14-1121.fm Page 1 Thursday, July 1, 1999 2:42 PM
Cat. No. 14-1121
OWNER’S MANUAL
Please read before using this equipment.
CTR-115
Voice-Activated
Cassette Tape Recorder
with Pop-Up Microphone
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 3 Thursday, July 1, 1999 2:42 PM
Mic Sensitivity Switch — lets you select low, medium, or high
microphone sensitivity for recording.
Record/Battery Indicator — lights when you are recording.
When you are not, it indicates the battery’s condition.
Built-In Speaker — lets you listen to your recordings.
Automatic Level Control — automatically sets the right re-
cording level; no need to adjust the volume while recording.
Three Power Sources — let you power your recorder from in-
ternal batteries, or from a vehicle’s cigarette-lighter socket or
standard AC power (using the appropriate optional adapter).
We recommend you record the CTR-115’s serial number here.
The number is inside the cassette compartment.
Serial Number: ___________________________
3
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 4 Thursday, July 1, 1999 2:42 PM
CONTENTS
Preparation ............................................................................ 5
Before You Begin ............................................................... 5
Powering the CTR-115 ...................................................... 5
Installing Batteries ....................................................... 6
Using AC Power .......................................................... 7
Using Vehicle Battery Power ....................................... 8
Connecting the Earphone ................................................ 10
Listening Safely ......................................................... 10
Traffic Safety .............................................................. 11
Playing a Cassette Tape ..................................................... 12
Using the Tape Counter ................................................... 16
Recording ............................................................................. 17
Using the Built-In Microphone ......................................... 17
Vox Recording ................................................................. 18
Manual Recording ........................................................... 20
Cue Marker ...................................................................... 21
Using an External Microphone ........................................ 21
Recording from External Sources .................................... 22
Tape Tips .............................................................................. 23
Erasing a Recording ........................................................ 23
Preventing Accidental Erasure ........................................ 23
Restoring Tape Tension and Sound Quality .................... 24
Care and Maintenance ........................................................ 25
Cleaning the Tape-Handling Parts ................................... 25
Specifications ...................................................................... 27
4
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 5 Thursday, July 1, 1999 2:42 PM
PREPARATION
BEFORE YOU BEGIN
To protect the record/playback head during shipment, a protec-
tive sleeve is positioned around the head. Gently pull open the
cassette compartment door and remove the sleeve before you
use the cassette recorder.
POWERING THE CTR-115
You can operate your CTR-115 from any of these power sourc-
es:
• two AA batteries (not supplied)
• standard household AC power (using an optional AC
adapter)
• a 12-volt vehicle battery (using an optional DC adapter)
Note:
Using an adapter automatically disconnects the internal
batteries.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 6 Thursday, July 1, 1999 2:42 PM
Installing Batteries
You can power the CTR-115 with two AA batteries. We recom-
mend alkaline batteries, such as RadioShack Cat. No. 23-552.
Cautions:
• Use only fresh batteries of the required size and recom-
mended type.
• Do not mix old and new batteries or different types of bat-
teries.
1. Press down on the battery com-
partment cover and slide it off in
the direction of the arrow.
2. Put the batteries into the com-
partment as indicated by the
polarity symbols (+ and –)
marked beside it.
3. Replace the cover.
If the REC/BATT indicator does not
light (or lights dimly) when you press
PLAY , FAST-F/CUE
or REWIND/
REC/BATT
REV , replace the batteries.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 7 Thursday, July 1, 1999 2:42 PM
Cautions:
• Always remove old or weak batteries. Batteries can leak
chemicals that can destroy electronic parts.
• Dispose of old batteries promptly and properly. Do not burn
or bury them.
Using AC Power
To power the CTR-115 from an AC outlet, you need an AC
adapter, such as RadioShack Cat. No. 273-1654.
Cautions:
• The recommended adapter supplies 3 volts DC power and
delivers at least 300 milliamps. The adapter’s center tip
must be set to positive, and its plug must properly fit the
CTR-115’s DC IN 3V jack. Using an adapter that does not
meet these specifications could damage the CTR-115 or
the adapter.
• Be sure you connect the adapter to the CTR-115 before
you plug it into the AC outlet, and that you unplug the
adapter from the AC outlet before you unplug it from the
CTR-115.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 8 Thursday, July 1, 1999 2:42 PM
Follow these steps to power the CTR-115 with an AC adapter.
1. Set the adapter’s voltage switch to 3V.
2. Insert the adapter’s 2.35 mm outer diameter/0.7 mm inner
diameter barrel plug into the adapter’s cord, with the tip set
to positive.
3. Insert the barrel plug into the CTR-115’s DC IN 3V jack.
4. Plug the adapter into a standard AC outlet.
Using Vehicle Battery Power
You can operate the CTR-115 from your vehicle’s battery with a
DC adapter (not supplied), such as Cat. No. 273-1810.
Cautions:
• The recommended adapters supply 3 volts DC power and
deliver at least 300 milliamps. The adapter’s center tip
must be set to positive, and its plug must properly fit the
CTR-115’s DC IN 3V jack. Using an adapter that does not
meet these specifications could damage the CTR-115 or
the adapter.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 9 Thursday, July 1, 1999 2:42 PM
• Be sure you plug the adapter into the CTR-115 before you
plug it into the cigarette-lighter socket, and that you unplug
the adapter from the cigarette-lighter socket before you
unplug it from the CTR-115.
Follow these steps to power the CTR-115 from your vehicle’s
cigarette-lighter socket.
1. Set the adapter’s voltage switch to 3 volts.
2. Insert the adapter’s 2.35 mm outer diameter/0.7 mm inner
diameter barrel plug into the adapter’s cord, with the tip set
to positive.
3. Insert the barrel plug into the CTR-115’s DC IN 3V jack.
4. Plug the other end of the adapter into the vehicle’s ciga-
rette-lighter socket.
Note: If the CTR-115 does not operate properly when connect-
ed to a cigarette-lighter socket, unplug the adapter and clean
any ashes and other debris from the socket.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 10 Thursday, July 1, 1999 2:42 PM
CONNECTING THE EARPHONE
You can use the supplied earphone to listen privately to record-
ed sound or to monitor recording. You can also connect an ex-
ternal or pillow-type speaker (not supplied) to this jack.
Note:
Your local RadioShack store sells a wide variety of
speakers.
Insert the earphone or speaker’s 1/8-inch (3.5-mm) plug into the
EAR jack. This automatically disconnects the internal speaker.
EAR
Listening Safely
To protect your hearing, follow these guidelines when you use
the earphone.
• Do not listen at extremely high volume levels. Extended
high-volume listening can lead to permanent hearing loss.
• Set the volume to its lowest level before you begin listen-
ing. After you put on the earphone, adjust the volume to a
comfortable listening level.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 11 Thursday, July 1, 1999 2:42 PM
• Do not increase the volume once you have established a
comfortable listening level. Over time, your ears adapt to
the volume level, so a volume level that does not cause
discomfort might still damage your hearing.
Traffic Safety
Do not wear the earphone while operating a motor vehicle or
riding a bicycle. This can create a traffic hazard and could be il-
legal in some areas.
Even though some earphones let you hear some outside
sounds when listening at normal volume levels, they still can
present a traffic hazard.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 12 Thursday, July 1, 1999 2:42 PM
PLAYING A CASSETTE TAPE
1. Gently pull open the cassette
compartment door.
2. Use your finger or a pencil to
turn the cassette’s hub and take
up any slack in the tape. Do not
touch the tape.
3. Load a cassette into the door’s
guides so the cassette’s open
edge is out and the side you
want to play faces the compart-
ment’s window, then close the
door.
TAPE SPEED
SLOW NORMAL FAST
, or to suit your
4. Set
to
,
listening preference.
NORMAL
SLOW
FAST
TAPE SPEED
12
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 13 Thursday, July 1, 1999 2:42 PM
Note: This switch’s setting has no effect when recording
(see “Recording” on Page 17).
5. Rotate VOLUME/VOX SENS counterclockwise to its lowest
setting.
6. Press PLAY . The tape begins to play.
PLAY
7. Adjust VOLUME/VOX SENS to a comfortable listening level.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 14 Thursday, July 1, 1999 2:42 PM
8. Set VOX/TONE to HIGH to emphasize treble sounds, or to
LOW to reduce them. With metal/High-Bias tape, use LOW
for a more natural sound.
LOW HIGH
OUT
IN
VOX/ TONE
9. The CTR-115 automatically stops at the end of the tape.
Or, press STOP to stop the tape.
STOP
Notes:
• To momentarily stop play, slide PAUSE to ON. Slide PAUSE
to OFF to resume playing.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 15 Thursday, July 1, 1999 2:42 PM
OFF
ON
PAUSE
• To rapidly advance or rewind the tape, press FAST-F/
CUE or REWIND/REV . The button locks down and the
tape continues moving until you press STOP. The TAPE
SPEED setting affects the fast-forward or rewind speed.
FAST-F/CUE REWIND/REV
• The CTR-115 does not automatically stop when it reaches
the end of the tape during fast-forward or rewind. To pre-
vent damage to the tape after it has fully wound to either
end, press STOP to release fast-forward or rewind.
• If you press FAST-F/CUE
or REWIND/REV
while the
tape plays, you hear the tape playing at high speed. This
can help you locate a specific portion of the tape.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 16 Thursday, July 1, 1999 2:42 PM
USING THE TAPE COUNTER
You can use the tape counter to
give you an indication of the tape’s
TAPE COUNTER RESET
0 0 0
position. Before playing
a
tape,
press the tape counter reset button
to set the counter to 000.
When the recorder plays, the numbers advance to show the
amount of tape that has moved past the tape heads since the
tape began moving. When the tape rewinds, the numbers de-
crease.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 17 Thursday, July 1, 1999 2:42 PM
RECORDING
Note:
For the best performance, use only regular length (60- or
90-minute) cassette tapes. We do not recommend long-playing
cassette tapes, such as C-120s, because they are extremely
thin and can tangle easily.
USING THE BUILT-IN MICROPHONE
You can pop up the built-in microphone to direct it to the sound
source, or you can connect an external microphone (see “Using
an External Microphone” on Page 21).
Follow these steps to use the built-in microphone.
MIC POP-UP
1. Slide
in the direc-
tion of the arrow marked under
the microphone.
MIC POP-UP
MIC SENSITIVITY
LOW
,
2. Slide
to
MEDIUM
HIGH
or
, depending on
the sound source you want to
record.
MEDIUM
For normal recording conditions, set the switch to
.
HIGH
. For a strong
If the sound source is weak, slide it to
LOW
sound source, slide it to
.
3. To return the microphone to its original position, gently
press it down until it locks into place.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 18 Thursday, July 1, 1999 2:42 PM
VOX RECORDING
When you select VOX recording, the CTR-115 automatically
begins recording when it receives a sound signal from a voice
or other sound, and automatically stops when the sound stops.
For the best recording quality, place the recorder about 1 foot
from the sound source. Because the microphone is so sensi-
tive, it will also pick up a voice or group of voices (such as an
audience) from several feet away.
1. Gently pull open the cassette
compartment door.
2. Use your finger or a pencil to
turn the cassette’s hub and take
up any tape slack, and advance
the cassette past the leader at
the beginning of the tape.
3. Load a cassette into the door’s guides with the cassette’s
open edge out and the side you want to record on facing
the compartment’s window. Then close the door.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 19 Thursday, July 1, 1999 2:42 PM
4. Set VOX/TONE to IN.
LOW HIGH
OUT
IN
VOX/ TONE
5. Set VOLUME/VOX SENS to the desired setting (0–10) to con-
trol how loud a sound is required to turn on the recording
function.
At 10, a soft sound turns on the recorder. At settings closer
to 0, it takes a louder sound to start recording. Experiment
to find the best setting for VOLUME/VOX SENS in your
recording environment.
Note: Use the supplied earphone when you want to moni-
tor a recording in progress (see “Connecting the Earphone”
on Page 10).
6. Press RECORD. RECORD and PLAY lock down. Record-
ing starts when the microphone receives a loud enough
signal (voice or other sound). It temporarily stops when the
signal ceases.
The ALC (automatic level con-
trol) circuit automatically sets
the recording level and the
REC/BATT
REC/BATT indicator flashes to
show that recording is in
progress.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 20 Thursday, July 1, 1999 2:42 PM
Note: If the audio input is too strong, the indicator lights
steadily.
7. To momentarily stop recording even while the sound con-
tinues, slide PAUSE to ON. Slide PAUSE to OFF to resume
recording.
OFF
ON
PAUSE
Caution: Never try to force down RECORD if you have
removed the erase protection tab (see “Preventing Acci-
dental Erasure” on Page 23). This can damage the record/
play mechanism.
8. Recording stops when the sound stops. Or, press STOP to
stop recording while the sound continues.
MANUAL RECORDING
Manual recording is like VOX recording, except you control
when recording begins and ends. Set VOX/TONE to OUT, then
press RECORD to begin recording. Press STOP to stop record-
ing, or slide PAUSE to ON to temporarily stop recording.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 21 Thursday, July 1, 1999 2:42 PM
CUE MARKER
To mark the beginning of a recording, press CUE MARKER for
about 3 seconds during the recording. This records a brief tone
on the tape. When you press FAST-F/CUE
or REWIND/REV
while the tape plays, you hear the tone when the tape reaches
the point you marked.
USING AN EXTERNAL MICROPHONE
The CTR-115’s built-in microphone works well in most situa-
tions, but you can connect an external microphone (not sup-
1
plied) with a /8-inch (3.5-mm) plug to the recorder’s MIC jack.
This automatically disconnects the built-in microphone.
Note:
Your local RadioShack store sells a variety of micro-
phones.
Set VOX/TONE to IN for VOX recording, or to OUT for manual re-
cording.
If the microphone has an ON/OFF switch for remote control,
connect the microphone to the REM and MIC jacks. Then you
can start and stop recording with the switch on the microphone.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 22 Thursday, July 1, 1999 2:42 PM
RECORDING FROM EXTERNAL
SOURCES
You can record directly from a tuner, a radio, or a TV that has a
1/8-inch (3.5-mm) jack. Use a dubbing patch cord such as Ra-
dioShack Cat. No. 42-2152 to connect the CTR-115’s MIC jack
to the headphone output jack of an external component. Set
VOX/TONE to OUT, then proceed with manual recording.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 23 Thursday, July 1, 1999 2:42 PM
TAPE TIPS
ERASING A RECORDING
If you want to erase an entire cas-
sette or a portion of a recording, in-
sert the supplied erase plug into the
MIC
MIC
VOX/TONE
jack. Then set
to
OUT
and record silence over the
previous recording.
Or, you can quickly erase both sides of a cassette tape using a
bulk tape eraser, available at your local RadioShack store.
PREVENTING ACCIDENTAL ERASURE
Cassettes have two erase-protection tabs — one for each side.
When a tab is in place, you can record on that side.
To prevent accidental erasure of a tape recording, use a screw-
driver to remove one or both of the cassette tape’s erase-pro-
RECORD
tection tabs. This prevents
from being pressed.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 24 Thursday, July 1, 1999 2:42 PM
If you later decide to record on a tape side after you have re-
moved its erase-protection tab, place a piece of strong plastic
tape over that side’s erase-protection hole. Be sure you cover
only the hole originally covered by the erase-protection tab.
A
Caution: Removing the erase-protection tabs does not prevent
a bulk tape eraser from erasing a cassette tape.
RESTORING TAPE TENSION AND
SOUND QUALITY
After you play a cassette tape several times, the tape might be-
come tightly wound on the reels. This can cause playback
sound quality to deteriorate.
To restore the sound quality, fast-forward the tape from the be-
ginning to the end of one side, then completely rewind it. Then
loosen the tape reels by gently tapping each side of the cas-
sette’s outer shell on a flat surface.
Caution: Be careful not to damage the cassette when tapping
it. Do not touch the exposed tape or allow any sharp objects
near the cassette.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 25 Thursday, July 1, 1999 2:42 PM
CARE AND MAINTENANCE
To enjoy your CTR-115 for a long time:
• Keep the CTR-115 dry. If it gets wet, wipe it dry immedi-
ately.
• Use and store the CTR-115 only in normal temperature
environments.
• Handle the CTR-115 gently and carefully. Don’t drop it.
• Keep the CTR-115 away from dust and dirt.
• Wipe the CTR-115 with a damp cloth occasionally to keep it
looking new.
Modifying or tampering with the CTR-115’s internal components
can cause a malfunction and invalidate its warranty. If your
CTR-115 is not performing as it should, take it to your local Ra-
dioShack store for assistance.
CLEANING THE TAPE-HANDLING
PARTS
Dirt, dust, or particles of the tape’s coating can accumulate on
the tape heads and other parts the tape touches. This can
greatly reduce the performance of the cassette recorder. After
every 20 hours of tape player operation, use a cassette deck
cleaning kit (Cat. No. 44-1202) or follow these steps to clean
the tape-handling parts.
1. Remove the batteries and disconnect any other power
source (such as an adapter).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 26 Thursday, July 1, 1999 2:42 PM
2. Lift open the cassette compartment door.
3. Press the protection tab sensor, then press RECORD. The
tape head assembly moves out.
4. Use a cotton swab dipped in tape head cleaner or dena-
tured alcohol to clean the record/playback head, pinch
roller, tape guides, and capstans.
Protection
Tab Sensor
Tape Guides
Capstans
Pinch Roller
Record/Playback Head
Cautions:
• Never touch the front surface of the record/playback head
with any metallic object.
• Do not use a tape demagnetizer on this product because
such demagnetizers can impair operation of the permanent
magnet erasing device.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 27 Thursday, July 1, 1999 2:42 PM
SPECIFICATIONS
Tape System .............................. 2-track, Monophonic Cassette
Tape Speed .......................................... 17/8 ips. (4.75 cm/sec.)
Wow and Flutter ............................................... 0.25% (WRMS)
Signal-to-Noise Ratio (Rec/Play) ..................................... 38 dB
Erase System ............................................................... Magnet
Record System ............................................................ AC Bias
Tape Type Recommended .......................... Normal Bias Type I
Power Requirement:
DC ...................................... Two AA batteries (3 volts DC)
or vehicle’s cigarette-lighter socket
with Cat. No. 273-1810 DC adapter
AC .............. 120 volts with Cat. No. 273-1654 AC adapter
Size (HWD) ..................................... 39/16 × 415/32 × 13/8 Inches
(90.5 × 112 × 34.9 mm)
Weight (without batteries)................................................. 5.6 oz
(158 g)
Included Accessories ....................... Earphone and Erase Plug
Specifications are typical; individual units might vary. Specifica-
tions are subject to change and improvement without notice.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
14-1121.fm Page 28 Thursday, July 1, 1999 2:42 PM
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in material and
workmanship under normal use for ninety (90) days from the date of purchase from Ra-
dioShack company-owned stores and authorized RadioShack franchisees and dealers.
EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES
AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURA-
TION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS
PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO
CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABIL-
ITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY,
INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-
NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDI-
RECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclu-
sion of incidental or consequential damages, so the above limitations or exclusions may
not apply to you.
In the event of a product defect during the warranty period, take the product and the Ra-
dioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack
will, at its option, unless otherwise provided by law: (a) correct the defect by product repair
without charge for parts and labor; (b) replace the product with one of the same or similar
design; or (c) refund the purchase price. All replaced parts and products, and products on
which a refund is made, become the property of RadioShack. New or reconditioned parts
and products may be used in the performance of warranty service. Repaired or replaced
parts and products are warranted for the remainder of the original warranty period. You will
be charged for repair or replacement of the product made after the expiration of the war-
ranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of
God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions,
improper installation or maintenance, alteration, lightning or other incidence of excess volt-
age or current; (b) any repairs other than those provided by a RadioShack Authorized Ser-
vice Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e)
transportation, shipping or insurance costs; or (f) costs of product removal, installation, set-
up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth,
TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
2133-920-0-01
Printed in China
8A8
Download from Www.Somanuals.com. All Manuals Search And Download.
|