Orbit Manufacturing Smoke Alarm ORBIT 6 RP 206 User Manual

INSTALLER MANUAL

VER. B

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

by Rokonet Ltd.,

14 Hachoma Street

Rishon Letzion 75655

Israel

No part of this document may be reproduced in any form without prior

written permission from the publisher.

5IN206IM B

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Summary of User’s Commands

It is necessary to ARM your system to

obtain protection from intrusion.

This page, called a Command

Summary, is intended to give you

brief summaries of common

system operations. More detailed

explanations and related

All other forms of protection,

including fire and 24-hour panic

alarms (i.e. police, fire, and medical)

are always ready to report alarms

and do NOT need to be armed.

information can be found within, by

referring to the user manual.

FUNCTION

PROCEDURE

System Arming

Stay Home Arming

Instant Stay

System Disarming

Duress Disarming

Silencing an Alarm

[USER CODE] + [ARM]

[USER CODE] + [STAY]

[STAY] + [STAY]

[USER CODE]

[DURESS CODE]

[USER CODE]

Bypassing / Unbypassing a [ Q ] + [ 1 ] + [USER CODE ] + [ ZONE NUMBER TO BE

Zone

BYPASSED / UNBYPASSED]

Quick Bypassing Zone

[ ZONE NUMBER TO BE BYPASSED ] for at least 2 seconds

[ Q ] + [ 2 ] + [USER CODE ] + [UTILITY OUTPUT NUMBER

which is responsible for resetting the Smoke Detector]

[ Q ] + [ 2 ] + [USER CODE ] + [ UTILITY OUTPUT NUMBER ]

[ Q ] + [ 3 ]

Reset Smoke Detector(s)

Utility Output Operation

Display Troubles

Display Memory

Setting/Changing

a User Code

[ Q ] + [ 4 ]

[ Q] + [ 5 ] + [MASTER CODE] + [CODE NUMBER TO BE

SET/CHANGED] + [NEW CODE]

Set Date

Set Time

*Set Auto Arm Time

[ Q ] + [ 6 ] + [ 1 ] + [MASTER CODE] + [MM] [DD] [YY]

[ Q ] + [ 6 ] + [ 2 ] + [MASTER CODE] + [H][H] [M][M]

[ Q ] + [ 6 ] + [ 3 ] + [MASTER CODE] + [H][H] [M][M]

Set Follow-Me Phone No. 1 [ Q ] + [ 7 ] + [ 1 ] + [MASTER CODE] + Phone No. + [ #]

Set Follow-Me Phone No. 2 [ Q ] + [ 7 ] + [ 2 ] + [MASTER CODE] + Phone No. + [ #]

**Set Follow-Me Phone No. 3 [ Q ] + [ 7 ] + [ 3 ] + [MASTER CODE] + Phone No. + [ #]

**Set Follow-Me Phone No. 4 [ Q ] + [ 7 ] + [ 4 ] + [MASTER CODE] + Phone No. + [ #]

Maintenance:

On/Off Buzzer

[ Q ] + [ 8 ] + [MASTER CODE] + [1]

[ Q ] + [ 8 ] + [MASTER CODE] + [ 2]

[ Q ] + [ 8 ] + [MASTER CODE] + [ 3]

On/Off Door Chime

*On/Off Audible Kiss-Off

Indication

Get Event From Event

Logger

[ Q ] + [ 9 ] + [MASTER CODE] + [EVENT NO.]

Test System

[ Q ] + [ 0 ] + [MASTER CODE]

LED

Trouble

Low Battery

AC Power Loss

Clock Not Set

Communication Trouble

Bell Loop Trouble

Trouble Table

*New in Version 1.2

**New in Version 1.3

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

Introduction to the ORBIT-6..................................................................6

Main Features:..................................................................................6

Installation............................................................................................7

Before You Begin..............................................................................7

Technical Data.....................................................................................8

Installer Programming ..........................................................................9

The keypad.......................................................................................9

Restoring Factory Defaults to the ORBIT-6 .......................................9

Introduction to Programming.............................................................9

Programming your Orbit-6...............................................................10

Viewing the Contents of a Location.................................................11

Locations Whose Contents Occupy More Than One Digit ...............12

Audible Tones and Error Beeps ......................................................12

How to program installer parameters...............................................12

A Programming Tutorial..................................................................12

GENERAL SYSTEM PARAMETERS: Locations 00–05 ....................14

SYSTEM CODES: Locations 06-10 ..................................................15

SYSTEM TIME: Locations 11-13 ......................................................16

Intrusion Zone Types and Zone Sounds: Locations 14-21..................16

SPECIAL ZONE TYPES:....................................................................18

Utility Outputs: Locations 22-25........................................................19

Communication Parameters: Locations 20–21....................................22

Digital Communicator Controls: Location 26....................................22

Central Station Protocols: Location 27-28......................................23

Understanding the Code Format.....................................................24

Upload/Download Rings: Location 29............................................25

System Controls: Location 30...........................................................25

Periodic Test Time: Location 31 .......................................................27

Communicator Reporting Codes: Locations 32 through 85.................27

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION TO THE ORBIT-6

The ORBIT-6 is intended to address the needs of many homes, offices, and small

businesses. Its operation is designed around microprocessor and EEPROM

(Electrically Erasable Programmable Read-Only Memory) technology, which stores,

without the need for a source of power, the system’s operating program and its

programmable parameters.

System programming may be performed from any ORBIT-6 keypad, or from a special

LCD Programming Keypad designed specifically for that.

Remote and local system programming is also possible through the use of Rokonet’s

ORBIT Upload/Download software.

Main Features:

Zones (end-of-line resistor required 2200 ohm)

6 Programmable Intrusion Zones

Special type: Zone 5 – Fire Zone, Zone 6 - tamper zone

One Fixed Panic Zone input on the keypad (not on keypad RP206KL6)

3 Keypad Emergency Zones (Panic, Fire, Special Emergency)

Alarm Sounder Output

Programmable Bell/Siren or Loudspeaker Output

Capacity: 750 mA (maximum)

Auxiliary Output for Peripheral Devices

Capacity 250 mA (maximum)

Built-In Digital Communicator

For Central Station communications (two phone numbers)

For Upload/Download functions

For follow-me functions

Keypads

Up to 4 LED/LCD keypads can be connected

Utility Outputs

One transistor-driven (open-collector) triggered output

Security Codes

Two Installer Codes

One Master (User) Code

Nine User Codes (all may be used as duress code)

Periodic Testing

Daily test report to central station

Optional Peripherals

Four relay outputs expansion

Voice Module

Event Log

Event log of 100 events

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Before You Begin

Be sure the actual work is performed by experienced personnel, licensed to carry out

security system installations and capable of implementing all applicable requirements of the

National Fire Protection Association (NFPA-70 and NFPA-74), as well as any federal, state,

and local codes–along with any safety guidelines and regulations which might apply.

Mounting and Wiring the Control Panel

(refer to figures 1A, 1B & 1C on pages

32, 33 & 34)

1. Mount the ORBIT-6’s metal cabinet at a protected dry location, near a source of

unswitched AC Power, a good ground, and access to telephone service. Use the proper

hardware (e.g. anchors, mollys, toggle bolts, etc.), as required, to insure a suitable

mounting.

2. Thread all electrical wiring through a convenient hole in the metal cabinet. To prevent

potential damage, be sure that live AC power is NOT present and that the Standby

Battery is NOT connected. Refer to Figures 1A and 1B. Your wiring may include any

and all of the following:

· connections to Hardwired Zones

· connections to devices requiring Uninterrupted Auxiliary Power (e.g. PIRs, Glass

Break Detectors)

· connections to Smoke Detectors requiring Resettable Power

· connections to any External Sounders

3. If using Utility Output, connect the UO/ECL output, this terminal is designed to activate a

low current device (e.g. a 12 VDC Relay, drawing no more than 70 mA).

If using UO expansion module, connect the UO/ECL terminal to the ECL terminal input

in the expansion module. In this case the first UO on the expansion module will become

UO1. (see figures A1)

4. Make connections from the RJ31X (or equivalent) telephone company interface.

5. Make connections to the system’s keypad(s) by the correspnding wire colors.

6. Make connections to AC Power (via a 16.5 VAC, 25 VA transformer). Do not plug in the

transformer at this time.

7. Have a Standby Battery ready (typically 12 VDC, 4 AH), but do not connect it at this

time.

8. All zone inputs are End Of Line supervised, use 2200 ohm resistors (supplied).

9. When using 8 LED keypad, zones 7 & 8 are end-of-line supervised. Use 2200 ohm

resisters (supplied) when the zones are not in use. For further wiring instructions of the

8 LED keypad, refer to Figure 1C on page 34.

10. If using a Key-switch, use a momentary key-switch. The receiver (if used) must give a

pulse output and not on/off.

11. To connect the panic button use the white wire as (+) and the black wire as (-).

Note: The maximum distance between the panic button and the keypad is 30 meters.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL DATA

Main Panel

Input power

16.5 V AC 25 VA via transformer

12 V 4 A-Hours

Rechargeable standby battery

Auxiliary Power

Bell/LS Sounder output

Programmable output

Cabinet Dimensions:

Weight

12 V DC 250 mA maximum

12 V DC 750mA maximum

Open collector Active pull down 70mA maximum

260X218X83 mm (10.2X5.1X3.3 “)

1.84 kg (4 lb)

Main Board (dimensions / weight):

Fuse F1

Fuse F2

80X167 mm (3.15X6.6 “)

Auxiliary Power

Bell/LS Power

0.17 kg (0.37lb)

0.5 A

1 A

Fuse F3

Battery Power

2 A

Keypads

6-Zone Keypad

8-Zone Keypad

Current consumption:

Control panel

connections:

Dimensions:

Weight:

18 mA typical, 30 mA maximum

4-wire up to 300 ft (100 m) from

panel

110X130X25 mm (4.3X5.1X1 “)

0.19 kg (0.42 lb)

18 mA typical, 30 mA maximum

4-wire up to 300 ft (100 m) from

panel

110X130X25 mm (4.3X5.1X1 “)

0.19 kg (0.42 lb)

Utility Output Expansion Module

Relay

Transistor

Current consumption:

Control panel connections:

Contacts:

10mA typical, 50mA max

4-wire up to 300 ft (100m) from panel

4 relays, 0.5 A, 24 V DC

10mA typical, 15mA max

4 O.C., 50 mA, 12 V DC

Dimensions:

53X85 mm (2.1X3.35 “)

Weight:

80 gr (0.18 lb)

Max. Run Length from Panel to Keypad

Wire

AWG

Ø (mm)

Meter

Feet

0.6

100

330

0.9

200

660

0.8

166

547

Length

Bell Loudspeaker Wiring Table (Distance in Feet)

AWG

0.8

0.6

0.9

Ø mm

Max.

Current mA

Feet

Meter

Feet

Meter

Feet

Meter

Feet

Meter

100

300

650

780

260

120

238

625

208

190

495

165

151

310

103

Detectors Distance in Feet

AWG

0.9

0.8

0.6

0.5

Ø mm

Max.

Current mA

Feet Meter Feet

3920 1195 3100

Meter

Feet

Meter

Feet

Meter

Feet Meter

945

628

472

2460

1640

1230

750

500

375

2460

1640

1230

472

314

236

1550

1030

775

296

197

148

2600

1960

793

597

2060

1550

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLER PROGRAMMING

The keypad

The Orbit-6 can support up to 4 keypads, with

a choice of 3 styles, 1 LCD type and two LED

types from which virtually all features may be

accessed. In addition to the functions it

provides for the user, each of the keypads can

be used by an installer to program the system

parameters.

An attempt to enter an incorrect series of

keystrokes will result with 3 error beeps.

All program location values (data) are

displayed by zone indicators on the LED

keypad in binary format.

Restoring Factory Defaults to the ORBIT-6

1. Your ORBIT-6 and at least one LED Keypad should already be wired together

and/or physically installed

2. Remove all power from the Printed Circuit

3. Place the ORBIT-6’s J1 (DEFAULT) jumper over both corresponding pins. (See

Figures 1A and 1B on page 32 and 33 ).

4. Reapply power (AC and/or Standby Battery) to the PC Board.

5. After a short beep is heard, remove the J1 jumper. The ORBIT-6’s default settings

are now restored.

6. Check that the POWER LED is flashing. Depending on the state of the system, the

READY LED and the Zone LEDs may or may not be lit.

Introduction to Programming

First, check that the panel’s J1 (DEFAULT) jumper is NOT covering both pins on the

PC Board.

The ORBIT-6 stores information in 86 programming locations.

The data stored in any location is represented by numbers and/or letters. Some

locations require just one digit, while most require two. Others (e.g. those used to

store phone numbers and account numbers) may require several more digits.

It is not necessary to enter data into all 86 categories. Many locations have been

factory-programmed with default parameters.

Note that power can be removed from the ORBIT-6, as its memory does not require a

source of power to retain its information.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming your Orbit-6

Programming Methods

Local

Requirements

LED or LCD keypads

The keypad must be wired to the Orbit-

6 panel.

Power must be applied to the Orbit-6.

Orbit Programmer

Easy programming of the control panel The programmer will be connected and

parameters with menu driven LCD receive its power from the panel.

display.

The programmer can store up to 10

Orbit-6 programming sets and copy it

directly to the panel. The programmer

supports both the Orbit-5 and Orbit-6

panels.

Orbit UD*

Local Up/Load Windows version from a The software must be installed and an

personal computer.

Orbit UD Adaptor cable is connected

between the panel and the computer.

Requirements

Remote

Orbit UD*

Remote U/D Windows version from a

personal computer.

The software and applicable modem

with configured access to a telephone

line must be installed.

* Compatible with Windows 95/98/2000 & NT.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Viewing the Contents of a Location

It’s often necessary to check the data stored in a memory

location to be sure it’s correct. If improper data is found, it must

be corrected in order to obtain the desired system response. The

data in a location can either be a number (from 0-9) or a letter

(from A-F). Doing so takes advantage of the hexadecimal

numbering system. For our purposes, the characters A through F

will be referred to as hexadecimal digits.

Whenever the Installer Programming mode is active, the first 4

keypad’s Zone LEDs (1-4) are used to reveal each digit in a

selected location. By adding up the values assigned to the lit

LEDs, the contents of any location can be determined. See table

below.

ZONE LEDs

I.D.:

Value: 8

I.D.:

value: 8

off

EXAMPLE: Zone 4-ON Zone 3-off Zone 2-off Zone 1-ON

EXAMPLE: Zone 4-ON Zone 3-off Zone 2-ON Zone 1-ON

TOTAL = 9

TOTAL = B

Hexadecimal Digits

In some locations you may be

required to enter hexadecimal

digits A - F to do so see the next

table.

“A” is entered by pressing [STAY] + [1]

“B” is entered by pressing [STAY] + [2]

“C” is entered by pressing [STAY] + [3]

“D” is entered by pressing [STAY] + [4]

“E” is entered by pressing [STAY] + [5]

“F” is entered by pressing [STAY] + [6]

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Locations Whose Contents Occupy More Than One Digit

When a location contains more than one digit, they cannot be viewed

simultaneously. As soon as a location is accessed, the first digit is displayed

automatically. Additional digits (if they exist) can be displayed by pressing the

following keys:

Used to display the next digit in a location containing at least two

digits; e.g. if 5-6-7-8 is stored in a location, the “5” is displayed first;

by pressing

, the “6” will be displayed; continue this

process to display the entire contents of the chosen location. Error

beeps will be produced when it’s attempted to display digits which

don’t exist

Used to move backwards among the digits stored in a location

containing at least two digits. Error beeps will be produced when it’s

attempted to display digits which don’t exist

Audible Tones and Error Beeps

To confirm an operation, a single, long beep will be heard. However, any improper use

of the keypad resulting in an error or an unacceptable response will produce three

rapid beeps. If heard, repeat the operation or exit the programming mode and try again.

How to program installer parameters

1. To enter the Installer programming mode:

Press 4 digit Installer code followed by # (factory default 0 2 0 6)

2. To move to a new location:

Press two digits of location followed by ARM

3. To enter data into the location:

Press data digits (0 - 9 digits including hexadecimal A-F) followed by #

4. To exit programming mode:

Press 4 digit installer code followed by ARM

A Programming Tutorial

To get acquainted with some programming basics, a short tutorial has been

prepared. It involves changing the Installer Code from the factory default of 0-2-0-

6 to a sequence of your own choosing. If you can master this operation,

subsequent programming should be easy.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Action

enter the factory default

Installer Code (0-2-0-6);

followed by #

Comments

a long beep will sound, confirming

successful entry into Installer

Programming

Enter the

Installer

Programming

mode

Access the

current Installer

Code

(stored in location

“08”)

Enter a unique

Installer Code

(for this tutorial,

we’ll use 3-0-5-7)

Store the data

you have entered

press [0], [8], [ARM]

no confirming beep will sound

enter [3], [0], [5], [7]

press [#]

a long beep will sound confirming that

data has been properly stored

if a wrong number of digits entered

three (error) beeps will sound after

pressing #

Check the data

stored in Location

“08”

· the first digit of the stored

data will appear

press

keys

displayed

zone

LEDs

lit

value

· observe the Zone LEDs

· press [STAY] [STAY] to

advance to the next digit

· once all four digits have

been displayed, attempts to

view an additional digit will

result in three (error) beeps

· if desired, press [STAY]

and [ARM] to move

none

1^stdigit

2^nddigit

3^rddigit

4^thdigit

2, 1

none

3,1

STAY

3,2,1

backwards

Go to another

location of your

choice

Exit

programming

press the desired two-digit

location and [ARM]

press [ARM] alone to go to the next

sequential location

enter your Installer Code

and press [ARM]

a long beep will confirm your actions

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL SYSTEM PARAMETERS: LOCATIONS 00–05

Location: 00 Default Enable: Def: 00

PURPOSE: to enable or disable the option of resetting the system to the factory

defaults.

Enable the option of resetting the system to the factory defaults.

Disable the option of resetting the system to the factory defaults.

Location: 01 MS Lock: Def: 000000

§ MS Lock is a 6-digit security code used in conjunction with Rokonet’s

Upload/Download Software

§ It is designed to provide greater proprietary security to the Central Station

parameters

§ It is NOT necessary to change the MS Lock default value within Installer

Programming; instead, the procedure may be performed from the

Upload/Download Software and then downloaded to the ORBIT-6

for additional information, refer to the Upload/Download Programming

Manual

Location: 02 Phone Number: Primary Central Station (Central Station 1)

To delete an existing phone number, simply press the [#] key; to enter or replace the

phone number required to reach the primary Central Station include all access digits

(e.g. 0 to 9) and the area code. If required, include the following special functions to

achieve the effect listed in the table:

RESULTS

FUNCTION

SEQUENCE

[STAY], [1]

[STAY], [2]

[STAY], [3]

stop dialing and wait for a new dial tone

wait a fixed period before continuing

switch from Pulse to Tone (or from Tone to Pulse)

send the DTMF Q character

[STAY], [

]

send the DTMF # character

[STAY], [#]

When done with your complete entry, press [#] to store it. Up to 24 digits can be

entered to the phone number.

For your records, enter the complete phone number below:

Location: 03 Phone Number: Secondary Central Station (Central Station 2)

Same as in Location 02

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Location: 04 Callback UD Phone #

Enables greater security for remote Upload/Download operation. This is a number to

which the alarm company computer, equipped with the U/D software, will be

connected.

When a call is made from a computer, using U/D software, to the Orbit-6 panel, the

system will hang-up and call back using this UD phone number. Up to 24 digits can be

entered into the U/D phone number, include all the digits and functions as above in

Location 02. To delete an existing phone number press #.

Location: 05 Account Number

Default: 0000

PURPOSE: to assign the system’s Central Station Account Number

hexadecimal account numbers (those using 0 through 9 and A through F) are

accepted by the ORBIT-6; use the key combinations below to enter hexadecimal digits

“A” through “F”:

hex digit

press

hex digit

press

Acct No.

[STAY], 1

[STAY], 2

[STAY], 3

[STAY], 4

[STAY], 5

[STAY], 6

“0” will not send a digit to the central station, to send “0” use “A” digit

SYSTEM CODES: LOCATIONS 06-10

Location: 06

Access Code

Default: 5678

PURPOSE: to provide data security during Upload/Download operations

this same Access Code must subsequently be entered into the corresponding account

profile in the Upload/Download software (along with the Remote ID codes, see

Location 07, below).

Access Code

Default: 0001

Location: 07

Remote ID Code

PURPOSE: to provide data security during Upload/Download operations this same

Remote ID Code must subsequently be entered into the corresponding account profile

in the Upload/Download software.

Remote ID

Location: 08

Installer Code I

Default: 0206

PURPOSE: the installer code is used by alarm company personnel authorized to

modify the system’s parameters It is recommended to change the “factory default”

Installer Code to one of your own choice.

Installer Code

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Location: 09

Installer Code II

Default: 1206

Same as the Installer Code 1, but with a few limitations: It can't modify the "default

code", observe and modify the first installer's codes, modify any MS phone number,

nor observe & modify MS lock code.

Installer Code

Location: 10

Master Code

Default: 1234

PURPOSE: to establish the keypad code for the system’s “chief user”; the

Master Code provides the following special privileges:

· to enter, modify, and delete the remaining nine User Codes

· to set the system's internal clock

Master Code

· to perform certain system functions and tests

Note: the Master Code cannot be seen by the installer through the zone LEDs on the

keypad.

SYSTEM TIME: LOCATIONS 11-13

Location: 11

Exit Delay

Default: 030

PURPOSE: to establish the system’s Exit Delay (the interval, in seconds, between

entering a User Code at the keypad and when the system actually arms).

Enter three digits between 001 and 255 seconds

Exit Delay

Location: 12

Entry Delay

Default: 060

PURPOSE: to establish the system’s Entry Delay (in an armed system, the interval, in

seconds, between the moment an entry door is opened and an alarm is triggered).

Enter three digits between 001 and 255 seconds

Entry Delay

Location: 13

Bell Cutoff Time

Default: 04

PURPOSE: to set the interval that the system’s external sounder(s) will operate before

it shuts off automatically.

Enter the number of minutes between 01 and 90

Sounder

Cutoff

INTRUSION ZONE TYPES AND ZONE SOUNDS: LOCATIONS 14-21

Locations 14 through 21 are identical and are corresponding to Zones 1 through 6 or 8

(in the 8-zone keypad), respectively. Each of these locations contains two digits.

the first digit: Contains the number used to represent the Type of Zone desired

the second digit: Contains the number used to represent the sound produced

when in alarm

Note: 1. When using 6 zone keypad the system disregards zones 7 - 8.

2. When using 8 zone keypad, zones 7 - 8 must be connected to an EOL

resister when not in use.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Locations: 14-21

1^stDigit

Zone 1-8: (1^stDigit): Type

Zone Type and Comments

Default:

Not Used

All unused zones should be given this designation. It is also used to disable a zone

24-Hour

A violation of such a zone will always cause an instant intrusion alarm, regardless of

the system’s armed/disarmed state

Instant (Intrusion)

Causes an immediate intrusion alarm if violated when the system is in arm state. Entry

Delay.

Entry/Exit Delay

If violated, a zone with this designation will not cause an intrusion alarm during the

Entry and Exit Delay periods

Exit (OPEN)/Entry

Such a zone behaves as described above in Entry/Exit Delay, except that if faulted at

the time the system is armed, it will be bypassed and NOT prevent system arming.

To avoid an intrusion alarm, however, it must be secured before the expiration of the

Exit Delay period (Location 11).

Entry Follower

A zone(s) given this designation will cause an immediate intrusion alarm when violated

unless an Entry/Exit zone was violated first if so, an Entry Follower zone(s) will remain

bypassed until the end of the Entry Delay period

Interior + Entry Delay Follower

If the system is armed to AWAY (ARM) mode: this type of zone behaves like the Entry

Follower, described above

If the system is armed to the STAY mode: this type of zone will be bypassed

Important Note: When arming with "STAY" mode it is possible for the user to eliminate

the entry delay period by pressing the (STAY) key twice in succession when arming

the system.

Fire Zone

Intended for smoke or other types of fire detectors. If violated, will cause an immediate

fire alarm. Only Zone 5 can be programmed as a fire zone. A fault in the wiring of any

fire zone, if supervised, will cause a fire alarm, manifested by a rapid flushing of the

keypads' Fire LED.

Tamper Zone

Only Zone 6 can be a Tamper Zone. It operates the same as 24 hours Zone, but this

type has a special reporting code.

Panic Zone

If violated an immediate panic alarm will be announced.

Key-switch Zone - Instant

If desired for system arming and disarming an external SPST spring - loaded,

normally open, momentary type key switch can be added. The key switch permits an

instant arm and disarming of the system after tripping.

Key-switch Zone - Delayed

Such a zone behaves as described above in "key switch zone instant", except when

arming the system an exit delay will follow.

Latch-Key-switch Zone – Instant: If desired for system arming/disarming, connect

an external SPST latching type (non-momentary) key-switch to any zone terminals,

given this designation.

**C

Latch-Key-switch Zone – Delayed: Such a zone behaves as described above in

"latched key switch zone instant", except when arming the system an exit delay will

follow.

**D

** New in Version 1.3

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Locations: 14-21

Zone 1-8: (2^ndDigit): Sound

Default:

2^ndDigit Zone Sound and Comments

Silent

a violation during the armed period will produce no sound

the resulting alarm can still be reported to the Central Station

External Sounder (Continuous)

causes the external sounding device to annunciate steadily, without breaks in the

sound cadence the sound will continue until the sounder “times out” or the system is

disarmed

(default)

External Sounder (Pulses)

causes the external sounding device to produce a pulsed (or staggered) annunciation

this sound is usually recommended for fire alarm annunciation

Keypad Sounder Only

causes the piezo sounder within the system’s keypad(s) (only) to beep rapidly

External Sounder + Keypad Sounder

causes the external sounding device to annunciate continuously, without breaks in the

sound cadence causes the piezo sounder within the system’s keypad(s) to beep rapidly

External Sounder When Armed / Keypad Sounder When Disarmed

related to 24H zones

when alarm during disarm, the keypad’s buzzer will be activated

when alarm during armed system, the external sounder will be activated

Door Chime

assigned to an opening which, when violated during the disarmed period, will cause the

system’s keypad(s) to beep once during an alarm, the external sounding device will

annunciate continuously, without interruption. When alarm occurs during armed system

only the external sounder will be activated.

Zone Location

Type

(3)

(5)

(2)

(6)

(2)

(0)

Sound

(1)

(0)

* (x) define the type and sound default

SPECIAL ZONE TYPES:

Location: 18 Zone 5: Fire Zone

Zone 5 is reserved as a Fire Zone, supports four-wire Smoke Detectors. Smoke

Detector power must be interruptible in order to reset a detector “latched” in alarm. As

such it should be derived from the UO/ECL or one of the UOs terminal (see Figures 1A

and 1B). The related UO should be defined as AUX power switch.

Location: 18 Zone 5: (1^stDigit): Type

Default: Fire

1^stDigit

Zone Type and Comments

Fire

A fire zone cannot be disabled or bypassed.

A fault in the wiring to the zone will cause a Fire Trouble (fire LED blinks).

A short in the zone wiring will cause a fire alarm.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Location: 18 Zone 5: (2^ndDigit): Sound

Default: External Sounder (Pulses)

For fire zone the recommended (default) zone sound is “External sounder pulsed”

However it is possible to change the zone sound and type to any of the ones provided in the

previous list.

Location: 19 Zone 6: Tamper Zone

Zone 6 is reserved as a Tamper Zone. This zone can be programmed to any zone type (except

Fire) including Tamper. If the zone was programmed as Tamper, in violation, a Tamper Code

report will be sent and the Tamper LED on the keypad (marked as 6/Tmp) will light up.

UTILITY OUTPUTS: LOCATIONS 22-25

The ORBIT-6 supports one open collector Utility Output (derived between the UO/ECL and AUX

terminals) which can be used for switching an external device on or off. Once the Utility Output is

activated the device will be connected between AUX (+12V) and ground (0V). This connection is

capable of switching light loads of no more than 70mA.

Note: When activated the utility output is switched to the Negative Polarity.

The “UO” can be also used to reset a “latched” Smoke Detector(s). In that case the 12V power to

the smoke detector will be supplied via the UO (see Figures 1A and 1B). The UO should be

defined as AUX switch.

If the Utility Output Expansion Module is being used, the same information in Location 22 is

applicable for the programming of UO2 (Location 23), UO3 (Location 24), and/or UO4 (Location

25). It is not necessary to program all of the available “UOs”, unless they’re used. Note that

when the Utility Output Expansion Module is employed, the original Utility Output on the Main

Board (the UO/ECL terminal) is no longer available.

Important: In order to use the Utility Output Expansion you have to define the module in

Location 30.

Because of the “UO’s” modest 70 mA

current capability, it will be necessary to

use

“intermediate”

relay-whose

physical contacts can switch far greater

currents (limited by their contact rating).

The figure at the left shows how such a

relay can trigger a strobe light. If used in

this manner, the “UO” cannot be used to

reset a “latched” Smoke Detector(s).

If more than one “UO” output is necessary, a

Utility Output Expansion Module is available. Its

four “UOs” (U01, UO2, UO3, and UO4) replace

the ORBIT-6’s single “on-board ”UO”. The “UOs”

on the Utility Output Expansion Module are

relay-based, and allow a maximum current of

500 mAs. Refer to Figures 1A and 1B (pages 32

and 33), for wiring instructions and additional

information. The figure at the right, shows how a

Utility Output on the “UO Expander” can be used

to switch a table lamp on and off.

23)

16.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Digit Event and Result

Not Active

UO offers no response to any system activity

(default)

Arm Follow (Latch)

U0 is activated when the system is armed. The activation occurs after the expiration of

the exit/delay period. The U0 remains active (latched) while the system is armed. When

disarming the system the U0 deactivates (unlatches).

Arm Follow (Pulse)

UO is activated when the system is armed. The activation occurs after the expiration of

the exit/delay period. The UO is activated for several seconds (pulse), after which is

deactivated.

Alarm Follow (Latched)

UO is immediately activated when the system goes into any type of alarm (i.e. intrusion,

fire, keypad-initiated panic) UO remains active (latched) for the duration of the

alarm-even after the system’s sounder “times out” UO is deactivated when the system is

disarmed

Alarm Follow (Pulse)

UO is immediately activated for several seconds and then deactivated whenever the

system goes into any type of alarm (i.e. intrusion, fire, keypad-initiated panic)

Zone 1 Alarm Follow (Latched)

U0 is immediately activated when an alarm occurs on Zone 1. U0 remains active

(latched) for the duration of the alarm - even after the system sounder "times out". U0 is

deactivated when Zone 1 goes into normal condition.

Zone 1 Alarm Follow (Pulsed)

U0 is immediately activated for several seconds (pulsed) and then deactivates whenever

Zone 1 goes into alarm.

Zone 2 Alarm Follow (Latched)

Zone 2 Alarm Follow (Pulsed)

Zone 3 Alarm Follow (Latched)

Zone 3 Alarm Follow (Pulsed)

Zone 4 Alarm Follow (Latched)

Zone 4 Alarm Follow (Pulsed)

Zone 5 Alarm Follow (Latched)

Zone 5 Alarm Follow (Pulsed)

Zone 6 Alarm Follow (Latched)

Zone 6 Alarm Follow (Pulsed)

Zone 7 Alarm Follow (Latched)

Zone 7 Alarm Follow (Pulsed)

Zone 8 Alarm Follow (Latched)

Zone 8 Alarm Follow (Pulsed)

Panic Follow (Latched)

UO is activated immediately when a PANIC alarm is triggered by a violation of a zone,

defined as Panic, or by pressing the keypad’s [1] and [2] keys simultaneously for two

seconds. U0 is deactivated when the system is disarmed.

Panic Follow (Pulse)

UO is activated for several seconds when a PANIC alarm is triggered by a violation of a

zone, defined as Panic, or by pressing the keypad’s [1] and [2] keys simultaneously for

two seconds.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Special Emergency Keying Follow (Latched)

UO is activated immediately when pressing the keypad’s [7] and [8] keys simultaneously

for two seconds. U0 is deactivated when the system is disarmed.

Special Emergency Keying Follow (Pulsed)

UO is activated for several seconds when pressing the keypad’s [7] and [8] keys

simultaneously for two seconds.

Fire Keying Follow (Latched)

UO is activated immediately when a Fire alarm is triggered by a violation of zone 5,

defined as Fire, or by pressing the keypad’s [4] and [5] keys simultaneously for two

seconds. U0 is deactivated when the system is disarmed.

Fire Keying Follow (Pulse)

UO is activated when a Fire alarm is triggered by a violation of zone 5, defined as Fire,

or by pressing the keypad’s [4] and [5] keys simultaneously for two seconds.

User Activated (Toggle)

UO may be activated by the user through the entry of [*]+[2]+[User Code]+[X], where X

refers to the utility output number.

The first entry of the above sequence activates the UO and causes it to latch in the

opposite of its current state. The system briefly lights the Zone LED corresponding to the

selected UO and produces a single confirming beep subsequent entries toggle the

response from ON to OFF to ON, etc.

User Activated (Pulse)

UO may be activated by the user through the entry of [*]+[2]+[User Code]+[X], where X

refers to the utility output number.

The entry activates the UO for several seconds (pulse). The system briefly lights the

Zone LED corresponding to the selected UO and produces a single confirming beep

subsequent entries repeat this pattern.

AUX POWER Switch (Fire)

Until triggered, UO is normally activated and is designed to be a part of the circuit

supplying power to the Smoke Detector(s); see Figure 1A and 1B.

After a Fire Alarm is disarmed, it may be necessary to reset any Smoke Detector(s)

which may be “latched” in alarm. A “latched” Smoke Detector will cause the keyboard’s

FIRE LED to remain lit, even though the panel may be disarmed. To reset a Smoke

Detector, a “UO” used in this manner must be momentarily deactivated; this action is

performed by the user, who must enter [*]+[2]+[User Code]+[X], where [X] refers to the

UO number (i.e. 1,2,3, or 4) in the circuit providing Smoke Detector power. If this is not

done, it will be impossible to arm the panel; please advise your customer of this

contingency which is stated in the ORBIT-6’s User Manual.

Duress Code Follow (Pulse)

U0 is activated for several seconds (and then deactivates) when any duress code is

entered.

AC Loss Follow (Latched)

U0 is activated due to a lack of power from the commercial AC. U0 is deactivated when

the system is operating properly from commercial (AC) power.

AC Loss Follow (Pulse)

U0 is activated for several seconds (and then deactivates) due to a lack of power from

the commercial AC.

Low Battery Follow (Latched)

U0 is activated due to low power from the backup battery. U01 is deactivated when the

battery is in good condition.

Low Battery Follow (Pulse)

U0 is activated for several seconds due to low power from the backup battery.

Voice Module Enable

The U0 is activated after FM phone number dialing has been made due to alarm. The U0

deactivates after the FM period termination.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Duress Code Follow (Latched)

UO is activated when any duress code is entered. The UO deactivates either when

arming the system or disarming the system due to an alarm that was activated from the

emergecy keypad keys, 24-hour zone violation or tamper zone violation.

Follow Chime (Pulse) (Ver. 1.2) UO is activated for several seconds whenever a

keypad sounds its chime.

Follow Bell Latched NO (Ver. 1.2) UO is activated whenever the bell is activated. UO

is deactivated at the bell cut-off time.

Follow Bell Latched NC (Ver.1.3)

Follow Ready NO (Ver.1.3) UO is activated whenever the system is in the ready state.

Locations:

UO1

UO2

UO3

UO4

Action

COMMUNICATION PARAMETERS: LOCATIONS 26–29

Locations 26 and 27 allow you to define the manner in which the ORBIT-6 communicates with the

Central Station when it reports alarms, restorals, troubles, openings/closings, and tests.

Digital Communicator Controls: Location 26

· First digit: determines the number (or hexadecimal digit) corresponding to the

Dialing Method / Duty Cycle / Redial Time desired

· Second digit: determines the number corresponding to the

Attempts / Answering Machine Use / UL Installation

Answering Machine

in Use

Attempts

UL Installation

Voice Module

Attempts sets the

If enabled to defeat an

If the ORBIT-6 is installed If enabled (“YES”) voice

number of times the answering machine, two in accordance with UL

ORBIT-6 will redial phone calls must be requirements, for a

the Central Station made to the premises. On Residential Installation

messages will be sent. If

“NO” then tones will be

used to represent an active

after failing to

establish a

the first call let the phone (UL 1641), the operation of alarm.

ring once (by pushing the the unit’s Digital

successful

space bar on the U/D

Communicator must be

communication.

software keyboard). The modified so as to disable

panel detects this ring

and starts a 60sec timer

during which the panel

will answer the next call

on the first ring.

features, which are

inappropriate.

Location: 26

Dialer Controls: (1^stDigit):

1^stDigit

Dialing Method

DTMF

Duty Cycle

* Redial Central Station

after 60 seconds

after 30 seconds

after 60 seconds

after 30 seconds

after 60 seconds

after 30 seconds

after 60 seconds

after 30 seconds

after 60 seconds

N/A

Pulse @ 20 pps

DTMF

Pulse @ 20 pps

Pulse @ 10 pps

67/33

N/A

61/39

67/33

61/39

4 (default)

* redial refers to the number of seconds the ORBIT-6 will wait before redialing a busy or unresponsive Central Station

phone number.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Location: 26

Dialer Controls: (2^ndDigit):

2^ndDigit

Attempts

Answering Machine

UL Installation

Voice Module

Yes

(default)

Yes

Central Station Protocols: Location 27-28

(PPS)

Kissoff/

InterDigit

Time

Code

format

Format Name

Validation

Dual round

pulses/sec Handshake

Silent Knight/

ADEMCO Slow

1400Hz

650

Silent Knight/

ADEMCO Slow Extended

Radionics/DCI/ Franklin slow

Silent Knight Fast

2300 Hz

1400 Hz

Dual round

650

Silent Knight Fast Extended

1400 Hz

2300Hz

Dual round

650

Sescoa/Franklin/Vertix/ DCI fast

Sescoa/Franklin/Vertix/DCI

Extended

2300Hz

Dual round

650

Universal high speed

2300Hz

1400 Hz

2300Hz

1400 Hz

2300Hz

1400 Hz

2300Hz

1400 Hz

2300Hz

1400 Hz

2300Hz

1400 Hz

2300Hz

Dual round

Parity

390

Radionics

Radionics Extended

Radionics

Radionics Extended

Radionics

Parity

Radionics Extended

Parity

Example: to use ADEMCO slow enter 0F to location 27

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Understanding the Code Format

To understand and modify the Code format according to a specific central station see the

following

First digit: determine the number corresponding to the desired combination of:

Kissoff/Handshake Freq / Message Validation / Extended–Non-Extended Format)

· Second digit: determine the number (or letter) corresponding to the desired combination

of: Dialing Rate / Interdigit Time / Data Frequency

Location: 27

CS Protocols: (1^stDigit):

1^stDigit

Format

Kissoff/Handshake Freq

Message Validation

Non-Extended

1400 Hz

Dual Round Compare

(default)

Non-Extended

Extended

2300 Hz

1400 Hz

2300 Hz

1400 Hz

2300 Hz

1400 Hz

2300 Hz

Dual Round Compare

Parity

Dual Round Compare

Parity

Extended

Parity

Location: 27

CS Protocols: (2^ndDigit):

2^ndDigit

Data Rate

Interdigit Time

Data Frequency

40 pulses/sec

390 ms

1800 Hz

(default)

33 pulses/sec

20 pulses/sec

10 pulses/sec

40 pulses/sec

33 pulses/sec

20 pulses/sec

10 pulses/sec

40 pulses/sec

33 pulses/sec

20 pulses/sec

10 pulses/sec

40 pulses/sec

33 pulses/sec

20 pulses/sec

10 pulses/sec

390 ms

650 ms

390 ms

650 ms

1800 Hz

1900 Hz

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Location: 28

CS Protocols:

When selecting a contact ID & SIA format, all the reporting codes will be automatically

applied to the locations of the reporting codes.

To change a code, enter a new code (according to the type of event – see page 30) to the

corresponding location.

When selecting the Pulsed Protocol the default for all the reported codes will be “00” and

any other code should be entered manually

To remove a particular reporting code from any of the 3 Protocols enter “00” into the

corresponding location.

Important: Choose the code format only after defining the zone parameters. Changing a

zone type after selecting the code format WILL NOT change the zone’s reporting code and

a faulty report will be sent to the central station.

Digit

Format Name

Pulsed Protocol

Contact ID

SIA

Interdigit Time

Data Frequency

390 ms

1800 Hz

**03

(Ver. 1.3)

Ademco 4/2 Express

Upload/Download Rings: Location 29

Location 29 sets the number of rings that the ORBIT-6 will wait before automatically

answering an incoming call. If such a call was initiated by the alarm company’s

Upload/Download software, a process begins which allows a Remote Programming

session to take place.

Location: 29

Number of Rings

Default: 12

Choose a number of rings greater than that which the customer will normally wait to answer

Number

of Rings

an incoming call enter two digits; (between 00-15 rings)

Note: if an Answering Machine is in use and so programmed

(see Location 26 / 2^ndDigit), entries made in this location will be ignored

SYSTEM CONTROLS: LOCATION 30

Location 30 allows you to specify some additional parameters, which determine how the

ORBIT-6 will operate. The location contains two digits.

First digit: determine the number (or letter) corresponding to the choices involving

Quick Arm / Quick Bypass / UO Extender / Loudspeaker / Bell-Siren

· Second digit: determine the number (or letter) corresponding to the use of

Silent Panic / Bell Squawk on Arming / 3 Minute Bypass

Comments on System Controls (Location 30: 1^stDigit)

Quick Arm

Quick Bypass

UO Extender

select UO Extender select Loudspeaker if the

if the Utility Output external sounder(s) is NOT

Loudspeaker/Bell-Siren

Quick Arm

eliminates the

Eliminates the

need to enter a

need for entering

a User Code when

arming to the STAY

or AWAY modes.

simply pressing

[STAY] or [ARM] will

arm the system to

the respective mode

User Code when Expansion Module is equipped with a built-in sound

bypassing a zone. installed

driver; doing so causes the

ORBIT-6 to produce an

oscillating frequency for the

device, select Bell/Siren if the

external sounder(s) is a bell or

a buzzer or equipped with a

built-in electronic sound driver;.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Comments on System Controls (Location 30: 2^ndDigit)

Silent Panic

Bell Squawk on Arming

3 Minute Bypass Enabled

If “NO”, the panic alarm If selected, Bell Squawk on If selected, 3-Minute Bypass Enabled

will be AUDIBLE at the Arming will produce a brief bypasses all zones automatically for 3

External Sounder and

visual on the keypad.

confirmation “chirp” from the minutes when power is restored to an

system’s external sounder(s) “unpowered” system–to prevent

If “YES”, the panic alarm once the system is armed

potential false alarms by allowing time

for the stabilization of motion and/or

smoke detectors

will be INAUDIBLE at

the External Sounder

and invisable on the

keypad.

and the Exit Delay expires

Location: 30

System Controls: (1^stDigit):

1^stDigit

Loudspeaker/Bell-Siren UO Extender

Quick Bypass

Quick Arm

Bell-Siren

Loudspeaker

Yes

Loudspeaker

Yes

(default)

Loudspeaker

Yes

Location: 30

2^ndDigit

System Controls: (2^ndDigit):

CZ Installation

Bell Squawk on

3 Minute Bypass

Silent Panic

Arm

**4

**5

**6

**7

Disabled

Enabled

Yes

Enabled

Yes

(default)

**C

**D

**E

**F

Enabled

Yes

** New in Ver. 1.3

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

System Controls:

1^STDigit

System Controls:

2^ndDigit

PERIODIC TEST TIME: LOCATION 31

If desired, the ORBIT-6 can send a daily test transmission to the Central Station to verify the

operation of the unit’s Digital Communicator.

Location: 31

Periodic Test Time

Default: 0000

Sets a fixed, daily time for sending an ORBIT-6 test transmission to the Central Station. The

chosen time is expressed in 24-Hour format (following examples):

8:30 AM=0830

If desired, disable the test transmission capability by

accepting (or entering) the default (0000)

11:15AM=1115

4:30 PM=1630

Periodic

Test Time

Note: Failure to set the systems’ time clock, will prevent the

code from being sent to the Central Station.

COMMUNICATOR REPORTING CODES: LOCATIONS 32 THROUGH 86

To program the codes that will be transmitted by the ORBIT-6 to the Central Station.

To prevent the corresponding event from being reported, use a “double-zero” (00, the default) in

the location.

Reporting Codes for Alarm Events:

Location

Description

Digits Default Report Code

Zone 1 Alarm Reporting code

Zone 2 Alarm Reporting code

Zone 3 Alarm Reporting code

Zone 4 Alarm Reporting code

Zone 5 Alarm Reporting code

Zone 6 Alarm Reporting code

Zone 7 Alarm Reporting code

Zone 8 Alarm Reporting code

Keypad Fire Alarms Reporting code

Keypad Panic Reporting code

Keypad Special Emergency Reporting code

Notes on Alarm Restorals

An ORBIT-6 Restoral Report informs the Central Station that the external sounder’s operation,

initially triggered by the respective alarm condition, has either “timed out” or been silenced by the

act of system disarming. Be sure to check with Central Station personnel if restorals are

permitted and, if so, what codes are required.

Restoral Codes

Location

Description

Digits Default Report Code

Zone 1 Restoral Code

Zone 2 Restoral Code

Zone 3 Restoral Code

Zone 4 Restoral Code

Zone 5 Restoral Code

Zone 6 Restoral Code

Zone 7 Restoral Code

Zone 8 Restoral Code

Keypad Fire Restoral Code

Keypad panic Restoral Code

Keypad Special Emergency Restoral Code

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Other Reporting Codes

Location

Description

Digits Default Report Code

Daily test Report Code sent everyday at the time

specified in Location 24

User 0 arm (the “Master” Code, “Quick Arm” OR

“Keyswitch” Arm)

User 1 arm Reporting code

User 2 arm Reporting code

User 3 arm Reporting code

User 4 arm Reporting code

User 5 arm Reporting code

User 6 arm Reporting code

User 7 arm Reporting code

User 8 arm Reporting code

User 9 arm Reporting code

Forced arm (when the system is armed with a

bypassed zone) Reporting code

Stay arm when the system is armed to the Stay

(At Home) mode) Reporting code

User 0, disarm Reporting code (key switch disarm)

User 1 disarm Reporting code

User 2 disarm Reporting code

User 3 disarm Reporting code

User 4 disarm Reporting code

User 5 disarm Reporting code

User 6 disarm Reporting code

User 7 disarm Reporting code

User 8 disarm Reporting code

User 9 disarm Reporting code

Duress Disarm

Trouble Reports and Restorals

Location Description

Digits Default Report Code

**86

Low Battery Reporting code

loss of AC Power (for at least 15 min) Reporting code

Fire zone trouble Reporting code

Bell Loop Interrupted Reporting Code

Low Battery restore Reporting code

Loss of AC Power restore Reporting code

Fire zone trouble Restore Reporting code

Bell Loop Restored Reporting Code

Auto Arm

**New in Version 1.3

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Customer ________________________

Address _________________________

City ____________ State _____Zip ___

Date of Installation: ________________

Installer(s): ______________________

Comments: ______________________

ORBIT-6 Installer Programming Worksheet

Customer Phone No: (

) ___________________

Central Station Account No:___________________

Comments:________________________________

Location Description

Entry

Location Description

Entry

Default Disable

MS LOCK

Phone No. CS 1

Phone No. CS 2

UD Call back

CS Account No.

Access Code

Remote ID Code

Installer Code 1

Installer Code 2

Master Code

**86

Rst Code Zone 2

Rst Code Zone 3

Rst Code Zone 4

Rst Code Zone 5

Rst Code Zone 6

Rst Code Zone 7

Rst Code Zone 8

Rst Kpd Fire

Rst Kpd Panic

Rst Kpd SP

Rpt Code per Test

User 0 Arm

User 1 Arm

User 2 Arm

User 3 Arm

User 4 Arm

User 5 Arm

User 6 Arm

User 7 Arm

User 8 Arm

See below

Exit Delay

Entry Delay

Bell Cutoff Time

Zone 1 Settings

Zone 2 Settings

Zone 3 Settings

Zone 4 Settings

Zone 5 Settings

Zone 6 Settings

Zone 7 Settings

Zone 8 Settings

Utility Output 1

Utility Output 2

Utility Output 3

Utility Output 4

Dialer Controls

CS Protocols 1

CS Protocols 2

U/D Rings

System Controls

Periodic Time Set

Zone 1 Alarm

Zone 2 Alarm

Zone 3 Alarm

Zone 4 Alarm

Zone 5 Alarm

Zone 6 Alarm

Zone 7 Alarm

Zone 8 Alarm

Kpd Fire Alarm

Kpd Panic Alarm

Kpd SP Alarm

Rst Code Zone 1

User 9 Arm

Forced Arm

Stay Arm

User 0 disarm

User 1 disarm

User 2 disarm

User 3 disarm

User 4 disarm

User 5 disarm

User 6 disarm

User 7 disarm

User 8 disarm

User 9 disarm

Duress Disarm

Rpt Code Low Bat

Rpt Code AC Loss

Rpt Code Fire Tbl.

Rpt Code Bell Loop

Rst Code Low Bat

Rst Code AC Loss

Rst Code Fire Tbl.

Rst Code Bell Loop

Auto Arm

**New in Ver. 1.3

Phone 1

Phone 2

UD Call back

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTACT ID & SIA REPORT CODES FOR ORBIT 6

Event Reporting Contact ID

SIA

Program

Zones Alarms/Disarm

Program

Code

Digit

Exit/Entry Alarm

Exit/Entry Restore

Burglary Zone Alarm

Burglary Zone Restore

24 Hour Zone Alarm

134

130

133

137

111

112

113

114

116

117

24 Hour Zone Restore

Tamper Zone Alarm

Tamper Zone Restore

Smoke Zone Alarm/Restore

Combustion Zone Alarm/Restore

Water Flow Zone Alarm/Restore

Heat Zone Alarm

Heat Zone Restore

Duct Zone Alarm/Restore

Flame Zone Alarm/Restore

Panic Zone Alarm

Restore

Silent Alarm

Audible Alarm

122

123

131

132

135

136

140

144

150

151

152

153

154

Code

Perimeter Zone Alarm/Restore

Interior Zone Alarm/Restore

Day/Night Zone Alarm/Restore

Outdoor Zone Alarm/Restore

General Alarm/Restore

Sensor Tamper Alarm/Restore

24 Hour Non Burg Alarm/Restore

Gas Detected Alarm

Gas Detected Restore

Refrigeration Zone Alarm/Restore

Loss of Heat Alarm/Restore

Water Leakage Alarm

Zones Alarms/Disarm

Program

Digit

Program

Digit

Code

Water Leakage Restore

Foil Break Alarm/Restore

Low Battled Gas level Alarm/Restore

High Temperature Alarm/Restore

154

155

157

158

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Event Reporting

Contact ID

SIA

Program

Zones Alarms/Disarm

Program

Code

Digit

Low Temperature Alarm/Restore

Los of Air Flow

159

161

Special

Special Emergency Key Alarm

Special Emergency Key Restore

Fire Zone Alarm

Fire Zone Restore

Fire Key Alarm

Fire Key Restore

Panic Key Alarm

Panic Key Restore

Duress Alarm

Duress Restore

100

110

115

120

121

Troubles

AC Trouble

AC Restore

301

302

321

373

Low Battery Trouble

Low Battery Restore

Main Bell Trouble

Main Bell Restore

Fire Trouble

Fire Restore

O/C Access

User Arm

User Disarm

Quick Arm/Disarm - User 0

Forced Arm

Periodic Test

Auto Alarm

401

408

574

602

403

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

ORBIT-6 Wiring Diagram

FIGURE 1A

TR1

SIG

UR1

DEFAULT

TIP

RING

TELEPHONE

SET

ECL

AUX

RED

CLK DAT

YEL GRN

TMP

COM

BLK

BELL/LS

Z3 COM Z4

AUX

TO TELEPHONE

LINE

RECHARGEABLE

BATTERY

12V 4ah typical

TO ZONES CONTACTS

TO KEYPAD(S)

16.5 Vac

30 VA

12VDC 250 mA

POWER SUPPLY

PROGRAMMABLE

OPEN COLLECTOR

MAX 70mA OR

TYPICAL BURGLARY

ZONE WIRINGS

(TWO DETECTIONS FOR EACH ZONE)

BELL

12VDC

750 mA MAX

TO UO EXPANDER

LOUD

SPEAKER

TYPICAL FIRE

ZONE WIRINGS

(4 WIRE SMOKE DETECTIONS )

12VDC

SUPERVISING

RELAY

N/O

CONTACTS

N/C

CONTACTS

AUX

Z5 COM UO

+IN

+OUT

-IN

ALARM

CONTACT

END OF LINE RESISTORS

2,2 K 1/4 WATT

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

ORBIT-6 Wiring Diagram

FIGURE 1B

TR1

SIG

UR1

DEFAULT

TIP

RING

TELEPHONE

SET

CLK DAT

YEL GRN

AUX COM

RED BLK

TMP

BELL/LS

Z1 C O M Z2

Z3 COM Z4 Z5 C O M

AUX

ECL

TO TELEPHONE

LINE

RECHARGEABLE

BATTERY

12V 4ah typical

TO ZONES CONTACTS

TO KEYPAD(S)

16.5 Vac

30 VA

TYPICAL BURGLARY

ZONE WIRINGS

BELL

)

(TWO DETECTIONS FOR EACH ZONE

12VDC

750 mA

MAX

LOUD

SPEAKER

N/O

CONTACTS

N/C

ONTACTS

12VDC 250 mA

POWER SUPPLY

TYPICAL FIRE

ZONE WIRINGS

(4 WIRE SMOKE DETECTIONS )

12VDC

SUPERVISING

RELAY

+IN

-IN

+OUT

-OUT

ALARM

CONTACT

ECL

YEL

GND

BLK

DAT

GRN

Uo2 Uo3 Uo4

Uo1

END OF LINE RESISTORS

2,2 K 1/4 WATT

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Zone Extension

Power LED

Arm LED

Z7 COM

Ready LED

Fire LED

Zone 1

Zone 2

Zone 3

Backlit LEDS

Zone 4

Zone 5

Zone 6/Tmp

Zone 7

Zone 8

AUX GND CLK DAT

WHT RED BLK YEL GRN

(Keypad Buzzer)

Panic Button

the

FIGURE 1C

8-ZONE KEYPAD BOARD

Control

Panel

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

ROKONET LIMITED WARRANTY

Rokonet Electronics, Ltd. and its subsidiaries and affiliates ("Seller") warrants

its products to be free from defects in materials and workmanship under

normal use for 18 months from the date of production. Because Seller does

not install or connect the product and because the product may be used in

conjunction with products not manufactured by the Seller, Seller can not

guarantee the performance of the security system which uses this product.

Sellers obligation and liability under this warranty is expressly limited to

repairing and replacing, at Sellers option, within a reasonable time after the

date of delivery, any product not meeting the specifications. Seller makes no

other warranty, expressed or implied, and makes no warranty of

merchantability or of fitness for any particular purpose.

In no case shall seller be liable for any consequential or incidental damages

for breach of this or any other warranty, expressed or implied, or upon any

other basis of liability whatsoever.

Sellers obligation under this warranty shall not include any transportation

charges or costs of installation or any liability for direct, indirect, or

consequential damages or delay.

Seller does not represent that its product may not be compromised or

circumvented; that the product will prevent any persona; injury or property

loss by burglary, robbery, fire or otherwise; or that the product will in all

cases provide adequate warning or protection. Buyer understands that a

properly installed and maintained alarm may only reduce the risk of burglary,

robbery or fire without warning, but is not insurance or a guaranty that such

will not occur or that there will be no personal injury or property loss as a

result.

Consequently seller shall have no liability for any personal injury, property

damage or loss based on a claim that the product fails to give warning.

However, if seller is held liable, whether directly or indirectly, for any loss or

damage arising from under this limited warranty or otherwise, regardless of

cause or origin, sellers maximum liability shall not exceed the purchase price

of the product, which shall be complete and exclusive remedy against seller.

No employee or representative of Seller is authorized to change this

warranty in any way or grant any other warranty.

WARNING: This product should be tested at least once a week.

Installer Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Mr Coffee Coffeemaker BL4 User Manual
MTD Snow Blower Attachment 190 822 User Manual
Nady Systems Stereo System MM242 User Manual
NEC Car Video System LCD1860NX User Manual
Omnimount TV Video Accessories MORELLO50 User Manual
Opticon Barcode Reader CRD 9723 User Manual
Oregon Scientific Games Clone Trooper Junior Laptop User Manual
Palsonic CRT Television 6159 User Manual
Panasonic Cell Phone EB GD50 User Manual
Panasonic Telephone DBS576 User Manual