Onkyo Stereo System HT S7300 User Manual

Contents

7.1ch Home Theater System

Introduction ...................................2

Connections.................................14

Turning On & Basic Operations ......24

Advanced Operations .................38

HT-S7300

AV Receiver (HT-R680)

Speaker Package (HTP-780)

Universal Port Option Dock for iPod^®

(UP-A1)

HT-S6300

AV Receiver (HT-R680)

Speaker Package (HTP-680)

Universal Port Option Dock for iPod^®

(UP-A1)

Controlling iPod & Other

Components............................56

Instruction Manual

Others...........................................64

Thank you for purchasing an Onkyo 7.1ch Home

Theater System. Please read this manual thoroughly

before making connections and plugging in the unit.

Following the instructions in this manual will enable

you to obtain optimum performance and listening

enjoyment from your new 7.1ch Home Theater

System.

Please retain this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal without

the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not user-ser-

viceable. If you cannot turn on the unit, contact your

Onkyo dealer.

3. Care—Occasionally you should dust the unit all over

with a soft cloth. For stubborn stains, use a soft cloth

dampened with a weak solution of mild detergent and

water. Dry the unit immediately afterwards with a

clean cloth. Don’t use abrasive cloths, thinners, alco-

hol, or other chemical solvents, because they may

damage the finish or remove the panel lettering.

4. Power

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved

by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio

or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit differ-

ent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV techni-

cian for help.

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SECTION

CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the volt-

age requirements printed on the unit’s rear panel (e.g.,

AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug is

readily operable (easily accessible) at all times.

Pressing ON/STANDBY to select Standby mode does

not fully shutdown the unit. If you do not intend to use

the unit for an extended period, remove the power cord

from the AC outlet.

5. Preventing Hearing Loss

Caution

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS COM-

PLIES WITH CANADIAN ICES-003.

Excessive sound pressure from earphones and head-

phones can cause hearing loss.

6. Batteries and Heat Exposure

Warning

For models having a power cord with a polarized plug:

Batteries (battery pack or batteries installed) shall not

be exposed to excessive heat as sunshine, fire or the

like.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

7. Never Touch this Unit with Wet Hands—Never han-

dle this unit or its power cord while your hands are

wet or damp. If water or any other liquid gets inside

this unit, have it checked by your Onkyo dealer.

8. Handling Notes

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME NMB-

003 DU CANADA.

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally

bought it.

• Do not leave rubber or plastic items on this unit for

a long time, because they may leave marks on the

case.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE

DE LA FICHE DANS LA BORNE CORRESPON-

DANTE DE LA PRISE ET POUSSER JUSQU’AU

FOND.

• This unit’s top and rear panels may get warm after

prolonged use. This is normal.

• If you do not use this unit for a long time, it may not

work properly the next time you turn it on, so be

sure to use it occasionally.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker Precautions

Package Contents

Make sure you have the following items:

Placement

In catalogs and on packaging, the letter at the end of the prod-

uct name indicates the color. Specifications and operations are

the same regardless of color.

• The subwoofer cabinet is made out of wood and is there-

fore sensitive to extreme temperatures and humidity, do

not put it in locations subject to direct sunlight or in

humid places, such as near an air conditioner, humidifier,

bathroom, or kitchen.

HT-S6300

• Do not put water or other liquids close to the speakers. If

liquid is spilled over the speakers, the drive units may be

damaged.

AV Receiver HT-R680

HT-R680 (➔ 8)

• Speakers should only be placed on sturdy, flat surfaces

that are free from vibration. Putting them on uneven or

unstable surfaces, where they may fall and cause dam-

age, will affect the sound quality.

• Subwoofer is designed to be used in the upright vertical

position only. Do not use it in the horizontal or tilted

position.

Remote controller and two batteries (AA/R6) (➔ 5)

Indoor FM antenna (➔ 22)

AM loop antenna (➔ 22)

Speaker setup microphone (➔ 28)

Speaker Package HTP-680

• If the unit is used near a turntable, CD player or Blu-ray

Disc/DVD player, howling or slipping of sound may

occur. To prevent this, move the unit away from the turn-

table, CD player or Blu-ray Disc/DVD player, otherwise

lower the unit’s output level.

Front speakers (SKF-680 L/R) (➔ 10)

Center speaker (SKC-680) (➔ 10)

Surround speakers (SKR-680 L/R) (➔ 10)

Surround back speakers (SKB-680 L/R) (➔ 10)

Subwoofer (SKW-770) (➔ 10)

Using Close to a TV or Computer

Speaker cables for front speakers 11 ft. (3.5 m)

(White and Red) (➔ 17)

TVs and computer monitors are magnetically sensitive

devices and as such are likely to suffer discoloration or

picture distortion when conventional speakers are placed

nearby. In such situations, try moving the speakers away

from your TV or monitor. If discoloration should occur,

turn off your TV or monitor, wait 15 to 30 minutes, and

then turn it back on again. This normally activates the

degaussing function, which neutralizes the magnetic field,

thereby removing any discoloration effects. Note that dis-

coloration can also be caused by a magnet or demagnetiz-

ing tool that’s too close to your TV or monitor.

Speaker cable for center speaker 10 ft. (3.0 m)

(Green) (➔ 17)

Speaker cables for surround speakers 26 ft. (8.0 m)

(Blue and Gray) (➔ 17)

Speaker cables for surround back speakers 26 ft.

(8.0 m) (Brown and Tan) (➔ 17)

RCA cable for subwoofer connection 10 ft. (3.0 m)

(➔ 17)

28 rubber stoppers (➔ 14, 15)

4 floor pads for the subwoofer (➔ 15)

Universal Port Option Dock for iPod

(UP-A1)

Input Signal Warning

The speakers can handle the specified input power when

used for normal music reproduction. If any of the follow-

ing signals are fed to them, even if the input power is

within the specified rating, excessive current may flow in

the speaker coils, causing burning or wire breakage:

1. Interstation noise from an untuned FM radio.

2. Sound from fast-forwarding a cassette tape.

3. High-pitched sounds generated by an oscillator, elec-

tronic musical instrument, and so on.

UP-A1 (➔ 56)

HT-S7300

AV Receiver HT-R680

HT-R680 (➔ 8)

Remote controller and two batteries (AA/R6) (➔ 5)

Indoor FM antenna (➔ 22)

4. Amplifier oscillation.

5. Special test tones from audio test CDs and so on.

6. Thumps and clicks caused by connecting or discon-

necting audio cables (always turn off your amplifier

before connecting or disconnecting cables).

AM loop antenna (➔ 22)

Speaker setup microphone (➔ 28)

7. Microphone feedback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker Package HTP-780

Contents

Front speakers (SKF-780 L/R) (➔ 10)

Center speaker (SKC-780) (➔ 10)

Introduction

Surround speakers (SKR-780 L/R) (➔ 10)

Surround back speakers (SKB-780 L/R) (➔ 10)

Subwoofer (SKW-780) (➔ 10)

Important Safety Instructions .........................................2

Precaution s .......................................................................3

Speaker Precaution s ........................................................4

Package Contents ............................................................4

Features ............................................................................6

Front & Rear Panels.........................................................8

Speaker Packag e ............................................................1 0

Remote Controller..........................................................12

About Home Theater......................................................13

Speaker cables for front speakers 11 ft. (3.5 m)

(White and Red) (➔ 17)

Speaker cable for center speaker 10 ft. (3.0 m)

(Green) (➔ 17)

Speaker cables for surround speakers 26 ft. (8.0 m)

(Blue and Gray) (➔ 17)

Connections

Speaker cables for surround back speakers 26 ft.

(8.0 m) (Brown and Tan) (➔ 17)

Connecting the AV Receiver .........................................1 4

RCA cable for subwoofer connection 10 ft. (3.0 m)

(➔ 17)

Turning On & Basic Operations

2 speaker bases and 8 screws (➔ 14)

4 cork stoppers for center speaker (➔ 15)

4 floor pads for the subwoofer (➔ 15)

Turning On/Off the AV Receiver ...................................2 4

Basic Operations............................................................25

Listening to the Radio....................................................3 0

Recording........................................................................3 2

Using the Listening Modes............................................33

Universal Port Option Dock for iPod

(UP-A1)

Advanced Operations

Advanced Setup .............................................................38

Zone 2..............................................................................53

UP-A1 (➔ 56)

Using the Remote Controller

Installing the Batteries

Note

Controlling iPod & Other Components

Controlling iPod .............................................................5 6

Controlling Other Components.....................................6 0

Others

• If the remote controller

doesn’t work reliably, try

replacing the batteries.

• Don’t mix new and old

batteries or different

Troubleshooting.............................................................64

Specifications.................................................................69

About HDMI.....................................................................72

Using an RIHD-compatible TV, Player, or Recorder ...73

Video Resolution Chart..................................................75

types of batteries.

• If you intend not to use

the remote controller for

a long time, remove the batteries to prevent damage from leak-

age or corrosion.

• Remove expired batteries as soon as possible to prevent damage

from leakage or corrosion.

Batteries (AA/R6)

To reset the AV receiver to its factory defaults, turn it

on and, while holding down VCR/DVR, press

ON/STANDBY (➔ 64).

Aiming the Remote Controller

To use the remote controller, point it at the AV receiver’s

remote control sensor, as shown below.

Remote control sensor

AV receiver

Approx. 16 ft. (5 m)

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

AV Receiver HT-R680

• 130 Watts/Channel @ 6 ohms

• WRAT–Wide Range Amplifier Technology

(5 Hz to 100 kHz bandwidth)

• Optimum Gain Volume Circuitry

• H.C.P.S. (High Current Power Supply) Massive High

Power Transformer

Manufactured under license under U.S. Patent #’s: 5,451,942;

5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;

7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and

worldwide patents issued & pending. DTS and the Symbol are

registered trademarks, & DTS-HD, DTS-HD Master Audio,

and the DTS logos are trademarks of DTS, Inc. Product

includes software.

• HDMI (Ver.1.4 with Audio Return Channel, 3D), Deep-

Color, x.v.Color , Lip Sync, DTS -HD Master Audio,

DTS-HD High Resolution Audio, Dolby TrueHD ,

Dolby Digital Plus, DSD and Multi-CH PCM

• Dolby Pro Logic IIz (with “Front High” Direction

Mode)

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are trade-

marks of Dolby Laboratories.

• Non-Scaling Configuration

• A-Form Listening Mode Memory

• Direct Mode

Music Optimizer™ is a trademark of Onkyo Corporation.

• Music Optimizer for Compressed Digital Music files

“HDMI, the HDMI Logo, and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other countries.”

• 192 kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit Processing DSP

• Jitter Cleaning Circuit Technology

• 4 HDMI Inputs and 1 Output

HD Radio™ and the HD Radio Ready logo are proprietary

trademarks of iBiquity Digital Corporation.

To receive HD Radio broadcasts, you must install an Onkyo

UP-HT1 HD Radio tuner module (sold separately).

• Onkyo p for System Control

• 4 Digital Inputs (2 Optical/2 Coaxial)

• Component Video Switching (2 Inputs/1 Output)

• Front “Line in” Input for Portable audio player

• Universal Port for the Dock for iPod /HD Radio™

tuner module

• Banana Plug-Compatible Speaker Posts

• Powered Zone 2

• 40 FM/AM Presets

®*6

Manufactured under license from Audyssey Laboratories™.

U.S. and foreign patents pending. Audyssey 2EQ^®,

Audyssey Dynamic Volume^®and Audyssey Dynamic EQ^®

are registered trademarks and trademarks of

Audyssey Laboratories.

• Audyssey 2EQ

to Correct Room Acoustic Problems

®*6

• Audyssey Dynamic EQ

for Loudness Correction

®*6

• Audyssey Dynamic Volume

to Maintain Optimal

Listening Level and Dynamic Range

• Crossover Adjustment

(40/50/60/70/80/90/100/120/150/200 Hz)

• A/V Sync Control Function (up to 200 ms)

• On-Screen Display via HDMI

iPod is a trademark of Apple Inc., registered in the U.S. and

other countries.

• Preprogrammed u-Compatible Remote

iPhone is a trademark of Apple Inc.

“Made for iPod” means that an electronic accessory has been

designed to connect specifically to iPod and has been certified

by the developer to meet Apple performance standards.

“Works with iPhone” means that an electronic accessory has

been designed to connect specifically to iPhone and has been

certified by the developer to meet Apple performance stan-

dards.

Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards.

“x.v.Color” is a trademark of Sony Corporation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker Package HTP-680

Universal Port Option Dock for iPod

(UP-A1)

SKF-680 L/R 2-Way Front Speakers

• 4" (10 cm) Cone woofer

• 1" (2.5 cm) Balanced dome tweeter

• Max. input power: 130 W

• Easily links iPod/iPhone models with Onkyo A/V Sys-

tems.

• Gloss Finished

• 6-ohm impedance

• Color-coded speaker terminals and speaker cable

SKC-680 2-Way Center Speaker

• 4" (10 cm) Cone woofer

• 1" (2.5 cm) Balanced dome tweeter

• Max. input power: 130 W

• Gloss Finished

• 6-ohm impedance

• Color-coded speaker terminals and speaker cable

SKR-680 L/R Full-Range Surround Speakers

SKB-680 L/R Full-Range Surround Back Speakers

• 3-1/4" (8 cm) Full-Range Speaker

• Max. input power: 130 W

• Gloss Finished

• 6-ohm impedance

• Color-coded speaker terminals and speaker cable

SKW-770 Bass Reflex Powered Subwoofer

• 10" (25 cm) Cone

• Output Level Control

• Max. power: 290 W (Dynamic power)

Speaker Package HTP-780

SKF-780 L/R 2-Way Front Speakers

• 3-1/4" (8 cm) Cone woofer

• 1" (2.5 cm) Balanced dome tweeter

• Max. input power: 130 W

• 6-ohm impedance

• Color-coded speaker terminals and speaker cable

SKC-780 2-Way Center Speaker

• 3-1/4" (8 cm) Cone woofer

• 1" (2.5 cm) Balanced dome tweeter

• Max. input power: 130 W

• 6-ohm impedance

• Color-coded speaker terminals and speaker cable

SKR-780 L/R Full-Range Surround Speakers

SKB-780 L/R Full-Range Surround Back Speakers

• 3-1/4" (8 cm) Cone

• Max. input power: 130 W

• 6-ohm impedance

• Color-coded speaker terminals and speaker cable

SKW-780 Bass Reflex Powered Subwoofer

• 10" (25 cm) Cone

• Output Level Control

• Max. power: 290 W (Dynamic power)

Download from Www.Somanuals.com. All Manuals Search And Download.

Front & Rear Panels

Front Panel

b cd e f g

i j k l m

q r

t u v w

The actual front panel has various logos printed on it. They are not shown here for clarity.

The page numbers in parentheses show where you can find the main explanation for each item.

a ON/STANDBY button (➔ 24)

b STANDBY indicator (➔ 24)

c HDMI THRU indicator (➔ 49)

d ZONE 2 indicator (➔ 54)

e Remote control sensor (➔ 5)

m SETUP button (➔ 38)

n TUNING, PRESET (➔ 30 to 31), arrow and

ENTER buttons

o RETURN button

p MASTER VOLUME control (➔ 25)

q MUSIC OPTIMIZER button (➔ 51)

r PHONES jack (➔ 27)

f ZONE 2, OFF, ZONE 2 LEVEL/TONE LEVEL

and TONE buttons (➔ 50, 54 to 55)

g Display (➔ 9)

s Input selector buttons (BD/DVD, VCR/DVR,

CBL/SAT, GAME, AUX, TUNER, TV/CD and

PORT) (➔ 25)

h LISTENING MODE buttons (MOVIE/TV, MUSIC

and GAME) (➔ 33)

t AUX INPUT LINE IN jack (➔ 20)

u AUX INPUT VIDEO jack (➔ 20)

v AUX INPUT AUDIO jacks (➔ 20)

w SETUP MIC jack (➔ 28)

i DIMMER button (➔ 26)

j MEMORY button (➔ 31)

k TUNING MODE button (➔ 30)

l DISPLAY button (➔ 25)

Download from Www.Somanuals.com. All Manuals Search And Download.

Display

For detailed information, see the pages in parentheses.

a Audio input indicators

e SLEEP indicator (➔ 26)

f MUTING indicator (➔ 26)

g Message area

b Listening mode and format indicators (➔ 33, 51)

c Audyssey indicators (➔ 28, 44)

d Tuning indicators (➔ 30)

Rear Panel

b c d

a DIGITAL IN OPTICAL and COAXIAL jacks

b COMPONENT VIDEO IN and OUT jacks

c HDMI IN and OUT jacks

i u REMOTE CONTROL jack

j Composite video and analog audio jacks

(BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN,

GAME IN and TV/CD IN)

d FM ANTENNA jack and AM ANTENNA terminal

e MONITOR OUT V jack

k ZONE 2 LINE OUT jacks

l SUBWOOFER PRE OUT jack

f UNIVERSAL PORT jack

m FRONT HIGH OR ZONE 2 SPEAKERS terminals

g SPEAKERS terminals

(CENTER, FRONT, SURR and

SURR BACK OR FRONT HIGH)

See “Connecting the AV Receiver” for connection infor-

mation (➔ 16 to 23).

h Power cord

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker Package

Subwoofer (SKW-770/780)

For detailed information, see the pages in parentheses.

■ Front

■ Rear

b c

To AC outlet

a Standby/On indicator

b OUTPUT LEVEL control (➔ 25)

This control is used to adjust the volume of the sub-

woofer.

Red:

Blue:

Subwoofer in standby mode

Subwoofer on

c LINE INPUT (➔ 17)

With the Auto Standby function, the SKW-770/780

automatically turns on when an input signal is

detected in Standby mode. When there’s no input sig-

nal for a while, the SKW-770/780 automatically enters

Standby mode.

This RCA input should be connected to the SUB-

WOOFER PRE OUT on the AV receiver with sup-

plied RCA cable.

Note

• The Auto Standby function turns the subwoofer on when the

input signal exceeds a certain level. If the Auto Standby function

does not work reliably, try slightly increasing or decreasing the

subwoofer output level on the AV receiver (➔ 42).

Front, Center, Surround and Surround Back Speakers

■ HTP-680 (SKF-680, SKC-680, SKR-680, SKB-680)

SKF-680

SKC-680

b a

Front

Rear

Front

Rear

SKR-680/SKB-680

Front

Rear

Download from Www.Somanuals.com. All Manuals Search And Download.

■ HTP-780 (SKF-780, SKC-780, SKR-780, SKB-780)

SKF-780

SKC-780

a b

Rear

Front

SKR-780/SKB-780

Front

Rear

Front

Rear

a Keyhole slots

These keyhole slots can be used to wall-mount the

speaker. See “Wall Mounting” for mounting instruc-

tions (➔ 14).

b Speaker terminals

These push terminals are for connecting the speaker to

the HT-R680 with the supplied speaker cables.

The supplied speaker cables are color-coded for easy

identification. Simply connect each cable to the same-

colored positive speaker terminal.

Caution

• The front grilles are not designed to be removed so do

not attempt to remove them forcibly, as this will damage

them.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Controller

Controlling the AV Receiver

To control the A V r eceiver, press RECEIVER to select

Receiver mode.

You can also use the remote controller to control

Onkyo Blu-ray Disc/DVD player, CD player and

other components.

See “Entering Remote Control Codes” for more

details (➔ 61).

For detailed information, see the pages in parentheses.

a ON/STANDBY button (➔ 24)

b REMOTE MODE/INPUT SELECTOR buttons

(BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TUNER, TV/CD and PORT) (➔ 25)

k^*2

c SP LAYOUT button (➔ 26)

d Arrow q/w/e/r and ENTER buttons

e SETUP button (➔ 38)

f LISTENING MODE buttons (MOVIE/TV, MUSIC,

GAME and STEREO) (➔ 33 )

g DIMMER button (➔ 26)

h DISPLAY button (➔ 25)

i MUTING button (➔ 26)

j VOL q/w button (➔ 25)

k VIDEO button (➔ 26)

l RETURN button

m^*3

m AUDIO button (➔ 26)

n SLEEP button (➔ 26)

■ Controlling the tuner

To control the AV receiver’s tuner, press TUNER (or

RECEIVER).

You can select AM or FM by pressing TUNER repeatedly.

a Arrow q/w buttons (➔ 30)

b D.TUN button (➔ 30)

c CH +/– button (➔ 31)

d Number buttons (➔ 30)

To control component, you must first enter remote control

code.

See “Entering Remote Control Codes” for more details

(➔ 61).

This button acts as a shortcut for the Video menu (➔ 26).

This button acts as a shortcut for the Audio menu (➔ 26).

Download from Www.Somanuals.com. All Manuals Search And Download.

About Home Theater

Enjoying Home Theater

Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your

own home—just like being in a movie theater or concert hall. With Blu-ray Discs or DVDs, you can enjoy DTS and

Dolby Digital. With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP lis-

tening modes.

a b Front speakers (SKF-680/780)

These output the overall sound. Their role in a home theater is to pro-

vide a solid anchor for the sound image. They should be positioned

facing the listener at about ear level, and equidistant from the TV.

Angle them inward so as to create a triangle, with the listener at the

apex.

Speaker illustrations are based on HTP-680.

Center speaker (SKC-680/780)

This speaker enhances the front speakers, making sound movements

distinct and providing a full sound image. In movies it’s used mainly

for dialog. Position it close to your TV facing forward at about ear

level, or at the same height as the front speakers.

d e Surround speakers (SKR-680/780)

These speakers are used for precise sound positioning and to add real-

istic ambience. Position them at the sides of the listener, or slightly

behind, about 2 to 3 feet (60 to 100 cm) above ear level. Ideally they

should be equidistant from the listener.

Subwoofer (SKW-770/780)

The subwoofer handles the bass sounds of the LFE (Low-Frequency

Effects) channel. The volume and quality of the bass output from your

subwoofer will depend on its position, the shape of your listening

room, and your listening position. In general, a good bass sound can be

obtained by installing the subwoofer in a front corner, or at one-third

the width of the wall, as shown.

g h Surround back speakers (SKB-680/780)

These speakers are necessary to enjoy Dolby Digital EX, DTS-ES

Matrix, DTS-ES Discrete, etc. They enhance the realism of surround

sound and improve sound localization behind the listener. Position

them behind the listener about 2 to 3 feet (60 to 100 cm) above ear

level.

Corner

position

i j Front high speakers (Optional)

These speakers are necessary to enjoy Dolby Pro Logic IIz Height.

They significantly enhance the spatial experience. Position them at

least 3.3 feet (100 cm) above the front speakers (preferably as high as

possible) and at an angle slightly wider than the front speakers.

1/3 of wall

position

Tip

• To find the best position for your subwoofer, while

playing a movie or some music with good bass,

experiment by placing your subwoofer at various

positions within the room, and choose the one that

provides the most satisfying results.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connecting the AV Receiver

Attaching the Speaker Bases

Wall Mounting

■ SKF-780

The speakers can easily be wall mounted by using the key-

hole slots.

Before you connect the speakers, attach the supplied

speaker base to each SKF-780.

Front, Surround and Surround Back

Speakers

1. Turn the speaker upside down with the protection

cover attached.

2. Align the speaker base while the arrow mark

To mount the front, surround and surround back speakers

vertically, use the keyhole slot shown to hang each speaker

on a screw that’s securely screwed into the wall.

headed in the same direction as the speaker’s face.

Be careful not to tip over the speaker.

3. Align the screw holes on the speaker base with those

on the bottom of each speaker, and affix the speaker

base using the supplied screws. Recommended torque

is 10 kgf·cm (9 lbf·in).

■ SKF-680, SKR-680, SKB-680

To prevent the speaker from vibrating against the wall,

attach two of the supplied rubber stoppers to the rear of

each speaker.

Be careful not to tip over the speaker.

4. Turn the speaker right side up.

5. Remove the protection cover.

Top of SKF-780

Protection cover

Keyhole slot for

wall mounting

Rubber stoppers

Supplied screws

Arrow mark

■ SKR-780,SKB-780

Speaker base

Keyhole slot for

wall mounting

Bottom of SKF-780

Center Speaker

To mount the center speaker horizontally, use the two key-

hole slots shown to hang each speaker on two screws that

are securely screwed into the wall.

■ SKC-680

To prevent the speaker from vibrating against the wall,

attach two of the supplied rubber stoppers to the rear of

each speaker.

SAFETY PRECAUTIONS:

• Attach the speaker bases in a manner that will not

allow the speakers to tip over.

Keyhole slot for wall mounting

• Be sure to tighten the screws when you attach the

speaker bases.

• Attach the speaker bases on a flat, level, and stable

floor.

• After you attach the speaker bases, make sure that

the speakers stand upright and are stable.

Rubber

stoppers

8-1/4" (210 mm)

Download from Www.Somanuals.com. All Manuals Search And Download.

■ SKC-780

Using the Stoppers for a More Stable

Platform

Keyhole slot for wall mounting

We recommend using the provided stoppers to achieve the

best possible sound from your speakers. The stoppers pre-

vent the speakers from moving, providing a more stable

platform.

■ SKF-680, SKR-680, SKB-680, SKC-680

Use rubber stoppers for the speakers.

7-7/8" (200 mm)

Rubber stoppers

Caution

• A mounting screw’s ability to support a speaker depends

on how well it’s anchored to the wall. If you have hollow

walls, screw each mounting screw into a stud. If there are

no studs, or the walls are solid, use suitable wall anchors.

• Use screws with a head diameter of 5/16" (8 mm) or less

and a shank diameter of 1/8" (4 mm) or less. With hol-

low walls, use a cable/pipe detector to check for any

power cables or water pipes before making any holes.

• (HTP-680) Leave a gap of between 5/32" (4 mm) and

5/16" (8 mm) between the wall and the base of the screw

head, as shown.

1-3/16" (30 mm)

Bottom of the

SKF-680/

SKR-680/

SKB-680

Bottom of the

SKC-680

1-9/16"

(40 mm)

■ SKC-780

Use cork stoppers for the center speaker.

(HTP-780) Leave a gap of between 3/16" (5 mm) and

7/16" (10 mm) between the wall and the base of the

screw head, as shown.

Cork stoppers

(We recommend that you consult a home installation

professional.)

Wall

Bottom of the

SKC-780

(HTP-680) 5/32" to 5/16"(4 mm to 8 mm)

(HTP-780) 3/16" to 7/16"(5 mm to 10 mm)

Using the Floor Pads for Subwoofer

If the subwoofer is placed on a hard floor (wood, vinyl,

tile, etc.) and playback is very loud, the subwoofer’s feet

may damage the flooring. To prevent this, place the sup-

plied pads underneath the subwoofer’s feet. The pads also

provide a stable base for the subwoofer.

Pad

Download from Www.Somanuals.com. All Manuals Search And Download.

• Make sure the metal core of the wire does not have con-

tact with the AV receiver’s rear panel. Doing so may

damage the AV receiver.

Connecting Your Speakers

Speaker Configuration

The following table indicates the channels you should use

depending on the number of speakers that you have.

For 7.1-channel surround-sound playback, you need

7 speakers and a powered subwoofer.

Number of speakers

Front speakers

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

Center speaker

✔

✔ ✔ ✔ ✔ ✔ ✔

Surround speakers

✔ ✔ ✔ ✔ ✔ ✔ ✔

*1*2

Surround back speaker

✔

Surround back speakers

✔

*2*3

Front high speakers

✔ ✔ ✔

If you’re using only one surround back speaker, connect it to

the SURR BACK OR FRONT HIGH L terminals.

Front high and surround back speakers cannot be used at the

same time.

When you connect the front high left and right speakers, pre-

pare for it separately, or use the surround back left and right

speakers.

No matter how many speakers you use, a powered sub-

woofer is recommended for a really powerful and solid

bass.

To get the best from your surround sound system, you

need to set the speaker settings. You can do this automati-

cally (➔ 28) or manually (➔ 40).

• Don’t connect more than one cable to each speaker ter-

minal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between

6 and 16 ohms. If you use speakers with a lower imped-

ance, and use the amplifier at high volume levels for a

long period of time, the built-in amp protection circuit

may be activated.

• Disconnect the power cord from the wall outlet before

making any connections.

• Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals only to positive (+)

terminals, and negative (–) terminals only to negative (–)

terminals. If you get them the wrong way around, the

sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may

affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires.

Doing so may damage the AV receiver.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Speaker Cables

Screw-type speaker terminals

Strip 1/2" to 5/8" (12 to 15 mm) of

insulation from the ends of the

1/2" to 5/8"(12 to 15 mm)

speaker cables, and twist the bare

wires tightly, as shown. (Supplied

speaker cables are already stripped.)

Using Banana Plugs

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.

• Do not insert the speaker code directly into the center hole of the speaker terminal.

Push-type speaker terminals

Strip 3/8" to 1/2" (10 to 12 mm) of insulation from the ends of

the speaker cables, and twist the bare wires tightly, as shown.

(Supplied speaker cables are already stripped.)

3/8" to 1/2"(10 to 12 mm)

The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one

surround back speaker, connect it to the SURR BACK OR FRONT HIGH L terminals.

Speaker illustrations are based on HTP-680.

Surround

back right

speaker

Surround

back left

speaker

Surround

right

speaker

Surround

left

speaker

Front right Front left

speaker speaker

Center speaker

Tan

Brown

Gray

Blue

Red

White

Green

Front high

right

Front high

left

speaker

(Optional)

speaker

(Optional)

Powered

subwoofer

Using the supplied RCA cable, connect the subwoofer’s LINE INPUT jack to your AV receiver’s SUBWOOFER PRE OUT jack.

Note

• The front high speakers can also be connected to the SURR BACK OR FRONT HIGH SPEAKERS terminals. When doing so, set

“Surr Back/Front High” in Speaker Setup to “Front High” (➔ 40).

Download from Www.Somanuals.com. All Manuals Search And Download.

About AV Connections

Connected image with AV components

HDMI cable

Other cables

: Video & Audio

: Video

: Audio

AV receiver

Blu-ray Disc/

DVD player

Blu-ray Disc/

DVD player

Game console

TV, projector, etc.

• Before making any AV connections, read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunc-

tions).

Right!

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

Wrong!

AV Cables and Jacks

Signal

Cable

Jack

Description

Video and

Audio

HDMI

HDMI connections can carry digital video and audio.

HDMI

Video

Component video

Component video separates the luminance (Y) and color

difference signals (PB/CB, PR/CR), providing the best pic-

ture quality (some TV manufacturers label their compo-

nent video sockets slightly differently).

Green

P^B/CB

PR/CR

Blue

Red

Composite video

Composite video is commonly used on TVs, VCRs, and

See also:

• “Controlling Other Components” (➔ 60)

• “Controlling iPod” (➔ 56)

• “Listening to the Radio” (➔ 30)

• Alternatively, you can use the AV receiver’s DISPLAY.

The following information can typically be displayed.

Input source &

volume^*1

To adjust the volume, use the MASTER VOLUME

control.

Signal format^*2

or sampling

frequency

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (➔ 33)

• “Audyssey” (➔ 44)

Input & output

resolution

■ Operating with the remote controller

Input source &

listening mode^*3

Press RECEIVER followed by INPUT SELEC-

TOR.

Start playback on the source component.

See also:

• “Controlling Other Components” (➔ 60)

• “Controlling iPod” (➔ 56)

• “Listening to the Radio” (➔ 30 )

When AM or FM radio is used, the band, preset number, and

frequency are displayed.

If the input signal is analog, no format information is dis-

played. If the input signal is PCM, the sampling frequency is

displayed. If the input signal is digital but not PCM, the signal

format is displayed.

Information is displayed for about three seconds, then the pre-

viously displayed information reappears.

The input source is displayed with the default name even

when you have entered a custom name in “Name Edit”

(➔ 45).

To adjust the volume, use VOL q/w.

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (➔ 33)

• “Audyssey” (➔ 44)

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Music Optimizer

Selecting Speaker Layout

The Music Optimizer function enhances the sound quality

of compressed music files.

You can prioritize which speakers you want to use.

Press RECEIVER followed by SP LAYOUT

repeatedly.

Press MUSIC OPTIMIZER on the front panel.

The M.Opt indicator lights on the display.

`Speaker Layout:FH:

The sound from front high speakers is output

by priority.

`Speaker Layout:SB:

Tip

• Alternatively, you can use the remote controller’s AUDIO and

arrow buttons.

• See “Music Optimizer” for more details (➔ 51).

The sound from surround back speakers is out-

put by priority.

Note

Setting the Display Brightness

• If the Powered Zone 2 is being used (➔ 54), this setting cannot

be selected.

• When the listening mode that doesn’t support front high or sur-

round back speakers is used, the setting cannot be selected.

You can adjust the brightness of the AV receiver’s display.

Press RECEIVER followed by DIMMER repeat-

edly to select: dim, dimmer, or normal brightness.

Using the Audio and Video Menus

Tip

By pressing AUDIO or VIDEO, you can have a quick

access to frequently used menus without having to go

through the long standard menu. The menus enable you to

change settings and view the current information.

• Alternatively, you can use the AV receiver’s DIMMER.

Muting the AV Receiver

Press RECEIVER followed by AUDIO or VIDEO.

Either of the following screens will be superimposed

on the TV screen.

You can temporarily mute the output of the AV receiver.

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator

flashes on the display.

BD/DVD

Audio

Bass

0dB

Video

Treble

Info

Subwoofer Level

Center Level

Dynamic EQ

Dynamic Volume

Tip

Input Sel

Listening Mode

• To unmute, press MUTING again or adjust the volume.

• The Mute function is cancelled when the AV receiver is set to

Standby.

BD/DVD

Audio

Wide Mode

Picture Mode

Video

Using the Sleep Timer

Info

Auto

Input Sel

Listening Mode

With the sleep timer, you can set the AV receiver to turn

off automatically after a specified period.

Press RECEIVER followed by SLEEP repeatedly

to select the required sleep time.

The sleep time can be set from 90 to 10 minutes in

10 minute steps.

The SLEEP indicator lights on the display when the

sleep timer has been set. The specified sleep time

appears on the display for about 5 seconds, then the

previous display reappears.

Tip

• If you need to cancel the sleep timer, press SLEEP repeatedly

until the SLEEP indicator goes off.

• To check the time remaining until the AV receiver sleeps, press

SLEEP. Note that if you press SLEEP while the sleep time is

being displayed, you’ll shorten the sleep time by 10 minutes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Use q/w/e/r to make the desired selection.

Changing the Input Display

■ Audio

When you connect an u-capable Onkyo component, you

must configure the input display so that u can work

properly.

`You can change the following settings: “Bass”,

“Treble”, “Subwoofer Level ”, “Center Level”,

“Dynamic EQ ”, “Dynamic V o lume ”, “Late

Night”, “Music Optimizer”, “Cinema filter”

and “Audio Selector”.

This setting can be done only from the front panel.

Press TV/CD, GAME or VCR/DVR so that “TV/

CD”, “GAME” or “VCR/DVR” appears on the

display.

See also:

• “Audyssey” (➔ 44)

• “Using the Audio Settings” (➔ 50)

■ Video

`You can change the following settings: “Wide

Mode” and “Picture Mode”.

See also:

• “Picture Adjust” (➔ 46)

*3*4

■ Info

Press and hold down TV/CD, GAMEor VCR/DVR

`You can view the information of the following

items: “Audio”, “Video” and “Tuner”.

(about 3 seconds) to change the input display.

Repeat this step to select “MD”, “CDR”, “DOCK”

or “TAPE”.

*4*5

■ Input Sel

`You can select the input source while viewing

the information as follows: the name of input

selectors, input assignments, and radio informa-

tion, and ARC function setting.

Press ENTER to display the current input

source, followed by q/w to select the desired

input source. Pressing ENTER again switches to

the selected input source.

For the TV/CD input selector, the input display

changes in this order:

TV/CD → MD → CDR

→

TAPE

DOCK

For the GAME input selector, the setting changes in

this order:

GAME ↔ DOCK

■ Listening Mode

For the VCR/DVR input selector, the setting

changes in this order:

`You can select the listening modes that are

grouped in the following categories: “MOVIE/

TV”, “MUSIC” and “GAME”.

VCR/DVR ↔ DOCK

Use q/w to select the category and e/r to

select the listening mode. Press ENTER to

switch to the selected listening mode.

Note

• DOCK can be selected for the TV/CD, GAME or VCR/DVR

input selector, but not at the same time.

• Enter the appropriate remote control code before using the

remote controller for the first time (➔ 60).

Note

If Direct listening mode is selected, “Dynamic EQ” and

“Dynamic Volume” cannot be selected.

Only when you have selected “Custom” in the “Picture

Mode” (➔ 46 ), pressing ENTER allows you to adjust the fol-

lowing items; “Brightness”, “Contrast”, “Hue”, and “Satu-

ration”. Press RETURN to return to the original Video menu.

Depending on the input source and listening mode, not all

channels shown here output the sound.

When you have entered a custom name in “Name Edit”

(➔ 45), the input source is displayed with that name. But

even if not, the component name may be displayed if the AV

receiver receives it via HDMI connection (➔ 19).

For the PORT input selector, the name of Universal Port

Option Dock will be displayed.

Using Headphones

Connect a pair of stereo headphones with a stan-

dard plug (1/4 inch or 6.3 mm) to the PHONES

jack.

Note

• Always turn down the volume before connecting your head-

phones.

• While the headphones plug is inserted in the PHONES jack, the

speakers are turned off. (The Powered Zone 2 speakers are not

turned off.)

• When you connect a pair of headphones, the listening mode is

set to Stereo, unless it’s already set to Stereo, Mono or Direct.

• Only the Stereo, Direct and Mono listening modes can be used

with headphones.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note

Audyssey 2EQ^®Room Correction and

Speaker Setup

• Make the room as quiet as possible. Background noise and Radio

Frequency Interference (RFI) can disrupt the room measure-

ments. Close windows, televisions, radios, air conditioners, flu-

orescent lights, home appliances, light dimmers, or other

devices. Turn off the cell phone (even if it is not in use) or place

it away from all audio electronics.

• The microphone picks up test tones which played through each

speaker as Audyssey 2EQ Room Correction and Speaker Setup

run.

With the supplied calibrated microphone, Audyssey 2EQ

automatically determines the number of speakers con-

nected, their size for purposes of bass management, opti-

mum crossover frequencies to the subwoofer (if present),

and distances from the primary listening position.

Audyssey 2EQ then removes the distortion caused by

room acoustics by capturing room acoustical problems

over the listening area in both the frequency and time

domain. The result is clear, well-balanced sound for every-

one. Enabling Audyssey 2EQ allows you to also use

• Audyssey 2EQ Room Correction and Speaker Setup cannot be

performed while a pair of headphones is connected.

Turn on the AV receiver and the connected TV.

On the TV, select the input to which the AV receiver

is connected.

Audyssey Dynamic EQ , which maintains the proper

octave-to-octave balance at any volume level (➔ 44).

Before using this function, connect and position all of

your speakers.

If “Dynamic EQ” is set to “On” (➔ 44), the “Equalizer”

setting will be set to “Audyssey” (➔ 42). On the other

hand, if it is set to “Off”, the “Dynamic Volume” setting

will be set to “Off” (➔ 44).

It takes about 15 minutes to complete Audyssey 2EQ

Room Correction and Speaker Setup for 3 positions. Total

measurement time varies depending on the number of

speakers.

Set the speaker setup microphone at the Main Lis-

tening Position a, and connect it to the SETUP

MIC jack.

SETUP MIC jack

Speaker setup

microphone

Using Audyssey 2EQ

The speaker setting menu appears.

Using Audyssey 2EQ to create a listening environment in

your home theater that all listeners will enjoy,

Note

• The on-screen setup menus appear only on a TV that is

connected to the HDMI OUT. If your TV is connected to

the MONITOR OUT V or the COMPONENT VIDEO

OUT, use the AV receiver’s display when changing set-

tings.

Audyssey 2EQ takes measurements at up to 3 positions

within the listening area. Position the microphone at ear

height of a seated listener with the microphone tip pointed

directly at the ceiling using a tripod. Do not hold the

microphone in your hand during measurements as this will

produce inaccurate results.

When you’ve finished making the settings, press

ENTER.

a First measurement position

Also referred to as the Main Listening Position this

refers to the most central position where one would

normally sit within the listening environment. 2EQ

uses the measurements from this position to calculate

speaker distance, level, polarity, and the optimum

crossover value for the subwoofer.

2EQ: Auto Setup

Speaker Terminal Assign

Front High/Zone2

SurrBack/Front High

Front High

Surr Back

Press ENTER.

Audyssey 2EQ Room Correction and Speaker Setup

starts.

b Second measurement position

The right side of the listening area.

c Third measurement position

Test tones are played through each speaker as

Audyssey 2EQ Room Correction and Speaker Setup

runs. This process takes a few minutes. Please

refrain from talking during measurements and do

not stand between speakers and the microphone.

Do not disconnect the speaker setup microphone

during Audyssey 2EQ Room Correction and

Speaker Setup, unless you want to cancel the setup.

The left side of the listening area.

The distances from position a to b and a to c must be

at least 1 meter.

Place the setup microphone at the next position,

and then press ENTER.

Audyssey 2EQ performs more measurements. This

takes a few minutes.

cab

When prompted, repeat step 5.

: Listening area

a to c: Listening position

Download from Www.Somanuals.com. All Manuals Search And Download.

The options are:

`Retry:

Try again.

`Cancel:

Cancel Audyssey 2EQ Room Correction and

Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of

the noise and try again.

Use q/w to select an option, and then press

ENTER.

2EQ: Auto Setup

- - Review Speaker Configuration - -

Subwoofer

Front

Center

Surround

Front High

Surr Back

Surr Back Ch

Yes

40Hz

100Hz

120Hz

2ch

• Speaker Matching Error!

Save

Cancel

The number of speakers detected was different from

that of the first measurement. Check the speaker con-

nection.

The options are:

`Save:

• Writing Error!

Save the calculated settings and exit

Audyssey 2EQ^®Room Correction and Speaker

Setup.

This message appears if saving fails. Try saving again.

If this message appears after 2 or 3 attempts, contact

your Onkyo dealer.

• Speaker Detect Error

This message appears if a speaker is not detected. “No”

means that no speaker was detected.

`Cancel:

Cancel Audyssey 2EQ Room Correction and

Speaker Setup.

Note

Tip

• You can view the calculated settings for the speaker con-

figuration, speaker distances, and speaker levels by using

e/r.

• See “Speaker Configuration” for appropriate settings (➔ 16).

Changing the Speaker Settings Manually

Disconnect the speaker setup microphone.

You can manually make changes to the settings found dur-

ing Audyssey 2EQ Room Correction and Speaker Setup.

See also:

Note

• When Audyssey 2EQ Room Correction and Speaker Setup is

complete, the “Equalizer” will be set to “Audyssey” (➔ 42).

The Audyssey indicator will light (➔ 9).

• You can cancel Audyssey 2EQ Room Correction and Speaker

Setup at any point in this procedure simply by disconnecting the

setup microphone.

• “Speaker Configuration” (➔ 41)

• “Speaker Distance” (➔ 41)

• “Level Calibration” (➔ 42)

• “Equalizer Settings” (➔ 42)

Using a Powered Subwoofer

• Do not connect or disconnect any speakers during

Audyssey 2EQ Room Correction and Speaker Setup.

• If the AV receiver is muted, it will be unmuted automatically

when Audyssey 2EQ Room Correction and Speaker Setup starts.

• Changes to the room after Audyssey 2EQ Room Correction and

Speaker Setup requires you run Audyssey 2EQ Room Correc-

tion and Speaker Setup again, as room EQ characteristics may

have changed.

If you’re using a powered subwoofer and it outputs very

low-frequency sound at a low volume level, it may not be

detected by Audyssey 2EQ Room Correction and Speaker

Setup.

If the “Subwoofer” appears on the “Review Speaker

Configuration” screen as “No”, increase the subwoofer’s

volume to the half-way point, set it to its highest crossover

frequency, and then try running Audyssey 2EQ Room

Correction and Speaker Setup again. Note that if the vol-

ume is set too high and the sound distorts, detection issues

may occur, so use an appropriate volume level.

Error Messages

While Audyssey 2EQ Room Correction and Speaker

Setup is in progress, one of the error messages below may

appear.

2EQ: Auto Setup

Ambient noise is too high.

Retry

Cancel

Error message

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio

■ Manual tuning mode

This section describes the procedure using the but-

tons on the front panel unless otherwise specified.

Press TUNING MODEso that the AUTO indicator

goes off on the display.

Using the Tuner

Press and hold TUNING q/w.

The frequency stops changing when you release the

button.

With the built-in tuner you can enjoy AM and FM radio

stations. You can store your favorite stations as presets for

quick selection.

This model changes FM/AM frequency in 200/10kHz (or

50/9kHz) steps.

Press the buttons repeatedly to change the frequency

one step at a time.

In manual tuning mode, FM stations will be in mono.

Listening to the Radio

Tuning into weak FM stereo stations

If the signal from a stereo FM station is weak, it may be

impossible to get good reception. In this case, switch to

manual tuning mode and listen to the station in mono.

Press TUNER to select either “AM” or “FM”.

In this example, FM has been selected.

Each time you press TUNER, the radio band

changes between AM and FM.

■ Tuning into stations by frequency

You can tune into AM and FM stations directly by enter-

ing the appropriate frequency.

Band

Frequency

On the remote controller, press TUNER repeat-

edly to select “AM” or “FM”, followed by D.TUN.

(Actual display depends on the country.)

Tuning into Radio Stations

■ Auto tuning mode

(Actual display depends on the country.)

Within 8 seconds, use the number buttons to enter

the frequency of the radio station.

For example, to tune to 87.50 (FM), press 8, 7, 5, 0.

If you have entered the wrong number, you can retry

after 8 seconds.

Press TUNING MODE so that the AUTO indicator

lights on the display.

Press TUNING q/w.

Searching stops when a station is found.

When tuned into a station, the TUNED indicator lights.

When tuned into a stereo FM station, the FM STEREO

indicator lights on the display, as shown.

FM STEREO

AUTO

TUNED

Download from Www.Somanuals.com. All Manuals Search And Download.

Presetting FM/AM Stations

You can store a combination of up to 40 of your favorite

FM/AM radio stations as presets.

Tune into the FM/AM station that you want to

store as a preset.

See the previous section.

Press MEMORY.

The preset number flashes.

While the preset number is flashing (about 8 sec-

onds), use PRESET e/r to select a preset from 1

through 40.

Press MEMORY again to store the station or chan-

nel.

The station or channel is stored and the preset num-

ber stops flashing.

Repeat this procedure for all of your favorite FM/

AM radio stations.

Note

• You can name your radio presets for easy identification (➔ 45).

Its name is displayed instead of the band and frequency.

Selecting Presets

To select a preset, use PRESET e/r on the AV

receiver, or the remote controller’s CH +/–.

Tip

• You can also use the remote controller’s number buttons to select

a preset directly.

Deleting Presets

Select the preset that you want to delete.

See the previous section.

While holding down MEMORY, press TUNING

MODE.

The preset is deleted and its number disappears from

the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording

This section explains how to record the selected input source to a component with recording capability, and how to record

audio and video from different sources.

Connecting a Recording Component

Recording Separate AV Sources

Here you can record audio and video from completely

separate sources, allowing you to overdub audio onto your

video recordings. This function takes advantage of the fact

that when an audio-only input source (TV/CD) is selected,

the video input source remains unchanged.

In the following example, audio from the CD player con-

nected to the TV/CD IN and video from the camcorder

connected to the AUX INPUT VIDEO jack are recorded

by the VCR connected to the VCR/DVR OUT jacks.

AUDIO

VIDEO

Camcorder

VCR,

DVD recorder

Cassette, CDR,

MD, etc.

Note

• The AV receiver must be turned on for recording. Recording is

not possible while it’s in Standby mode.

• If you want to record directly from your TV or playback VCR to

the recording VCR without going through the AV receiver, con-

nect the TV/VCR’s audio and video outputs directly to the

recording VCR’s audio and video inputs. See the manuals sup-

plied with your TV and VCR for details.

• Video signals connected to composite video inputs can be

recorded only via composite video outputs. If your TV/VCR is

connected to a composite video input, the recording VCR must

be connected to a composite video output.

• The surround sound and DSP listening modes cannot be

recorded.

• Copy-protected Blu-ray Disc/DVDs cannot be recorded.

• Sources connected to a digital input cannot be recorded. Only

analog inputs can be recorded.

• DTS signals will be recorded as noise, so don’t attempt analog

recording of DTS CDs or LDs.

CD player

VCR

: Video signal

: Audio signal

AV Recording

Prepare the camcorder and CD player for play-

back.

Audio sources can be recorded to a recorder (e.g., cassette

deck, CDR, MD) connected to the VCR/DVR OUT jacks.

Video sources can be recorded to a video recorder (e.g.,

VCR, DVD recorder) connected to the VCR/DVR OUT

jack.

Prepare the VCR for recording.

Press AUX input selector.

Press TV/CD input selector.

This selects the CD player as the audio source, but

leaves the camcorder as the video source.

Use the input selector buttons to select the source

that you want to record.

You can watch the source while recording. The AV

receiver’s MASTER VOLUME control has no effect

on recording.

Start recording on the VCR and start playback on

the camcorder and CD player.

The video from the camcorder and the audio from

the CD player are recorded by the VCR.

On your recorder, start recording.

On the source component, start playback.

If you select another input source during recording,

that input source will be recorded.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Listening Modes

Selecting Listening Modes

See “About Listening Modes” for detailed information about the listening modes (➔ 34).

Listening Mode Buttons

Press RECEIVER first.

MOVIE/TV, MUSIC, GAME

MUSIC

GAME

MOVIE/TV

STEREO

MOVIE/TV button

This button selects the listening modes intended for use

with movies and TV.

MUSIC button

This button selects the listening modes intended for use

with music.

GAME button

This button selects the listening modes intended for use

with video games.

STEREO button

This button selects Stereo and All Channel Stereo lis-

tening modes.

• The Dolby Digital and DTS listening modes can only be selected if your Blu-ray Disc/DVD player is connected to the AV

receiver with a digital audio connection (coaxial, optical, or HDMI).

• The listening modes you can select depends on the format of the input signal. To check the format, see “Displaying Source

Information” (➔ 25).

• While a pair of headphones is connected, you can select the following listening modes: Mono, Direct, and Stereo.

• The listening modes cannot be used while you are listening to sound through your TV speakers coming from components

connected to the AV receiver (“TV Sp On” appears on the front panel).

Download from Www.Somanuals.com. All Manuals Search And Download.

About Listening Modes

The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidel-

ity and stunning surround sound.

Explanatory Notes

Speaker illustrations are based on HTP-680.

SP LAYOUT

LISTENING MODE

a b Front speakers

Center speaker

d e Surround speakers

Subwoofer

g h Surround back speakers

i j Front high speakers

■ Input Source

The following audio formats are supported by the listening mode.

This is mono (monophonic) sound.

This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two

speakers.

This is 5.1-channel surround sound. This surround system has five main channels of sound and a sixth sub-

woofer channel (called the point-one channel).

This is 7.1-channel surround sound. This is a further sound enhancement to 5.1 channel sound with two

additional speakers that provide greater sound envelopment and more accurate positioning of sounds.

This is DTS-ES surround sound. This surround system can produce a discrete or a matrix-encoded sixth

channel from existing DTS 5.1 encoded material.

This is Dolby Digital EX surround sound. This provides a center back surround channel from 5.1-channel

sources.

■ Speaker Layout

The illustration shows which speakers are activated in each channel. See “Speaker Configuration” for the speaker setup

(➔ 41).

Press RECEIVER followed by SP LAYOUT

repeatedly to select front high or surround

back speakers.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening Modes

Listening Mode

Description

Input

Source

Speaker

Layout

Direct

In this mode, audio from the input source is output without surround-sound

processing. The “Sp Config” (presence of speakers), “Sp Distance” and

“A/V Sync” settings are enabled, but much of the processing set via AUDIO

is disabled. See “Advanced Setup” for more details (➔ 38).

ZXC

D i r e c t d i o P P

Stereo

Sound is output by the front left and right speakers and subwoofer.

ZXC

S t e r e o d i o P P

Mono

Use this mode when watching an old movie with a mono soundtrack, or use

it with the foreign language soundtracks recorded in the left and right chan-

nels of some movies. It can also be used with DVDs or other sources contain-

ing multiplexed audio, such as karaoke DVDs.

M o n o e o d i o P P

Multichannel

This mode is for use with PCM multichannel sources.

XCN

M u l t i c h i o P P

Dolby Pro Logic IIx^*2Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel play-

Dolby Pro Logic II

back. It provides a very natural and seamless surround-sound experience that

fully envelops the listener. As well as music and movies, video games can

also benefit from the dramatic spatial effects and vivid imaging. If you’re not

using any surround back speakers, Dolby Pro Logic II will be used instead

of Dolby Pro Logic IIx.

• Dolby PLIIx Movie

Use this mode with any stereo or Dolby Surround (Pro Logic) movie (e.g.,

TV, DVD, VHS).

• Dolby PLIIx Music

Use this mode with any stereo or Dolby Surround (Pro Logic) music source

(e.g., CD, radio, cassette, TV, VHS, DVD).

• Dolby PLIIx Game

Use this mode with video games, especially those that bear the Dolby Pro

Logic II logo.

P L b M o v i e P P

P L b M u s i c P P

P L b G a m e c P P

P L x GM o v i e P

P L x GM u s i c P

P L x GG a m e c P

• Dolby PLIIx Movie and Dolby PLIIx Music

These modes use the Dolby Pro Logic IIx modes to expand 5.1-channel

sources for 7.1-channel playback.

Dolby Pro Logic IIz

Height

Dolby Pro Logic IIz Height is designed to more effectively use existing

program material when height channel speaker outputs are present. Dolby

Pro Logic IIz Height can be used to upmix a variety of sources from movies

and music, but are particularly well-suited to upmix game content.

P L z GH e i g h t

Dolby EX

These modes expand 5.1-channel sources for 6.1/7.1-channel playback.

They’re especially suited to Dolby EX soundtracks that include a matrix-

encoded surround back channel. The additional channel adds an extra dimen-

sion and provides an enveloping surround sound experience, perfect for

rotating and fly-by sound effects.

D o l b y c E X o P P

D o l b y c D i E X P

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening Mode

Dolby Digital

Description

Input

Source

Speaker

Layout

In this mode, audio from the input source is output without surround-sound

processing. “Sp Config” (presence of speakers), “Crossover”, “Sp Dis-

tance”, “A/V Sync” and much of the processing set via AUDIO are enabled.

See “Advanced Setup” for more details (➔ 38).

XCN

D o l b y c D i o P P

Dolby Digital Plus^*5

XCN

D o l b y c D o P P

Dolby TrueHD

XCN

D D Tl r u e H D P P

DTS

XCN

D T S

d i o P P

DTS-HD High

Resolution Audio

XCN

D T S – H D H R

DTS-HD Master

Audio

XCN

D T S – H D MS T R

DTS Express

XCN

D T S E x p r e s s

DSD^*6

D S D

DTS 96/24^*7

This mode is for use with DTS 96/24 sources. This is high-resolution DTS

with a 96 kHz sampling rate and 24-bit resolution, providing superior fidel-

ity. Use it with DVDs that bear the DTS 96/24 logo.

D T S e 9 6 / 2 4 P P

DTS-ES Discrete^*8

This mode is for use with DTS-ES Discrete soundtracks, which use a dis-

crete surround back channel for true 6.1/7.1-channel playback. The seven

totally separate audio channels provide better spatial imaging and 360-

degree sound localization, perfect for sounds that pan across the surround

channels. Use it with DVDs that bear the DTS-ES logo, especially those with

a DTS-ES Discrete soundtrack.

E S S D i s c r e t e

DTS-ES Matrix^*8

This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-

encoded back-channel for 6.1/7.1-channel playback. Use it with DVDs that

bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.

E S SM a t r i x t e

DTS Neo:6

This mode expands any 2-channel source for up to 7.1-channel playback. It

uses seven full-bandwidth channels of matrix decoding for matrix-encoded

material, providing a very natural and seamless surround sound experience

that fully envelops the listener.

• Neo:6 Cinema

Use this mode with any stereo movie (e.g., TV, DVD, VHS).

• Neo:6 Music

XCN

N e o : 6 t r i x t e

N e o : 6 Ct ri ni ex mt ae

N e o : 6 t M u s i c

Use this mode with any stereo music source (e.g., CD, radio, cassette, TV,

VHS, DVD).

This mode uses Neo:6 to expand 5.1-channel sources for 6.1/7.1-channel

playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onkyo-Original DSP Listening Modes

Listening Mode

Orchestra

Description

Input

Source

Speaker

Layout

Suitable for classical or operatic music, this mode emphasizes the surround

channels in order to widen the stereo image, and simulates the natural rever-

beration of a large hall.

O r c h e s t r a

Unplugged

Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the

front stereo image, giving the impression of being right in front of the stage.

U n p l u g g e d

Studio-Mix

Suitable for rock or pop music, listening to music in this mode creates a

lively sound field with a powerful acoustic image, like being at a club or rock

concert.

S t u d i o – M i x

TV Logic

This mode adds realistic acoustics to TV shows produced in a TV studio,

surround effects to the entire sound, and clarity to voices.

T V L o g i c

Game-RPG

Use this mode when playing role playing game discs.

Use this mode when playing action game discs.

Use this mode when playing rock game discs.

Use this mode when playing sports game discs.

G a m e – R P G

Game-Action

G a m e – A c t i o n

Game-Rock

G a m e – R o c k

Game-Sports

G a m e – S p o r t s

All Ch Stereo

Ideal for background music, this mode fills the entire listening area with ste-

reo sound from the front, surround, and surround back speakers.

XCN

A l l C h S t

Full Mono

In this mode, all speakers output the same sound in mono, so the sound you

hear is the same regardless of where you are within the listening room.

F u l l M o n o

T-D (Theater-

Dimensional)

With this mode you can enjoy a virtual surround sound even with only two or

three speakers. This works by controlling how sounds reach the listener’s left

and right ears. Good results may not be possible if there’s too much reverb,

so we recommend that you use this mode in an environment with little or no

natural reverb.

ZXC

T – D

Note

When the input source contains the encoded front high channel, front high speakers output the sound.

If there are no surround back speakers, or Powered Zone 2 is being used, Dolby Pro Logic II is used.

Surround back speakers are not supported.

Front high speakers are not supported.

For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system.

AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better

sound according to the player. In that case, set the output setting on the player side to PCM.

Depending on the input source, DTS is used.

If there are no surround back speakers, DTS is used.

Output can be switched between front high or surround back speakers by pressing SP LAYOUT [depending on the “Speaker Con-

figuration” setting (➔ 41)].

• The listening modes cannot be selected with some source formats.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

Advanced Setup

On-screen Setup Menus

Common Procedures in Setup Menu

The on-screen setup menus appear only on a TV that

is connected to the HDMI OUT. If your TV is con-

nected to the composite video MONITOR OUT or the

COMPONENT VIDEO OUT, use the AV receiver’s

display when changing settings.

Remote indicator

RECEIVER

This manual describes the procedure using the

remote controller unless otherwise specified.

ENTER

q/w/e/r

SETUP

RETURN

1. Input/Output Assign

2. Speaker Setup

The on-screen setup menus appear on the connected TV

and provide a convenient way to change the AV receiver’s

various settings. Settings are organized into 9 categories

on the main menu.

3. Audio Adjust

4. Source Setup

5. Listening Mode Preset

6. Miscellaneous

7. Hardware Setup

8. Remote Controller Setup

9. Lock Setup

Carry out the settings by using the on-screen display.

Press RECEIVER followed by SETUP.

The following menu appears.

a Input/Output Assign f Miscellaneous

1. Input/Output Assign

2. Speaker Setup

3. Audio Adjust

4. Source Setup

5. Listening Mode Preset

6. Miscellaneous

7. Hardware Setup

8. Remote Controller Setup

9. Lock Setup

(➔ 39)

(➔ 48)

1. Input/Output Assign

6. Miscellaneous

1. Monitor Out

2. HDMI Input

1. Volume Setup

2. OSD Setup

3. Component Video Input

4. Digital Audio Input

b Speaker Setup

g Hardware Setup

Tip

(➔ 40)

(➔ 48)

• If the main menu doesn’t appear, make sure the appropri-

ate external input is selected on your TV.

2. Speaker Setup

7. Hardware Setup

1. Speaker Settings

2. Speaker Configuration

3. Speaker Distance

4. Level Calibration

5. Equalizer Settings

1. Remote ID

2. Tuner

Use q/w to select a menu, and then press ENTER.

3. HDMI

Use q/w to select target, and then press ENTER.

c Audio Adjust

h Remote Controller

(➔ 42)

Setup (➔ 60)

Use q/w to select option and use e/r to change

the setting.

3. Audio Adjust

8. Remote Controller Setup

Remote Mode Setup

Press SETUP to close the menu.

Press RETURN to return to the previous menu.

1. Multiplex/Mono

2. Dolby

3. DTS

4. Theater-Dimensional

d Source Setup (➔ 44) i Lock Setup (➔ 50)

Note

• This procedure can also be performed on the AV receiver by

using SETUP, arrow buttons, and ENTER.

4. Source Setup

9. Lock Setup

Lock

1. Audyssey

• During Audyssey 2EQ^®Room Correction and Speaker Setup,

messages, etc., that are displayed on the TV screen will appear

in the Display.

2. IntelliVolume

3. A/V Sync

4. Name Edit

5. Picture Adjust

e Listening Mode Preset

(➔ 47)

5. Listening Mode Preset

1. BD/DVD

2. VCR/DVR

3. CBL/SAT

4. GAME

5. AUX

6. TUNER

7. TV/CD

8. PORT

Download from Www.Somanuals.com. All Manuals Search And Download.

Explanatory Notes

Composite video,

component video

HDMI

Main menu

Speaker Setup

■ Subwoofer

`Yes:

Select if a subwoofer is connected.

`No:

Select if no subwoofer is connected.

OUT

Composite video,

component video

Here are the default assignments.

a Menu selection

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

HDMI1

b Setting target

c Setting options (default setting underlined)

HDMI2

HDMI3

Input/Output Assign

HDMI4

AUX

- - - - -

Main Menu

Input/Output Assign

TUNER

TV/CD

- - - - - (Fixed)

- - - - -

Monitor Out

PORT

- - - - -

You can specify the output resolution for the HDMI OUT

and have the AV receiver upconvert the picture resolution

as necessary to match the resolution supported by your

TV.

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD, PORT

`HDMI1, HDMI2, HDMI3, HDMI4:

Select a corresponding HDMI input that the video

component has been connected.

■ Resolution

`Through:

Select this to pass video through the AV receiver at

the same resolution and with no conversion.

`Auto:

`- - - - -:

Select this to output composite video and component

video sources from the HDMI OUT. The video sig-

nal from HDMI output is configured in “Component

Video Input” (➔ 40).

Select this to have the AV receiver automatically

convert video at resolutions not supported by your

TV.

• Each HDMI input cannot be assigned to two input selec-

tors or more. When HDMI1 - HDMI4 have already

been assigned, you must set first any unused input selec-

tors to “- - - - -” or you will be unable to assign HDMI1

- HDMI4 to input selector.

`480p:

Select this for 480p output and video conversion as

necessary.

`720p:

Note

Select this for 720p output and video conversion as

• When an HDMI IN is assigned to an input selector as explained

here, the same HDMI IN will be set as a priority in the “Digital

Audio Input” (➔ 40). In this case, if you want to use the coaxial

or optical audio input, make the selection in the Audio Selector

in the Audio menu (➔ 26).

necessary.

`1080i:

Select this for 1080i output and video conversion as

necessary.

`1080p:

• “TUNER” selector cannot be assigned and is fixed at the

“- - - - -” option.

• If you connect a component (such as UP-A1 Dock that seated

iPod) to UNIVERSAL PORT jack, you cannot assign any input

to “PORT” selector.

• Do not assign the component connected with the HDMI input to

“TV/CD” selector when you set “TV Control” setting to “On”

(➔ 50). Otherwise, appropriate CEC (Consumer Electronics

Control) operation will not be guaranteed.

Select this for 1080p output and video conversion as

necessary.

HDMI Input

If you connect a video component to an HDMI input, you

must assign that input to an input selector. For example, if

you connect your Blu-ray Disc/DVD player to HDMI

IN 2, you must assign “HDMI2” to the “BD/DVD” input

selector.

If you’ve connected your TV to the AV receiver with an

HDMI cable, composite video and component video

sources can be upconverted to HDMI. See “Video Con-

nection Formats” for more information on video signal

flow and upconversion (➔ 23).

Download from Www.Somanuals.com. All Manuals Search And Download.

Component Video Input

Note

• When an HDMI IN is assigned to an input selector in

“HDMI Input” (➔ 39), the same HDMI IN will be set as a prior-

ity in this assignment. In this case, if you want to use the coaxial

or optical audio input, make the selection in the Audio Selector

in the Audio menu.

• Available sampling rate for PCM signals from a digital input

(optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

• If you connect a component (such as UP-A1 Dock that seated

iPod) to the UNIVERSAL PORT jack, you cannot assign any

input to “PORT” selector.

If you connect a video component to a component video

input, you must assign that input to an input selector. For

example, if you connect your Blu-ray Disc/DVD player to

COMPONENT VIDEO IN 2, you must assign “IN2” to

the “BD/DVD” input selector.

Here are the default assignments.

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

IN1

- - - - -

IN2

Speaker Setup

- - - - -

- - - - - (Fixed)

- - - - -

AUX

Main menu

Speaker Setup

TUNER

TV/CD

Some of the settings in this section are set automatically

by Audyssey 2EQ Room Correction and Speaker

PORT

Setup function (➔ 28).

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD, PORT

`IN1, IN2:

Select a corresponding component video input that

the video component has been connected.

`- - - - -:

Here you can check the settings made by Audyssey 2EQ

Room Correction and Speaker Setup function, or set them

manually, which is useful if you change one of the con-

nected speakers after using Audyssey 2EQ Room Correc-

tion and Speaker Setup function.

Note

Select if you are using HDMI output, not component

video output, to output composite video and compo-

nent video sources.

• These settings are disabled when:

– a pair of headphones is connected, or

– the “Audio TV Out” setting is set to “On” ( ➔ 49) and an

input selector other than HDMI is selected.

Note

• If you connect a component (such as UP-A1 Dock that seated

iPod) to the UNIVERSAL PORT jack, you cannot assign any

input to “PORT” selector.

Speaker Settings

Digital Audio Input

If you change these settings, you must run

Audyssey 2EQ Room Correction and Speaker Setup

again (➔ 28).

If you connect a component to a digital audio input, you

must assign that input to an input selector. For example, if

you connect your CD player to the OPTICAL IN 1, you

must assign “OPT1” to the “TV/CD” input selector.

Here are the default assignments.

■ Speaker Terminal Assign

Front High/Zone2

With this setting, you can specify the speakers con-

nected to FRONT HIGH OR ZONE 2 SPEAKERS

terminals.

`Front High:

Front high speakers can be used.

`Zone2:

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

COAX1

- - - - -

COAX2

OPT1

Zone 2 speakers can be used (Powered Zone 2

enabled).

AUX

- - - - -

TUNER

TV/CD

- - - - - (Fixed)

OPT2

SurrBack/Front High

With this setting, you can specify the speakers con-

nected to SURR BACK OR FRONT HIGH SPEAK-

ERS terminals.

`Surr Back:

Surround back speakers can be used.

`Front High:

PORT

- - - - -

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD, PORT

`COAX1, COAX2, OPT1, OPT2:

Select a corresponding digital audio input that the

component has been connected.

`- - - - -:

Front high speakers can be used.

Note

Select if the component is connected to an analog

audio input.

• If “Front High” is selected in the “Front High/Zone2” setting,

you cannot select “Front High” here.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker Configuration

Note

• If the “Surr Back” Setting is set to “None” (➔ 48), this setting

cannot be selected.

This setting is set automatically by Audyssey 2EQ

Room Correction and Speaker Setup function (➔ 28).

■ LPF of LFE

(Low-Pass Filter for the LFE Channel)

`80Hz, 90Hz, 100Hz, 120Hz

With this setting, you can specify the cutoff frequency

of the LFE channel’s low-pass filter (LPF), which can

be used to filter out unwanted hum. The LPF only

applies to sources that use the LFE channel.

With these settings, you can specify which speakers are

connected and a crossover frequency for each speaker.

Specify “Full Band” for speakers that can output low fre-

quency bass sounds adequately, for example, speakers

with a good sized woofer. For smaller speakers, specify a

crossover frequency. Sounds below the crossover fre-

quency will be output by the subwoofer instead of the

speaker. Refer to your speaker’s manuals to determine the

optimum crossover frequencies.

■ Double Bass

This setting is NOT set automatically by Audyssey 2EQ

Room Correction and Speaker Setup function (➔ 28).

■ Subwoofer

`Yes:

With the Double Bass function, you can boost bass out-

put by feeding bass sounds from the front left, right, and

center channels to the subwoofer.

`On:

Select if a subwoofer is connected.

`No:

Select if no subwoofer is connected.

Double Bass function on.

■ Front

`Off:

`Full Band

Double Bass function off.

`40Hz to 100Hz, 120Hz, 150Hz, 200Hz

Note

• This function can be set only if the “Subwoofer” setting is set to

“Yes”, and the “Front” setting is set to “Full Band”.

• If the “Subwoofer” setting is set to “No”, the “Front” setting is

fixed at “Full Band”.

*2*3*4*5

■ Center , Surround , Surr Back

Speaker Distance

`Full Band

`40Hz to 100Hz, 120Hz, 150Hz, 200Hz

`None:

This setting is set automatically by Audyssey 2EQ

Room Correction and Speaker Setup function (➔ 28).

Select if no speaker is connected.

*1*2*4*6

Here you can specify the distance from each speaker to the

listening position so that the sound from each speaker

arrives at the listener’s ears as the sound designer

intended.

■ Front High

`Full Band

`40Hz to 100Hz, 120Hz, 150Hz, 200Hz

`None:

Select if no speaker is connected.

■ Unit

`feet:

Note

Distances can be set in feet. Range: “1ft” to “30ft” in

1 foot steps.

`meters:

“Full Band” can be selected only when “Full Band ” is

selected in the “Front” setting.

If the “Surround” setting is set to “None”, this setting cannot

be selected.

If the “Surround” setting is set to anything other than “Full

Band”, “Full Band” cannot be selected here.

If the Powered Zone 2 is being used (➔ 54), this setting can-

not be selected.

If you have selected other than “Surr Back” in the “Surr-

Back/Front High” setting, this setting cannot be selected.

If you have selected other than “Front High” in the “Front

High/Zone2” or “SurrBack/Front High” setting, this setting

cannot be selected.

Distances can be set in meters. Range: “0.3m” to

“9.0m” in 0.3 meter steps.

■ Left, Front High Left, Center, Front High Right,

Right, Surr Right, Surr Back Right, Surr Back

Left, Surr Left, Subwoofer

`Specify the distance from the each speaker to your lis-

tening position.

Note

• Speakers that you set to “No” or “None” in the

“Speaker Configuration” cannot be selected (➔ 41).

■ Surr Back Ch

`1ch:

Select if only one surround back speaker is con-

nected.

`2ch:

Select if two (left and right) surround back speakers

are connected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Level Calibration

Audio Adjust

Main menu

Audio Adjust

This setting is set automatically by Audyssey 2EQ

Room Correction and Speaker Setup function (➔ 28).

With the Audio Adjust functions and settings, you can

adjust the sound and listening modes as you like.

Here you can adjust the level of each speaker with the

built-in test tone so that the volume of each speaker is the

same at the listening position.

Multiplex/Mono

■ Multiplex

■ Left, Front High Left, Center , Front High Right,

Right, Surr Right, Surr Back Right, Surr Back

Left, Surr Left

`–12dB to 0dB to +12dB in 1 dB step.

This setting determines which channel of a stereo multi-

plex source is output. Use it to select audio channels or

languages with multiplex sources, multilingual TV

broadcasts, and so on.

■ Subwoofer

Input Channel

`Main:

`–15dB to 0dB to +12dB in 1 dB step.

Note

The main channel is output.

• Speakers that you set to “No” or “None” in the

“Speaker Configuration” cannot be selected (➔ 41).

• The speakers cannot be calibrated while the AV receiver is

muted.

`Sub:

The sub channel is output.

`Main/Sub:

Both the main and sub channels are output.

For the center speaker and subwoofer, the level settings made

by using the Audio menu are saved here as the default settings

(➔ 26).

■ Mono

This setting specifies the channel to be used for playing

any 2-channel digital source such as Dolby Digital, or

2-channel analog/PCM source in the Mono listening

mode.

Tip

• If you’re using a handheld sound level meter, adjust the level of

each speaker so that it reads 75 dB SPL at the listening position,

measured with C-weighting and slow reading.

Input Channel

`Left + Right:

Equalizer Settings

Both the left and right channels are output.

`Left:

This setting is set automatically by Audyssey 2EQ

Room Correction and Speaker Setup function (➔ 28).

Only the left channel is output.

`Right:

Only the right channel is output.

■ Equalizer

`Audyssey:

Dolby

This is selected automatically by Audyssey 2EQ

Room Correction and Speaker Setup function. The

Audyssey indicator will light (➔ 9) and

“Dynamic EQ” and “Dynamic Volume” become

available (➔ 44).

■ PLIIx Music (2ch Input)

These settings apply to only 2-channel stereo sources.

If you’re not using any surround back speakers, these

settings apply to Dolby Pro Logic II, not Dolby Pro

Logic IIx.

`Off:

No Audyssey 2EQ equalizing will apply.

Panorama

`On:

Panorama function on.

`Off:

Note

• While the Direct listening mode is selected, this setting has no

effect.

• Audyssey equalizing does not work for DSD sources.

Panorama function off.

With this setting, you can broaden the width of the front

stereo image when using the Dolby Pro Logic IIx Music

listening mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimension

DTS

`–3 to 0 to +3

■ Neo:6 Music

With this setting, you can move the sound field forward

or backward when using the Dolby Pro Logic IIx Music

listening mode. Higher settings move the sound field

backward. Lower settings move it forward.

If the stereo image feels too wide, or there’s too much

surround sound, move the sound field forward to

improve the balance. Conversely, if the stereo image

feels like it’s in mono, or there’s not enough surround

sound, move it backward.

Center Image

`0 to 2 to 5

The DTS Neo:6 Music listening mode creates 6-channel

surround sound from 2-channel stereo sources. With

this setting, you can specify by how much the front left

and right channel output is attenuated in order to create

the center channel.

Setting a value “0” in the middle is set to hear a sound.

Sound is spread in left and right (the outside) so that the

set value is made big. Please adjust by liking.

Center Width

`0 to 3 to 7

With this setting, you can adjust the width of the sound

from the center speaker when using the Dolby Pro

Logic IIx Music listening mode. Normally, if you’re

using a center speaker, the center channel sound is out-

put by only the center speaker. (If you’re not using a

center speaker, the center channel sound will be distrib-

uted to the front left and right speakers to create a phan-

tom center). This setting controls the front left, right,

and center mix, allowing you to adjust the weight of the

center channel sound.

Theater-Dimensional

■ Listening Angle

`Wide:

Select if the listening angle is 40 degrees.

`Narrow:

Select if the listening angle is 20 degrees.

With this setting, you can optimize the Theater-Dimen-

sional listening mode by specifying the angle of the

front left and right speakers relative to the listening

position. Ideally, the front left and right speakers should

be equidistant from the listening position and at an

angle close to one of the two available settings.

■ PLIIz Height Gain

The Height Gain Control in Dolby Pro Logic IIz

enables the listener to select how much gain is applied

to the front high speakers. There are three settings,

“Low”, “Mid” and “High”, and the front high speakers

are accentuated in that order. While “Mid” is the default

listening setting, the listener may adjust the Height Gain

Control to their personal preference.

`Low:

Front left speaker

Front right speaker

20°/40°

Low PLIIz Height Gain becomes active.

`Mid:

Medium PLIIz Height Gain becomes active.

`High:

High PLIIz Height Gain becomes active.

Note

• If the “Front High” settings is set to “None” (➔ 40), this setting

cannot be selected.

■ Dolby EX

This setting determines how Dolby EX encoded signals

are handled. This setting is unavailable if no surround

back speakers are connected. This setting is effective

with Dolby Digital, Dolby Digital Plus and Dolby

TrueHD only.

Dolby EX

`Auto:

If the source signal contains a Dolby EX flag, the

Dolby EX listening mode is used.

`Manual:

You can select any available listening mode.

Note

• If the “Surr Back” setting is set to “None” (➔ 41), this setting

cannot be selected.

• If the “Front High” setting is enabled (➔ 40), this setting is

fixed at “Manual”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Audyssey Dynamic EQ is referenced to the standard

film mix level. It makes adjustments to maintain the ref-

erence response and surround envelopment when the

volume is turned down from 0 dB. However, film refer-

ence level is not always used in music or other non-film

content. Audyssey Dynamic EQ Reference Level Offset

provides three offsets from the film level reference

(5 dB, 10 dB, and 15 dB) that can be selected when the

mix level of the content is not within the standard.

Source Setup

Items can be set individually for each input selector.

Preparation

Press the input selector buttons to select an input source.

Main menu

Source Setup

Note

Audyssey

• If “Dynamic EQ” setting is set to “Off”, this setting cannot be

selected.

When Audyssey 2EQ Room Correction and Speaker

Setup is complete, the “Equalizer” setting (➔ 42) will be

set to “Audyssey” and the “Dynamic EQ” will be set to

“On”.

■ Dynamic Volume

`Off:

Audyssey Dynamic Volume off.

`Light:

■ Dynamic EQ

Light Compression Mode becomes active.

`Medium:

`Off:

Audyssey Dynamic EQ off.

Medium Compression Mode becomes active.

`Heavy:

`On:

Audyssey Dynamic EQ on.

Heavy Compression Mode becomes active. This set-

ting affects volume the most, causing all sounds to

be of equal loudness.

The Dynamic EQ indicator will light (➔ 9).

With Audyssey Dynamic EQ, you can enjoy great

sound even when listening at low volume levels.

Audyssey Dynamic EQ solves the problem of deterio-

rating sound quality as volume is decreased by taking

into account human perception and room acoustics. It

does so by selecting the correct frequency response and

surround volume levels moment-by-moment so that the

content sounds the way it was created at any volume

level — not just at reference level.

Note

• Even if you have selected other than “Audyssey” in “Equalizer”

setting after performing Audyssey 2EQ Room Correction and

Speaker Setup, selecting “On” in the “Dynamic EQ” will

change the “Equalizer” setting to “Audyssey” (➔ 42).

• When “Dynamic Volume” is set to effective, “Equalizer” set-

ting is set to “Audyssey” (➔ 42) and “Dynamic EQ” is set to

“On”. When “Dynamic EQ” is set to “Off”,

Note

“Dynamic Volume” becomes “Off” automatically.

• When “Dynamic Volume” is set to effective, the Dynamic Vol

indicator will light (➔ 9).

• If Direct listening mode is selected, this setting cannot be

selected.

• If Direct listening mode is selected, this setting cannot be

selected.

■ Reference Level

Audyssey Dynamic EQ Reference Level Offset

`0dB:

Audyssey 2EQ then removes the distortion caused by

room acoustics by capturing room acoustical problems

over the listening area in both the frequency and time

domain. The result is clear, well-balanced sound for every-

one. Enabling Audyssey 2EQ allows you to also use

Audyssey Dynamic EQ, which maintains the proper

octave-to-octave balance at any volume level.

Before using this function, connect and position all of

your speakers.

It should be used when listening to movies.

`5dB:

Select this setting for content that has a very wide

dynamic range, such as classical music.

`10dB:

Select this setting for jazz or other music that has a

wider dynamic range. This setting should also be

selected for TV content as that is usually mixed at

10 dB below film reference.

About Audyssey Dynamic EQ

`15dB:

Audyssey Dynamic EQ solves the problem of deterio-

rating sound quality as volume is decreased by taking

into account human perception and room acoustics.

Dynamic EQ selects the correct frequency response and

surround levels moment-by-moment at any user-

selected volume setting. The result is bass response,

tonal balance, and surround impression that remain con-

stant despite changes in volume. Dynamic EQ combines

information from incoming source levels with actual

output sound levels in the room, a prerequisite for deliv-

ering a loudness correction solution.

Select this setting for pop/rock music or other pro-

gram material that is mixed at very high listening

levels and has a compressed dynamic range.

Movies are mixed in rooms calibrated for film refer-

ence. To achieve the same reference level in a home the-

ater system each speaker level must be adjusted so that

–30 dBFS band-limited (500 Hz to 2000 Hz) pink noise

produces 75 dB sound pressure level at the listening

position. A home theater system automatically cali-

brated by Audyssey 2EQ will play at reference level

when the master volume control is set to the 0 dB posi-

tion. At that level you can hear the mix as the mixers

heard it.

Audyssey Dynamic EQ works in tandem with

Audyssey 2EQ to provide well-balanced sound for

every listener at any volume level.

Download from Www.Somanuals.com. All Manuals Search And Download.

Name Edit

About Audyssey Dynamic Volume

Audyssey Dynamic Volume solves the problem of large

variations in volume level between television programs,

commercials, and between the soft and loud passages of

movies. Dynamic Volume looks at the preferred volume

setting by the user and then monitors how the volume of

program material is being perceived by listeners in real

time to decide whether an adjustment is needed. When-

ever necessary, Dynamic Volume makes the necessary

rapid or gradual adjustments to maintain the desired

playback volume level while optimizing the dynamic

You can enter a custom name for each individual input

selector (excluding TUNER) and radio preset for easy

identification. When entered, the custom name will appear

on the display.

The custom name is edited using the character input

screen.

■ Name

Use q/w/e/r to select a character, and then

press ENTER.

Repeat this step to enter up to 10 characters.

range. Audyssey Dynamic EQ is integrated into

Dynamic Volume so that as the playback volume is

adjusted automatically, the perceived bass response,

tonal balance, surround impression, and dialog clarity

remain the same whether watching movies, flipping

between television channels, or changing from stereo to

surround sound content.

When you’ve finished, to store a name, be sure

to use q/w/e/r to select “OK”, and then press

ENTER. Otherwise it will not be saved.

Name input area

IntelliVolume

4 - 4. Name Edit

Name

BD/DVD

■ IntelliVolume

`–12dB to 0dB to +12dB in 1 dB steps.

With IntelliVolume, you can set the input level for each

input selector individually. This is useful if one of your

source components is louder or quieter than the others.

–

{

}

Shift

Space

Back Space

CLR

+10

Shift

All Erase

Use e/r to set the level.

If a component is noticeably louder than the others, use e

to reduce its input level. If it’s noticeably quieter, use r to

increase its input level.

]

;

’

(

)

[

Shift

Space

Back Space

CLR

A/V Sync

+10

Shift

All Erase

■ A/V Sync

`0ms to 200ms in 10 ms steps.

Shift :

Switches the displayed character.

Space:

When using your DVD player’s progressive scanning

function, you may find that the picture and sound are out

of sync. With the A/V Sync setting, you can correct this

by applying a delay to the audio signal.

To view the TV picture while setting the delay, press

ENTER.

Enters a space character.

(Left)/ (Right):

Selected when the cursor is moved within the Name

input area.

Back Space :

To return to the previous screen, press RETURN.

“Back Space” moves the cursor backward one char-

acter space. In addition, “Back Space” deletes the

character to the left of the cursor.

OK:

If HDMI Lip Sync is enabled (➔ 49) and your TV or dis-

play supports HDMI Lip Sync, the displayed delay time

will be the summation of the A/V Sync delay time and the

HDMI Lip Sync delay time. The HDMI Lip Sync delay

time is displayed underneath in parentheses.

Selects when the entry is complete.

Tip

Note

You can also be performed on the remote controller by

using +10.

• A/V Sync is disabled when the Direct listening mode is used

with an analog input source.

Press CLR on the remote controller, you can delete all

characters in the input.

Download from Www.Somanuals.com. All Manuals Search And Download.

To correct a character:

`Wide Zoom:

Use q/w/e/r to select “ ”(Left) or

“

”(Right), and then press ENTER.

Press ENTER several times to select the incor-

rect character (The cursor moves one letter

each time ENTER is pressed).

`Auto:

According to the input signals and monitor output

setting, the AV receiver automatically selects the

“4 : 3”, “Full”, “Zoom” or “Wide Zoom”. For the

monitor output setting (➔ 39).

Use q/w/e/r to select the correct character,

and then press ENTER.

Note

*1*2

■ Picture Mode

• To name a radio preset, use TUNER to select AM or FM, and

then select the preset (➔ 31).

`Thru:

The following settings are set to the default values:

“Film Mode”, “Edge Enhancement”, “Noise

Reduction”, “Brightness”, “Contrast”, “Hue” and

“Saturation”

To restore a custom name to the default, erase the custom

name by entering an empty white space for each letter.

Picture Adjust

`Custom:

Using “Picture Adjust”, you can adjust the picture qual-

ity and reduce any noise appearing on the screen.

To view the TV picture while setting, press ENTER. To

return to the previous screen, press RETURN.

You can set the following settings as you like: “Film

Mode”, “Edge Enhancement”, “Noise Reduction”,

“Brightness”, “Contrast”, “Hue” and “Saturation”

`Cinema:

Selected when the picture source is movie film, etc.

`Game:

■ Game Mode

`Off:

Game Mode off.

`On:

Select to use in connecting a game console.

With “Picture Mode”, you can change the following set-

tings to be suitable for the movie or game screen by one

operation; “Film Mode”, “Edge Enhancement”, “Noise

Reduction”, “Brightness”, “Contrast”, “Hue” or “Satu-

ration”.

Game Mode on.

If video signal delay occurs during playback on a video

component (i.e. game console), select the corresponding

input source and set the “Game Mode” setting to “On”.

The delay will decrease but in return the picture quality

will become poor.

■ Film Mode

`Video:

Does not process in either “3 : 2” or “2 : 2”.

`Auto:

*1*2

■ Wide Mode

This setting determines the aspect ratio.

Adjusts to the picture source, automatically selecting

“Film Mode”.

Note

• When the “Game Mode” is set to “On”, this setting is fixed at

“Full”.

`3 : 2:

Selected when the picture source is movie film, etc.

`2 : 2:

`4:3:

Selected when the picture source is computer graph-

ics, animation, etc.

The AV receiver will adjust to the picture source, process-

ing in either “3 : 2” or “2 : 2” (Film Mode). It automati-

cally converts the source to the appropriate progressive

signal and reproduces the natural quality of the original

picture.

When the “Film Mode” setting is set to “Auto”, the AV

receiver automatically detects the picture source and in

either “3 : 2” or “2 : 2”. However, there may be times

when you will get a better picture by setting “Film Mode”

yourself.

`Full:

`Zoom:

Note

• If the “Game Mode” setting is set to “On” (➔ 46), this setting

is fixed at “Video”.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Edge Enhancement

`0 to +10

Main menu

Listening Mode Preset

Use q/w to select the input source that you want to

With this setting you can adjust the sharpness of edges in

the picture. “0” is the softest. “+10” is the sharpest.

set, and then press ENTER.

The following menu appears.

■ Noise Reduction

5. Listening Mode Preset

`Off:

Noise reduction off.

`Low:

Low noise reduction.

`Mid:

1. BD/DVD

2. VCR/DVR

3. CBL/SAT

4. GAME

5. AUX

6. TUNER

7. TV/CD

8. PORT

For TUNER input selector only “Analog” will be

Medium noise reduction.

available.

`High:

High noise reduction.

Note

With this setting, you can reduce noise appearing on the

screen.

• If you connect an input component (such as UP-A1 series

Dock that seated iPod) to the UNIVERSAL PORT jack,

you can assign only listening modes for the analog sound

to “PORT” selector.

Note

• If the “Game Mode” setting is set to “On” (➔ 46), this setting

Use q/w to select the signal format that you want

to set, and then use e/r to select a listening mode.

Only listening modes that can be used with each

input signal format can be selected (➔ 34 to 37).

The “Last Valid” option means that the listening

mode selected last will be used.

is fixed at “Off”.

*1*2

■ Brightness

`–50 to 0 to +50

With this setting you can adjust the picture bright-

ness. “–50” is the darkest. “+50” is the brightest.

*1*2

■ Contrast

■ Analog / PCM

`–50 to 0 to +50

With this setting, you can specify the listening mode to

be used when an analog (CD, TV, LD, VHS, MD, turn-

table, radio, cassette, cable, satellite, etc.) or PCM digi-

tal (CD, DVD, etc.) audio signal is played.

With this setting you can adjust contrast. “–50” is the

least. “+50” is the greatest.

*1*2

■ Hue

`–20 to 0 to +20

■ Mono/Multiplex Source

With this setting you can adjust the red/green bal-

ance. “–20” is the strongest green. “+20” is the

strongest red.

With this setting, you can specify the listening mode to

be used when a mono digital audio signal is played

(DVD, etc.).

*1*2

■ Saturation

■ 2ch Source

`–50 to 0 to +50

With this setting, you can specify the default listening

mode for 2-channel (2/0) stereo sources in a digital for-

mat, such as Dolby Digital or DTS.

With this setting you can adjust saturation. “–50” is

the weakest color. “+50” is the strongest color.

Tip

■ Dolby D/Dolby D +/TrueHD

This procedure can also be performed on the remote controller

by using the Video menu (➔ 26).

Press CLR if you want to reset to the default value.

With this setting, you can specify the listening mode to

be used when a Dolby Digital or Dolby Digital Plus for-

mat digital audio signal is played (DVD, etc.). Specifies

the default listening mode for Dolby TrueHD sources,

such as Blu-ray or HD DVD (input via HDMI).

Listening Mode Preset

You can assign a default listening mode to each input

source that will be selected automatically when you select

each input source. For example, you can set the default lis-

tening mode to be used with Dolby Digital input signals.

You can select other listening modes during playback, but

the mode specified here will be resumed once the AV

receiver has been set to Standby.

■ DTS/DTS-ES/DTS-HD

With this setting, you can specify the listening mode to

be used when a DTS or DTS-HD High Resolution

Audio format digital audio signal is played (DVD, LD,

CD, etc.). Specifies the default listening mode for DTS-

HD Master Audio sources, such as Blu-ray or HD DVD

(input via HDMI).

■ Other Multich Source

With this setting, you can specify the default listening

mode for multichannel PCM sources from HDMI IN

such as DVD-Audio, and DSD multichannel sources

such as Super Audio CD.

Download from Www.Somanuals.com. All Manuals Search And Download.

Miscellaneous

Hardware Setup

Main menu

Miscellaneous

Main menu

Hardware Setup

Volume Setup

Remote ID

■ Maximum Volume

■ Remote ID

`Off, 30 to 79

`1, 2, or 3

With this setting, you can limit the maximum vol-

ume.

To disable this setting, select “Off”.

When several Onkyo components are used in the same

room, their remote ID codes may overlap. To differenti-

ate the AV receiver from the other components, you can

change its remote ID from “1”, to “2” or “3”.

■ Power On Volume

Note

`Last, Min, 1 to 79 or Max

With this preference, you can specify the volume set-

ting to be used each time the AV receiver is turned

on.

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you

won’t be able to control it with the remote controller.

To use the same volume level that was used when the

AV receiver was turned off, select “Last”.

The “Power On Volume” cannot be set higher than

the “Maximum Volume” setting.

Changing the Remote Controller’s ID

While holding down RECEIVER, press and hold

down SETUP until the remote indicator lights

(about 3 seconds) (➔ 38).

■ Headphone Level

Use the number buttons to enter ID 1, 2, or 3.

The remote indicator flashes twice.

`–12dB to 0dB to +12dB

With this preference, you can specify the headphone

volume relative to the main volume. This is useful if

there’s a volume difference between your speakers

and your headphones.

Tuner

For FM/AM tuning to work properly, you must specify the

FM/AM frequency step used in your area. Note that when

this setting is changed, all radio presets will be deleted.

OSD Setup

■ On Screen Display

This preference determines whether operation details

are displayed on-screen when an AV receiver function is

adjusted.

■ FM/AM Frequency Step

`200k/10kHz:

Select if 200 k/10 kHz steps are used in your area.

`50k/9kHz:

`On:

Select if 50 k/9 kHz steps are used in your area.

Displayed.

`Off:

Not displayed.

Even when “On” is selected, operation details may not be

output if the input source is connected to an HDMI IN.

■ Language

`English, Deutsch, Français, Español, Italiano,

Nederlands, Svenska, 中文

This setting determines the language used for the on-

screen setup menus.

Download from Www.Somanuals.com. All Manuals Search And Download.

HDMI

Note

• When set to “On” and close the menu, the name of connected

p-compatible components and “RIHD On” are dis-

played on the AV receiver.

When the AV receiver cannot receive the name of the compo-

nent, it is displayed as “Player*” or “Recorder*”, etc (“*”

means the number of two or more component).

When set to “Off” and close the menu, “RIHD Off” are dis-

played on the AV receiver.

■ Audio TV Out

`Off:

The audio is not output from the HDMI output.

`On:

The audio is output from the HDMI output.

This preference determines whether the incoming audio

signal is output from the HDMI OUT. You may want to

turn this preference on if your TV is connected to the

HDMI OUT and you want to listen to the audio from a

connected component through your TV’s speakers. Nor-

mally, this should be set to “Off”.

“Search…” → “(name)” → “RIHD On”

“Disconnect” → “RIHD Off”

• When an p-compatible component is connected to the

AV receiver via the HDMI cable, the name of the connected

component is displayed on the AV receiver display. For example,

while you are watching TV broadcasting, if you operate a

Blu-ray Disc/DVD player (being powered on) by the remote

control of the AV receiver, the name of the Blu-ray Disc/DVD

player is displayed on the AV receiver.

• Set to “Off” when a connected piece of equipment is not com-

patible or it is unclear whether the equipment is compatible or

not.

Note

• Listening mode cannot be changed when this setting is set to

“On” and the input source is not HDMI.

• If “On” is selected and the audio can be output from the TV, the

AV receiver will output no sound through its speakers. In this

case, “TV Sp On” appears on the display.

• When “TV Control” is set to “On ” (➔ 50), this setting is fixed

to “Auto”.

• With some TVs and input signals, no sound may be output even

• If movement is unnatural when set to “On”, change the setting

to “Off”.

• Refer to the connected component’s instruction manual for

details.

when this setting is set to “On”.

• When the “Audio TV Out” setting is set to “On”, or “TV Con-

trol” is set to “On” (➔ 50) and you’re listening through your

TV’s speakers (➔ 19), if you turn up the AV receiver’s volume

control, the sound will be output by the AV receiver’s front left

and right speakers. To stop the AV receiver’s speakers producing

sound, change the settings, change your TV’s settings, or turn

down the AV receiver’s volume.

• When the source equipment is connected with the u connec-

tion, it may malfunction if “HDMI Control (RIHD)” is set to

“On”.

■ Audio Return Channel

`Off:

Select “Off” if you don’t want to use audio return

channel (ARC) function.

`Auto:

■ Lip Sync

`Disable:

The audio signal from your TV tuner can be sent to

the HDMI OUT of the AV receiver.

Audio return channel (ARC) function enables an HDMI

(Audio Return Channel) capable TV to send the audio

stream to the HDMI OUT of the AV receiver. To use this

function, you must select the TV/CD input selector and

your TV must support ARC function.

HDMI lip sync disabled.

`Enable:

HDMI lip sync enabled.

The AV receiver can be set to automatically correct any

delay between the video and the audio, based on the data

from the connected monitor.

Note

• This function works only if your HDMI-compatible TV supports

HDMI Lip Sync.

• You can check the amount of delay being applied by the HDMI

Lip Sync function on the A/V Sync screen.

• The “Audio Return Channel” setting can be set only when the

“HDMI Control (RIHD)” setting is set to “On”.

• This setting is set to “Auto” automatically when the “HDMI

Control (RIHD)” is set to “On” first time.

■ HDMI Control (RIHD)

`Off:

■ Power Control

`Off:

Power Control disabled.

`On:

p disabled .

`On:

p enabled.

Power Control enabled.

This function allows p-compatible components

connected via HDMI to be controlled with the AV receiver

(➔ 72 to 73).

To link the power functions of p-compatible com-

ponents connected via HDMI, select “On”.

This setting is set to “On” automatically when the

“HDMI Control (RIHD)” is set to “On” first time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note

Lock Setup

• The “Power Control” setting can be set only when the “HDMI

With this preference, you can protect your settings by

locking the setup menus.

Control (RIHD)” setting is set to “On”.

• HDMI power control only works with p-compatible

components that support it and may not work properly with

some components due to their settings or compatibility.

• When set to “On”, power consumption will increase.

• When set to “On”, regardless of whether the AV receiver is On

or in Standby, both audio and video stream from an HDMI input

will be output to the TV or other components via HDMI connec-

tion (HDMI pass through function). When the HDMI pass

through function activates in standby mode, HDMI THRU indi-

cator will light.

• The power consumption during standby mode will increase dur-

ing the HDMI pass through function; however if your TV sup-

ports CEC (Consumer Electronics Control), the power

consumption can be saved in the following cases:

1. The TV is in standby mode.

Main menu

Lock Setup

■ Setup

`Locked:

Setup menus locked.

`Unlocked:

Setup menus not locked.

When the setup menus are locked, you cannot change any

setting.

Using the Audio Settings

You can change various audio settings by pressing AUDIO

(➔ 26).

2. You are watching a TV program.

• Refer to the connected component’s instruction manual for

details.

Press RECEIVER followed by AUDIO.

■ TV Control

`Off:

TV Control disabled.

`On:

Useq/w to select “Audio”, and then use q/w/e/r

to make the desired selection.

TV Control enabled.

Note

Set to “On” when you want to control the AV receiver

from an p-compatible TV that is connected to

HDMI.

• These settings are disabled when:

– a pair of headphones is connected, or

– the “Audio TV Out” setting is set to “On” ( ➔ 49) and an

input selector other than HDMI is selected.

Note

• Do not assign the component connected with the HDMI input to

the TV/CD selector when you set “TV Control” setting to “On”.

Otherwise, appropriate CEC (Consumer Electronics Control)

operation is not guaranteed.

• Set to “Off” when the TV is not compatible or when it is unclear

whether the TV is compatible or not.

• The “TV Control” setting can be set only when the “HDMI

Control (RIHD)” (➔ 49) and “Power Control” (➔ 49) set-

tings are both set to “On”.

Tone Control Settings

You can adjust the bass and treble for the front speakers,

except when the Direct listening mode is selected.

■ Bass

`–10dB to 0dB to +10dB in 2 dB steps.

You can boost or cut low-frequency sounds.

• Refer to the connected component’s instruction manual for

details.

■ Treble

`–10dB to 0dB to +10dB in 2 dB steps.

You can boost or cut high-frequency sounds.

After changing the settings of the “HDMI Control

(RIHD)”, “Audio Return Channel”, “Power Control”,

or “TV Control”, turn off the power to all connected

pieces of equipment and then turn them on again. Refer

to the user’s manuals for all connected pieces of equip-

ment.

Operating on the AV receiver

Press TONE on the AV receiver repeatedly to

select either “Bass” or “Treble”.

Use TONE LEVEL +/– on the AV receiver to

adjust.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker Levels

Music Optimizer

You can adjust the volume of each speaker while listening

to an input source.

These temporary adjustments are cancelled when the AV

receiver is set to Standby. To save the setting you made

here, go to “Level Calibration” (➔ 42) before setting the

AV receiver to Standby.

The Music Optimizer function enhances the sound quality

of compressed music files. Use it with music files that use

“lossy” compression, such as MP3.

■ Music Optimizer

`Off:

Music Optimizer off.

■ Subwoofer Level

`On:

`–15dB to 0dB to +12dB in 1 dB steps.

Music Optimizer on. The M.Opt indicator will light

(➔ 9).

■ Center Level

`–12dB to 0dB to +12dB in 1 dB steps.

Note

• The Music Optimizer function only works with PCM digital

audio input signals with a sampling rate below 48 kHz and ana-

log audio input signals. The Music Optimizer is disabled when

the Direct listening mode is selected.

Note

• You cannot use this function while the AV receiver is muted.

• Speakers that are set to “No” or “None” in the

“Speaker Configuration” (➔ 41) cannot be adjusted.

• The setting is stored individually for each input selector.

Audyssey Settings

Cinema Filter

With the Cinema Filter, you can soften overly bright

movie soundtracks, which are typically mixed for repro-

duction in a movie theater.

Cinema Filter can be used with the following listening

modes: Dolby Digital, Dolby Digital EX, Dolby Digital

Plus, Dolby TrueHD, Dolby Pro Logic IIx Movie, Dolby

Pro Logic II Movie, Dolby Pro Logic IIz Height, Multi-

channel, DTS, DTS-ES, DTS Neo:6 Cinema, DTS 96/24,

Neo:6, DTS-HD High Resolution Audio, DTS-HD Master

Audio and DTS Express.

■ Dynamic EQ

See “Dynamic EQ” in “Source Setup” (➔ 44).

■ Dynamic Volume

See “Dynamic Volume” in “Source Setup” (➔ 44).

Late Night

With the Late Night function, you can reduce the dynamic

range of Dolby Digital material so that you can still hear

quiet parts even when listening at low volume levels—

ideal for watching movies late at night when you don’t

want to disturb anyone.

■ Cinema Filter

`Off:

Cinema Filter off.

`On:

■ Late Night

For Dolby Digital and Dolby Digital Plus sources, the

options are:

Cinema Filter on.

Note

`Off:

Late Night function off.

`Low:

• The Cinema Filter may not work when used with certain input

sources.

Small reduction in dynamic range.

`High:

Large reduction in dynamic range.

For Dolby TrueHD sources, the options are:

`Auto:

The Late Night function is set to “On” or “Off”

automatically.

`Off:

Late Night function off.

`On:

Late Night function on.

Note

• The effect of the Late Night function depends on the material

that you are playing and the intention of the original sound

designer, and with some material there will be little or no effect

when you select the different options.

• The Late Night function can be used only when the input source

is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.

• The Late Night function is set to “Off” when the AV receiver is

set to Standby. For Dolby TrueHD sources, it will be set to

“Auto”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Audio Selector

Setting the Incoming Digital Signal (Fixed

Mode)

You can set priorities of audio output when there are both

digital and analog inputs.

By pressing ENTER while selecting “HDMI”, “COAX”,

“OPT” in the “Audio Selector”, you can specify the input

signal in the Fixed Mode. Pressing ENTER again allows

you to return to the “Audio Selector” setting.

Normally, the AV receiver detects the signal format auto-

matically. However, if you experience either of the follow-

ing issues when playing PCM or DTS material, you can

manually set the signal format to PCM or DTS.

If the beginnings of tracks from a PCM source are cut off,

try setting the format to PCM.

■ Audio Selector

`ARC:

The audio signal from your TV tuner can be sent to

the HDMI OUT of the AV receiver.

With this selection the TV’s audio can be automati-

cally selected as a priority among other assignments.

`HDMI:

This can be selected when HDMI IN has been

assigned as an input source. If both HDMI (HDMI

IN) and digital audio inputs (COAXIAL IN or OPTI-

CAL IN) have been assigned, HDMI input is auto-

matically selected as a priority.

If noise is produced when fast forwarding or reversing a

DTS CD, try setting the format to DTS.

`Auto:

The format is detected automatically. If no digital

input signal is present, the corresponding analog

input is used instead.

`COAX:

This can be selected when COAXIAL IN has been

assigned as an input source. If both coaxial and

HDMI inputs have been assigned, coaxial input is

automatically selected as a priority.

`PCM:

Only 2-channel PCM format input signals will be

heard. If the input signal is not PCM, the PCM indi-

cator will flash and noise may also be produced.

`DTS:

`OPT:

This can be selected when OPTICAL IN has been

assigned as an input source. If both optical and

HDMI inputs have been assigned, optical input is

automatically selected as a priority.

Only DTS (but not DTS-HD) format input signals

will be heard. If the input signal is not DTS, the DTS

indicator will flash and there will be no sound.

`Analog:

Note

The AV receiver always outputs analog signals.

• The setting is stored individually for each input selector.

• The setting will be reset to “Auto” when you change the setting

in the “Audio Selector” (➔ 52).

Note

• The setting is stored individually for each input selector.

• This setting can be made only for the input source that is

assigned as HDMI IN, COAXIAL IN, or OPTICAL IN.

You can select “ARC” if you select the TV/CD input selector.

But you cannot select it if you’ve selected “Off” in the “Audio

Return Channel” setting (➔ 49).

Download from Www.Somanuals.com. All Manuals Search And Download.

Zone 2

In addition to your main listening room, you can also enjoy playback in the other room, or as we call Zone 2. And, you

can select a different source for each room.

Connecting Your Zone 2 Speakers to an

Amp in Zone 2

Connecting Zone 2

There are two ways you can connect Zone 2 speakers:

This setup allows 7.1-channel playback in your main lis-

1. Connect them directly to the AV receiver.

tening room and 2-channel stereo playback in Zone 2,

2. Connect them to an amp in Zone 2.

with a different source in each room.

Connecting Your Zone 2 Speakers Directly

to the AV receiver

Hookup

• Use an RCA audio cable to connect the AV receiver’s

This setup allows 5.1-channel playback in your main room

and 2-channel stereo playback in Zone 2, with a different

source in each room. This is called Powered Zone 2, as the

Zone 2 speakers are powered by the AV receiver. Note that

when Powered Zone 2 is turned off, you can enjoy 7.1-

channel playback in your main room.

ZONE 2 LINE OUT L/R jacks to an analog audio input on

your Zone 2 amp.

• Connect your Zone 2 speakers to the speaker terminals on

your Zone 2 amp.

Main room

To use this setup, you must set the “Front High/

Zone2” setting to “Zone2” (➔ 54).

Hookup

AV receiver

• Connect your Zone 2 speakers to the AV receiver’s FRONT

HIGH OR ZONE 2 SPEAKERS L/R terminals.

Main room

Zone 2

AV receiver

Receiver/

integrated amp

Note

• The Zone 2 volume must be set on the Zone 2 amp.

Zone 2

Note

• With this setup, the Zone 2 volume is controlled by the AV

receiver.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the Powered Zone 2

Using Zone 2

If you’ve connected your Zone 2 speakers to the AV

receiver, as explained in “Connecting Your Zone 2 Speak-

ers Directly to the AV receiver” (➔ 53), you must set the

“Front High/Zone2” setting to “Zone2”.

This section explains how to turn Zone 2 on and off, how

to select an input source for Zone 2, and how to adjust the

volume for Zone 2.

Controlling Zone 2 from the AV receiver

Main menu

Speaker Setup

In the “Speaker Setup” menu, select “Speaker

Settings”, and then press ENTER.

OFF – /+

ZONE 2

Use q/w to select “Front High/Zone2” and e/r to

select “Zone2”.

`Zone2:

Zone 2 speakers can be used (Powered Zone 2

enabled).

Note

• When “Zone2” is selected and Zone 2 turned on, the Zone 2

speakers connected to the FRONT HIGH OR ZONE 2

SPEAKERS terminals output sound, but the surround back or

front high speakers connected to the SURR BACK OR

FRONT HIGH SPEAKERS terminals do not. When “Zone2”

is selected and Zone 2 turned off, the surround back or front high

speakers output sound as normal.

• When the “Front High/Zone2” setting is set to “Zone2” and the

input selector of Zone 2 is selected, power consumption on

standby mode slightly increases.

ZONE 2 indicator

Input selector buttons

To turn on Zone 2 and select an input source, press

ZONE 2 followed by an input selector button

within 8 seconds.

Zone 2 turns on, the ZONE 2 indicator lights.

To select AM or FM, press the TUNER input selec-

tor button repeatedly.

To select the same source as that of the main room,

press ZONE 2 repeatedly until “Z2 Selector:

Source” appears on the display.

Note

• You cannot select different AM or FM radio stations for

your main room and Zone 2. The same FM/AM radio sta-

tion will be heard in each room.

To turn off Zone 2, press OFF.

Note

• While Powered Zone 2 is being used, listening modes that

require surround back and front high speakers (6.1/7.1), such as

Dolby Digital EX, DTS-ES, and Dolby Pro Logic IIz Height are

unavailable.

• When the “Front High/Zone2” setting is set to “Zone2” and the

input selector of Zone 2 is selected, power consumption on

standby mode slightly increases.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Zone 2 with the Remote

Controller

Adjusting the Volume for Zone 2

■ Operating with the remote controller

ON/STANDBY

ZONE2

Press ZONE2.

Input selector buttons

Use VOL q/w to adjust the volume.

MUTING

■ Operating on the AV receiver

VOLq/w

Press ZONE 2 (the ZONE 2 indicator and Zone 2

selector on the display flashes).

Use –/+ within 8 seconds to adjust the volume.

Press ZONE2 and then press ON/STANDBY.

Zone 2 turns on, the ZONE 2 indicator lights.

If your Zone 2 speakers are connected to a receiver or inte-

grated amp in Zone 2, use its volume control to adjust the

volume.

To select an input source for Zone 2, press

ZONE2, followed by an input selector buttons.

To select AM or FM, press the TUNER input selec-

tor repeatedly.

Muting Zone 2

Note

■ Operating with the remote controller

• You cannot select different AM or FM radio stations for

your main room and Zone 2. The same FM/AM radio sta-

tion will be heard in each room.

Press ZONE2 followed by MUTING.

To turn off Zone 2, press ZONE2 followed by ON/

STANDBY.

Tip

• To unmute, press ZONE2 followed by MUTING again.

Note

• Only analog input sources are output by the ZONE 2 LINE

OUT and FRONT HIGH OR ZONE 2 SPEAKERS L/R ter-

minals. Digital input sources are not output. If no sound is heard

when an input source is selected, check if it’s connected to an

analog input.

• To control Zone 2, you must press the remote controller’s

ZONE2 first.

• While Powered Zone 2 is being used, listening modes that

require surround back and front high speakers (6.1/7.1), such as

Dolby Digital EX, DTS-ES and Dolby Pro Logic IIz Height are

unavailable.

• While Zone 2 is on, u functions will not work.

• You cannot select different AM or FM radio stations for your

main room and Zone 2. The same FM/AM radio station will be

heard in each room. For example, if you have an FM station for

the main room, that station will also be used in Zone 2.

• Zone 2 can also be unmuted by adjusting the volume.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling iPod & Other Components

Controlling iPod

Connecting an Onkyo Dock

No. Onkyo Dock

Cable

Note

Page

UP-A1 Dock (Included)

(Universal Port Option Dock)

—

• When UP-A1 Dock that seated iPod is 57

connected, the power consumption on

standby mode slightly increases.

• You can control your iPod when PORT

is selected as the input source.

RI Dock (Not Included)

Analog audio (RCA)

• See the RI Dock’s instruction manual 58

for more information.

To use u (Remote Interactive), you

must make an analog audio connec-

tion (RCA) between the AV receiver

and the RI Dock.

Component video

P^B/CB

PR/CR

Composite video

u cable

Models sold are different depending on the region.

Download from Www.Somanuals.com. All Manuals Search And Download.

• It is recommended that you update your iPod software before

using it with this unit. The updater for the iPod software is avail-

able at the Apple website.

Using the Onkyo Dock

For the latest information on the Onkyo Dock compo-

nents, see the Onkyo web site at:

■ Basic Operation

http://www.onkyo.com

The AV receiver may take several seconds to startup, so

you might not hear the first few seconds of the first

song.

Before using the Onkyo Dock components, update

your iPod with the latest software, available from the

Apple web site.

Auto Power On

UP-A1 Dock

If you start iPod playback while the AV receiver is on

Standby, the AV receiver will automatically turn on and

select your iPod as the input source.

With the supplied UP-A1 Dock, you can easily play the

music, photo, or movie stored on your Apple iPod through

the AV receiver and enjoy great sound.

Direct Change

You can use the AV receiver’s remote controller to operate

your iPod.

If you start iPod playback while listening to another input

source, the AV receiver will automatically select your iPod

as the input source.

Using the AV receiver’s Remote Controller

You can use the AV receiver’s remote controller to control

basic iPod functions (➔ 58).

■ Compatible iPod models

Made for:

• iPod touch (1st and 2nd generation)

• iPod classic

• iPod (4th and 5th generation)

• iPod nano (1st, 2nd, 3rd, 4th and 5th generation)

• iPod mini

■ Operating Notes

• Functionality depends on your iPod model and generation.

• Before selecting a different input source, stop iPod playback

to prevent the AV receiver from selecting the iPod input

source by mistake.

• All iPhone models

■ Putting Your iPod in the Dock

1. Turn on the AV receiver, and select the

PORT selector.

2. Align your iPod with the Dock connec-

tor, and carefully place your iPod in the

slot, as shown.

• If any accessories are connected to your iPod, the AV receiver

may not be able to select the input source properly.

• When connecting UP-A1 Dock to the radio tuner UP-HT1

with AUTO selected by the tuner’s Mode Selector switch, you

can switch the input source between UP-A1 Dock and the

tuner, by pressing PORT repeatedly on the front panel.

• While your iPod is in the UP-A1 Dock, its volume control has

no effect. If you adjust your iPod models volume control while

it’s in the UP-A1 Dock, make sure it’s not set too high before

you reconnect your headphones.

Note

• Remove the case, if fitted, from your iPod before inserting it into

the UP-A1.

• The Auto Power On function will not work if you set your

iPod in the UP-A1 Dock while it is playing.

• When Zone 2 is turned on, you can’t use Auto Power On and

Direct Change functions.

■ Adjusting the Adapter

The adapter needs to be adjusted to match your particular

iPod. If there’s a gap between the back of your iPod and

the adapter, turn the adapter counterclockwise to close the

gap. Turning the adapter counterclockwise moves it for-

ward. Turning it clockwise moves it backward.

■ Using Your iPod models Alarm Clock

You can use your iPod models Alarm Clock function to

automatically turn on your iPod and the AV receiver at a

specified time. The AV receiver’s input source will auto-

matically be set to the PORT selector.

Forward

Note

Backward

• To use this function, your iPod must be in the UP-A1 Dock, and

the UP-A1 Dock must be connected to the AV receiver.

• This function only works when the Standard mode is set to On.

• When you use this function, be sure to set the AV receiver’s vol-

ume control to a suitable level.

Note

• Make sure that the output level of the AV receiver is set to mini-

mum.

• To prevent damage to the dock connector, don’t twist your iPod

when inserting or removing it, and be careful not to knock over

the dock while your iPod is inserted.

• When Zone 2 is turned on, you can’t use this function.

• You cannot use this function for sound effects on your iPod.

• Do not take off your iPod from the Dock when you play back the

music, photo, or movie stored on your iPod.

• Don’t use the UP-A1 with any other iPod accessories, such as

FM transmitters and microphones, because they may cause a

malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Charging Your iPod models Battery

Direct Change

The UP-A1 Dock charges your iPod models battery while

your iPod is in the UP-A1 Dock and connected to the

UNIVERSAL PORT jack on the AV receiver. While your

iPod is seated in the UP-A1 Dock, its battery will be

charged when the AV receiver is set to “On” or “Standby”.

If you start iPod playback while listening to another input

source, the AV receiver will automatically switch to the

input to which the RI Dock is connected.

Other Remote Controllers

You can use the remote controller that came with the AV

receiver to control other iPod functions. The available

functionality depends on the AV receiver.

iPod Alarm

Note

• When UP-A1 Dock that seated iPod is connected, the power

consumption on standby mode slightly increases.

If you use the Alarm function on your iPod to start play-

back, the AV receiver will turn on at the specified time and

select your iPod as the input source automatically.

■ Status Messages

• PORT Reading

The AV receiver is checking the connection with the

dock.

• PORT Not Support

Note

• Linked operations do not work with video playback or when the

alarm is set to play a sound.

• If you use your iPod with any other accessories, iPod playback

detection may not work.

The AV receiver do not support the connected dock.

• PORT UP-A1

UP-A1 Dock is connected.

• This function only works when the Standard mode is set to On.

Note

■ Operating Notes

• Use the AV receiver’s volume control to adjust the playback

volume.

• While your iPod is inserted in the RI Dock, its volume control

has no effect.

• The AV receiver displays the message “UP-A1” for several sec-

onds after recognizing the UP-A1.

• When the status message is not displayed on the AV receiver’s

display, check the connection to your iPod.

• If you do adjust the volume control on your iPod while it’s

inserted in the RI Dock, be careful that it’s not set too loud

before you reconnect your earphones.

RI Dock

RI Dock is sold separately.

For supported iPod models, see the instruction man-

ual of the RI Dock.

Controlling Y o ur iPod

By pressing REMOTE MODE that’s been programmed

with the remote control code for your Dock, you can con-

trol your iPod in the Dock with the following buttons.

See “Remote Control Codes for Onkyo Components Con-

nected via u” for details on entering a remote control

code (➔ 61).

With the RI Dock, you can easily play the music stored on

your Apple iPod through the AV receiver and enjoy great

sound, and watch iPod slideshows and videos on your TV.

In addition, the onscreen display (OSD) allows you to

view, navigate, and select your iPod model’s contents on

your TV, and with the supplied remote controller, you can

control your iPod from the comfort of your sofa. You can

even use the AV receiver’s remote controller to operate

your iPod.

See the Dock’s instruction manual for more information.

■ UP-A1 Dock

PORT is preprogrammed with the remote control code for

controlling a Dock with Universal Port connector.

You can control your iPod when PORT is selected as the

input source.

Note

• Enter the appropriate remote control code before using the AV

receiver’s remote controller for the first time (➔ 61).

• Connect the RI Dock to the AV receiver with an u cable

(➔ 56).

Without the RI Control

You must enter a remote control code 82990 first (➔ 61).

• Set the RI Dock’s RI MODE switch to HDD or HDD/DOCK.

• Set the AV receiver’s Input Display to “DOCK” (➔ 27).

■ RI Dock

■ System Function

System On

• Set the RI Dock’s RI MODE switch to HDD or HDD/

DOCK.

When you turn on the AV receiver, the RI Dock and iPod

turn on automatically. In addition, when the RI Dock and

iPod are on, the AV receiver can be turned on by pressing

ON/STANDBY.

• ON/STANDBY may not work with a remote control

code (without u). In this case, make an u connection

and enter a remote control code 81993 (with u).

Auto Power On

With the RI Control

If you press the remote controller’s 1 while the AV

receiver is on Standby, the AV receiver will automatically

turn on, select your iPod as the input source, and your

iPod will start playback.

In this case, make an u connection and enter a remote

control code 81993 (with u).

• Set the AV receiver’s Input Display to “DOCK” (➔ 27).

Download from Www.Somanuals.com. All Manuals Search And Download.

✔: Available buttons

Press the appropriate REMOTE

MODE first.

Onkyo Dock

Buttons

✔

a ON/STANDBY 9

TOP MENU

✔

q/w/e/rENTER

PLAYLIST e/r

1, 3, 2, 5, 4,

7, 6

REPEAT

✔

RANDOM

PLAY MODE

DISPLAY^*6

MUTING

ALBUM +/–

i VOL q/w

RETURN

✔

• With some iPod models, generations and RI Docks, certain buttons may not work as expected.

• For detailed operation of the iPod, please refer to the instruction manual of RI Dock.

This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or off. Your iPod may not respond the first time you press this

button, in which case you should press it again.

This is because the remote controller transmits the On and Standby commands alternately, so if your iPod is already on, it will

remain on when the remote controller transmits an On command.

Similarly, if your iPod is already off, it will remain off when the remote controller transmits an Off command.

Press DISPLAY to change the following modes:

Standard mode

Nothing is displayed on your TV and you navigate and select your contents by using your iPod models display.

Only this mode can playback the video.

Extended mode (Music)

Playlists (artists, albums, songs, and so on) are displayed on your TV, and you can navigate and select your music while looking at

your TV.

Extended mode (Video)

Playlists (Movies, Music Videos, TV Shows, Video Podcasts, or Rentals) are displayed on your TV, and you can navigate and select

your video while looking at your TV.

In Extended mode (see ), PLAYLIST is used as the page jump button.

With the page modes, you can quickly locate your favorite songs even when your song lists, artist lists, and so on are very long.

Resume mode

With the Resume function, you can resume playback of the song that was playing when you removed your iPod from the RI Dock or

Standard mode is selected.

TOP MENU works as a Mode button when used with a DS-A2 RI Dock.

DISPLAY turns on backlight for 30 seconds.

Note

• In Extended mode (see ), the playback will be continued even if the AV receiver is turned off.

• In Extended mode (see ), you cannot operate your iPod directly.

• In Extended mode (see ), it may take some time to acquire the contents.

• In Extended mode (see ), video contents can not display on your TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Other Components

You can use the AV receiver’s remote controller

Use q/w to select category, and then press

(RC-764M) to control your other AV components, includ-

ing those made by other manufacturers. This section

explains how to enter the remote control code (with the

default underlined) for a component that you want to con-

trol: DVD, TV, CD, etc.

ENTER.

The brand name input panel appears.

8–1. Remote Mode Setup

Category

Brand

SON

Looking up for Remote Control Code

You can look up for appropriate remote control code from

on-screen setup menu.

Sonawa

Sonber

Songba

Sonic

Soniko

Not Listed

This setting can not be carried out by using the AV

receiver’s display.

If the brand name is not found:

Press RECEIVER followed by SETUP.

The main menu appears onscreen.

Use r to select “Not Listed”, and then press

ENTER.

The brand name input panel appears.

Use q/w to select “Remote Controller Setup”, and

then press ENTER.

Use q/w to select brand, and then press ENTER.

After searching, a remote control code and the input

procedure appear. Try it.

The “Remote Controller Setup” menu appears.

Press ENTER.

Remote control code

(Number of search results)

8–1. Remote Mode Setup

BD/DVD

VCR/DVR

CBL/SAT

GAME

AUX

8–1. Remote Mode Setup

Code

11339

1. While holding down Remote Mode [TV],

TV/CD

press and hold down [DISPLAY] (3 seconds).

2. Enter the 5-Digit remote control code.

3. Push some key to see if the TV responds.

4. Push Remote Mode [RECEIVER].

5. Choose “Works” or “Doesn’t work”.

Use q/w to select remote mode, and then press

Works

ENTER.

Doesn’t work (try next Code)

The category selection menu appears.

8–1. Remote Mode Setup

If you can control component, use q/w to select

“Works”, and then press ENTER.

TV/DVD

TV/VCR

The “Remote Mode Setup” menu appears.

If you cannot control component, use q/w to select

“Doesn’t work (try next code)” and press ENTER.

The next code is appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Enter the appropriate remote control code for

REMOTE MODE.

• BD/DVD

`31612:

Entering Remote Control Codes

You’ll need to enter a code for each component that you

want to control.

Onkyo DVD player with u

Look up the appropriate remote control code in

• TV/CD

`71327:

the separate Remote Control Codes list.

The codes are organized by category (e.g., DVD

player, TV, etc.).

Onkyo CD player with u

`42157:

While holding down REMOTE MODE to which

you want to enter a code, press and hold down

DISPLAY (about 3 seconds).

Onkyo cassette tape deck with u

• PORT

`81993:

The remote indicator lights.

Onkyo Dock

See the previous section for how to enter remote

control codes.

Note

• Remote control codes cannot be entered for RECEIVER

and ZONE 2.

Note

• Only TV remote control codes can be entered for TV.

• Except for RECEIVER, TV and ZONE 2, remote control

codes from any category can be entered as REMOTE

MODE. However, these buttons also work as input selec-

tor buttons (➔ 25), so choose a REMOTE MODE that

corresponds with the input to which you connect your

component. For example, if you connect your CD player

to the CD input, choose TV/CD when entering its remote

control code.

• When using a cassette tape deck connected via u, press

and hold TV/CD to switch to TAPE.

Press REMOTE MODE, point the remote control-

ler at the AV receiver, and operate the component.

If you want to control an Onkyo component by pointing

the remote controller directly at it, or you want to control

an Onkyo component that’s not connected via u, use the

Within 30 seconds, use the number buttons to

enter the 5-digit remote control code.

The remote indicator flashes twice.

If the remote control code is not entered success-

fully, the remote indicator will flash once slowly.

following remote control codes:

• BD/DVD

`30627:

Onkyo DVD player without u

• TV/CD

`71817:

Note

Onkyo CD player without u

• The remote control codes provided are correct at the time of

printing, but are subject to change.

`11807:

Onkyo TV

If you want to control an Onkyo component by pointing the

remote controller directly at it, use the following remote

Remote Control Codes for Onkyo

Components Connected via u

control codes:

`32900:

Onkyo Blu-ray Disc player

`32901:

Onkyo HD-DVD player

`70868:

Onkyo components that are connected via u are con-

trolled by pointing the remote controller at the AV

receiver, not the component. This allows you to control

components that are out of view, in a rack, for example.

Onkyo MD recorder

`71323:

Onkyo CD recorder

`82990:

Make sure the Onkyo component is connected

with an u cable and an analog audio cable

(RCA).

See “Connecting Onkyo u Components” for

Onkyo Dock

details (➔ 21).

Note

• If you connect a cassette tape deck to the TV/CD IN jack, or

connect an RI Dock to the to the TV/CD IN or VCR/DVR IN or

GAME IN jacks, for u to work properly, you must set the Input

Display accordingly (➔ 27).

Download from Www.Somanuals.com. All Manuals Search And Download.

Resetting REMOTE MODE Buttons

Controlling Other Components

You can reset a REMOTE MODE to its default remote

control code.

By pressing REMOTE MODE that’s been programmed

with the remote control code for your component, you can

control your component as below.

While holding down REMOTE MODE that you

want to reset, press and hold down AUDIO until

the remote indicator lights (about 3 seconds).

For details on entering a remote control code for other

components, see “Entering Remote Control Codes”

(➔ 61).

Within 30 seconds, press REMOTE MODE again.

The remote indicator flashes twice, indicating that

the button has been reset.

Each of REMOTE MODE is preprogrammed with a

remote control code. When a button is reset, its pre-

programmed code is restored.

Controlling a TV

TV is preprogrammed with the remote control code for

controlling a TV that supports the p (limited to

some models). The TV must be able to receive remote

control commands via p and be connected to the

AV receiver via HDMI. If controlling your TV via

p doesn’t work very well, program your TV’s

remote control code into TV and use the TV remote mode

to control your TV.

Resetting the Remote Controller

You can reset the remote controller to its default settings.

While holding down RECEIVER, press and hold

down AUDIO until the remote indicator lights

(about 3 seconds).

Controlling a Blu-ray Disc/DVD Player, HD

DVD Player or DVD Recorder

BD/DVD is preprogrammed with the remote control code

Within 30 seconds, press RECEIVER again.

The remote indicator flashes twice, indicating that

the remote controller has been reset.

for controlling a component that supports the p

(limited to some models). The component must be able to

receive remote control commands via p and be

connected to the AV receiver via HDMI.

The p supported by the AV receiver is the CEC

system control function of the HDMI standard.

Download from Www.Somanuals.com. All Manuals Search And Download.

✔: Available buttons

Press the appropriate REMOTE

MODE first.

Components

Buttons

ON/STANDBY

✔

b 9, INPUT,

TV VOL q/w

GUIDE

✔

TOP MENU

✔

d q/w/e/r

ENTER

SETUP

✔

f 1, 3, 2, 5,

4, 7, 6

*1*2

REPEAT

✔

RANDOM

PLAY MODE

Number: 1 to 9, 0 ✔

✔

Number: +10

DISPLAY

MUTING

CH +/–

✔

DISC +/–

PREV CH

✔

RETURN

AUDIO

✔

CLR

✔

The p function is not supported. The p sup-

ported by the AV receiver is the CEC system control function

of the HDMI standard.

These buttons function as colored buttons or A, B, C, D but-

tons.

3 (Pause) functions as reverse playback.

Note

• See the “Controlling Your iPod” about the operation of iPod

(➔ 58).

Note

• With some components, certain buttons may not work as

expected, and some may not work at all.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Troubleshooting

If you have any trouble using the AV receiver, look for a

solution in this section. If you can’t resolve the issue your-

self, contact your Onkyo dealer.

■ The STANDBY indicator flashes red

The protection circuit has been activated. Remove

the power cord from the wall outlet immediately.

Disconnect all speaker cables and input sources, and

leave the AV receiver with its power cord discon-

nected for 1 hour. After that, reconnect the power

cord and set the volume to maximum. If the AV

receiver stays on, set the volume to minimum, dis-

connect the power cord, and reconnect your speakers

and input sources. If the AV receiver turns off when

you set the volume to maximum, disconnect the

power cord, and contact your Onkyo dealer.

—

If you can’t resolve the issue yourself, try resetting the

AV receiver before contacting your Onkyo dealer.

To reset the AV receiver to its factory defaults, turn it

on and, while holding down VCR/DVR, press ON/

STANDBY. “Clear” will appear on the display and

the AV receiver will enter Standby mode.

Audio

■ There’s no sound, or it’s very quiet

Note that resetting the AV receiver will delete your

radio presets and custom settings.

Make sure that the digital input source is selected

properly.

Make sure that all audio connecting plugs are pushed 18

in all the way.

Remote indicator

Make sure that the inputs and outputs of all compo- 19-21

nents are connected properly.

Make sure that the polarity of the speaker cables is 16

correct, and that the bare wires are in contact with

the metal part of each speaker terminal.

Make sure that the input source is properly selected. 25

RECEIVER

AUDIO

Make sure that the speaker cables are not shorting. 16

Check the volume. The AV receiver is designed for

home theater enjoyment. It has a wide volume range,

allowing precise adjustment.

—

If the MUTING indicator is flashing on the display, 26

press the remote controller’s MUTING to unmute

the AV receiver.

To reset the remote controller to its factory defaults,

while holding down RECEIVER, press and hold down

AUDIO until the remote indicator lights (about 3 sec-

onds). Within 30 seconds, press RECEIVER

again.

While a pair of headphones is connected to the

PHONES jack, no sound is output by the speakers.

If there’s no sound from a DVD player connected to

an HDMI IN, check the DVD player’s output set-

tings, and be sure to select a supported audio format.

—

Check the digital audio output setting on the con-

nected device. On some game consoles, such as

those that support DVD, the default setting is off.

—

The on-screen setup menus appear only on a TV that

is connected to the HDMI OUT. If your TV is con-

nected to the MONITOR OUT V or the COMPO-

NENT VIDEO OUT, use the AV receiver’s display

when changing settings.

With some DVD-Video discs, you need to select an

audio output format from a menu.

—

If your turntable uses an MC cartridge, you must

connect an MC head amp, or an MC transformer.

Make sure that none of the connecting cables are

bent, twisted, or damaged.

Power

Not all listening modes use all speakers.

■ Can’t turn on the AV receiver

Specify the speaker distances and adjust the individ- 41

ual speaker levels.

Make sure that the power cord is properly plugged

into the wall outlet.

—

Make sure that the speaker setup microphone is not

still connected.

—

Unplug the power cord from the wall outlet, wait five

seconds or more, then plug it in again.

The input signal format is set to PCM or DTS. Set it 52

to Auto.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Only the front speakers produce sound

■ The speaker volume cannot be set as required

(The volume cannot be set to 79 dB)

When the Stereo or Mono listening mode is selected,

only the front speakers and subwoofer produce

sound.

—

Check to see if a maximum volume has been set.

If the volume level of each individual speaker has

been adjusted to high positive values, then the maxi-

mum master volume possible may be reduced. Note

that the individual speaker volume levels are set

automatically after the Audyssey 2EQ^®Room Cor-

rection and Speaker Setup function has been com-

pleted.

28, 41

Check the Speaker Configuration.

■ Only the center speaker produces sound

If you use the Dolby Pro Logic IIx Movie, Dolby Pro

Logic IIx Music, or Dolby Pro Logic IIx Game lis-

tening mode with a mono source, such as an AM

radio station or mono TV program, the sound is con-

centrated in the center speaker.

—

■ Noise can be heard

Using cable ties to bundle audio cables with power

cords, speaker cables, and so on may degrade the

audio performance, so don’t do it.

—

Make sure the speakers are configured correctly.

■ The surround speakers produce no sound

An audio cable may be picking up interference. Try

repositioning your cables.

When the T-D (Theater-Dimensional), Stereo or

Mono listening mode is selected, the surround

speakers produce no sound.

—

■ The Late Night function doesn’t work

Depending on the source and current listening mode,

not much sound may be produced by the surround

speakers. Try selecting another listening mode.

—

Make sure the source material is Dolby Digital,

Dolby Digital Plus, and Dolby TrueHD.

Make sure the speakers are configured correctly.

■ About DTS signals

■ The center speaker produces no sound

When DTS program material ends and the DTS bit-

stream stops, the AV receiver remains in DTS listen-

ing mode and the DTS indicator remains on. This is

to prevent noise when you use the pause, fast for-

ward, or fast reverse function on your player. If you

switch your player from DTS to PCM, because the

AV receiver does not switch formats immediately,

you may not hear any sound, in which case you

should stop your player for about three seconds, and

then resume playback.

—

When the Stereo or Mono listening mode is selected,

the center speaker produces no sound.

—

Make sure the speakers are configured correctly.

■ The front high and surround back speakers

produce no sound

Depending on the current listening mode, no sound 34

may be produced by the front high and surround

back speakers. Select another listening mode.

With some CD and LD players, you won’t be able to

playback DTS material properly even though your

player is connected to a digital input on the AV

receiver. This is usually because the DTS bitstream

has been processed (e.g., output level, sampling rate,

or frequency response changed) and the AV receiver

doesn’t recognize it as a genuine DTS signal. In such

cases, you may hear noise.

—

Not much sound may be produced by the front high

and surround back speakers with some sources.

—

Make sure the speakers are configured correctly.

While Powered Zone 2 is being used, playback in the 53

main room is reduced to 5.1-channels and the front

high, and surround back speakers produce no sound.

When playing DTS program material, using the

pause, fast forward, or fast reverse function on your

player may produce a short audible noise. This is not

a malfunction.

■ The subwoofer produces no sound

When you play source material that contains no

information in the LFE channel, the subwoofer pro-

duces no sound.

—

■ The beginning of audio received by an HDMI IN

can’t be heard

Make sure the speakers are configured correctly.

Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio sig-

nals, audio output may not start immediately.

—

■ There’s no sound with a certain signal format

Check the digital audio output setting on the con-

nected device. On some game consoles, such as

those that support DVD, the default setting is off.

—

With some DVD-Video discs, you need to select an

audio output format from a menu.

—

Depending on the input signal, some listening modes 34–37

cannot be selected.

■ Can’t get 6.1/7.1 playback

If no surround back speakers, and front high speak-

ers are connected, or the Zone 2 speakers are being

used, 6.1/7.1 playback is not possible.

—

You can not always select all of the listening modes, 34–37

depending on the number of the speakers connected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Video

Tu ner

■ There’s no picture

■ Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t light

Make sure that all video connecting plugs are pushed 18

in all the way.

Relocate your antenna.

—

Make sure that each video component is properly

connected.

19, 20,

Move the AV receiver away from your TV or com-

puter.

If your TV is connected to the HDMI OUT, select

“- - - - -” in the “HDMI Input” setup to watch com-

posite video, and component video sources.

Listen to the station in mono.

When listening to an AM station, operating the

remote controller may cause noise.

—

If the video source is connected to a component

video input, you must assign that input to an input

selector, and your TV must be connected to either

the HDMI OUT or COMPONENT VIDEO OUT.

20, 39

Passing cars and airplanes can cause interference.

Concrete walls weaken radio signals.

—

If nothing improves the reception, install an outdoor

antenna.

If the video source is connected to a composite video 20

input, your TV must be connected to the HDMI

OUT or the corresponding composite video output.

Remote Controller

If the video source is connected to an HDMI input, 19, 39

you must assign that input to an input selector, and

your TV must be connected to the HDMI OUT.

■ The remote controller doesn’t work

Before operating this unit, be sure to press

RECEIVER.

—

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

—

Make sure that the batteries are installed with the

correct polarity.

■ There’s no picture from a source connected to

an HDMI IN

Install new batteries. Don’t mix different types of

batteries, or old and new batteries.

Reliable operation with an HDMI-to-DVI adapter is 72

not guaranteed. In addition, video signals from a PC

are not guaranteed.

Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the

AV receiver’s remote control sensor.

When the Resolution is set to any resolution not sup- 39

ported by the TV, no video is output by the HDMI

outputs.

Make sure that the AV receiver is not subjected to

direct sunshine or inverter-type fluorescent lights.

Relocate if necessary.

—

If the message “Resolution Error” appears on the

AV receiver’s display, this indicates that your TV

does not support the current video resolution and

you need to select another resolution on your DVD

player.

—

If the AV receiver is installed in a rack or cabinet

with colored-glass doors, the remote controller may

not work reliably when the doors are closed.

Make sure you’ve selected the correct remote con- 12, 62

troller mode.

■ The on-screen menus don’t appear

When using the remote controller to control other

manufacturers’ AV components, some buttons may

not work as expected.

—

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

—

Make sure you’ve entered the correct remote control 61

code.

When the AV receiver doesn’t connect TV with

HDMI, onscreen menus are not displayed.

Make sure to set the same ID on both the AV receiver 48

and remote controller.

■ The on screen display does not appear

Depending on the input signal, the on screen display 48

may not appear when the input signal from the

HDMI IN is output to a device connected to the

HDMI OUT.

■ Can’t control other components

If it’s an Onkyo component, make sure that the u

cable and analog audio cable are connected properly.

Connecting only an u cable won’t work.

Make sure you’ve selected the correct remote con- 12, 62

troller mode.

If you’ve connected a cassette tape deck, to the TV/ 27

CD IN jack, or an RI Dock to the TV/CD IN or

GAME IN or VCR/DVR IN jacks, for the remote

controller to work properly, you must set the display.

If you cannot operate it, you will need to enter the

appropriate remote control code.

To control another manufacturer’s component, point 61

the remote controller at that component.

To control an Onkyo component that’s connected via 61

u, point the remote controller at the AV receiver.

Be sure to enter the appropriate remote control code

first.

Download from Www.Somanuals.com. All Manuals Search And Download.

To control an Onkyo component that’s not connected 61

via u, point the remote controller at the compo-

nent. Be sure to enter the appropriate remote control

code first.

Recording

■ Can’t record

On your recorder, make sure the correct input is

selected.

—

The entered remote control code may not be correct.

If more than one code is listed, try each one.

—

To prevent signal loops and damage to the AV

receiver, input signals are not fed through to outputs

with the same name (VCR/DVR IN to VCR/DVR

OUT).

UP-A1 Dock for iPod

■ There’s no sound

Make sure your iPod is actually playing.

—

Zone 2

Make sure your iPod is inserted properly in the

Dock.

■ There’s no sound

Make sure the UP-A1 Dock is connected to the UNI- —

VERSAL PORT jack on the AV receiver.

Only components connected to analog inputs can be

played in Zone 2.

—

Make sure the AV receiver is turned on, the correct

input source is selected, and the volume is turned up.

—

■ The Zone 2 speakers produce no sound

Make sure the plugs are pushed in all the way.

Try resetting your iPod.

—

To use the Zone 2 speakers, you must set the “Front 54

High/Zone2” setting to “Zone2” .

■ There’s no video

Others

Make sure that your iPod model’s TV OUT setting is

set to On.

—

■ The sound changes when I connect my

headphones

Make sure the correct input is selected on your TV or

the AV receiver.

When a pair of headphones is connected, the listen-

ing mode is set to Stereo, unless it’s already set to

Stereo, Mono or Direct.

—

Some versions of the iPod do not output video.

■ The AV receiver’s remote controller doesn’t

control your iPod

■ The speaker distance cannot be set as required

Make sure your iPod is properly inserted in the

Dock. If your iPod is in a case, it may not connect

properly to the Dock. Always remove your iPod

from the case before inserting it into the Dock.

—

In some cases, corrected values suitable for home

theater use may be set automatically.

—

■ How do I change the language of a multiplex

source

The iPod cannot be operated while it’s displaying the

Apple logo.

—

Use the “Multiplex” setting on the “Audio Adjust” 42

menu to select “Main” or “Sub”.

Make sure you’ve selected the right remote mode.

—

When you use the AV receiver’s remote controller,

point it toward your AV receiver.

■ The u functions don’t work

When connecting UP-A1 Dock to the radio tuner

UP-HT1 with AUTO selected by the tuner’s Mode

Selector switch, you can switch the input source

between UP-A1 Dock and the tuner, by pressing

PORT repeatedly on the front panel.

—

To use u, you must make an u connection and an

analog audio connection (RCA) between the compo-

nent and AV receiver, even if they are connected dig-

itally.

If you still can’t control your iPod, start playback by

pressing your iPod model’s Play button. Remote

operation should then be possible.

—

■ The functions System On/Auto Power On and

Direct Change don’t work for components

connected via u

Try resetting your iPod.

—

Depending on your iPod, some buttons may not

work as expected.

These functions don’t work when Zone 2 is turned 21

on.

■ The AV receiver unexpectedly selects your iPod

as the input source

■ When performing “Audyssey 2EQ Room

Correction and Speaker Setup”, the

measurement fails showing the message

“Ambient noise is too high.”.

Always pause iPod playback before selecting a dif-

ferent input source. If playback is not paused, the

Direct Change function may select your iPod as the

input source by mistake during the transition

between tracks.

—

This can be caused by any malfunction in your

speaker unit. Check if the unit produces normal

sounds.

—

Download from Www.Somanuals.com. All Manuals Search And Download.

■ The following settings can be made for the

composite video inputs

Important Note Regarding Video Playback

You must use the buttons on the unit to make these set-

tings.

1. While holding down the input selector button for the input

source that you want to set, press SETUP.

The AV receiver can upconvert component video and

composite video sources for display on a TV connected to

the HDMI OUT. However, if the picture quality of the

source is poor, upconversion may make the picture worse

or disappear altogether.

2. Use e/r to change the setting.

3. Press the input selector button for the input source that you

want to set when you’ve finished.

In this case, try the following:

• Video Attenuation

This setting can be made for the BD/DVD, VCR/DVR,

CBL/SAT, GAME, or AUX input.

If you have a games console connected to the composite

video input, and the picture isn’t very clear, you can

attenuate the gain.

If the video source is connected to a component

video input, connect your TV to the COMPO-

NENT VIDEO OUT.

If the video source is connected to a composite video

input, connect your TV to the MONITOR OUT V.

On the main menu, select “1. Input/Output

Video ATT:OFF: (default).

Video ATT:ON: Gain is reduced by 2 dB.

Assign”, and then select “2. HDMI Input”.

Select the relevant input selector, and assign it to

“- - - - -” (➔ 39).

The AV receiver contains a microcomputer for signal

processing and control functions. In very rare situations,

severe interference, noise from an external source, or

static electricity may cause it to lockup. In the unlikely

event that this happens, unplug the power cord from the

wall outlet, wait at least five seconds, and then plug it

back in again.

On the main menu, select “1. Input/Output

Assign”, and then select “3. Component Video

Input” (➔ 40):

If the video source is connected to COMPONENT

VIDEO IN 1, select the relevant input selector, and

assign it to “IN1”.

If the video source is connected to COMPONENT

VIDEO IN 2, select the relevant input selector, and

assign it to “IN2”.

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded cor-

rectly.

If the video source is connected to composite video

input, select the relevant input selector, and assign it

to “- - - - -”.

Before disconnecting the power cord from the wall out-

let, set the AV receiver to Standby.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

AV receiver

Amplifier Section

General

Rated Output Power

All channels:

Power Supply

Power Consumption

Stand-by Power Consumption

AC 120 V, 60 Hz

4.9 A

130 watts minimum continuous power

per channel, 6 ohm, at 1 kHz with a

maximum total harmonic distortion of

0.2 W

Dimensions

^(W× H × D)

Dynamic Power

Damping Factor

180 W (3 Ω, Front)

160 W (4 Ω, Front)

100 W (8 Ω, Front)

^17-1/8"× 5-15/16" × 12-15/16"

435 mm × 151.5 mm × 328.5 mm

Weight

8.6 kg (19.0 lbs.)

60 (Front, 1 kHz, 8 Ω)

Input Sensitivity and Impedance

200 mV/47 kΩ (LINE)

Rated RCA Output Level and Impedance

200 mV/2.2 kΩ (REC OUT)

Frequency Response 5 Hz - 100 kHz/+1 dB, -3 dB (DSP bypass)

Tone Control Characteristics

■ HDMI

Input

Output

Video Resolution

Audio Format

IN 1, IN 2, IN 3, IN 4

OUT

1080p

Dolby True HD, DTS Master Audio,

DVD-Audio, DSD

10 dB, 50 Hz (BASS)

10 dB, 20 kHz (TREBLE)

Supported

3D, Audio Return Channel, Deep Color,

x.v.Color, LipSync, CEC

Signal to Noise Ratio 106 dB (LINE, IHF-A)

Speaker Impedance

6 Ω - 16 Ω

■ Video Inputs

Video Section

Component

Composite

IN 1, IN 2

BD/DVD, VCR/DVR, CBL/SAT, GAME,

AUX

Input Sensitivity/Output Level and Impedance

1 Vp-p/75 Ω (Component Y)

0.7 Vp-p/75 Ω (Component P^B/CB, PR/CR)

■ Video Outputs

1 Vp-p/75 Ω (Composite)

Component Video Frequency Response

5 Hz - 100 MHz/+0 dB, -3 dB

Component

Composite

OUT

MONITOR OUT, VCR/DVR OUT

Tuner Section

■ Audio Inputs

Digital

Optical: 2

Coaxial: 2

FM Tuning Frequency Range

87.5 MHz - 107.9 MHz

AM Tuning Frequency Range

530 kHz - 1710 kHz

Analog

BD/DVD, VCR/DVR, CBL/SAT, GAME,

TV/CD, AUX

Preset Channel

■ Audio Outputs

Analog

Subwoofer Pre Output

VCR/DVR, ZONE2 Line Out

Speaker Outputs

Phones

Main (L, R, C, SL, SR, SBL, SBR)

+ ZONE2 / Front High (L, R)

1 (6.3 ø)

■ Others

SETUP MIC

Universal Port

Specifications and features are subject to change

without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

7.1ch Home Theater Speaker Package (HTP-680)

■ Powered Subwoofer (SKW-770)

■ Center Speaker (SKC-680)

Type

Input sensitivity/Impedance

140 mV/20 kΩ

Bass-reflex

Type

Impedance

Maximum input power 130 W

2 Way closed box

6Ω

Maximum output power

Sensitivity

Frequency response

Crossover frequency 4 kHz

Cabinet capacity

81 dB/W/m

60 Hz to 50 kHz

290 W (Dynamic power)

25 Hz to 150 Hz

Frequency response

Cabinet capacity

37 L (1.3 cubic feet)

2.1 L (0.074 cubic feet)

Dimensions (W × H × D)

^{Dimensions (W}× H × D)

10-13/16" × 19-15/16" × 16-3/16"

11-7/16" × 4-13/16" × 4-7/16"

275 mm × 507 mm × 411 mm

290 mm × 122 mm × 113 mm

(incl. projection)

(incl. grille and projection)

Weight

11.6 kg (25.6 lbs.)

10" (25 cm) Cone Woofer

AC 120 V, 60 Hz

163 W

Weight

Drivers unit

1.1 kg (2.4 lbs.)

Drivers unit

Power supply

Power consumption

4" (10 cm) Cone (Woofer) × 2

1" (2.5 cm) Balanced dome (Tweeter)

Terminal

Keyhole slot

Grille

Spring type color coded

■ Front Speaker (SKF-680)

Fixed

Type

Impedance

Maximum input power 130 W

2 Way closed box

6Ω

■ Surround/Surround Back Speaker

(SKR-680/SKB-680)

Sensitivity

Frequency response

81 dB/W/m

60 Hz to 50 kHz

Type

Impedance

Full-Range closed box

6Ω

Crossover frequency 4 kHz

Maximum input power 130 W

Cabinet capacity

2.1 L (0.074 cubic feet)

Sensitivity

79 dB/W/m

Frequency response

Cabinet capacity

70 Hz to 20 kHz

^{Dimensions (W}× H × D)

2.1 L (0.074 cubic feet)

4-3/4" × 11-7/16" × 4"

120 mm × 290 mm × 102 mm

Dimensions (W × H × D)

(incl. grille and projection)

4-3/4" × 11-7/16" × 4"

Weight

1.1 kg (2.4 lbs.)

^{120 mm}× 290 mm × 102 mm

Drivers unit

(incl. grille and projection)

4" (10 cm) Cone (Woofer) × 2

1" (2.5 cm) Balanced dome (Tweeter)

Weight

0.8 kg (1.8 lbs.)

8 cm (3-1/4") Cone

Spring type color coded

Terminal

Keyhole slot

Grille

Spring type color coded

Drivers unit

Terminal

Keyhole slot

Grille

Fixed

Download from Www.Somanuals.com. All Manuals Search And Download.

7.1ch Home Theater Speaker Package (HTP-780)

■ Powered Subwoofer (SKW-780)

■ Center Speaker (SKC-780)

Type

Input sensitivity/Impedance

140 mV/20 kΩ

Bass-reflex

Type

Impedance

Maximum input power 130 W

2 Way Bass-reflex

6Ω

Maximum output power

Sensitivity

Frequency response

Crossover frequency 4 kHz

Cabinet capacity

79 dB/W/m

60 Hz–50 kHz

290 W (Dynamic power)

25 Hz to 150 Hz

Frequency response

Cabinet capacity

37 L (1.3 cubic feet)

2.8 L (0.10 cubic feet)

Dimensions (W × H × D)

^{Dimensions (W}× H × D)

16-9/16" × 4-1/2" × 4-3/4"

10-13/16" × 19-15/16" × 16-3/16"

420 mm × 115 mm × 121 mm

(incl. grille and projection)

275 mm × 507 mm × 411 mm

(incl. projection)

Weight

2.2 kg (4.9 lbs.)

Weight

11.6 kg (25.6 lbs.)

10" (25 cm) Cone Woofer

AC 120 V, 60 Hz

163 W

Drivers unit

3-1/4" (8 cm) Cone (Woofer) × 2

Drivers unit

Power supply

Power consumption

1" (2.5 cm) Balanced dome (Tweeter)

Terminal

Keyhole slot

Grille

Spring type color coded

Fixed

■ Front Speaker (SKF-780)

Type

Impedance

Maximum input power 130 W

Sensitivity

Frequency response

Crossover frequency 4 kHz

Cabinet capacity

2 Way Bass-reflex

6Ω

■ Surround/Surround Back Speaker

(SKR-780/SKB-780)

Type

Full-Range closed box

79.5 dB/W/m

55 Hz–50 kHz

Impedance

6Ω

Maximum input power 130 W

Sensitivity

81 dB/W/m

7.3 L (0.26 cubic feet)

Frequency response

Cabinet capacity

80 Hz–20 kHz

Assembly dimensions (with supplied speaker base)

(W × H × D):

1.0 L (0.036 cubic feet)

^{Dimensions (W}× H × D)

10-5/16" × 41-1/8" × 10-5/16"

262 mm × 1045 mm × 262 mm

(incl. projection)

4-1/2" × 9-1/16" × 3-3/4"

115 mm × 230 mm × 96 mm

Weight

5.2 kg (11.5 lbs.)

(incl. speaker base)

(incl. grille and projection)

Weight

1.0 kg (2.2 lbs.)

3-1/4" (8 cm) Cone

Spring type color coded

Drivers unit

3-1/4" (8 cm) Cone (Woofer) × 2

1" (2.5 cm) Balanced dome (Tweeter)

Drivers unit

Terminal

Keyhole slot

Grille

Terminal

Grille

Spring type color coded

Fixed

Dock for iPod UP-A1

Dimensions (W × H × D)

^3-1/4"× 1-5/16" × 2-15/16"

83 mm × 33 mm × 74 mm

170 g (6 ounces)

Weight

Specifications and features are subject to change

without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

About HDMI

Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital

interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video compo-

nents. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a

single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichan-

nel digital audio, and multichannel PCM).

The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface) , so TVs and displays with

a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and displays,

resulting in no picture.)

The AV receiver uses HDCP (High-bandwidth Digital Content Protection) , so only HDCP-compatible components can

display the picture.

The AV receiver’s HDMI interface is based on the following:

Audio Return Channel, 3D, x.v.Color, Deep Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution

Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multichannel PCM

Supported Audio Formats

• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)

• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz, 16/20/24 bit)

• Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio, DTS-HD

Master Audio)

Your Blu-ray Disc/DVD player must also support HDMI output of the above audio formats.

About Copyright Protection

The AV receiver supports HDCP (High-bandwidth Digital Content Protection) , a copy-protection system for digital

video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.

DVI (Digital Visual Interface): The digital display interface standard set by the DDWG in 1999.

HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s

designed to protect video content and requires a HDCP-compatible device to display the encrypted video.

DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this

open industry group’s objective is to address the industry’s requirements for a digital connectivity specification for high-performance

PCs and digital displays.

Note

• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by

using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need to make a separate connection for

audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.

• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or

there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for

details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using an RIHD-compatible TV, Player, or Recorder

p, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo

components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over

HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, opera-

tion with components other than p-compatible components cannot be guaranteed.

■ About p-compatible components

■ Operations that can be performed with p

connection

The following components are p-compatible. (As

of February 2010) See the Onkyo web site for latest infor-

mation.

For p-compatible TV

The following linked operation is possible by connecting

the AV receiver to an p-compatible TV.

• The AV receiver will enter Standby mode when the

power of the TV is turned to Standby.

• You can set on the menu screen of the TV to either out-

put the audio from the speakers connected to the AV

receiver, or from the speakers of the TV.

• Panasonic VIERA Link compatible TV

• Toshiba REGZA-LINK compatible TV

• Sharp TV (See Onkyo web site for latest information on

compatible models.)

Players/Recorders

• It is possible to output the video/audio from the antenna

or from the input jack of the TV from the speakers con-

nected to the AV receiver. (A connection such as optical

digital cable or similar is required above the HDMI

cable.)

• Onkyo and Integra p-compatible players

• Panasonic VIERA Link compatible players and record-

ers (only when used together with Panasonic VIERA

Link compatible TV)

• Toshiba REGZA-LINK compatible players and record-

ers (only when used together with Toshiba REGZA-

LINK compatible TV)

• Input to the AV receiver can be selected with the remote

controller of the TV.

• Operations such as volume adjustment or similar for the

AV receiver can be performed from the remote controller

of the TV.

• Sharp players and recorders (only when used together

with Sharp TV)

For p-compatible players/recorders

Models other than those mentioned above may have some

interoperability if compatible with CEC which is part of the

HDMI Standard, but operation cannot be guaranteed.

The following link operation is possible by connecting the

AV receiver to an p-compatible player/recorder.

• When the playback is started on the player/recorder,

input of the AV receiver will switch to the HDMI input

of the player/recorder that is playing back.

Note

• Do not connect the p-compatible component more than

the following number to the HDMI input terminal so that the

linked operations work properly.

• Operation of the player/recorder is possible with the

remote controller supplied with the AV receiver.

– Blu-ray Disc/DVD player is up to three.

– Blu-ray Disc recorder/DVD recorder/Digital Video Recorder

is up to three.

Not all functions may operate depending on the model.

– Cable/Satellite Set-top box is up to four.

• Do not connect the AV receiver to the other AV receiver/AV

amplifier via HDMI.

• When the p-compatible component more than the

above-mentioned is connected, the linked operations are not

guaranteed.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ How to connect and setup

Confirm the settings.

1. Turn on the power for all connected components.

2. Turn off the power of the TV, and confirm that

the power of the connected components is turned

off automatically with the link operation.

3. Turn on the power of the Blu-ray Disc/DVD

player/recorder.

Confirm the connecting and setting.

1. Connect the HDMI OUT jack to the HDMI input

jack of the TV.

Blu-ray Disc/DVD player, etc.

4. Start playback of the Blu-ray Disc/DVD player/

recorder, and confirm the following.

HDMI

connection

• The power of the AV receiver is turned on

automatically, and input with the Blu-ray

Disc/DVD player/recorder connected is

selected.

AV receiver

• The power of the TV is turned on automati-

cally, and input with the AV receiver con-

nected is selected.

DIGITAL AUDIO

connection

(OPTICAL)

HDMI

connection

5. Following the operating instructions of the TV,

select “Use the TV speakers” from the menu

screen of the TV, and confirm that the audio is

output from the speakers of the TV, and not from

the speakers connected to the AV receiver.

6. Select “Use the speakers connected from the AV

receiver” from the menu screen of the TV, and

confirm that the audio is output from the speak-

ers connected to the AV receiver, and not from

the TV speakers.

TV, projector, etc.

2. Connect the audio output from the TV to the

OPTICAL IN 2 jack of the A V r eceiver using an

optical digital cable.

Note

• When the audio return channel (ARC) function is used

with TV for HDMI (Audio Return Channel), it should not

be this connection (➔ 49).

3. Connect the HDMI output of the Blu-ray Disc/

Note

DVD player/recorder to the HDMI IN 1 jack of

the AV receiver.

• Perform the above operations when you initially use the

AV receiver, when the settings of each component are

changed, when the main power of each component is

turned off, when the power cable is disconnected from the

power supply, or when there has been a power outage.

Note

• It is necessary to assign the HDMI input when connecting

the Blu-ray Disc/DVD player/recorder to other jacks

(➔ 39). Do not assign the components connected to the

HDMI IN to the TV/CD input at this time. Appropriate

CEC (Consumer Electronics Control) operation can not be

guaranteed.

Operate with the remote controller.

For buttons that can be operated (➔ 62).

Note

• Audio from DVD-Audio or Super Audio CD may not out-

put from the TV speakers. You will be able to output the

audio from the TV speakers by setting the audio output of

the DVD player to 2ch PCM. (It may not be possible

depending on the player models.)

• Even if you set to output audio on the TV speakers, audio

will be output from the speakers connected to the AV

receiver when you adjust the volume or switch the input

on the AV receiver. To output audio from the TV speakers,

re-do the operations on the TV.

Change each item in the “HDMI Setup” as below:

• HDMI Control (RIHD): On

• Audio Return Channel (ARC): Auto

• Power Control: On

• TV Control: On

See details of each setting (➔ 49).

• Do not connect the u cable when connecting to the u

and u audio control compatible components.

• When you select anything other than the HDMI jack

where the AV receiver is connected as the input on the TV,

input on the AV receiver will be switched to “TV/CD”.

• The AV receiver will automatically power on in conjunc-

tion when it determines it to be necessary. Even if the AV

receiver is connected to an p compatible TV or

player/recorder, it will not power on if it is not necessary.

It may not power on in conjunction when the TV is set to

output audio from the TV.

• Linked functions with the AV receiver may not work

depending on the model. Operate the AV receiver directly

in such cases.

Download from Www.Somanuals.com. All Manuals Search And Download.

Video Resolution Chart

The following tables show how video signals at different resolutions are output by the AV receiver.

✔: Output

HDMI

Component

Composite

Output

1080p 1080i 720p 480p 480i 1080p 1080i 720p 480p 480i 480i

Input

HDMI

1080p

✔

1080i

720p

480p

480i

✔

Component

Composite

1080p

1080i

720p

480p

480i

✔

480i

✔

Download from Www.Somanuals.com. All Manuals Search And Download.

Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH (UK BRANCH)

The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK

Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700

ONKYO CHINA LIMITED

Unit 1 & 12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung,

N.T., Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039

http://www.ch.onkyo.com/

Y1004-1

SN 29400232

* 2 9 4 0 0 2 3 2 *

Download from Www.Somanuals.com. All Manuals Search And Download.

Nady Systems DJ Equipment SRM 12X User Manual
NCR Wireless Office Headset 5953 User Manual
Nokia Bluetooth Headset BH 203 User Manual
NordicTrack Treadmill NTL169050 User Manual
NordicTrack Treadmill NTL778061 User Manual
Nortel Networks Switch NN46225 300 User Manual
Oregon Scientific Fitness Electronics PE326CA User Manual
Oregon Scientific Games 086 003875 034 User Manual
Panasonic Network Card 2SD1820G User Manual
Parasound Stereo Amplifier 5250 V2 User Manual