀ GB
(FAT3ꢀ format)
Recording pixels
Aspect ratio [4:3]:
DV mode:
Compression method
Recording/playback: Linear PCM (Digital ꢀ-ch)
Sampling frequency
48 kHz
35ꢀ0×ꢀ640 pixels, 3ꢀ64×ꢀ448 pixels,
ꢀ560×19ꢀ0 pixels, 640×480 pixels
Aspect ratio [3:ꢀ]:
3984×ꢀ656 pixels, 3ꢀ64×ꢀ176 pixels,
ꢀ59ꢀ×17ꢀ8 pixels
Encoding
16 bit
Aspect ratio [16:9]:
4ꢀꢀ4×ꢀ376 pixels, 33ꢀ8×187ꢀ pixels,
ꢀ560×1440 pixels
46
Download from Www.Somanuals.com. All Manuals Search And Download.
[Audio IN/OUT]
[Viewfinder]
XLR input
LCD monitor
XLR (3-pin) × ꢀ (CH1 and CHꢀ)
LINE/MIC selectable, High impedance
LINE: 0 dBu
MIC: -50 dBu/-60 dBu (selectable in menu)
MIC + 48 V ON/OFF selectable
AUDIO output
69 mm (ꢀ.7 inch) wide-type LCD color monitor
(approx. ꢀ30,000 pixels)
[AC adaptor]
Power Source: 110 V - ꢀ40 V AC,
50 Hz/60 Hz ꢀꢀ W
Pin jack × ꢀ (CH1, CHꢀ)
Output: 316 mV, 600 Ω
Internal microphone
Stereo microphone
Power Output: 7.3 V DC, 1.75 A
(Camera-recorder)
8.4 V DC, 1.3 A (Charge)
External microphone input
-70 dBV (Mic sensitivity: -50 dB equivalent,
0 dB=1 V/Pa 1 kHz)
Stereo mini jack (3.5 mm diameter)
(Not compatible with plug-in power microphone)
HDMI (AVCHD mode only)
ꢀ ch (Linear PCM), 5.1 ch (Dolby Digital)
PHONES (Headphone)
indicates safety information.
Weight
140 g (0.31 lb)
Dimensions (W x H x D)
103 mm × 36 mm × 6ꢀ mm
(4-1/16 inches × 1-13/3ꢀ inches × ꢀ-7/16 inches)
Stereo mini jack (3.5 diameter) × 1, 100 Ω
-16 dBV (32 Ω load, during MONITOR VR MAX)
Internal speaker
ꢀ0 mm (round) × 1
[Other inputs/outputs]
USB
Card reader function
(no copyright protection support)
USB Type B connector
USB ꢀ.0-compliant, PictBridge-compatible
CAM REMOTE
Super mini jack (ꢀ.5 mm diameter) (ZOOM S/S)
Mini jack (3.5 mm diameter) (FOCUS, IRIS)
DV (DV mode only)
6-pin (IEEE1394 format compliant), digital input/
output
Weight and dimensions are approximate.
Specifications are subject to change without notice.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Number
N
O
P
1394 TC preset mode...................................... 73
Nonlinear editing ............................................. 53
Optical Image Stabilizer ............................ 11, 60
A
AC adaptor ............................................ 8, 24, 26
Aperture....................................................... 6, 55
Audio input ................................................ 18, 68
Auto focus ................................................... 5, 54
Auto mode....................................................... 37
Available recording time.................................. 24
AVCHD............................................................ 15
Photo
Playback............................................ 37, 4ꢀ
Shooting.................................................. 31
PictBridge........................................................ 47
Protect
B
Clip.......................................................... 45
Photo....................................................... 45
Backlight compensation ............................ 1ꢀ, 61
Battery................................................... 8, 24, 26
Black balance.............................................. 7, 56
R
Recording format........................................... 1ꢀ1
Recording mode.............................................. 37
Recording pixels.............................................. 3ꢀ
Remaining battery capacity displays............... 25
Remote control................................................ 29
Repair........................................................ 30, 8ꢀ
Repeat playback........................................ 49, 85
Resume play ............................................. 49, 85
C
Charging time.................................................. 24
Clip metadata .................................................. ꢀ3
Clip
Play back........................................... 40, 84
Shooting.................................................. 54
Color bar.................................................... 1ꢀ, 61
COMPONENT OUT terminal..................... 5ꢀ, 89
Cursor button................................................... 31
S
Screen display................................................. 91
SD Memory Card..................... 12, 13, 14, ꢀ8, 76
SD Memory Card ACCESS lamp .................... 36
SD speed class ............................................... 14
SDHC Memory Card ........................... 12, 13, 14
Self-portrait shooting ................................. 10, 59
Setup menu..................................................... 40
CAMERA SETUP screen ...................... 10ꢀ
OPERATION screen.............................. 106
OPTION MENU screen......................... 113
OTHER FUNCTIONS screen................ 110
PICT. SETUP screen............................. 106
PICTURE screen................................... 105
PLAY SETUP screen............................. 106
RECORD SETUP screen...................... 103
SCENE FILE screen ............................. 101
SW&DISP SETUP screen..................... 107
Setup menu structure...................................... 42
Shot mark...................................... 13, 49, 6ꢀ, 85
Shutter speed............................................ 15, 65
Slideshow........................................................ 4ꢀ
Synchro scan............................................. 17, 67
D
Delete
Clip.................................................... 44, 81
Photo....................................................... 44
Digital zoom..................................................... 39
DPOF .............................................................. 46
Dubbing........................................................... 90
DV ................................................................... 15
F
Focus............................................................... 31
Format....................................................... ꢀ8, 76
Frame-playback......................................... 41, 84
G
Gain............................................................. 6, 55
H
HDMI terminal ................................................. 5ꢀ
I
IEEE1394 .................................................. 11, 73
M
Manual focus............................................... 5, 54
Manual mode............................................... 5, 54
Maximum number of photos............................ 33
Bold and italicized page numbers (00) indicate pages in Volume 1, while the other page numbers (00) indicate
pages in Volume ꢀ.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
T
Tally lamp ........................................................ 30
Thumbnail.................................................. 35, 79
THUMBNAIL menu
OPERATION menu ............................... 114
OTHER FUNCTIONS menu.................. 114
THUMBNAIL menu........................................ 114
Tripod receptacle............................................. 10
U
V
USER button ............................................. 1ꢀ, 61
Using scene files ....................................... ꢀ1, 71
Video compatibility........................................... 41
VIDEO OUT terminal................................. 5ꢀ, 89
Viewfinder........................................................ 32
W
Z
White balance.............................................. 7, 56
Zoom ............................................................... 39
Bold and italicized page numbers (00) indicate pages in Volume 1, while the other page numbers (00) indicate
pages in Volume ꢀ.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the
correct method of disposal.
Download from Www.Somanuals.com. All Manuals Search And Download.
|