Opticon Scanner OPT 6125 User Manual

User’s Manual

OPT-6125 Series

Handheld CCD Scanner

25-ULGPMU01-01

April 2002

Keyboard Wedge Interface

USB Interface

RS232 Interface

8 Olympic Drive

Orangeburg, NY 10962

Tel 845.365.0090

Fax 845.365.1251

www.opticonUSA.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

Series OPT Handheld CCD Scanner

Table of Contents

PART I CCD Scanning

Part III Bar Code Menu Functions

Section A Programming the Scanner……………..12

General Information ...........................................4

Unpacking

Factory Technical Support

Section B Symbology Selections ..................... 13

Enabling only a single symbology...................... 13

Enabling an addition symbology........................ 13

Setting Options for UPC-A/E ............................. 17

Setting Options for EAN-13 and -8 .................... 20

Code 39 Settings ............................................. 22

Codabar Settings ............................................. 24

2 of 5 Settings................................................. 27

MSI/Plessey Setting ......................................... 29

Code 128 Setting............................................. 30

IATA Settings .................................................. 31

Part II Installation and SetUp

A. Installation –Wedge Interface ……………5

Reset all Defaults …………………………………………….6

Computer Type Selection … ............................... 6

InterCharacter Delay ..........................................7

Section C: Universal Selections

B. Installation – RS232 Interface................ 8

RS-232C Communication Parameter s ..................9

Baud Rate..........................................................9

Data Bits / Stop Bits / Parity..............................10

Case Conversion.............................................. 33

Prefix Options.................................................. 34

Suffix Options.................................................. 36

Direct Input - Keyboard Keys............................ 38

Direct Input - Characters ................................ 44

Direct Input - Control Characters ...................... 49

Read Mode Settings......................................... 52

Trigger Settings............................................... 53

Beeper Options................................................ 57

Good Read Indicator (LED)............................... 59

C. Installation – USB Interface...................11

_________________________________________

NOTICE

Opticon has taken every step to ensure that the

information included in this manual is accurate,

however we reserve the right to change any

specification at any time without prior notice.

_________________________________________

Page 3

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

Series OPT Handheld CCD Scanner

Part I

General Information

The OPT-6125 Series CCD Scanners utilize state-of-the-art imaging technology similar to that found in digital cameras,

facsimile machines and video camcorders. The scanner images the bar code label, then converts the digital signals into data

the host computer can understand. By capturing the bar code image all at once, the scanner provides fast, highly accurate

reading.

Miniature surface mount electronics make up the CCD scanner's solid state construction. CCD scanners have no moving

mechanical parts and provide years of trouble-free operation.

This manual contains information on setting-up the scanner as well as programming various parameters of the scanner.

The OPT6125 scanner is available in several different interface configurations:

Keyboard Wedge Interface

RS232 Serial Interface

USB Interface

There is a specific section of this manual for installing each type of interface. Be sure you are using the section of the

manual that pertains to interface you are using.

Unpacking

Remove the scanner from its packaging and inspect it for damage. If the scanner was damaged in transit, call the dealer or

distributor from whom you purchased it. If you purchased it directly from Opticon, call Opticon Customer Service Dept. at

800-636-0090.

Factory Technical Support

If you have any questions or need assistance with programming your scanner call Opticon Technical Support at 800-636-

0090 please have the unit model number and several bar code labels readily at hand. The model number is located near the

connector end of the cable.

If the scanner must be returned, please contact Opticon to obtain an RMA (Return Merchandise Authorization) number prior

to returning the product. The Customer Service Dept. may be reached at 800-636-0090.

NOTE: Returned merchandise will not be accepted without a RMA number indicated clearly on the outside of the carton.

Page 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

Series OPT Handheld CCD Scanner

Part II Installation and SetUp

This section of the manual contains information on the physical installation of the scanner as well as certain programming options.

There is a separate section for each type of interface. Check to see which type of interface your scanner has and turn to that

section for information on installing the scanner

A.) Installation – Keyboard Wedge Interface

A "Y" connection cable is required for installation. The scanner is installed or "wedged" between the keyboard and the computer..

Your “Y” cable should have connectors for both a PS2 and AT type installation. The "Y" cable connects both the scanner and the

keyboard to the computer.

The scanner must match the type of computer being used. The default setting is for an IBM AT type computer. If this type does

not match the host computer, refer to the “Computer Type Selection” in the programming section that follows. If the connector

does not match the host compute remove the short cable section, reverse it and insert it in the other connector

Page 5

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

Series OPT Handheld CCD Scanner

Reset All Defaults – Keyboad Wedge Interface

Our scanners are shipped with factory default settings that represent the settings most commonly used by our customers. In most

applications, the scanner will work right out of the box without any need for additional programming. At any time you can return

the scanner to the factory default settings by scanning the “Reset all Defaults” programming bar code below.

NOTE: (

) A pointing finger indicates default settings throughout the following menus.

Start

Program Menu

-[[-

XT Wedge

-VB-

AT Wedge

-VC-

PS2 wedge

-VD-

End

Program Menu

-[[-

Computer Type Selection (for Keyboard Wedge only)

The Keyboard Wedge interface scanner is designed to operate with an IBM personal computers and compatibles along with a

Macintosh PC's. Select the host computer type from the menu below.

NOTE: If the scanner has not been set to the correct host computer, the scanner will display random characters on the screen after

reading a bar code label.

Start

Program

-[[-

-L1-

-L3-

-L!-

-L5-

-[[-

IBM PC/XT

IBM AT &

compatibles

HP Vectra

Macintosh

End

Program

Page 6

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

Series OPT Handheld CCD Scanner

Intercharacter Delay for Keyboard Wedge interface

The scanner may send data faster than the computer or application program can accept. This is called "keyboard buffer overrun".

If data appears to be missing, random read errors occur or the scanner locks up and will not scan, experiment with the various

keyboard timing options listed in the menu to follow.

Start Program

-[[-

No Delay

-MB-

Delay = 1

-MB-

Delay = 2

-MD-

Delay = 3

-ME-

Delay = 4

-MF-

Delay = 5

-MG-

Delay = 6

-MH-

Delay = 7

-MI-

Delay = 8

-MJ-

Delay = 9

-MK-

Delay = 10

-ML-

End Program

-[[-

Page 7

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

Series OPT Handheld CCD Scanner

B.) Installation – RS232 Interface

The RS-232 scanner cable is terminated in with a DB9 female connector. An external power supply (+5V DC) may be necessary.

There is a power supply jack on the RS-232 connector.

Installation is as follows:

1. Plug the scanner into an RS232 serial port (such as COM1) of the host PC. If external power is required, insert external power

plug into the jack on the RS-232 connector.

2. Connect the power supply into an electrical outlet (110 V AC)

3. Turn on the power to the host computer. Make sure the communication parameters of the computer match those of the

scanner. The default communications settings are: 9600 baud, 8 data bits, 1 stop bit, no parity, no handshaking

4. Be sure the PC is in a program (such as WordPad) that will accept input from the serial port.

Reset All Defaults – RS232

Our scanners are shipped with factory default settings that represent the settings most commonly used by our customers. In most

applications, the scanner will work right out of the box without any need for additional programming. At any time you can return

the scanner to the factory default settings by scanning the “Reset all Defaults” programming bar code below.

Start

Program Menu

-[[-

RS232

-V3-

End

Program Menu

-[[-

Page 8

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

Series OPT Handheld CCD Scanner

RS-232C Communication Parameters

Handshaking Protocol

Start

Program

-[[-

-Q1-

None

RTS/CTS

ACK/NAK

Xon/Xoff

HP04

+IQ15+

-Q!-

-[H-

Flow

Control

Time

-J1-

Unlimited

Flow

Control:

100ms

-J2-

-J3-

-J!-

Flow

Control:

200ms

Flow

Control:

400ms

Baud Rate

19200

9600

4800

2400

1200

600

-L8-

-L7-

-L6-

-L5-

-L!-

-L3-

Page 9

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

Series OPT Handheld CCD Scanner

Data Bits / Stop Bits / Parity

7 Data Bits

-M1-

-M2-

-M6-

-M7-

-M!-

-M5-

-M3-

,ZZ,

8 Data Bits

1 Stop Bit

2 Stop Bits

Even

Parity

Odd

Parity

Mark

No Parity

End

Program

Page 10

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

C.) Installation – USB Interface

Plug the scanner into the USB connector on your host computer. PC must be running Windows 98 or higher or

iMac Rev A or higher. The computer will sense the presence of the scanner and load any required software drivers

automatically.

Reset All Defaults - USB Interface

Our scanners are shipped with factory default settings that represent the settings most commonly used by our

customers. In most applications, the scanner will work right out of the box without any need for additional

programming. At any time you can return the scanner to the factory default settings by scanning the “Reset all

Defaults” programming bar code below.

Start

Program

-[[-

-TV-

-[[-

USB

End

Program Menu

Page 11

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Part III

Bar Code Menu Functions

Section A Programming the Scanner

This manual contains information that allows you to easily change certain programmable parameters of the scanner.

The scanner is ready to use - no additional programming is required in most situations. The scanner has been

programmed at the factory with the most common settings. These factory default settings are ideal for most

situations.

A specific parameter is set or changed by scanning one or more of the special programming bar codes found on the

following pages. For each parameter, you can choose from a menu of options. When you scan the special bar code

for a specific menu option, the scanner retains the changes you have made even if you disconnect the scanner or t-

urn off the power.

Step-by-Step

Programming is easy. Simply:

1. Scan the bar code for "Start/End Program Menu" (ZZ). The scanner will beep continuously to indicate that it

is ready to be programmed. When the scanner is in Programming Mode, it cannot read normal bar code. It can

only read the special bar codes found on the following pages.

2. Select desired parameter from menu and scan the bar code. The scanner will beep once and the green light will

flash, indicating the desired parameter has been scanned. The scanner will continue to beep continuously while

in Programming Mode.

3. Scan "Start/End Program Menu" (ZZ). The scanner will stop beeping, indicating that it is back in normal

scanning mode. The changes made while in Programming Mode are now saved in the scanner's memory.

When the scanner is in Programming Mode, more than one parameter at a time can be changed. Until some

proficiency at programming is achieved, it is highly recommended that users only change only one parameter at a

time and test the change before proceeding to program any additional changes. It is also recommended that users

keep a record of the changes made to the scanner.

What If I Make A Mistake?

Scanning the "Reset All Defaults" bar code for your type of interface will return the scanner to all factory default

settings (including any changes made during previous programming sessions).

NOTE: (

) A pointing finger indicates scanner default settings throughout the following menus.

Page 12

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Symbology Selection

Start/End

Program

-[[-

-B1-

-B3-

-B!-

-B5-

-B6-

-B7-

-B8-

-B:-

-BC-

-K1-

-K2-

Read all codes

Code 39

only

Codabar

only

IATA only

Code 93

only

Code 128

only

MSI/Plessey

only

Telepen

only

Matrix 2of5

only

All UPC and

EAN only

UPC

only

CONTINUED ON NEXT PAGE...

Page 13

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Symbology Selection (continued)

Start/End

Program

-[[-

-K3-

-K!-

-K5-

-K6-

-K7-

-K8-

-K9-

-KE-

UPC+2

only

UPC+5

only

EAN

only

EAN+2

only

EAN+5

only

Industrial

2of5

only

Interleaved

2of5

only

Trioptics

only

These options do not influence the reading of the menu labels. The required bar code types can be selected by

enabling a single readable code only and enabling a single readable code only and enabling readable codes. It is

strongly recommended that only the required codes be selected.

Page 14

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Symbology Additions

If scanner will not be used to read all symbologies (default setting), speed operation by using this menu to add only

the specific symbologies being used (add only the symbologies that are required).

Start/End

Program

-[[-

Disable all

-C1-

Enable

Code 39

-C3-

Enable

Codabar

-C!-

Enable

IATA

-C5-

Enable

Code 93

-C6-

Enable

Code 128

-C7-

Enable

MSI/Plessey

-C8-

Enable

Telepen

-C:-

Enable

Trioptics

-K[-

Enable

UPC

-S2-

Enable

UPC+2

-S3-

Enable

UPC+5

-S!-

CONTINUED ON NEXT PAGE...

Page 15

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Symbology Additions (continued)

Start/End

Program

-[[-

-S5-

-S6-

-S7-

-S8-

-S9-

Enable

EAN

Enable

EAN+2

Enable

EAN+5

Enable

Industrial

2of5

Enable

Interleaved

2of5

Page 16

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Setting the Number of

Characters to be Scanned

Start/End

Program

-[[-

-I1-

-I2-

-IL-

-IM-

-IN-

Fixed length

OFF

all codes

Fixed length

all codes

Fixed length

selected codes

Min. length

selected codes

Max. length

selected codes

Setting Code Specific Options - Options for specific codes may be configured affecting:

Enabling and disabling code variants and translations.

Data verification such as by mean of a check digit calculation. A check digit has a value that can be

calculated from the other data characters and is usually the last data character in a bar code.

Pre-editing of the data string such as removing the check digit and/or ST/SP characters.

The more common options are described here.

Check CD - Enables the check digit calculation. If the calculated check digit does not correspond to the check digit

in the bar code, then the bar code is ignored. The use of a check digit greatly improves the security of a bar code.

Do Not Check CD - Disables the check digit calculation. This option is required when the bar codes do not contain

a check digit or contain an invalid check digit.

Transmit CD - Enables the transmission of the check digit together with the data characters. If the check digit

calculation is disabled, the reader cannot differentiate anymore between a (valid) check digit and a data character. It

will therefore transmit all data characters of the label, including what could constitute a check digit.

Do Not Transmit CD - Disables the transmission of the check digit. If the check digit calculation is disabled, the

reader cannot differentiate between a (valid) check digit and a data character. It will therefore transmit all data

characters of the able, excluding the character that could constitute the check digit for the type of bar code.

Transmit ST/SP - Enables the transmission of the start and stop characters of a bar code.

Do Not Transmit ST/SP - Disables the transmission of the start and stop characters of a bar code.

Page 17

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

UPC Settings

Options for UPC-A and UPC-E bar codes.

NOTE: Abbreviations: Xmit = transmit; CD = Check digit; CC = Country code

Start/End

Program

-[[-

UPC-A

as EAN13

w/ CD

-F3-

(13 digits)

UPC-A

w/ CD

(12 digits)

-F!-

UPC-A

w/ CD

(12 digits)

-F5-

UPC-A

w/o CD

(11 digits)

-F6-

UPC-E

w/ CC & CD

(8 digits)

-F7-

UPC-E

w/o CC,

w/ CD

(7 digits)

-F8-

UPC-E

w/ CC,

w/o CD

-F9-

(7 digits)

UPC-E

w/o CC & CD

(6 digits)

-F:-

Xmit UPC-E

as UPC-A

w/ CD

-7Q-

(8 digits)

Do not

xmit UPC-E

as UPC-A

w/o CD

(7 digits)

-7R-

Page 18

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

UPC Settings (continued)

Options for UPC-A - The UPC-A symbology is a fixed length symbology encoding 11 data digits, a check digit

and non printable start/stop characters. Supported characters are numeric digits 1 to 9.

An optional leading zero can be transmitted which, together with the data and the check digit, forms a 13 digit field

providing compatibility with the EAN-13 format.

String format:

Leading

data

(11 digits)

check

digit

UPC-A add-on 2/add-on 5 - The UPC-A symbology as described above can be succeeded by an additional 2 or 5

digit UPC-A code.

String format:

Leading

data

(11 digits)

check

digit

add-on

2 or 5

Options for UPC-A

Disable transmission of the leading zero

Disable transmission of the check digit

Options for UPC-E - The UPC-E symbology is a fixed length symbology encoding 6 data digits, a check digits and

non printable start/stop characters. Supported characters include numeric digits 0 to 9. An optional leading zero can

be transmitted which, together with the data and the check digit, forms an 8 digit field providing a compatibility with

the EAN-8 format.

String format:

Leading

data

(6 digits)

check

digit

UPC-E add-on 2/add-on 5 - The UPC-E symbology as described above can be succeeded by an additional 2 or 5

digit UPC-A code.

String format:

Leading

data

(6 digits)

check

digit

add-on

2 or 5

Options for UPC-E

Enable transmission of the leading zero

Disable transmission of the check digit

Transmit UPC-E as UPC-A

Page 19

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

EAN-13 and EAN-8 Settings

Start/End

Program

-[[-

-7L-

-7K-

-7J-

-7I-

-JC-

EAN-13

transmit CD

EAN-13

do not

transmit CD

EAN-8

transmit CD

EAN-8

do not

transmit CD

Disable

ISBN

translation

Enable

ISBN

translation

-JB-

-JL-

-IO-

-IP-

-5W-

Enable

ISBN if

possible

Disable

ISSN

translation

Enable

ISSN

translation

Enable

ISSN if

possible

Page 20

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

EAN-13 and EAN-8 Settings

EAN-13 is a fixed length symbology encoding 12 data digits, a check digit and non printable start/stop characters.

Supported characters are numeric digits 0 to 9. The data may be translated into ISBN or ISSN format.

String format:

data

(12 digits)

check

digit

EAN-13 add-on 2/add-on 5 - The EAN-13 symbology as described above can be succeeded by an additional 2 or 5

digit UPC-A code.

String format:

data

(12 digits)

check

digit

add-on

2 or 5

EAN-8 is a fixed length symbology encoding 7 data digits, a check digit and non printable start/stop characters.

Supported characters are numeric digits 0 to 9.

String format:

data

(7 digits)

check

digit

EAN-8 add-on 2/add-on 5 - The EAN-8 symbology as described above can be succeeded by an additional 2 or 5

digit UPC-A code.

String format:

data

(7 digits)

check

digit

add-on

2 or 5

Options for EAN

Disable transmission of the check digit

Enable ISBN or ISSN translation

Enable ISBN or ISSN translation - If this option is enabled, an EAN-13 label is verified for the correct format and

transmitted as a 10 digit ISBN number or 8 digit ISSN number.

Page 21

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Code 39 Settings

Start/End

Program

-[[-

-D1-

Check CD

Do not

check CD

-D2-

-E1-

-E2-

-E%-

-E6-

-E9-

-E:-

Xmit ST/SP

Do not

xmit ST/SP

Full ASCII

Normal

Code 39

Do not

xmit CD

Xmit CD

Full ASCII

Code 39 if

possible

-,L-

-,M-

-,N-

Enable

concat-enation

Disable

concat-enation

Page 22

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Minimum

3 digits

-9E-

-9F-

Minimum

1 digit

CONTINUED ON NEXT PAGE...

Page 23

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Code 39 Settings (continued)

Code 39 is a variable length symbology with an optional check digit ("CD") and printable start/stop ("ST/SP")

characters. The following characters are supported:

•

Numeric characters 0 to 9

Alpha characters capital A to Z

Special characters - $ / + % and SPACE

Start/stop character is *

The checksum is calculated as the sum modulo 43 of the numerical value of the data characters.

In full ASCII mode, all 128 ASCII characters are supported. This is done by combining one of the characters +, %, $

or / with one of the alpha characters (A to Z).

String format:

start

char.

data (0 or

more characters)

check stop

digit char.

Options for Code 39:

Enable full ASCII conversion

Enable Italian Pharmaceutical conversion

Enable check digit

Disable transmission of the check digit

Enable transmission of start/stop

Enable leading A for Italian Pharmaceutical

Selection of the minimum number of data characters

Normal Code 39 - In this mode the decoded data characters are transmitted without further translation.

Full ASCII Code 39 - In this mode the decoded data characters are translated to full ASCII Code 39.

Full ASCII Code 39 if possible - In this mode the decoded data characters are translated to full ASCII code 39.

Invalid combinations are not translated and are transmitted as is.

Concatenation - If a Code 39 bar code contains a leading space, the data is stored into the reader's buffer without

the leading space. As soon as a Code 39 bar code is read without a leading space, the data is appended to the reader's

buffer and the entire buffer is transmitted and cleared for new data. In case a non Code 39 bar code bar is transmitted

and the buffer is cleared. The buffer size is reader dependant.

Page 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Codabar Settings

Start/End

Program

-[[-

-G1-

Do not

transmit

start/stop

Transmit

start/stop as

ABCD/TN*E

-G2-

-G3-

-G!-

-G5-

-I!-

-I5-

-I6-

-I7-

Transmit

start/stop as

abcd/tn*e

Transmit

start/stop as

ABCD/ABCD

Transmit

start/stop as

abcd/abcd

Enable

Codabar,

ABC and CX

Enable only

ABC code

Enable only

CX code

Check CD

Do not

check CD

-I8-

Transmit

-I9-

-I:/

Do not

transmit CD

Page 25

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

CONTINUED ON NEXT PAGE...

Page 26

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Codabar Settings (continued)

Start/End

Program

-[[-

-IB-

Enable

Codabar

normal mode

only

Min. data

3 chars.

-IC-

-ID-

-IE-

Min. data

1 char.

Enable space

insertion

Disable space

insertion

-IF-

-IG-

Min. data

5 chars.

Enable

interchar. gap

check

-II-

-IJ-

Disable

interchar. gap

check

Codabar Settings

Codabar (NW7) is a variable length symbology with an optional check digit and printable start/stop characters.

Supported characters include:

Numeric digits 0 to 9

special characters - $ : / , +

Page 27

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

start/stop characters are A, B, C or D

The checksum is calculated as the sum modulo 16 of the numerical values of all data characters.

String format:

start

char.

data (1 or

more chars.)

check

digit

stop

char.

CONTINUED ON NEXT PAGE...

Page 28

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Codabar Settings (continued)

ABC-Code - The ABC code is an acronym for American Blood Commission. The code consists of two bar codes

which are decoded in one read cycle. the code is concatenated when the stop character of the first bar code and the

start character of the second bar code is a D. These two D's are not transmitted.

String format:

start data (1+ check data (1+ check stop

char.

chars.)

digit

chars.)

digit char.

CX-Code - The CX-Code consists of two are codes which are decoded in one read cycle. The code is concatenated

when the stop character of the first bar code is a C, and the start character of the second bar code is a B. The B and C

characters are not transmitted.

String format:

start data (1+ check data (1+ check stop

char.

chars.)

digit

chars.)

digit char.

Options for Codabar:

Enable ABC code concatenation.

Enable CD code concatenation.

Enable check digit check.

Disable transmission of the check digit.

Disable transmission of start/stop.

Selection of start/stop character translation.

Selection of minimum number of data characters.

Enable library space (CLSI) insertion.

Space insertion - This option inserts spaces in position 2, 7 and 13 of the data string for use in library systems.

ST/SP translation - This option enables the translation and transmission of the start and stop characters. Thus, if the

option ST/SP: abcd/tn*e is chosen, the start character is converted to lower case, e.g. from A, B, C or D to a, b, c or

d, respectively), and the stop character is converted from A, B, C or D to t, n, * or e, respectively.

Minimum data characters - Codabar labels are checked for a minimum of 1, 3 or 5 characters as set by the user. If

the number of characters in the label is shorter than the minimum selected, the label will be rejected. If the fixed

length option is used for Codabar type labels, then such labels will additionally be checked for fixed length. This

option will no longer be supported in future software releases.

Intercharacter gap check - This option enables the reading of Codabar labels with a large or irregular gap between

characters.

Page 29

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

2of5 Settings

Start/End

Program

-[[-

-F1-

-F2-

-H1-

Transmit

Do not

transmit CD

Do not

check CD

Check CD

-H2-

-HF-

-HG-

Min. data

1 char.

Min. data

3 chars.

Min. data

5 chars.

-GJ-

Enable space

check for

Industrial 2of5

-GK-

-HL-

Disable space

check for

Industrial 2of5

CONTINUED ON NEXT PAGE...

Page 30

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

2of5 Settings (continued)

Code 2of5 is a variable length symbology with an optional check digit and non printable start and stop character.

Supported characters include numeric digits 0 to 9.

The checksum is calculated as the sum modulo 10 of the numerical values of all the data characters. The following

2of5 codes are supported.

Industrial 2of5 (D 2of5) - This symbology encodes a pair of digits in each symbol, the number of digits are

therefore always an even number. Information is carried in the bars and spaces. The start and stop pattern in not

unique inside the code. It is therefore essential to use the fixed length option to prevent partial reads.

Matrix 2of5 - This symbology encodes 1 digit in each character, the number of digits can therefore be an odd or an

even number. Information is carried in the bars and spaces.

String format - Industrial, Interleaved or Matrix 2of5:

leading

zero

data (1 or

more digits)

check

digit

Options for Code 2of5:

Disable transmission of the check digit

Enable check digit check

Selection of the minimum number of data characters

Disable space check for industrial 2of5

Transmit S Code as Interleaved 2of5

Minimum data characters - Code 2of5 are checked for a minimum of 1, 3 or 5 characters as set by the user. If the

number of characters in the label is less than the number set, the label will be rejected. If the fixed length option is

used for a Code 2of5 type label, then such label will also be checked for fixed length.

Intercharacter gap check - This option enables the reading of Industrial 2of5 labels with a large or irregular

spacing.

Page 31

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

MSI/Plessey Settings

Start/End

Program

-[[-

-5B-

Do not

check CD

Check 1 CD =

Mod 10

-5C-

Check 2 CD's

= Mod 10

/Mod 10

-%D-

-5E-

Check 2 CD's

= Mod 10

/Mod 11

Transmit CD1

-5F-

Transmit CD1

and CD2

-5G-

-5H-

-5S-

Do not

transmit CD

Check 2 CD's

= Mod 11

/Mod 10

MSI Plessey is a variable length symbology with one or two optional check digit calculations CD1 and CD2 and

non printable start/stop characters. Supported characters include numeric digits 0 through 9.

The checksum is calculated as the sum modulo 10 or 11 of the data characters. The checksum CD2 is calculated as

the sum modulo 10 or 11 of the data characters and CD1.

String format:

data (1 to

CD1 CD2

13 digits)

Options for MSI/Plessey:

Disable check digit check.

Selection of the check digit calculation.

Selection of the number of check digits to be transmitted.

Page 32

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Check digit - If the check digit calculation is required, then the appropriate calculation method must be selected.

Do not transmit CD - The character positions CD1 and CD2 are not transmitted.

Transmit CD1 - The character position CD2 is not transmitted.

Transmit CD1 and CD2 - All characters in the label are transmitted.

Page 33

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Code 128, EAN 128 Settings

Start/End

Program

-[[-

-KG-

-NP-

Enable

EAN 128

only

Enable FNC2

concat-enation

Disable FNC2

concat-enation

-NQ-

Disable

EAN 128

-PG-

-PH-

Enable

EAN 128

if possible

Code 128 is a variable length symbology with a mandatory check digit and non-printable start/stop characters.

Supported characters include:

All 128 ASCII characters;

4 non data function characters;

4 code set selection characters;

3 start characters; and

1 stop character.

The check is calculated as the sum modulo 103 of the start character and the weighted values of the data and special

characters.

String format:

data (1 or more characters)

EAN 128 - In this mode, the Code 128 data is translated to the EAN 128 format. EAN 128 data starts with the FNC1

character and separates 2 data fields with the FNC1 character. The first FNC1 character is translated to ]C1, and the

second FNC1 character is translated to ASCII GS (hex 1D) character.

String format:

data

characters

data

characters

]C1

<GS>

Enable EAN 128 only - In the mode, the decoded data characters are translated to the EAN 128 format. If the data

does not comply with the EAJ 128 format, then the label is rejected.

Enable EAN 128 if possible - In this mode, the decoded data characters are translated to the EAN 128 format. If the

data does not comply with the EAN 128 format, then the label is transmitted as Code 128.

Page 34

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

FNC2 Concatenation - If a Code 128 bar code contains a leading FNC2 character, the data is stored into the

reader's buffer. As soon as a Code 128 bar code is read without a leading FNC2 character, the data is appended to

the reader's buffer and the entire buffer is transmitted and cleared for new data. In case a non Code 128 bar code is

read, the data in the non-Code 128 bar code is transmitted and the buffer is cleared. The buffer size is reader

dependent.

Page 35

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

IATA Settings

Start/End

Program

-[[-

Do not

check CD

-!5I-

Check S/N

only

-5J-

-5K-

-5L-

Check CPN,

S/N

Check CPN,

airline and

S/N

Transmit CD

-5M-

-5N-

Do not

transmit CD

IATA is a variable length symbology with an optional check digit and non printable start/stop characters. Supported

characters include numeric digits 0 through 9.

The checksum is calculated as the modulo seven of the data string. IATA is acronym for International Air Transport

Association.

String format - A possible format of IATA is as follows:

Code

Description Coupon Airline Code Form Code Serial Number Check Digit

Digits

CPN

Options for IATA:

Enable check digit check.

Selection of the check digit calculation.

Disable transmission of the check digit.

Check digit - If the check digit calculation is required, then the appropriate calculation method must be selected.

Page 36

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Telepen Settings

Start/End

Program

-[[-

-E3-

-E!-

Numeric

mode

ASCII mode

Telepen is a variable length symbology with a check digit and non printable start/stop characters. Supported

characters include numeric digits 00 through 99 in numeric mode, and all 128 ASCII characters in full ASCII mode.

The check digit calculation is derived from the sum of all data characters modulo 127. The check digit cannot be

transmitted.

String format:

Data

(1 to 32 characters)

Options for Telepen:

Selection of full ASCII mode.

Page 37

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Case Conversion

Start/End

Program

-[[-

-Z[-

No case

conversion

Convert to

upper case

-ZX-

-ZY-

-ZZ-

Convert to

lower case

Exchange case

String Options - This section describes the alterations which can be made to the format of the transmitted data string.

Options available are:

Case conversion

Transmission of a code identifier

Transmission of the code length

Transmission of a prefix

Transmission of a suffix

The prefix and/or suffix may include a code identifier and/or the code length.

String format:

bar code

data

suffix

prefix

Case conversion - The bar code may be converted to either lower of upper case or the case my be exchanged. These

options may be used if the user of a wedge has a preference to leave, for instance, the CAPSLOCK ON or if the host

required upper case characters only.

Page 38

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Setting a Prefix or Suffix

A Prefix and Suffix consisting of a maximum 4 direct input entries each may be included in front and at the end of

the string, respectively.

The following steps are used to establish a Prefix or Suffix that will be transmitted with the bar code data.

Scan Start/End Program Menu to enter programming mode.

Scan the bar code representing the desired symbology you wish to add a Prefix or Suffix to.

Scan the character(s) that comprise the Prefix or Suffix. Up to 4 numbers, letters or control characters may

be used.

Scan Start/End Program Menu to exit programming mode.

Prefix Settings

Start/End

Program

-[[-

-HM-

-J9-

-M9-

/N1-

-N2-

-N!-

-N5-

-N6-

-N7-

Matrix 2of5

IATA

Telepen

UPC-A

+ add-on

UPC-E

+ add-on

EAN-13

+ add-on

EAN-8

+ add-on

Code 39

Codabar

Industrial 2of5

CONTINUED ON NEXT PAGE...

Page 39

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Prefix Settings (continued)

Start/End

Program

-[[-

-N8-

-N9-

-N:-

-O1-

-O2-

-O3-

-O!-

-O5-

-SZ-

-NH-

-N[-

Interleaved

2of5

Code 93

Code 128

MSI/Plessey

UPC-A

UPC-E

EAN-13

EAN-8

All codes

Clear all

prefixes

Preamble

Page 40

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Suffix Settings

Start/End

Program

-[[-

-HN-

-J:-

-M:-

-O6-

-O7-

-O8-

-O9-

-O:-

-P1-

-P2-

-P3-

-P!-

-P5-

-P6-

Matrix 2of5

IATA

Telepen

MSI/Plessey

UPC-A

UPC-E

EAN-13

EAN-8

UPC-A

+ add-on

UPC-E

+ add-on

EAN-13

+ add-on

EAN-8

+ add-on

Code 39

Codabar

CONTINUED ON NEXT PAGE...

Page 41

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Suffix Settings (continued)

Start/End

Program

-[[-

-P7-

-P8-

-P9-

-P:-

-QS-

-QT-

-S[-

Industrial

2of5

Interleaved

2of5

Code 93

Code 128

Clear all

suffixes

Postamble

All Codes

Page 42

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Keyboard Keys

Start/End

Program

-[[-

-9K-

-9L-

-9M-

-9N-

-9O-

-9P-

-9Q-

-9R-

-9S-

-9T-

-9U-

-9V-

-:Y-

-8I-

F10

F11

F12

Backspace

TAB

CONTINUED ON NEXT PAGE...

Page 43

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Keyboard Keys (continued)

Start/End

Program

-[[-

-8J-

Carriage

return

Enter

(numeric pad)

-8R-

-8S-

-8E-

-8K-

-8L-

-8M-

-8N-

-8O-

-8U-

-WR-

-WS-

-WT-

-8P-

Enter make

(alpha pad)

Enter make

and break

(alpha pad)

ESC

Arrow down

Arrow up

Arrow right

Arrow left

<DEL>

<HOME>

<END>

Page up

CONTINUED ON NEXT PAGE...

Page 44

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Keyboard Keys (continued)

Start/End

Program

-[[-

-8Q-

-8V-

-8X-

-8Z-

-8W-

-8Y-

-8[-

-:T-

Page down

Left

<Shift>

Left

<Ctrl>

Left

<Alt>

Right

<Shift>

Right

<Ctrl>

Right

<Alt>

CAPSLOCK

Page 45

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Characters

Start/End

Program

-[[-

-6B-

-6C-

-6D-

-6E-

-6F-

-6G-

-6H-

-6I-

-6J-

-6K-

-6L-

-6M-

-6N-

-6O-

<SPACE>

(

)

CONTINUED ON NEXT PAGE...

Page 46

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Characters (continued)

Start/End

Program

-[[-

-6P-

-6Q-

-7B-

-7C-

-7D-

-7E-

-7F-

-7G-

-7H-

-8B-

-8C-

-8D-

-8E-

-8F-

;

[

]

CONTINUED ON NEXT PAGE...

Page 47

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Characters (continued)

Start/End

Program

-[[-

-8G-

-:U-

-:V-

-:W-

-:X-

{

}

CONTINUED ON NEXT PAGE...

Page 48

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Characters (continued)

Start/End

Program

-[[-

-R1-

-R2-

-R3-

-R!-

-R5-

-R6-

-R7-

-R8-

-R9-

-R:-

-1B-

-1C-

-1D-

CONTINUED ON NEXT PAGE...

Page 49

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Characters (continued)

Start/End

Program

-[[-

-1E-

-1F-

-1G-

-1H-

-1I-

-1J-

-1K-

-1L-

-1M-

-1N-

-1O-

-1P-

-1Q-

-1R-

CONTINUED ON NEXT PAGE...

Page 50

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Characters (continued)

Start/End

Program

-[[-

-1S-

-1T-

-1U-

-1V-

-1W-

-1X-

-1Y-

-1Z-

-1[-

-%B-

-%C-

-%D-

-%E-

-%F-

CONTINUED ON NEXT PAGE...

Page 51

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Characters (continued)

Start/End

Program

-[[-

-%G-

-%H-

-%I-

-%J-

-%K-

-%L-

-%M-

-%N-

-%O-

-%P-

-%Q/

-%R-

-%S-

-%T-

CONTINUED ON NEXT PAGE...

Page 52

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Characters (continued)

Start/End

Program

-[[-

-%U-

-%V-

-%W-

-%X-

-%Y-

-%Z-

-%[-

Page 53

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Control Characters

Start/End

Program

-[[-

-:H-

-2B-

-2C-

-2D-

-2E-

-2F-

-2G-

-2H-

-2I-

-2J-

-2K-

-2L-

-2M-

-2N-

^@(NULL)

^A(SOH)

^B(STX)

^C(ETX)

^D(EOT)

^E(ENQ)

^F(ACK)

^G(BEL)

^H(BS)

^I(HT)

^J(LF)

^K(VT)

^L(FF)

^M(CR)

CONTINUED ON NEXT PAGE...

Page 54

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Control Characters (continued)

Start/End

Program

-[[-

-2O-

-2P-

-2Q-

-2R-

-2S-

-2T-

-2U-

-2V-

-2W-

-2X-

-2Y-

-2Z-

-2[-

-:B-

^N(SO)

^O(SI)

^P(DLE)

^Q(DC1)

^R(DC2)

^S(DC3)

^T(DC4)

^U(NAK)

^V(SYN)

^W(ETB)

^X(CAN)

^Y(EM)

^Z(SUB)

^[(ESC)

CONTINUED ON NEXT PAGE...

Page 55

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Direct Input Control Characters (continued)

Start/End

Program

-[[-

-:C-

-:D-

-:E-

-:F-

-:G-

^\(FS)

^](GS)

^^(RS)

^_(US)

DEL

(ASCII 127)

Direct Input Code ID/Length

Start/End

Program

-[[-

-%3-

-%!-

Code

identification

Code length

Page 56

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Read Mode Settings

Start/End

Program

-[[-

-T1-

Single

read

Multiple

read

-T2-

Continuous

read

-T3-

-YB-

-TC-

Add-on

wait mode

disabled

Add-on

wait mode

0.25 sec.

Add-on

wait mode

0.50 sec.

-YD-

Add-on

wait mode

0.70 sec.

-YE-

Single Read - When a bar code has been decoded, the reader will be turned OFF. The reader must be triggered again

to read another label. This option and "Disable trigger" cannot be programmed at the same time.

Multiple Read - When a bar code has been decoded, the reader will stay ON for a time as set by "read time

settings" or indefinitely if the trigger switch has been disabled. The same label can only be decoded again after the

label has not been detected for a number of scans.

Continuous Read - The reader will produce as much data as it can decode regardless whether it is the same or not.

This mode is mainly used for demonstration and diagnosis.

Add-on Wait Mode - Used if UPC/EAN with add-on is enabled. The reader searches within the selected time for a

valid add-on code. If a valid add-on code is found, the reader transmits the data immediately. If nothing is found

behind the code, the scanner will transmit the data without add-on. If something is found behind the code, the reader

ignored the code in case it is not a valid add-on.

Page 57

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Trigger Settings

Start/End

Program

-[[-

-T8-

-T9-

Disable

trigger

Enable

trigger

Disable Trigger - This is applicable to readers which have a trigger switch. When this option is selected, the reader

will stay ON all the time.

Multiple Read Reset Time

Start/End

Program

-[[-

50 ms

-BI-

100 ms

-BJ-

200 ms

-BK-

300 ms

-BL-

400 ms

-BM-

500 ms

-BN-

600 ms

-BO-

Multiple Read Reset Time - This option can be used in conjunction with multiple read mode. It sets the time the

reader should be pointed away from the label before it can decode the same label again.

Page 58

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Quiet Zone Settings

Start/End

Program

-[[-

-ZO-

-ZP-

-ZQ-

-ZR-

-ZS-

-ZE-

-ZU-

No margin

check

Margin

check 1/7

normal

Margin

check 2/7

normal

Margin

check 3/7

normal

Margin

check 4/7

normal

Margin

check 5/7

normal

Margin

check 6/7

normal

Margin

check

normal

-ZV-

With these settings, the reader can decode bar codes that have smaller start and/or end margins than specified for the

symbology. These settings may increase the possibility of partial and ghost reads, hence do not use smaller margin

checks than necessary. Replace any bar code labels with ones that have the correct start and end margins if possible.

Page 59

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Read Time Settings

Start/End

Program

-[[-

-Z1-

-Z2-

0 seconds

1 second

2 seconds

-Z3-

3 seconds

4 seconds

5 seconds

6 seconds

7 seconds

8 seconds

-Z!-

-Z5-

-Z6-

-Z7-

-Z8-

-Z9-

-ZM-

-ZN-

Read time

x 10

Indefinitely

Read Time Settings - the length of the period that the reader is ON after the trigger switch is pressed, or (in

multiple or continuous read mode) after a label has been read. Selecting a read time of 0 means that the reader will

stay ON as long as the trigger switch is being pressed. Selecting a read time for readers without a trigger switch, or

when the trigger switch is disabled, has no effect.

Page 60

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Redundant Decoding Settings

Start/End

Program

-[[-

-Y1-

redundancy

Two times

redundant

-Y2-

Three times

redundant

-Y3-

-Y!-

Four times

redundant

Redundancy Settings - This is the number of times that a label must be correctly decoded before it is transmitted.

Selecting a higher redundancy count makes reading slower, but it reduces the probability of reading errors,

especially when labels of poor definition are used.

Positive and Negative Bar Codes

Start/End

Program

-[[-

Positive

bar codes

-W3-

Both positive

and negative

bar codes

-W5-

Positive and Negative Bar Codes - Usually bar codes are printed black on white, but sometime white on black.

These labels are called positive and negative, respectively.

Page 61

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Buzzer Settings

Start/End

Program

-[[-

-X9-

Enable

software

buzzer

Disable

buzzer

-X1-

-X2-

Single tone

buzzer

High - low

buzzer

-X3-

Low - high

buzzer

-X!-

-X8-

-X5-

Buzzer

duration

50 msec.

Buzzer

duration

100 msec.

Buzzer

duration

200 msec.

-X6-

-X7-

-U1-

-U2-

Buzzer

duration

400 msec.

Buzzer

volume

maximum

Buzzer

volume

loud

Page 62

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Buzzer

volume

normal

-U3-

-U!-

Buzzer

volume

minimum

Buzzer before

transmission

-WZ-

CONTINUED ON NEXT PAGE...

Page 63

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Buzzer Settings

Start/End

Program

-[[-

-W[-

-HE-

-HD-

Buzzer

after

transmission

Disable

startup buzzer

Enable startup

buzzer

Buzzer Settings - These options determine the buzzer type, tone, duration and loudness. By default, the buzzer is

disabled for Linker type readers.

Buzzer Type - The buzzer may be disabled or enabled as either a hardware of software buzzer. Not all readers

support both a hardware and software buzzer.

Buzzer Tone - If a software buzzer is used, the buzzer tone may be selected.

Buzzer Duration and Volume - If a software buzzer is used, a buzzer duration of 50, 100, 200 or 400 msec. may be

selected. Volume may also be adjusted.

Buzzer Before Transmission - The good read buzzer will be activated after decoding the bar code, but before

transmission. During transmission, the buzzer sequence will be completed.

Buzzer After Transmission - The good read buzzer will be activated after transmission.

Enable Startup Buzzer - When this option is selected, the reader will generate a single good read buzzer to

indicate the reader is ready after the reader is supplied with power.

Disable Startup Buzzer - When this option is selected, the reader will not sound the buzzer after the reader is

supplied with power.

Page 64

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual No. 25-ULGPMU01-01

CCD Scanner

Series OPT Handheld

Good Read LED

Start/End

Program

-[[-

-U5-

Disable

indicator

Indicator

duration

0.2 sec.

-U6-

Indicator

duration

0.4 sec.

-U7-

-U8-

Indicator

duration

0.8 sec.

Diagnostics

Start/End

Program

-[[-

-[2-

-[!-

-[B-

-ZW-

-UI-

-UJ-

Transmit

software

version

Transmit

settings

Transmit

ASCII

printable

string

Transmit

ASCII control

string

Error msg.

label

Error msg. no

decode

Page 65

Download from Www.Somanuals.com. All Manuals Search And Download.

National Mower Lawn Mower HY70OM 8 992 User Manual
Nespresso Coffeemaker AEROCINNO 3190 User Manual
Nexstar Computer Drive NST 210S2 BK User Manual
Nikon Camera Lens 200mm F 2 User Manual
Oki Printer 8 8N User Manual
Olympus Camera Accessories EP 1 User Manual
Olympus Camera Lens 261009 User Manual
Oster Microwave Oven OTM1101GBS User Manual
Panasonic Cordless Saw EY3544 User Manual
Patton electronic Power Supply 2036 User Manual