This product is eligible for the AVCCAM
3 Year Warranty Repair Program. For
details, see page 6.
Operating Instructions
Vol.1
Memory Card Camera-Recorder
AG-AC130AP
Model No.
1
Volume
Note that Operating Instructions Vol.1 describes basic operations of
the Memory Card Camera-Recorder.
For instructions on advanced operations of the Memory Card
Camera-Recorder, refer to Operating Instructions Vol.2 (pdf file)
contained in the supplied CD-ROM. (Page 10)
Before operating this product, please read the instructions carefully and save this manual for
future use.
ENGLISH
SS0412SI0 -YI
Printed in Japan
VQT4K21 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
indicates safety information.
CAUTION:
This apparatus can be operated at a voltage in the range of 110-240 V AC.
Voltages other than 120 V are not intended for U.S.A. and Canada.
Operation at a voltage other than 120 V AC may require the use of a different AC plug. Please contact either
a local or foreign Panasonic authorized service center for assistance in selecting an alternate AC plug.
FCC NOTICE (USA)
Declaration of Conformity
Model Number:
Trade Name:
AG-AC130AP
Panasonic
Responsible Party: Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094
Support contact: 1-800-524-1448
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instructions and do not make any
unauthorized modifications.
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference”
available from FCC local regional offices helpful.
FCC Warning:
To assure continued FCC emission limit compliance, follow the attached installation instructions and the user
must use only shielded interface cables when connecting to host computer or peripheral devices. Also any
unauthorized changes or modifications to this equipment could void the user's authority to operate this device.
NOTIFICATION (Canada)
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numéique de la classe B est conforme à la norme NMB-003 du Canada.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
IMPORTANT
“Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the
right of copyright owners and be contrary to copyright laws.”
A lithium ion/polymer battery that is recyclable powers the product you have purchased.
Please call 1-800-8-BATTERY for information on how to recycle this battery.
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special
handling may apply.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Brazil Only
Brasil Apenas
Manuseio de baterias usadas
„
BRASIL
Após o uso, as pilhas e /ou baterias poderão
ser entregues ao estabelecimento comercial
ou rede de assistência técnica autorizada.
Cobrir os terminais positivo (+) e negativo (-) com uma fita isolante adesiva, antes de depositar numa
caixa destinada para o recolhimento. O contato entre partes metálicas pode causar vazamentos, gerar
calor, romper a blindagem e produzir fogo.
Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria pode irritar a
garganta, danificar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir
fogo devido ao curto circuito dos terminais. Não incinere nem aqueça as baterias, elas não podem ficar
expostas a temperaturas superiores a 100°C (212°F). O gás liberado pela bateria pode irritar a garganta,
danificar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido
ao curto circuito dos terminais provocado internamente.
Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada com
bastante água. Caso haja irritação, consulte um médico.
Para remover a bateria
Bateria Principal de Energia
Bateria do Controle Remoto
Pressione o botão para liberar a bateria.
1) Empurre a trava na direção exibida pela seta
1 para remover o suporte.
Botão de liberação da
bateria
2) Remova a bateria tipo botão do suporte da
bateria.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Batteries that may be used with this product (Correct as of September 2011)
Panasonic CGA-E/625 (bundled) and VW-VBG6 (optional) batteries may be used with this product.
The CGA-E/625 (bundled) and VW-VBG6 (optional) batteries contain a function to enable verification as
to whether they may be safely used with this product.
It has been found that counterfeit battery packs which look very similar to the genuine product are
made available to purchase in some markets. Some of these battery packs are not adequately
protected with internal protection to meet the requirements of appropriate safety standards. There is
a possibility that these battery packs may lead to fire or explosion. Please be advised that we are not
liable for any accident or failure occurring as a result of use of a counterfeit battery pack. To ensure that
safe products are used we would recommend that a genuine Panasonic battery pack is used.
AC Adaptor (Battery Charger)
The rating plate is on the underside of the AC Adaptor (Battery Charger). Disconnect the AC mains plug
from the AC mains socket when not in use.
AVCCAM 3 Year Warranty Repair Program*1
Thank you for purchasing this Panasonic AVCCAM device.
Register as a user for this device to receive a special service warranty up to three years of free warranty repairs.
Customers who register as users on the website will receive an extended warranty repair valid for up to
three years.
1st year
2nd year
3rd year
2
3
4
AVCCAM device
Basic warranty
Extended warranty repair
*
*
*
*1: Please note that this extended warranty is not available in some countries/regions. *2: Not all models eligible for extended warranty coverage.
*3: The basic warranty period may vary depending on the country/region. *4: Not all repair work is covered by this extended warranty.
Free 3 years of Warranty Repairs
Make sure to save the “Registration Notice” e-mail
during the warranty period.
Purchase
AVCCAM product
Register online
within 1 month
“Registration Notice”
e-mail sent
Please note, this is a site that is not maintained by Panasonic Canada Inc. The Panasonic Canada Inc. privacy policy does not apply and is not applicable in relation to any
information submitted. This link is provided to you for convenience.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The SDHC logo and SDXC logo are trademarks of SD-3C, LLC.
“AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporation.
The “DV” is a registered trademark.
•
•
•
•
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks
of HDMI Licensing LLC.
•
•
Microsoft®, Windows®, and Windows Vista® are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Screenshots are used in accordance with Microsoft Corporation guidelines.
IBM and PC/AT are registered trademarks of International Business Machines Corporation.
Intel® is a registered trademark or a trademark of Intel Corporation in the United States and/or other
countries.
•
•
•
Apple®, Macintosh®, and Mac OS® are trademarks or registered trademarks of Apple Inc. in the United
States and/or other countries.
•
•
•
Other model names, company names, and product names listed in these operating instructions are
trademarks or registered trademarks of their respective companies.
This product is licensed under the AVC Patent Portfolio License for the personal and non-commercial
use of a consumer, and no license is granted or shall be implied for any use other than the personal uses
detailed below.
- To encode video in compliance with the AVC standard (“AVC Video”)
- To decode AVC Video that was encoded by a consumer engaged in a personal and non-commercial
activity
- To decode AVC Video that was obtained from a video provider licensed to provide AVC Video
Additional information may be obtained from MPEG LA, LLC (http://www.mpegla.com).
- Separate license contracts must be obtained from MPEG LA where SD Memory Cards containing
information recorded with this product are to be distributed to end users for commercial purposes. “End
user” refers to persons or organizations handling such contents for personal use.
How to read this document
■■
Illustrations
Illustrations of the camera, menu screens, and other items, may vary from the actual items.
In order to identify the terminals on the camera body, the supplied protective caps are not illustrated
except in “Description of parts” (Pages 19, 20).
•
•
Reference pages
Reference pages in this document are indicated by (Page 00).
•
SD/SDHC/SDXC memory cards
SD/SDHC/SDXC memory cards are all described as memory cards. Each name is described when
explained individually.
•
Notations
The menu items displayed on the screen are enclosed in square brackets like [Menu items], and
characters printed on camera and the remote control are enclosed in angle brackets as in <item name>.
•
Menu display language
[English] is set in the factory settings. You can change the display language in [LANGUAGE] item of the
[OTHER FUNCTIONS] screen.
•
7
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the camera
This camera is equipped with a 1/3, 2.2 mega pixel 3MOS sensor and an optical 22X cam-type zoom lens.
It supports simultaneous and relay recording using two memory card slots. In addition, it is a hand-held
camera-recorder that supports commercial HD mode (AVCHD)/SD mode (DV) recording.
In this document, “HD mode” is referred to as “AVCHD mode” and “SD mode” is referred to as “DV
mode”.
•
Video equipment/television/monitor
DV tape equipment/memory card
camera-recorder/computer, etc.
HDMI cable
(can only be
used in
AVCHD mode)
Data can be transferred for
backup/dubbing/editing.
Video pin cable
IEEE1394 (DV) cable
(can only be used in DV mode)
Computer
Audio pin cable
Memory card
Saves and reads the setting
values of scene files or user
files on the memory card.
AG-AC130A
AVCHD mode
Speed class 4 or higher can be used when in PH/HA
mode.
Speed class 2 or higher can be used when in PM/HE
mode.
DV mode
Speed class 6 or higher can be used.
USB2.0 connection cable
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Volume 1 (This Book)
Read this first! ................................................2
How to use the camera ..................................8
Please read before use ................................ 11
Compatible memory card for this camera..... 11
Menu
Setup menu structure ..................................32
<CAMERA> mode menu .............................. 32
Playback <PB> mode menu ......................... 34
(SD speed class 4)....................... 12
(SD speed class 6)....................... 12
Operating precautions.................................13
Reference
Specifications...............................................35
Before use
Before using the camera..............................15
Accessories ..................................................17
Optional accessories ...................................17
Description of parts
Description of parts......................................18
Left side ........................................................ 18
Top and right side ......................................... 19
Front side and rear side................................ 20
Remote control ............................................. 21
Preparation
Recharging the battery ................................21
Recharging ................................................... 21
Power sources..............................................23
Using the battery........................................... 23
Using the AC adaptor.................................... 24
Adjusting the hand strap .............................24
Attaching the shoulder strap.......................25
Attaching/removing the lens hood .............25
Attaching/removing the lens cap................25
Fitting the eye cup........................................26
The remote control.......................................26
Inserting the battery...................................... 26
Remote control usable range........................ 26
Turning the camera ON/OFF........................27
Switching to AVCHD mode/DV mode ........... 27
Setup menu basic operations .....................28
Using the setup menu................................... 28
Initializing the setup menu ............................ 29
Setting the calendar.....................................30
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume 2 (CD)
Shooting
Editing
Using the viewfinder
Tally lamp
Connecting external devices
Nonlinear editing
Basic shooting operations
Using the zoom function
How to handle data recorded on the
memory card
Shooting in manual mode
Shooting in 1080i/480i progressive mode
Using convenient shooting functions
Using special functions for recording
Adjusting the shutter speed
Changing audio input
Dubbing
Displays
Screen displays
Using shooting settings (scene files)
Storing scene files and other settings on
memory cards
Clip metadata (AVCHD mode only)
Using the counter
Menu
Setup menu list
Charging the built-in battery/setting the
time code
Reference
Before calling for service
Updating the firmware incorporated into
the unit
Playback
Basic playback operations
Thumbnail screen
Playback settings [PLAY SETUP]
Thumbnail operations
Useful playback functions
Cleaning
Storage precautions
Recording format list
Index
How to open the operating instruction manual PDF files
„
Discontinue installation if the installation screen of the software opens as a result of inserting the CD-ROM.
When [INDEX.pdf] on the CD-ROM is opened, a list of the operating instruction manuals will be displayed.
Click on the document name of the manual to be opened.
Adobe® Reader® is required to read PDF files.
„
It can be downloaded from the home page of Adobe Systems.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Please read before use
Compatible memory card for this camera
Shooting in AVCHD mode
„
Speed class 4 or above is required for recording in PH mode/HA mode. Speed class 2 or above is required
for recording in PM mode/HE mode. It is recommended that you use the following Panasonic memory
cards. (As of September, 2011)
Shooting in DV mode
„
Speed class 6 or above memory cards are required. It is recommended that you use the following
Panasonic memory cards. (As of September, 2011)
Saving/reading user
Memory card
type
Storage
capacity
AVCHD
shooting/playback
DV
files and scene files
and reading metadata
(AVCHD only)
shooting/playback
8 MB
16 MB
Cannot be used.
Successful operation is
not guaranteed.
Shooting may suddenly
stop with certain SD
memory cards.
32 MB
64 MB
128 MB
256 MB
Cannot be used.
Can be used.
SD memory card
512 MB
1 GB
2 GB
Can be used.
4 GB
Can be used.
6 GB
—
Can be used.
—
8 GB
Can be used.
SDHC memory
card
12 GB
16 GB
32 GB
48 GB
64 GB
Can be used.
SDXC memory
card
—: No available Panasonic memory cards
Please see our support page at the following website for the latest information not included in these
operating instructions.
•
This camera supports FAT12 and FAT16 formatted SD memory cards, FAT32 formatted SDHC memory
cards, and exFAT formatted SDXC memory cards that are compliant with the SD standard.
SDHC memory cards of 4 GB or above that do not have the SDHC logo and SDXC memory cards of 48
GB or above that do not have the SDXC logo are not compliant with the SD standard.
Use this camera to format memory cards. Formatting memory cards on computers or other devices may
cause recording to take longer than normal, or may cause memory cards to become incompatible with
this product. (Page 13 of Vol.2) (Use this camera to reformat any memory cards that have been formatted
on computers or other devices.)
•
•
•
Multimedia cards cannot be used.
•
11
Download from Www.Somanuals.com. All Manuals Search And Download.
(SD speed class 4)
This refers to a class 4 speed standard (SD speed class) for the continuous writing of data between SD
compatible devices and memory cards as designated by the SD standard.
When the use of an SD speed class 4 memory card is recommended for SD-compatible products, this
indicates that stable recording operation can be achieved by using memory cards of class 4 and above.
(SD speed class 6)
This refers to a class 6 speed standard (SD speed class) for the continuous writing of data between SD
compatible devices and memory cards as designated by the SD standard.
When the use of an SD speed class 6 memory card is recommended for SD-compatible products, this
indicates that stable recording operation can be achieved by using memory cards of class 6 and above.
I
UHS- compatibility
I
I
I
UHS- (Ultra High Speed ) is speed standard for SD memory card. You can use a UHS- memory
•
card, which performs as an SD speed class 10 memory card on this camera.
Reminders for handling
Do not allow dirt, water, or other substances to come into contact with the terminal on the back of the
memory card.
•
Do not leave the memory card in the following places:
•
- Direct sunlight or places of high temperature, such as near heating equipment
- Humid and dusty locations
- Locations with high variations in temperature (where condensation occurs)
- Locations that are subject to static electricity and electromagnetic waves
Store memory cards in bags or cases after use.
•
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating precautions
When using the camera in the rain, snow, or at
the beach, do not allow water to get into it.
AC adaptor (battery charger) and battery
• If the <CHARGE> lamp continues to flash even
when the battery temperature is normal, the
battery or AC adaptor (battery charger) might be
damaged. Contact your dealer.
Doing so will cause damage to the camera and
the memory card. (This may result in irreparable
damage.)
•
The battery takes longer to charge when it is
warm.
Using the AC adaptor (battery charger) near
radios may distort their sound. Keep the AC
adaptor (battery charger) 1 meter or more away
from radios.
•
Keep the camera away from devices (such
as TV sets and video game machines) that
generate magnetic fields.
•
Using the camera on top of or near a television
set may cause distortions in the image or sound
due to the electromagnetic waves that the
television emits.
•
The AC adaptor (battery charger) may make
some noise when in use, but this is normal.
•
The powerful magnetic fields generated by
speakers or large motors may damage recorded
content or distort images.
•
•
•
Be careful not to drop the camera when
carrying it around.
• Strong impacts may damage the camera unit and
cause it to stop working properly.
• Handle the camera with care using the hand
strap or shoulder strap to carry it.
The electromagnetic waves emitted from a
microcomputer may adversely affect the camera
and cause images or sound to be distorted.
If the camera is adversely affected by devices
that generate magnetic fields and it no longer
operates properly, turn it off and remove the
battery or unplug the AC adaptor from the power
outlet. Then install the battery again or reconnect
the AC adaptor. After this, turn the camera back
on.
Do not spray the camera with insecticides or
other volatile substances.
Spraying the camera with insecticides or other
volatile substances may deform it or cause the
coating to peel off.
•
Do not leave the camera in contact with rubber or
PVC products for extended periods of time.
•
Do not use the camera near radio transmitters
or high-voltage equipment.
After use, remove the battery or disconnect the
AC power supply cord from the power outlet.
Using the camera near radio transmitters or high-
voltage equipment may adversely affect the
recorded images or sound.
•
Battery characteristics
This camera uses a rechargeable lithium ion
battery. It generates electrical energy through
an internal chemical reaction. This reaction is
easily influenced by the ambient temperature
and humidity, and the effective operating time of
the battery is reduced as the temperature rises
or falls. If you use this camera at locations with
extremely low temperatures, its operating time will
be reduced.
Do not allow sand or dust to get into the
camera when using it at the beach or other
similar places.
Sand and dust can damage the camera or
memory card. (Be careful when inserting or
removing a memory card.)
•
If the battery becomes extremely hot, a protective
function will engage and you will not be able to use
it for a while.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure to remove the battery after use.
Completely remove the battery from the camera.
(Even if you turn the camera off, leaving the
battery attached still consumes a small amount of
electricity.) The battery will over-discharge if you
leave it in the camera for long periods of time and
may become impossible to recharge.
Do not remove the battery when the POWER
switch is ON.
Turn the POWER switch OFF and make sure that
the mode lamp is completely off before removing
the battery.
Liquid crystal displays
• Images or characters can linger on the screen of
the LCD or viewfinder if they are left displayed
for a long time, but you can fix this by leaving the
camera off for several hours.
• The LCD monitor is managed with high precision
to ensure that 99.99% of the pixels are effective
leaving only 0.01% of pixels that are either dead
or remain on all the time. This is normal and will
have no effect on recorded images.
• Dew may form on the LCD monitor if you use
the camera in locations of intensely varying
temperatures. Wipe it dry with a soft, dry cloth.
Protect the battery terminals.
Do not allow dust or foreign substances to cling to
the battery terminals.
If you accidentally drop the battery, check the body
and terminals if they have been deformed.
Inserting a deformed battery into the camera or
the AC adaptor (battery charger) may damage the
camera or the AC adaptor (battery charger).
The LCD monitor may appear a little dimmer right
after turning on a cold camera. The brightness will
go back to normal when the internal temperature
increases.
•
Do not point the eyepiece of the lens or
viewfinder at the sun.
Doing so may damage the internal parts.
Reminders when discarding memory cards or
transferring them to others
Protective caps for the terminals
Keep protective caps fitted over connecting
terminals that are not being used.
Formatting memory cards or deleting data using
the functions of this camera or a computer will
merely change the file management information
and will not completely erase the data stored
in the memory cards. It is recommended that
you physically destroy memory cards when
discarding them, or use data deletion software for
commercially available for computers to completely
erase the data when transferring them to others.
Users are responsible for managing the data stored
in their memory cards.
Mosaic-like noise may appear on the playback
images in the following shooting conditions.
When there is a complex pattern in the
background
When moving the camera a long distance or
moving quickly
When the subject is moving quickly
(Especially when shooting in HE mode)
•
•
•
Depending on the signal reading system of the
pickup devices (MOS sensor), the following
problems may occur.
A subject that quickly crosses the screen may
appear distorted in some shooting conditions.
When a subject is lit by the flash, the screen may
appear split horizontally.
•
•
(The possibility of the occurrence may be
reduced by setting the shutter speed lower.)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Before using the camera
Always take trial shots
When shooting important events (such as weddings), make sure to take trial shots to confirm that sound
and image are being properly recorded before actual shooting.
•
Be sure to check and set the calendar and time zone
These settings affect the control and playback sequence of recorded contents. Check and set the
calendar and time zone before shooting. (Page 30)
•
There are no guarantees for recorded content
In the unlikely event that content that was not recorded due to a malfunction in the camera or the memory
card in use, please understand that no compensation can be provided.
•
Copyrights
Copyright laws forbid the use of video and audio material that you recorded for any purpose other than
your own personal enjoyment.
•
Caution regarding laser beams
The lens may suffer damage if struck by a laser beam. Make sure that laser beams do not strike the lens
when shooting in an environment where laser devices are used.
•
Media that can be used with this camera
SD/SDHC/SDXC memory cards can be used. See page 11 for details.
•
Attaching the camera to a tripod
The tripod hole supports 1/4-20UNC and 3/8-16UNC screws. Use it according to the fixing screw
•
diameter of the tripod.
The depth of the tripod hole is 5.5 mm. Do not tighten the tripod screw excessively when attaching this
camera to a tripod.
•
Attach the tripod to the tripod hole on the bottom side.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
What is AVCHD?
AVCHD is a standard for recording and playback of high definition video.
■
Video is compressed in the MPEG-4 AVC/H.264 format, and audio is recorded in Dolby Digital.
What is DV?
■
DV is a format that adopts the AVI Type2 file format that can record and play back video in DV mode.
It records audio in linear PCM format.
Regarding SDHC/SDXC memory card and recorded video compatibility, take note
of the following:
SDHC/SDXC memory cards
SDHC/SDXC memory cards cannot be used with non-SDHC/SDXC-
compatible equipment.
•
•
When using another device, ensure that it supports SDHC/SDXC memory
cards.
Compatibility of video recorded in AVCHD mode
Recorded video cannot be used with non-AVCHD-compatible equipment.
•
•
Playback may not always be possible on all AVCHD-compatible equipment. In such instances, play your
video using this camera.
Compatibility of video recorded in DV mode
When playing back memory cards recorded using the DV mode of the camera in Panasonic AG-HMC80
series
•
•
- [ ] is displayed on the clip on the thumbnail screen.
?
- The playback will be images only. Audio is not played back.
- You cannot delete or repair a recorded clip, or add or remove a shot mark.
When playing back a memory card recorded using a camera in Panasonic AG-HMC80 series on this
camera
- [ ] is displayed on the clip on the thumbnail screen.
?
- Both image and audio can be played back.
- You cannot delete or repair a recorded clip, or add or remove a shot mark.
For details about clips, see “Thumbnail screen” (Page 51 of Vol.2).
•
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Eye cup (Page 26)
Shoulder strap (Page 25)
AC adaptor (Battery charger)/
DC cord
Battery*
AC power supply cables
Wireless remote control and Microphone holder
coin battery (CR2025) (Page 63 of Vol.2)
(Page 26)
Microphone holder screws
(Page 63 of Vol.2)
Length 6 mm (2 pieces)
Length 12 mm (2 pieces)
Microphone holder adaptor
(Page 63 of Vol.2)
CD-ROM
- Operating Instructions (PDF)
- AVCCAM Restorer Software
- AVCCAM SD Card File
Recovery Software
The following accessories are attached to the unit.
Lens cap (Page 25)
INPUT terminal cap
(2 pieces)
Lens hood (Page 25)
Hand strap (Page 24)
* The battery provided with this product is CGA-E/625. If you need an additional battery, see the following optional
accessories list.
Consult your dealer when purchasing additional accessories.
Adequately process the AC cord cap and the packaging material after taking out the product.
•
•
Optional accessories
XLR microphone
•
AG-MC200G
Battery
•
VW-VBG6 (7.2 V, 5800/5400 (typ./min.) mAh)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of parts
Description of parts
Left side
1
2
3
4
5
8 9 10
6
7
16
11
17
18
19
20
33 34
35
12
13
14
15
BARS
AUDIO
CH1 SELECTCH2 SELECT
36
37
38
INT(L)
INT(R)
INPUT1
INPUT2
EVF DTL ZEBRA
INPUT2
LCD
WFM
CH1
CH2
AUTO
MANU
AUTO
MANU
21 22 23
24 26 27
25
29 31 32
28 30
COUNTER-RESET/TC SET
39
40
1
2
Built-in microphone (Page 37 of Vol.2)
22 Zoom ring (Page 17 of Vol.2)
If you do not need the zoom ring pin, attach it to
the zoom ring pin hole (Page 19) to prevent the loss.
INPUT1 switch (MIC POWER + 48V) (Page 38
of Vol.2)
23 IRIS ring (Page 19 of Vol.2)
3
INPUT2 switch (MIC POWER + 48V) (Page 38
of Vol.2)
24 IRIS button (Page 19 of Vol.2)
4
5
6
7
8
9
HANDLE ZOOM switch (Page 17 of Vol.2)
Diopter adjustment dial (Page 5 of Vol.2)
INPUT1 LINE/MIC switch (Page 38 of Vol.2)
INPUT2 LINE/MIC switch (Page 38 of Vol.2)
OIS button (Page 27 of Vol.2)
25 GAIN switch (Page 20 of Vol.2)
26 WHITE BAL switch (Page 20 of Vol.2)
27 FUNCTION knob (Page 26 of Vol.2)
28 SHTR dial (Page 34 of Vol.2)
29 DIAL SEL button (Page 34 of Vol.2)
30 DISP/MODE CHK button (Page 25 of Vol.2)
31 AUTO/MANU switch (Page 18 of Vol.2)
LCD monitor (Page 6 of Vol.2)
10 USER button (Page 27 of Vol.2)
11 ND FILTER dial (Page 20 of Vol.2)
12 FOCUS ASSIST button (Page 19 of Vol.2)
13 FOCUS switch (Page 18 of Vol.2)
14 PUSH AUTO button (Page 18 of Vol.2)
15 ZOOM switch (Page 17 of Vol.2)
16 SCENE FILE dial (Page 40 of Vol.2)
17 MENU button (Page 28)
32 AUDIO LEVEL knob (CH1, CH2) (Page 39 of
Vol.2)
33 ZEBRA button (Page 25 of Vol.2)
34 WFM button (Page 28 of Vol.2)
35 AUDIO CH1/CH2 SELECT switch (Page 37 of
Vol.2)
36 BARS button (Page 28 of Vol.2)
37 EVF DTL button (Page 6 of Vol.2)
38 LCD button (Page 8 of Vol.2)
18 EXEC button (Page 57 of Vol.2)
19 OPERATION lever (Page 28)
39 COUNTER-RESET/TC SET button (Page 46 of
Vol.2)
20 AUDIO MON/ADV button (Page 29 of Vol.2)
21 Focus ring (Page 18 of Vol.2)
40 AUDIO AUTO/MANU CH1/CH2 switch (Page 39
of Vol.2)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Top and right side
7
8
9
1
2
3
14 15 16
4
5
6
10111213
1
2
VIDEO OUT (TC PRESET IN/OUT) terminal
(Page 66 of Vol.2)
AUDIO OUT CH1/CH2 terminal (Page 66 of
Vol.2)
3
4
5
6
7
Mode lamp (Page 27)
POWER/MODE switch (Page 27)
Lock release button (Page 27)
START/STOP button (Page 11 of Vol.2)
Protective caps
Keep protective caps fitted over connecting
terminals that are not being used.
8
9
Shoulder strap mounting location (Page 25)
Zoom lever (handle side) (Page 17 of Vol.2)
10 REC CHECK button (Page 12 of Vol.2)
11 Zoom lever (Page 17 of Vol.2)
12 AUDIO INPUT1/2 terminal (XLR 3-pin) (Page 38
of Vol.2)
13 Zoom ring pin hole
14 HOLD switch (Page 24 of Vol.2)
15 START/STOP button (handle side) (Page 24 of
Vol.2)
16 Accessory shoe
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Front side and rear side
1 2
7
3
4
8
9
17
18
12
13
19
20
10
11
14 15 16
21 22
5
6
1
2
3
4
5
6
7
8
Remote control sensor (front) (Page 26)
Natural light sensor (Page 22 of Vol.2)
Tally lamp (front) (Page 9 of Vol.2)
Built-in speaker (Page 62 of Vol.2)
AWB button (Page 20 of Vol.2)
20 CAM REMOTE jack*
FOCUS/IRIS (3.5 mm mini jack)
You can connect a remote control unit (optional)
to control the FOCUS and IRIS operations.
ZOOM S/S (2.5 mm super mini jack)
You can connect a remote control unit to control
the zoom and recording start/stop operation.
* Do not connect any equipment except the remote
control to the <CAM REMOTE> jack. Connecting
any equipment other than the remote control may
cause the image brightness to change or the images
to appear out of focus.
Tripod hole (bottom) (Page 15)
Viewfinder (Page 5 of Vol.2)
Memory card slot cover and OPEN lever
(Page 10 of Vol.2)
9
Memory card slot and memory card access
lamp (Page 12 of Vol.2)
21 HDMI OUT terminal (Page 66 of Vol.2)
22 DV OUT terminal (Page 65 of Vol.2)
10 Tally lamp (rear) (Page 9 of Vol.2)
11 Remote control sensor (rear) (Page 26)
12 Battery release button (Page 23)
13 Battery compartment (Page 23)
14 HD indicator (Page 27)
15 SLOT SEL button (Page 12 of Vol.2)
16 Protective caps
Keep protective caps fitted over connecting
terminals that are not being used.
17 USB2.0 terminal (Page 64 of Vol.2)
18 Headphone jack (3.5 mm stereo mini jack)
(Page 63 of Vol.2)
19 INDEX REMOTE jack (2.5 mm super mini
jack)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
When using the remote control, set the [IR REMOTE] on the [OTHER FUNCTIONS] menu to [ON]. The
factory setting is set to [OFF]. (Page 93 of Vol.2)
1
EXT DISPLAY button
(Page 62 of Vol.2)
Take note that the following buttons are for
functions that cannot be executed on this
camera.
2
3
DATE/TIME button (Page 62 of Vol.2)
START/STOP button
Same function as the <START/STOP> button
on the camera.
button
•
•
PHOTO SHOT button
4
ZOOM/VOL button
(Page 62 of Vol.2)
START/
STOP
PHOTO
SHOT
EXT
DISPLAY
3
4
1
2
DATE/
TIME
ZOOM
5
6
PLAY button (Page 50 of Vol.2)
VOL
SEARCH button (Page 50 of Vol.2, Page 61 of
Vol.2)
5
7
9
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
6
8
10
6
8
10
12
7
8
9
PAUSE button (Page 50 of Vol.2)
STILL ADV button (Page 62 of Vol.2)
STOP button (Page 50 of Vol.2)
MENU
ENTER
11
10 SKIP button (Page 50 of Vol.2, Page 61 of Vol.2)
11 OPERATION buttons
Same function as the OPERATION lever on the
camera.
12 MENU button
Same function as the MENU button on the
camera.
Remote control usable range (Page 26)
Preparation
Recharging the battery
Recharging
The battery is not charged at the time of purchase. Charge the battery before use.
It is recommended that you keep one extra battery as a spare.
Connect the power cord to the AC adaptor.
Insert the battery.
1
2
Disconnect the DC cord. The battery cannot
be charged if the DC cord is connected.
•
Charging lamp <CHARGE>
DC cord
Align the battery with the mark
and insert fully.
Insert until fully in place.
(1)
(2)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Charging lamp
Remaining battery capacity display
„
„
ON: Charging
OFF: Charging complete
Flashing: See below
When using Panasonic batteries that are
compatible with this product, the remaining battery
capacity is displayed in minutes.
[
] 1h30m
If the charging lamp is flashing
„
The time remaining (as shown previously) is
displayed after a brief pause.
Confirm that there is no dirt, dust, or foreign
substances attached to the connectors of the
battery or the AC adaptor and ensure that the
adaptor has been connected correctly.
If there is dirt, dust, or foreign substances on the
connectors, disconnect the power plug from the
socket before cleaning.
If the charging lamp continues to flash, the
battery or the AC adaptor may be damaged.
Consult the dealer where it was purchased.
As battery capacity decreases, the display will
•
•
change as follows:
][ ]. When there are only 3 minutes
or less of capacity left, [ ] will be displayed
in red, and when the battery becomes empty,
] will flash.
The remaining battery capacity may not be
displayed correctly when the battery is used in
high or low temperatures, or when the battery
has not been used for a long period of time. To
ensure that the remaining battery capacity is
displayed correctly, use the battery completely
from a fully-charged state and charge it again.
(Remaining battery capacity may still not be
displayed correctly if the battery has been used
for long periods in high or low temperatures,
or if the battery has already been recharged
numerous times.)
This only serves as a guide as remaining battery
capacity display times may vary according to
usage conditions.
The remaining battery capacity display will
momentarily disappear when switching between
modes, when conducting REC CHECK
operations, or when changing the LCD brightness
since the capacity is recalculated during these
times.
[
][
][
]
[
•
[
•
Charging time and available recording time
„
standards
Maximum
Battery
model
Voltage/
capacity
Charging continuous
time
recording
time
7.2 V/
Approx. 5
hours and
50 minutes 30 minutes
Approx. 3
hours and
CGA-E/625 5800/5400
•
•
(bundled)
(typ./min.)
mAh
7.2 V/
Approx. 5
hours and
50 minutes 30 minutes
Approx. 3
hours and
VW-VBG6 5800/5400
(optional)
(typ./min.)
mAh
The figures in the preceding table are for normal
temperature conditions (temperature 25°C (77°F)/
humidity 60%). This only serves as a guide
since charging may take longer in high or low
temperatures.
•
This is not displayed when using the AC adaptor.
•
The battery and the camera itself becomes hot
while it is being used or charged.
Available recording time is reduced if you
repeatedly start and stop recording.
The battery takes longer to charge when it is
warm.
Using the AC adaptor near radios may distort
their sound. Keep the AC adaptor 1 meter or
more away from radios.
The AC adaptor may make some noise when
in use, but this is normal.
•
•
•
•
Charging may take longer if the battery has not
been in use for a long period of time.
•
•
Given here are the standard maximum
continuous recording times when recording in
PH 1080/60i mode using the viewfinder with no
connections to any external devices and with the
LCD monitor closed.
This serves only as a guide as available recording
times may vary according to usage conditions.
Charging times are based on the time to charge
batteries from an empty state.
•
•
•
•
The battery cannot be recharged when a DC
cord is connected to the AC adaptor.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Power sources
Using the battery
Installation
Removal
Insert the battery until it clicks into place.
Turn the POWER/MODE switch <OFF> (Page 27),
and confirm that the mode lamp is off.
1
1
2
Remove the battery while pressing the
battery release button.
Support the battery with your hand to ensure
that it will not fall.
Battery release
button
Mode lamp
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the AC adaptor
Installation
Removal
Connect the DC cord to the AC adaptor.
Turn the POWER/MODE switch <OFF> (Page 27),
and confirm that the mode lamp is off.
1
2
3
1
2
3
Plug the AC cord into the power outlet.
Remove the DC cord’s battery connector
while pressing the battery release button.
Insert the DC cord’s battery connector until
it clicks into place.
Disconnect the AC cord from the power
outlet.
DC cord’s battery connector
The battery cannot be recharged when a DC
cord is connected to the AC adaptor.
Disconnect the AC cord from the power outlet
when this device is not in use.
•
•
CAUTION:
• This apparatus can be operated at a volt-
age in the range of 110 – 240 V AC.
Voltages other than 120 V are not intended
for U.S.A. and Canada.
Operation at a voltage other than 120 V AC
may require the use of a different AC plug.
Please contact either a local or foreign
Panasonic authorized service center for as-
sistance in selecting an alternate AC plug.
Adjusting the hand strap
Adjust the hand strap to suit your hand.
Open the cover and adjust the length of the
strap.
1
Close the cover.
2
Make sure that the cover is firmly closed.
•
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the shoulder strap
It is recommended that you attach the shoulder strap to avoid dropping the camera.
20 mm or longer
20 mm or longer
Attaching/removing the lens hood
Removing the lens hood
Attaching the lens hood
Turn the lens hood counterclockwise to remove
it.
Attach the lens hood to the camera with the lens
hood guide facing up and aligned to the center of
the camera.
•
•
Turn the lens hood clockwise until it clicks and
locks into place.
•
Center of the camera
The side with lens
hood guide
(2)
(1)
Attaching/removing the lens cap
Removing the lens cap
Pinch the lens cap to remove it.
•
Attaching the lens cap
Pinch the lens cap to attach it.
Keep the lens cap attached when the camera is
not in use to protect the lens.
•
•
Lens cap
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting the eye cup
Attach the eye cup by fitting the eye cup holder and
the ridges of the eye cup together.
Eye cup holder
Eye cup
Turning the eye cup after attaching it may
cause the eye cup holder to come off. If the eye
cup holder does come off, see “Cleaning the
viewfinder” (Page 102 of Vol.2) and refit it.
•
Ridges
The remote control
Inserting the battery
Remote control usable range
For the remote control sensor,
Distance: Approx. within 5 m
Angle: Approx. 10° upward, 15° downward, and
15° sideways
Remove the holder while pushing the catch
in the direction shown by arrow (1).
1
(using the accessory battery)
(2)
(1)
Remote control
sensor (rear)
Insert the battery with the side marked with
<+> facing up.
2
Remote control
sensor (front)
Return the holder to its original position.
3
When the battery (CR2025) runs out, replace
it with a new one. (Battery life depends on the
frequency of usage but is approximated at about
one year.)
If the remote control unit fails to work even when
it is operated near the camera’s remote control
sensor, it means that the battery has run out.
Keep the battery out of the reach of children.
•
•
These are the operation range values when the
remote control is used indoors. If used outdoors
or if strong light is hitting the remote control
sensor, the remote control may not operate
properly even within the said ranges.
The remote control is set to [OFF] in the factory
settings. When using the remote control, set the
[IR REMOTE] on the [OTHER FUNCTIONS]
menu to [ON]. (Page 93 of Vol.2)
•
•
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the camera ON/OFF
Turning on the power:
Turn the POWER/MODE switch up to the <ON>
position while pressing the lock release button.
The mode lamp <CAMERA> lights up in red and
the camera goes to recording standby status
(<CAMERA> mode).
If the POWER/MODE switch is turned up to the
<MODE> position, the mode lamp <PB> will light
up in green and the camera goes to <PB> mode.
(Page 50 of Vol.2)
•
Every time the switch is turned to the <MODE>
position, the mode will change between
<CAMERA> mode and <PB> mode.
•
Mode lamp
POWER/MODE switch
Turning off the power:
Turn the POWER/MODE switch up to the <OFF>
position while pressing the lock release button.
The mode lamp <CAMERA>/<PB> goes off.
Lock release button
Switching to AVCHD mode/DV mode
Turn the camera’s POWER/MODE switch <ON>. (Page 27)
1
2
3
Press the <MENU> button.
Set [AVCHD] or [DV] from the [HD/SD MODE] items in the setup menu
[RECORDING SETUP] screen.
When the [TURN POWER OFF] message is displayed, turn the power
OFF and then ON again.
When the power is turned on again, the mode changes.
4
<HD> indicator
For instructions on how to turn the camera ON/OFF, refer to page 27.
When you switch to AVCHD mode, <HD> indicator will light up in blue.
When you switch to DV mode, <HD> indicator will turn off.
•
•
•
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menu basic operations
You can change camera settings using the setup
menu according to the shooting scene and
recording details.
Tilt the OPERATION lever in the < ><
directions to move the yellow cursor to the
function you wish to set.
>
2
3
Press the OPERATION lever (or tilt it in the
<MENU> button
<
> direction) to display the setting items.
Example:
OPERATION
lever
Tilt the OPERATION lever in the < ><
directions to move to the function you wish
to set.
Example:
>
4
5
Using the setup menu
The menu items displayed in gray characters
cannot be changed.
•
Press the <MENU> button when the camera
is not shooting or playing back video.
The following menu screens are displayed on
the viewfinder and LCD monitor.
1
Press the OPERATION lever (or tilt it in the
<
> direction) to make the setting.
When changing values or other parameters, tilt
the OPERATION lever in the < >< > directions
to change the setting value. Select the item you
wish to set, and then press the OPERATION
lever to confirm.
<CAMERA> mode (Example)
Example:
<PB> mode (Example)
Tilt the OPERATION lever in the < > direction
to return to the previous menu.
•
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat steps 4 to 5 to change other items.
6
7
Press the <MENU> button to complete settings
and return to the normal screen.
In some menus, tilting the OPERATION
lever in the < > direction or pushing the
OPERATION lever changes the setting value
and returns the previous menu.
•
Repeat steps 2 to 5 to change other
functions.
Press the <MENU> button to complete settings
and return to the normal screen.
Initializing the setup menu
The setup menu is divided into user files and scene
files and you can initialize each one to its factory
settings.
To initialize user files (all items other than
scene files)
By selecting [INIT] in the [LOAD/SAVE/INIT] item
of the [USER FILE] screen, you can restore the
current user file menu setting to its factory setting.
To initialize scene files
Among the six scene files, select the file you wish
to initialize using the <SCENE FILE> dial. Then
by selecting [INIT] in the [LOAD/SAVE/INIT] item
of the [SCENE FILE] screen, you can restore the
setting value of only the selected scene file to its
factory setting.
To initialize user files and scene files at the
same time, restore a user file and all six scene
files to their factory settings by selecting
[YES] in the [MENU INIT] item of the [OTHER
FUNCTIONS] screen.
•
Time code/[OPERATION TIME] item/[CLOCK
SET] item/[TIME ZONE] item setting values
are not initialized.
•
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the calendar
The [CLOCK SET] value is recorded in the
contents (clip) and affects the playback sequence
of the thumbnails. Before shooting, be sure to
check/set the [TIME ZONE] and [CLOCK SET].
This section will explain the steps on how to set the
calendar to September 22, 2011, 17:20.
Tilt the OPERATION lever in the <
>
5
direction and select [YES] in the [CLOCK
SET] item on the setup menu [OTHER
FUNCTIONS] screen.
Turn the camera’s POWER/MODE switch
<ON>. (Page 27)
1
Press the <MENU> button.
2
Menu operation (Page 28)
•
•
Operations can also be performed using
buttons on the remote control that correspond
to those on the camera. For details, see
Tilt the OPERATION lever in the < ><
directions to set to [2011].
>
6
7
“
Remote control” (Page 21).
Select the [TIME ZONE] item on the setup
menu [OTHER FUNCTIONS] screen and
press the OPERATION lever (or tilt it to the
3
4
<
> direction).
Tilt the OPERATION lever in the <
>
direction to change to the next item, then tilt
the lever in the < >< > directions to set to
[SEP].
Since pressing the OPERATION lever
will display the settings screen, tilt the
OPERATION lever in the < >< > directions
to set the time difference from Greenwich
Mean Time, then press the OPERATION
lever again.
Factory default setting is [0:00].
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat steps 6 and 7 to set the remaining
items.
8
The date can be set to any date between
January 1, 2000 and December 31, 2039.
For any date after December 31, 2039, [--] will
appear on the display.
•
•
•
Time is displayed in the 24-hour format.
When settings are complete, press the
OPERATION lever.
9
The time can be inaccurate so confirm that the
time is correct before shooting.
•
•
When using the camera overseas, do not set
the [CLOCK SET] to the local time but instead
enter the time difference from Greenwich
Mean Time according to the [TIME ZONE].
(Page 94 of Vol.2)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Setup menu structure
<CAMERA> mode menu
CAMERA MENU
SCENE FILE
LOAD/SAVE/INIT
SYNC SCAN TYPE
SYNCHRO SCAN
DETAIL LEVEL
V DETAIL LEVEL
DETAIL CORING
CHROMA LEVEL
CHROMA PHASE
COLOR TEMP Ach
COLOR TEMP Bch
MASTER PED
A.IRIS LEVEL
DRS
(Page 79 of Vol.2)
SW MODE
(Page 82 of Vol.2)
FUNCTION KNOB
LOW GAIN
MID GAIN
HIGH GAIN
SUPER GAIN
ATW
MF ASSIST
FOCUS ASSIST
HANDLE ZOOM
USER1
USER2
DRS EFFECT
USER3
GAMMA
WFM
KNEE
LCD
MATRIX
FACE FRAMING
SKIN TONE DTL
CARD READ
CARD WRITE
NAME EDIT
AUTO SW
(Page 84 of Vol.2)
A.IRIS
AGC
ATW
AF
RECORDING SETUP
(Page 85 of Vol.2)
HD/SD MODE
REC FORMAT
ASPECT CONV*1
PREREC MODE
SIMUL REC
TC/UB SETUP
(Page 87 of Vol.2)
TC MODE
TCG
TC PRESET
UB MODE*1
UB PRESET
EXT TC LINK
RELAY REC
INTERVAL REC*2
TIME STAMP
AUDIO LIMITER CH1
AUDIO LIMITER CH2
MIC GAIN1
MIC GAIN2
AV OUT SETUP
(Page 88 of Vol.2)
HDMI OUT SEL*2
DOWNCON MODE
HP MODE
*2
TEST TONE
VIDEO SETUP
AUDIO OUT
*1 Only in DV mode.
*2 Only in AVCHD mode.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY SETUP
(Page 89 of Vol.2)
ZEBRA DETECT1
ZEBRA DETECT2
Y GET MARKER
SAFETY ZONE*3
CENTER MARKER
FOCUS BAR
CARD FUNCTIONS
(Page 92 of Vol.2)
CARD FORMAT
CARD STATUS
IRIS METER
REC COUNTER
VIDEO OUT OSD
DATE/TIME
USER FILE
CARD READ
(Page 92 of Vol.2)
CARD WRITE
LOAD/SAVE/INIT
DATE FORMAT
LEVEL METER
ZOOM&FOCUS
CARD&BATTERY
OTHER DISPLAY
LCD SET
META DATA*2
CARD READ
EVF SET
(Page 93 of Vol.2)
RECORD
LCD BACKLIGHT
SELF SHOOT
EVF MODE
USER CLIP NAME
META DATA PROP
CLIP COUNTER RST
META INIT SET
EVF COLOR
OTHER FUNCTIONS
(Page 93 of Vol.2)
IR REMOTE
DV CONTROL*1
DV CMD SEL*1
TALLY LAMP
CLOCK SET
OPTION MENU*1*4
(Page 95 of Vol.2)
1394 STATUS
1394 CONFIG
TIME ZONE
LANGUAGE
SYSTEM INFO
MENU INIT
OPERATION TIME
*1 Only in DV mode.
*2 Only in AVCHD mode.
*3 Only Limited functions are available in DV mode.
*4 You can display the OPTION MENU by pressing the CHK button while pressing the DISP/MODE CHK button.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback <PB> mode menu
PB MENU
PLAY SETUP
(Page 95 of Vol.2)
PB FORMAT*2
REPEAT PLAY
RESUME PLAY
SKIP MODE*2
THUMBNAIL
THUMBNAIL MODE
(Page 96 of Vol.2)
INDICATOR
DATA DISPLAY
DATE FORMAT
OPERATION
(Page 96 of Vol.2)
DELETE
INDEX*2
CLIP PROTECT*2
REPAIR*1
SW MODE
(Page 82 of Vol.2)
USER1
USER2
USER3
LCD
HDMI OUT SEL*2
DOWNCON MODE*2
VIDEO SETUP
AUDIO OUT
AV OUT SETUP
(Page 88 of Vol.2)
VIDEO OUT OSD
DATE/TIME
DATE FORMAT
LEVEL METER
CARD&BATTERY
OTHER DISPLAY
LCD SET
DISPLAY SETUP
(Page 89 of Vol.2)
EVF SET
LCD BACKLIGHT
EVF MODE
EVF COLOR
CARD FUNCTIONS
(Page 92 of Vol.2)
CARD FORMAT
CARD STATUS
CLIP PROPERTY
USER FILE
CARD READ
(Page 92 of Vol.2)
CARD WRITE
LOAD/SAVE/INIT
OTHER FUNCTIONS
(Page 93 of Vol.2)
IR REMOTE
CLOCK SET
TIME ZONE
LANGUAGE
SYSTEM INFO
OPERATION TIME
*1 Only in DV mode.
*2 Only in AVCHD mode.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Specifications
Digital zoom
2X/5X/10X
General
* Assigned to the USER button (ratio is changed
every time the button is pressed)
Minimum subject illumination
0.4 lx (F1.6, gain +30 dB, shutter speed 1/30
seconds)
Supply voltage
DC 7.2 V (when the battery is used)/
DC 7.3 V (when the AC adaptor is used)
Power consumption
Recording: 11.6 W
Lens hood
Wide field large lens hood
Shutter speed
indicates safety items.
Preset
Ambient operating temperature
0°C - 40°C (32°F to 104°F)
Ambient operating humidity
10% to 80% (no condensation)
Weight
Approx. 2.4 kg (5.3 lb) (excluding the battery and
accessories)
Dimensions (W x H x D)
180 mm x 195 mm x 438 mm (7 inches x 7-11/16
inches x 17-1/4 inches)
(excluding width, height, depth, and protruding
part)
60i/60P mode:
1/60, 1/100, 1/120, 1/250, 1/500, 1/1000,
1/2000 seconds
30P mode:
1/30, 1/50, 1/60, 1/120, 1/250, 1/500,
1/1000, 1/2000 seconds
24P mode:
1/24, 1/50, 1/60, 1/120, 1/250, 1/500,
1/1000, 1/2000 seconds
* Underline indicates value when shutter is OFF
Synchro scan
when SYNC SCAN TYPE = sec
60i/60P mode:
Camera
1/60.0 seconds - 1/249.8 seconds
30P mode:
Pickup devices
1/3 MOS fixed pickup device x 3
(2.2 mega pixels progressive supported)
Lens
Optical image stabilizer lens,
Electric/manual switching, 22X zoom,
F1.6 - 3.2 (f = 3.9 mm to 86 mm)
(35 mm conversion: 28 mm - 616 mm)
Color separation optical system
Prism format
1/30.0 seconds - 1/249.8 seconds
24P mode:
1/24.0 seconds - 1/249.8 seconds
when SYNC SCAN TYPE = deg
3.0d - 180.0d - 360.0d
(0.5d increments, angle display)
Slow shutter speed
60i/60P mode:
1/8, 1/15, 1/30 seconds
30P mode:
Filter diameter
1/8, 1/15 seconds
24P mode:
1/6, 1/12 seconds
72 mm
ND filter
OFF, 1/4, 1/16, 1/64
Minimum shooting distance
Approx. 1 m
Gain settings
0/+3/+6/+9/+12/+15/+18/+24/+30 dB
* +24 dB and +30 dB are assigned to the USER
button (S.GAIN)
Color temperature settings
ATW, ATW LOCK, preset 3200 K,
preset 5600 K, preset VAR, Ach, Bch
35
Download from Www.Somanuals.com. All Manuals Search And Download.
DV mode
„
Image/Recording/Playback
Recording format
AVCHD mode
DV standard compliant
File format
AVI Type2
Recording media
SD memory card:
„
Recording format
AVCHD standard compliant
Compression formats
MPEG-4 AVC/H.264
512 MB, 1 GB, 2 GB
(FAT12, FAT16 formats supported)
SDHC memory card:
4 GB, 8 GB, 16 GB, 32 GB
(FAT32 format supported)
SDXC memory card:
48 GB, 64 GB, up to 2 TB
(exFAT format supported)
However, it is possible to use Class 6 or higher.
Recording format (recording mode and
resolution)
(The frame rates in the setup menu are 60i, 30P,
and 24P.)
480/59.94i
480/29.97P
480/23.98P
Recording media
SD memory card:
512 MB, 1 GB, up to 2 GB
(FAT12, FAT16 formats supported)
SDHC memory card:
4 GB, 6 GB, 8 GB, 12 GB, 16 GB, 32 GB
(FAT32 format supported)
SDXC memory card:
48 GB, 64 GB, up to 2 TB
(exFAT format supported)
However, memory cards above Class 4 is
supported in PH/HA mode, and memory cards
above Class 2 is supported in PM/HE mode.
Recording format (recording mode and
resolution)
(The frame rates in the setup menu are 60P, 60i,
30P, and 24P.)
PH 1080/59.94i
Image output
PH 1080/29.97P
PH 1080/23.98P (Native recording)
PH 720/59.94P
AVCHD mode
„
HDMI OUT terminal
PH 720/29.97P
PH 720/23.98P (Native recording)
PM 720/59.94P
HA 1080/59.94i
HE 1080/59.94i
HDMI (HDMI Type A terminal)
1080/60i, 720/60P, 480/60P
(VIERA Link not supported)
VIDEO OUT terminal
Pin jack, 1.0 V [p-p], 75 Ω
480/60i
Transmission rate
PH mode: Approx. 21 Mbps (VBR)
PM mode: Approx. 8 Mbps (VBR)
HA mode: Approx. 17 Mbps (VBR)
HE mode: Approx. 6 Mbps (VBR)
Interval recording
OFF/1 s/10 s/30 s/1 min/2 min
* For the recording mode, PH 1080/24P fixed,
and shooting time has a maximum of 168 hours
(1 week)
DV mode
„
VIDEO OUT terminal
Pin jack, 1.0 V [p-p], 75 Ω
480/60i
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio recording playback
Other terminals
Camera remote terminal
AVCHD mode
„
2.5 mm diameter, super mini jack x 1 (ZOOM S/S)
3.5 mm diameter, mini jack x 1 (FOCUS/IRIS)
INDEX remote terminal
2.5 mm diameter, super mini jack x 1
TC PRESET IN/OUT terminal
VIDEO OUT terminal dual-purpose
IN: 1.0 V - 4.0 V [p-p], 10 kΩ
OUT: 2.0 V±0.5 V [p-p], low impedance
USB2.0 terminal
Memory card reader/writer function (without
copyright protection)
Compression formats
Recording/Playback:
Dolby Digital/2 ch
Sampling frequency
48 kHz
Encoding
16 bit
Compressed bit rate
PH mode: 384 kbps
PM/HA/HE mode: 256 kbps
Type mini B connector (USB2.0 compliant)
DV OUT terminal (DV mode only)
6-pin (IEEE1394 standard compliant), digital
output only
DV mode
„
Compression formats
Recording/Playback:
linear PCM (digital 2 ch)
Sampling frequency
48 kHz
Monitor
LCD
3.45 inch wide LCD color monitor
(approx. 920,000 dots)
Viewfinder
Encoding
16 bit
0.45 inch wide LCD color monitor
(approx. 1,220,000 dots equivalent)
Audio input
Built-in microphone
Stereo microphone
XLR input
XLR (3-pin) x 2 (AUDIO INPUT1, AUDIO
INPUT2), LINE/MIC selectable, high impedance
LINE: 0 dBu
AC adaptor
Power Source:
MIC: -40/-50/-60 dBu (menu selectable)
MIC POWER +48 V ON/OFF switchable
110 V - 240 V AC, 50 Hz/60 Hz
22 W
Power Output:
Audio output
7.3 V DC, 1.75 A (Camera-recorder)
8.4 V DC, 1.3 A (Charge)
Audio output
Output level: 600 Ω, 316 mV
Pin jack x 2 (CH1, CH2)
HDMI OUT (AVCHD mode only)
2 ch (linear PCM)/5.1ch (Dolby Digital)
Headphones
indicates safety items.
Weight
3.5 mm diameter, stereo mini jack x 1
Speaker
Round, 20 mm diameter
Approx. 140 g (0.31 lb)
Dimensions (W x H x D)
103 mm x 36 mm x 62 mm
(4-1/16 inches x 1-13/32 inches x 2-7/16 inches)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on Disposal in other Countries outside the European Union
EU
These symbols are only valid in the European Union. If you wish to discard
these items, please contact your local authorities or dealer and ask for the
correct method of disposal.
©Panasonic Corporation 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
|