Mold Alert
........................................................
Operation Manual
P0270
Download from Www.Somanuals.com. All Manuals Search And Download.
overview
If the air is at a relative humidity of 40%, then the dew-point
temperature is only 43°F. The walls and ceilings would therefore have
to be significantly colder for the air to reach its dew-point and for water
droplets to form.
How to achieve the correct temperature and air humidity:
Tips for active heating and ventilation:
●
●
Check the dew-point! Surfaces of walls should not fall below a
temperature of 59°F.
Avoid shutting off the heat completely when leaving the house for
extended periods of time.
●
●
Ventilate in all weather conditions, even if it’s raining.
Open the windows for a short time to air the room. A partially
opened window does not have the desired effect, wastes heating
energy and can even promote the formation of mold.
If the room air is too dry, particularly in the winter, then electrical
air humidifiers are recommended, since airing at low temperatures
will tend to decrease the humidity further.
●
●
When airing a room, a few minutes should be sufficient. Check
the value indicated on your Mold Alert thermo-hygrometer.
stArtuP
1. Select °F/°C and place the audio alarm switch on the back of the
unit in “on” mode.
2. Slide off front compartment and install 2 batteries 1.5V AA. Once
these are in place, the frowning face on the display will light up
briefly and the alarm will sound for 2 seconds.
3. Replace battery compartment cover.
4. Remove the protection film on the display.
5. The unit is now ready to use.
Download from Www.Somanuals.com. All Manuals Search And Download.
set uP
suggestions for Placement of the unit
There is an opening on the back of the unit, which allows it to be easily
hung from the wall. In addition, a base is provided for the unit to be
placed on any surface in a standing position.
Since the humidity level within rooms can vary greatly, the Mold
Alert should be placed in an area most likely subject to mold growth.
Problem areas are often basements, closets, surfaces near windows
and exterior walls. Anywhere in a home that is damp or has suffered
from water damage is also a prime location for mold growth.
reAding tHe disPlAy
Three values of measurement are displayed simultaneously.
The left column shows the indoor relative humidity (%), the middle
column indicates room temperature (°C/°F), and the right column
displays the dew point (Td).
The temperature can be displayed either in Fahrenheit or Celsius by
adjusting the °C/°F switch on the back of the unit. The audio alarm can
be activated using the “Al On / Al Off” switch on the back of the unit.
Risk of mold formation occurs at humidity levels exceeding 65%. When
this point is reached, the frowning face icon on the display will light up.
If the audio alarm is activated, it will also sound. An arrow pointing up
will be flashing next to the relative humidity display. The audio alarm
can be silenced by pressing any button.
When humidity levels are reduced below 65% the frowning face icon
will stop flashing and the alarm (if activated) will be silenced. The arrow
pointing up display will persist to indicate high humidity levels have
occured in the past. The arrow pointing up display can be reset by
pressing any button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum/Maximum temperatures
●
The highest temperature and humidity values since the last reset
can be displayed by pressing the Min/Max button on the right side
of the Mold Alert.
●
●
●
The lowest temperature and humidity levels since the last reset,
can be displayed by pressing the Min/Max button a second time.
The current values can be shown again by pressing the Min/Max
button a third time.
The reset key is located above the Min/Max button on the right
side of the unit and is used to reset Min/Max values when they
are displayed.
if humidity levels are high
●
To lower humidity, you can open windows or put a fan in the area
to better ventilate it, which may prevent mold growth.
If there is moisture or a water leak, mold growth may have
occurred. This mold can cause health problems and the sooner
you detect it, the more likely you are to be able to control it.
If you suspect that you have a mold problem, and the remedies
outlined in this manual prove to be insufficient, please contact a
mold control professional.
●
●
if humidity levels are low enough
The area in which you have placed the unit is safe from mold growth,
however the Mold Alert thermo-hygrometer is a useful product to have
in any home due to its accurate measurements of temperature, dew
point, and humidity.
MAintenAnce
●
●
●
Do not expose the Mold Alert to extreme temperatures, vibration,
or shock.
Clean the unit with a soft damp cloth. Do not use solvents or
scouring agents.
Replace batteries if the unit stops working.
Download from Www.Somanuals.com. All Manuals Search And Download.
sPecificAtions
Model:
P0270
Relative Humidity:
Room Temperature:
Alarm Trigger Point:
Display:
1% to 99% RH, accuracy ±5%
14°F to 140°F, accuracy ±1%
65% humidity triggers audio/visual alarm
User selectable F° or C°, Min/Max values
2 x AA (not included)
Batteries:
Weight:
4.8 oz.
Dimensions:
3 3/4"H x 3 3/4"W x 2 1/2"D
(Specifications subject to change without notice)
The Swiss precision hygroTECH sensor allows our Mold Alert to give
accurate measurements when checking a room’s ambient condition.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
P3 internAtionAl corPorAtion
liMited wArrAnty
P3 INTERNATIONAL CORPORATION (“P3”) warrants to the original retail purchaser
only, that its product is free from defects in material or workmanship under the condition
of normal use and service for a period of six (6) months from the date of purchase. In
the event that a defect, malfunction or failure occurs or is discovered during the warranty
period, P3 will repair or replace at its option the product or component part(s) which shall
appear in the reasonable judgment of P3 to be defective or not to factory specifications.
A product requiring service is to be returned to P3 along with the sales receipt or other
proof of purchase acceptable to P3 and a statement describing the defect or malfunction.
All transportation costs shall be borne by the owner and the risk of loss shall be upon the
party initiating the transportation. All items repaired or replaced thereunder shall be sub-
jected to the same limited warranty for a period of six (6) months from the day P3 ships
the repaired or replaced product. The warranty does not apply to any product that has
been subject to misuse, tampering, neglect, or accident or as a result of unauthorized
alterations or repairs to the product. This warranty is void if the serial number (if any) has
been removed, altered, or defaced. This warranty is in lieu of all warranties expressed
or implied, including the implied warranties of merchantability and fitness for a particular
purpose which are expressly excluded or disclaimed. P3 shall not be responsible for
consequential, incidental or other damages, and P3 expressly excludes and disclaims
liability for any damages resulting from the use, operation, improper application, mal-
function or defeat of any P3 product covered by this limited warranty. P3’s obligation is
strictly and exclusively limited to the replacement or repair of any defective product or
component part(s). Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. P3
does not assume or authorize anyone to assume for it any other obligation whatsoever.
Some states do not allow limitation on how long an implied warranty lasts, so the above
limitations may not apply to you. It is the owner/user's responsibility to comply with local,
state, or federal regulations, if any, that may pertain to P3 products or their use. This
warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
If you experience difficulty in the operation of your unit, or if your unit requires repair
please contact:
P3 INTERNATIONAL CORPORATION
TECHNICAL SUPPORT
Tel: 212-741-7289
Fax: 212-741-2288
Email: [email protected]
Rev. 1007
© 2007 P3 International Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
|