Onkyo DVD Player DV S353 User Manual

Contents  
Before UsingYour DVD Player  
2
DVD Player  
Getting Started  
6
DV-S353  
Facilities and Connections 10  
Instruction Manual  
Basic Operation  
17  
20  
Advanced Operation  
Thank you for purchasing the Onkyo DVD Player.  
Please read this manual thoroughly before making  
connections and turning on the power.  
Following the instructions in this manual will enable  
you to obtain optimum performance and listening  
enjoyment from your new Player.  
Function Setup  
Others  
28  
34  
Please retain this manual for future reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions  
This unit contains a semiconductor laser system and is classified as a  
“CLASS 1 LASER PRODUCT”. So, to use this model properly, read  
this Instruction Manual carefully. In case of any trouble, please contact  
the store where you purchased the unit. To prevent being exposed to the  
laser beam, do not try to open the enclosure.  
The label on the right is  
applied on the rear  
panel except for USA  
and Canadian models.  
“CLASS 1 LASER  
PRODUCT”  
CAUTION:  
1. This unit is a CLASS 1 LASER PRODUCT and employs a laser  
inside the cabinet.  
VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK  
FAILED OR DEFEATED. DO NOT STARE INTO BEAM.  
2. To prevent the laser from being exposed, do not remove the  
cover. Refer servicing to qualified personnel.  
CAUTION:  
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR  
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER  
THAN THOSE SPECIFIED HEREIN MAY RESULT IN  
HAZARDOUS RADIATION EXPOSURE.  
For U.S. model  
For Canadian model  
The laser is covered by a housing which prevents exposure during  
operation or maintenance. However, this product is classified as a Laser  
Product by CDRH (Center for Devices and Radiological Health) which is a  
department of the Food and Drug Administration. According to their  
regulations 21 CFR section 1002.30, all manufactures who sell Laser  
Products must maintain records of written communications between the  
manufacturer, dealers and customers concerning radiation safety. If you  
have any complaints about instructions or explanations affecting the use of  
this product, please feel free to write to the address on the back page of this  
manual. When you write us, please include the model number and serial  
number of your unit.  
This class B digital apparatus complies with Canadian ICES-003.  
For models having a power cord with a polarized plug:  
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE  
OF PLUG TO WIDE SLOT, FULLY INSERT.  
Modele pour les Canadien  
Cet appareil numérique de la classe B est conforme à la norme NMB-003  
du Canada.  
In compliance with Federal Regulations, the certification, identification  
and the period of manufacture are indicated on the rear panel.  
Sur les modeles dont la fiche est polarisee:  
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,  
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA  
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU  
FOND.  
FCC INFORMATION FOR USER  
CAUTION:  
The user changes or modifications not expressly approved by the party  
responsible for compliance could void the user’s authority to operate the  
equipment.  
NOTE:  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference  
in a residential installation. This equipment generates, uses and can radiate  
radio frequency energy and, if not installed and used in accordance with  
the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions  
1. Regional Restriction Codes (Region Number)  
9. Notes on Handling  
Regional restriction codes are built into DVD Players and DVD-Video  
media for each sales region. If the regional code of the DVD Player  
does not match one of the regional codes on the DVD-Video, playback  
is not possible.  
When shipping the unit, use the original shipping carton and  
packing materials. For maximum protection, repack the unit as it  
was originally packed at the factory.  
Do not use volatile liquids, such as insect spray, near the unit. Do  
not leave rubber or plastic products in contact with the unit for a  
long time. They will leave marks on the finish.  
The regional number can be found on the rear panel of the DVD  
Player. (e.g.  
1
for Region 1)  
The top and rear panels of the unit may become warm after a  
long period of use.This is not a malfunction.  
When the unit is not in use, be sure to remove the disc and turn off  
the power.  
2. About This Manual  
This manual explains the basic procedures for operating the DVD  
Player. Some DVD-Video discs do not support the full potential of the  
DVD technology. Your DVD Player may therefore not respond to all  
operating commands. Refer to instruction notes on discs.  
If you do not use the unit for a long period, the unit may not  
function properly in the future. Turn on and use the unit  
occasionally.  
A “ ” mark may appear on the TV screen during operation. It means  
that the operation is not permitted by the DVD Player or the disc.  
10. To Obtain a Clear Picture  
3. Warranty Claim  
The unit is a high technology, precision device. If the optical pick-up  
lens and disc drive parts are dirty or worn down, the picture quality  
becomes poor. To obtain a clear picture, we recommend regular  
inspection and maintenance (cleaning or parts replacement) every  
1,000 hours of use depending on the operating environment. For  
details, contact your nearest dealer.  
You can find the serial number on the rear panel of the unit. In case of  
warranty claim, please report this number.  
4. Recording Copyright  
Recording of copyrighted material for other than personal use is illegal  
without permission of the copyright holder.  
11. Notes on Moisture Condensation  
5. Power  
WARNING  
Moisture condensation damages the unit.  
Please read the following carefully.  
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ  
THE FOLLOWING SECTION CAREFULLY.  
What is moisture condensation?  
Moisture condensation occurs, for example, when you pour a cold  
drink into a glass on a warm day. Drops of water form on the outside  
of the glass. In the same way, moisture may condense on the optical  
pick-up lens inside the unit, one of the most crucial internal parts of  
the unit.  
The voltage of the available power supply differs according to country  
or region. Be sure that the power supply voltage of the area where the  
unit will be used meets the required voltage (e.g., AC 120 V, 60 Hz)  
written on the rear panel.  
6. Do not touch the unit with wet hands  
Moisture condensation occurs in the following cases.  
– When you bring the unit directly from a cold place to a warm  
place.  
– When you use the unit in a room where you just turned on the  
heater, or a place where the cold wind from the air conditioner  
directly hits the unit.  
– In summer, when you use the unit in a hot and humid place just  
after you move the unit from an air conditioned room.  
– When you use the unit in a humid place.  
Do not handle the unit or power cord when your hands are wet or  
damp. If water or any other liquid enters the case, take the unit to an  
authorized service center for inspection.  
7. Location of the unit  
Place the unit in a well-ventilated location.  
Take special care to provide plenty of ventilation on all sides of the  
unit especially when it is placed in an audio rack. If ventilation is  
blocked, the unit may overheat and malfunction.  
Do not use the unit when moisture condensation may  
occur.  
Do not expose the unit to direct sunlight or heating units as the unit’s  
internal temperature may rise and shorten the life of the pickup.  
If you use the unit in such a situation, it may damage discs and  
internal parts. Remove the disc, connect the power cord of the unit  
to the wall outlet, turn on the unit, and leave it for two or three  
hours. After a few hours, the unit will have warmed up and  
evaporated any moisture. Keep the unit connected to the wall outlet  
and moisture condensation will seldom occur.  
Avoid damp and dusty places and places directly affected by  
vibrations from the speakers. In particular, avoid placing the unit on  
or above one of the speakers.  
Be sure the unit is placed in a horizontal position. Never place it on  
its side or on a slanted surface as it may malfunction.  
When you place the unit near a TV, radio, or VCR, the playback  
picture may become poor and the sound may be distorted. In this  
case, place the unit away from the TV, radio, or VCR.  
8. Care  
From time to time you should wipe the front and rear panels and the  
cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a  
weak solution of mild detergent and water, wring it out dry, and wipe  
off the dirt. Following this, dry immediately with a clean cloth.  
Do not use rough material, thinners, alcohol or other chemical solvents  
or cloths since these could damage the finish or remove the panel  
lettering.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Important Safeguards / Precautions / Table of Contents............................ 2 - 6  
Getting Started  
Notes on Discs .................................................................................................... 6  
Playable Discs / The Structure of the Disc Content / About Video CDs /  
Handling Discs / Cleaning Discs / Storing Discs / Notes on Copyright  
Features/Supplied Accessories......................................................................... 8  
Features / Supplied Accessories  
Preparing the Remote Controller....................................................................... 9  
Inserting the Batteries / Using the Remote Controller  
Facilities and Connections  
Control Position and Names ............................................................................ 10  
Front Panel / Rear Panel / Display / Remote Controller  
Making Connections ......................................................................................... 14  
Connections to a TV / Optional Video Connections / Optional Audio  
Connections  
Basic Operations  
Turning on.......................................................................................................... 17  
Connecting the POWER  
Basic Playback .................................................................................................. 18  
Starting Playback / Various Playback  
Advanced Operations  
Using Banner Display ....................................................................................... 20  
Using the on-screen Banner Display / Selecting a Title /  
Selecting a Chapter or Track / Selecting a Playback Audio Setting /  
Changing the Subtitle Language / Changing the Camera Angle / Using  
IntroScan function / Using a bookmark  
Other Operations .............................................................................................. 25  
Random Play / Repeat Play / A-B Repeat Play / Memory Edit Play  
Function Setup  
Customizing the Settings ................................................................................. 28  
Making Adjustments to Setting / Language Setting / Operation Setting /  
Picture Setting / Audio Setting  
Table of Languages........................................................................................... 34  
Table of Language and Their Code No.  
Others  
Troubleshooting .................................................................................................. 35  
Specifications ................................................................................ back cover page  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes on Discs  
This section shows you how to handle, clean, and store discs.  
The Structure of the Disc Content  
Playable Discs  
This DVD Player can playback the following discs.  
DVD-Video  
Normally, the contents of DVD-Video are divided into titles, and the  
titles are subdivided into chapters.  
Disc mark  
Contents  
Disc size  
Title 2  
Title 1  
Chapter 1  
12 cm  
Audio  
+
Chapter 1  
Chapter 2  
Chapter 2  
Chapter 3  
DVD-  
Video  
Video  
(moving  
pictures)  
8 cm  
Audio +  
Video  
(moving  
pictures)  
12 cm  
8 cm  
Video CD/CD  
Video CD and CD are divided into tracks.  
Video  
CD  
Track 1  
Track 2  
Track 4  
Track 5  
Track 3  
12 cm  
Audio  
CD  
8 cm (CD single)  
You cannot playback discs other than those listed above.  
You cannot play discs such as CD-ROM, CD-R, CD-RW, DVD-  
Audio, DVD-RAM, DVD-RW, etc., even if the marks in the above  
table are labeled on those discs.  
• This DVD Player uses the NTSC color system, and cannot  
playback video media recorded in any other color system  
(SECAM, etc.).  
• Avoid using heart-shaped or octagonal discs. Playing irregularly  
shaped discs may damage the internal mechanism of the DVD  
Player.  
About Video CDs  
This DVD Player supports Video CDs equipped with the PBC  
(Version 2.0) function. (PBC is the abbreviation of Playback  
Control.) You can enjoy two playback variations depending on the  
type of disc.  
Video CD not equipped with PBC function (Version 1.1)  
Sound and movies can be played on this DVD Player in the same  
way as a CD.  
Discs with shapes such  
as these cannot be  
played.  
Video CD equipped with PBC function (Version 2.0)  
In addition to operation of the Video CD not equipped with the  
PBC function, you can enjoy playback with interactive software  
and search function using the menu displayed on the TV screen  
(Menu Playback). Some of the functions described in this  
Instruction Manual may not work with some discs.  
• Do not use discs that have residue from adhesive tape, rental discs  
that have peeling labels, or discs that have custom labels or  
stickers. Otherwise, you may not be able to eject the discs or the  
DVD Player may become inoperative.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Handling Discs  
Notes on Copyright  
• Do not touch the playback side of the disc.  
It is forbidden by law to copy, broadcast, show, broadcast on cable,  
play in public, and rent copyrighted material without permission.  
The video recorded on DVD-Video is copy protected, and any  
recordings made from these discs will be distorted.  
This product incorporates copyright protection technology that is  
protected by method claims of certain U.S. patents and other  
intellectual property rights owned by Macrovision Corporation and  
other rights owners. Use of this copyright protection technology  
must be authorized by Macrovision Corporation, and is intended for  
home and other limited viewing uses only unless otherwise  
authorized by Macrovision Corporation. Reverse engineering or  
disassembly is prohibited.  
Playback side  
• Do not attach paper or tape to discs.  
Cleaning Discs  
• Fingerprints and dust on the disc cause picture and sound  
deterioration. Wipe the disc from the center outwards with a soft  
cloth. Always keep the disc clean.  
• If you cannot wipe off the dust with a soft cloth, wipe the disc  
lightly with a slightly moistened soft cloth and finish with a dry  
cloth.  
• Do not use any type of solvent such as thinner, benzine,  
commercially available cleaners or antistatic spray for vinyl LPs.  
It may damage the disc.  
Storing Discs  
• Do not store discs in a place subject to direct sunlight or near heat  
sources.  
• Do not store discs in places subject to moisture and dust such as a  
bathroom or near a humidifier.  
• Store discs vertically in a case. Stacking or placing objects on  
discs outside of their case may cause warping.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features/Supplied Accessories  
Features  
1
*
Manufactured under license from Digital Theater Systems, Inc.  
G Plays DVD-Video Discs, Video CDs, CDs  
G 10-bit Video DAC  
G Parallel Video Output  
G Digital Outputs pass DTS®*1, Dolby®*2 Digital and PCM Signals  
G Dolby® Digital decoder Built In  
G Full-function remote controller  
US Pat. No.5,451,942 and other worldwide patents issues and  
pending, DTSand DTS Digital Surroundare trademarks of  
Digital Theater Systems, Inc. ©1996 Digital Theater Systems,  
Inc. All Rights reserved.  
Manufactured under license from Dolby Laboratories.  
Dolbyand the double-D symbol are trademarks of Dolby  
Laboratories. Confidential Unpublished Works. ©1992-1997  
Dolby Laboratories, Inc. All rights reserved.  
2
*
Supplied Accessories  
Make sure your box contains everything listed below.  
If any pieces are missing, contact your nearest Onkyo dealer.  
The number of accessories is indicated in brackets [ ].  
Remote controller (RC-458DV) [1]  
Audio/video cable [1]  
Batteries (size AAA/R3) [2]  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparing the Remote Controller  
Inserting the Batteries  
Using the Remote Controller  
Point the remote controller toward the remote control sensor.  
Remote control sensor  
1
Open the battery compartment cover.  
30˚  
30˚  
2
Insert the two batteries (size AAA/R3).  
Be sure to match the + and ends of the batteries  
with the diagram inside the battery compartment.  
Notes  
Place the unit away from strong light such as direct sunlight or inverted  
fluorescent light which can prevent proper operation of the remote  
controller.  
Using another remote controller of the same type in the same room or using  
the unit near equipment which uses infrared rays may cause operational  
interference.  
Do not put any object such as a book on the remote controller. The buttons  
of the remote controller may be pressed by mistake and drain the batteries.  
Make sure the audio rack doors do not have colored glass. Placing the unit  
behind such doors may prevent proper remote controller operation.  
If there is any obstacle between the remote controller and the remote  
control sensor, the remote controller will not operate.  
3
Close the battery compartment cover.  
Notes  
Do not mix new batteries with old batteries or different kinds of  
batteries.  
To avoid corrosion, remove the batteries if the remote controller  
is not to be used for a long time.  
Remove dead batteries immediately to avoid damage from  
corrosion. If the remote controller does not operate smoothly,  
replace both batteries at the same time.  
The life of the batteries supplied is about six months but this  
will vary depending on usage.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Position and Names  
Front Panel  
For operational instructions, see the page indicated in brackets [ ].  
1 2  
3
4
5
6
7
8
9
0
1 POWER button [17]  
6 PLAY/PAUSE £/8 button [18]  
Turns on the main power supply.  
Begins to play disc (close disc tray first if it is open.)  
Temporarily stops playback when a disc is playing. Press this  
button again for normal playback.  
2 STANDBY indicator [17]  
Lights in the standby mode.  
7 Disc tray [18]  
3
STANDBY/ON button [17]  
8 0 OPEN/CLOSE button [18]  
Toggle for standby on and off.  
Press to open or close the disc tray.  
4 Front panel display [12]  
9 SKIP 4/¢ buttons [19]  
Allow you to move to the previous chapter or track / the next  
chapter or track on a disc.  
5 STOP 7 button [18]  
Stops playing a disc. When disc is playing, if you press 7 and  
£, the disc will start resume play. If you press 7 button twice  
and £ button, disc will start play from the beginning.  
0 SEARCH 1/¡ buttons [19]  
Allow you to search in reverse through a disc while it is in play  
mode. Each time you press this button, search speed changes.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Position and Names  
Rear Panel  
For operational instructions, see the page indicated in brackets [ ].  
VIDEO  
OUTPUT  
COMPONENT  
DIGITAL  
OUTPUT  
ANALOG  
OUTPUT  
P
P
R
DVD PLAYER  
MODEL NO. DV-S353  
OPTICAL COAXIAL  
VIDEO  
L
B
S VIDEO  
Y
R
1 2 3  
4
5 6  
1 DIGITAL OUTPUT OPTICAL jack [16]  
4 VIDEO OUTPUT VIDEO jack [14]  
Connect a video cable to this jack and to the Video Input jack on  
your TV.  
Use optical cable (not provided) to connect you DVD Player to  
a compatible Dolby Digital or DTS receiver or decoder. Dolby  
Digital and DTS offer theater-quality sound (5.1-Channels).  
5 VIDEO OUTPUT S VIDEO jack [15]  
2 DIGITAL OUTPUT COAXIAL jack [16]  
If your TV has a S-Video jack, you can connect an S-Video  
cable to your TV and to your DVD Player for improved video  
quality. The S-Video cable only carries the video signal;  
remember to connect the left and right audio cables.  
Use coaxial cable (not provided) to connect you DVD Player to  
a compatible Dobly Digital or DTS receiver or decoder. Dolby  
Digital and DTS offer theater-quality sound (5.1-Channels).  
3 ANALOG OUTPUT jacks [14]  
6 VIDEO OUTPUT COMPONENT VIDEO (PR/PB/Y)  
Insert audio cables (left and rights) to these jacks on your DVD  
Player and to the corresponding Audio Input jacks (left and  
right) on your TV or receiver.  
jacks [15]  
If your TV has component inputs, you can connect a component  
video cable to your TV and to your DVD Player for ideal video  
quality. The component video cable only carries the video  
signal; remember to connect the left and right audio cables.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Position and Names  
Display  
For operational instructions, see the page indicated in brackets [ ].  
1
2 3 4 5 6 7  
8
9 0 - =  
RESUME  
TITLE  
RANDOM REPEAT  
A-B INTRO MEM.  
MIN  
PBC  
SEC  
DVD  
CD  
CHAPTER TRACK HOUR  
VCD  
~ !  
@
I Display Examples  
1 Inserted disc indicators [18]  
Indicate the type of current disc that is loaded.  
During DVD-Video playback:  
2 Play/Pause indicators [18]  
DVD  
TITLE  
CHAPTER  
MIN  
SEC  
Illuminate in play or pause mode.  
3 Parental Lock indicator [30]  
Playing chapter  
3 of title 2  
Elapsed time of  
the current  
chapter  
Illuminates in parental lock mode.  
Notes  
4 TITLE indicator [26]  
Some discs may not display chapter numbers.  
A time indication not accompanied with a chapter number shows elapsed  
time of a segment within the current time.  
Illuminates to indicate the current title number.  
5 RESUME indicator [18]  
Illuminate when the player is ready for resume playback.  
During Video CD playback:  
TRACK  
MIN  
SEC  
6 CHPTER/TRACK indicators [26]  
VCD  
Indicate display mode of the current chapter of DVD disc or  
track number of Video CD or CD.  
Playing track 3  
Elapsed time of  
the current track  
7 RANDOM indicator [25]  
Note  
Illuminates during random playback.  
Some discs may not display track numbers or elapsed time.  
8 REPEAT indicators [26]  
During CD playback:  
Illuminate during repeat playback.  
TRACK  
MIN  
SEC  
CD  
9 INTRO indicator [23]  
Illuminates during intro-scan playback.  
Playing track 3  
Elapsed time of  
the current track  
0 MEMORY indicator [27]  
Illuminates during program playback.  
- PBC indicator  
Illuminates when PBC is on for VCD.  
= Elapsed time indicator  
Indicate playing time.  
~ Search indicators [19]  
Illuminate during search and slow playback mode.  
! Playback status indicator  
Illuminate (rotating) when the disc plays.  
@ Multifunction indicator (Indicates operating  
status, messages, etc.)  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Position and Names  
Remote Controller  
For operational instructions, see the page indicated in brackets [ ].  
7 MENU button [28]  
Displays the DVD Disc Menu on the TV screen in play mode and  
Setup Menu in stop mode.  
8 ON SCREEN button [20, 27, 28]  
Press this button while youre playing a disc to see Banner  
Display on the screen. The Banner Display contains various  
playback features and gives you the information about the disc  
youre playing.  
1
@
#
$
%
^
2
3
4
5
9 Arrow buttons (5//2/3) [20, 27, 28]  
Use the arrow buttons to select the items or settings.  
0 ENTER button [20, 27, 28]  
Press this button to select and executes a highlighted menu item.  
- TOP MENU button  
When a disc is playing, press this button to see Title Menu on the  
screen. In case of VCD, it will be used for PBC on/off.  
6
7
&
*
(
= AUDIO button [22]  
Press to select various audio languages on a disc.  
8
~ Number buttons (0~9) [29]  
)
Allow to select numbers by pressing these buttons.  
! MEMORY button [27]  
9
Press to see Memory Edit Display on the screen in stop mode.  
@ 0OPEN/CLOSE button [18]  
0
-
Press to open or close the disc tray.  
# SLOW  
/
buttons [19]  
_
+
Allow you to play movie in slow mode. Each time you press this  
button, slow speed will be changed.  
=
$ STEP e/E buttons [19]  
Freeze a picture when a disc is playing. Also the picture advances  
frame by frame each time to press this buttons. In case of VCD,  
reverse STEP can not be activated.  
~
% UP/DOWN 4/¢ buttons [19]  
Allow you to move to the previous chapter or track / the next  
chapter or track on a disc.  
!
¡
^ FR/FF 1/¡ buttons [19]  
Allow you to search in reverse through a disc while it is in play  
mode. Each time you press this button, search speed changes.  
& PLAY £ button [18]  
Begins to play disc (close disc tray first if it is open.)  
* PAUSE 8 button [18]  
Temporarily stops playback when a disc is playing. Press this  
button again for normal playback.  
1
STANDBY ON button [17]  
Toggle for standby on and off.  
( SUBTITLE ON/OFF button [22]  
Turns the subtitles on and off when playing a DVD.  
2 DIMMER button [19]  
) SUBTITLE button [22]  
Toggle to control the lightness of the display (2 steps).  
Press to select various subtitle language on a disc.  
3 RANDOM button [25]  
_ RETURN button [28]  
Press to do random playback.  
When youre using the DVD Players menu system, press this  
button to return to the preceding menu screen.  
4 REPEAT button [26]  
Press to go to the Repeat menu. You can repeat a title, chapter,  
+ ANGLE button [23]  
track or one or entire discs.  
Press to select various camera angles on a disc.  
5 A-B button [26]  
¡ CLEAR button [20]  
Press to play section A-B repeatedly.  
Press to clear entered values and settings. Also Banner menu and  
OSD menu is removed from the screen when this button is pressed.  
6 STOP 7 button [18]  
Stops playing a disc. When disc is playing, if you press 7 and £,  
the disc will start resume play. If you press 7 button twice and £  
button, disc will start play from the beginning.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Making Connections  
To accommodate a wide range of home entertainment systems, this player features numerous connection types for both audio and video. Please  
refer to the instructions on this and the following pages to determine the best possible type of connections for your system.  
Before Connecting  
Refer to the instruction manuals supplied with any and all components that  
you plan to connect the DVD Player to.  
Connect the plugs securely.  
Be sure to turn off the power of all components to be connected and unplug  
them from the wall outlet before making any connections.  
Incomplete  
Connect the DVD Player to the TV or AV component directly. If you connect  
the DVD Player to a VCR, TV/VCR combination, or video selector, the  
playback picture may be distorted as DVD Video images are copy protected.  
Please note that video connections to a TV or monitor are necessary because  
some discs require on-screen menu interaction before they can be played.  
Inserted completely  
Connections to a TV  
The diagram below shows how to make connections to a TV with built-in stereo speakers using the supplied audio/video cable. After making the  
connections on this page, you will be able to start using the DVD Player.  
Be sure to set TV Aspect after connection using the setup menu explained in Customizing the Settingsstarting on  
page 28.  
VIDEO  
OUTPUT  
COMPONENT  
DIGITAL  
OUTPUT  
ANALOG  
OUTPUT  
P
P
R
DVD PLAYER  
MODEL NO. DV-S353  
Connect the power  
cord after all  
OPTICAL COAXIAL  
VIDEO  
L
B
connections are  
complete.  
S VIDEO  
Y
R
To video input  
To audio inputs  
Audio/video cable (supplied)  
Using the supplied audio/video connection  
cable  
Video  
Using the supplied audio/video cable, make audio connections from  
the ANALOG OUTPUT L and R jacks to the corresponding audio  
input jacks on the TV.  
In the same manner, make video connection from the VIDEO  
OUTPUT VIDEO jack to the corresponding video input jack on the  
TV.  
Audio (L)  
Audio (R)  
Analog signal  
Signal flow  
Note  
Be sure to match the colors of the plugs on the cable with the corresponding  
jacks on the DVD Player and the TV: yellow for video, red for R (right)  
audio and white for L (left) audio.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Making Connections  
Optional Video Connections  
Visible improvements in DVD-Video quality can be achieved by making either S-video or component video connections to a TV or monitor  
compatible with these types of connections.  
Note  
When either S-video or component video connection is made, it is not necessary to make composite video connections using the yellow cord of the audio-video  
cable.  
Be sure to set TV Aspect after connection using the setup menu explained in Customizing the Settingsstarting on  
page 28.  
Making S-video connections  
If the TV or monitor has an S-video input, making this type of video  
connection will produce improved picture quality. Using an S-video  
cable, connect the VIDEO OUTPUT S VIDEO jack to the  
corresponding S-video input jack on the TV.  
To S-video inputs  
S-video cable  
(not supplied)  
VIDEO  
OUTPUT  
COMPONENT  
DIGITAL  
OUTPUT  
ANALOG  
OUTPUT  
P
P
R
DVD PLAYER  
MODEL NO. DV-S353  
OPTICAL COAXIAL  
Connect the power  
cord after all  
VIDEO  
L
B
connections are  
complete.  
S VIDEO  
Y
R
To component  
video inputs  
Component video cable  
(not supplied)  
PR  
PB  
Y
Making component video connections  
Component  
signal  
If the TV or monitor has component video inputs, making this type  
of video connection will produce the ideal picture quality for the  
presentation of DVD-Video. Using a componect video cable (sold  
separately), connect the VIDEO OUTPUT COMPONENT jacks to  
the corresponding component video input jacks on the TV.  
Actual labels for component video inputs may vary depending on  
the TV manufacturer. (e.g., Y, R-Y, B-Y or Y, CB, CR)  
S-video signal  
Signal flow  
In some TVs or monitors, the color levels of the playback picture  
may be reduced slightly or the tint may change. In such a case,  
adjust the TV or monitor for optimum performance.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Making Connections  
Optional Audio Connections  
This DVD Player provides numerous ways to take full advantage of the digital multi-channel sound recorded on DVD and some CD media.  
Be sure to set Digital Audio Out after connection using the setup menu explained in Customizing the Settingsstarting  
on page 28.  
Digital connections  
When you are making connections to an amplifier or receiver that  
has internal Dolby Digital or DTS decoding capabilities, set Digital  
Audio Out to Dolby Digitalor DTSusing the setup menu  
explained in Customizing the Settingsstarting on page 28. See  
page 33 for direct information.  
When you are making connections to an amp or receiver that has  
digital input capabilities, but no internal decoder, set Digital Audio  
Out to PCMusing the on-screen menu explained in Customizing  
the Settingsstarting on page 28. See page 33 for direct  
information. Setting Digital Audio Out to any other setting could  
result in digital noise being output that could cause harm your  
hearing and may also damage your speakers.  
Make digital connections from the DVD Player to an AV  
component that features digital input capability or one or more  
multi-channel audio decoders to realize the full cinematic  
experience made possible by the DVD format. This DVD Player  
features optical and coaxial digital audio output jacks and can  
output Dolby Digital and DTS bitstreams as well as outputting  
standard PCM.  
Make connections from the DIGITAL OUTPUT OPTICAL jack to  
the digital optical input jack on the AV component using an optical  
fiber cable (sold separately). Make connections from the DIGITAL  
OUTPUT COAXIAL jack to the digital coaxial input jack on the  
AV component using a coaxial cable (sold separately). It is not  
necessary to make more than one type of digital connection to a  
single component.  
Notes  
Refer to the instructions supplied with the AV component for details on  
what digital audio formats it is compatible with.  
Even if digital audio connections are made, it is also recommended to  
make analog connections, because some conditions or media may prohibit  
digital audio output.  
To digital input  
(optical)  
An amplifier or receiver with a Dolby  
Optical cable (not supplied)  
Coaxial cable (not supplied)  
Digital or DTS decorder or digital  
input jacks  
To digital input  
(coaxial)  
VIDEO  
OUTPUT  
COMPONENT  
DIGITAL  
OUTPUT  
ANALOG  
OUTPUT  
P
P
R
DVD PLAYER  
MODEL NO. DV-S353  
OPTICAL COAXIAL  
DO NOT connect the  
power cord until all  
connections are  
complete.  
VIDEO  
L
B
S VIDEO  
Y
R
To audio input  
An amplifier or receiver  
with stereo inputs  
Audio cable (not supplied)  
Making stereo audio connections  
Audio (L)  
Using an audio cable (sold separately), make audio connections  
from the ANALOG OUTPUT L and R jacks to the corresponding  
jacks on the stereo component.  
Analog signal  
Audio (R)  
Be sure to set Digital Audio Out setting to PCMusing the setup  
menu explained in Customizing the Settingsstarting on page 28.  
See page 33 for direct information.  
Coaxial plug  
Optical plug  
Digital signal  
Digital signal  
Notes  
Be sure to match the colors of the plugs on the cable with the  
corresponding jacks on the DVD Player and the stereo component: red for  
R (right) audio and white for L (left) audio.  
Do not make connections to the PHONO or TUNER jacks on the stereo  
component.  
Signal flow  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turning on  
Connecting the POWER  
Notes  
The DV-S353 is shipped with the main power (POWER) switch in the  
on position ( ON). When the power cord is plugged in for the first  
time, the DV-S353 will automatically enter the standby mode and the  
STANDBY indicator will light (same condition after step 2 below).  
Make sure that all appropriate connections have been completed  
as described on pages 14 to 16.  
Turning on the DVD Player may cause a momentary power surge,  
which might interfere with other electrical equipment such as  
computers. To prevent interference, use a wall outlet on a different  
circuit.  
POWER  
STANDBY/ON  
STANDBY indicator  
1
2
Plug the power cord into  
the power outlet on the  
wall.  
Press POWER to switch  
on the main power.  
The DVD Player enters standby mode.  
The STANDBY indicator lights up.  
STANDBY/ON  
Notes  
The buttons on the remote controller do not operate if  
the POWER switch is set to OFF.  
To switch off the main power, press POWER again.  
3
Press STANDBY/ON  
on the DVD Player or  
remote controller.  
The DVD Player turns on and the STANDBY  
indicator turns off.  
Notes  
You can turn on the DVD player by pressing 0 or £/8.  
To put the DVD Player in the standby mode, press  
STANDBY/ON on the DVD Player, or remote  
controller. Be sure to set the volume to minimum  
before putting the DVD Player in the standby mode for  
the next use to avoid sudden loud sound reproduction.  
While the STANDBY indicator lights up, the DVD  
Player can receive signals from the remote controller.  
However, if you press POWER on the DVD Player to  
switch off the main power, the remote controller  
cannot be used to turn on the DVD Player.  
Setting the STANDBY button to standby does not shut  
off the power completely.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD  
VCD  
CD  
Basic Playback  
Before playing  
Warning  
DVD-Video, Video CD, CD can be played with the DVD Player (see Playable Discson page 6). Do  
not play anything else.  
If the DVD Player is connected to the TV or  
amplifier through the analog audio jacks, do not  
play DTS-encoded discs. Excessive noise may  
be output from the analog stereo jacks, which  
may damage the connected equipment.  
When playing DVD-Video or Video CD with video features, turn on the TV and set the TV to the DVD  
Player's input.  
If an audio system is connected to the DVD Player, turn on the audio system and set it to the DVD  
Players input.  
VCD  
CD  
DVD  
To reproduce DTS surround sounds, digital  
connection to an amplifier with a DTS decoder  
is needed.  
About the  
,
and  
marks in the pages related to disc operation  
DVD  
VCD  
CD  
means the function or title is related to DVD-Video operation.  
means the function or title is related to Video CD operation.  
means the function or title is related to audio CD operation.  
Starting Playback  
STOP 7  
PLAY/PAUSE £/8  
Disc tray  
0 OPEN/CLOSE  
SKIP 4/¢  
SEARCH 1/¡  
I To stop playback  
1
Press 0.  
Press 7.  
The disc tray opens.  
When you press £/8 to restart playback, playback starts  
from the location where you stopped playback because the  
location index is stored in memory.  
If the DVD Player is in standby mode when the  
button is pressed  
The DVD Player turns on and the disc tray opens. In this  
case, it takes several seconds until the disc tray opens.  
Note  
The location where playback resumes may vary depending on the  
disc or the scene where you stopped.  
Resuming playback from the beginning  
Press 7 again after stopping playback to clear the location index  
memory, then press £/8 to start playback.  
2
3
Place a disc on the disc  
tray.  
DVD  
VCD CD  
Playback starts from the beginning of the current title.  
Playback starts from the beginning of the disc.  
Put the disc in the tray with the label side facing up.  
There are two different disc sizes.  
Place the disc in the correct guide on the disc tray.  
To start playback from the beginning of the DVD-Video, press 0 to  
open the disc tray then press £/8 to close the disc tray and start  
playback.  
Press £/8.  
Tip to obtain a higher quality picture  
The disc tray closes and playback starts.  
Occasionally, some picture noise not usually visible during a normal  
broadcast may appear on the TV screen while playing a DVD-Video  
because the high resolution pictures on these discs include a lot of  
information. While the amount of noise depends on the TV you use,  
you should generally adjust the TV to reduce sharpness when viewing  
If you press 0 to close the tray after step 2, playback  
may automatically start depending on the disc.  
The appropriate disc indicator lights.  
For the other information that appears in the  
display, see page 12.  
If the DVD Player is in standby mode when the  
button is pressed  
The DVD Player turns on and playback starts. In this case,  
CAUTION  
Keep your fingers well clear of the disc tray as it is closing.  
Neglecting to do so may cause serious personal injury.  
it takes several seconds until playback starts.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Playback  
Various Playback  
DVD  
VCD  
CD  
I To remove the disc  
Press 0 to open the disc tray.  
OPEN/CLOSE 0  
Remove the disc after the disc tray opens completely.  
After removing the disc, be sure to press the button again to  
close the tray.  
SLOW  
DIMMER  
STEP e/E  
UP/DOWN 4/¢  
FF/FR 1/¡  
I To play in fast reverse or fast forward  
DVD  
VCD  
CD  
During normal playback, press 1/¡.  
Each press of the same button changes the playback speed.  
PLAY £  
PAUSE 8  
(At the time of DVD playback)  
x2 x4 x8 x16 x2 (back to the beginning)  
(At the time of VCD/CD playback)  
x2 x4 x8 x2 (back to the beginning)  
The rate and direction of playback is indicated by search  
indicators (2 or 3) in the display.  
To resume normal playback, press £.  
Notes  
The DVD Player mutes sounds and omits subtitles during reverse  
and forward scan of DVD-Video.  
The playback speed may differ depending on the disc.  
DVD  
VCD  
CD  
I To skip chapters or tracks  
During normal playback, press 4/¢.  
The chapter (or track) in the direction of the key pressed is  
skipped, and the selected chapter (or track) will be played  
from the beginning.  
When 4 is pressed once during playback, the chapter (or  
track) being played will be played from the beginning  
DVD  
VCD  
I To pause playback (still mode)  
Press 8 during playback.  
To start playback, press £.  
DVD  
VCD  
I Playing frame by frame  
Press 28/83 repeatedly during pause.  
Each time you press the button the picture advances one  
frame.  
To resume normal playback, press £ .  
I Using DIMMER function  
Note  
The sound is muted during still mode and frame by frame playback.  
Press DIMMER to change the display brightness.  
Each time DIMMER is pressed, the display brightness of the unit  
changes as shown below.  
DVD  
VCD  
I To play in slow-motion  
Normal Dim  
Press  
/
during playback.  
Each press of the same button changes the playback speed.  
x1/16 x1/8 x1/4 x2/1 x1/16 (back to the beginning)  
The rate and direction of playback is indicated by search  
indicators (2 or 3) in the display.  
Notes  
Do not move the DVD Player during playback. Doing so may damage  
the disc.  
Use 0 on the remote controller or DVD Player to open and close the disc  
tray. Do not touch the disc tray while it is moving. Doing so may cause  
the DVD Player to malfunction.  
Do not press down on the disc tray or put any objects other than playable  
discs on the disc tray. Doing so may cause the DVD Player to  
malfunction.  
To resume normal playback, press £.  
Notes  
The sound is muted during slow-motion playback.  
The playback speed may differ depending on the disc.  
In many instances, a menu screen appears when playback of a DVD  
movie is complete. Prolonged display of an on-screen menu may damage  
your television set, permanently etching that image onto its screen. To  
avoid this, be sure to press 7 once the movie is complete.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD  
VCD  
CD  
Using Banner Display  
DVD  
VCD  
CD  
Using the on-screen Banner Display  
The on-screen Banner Display contains many playback features.  
To see the Banner Display, press ON SCREEN on the remote  
while a disc is playing. Use 2/3 to move through the different  
features in the Banner Display. Each feature is illustrated with an  
icon.  
During playback, press ON  
1
SCREEN.  
The Banner Display appears on the screen.  
When playing a DVD  
Chapter  
Title  
Subtitles  
Audio Angles  
Bookmarks  
Disc Type  
ON SCREEN  
SUBTITLE ON/OFF  
SUBTITLE  
Time Indicator  
2/3/5/∞  
When playing a VCD  
ENTER  
Introscan  
Time Information  
Track  
Bookmarks  
Disc Type  
AUDIO  
ANGLE  
CLEAR  
Time Indicator  
When playing a CD  
IntroScan  
Time Information  
Track  
Bookmarks  
Disc Type  
Time Indicator  
Press 2/3 to select a desired item,  
and press ENTER.  
Corresponding menu appears on the screen.  
2
«
To turn off the Banner Display  
Press ON SCREEN or CLEAR.  
Notes  
You can only access the banner display when youre playing a disc.  
The banner display features are only available if the disc was created  
with that particular feature (i.e., if you select the Subtitle icon, you wont  
be able to change the subtitle language unless the author of the disc  
created the disc with subtitles).  
The invalid symbol  
appears on the screen when you press a button  
that doesnt have any function. If one of the icons is glayed out,the  
banner feature isnt available for the disc youre playing.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Banner Display  
DVD  
VCD  
CD  
DVD  
Selecting a Title  
Selecting a Chapter orTrack  
DVD-Video  
DVD-Video  
Title 1  
Chapter 1 Chapter 2  
Title 2  
Chapter 2  
Title 1  
Title 2  
Chapter 3  
Chapter 1  
Some discs contain more than one title. For example, there might  
be four movies on one disc (each movie might be considered a  
title).  
Video CD/CD  
Track 1  
Track 2  
Track 4  
Track 5  
Track 3  
Press ON SCREEN.  
1
Because DVD discs use digital technology, a title can be divided  
into individual chapters (similar to tracks on a CD). You can skip a  
specific chapter by using the Chapter section in the Banner  
Display.  
Press 2/3 until the TITLE icon is  
highlighted.  
2
Press ON SCREEN.  
1
«
Press 2/3 until the CHAPTER or  
TRACK icon is highlighted.  
2
Press ENTER.  
3
__  
T appears.  
«
Press the numeric buttons to enter  
the title number.  
4
When you enter a one-digit title number, you  
may have to press ENTER on the remote after  
pressing the number (1~9) on the remote.  
Otherwise press 0 first and the other value.  
Then play starts. This varies depending on  
number of title within the disc youre playing.  
Press ENTER.  
3
__  
__  
C or Tr appears.  
Press the numeric buttons to enter  
the title number.  
4
Note  
Some discs only have one title.  
When you enter a one-digit chapter or track  
number, you may have to press ENTER on  
the remote after pressing the number (1~9) on  
the remote. Otherwise press 0 first and the  
other value. Then play starts. This varies  
depending on number of chapter or track  
within the disc youre playing.  
Note  
The chapter feature wont work if the disc isnt formatted with separate  
chapters.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Banner Display  
DVD  
DVD  
Selecting a Playback Audio Setting  
Changing the Subtitle Language  
Good morning!  
Bon jour!  
¡Buenos días!  
Good evening!  
Bon soir!  
¡Buenas tardes!  
You can select the preferred audio language and sound system as a  
set from those included on the disc. This function lets you  
temporarily change the audio language which you selected as the  
automatic setting in the setting menu (see pages 28 and 29), and  
choose the sound system if the disc is recorded in more than one  
sound format.  
You can display subtitles on the TV screen and select a subtitle  
language from those included on the DVD-Video.  
Press On SCREEN during playback.  
1
Press On SCREEN during playback.  
1
Press 2/3 until the SUBTITLE icon  
is highlighted.  
2
Press 2/3 until the AUDIO icon is  
highlighted.  
2
Press ENTER.  
3
The subtitle menu appears.  
Displayed when  
SUBTITLE is on  
Press ENTER.  
The audio menu appears.  
3
Press ENTER to select the subtitle  
4
language.  
Press ENTER to select the audio.  
Each time you press ENTER, the subtitle  
4
Each time you press ENTER, the audio  
language changes.  
recording system set changes.  
Press SUBTITLE ON/OFF to select  
5
subtitle on or off.  
Switching between display of subtitles and no  
display of subtitle is done each time the key is  
pressed.  
To turn off the audio menu  
Press ON SCREEN or CLEAR.  
The menu is switched off when no operation is performed for  
about 3 seconds.  
To turn off the subtitle menu  
Using AUDIO on the remote  
Press ON SCREEN or CLEAR.  
The menu is switched off when no operation is performed for  
about 3 seconds.  
1 Press AUDIO on the remote during playback.  
2 Press AUDIO or ENTER to select the audio language.  
Using SUBTITLE on the remote  
Notes  
Dolby Digital 5.1 Channel sound may bedisplayed as 6ch. Dolby  
Digital.  
1 Press SUBTITLE on the remote during playback.  
Before changing the setting, read through the explanation on Digital  
Audio Outon page 33 and carefully select the setting.  
Depending on the disc, it may be necessary to select the audio sound  
track using the DVD menu. When this is the case, press MENU to open  
the DVD menu and select the appropriate sound track as indicated on the  
DVD menu screen.  
When the DVD Player is turned on or when the disc is changed, the  
audio settings are restored to the presets. In some cases, a language  
recorded on the disc may be given priority and selected automatically  
when the disc is loaded regardless of the setting.  
2 Press SUBTITLE or ENTER to select the subtitle language.  
3 Press SUBTITLE ON/OFF to select sub title on or off.  
Notes  
When you turn on the DVD Player or replace a disc, the DVD Player  
returns to the automatic setting in the setting menu (see pages 28 and  
29).  
When you select a subtitle language which is not included on the disc,  
the DVD Player plays the prior language programmed on the disc.  
During some scenes, the subtitles may not appear immediately after you  
change the subtitle setting.  
Some DVD-Video are set to display subtitles automatically, and you  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Banner Display  
VCD  
CD  
DVD  
Changing the Camera Angle  
Using IntroScan function  
Track : 1  
Track : 2  
Track : 3  
Angle : 1  
Angle : 2  
Angle : 3  
If the scene was recorded from multiple angles, you can easily  
change the camera angle of the scene you are watching.  
IntroScan plays the first few seconds of each track on the Video CD  
or CD similar to the scan feature that's on many car radios.  
Press On SCREEN during playback.  
Press ON SCREEN during  
playback.  
1
1
Press 2/3 until the SUBTITLE icon  
is highlighted.  
Press 2/3 until the IntroScan icon  
is highlighted.  
2
2
Press ENTER.  
The angle menu appears.  
3
Press ENTER.  
3
The first 10 seconds of each track will be  
played.  
Press £ to stop IntroScan playback and start  
playing the current track entirely.  
Press ENTER to select the angle.  
Each time you press ENTER, the angle  
4
changes.  
Note  
After IntroScan goes through all of the tracks, it stops.  
To turn off the angle menu  
Press ON SCREEN or CLEAR.  
The menu is switched off when no operation is performed for  
about 3 seconds.  
Using ANGLE on the remote  
1 Press ANGLE on the remote during playback.  
2 Press ANGLE or ENTER to select the audio language.  
Notes  
You can change the camera angle during still playback. The camera  
angle changes to the new setting when you resume normal playback.  
If you pause a picture immediately after changing the camera angle, the  
resumed playback picture may not use the new camera angle.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Banner Display  
DVD  
VCD  
CD  
Using a bookmark  
The bookmark feature lets you mark a point on the disc that you can  
go to quickly. You can store up to 9 bookmarks.  
Recalling a bookmarked scene  
Marking a scene  
Press ON SCREEN during  
playback.  
Press ON SCREEN during  
1
1
2
playback.  
Press 2/3 until the bookmark icon  
Press 2/3 until the bookmark icon  
2
is highlighted and press ENTER  
is highlighted and press ENTER  
The bookmark menu appears.  
The bookmark menu appears.  
«
«
When you reach the scene you  
3
want to mark, press ENTER.  
Press 5 to go the parts of the  
3
4
The bookmark appears on under square.  
You can store up to 9 bookmarks by repeating  
this step.  
bookmark menu.  
Press ON SCREEN or CLEAR to  
4
make the Banner display disappear  
Press 2/3 to select the  
bookmarked scene you want to  
activate.  
from the screen.  
Press ENTER to activate the  
bookmark.  
5
To clear the bookmark  
The bookmark is cleared each time a disc is removed from the  
player or when the power is turned off.  
To turn off the bookmark menu  
Press ON SCREEN or CLEAR.  
The menu is switched off when no operation is performed for  
about 3 seconds.  
Notes  
• If all 9 bookmarks are in use, you can still mark new scenes, but the  
previous bookmarks will be erased.  
• Depending on the disc, the bookmark function may not work.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD  
VCD  
CD  
Other Operations  
DVD  
VCD  
CD  
The following operations can be performed directly from the  
remote controller.  
Random Play  
Repeat Play  
Random play  
TiItTleLE: 1: 1  
A-B Repeat Play  
Memory Edit Play  
CHhaApPteTrE:R3: 3  
Title : 2  
Title : 3  
Chapter : 2  
Chapter : 1  
The chapters or tracks of the disc are played in random order.  
Press RANDOM.  
The random playback starts.  
Lights  
Display  
RANDOM  
REPEAT  
A-B  
RANDOM  
The Random Play display appears on the  
screen.  
ON SCREEN  
2/3/5/∞  
To turn off the Random Play display  
ENTER  
Press ON SCREEN or CLEAR.  
The menu is switched off when no operation is performed for  
about 3 seconds.  
Note  
Numeric  
buttons  
When playing a DVD, the Random function may not work.  
To cancel random play  
CLEAR  
MEMORY  
Press RANDOM so that RANDOM goes off or to select Standard  
Play.  
Each time you press RANDOM, random play will be on and off.  
Random Play Standard Play  
The Standard Play display appears when random is off.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other operations  
DVD  
DVD  
VCD  
CD  
VCD  
CD  
Repeat play  
A-B Repeat play  
A
B
The A-B repeat function lets you mark a segment to repeat between  
the beginning Aand the end Bof the segment you want to  
replay.  
Desired disc or title can be played back repeatedly.  
There are four repeat options:  
Disc  
Title  
Repeat the disc that is playing.  
Repeat the title that is playing.  
Press A-B when you want to  
Chapter Repeat the chapter that is playing.  
Track Repeat the track that is playing.  
1
choose a scene (sound) as the  
beginning point.  
Display  
Lights  
Press REPEAT repeatedly during  
REPEAT  
A-  
playback.  
The Repeat display appears on the screen.  
The Repeat A- display appears on the screen.  
Each time you press REPEAT, the repeat  
option changes.  
At the time of DVD playback  
Press A-B again to choose a scene  
(sound) as the end point.  
Repeat Disc  
Repeats the current chapter.  
Repeats the current title.  
Repeats the entire disc.  
2
The Repeat A-B display appears.  
Repeat Title  
Lights  
Display  
Repeat Chapter  
REPEAT  
A-B  
Repeat Off  
Resumes normal playback.  
At the time of VCD/CD playback  
Repeat Disc  
Repeats the current chapter.  
The DVD Player automatically returns to  
point A and starts repeat playback of the  
selected segment (A-B).  
Repeat Track  
Repeats the current track.  
Resumes normal playback.  
Repeat Off  
To turn off the Repeat A-B display  
To turn off the Repeat display  
Press ON SCREEN or CLEAR.  
The menu is switched off when no operation is performed for  
about 3 seconds.  
Press ON SCREEN or CLEAR.  
The menu is switched off when no operation is performed for about  
3 seconds.  
To cancel A-B Repeat playback  
To cancel repeat playback  
Press A-B so that A-B REPEAT goes off or to select Repeat off.  
Press REPEAT so that REPEAT goes off or to select Repeat Off.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other operations  
DVD  
VCD  
CD  
Memory Edit Play  
Title : 2  
Title : 2  
Title : 1  
Chapter : 25  
Chapter : 12  
Chapter : 1  
The DVD Player automatically plays titles, chapters, or tracks in  
the order you program.  
To delete memory  
Press MEMORY during stop mode.  
The MEMORY EDIT display appears.  
1
1 Press MEMORY during stop mode.  
2 Move the cursor with 3 to the Playlistand press 5/to  
select the column to be deleted from the Playlist. (The color of  
the column where the cursor is located will change.)  
3 Press 2 and press 5/to move the cursor to the Delete button  
on the screen, and press ENTER.  
Insert chapter or track  
1 Press MEMORY during stop mode.  
The MEMORY EDIT display appears.  
Press 5/or numeric buttons to  
select specific title/chapter or  
track.  
2
Press ENTER.  
3
2 Press 5/or numeric buttons to select specific title/chapter or  
track.  
3 Move the cursor with 3 to the Playlistand press 5/to  
select the column to be added.  
The cursor of the column where the cursor is located will  
change.  
4 Press 2 to move the cursor to the Insert button on the screen and  
press ENTER.  
Select Add button on the screen to  
4
register selected value onto  
Playlist, then press ENTER.  
The new chapter or track will be insert before (above) the  
selected column.  
You can select maximam 32 values  
by repeating steps 2-4.  
5
To cancel memory playback  
In following cases, Memory play would be released.  
1 When you open and close tray.  
2 When you press 7 twice.  
Press Play button or £ on the unit  
6
or remote controller to start  
3 When you turn power off.  
playback.  
Notes  
When you dont add values onto Playlist and return to play mode, select  
Done button and press ENTER on the remote.  
While a disc is playing, press MEMORY on the remote to start memory  
play.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD  
VCD  
CD  
Customizing the Settings  
When you insert a DVD-Video, Video CD, or CD, the  
various functions of the DVD Player will be set (reset)  
according to the setting menu.  
You can customize this setting menu according to your  
preferences.  
DVD  
VCD  
CD  
Making Adjustments to Setting  
Press MENU during stop mode.  
Current setup menu display appears.  
1
MENU  
2/3/5/∞  
Press 5/to select the item you  
want to change, then press ENTER.  
2
ENTER  
RETURN  
Numeric  
buttons  
«
CLEAR  
Press 5/to change the setting,  
3
then press ENTER.  
Further steps may be needed depending on the  
item or setting. Follow the steps described in  
the explanation of each item starting from page  
29.  
«
Repeat steps 2 to 3 to change the  
setting of other items.  
4
Press MENU to turn off the setup  
menu display.  
5
How to use RETURN  
When RETURN is presseed, the display returns to the previous  
screen (stop mode).  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Settings  
Language-related settings  
Language Setting  
English: To display subtitles in English.  
Spanish: To display subtitles in Spanish.  
DVD  
Audio Language  
French: To display subtitles in French.  
Others: To make a further choice. Follow steps 1 - 3 below.  
This sets the language to be used when playing a disc. If a disc  
does not contain the selected language, it is played in the priority  
language set for each disc.  
1
2
3
Select Otherand press ENTER.  
Press the numeric buttons to enter the 4-digit code.  
Select OK button and press ENTER.  
Notes  
Some DVD-Video may be set to display subtitles in a different language  
than you selected. A prior subtitle language may be programmed on the  
disc.  
Some DVD-Video allow you to change subtitle selections only via the disc  
menu. If this is the case, Press MENU and choose the appropriate subtitle  
language from the selection on the disc menu.  
DVD  
Menu Language  
English: To play sound tracks in English.  
Spanish To play sound tracks in Spanish.  
French: To play sound tracks in French.  
This sets the initial setup of language as well as the language used  
in on-screen messages such as PLAY.  
Others: To make a further choice. Follow steps 1 - 3 below.  
1
2
3
Select Otherand press ENTER.  
Press the numeric buttons to enter the 4-digit code.  
Select OK button and press ENTER.  
Note  
Depending on the disc, a language recorded on the disc may be given priority  
and selected automatically when the disc is loaded regardless of the setting.  
DVD  
Subtitle Language  
English: To display disc menus in English.  
Spanish: To display disc menus in Spanish.  
French: To display disc menus in French.  
This sets the language to be used when playing a disc. If a disc  
does not contain the selected language, it is played in the priority  
language set for each disc.  
Note  
Some DVD-Video may not include your pre-selected language. In this case,  
the DVD Player automatically displays disc menus consistent with the discs  
initial language setting.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Settings  
General utility settings  
Operation Setting  
To input password  
DVD  
Rating  
1
2
Select “Set Password”.  
This can restrict playback of adult-oriented DVD discs that you do  
not want to be seen by children.  
Press the numeric buttons to enter password.  
However, even when a DVD disc is marked “Adult-oriented” or so  
on the label, its viewing cannot be restricted unless the restriction  
level is recorded in the disc itself.  
3
Select OK button and press ENTER.  
Confirm Password display appears below Enter Password  
display.  
You cannot play DVD Video rated higher than the level you selected unless  
you cancel the parental lock function.  
For example, when you select level 7, discs rated higher than level 7 are  
locked out and cannot be played.  
The Rating level is equivalent to the following U.S. movie ratings.  
Level 7:  
Level 6:  
Level 4:  
Level 3:  
Level 1:  
NC-17  
R
PG 13  
PG  
G
Notes  
DVD-Video may or may not respond to the parental lock setting. This is not a  
defect in the DVD Player. Make sure this function works with your DVD-Video.  
4
Press the numeric buttons to enter password.  
• When the password already has been set, the screen for change of the  
entered password will be displayed. In that case, enter the password (See  
“Password” below).  
DVD  
Password  
The password for rating setting, change, cancellation, etc. is set.  
5
Select OK button and press ENTER.  
Note  
Be sure not to forget your password. If you should forget it, press  
STANDBY/ON and 4 on the unit simultaneously to clear the  
password. If the display on the unit disappears with this operation,  
press the POWER switch on the unit and then press it again to  
recover the display.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Settings  
Operation Setting (continued)  
To change password  
6
Press the numeric buttons to enter new password.  
1
2
Press the numeric buttons to enter password.  
7
Select OK button and press ENTER.  
Select OK button and press ENTER.  
Password setup menu appears.  
To clear password  
3
Select Change Password.  
Enter Password menu appears.  
1
2
Press the numeric buttons to enter password.  
Select OK button and press ENTER.  
4
5
Press the numeric buttons to enter new password.  
Password setup menu appears.  
Select OK button and press ENTER.  
Confirm Password display appears below Enter Password  
display.  
3
Select Clear Passwordand press ENTER.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Settings  
Audio output setting  
Picture-related setting  
Picture Setting  
Audio Setting  
Dynamic Range  
DVD  
DVD  
TV Aspect  
Dynamic Range setting allows you to compressthe dynamic  
range of a DVDs sound track, so that you can lower the volume  
without losing extremely soft signals. This is especially useful  
when you are watching a movie late at night.  
This sets the screen size (4:3 or 16:9 aspect ratio) according to the  
connected TV.  
4 x 3 Letterbox:  
Choose this setting if you would  
prefer to see movies in their  
original aspect ratio. You will see  
the entire frame of the movie,  
but it will occupy a smaller  
portion of the screen. This  
Off:  
On:  
Full dynamic range is maintained.  
Dynamic range is reduced.  
Notes  
This function works only during playback of Dolby Digital recorded discs.  
The level of Dynamic Range Reduction may differ depending on the DVD.  
setting may result in the movie  
appearing with black bars at the  
top and bottom of the screen.  
4 x 3 Pan Scan:  
Choose this setting if you want  
the movie to fill the entire screen  
of your TV. You wont see part  
of the picture (particularly the  
right and left edge).  
Some disc produced in a wide  
screen format cant be cropped in  
this fashion, which means the  
black bars would appear at the  
top and bottom of the screen.  
16 x 9 Widescreen:  
Choose this setting if your DVD  
Player is connected to a  
widescreen TV.  
Notes  
The displayable picture size is preset on each DVD-Video. Therefore, the  
playback picture of some DVD-Video may not conform to the picture size  
you select.  
When you play a DVD-Video recorded in the 4:3 picture size only, the  
playback picture always appears in the 4:3 picture size regardless of the TV  
shape setting.  
If you select 16:9 Widescreenand you own a 4:3 TV set, the DVD  
playback picture will be horizontally distorted during playback. Images  
will appear to be horizontally compressed. Make sure the TV Shape  
conforms to the actual TV in use.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Settings  
Audio Setting (continued)  
DOLBY DIGITAL Surround  
DVD  
VCD  
CD  
Digital Audio Out  
DVD Video that have the  
mark are recorded using this system.  
mark are recorded using this system.  
D
I
G
I
T
A
L
This sets the type of audio output from the digital audio output jack.  
DTS Surround  
DVD Video and CD that have the  
Important: DTS information  
If you set the Digital Audio Out setting to DTS, you must have your DVD  
player connected to a receiver or decoder with the DTS feature and the disc  
you play must support the DTS audio format. If you choose DTS and your  
receiver, decoder or disc doesnt support DTS, you wont hear any audio  
when you play the disc.  
DVD  
VCD  
CD  
Linear PCM  
PCM:  
Select when connected to a 2 channel digital stereo  
amplifier (see page 16).  
The DVD Player outputs sounds in the PCM format  
when you play a DVD-Video disc recorded on the  
Dolby Digital.  
The DVD Player does not output sounds in the  
PCM format when you play a DVD-Video disc  
recorded on the DTS recording system.  
Dolby Digital: Select when you connected to an amplifier  
equipped with a Dolby Digital decorder (see page  
16).  
The DVD Player outputs digital audio information  
in the Dolby Digital format when you play a DVD-  
Video recorded in the Dolby Digital recording  
system.  
The DVD Player does not output sounds in the  
PCM format when you play a DVD-Video disc  
recorded on the DTS recording system.  
96KHz 48KHz: Even in case of 96 kHz digital signal, the  
DVD player will deliver 48 kHz signal out.  
96KHz 96KHz: In case of 96 kHz digital signal, the DVD  
player will deliver 96 kHz signal out. In this case, your  
receiver should control 96 kHz signal.  
DTS:  
Select when you connected to an amplifier  
equipped with a DTS decorder (see page 16).  
The DVD Player outputs digital audio information  
in the DTS format when you play a DVD-Video  
recorded in the DTS recording system.  
The DVD Player outputs sounds in the Dolby  
Digital format when you play a DVD-Video disc  
recorded on the Dolby Digital recording system.  
Dolby Digital and DTS  
The 5.1-channel digital surround format of DOLBY DIGITAL/DTS enables  
you to individually play five full-range (20 Hz-20 kHz) channels (left and  
right front, center, two surround channels) plus an LFE (Low Frequency  
Effect) channel for the low-range effect sound. It will create a realistic sound  
as heard in theaters and concert halls.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Languages  
Table of Languages and Their Code No.  
Code No.  
Language  
Code No.  
Language  
Code No.  
Language  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Ameharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Basque  
Bengali; Bangla  
Bhutani  
Bihari  
Russian  
Samoan  
Sangho  
Sanskrit  
Scots Gaelic  
Serbian  
Servo-Groatian  
Sesotho  
Setswana  
Shona  
6566  
6565  
6570  
8381  
6577  
6582  
7289  
6583  
6588  
6590  
6665  
6985  
6678  
6890  
6672  
6673  
6682  
6671  
7789  
6669  
7577  
6765  
9072  
6779  
7282  
6783  
6865  
7876  
6978  
6979  
6984  
7079  
7074  
7073  
7082  
7089  
7176  
7565  
6869  
6976  
7576  
7178  
7185  
7265  
7387  
7273  
7285  
7383  
7378  
7365  
7369  
7375  
7165  
7384  
7465  
7487  
7578  
7583  
7575  
8287  
7589  
8278  
7579  
7585  
7679  
7665  
7686  
7678  
7684  
7775  
7771  
7783  
7776  
7784  
7773  
7782  
7779  
7778  
7865  
7869  
7879  
7967  
7982  
7977  
8065  
8083  
7065  
8076  
8084  
8185  
8277  
8279  
Hungarian  
Icelandic  
Indonesian  
Interlingua  
Interlingue  
Iunpiak  
8285  
8377  
8371  
8365  
7168  
8382  
8372  
8384  
8478  
8378  
8368  
8373  
8383  
8375  
8376  
8379  
6983  
8385  
8387  
8386  
8476  
8471  
8465  
8484  
8469  
8472  
6679  
8473  
8479  
8483  
8482  
8475  
8487  
8575  
8582  
8590  
8673  
8679  
6789  
8779  
8872  
7473  
8979  
9085  
Irish  
Italian  
Japanese  
Javanese  
Kannada  
Kashmiri  
Kazakh  
Kinyarwanda  
Kirghiz  
Kirundi  
Korean  
Kurdish  
Laothian  
Latin  
Latvian, Lettish  
Lingala  
Lithuanian  
Macedonian  
Malagsy  
Malay  
Malayalam  
Maltese  
Maori  
Marathi  
Moldavian  
Mongolian  
Naru  
Nepali  
Norwegian  
Occitan  
Oriya  
Oromo (Afan)  
Panjabi  
Pashto, Pushto  
Persian  
Polish  
Portuguese  
Quechua  
Rhaero-Romance  
Romanian  
Sindhi  
Singhalese  
Siswati  
Slovak  
Slovenian  
Somali  
Spanish  
Sundanese  
Swahili  
Swedish  
Tagalog  
Tajik  
Tamil  
Tatar  
Telugu  
Thai  
Tibetan  
Tigrinya  
Tonga  
Tsonga  
Turkish  
Turkmen  
Twi  
Ukrainian  
Urdu  
Uzbek  
Vietnamese  
Volapuk  
Welsh  
Wolof  
Xhosa  
Bislama  
Breton  
Bulgarian  
Burmese  
Byelorussian  
Cambodian  
Catalan  
Chinese  
Corsican  
Croatian  
Czech  
Danish  
Dutch  
English  
Esperanto  
Estonian  
Faroese  
Fiji  
Finnish  
French  
Frisian  
Galician  
Georgian  
German  
Greek  
Greenlandic  
Guarani  
Gujarati  
Hausa  
Yiddish  
Yoruba  
Zulu  
Hebrew  
Hindi  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Check the following guide for the possible cause of a problem before contacting service. Refer also to the respective instruction manuals of the  
connected components and TV.  
Symptoms  
Causes  
Remedies  
Pages  
The DVD Player doesnt  
switch on.  
The power cord is disconnected.  
The main power is set to OFF.  
There is external noise in the computer  
circuits of the DVD Player.  
Check the connection of the power cord.  
Turn on the main power.  
Switch off the main power, then switch it on  
again. If not recovered, disconnect the power  
cord, then connect it again.  
17  
17  
17  
The AC fuse is blown.  
Contact your nearest Onkyo service center.  
The DVD Player doesnt start No disc is inserted.  
playback.  
Insert a disc. (Check that DVD,” “VCD,or  
CDis lit in the DVD Players display).  
18  
4
The region number of the disc does not match See 1. Regional Restriction Codes (Region  
that of the DVD Player.  
Number)on page 4.  
Check the playable discs.  
Place the disc with the playback side down.  
Place the disc within the proper guide on the  
disc tray.  
An unplayable disc is inserted.  
The disc is placed upside down.  
The disc is not placed within the disc tray  
guide.  
6
18  
18  
The disc is dirty.  
The parental lock function is activated.  
Eject the disc and clean it.  
Deactivate the parental lock function or  
change the parental lock level.  
7
30  
Brightness is unstable or noise Copy protection is activated.  
is visible on the playback  
picture.  
Connect the DVD Player directly to the TV.  
Avoid connecting the DVD Player to the TV  
through a VCR.  
14  
The playback picture is  
occasionally distorted.  
The disc is dirty.  
It is in fast forward or fast reverse playback.  
Eject the disc and clean it.  
Sometimes a small amount of picture  
distortion may appear. This is not a  
malfunction.  
7
Playback doesnt follow the  
course of the discs programs.  
The DVD Player is in repeat playback mode,  
memory playback mode, or random playback  
mode, etc.  
Resume normal playback.  
18  
The picture from the DVD  
Player doesnt appear on the  
TV screen.  
The TV is not set to receive the output signals Set the TV to the DVD Players input.  
from the DVD Player.  
The DVD Player is not properly connected.  
Check the connections to the DVD Player.  
14, 15  
No sound or inaccurate sound A wrong sound signal conversion method  
Check the current sound signal conversion  
method, and select the right setting for  
Digital Audio Out.  
33  
is reproduced.  
(Digital Audio Out) is selected.  
The TV is not set to receive the output signals Set the TV to the DVD Players input.  
from the DVD Player.  
The DVD Player is not properly connected.  
Check the connections to the DVD Player.  
14-16  
17  
The buttons on the remote  
controller and DVD Player do  
not operate.  
Power supply fluctuations or other  
abnormalities such as static electricity may  
interrupt correct operation.  
Switch off the main power, then switch it on  
again. If not recovered, disconnect the power  
cord, then connect it again.  
The buttons on the DVD  
Player operate but the buttons  
on the remote controller do  
not operate.  
No batteries are inserted in the remote  
controller.  
The batteries are worn out.  
The remote controller is not pointed at the  
remote sensor of the DVD Player.  
Insert new batteries.  
9
Replace with new batteries.  
Point the remote controller at the remote  
sensor of the DVD Player.  
9
9
The remote controller is too far from the DVD Operate the remote controller within 5 m  
Player. (16 feet).  
9
Because the unit contains a microcomputer to provide advanced functions, it may malfunction due to external noise or static electricity. If  
this happens, press the POWER switch on the unit and then press it again after about five seconds.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
DVD Player  
Power supply  
AC 120 V, 60 Hz  
Power consumption  
Weight  
16 W  
8.2 lbs  
External dimensions  
Signal system  
17 1/8" x 3 7/8" x 12 11/16" (W/H/D)  
NTSC  
Frequency range (digital audio)  
DVD linear sound:  
48 kHz sampling 4 Hz to 22 kHz  
96 kHz sampling 4 Hz to 44 kHz  
Signal-to-noise ratio (digital audio)  
Audio dynamic range (digital audio)  
Harmonic distortion (digital audio)  
Wow and flutter  
More than 95 dB  
More than 95 dB  
Less than 0.005 %  
Below measurable level  
Operating conditions  
Temperature: 5°C to 35°C (41°F to 95°F), Operation status: Horizontal  
Outputs  
Video output  
1.0 V (p-p), 75 , negative sync., pin jack × 1  
S-video output  
(Y) 1.0 V (p-p), 75 , negative sync., Mini DIN 4-pin × 1  
(C) 0.286 V (p-p), 75 Ω  
Component video output  
(Y) 1.0 V (p-p), 75 , negative sync., pin jack × 1  
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack × 2  
Audio output (digital output Optical)  
Audio output (digital output Coaxial)  
Audio output (2-Channel Audio)  
Optical connecter × 1  
0.5 V (p-p), 75 , pin jack × 1  
2.0 V (rms), 320 , pin jack (L, R) × 1  
Supplied Accessories  
Audio/video connection cable  
Remote controller (RC-458DV)  
Batteries (size AAA/R3)  
1
1
2
Specifications and features are subject to change without notice.  
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN  
Tel: 072-831-8111 Fax: 072-833-5222  
ONKYO U.S.A. CORPORATION  
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.  
Tel: 201-785-2600 Fax: 201-785-2650 E-mail: [email protected]  
ONKYO EUROPE ELECTRONICS GmbH  
Industriestrasse 20, 82110 Germering, GERMANY  
Tel: 089-849-320 Fax: 089-849-3265 E-mail: [email protected]  
ONKYO CHINA LIMITED  
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,  
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039  
HOMEPAGE  
E
SN 29343126  
W0104-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miller Electric Welding System Big Blue 402P User Manual
Multiquip Automobile Parts MT54F User Manual
Multitech Modem MT5634ZBA V92 User Manual
Musical Fidelity Stereo Amplifier M3I User Manual
NAD Stereo Receiver T742 User Manual
NEC Network Card NDA 24233 User Manual
NEC Speaker SP4020 User Manual
NuTone Ventilation Hood PFCH42 User Manual
Onkyo Stereo System TXNR808 User Manual
Panasonic Air Conditioner CW XC83YU User Manual