Onkyo DVD Player DV BD507 User Manual

Contents

BLU-RAY DISC PLAYER

Introduction............................................................ 2

DV-BD507

Connections............................................................ 13

Playback..................................................................... 19

Function Setup..................................................... 33

Others........................................................................... 50

Instruction Manual

Thank you for purchasing an Onkyo BLU-RAY DISC

PLAYER. Please read this manual thoroughly before

making connections and plugging in the unit.

Following the instructions in this manual will enable

you to obtain optimum performance and listening

enjoyment from your new BLU-RAY DISC PLAYER.

Please retain this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing

or climbing on it. A falling unit can cause serious injury or even death.

1. Recording Copyright—Unless it’s for personal

use only, recording copyrighted material is illegal

without the permission of the copyright holder.

• This unit’s top and rear panels may get warm

after prolonged use. This is normal.

• If you do not use this unit for a long time, it may

not work properly the next time you turn it on,

so be sure to use it occasionally.

2. AC Fuse—The AC fuse inside the unit is not user-

serviceable. If you cannot turn on the unit, contact

your Onkyo dealer.

• When you’ve finished using this unit, remove all

discs and turn off the power.

3. Care—Occasionally you should dust the unit all

over with a soft cloth. For stubborn stains, use a

soft cloth dampened with a weak solution of mild

detergent and water. Dry the unit immediately

afterwards with a clean cloth. Don’t use abrasive

cloths, thinners, alcohol, or other chemical

solvents, because they may damage the finish or

remove the panel lettering.

9. Installing this Unit

• Install this unit in a well-ventilated location.

• Ensure that there’s adequate ventilation all

around this unit, especially if it’s installed in an

audio rack. If the ventilation is inadequate, the

unit may overheat, leading to malfunction.

• Do not expose this unit to direct sunlight or heat

sources, because its internal temperature may

rise, shortening the life of the optical pickup.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST

TIME, READ THE FOLLOWING SECTION CAREFULLY.

• Avoid damp and dusty places, and places subject

to vibrations from loudspeakers.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the

voltage requirements printed on the unit’s rear

panel (AC 120 V, 60 Hz).

• Never put the unit on top of, or directly above a

loud-speaker.

• Install this unit horizontally. Never use it on its

side or on a sloping surface, because it may

cause a malfunction.

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug

is readily operable (easily accessible) at all times.

• If you install this unit near a TV, radio, or VCR, the

picture and sound quality may be affected. If this

occurs, move this unit away from the TV, radio, or

VCR.

Pressing [I/y ON / STANDBY] to select Standby

mode does not fully shutdown the unit. If you do

not intend to use the unit for an extended period,

remove the power cord from the AC outlet.

10.To Obtain a Clear Picture—This unit is a high-

tech, precision device. If the lens on the optical

pickup, or the disc drive mechanism becomes dirty

or worn, the picture quality may be affected. To

maintain the best picture quality, we recommend

regular inspection and maintenance (cleaning

or worn part replacement). Contact your Onkyo

dealer.

5. Preventing Hearing Loss

Caution

Excessive sound pressure from earphones and

headphones can cause hearing loss.

6. Batteries and Heat Exposure

Warning

11. Moisture Condensation

Batteries (battery pack or batteries installed) shall

not be exposed to excessive heat as sunshine, fire

or the like.

Moisture condensation may damage this unit.

Read the following carefully:

Moisture may condense on the lens of the optical

pickup, one of the most important parts inside this

unit.

7. Never Touch this Unit with Wet Hands—

Never handle this unit or its power cord while

your hands are wet or damp. If water or any other

liquid gets inside this unit, have it checked by your

Onkyo dealer.

• Moisture condensation can occur in the

following situations:

—

The unit is moved from a cold place to a warm

place.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you

originally bought it.

A heater is turned on, or cold air from an air

conditioner is hitting the unit.

In the summer, when this unit is moved from an

air conditioned room to a hot and humid place.

• Do not leave rubber or plastic items on this unit

for a long time, because they may leave marks

on the case.

The unit is used in a humid place.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

• Do not use this unit when there’s the possibility

of moisture condensation occurring. Doing so

may damage your discs and certain parts inside

For U.S. Models

FCC Information for User

CAUTION:

this unit.

If condensation does occur, remove all discs and

The user changes or modifications not expressly

approved by the party responsible for compliance

could void the user’s authority to operate the

equipment.

leave this unit turned on for two to three hours. By

this time, the unit will have warmed up and any

condensation will have evaporated.

12.Region Codes—The BD/DVD standard uses

region codes to control how discs can be played

around the world, the world being divided into

three regions (BD) or six regions (DVD). This unit

will only play BD/DVD discs that match its region

NOTE:

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation.

code, which can be found on its rear panel (

13.About this Manual—This manual explains how

to use all of this unit’s functions. Although the

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

BD/DVD standard offers many special features, not

all discs use them all, so depending on the disc

being played, this unit may not respond to certain

functions. See the disc’s sleeve notes for supported

features.

This unit contains a semiconductor laser system and is

classified as a“CLASS 1 LASER PRODUCT”. So, to use this

model properly, read this Instruction Manual carefully.

In case of any trouble, please contact the store where

you purchased the unit.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

To prevent being exposed to the laser beam, do not try

to open the enclosure.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

DANGER:

VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN

AND INTERLOCK FAILED OR DEFEATED. DO NOT STARE

INTO BEAM.

• Consult the dealer or an experienced radio/TV

technician for help.

CAUTION:

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES

WITH CANADIAN ICES-003.

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS

OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE

B EST CONFORME À LA NORME NMB-003 DU CANADA.

The label on the right is applied

on the rear panel.

1. This unit is a CLASS 1 LASER

PRODUCT and employs a laser inside

the cabinet.

2. To prevent the laser from being exposed, do not

remove the cover. Refer servicing to qualified

personnel.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

IR signal check

• If the remote control is not working

properly, you can use an AM radio or

digital camera (including a cellular

phone with built-in camera) to see if it

is sending out an infrared signal.

Supplied Accessories

remote control with

batteries (AAx2)

RCA audio / video cables

• With an AM radio:

Tune the AM radio station to a non-

broadcasting frequency. Point the remote

control towards it, push any button and

listen. If the sound from the radio flutters, it

is receiving the remote control’s infrared

signal.

instruction manual

quick start guide

• With a digital camera

(including built-in cell phone

cameras):

Instruction Manual

Point a digital camera towards the

remote control. Push any button on

the remote control and look through

the digital camera. If the infrared light

appears through the camera, the

remote control is working.

Note about Recycling

• This unit’s packaging materials are recyclable and

can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

• Batteries should never be thrown away or

incinerated but disposed of in accordance with your

local regulations concerning chemical wastes.

• It is forbidden by law to copy, broadcast, show,

broadcast on cable, play in public, or rent copyrighted

material without permission. Commercial BD-video/

DVD-video discs are copy-protected, and any recordings

made from these discs will be distorted. This product

incorporates copyright protection technology that is

protected by U.S. patents and other intellectual

property rights. Use of this copyright protection

technology must be authorized by Macrovision, and is

intended for home and other limited viewing uses only

unless otherwise authorized by Macrovision. Reverse

engineering or disassembly is prohibited.

Maintenance

Servicing

• Please refer to relevant topics on “TROUBLESHOOTING” on

page 50 before returning the product.

• If this unit becomes inoperative, do not try to correct the

problem by yourself. There are no user-serviceable parts

inside. Turn the unit to the standby mode, unplug the

power plug, and please contact your Onkyo dealer.

Disc handling

•

For best results, keep your discs clean. Fingerprints and dust

can affect the sound and picture quality and should be

removed as follows. Using a clean, soft cloth, wipe from the

center outwards, as shown. Never wipe in a circular direction.

• To remove stubborn dust or dirt, wipe the disc with a

damp, soft cloth, and then dry it with a dry cloth.

• Never use solvent-based cleaning fluids, such as thinner

or benzine, commercially available cleaners, or antistatic

sprays intended for vinyl records, because they may

damage the disc.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

“BD-LIVE” logo is

trademark of Blu-ray Disc

Association.

Trademark Information

HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LLC.

Manufactured under license

from Dolby Laboratories.

Dolby and the double-D

symbol are trademarks of

Dolby Laboratories.

Manufactured under license

under U.S. Patent #’s:

5,451,942; 5,956,674;

5,974,380; 5,978,762;

6,226,616; 6,487,535;

7,392,195; 7,272,567;

7,333,929; 7,212,872 & other

U.S. and worldwide patents

issued & pending. DTS is a

registered trademark and the

DTS logos, Symbol, DTS-HD

and DTS-HD Master Audio |

Essential are trademarks of

“x.v.Color” and “x.v.Color”

logo are trademarks of Sony

Corporation.

“Blu-ray Disc“ and

are trademarks.

is a trademark of DVD Format/Logo Licensing Corporation.

Java and all other Java

trademarks and logos are

trademarks or registered

trademarks of Sun

Microsystems, Inc. in the

United States and / or other

countries.

“AVCHD” and the “AVCHD”

logo are trademarks of

Panasonic Corporation and

Sony Corporation.

“BONUSVIEW” is trademark of Blu-ray Disc Association.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

Introduction

Function Setup

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

FUNCTION SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Using the Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Software Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . .8

FUNCTIONAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Front Panel Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Others

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

LANGUAGE CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Connections

CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connection to the TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connection to an Audio System . . . . . . . . . . . . . . . . . . . 16

Network Connection with LAN . . . . . . . . . . . . . . . . . . . . 18

Playback

INFORMATION ON PLAYBACK . . . . . . . . . . . . . . . . . . . 19

BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Playing Back a BD, DVD or a Disc with AVCHD Files . . . 22

Operations Using Title Menu,

Disc Menu, and Pop-up Menu . . . . . . . . . . . . . . . . . . . . . 23

Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Resume Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Playing Back an Audio CD or a Disc with MP3 Files . . 24

Reading the SD Memory Card . . . . . . . . . . . . . . . . . . . . . 25

SPECIAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Fast Forward / Fast Reverse. . . . . . . . . . . . . . . . . . . . . . . . 26

Slow Forward Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Step by Step Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

A-B Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

PIP (Picture in Picture) (BONUSVIEW) Setting . . . . . . . 27

Program Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Rapid Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Camera Angle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Enjoying BD-Live Discs with Internet. . . . . . . . . . . . . . . 29

SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

SPECIAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Switching Subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Switching Audio Soundtrack . . . . . . . . . . . . . . . . . . . . . . 31

Setting the BD Audio Mode . . . . . . . . . . . . . . . . . . . . . . . 32

Adjusting the Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

HDMI Deep Color

Features

Deep Color reduces the posterization effect of the

playback image. Refer to “HDMI Deep Color” in

“FUNCTION SETUP” on page 36.

Full high-definition video playback

Watch movies in the highest picture quality available for

your HDTV. This unit offers full high-definition video

playback up to 1080p resolution for an amazing viewing

experience. A highly detailed picture and increased

sharpness delivers a more true-to-life picture.

HDMI1080p / 24 fps output (BD only)

This unit is equipped with the feature which can provide

the smooth movement in the playback of film originated

material with the frame rate of 24 frames per second with

progressive. (Available only when the TV is connected by

an HDMI cable and compatible with 1080p24 frame input.)

Refer to “HDMI Video Resolution” in “FUNCTION SETUP”

on page 36.

Upconvert DVD for enhanced picture quality

Your current DVD will look even better than before

thanks to video upconversion. Upconversion will increase

the resolution of standard definition DVD to high

definition up to 1080p over an HDMI connection. The

picture will be less jagged and more realistic for a near

high-definition experience.

Playing back the contents in SD Memory Card

You can play back AVCHD/MP3 stored in an SD Memory Card.

You can store picture-in-picture commentary, subtitles or

other extras for BD-ROM Ver. 2 (Profile 2.0/Profile 1.1) files in

an SD Memory Card and play back with the BD-video.

Enjoy your content on different kinds of media

Full backwards compatibility with DVD, CD and SD Card

ensures that you can continue to enjoy your current audio-

video collection. Additionally, you can listen to MP3 files.

Playing back AVCHD files

This unit supports playback of AVCHD format files (new

format for high definition video camcorders) recorded on

disc/SD card. Your high definition personal archive is

playable in HD quality.

Listen to the rich multi-channel surround sound

Multi-channel surround sound, which realizes real-to-life

sound and makes you feel that you are really there.

x.v.Color

Easy and simple connection to your HDTV via HDMI

This unit supports playback of video contents on discs

recorded with “x.v.Color” technology. To watch this video

content with the “x.v.Color” space, a TV or other display

device supporting both video image reproduction using

“x.v.Color” standard and capability of manual switching of

its color space setting is required. Please refer to the

owner’s manual of your display device for further

information.

Connect this unit to your HDTV with one single HDMI

(high definition multimedia interface) cable. It is

recommended to use High Speed HDMI Cable for better

compatibility. The high definition video output signal will

be transferred to your HDTV without conversion to

analogue signals, so you will get an excellent picture and

sound quality, completely free from noise.

Thanks to other multiple outputs, you can also easily

connect to your home theater system or amplifier.

Symbols Used in this Manual

About HDMI CEC (consumer electronics control)

This unit supports HDMI CEC, which allows integrated

system control over HDMI and is part of the HDMI

standard. Onkyo does not guarantee 100% interoperability

with other brands of HDMI CEC compliant devices.

To specify for which media type each function is, we put

the following symbols at the beginning of each item to

operate.

Symbol Description

PIP (Picture in Picture) (BONUSVIEW) setting

Description refers to BD-video and

BD-RE (ver. 2.1) / BD-R (ver. 1.1/1.2/1.3)

recorded in BDMV format

Some BD-video have the PIP (picture-in-picture) function

which enables you to display the secondary video in the

primary video. You can call up the secondary video by

pressing [PIP] whenever the scene contains the

secondary video.

BD-V

DVD-V

AVCHD

Description refers to DVD-video

Description refers to DVD+RW/+R/-RW/-R

and SD Card / SDHC Card with AVCHD files

BD-Live

BD-Live (BD-ROM ver. 2 (Profile 2.0/Profile 1.1)) that allows

interactive functions to be used when this unit is connected

to the Internet in addition to be BONUSVIEW function. The

various functions differ depending on the disc.

Description refers to audio CD / DTS-CD

Description refers to BD, DVD, CD-RW/-R and

SD Memory Card with MP3 files

MP3

Pop-up menu

If you do not find any of the symbols listed above under

the function heading, the operation is applicable to all

media.

Some BD-video have pop-up menu which is a navigation

menu that can be called up and be operated on the TV

screen without interrupting the playback. You can call up

the pop-up menu by pressing [POP UP MENU / MENU].

Contents in the pop-up menu vary depending on the disc.

Rapid playback

Playback in slightly faster speed while keeping the sound

output.

Rapid playback is available only on discs recorded in the

Dolby Digital format.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTIONAL OVERVIEW

Front Panel

1 2

7 8 9* 10

The unit can also be turned on by pressing these buttons.

6. Display

• Refer to “Front Panel Display” on page 12.

/y ON / STANDBY button

• Press to turn on the unit, or to turn the unit into the

standby mode. (To completely shut down the unit,

you must unplug the AC power cord)

7. PAUSE k button

• Press to pause playback.

2. STANDBY indicator

8. STOP C button

• This indicator lights up in red when the unit is in

• Press to stop playback.

standby mode and turns off when the unit is active.

9. PLAY B button*

3. Disc tray

• Press to start or resume playback.

• Place a disc when opening the disc tray.

10. SD CARD slot

4. OPEN / CLOSE A button*

• Insert an SD Memory Card, and play back the

contents in it.

• Press to open or close the disc tray.

5. Infrared sensor window

• Receive signals from your remote control so that

you can control the unit from a distance.

Rear Panel

1. AC power cord

5. ETHERNET terminal

• Connect to a standard AC outlet to supply power to

• Use to connect a telecommunications equipment

with LAN cable.

this unit.

• Unplug this cord from the AC outlet to completely

shut down the unit.

2. AUDIO OUTPUT (DIGITAL OPTICAL / COAXIAL) jacks

• Use to connect an AV receiver / amplifier, Dolby

Digital / DTS decoder or other device with a digital

audio optical / coaxial input jack with a digital audio

optical / coaxial cable.

6. HDMI OUT jack

• Use to connect a TV with an HDMI compatible port

with an HDMI cable.

7. AUDIO OUTPUT (ANALOG L / R) jacks

• Use to connect a TV, an AV receiver / amplifier or

other device with an RCA audio cable.

Note

3. VIDEO OUTPUT (COMPONENT) jacks

• Use to connect a TV or AV receiver with component

• Do not touch the inner pins of the jacks on the rear

panel. Electrostatic discharge may cause permanent

damage to the unit.

video inputs with an RCA component video cable.

4. VIDEO OUTPUT (VIDEO) jack

• Use to connect a TV, an AV receiver or other device

with an RCA video cable.

• This unit does not have the RF modulator.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTIONAL OVERVIEW

Remote Control

11.PLAY B button*

• Press to start playback or resume playback.

12.SKIP H button

• During playback, press once to return to the

beginning of the current title, chapter, track or file.

• During playback, press twice to return to the

previous title, chapter, track or file.

15*

13.PAUSE F button

• Press to pause playback.

• When playback is in pause mode, press repeatedly

to forward the playback step by step.

14.RESOLUTION button

• Press to set the HDMI output mode.

15.OPEN/CLOSE A button*

• Press to open or close the disc tray.

16.PIP button

• Press to switch picture-in-picture feature on or off

(only applicable to BD-video which supports the

PIP function).

17.ANGLE button

• Press to access various camera angles on the disc.

18.REPEAT button

• Press to toggle between various repeat modes.

11*

19.CLEAR button

• Press to clear the information once entered, to

clear the marker settings, or to cancel the

programming for audio CD, etc.

20.A-B button

• Press to play back a defined section between point

A and B repeatedly.

21.POP UP MENU/MENU button

• Press to display the pop-up menu / disc menu.

22.ENTER button

The unit can also be turned on by pressing these

buttons.

• Press to confirm or select menu items.

23.RETURN button

1. DISPLAY button

• Press to return to the previously displayed menu

• Press to display the on-screen display menu.

screen.

2. ON/STANDBY /y button

24.AUDIO button

• Press to turn on the unit, or to turn the unit into

the standby mode. (To completely shut down the

unit, you must unplug the AC power cord)

• Press to display the audio menu.

25.FWD D button

• During playback, press to fast forward the

3. Number buttons

playback.

• Press to enter the title, chapter, track or file

• In pause mode, press to slow forward the playback.

number.

26.STOP C button

• Press to enter values in the input field.

• Press to stop playback.

4. SEARCH button

27.SKIP G button

• Press to display the search menu.

• During playback, press to skip to the next title,

5. A / B / C / D button

chapter, track or file.

• Press to select items on some BD menus.

• When file list / thumbnail list is shown, press to

switch between pages.

28.MODE button

• During BD, DVD or AVCHD files playback, press to

display the setting for the rapid playback and the

picture adjustment.

6. TOP MENU button

• Press to display the top menu.

• During BD playback, press to turn the picture-in-

picture feature on or off (only applicable to

BD-video which supports the PIP function).

• In stop mode with BD inserted, press to display a

menu for setting the BD audio mode.

• In stop mode with audio CD, or a disc with MP3

files inserted, press to display menus for program

and random playback.

7. Cursor K / L /

{

buttons

• Press to select items or settings.

8. SETUP button

• Press to display the setup menu.

9. SUBTITLE button

• Press to display the subtitle menu.

10.REV E button

• During playback, press to fast reverse the playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTIONAL OVERVIEW

Installing the Batteries in the Remote Control

Using a Remote Control

Install the batteries (AAx2) matching the polarity

indicated inside battery compartment of the remote

control.

Keep in mind the following when using the remote

control:

• Make sure that there are no obstacles between the

remote control and the infrared sensor window on the

unit.

1 Open the cover.

• Remote operation may become unreliable if strong

sunlight or fluorescent light is shining on the infrared

sensor window of the unit.

• Remote control for different devices can interfere with

each other. Avoid using remote control for other device

located close to the unit.

• Replace the batteries when you notice a fall off in the

operating range of the remote control.

• The maximum operable ranges from the unit are as

follows.

2 Insert batteries.

Infrared sensor window

Remote control sensor

DV-BD507

Make sure to match + and - on the batteries to the

marks indicated in the battery compartment.

30˚

(5 m)

30˚

3 Close the cover.

16 ft.

Approx.

Note

Incorrect use of batteries can result in hazards such as

leakage and bursting. Please observe the following:

• Do not mix new and old batteries together.

• Do not use different kinds of batteries together.

Although they may look similar, different batteries

may have different voltages.

• Make sure that the + and - ends of each battery

match the indications in the battery compartment.

• Remove batteries from battery compartment that is

not going to be used for a month or more.

• When disposing of used batteries, please comply with

governmental regulations or environmental public

instruction’s rules that apply in your country or area.

• Do not recharge, short-circuit, heat, burn or

disassemble batteries.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTIONAL OVERVIEW

Front Panel Display

• Brightness of the display can be adjusted. Refer to “Panel Display” in “FUNCTION SETUP” on page 43.

1. Displays playback status icon. Refer to the table below.

2. Displays various kinds of information such as title number, elapsed time, repeat mode, etc.

Playback status icon

Mode

Disc

SD Memory Card

Playback is in progress

Stop mode

Pause mode

Fast forward mode

Fast reverse mode

Slow forward mode

(for AVCHD only)

Appears while repeat function is set

Example of Display Message

Title is being played back.

Loading a disc.

Indicating the current title

number and the elapsed

time.

Current chapter is in

chapter repeat mode.

Dolby Digital audio is

being played back.

DTS audio is being played

back.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS

Connection to the TV

• Make one of the following connections, depending on the capabilities of your existing device.

AUDIO CONNECTION

AUDIO / VIDEO

CONNECTION

VIDEO CONNECTION

1, 2

Method 1

Method 2

Method 3

standard audio

standard picture

better picture

best audio / picture

AUDIO IN

COMPONENT

VIDEO IN

VIDEO

HDMI IN

(Green)

(Blue)

(Red)

RCA

audio cable

RCA

video

cable

HDMI

cable

RCA

component

video cable

(Green)

and

this unit

(Blue)

(Red)

AUDIO OUTPUT

(ANALOG L/R)

VIDEO OUTPUT

(VIDEO)

VIDEO OUTPUT

(COMPONENT)

HDMI OUT

This unit is compatible with the progressive scan system. The feature provides you with the higher quality pictures

than traditional output system does. To utilize this feature, a component or an HDMI connection is required. Refer

to “HDMI Video Resolution” or “Component Output” setting on page 36 to set the video resolution.

Analog audio connection is not required for this connection.

Supplied cables used in this connection are as follows:

• RCA audio cable (L/R) x 1

• RCA video cable x 1

Please purchase the rest of the necessary cables at your local store.

Note

• Connect this unit directly to the TV. If the RCA audio / video cables are connected to a VCR, pictures may be

distorted due to the copy-protection system.

• If the picture is not output properly to the TV because of “HDMI Video Resolution” or “Component Output” setting,

press and hold [PLAY B] on the front panel for more than 5 seconds. “HDMI Video Resolution” and “Component

Output” setting will be reset to the default automatically. You cannot change the video resolution during Blu-ray

Disc playback. To change the resolution, stop playback.

• A simple 1-cable connection with a device having an HDMI (high-definition multimedia interface) jack allows

digital transfer of both digital video signals and multi-channel audio signals.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS

HDMI Output Mode and Actual Output Signals

Press [RESOLUTION] to change the resolution of the video signal being output from HDMI OUT jack. The video

resolution changes as follows every time [RESOLUTION] is pressed.

Front Panel

Display

HDMI Video Resolution

480 Progressive

Press [RESOLUTION]

To play back the digital video images of a BD / DVD

720 Progressive

via an HDMI connection, it is necessary that both the

unit and the TV (or an AV receiver) support a

bandwidth digital content protection system). HDCP is

copy protection technology that comprises data

encryption and authentication of the connected AV

device. This unit supports HDCP. Please read the

operating instructions of your TV (or AV receiver) for

more information.

Press [RESOLUTION]

1080 Interlaced

Press [RESOLUTION]

1080 Progressive

Press [RESOLUTION]

1080 Progressive 2424 frame

Press [RESOLUTION]

Note

• When using HDCP-incompatible TV, the image will not be viewed properly.

• The audio signals from HDMI OUT jack (including the sampling frequency, the number of channels and bit length)

maybe limited by the device that is connected.

• Among the devices that support HDMI, some do not support audio output (e.g. projectors). In connections with

device such as this unit, audio signals are not output from HDMI OUT jack.

• Video and audio signals may be distorted temporarily when switching to / from the HDMI output mode.

• You cannot change the video resolution during Blu-ray Disc playback. To change the resolution, stop playback.

• You can also change the HDMI output mode from “HDMI Video Resolution” setting in “Video” menu. In this menu,

you can confirm what HDMI video resolutions are supported by connected TV. Refer to page 36.

• In order to get natural and high quality film reproduction of 24-frame film material, use an HDMI cable (High Speed

HDMI Cable is recommended) and select “1080p24” if the connected TV is compatible with 1080p24 frame input.

• Even if you set “HDMI Video Resolution” setting to “1080p24”, when the contents of the disc is not compatible for

1080p24 frame, 1080p60 frame will be output.

• It is recommended to use High Speed HDMI Cable (also known as HDMI category 2 cable) for better compatibility.

HDMI Audio Out Setting

When using HDMI connections make “HDMI Audio Out” setting in “Audio” menu according to the specifications of the

device to be connected. Refer to page 38.

Device to be connected

“HDMI Audio Out” setting

Output HDMI audio signal

Device compatible with Dolby Digital,

Dolby Digital Plus, Dolby TrueHD, DTS

or DTS-HD decoding

HDMI Multi (Normal)

Dolby Digital, Dolby Digital Plus, Dolby

TrueHD, DTS, or DTS-HD bitstream are

output from HDMI OUT jack. Make the

speaker settings on the connected AV

receiver, etc.

Device compatible with 3 or more

channels of audio inputs (not Dolby

Digital, Dolby Digital Plus, Dolby

TrueHD, DTS or DTS-HD compatible)

HDMI Multi (LPCM)

Multi-channel audio signals are output

from HDMI OUT jack. Make the speaker

settings with the speaker setting items

appear after you select “HDMI

Multi(LPCM)”. Refer to page 38.

Device compatible with 2-channel

audio input or device not compatible

with audio input

HDMI 2ch

Down-mixed 2-channel audio signals

are output from HDMI OUT jack.

HDMI connection to a TV and digital

audio connection (optical/coaxial) to an

AV receiver

Audio Mute

HDMI audio will be mute, and Dolby

Digital / DTS bitstream or LPCM will be

output from AUDIO OUTPUT (DIGITAL

OPTICAL / COAXIAL) jacks depending

on “Digital Out” setting. Refer to page 39.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS

■ Audio signals output from HDMI OUT jack

“HDMI Audio Out”

setting

“HDMI Multi (Normal)”

“HDMI Multi (LPCM)”

“HDMI 2ch”

“BD Audio Mode”

setting

“HD Audio “Mix Audio “HD Audio “Mix Audio “HD Audio “Mix Audio

Output” Output” Output” Output” Output” Output”

Media

Audio Source

Which audio format can be output depends on the compatibility of the connected

device.

Downmix

2ch PCM

Downmix

2ch PCM

Dolby Digital

Dolby Digital Dolby Digital Multi PCM

Dolby Digital

Multi PCM

Downmix

Dolby Digital Plus

Dolby Digital Multi PCM*¹Multi PCM*²

Dolby Digital Multi PCM*³Multi PCM*⁴

2ch PCM

2ch PCM*

Plus

Dolby

TrueHD

Downmix

Dolby TrueHD

DTS

2ch PCM

2ch PCM*

BD-video

AVCHD

Downmix

2ch PCM

Downmix

2ch PCM

DTS

Multi PCM*⁷Multi PCM*⁷

Multi PCM*^{5, 7}Multi PCM*^{6, 7}

Downmix

DTS-HD

LPCM

DTS-HD

Multi PCM

2ch PCM

2ch PCM*

Downmix

2ch PCM

Downmix

2ch PCM

Multi PCM

Dolby Digital

LPCM

Dolby Digital

DTS

Dolby Digital

Multi PCM

Downmix 2ch PCM

Multi PCM

Dolby Digital

DTS

Multi PCM

2ch PCM

Downmix 2ch PCM

2ch PCM

DVD-

video

LPCM

2ch PCM

Audio CD

/ MP3

DTS-CD

PCM

DTS

2ch PCM

DTS

2ch PCM

Multi PCM

Downmix 2ch PCM

Full decoded.

Only the independent substream is decoded.

Dolby TrueHD stream is decoded.

Only the Dolby Digital substream is decoded.

Full decoded.

Only the core substream is decoded.

When audio source is Multi-channel, decorded as 7.1ch. However, number of the output audio channel will depend

on the number of the connected speakers.

• If the connected device is not compatible with the HDMI BITSTREAM, audio will be output as multi LPCM or 2-channel

down-mixed LPCM depending on the capability of the connected device even if you select “HDMI Multi(Normal)” in

“HDMI Audio Out” setting. Refer to page 38.

• When playing back a BD-video which only contains the primary audio, the audio output will be the same case as the

“HD Audio Output” even if the “BD Audio Mode” is set to “Mix Audio Output”.

Note

• The audio signals from HDMI OUT jack (including the sampling frequency, the number of channels and bit length)

maybe limited by the device that is connected.

• Among the devices that support HDMI, some do not support audio output (e.g. projectors). In connections with

device such as this unit, audio signals are not output from HDMI OUT jack.

• Video and audio signals may be distorted temporarily when switching to / from the HDMI output mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS

Connection to an Audio System

• When you change the connections, all devices should be turned off.

• Refer to the manual accompanying external devices for more information.

2-Channel Analog Audio Connection

stereo system

AUDIO IN

audio

analog audio input jacks

RCA audio cable

this unit

AUDIO OUTPUT (ANALOG L/R)

Digital Audio Connection

audio

AV receiver / amplifier

DIGITAL AUDIO INPUT

OPTICAL

DIGITAL AUDIO INPUT

COAXIAL

digital audio

coaxial input jack

digital audio

optical input jack

digital audio

optical cable

digital audio

coaxial cable

this unit

AUDIO OUTPUT (DIGITAL OPTICAL/COAXIAL)

Supplied cables used in this connection are as follows:

• RCA audio cable (L/R) x 1

Please purchase the rest of the necessary cables at your local store.

Note for Digital Audio Optical Cable

• Digital audio optical cable may be damaged when bent at sharp angles. Endure cables are coiled in loops with a

diameter of 6 inches (15cm) or more when storing them.

• Use a cable which is 9.8 feet (3m) or shorter.

• Insert cable plugs firmly into the connectors when making connections.

• If a plug has dust or is dirty, clean it with a soft cloth before inserting it into a connector.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS

■ Audio signals output from AUDIO OUTPUT (DIGITAL OPTICAL / COAXIAL) jacks

For the settings in the “Digital Out” to take effect, “HDMI Audio Out” should be set to “Audio Mute”. Otherwise, the

settings made in the “HDMI Audio Out” will have a priority, and the same signal as being output from the HDMI OUT

jack will be output from the AUDIO OUTPUT (DIGITAL OPTICAL / COAXIAL) jacks as well. (Except that Dolby Digital will

be output instead of Dolby Digital Plus and Dolby TrueHD, and DTS signal will be output instead of DTS-HD.)

“Digital Out” setting

“Bitstream”

“LPCM”

“BD Audio Mode”

setting

“HD Audio

Output”

“Mix Audio

Output”

“HD Audio Output” “Mix Audio Output”

Media

Audio Source

Which audio format can be output depends on the compatibility of the connected

device.

Dolby Digital

Dolby Digital Plus

Dolby TrueHD

DTS

DTS-HD

LPCM

Dolby Digital

LPCM

Dolby Digital

DTS

Dolby Digital

DTS

Dolby Digital

DTS

Downmix 2ch PCM

BD-video

AVCHD

Downmix 2ch PCM

DTS

Downmix 2ch PCM Downmix 2ch PCM Downmix 2ch PCM

Dolby Digital

Downmix 2ch PCM

Dolby Digital

DTS

Downmix 2ch PCM

2ch PCM

DVD-

video

LPCM

2ch PCM

Audio CD

/ MP3

DTS-CD

PCM

DTS

2ch PCM

DTS

2ch PCM

Downmix 2ch PCM

Full decoded.

Only the independent substream is decoded.

Dolby TrueHD stream is decoded.

Only the Dolby Digital substream is decoded.

Full decoded.

Only the core substream is decoded.

• When playing back a BD-video which only contains the primary audio, the audio output will be the same case as the

“HD Audio Output” even if the “BD Audio Mode” is set to “Mix Audio Output”.

Note

• In order to output LPCM signal from AUDIO OUTPUT (DIGITAL OPTICAL / COAXIAL) jacks while outputting the

HDMI audio signal, set “HDMI Audio Out” setting to “HDMI Multi(LPCM)”.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS

Network Connection with LAN

• You can use a disc which offers BD-Live function by connecting the unit to the Internet.

(For BD-Live information, please refer to page 29)

Telecommunications

equipment (modem, etc.)

Hub or broadband router

WAN

LAN

LAN cable

Internet

this unit

No supplied cables are used in this connection:

Please purchase the necessary cables at your local store.

Note

• After connecting to the Internet, set up necessary network settings.

• Do not insert any cable other than a LAN cable to the ETHERNET terminal to avoid damaging the unit.

• If your telecommunications equipment (modem, etc.) does not have broadband router functions, connect a

broadband router.

• If your telecommunications equipment (modem, etc.) has broadband router functions but there is no vacant port,

use a hub.

• For a broadband router, use a router which supports 10BASE-T/100BASE-TX.

• Do not connect your PC directly to the ETHERNET terminal of this unit.

• For the network setup, refer to “Network Connection” on pages 45-48.

Download from Www.Somanuals.com. All Manuals Search And Download.

INFORMATION ON PLAYBACK

Before you start playing back a disc, read the following information.

Readable cards

Playable files / data

Playable Discs and Files

SD Memory Card (8MB - 2GB)

This unit is compatible to play back the following discs / files.

To play back a disc / file, make sure that it meets the

requirements for region codes and color systems as described

below. You can play back discs that have the following logos.

Other disc types are not guaranteed to play back.

AVCHD, MP3, picture-in-

picture commentary,

subtitles or other extras

for BD-ROM ver. 2 (Profile

2.0/Profile 1.1)

SDHC Memory Card (4GB - 8GB)

miniSD Card (8MB - 2GB)

microSD Card (8MB - 2GB)

Playable discs

Blu-ray Disc

- BD-video

(single / double layer)

- BD-RE* (ver. 2.1)

(single / double layer)

(Recorded in BDMV format)

- BD-R (ver. 1.1/1.2/1.3)

(single / double layer)

(Recorded in BDMV format)

(Unclosed discs may not be

played back.)

Logos

Note for SD Memory Cards

• Do not remove the SD Memory Card or turn the unit

to the standby mode while the contents of the card

is in playback. It may result in malfunction or loss of

the card’s data.

• Please keep the SD Memory Cards in their cases

when you are not using them.

• Do not try to open or modify the card.

• Do not touch the terminal surface with your fingers

or any metals.

• Do not attach additional labels or stickers to cards.

• Do not remove the label of the SD Memory Cards.

• This unit supports SD Memory Card with FAT12/

FAT16 file system, and SDHC Memory Card with

FAT32 file system.

• This unit may not read the SD Memory Cards

formatted on computer. If that is the case, please

reformat the SD Memory Cards in this unit and try

again.

DVD-video

DVD+RW (single layer)

DVD+R (single / double layer)

(finalized discs only)

• This unit does not support miniSDHC and microSDHC

Memory Card.

DVD-RW (single layer)

(finalized video mode discs

only)

DVD-R (single / double layer)

(finalized video mode discs

only)

• For miniSD Card and microSD Card, the adapter is

necessary.

miniSD Card

microSD Card

adapter

miniSD Card

microSD Card

• Portions of this product are protected under

ARIS / SOLANA / 4C.

CD-DA (audio CD)

CD-RW

Unplayable Discs and Files

CD-R

The following discs will not be played back in this unit.

• CD-ROM

• CD-I (compact disc-interactive)

• VSD (video single disc)

• video CD

• DVD-RAM

• DVD-audio

• HD DVD

DTS-CD

* Due to the intentional progression of the Blu-ray Disc format

by its standard setting authority, the company cannot

guarantee or warrant the playability of future extensions of the

Blu-ray Disc format with this product.

• SVCD

• unfinalized disc

• BD / DVD / CD / SD Memory Card contains DivX®,

Windows Media™ Audio and JPEG files.

Playable files

Media

• Multi-session born BD-RE/-R with MP3 files.

DVD, SD Memory Card

(including SDHC), miniSD

Card, microSD

• super audio CD - Only the sound on the CD layer can

be heard. The sound on the high-density super audio

CD layer cannot be heard.

• Playability of dual discs are not guaranteed.

• BD-RE / -R recorded in BDAV format or non compatible

recording format.

AVCHD

BD, DVD, CD-RW/-R,

SD Memory Card

(including SDHC), miniSD

Card, microSD Card

MP3

Download from Www.Somanuals.com. All Manuals Search And Download.

INFORMATION ON PLAYBACK

On-Screen Display

Color Systems

You can check information about the current disc by

BD-video and DVD-video are recorded in different color

systems throughout the world. The most common color

system is NTSC (which is used primarily in the United

States and Canada).

This unit employs NTSC color system, so the disc you play

back must be recorded in the NTSC system. You cannot

play back the disc recorded in other color systems.

pressing [DISPLAY].

To call the on-screen display menu, press [DISPLAY]

during playback. Every time you press [DISPLAY], the

information changes. Depending on the media, available

information varies.

BD-V

AVCHD

Region Codes

off A Title / Chapter information

A Title information (elapsed time)

A Title information (remaining time)

A HDMI information A off

BD-video

This unit has been designed to play back

BD-video with region “A” and DVD-video with

region “1” or “ALL“. You cannot play back

BD-video or DVD-video that are labeled for

other regions. Look for the symbols on the

right on your BD-video or DVD-video.

If these region symbols do not appear on

your BD-video or DVD-video, you cannot

play back the disc in this unit. The letter or

number inside the globe refers to region of

the world. A BD-video or DVD-video labeled

for a specific region can only be played back

in the unit with the same region code.

DVD-V

off A Chapter information (elapsed time)

A Chapter information (remaining time)

A Title information (elapsed time)

A Title information (remaining time)

A Bit rate information A HDMI information A off

DVD-video

off (Track information (elapsed time))

A Track information (remaining time)

A Disc information* (elapsed time)

A Disc information* (remaining time)

A off (Track information (elapsed time))

(*not available during the program/random playback)

Structure of Disc / SD Memory Card Contents

The contents of BD/DVD are generally divided into titles.

Titles may be further subdivided into chapters.

BD / DVD / AVCHD

MP3

title 2

title 1

chapter 1 chapter 2 chapter 1 chapter 2 chapter 3

off (File information (elapsed time))

A File name information

A off (File information (elapsed time))

Audio CDs are divided into tracks.

audio CD

track 3

track 1

track 2

track 4

track 5

Data discs or SD Memory Cards containing MP3 are

divided into folders, and the folders are subdivided into

files.

MP3

folder (group) 1

group(folder)1

folder (group) 2

group(folder)2

ﬁle (track) 1 ﬁle (track) 2 ﬁle (track) 3 ﬁle (track) 4 ﬁle (track) 5

Download from Www.Somanuals.com. All Manuals Search And Download.

INFORMATION ON PLAYBACK

■ Chapter information

■ HDMI information

Video Info

Audio Info

Max Channel :

YCbCr/

PCM

2 ch

1080i

1 / 10

HDMI video format

Resolution of the HDMI output image

HDMI audio format

Maximum numbers of audio channels that can be

accepted by the connected device

3 / 5

0 : 01 : 02

CHAPTER

Current title number

Current chapter number / Total number of

chapters

Note

Current repeat setting (Only when repeat setting

is active)

• If the HDMI cable is not connected, “---” will be

displayed for HDMI information.

(C: Chapter repeat, T: Title repeat, AB : A-B repeat)

Indicates that the multi camera angle images are

available on the scene

Current playback status

Elapsed time / Remaining time of the current

chapter

■ Track / File information

■ Title information

1 / 14

0 : 00: 51

Current track (file) number / Total number of track

(file)

Elapsed time of the current track and file /

Remaining time of the current track

Indication of SD Memory Card playback

Current repeat setting

3 / 5

0 : 01 : 02 SD

Current title number / Total number of titles

Elapsed time / Remaining time of the current title

Indication of SD Memory Card playback

(Only when repeat setting is active)

(T: Track / File repeat, G: Group repeat,

A: All repeat, AB: A-B repeat)

■ Bit rate information

■ Disc information

Bit rate (The amount of video data currently being

read)

Layer number

(L0: Layer 0 is played back. L1: Layer 1 is played

back)

1 / 14

0 : 00: 51

Current track number / Total number of tracks

Elapsed time / Remaining time of the current disc

■ File name information

File_name_001

Media icon and file name

: MP3 file

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC PLAYBACK

Playing Back a BD, DVD or a Disc with AVCHD Files

BD-V

DVD-V

AVCHD

Press [ON /STANDBY /y].

Turn on the TV and select the

appropriate input on the TV to which

the unit is connected.

Press [OPEN / CLOSE A ] to open the

disc tray.

Place the disc on the disc tray with its

label side facing up.

Align the disc to the

disc tray guide.

Press [OPEN / CLOSE A ] to close the

disc tray.

It may take a while to load the disc.

Some discs may start playback automatically.

Press [PLAY B] to start playback.

For many of BD-video and DVD-video, a menu

screen may appear.

In this case, use [K / L /

B] to select the

desired item, then press [ENTER].

Press [STOP C ] once to stop

playback temporarily.

Refer to “Resume Playback” on page 23.

To eject the disc:

Press [OPEN / CLOSE A ] to open the disc tray,

then remove the disc before turning off the unit.

Note

•

may appear at the top-right on the TV screen

when the operation is prohibited by the disc or this

unit.

• During the playback of 2-layered disc, pictures may

stop for a moment. This happens when the 1st layer

switches to the 2nd layer. This is not a malfunction.

• BD/DVD/AVCHD/menu varies depending on discs.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC PLAYBACK

Operations Using Title Menu,

Disc Menu, and Pop-up Menu

Pause

1 During playback, press [PAUSE F ].

BD-V

DVD-V

AVCHD

• Playback will be paused.

Many of BD-video and DVD-video disc contains title menu

(BD-video / DVD-video / AVCHD), disc menu (DVD-video)

or pop-up menu (BD-video) which guides you through

the available functions in the disc. The contents of the

menus may differ depending on the discs.

2 Press [PLAY B ] to return to normal

playback.

Title menu (BD-video / DVD-video / AVCHD)

1 Press [TOP MENU].

• The title menu will appear.

Note

• For BD and DVD, set “Still Mode” setting to “Field” in

“Video” menu if pictures in the pause mode are

blurred (refer to page 37).

2 Use [K / L /

B] to select an item, then

press [ENTER].

3 Press [TOP MENU] to exit.

Disc menu (DVD-video)

Resume Playback

1 Press [POP UP MENU / MENU].

1 During playback, press [STOP C ].

• The disc menu will appear.

• Resume message will appear on the TV screen.

2 Use [K / L /

B] to select an item, then

press [ENTER].

Resume ON

3 Press [POP UP MENU / MENU] to exit.

Press ‘PLAY’ to play from here.

To play from the beginning,

press ‘STOP’ first and then ‘PLAY’.

Pop-up menu (BD-video)

• This is a special feature available for some BD-video.

When you press [POP UP MENU / MENU], a menu pops

out on the TV screen while the contents still play back.

e.g.) BD

1 During the playback of BD-video, press

[POP UP MENU / MENU].

2 Press [PLAY B ].

• In a few seconds, playback will resume from the

point at which it stopped last. To cancel the resume

playback and start playback the disc from the

beginning, press [STOP C ] again in stop mode.

• For MP3, playback will resume from the beginning

of the current file.

• The pop-up menu will appear.

2 Use [K / L /

B] to select an item, then

press [ENTER].

3 Press [POP UP MENU / MENU] to exit.

Note

• Resume playback may not be available for the BD

• Contents of menus and corresponding menu

operations may vary among discs. Refer to the

manual accompanying the disc for details.

that supports Java applications (BD-Java).

• In the “Disc” mode, the resume information will be

cleared when;

- [STOP C] is pressed while in stop mode.

- the parental level is changed.

- the disc tray is opened.

• In the “SD Card” mode, the resume information will

be cleared when;

- [STOP C] is pressed while in stop mode.

- the SD Memory Card is removed.

- the unit is turned into the standby mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC PLAYBACK

It is recommended that MP3 files to be played back in

Playing Back an Audio CD or a Disc

with MP3 Files

this unit are recorded under the following

specifications:

• Sampling frequency: 32 kHz, 44.1 kHz or 48 kHz

MP3

• Constant bit rate:

112 kbps - 320 kbps

Insert an audio CD or a disc with MP3

files.

Note

• The file list will appear on the TV screen.

• The system can recognize up to 255 folders / 999 files

for CD, 999 folders / 9999 files for BD, DVD and SD

Memory Card (including the files other than MP3).

When number of folder / files exceeds the limit, they

will be recognized by the order recorded.

• The name of folder and file can be displayed up to 28

characters. Unrecognizable characters will be

replaced with asterisks.

• The 9th and deeper hierarchies cannot be displayed

for CD and the 10th and deeper hierarchies cannot

be displayed for BD, DVD and SD Memory Card.

• Files whose extension is other than “.mp3 / .MP3” will

not be listed.

To return to the first item:

• Press [TOP MENU].

To return to the track/file played last:

• Press [POP UP MENU / MENU].

Use [K / L] to select a desired folder

or file, then press [ENTER].

Use [

] to go back and forward

between the hierarchies.

• If you press [ENTER] on the desired file,

playback will start.

• Some unplayable folders or files may be listed due to

the recording status.

• This unit recognizes up to 8 characters of file name in

the SD Memory Card. Characters after 8th will not be

displayed.

• For the SD Memory Card playback, refer to “Reading

the SD Memory Card” on page 25.

- - / 20

File List

MP3_DISC

Folder_1

Folder_2

Folder_3

MP3_A

• If a disc contains AVCHD files, the playback of other

files which are in the same disc is not available.

MP3_B

MP3_C

MP3_D

Page Up

Page Down

e.g.) MP3

Track / File information

audio CD: “CD-DA” will be displayed.

MP3:

Current folder name (Disc or SD

Memory Card name will be displayed

for the top of the hierarchies.)

audio CD: List of the track number and time

MP3:

List of the file / folder names in the

current folder / disc)

Operation Press [A] to go to the previous page.

guide: Press [B] to go to the next page.

Current page / Total page number

Playback status

Icons:

: Folder

: audio CD track

: MP3 file

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC PLAYBACK

Inserting the SD Memory Card and Playback

Reading the SD Memory Card

Insert an SD Memory Card, with the

label side facing up, into the SD

CARD slot until it clicks.

If no disc is in operation, “Media Select” screen

will appear on the TV screen.

AVCHD

MP3

You can play back the AVCHD/MP3 files in an SD Memory

Card. With the SD Memory Card, you can also enjoy the

special additional contents for BD-ROM ver. 2 (Profile 2.0/

Profile 1.1) which can be downloaded from the Internet.

You can store the contents on an SD Memory Card via

computer and play them back with the BD-video. For more

information about the special additional contents, please

refer to the instruction book that came with the disc.

SD Memory Card

Use [K / L] to select "SD Card", then

press [ENTER].

The file list will appear.

■ Setting the media mode

In stop mode, press [SETUP].

Follow the step 2 in “Playing Back an

Audio CD or a Disc with MP3 Files”

on page 24.

Use [ K / L ] to select , then press

[ENTER].

Quick

Removing the SD Memory Card

In stop mode, push the SD Memory

Card and then slowly remove your

finger.

Media Select

Disc

HDMI Audio Out

HDMI Video Resolution

Component Output

Player Menu

HDMI Multi (Normal)

Auto

480i

English

Grasp the card and pull it out from

the SD CARD slot.

This will set the unit to “Disc” mode.

Use [ K / L ] to select “Media Select”

Compatible Cards:

- SD Memory Card (8MB - 2GB)

- SDHC Memory Card (4GB - 8GB)

- miniSD Card (8MB - 2GB)

- microSD Card (8MB - 2GB)

• For miniSD Card and microSD Card, the adapter will

be required.

setting.

Press [ENTER] repeatedly to select

“SD Card”.

Quick

Note

Media Select

SD Card

HDMI Multi (Normal)

Auto

• The “Media Select” screen will disappear under the

HDMI Audio Out

HDMI Video Resolution

Component Output

Player Menu

conditions listed below:

- when [RETURN] is pressed.

- when the setup menu is called up.

480i

English

• Do not remove the card during its playback.

• This unit supports SD Memory Card with FAT12 /

FAT16 file system, and SDHC Memory Card with

FAT32 file system.

• Do not delete the folders or files in the SD Memory

Card with your computer. This unit might not read

the SD Memory Card.

• This will set the unit to “SD Card” mode. To

play back the contents in any discs, exit “SD

Card” mode by selecting “Disc”.

• This unit recognizes up to 8 characters (including

“~1”) of file name in the SD Memory Card. Characters

after 8th will not be displayed.

Press [SETUP] to exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK

Fast Forward / Fast Reverse

Step by Step Playback

BD-V

DVD-V

AVCHD

MP3

BD-V

DVD-V

AVCHD

1 During playback, press [FWD D]

1 In pause mode, press [PAUSE F]

repeatedly for fast forward.

repeatedly.

During playback, press [REV E] repeatedly for fast

reverse.

Every time you press [FWD D] or [REV E], the

playback speed will change.

Every time you press [PAUSE F], playback will

advance one step at a time.

2 Press [PLAY B] to return to normal

playback.

2 Press [PLAY B] to return to normal

playback.

Note

• Only step by step forward is available.

Note

• Set “Still Mode” setting to “Field” in “Video” menu if

pictures in step by step playback mode are blurred

(refer to page 37).

• For BD, DVD and AVCHD, speed changes in 5 different

levels.

• For audio CD and MP3, speed changes in 3 different

levels.

• For audio CD, fast forward / fast reverse search

between different tracks are not available during

program and random playback.

• For MP3, fast forward / fast reverse search between

different files are not available.

Repeat Playback

Available repeat function may vary depending on the

discs.

1 During playback, press [REPEAT]

repeatedly to select the desired repeat

mode.

Slow Forward Playback

Repeat mode

Chapter repeat

Available media

BD-V

DVD-V

AVCHD

BD-V

DVD-V

The current chapter will be played

back repeatedly.

1 During playback, press [PAUSE F], then

AVCHD

press [FWD D].

Title repeat

BD-V

DVD-V

Every time you press [FWD D], playback speed will

change.

The current title will be played back

repeatedly.

AVCHD

2 Press [PLAY B] to return to normal

playback.

Track repeat

MP3

The current track or file will be

played back repeatedly.

Group repeat

The current folder will be played

back repeatedly.

All repeat

Note

• Slow forward speed changes in 3 different levels.

• Only slow forward is available.

• Set “Still Mode” setting to “Field” in “Video” menu if

pictures in the slow forward playback mode are

blurred (refer to page 37).

All tracks in the media will be

played back repeatedly.

Note

• The repeat setting will be canceled when you stop

playback.

• The chapter, title, track or group repeat will be

cleared when moving to other chapter, title, track /

file or folder.

• Repeat playback does not function during A-B repeat

playback.

• Chapter and title repeat are not available with some

scenes.

• When the repeat setting is set for an MP3 folder, the

repeat setting will be cancelled if you select other

MP3 folder to playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK

A-B Repeat

Program Playback

BD-V

DVD-V

AVCHD

MP3

You can play back the specific part (between point A and

point B) repeatedly.

You can play back the disc in your desired order.

1 In stop mode, press [MODE].

1 During playback, press [A-B] at the

• The program screen will appear.

desired starting point A.

2 Use [K / L] to select a track / file, then

2 During playback, press [A-B] at the

press [ENTER].

desired ending point B.

As soon as you set the point B, the part between point

A and point B will start playback repeatedly.

• To cancel the A-B repeat, press [A-B] again.

- - / 16

Program

CD_DA

Total

0 : 26 : 24

0:36

1:14

Note

1:14

0:45

0:50

0:53

0:20

0:54

0:50

1:14

0:50

0:53

0:54

0:36

• Point B should be set within the same title or track as

point A.

• A-B repeat is not available with some scenes.

• To cancel the A point which was set, press [CLEAR].

• A-B repeat does not function during chapter, title,

track, group or all repeat playback.

Page Up

Page Down

Page Prev

Page Next

e.g.) audio CD

Track / File information

PIP (Picture in Picture) (BONUSVIEW) Setting

audio CD:

MP3:

“CD-DA” will be displayed.

Current disc, SD Memory Card, or

folder name will be displayed.

BD-V

Some BD-video have the PIP (picture-in-picture) function

which enables you to display the secondary video in the

primary video. You can call up the secondary video by

pressing [PIP] whenever the scene contains the

secondary video.

Track / File list:

Track / File list in the original

order

Programmed list: Track / File list in the

programmed order

Cumulative playback time of all tracks in the

programmed list

Playback status

Current page / Total page number

Operation Guide: Press [A] to go to the previous

primary

video

page in the track / file list.

Press [B] to go to the next page

in the track / file list.

Press [C] to go to the previous

page in the programmed list.

Press [D] to go to the next page

in the programmed list.

secondary

video

1 During playback, press [PIP].

• For MP3 files, use [K / L] to select a folder, then

press [ENTER] first, and then use [K / L] to select a

file, then press [ENTER].

• Press [CLEAR] to erase the last file of the program.

• Use [K / L] to select “All Clear” at the bottom of the

list to erase all the tracks / files in the program.

• The programmed tracks / files is displayed in the

right hand screen.

PIP information will appear.

2 Use [K / L] to select the secondary video

you want.

• The secondary video will be displayed and the

secondary audio will be output.

3 Press [RETURN] or [PIP] to remove the PIP

• Use [s

B] to go back forward between the

information.

hierarchy of folders.

Note

• The secondary audio will not be output when the

secondary audio is set to “Off” or when “BD Audio

Mode” is set to “HD Audio Output”. Refer to

“Switching Audio Soundtrack” on page 31 and “Setting

the BD Audio Mode” on page 32.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK

3 Press [PLAY B ] to start program

Random Playback

playback.

• Program playback will start.

MP3

To exit from the program playback mode:

This function shuffles the playback order of tracks / files.

• Press [RETURN] in stop mode.

1 In stop mode, press [MODE] twice.

• The random screen will appear.

Note

• During program playback, press [STOP C ] once to

set the resume point, and then press [PLAY B ] to

resume program playback from where [STOP C ]

was pressed (audio CD) or from beginning of the file

where [STOP C ] was pressed (MP3).

- - / 16

Random

CD_DA

Total

1 : 13 : 29

• During program playback, press [STOP C ]. To go

back to the normal program playback, press

[RETURN] to exit from the program screen, then

press [PLAY B ].

• The program will be cleared when;

- the unit is turned into the standby mode.

- the media mode is switched to the other mode.

0:36

1:14

0:45

0:50

0:53

0:20

0:54

- the disc / card is removed. (as for “Disc” mode, just

opening the disc tray will clear the program info.)

Page Down

e.g.) audio CD

Track / File information

• Up to 99 tracks / files can be entered.

• To repeat the current track / file in the program,

press [REPEAT] repeatedly until “

appears during playback. To repeat the entire

program, press [REPEAT] repeatedly until “

appears during playback.

• Playback from a desired track / file and random

playback are not available during program playback.

Track”

audio CD:

MP3:

“CD-DA” will be displayed.

Current disc, SD Memory Card, or

folder name will be displayed.

All”

Track / File list:

Track / File list in the original

order

Operation guide: Press [A] to go to the previous

• Press [MODE] to switch to the random playback

mode.

page in the track / file list.

Press [B] to go to the next page

in the track / file list.

Total playback time of all tracks

Playback status

2 Press [PLAY B ] to start random playback.

To exit from the random playback mode:

• Press [MODE] in stop mode.

Note

• During the random playback, press [STOP C ] once

to set the resume point, and then press [PLAY B ] to

resume random playback from where [STOP C ] was

pressed (audio CD) or from beginning of the file

where [STOP C ] was pressed (MP3).

• During random playback, press [STOP C ]. To cancel

the random playback, press [MODE] when the

random playback screen is displayed.

• Up to 99 tracks / files can be entered.

• To repeat the current track / file in the random

selection, press [REPEAT] repeatedly until “

Track” appears during playback. To repeat the entire

random selection press [REPEAT] repeatedly until

“

All” appears during playback.

• You cannot go back to the previous track / file during

random playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK

Rapid Playback

Enjoying BD-Live Discs with Internet

BD-V

DVD-V

AVCHD

BD-V

You can enjoy the BD-Live functions which enable you use

the interactive functions when the unit is connected the

Internet. (For the Network connection, refer to pages 45-48.)

Examples for BD-Live interactive functions :

• Download the additional contents such as the movie’s

trailer, subtitles and BD-J, etc.

This function plays back approximately at 1.3 times the

normal playback while keeping the sound output. This

function is available only on discs recorded in the Dolby

Digital format.

1 During playback, press [MODE]

repeatedly until the Rapid playback

setting appears.

•

While downloading, special video data may be played back.

Service and functions differ depending on the disc.

Follow the instructions given by the disc when using

the BD-Live function.

Off

Press [ENTER] or [s B] to switch (x1.3), or

Note

off.

• You must connect the unit to the Internet and set up

“Off”: Plays back in normal speed.

necessary settings in order to use the BD-Live function.

• For certain discs, setting for “BD-Live Setting” may

need to be changed.

“

”: Plays back approximately at 1.3 times of

normal playback.

• Depending on your connection environment, it may

take time to connect to the Internet or the Internet

may not be connected.

• When BD-Live functions are used and the unit is

connected to the Internet, you may be charged for

this communication.

• You must insert an SD memory card when using the

BD-Live function. (SD memory card of 1GB is

recommended.)

Press [

] to return to normal playback.

Note

• Picture adjustment and audio language setting

cannot be changed during this function.

• This function may not work at some points on a disc.

• During this function, 2ch LPCM will be output from

HDMI OUT jack and AUDIO OUTPUT (DIGITAL

OPTICAL / COAXIAL) jacks.

• Do not remove the SD memory Card when using the

BD-Live function.

Note for AACS Online

• The player or disc IDs may be sent to the content

provider when playing back a disc with BD-Live

function.

Camera Angle

BD-V

DVD-V

• If you save your viewing history on the server by

using these IDs, you will be introduced to other

similar movies.

• You can save game score histories.

Some BD-video and DVD-video contain scenes which have

been shot simultaneously from various angles. You can

change the camera angle when

appears on the TV screen.

1 During playback, press [ANGLE].

• The selected angle will be displayed on the display

bar at the top of the TV screen.

2 Use [K / L] to select your desired angle.

1 / 3

Note

• If “Angle Icon” setting is “Off” in “Others” menu,

will not appear. Refer to page 43.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using [SKIP H / G ]

Using [the Number buttons] (Direct Search)

1 During playback, press [SKIP G] to

Title Search

move to the next track. Press it

In stop mode, enter the title number you

want to search using [the Number buttons].

• Playback of the title will start in a few seconds.

repeatedly to skip to subsequent tracks.

Press [SKIP H ] once to go back to the

beginning of the current track. Press it

repeatedly to go to the previous tracks.

Chapter Search

1 During playback of a title, enter the

chapter number you want to search

using [the Number buttons].

Note

• For BD and DVD, if title contains no chapters,

[SKIP H / G ] changes the title.

• Playback of the chapter will start in a few seconds.

Note

Using [SEARCH]

• As for the BD-video, how it performs will be strongly

determined by the disc, and may not perform as

described here.

By using [SEARCH], you can select following search

modes.

Search mode

Available media

BD-V

DVD-V

AVCHD

Chapter / Title search

Marker search

MP3

This feature allows you to assign a specific point on a title

or track to be called back later.

Track search

Time search

Marker search

BD-V

DVD-V

AVCHD

1 During playback, press [SEARCH]

repeatedly until the marker setting

menu appears.

BD-V

DVD-V

2 Use [s

B] to select a marker number

(1-9).

1 During playback, press [SEARCH]

repeatedly until your desired search

mode appears.

___ __ : __ :__

3 When the disc reaches the point at which

2 Enter the desired chapter, title, track, file

you want to set a marker, press [ENTER].

number or time to search for using

• The title or track and elapsed playback time will

appear on the TV screen.

[the Number buttons].

• Chapter, title, track or time search will start.

• Press [CLEAR] to erase an incorrect input.

4 Press [SEARCH] or [RETURN] to exit.

5 To return to the marker later, call the

marker setting by pressing [SEARCH]

repeatedly during playback or in stop

Note

• During program and random playback, search

functions are not available except the search using

[SKIP H / G ].

mode, and use [^s

marker, then press [ENTER].

B] to select a desired

•

Time search is available only in the same track, file or title.

• For BD/AVCHD, chapter and time search are available

only during playback.

Note

• Opening the disc tray, changing to the standby

mode or selecting “ ” at step 2 and pressing

[ENTER] will erase all markers.

• To clear a marker, use [s B] to select the marker

number to be cleared and press [CLEAR].

• You can mark up to 9 points.

•

For BD/AVCHD, marker search between different titles

is not available.

• For BD/AVCHD, you can return to the maker only

during playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL SETTINGS

You can select the format of audio and video as you prefer depending on the contents of the disc you are playing back.

Switching Subtitles

Switching Audio Soundtrack

Some BD and DVD may have subtitles in 1 or more

languages. For commercially available discs, the

supported languages can be found on the disc case.

Follow the steps below to switch the subtitle languages

during playback.

Some BD and DVD contain multiple audio streams. Those

are often in different audio languages or audio formats.

For BD, available audio varies depending on “BD Audio

Mode” setting. Refer to page 38 for more information.

BD-V

1 During playback, press [AUDIO] repeatedly

1 During playback, press [SUBTITLE]

repeatedly to display “Primary Subtitle”,

“Secondary Subtitle” or “Subtitle Style”.

to display “Primary” or “Secondary”.

“Primary”:

Sets the audio for the primary video.

“Secondary”: Sets the audio for the secondary video.

“Primary Subtitle”: Sets the subtitle for the

2 Use [K / L] to select your desired audio

primary video.

stream channel.

”Secondary Subtitle”: Sets the subtitle for the

secondary video.

Primary

JPN Dolby D

Multi-ch / 2

“Subtitle Style”:

Sets style of the subtitle.

• For “Secondary”, use [{

B] to switch between

2 Use [K / L] to select your desired subtitle

current audio setting and “Off”.

or style.

3 Press [AUDIO] repeatedly to exit.

Primary Subtitle

JPN / 4

DVD-V

AVCHD

• Use [{

B] to switch between current subtitle

1 During playback, press [AUDIO].

setting and “Off”.

2 Use [K / L] to select your desired audio

3 Press [SUBTITLE] repeatedly to exit.

stream channel.

DVD-V

AVCHD

ENG

Dolby D 3/2.1ch

48k

/ 3

1 During playback, press [SUBTITLE].

e.g.) DVD-video

2 Use [K / L] to select your desired

• For audio CD, you can select following options.

“Stereo”: Both right and left channels are active (stereo).

subtitle.

“L-ch”:

Only left channel is active.

Only right channel is active.

ENG

/ 4

“R-ch”:

3 Press [AUDIO] to exit.

• Use [{ B] to switch between current subtitle

setting and “Off”.

Note

3 Press [SUBTITLE] to exit.

• The secondary audio will not be output when the

secondary video is not displayed or when “BD Audio

Mode” is set to “HD Audio Output”.(For some BD,

secondary audio will be output even when secondary

video is off.)

• The sound mode cannot be changed during

playback of discs not recorded in multiple audio.

• Some discs allow to change audio language setting on

the disc menu. (Operation varies depending on the

discs. Refer to the manual accompanying the disc.)

• [AUDIO] may not work on some discs with multiple

audio streams or channels (e.g. DVD which allow to

change audio setting on the disc menu).

Note

• Some discs will only allow you to change the

subtitles from the disc menu or pop-up menu. Press

[TOP MENU] or [POP UP MENU / MENU] to display

the disc menu or pop-up menu.

• If 4-digit-language code appears in the subtitle

menu, refer to “LANGUAGE CODE” on page 54.

• If the disc has no subtitle language or subtitle style,

“Not Available” will be displayed on the TV screen.

• During playback of the secondary video, the primary

subtitle setting is not available except when there is

no subtitle for the secondary video.

• Secondary subtitle setting is only available during

playback of the secondary video.

• If you choose a language that has a 3-letter-language

code, the code will be displayed every time you

change the subtitle language setting. If you choose

any other Languages, “---” will be displayed instead

(refer to page 54).

•

If you select a language that has a 3-letter-language code,

the code will be displayed every time you change the

audio language setting. If you select any other languages,

“---” will be displayed instead (refer to page 54).

• If 4-digit-language code appears in the subtitle

menu, refer to “LANGUAGE CODE” on page 54.

• If the disc has no audio language, “Not Available” will

be displayed on the TV screen.

• For DTS-CD (5.1 music disc), “DTS“ will be displayed.

(Selecting audio streams or channels is not available.)

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL SETTINGS

2 Use [K / L] to select a memory from

Setting the BD Audio Mode

“Memory 1” to “Memory 5” to store your

setting, then press [ENTER].

BD-V

3 Use [K / L] to select a item to be

There are 2 ways to set “BD Audio Mode” setting;

whether to output the secondary and interactive audio

accompanied by the primary audio or only the primary

audio. Depending on the setting of the mode, Dolby

Digital, Dolby Digital Plus, Dolby TrueHD, DTS, or DTS-HD

output changes between multi LPCM and bitstream.

adjusted, then use [^{

adjust the setting.

B] or [ENTER] to

2. Brightness

1. Contrast

7. Noise Reduction

Off

In stop mode with BD inserted, press [MODE].

2 Use [K / L] to select your desired setting.

item

Description

Adjusts the

difference

adjustment range

BD Audio Mode

Mix Audio Output

between the

bright and dark

parts of the

picture.

1. Contrast

-7 to +7(0*)

“Mix Audio Output”:

If it is available, BD-video’s secondary and interactive

audio will be output with the primary audio.

Adjusts the

• The secondary audio is the audio for the secondary

video (Director’s comment etc.) and the interactive

audio is the audio for the interactive application

(Button click sounds etc.).

2. Brightness brightness of the 0 to +15(0*)

picture.

Adjusts the

sharpness of the

picture for

frequency range.

Detailed

“HD Audio Output”:

3. Sharpness

-6 to +6(0*)

Only the primary audio will be output. Set this mode in order

to output Dolby Digital, Dolby Digital Plus, Dolby TrueHD,

DTS or DTS-HD audio of BD through HDMI connection.

4. Gamma

adjustment of

0 to +5(0*)

-7 to +7(0*)

Correction the picture’s

brightness.

3 Press [RETURN] to exit.

• You can also set “BD Audio Mode” from the setup

menu. Refer to page 38.

Adjusts the bal-

ance between

green and red.

5. Color

Note

On*:Makes the dark

parts brighter.

Off :Shows the original

picture as recorded.

• In “Mix Audio Output” mode, if there is no secondary

and interactive audio, the audio will be output as

“HD Audio Output” mode.

Adjusts the black

level.

6. Black Level

• In “Mix Audio Output” mode, even if you set “HDMI

Multi(Normal)” in “HDMI Audio Out” setting, multi

LPCM will be output from HDMI OUT jack for BD

audio. Refer to page 14.

• In “Mix Audio Output” mode with HDMI audio being

output, 2-channel down-mixed LPCM will be output

from AUDIO OUTPUT (DIGITAL OPTICAL / COAXIAL)

jacks for BD audio.

• In “Mix Audio Output” mode with “HDMI Audio Out”

setting set to “Audio Mute” and “Digital Out”setting set

to “Bitstream”, DTS, DTS-HD and LPCM will be output as

Dolby Digital for BD audio. Refer to pages 14, 17.

Off*

:Executes MPEG

noise reduction

which reduces the

block noise and

mosquito noise

on the subtitle on

movie.

7. Noise

Reduction Reduces the

:Executes 3D noise

reduction which

detects and deletes

the noise by com-

paring each picture

frames.

:Executes both

MPEG noise reduc-

tion and 3D noise

reduction.

(Not

noise of the

available for playback picture.

BD/AVCHD)

• You can also set “ BD Audio Mode” setting from the

setup menu. Refer to page 38.

Adjusting the Picture

* Default setting

BD-V

DVD-V

AVCHD

Note

You can adjust the picture quality and store the setting

you have adjusted on memory 1-5.

• The setting remains even you turn the unit into the

standby mode except unplug the AC cord.

• For the picture output from HDMI OUT jack, “Black

Level” is not effective.

• For BD and AVCHD files, noise reduction is not

effective.

1 During playback, press [MODE]

repeatedly until the picture adjustment

menu appears.

Memory1

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

Using the Setup Menu

In the setup menu you can change the setting for audio,

video, language, etc. You cannot change the setting

during playback.

Setting items displayed in gray indicates they are not

available under the conditions at the time.

Quick

“Quick” menu contains setting items extracted from

“Custom” menu which may be used frequently.

In stop mode, press [SETUP].

Use [K / L] to select , then press

[ENTER].

Use [K / L] to select your desired

setting items.

Quick

Media Select

Disc

HDMI Audio Out

HDMI Video Resolution

Component Output

Player Menu

HDMI Multi (Normal)

Auto

480i

English

Follow the procedure below

depending on the setting items.

A) If “ B “ does not appear on the right side

of the setting items when you highlight

the items:

Press [ENTER] repeatedly to change

options.

B) If “

“ appears on the right side of the

setting items when you highlight the

items:

1) Press [ENTER].

2) Use [K / L] to select options, then press

[ENTER].

• Use [s] or [RETURN] to go back to the

previous screen.

Press [SETUP] to exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

Custom

“Custom” menu contains all the setting items.

In stop mode, press [SETUP].

Use [K / L] to select , then press

[ENTER].

Use [K / L] to select your desired

setting category, then press [ENTER].

: Language

: Video

: Audio

: Parental

: Others

• For “Parental” menu, follow the procedure on

page 42.

Use [K / L] to select your desired

setting items.

• The setting items which are not available with

current situation of this unit will be displayed

in gray and you cannot select them.

Follow the procedure below

depending on the setting items.

A) If “ B “ does not appear on the right side

of the setting items when you highlight

the items:

Press [ENTER] repeatedly to change

options.

B) If “

“ appears on the right side of the

setting items when you highlight the

items:

1) Press [ENTER].

2) Use [K / L] to select options, then press

[ENTER].

• Use [s] or [RETURN] to go back to the

previous screen.

Press [SETUP] to exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

■

Language

Audio

Original

Subtitle

Off

Disc Menu

Player Menu

English

• For how to select the setting items and options, refer to “Custom” on page 34.

Setting items

Options

Audio

Original* / English / French / Spanish / German / Italian / Swedish / Dutch /

Russian / Chinese / Japanese / Korean / Danish / Finnish / Norwegian /

Icelandic / Hungarian / Romanian / Turkish / Greek / Irish / Portuguese /

Polish / Czech / Slovak / Bulgarian / Other

Sets the language for audio.

Subtitle

Sets the language for subtitle.

Off* / English / French / Spanish / German / Italian / Swedish / Dutch /

Russian / Chinese / Japanese / Korean / Danish / Finnish / Norwegian /

Icelandic / Hungarian / Romanian / Turkish / Greek / Irish / Portuguese /

Polish / Czech / Slovak / Bulgarian / Other

Disc Menu

English* / French / Spanish / German / Italian / Swedish / Dutch / Russian /

Chinese / Japanese / Korean / Danish / Finnish / Norwegian / Icelandic /

Hungarian / Romanian / Turkish / Greek / Irish / Portuguese / Polish / Czech /

Slovak / Bulgarian / Other

Sets the language for disc menu or

pop-up menu.

Auto(XXXX)*¹/ English* / Français / Español

Player Menu

Sets the language for OSD

(on-screen display).

*) Settings with (*) are the default.

*¹) “ Auto” activates the Get & Set Menu Language function. (Refer to page 44)

- “Auto” is available only when “HDMI CEC” is set to “On”.

- Inside the parentheses next to “Auto” will be the language which is currently selected by your TV.

• “Quick” menu consists of the setting menus frequently used, and they are accompanied with

• If you select “Other”, enter the 4-digit-number code for the desired language (Refer to “LANGUAGE CODE” on

page 54). Only the languages supported by the disc can be selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

■

Video

TV Aspect

16:9 Wide

HDMI Video Resolution

HDMI Deep Color

Component Output

Progressive Mode

Still Mode

Auto

480i

Auto

• For how to select the setting items and options, refer to “Custom” on page 34.

Setting items Options

TV Aspect

16:9 Wide*:

Sets the picture size according to

aspect ratio of the connected TV.

Select this when a wide-screen TV is connected. Discs recorded in wide-

screen format is played back over the entire TV screen.

4:3 Pan & Scan:

Select this to play back the discs recorded in wide-screen format with 4:3 TV

in the pan & scan mode (with the sides of the picture cut off). Discs which are

not specified for pan & scan are played back in the letter box mode.

4:3 Letter Box:

Select this to play back the discs recorded in wide-screen format with 4:3

TV in the letter box mode. (with black strips at the top and bottom).

16:9 Squeeze:

When playing back 4:3 images, the picture is displayed in the center of the

16:9 screen with a 4:3 aspect ratio.

Auto*:

HDMI Video Resolution

Sets the HDMI video resolution.

HDMI video resolution will be selected automatically depending on the

connected HDMI device.

480p

720p

1080i

1080p

1080p24:

Gives a natural and high quality film reproduction of 24-frame film

material. The connected TV has to be compatible with 1080p24 frame

input.

HDMI Deep Color

Auto*:

Sets whether to output the picture

from HDMI OUT jack with Deep

Color or not.

The picture from HDMI OUT jack will be output with Deep Color to the

connected TV which supports HDMI Deep Color.

Off:

The picture from HDMI OUT jack will be output without Deep Color.

480i*

480p

720p

1080i

Auto*:

Component Output

Sets the video resolution for

component output.

Progressive Mode

Sets the optimum progressive

mode for the image material

output from HDMI OUT jack and

VIDEO OUTPUT (COMPONENT)

jacks.

The progressive mode will detect 24-frame film material (movies) and

automatically select appropriate progressive mode.

Video:

Suited for playing back video material discs (TV shows or animation).

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

Setting items

Still Mode*¹

Options

Auto*:

Adjusts picture resolution and

Automatically selects the best resolution setting (“Frame” or “Field”) based

on the data characteristics of the pictures.

quality in still mode.

Field:

Stabilizes the pictures, although the picture quality may become coarse

due to the limited amount of data. Select “Field” when the pictures are still

unstable even if “Auto” is selected.

Frame:

Displays relatively motionless pictures in higher resolution. “Frame”

improves the picture quality, although it may unstabilize the pictures due

to alternate output of 2-field data.

*) Settings with (*) are the default.

*¹) An individual picture on the TV screen is called “Frame”, which consists of two separate images called “Field”.

Some pictures may be blurred at the auto setting in “Still Mode” setting due to their data characteristics.

• “Quick” menu consists of the setting menus frequently used, and they are accompanied with

• If you set “HDMI Video Resolution” setting to “1080p24” and the contents of the BD are not compatible for

1080p24 frame, 1080p60 frame will be output.

• If the picture is not output properly to the TV because of “HDMI Video Resolution” or “Component Output”

setting, press and hold [PLAY B] on the front panel for more than 5 seconds. Both settings will be reset to the

default automatically.

• If an HDMI cable is connected, for video resolution for the component output, you can only select video

resolution that currently output from HDMI OUT jack or “480i”.

• If the video resolution for the component output and HDMI video resolution do not match, the video resolution

for the component output will be switched to “480i”. VIDEO OUTPUT (COMPONENT) jacks may not output any

signals depending on the disc material.

• If you play back copy-protected DVD-video, 480p signal will be output from VIDEO OUTPUT (COMPONENT) jacks,

when “Component Output” setting is set to “720p” or “1080i”.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

■

Audio

BD Audio Mode

HDMI Audio Out

Down Sampling

DRC

HD Audio Output

HDMI Multi (Normal)

Auto

• For how to select the setting items and options, refer to “Custom” on page 34.

Setting items Options

BD Audio Mode

HD Audio Output*:

For BD, selects whether to output

the secondary and interactive

audio with primary audio if it is

available or only the primary

audio. Refer to “Setting the BD

Audio Mode” on page 32.

Outputs only the primary audio. Set this mode in order to output Dolby

Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD audio of BD

through HDMI connection.

Mix Audio Output:

Outputs the secondary and interactive audio with primary audio if it is available.

HDMI Multi(Normal)*:

HDMI Audio Out

The multi-channel audio signals are output from HDMI OUT jack with

bitstream or LPCM.

HDMI Multi(LPCM):

The multi-channel audio signals are output from HDMI OUT jack with LPCM.

• Refer to pages 39-41 for setting options.

Sets the audio format for the audio

output from HDMI OUT and

AUDIO OUTPUT

(DIGITAL OPTICAL / COAXIAL)

jacks.

HDMI 2ch:

The audio signals are output from the HDMI OUT jack with a downmixed to

2ch LPCM.

Audio Mute:

Mutes the HDMI audio signal, and set the signal format from AUDIO OUTPUT

(DIGITAL OPTICAL / COAXIAL) jacks.

• Refer to “Digital out setting” on page 39 for setting options.

Down Sampling

On*:

Sets the digital audio output

when playing back BD or DVD

recorded in LPCM.

LPCM signals are converted to 48 kHz for output.

• Set to “On” when using digital connections to an AV receiver that is not

compatible with sampling frequencies of 96 kHz.

Off:

For BD and DVD recorded in LPCM without copyright protection, 2-channel

audio signals up to 192 kHz are output as LPCM signals with no conversion.

DRC

Auto*:

Sets whether to compress the

range of sound volume (dynamic

range control) when Dolby Digital,

Dolby Digital Plus or Dolby

When the discs recorded in Dolby TrueHD format are in playback, this unit detects

DRC setting of the disc and set “DRC” setting to “On” or “Off” automatically.

Off

TrueHD audio is played back.

*) Settings with (*) are the default.

• “Quick” menu consists of the setting menus frequently used, and they are accompanied with

• Under following circumstances, “HDMI Multi(Normal)”, “HDMI Multi(LPCM)” and "HDMI 2ch" are not available.

- HDMI cable is not connected to HDMI OUT jack.

- Connected TV is off.

- Connected TV is not compatible with audio output.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

■ Digital out setting

When “Audio Mute” is selected in “HDMI Audio Out” setting, HDMI audio signal will be muted and the audio signals

output from AUDIO OUTPUT (DIGITAL OPTICAL / COAXIAL) jacks change depending on “Digital Out” setting.

Quick HDMI Audio Out Audio Mute Digital Out

Bitstream*:

When playing back discs recorded in Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD,

the corresponding core stream (Dolby Digital or DTS) are output.

LPCM:

LPCM signal will be output from AUDIO OUTPUT (DIGITAL OPTICAL / COAXIAL) jacks.

• This setting is not effective when the HDMI audio signal is output.

■ Speaker setting

This unit allows you to enjoy multi-channel surround sound such as 7.1-channel / 5.1-channel surround.

Front speaker (left)

Front speaker (right)

Center speaker

Subwoofer

Surround speaker (left)

Surround speaker (right)

Surround back speaker (left)

Surround back speaker (right)

e.g.) basic layout with 7.1-channel surround system

To make the most of its feature, set up your speakers appropriately by referring to the following table.

Speaker setting options are available at the following locations;

(Available when you have HDMI cable connected to HDMI OUT jack)

Quick HDMI Audio Out HDMI Multi(LPCM)

Custom Audio HDMI Audio Out HDMI Multi(LPCM)

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

How to navigate through “HDMI Multi(LPCM)”.

1 Use [K / L] to select your desired menu item then press [ENTER].

2 Use [K / L] to select your setting items.

• Press [RETURN] to go back to the previous screen.

3 Use [s

B] to select desired options. (Except for “Test Tone”, “Default” and setting

options in “Speaker Size” setting.)

For setting options in “Speaker Size” setting:

Press [ENTER] to select desired options.

For “Test Tone”:

Use [^s

• The test tone will be output. If you select “Manual”, use [K / L] to select desired speaker, then use [s

the volume. If you select “Auto”, use [^sB] to adjust the volume of the speaker that outputs the test tone.

B] to select “Off”, “Manual” or “Auto”, then press [ENTER].

B] to adjust

• If you want to stop the test tone, press [RETURN].

For “Default”:

Press [ENTER] to reset to the default.

4 Press [SETUP] to exit.

Speaker Size

Setting items

Front

Options

Large*

Descriptions

Large:

Selects the desired

speaker to set. Then

change the setting

appropriately by

referring to the

For the large speakers with strong low

frequency reproduction capabilities.

Small:

For the small speakers which do not

provide strong bass sound.

You cannot change the setting of

“Subwoofer”. If connected device is not

compatible with subwoofer, “Subwoofer”

will be displayed in gray.

Small

Large*

Small

Center

Subwoofer

Surround

descriptions.

Large*

Small

Large*

Small

Surround Back

Default

Select “Default”, then press [ENTER] to

reset “Speaker Size” setting to the default.

Channel Level

Test Tone:

Off*

Select “Off” to deactivate “Test Tone”.

Tests or sets the volume

for each speaker.

“Test Tone” is the

test tone which

can be output

Select “Manual”, then press [ENTER] to

manually set the volume for the desired

speaker.

Manual

Auto

from the speakers

so that you can

adjust the volume

for each speaker.

Select “Auto”, then press [ENTER] to

automatically output the test tone from

each speaker.

Front Lch

0 dB to -12 dB

(0 dB*)

0 dB to -12 dB

(0 dB*)

0 dB to -12 dB

(0 dB*)

0 dB to -12 dB

(0 dB*)

If you have selected “Manual” in “Test

Tone”, select the desired speaker to set

and adjust the volume for the selected

speaker.

If you select “Auto” in “Test Tone”, test

tone will automatically be output in order.

Adjust the volume of the speaker that

outputs the test tone.

Center

Subwoofer

Front Rch

Surround Rch

0 dB to -12 dB

(0 dB*)

Surround Back

Rch

0 dB to -12 dB

(0 dB*)

Surround Back

Lch

0 dB to -12 dB

(0 dB*)

Surround Lch

0 dB to -12 dB

(0 dB*)

Default

Select “Default”, then press [ENTER] to

reset “Channel Level” setting to the

default.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

Delay Time

Setting items

Distance

Options

Descriptions

Set the desired measure system. This

measure system will be used for

Feet*

This is a parameter for

optimizing the timing at

which the sound is

output from the

speakers according to

their distance from the

listening position.

Meters

“Delay Time” setting. Press [ENTER] (or

B]) to switch the settings.

Front

0ft to 60ft (12ft*)

(0m to 18m (3.6m*))

0ft to 60ft (12ft*)

Select the distance from the listening

position to the speaker to get the ideal

delay time.

Center

(0m to 18m (3.6m*))

Surround

Surround Back

Default

0ft to 60ft (10ft*)

(0m to 18m (3.0m*))

0ft to 60ft (10ft*)

(0m to 18m (3.0m*))

Select “Default”, then press [ENTER] to

reset “Delay Time” setting to the default.

*) Settings with (*) are the default.

• For “Speaker Size” setting, the settings of each speaker size may be adjusted automatically corresponding to

each setting. (e.g. If “Front” is set to “Small”, you cannot set “Center”, “Surround”, and “Surround Back” to “Large”.)

• For “Delay Time”, the difference between the value of the “Front”, “Surround” and “Surround Back” setting

cannot exceed 15 ft (4.5m), and the difference between the value of the “Front” and “Center” setting cannot

exceed 5 ft (1.5m).

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

■

Parental

Ratings control allows you to set a limit, which prevents your children from viewing inappropriate materials. Playback

will be stopped if the ratings exceed the levels you set, and it will require you to enter a password before playing back

the disc.

Parental

BD Rating Level

DVD Rating Level

Password Change

All

1 Use [K / L] to select , then press [ENTER].

2 Use [the Number buttons] to enter your 4-digit password.

For the first time use: Use [the Number buttons] to enter any 4-digit number (except for 4737), then press [ENTER].

That number will be used as the password from the second time. Record your password in case you forget it.

• If you forget the password, enter [4], [7], [3], [7]. The password will be cleared and rating level will be set to “All”.

• While you input the password, press [CLEAR] to clear the number, then re-enter the password.

3 Proceed to A – C

A) BD Rating Level

1) Use [K / L] to select “BD Rating Level”, then press [ENTER].

2) Use [K / L] to select your desired option, then press [ENTER].

“All”:

To release the limitation.

“Age Setting”: To set the age limitation.

• After selecting “Age Setting”, use [the Number buttons] to enter the age from 0 – 254. (e.g. for age 15, press

[0], [1], [5])

3) Press [SETUP] to exit.

B) DVD Rating Level

1) Use [K / L] to select “DVD Rating Level”, then press [ENTER].

2) Use [K / L] to select your desired level, then press [ENTER].

3) Press [SETUP] to exit.

RATING EXPLANATIONS

• All

: Parental control is inactive; all discs can be played back.

: DVD software of any grades (adult/general/children) can be played back.

: No one under 17 admitted.

• 8 [Adult]

• 7 [NC-17]

• 6 [R]

: Restricted; under 17 requires accompanying parent or adult guardian.

: Parental guidance recommended.

: Unsuitable for children under 13.

: Parental guidance suggested.

: General audience.

• 5 [PGR]

• 4 [PG-13]

• 3 [PG]

• 2 [G]

• 1 [Kid Safe] : Suitable for children.

C) Password Change

1) Use [K / L] to select “Password Change”, then press [ENTER].

2) Enter a new 4-digit password, then press [ENTER].

3) Press [SETUP] to exit.

Note

• The resume information will be cleared if you change the parental level when the resume information is on.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

■

Others

Angle Icon

Auto Power Off

Panel Display

HDMI CEC

Auto

Media Select

Disc

Network Connection

Software Upgrade

Enable(Easy)

• For how to select the setting items and options, refer to “Custom” on page 34.

Setting items Options

Angle Icon

On*:

The angle icon appears on the TV screen when playing back the scene with various

angle.

Off:

The angle icon disappears on the TV screen.

Auto Power Off

On*:

If this unit is left with no activity for more than 30 minutes, this unit turns into the

standby mode automatically.

Off:

Sets off the auto power off.

Panel Display

Auto*:

Sets the brightness of the

front panel display.

Front panel display gets darker during playback.

Bright:

Front panel display gets brighter.

Dimmer:

Front panel display gets darker.

HDMI CEC

On*

Sets whether to utilize

HDMI CEC function.

Off

Disc*:

Media Select

Select this when you play back a disc.

SD Card:

Selects the media to

playback.

Setting will be back to

“Disc” when you turn the

unit to the standby mode.

Select this when you play back an SD Memory Card.

Network Connection

Connection

Test

Perform the network connection

test. After you change the IP

address or DNS setting, always

perform this test.

Enable(Easy)*

If you select “Enable(Easy)”,

Connection test will automatically

start.

Enable

(Custom)

IP Address Auto(DHCP)*

Set the IP address.

Setting

In most cases, you can connect

to the Internet without making

any changes to the default

setting.

Manual

IP Address

Subnet Mask

Default

Gateway

DNS

Setting

Set the DNS setting.

Auto(DHCP)*

Manual

In most cases, you can connect

to the Internet without making

any changes to the default

setting.

Primary DNS

Secondary

DNS

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

Setting items

Options

Network Connection

Enable

(Custom)

Proxy

Setting

Do Not Use*

Use

Set the proxy server.

In most cases, you can connect

to the Internet without using

proxy server.

Proxy

Address

Proxy Port

Connection Auto*

Speed

Set the connection speed.

In most cases, you can connect

to the Internet without making

any changes to the default

setting.

10BASE Half

10BASE Full

100BASE Half

100BASE Full

Allow*

BD-Live

Setting

You can restrict Internet access

Limited Allow when BD-Live

functions are used.

Limited Allow

Prohibit

Disable

Deactivate the network

connection.

Software Upgrade

Current Version :

Allows you to upgrade this Indicates the current firmware version.

unit’s firmware.

Refer to page 48.

Disc Upgrade :

Allows you upgrade this unit’s firmware using a disc.

Network Upgrade :

You can upgrade the firmware version by connecting this unit to the Internet.

*) Settings with (*) are the default.

• HDMI CEC allows integrated system control over HDMI and is part of the HDMI standard. In addition to Onkyo AV

components, it allows interoperability with CEC-compatible AV components and TVs made by other manufacturers.

• When “HDMI CEC” setting is set to “On”, functions listed below will be available.

Direct Change

When this unit is turned on, the TV also is turned on and the appropriate external input channel will be selected

automatically. The appropriate external input channel can also be selected on your TV automatically when you

press [PLAY B] when the unit’s power is on.

Standby

When you press and hold [ /y ON / STANDBY] on the front panel for 2 seconds, it turns off the power of the TV

first and then turns off the power of this unit also.

System Information

Get & Set Menu Language

• The unit recognizes the OSD language set for the TV and automatically sets the same language as the player

menu language (OSD menu language) for this unit.

• This feature is available only when “Auto(XXXX)” is selected in “Player Menu” in the setup menu. (Refer to “Player

Menu” on page 35.)

Note

•

HDMI CEC is available only when the display device is connected by an HDMI cable, and when it supports HDMI CEC feature.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

Enable(Easy)

Network settings are set to the following settings initially.

(In most cases, you can connect to the Internet without

making any changes to the default settings.)

Network Connection

Set up the network connection settings in order to use

the BD-Live function with a BD-Live disc.

- IP Address Setting

- DNS Setting

- Proxy Setting

- Connection Speed

- BD-Live Setting

Auto(DHCP)

Do Not Use

Auto

Connection Test

After you made IP address/DNS settings or when a LAN

cable is connected, always perform the connection test

to check if the connection is correctly made.

Allow

1 In stop mode, press [SETUP].

2 Use [K / L] to select , then press

If you want to set the network settings back to the default

settings as above (except “BD-Live Setting”), follow the

procedure below.

[ENTER].

3 Use [K / L] to select “Others”, then press

1 Follow steps 1 to 4 in “Connection Test” on

[ENTER].

this page.

4 Use [K / L] to select “Network

2 Use [K / L] to select “Enable(Easy)”, then

Connection”, then press [ENTER].

press [ENTER].

5 Use [K / L] to select “Connection Test”,

• The unit will start the connection test automatically

and the test result will appear right after the test

finishes.

then press [ENTER].

Connection test will start automatically and the test

result will appear right after the connection test finishes.

• “Testing...” : The test is in progress.

• After the connection test finishes, press [ENTER] to

go to network status confirmation screen.

• “Pass” : Connection test is successfully completed.

• “Fail” : Connection test failed. Check the connection

settings.

3 Press [ENTER] to activate the network

settings and set the network connection

automatically. Press [SETUP] to exit.

Press [ENTER] to go to the list of network status

confirmation screen.

Note

• The setting of “BD-Live Setting” will not be set back to

the default, even if you follow the procedure.

Others

Connection Test

Enable(Custom)

In following cases, select “Enable(Custom)” to set each

setting as necessary.

IP Address

xxx.xxx.xxx.xxx

Subnet Mask

Default Gateway

Primary DNS

Secondary DNS

- When connection test failed with the setting of

“Enable(Easy)”.

- When instructed by your Internet service provider to make

specific settings in accordance with your network

environment.

then press ‘ENTER’.

6 Press [ENTER] to go back to the previous

• IP Address Setting / DNS Setting

screen, or press [SETUP] to exit.

1 Follow steps 1 to 4 in “Connection Test”

Note

on this page.

• If the connection test passes, you can enjoy the

BD-Live functions using the Internet without making

any extra settings.

2 Use [K / L] to select “Enable(Custom)”,

then press [ENTER].

• If the connection test fails, you may need to change

the MAC address settings of your router.

• "Connection Test" is not available when "Disable" is

selected in "Network Connection".

3 Use [K / L] to select “IP Address Setting”,

then press [ENTER] repeatedly to select

the desired setting.

“Auto(DHCP)”:

If your router has DHCP server

function, select “Auto(DHCP)”.

“Manual”:

If your router does not have DHCP

server function, select “Manual”.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

3-d) After you enter all correctly, press [ENTER].

If you select “Manual”, follow the following

• Confirmation message will appear. Select “Yes” to

complete the settings.

instruction to set the IP address and DNS.

3-a) Use [K / L] to select “IP Address”, “Subnet Mask” or

“Default Gateway”, then press [ENTER]. IP address

setting screen will appear. Enter IP address, subnet

mask and default gateway with cursor buttons and

number buttons.

Others

DNS Setting

Is Setting OK?

Primary DNS

xxx . xxx . xxx . xxx

Others

IP Address Setting

Secondary DNS

IP Address

Yes

xxx xxx xxx xxx

Subnet Mask

xxx xxx xxx xxx

Default Gateway

xxx xxx xxx xxx

then press ‘ENTER’.

4 Press [RETURN] to go back to the previous

screen, or press [SETUP] to exit.

Note

• The range of input number is between 0 and 255.

• If you enter a number larger than 255, the number will

automatically be 255.

• Enter the IP address number after checking the

specifications of your router.

• If the IP address number is unknown, check the IP

address number of other devices. (e.g. PC

connected via LAN cable) and assign a different

number from those of other devices.

3-b) After you enter all correctly, press [ENTER].

• Confirmation message will appear. Select “Yes” to

complete the settings.

• The manually entered number will be saved even if

you change the setting to “Auto(DHCP)”.

• When you enter a wrong number, press [CLEAR] to

cancel. (the number will be back to “0”.)

• If you want to enter 1 or 2 digit number in one cell,

press [B] to move on to the next cell.

• If the entered IP address or the default gateway or

primary DNS number is same as the default setting, IP

address setting will be set to “Auto(DHCP)”. (The

manually entered number will be saved.)

• When IP address setting is set to “Manual”, the setting

of DNS setting will automatically be “Manual” and

when IP address setting is set to “Auto(DHCP)”, you

can set either “Auto(DHCP)” or “Manual” for DNS

setting.

Others

IP Address Setting

Is Setting OK?

IP Address

xxx . xxx . xxx . xxx

Subnet Mask

Default Gateway

• Proxy Setting

Yes

1 Follow steps 1 to 4 in “Connection Test”

on page 45.

3-c) Use [K / L] to select “Primary DNS” or “Secondary

DNS”, then press [ENTER]. DNS setting screen will

appear. Enter primary DNS and secondary DNS with

cursor buttons and number buttons.

2 Use [K / L] to select “Enable(Custom)”,

then press [ENTER].

3 Use [K / L] to select “Proxy Setting”, then

press [ENTER] repeatedly to select the

desired setting.

Others

DNS Setting

• For default settings, select “Do Not Use”.

• If you need to change the proxy setting as instructed

by your Internet service provider to set the

designated proxy address and port, select “Use”.

Primary DNS

xxx xxx xxx xxx

Secondary DNS

If you select “Use”, follow the following

instructions to set the proxy address and

proxy port.

xxx xxx xxx xxx

then press ‘ENTER’.

• Enter the numbers instructed by your Internet

provider.

• If the number is unknown, check the number of

other devices (e.g. PC connected via LAN cable) and

assign the same number.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

3-a) Use [K / L] to select “Proxy Address”, then press

• Connection Speed

You can set connection speed as your preference. (The

default setting is “Auto”.)

[ENTER]. Proxy address setting screen will appear.

Enter proxy address.

• The keyboard screen will appear.

1 Follow steps 1 to 4 in “Connection Test”

on page 45.

Others

Proxy Address

2 Use [K / L] to select “Enable(Custom)”,

then press [ENTER].

3 Use [K / L] to select “Connection Speed”,

4 5 6 7 8

then press [ENTER].

c d e f g h

4 Use [K / L] to select the desired setting,

m n o p q r s

- _ OK

then press [ENTER].

Clear

All Clear

a/A/@

“Auto”:

Set the appropriate connection speed automatically, in

accordance with your network environment.

[K / L/

B] : Move the highlight.

[the Number buttons] : Enter number.

“10BASE Half”:

Set the connection speed to “10BASE Half”.

[ENTER] : Enter the highlighted number/word.

[A] : Clear the entered number or word.

[B] : Clear all the entered numbers or words.

[C] : Switch between abc ? ABC ? @!?

[D] : Set the entered number or word.

“10BASE Full”:

Set the connection speed to “10BASE Full”.

3-b) After you enter proxy address correctly, press [D].

• Confirmation message will appear. Select “Yes” to

complete the settings.

“100BASE Half”:

Set the connection speed to “100BASE Half”.

“100BASE Full”:

Set the connection speed to “100BASE Full”.

Others

Proxy Address

5 Press [RETURN] to go back to the

previous screen, or press [SETUP] to exit.

Is Setting OK?

xxxxx

Note

• Choose a connection speed in accordance with your

network environment.

• The network connection may be disabled depending

Yes

on the device, when the settings are changed.

• BD-Live Setting

You can limit the Internet access from the BD-Live

functions. (The default setting is “Allow”.)

3-c) Use [K / L] to select “Proxy Port” , then press

[ENTER]. Proxy port setting screen will appear.

Enter proxy port number with number buttons.

1 Follow steps 1 to 4 in “Connection Test”

on page 45.

Others

Proxy Port

2 Use [K / L] to select “Enable(Custom)”,

then press [ENTER].

Please select the input Proxy Port.

then press ‘ENTER’.

xxxxx

3 Use [K / L] to select “BD-Live Setting”,

then press [ENTER].

4 Use [K / L] to select the desired setting,

then press [ENTER].

“Allow”:

Internet access is permitted from all BD-Live contents.

3-d) After you enter proxy port correctly, press [ENTER].

“Limited Allow”:

Internet access is permitted only for BD-Live contents

which have content owner certificates. Internet access

without the certificates are prohibited.

4 Press [RETURN] to go back to the

previous screen, or press [SETUP] to exit.

Note

“Prohibit”:

Internet access is prohibited from all BD-Live contents.

• The range of input number for the port number is

between 0 and 65535. (If you enter a number larger

than 65535, it will be regarded as 65535.)

• For proxy port, the selected ports may be blocked and

not be able to use depending on your network

environment.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

5 Disc tray will open automatically.

5 Press [RETURN] to go back to the

• Insert the disc for software upgrade and then press

previous screen, or press [SETUP] to exit.

[OPEN/CLOSE A].

Disable

6 After completing loading disc,

confirmation message will appear. Select

“Yes” and press [ENTER] to start

upgrading.

Deactivate all the network connection and settings.

1 Follow steps 1 to 4 in “Connection Test”

on page 45.

• It may take a while to complete the upgrading.

(Please wait until “100%” appears on the front panel

display.)

2 Use [K / L] to select “Disable”, then

press [ENTER].

3 Press [RETURN] to go back to the

7 After the disc upgrade finishes, this unit

previous screen, or press [SETUP] to exit.

will restart and eject the disc.

Note

• The network connection can be reactivated by setting

the network connection to “Enable(Easy)” or

“Enable(Custom)”.

• Please do not unplug the AC power code while

executing the “Disc Upgrade”.

• All settings will remain the same even if you upgrade

the firmware version.

Software Upgrade

Network Upgrade

Current Version

You can confirm the current software version.

You can upgrade the software by connecting the unit to

the Internet.

1 Follow steps 1 to 3 in “Connection Test”

on page 45.

2 Use [K / L] to select “Software Upgrade”,

then press [ENTER].

3 Use [K / L] to select “Network Upgrade”,

3 Use [K / L] to select “Current Version”,

then press [ENTER].

4 Use [K / L] to select “Yes”, then press

[ENTER].

Others

Current Version

• This unit will then start checking for the latest

firmware version.

Current Version

x.xxx

5 Confirmation message will appear.

Use [K / L] to select “Yes”, then press

[ENTER].

If you wish to check latest upgrade

or other product information,

please check our Website.

www.onkyo.com

• The unit will start downloading the latest firmware

version.

6 When the download completes,

confirmation message will appear. Press

[ENTER].

4 Press [ENTER] or [RETURN] to exit.

• The unit will start upgrading the firmware version.

• It may take a while to complete the upgrading.

(Please wait until “100%” appears on the front panel

display.)

Note

• Please visit www.onkyo.com to download the latest

firmware version.

7 After upgrading finishes, this unit will

restart and open the disc tray

automatically.

Disc Upgrade

You can upgrade the software by using disc.

1 Follow steps 1 to 3 in “Connection Test”

Note

on page 45.

• Please do not unplug the AC power code or LAN cable

while executing the “Network Upgrade”.

• All settings will remain the same even if you upgrade

the software version.

2 Use [K / L] to select “Software Upgrade”,

then press [ENTER].

3 Use [K / L] to select “Disc Upgrade”,

• The disc tray will open automatically after upgrading

then press [ENTER].

finishes. This is not a malfunction.

4 Use [K / L] to select “Yes”, then press

[ENTER].

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION SETUP

Initialize

Initialize the setting or SD Memory Card.

In stop mode, press [SETUP].

Use [K / L] to select , then press

[ENTER].

Use [K / L] to select a desired option,

then press [ENTER].

“Setup”: Resets the setup menu to the default.

The setting for “Parental”, “Network

Connection”and “Media Select” will

not be reset.

“Format SD Card” (Available only when an SD

Memory Card is inserted.):

Initializes the SD Memory Card.

“Erase Saved BD-ROM Data (Player)”:

Clears the data saved for the BD-ROM

contents, such as BD-ROM game

scores, from this player.

“Erase Saved BD-ROM Data (SD Card)”

(Available only when an SD Memory Card is

inserted.):

Clears the supplemental data for the

BD-ROM playback, such as subtitle data,

from the SD Memory Card.

“Network Settings”:

Resets the Network Settings menu to the

default.

Initialize

Setup

Format SD Card

Erase Saved BD-ROM Data (Player)

Erase Saved BD-ROM Data (SD Card)

Network Settings

Confirmation message will appear.

Use [K / L] to select “Yes”, then

press [ENTER].

Press [SETUP] to exit.

Caution

• Do not remove the SD Memory Card while executing

the “Format SD Card” or the “Erase Saved BD-ROM

Data (SD Card)”. It damages the card.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

If the unit does not perform properly when operated as instructed in this manual, check the unit, consulting the

following checklist.

Problem

Solution

No power

- Check if the AC cord is properly connected.

- Unplug the AC cord once, and wait for 5-10 seconds and then plug it in again.

No sound or picture

- Check if the connected TV is turned on.

- Check if the connections are made securely and correctly.

- Check whether the connected TV or other device supports HDCP. (This unit will

not output a video signal unless the other device supports HDCP.)

- Check whether the output format of this unit (HDMI FORMAT) matches the

supported input format of other connected device.

- When this unit is connected to the DVI jack on your TV or AV receiver, you

cannot hear any sound from the HDMI OUT if your TV or AV receiver only

supports DVI.

Distorted picture

- Sometimes a small amount of picture distortion may appear.

This is not a malfunction.

- Connect this unit directly to the TV. If the RCA audio / video cables are

connected to a VCR, pictures may be distorted due to the copy right protection

system.

Completely distorted picture or

black / white picture with BD / DVD

- Make sure the disc is compatible with this unit.

No sound or distorted sound

- Adjust the volume.

- Check that the speakers are connected correctly.

- Check the HDMI connections.

- Check the settings in “Audio” menu.

Picture freezes momentarily

during playback

- Check the disc for fingerprints / scratches and clean with a soft cloth wiping

from center to edge.

- Clean the disc.

Disc cannot be played back

- Clean the disc.

- Ensure the disc label is facing up.

- Check if the disc is defective by trying another disc.

- Cancel the ratings control or change the control level.

- Insert a correct disc that can be played back on this unit.

SD Memory Card cannot be read. - The format of the card does not match to this unit or the card is not compatible.

No return to start-up screen

when disc is removed

- Reset this unit by turning it off, then on again.

The unit does not respond to the - Aim the remote control directly at infrared sensor window on the front panel.

remote control

- Reduce the distance to infrared sensor window.

- Replace the batteries in the remote control.

- Re-insert the batteries with their polarities (+ / - signs) as indicated.

- Check if a strong light source is not interfering with this unit's infrared sensor.

Make sure that the unit is not subjected to direct sunshine or inverter-type

fluorescent lights. Relocate if necessary.

- If the BD player is installed in a cabinet with colored glass doors, the remote

control may not work reliably when the doors are closed. Open the doors, or use

a cabinet without colored glass.

Buttons do not work or the unit - To completely reset the unit, unplug the AC cord from the AC outlet for 5-10

stops responding

seconds.

The unit does not respond to

some operating commands

during playback

- Operations may not be permitted by the disc.

Refer to the instructions of the disc.

The unit cannot read BD / DVD / - Condensation? (Let sit 1 or 2 hours)

- You are attempting to playback a disc other than one with one of the marks on

page 19.

- Wipe the dirt off the disc or replace the disc.

Angle does not switch

- The angle cannot be switched for BD / DVD which do not contain multiple

angles. In some cases multiple angles are only recorded for specific scenes.

Playback does not start when

the title is selected

- Check the settings in “Parental” menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Problem

Solution

The password for rating level has - Enter the default password “4737”, then your forgotten password will be cleared.

been forgotten

Cannot connect the network

- Check if the LAN cable connection is properly made.

- Turn on the modem or broadband router.

- Check the network setting.

- Check if the broadband router and/or modem is correctly connected.

- Check the “BD-Live Setting”.

Cannot connect to the network - Check the content of your Internet service contract to see if your Internet service

while my PC is connected to the

network

provider prevents multiple terminals connecting at the same time.

Cannot use the BD-Live function - Use an SD card with enough space.

The playback of BD-video or

download of data does not

perform properly.

- Check if an SD Card is correctly inserted.

Do not remove the card during playback as some BD-videos require an SD Card

during playback.

“HDCP NOK” appears on the

front panel display

“HDCP NOK” appears under the following conditions:

- When the connected device does not support HDCP.

- When the connected device is recognized as an HDCP incompatible by HDMI SRM.

- When the connected device supports HDCP but cannot be recognized as an HDCP

compatible for some reason.

The BD player contains a microcomputer for signal processing and control functions. In very rare situations, severe

interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this

happens, unplug the power cord from the wall outlet, wait at least 5 seconds, and then plug it back in again.

Note

• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this

manual for details on correct operations.

• Some functions are prohibited on some discs.

Download from Www.Somanuals.com. All Manuals Search And Download.

GLOSSARY

Analog Audio

Dolby Digital Plus

An electrical signal that directly represents sound.

Dolby Digital Plus is the next generation digital audio

compression technology developed as an extension to

Compare this to digital audio which can be an electrical

signal, but is an indirect representation of sound. See also Dolby Digital. Blu-ray Disc supports 7.1 multi-channel

“Digital Audio”.

surround sound output.

Aspect Ratio

Dolby TrueHD

Dolby TrueHD is a lossless coding technology developed

for next generation optical discs. Blu-ray Disc supports 7.1

multi-channel surround sound output.

The width of a TV screen relative to its height.

conventional TVs are 4:3 (in other words, the TV screen is

almost square); widescreen models are 16:9 (the TV

screen is almost twice as wide as it is high).

DTS (Digital Theater System)

AVCHD

DTS is a multi-channel surround sound system. You can

enjoy movie dynamic and realistic sound like movie

theater. DTS surround sound technologies were developed

by DTS, Inc.

AVCHD is a new format for high definition video

camcorders which can record and play high-resolution

HD images.

BD-Java

DTS-HD

With some BD which support Java applications, you can

enjoy the interactive functions such as games or

interactive menus.

DTS-HD is a lossless coding technology developed as an

extension of the original DTS Coherent Acoustics format.

Blu-ray Disc supports 7.1 multi-channel surround sound

output.

BD-Live

Gateway

BD-Live is a BD-video (BD-ROM version 2 Profile 2.0/

Profile 1.1) which contains new functions (e.g. Internet

connection), in addition to the BONUSVIEW function.

IP address of the electronic devices (such as router) which

provide Internet access.

Blu-ray Disc (BD)

HDMI (high-definition multimedia interface)

Blu-ray Disc is a next generation optical video disc which

A digital interface between audio and video source. It can

is capable of storing much more data than a conventional transmit component video, audio, and control signal with

DVD. The large capacity makes it possible to benefit from

the features such as high-definition videos, multi-channel

surround sounds, interactive menus and so on.

one cable connection.

Hub

A device used for connecting multiple device to the

network.

Chapter

Just as a book is split up into several chapters, a title on a

BD-video or DVD-video is usually divided into chapters.