TX-NR702,602_En.book Page 1 Tuesday, September 7, 2004 1:18 PM
Contents
Introduction ...............................2
AV Receiver
Connections ............................21
First Setup ...............................39
Basic Operation ......................53
Advanced Operation...............64
Advanced Setup......................68
Zone 2 ......................................76
TX-SR702/702E
TX-SR602/602E
TX-SR8260
Instruction Manual
Using the Remote Controller
with Other Components ......80
Thank you for purchasing an Onkyo AV Receiver.
Please read this manual thoroughly before making
any connections and plugging it in.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Receiver.
Troubleshooting......................90
Others.......................................94
Please retain this manual for future reference.
En
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 3 Tuesday, September 7, 2004 1:18 PM
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out permission of the copyright holder.
2. AC Fuse— The AC fuse inside the AV receiver is
not user-serviceable. If you cannot turn on the AV
receiver, contact your Onkyo dealer.
3. Care—Occasionally you should dust the AV
receiver all over with a soft cloth. For stubborn
stains, use a soft cloth dampened with a weak solu-
tion of mild detergent and water. Dry the AV
receiver immediately afterwards with a clean cloth.
Don’t use abrasive cloths, thinners, alcohol, or other
chemical solvents, because they may damage the
finish or remove the panel lettering.
For U.S. Models
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Section 820-40 of the NEC which
provides guidelines for proper grounding and, in partic-
ular, specifies that the cable ground shall be connected
to the grounding system of the building, as close to the
point of cable entry as practical.
FCC Information for User
CAUTION:
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
4. Power
WARNING
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
These limits are designed to provide reasonable protec-
tion against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a partic-
ular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of
the following measures:
AC outlet voltages vary from country to country. Make
sure that the voltage in your area meets the voltage
requirements printed on the AV receiver’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
For Worldwide model
The Worldwide model has a voltage selector for com-
patibility with power systems around the world. Before
you plug in this model, make sure that the voltage selec-
tor is set to the correct voltage for your area.
If it isn’t, use a small screwdriver to set it as appropriate.
For example, if the voltage in your area is 120 volts, set
the selector to “120V.” And if it’s between 220 and 230
volts, set it to “220-230V.”
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician
for help.
For Canadian model
NOTE: THIS CLASS B DIGITAL APPARATUS
For American and Australian models
COMPLIES WITH CANADIAN ICES-003.
Setting the [STANDBY/ON] switch to STANDBY does
not fully shutdown the AV receiver. If you do not intend
to use the AV receiver for an extended period, remove
the power cord from the wall outlet.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 4 Tuesday, September 7, 2004 1:18 PM
Supplied Accessories
Precautions—Continued
Make sure you have the following accessories:
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Remote controller & three batteries (AA/R6)
Blue:
Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
Speaker setup microphone
Indoor FM antenna
IMPORTANT
A 5 or 13 ampere fuse is fitted in this plug. Should the
fuse need to be replaced, please ensure that the replace-
ment fuse has a rating of 5 or 13 amperes and that it is
approved by ASTA or BSI to BS1362. Check for the
ASTA mark or the BSI mark on the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE
FOR THE SOCKET OUTLET IN YOUR HOME
THEN THE FUSE SHOULD BE REMOVED AND
THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMPERE SOCKET.
AM loop antenna
If in any doubt, consult a qualified electrician.
Power-plug adapter
For European Models
Only supplied in certain countries. Use this adapter if
your AC outlet does not match with the plug on the AV
receiver’s power cord. (Adapter varies from country to
country.)
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
1
2
3
corresponding
technical standards such as EN60065,
Speaker Cable
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
Speaker cable labels
I. MORI
ONKYO EUROPE ELECTRONICS GmbH
*
In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operation are the
same regardless of color.
The TX-SR702/702E, TX-SR602E, and Australian
TX-SR602 incorporate copyright protection technology
that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection tech-
nology must be authorized by Macrovision Corporation,
and is intended for home and other limited consumer
uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098;
4,907,093; 5,315,448; and 6,516,132.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 5 Tuesday, September 7, 2004 1:18 PM
Features
Audio/Video
TX-SR702/702E, TX-SR602/602E,
TX-SR8260
*4
• THX Surround EX
• THX Select certified
Amplifier
• VLSC (Vector Linear Shaping Circuitry) on all chan-
nels
• 7-channel amplifier
• Optimum Gain Volume Circuitry
• Zone 2 capability
• Re-EQ
• Pre outs for front L/R, center, surround L/R, surround
back L/R, and subwoofer
• 24-bit/192 kHz D/A converters
• WRAT (Wide Range Amplifier Technology)
• Color-coded speaker terminal posts
• Composite and S-Video to component video conver-
sion
• 7 digital inputs (5 optical, 2 coaxial), 2 digital outputs
(1 optical, 1 coaxial)
Audio/Video
*1
• Dolby Digital, Dolby Digital EX, Dolby Pro
THX Select
Logic IIx
Before any home theater component can be THX Select
certified, it must pass a rigorous series of quality and
performance tests. Only then can a product feature the
THX Select logo, which is your guarantee that the
Home Theater products you purchase will give you
superb performance for many years to come. THX
Select requirements define hundreds of parameters,
including power amplifier performance, and pre-ampli-
fier performance and operation for both digital and ana-
log domains. THX Select receivers also feature
proprietary THX technologies (e.g., THX Mode) which
accurately translate movie soundtracks for home the-
ater playback.
*2
• DTS , DTS-ES Discrete, DTS-ES Matrix, DTS
Neo:6, and DTS 96/24
*3
• Theater-Dimensional virtual surround mode
• Zone 2 line out
• Composite video to S-Video and S-Video to compos-
ite video conversion
• 3 component video inputs, 1 output
• 5 S-Video inputs, 3 outputs
FM/AM Tuner
• 40 AM/FM presets
• AM/FM auto tuning
• RDS—Radio Data System (Europe only)
TX-SR602/602E, TX-SR8260
Others
Amplifier
• Includes microphone for automatic speaker setup
• Easy-to-use onscreen setup menus
• 85 watts per channel into 8 ohms, 20 Hz to 20 kHz,
less than 0.08% total harmonic distortion (FTC rating)
• Preprogrammed remote controller for use with other
AV components
Audio/Video
• VLSC (Vector Linear Shaping Circuitry) on the front
left and right channels (European model only)
TX-SR702/702E
*5
• CinemaFILTER
Amplifier
• (Australian and European models only) Composite
and S-Video to component video conversion
• 100 watts per channel into 8 ohms, 20 Hz to 20 kHz,
less than 0.08% total harmonic distortion (FTC rating)
• Subwoofer pre out
• 6 digital inputs (4 optical, 2 coaxial), 1 digital optical
output (American model).
• 5 digital inputs (3 optical, 2 coaxial), 1 digital optical
output (other models)
*1. Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the double-D sym-
bol are trademarks of Dolby Laboratories.
*4. “THX” is a trademark or registered trademark of THX Ltd.
“Surround EX” is a trademark of Dolby Laboratories. Used
under authorization. All rights reserved.
*2. “DTS”, “DTS 96/24”, “DTS-ES”, and “Neo:6” are trademarks
of Digital Theater Systems, Inc.
*3. “Theater-Dimensional” is a trademark of Onkyo Corporation.
*5. “CinemaFILTER” is a trademark of Onkyo Corporation.
“Xantech” is a registered trademark of Xantech Corporation.
“Niles” is a registered trademark of Niles Audio Corporation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 6 Tuesday, September 7, 2004 1:18 PM
Table of Contents
Basic
Introduction
Important Safety Instructions..........................................................................................2
Precautions .......................................................................................................................3
Supplied Accessories.......................................................................................................4
Features.............................................................................................................................5
Table of Contents..............................................................................................................6
Front & Rear Panels..........................................................................................................8
Remote Controller...........................................................................................................13
About Home Theater.......................................................................................................20
Connecting the AV receiver
About AV Connections...................................................................................................21
ConnectingYour Speakers.............................................................................................22
Connecting Antenna.......................................................................................................24
ConnectingYour TV or Projector ...................................................................................27
Connecting AV components..........................................................................................28
Connecting Audio components.....................................................................................34
Connecting a Power Amplifier (TX-SR702/702E only).................................................37
Connecting
Components........................................................................................37
Connecting the Power Cords of Other Components...................................................38
Turning On the AV receiver............................................................................................38
First Time Setup
Automatic Speaker Setup...............................................................................................39
About the Onscreen Setup Menus ................................................................................41
Initial Setup......................................................................................................................42
Digital Input ...................................................................................................................42
Component Video Setup ...............................................................................................43
Minimum Speaker Impedance (not American models) .................................................44
TV Format Setup (not American models)......................................................................45
AM Frequency Step Setup (some models only)............................................................45
Speaker Setup.................................................................................................................46
Changing the TAPE/MD/CDR Display............................................................................52
Basic Operation
Selecting the Input Source.............................................................................................53
Setting the Display Brightness......................................................................................54
Muting the AV receiver ...................................................................................................54
Using the Sleep Timer.....................................................................................................54
Using Headphones .........................................................................................................54
Displaying Source Information......................................................................................55
Using the Tuner ...............................................................................................................56
Selecting Listening Modes.............................................................................................60
Listening mode table.....................................................................................................61
About the Listening Modes............................................................................................62
Others
Troubleshooting..............................................................................................................90
Specifications..................................................................................................................94
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 7 Tuesday, September 7, 2004 1:18 PM
Table of Contents—Continued
Advanced
Controlling Other Components
Entering a Remote Control Codes................................................................................ 80
Learning Commands from Another Remote Controller ............................................. 88
Using Macros.................................................................................................................. 89
Advanced
Features
Advanced Setup
Decoder Setup................................................................................................................ 68
Adjusting the Bass & Treble.......................................................................................... 70
Audio Adjust Functions................................................................................................. 70
Assigning Listening Modes to Input Sources ............................................................. 72
Setting Preferences........................................................................................................ 74
Changing the Remote Controller’s ID........................................................................... 75
Advanced
Features
Advanced Operation
Using the Late Night Function (Dolby Digital only) .................................................... 64
Using the Re-EQ Function (TX-SR702/702E only)....................................................... 64
Using the CinemaFILTER (TX-SR602/602E,TX-SR8260 only) .................................... 64
Adjusting Individual Speaker Levels............................................................................ 65
Using the DVD Analog Multichannel Input .................................................................. 65
Recording........................................................................................................................ 66
Advanced
Features
Zone 2
Connecting Zone 2......................................................................................................... 76
Setting the Powered Zone 2 .......................................................................................... 77
Using Zone 2................................................................................................................... 78
Using the Remote Control in Zone 2 ............................................................................ 79
Advanced
Features
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 8 Tuesday, September 7, 2004 1:18 PM
Front & Rear Panels
Front Panel
TX-SR702/702E
←Not American and Australian models
1
B
C45678 9J K LMN O PQ R S T
U V W X
Y
Z
TX-SR602/602E, TX-SR8260
←Not American and Australian models
1
B
C45678 9J K LMN O PQ R S T
U V W X
↑
Y
Z
Not American model
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 9 Tuesday, September 7, 2004 1:18 PM
Front & Rear Panels—Continued
For detailed information, see the pages in parentheses.
P DIMMER or RT/PTY/TP button (54, 59)
This button is used to adjust the display brightness.
A POWER switch (38)
American and Australian models don’t have this
switch.
On the European model, this is the RT/PTY/TP but-
ton, and it’s with RDS (Radio Data System). See
“Using RDS (European models only)” on page 58.
This is the main power switch. When set to OFF, the
AV receiver is completely shutdown. When set to
ON, it’s in Standby mode and the STANDBY indi-
cator lights up.
Q SETUP button
This button is used to access the onscreen setup
menus that appear on the connected TV.
Don’t turn on the power until you’ve completed,
and double checked all connections.
R Arrow/TUNING/PRESET & ENTER buttons
When the AM or FM input source is selected, the
TUNING [ ] [ ] buttons are used to tune the
tuner, and the PRESET [ ] [ ] buttons are used
to select radio presets (see page 57). When the
onscreen setup menus are used, they work as arrow
buttons and are used to select and set items. The
ENTER button is also used with the onscreen setup
menus.
B STANDBY/ON button (38)
This button is used to set the AV receiver to On or
Standby. For models with a POWER switch, this
button has no effect unless the POWER switch is set
to ON.
C STANDBY indicator (38)
This indicator lights up when the AV receiver is in
Standby mode, and it flashes while a signal is being
received from the remote controller.
S RETURN button
This button is used to return to the previously dis-
played onscreen setup menu.
D ZONE 2 indicator (78)
This indicator lights up when Zone 2 is selected.
T MASTER VOLUME control (53)
This control is used to adjust the volume of the AV
receiver to MIN, 1 through 99, or MAX
E Remote-control sensor (13)
This sensor receives control signals from the remote
controller.
U PURE AUDIO button & indicator (60)
The American TX-SR602 doesn’t have this button
and indicator.
F REC OUT button (66)
This button is used to select the input source to be
recorded.
This button is used to select the Pure Audio listen-
ing mode. The indicator lights up when that mode
selected.
G ZONE 2 button (78)
This button is used to select the input source for
Zone 2.
V PHONES jack (54)
This 1/4-inch phone jack is for connecting a stan-
dard pair of stereo headphones for private listening.
H LEVEL button (78)
This button is used to set the volume for Zone 2.
W SETUP MIC (39)
I Controller [ ] [ ] buttons (66, 78)
These buttons are used to select the input source to
be recorded via the REC OUTs, the input source for
Zone 2, and to set the volume for Zone 2.
The included speaker setup microphone is con-
nected here for automatic speaker setup.
X TONE, [–] & [+] buttons (70)
These buttons are used to adjust the bass and treble.
J STEREO button (60)
This button is used to select the Stereo listening
mode.
Y Input selector buttons (53)
These buttons are used to select from the following
input sources: MULTI CH, DVD, VIDEO 1,
VIDEO 2, VIDEO 3, VIDEO 4, TAPE, TUNER,
CD, or PHONO (TX-SR702/702E only).
K LISTENING MODE [ ] [ ] buttons (60)
These buttons are used to select the listening modes.
L DISPLAY button (55)
The [MULTI CH] button selects the DVD analog
multichannel input.
This button is used to display various information
about the currently selected input source.
Z VIDEO 4 INPUT (33, 67)
M Display
This input can be used to connect a camcorder,
games console, and so on. There are jacks for opti-
cal digital audio, S-Video, composite video, and
analog audio.
See “Display” on page 10.
N MEMORY button (57)
This button is used when storing or deleting radio
presets.
O TUNING MODE button (56)
This button is used to select the Auto or Manual tun-
ing mode.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 10 Tuesday, September 7, 2004 1:18 PM
Front & Rear Panels—Continued
Display
1 23
4
5
6
7
For detailed information, see the pages in parentheses.
AUTO: This indicator lights up when the Auto Tun-
ing mode is selected, and disappears when the Man-
ual Tuning mode is selected.
1MUTING indicator (54)
This indicator flashes while the AV receiver is
muted.
RDS (European model only): This indicator
lights up when the AV Receiver is tuned to a radio
station that supports RDS (Radio Data System).
2REC OUT indicator (66)
This indicator lights up when the REC OUT is
selected.
MEMORY: This indicator lights up when presetting
radio stations.
3ZONE 2 indicator (78)
This indicator lights up when Zone 2 is selected.
FM STEREO: This indicator lights up when the
AV receiver is tuned to a stereo FM station.
4Listening mode & format indicators
These indicators show the currently selected listen-
ing mode and the format of digital input signals.
6SLEEP indicator (54)
This indicator lights up when the Sleep function has
been set.
5Tuning indicators (56)
7Message area
TUNED: This indicator lights up when the AV
This area of the display shows various information
about the currently selected source.
receiver is tuned into a radio station.
Rear Panel
TX-SR702/702E
1 BCDE
H 9
K
L
M
J
6 G
Y
NOP Q R S T U V W X
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 11 Tuesday, September 7, 2004 1:18 PM
Front & Rear Panels—Continued
TX-SR602/602E, TX-SR8260
1 BCD
H 9
K
L
M
J
6 G
P Q R S T U V WX
Y
For detailed information, see the pages in parentheses.
A COMPONENT VIDEO IN 1, 2, 3 (28, 30, 32)
These component video inputs can be used to con-
nect AV components with component video outputs,
such as DVD players.
H MONITOR OUT (27)
The S-Video or composite video jack should be
connected to a video input on your TV or projector.
I OPTICAL DIGITAL (27, 28, 30, 32, 34, 35)
The number of digital outputs depends on where the
the AV receiver is purchased.
B AM ANTENNA (24)
These push terminals are for connecting an AM
antenna.
The optical digital audio inputs can be used to con-
nect CD and DVD players, and other components
with an optical digital audio output.
C COMPONENT VIDEO OUT (27)
This component video output can be used to con-
nect a TV or projector with a component video
input.
The optical output can be used connect a CD
recorder or other digital recorder with an optical
digital input.
D FM ANTENNA (24)
This jack is for connecting an FM antenna.
J COAXIAL DIGITAL (27, 28, 30, 32, 34, 35)
The coaxial digital audio inputs can be used to con-
nect CD and DVD players, and other components
with a coaxial digital audio output.
E RS232 (38)
The TX-SR602/602E, TX-SR8260, and American
and Australian TX-SR702 do not have this port.
The coaxial output can be used connect a CD
recorder or other digital recorder with a coaxial dig-
ital input.
This port is for connecting the AV receiver to home
automation equipment and external controllers.
F 12V TRIGGER OUT ZONE 2 (79)
The TX-SR602/602E and TX-SR8260 do not have a
coaxial output.
This output can be connected to the 12-volt trigger
input on a power amplifier in Zone 2. When Zone 2
is turned on, a 12-volt trigger signal is output.
K ZONE 2 SPEAKERS (76)
These terminal posts are for connecting speakers in
Zone 2.
G IR IN (79)
If you want to use the remote controller to control
the AV receiver from Zone 2, or if the AV receiver is
installed in a cabinet and the line of sight between
the AV receiver and the remote controller is
obstructed, a commercially available IR receiver
can be connected here.
L FRONT, CENTER, SURROUND &
SURROUND BACK SPEAKERS (23)
These terminal posts are for connecting your front,
center, surround, and surround back speakers.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 12 Tuesday, September 7, 2004 1:18 PM
Front & Rear Panels—Continued
M AC OUTLETS (38)
Y VOLTAGE SELECTOR (3)
These switched AC outlets can be used to supply
power to other AV components. The type of outlet
depends on the country in which you purchased
your AV receiver. Some models have a single outlet.
Certain models only.
This voltage selector provides compatibility with
power systems around the world.
N Grounding screw (TX-SR702/702E only) (36)
This screw is for connecting a turntable’s ground
wire.
O PHONO IN (TX-SR702/702E only) (36)
This analog input is for connecting a turntable.
P CD IN (34)
This analog audio input is for connecting a CD
player’s analog audio output.
Q TAPE IN/OUT (34)
This analog audio input and output are for connect-
ing a recorder with an analog audio input and output
(cassette, Mini Disc, etc).
R VIDEO 3 IN (27, 31)
Here you can connect a video source (VCR, set-top
box, etc). Input jacks include S-Video, composite
video, and analog audio.
S VIDEO 2 IN/OUT (30, 31)
Here you can connect a VCR. Input and output
jacks include S-Video, composite video, and analog
audio.
T VIDEO 1 IN/OUT (30, 31)
Here you can connect a VCR. Input and output
jacks include S-Video, composite video, and analog
audio.
U DVD IN (28, 29)
Here you can connect a DVD player. Input jacks
include S-Video, composite video, and analog
audio. You can connect a DVD player’s 2-channel
analog audio output or 5.1-channel analog audio
output.
V ZONE 2 LINE OUT (76)
This analog audio output can be connected to a line
input on an integrated amplifier in Zone 2.
W
REMOTE CONTROL (37)
This
(Remote Interactive) jack can be con-
nected to an
jack on another Onkyo AV compo-
nent. The AV receiver’s remote controller can then
be used to control that component. To use
, you
must make an analog audio connection (RCA)
between the AV receiver and the other AV compo-
nent, even if they are connected digitally.
X PRE OUT (37)
These analog audio outputs are for connecting a
separate power amplifier. Useful if you want to con-
nect a more powerful amplifier and use the AV
receiver as a preamp. The SUBWOOFER jack is for
connecting a powered subwoofer.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 13 Tuesday, September 7, 2004 1:18 PM
Remote Controller
Installing the Batteries
Using the Remote Controller
To use the remote controller, point it at the AV receiver’s
remote control sensor, as shown below.
To open the battery compartment, press
the small hollow and slide off the cover.
1
Remote control sensor
30˚
30˚
Insert the three supplied batteries (AA/R6)
2
in accordance with the polarity diagram
inside the battery compartment.
Notes:
• The remote controller may not work reliably if the AV
receiver is subjected to bright light, such as direct sun-
light or inverter-type fluorescent lights. Keep this in
mind when installing.
• If another remote controller of the same type is used in
the same room, or the AV receiver is installed close to
equipment that uses infrared rays, the remote control-
ler may not work reliably.
Put the cover onto the remote controller
and slide it shut.
3
• Don’t put anything, such as a book, on the remote con-
troller, because the buttons may be pressed inadvert-
ently, thereby draining the batteries.
• The remote controller may not work reliably if the AV
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
• The remote controller will not work if there’s an obsta-
cle between it and the AV receiver’s remote control
sensor.
Notes:
• The batteries should last for about six months,
although this will vary with usage.
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as possi-
ble to prevent damage from leakage or corrosion.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 14 Tuesday, September 7, 2004 1:18 PM
Remote Controller—Continued
In addition to controlling the AV receiver, the remote
controller has several operating modes for controlling
your other AV components, including Onkyo compo-
Receiver Mode
Receiver mode is used to control the AV receiver. To
select Receiver mode, press the [RECEIVER] REMOTE
MODE button.
nents connected via
. Modes are selected by using
the remote controller’s REMOTE MODE buttons.
For detailed information, see the pages in parentheses.
Some of the functions described in this manual may not
work as expected with other components.
RC-588M
Remote
indicator
This indicator
lights up
when the
A
B
remote con-
troller is
transmitting
commands.
3
4
T
N
RECEIVER
5
O
6
7
P
8
9
J
Q
R
K
L
M
S
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 15 Tuesday, September 7, 2004 1:18 PM
Remote Controller—Continued
PURE A button (RC-591M & RC-588M only)
This button is used to select the Pure Audio listen-
ing mode.
RC-591M, RC-590M
DIRECT button
This button is used to select the Direct listening
mode.
No “PURE A” on
RC-590M
[
DSP] & [DSP ] buttons
These buttons are used to select the Onkyo original
DSP (digital signal processor) listening modes.
U
L TEST TONE, CH SEL, LEVEL- & LEVEL+
buttons (50)
These buttons are used to adjust the level of each
speaker individually. The [LEVEL–] & [LEVEL+]
buttons are also used to adjust the volume in Zone 2.
A STANDBY button (38)
This button is used to set the AV receiver to
Standby.
M L NIGHT button (64)
This button is used to set the Late Night function.
N MACRO buttons (89)
B ON button (38)
These buttons are used with the Macro function.
This button is used to turn on the AV receiver.
C INPUT SELECTOR buttons (53)
These buttons are used to select the input source.
Only the RC-588M has a [PHONO] button.
O SLEEP button (54)
This button is used to set the Sleep function.
P VOL button (53)
D MULTI CH button (65)
This button is used to select the DVD analog multi-
channel input.
This button is used to adjust the volume of the AV
receiver.
Q SETUP button
E REMOTE MODE buttons
These buttons are used to select the remote control-
ler modes.
This button is used to access the onscreen setup
menus that appear on the connected TV.
R MUTING button (54)
F DIMMER button (54)
This button is used to mute the AV receiver.
This button is used to adjust the display brightness.
S Re-EQ button (RC-588M only) (64)
This button is used to turn the Re-EQ function on
and off.
G Arrow [ ]/[ ]/[ ]/[ ] & ENTER buttons
These buttons are used to select items on the
onscreen setup menus.
T LIGHT button (RC-588M only)
This button is used to turn on or off the remote con-
troller’s illuminated buttons.
H CH +/– button (57)
This button is used to select radio presets.
I RETURN button
U CINE FLTR button (RC-590M & RC-591M
This button is used to return to the previously dis-
played onscreen setup menu.
only) (64)
This button is used to set the CinemaFILTER func-
J DISPLAY button (55, 57)
tion.
This button is used to display various information
about the currently selected input source.
K Listening mode buttons (60)
SURR button
This button is used to select the Dolby Digital, Pro
Logic IIx, Neo:6, DTS and other listening modes.
ALL ST button
This button is used to select the All Ch Stereo listen-
ing mode.
THX button (RC-588M only)
This button is used to select the THX listening
modes.
STEREO button
This button is used to select the Stereo listening
mode.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 16 Tuesday, September 7, 2004 1:18 PM
Remote Controller—Continued
DVD Mode
DVD mode is used to control an Onkyo DVD player con-
nected to the AV receiver via
.
To set the remote controller to DVD mode, press the
[DVD] REMOTE MODE button.
1
2
A
B
A STANDBY button
This button is used to set the DVD player to
Standby.
B ON button
This button is used to turn on the DVD player and to
set it to Standby.
3
C Number buttons
These buttons are used to enter title, chapter, and
track numbers, and to enter times for locating spe-
cific points in time.
Q8
D TOP MENU button
DVD
CD
This button is used to select a DVD’s top menu.
E Arrow [ ]/[ ]/[ ]/[ ] & ENTER buttons
These buttons are used to navigate DVD menus and
the DVD player’s onscreen setup menus.
R
4
5
F DISC +/– button
This button selects discs on a DVD changer.
G RETURN/EXIT button
This button is used to exit the DVD player’s
onscreen setup menu.
9
S
T
3
6
7
8
H DISPLAY button
4
5
U0
This button is used to display information about the
current disc, title, chapter, or track on the DVD
player’s display, including the elapsed time, remain-
ing time, total time, and so on.
9
A
B
I Playback buttons
V
W
X
Y
J
From left to right: Previous, Play, Next, Fast
Reverse, Pause, Stop, and Fast Forward.
K
L
M
N
J Step & Slow [ ]/[ ] buttons
These buttons are used for frame-by-frame playback
and slow-motion playback.
6
7
Z
K AUDIO button
O
P
This button is used to select foreign language
soundtracks and audio formats (e.g., Dolby Digital
or DTS).
L SUBTITLE button
This button is used to select subtitles.
Round numbers are for DVD mode.
Square numbers are for CD mode.
M REPEAT button
This button is used to set the repeat playback func-
tions.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 17 Tuesday, September 7, 2004 1:18 PM
Remote Controller—Continued
N A-B button
CD Mode
This button is used to set the A–B repeat playback
function.
CD mode is used to control an Onkyo CD player con-
nected to the AV receiver via
.
O OPEN/CLOSE [ ] button
To set the remote controller to CD mode, press the
[CD] REMOTE MODE button.
This button is used to open and close the disc tray.
P VIDEO OFF button
1ON button
This button is used to turn off the internal video cir-
cuitry, eliminating any possibility of interference.
This button is used to set the CD player to On or
Standby.
Q CLEAR button
2Number buttons
This button is used to cancel functions and to clear
entered numbers.
These buttons are used to enter track numbers and
to enter times for locating specific points in time.
R MENU button
This button is used to display a DVD’s menu.
3DISC button
This button is used to select discs on a CD changer.
S VOL button
This button is used to adjust the volume of the AV
receiver.
4DISPLAY button
This button is used to display information about the
current disc or track on the CD player’s display,
including the elapsed time, remaining time, total
time, and so on.
T SETUP/GUIDE button
This button is used to access the DVD player’s
onscreen setup menus.
5Playback buttons
U MUTING button
From left to right: Previous, Play, Next, Fast
Reverse, Pause, Stop, and Fast Forward.
This button is used to mute the AV receiver.
V RANDOM button
This button is used with the random playback func- 6REPEAT button
tion.
This button is used to set the repeat playback func-
tions.
W ANGLE button
This button is used to select camera angles.
7OPEN/CLOSE [ ] button
This button is used to open and close the disc tray.
X LAST M button
This button is used with the last memory function,
which allows you to resume DVD playback from
where you left off.
8CLEAR button
This button is used to cancel functions and to clear
entered numbers.
Y SEARCH button
9VOL button
This button is used to search for titles, chapters,
tracks, and specific points in time.
This button is used to adjust the volume of the AV
receiver.
Z MEMORY button
0MUTING button
This button is used with the memory playback func-
tion, which allows you to create a custom playlist of
titles, chapters, or tracks.
This button is used to mute the AV receiver.
ARANDOM button
This button is used with the random playback func-
tion.
BMEMORY button
This button is used with the memory playback func-
tion, which allows you to create a custom playlist of
tracks.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 18 Tuesday, September 7, 2004 1:18 PM
Remote Controller—Continued
MD/CDR Mode
MD/CDR mode is used to control an Onkyo MiniDisc
recorder or CD recorder connected to the AV receiver via
.
To select MD/CDR mode, press the [MD/CDR]
REMOTE MODE button.
By default, this button is set to control a MiniDisc
recorder. To control a CD recorder, it must be set to CD
(see page 80).
1
A ON button
This button is used to set the MD recorder or CD
recorder to On or Standby.
2
B Number buttons
These buttons are used to enter track numbers and
to enter times for locating specific points in time.
J
C DISPLAY button
This button is used to display information about the
current disc or track on the MD recorder or CD
recorder’s display, including the elapsed time,
remaining time, total time, and so on.
TAPE
MD/CDR
D Play [ ] button
This button is used to start playback.
E Previous & Next [
The Previous [ ] button is used to select the pre-
vious track. During playback it selects the begin-
]/[
] buttons
5
K
ning of the current track. The Next [
used to select the next track.
] button is
3
L6
F Pause [ ] button
4
5
1
2
This button is used to pause playback.
M
7
8
G REC [ ] button
6
7
N
O
3
4
This button is used to start recording.
H REPEAT button
This button is used to set the repeat playback func-
tions.
P
8
9
I OPEN/CLOSE [ ] button
This button is used to eject a MiniDisc or to open
and close the CD recorder’s disc tray.
J CLEAR button
This button is used to cancel functions and to clear
entered numbers.
K VOL button
This button is used to adjust the volume of the AV
receiver.
Round numbers are for MD/CDR mode.
Square numbers are for TAPE mode.
L MUTING button
This button is used to mute the AV receiver.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 19 Tuesday, September 7, 2004 1:18 PM
Remote Controller—Continued
M FR & FF [ ]/[ ] buttons
The FR [ ] button is used to start fast reverse. The
FF [ ] button is used to start fast forward.
N Stop [ ] button
This button is used to stop playback.
O RANDOM button
This button is used with the random playback func-
tion.
P MEMORY button
This button is used with the memory playback func-
tion, which allows you to create a custom playlist of
tracks.
TAPE Mode
TAPE mode is used to control an Onkyo cassette
recorder connected to the AV receiver via
.
To set the remote controller to TAPE mode, press the
[TAPE] REMOTE MODE button.
For double cassette decks, only Deck B can be con-
trolled.
1Play [ ] button
This button is used to start playback.
2Previous & Next [
The Previous [ ] button is used to select the pre-
vious track. During playback it selects the begin-
]/[
] buttons
ning of the current track. The Next [
used to select the next track.
] button is
The Previous and Next [
]/[
] buttons may not
work properly with some cassette tapes depending
on how they were recorded.
3Reverse Play [ ] button
This button is used to start reverse playback.
4REC [ ] button
This button is used to start recording.
5VOL button
This button is used to adjust the volume of the AV
receiver.
6MUTING button
This button is used to mute the AV receiver.
7Rewind & FF [ ]/[ ] buttons
The Rewind [ ] button is used to start rewind. The
FF [ ] button is used to start fast forward.
8Stop [ ] button
This button is used to stop playback.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 20 Tuesday, September 7, 2004 1:18 PM
About Home Theater
Enjoying Home Theater
Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your
own home—just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With
analog and digital TV you can enjoy Dolby Pro Logic IIx or Onkyo’s own DSP surround listening modes.
With the TX-SR702/702E you can enjoy DVDs that feature THX Surround EX (THX-certified THX speaker system
recommended).
Front left and right speakers
These output the overall sound. Their role in a home theater is to provide a solid
anchor for the sound image.They should be positioned facing the listener at about
Surround left and right
speakers
ear level, and equidistant from theTV.Angle them inward so as to create a triangle,
These speakers are used for
with the listener at the apex.
precise sound positioning and
to add realistic ambience.
Position them at the sides of
the listener, or slightly behind,
about 2–3 feet (60–100 cm)
above ear level. Ideally they
should be equidistant from the
listener.
Center speaker
This speaker enhances the front left
and right speakers, making sound
movements distinct and providing a
full sound image. In movies it’s used
mainly for dialog.
Position it close to yourTV (preferably
on top) facing forward at about ear
level, or at the same height as the
front left and right speakers.
Subwoofer
The subwoofer handles the bass sounds of
the LFE (Low-Frequency Effects) channel.
The volume and quality of the bass output
from your subwoofer will depend on its posi-
tion, the shape of your listening room, and
your listening position. In general, a good
bass sound can be obtained by installing the
subwoofer in a front corner, or at one-third
the width of the wall, as shown.
Surround back left and right speakers
These speakers are necessary to enjoy Dolby Digital EX, DTS-ES
Matrix, DTS-ES Discrete, andTHX Surround EX (TX-SR702/702E only).
They enhance the realism of surround sound and improve sound local-
ization behind the listener. Position them behind the listener about 2–
3 feet (60–100 cm) above ear level.
Tip: To find the best position for your sub-
woofer, while playing a movie or some
music with good bass, experiment by plac-
ing your subwoofer at various positions
within the room, and choose the one that
provides the most satisfying results.
For the TX-SR702/702E, THX recommends
that they be placed equidistant from the lis-
tener, creating a triangle, and that the angle
at the apex of the triangle is about 60
degrees. Make sure that the listening posi-
tion is within the range of the speakers.
60˚
Surround
back left
speaker
Surround
back right
speaker
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 21 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver
AV Connection Color Coding
About AV Connections
RCA-type AV connections are usually color coded: red,
white, and yellow. Use red plugs to connect right-
channel audio inputs and outputs (typically labeled “R”).
Use white plugs to connect left-channel audio inputs and
outputs (typically labeled “L”). And use yellow plugs to
connect composite video inputs and outputs.
• Before making any AV connections, read the manuals
supplied with your other AV components.
• Don’t connect the power cord until you’ve completed
and double-checked all AV connections.
Optical Digital Jacks
The AV receiver’s optical digital jacks have shutter-type
covers that open when an optical plug is inserted and
close when it’s removed. Push plugs in all the way.
Analog audio
Right (red)
Left (white)
Right (red)
Left (white)
Composite video
(Yellow)
(Yellow)
Right!
Caution: To prevent shutter damage, hold the optical
plug straight when inserting and removing.
• Push plugs in all the way to make
good connections (loose connec-
tions can cause noise or malfunc-
tions).
• To prevent interference, keep
audio and video cables away from
power cords and speaker cables.
Wrong!
AV Cables & Jacks
Video
Cable
Jack
Description
P
R
B
P
P
R
B
Component video separates the luminance (Y) and
color difference signals (PR, PB), providing the best
picture quality. (Some TV manufacturers label their
component video sockets slightly differently.)
Y
Component
video cable
P
Y
PB
Y
PR
S-Video separates the luminance and color signals
and provides better picture quality than composite
video.
S
S-Video cable
Composite video is commonly used on TVs, VCRs,
and other video equipment. Use only dedicated
composite video cables.
Composite
video cable
V
Audio
Cable
Jack
Description
Offers the best sound quality and allows you to
enjoy surround sound (e.g., Dolby Digital, DTS).
The audio quality is the same as for coaxial.
OPTICAL
Optical digital
audio cable
Offers the best sound quality and allows you to
enjoy surround sound (e.g., Dolby Digital, DTS).
The audio quality is the same as for optical.
COAXIAL
Coaxial digital
audio cable
This cable carries analog audio. It’s the most
common connection format for analog audio, and
can be found on virtually all AV components.
L
Analog audio
cable (RCA)
R
This cable carries multichannel analog audio and
it’s typically used to connect DVD players with a
5.1-channel analog audio output. Several standard
analog audio cables can be used instead of a multi-
channel cable.
Multichannel
analog audio
cable (RCA)
Note: The AV receiver does not support SCART plugs.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 22 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
Connecting a Powered Subwoofer
ConnectingYour Speakers
Using a suitable cable, connect the AV receiver’s SUB-
WOOFER PRE OUT to an input on your powered sub-
woofer, as shown. If your subwoofer is unpowered and
you’re using an external amplifier, connect the SUB-
WOOFER PRE OUT to an input on the amp.
Speaker Configuration
For the best surround-sound experience, you should con-
nect seven speakers and a powered subwoofer.
The following table indicates the channels you should
use depending on the number of speakers that you have.
Number of speakers:
Front left
2
3
4
5
6
7
Powered
subwoofer
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Front right
Center
LINE INPUT
Surround left
✓
✓
Surround right
Surround back
Surround back left*
Surround back right*
LINE INPUT
✓
✓
*If you’re using only one surround back speaker, connect it to
the left (L) SURROUND BACK SPEAKERS terminals.
Attaching the Speaker Labels
No matter how many speakers you use, a powered sub-
woofer is recommended for a really powerful and solid
bass.
To get the best from your surround-sound system, you
need to set the speaker settings by using the supplied
setup microphone (see page 39).
The AV receiver’s positive (+) speaker terminals are
color-coded for ease of identification. (The negative (–)
speaker terminals are all black.)
Speaker terminal
Front left, Zone 2 left
Front right, Zone 2 right
Center
Color
White
Red
Using Dipole Speakers
Green
Blue
You can use dipole speakers for the surround left and
right and surround back left and right speakers. Dipole
speakers output the same sound in two directions.
Dipole speakers typically have an arrow printed on them
to indicate how they should be positioned. The surround
left and right dipole speakers should be positioned so that
their arrows point toward the TV/screen, while the sur-
round left and right dipolar speakers should be positioned
so that their arrows point toward each other, as shown.
Surround left
Surround right
Gray
Brown
Tan
Surround back left
Surround back right
The supplied speaker labels are also color-coded and you
should attach them to the positive (+) side of each
speaker cable in accordance with the above table.All you
need to do then is to match the color of each label to the
corresponding speaker terminal.
Normal speakers
Dipole speakers
1
TV/screen
TV/screen
1
4
2
3
4
2
3
5
6
5
6
7
8
7
8
1. Subwoofer
2. Front left speaker
3. Center speaker
6. Surround right speaker
7. Surround back left
speaker
4. Front right speaker
5. Surround left speaker
8. Surround back right
speaker
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 23 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
Speaker Connection Precautions
Connecting the Speaker Cables
Read the following before connecting your speakers:
• American model only: Only connect speakers with
an impedance of 6 ohms or higher. If you use speakers
with a lower impedance, and use the amplifier at high
volume levels for a long period of time, the built-in
protection circuit may be activated.
• Other models:You can connect speakers with an
impedance of between 4 and 16 ohms. If the imped-
ance of any of the connected speakers is 4 ohms or
more, but less than 6 ohms, be sure to set the Mini-
mum Speaker Impedance to “4 ohms” (see page 44).
If you use speakers with a lower impedance, and use
the amplifier at high volume levels for a long period of
time, the built-in protection circuit may be activated.
• Disconnect the power cord from the wall outlet before
making any connections.
Strip about 5/8" (15 mm)
of insulation from the
ends of the speaker
cables, and twist the bare
wires tightly, as shown.
5/8" (15 mm)
1
Unscrew the terminal.
2
Fully insert the bare
wires.
3
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals to only positive
(+) terminals, and negative (–) terminals to only nega-
tive (–) terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
Screw the terminal tight.
4
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the
positive and negative wires.
Doing so may damage the AV
receiver.
• Don’t connect more than one
cable to each speaker termi-
The following illustration shows which speaker should
be connected to each pair of terminals.
If you’re using only one surround back speaker, connect
it to the left (L) SURROUND BACK SPEAKERS termi-
nals.
Surround
back left
speaker
Surround
left
speaker
Surround
back right
speaker
nal. Doing so may damage the
AV receiver.
• Don’t connect one speaker to several terminals.
Surround
right
speaker
Front left
speaker
Front right
speaker
Center
speaker
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 24 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead (see page 25).
Connecting Antenna
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The AV receiver won’t pick up any radio signals without
any antenna connected, so you must connect the antenna
to use the tuner.
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
AM antenna push terminals
FM antenna connector
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
1
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
Connecting the Indoor FM Antenna
2
The supplied indoor FM antenna is for indoor use only.
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around).
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
Attach the FM antenna, as shown.
1
■ American Model
Insert the plug fully
into the jack.
■ Other Models
Push
Insert wire
Release
Insert the plug fully
into the jack.
Once your AV receiver is ready for use, you’ll
need to tune into an FM radio station and adjust
the position of the FM antenna to achieve the best
possible reception.
Once your AV receiver is ready for use, you’ll
need to tune into an AM radio station and adjust
the position of theAM antenna to achieve the best
possible reception.
Keep the antenna as far away as possible from
your AV receiver, TV, speaker cables, and power
cords.
Use thumbtacks or something similar to
fix the FM antenna into position.
2
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commer-
cially available outdoor AM antenna (see page 25).
Thumbtacks, etc.
Caution: Be careful that you don’t injure yourself
when using thumbtacks.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 25 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead.
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoorAM antenna can be used in
addition to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
AM loop antenna
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
Outdoor AM antennas work best when installed outside
horizontally, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from possi-
ble noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock haz-
ards.
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If cir-
cumstances demand it, use a TV/FM antenna splitter, as
shown.
TV/FM antenna splitter
To AV receiver
To TV (or VCR)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 26 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
Connecting Both Audio & Video
By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you
can select both the audio and video simultaneously simply by selecting the appropriate input source on the AV receiver.
: Signal Flow
Video
Audio
Video
Audio
TV, projector,
etc.
DVD player, etc.
Speakers (see page 23 for connection infor-
mation)
Which Connections Should I Use?
The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format
you choose will depend on the formats supported by your other components. Use the following sections as a guide.
For video components, you must make two connections—one for audio, one for video.
Video Connection Formats
Audio Connection Formats
Video equipment can be connected to the AV receiver by
using any one of the following video connection formats:
composite video, S-Video, or component video, the
latter offering the best picture quality.
A video signal connected to a V or S IN jack will be con-
verted—composite video to S-Video or S-Video to com-
posite video—but only for the MONITOR OUT jacks,
not the VIDEO 1 and VIDEO 2 OUT V and S jacks.
Note: The TX-SR702/702E, TX-SR602E, and Austra-
lian TX-SR602 can be set to upconvert composite video
and S-Video input signals and output them from the
COMPONENT VIDEO OUT (see page 43).
Audio equipment can be connected to the AV receiver by
using any of the following audio connection formats:
analog, optical, coaxial, or multichannel.
When choosing a connection format, bear in mind that
the AV receiver doesn’t convert between them. For
example, audio signals connected to an OPTICAL or
COAXIAL input are not output by the analog TAPE
OUT.
DVD player,
etc.
Optical
Coaxial
Analog
Multi-
channel
Output
IN
DVD player,
etc.
Analog
Analog
Coaxial
Optical
Optical
Multi-
channel
AV Receiver
Composite
Composite
S-Video
S-Video
Component
Component
Output
IN
Coaxial *
Only front
left and
right
OUT
Input
AV Receiver
page 43 *
Coaxial
Analog
Optical
Component
MDrecorder,
etc.
S-Video
S-Video
Composite
Composite
MONITOR OUT
*TX-SR702/702E only
Input
Component
TV, pro-
jector,
etc.
*TX-SR702/702E, 602E and
Australian TX-SR602 only
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 27 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
ConnectingYour TV or Projector
Monitor Out
Audio Connections
These connections will allow you to listen to audio from
your TV via the AV receiver.
If your TV doesn’t have an audio output, connect the AV
receiver to your VCR and use its tuner (see page 30).
■ Using Composite Video
Use a composite video cable to connect the AV receiver’s
V MONITOR OUT jack to a composite video input on
your TV, as shown.
■ Using Coaxial or Optical Connections
If you connect to a digital audio input, you’ll need to
assign it (see page 42).
MONITOR
OUT
V
• Use an optical digital audio cable to connect one of the
AV receiver’s OPTICAL DIGITAL IN jacks to an
optical output on your TV, as shown.
OR
• Use a coaxial digital audio cable to connect one of the
AV receiver’s COAXIAL DIGITAL IN jacks to a
coaxial output on your TV, as shown.
TV, projector,
etc.
VIDEO IN
COAXIAL
IN
■ Using S-Video
Use an S-Video cable to connect the AV receiver’s
S MONITOR OUT jack to an S-Video input on your TV,
as shown.
IN
OPTICAL
Connect one or the
other
MONITOR
OUT
S
TV, projector,
etc.
DIGITAL OUT
COAXIAL
DIGITAL OUT
OPTICAL
TV, projector,
etc.
■ Using Analog Connections
If your TV doesn’t have a digital audio output, or you
want to record from it, you’ll need to make the following
analog audio connection.
S VIDEO IN
Use an analog audio cable to connect the AV receiver’s
VIDEO 3 IN L/R jacks to an analog audio output on your
TV, as shown.
■ Using Component Video
Use a component video cable to connect the AV
receiver’s COMPONENT VIDEO OUT jacks to a com-
ponent video input on your TV, as shown.
COMPONENT VIDEO
Y
IN
PB
PR
VIDEO 3
AUDIO
OUTPUT
TV, projector,
etc.
TV, projector,
etc.
L
Y
PB
PR
R
COMPONENT
VIDEO IN
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 28 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
Audio Connections
Connecting a DVD Player
■ Using Coaxial or Optical Connections
• Use an optical digital audio cable to connect one of the
AV receiver’s OPTICAL DIGITAL IN jacks to the
optical output on your DVD player, as shown.
OR
• Use a coaxial digital audio cable to connect one of the
AV receiver’s COAXIAL DIGITAL IN jacks to the
coaxial output on your DVD player, as shown.
Video Connections
You only need to use one of the following connection
methods.
■ Using Composite Video
Use a composite video cable to connect the AV receiver’s
V DVD IN jack to the composite video output on your
DVD player, as shown.
DVD
IN
DIGITAL
COAXIAL
IN
IN1
OPTICAL
Connect one or the other
VIDEO OUT
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
DVD player
■ Using S-Video
Use an S-Video cable to connect the AV receiver’s
S DVD IN jack to the S-Video output on your DVD
player, as shown.
DVD player
DVD
IN
Initially, the OPTICAL IN1 jack is assigned to the DVD
input source. If you connect your DVD player to a dif-
ferent digital input, you’ll need to reassign the DVD
input source (see page 42).
■ Using Analog Connections
Even if your DVD player is connected digitally (optical
or coaxial), to use
, or to record audio from your
DVD player, you’ll need to make an analog connection
as well.
Use an analog audio cable to connect the AV receiver’s
DVD IN L/R jacks to the analog audio output on your
DVD player, as shown.
If your DVD player has stereo (L/R) and multichannel
outputs, be sure to use the left and right outputs.
S VIDEO OUT
DVD player
■ Using Component Video
Use a component video cable to connect the AV
receiver’s COMPONENT VIDEO IN1 jacks to the com-
ponent video output on your DVD player, as shown.
• Your TV must also be connected via component video.
FRONT
L
COMPONENT VIDEO
IN1
R
Y
DVD
PB
PR
COMPONENT
VIDEO OUT
R
L
AUDIO
OUTPUT
Y
PB
PR
DVD player
DVD player
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 29 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
■ Using a Multichannel Connection
If your DVD player supports multichannel audio formats
such as DVD-Audio, and it has a 5.1-channel analog
audio output, you can enjoy DVD-Audio playback.
Use a multichannel analog audio cable to connect the AV
receiver’s DVD IN FRONT L/R, CENTER, SURR L/R,
and SUBWOOFER jacks to the 5.1-channel analog
audio output on your DVD player, as shown. Alterna-
tively, use several analog audio cables.
DVD player
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 30 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
Connecting a VCR for Playback
Connecting a D-VHS VCR for Playback
This section shows how to connect a VCR for playback
so that you can watch videos via the AV receiver.
Video Connections
If you connect to a component video input, you must
assign it (see page 43).
Video Connections
Use a component video cable to connect the AV
receiver’s COMPONENT VIDEO IN2 or 3 jacks to a
component video output on your D-VHS VCR, as
shown.
• Use an S-Video cable to connect the AV receiver’s
S VIDEO 1 IN jack to a S-Video output on yourVCR,
as shown.
OR
• Use a composite video cable to connect the AV
receiver’s V VIDEO 1 IN jack to a composite video
output on your VCR, as shown.
Your TV must also be connected via component video.
COMPONENT VIDEO
IN
Y
An S-Video connection provides better picture quality
than a composite video connection.
PB
PR
Audio Connections
• Use an analog audio cable to connect the AV receiver’s
VIDEO 1 IN L/R jacks to an analog audio output on
your VCR, as shown.
COMPONENT
VIDEO OUT
Y
VIDEO 1
IN
PB
PR
D-VHS VCR
IN
L
Audio Connections
If you connect to a digital audio input, you'll need to
assign it (see page 42).
R
• Use an optical digital audio cable to connect one of the
AV receiver’s OPTICAL DIGITAL IN jacks to an
optical output on your D-VHS VCR, as shown.
OR
Connect one
or the other
• Use a coaxial digital audio cable to connect one of the
AV receiver’s COAXIAL DIGITAL IN jacks to a
coaxial output on your D-VHS VCR, as shown.
R
L
AUDIO
OUTPUT
VIDEO OUT
S VIDEO OUT
VCR
DIGITAL
IN
COAXIAL
OPTICAL
IN
Connect one or the other
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
D-VHS VCR
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 31 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
Connecting a VCR for Recording
VCR (recording)
This section explains how to connect a VCR for
recording from a TV or another VCR.
R
L
R
L
AUDIO
INPUT
AUDIO
OUTPUT
Video Connections
• Use an S-Video cable to connect the AV receiver’s
S VIDEO 1 OUT jack to an S-Video input on the
recordingVCR. Use another S-Video cable to connect
the AV receiver’s S VIDEO 3 IN jack to an S-Video
output on your TV or playback VCR, as shown.
S VIDEO IN
VIDEO OUT
VIDEO IN
S VIDEO OUT
OR
• Use a composite video cable to connect the AV
receiver’s V VIDEO 1 OUT jack to a composite video
input on the recording VCR. Use another composite
video cable to connect the AV receiver’s V VIDEO 3
IN jack to a composite video output on your TV or
playback VCR, as shown.
Connect one or
the other
VIDEO 1
OUT
IN
Audio Connections
• Use an analog audio cable to connect the AV receiver’s
VIDEO 1 OUT L/R jacks to an audio input on the
recording VCR.
OUT
IN
• Use an analog audio cable to connect the AV receiver’s
VIDEO 3 IN L/R jacks to an audio output on your TV
or playback VCR.
VIDEO 3
IN
Playback from the Recording VCR
To play back a video in the recording VCR via the AV
receiver:
• Use an S-Video cable to connect the AV receiver’s S
IN
VIDEO 1 IN jack to an S-Video output on the record-
L
ing VCR.
OR
R
• Use a composite video cable to connect the AV
receiver’s V VIDEO 1 IN jack to a composite video
output on the recordingVCR.And use an analog audio
cable to connect the AV receiver’s VIDEO 1 IN L/R
jacks to an audio output on the recording VCR.
Connect one
or the other
R
L
AUDIO
OUTPUT
S VIDEO
OUT
Notes:
• The AV receiver must be turned on for recording.
Recording is not possible while it’s in Standby mode.
VIDEO
OUT
:
:
For recording
For playback
• If you want to record directly from your TV or play-
back VCR to the recording VCR without going
through the AV receiver, connect the TV/VCR’s audio
and video outputs directly to the recording VCR’s
audio and video inputs. See the manuals supplied with
your TV and VCR for details.
or VCR, etc.
TV
• Video signals connected to composite video inputs
can only be recorded via composite video outputs. If
your TV/VCR is connected to a composite video
input, the recording VCR must be connected to a com-
posite video output. Similarly, video signals con-
nected to S-Video inputs can only be recorded via
S-Video outputs. If your TV/VCR is connected to an
S-Video input, the recording VCR must be connected
to an S-Video output.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 32 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
■ Using Component Video
If you connect to a component video input, you must
assign it (see page 43).
Use a component video cable to connect the AV
receiver’s COMPONENT VIDEO IN 2 or IN 3 jack to a
component video output on your video source, as shown.
Connecting Other Video Sources—
Satellite, Cable, Set-top box, LD
Player, etc.
Video Connections
You only need to use one of the following connection
methods.
COMPONENT VIDEO
IN
Y
■ Using Composite Video
Use a composite video cable to connect the AV receiver’s
V VIDEO 3 IN jack to a composite video output on your
video source, as shown.
PB
PR
COMPONENT
VIDEO OUT
VIDEO 3
IN
Y
PB
PR
Satellite, cable, set-top
box, LD player, etc.
Audio Connections
■ Using Optical or Coaxial Connections
If you connect to a digital audio input, you’ll need to
assign it (see page 42).
• Use an optical digital audio cable to connect one of the
AV receiver’s OPTICAL DIGITAL IN jacks to an
optical output on your video source, as shown.
OR
VIDEO OUT
Satellite, cable, set-top
box, LD player, etc.
■ Using S-Video
• Use a coaxial digital audio cable to connect one of the
AV receiver’s COAXIAL DIGITAL IN jacks to a
coaxial output on your video source, as shown.
Use an S-Video cable to connect the AV receiver’s
S VIDEO 3 IN jack to an S-Video output on your video
source, as shown.
VIDEO 3
IN
DIGITAL
COAXIAL
IN
IN
OPTICAL
Connect one or the other
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
S VIDEO OUT
Satellite, cable, set-top
box, LD player, etc.
Satellite, cable, set-top box, LD player, etc.
Notes:
• To connect the AV receiver to an LD player’sAC-3RF
output, you need a commercially available demodula-
tor.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 33 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
■ Using Analog Connections
■ Using S-Video
If your video source doesn’t have a digital audio output,
or you want to record from it, you’ll need to make the
following analog audio connection.
Use an S-Video cable to connect the AV receiver’s
VIDEO 4 INPUT S VIDEO jack to the S-Video output
on your camcorder, games console, etc., as shown.
Use an analog audio cable to connect the AV receiver’s
VIDEO 3 IN L/R jacks to the analog audio output on
your video source, as shown.
IN
L
R
VIDEO 3
S VIDEO OUT
S VIDEO
Camcorder,
games console, etc.
Audio Connections
R
L
AUDIO
OUTPUT
Use an analog audio cable to connect the AV receiver’s
VIDEO 4 INPUT AUDIO L/R jacks to the analog audio
output on your camcorder, games console, etc., as
shown.
Satellite, cable, set-top
box, LD player, etc.
Connecting a Camcorder, Games
Console, etc.
Video Connections
You only need to use one of the following connection
methods.
AUDIO
OUTPUT
L
■ Using Composite Video
R
L
AUDIO
R
Use a composite video cable to connect the AV receiver’s
VIDEO 4 INPUT VIDEO jack to the composite video
output on your camcorder, games console, etc., as
shown.
Camcorder,
games console, etc.
If your camcorder, games console, etc., has an optical
digital audio output, use an optical digital audio cable to
connect it to the AV receiver’s VIDEO 4 INPUT DIG-
ITAL jack, as shown.
VIDEO
VIDEO OUT
Camcorder,
games console, etc.
DIGITAL OUT
DIGITAL
Camcorder,
games console, etc.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 34 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
Connecting a CD Player
Connecting a Cassette Recorder
■ Using Optical or Coaxial Connections
If you connect to a digital audio input, you’ll need to
assign it (see page 42).
• Use an optical digital audio cable to connect one of the
AV receiver’s OPTICAL DIGITAL IN jacks to the
optical output on your CD player, as shown.
OR
Use an analog audio cable to connect the AV receiver’s
TAPE IN L/R jacks to the cassette recorder’s output, and
use another analog audio cable to connect the AV
receiver’s TAPE OUT L/R jacks to the cassette
recorder’s input, as shown.
• Use a coaxial digital audio cable to connect one of the
AV receiver’s COAXIAL DIGITAL IN jacks to the
coaxial output on your CD player, as shown.
OUT
IN
L
L
DIGITAL
COAXIAL
R
R
IN
TAPE
IN
REC
(IN)
PLAY
(OUT)
OPTICAL
L
L
Cassette recorder
/
R
R
Connect one or the other
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
Connecting a DAT, CD, or MD
Recorder
You can connect a DAT, CD, or MD recorder instead of
a cassette recorder.
CD player
■ Analog Connections
■ Using Analog Connections
Use an analog audio cable to connect the AV receiver’s
TAPE IN L/R jacks to the recorder’s output, and use
another analog audio cable to connect the AV receiver’s
TAPE OUT L/R jacks to the recorder’s input, as shown.
Even if your CD player is connected digitally (coaxial or
optical), to use
, or to record audio from your CD
player, you’ll need to make an analog audio connection
as well.
Use an analog audio cable to connect the AV receiver’s
CD IN L/R jacks to the analog audio output on your CD
player, as shown.
OUT
IN
L
L
IN
R
R
TAPE
CD
REC
(IN)
PLAY
(OUT)
L
L
DAT, CD, or MD recorder
AUDIO
OUTPUT
R
R
CD player
L
R
34
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 35 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
■ Using Optical or Coaxial Connections
(playback only)
If you connect to a digital audio input, you’ll need to
Note:
Don’t connect the recorder’s digital output to the AV
receiver when the recorder’s digital input is connected to
one of the AV receiver’s digital outputs. Doing so may
create a signal loop and cause a malfunction.
assign it (see page 42).
• Use an optical digital audio cable to connect one of the
AV receiver’s OPTICAL DIGITAL IN jacks to the
optical output on your recorder, as shown.
OR
• Use a coaxial digital audio cable to connect one of the
AV receiver’s COAXIAL DIGITAL IN jacks to the
coaxial output on your recorder, as shown.
DIGITAL
COAXIAL
IN
IN
OPTICAL
Connect one or the other
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
DAT, CD, or MD
recorder
■ Digital Recording
If your recorder has a digital input, by connecting it to
the AV receiver’s optical DIGITAL OUT jack, you can
record digitally. (With the TX-SR702/702E, you can use
its coaxial DIGITAL OUT jack.) However, because the
AV receiver doesn’t convert analog input signals to dig-
ital and vice versa, only input signals connected to a
DIGITAL IN jack can be recorded in this way.
DAT, CD, or MD recorder
OPTICAL
DIGITAL IN
OPTICAL
IN
OPTICAL
DIGITAL
COAXIAL
IN
Connect one or the other
OPTICAL
COAXIAL
DIGITAL OUT
DIGITAL OUT
Digital source (DAT, CD, MD player)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 36 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
■ Turntable without a Built-in Phono Preamp
Use an analog audio cable to connect an unused audio
input on the AV receiver to the audio outputs on your
phono preamp, and use another analog audio cable to
connect the phono preamp’s inputs to your turntable, as
shown.
Connecting a Turntable
For the TX-SR702/702E
The AV receiver’s PHONO IN is designed for use with a
moving magnet (MM) type cartridge.
Use an analog audio cable to connect the AV receiver’s
PHONO IN L/R jacks to the audio output on your turn-
table, as shown.
IN
AUDIO
OUTPUT
IN
L
L
R
R
PHONO
CD
AUDIO
OUTPUT
Phono preamp
L
AUDIO
OUTPUT
AUDIO
INPUT
R
L
L
R
R
Notes:
• If your turntable has a ground wire, connect it to the
AV receiver’s GND screw. With some turntables, con-
necting the ground wire may produce an audible hum.
If this happens, disconnected it.
• If your turntable has a moving coil (MC) type car-
tridge, you’ll need a commercially available MC head
amp or MC transformer. Connect your turntable to the
head amp or transformer, and then connect that to the
AV receiver’s PHONO IN L/R jacks.
■ Turntable with an MC (Moving Coil) Cartridge
Use an analog audio cable to connect an unused audio
input on the AV receiver to the audio outputs on your
phono preamp. Use another analog audio cable to con-
nect the phono preamp’s inputs to your MC head amp’s
outputs. And use another analog audio cable to connect
the MC head amp’s inputs to your turntable, as shown.
• You can also use a phono equalizer to connect a turn-
table with an MC-type cartridge. In this case, see the
phono equalizer’s manual for details.
For the TX-SR602/602E/8260
■ Turntable with a Built-in Phono Preamp
Use an analog audio cable to connect an unused audio
input on the AV receiver to the audio outputs on your
turntable, as shown.
AUDIO
INPUT
AUDIO
OUTPUT
IN
L
L
R
R
Phono preamp
CD
MC head amp or
MC transformer
AUDIO
OUTPUT
AUDIO
INPUT
L
L
R
R
AUDIO
OUTPUT
IN
L
R
CD
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 37 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
Connecting a Power Amplifier
(TX-SR702/702E only)
Connecting
Components
With
(Remote Interactive) you can control your
-compatible Onkyo CD player, DVD player, and so
on with the AV receiver’s remote controller, as follows:
If you want to connect a more powerful power amplifier
and use the AV receiver as a preamp, you can connect
one to the PRE OUT jacks. In this case, you should con-
nect all speakers and the subwoofer to that power ampli-
fier. However, if you have a powered subwoofer, connect
it to this AV receiver’s PRE OUT SUBWOOFER jack.
• To use
, you must make an analog audio con-
nection between the AV receiver and the other AV
components, even if they are connected digitally.
Auto Power On/Standby
When you start playback on an AV component con-
nected via
, if the AV receiver is in Standby, it will
turn on and select thatAV component as the input source
automatically. Similarly, when the AV receiver is set to
Standby, all components connected via
also enter
Standby. Note that this function will not work if the com-
ponent’s power cord is connected to one of the AV
receiver’s AC OUTLETS.
Direct Change
When playback is started on an AV component con-
nected via
, the AV receiver automatically selects
that AV component as the input source.
Remote Control
You can control your
-compatible Onkyo compo-
nents with the AV receiver’s remote controller.
Power amplifier
IN
IN
REMOTE
CONTROL
L
L
R
R
1
2
3
4
5
6
7
8
AUDIO
OUTPUT
e.g., DVD player
L
R
1. Subwoofer
2. Front left speaker
3. Center speaker
4. Front right speaker
5. Surround left speaker
6. Surround right speaker
7. Surround back left
speaker
8. Surround back right
speaker
AUDIO
OUTPUT
e.g., MD recorder
L
R
Notes:
• Push plugs in all the way to make good connections.
• Use only cables for connections. No
cables are supplied with this AV receiver.
• Some AV components have two
jacks. You can
connect either one to this AV receiver. The other jack
is for connecting more
• Connect the AV receiver’s
-compatible components.
jack to only OnkyoAV
components. Connecting to other manufacturer’s AV
components may cause them to malfunction.
• Some components may not support all
functions.
Refer to the manuals supplied with your components.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 38 Tuesday, September 7, 2004 1:18 PM
Connecting the AV receiver—Continued
Connecting the Power Cords of Other
Components
Turning On the AV receiver
• American &
Australian
models
• Other
models
The AV receiver has AC outlets on its rear panel that can
be used to connect the power cords of AV other compo-
nents that you intend to use with the AV receiver. These
components can then be left turned on so that they turn
on and off as and when the AV receiver is turned on and
set to Standby.
ON
STANDBY
STANDBY/ON
STANDBY/ON
POWER
Set the [POWER] switch to the
ON position ( ).
(Skip this step if you have theAmerican
or Australian model.)
1
POWER
AC OUTLETS
AC 120V 60Hz
SWITCHED
TOTAL 120W 1A MAX.
ON
The AV receiver enters Standby mode,
and the STANDBY indicator comes on.
AC OUTLETS
AC 230 240V 50Hz
SWITCHED
TOTAL 100W MAX.
-
Note:
• The remote controller has no effect
while the [POWER] switch in the
OFF position.
European and some
Asian models
American model
Press the [STANDBY/ON] button.
Alternatively, press the remote
controller’s [RECEIVER] button
followed by the [ON] button.
The AV receiver comes on, the display
lights up, and the STANDBY indicator
goes off.
Caution:
2
• Make sure that the total capacity of the components
that you connect to theAC OUTLETS does not exceed
the stated capacity (e.g., TOTAL 120 W).
Note:
• Onkyo components with
nected directly to wall outlets, not the AV receiver’s
AC OUTLETS.
jacks should be con-
Remote
controller
ON
• The number of AC OUTLETS, socket type, and total
capacity depends on the country in which you pur-
chased the AV receiver.
STANDBY
To turn off the AV receiver, press the
[STANDBY/ON] button. The AV
receiver will enter Standby mode.
Connecting the RS232 Port
The TX-SR602/602E, TX-SR8260, American and Aus-
tralian TX-SR702 do not have this port.
This port can be used to connect an external controller
for controlling the AV receiver.
Notes:
• Pressing the remote controller’s [ON] button once will
turn on the AV receiver. Pressing it again will turn on
any components connected via
Connecting the Power Cord
.
• When the AV receiver is on Standby, it will turn on
automatically when any one of its input selector but-
tons is pressed.
Not for the American and Australian models:
• The AV receiver is shipped with the POWER switch in
the ON position ( ). When the power cord is con-
nected for the very first time, the AV receiver will go
on Standby and the STANDBY indicator will light up.
• To completely shut down the AV receiver, set the
POWER switch to the OFF position ( ).
• Before connecting the power cord, connect all your
speakers and AV components.
• Turning on the AV receiver may cause a momentary
power surge that might interfere with other electrical
equipment on the same circuit. If this is a problem,
plug the AV receiver into a different branch circuit.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 39 Tuesday, September 7, 2004 1:18 PM
First Time Setup
This chapter explains the settings that you need to make before using the AV receiver.
Automatic Speaker Setup
Put the speaker setup micro-
phone in the listening position,
and connect it to the SETUP MIC
jack.
2
With the supplied speaker setup microphone, the Auto-
matic Speaker Setup function can measure the test tone
output by each speaker and automatically determine the
number of speakers connected, their sizes, the distance
from each speaker to the listening position, and so on.
Before using this function, connect and position all your
speakers.
MIC
position
Auto Speaker Setup
------------------------
Push Enter:Start
1 2
3–7
Notes:
• Wait at least five seconds after turn-
ing on the AV receiver before plug-
ging in the speaker setup
microphone.
• Make sure the microphone is hori-
zontal.
• If there’s an obstacle between the
microphone and any speaker, the
automatic setup will not work cor-
rectly. Set the room how you would
have it when enjoying a DVD.
• If the AV receiver was previously
muted, the Muting function will be
cancelled.
Turn on the AV receiver and the
connected TV.
On the TV, select the input to which the
AV receiver is connected.
1
• The automatic setup cannot be used
while a pair of headphones is con-
nected.
• By putting the microphone close to
where your ears would normally be
at the listening position, a more accu-
rate setup can be achieved. If you use
a tripod or level table, you can adjust
the height of the microphone.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
4_Setup_En Page 40 Tuesday, September 7, 2004 3:32 PM
First Time Setup—Continued
Press [ENTER].
Press the [RETURN] button to return to
the previous menu.
3
ENTER
Auto Speaker Setup
------------------------
Do not Unplug Setup Mic
1
0-1.Warning
*
------------------------
Not Connect
-:-:-:--:--:--:--:--
Wait a moment, Please.
Too Near/Far Speaker
-:-:-:--:--:--:--:--
The automatic speaker setup starts.
The test tone is output by each speaker
in turn, measured by the microphone,
and the speaker settings set accord-
ingly. The whole process takes about 90
seconds.
0-2.Speaker Config
------------------------
Subwoofer
Front
Center
Surround
:Yes
:Large
:Small
:Small
SurroundBack :Small
SurrBack ch
Crossover
:2ch
:100Hz
2
*
0-3.Distance
Auto Speaker Setup
------------------------
------------------------
Left
Center
Right
Surr Right
Surr Back R : 2.1m
Surr Back L : 2.1m
:
:
:
:
3.6m
3.6m
3.6m
2.1m
Do not Unplug Setup Mic
Left
Center
Right
Surr Left
Subwoofer
:
:
2.1m
3.6m
Surr Right
SurrBack R
SurrBack L
Surr Left
Subwoofer
0-4.Level
------------------------
Left
Center
Right
: 00dB
: 00dB
: 00dB
If any extraneous noise is picked up by
the microphone, the automatic setup
may not work correctly, so be careful.
Surr Right : 00dB
Surr Back R : 00dB
Surr Back L : 00dB
Surr Left
: 00dB
: 00dB
Subwoofer
When the Check Result menu
appears, press [ENTER].
4
(Menus vary depending on country.)
1
*
When a speaker has a warning, its abbre-
viation (e.g., L, R, and so on) appears
instead of the “---” dashes.
ENTER
Auto Speaker Setup
------------------------
Push Enter:Check Results
If you want to adjust any of the settings
manually, see “Speaker Setup” on
page 46.
Note: *2
Please set any THX Certified speakers
manually to 80 Hz after Auto setup
operation (see page 46, 47).
<:Retry
>:Set
The Setup Result menu appears.
0.Auto Sp Setup Result
------------------------
1.Warning
2.Speaker Config
3.Distance
4.Level
When you’ve checked the set-
tings,press the [RETURN] button
to return to the previous menu.
6
7
1
2
3
Warning
Number of speakers and their sizes
Distance from each speaker to the
listening position
The optimum volume level for each
speaker
Auto Speaker Setup
------------------------
Push Enter:Check Results
<:Retry
>:Set
4
When you’ve finished the auto-
matic setup, press the Right [
button.
]
Use the Up and Down [ ]/[
]
5
buttons to select the item that
you want to check, and then
press [ENTER].
ENTER
ENTER
That completes the setup.
To run the automatic setup again,
press the Left [ ] button.
The automatic speaker setup starts
again.
ENTER
Disconnect the speaker setup
microphone.
8
To cancel the automatic setup while it’s
in progress, disconnect the micro-
phone.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 41 Tuesday, September 7, 2004 1:18 PM
First Time Setup—Continued
About the Onscreen Setup Menus
The AV receiver is configured using onscreen setup menus, which are displayed on the TV that’s connected to either of
the MONITOR OUT jacks. Because they appear on your TV, they’re large and clear, making setup a breeze.
Settings are divided into two groups: Basic Setup and Advanced Setup.
When you’ve configured the settings on the Basic Setup menu correctly, you’ll be ready to enjoy movies and music. The
Advanced Setup menu contains more detailed settings for an even better sound and increased enjoyment.
Submenus
Basic Setup
1.Initial Setup
------------------------
1.Digital Input
2.Component Video
3.Hardware Setup
p. 42
p. 43
p. 44, 45
p. 46
p. 48
2.Speaker Setup
------------------------
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Equalizer Settings
p. 50
p. 51
Main menus
Menu
Advanced Setup
------------------------
Basic Setup
1.Initial Setup
2.Speaker Setup
3.Decorder Setup
------------------------
1.Analog/PCM
2.Dolby Digital
Advanced Setup
3.Decorder Setup
4.Audio Adjust
5.Listening Mode Preset
6.Preference
3.DTS
4.D.F.2ch
5.Multiplex
6.Multich Input
p. 68
p. 69
4.Audio Adjust
------------------------
1.Mono
2.PL x/Neo:6
3.Enhance
4.Orchestra
p. 70
5.Unplugged
p. 72
6.Studio-Mix
7.TV Logic
8.Mono Movie
9.Theater-Dimensional
5.Listening Mode Preset
------------------------
1.DVD/MULTICH
2.VIDEO1
3.VIDEO2
4.VIDEO3
5.VIDEO4
6.TAPE
p. 72
p. 73
7.TUNER
8.CD
9.PHONO
6.Preference
------------------------
1.IntelliVolume
2.Volume Setup
3.OSD Setup
p. 74
p. 75
4.Remote Setup
5.Digital Format
41
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 42 Tuesday, September 7, 2004 1:18 PM
First Time Setup—Continued
Initial Setup
Use the Up and Down [ ]/[
buttons to select “1. Digital
Input,” and then press [ENTER].
]
3
Digital Input
ENTER
If you connect a component to a digital input jack, you
must assign that jack to an input selector. For example, if
you connect your CD player to the OPTICAL IN2 jack,
you should assign that jack to the CD input selector. By
default, the OPTICAL IN1 jack is assigned to the DVD
input selector, although this can be changed.
The Digital Input menu appears.
Menu
------------------------
B
1.Initial Setup
------------------------
ENTER
1-1.Digital Input
------------------------
a.DVD:OPT1
b.VIDEO1
:-----
:-----
:-----
:-----
:-----
:-----
c.VIDEO2
d.VIDEO3
e.TAPE
f.CD
g.PHONO
1
• There are no assignments for
TUNER and VIDEO 4.
2, 3
Use the Up and Down [ ]/[
]
2–4
4
buttons to select an input selec-
tor, and then use the Left and
Right [ ]/[ ] buttons to select a
digital input jack.
ENTER
1, 5
Examples:
If you connect your DVD player to the
OPTICAL IN 2 jack, set “a. DVD” to
“OPT2.”
If you want to listen to audio from the
component connected to the OPTICAL
IN 3 jack when the VIDEO 1 input
selector is selected, set “b. VIDEO1” to
“OPT3.”
If you want to listen to audio from the
component connected to the COAX-
IAL IN 1 jack when theVIDEO 2 input
selector is selected, set “c. VIDEO2” to
“COAX1.”
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
1
RECEIVER
For input selectors that you don’t want
to assign a digital input jack, leave them
set to “-----.”
Use the Up and Down [ ]/[
buttons to select “1. Initial
Setup,” and then press [ENTER].
]
2
Press the [SETUP] button.
The setup menu closes.
5
ENTER
The Initial Setup menu appears.
Note:
ENTER
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 43 Tuesday, September 7, 2004 1:18 PM
First Time Setup—Continued
Component Video Setup
Use the Up and Down [ ]/[
]
4
If you connect to a COMPONENTVIDEO IN, you must
assign it to an input selector. For example, if you connect
your DVD player to COMPONENT IN 3, you should
assign it to the DVD input selector.
buttons to select an input selec-
tor, and then use the Left and
Right [ ]/[ ] buttons to select:
IN1: Use the video component
connected to COMPO-
ENTER
For the TX-SR702/702E, TX-SR602E, and Australian
TX-SR602, if you want to output composite and S-Video
sources from the COMPONENT VIDEO OUT, select
Video, as explained below.
NENT VIDEO IN 1.
IN2: Use the video component
connected to COMPO-
NENT VIDEO IN 2.
IN3: Use the video component
connected to COMPO-
Input
selector
Analog audio
input (fixed)
COMPONENT
VIDEO IN jack
DVD
DVD
IN 1
NENT VIDEO IN 3.
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
*
*
*
*
Video*: Output composite video
and S-Video sources from
the COMPONENT
VIDEO OUT.
Last: Select this for audio-only
components.
*On the TX-SR702/702E, TX-SR602E, and Australian
TX-SR602, the default setting is Video. For other models, the
default setting is Last.
* TX-SR702/702E, TX-SR602E, and Austra-
lian TX-SR602 only.
Press the [SETUP] button.
The setup menu closes.
5
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
1
RECEIVER
The main menu appears onscreen.
Notes:
• If you select Last, the video source remains the same
when you select another input selector. For example,
if you set VIDEO 1 to Last, select the DVD input
selector, then select the VIDEO 1 input selector, you
can watch a DVD while listening to audio from the
component connected to the VIDEO 1 IN L/R jacks.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
Use the Up and Down [ ]/[
buttons to select “1. Initial
Setup,” and then press [ENTER].
]
2
3
ENTER
The initial Setup menu appears.
ENTER
Use the Up and Down [ ]/[
]
buttons to select “2. Component
Video,” and then press the
[ENTER] button.
ENTER
The Component Video Setup menu
appears.
Menu
------------------------
ENTER
1.Initial Setup
------------------------
1-2.Component Video
------------------------
a.DVD/MULTICH:IN1
b.VIDEO1
:Video
:Video
:Video
c.VIDEO2
d.VIDEO3
e.VIDEO4
:Video
43
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 44 Tuesday, September 7, 2004 1:18 PM
First Time Setup—Continued
Minimum Speaker Impedance
(not American models)
Use the Up and Down [ ]/[
buttons to select “1. Initial
Setup,” and then press [ENTER].
]
2
3
ENTER
This setting is not set automatically by the Automatic
Speaker Setup function (see page 39).
The Initial Setup menu appears.
If the impedance of any of the connected speakers is 4
ohms or more, but less than 6 ohms, set the Minimum
Speaker Impedance to “4 ohms.”
ENTER
Note:
Before you change this setting, turn down the volume.
Use the Up and Down [ ]/[
]
buttons to select “3. Hardware
Setup,” and then press [ENTER].
The Hardware Setup menu appears.
ENTER
Menu
------------------------
B
1.Initial Setup
------------------------
ENTER
1-3.Hardware Setup
------------------------
a.PoweredZone2
:Not Activated
b.Sp Impedance Minimum
:6ohms
:NTSC
c.TV Format
1
d.AM Frequency Step
: 9kHz
(Menus vary depending on country.)
Use the Up and Down [ ]/[
buttons to select “b. Sp Imped-
ance Minimum,”and then use the
Left and Right [ ]/[ ] buttons to
select:
4 ohms: Select if the impedance of any
connected speaker is 4 ohms
or more, but less than 6 ohms.
6 ohms: Select if the impedances of all
connected speakers are
2, 3
2–4
]
4
5
1, 5
ENTER
between 6 and 16 ohms.
Press the [SETUP] button.
The setup menu closes.
Notes:
Press the [RECEIVER] button fol-
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
1
RECEIVER
lowed by the [SETUP] button.
The main menu appears onscreen.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 45 Tuesday, September 7, 2004 1:18 PM
First Time Setup—Continued
TV Format Setup (not American models)
AM Frequency Step Setup
(some models only)
Here you can specify the TV format used in your area.
Here you can specify the AM frequency step used in
your area. When this setting is changed, all radio presets
are deleted.
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
1
RECEIVER
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
1
RECEIVER
The main menu appears onscreen.
Use the Up and Down [ ]/[
buttons to select “1. Initial
Setup,” and then press [ENTER].
]
2
3
Use the Up and Down [ ]/[
buttons to select “1. initial
Setup,” and then press [ENTER].
]
The Initial Setup menu appears.
2
3
Use the Up and Down [ ]/[
]
The Initial Setup menu appears.
buttons to select “3. Hardware
Setup,” and then press [ENTER].
The Hardware Setup menu appears.
ENTER
Use the Up and Down [ ]/[
]
buttons to select “3. Hardware
Setup,” and then press [ENTER].
The Hardware Setup menu appears.
ENTER
Menu
------------------------
B
1.Initial Setup
------------------------
1-3.Hardware Setup
ENTER
Menu
------------------------
------------------------
a.PoweredZone2
B
1.Initial Setup
:Not Activated
------------------------
b.Sp Impedance Minimum
1-3.Hardware Setup
ENTER
:6ohms
:NTSC
c.TV Format
------------------------
a.Powered Zone2
:Not Activated
d.AM Frequency Step
: 9kHz
b.Sp Impedance Minimum
:6ohms
:NTSC
c.TV Format
(Menus vary depending on country.)
Use the Up and Down [ ]/[
buttons to select “c.TV Format,”
and then use the Left and Right
d.AM Frequency Step
: 9kHz
]
4
5
Use the Up and Down [ ]/[
buttons to select “d. AM Fre-
quency Step,” and then use the
Left and Right [ ]/[ ] buttons to
select:
10 kHz: Select if 10 kHz steps are
used in your area.
9 kHz: Select if 9 kHz steps are used
in your area.
]
4
5
ENTER
[
]/[ ] buttons to select:
Auto: Conforms with the video
input signal.
ENTER
PAL: Select if the TV system in
your area is PAL.
NTSC: Select if the TV system in
your area is NTSC.
Press the [SETUP] button.
The setup menu closes.
Press the [SETUP] button.
The setup menu closes.
Note:
Note:
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 46 Tuesday, September 7, 2004 1:18 PM
First Time Setup—Continued
Speaker Setup
Use the Up and Down [ ]/[
buttons to select “2. Speaker
Setup,” and then press [ENTER].
]
2
3
Some of the settings in this section are set automatically
by the Automatic Speaker Setup function (see page 39).
Here you can check the settings made by the Automatic
Speaker Setup function, or set them manually, which is
useful if you change one of the connected speakers after
using the Automatic Speaker Setup function.
ENTER
The Speaker Setup menu appears.
ENTER
Speaker Configuration
This setting is set automatically by the Automatic
Speaker Setup function (see page 39).
Use the Up and Down [ ]/[
buttons to select “1. Speaker
Config,” and then press [ENTER].
]
Here you can specify which speakers are connected and
their individual sizes.
ENTER
The Speaker Config menu appears.
For speakers with a cone diameter
over 6-1/2 inches (16 cm), specify
large, and for those with a diameter
below this, specify small.
Menu
------------------------
2.Speaker Setup
------------------------
ENTER
2-1.Speaker Config
------------------------
For the TX-SR702/702E, if you’re
using THX-certified speakers, spec-
ify Small for all speakers.
a.Subwoofer:Yes
b.Front
:Large
:Small
Cone diameter
c.Center
d.Surround
:Small
e.SurroundBack :Small
f.SurrBack ch
:2ch
:100Hz
:Off
g.Crossover
h.Double Bass
Use the Up and Down [ ]/[
buttons to select “a. Subwoofer,”
and then use the Left and Right
]
4
5
1
ENTER
[
]/[ ] buttons to select:
Yes: Select if a subwoofer is con-
nected.
2, 3
No: Select if no subwoofer is con-
nected.
2–11
1, 12
Use the Up and Down [ ]/[
buttons to select “b. Front,” and
then use the Left and Right [ ]/
]
ENTER
[
] buttons to select:
Small: Select if the front speakers are
small.
Large: Select if the front speakers are
large.
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
1
RECEIVER
Note:
• If the Subwoofer setting in step 4 is
set to No, this setting is fixed at
Large.
The main menu appears onscreen.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 47 Tuesday, September 7, 2004 1:18 PM
First Time Setup—Continued
Use the Up and Down [ ]/[
buttons to select “c. Center,” and
then use the Left and Right [ ]/
]
Use the Up and Down [ ]/[
buttons to select “f. SurrBack
ch,” and then use the Left and
Right [ ]/[ ] buttons to select:
1ch: Select if one surround back
speaker is connected.
]
6
7
8
9
ENTER
ENTER
[
] buttons to select:
Small: Select if the center speaker is
small.
2ch: Select if two (left and right)
surround back speakers are
connected.
Large: Select if the center speaker is
large.
None: Select if no center speaker is
connected.
Continue with step 10 in the right col-
umn.
Note:
• If the Front setting in step 5 is set to
Small, the Large option cannot be
selected.
Crossover
Use the Up and Down [ ]/[
buttons to select “d. Surround,”
and then use the Left and Right
]
Use the Up and Down [ ]/[
buttons to select “g. Crossover,”
and then use the Left and Right
]
10
ENTER
[
]/[ ] buttons to select:
Small: Select if the surround left and
right speakers are small.
ENTER
[
]/[ ] buttons to select a
crossover frequency.
Large: Select if the surround left and
right speakers are large.
None: Select if no surround left and
right speakers are connected.
Choose a crossover frequency suitable
for your setup. If you’re using a sub-
woofer, choose a crossover frequency
based on the diameter of your front
speakers. If you’re not using a sub-
woofer, use the diameter of any speaker
that you specified as Small.
Note:
• If the Front setting in step 5 is set to
Small, the Large option cannot be
selected.
For the TX-SR702/702E, if you’re
using THX-certified speakers, select
80Hz (THX).
Use the Up and Down [ ]/[
]
buttons to select “e. Surround
Back,” and then use the Left and
Right [ ]/[ ] buttons to select:
Small: Select if the surround back
left and right speakers are
Speaker cone
diameter
Crossover
frequency
ENTER
Over 12 in.
(30 cm)
40Hz*
60Hz
small.
8 to 12 in.
(20–30 cm)
Large: Select if the surround back
speakers are large.
None: Select if no surround back
speakers are connected.
6-1/2 to 8 in.
(16–20 cm)
80Hz (THX)
100Hz
5-1/4 to 6-1/2 in.
(13–16 cm)
Notes:
• If the Surround setting in step 7 is set
to None, this setting cannot be
selected.
• If the Surround setting in step 7 is set
to Small, this setting cannot be set to
Large.
3-1/2 to 5-1/4 in.
(9–13 cm)
120Hz
Under 3-1/2 in.
(9 cm)
150Hz
*TX-SR702/702E only.
Continue with step 11 on the next page.
Notes:
• If the crossover frequency is set to a low value, and the
program material doesn’t contain any sounds below
that frequency, the subwoofer will not output much
sound.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
4_Setup_En Page 48 Tuesday, September 7, 2004 3:10 PM
First Time Setup—Continued
Double Bass
Speaker Distance
This setting is not set automatically by the Automatic
Speaker Setup function (see page 39).
This setting is set automatically by the Automatic
Speaker Setup function (see page 39).
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left and right
channels to the subwoofer. This function can be set only
if the Subwoofer setting in step 4 is set to Yes, and the
Front setting in step 5 is set to Large.
Here you can specify the distance from each speaker to
the listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer
intended.
In the speaker setup screen, you can choose how bass
information is distributed to your speakers only if you
have large front left and right speakers AND a sub-
woofer.
1
Use the Up and Down [ ]/[
buttons to select “h. Double
]
2, 3
11
2–5
Bass,” and then use the Left and
Right [ ]/[ ] buttons to select:
On: Double Bass function on.
Front left and right bass also
goes to the subwoofer simul-
taneously.
ENTER
1, 7
Off: Double Bass function off
(default).
With the TX-SR702/702E,
“Double Bass Off” is pre-
ferred by THX but to decide
which setting is best for your
room, once you have posi-
tioned all of your speakers,
choose the option which gives
you the most solid sounding
bass.
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
1
RECEIVER
Use the Up and Down [ ]/[
buttons to select “2. Speaker
Setup,” and then press [ENTER].
]
2
3
Press the [SETUP] button.
The setup menu closes.
12
ENTER
The Speaker Setup menu appears.
Notes:
ENTER
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
Use the Up and Down [ ]/[
buttons to select“2. Speaker Dis-
tance,” and then press [ENTER].
]
ENTER
ENTER
48
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 49 Tuesday, September 7, 2004 1:18 PM
First Time Setup—Continued
• On the TX-SR602/602E and TX-SR8260, the Center
and Subwoofer distances can be set up to 5 ft. (1.5 m)
more or less than the Front distance. For example, if
the Front distance is set to 20 ft. (6 m), the Center and
Subwoofer distances can be set between 15 and 25 ft.
(4.5 and 7.5 m). The SurrRight, Surr Left, and Surr
Back distances can be set up to 5 ft. (1.5 m) more or
15 ft. (4.5 m) less than the Front distance. For exam-
ple, if the Front distance is set to 20 ft. (6 m), the Sur-
rRight, Surr Left, and Surr Back distances can be set
between 5 and 25 ft. (1.5 and 7.5 m).
The Speaker Distance menu appears.
Menu
------------------------
2.Speaker Setup
------------------------
2-2.Speaker Distance
------------------------
a.Unit :meters
b.Left
: 3.6m
: 3.6m
c.Center
d.Right
: 3.6m
e.Surr Right : 2.1m
f.Surr Back R : 2.1m
g.Surr Back L : 2.1m
h.Surr Left
i.Subwoofer
: 2.1m
: 3.6m
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
(This menu may be slightly different on
the TX-SR602/602E and TX-SR8260.)
Note:
Speakers that you set to No or None on
the Speaker Configuration page
(page 46) cannot be selected.
Use the Up and Down [ ]/[
buttons to select “a. Unit,” and
then use the Left and Right [ ]/
]
4
5
ENTER
[
] buttons to select:
feet: Select if you want to enter
distances in feet. Can be set
from 1 to 30 feet in 1-foot
steps.
meters: Select if you want to enter
distances in meters. Can be
set from 0.3 to 9 meters in
0.3-meter steps.
Use the Up and Down [ ]/[
buttons to select “b. Left,” and
]
then use the Left and Right [ ]/
ENTER
[
] buttons to specify the dis-
tance.
Specify the distance from the front left
speaker to your listening position.
Repeat step 5 for all speakers.
6
7
Press the [SETUP] button.
The setup menu closes.
Notes:
• On the TX-SR702/702E, if the distance between the
furthest and nearest speakers is greater than 20 feet (6
meters), corrected values suitable for home theater use
will be set automatically.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
4_Setup_En Page 50 Tuesday, September 7, 2004 2:06 PM
First Time Setup—Continued
Speaker Level Calibration
Use the Up and Down [ ]/[
]
3
buttons to select “3. Level Cali-
bration,” and then press
[ENTER].
This setting is set automatically by the Automatic
Speaker Setup function (see page 39).
ENTER
The Level Calibration menu appears
and the pink noise test tone is output by
the front left speaker.
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
ENTER
Notes:
Menu
------------------------
• The speakers cannot be calibrated while the output of
the AV receiver is muted, while a pair of headphones
is connected, or when using the multichannel input.
• Because the TX-SR702/702E supports THX, the
test tone is output at the standard level of 0 dB
(absolute volume setting 82). If you normally listen
at volume settings below this, be careful because
the test tone will be much louder.
B
2.Speaker Setup
------------------------
2-3.LevelCalibration
------------------------
a.Left :0dB
b.Center : 0dB
c.Rught
: 0dB
d.SurrRight : 0dB
e.SurrBack R : 0dB
f.SurrBack L : 0dB
g.SurrLeft
h.Subwoofer
: 0dB
: 0dB
Note:
Speakers that you set to No or None on
the Speaker Configuration page
(page 46) cannot be selected.
1
Use the Up and Down [ ]/[
buttons to select each speaker,
and use the Left and Right [ ]/
]
4
5
ENTER
2, 3
[
] buttons to set the volume.
The volume can be adjusted from –12
to +12 dB in 1 dB steps (–15 to +12 dB
for the subwoofer).
2–4
1, 6
Repeat step 4 until the volume of
the test tone from each speaker
is the same.
When using a handheld Sound Level
Meter, calibrate each loudspeaker
channel (Left, Center, Right, Right Sur-
round, Surround Back Right, Surround
Back Left, Left Surround, and Sub-
woofer) to 75 dB SPL at the listening
position, measured with C-weighting
and slow reading.
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
1
RECEIVER
Press the [SETUP] button.
The setup menu closes.
6
Use the Up and Down [ ]/[
buttons to select “2. Speaker
]
2
ENTER
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
Notes:
• This procedure can also be performed by using the
remote controller. First press the [TEST TONE] but-
ton to output the test tone. Use the [LEVEL–] and
[LEVEL+] buttons to set the volume, and use the [CH
SEL] button to select the speakers.
ENTER
50
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 51 Tuesday, September 7, 2004 1:18 PM
First Time Setup—Continued
Equalizer Setting
Use the Left and Right [ ]/[
buttons to select:
]
4
5
This setting is set automatically by the Automatic
Speaker Setup function (see page 39).
Off: Tone off, response flat.
ENTER
Auto: The tone for each speaker is
set automatically by theAuto-
matic Speaker Setup function.
Manual:You can adjust the EQ of each
speaker manually.
If you select Manual, continue with this
procedure. If you select Off orAuto, go
to step 8.
Here you can adjust the EQ of individual speakers. The
volume of individual speakers can be set on page 50.
Use the Down [ ] button to
select a speaker.
1
ENTER
Menu
------------------------
2, 3
2.Speaker Setup
------------------------
2–7
2-4.Equalizer Settings
Use Settings :Manual
------------------------
Left
1, 8
a. 80Hz
: 0dB
b. 250Hz
: 0dB
: 0dB
: 0dB
: 0dB
c. 800Hz
d.2.5kHz
e. 8kHz
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
1
RECEIVER
Use the Up and Down [ ]/[
buttons to select a frequency,
and then use the Left and Right
]
6
The main menu appears onscreen.
ENTER
[
]/[ ] buttons to adjust the
level at that frequency.
The volume at each frequency can be
adjusted from –12 to +12 dB in 1 dB
steps.
Tip: Low frequencies (e.g., 80Hz)
affect bass sounds; high frequencies
(e.g., 8kHz) affect treble sounds.
Use the Up and Down [ ]/[
buttons to select “2. Speaker
Setup,” and then press [ENTER].
]
2
3
ENTER
The Speaker Setup menu appears.
Menu
------------------------
Use the Up [ ] button to select
“Left,” and then use the Left and
Right [ ]/[ ] buttons to select
another speaker.
7
8
B
2.Speaker Setup
------------------------
1.Speaker Config
ENTER
2.Speaker Distance
3.Level Calibration
4.Equalizer Settings
Repeat steps 6 and 7 for each speaker.
Press the [SETUP] button.
The setup menu closes.
Use the Up and Down [ ]/[
]
buttons to select “4. Equalizer
Settings,” and then press
[ENTER].
ENTER
The Equalizer Settings menu appears.
Notes:
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
ENTER
51
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 52 Tuesday, September 7, 2004 1:18 PM
First Time Setup—Continued
Changing the TAPE/MD/CDR Display
If you connect an
-compatible Onkyo MiniDisc
recorder or CD recorder to the TAPE IN/OUT jacks, for
to work properly, you must change this setting.
This setting can only be changed on the AV receiver.
1, 2
(TX-SR702 shown here)
Press the [TAPE] input selector
button so that “TAPE” appears
on the display.
1
Press and hold down the [TAPE]
2
input selector button (about 3
seconds) to set the display.
Repeat this step to select TAPE, MD, or
CDR.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 53 Tuesday, September 7, 2004 1:18 PM
Basic Operation
Selecting the Input Source
This section explains how to select the input source (i.e., the AV component that you want to listen to or watch).
3
1
1
3
1
Use the AV receiver’s input selector buttons to select the input
source.
Remote
controller
1
AV receiver
RECEIVER
To select the input source with the remote controller, press the
[RECEIVER] button, and then use the INPUT SELECTOR buttons.
or
On the remote controller, the [V1], [V2], [V3], and [V4] buttons select the
VIDEO 1, VIDEO 2, VIDEO 3, and VIDEO 4 input sources respectively.
Only the RC-588M remote controller has a [PHONO] button.
Start playback on the source component.
2
3
When you select DVD or another video component, on your TV, you’ll need to
select the video input that’s connected to the AV receiver’s MONITOR OUT.
On some DVD players, you may need to turn on the digital audio output.
To adjust the volume, use the MASTER VOLUME control, or the
remote controller’s [VOL] button.
Remote
controller
AV receiver
MASTER VOLUME
The volume can be set to MIN, 1 through 99, or MAX.
The AV receiver is designed for home theater enjoyment. It has a wide volume
range, allowing precise adjustment.
VOL
or
53
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 54 Tuesday, September 7, 2004 1:18 PM
Basic Operation—Continued
Using the Sleep Timer
With the sleep timer, you can set the AV receiver to auto-
matically turn off after a specified period.
Press the [RECEIVER] button,
and then press the [SLEEP] but-
ton repeatedly to select the
required sleep time.
The sleep time can be set from 90 to 10
Press
[RECEIVER]
first
RECEIVER
DIMMER
SLEEP
SLEEP
minutes in 10 minute steps.
The SLEEP indicator appears on the
display when the sleep timer has been
set, as shown. The specified sleep time
appears on the display for about five
seconds, then the previous display
reappears.
MUTING
If you need to cancel the sleep timer, press the [SLEEP]
button repeatedly until the SLEEP indicator disappears.
Setting the Display Brightness
You can adjust the brightness of the display.
To check the time remaining until the AV receiver sleeps,
press the [SLEEP] button. Note that if you press the
[SLEEP] button while the sleep time is being displayed,
you’ll shorten the sleep time by 10 minutes.
Press the [RECEIVER] button,
RECEIVER
and then press the [DIMMER]
button repeatedly to select:
• Normal+VOLUME light on.
Using Headphones
DIMMER
• Normal+VOLUME light off.
You can connect a pair of stereo headphones (1/4-inch
phone plug) to the AV receiver’s PHONES jack for pri-
vate listening, as shown.
• Dim+VOLUME light off.
• Dimmer+VOLUME light off.
Muting the AV receiver
PHONES
You can temporarily mute the output of the AV receiver.
Press the [RECEIVER] button,
and then press the [MUTING] but-
RECEIVER
Notes:
ton.
• Always turn down the volume before connecting your
headphones.
• The speakers are turned off while the headphones plug
is inserted in the PHONES jack. (Zone 2 speakers are
not turned off.)
The output is muted and the MUTING
indicator flashes on the display, as
shown.
MUTING
• When you connect a pair of headphones, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio (not American
TX-SR602). When you disconnect the headphones,
the previous listening mode is resumed.
• Only the Stereo, Direct, Pure Audio (not American
TX-SR602), and Mono listening modes can be used
with headphones. (The listening modes available also
depends on the currently selected input source.)
• When the multichannel input is used, only the front
left and right audio can be heard in the headphones.
On the TX-SR702E, when the Stereo or Mono listen-
ing mode is selected, audio is downmixed for a good
sound.
To unmute the AV receiver, press the
[MUTING] button again, or adjust the
volume.
The Mute function is cancelled when
the AV receiver is set to Standby.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 55 Tuesday, September 7, 2004 1:18 PM
Basic Operation—Continued
Displaying Source Information
You can display various information about the current
input source as follows.
RECEIVER
DISPLAY
Press the [RECEIVER] button,
RECEIVER
and then press the [DISPLAY]
button repeatedly to cycle
through the available informa-
tion.
DISPLAY
The following information can typically be displayed for
input sources.
Input source &
volume
Signal format*
or sampling
frequency
Input source &
listening mode
*If the input signal is analog, no format information is
displayed. If the input signal is PCM, the sampling fre-
quency is displayed. If the input signal is digital but not
PCM, the signal format is displayed. Information is dis-
played for about three seconds, then the previously dis-
played information reappears.
Interpreting Surround Channel Values
A
B
C
A: The number of front channels (3 means front left,
front right, and center).
B: The number of surround channels (2 means surround
left and surround right). If there’s surround back
channel information, this will be 3.
C: LFE channel for subwoofer (1 means yes).
55
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 56 Tuesday, September 7, 2004 1:18 PM
Basic Operation—Continued
■ Manual Tuning Mode
Using the Tuner
Press the [TUNING MODE] button
so that the AUTO indicator disap-
pears from the display.
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as presets
for quick selection.
1
Listening to the Radio
Press and hold theTUNING Up or
Down [ ]/[ ] button.
The frequency stops changing when
you release the button.
Press the buttons repeatedly to change
the frequency one step at a time.
2
Use the [TUNER] input selector
button to select either AM or FM.
1
In this example, FM has been selected.
Band
Frequency
TheAmerican model changes FM frequency in 0.2 MHz
steps, 10 kHz steps for AM. For other models it’s
0.05 MHz steps for FM and 9 kHz steps for AM.
In Manual Tuning mode, FM stations will be in mono.
(Actual display depends on country.)
Tuning into weak FM stereo stations
Tuning into Radio Stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
1 2
■ Auto Tuning Mode
Press the [TUNING MODE] button
so that the AUTO indicator
appears on the display.
1
Press the TUNING Up or Down
2
[
]/[ ] button.
Searching stops when a station is
found.
When tuned into a station, the TUNED indicator
appears. When tuned into a stereo FM station, the FM
STEREO indicator appears on the display, as shown.
TUNED AUTO
FM STEREO
56
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 57 Tuesday, September 7, 2004 1:18 PM
Basic Operation—Continued
Presetting Radio Stations
Deleting Presets
2, 4
3
2
You can store up to 40 of your favorite radio stations as
presets.
Select the preset that you want to
delete.
See the previous section.
1
2
Tune into the station that you
want to store as a preset.
1
While holding down the [MEM-
ORY] button, press the
[TUNING MODE] button.
The selected preset is deleted and its
number disappears from the display.
Press the [MEMORY] button.
The MEMORY indicator appears and
the preset number flashes.
2
Displaying Radio Information
While the MEMORY indicator is
3
displayed (about 8 seconds), use
the PRESET [ ]/[ ] buttons to
select a preset from 1 through 40.
In this example, preset #3 is selected.
2
Press the [MEMORY] button
4
again to store the station.
The station is stored and the preset
number stops flashing.
Press the [DISPLAY] button
repeatedly to cycle through the
available information.
1
Repeat this procedure for all your
favorite radio stations.
Selecting Preset Stations
Band, preset # &
frequency
Use the [TUNER] input selector
1
button to select either AM or FM.
Listening mode
Use the PRESET [ ]/[ ] but-
tons, or the remote controller’s
CH [+/–] button to select a preset.
2
57
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 58 Tuesday, September 7, 2004 1:18 PM
Basic Operation—Continued
Using RDS (European models only)
Program Types Used in Europe (PTY)
RDS only works with European models and only in areas
where RDS broadcasts are available.
Type
Display
NONE
NEWS
Description
None
No program type.
■ What is RDS?
News
reports
Reports on current events and
happenings.
RDS stands for Radio Data System and it’s a method of
transmitting data in FM radio signals. It was developed
by the European Broadcasting Union (EBU) and is avail-
able in most European countries. Many FM stations use
it these days. In addition to displaying text information,
RDS can also help you find radio stations by type (e.g.,
news, sport, rock, etc).
Current
affairs
AFFAIRS Topical reporting of current
affairs, often with a wider
range of topics than news
reports.
Information INFO
General information such as
weather forecasts, consumer
affairs, medical help, etc.
The AV receiver supports four types of RDS informa-
tion:
Sport
SPORT
Live sports action, sports
news, and interviews.
PS (Program Service)
Education EDUCATE Formal educational programs.
When tuned to an RDS station that’s broadcasting PS
information, the station’s name appears. When you press
the [DISPLAY] button, the frequency is displayed for
three seconds.
Drama
Culture
DRAMA
Radio plays and serials.
CULTURE Cultural programs (including
religious affairs).
Scienceand SCIENCE Programs about the natural
RT (Radio Text)
technology
sciences and technology.
When tuned to an RDS station that’s broadcasting RT
text information, that information is shown on the dis-
play (see page 59).
Varied
VARIED
Speech-based programs not
covered by the above catego-
ries (e.g., quizzes, panel
games, and comedy).
PTY (Program Type)
You can also search for radio stations by type (see
page 59).
Pop music POP M
Popular commercial music,
usually from past or present
sales charts (e.g., Top 40).
TP (Traffic Program)
You can also search for TP radio stations (see page 59).
Rock music ROCK M Popular music with an alterna-
tive appeal, often not appear-
Notes:
ing on sales charts.
• In some cases, the text characters displayed on the AV
receiver may not be identical to those broadcast by the
radio station. Also, unexpected characters may be dis-
played when unsupported characters are received.
This is not a malfunction.
Middle of
the road
music
M.O.R.M Easy listening music (as
opposed to Pop, Rock, or
Classical).
Light
classics
LIGHT M Classical music for general
rather than specialist appreci-
ation.
• If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
Serious
classics
CLASSICS Performances of major
orchestral works, sympho-
nies, chamber music, etc.
(including the Grand Opera).
Other music OTHER M Music styles not covered by
the above categories (e.g.,
Jazz, Rhythm & Blues, Folk,
Country, and Reggae).
Alarm
ALARM
When an RDS station is mak-
ing an emergency broadcast,
ALARM will flash on the dis-
play.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 59 Tuesday, September 7, 2004 1:18 PM
Basic Operation—Continued
Displaying Radio Text (RT)
To start the search, press
[ENTER].
The AV receiver searches until it finds a
station of the type you specified, at
which point it stops briefly before con-
tinuing with the search.
4
5
1
When a station you want to listen
to is found, press [ENTER].
If no stations are found, the message
“Not Found” appears.
When tuned to an RDS station that’s broadcasting RT
text information, that information can be displayed.
Listening to Traffic News (TP)
Press the [RT/PTY/TP] button
once.
1
1 2 3
The RT information scrolls across the
display.
Notes:
• The message “Waiting” may appear while the AV
receiver waits for RT information.
• If the message “No Text Data” appears on the display,
no RT information is available.
You can search for TP radio stations.
Finding Stations by Type (PTY)
Use the [TUNER] input selector
button to select FM.
1
1 2 4, 5 3
Press the [RT/PTY/TP] button
three times.
2
If the current radio station is broadcast-
ing TP (Traffic Program), “[TP]” will
appear on the display, and traffic news
will be heard as and when it’s broad-
cast. If “TP” without square brackets
appears, this means that the station is
not broadcasting TP.
You can search for radio stations by type.
Use the [TUNER] input selector
1
button to select FM.
To locate a station that is broad-
casting TP, press [ENTER].
The AV receiver searches until it finds a
station that’s broadcasting TP.
If no stations are found, the message
“Not Found” appears.
3
Press the [RT/PTY/TP] button
twice.
The current program type appears on
the display.
2
Use the PRESET [ ]/[ ] buttons
to select the type of program you
want.
3
See the table on page 58.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 60 Tuesday, September 7, 2004 1:18 PM
Basic Operation—Continued
Selecting with the Remote Controller
Selecting Listening Modes
RC-588M
See “About the Listening Modes” on page 62 for
detailed information about the listening modes.
ALL ST
THX
• The Dolby Digital and DTS listening modes
can only be selected if your DVD player is
connected to the AV receiver with a digital
audio connection (coaxial or optical).
• Listening mode availability depends on the
format of the current input signal.
STEREO
SURR
PURE A
DIRECT
DSP
DSP
Selecting on the AV receiver
RC-590M/591M
STEREO
ALL ST
STEREO
SURR
PURE A
(not
RC-590M)
DSP
DSP
DIRECT
■ [SURR] button
PURE AUDIO
LISTENING MODE
This button selects the Dolby Digital, Pro Logic IIx,
Neo:6, DTS, and other listening modes.
■ [PURE AUDIO] button (not American
TX-SR602)
■ [All ST] button
This button selects the Pure Audio listening mode.
While this mode is selected, the AV receiver outputs
no video signals and its display is turned off.
This button selects the All Ch Stereo listening mode.
■ [THX] button (TX-SR702/702E only)
This button selects the THX listening modes.
■ [STEREO] button
■ [STEREO] button
This button selects the Stereo listening mode.
This button selects the Stereo listening mode.
■ LISTENING MODE [ ] [ ] buttons
These buttons select all the listening modes that can
be used with the current input source.
■ [PURE A] button (not American TX-SR602)
This button selects the Pure Audio listening mode.
While this mode is selected, the AV receiver outputs
no video signals and its display is turned off.
Modes can be selected in the following order,
depending on the input signal format:
Pure Audio ➔ Direct ➔ Mono ➔ Surround (e.g.,
PLIIx, Neo:6, Dolby D EX, DTS/DTS 96/24, DTS-
ES, and so on) ➔ Onkyo original DSP
■ [DIRECT] button
This button selects the Direct listening mode.
■ [ DSP] & [DSP ] buttons
These buttons select the Onkyo original DSP modes.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 61 Tuesday, September 7, 2004 1:18 PM
Basic Operation—Continued
The following table lists all the listening modes and shows which modes can be selected for each input signal format.
Dolby D
DTS/DTS 96/24*2
1/0,
Analog,
PCM*1
Input signal format
Multich
DTS-
ES
*/2
2/0 1/0,1+1 Other
*/2
2/0
Other
1+1
CD, TV, LD,
VHS, MD,
turntable,
radio,
cassette,
DTV, etc.
Source
DVD, DTV, etc.
DVD, LD, CD, etc.
DVD
Listening mode
❍
❍
❍
❍
Pure Audio
Direct
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
Stereo
❍*3
❍*3
Mono
PLIIx Movie/Music/Game *4
Neo:6 Cinema
Neo:6 Music *5
Dolby D
❍
❍
❍
❍
❍
Dolby D EX *6
Dolby D+PLIIx Movie *7
Dolby D+PLIIx Music *6
DTS, DTS 96/24
❍
❍
❍
❍
❍
❍*8
DTS+Neo:6 *6
DTS+Dolby EX *6
DTS+PLIIx Movie *7, Music *6
DTS-ES Discrete *6
DTS-ES Matrix *6
Multich
Discrete
Matrix
❍
Multich+Dolby EX *6
Multich+PLIIx Movie *7, Music *6
*9 PLIIx+THX Cinema *4
*9 Neo:6+THX Cinema
*9 THX Cinema
❍*3
❍*3
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍*8
❍*3
❍*3
❍*3
*9 THX SurrEX *6
*9 PLIIx+THX Cinema *7
*9 DTS+Neo:6+THX Cinema *6
*9 DTS-ES+THX Cinema *6
Mono Movie
❍
❍
Enhance
Orchestra
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍*3
Unplugged
Studio-Mix
TV Logic
All Ch Stereo
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍*3
❍*3
❍*3
Full Mono
Theater-Dimensional
1. In the Pure Audio and Direct listening modes, PCM signals at 32 kHz, 44.1 kHz, and 48 kHz are processed at 64 kHz, 88.2 kHz, and 96 kHz respec-
tively. 96 kHz signals are processed at 48 kHz for all listening modes other than Pure Audio, Direct, and Stereo.
2. In the Pure Audio, Direct, Stereo, and DTS 96/24 listening modes, signals are processed as DTS 96/24. Everything else processed as DTS.
3. TX-SR702E only.
4. If the SurrBack parameter is set to “None,” or the Zone 2 speakers are being used, PLII is used.
5. Available only when Surround speakers are connected.
6. Cannot be selected if the SurrBack parameter is set to “None” or the Zone 2 speakers are being used.
7. Cannot select if the SurrBack ch setting is not set to “2ch,” or the Zone 2 speakers are being used.
8. If the SurrBack setting is set to “None,” or the Zone 2 speakers are being used, DTS is used.
9. TX-SR702/702E only.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 62 Tuesday, September 7, 2004 1:18 PM
Basic Operation—Continued
About the Listening Modes
Dolby Pro Logic II Music
Use this mode to add 5.1 surround to stereo sources such
as music CDs and DVDs.
With its built-in surround-sound decoders and DSP pro-
grams, the AV receiver can transform your home listen-
ing room into a movie theater or concert hall.
Dolby Pro Logic IIx
If you connect two surround back speakers (i.e., left and
right), both will be used for 6.1-channel surround play-
back.
If you’ve connected surround back speakers to the AV
receiver, Dolby Pro Logic IIx allows you to enjoy 7.1-
channel playback from 2-channel or 5.1-channel music
or movies. Dolby Pro Logic IIx provides a well defined,
natural multichannel surround-sound experience, put-
ting the listener in a seamless envelope of sound. The
added drama and natural sound enhance the listening
experience with CDs, movies, and games.
The AV receiver’s surround indicators show which
speakers are active in each listening mode.
Front left
Center
Front right
Dolby Pro Logic IIx has three modes of operation:
Movie mode for movies, Music mode for listening to
music, and Game mode for use with games consoles
with 2-channel stereo outputs.
Subwoofer
Surround Surround Surround
left
back left/
right
right
Dolby Digital
Direct
With this format you can experience the
same superb sound that you get at a movie
theater or concert hall. Use this mode with DVDs that
bear the Dolby Digital logo.
The selected input source is output by the front left and
right speakers only, with minimal processing for a pure
sound.
Pure Audio
Dolby Digital EX
As an extension of Direct mode, this mode turns off the
display, turns off the power to the video circuitry, and
minimizes any other possible noise sources, providing a
high fidelity sound that’s true to the original. (Since the
power to the video circuitry is turned off, no video sig-
nals are output while this mode is selected.)
With an added surround-back channel,
this 6.1 channel format offers a heightened
sense of space, for added realism with moving sounds,
such as those that rotate 360 degrees or pass overhead.
Dolby Digital EX material can also be played on conven-
tional 5.1 channel systems, in which case the surround-
back channel audio is split between the surround left and
right channels. Use this mode with DVDs that have a
5.1-channel soundtrack and bear the Dolby Digital logo.
Stereo
The selected input source is processed as a stereo signal
and output by the front left and right speakers and the
subwoofer.
DTS
This digital surround format offers a sur-
round sound experience with exceptional
fidelity. It uses compressed digital audio
data, with six discrete channels (5.1), and the
ability to handle large amounts of audio data while
remaining faithful to the original. DTS provides very
high-quality sound.You’ll need a DTS compatible DVD
player in order to enjoy DTS material. Use this mode
with DVDs, LDs, or CDs that bear the DTS logo.
Mono
or
Use this mode when watching an old movie with a mono
soundtrack, or to select multilingual soundtracks
recorded in the left and right channels of some movies.
It can also be used when playing a DVD or other source
with multiplexed audio, such as a karaoke DVD.
T-D (Theater-Dimensional)
or
With this mode you can enjoy a virtual 5.1 surround
sound even with only two or three speakers. This works
by controlling how sounds reach the listener’s left and
right ears. Good results may not be possible if there’s too
much reverb, so we recommend that you use this mode
in an environment with little or no natural reverb.
DTS 96/24
This mode provides higher audio quality.
Use it with CDs, DVDs, and LDs that bear
the DTS 96/24 logo.
DTS-ES Discrete
Dolby Pro Logic II Movie
This is DTS with an added surround back
channel for 6.1 surround sound. Use it with
program material recorded in DTS 6.1 format. With the
additional surround back channel, this format offers 6.1
fully independent digital channels, providing a realistic
sense of movement and space. Use it with program mate-
rial recorded in DTS 6.1, such as CDs, DVDs, or LDs
that bear the DTS-ES logo.
Use this mode with DVDs and vid-
eos that bear the Dolby Surround
logo or TV programs that feature Dolby Surround. You
can also use this mode with stereo movies or TV pro-
grams and the AV receiver will create a 5.1 surround mix
from the 2-channel stereo.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 63 Tuesday, September 7, 2004 1:18 PM
Basic Operation—Continued
Onkyo Original DSP Modes
DTS-ES Matrix
This is DTS with an added surround back
channel for 6.1 surround sound. Use it to
provide 6.1 channel surround playback
with program material recorded in DTS 5.1
format. Since DTS 5.1 program material
contains surround back channel informa-
tion, all channels can be reconstructed for 6.1-channel
playback. Use this mode with CDs, DVDs, or LDs that
bear the DTS-ES or DTS logo.
Orchestra
or
Suitable for classical or operatic music. The center
speaker is turned off and the surround channels are
emphasized in order to widen the stereo image. In addi-
tion, it simulates the natural reverberation of a large hall.
Unplugged
Suitable for acoustic instrument sounds, vocals, and jazz
music. By emphasizing the front stereo image, it simu-
lates the stage-front experience.
Neo:6
This mode provides 6.1-channel playback from 2-chan-
nel sources. It offers six full-bandwidth channels with
excellent separation. There are two modes of operation:
Cinema mode for movies, and Music mode for listening
to music.
Studio-Mix
Suitable for rock and pop music. Listening to music in
this mode creates a lively sound field with a powerful
acoustic image, like being at a club or rock concert.
TV Logic
Cinema mode simulates the realistic sense of movement
that you get with 6.1-channel surround sound sources.
Use this mode with videos, DVDs, and TV programs that
feature stereo sound.
Adds realistic acoustics to TV programs produced in a
TV studio. In addition, it adds surround effects to the
entire sound and adds clarity to voices.
Enhance
Music mode uses the surround channels to simulate a
natural sound field that cannot be produced with conven-
tional stereo. Use this mode with stereo material such as
music CDs.
This mode is ideal for enjoying music programs or TV
sports programs. It provides a natural surround sound
with movement in the surround back speakers, creating
a sound with a live feeling to it.
THX Cinema (TX-SR702/702E only)
or
Mono Movie
THX Ltd, founded by George Lucas, develops quality
assurance programs for ensuring that movies are repro-
duced in movie theaters and home theaters just as the
director intended. THX technology is used to eliminate
spatial errors that can occur when a movie soundtrack is
adapted for use in smaller home theaters, ensuring faith-
ful reproduction.
This mode is suitable for use with old movies and other
mono sound sources. The center speaker outputs the
sound as it is, while reverb is applied to the sound output
by the other speakers, giving presence to even mono
material.
All Ch Stereo
Ideal for background music. The front, surround, and
surround back channels create a stereo image that fills
the entire listening area.
This mode is ideal for watching a movie with a
soundtrack recorded and edited especially for playback
in the spaciousness of a typical movie theater.
Full Mono
THX Surround EX (TX-SR702/702E only)
In this mode, all speakers output mono audio, so the
music sounds the same regardless of where you are.
THX Surround EX - Dolby Digital Surround EX is a
joint development of Dolby Laboratories and the THX
Ltd.
In a movie theater, film soundtracks that have been
encoded with Dolby Digital Surround EX technology
are able to reproduce an extra surround back channel
which has been added during the mixing of the program.
A list of Surround EX encoded movies can be found on
63
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 64 Tuesday, September 7, 2004 1:18 PM
Advanced Operation
Using the Re-EQ Function
(TX-SR702/702E only)
With the Re-EQ function, you can correct a soundtrack
whose high-frequency content is too harsh, making it
more suitable for home theater viewing. This function
can be used with the following listening modes: Dolby
Digital, Dolby Digital EX, Dolby Pro Logic IIx Movie,
DTS, DTS-ES, DTS Neo:6 Cinema, DTS 96/24,
DTS+Neo:6, and DTS+Dolby EX.
RECEIVER
Press the [RECEIVER] button fol-
lowed by the [Re-EQ] button.
1
RECEIVER
Press the button again to turn off the
Re-EQ function.
-
Re EQ
Re-EQ
L NIGHT
Notes:
• By default, the Re-EQ function is off.
Using the CinemaFILTER
(TX-SR602/602E, TX-SR8260 only)
CINE FLTR
With the CinemaFILTER, you can soften overly bright
movie soundtracks, which are typically mixed for repro-
duction in a movie theater.
(RC-570M, RC-591M)
CinemaFILTER can be used with the following listening
modes: Dolby Digital, Dolby Digital EX, Dolby Pro
Logic IIx Movie, DTS, DTS-ES, DTS Neo:6 Cinema,
DTS 96/24, DTS+Neo:6, and DTS+Dolby EX.
Using the Late Night Function
(Dolby Digital only)
With the Late Night function, you can reduce the
dynamic range of Dolby Digital material so that you can
still hear quiet parts even when listening at low volume
levels—ideal for watching movies late at night when you
don’t want to disturb anyone.
Press the [RECEIVER] button,
and then press the [CINE FLTR]
button repeatedly to select:
1
RECEIVER
On: CinemaFILTER on.
Off: CinemaFILTER off.
CINE FLTR
Press the [RECEIVER] button,
and then press the [L NIGHT] but-
1
RECEIVER
ton repeatedly to select:
Off: Late Night function off.
Low: Small reduction in dynamic
L NIGHT
range.
High: Big reduction in dynamic
range.
Notes:
• The effect of the Late Night function depends on the
Dolby Digital material that you are playing, and with
some material there will be little or no effect.
• The Late Night function is set to Off when the AV
receiver is set to Standby.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 65 Tuesday, September 7, 2004 1:18 PM
Advanced Operation—Continued
Using the DVD Analog Multichannel
Input
The DVD analog multichannel input is for connecting
components with a 5.1-channel analog audio output,
such as a DVD player or MPEG decoder.
See “Using a Multichannel Connection” on page 29 for
connection information.
MULTI CH
RECEIVER
Press the [RECEIVER] button fol-
lowed by the [MULTI CH] button
1
RECEIVER
so that “MCH” appears on the
display.
Notes:
• To use the bass and treble functions with the DVD
analog multichannel input, select the Multich listening
mode first.
CH SEL
LEVEL – +
Adjusting Individual Speaker Levels
You can adjust the level of individual speakers while
using the DVD analog multichannel input.
Adjusting Individual Speaker Levels
Use the remote controller’s [CH
SEL] button to select each
1
You can adjust the level of individual speakers during
playback. These adjustments are temporary and will be
cancelled when the AV receiver is set to Standby.
CH SEL
speaker, and then use the
[LEVEL–] and [LEVEL+] buttons
to adjust the volume.
Press the [RECEIVER] button,
use the [CH SEL] button to select
1
RECEIVER
The level can be adjusted from –12 to
+12 dB (–30 to +12 dB for the sub-
each speaker, and use the
[LEVEL–] and [LEVEL+] buttons
to adjust the volume.
-
+
LEVEL
LEVEL
woofer).
Speakers are selected in the following
CH SEL
order: Front Left → Center → Front
Right → Surr Right → Surr Back
Right → Surr Back Left → Surr left →
Subwoofer.
Notes:
• These speaker level settings are completely indepen-
dent of those explained on pages 50 and left column.
• While the DVD analog multichannel input is selected,
you can only select the Direct, Pure Audio (not Amer-
ican TX-SR602), or Multich listening mode. If you
select the DVD analog multichannel input while using
another listening mode, that listening mode will be
cancelled.
-
+
LEVEL
LEVEL
You can adjust the volume of each
speaker from –12 dB to +12 dB
(–15 dB to +12 dB for the subwoofer).
The name of the currently selected
speaker and its volume appear on the
display, as shown.
• While the DVD analog multichannel input is selected,
the Automatic Speaker Setup and Speaker Configura-
tion settings on page 46 are ignored, and signals from
the multichannel input are fed to the front left, front
right, center, surround left, and surround right speak-
ers, and subwoofer regardless of those settings.
• On the TX-SR702E, you can select the listening
modes as explained on page 61. In addition, sound is
output by the surround back speakers.
Notes:
• You cannot use this function while the AV receiver is
muted.
• Speakers that are set to No or None in the Speaker
Configuration cannot be adjusted.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 66 Tuesday, September 7, 2004 1:18 PM
Advanced Operation—Continued
Recording
Press the [REC OUT] button, and
2
then use the Controller [ ]/[
buttons to select “Rec Sel :
Source.”
]
This section explains how to record the current input
source, how to record one input source while enjoying
another, and how to dub audio onto your video record-
ings.
The current input source can be
recorded by the recorder connected to
the TAPE OUT.
Unless you have the full consent of the copyright
holder, copyright laws prohibit using your recordings
for anything other than personal enjoyment!
Notes:
• The surround sound and DSP listening modes cannot
be recorded.
Start recording on the recorder.
See your recorder’s manual for more
information.
3
4
• Copy-protected DVDs cannot be recorded.
• You cannot record from the DVD analog multichannel
input.
Start playback on the source
component.
If you select another input source dur-
ing recording, that input source will be
recorded.
• Various restrictions apply to digital recording. Refer to
the manuals supplied with your digital recording
equipment for more details.
• Digital input signals are output by only the digital out-
puts, and analog input signals are output by only the
analog outputs. There is no internal conversion from
digital to analog or vice versa.
Recording Audio & Watching a Separate
AV Source at the Same Time
• DTS signals will be recorded as noise, so don’t
attempt analog recording of DTS CDs or LDs.
While recording audio, you can watch a completely sep-
arate AV Source at the same time. For example, you
could watch a DVD while recording a CD to tape.
REC OUT
Press the [REC OUT] button.
1
Within five seconds, use the
2
Controller [ ]/[ ] buttons to
select the audio input source that
you want to record (you cannot
select TAPE).
Input Selector
Controller
The name of the input source selected
for recording appears on the display.
The specified input source can now be
recorded by the recorder connected to
the TAPE OUT.
Recording Audio
You can record the current audio source as follows.
Start recording on the recorder.
See your recorder’s manual for more
information.
Use the input selector buttons to
select the audio component that
you want to record.
3
1
Start playback on the audio
source component.
4
Notes:
• Since the Zone 2 function and the REC OUT outputs
use the same circuitry, you cannot record from a sepa-
rate source and use Zone 2 at the same time.
• To turn off the REC OUT output (i.e., the TAPE
OUT), press the [REC OUT] button, and then use the
Controller [ ] [ ] buttons to select “OFF.”
66
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 67 Tuesday, September 7, 2004 1:18 PM
Advanced Operation—Continued
AV Recording
Recording Separate AV Sources
You can record AV input sources to an AV recording
component (VCR, etc) connected to the VIDEO 1 OUT
or VIDEO 2 OUT. See pages 27–38 for information on
connecting components.
Here you can record audio and video from completely
separate sources, allowing you to overdub audio onto
your video recordings. This function takes advantage of
the fact that when an audio-only input source (i.e.,
TAPE, TUNER, or CD) is selected, the video input
source remains unchanged.
In the following example, audio from the CD player con-
nected to the CD IN, and video from the camcorder con-
nected to theVIDEO 4 INPUTVIDEO jack are recorded
by the VCR connected to the VIDEO 1 OUT jacks.
1
Camcorder
Use the input selector buttons to
select the AV component that
you want to record.
1
video signal
audio signal
Audio signals from the selected input
source are output by theVIDEO 1 OUT
and VIDEO 2 OUT only.
You can watch the source while record-
ing, and the AV receiver’s VOLUME
control has no effect on recording.
Start recording on the AV compo-
nent connected to the VIDEO 1
OUT or VIDEO 2 OUT.
2
Start playback on the source AV
component.
3
CD player
VCR
If you select another input source dur-
ing recording, that input source will be
recorded.
Prepare the camcorder and CD player for
playback.
1
Prepare the VCR for recording.
2
3
4
Press the [VIDEO 4] input selector button.
Press the [CD] input selector button.
This selects the CD player as the audio source, but
leaves the camcorder as the video source.
Start recording on the VCR and start play-
back on the camcorder and CD player.
The video from the camcorder and the audio from
the CD player are recorded by the VCR.
5
67
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 68 Tuesday, September 7, 2004 1:18 PM
Advanced Setup
3-1. Analog/PCM
Decoder Setup
These settings apply to PCM input signals from CD
players and so on, and analog signals from cassette play-
ers, turntables, and so on.
Here are surround-related settings for PCM, Dolby Dig-
ital, multichannel, and other input signal formats.
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
■ a. Input Channel (Mono)
1
RECEIVER
This setting determines which channel is output when
the Mono listening mode is used with a stereo source.
L+R: Both the left and right channels are output
(default).
Left: Only the left channel is output.
Right: Only the right channel is output.
■ b. Surround Mode
This setting determines the surround mode for analog
and PCM input signals. This setting is unavailable if no
center and surround speakers are connected.
You can select PLIIx Movie (default), PLIIx Music,
PLIIx Game, Neo:6 Cinema, or Neo:6 Music.
Use the Up and Down [ ]/[
buttons to select “3. Decoder
Setup,” and then press [ENTER].
]
2
ENTER
The Surround Setup menu appears.
■ c.THX Mode (TX-SR702/702E only)
This setting determines which surround mode is used
when THX is used with analog and PCM input signals.
This setting is unavailable if no surround speakers are
connected.
Menu
------------------------
3.Decorder Setup
ENTER
------------------------
1.Analog/PCM
2.Dolby Digital
3.DTS
4.D.F.2ch
5.Multiplex
You can select either PLIIx+THX (default) or
Neo:6+THX.
6.Multich Input
Use the Up and Down [ ]/[
buttons to select the menu items,
and then press [ENTER].
]
3
4
If you’re not using any surround back speakers, “PLIIx”
will be “PLII.”
If you’re not using any surround speakers, Neo:6 Music
cannot be selected.
ENTER
ENTER
3-2. Dolby Digital
These settings apply to Dolby Digital input signals.
■ a. LFE Level
With this setting, you can set the level of the LFE (Low
Use the Up and Down [ ]/[
buttons to select the settings,
and use the Left and Right [ ]/
]
F–∞req,u–e1n0cydBE,ffoerc0ts)dcBh(adnenfealuflot)r.Dolby Digital sources to
If you find that the low-frequency effects are too loud
when playing Dolby Digital sources, set this to –10 dB
or –∞ dB.
ENTER
[
] buttons to set them.
The settings are explained below.
■ b. Dolby EX
This setting determines how Dolby Digital EX signals
are handled. This setting is unavailable if no surround
back speakers are connected.
Auto: If the source signal contains a Dolby Digital
EX flag, the Dolby Digital EX listening mode
is used.
When you’ve finished, press the
[SETUP] button.
The setup menu closes.
5
Manual:Depends on the c. SurrBack Mode setting and
d. THX Mode setting.
Note:
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
6_Advnced_En Page 69 Tuesday, September 7, 2004 3:05 PM
Advanced Setup—Continued
■ c. SurrBack Mode
L+R: Both the left and right channels are output
(default).
Left: Only the left channel is output.
Right: Only the right channel is output.
This setting determines which surround mode is used for
Dolby Digital input signals that don’t contain a Dolby
Digital EX flag, or when the b. Dolby EX setting is set to
Manual. This setting is unavailable if no surround back
speakers are connected.
■ b. Surround Mode
This setting determines the default surround mode for
digital input signals, Dolby Digital and so on, with only
2 channels (2/0). This setting is unavailable if no center
and surround speakers are connected.
You can select PLIIx Movie (default), PLIIx Music,
PLIIx Game, Neo:6 Cinema, or Neo:6 Music.
You can select PLIIx Movie (default), PLIIx Music, or
Dolby D, or Dolby D EX.
• If only one surround back speaker is connected, PLIIx
Movie is unavailable.
■ d.THX Mode (TX-SR702/702E only)
This setting determines which surround mode is used
when THX is used with Dolby Digital input signals. This
setting is unavailable if no surround back speakers are
connected. (The THX Cinema is determined automati-
cally.)
You can select THX SurrEX (default), PLIIx+THX, or
THX Cinema.
• If only one surround back speaker is connected,
PLIIx+THX is unavailable.
3-5. Multiplex
This setting applies to multiplex input signals.
■ a. Input Channel
This setting determines which channel is output from a
stereo multiplex source. Use it to select audio channels
or languages with multiplex sources, multilanguage TV
broadcasts, and so on.
Main: The main channel is output (default).
Sub: The sub channel is output.
3-3. DTS
Main/Sub:Both the main and sub channels are output.
These settings apply to DTS input signals.
■ a. LFE Level
3-6. Multichannel Input
With this setting you can set the level of the LFE (Low
Frequency Effects) channel for DTS sources to –∞,
–10 dB, or 0 dB (default).
If you find that the low-frequency effects are too loud
when playing DTS sources, set this to –10 dB or –∞ dB.
These settings apply to the analog multichannel input.
■ a. Subwoofer Sensitivity
When using the DVD analog multichannel input, the
loudness of the connected subwoofer also depends on
the component that’s connected to that input. If you find
that it’s too loud, set this to 0 dB, +5 dB, +10 dB, or
+15 dB. The default setting is 0 dB.
■ b. SurrBack Mode
This setting determines which surround mode is used for
DTS input signals that are not DTS-ES. (The handling of
DTS-ES input signals is determined automatically.) This
setting is unavailable if no surround back speakers are
connected.
■ b. SurrBack Mode (TX-SR702E only)
If you’re using surround back speakers, this setting
determines which surround mode is used with analog
multichannel input signals. This setting is unavailable if
no surround back speakers are connected.
You can select DTS+Neo:6 (default), Dolby EX, PLIIx
Movie, PLIIx Music, or DTS.
• If only one surround back speaker is connected, PLIIx
Movie is unavailable.
You can select Dolby EX, PLIIx Movie (default), PLIIx
Music, or Multich (straight 5.1-channel playback).
• If only one surround back speaker is connected, PLIIx
Movie is unavailable.
■ c.THX Mode (TX-SR702/702E only)
This setting determines which surround mode is used
when THX is used with DTS input signals. This setting
is unavailable if no surround back speakers are con-
nected. (The THX Cinema is determined automatically.)
You can select THX SurrEX, Neo:6+THX (default),
PLIIx+THX, or THX Cinema.
■ c.THX Mode (TX-SR702E only)
This setting determines which surround mode is used
when THX is used with analog multichannel input sig-
nals. This setting is unavailable if no surround back
speakers are connected. (The THX Cinema is deter-
mined automatically.)
You can select THX SurrEX (default), PLIIx+THX, or
THX Cinema.
• If only one surround back speaker is connected,
PLIIx+THX is unavailable.
• If only one surround back speaker is connected,
PLIIx+THX is unavailable.
3-4. D.F. 2ch
These settings apply to digital input signals, Dolby Dig-
ital and so on, with only 2 channels (2/0).
If you’re not using any surround back speakers, “PLIIx”
will be “PLII.”
■ a. Input Channel (Mono)
If you’re not using any surround speakers, Neo:6 Music
cannot be selected.
This setting determines which channel is output when
the Mono listening mode is used with a stereo source.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 70 Tuesday, September 7, 2004 1:18 PM
Advanced Setup—Continued
Adjusting the Bass & Treble
Audio Adjust Functions
You can adjust the bass and treble for the front speakers,
except when the Direct, Pure Audio (not American
TX-SR602), or THX listening mode is selected.
Here you can set listening mode-related settings and
functions.
Press the [RECEIVER] button fol-
1
RECEIVER
lowed by the [SETUP] button.
The main menu appears onscreen.
Use the Up and Down [ ]/[
buttons to select “4. Audio
Adjust,” and then press [ENTER].
]
2
3
1 2
ENTER
The Audio Adjust menu appears.
Press the [TONE] button repeat-
edly to select either Bass or
Treble.
1
ENTER
Use the TONE [–]/[+] buttons to
adjust.
2
Use the Up and Down [ ]/[
buttons to select menu items,
and then press [ENTER].
]
ENTER
Menu
------------------------
B
4.Audio Adjust
------------------------
1.Mono
ENTER
2.PL x/Neo:6
■ Bass
3.Enhance
4.Orchestra
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 2 dB steps.
5.Unplugged
6.Studio-Mix
7.TV Logic
8.Mono Movie
9.Theater-Dimensional
■ Treble
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10 dB in 2 dB steps.
Use the Up and Down [ ]/[
buttons to select the settings,
]
4
ENTER
and use the Left and Right [ ]/
[
] buttons to set them.
The settings are explained below.
When you’ve finished, press the
[SETUP] button.
5
The setup menu closes.
Note:
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 71 Tuesday, September 7, 2004 1:18 PM
Advanced Setup—Continued
of the center channel sound. It can be adjusted from 0 to
7 (default is 3).
4-1. Mono
■ a. Output Channel
■ d. Center Image
This setting determines which speakers are used to out-
put mono audio when the Mono listening mode is used.
L/R: Mono audio is output from the front left and
right speakers (default).
The DTS Neo:6 Music listening mode creates 6-channel
surround sound from 2-channel (stereo) sources. With
this setting, you can specify by how much the front left
and right channel output is attenuated in order to create
the center channel. It can be adjusted from 0 to 5 (default
is 3).
Center: Mono audio is output from the center speaker.
■ b. Academy (TX-SR702/702E only)
When set to 0, the front left and right channel output is
attenuated by half (–6 dB), giving the impression that the
sound is located centrally. This setting works well when
the listening position is considerably off center. When
set to 5, the front left and right channels are not attenu-
ated, maintaining the original stereo balance.
Early movies had a mono soundtrack that suffered from
audible hiss and a poor high-frequency response due to
the quality of the film. To improve matters, the high-fre-
quencies were boosted before being recorded onto film,
and then attenuated to their original levels during play-
back in the movie theater. Some old movies have been
transferred to newer distribution media without the high
frequencies being attenuated, creating a harsh sound
with pronounced hiss. With theAcademy Filter, which is
based on the playback techniques used in those days, you
can attenuate those high-frequencies to their original lev-
els and enjoy the movie as it was intended to be heard.
On: Academy Filter on.
4-3. Enhance, 4-4. Orchestra, 4-5.
Unplugged, 4-6. Studio-Mix, 4-7.TV Logic
& 4-8. Mono Movie
These settings apply to the Onkyo original DSP listening
modes.
■ a. Front Effect
Off: Academy Filter off (default).
With this setting, you can turn off the reverb for the front
speakers. This is useful when playing live material that
already contains live reverberation and the reverb added
by the DSP listening mode simply blurs the original
sound. When the Front Effect is turned off, no reverb is
added to the front left, right, and center speakers and the
original reverberation can be heard as it is.
On: Front Effect on (default).
4-2. PLIIx/Neo:6
If no surround back speakers are connected, this item
will be “PLII/Neo:6” instead of “PLIIx/Neo:6.”
■ a. Panorama
With this function, you can broaden the width of the
front stereo image when using the Dolby Pro Logic IIx
Music listening mode.
Off: Front Effect off.
On: Panorama function on.
Off: Panorama function off (default).
■ b. Reverb Level
With this setting, you can adjust the amount of reverb to
suit your listening environment, source material, and so
on. The available settings are: Low, Middle (default),
and High.
■ b. Dimension
With this setting, you can move the sound field forward
or backward when using the Dolby Pro Logic IIx Music
listening mode. The default setting is 3. Higher settings
move the sound field forward. Lower settings move it
backward.
If the stereo image feels too wide, or there’s too much
surround sound, move the sound field forward to
improve the balance. Conversely, if the stereo image
feels like it’s in mono, or there’s not enough surround
sound, move it backward.
■ c. Reverb Time
With this setting, you can adjust the reverb time to suit
your listening environment, source material, and so on.
The available settings are: Short, Middle (default), and
Long.
■ c. Center Width
With this function, you can adjust the width of the sound
from the center speaker when using the Dolby Pro Logic
IIx Music listening mode. If you’re using a center
speaker, with Dolby Pro Logic IIx, the center channel
sound is output by only the center speaker. (If you’re not
using a center speaker, the center channel sound will be
distributed to the front left and right speakers to create a
phantom center). This setting controls the front left,
right, and center mix, allowing you to adjust the weight
71
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 72 Tuesday, September 7, 2004 1:18 PM
Advanced Setup—Continued
4-9.Theater-Dimensional
Assigning Listening Modes to Input
Sources
These settings apply to the Theater-Dimensional listen-
ing mode.
You can assign a default listening mode to each input
source that will be selected automatically when you
select each input source. For example, you can set the
default listening mode to be used with Dolby Digital
input signals. You can select other listening modes dur-
ing playback, but the mode specified here will be
resumed once the AV receiver has been set to Standby.
■ a. Listening Angle
With this setting, you can specify the angle of the front
left and right speakers relative to the listening position.
Processing for the Theater-Dimensional listening mode
is based on this setting. Ideally, the front left and right
speakers should be equidistant from the listening posi-
tion and at an angle close to one of the two available set-
tings.
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
1
RECEIVER
Front left speaker
Front right speaker
The main menu appears onscreen.
20/40˚
Use the Up and Down [ ]/[
]
20º: Select if the listening angle is 20 degrees.
40º: Select if the listening angle is 40 degrees
(default).
2
buttons to select “5. Listening
Mode Preset,” and then press
[ENTER].
The Listening Mode Preset menu
appears.
ENTER
■ b. Center
With this setting, you can specify whether or not you’re
using a center speaker. If you are, the center channel
sound will be output by the center speaker when using
the Theater-Dimensional listening mode. This reduces
the workload of the front left and right speakers, and cre-
ates a more articulate sound space. In this case, the set-
tings for the distance between the listening position and
each speaker, and the level of each speaker are impor-
tant, but making these settings is a breeze with the Auto-
matic Speaker Setup function (see page 39).
ENTER
Menu
------------------------
B
5.Listening Mode Preset
------------------------
1.DVD/MULTICH
2.VIDEO1
3.VIDEO2
4.VIDEO3
5.VIDEO4
6.TAPE
7.TUNER
8.CD
9.PHONO
On: Select if using a center speaker.
Off: Select if not using a center speaker (default).
Use the Up and Down [ ]/[
]
3
buttons to select the input selec-
tor that you want to set, and then
press [ENTER].
■ c. Front Expand
ENTER
With the Front Expander function, you can broaden the
width of the front stereo image. This can be useful with
narrow listening angles of 20 degrees or less.
On: Front Expander function on.
5-1.ListeningModePreset
----- DVD/MULTICH ------
a.Ana/PCM :Last Valid
Off: Front Expander function off (default).
b.Dolby D :Last Valid
ENTER
c.DTS
:Last Valid
d.D.F.2ch :Last Valid
e.d.f.Mono:Last Valid
f.Multiplex
:Last Valid
g.Multich :Last Valid
■ d. Dialog Enhance
With this function, you can improve the clarity of the
center channel, which usually contains dialog.
On: Dialog Enhance function on.
Off: Dialog Enhance function off (default).
For input selectors that have no digital
input jacks, only “a. Analog” will be
available.
■ e. Virtual Surr Level
With this setting, you can adjust the level of virtual sur-
round sound from –3 dB to +3 dB (default is 0 dB). If the
clarity is poor, or the effect sounds unnatural, you may
be able to improve it by lowering this setting.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 73 Tuesday, September 7, 2004 1:18 PM
Advanced Setup—Continued
Note:
Use the Up and Down [ ]/[
]
4
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
buttons to select the signal for-
mat that you want to set, and
then use the Left and Right [ ]/
ENTER
[
] buttons to select a listening
mode.
Only listening modes that can be used
with each input signal format can be
selected.
For “Surround” or “THX,” the listening
mode specified on pages 68, 69 will be
used.
The Last Valid option means that the
listening mode selected last will be
used.
a. Ana/PCM: With this setting, you
can specify the listening mode to be
used when an analog (CD, TV, LD,
VHS, MD, turntable, radio, cassette,
cable, satellite, etc) or PCM digital
(CD, DVD, etc) audio signal is played.
b. Dolby D: With this setting, you can
specify the listening mode to be used
when a Dolby Digital format digital
audio signal is played (DVD, etc).
c. DTS: With this setting, you can spec-
ify the listening mode to be used when
a DTS format digital audio signal is
played (DVD, LD, CD, etc).
d. D.F. 2ch: With this setting, you can
specify the listening mode to be used
when a 2-channel (2/0) digital audio
signal (Dolby Digital, DTS) is played
(DVD, etc).
e. D.F. Mono: With this setting, you
can specify the listening mode to be
used when a mono digital audio signal
is played (DVD, etc).
f. Multiplex: With this setting, you can
specify the listening mode to be used
when a multiplex audio signal is
played.
g. Multich: This setting is available
only when “5-1. DVD/MULTCH” is
selected. With this setting, you can
specify the listening mode to be used
when the DVD analog multichannel
input is used.
When you’ve finished, press the
[SETUP] button.
5
The setup menu closes.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 74 Tuesday, September 7, 2004 1:18 PM
Advanced Setup—Continued
6-1. IntelliVolume
Setting Preferences
With this preference, you can set the input level for each
input source. This is useful if some of your AV compo-
nents are louder or quieter than others.
While this preference is shown onscreen, you can select
each input source and set the levels while listening to and
comparing them.
This section explains the items on the Preference menu.
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
1
RECEIVER
The main menu appears onscreen.
If a component is too loud compared to your other com-
ponents, use the Left [ ] button to adjust the level. If it’s
too quiet, use the Right [ ] button.
• The level can be set from –12 dB to +12 dB.
Use the Up and Down [ ]/[
buttons to select “6. Preference,”
and then press [ENTER].
]
6-2. Volume Setup
2
ENTER
■ a. Volume Display
With this preference, you can choose how the volume
The Preference menu appears.
level is displayed.
Menu
Absolute:Display range is MIN, 1 through 99, MAX.
Relative:Display range is –∞ dB, –81 dB, –80 dB
through +18 dB.
The absolute value 82 is equivalent to the relative value
0 dB.
------------------------
B
6.Preference
ENTER
------------------------
1.IntelliVolume
2.Volume Setup
3.OSD Setup
4.Remote Setup
5.Digital Format
■ b. Maximum Volume
With this preference, you can prevent the volume being
set too high by specifying a maximum volume level.
When the Volume Display preference is set to Absolute,
the range is from 50 to 99. When it’s set to Relative, the
range is –32 dB through +17 dB. To specify no maxi-
mum volume, select Off.
Use the Up and Down [ ]/[
buttons to select menu items,
and then press [ENTER].
]
3
4
ENTER
■ c. Power On Volume
With this preference, you can specify the volume setting
to be used each time the AV receiver is turned on.
When the a. Volume Display preference is set to Abso-
lute, the range is MIN, 1 through 99, or MAX. When it’s
set to Relative, the range is –∞ dB, –81 dB through
+18 dB.
To use the same volume level that was used when the AV
receiver was turned off, select Last.
The Power On Volume cannot be set higher than the
maximum volume specified with the b. Maximum Vol-
ume setting.
ENTER
Use the Up and Down [ ]/[
buttons to select the settings,
and use the Left and Right [ ]/
]
ENTER
[
] buttons to set them.
The settings are explained below.
■ d. Headphones Level
With this preference, you can specify the headphone vol-
ume relative to the main volume. This is useful if there’s
a volume difference between your speakers and your
headphones. The headphone volume can be set between
–12 dB and +12 dB.
When you’ve finished, press the
[SETUP] button.
The setup menu closes.
5
Note:
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 75 Tuesday, September 7, 2004 1:18 PM
Advanced Setup—Continued
receiver is identifying the DTS signal, or when
using fast forward or fast reverse. Nothing is
output if the input signal is not DTS.
6-3. OSD Setup
■ a. Immediate Display
This preference determines whether or not actions, such
as selecting an input source, are displayed onscreen.
Normal: Select if your TV is 4:3.
PCM: Select this option if playing a CD or other PCM
source with the Auto option causes the tops of
tracks to be clipped. Nothing is output if the
input signal is not PCM.
Wide: Select if your TV is 16:9.
• If there is no digital connection, only Auto appears.
• SelectAuto or DTS when playing a DTS CD or LD. If
you select PCM, only noise will be heard.
Off: Actions not displayed.
Even if this preference is set to Normal or Wide, actions
are not displayed on the TV or projector that’s connected
to the COMPONENT VIDEO OUT.
■ b. Scan Mode
If the text in onscreen setup menus flickers due to com-
patibility with the connected display device (TV, projec-
tor, etc), set the Scan Mode to Non-Interlaced.
Interlaced:Default.
Non-Interlaced:Select if the text flickers.
• Depending on the display device, when Non-Inter-
laced is selected, the onscreen setup menus may not
appear. If this happens, use the AV receiver’s display
and repeat the procedure to revert to Interlaced.
Changing the Remote Controller’s ID
If several Onkyo components are used in the same room,
the remote controller’s control codes may overlap with
those of another component. To differentiate the remote
controller’s control codes, you can change its ID to
another number.
Notes:
If you change the remote controller’s ID, be sure to set
the same ID on both the remote controller and AV
receiver (see 6-4. Remote Setup in the left column). The
default ID for both is 1.
6-4. Remote Setup
■ a. Remote ID
With this setting, you can change the AV Receiver’s
remote control ID. You may need to change this if the
remote controller’s control codes overlap with those of
another Onkyo component located in the same room.
• If you change the AV receiver’s remote control ID, be
sure to set the same ID on both the AV receiver and
remote controller (see right column). The default ID
for both is 1.
1
Number
buttons
■ b. IR IN Position
When using a commercially available IR receiver, use
this setting to specify its location.
Main: Select if the IR receiver is located in the main
room.
1
Zone 2: Select if the IR receiver is located in, and will
be used to control Zone 2.
Press and hold down the [RECEIVER]
button, and then press the TV [INPUT]
button.
1
6-5. Digital Format
This setting does not apply to input selectors not
assigned to a digital input jack.
With this setting, you can set a digital input to DTS,
PCM, or Auto. This can be set for each input selector
individually.
Use the number buttons to enter a remote
control ID.
You can enter 1, 2, or 3.
2
Use the Up and Down [ ]/[ ] buttons to select the
input selector that you want to set, and then use the Left
and Right [ ]/[ ] buttons to select:
Auto: PCM, Dolby Digital, and DTS formats are
accepted. If no digital signal is present, the ana-
log input is used.
DTS: Select this option if playing a DTS CD with the
Auto option produces noise while the AV
75
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 76 Tuesday, September 7, 2004 1:18 PM
Zone 2
Using Only Speakers in Zone 2
Connecting Zone 2
With this connection method, you can use 5.1 surround
sound in the main room and play a differentAV source in
Zone 2. The volume for Zone 2 is set on the AV receiver.
With the Zone 2 function, you can enjoy one input
source in the main room and a different source in another
room.
There are two connection methods: using a receiver/inte-
grated amp in Zone 2 or using only a pair of speakers in
Zone 2.
• Set the Powered Zone 2 setting to Activated (see
page 77).
• Connect your Zone 2 speakers to the AV receiver’s
ZONE 2 SPEAKERS terminals.
Using a Receiver/Integrated Amp in Zone 2
Main room
With this connection method, you can use 7.1 surround
sound in the main room and play a differentAV source in
Zone 2. The volume for Zone 2 is set on the receiver/
integrated amp.
• Use an RCA audio cable to connect the AV receiver’s
ZONE 2 LINE OUT L/R jacks to an analog audio
input on your receiver/integrated amp.
TV
AV receiver
• Connect the Zone 2 speakers to the speaker terminals
on the receiver/integrated amp.
Main room
TV
Zone 2
AV receiver
L
R
Zone 2
IN
TV
R
L
Receiver/
integrated amp
76
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 77 Tuesday, September 7, 2004 1:18 PM
Zone 2—Continued
Setting the Powered Zone 2
Use the Up and Down [ ]/[
buttons to select “a. Powered
Zone 2,” and use the Left and
]
4
To use Zone 2, you must make this setting. It enables the
speakers connected to the ZONE 2 SPEAKERS termi-
nals so that they produce sound when Zone 2 is used.
ENTER
Right [ ]/[ ] buttons to select:
Menu
------------------------
1.Initial Setup
------------------------
1-3.Hardware Setup
------------------------
1
a.PoweredZone2
:Not Activated
b.Sp Impedance Minimum
:6ohms
2, 3
Not Activated: Zone 2 SPEAKERS
terminals deactivated.
2–4
Activated: Zone 2 SPEAKERS termi-
nals activated.
1, 5
When Zone 2 is activated and turned on
(see page 78), the speakers connected
to the ZONE 2 SPEAKERS terminals
output sound, but the speakers con-
nected to the SURROUND BACK
SPEAKERS terminals do not. (When
Zone 2 is activated but not used, the
surround back speakers work as nor-
mal.)
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
Press the [SETUP] button.
The setup menu closes.
1
2
RECEIVER
5
Note:
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
Use the Up and Down [ ]/[
buttons to select “1. Initial
]
ENTER
Setup,” and then press [ENTER].
The Initial Setup menu appears.
ENTER
Use the Up and Down [ ]/[
]
3
buttons to select “3. Hardware
Setup,” and then press [ENTER].
The Hardware Setup menu appears.
ENTER
ENTER
77
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 78 Tuesday, September 7, 2004 1:18 PM
Zone 2—Continued
To set Zone 2 to the same source as the
main room, press the [ZONE 2] button,
Using Zone 2
Here you can turn on Zone 2, select an input source, and
adjust the volume.
and then use the Controller [ ]/[
]
buttons to select “Zone 2 Sel: Source.”
To adjust the Zone 2 volume with
the remote controller, press the
[ZONE 2] button, and then use
the [LEVEL–] and [LEVEL+] but-
tons.
3
ZONE 2
4
1
2
-
+
LEVEL
LEVEL
To do this on the AV receiver,
press the ZONE 2 [LEVEL] but-
ton, and then use the Controller
1–4
[
]/[ ] buttons.
If the Zone 2 receiver/integrated amp is
connected to the AV receiver’s ZONE 2
LINE OUT L/R jacks, use the volume
control on the receiver/integrated amp.
To turn off Zone 2 with the
remote controller, press the
[ZONE 2] button followed by the
[STANDBY] button.
4
3
ZONE 2
STANDBY
To do this from the AV receiver,
press the [ZONE 2] button, and
Note:
To control Zone 2 with the remote controller, you must
press the [ZONE 2] button first.
then use the Controller [ ]/[
buttons to select OFF.
]
Point the remote controller at the
1
ZONE 2
Notes:
AV receiver and press the
[ZONE 2] button followed by the
[ON] button.
This turns on Zone 2 and the AV
receiver’s 12V TRIGGER OUT.
• If the Sleep function has been set, the Zone 2 compo-
nent will turn off along with the AV receiver when the
specified sleep time expires. To use the Sleep function
with Zone 2 only, set the Sleep function and then set
the AV receiver to Standby.
ON
• Only analog input sources are output by the ZONE 2
LINE OUT and ZONE 2 SPEAKERS terminals. Dig-
ital input sources are not output. If no sound is heard
when an input source is selected, check if it’s con-
nected to an analog input.
To select the Zone 2 input source
with the remote controller, press
the [ZONE 2] button followed by
2
ZONE 2
an input selector button.
If you select AM or FM, you can use
the remote controller’s [TUNER] but-
ton to select the band.
To perform steps 1 and 2 on the
AV receiver, press the [ZONE 2]
button, and then use the Control-
ler [ ]/[ ] buttons within five
seconds.
• Since the Zone 2 function and the REC OUT outputs
use the same circuitry, if the [REC OUT] function is
used, Zone 2 will be turned off.
• While Zone 2 is being used, listening modes that need
surround back speakers (i.e., Dolby Digital EX, DTS-
ES, and THX Surround EX) are unavailable.
• While Zone 2 is on,
functions will not work.
• You can’t select different radio stations for Zone 2 and
the main room. For example, if you an FM station for
the main room, that station will also be used in Zone 2.
The name of the selected Zone 2 source
appears on the display.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 79 Tuesday, September 7, 2004 1:18 PM
Zone 2—Continued
Using the 12V Trigger
Using a Multiroom Kit with a Cabinet
When Zone 2 is turned on, the ZONE 2 12V TRIGGER
OUT outputs 12 volts (100 milliamperes max). By con-
necting this jack to the 12-volt trigger input on, say, a
power amp in Zone 2, that power amp will turn on and
off automatically as and when Zone 2 is turned on and
off on the AV receiver.
In the following diagram, an IR receiver picks up the
infrared signals from the remote controller and feeds
them to the AV receiver in the cabinet via the connecting
block.
• On the Remote Setup menu, set the IR IN Position set-
ting to “Main” (see page 75).
Using the Remote Control in Zone 2
IR Receiver
To use the remote controller to control the AV receiver
from Zone 2, you’ll need one of the following commer-
cially available multiroom remote control kits:
• Multiroom Kits such as those made by Niles and Xan-
tech.
Connecting
block
IR IN
These kits can also be used when the AV receiver is not
in line of sight of the remote controller, for example,
when it’s installed inside a cabinet.
Inside
cabinet
Remote controller
Signal flow
Using a Multiroom Kit with Zone 2
In the following diagram, an IR receiver picks up the
infrared signals from the remote controller in Zone 2 and
feeds them to the AV receiver in the main room via the
connecting block.
• On the Remote Setup menu, set the IR IN Position set-
ting to “Zone 2” (see page 75).
IR Receiver
Connecting
block
Remote controller
Main room
Zone 2
Signal flow
Connect the miniplug cable from the connecting block to
the AV receiver’s IR IN jack as shown below.
from the connecting block
Miniplug cable
79
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 80 Tuesday, September 7, 2004 1:18 PM
Controlling Other Components
You can use the AV Receiver’s remote controller (RC-
588M/RC-590M/RC-591M) to control your other com-
While holding down the REMOTE
MODE button that you want to
enter the code for, press the
[STANDBY] button.
2
ponents, including those made by other manufacturers.
This chapter explains how to:
• Enter the remote control code for a component that
you want to control (e.g., DVD, TV, VCR).
• Learn commands directly from another component’s
remote controller (see page 88).
STANDBY
• Program the Macro function to perform a sequence of
actions with a single press of a button (see page 89).
Entering Remote Control Codes
Within 30 seconds, use the num-
ber buttons to enter the 4-digit
remote control code.
Entering the appropriate remote control code for each
REMOTE MODE button will allow you to control your
other components with the remote controller.You’ll need
to perform this procedure for each component that you
want to control.
For the [DVD], [TV], [VCR], [CABLE], and [SAT] but-
tons, choose a code from the respective category. For the
[CD] and [MD/CDR] buttons, you can choose a code
from any category. Remote control codes cannot be
entered for the [RECEIVER] and [ZONE 2] buttons.
3
4
Select the remote controller
mode, point the remote control-
ler at the component, and check
its operation.
2
3
Remote controller buttons that can be
used in DVD mode are shown on
page 16. Those that can be used with
the TV, VCR, CABLE, and SAT modes
are shown on pages 86, 87.
If the remote controller works OK, the code has been
entered correctly. If not, try again or try another code.
2
Codes for Onkyo DVD Players
The remote control code for an Onkyo DVD player
depends on whether it’s connected via
, as follows:
5001: Use this code if you’ve connected an
cable
and an analog audio cable to your DVD player.
This is the default setting, so if you’re using
, you don’t need to change anything. Point
the remote controller at the AV receiver to
operate the DVD player.
5002: Use this code if your DVD player doesn’t have
Look up the remote control code
1
an
jack, or you’re not using
. Point the
for your component.
See “Remote Control Codes” on
page 82.
remote controller at the DVD player to operate
it.
Setting the [MD/CDR] Button to CDR
By default, the [MD/CDR] button is set to control a
MiniDisc recorder. To control a CD recorder, it must be
set to CDR. The codes are as follows:
6002: Code for controlling an CD recorder.
6003: Code for controlling an MD recorder (default).
80
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 81 Tuesday, September 7, 2004 1:18 PM
Controlling Other Components—Continued
Resetting the Remote Controller
Here you can reset the remote controller to its default
settings.
STANDBY
TV
While holding down the
[RECEIVER] button, press the
1
RECEIVER
[STANDBY] button.
Release both buttons and wait five sec-
STANDBY
onds.
RECEIVER
REMOTE
MODE
Press the [RECEIVER] button
again.
2
RECEIVER
The remote controller is reset.
Resetting REMOTE MODE Buttons
If you’ve entered another code for one of these button
and now want to return to the default, perform the fol-
lowing procedure.
By default, some REMOTE MODE buttons are prepro-
grammed with remote control codes for controlling
Onkyo components connected via
.
While holding down the REMOTE
MODE button that you want to
1
reset, press the TV [
] button.
Release both buttons and wait two sec-
onds.
Press the REMOTE MODE button
again.
2
The REMOTE MODE button is reset.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 82 Tuesday, September 7, 2004 1:18 PM
Controlling Other Components—Continued
Remote Control Codes
SAT (satellite receiver)
SAT (satellite receiver)
Manufacturer
Conrad
Cosat
Control code
Manufacturer
Control code
When two or more codes are given,
try each one in turn, and choose the
one that works best.
Depending on the manufacturer and
component, the remote controller
may not work as expected.
4024
Nikko
4013, 4025, 4027
4033
4015, 4023
4013
Nokia
Crown
Nordmende
Oceanic
Octagon
Okano
4017, 4020
4022
Daewoo
Diamond
Dishnet
Dual
4016, 4017, 4025
4022
4016, 4017
4013
4008
4016
Optex
4015, 4023
4016
DVD (DVD player)
Echostar
Einhell
Elta
4010, 4018, 4025
4013, 4017, 4025
4015, 4017
4025
Orbit
Orbitech
Pace
4017, 4019
4012, 4026, 4031
4022
Manufacturer
Control code
Aiwa
5010
Engel
Pacific
Akai
5019
Eurosat
Eurosky
Eurostar
Fagor
4013, 4022
4013, 4024
4024
Palladium
Palsat
4013, 4017, 4021
4019
Apex
5015, 5016
5027
CyberHome
Denon
Panasonic
Panda
4006, 4031
4024
5017, 5020
5003
4015, 4023
4012
GE
Ferguson
Fidelity
Fracarro
FTE
Philips
4021, 4029
4015, 4023
4017
Hitachi
5009
4030
Phonotrend
Predki
Integra
5001, 5002
5001, 5002
5023
4017
Integra Research
JVC
4025, 4030
4017
Premier
Primestar
Proscan
Protek
4023
Fuba
4007
Kenwood
Magnavox
Marantz
Mitsubishi
Onkyo
5017
Galaxis
GE
4015, 4023
4001, 4002
4001, 4002
4022
5004, 5021
5025, 5026
5005
General Instruments 4003
Pye
4021
GMI
4013
Quelle
4024
5001, 5002
5011, 5017, 5020
5004, 5021, 5028
5006
Grundig
Hinari
4021, 4029, 4031
4017
Radix
4035
Panasonic
Philips
RCA
4001, 4002
4025
Hirschmann
Hitachi
4019, 4035
4036, 4037
Roadster
Rover
Pioneer
Proscan
RCA
4025
5003
Hughes Network
Systems
Saba
4014, 4020, 4024, 4027
4017
5003
4011
Samsung
Satcom
SatPartner
Schneider
Sedea Electronique
Seemann
SEG
Sanyo
5012
Huth
4013, 4015, 4024
4024
5007, 5013, 5018,
5029
Sony
Imperial
Intertronic
Intervision
Johansson
JVC
4014
4017, 4020, 4027, 4030
4029
4013
Technics
Thomson
Toshiba
Xbox
5020
4015, 4023, 4024
5022, 5024
5008, 5021
5022
4017
4015
4013
4009, 4021
4017, 4028
4015, 4023
4025, 4034
4015
Kathrein
Kolon
4025
Yamaha
Zenith
5020
Seleco
4017
5014, 5021
Skymaster
Skyvision
Sony
K-SAT
4025
Kyostar
Lasat
4017
SAT (satellite receiver)
Manufacturer
4005, 4031
4016, 4017, 4020
4013, 4020, 4024
Control code
Strong
Lenco
4016, 4017, 4025
Alba
4014, 4017, 4025, 4027
4015, 4027
4013
Sunstar
Techniland
TechniSat
Teco
Lennox
4023
Allsat
4015, 4023
4019
Loewe
4013
Alltech
4022, 4025
Lorenzen
Macab
4024
4013, 4019, 4025, 4030,
4031
Amstrad
4013, 4016
4027
4022
Teleciel
Telefunken
Teleka
Anglo
4025
Manhattan
Maspro
Matsui
4015, 4020, 4023
4017
Ankaro
Anttron
Apollo
Arcon
4025
4021, 4025
4017
4021
4013
4017
Mediamarkt
Medion
Metronic
Micro Technology
Minerva
Morgan’s
Mysat
4013
4020
Telemaster
Telewire
Tensai
4016
4025
4015, 4023
4016
Armstrong
Asat
4013
4013, 4017, 4020
4016
4025
4024, 4025
4022
Thomson
Thorens
Tonna
Astra
4013, 4016, 4024
4019, 4020
4015
4021
Astro
4013, 4015, 4025
4025
4015, 4023, 4025
4004
AudioTon
Bush
Toshiba
Triasat
4012, 4014
4024
Neuhaus
Neusat
4019, 4023, 4024, 4025
4025
4019
Condor
82
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 83 Tuesday, September 7, 2004 1:18 PM
Controlling Other Components—Continued
SAT (satellite receiver)
VCR
VCR
Manufacturer
Control code
Manufacturer
Control code
Manufacturer
Control code
Aiwa
2012, 2046, 2047
2003, 2004, 2022
Jensen
2013
4016
Tristar
Akai
2005, 2006, 2007, 2009,
2032, 2035, 2040, 2048
4013
Unisat
Universum
Vortec
JVC
2033, 2041, 2044, 2045,
2047
4021, 4024
4017
Alba
Kaisui
Kendo
Kenwood
Kodak
Loewe
Logik
2033
Anitech
ASA
2033
2041, 2046
2005, 2006, 2007, 2009
2010
Wela
4025
2034
Zehnder
Zenith
4020
Baird
2036
4032
Bell & Howell
Blaupunkt
2007
2028, 2034
2028, 2043
2030, 2031, 2036
2039, 2042
CBL (cable receiver)
2033, 2041, 2044, 2045,
2047
Luxor
Bush
Manufacturer
Control code
2010, 2011, 2014, 2019,
2020
Magnavox
Marantz
ABC
3001, 3002, 3021
3006
Canon
Carver
Cimline
Citizen
Colortyme
Craig
2010, 2011
2014
Archer
2005, 2006, 2007, 2009,
2010, 2014, 2031, 2034
Cabletime
Cableview
Contec
3028, 3032
3004
2033
Matsui
2028, 2041, 2046, 2047
2010
2008, 2009
2005
Matsushita
3009
2007, 2008, 2010, 2012,
2019, 2030, 2036
Eastern
GE
3010
2008
Memorex
3001, 3002
3011
Crown
2033
Metz
2039
Gemini
2001, 2005, 2008, 2009,
2010, 2011, 2023, 2026
Curtis Mathes
MGA
2022
General Instruments 3002, 3022
Minerva
Minolta
Mitsubishi
Motorola
MTC
2039
Cyrus
2034
Grundig
Hamlin
Hitachi
3031
3012
3002
2013, 2021
2013, 2022, 2032, 2034
2010
Daewoo
Dansai
Decca
2012
2033
2034
3002, 3011, 3013, 3021,
3022, 3023, 3026
Jerrold
2008
Dimensia
Dumont
Elcatech
Emerson
ESC
2001, 2026
2034, 2036, 2037
2033
Multitech
2008, 2012, 2033
Magnavox
Memorex
Movie Time
NEC
3014
2005, 2006, 2007, 2009,
2032
3015
NEC
3016
2003, 2010, 2012, 2022
2043
Neckermann
Nesco
2034
3003
2033
Nokia
3033
Ferguson
Finlandia
Finlux
2035
NOBLEX
Nokia
2008
NSC
3016
2034, 2036
2034, 2036, 2037
2033, 2041
2007, 2030, 2036
2004, 2010, 2024
2012
2030, 2036, 2043
2048
Oak
3009
Nordmende
Okano
Panasonic
Philips
3020
Firstline
Fisher
2046
3007, 3008, 3014
3017, 3024
3001, 3002
3004, 3020, 3022
3006
Olympus
Optonica
2010
Pioneer
Proscan
RCA
Fuji
2017
Funai
2028, 2041, 2045, 2046,
2047
Orion
Garrard
2012
Realistic
Sagem
Salora
2001, 2002, 2008, 2010,
2011, 2023, 2025, 2026
Osaki
2033
GE
3034
Otto Versand
Palladium
Panasonic
Pentax
2034
GEC
2034
3029
2033
GoldHand
GoldStar
Goodmans
Gradiente
Graetz
2033
Samsung
Signature
Sprucer
3017
2010, 2011, 2042
2013, 2021, 2025, 2037
2009
2005, 2009
2031, 2033
2012
3002
3020
Pentex Research
Philco
Standard
Component
2010, 2011, 2014
3018
2036, 2043
2030, 2034, 2036
2033
2010, 2014, 2017, 2034,
2048
Philips
Starcom
Stargate
Tele+1
3011, 3021
3011
Granada
Grandin
Phonola
Pioneer
Proline
2034
3030
2029, 2033, 2034, 2039,
2040, 2042, 2044
2006, 2013, 2032, 2034
Grundig
Tocom
3013
2044
Harman Kardon
HCM
2005
United Cable
Universal
Videoway
View Star
Zenith
3021, 3023
3005, 3006
3025
Proscan
Pye
2001, 2002, 2026
2034
2033, 2044
2028, 2033, 2043, 2044,
2047
Hinari
Quasar
Quelle
2010, 2011
2034
3009, 3014, 3016
3019
2013, 2021, 2025, 2028,
2037, 2038, 2043
Hitachi
Radio Shack
2017
Ingersol
Interfunk
ITT
2028
Radio Shack/
Realistic
2007, 2008, 2010, 2011,
2012, 2017
2034
Radiola
2034
2030, 2036, 2043, 2048
2005, 2006, 2007, 2008,
2010, 2011, 2013, 2014,
2021
JC Penney
83
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 84 Tuesday, September 7, 2004 1:18 PM
Controlling Other Components—Continued
VCR
TV
TV
Manufacturer
Control code
Manufacturer
Admiral
Akai
Control code
1026, 1040, 1062
1002, 1067
1045
Manufacturer
Control code
2001, 2002, 2003, 2008,
2010, 2013, 2021, 2023,
2025, 2026, 2027
1004, 1006, 1007, 1009,
1010, 1017, 1025, 1027,
1029, 1033, 1040, 1070
RCA
Emerson
Akura
2007, 2008, 2010, 2011,
2012, 2017
Envision
Erres
1004, 1006
1037
Realistic
Alba
1035, 1043
1063
Rex
2048
Amplivision
Amstrad
Amtron
Europhon
Fidelity
Finlux
1067
Roadstar
Runco
2033, 2043
2019
1035, 1067
1009
1068
1039, 1040, 1067
Saba
2040, 2048
2028, 2041
2030
Anam National
Anitech
AOC
1003, 1009
1035
1035, 1043, 1048, 1049,
1063
Firstline
Fisher
Saisho
Salora
1004, 1005, 1006
1066
1010, 1017, 1052, 1063,
1068
Samsung
Sansui
Sanyo
2008, 2043, 2049
2006, 2032
2007, 2008, 2030, 2036
2047
Arc en Ciel
Arcam
Formenti
Frontech
Fujitsu
1040
1063
1045, 1062
ASA
1040
1070
Saville
SBR
Audiovox
Autovox
Baird
1009
Funai
1009, 1045, 1048, 1070
2034
1040, 1068
1069
1001, 1003, 1004, 1006,
1011, 1012, 1019, 1034
Schaub Lorenz
Schneider
Scott
2036
GE
2033, 2034
2015
Bang & Olufsen
1040
GEC
1038, 1063, 1067, 1069
1036, 1054, 1055, 1058,
1059, 1068
Baur
Geloso
Genexxa
1035
1062
Sears
2007, 2010, 2013, 2021
2043
Beko
1052
SEG
1004, 1005, 1006, 1007,
1008, 1025, 1047, 1063
Bell & Howell
Binatone
1010, 1017
1063
GoldStar
SEI
2028, 2034
2016, 2017, 2031
2004, 2033, 2036
2028
Sharp
Goodmans
Gorenje
Graetz
1043, 1053, 1063
1052
1041, 1042, 1044, 1058,
1059
Shintom
Shorai
Blaupunkt
1062, 1069
1063, 1067
Boots
1063
1040
1040
1048
Siemens
Singer
2034, 2036, 2039
2010
Granada
Brionvega
Bruns
1039, 1041, 1042, 1058,
1059, 1064
Grundig
Sinudyne
Sonolor
Sony
2028, 2034
2030, 2031
2004, 2018, 2024
2010, 2021
2046
BSR
Hallmark
Hanseatic
Hantarex
HCM
1004, 1006
1060, 1068
1067
1035, 1043, 1048, 1050,
1053, 1057
Bush
STS
Cascade
Celebrity
Century
Cimline
1035
1035
Sunkai
Sylvania
Symphonic
Tandy
1002
Hinari
1035, 1043
2010, 2011, 2012, 2014
2012
1040
1004, 1006, 1007, 1013,
1027, 1038, 1062, 1063,
1069
1035, 1043
Hitachi
2007
1004, 1006, 1009, 1017,
1022, 1025
Citizen
Tatung
Teac
2034
Huanyu
ICE
1053
Clatronic
Colortyme
Condor
1052
2012
1045, 1063
1052
1004, 1006
Technics
Teknika
Telefunken
Thomson
Thorn
2010, 2042
2010, 2012
2048
Imperial
Infinity
Inno Hit
Interfunk
Intervision
ITT
1052
1014
Contec
1035
1056, 1067
1055, 1062, 1066, 1069
1045, 1063
1062, 1068, 1069
1014
Contec/Cony
Continental Edison
Craig
1007, 1009
2048
1066
2035, 2036
1009
2013, 2015, 2022, 2034,
2048
Toshiba
Crosley
1040
JBL
Totevision
2008
Crown
1009, 1014, 1035, 1052
1001, 1004, 1005, 1006,
1011, 1012, 1016, 1019,
1022, 1025, 1034
Uher
2043
1001, 1004, 1006, 1010,
1017, 1022, 1025, 1034
JC Penney
Curtis Mathes
Daewoo
Unitech
2008
1004, 1005, 1006, 1025,
1035, 1053
Jensen
JVC
1004, 1006
Universum
Vector Research
Video Concepts
2034, 2039, 2043
2005, 2006
2005, 2006, 2022
1007, 1012, 1013, 1015,
1033
Daytron
Decca
1004, 1006, 1025, 1035
1067
Kaisui
1035, 1063
1062, 1069
1060
2008, 2010, 2012, 2013,
2017, 2021, 2027
Wards
Dimensia
Dixi
1001, 1034
1035
Kapsch
Kathrein
Kawasho
Kendo
XR-1000
Yamaha
Yoko
2010, 2012
Dual
1057, 1068
1004, 1039, 1040
1002
1002, 1004, 1006
1043
2005, 2006, 2007, 2009
2043
Dumont
Electroband
Kenwood
Kloss Novabeam
Korting
KTV
1004, 1006, 1008
1009
Zenith
2004, 2019, 2024
1002, 1003, 1004, 1006,
1008
Electrohome
Elta
1040
1035
1009, 1025
1005
LG
84
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 85 Tuesday, September 7, 2004 1:18 PM
Controlling Other Components—Continued
TV
TV
TV
Manufacturer
Control code
1014, 1040, 1055
1004, 1006
Manufacturer
Control code
Manufacturer
Technics
Techwood
Control code
Loewe
Quasar
1003, 1012, 1031
1012, 1044, 1061
1004, 1006, 1012
Luxman
1036, 1039, 1054, 1055,
1058, 1059, 1068
Quelle
1001, 1006, 1010, 1014,
1016, 1017, 1034
1004, 1005, 1006, 1007,
1009, 1022, 1025, 1031,
1070
LXI
Radio Shack
1010, 1017, 1034
Teknika
M Electronic
Magnadyne
Magnafon
1035, 1053, 1062, 1063
1040, 1067, 1068
1067
1001, 1004, 1006, 1007,
1009, 1010, 1017, 1021,
1025
Radio Shack/
Realistic
Teleavia
Telecaption
Telefunken
Teletech
Teleton
1066
1024
Radiola
1037
1066
1004, 1006, 1008, 1014,
1018, 1020
Magnavox
Marantz
Matsui
Radiomarelli
1040, 1067
1035
1001, 1003, 1004, 1005,
1006, 1008, 1027, 1034
1004, 1006, 1014, 1060
RCA
1063
1035, 1043, 1048, 1050,
1063, 1064, 1067, 1068
Tensai
1048
Realistic
Rex
1010, 1017, 1034
1045, 1062
Thomson
Thorn
1066
Megatron
Memorex
1006
1054, 1055, 1058
RFT
1040
1005, 1006, 1010, 1017,
1035
1010, 1016, 1017, 1022,
1024, 1039
Roadstar
Saba
1035, 1045
Toshiba
Metz
1040, 1051, 1058
1040, 1062, 1066, 1069
Totevision
Triumph
1025
MGA
1004, 1005, 1006, 1008
1039, 1058, 1059, 1064
1035, 1043, 1045, 1067,
1068
Saisho
1067
Minerva
Universal
Universum
Voxson
1011, 1019
1045, 1052, 1058
1040, 1062
1063
Salora
1062
1004, 1005, 1006, 1008,
1040, 1055, 1058
Mitsubishi
Sambers
Sampo
1056, 1067
1004, 1006, 1025
Mivar
1047, 1056, 1067
1003, 1026
Waltham
Motorola
1004, 1005, 1006, 1007,
1008, 1022, 1025, 1035,
1045, 1047, 1052, 1056,
1060, 1063, 1065
1001, 1004, 1005, 1006,
1008, 1011, 1014, 1018,
1019, 1020, 1021, 1034,
1070
1004, 1005, 1006, 1022,
1055
Samsung
MTC
Wards
Multitech
NAD
1009, 1035
Sansui
1029
1006, 1016
Watt Radio
Wega
1068
Sanyo
1004, 1010, 1017
1037, 1038
1069
NEC
1003, 1004, 1005, 1006
1040
SBR
1040, 1041, 1054, 1059,
1060
Yamaha
Yoko
1004, 1005, 1006, 1008
1045, 1063
Neckermann
Schaub Lorenz
Schneider
1068
Nikkai
1045
Zenith
1004
1004, 1006, 1007, 1009,
1070
Nikko
1006
Scott
Oceanic
Onwa
1062
1001, 1004, 1006, 1008,
1010, 1015, 1016, 1017,
1028, 1034, 1070
1009
Sears
Optonica
1021, 1026
SEG
1045, 1063
1029, 1043, 1048, 1049,
1050, 1067, 1068
Orion
Osaki
1036, 1040, 1048, 1067,
1068
SEI
1045, 1063
Seleco
Sharp
1062
1036, 1041, 1043, 1054,
1055, 1058, 1059, 1060,
1063
Otto Versand
Palladium
Panasonic
Pathe Marconi
Philco
1004, 1006, 1007, 1021,
1023, 1025, 1026
1052
Shorai
1048
1003, 1012, 1014, 1031,
1044, 1046, 1051, 1061,
1062, 1069
Siarem
Siemens
Singer
1040, 1067
1041, 1042, 1058, 1059
1040
1066
1036, 1040, 1043, 1067,
1068
1003, 1004, 1005, 1006,
1007, 1008, 1014, 1018,
1040
Sinudyne
Solavox
Sonoko
Sonolor
1062
1035
1062
1003, 1004, 1007, 1008,
1014, 1018, 1019, 1020,
1037, 1038, 1040, 1053,
1059, 1060
Philips
1002, 1030, 1032, 1036,
1054
Sony
Phoenix
Phonola
Pioneer
Portland
Price Club
Prism
1040
Soundesign
Starlite
1004, 1006, 1009, 1070
1037, 1040
1004, 1006, 1027, 1062
1004, 1005, 1006, 1025
1022
1009
Stern
1062
Sunkai
1043, 1048, 1049, 1050
1004, 1006, 1008, 1014,
1018, 1020
1012
Sylvania
Profex
1035
Symphonic
Tandy
1009, 1028
Proline
Proscan
Protech
Proton
1049
1026, 1062, 1063
1038, 1063
1001, 1034
1035, 1045, 1063
1004, 1006, 1007
1037
Tashiko
Tatung
Tec
1003, 1063, 1067
1063
Pye
85
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 86 Tuesday, September 7, 2004 1:18 PM
Controlling Other Components—Continued
To control another component, point the remote control-
ler at it and use the buttons as explained below (you must
select the appropriate remote control mode first).
Controlling a Cable Receiver
STANDBY
ON
Controlling a TV
Number
buttons
*
STANDBY
ON
TV
*
*
TV INPUT
TV CH +/–
Press
[CABLE]
first
Number
buttons
*
TV VOL
Press [TV]
first
CH
CH
VOL
Set the cable receiver to On or
Standby
[ON], [STANDBY]
[CH +/–]
Select cable channels
Number buttons Enter numbers
[ON], [STANDBY] Set the TV to On or Standby
Turn the TV on or off
Number buttons Enter numbers
The following buttons control the AV Receiver.
[VOL]: Adjusts the volume of the AV receiver.
[MUTING]: Mutes the AV Receiver.
TV [
]
[CH +/–]
Select channels on the TV
[TV INPUT]
Select inputs on the TV
Adjust the TV’s volume
VOL [ ]/[
]
Buttons marked with an asterisk can always be used to
control a TV regardless of the currently selected remote
controller mode.
*
The following buttons control the AV Receiver.
[VOL]: Adjusts the volume of the AV receiver.
[MUTING]: Mutes the AV Receiver.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 87 Tuesday, September 7, 2004 1:18 PM
Controlling Other Components—Continued
Controlling a VCR
Controlling a Satellite Receiver
STANDBY
ON
STANDBY
ON
Number
buttons
Press [SAT]
first
Press
[VCR] first
ENTER
CH
CH
,
REC
Set the satellite receiver to On or
Standby
[ON], [STANDBY] Set the VCR to On or Standby
[ON], [STANDBY]
[CH +/–]
[CH +/–]
Selects channels on the VCR
Play
Select satellite channels
Select menu items
[
[
[
[
[
]
[
]/[ ]/[ ]/[
]
Stop
]
[ENTER]
Confirm selection
Rewind
Fast forward
Pause
]
]
Number buttons Enter numbers
The following buttons control the AV Receiver.
[VOL]: Adjusts the volume of the AV receiver.
[MUTING]: Mutes the AV Receiver.
]
REC [
]
Record
The following buttons control the AV Receiver.
[VOL]: Adjusts the volume of the AV receiver.
[MUTING]: Mutes the AV Receiver.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 88 Tuesday, September 7, 2004 1:18 PM
Controlling Other Components—Continued
Learning Commands from Another
Remote Controller
Point the remote controllers at
each other, about 2 to 6 inches
(5–15 cm) apart, and then, on the
other remote controller,press the
button whose command you
want to learn.
3
The AV receiver’s remote controller can learn the com-
mands of other remote controllers simply by pointing
them at each other. For example, by transmitting the Play
command from your CD player’s remote controller, the
remote controller can learn it and then transmit the same
command when its Play [ ] button is pressed in CD
mode.
E
M
L U
V O
N G
I
T
U
M
L
E
N
S T
E
T O
L
T
S E
H
C
E T
S
E
R
E
P
C
D
D
P
E R
D V
T A
H
N
I - C P U
L T I N
O
T U
N
O
R
P
U
H
M U
P
O
E
R
T O
C
G
D
R
R
O
E
N
U
U
M
L E
S
- 2
E
O
D
D I S C
T
E
C
R
T
S
E
I D
About 2 to 6
inches (5–15 cm
U
P
M
V
E
P
I M
I N
1
D
T A
O -
E
P
E
V I D
L E
D
V
S
D
This is convenient when you want to add commands to
buttons after entering a remote control code (page 80).
R
E
W
O
P
ON
ST
V
1
A
ND
1
BY
V
4
4
5
V
2
C
D
M
2
U
I
L
7
TI
C
T
V
V
H
+
T
3
1
APE
--
/---
0
3
IN
D
P
8
VD
U
T
INPUT
6
TU
1
0
+
N
ER
T
V
SELEC
CRO
M
A
9
CH
C
L
E
2
TOR
A
RE
R
M
O
TE
T
V
D
VD
VO
3
L
M
O
DE
C
D
C
A
BL
M
E
D
/C
D
R
RC-588M
SA
T
S
LE
EP
1, 4
To teach the AV receiver’s remote
controller more new commands,
repeat steps 2 and 3.
4
Press the [ON] button when you’ve fin-
ished.
Notes:
• The following buttons cannot be taught new com-
mands: REMOTE MODE, MACRO [1], [2], [3], TV
1
[
[
], TV [INPUT], TV CH [+]/[–], TV VOL [ ]/
].
• The AV receiver’s remote controller can learn up to
approximately 150 commands. However, the com-
mands of some remote controllers may use a lot of
memory, in which case, this will be reduced.
• By default, the AV receiver’s remote controller knows
the commands for controlling an Onkyo CD player,
cassette deck, DVD player, and MD player (e.g., Play,
Stop, Pause, etc., buttons). These buttons can learn
new commands, although the defaults will be restored
if the remote controller is reset.
While holding down the REMOTE
MODE button that you want to
learn the command, press the
[ON] button.
1
2
• To learn a new command for a button that has already
learned one, simply repeat this procedure.
• Like most remote controllers, the AV receiver’s
remote controller uses infrared. Commands from
remote controllers that don’t use infrared cannot be
learnt.
ON
• When the remote controller’s batteries expire, all
learned commands will be lost and will have to be
learned all over again, so don’t discard your other
remote controllers.
On the AV receiver’s remote con-
troller, press the button you want
to learn the new command.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 89 Tuesday, September 7, 2004 1:18 PM
Controlling Other Components—Continued
Using Macros
On the remote controller, press
the buttons whose actions you
want to program into the macro
in the order you want them per-
formed.
For example, to program the previous
CD example into a macro, press the fol-
lowing buttons: REMOTE MODE
[RECEIVER], [ON], INPUT SELEC-
TOR [CD], REMOTE MODE [CD],
Play [ ].
2
With the Macro function, you can program the remote
controller’s MACRO buttons to perform a sequence of
actions with just one button press. For example, nor-
mally you need to perform the following actions to play
a CD:
[RECEIVER] button
1. Press the REMOTE MODE
to select Receiver mode.
2. Press the [ON] button to turn on the AV receiver.
3. Press the [CD] INPUT SELECTOR button to
select the CD input source.
4. Press the REMOTE MODE [CD] button to select
the CD remote controller mode.
5. Press the Play [ ] button to start playback on the
CD player.
When you’ve finished, press the
MACRO button again.
3
Notes:
With the Macro function, you can program one of the
MACRO buttons to perform all five actions in one go.
• If after programming a macro you teach one of the
buttons in that macro a new command, then the macro
will no longer work properly. In this case, you must
program the macro again.
Making Macros
There are three MACRO buttons, and each button can be
programmed with a different macro in each remote con-
troller mode. Each macro can perform up to eight
actions.
Running Macros
Programmed macros can be run as follows.
Press the MACRO [1], [2], or [3]
button.
1
The actions in the macro are performed
in the order in which they were pro-
grammed.
1
1
While holding down the REMOTE
1
MODE button for the mode that
you want to learn the macro,
press MACRO button [1], [2], or
[3].
The Remote indicator lights up.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 90 Tuesday, September 7, 2004 1:18 PM
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can’t resolve the issue
yourself, contact your Onkyo dealer.
• For the TX-SR702/702E, if your turntable uses an MC
cartridge, you must connect an MC head amp or an
MC transformer (see page 36).
• Make sure that none of the connecting cables are bent,
twisted, or damaged.
Power
• Not all listening modes use all speakers (page 62).
• Specify the speaker distances (page 48) and adjust the
individual speaker levels (page 50).
• Make sure that the speaker setup microphone is not
still connected.
Can’t turn on the AV receiver?
• Make sure that the power cord is properly plugged into
the wall outlet.
• Unplug the power cord from the wall outlet, wait five
seconds or more, then plug it in again.
Only the front speakers produce sound?
• When the Stereo listening mode is selected, only the
front speakers and subwoofer produce sound.
• When the Direct or Pure Audio (not all models) listen-
ing mode is selected, only the front speakers produce
sound.
The AV receiver turns off as soon as it’s turned
on?
• The amp protection circuit has been activated.
Remove the power cord from the wall outlet immedi-
ately and contact your Onkyo dealer.
• Make sure the speakers are configured correctly
(page 46).
Audio
Only the center speaker produces sound?
• If you use the Pro Logic IIx Movie or Pro Logic IIx
Music listening mode with a mono source, such as an
AM radio station or mono TV program, the sound is
concentrated in the center speaker.
There’s no sound, or it’s very quiet?
• Make sure that all audio connecting plugs are pushed
in all the way (page 21).
• Make sure that the inputs and outputs of all compo-
nents are connected properly (page 21).
• Make sure the speakers are configured correctly
(page 46).
• Make sure that the polarity of the speaker cables is
correct, and that the bare wires are in contact with
metal part of each speaker terminal (page 23)
• Make sure that the input source is properly selected
(page 53).
• Make sure that the speaker cables are not shorting.
• Check the volume. It can be set to MIN, 1 through 99,
or MAX (page 53). The AV receiver is designed for
home theater enjoyment. It has a wide volume range,
allowing precise adjustment.
• If the MUTING indicator is shown on the display,
press the remote controller’s [MUTING] button to
unmute the AV receiver (page 54).
• While a pair of headphones is connected to the
PHONES jack, no sound is output by the speakers
(page 54).
• Check the digital audio output setting on the con-
nected device. On some games consoles, such as those
that support DVD, the default setting is off.
• With some DVD-Video discs, you need to select an
audio output format from a menu.
• For the TX-SR602/602E and TX-SR8260, if your
turntable doesn’t have a built-in phono preamp, you
must connect one between it and the AV receiver. If
your turntable uses an MC cartridge, you must con-
nect an MC head amp, or an MC transformer and
phono equalizer.
The surround speakers produce no sound?
• When the Stereo, Direct, or Pure Audio (not all mod-
els) listening mode is selected, the surround speakers
produce no sound (page 62).
• Depending on the source and current listening mode,
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
• Make sure the speakers are configured correctly
(page 46).
The center speaker produces no sound?
• When the Mono, Stereo, Direct, Pure Audio (not all
models), or Orchestra listening mode is selected, the
center speaker produces no sound (page 63).
• Make sure the speakers are configured correctly
(page 46).
The surround back speakers produce no
sound?
• The surround back speakers are not used with all lis-
tening modes. Select another listening mode
(page 62).
• Not much sound may be produced by the surround
back speakers with some sources.
• Make sure the speakers are configured correctly
(page 46).
90
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 91 Tuesday, September 7, 2004 1:18 PM
Troubleshooting—Continued
The subwoofer produces no sound?
• When you play source material that contains no infor-
mation in the LFE channel, the subwoofer produces
no sound.
• Make sure the speakers are configured correctly
(page 46).
About DTS signals
• When DTS program material ends and the DTS bit-
stream stops, the AV receiver remains in DTS listen-
ing mode and the DTS indicator remains on. This is to
prevent noise when you use the pause, fast forward, or
fast reverse function on your player. If you switch your
player from DTS to PCM, because the AV receiver
does not switch formats immediately, you may not
hear any sound, in which case you should stop your
player for about three seconds, and then resume play-
back.
• With some CD and LD players, you won’t be able to
playback DTS material properly even though your
player is connected to a digital input on the AV
receiver. This is usually because the DTS bitstream
has been processed (e.g., output level, sampling rate,
or frequency response changed) and the AV receiver
doesn’t recognize it as a genuine DTS signal. In such
cases, you may hear noise.
There’s no sound with a certain signal format?
• Check the digital audio output setting on the con-
nected device. On some games consoles, such as those
that support DVD, the default setting is off.
• With some DVD-Video discs, you need to select an
audio output format from a menu.
• Depending on the input signal, some listening modes
cannot be selected (page 61).
Can’t select the DTS-ES Discrete/Matrix orTHX
Surround EX (TX-SR702/702E only) listening
modes?
• These modes cannot be selected when no surround
back speakers are connected, or the Zone 2 speakers
are being used.
• When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a mal-
function.
Can’t get 6.1 playback?
• If no surround back speakers are connected, or the
Zone 2 speakers are being used, 6.1 playback is not
possible.
Video
The volume cannot be set to 99?
• When the levels of all speakers have been calibrated
(page 50), the maximum volume setting may change.
There’s no picture?
• Make sure that all video connecting plugs are pushed
in all the way (page 21).
Noise can be heard?
• Make sure that each video component is properly con-
nected.
• If your video component is connected to a component
video input, your TV must be connected to the compo-
nent video output (page 26).
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance, so don’t do it.
• An audio cable may be picking up interference. Try
repositioning your cables.
•
Models other than the TX-SR702/702E, TX-SR602E,
and Australian TX-SR602 do not support video upcon-
version, so composite video and S-Video sources are
not output by the COMPONENT VIDEO OUT.
The Late Night function doesn’t work?
• Make sure the source material is Dolby Digital
(page 64).
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
• While the Pure Audio listening mode (not all models)
is selected, the video circuits are turned off and the AV
receiver outputs no video signals.
The DVD analog multichannel input doesn’t
work?
• Check the DVD analog multichannel input connec-
tions (page 29).
• To select the DVD analog multichannel input, press
the [MULTI CH] input selector button.
• Check the audio output settings on your DVD player.
The onscreen menus don’t appear?
• Make sure that the video settings are correct
(page 43).
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
• Depending on the display device, when the “b. Scan
Mode” setting on the “6-3. OSD Setup” menu is set to
Non-Interlaced, the onscreen setup menus may not
appear. If this happens, use the AV receiver’s display
and change that setting to Interlaced.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 92 Tuesday, September 7, 2004 1:18 PM
Troubleshooting—Continued
• Are you trying to learn from a remote controller that
cannot be used for learning? Some commands cannot
be learnt, especially those that transmit several
instructions with a single button press.
• The wrong remote control code has been entered.
• The entered remote control code may not be correct. If
more than one code is listed, try each one.
• With some AV components, certain buttons may not
work as expected, and some may not work at all.
• To control Onkyo components, point the remote con-
troller at the AV receiver.
Tuner
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t
appear?
• Relocate your antenna.
• Move the AV receiver away from your TV or com-
puter.
• Listen to the station in mono (page 56).
• When listening to anAM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
• To control another manufacturer’s component, point
the remote controller at that component.
Recording
Can’t record?
• On your recorder, make sure the correct input is
selected (e.g., digital or analog).
Remote Controller
The remote controller doesn’t work?
• Make sure that the batteries are installed with the cor-
rect polarity (page 13).
Zone 2
• Install new batteries. Don’t mix different types of bat-
teries, or old and new batteries (page 13).
• Make sure that the remote controller is not too far
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor (page 13).
• Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
• If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not
work reliably when the doors are closed.
• Make sure you’ve selected the correct remote control-
ler mode (page 13).
Zone 2 has turned off?
• Was the Sleep function set? The Sleep function turns
off Zone 2 as well as the AV receiver. To set the Sleep
function for Zone 2 only, see page 78.
There’s no sound?
• Since the Zone 2 function and the REC OUT outputs
use the same circuitry, you cannot use Zone 2 and
record at the same time. When the [REC OUT] button
is pressed, Zone 2 is turned off.
• Only components connected to analog inputs can be
played in Zone 2.
• When using the remote controller to control other
manufacturers’AV components, some buttons may
not work as expected.
• Make sure you’ve entered the correct remote control
code.
Can’t control other components?
• If it’s an Onkyo component, make sure that the
cable and analog audio cable are connected properly.
Connecting only an
cable won’t work (page 37).
• Make sure you’ve selected the correct remote control-
ler mode (page 14).
• If you connect an MD recorder or CD recorder to the
TAPE jacks, be sure to set make the necessary setting
(pages 52 and 80).
• When learning commands, make sure that the trans-
mitting ends of both remote controllers are pointing at
each other.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 93 Tuesday, September 7, 2004 1:18 PM
Troubleshooting—Continued
The AV receiver uses a battery-less memory backup
system in order to retain radio presets and other set-
tings when it’s unplugged or in the case of a power fail-
ure. Although no batteries are required, the AV receiver
must be plugged into an AC outlet in order to charge the
backup system.
(On non-American and Australian models, the AV
receiver’s POWER switch must be set to ON in order to
charge the backup system.) Once it has been charged,
the AV receiver will retain the settings for several
weeks, although this depends on the environment and
will be shorter in humid climates.
Others
The sound changes when I connect my head-
phones?
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Direct, or Pure Audio (not all models). When you dis-
connect the headphones, the previous listening mode
will be resumed.
The speaker volume cannot be set as required?
• When the Automatic Speaker Setup function is used,
or the volume is adjusted on the onscreen setup
menus, the maximum possible volume setting may
change.
The speaker distance cannot be set as
required?
• In some cases, corrected values suitable for home the-
ater use may be set automatically.
The display doesn’t work?
• The display is turned off when the Pure Audio (not all
models) listening mode is selected.
• Actions are not displayed on the TV or projector that’s
connected to the COMPONENT VIDEO OUT.
How do I change the language of a multiplex
source?
• Use the “a. Input Channel” setting on the “3-5. Multi-
plex” menu to select Main or Sub (page 69).
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
Resetting the AV receiver to its factory defaults
To reset the AV receiver to its factory defaults, turn it on
and, while holding down the [VIDEO 1] button, press
the [STANDBY/ON] button.“CLEAR” will appear on the
display and the AV receiver will enter Standby mode.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 94 Tuesday, September 7, 2004 1:18 PM
Specifications (TX-SR702/702E)
Amplifier Section
General
Power Output
2 channel driven:
Power Supply
American: AC 120 V, 60 Hz
Australian and European: AC 230-240 V,
50 Hz
Others : AC 120/220-230 V, 50/60 Hz
AC 230-240 V, 50Hz
AC 220-230 V, 50/60 Hz
American : 8.1A
Others : 700 W
American 100 W + 100 W (8Ω,20Hz–
:
20kHz,FTC)
Europian: 130 W + 130 W
(6Ω,1kHz,DIN)
Asian: 160 W + 160 W (6Ω,1kHz,JEITA)
230 W + 230 W (3Ω,Front)
170 W + 170 W (4Ω,Front)
115 W + 115 W (8Ω,Front)
Dynamic Power
Power Comsumption
Stand-by Power
Comsumption
THD (Total Harmonic
Distortion)
1.0 W
0.08 % (Power Rated)
Dimensions(W x H x D) 435 W x 175 H x 430 D mm
17-1/8" W x 6-7/8" H x 16-15/16" D inches
Damping Factor
Input Sensitivity and
Impedance
60 (Front,1kHz,8Ω)
200 mV/ 47 kΩ (LINE)
2.5 mV/ 4.7 kΩ (PHONO MM)
Weight
American, Australian,
European, Singapore
and East southern asian: 15.2 kg
33.5 lbs
Output Level and
Impeadance
Phono Overload
Frequency Response
200 mV/ 470 Ω (REC OUT)
70 mV (MM 1kHz 0.5 %)
10 Hz–100 kHz/ +1 dB-3 dB (Direct
mode)
Others: 16.0 kg
35.3 lbs
■ Video Inputs
Component Video Input 1,2,3
S-VideoCompatibleJack
Tone Control
SN Ratio
10 dB, 50 Hz (BASS)
10 dB, 10 kHz (TREBLE)
106 dB (LINEIHF-A)
80 dB (PHONO,IHF-A)
American : 6Ω~
Input
DVD,VIDEO1,VIDEO2,VIDEO3,
VIDEO4
Speaker Impedance
A/V Input
DVD,VIDEO1,VIDEO2,VIDEO3,
VIDEO4
other :4 Ω~
Video Section
■ Video Outputs
Component Video
Output
S-VideoCompatibleJack
Output
Input Sensitivity/Output
Level and Impedance
OUT
1 Vp-p /75Ω (Component and S-VideoY)
0.7 Vp-p /75Ω (Component Pb/Cb,Pr/Cr)
0.28 Vp-p /75Ω(S-Video C)
MONITOR OUT,VIDEO1,VIDEO2
MONITOR OUT,VIDEO1,VIDEO2
A/V Output
1 Vp-p /75Ω(Composite)
Component Video
Frequency Response
■ Audio Inputs
Digital Inputs
5 Hz – 50 MHz
Optical : 5
Coaxial : 2
DVD(MULTICHANNEL),VIDEO1,VID
Tuner Section
Analog Inputs
EO2,VIDEO3,VIDEO4,TAPE,CD,PHO
NO
6
■ FM
Multichannel Inputs
Tuning Frequency RangeAmerican: 87.5 MHz– 107.9 MHz
Other : 87.5 MHz– 108.0 MHz
■ Audio Outputs
Digital Outputs
Usable Sensitivity
Stereo; 17.2 dBf 2 µV(75Ω IHF)
Mono; 11.2 dBf 1 µV(75Ω IHF)
Stereo; 70 dB (IHF-A)
Mono; 76 dB (IHF-A)
Stereo; 0.3 % (1kHz)
Mono 0.2 % (1kHz)
30 Hz–15 kHz / 1 dB
45 dB ( 1kHz )
Optical : 1
Coaxial : 1
TAPE,VIDEO1,VIDEO2
S/N Ratio
Analog Outputs
Multichannel Pre
Outputs
Subwoofer Pre Outputs
Speaker Outputs
Phones
THD
7
1
9
1
Frequency Response
Stereo Separation
■ AM
■ Other Jacks
RS-232 Control
IR Input
Tuning Frequency RangeAmerican: 530 kHz–1700 kHz
Others: 522 kHz–1611 kHz
1 (Not American, Austratian)
1
1
Usable Sensitivity
S/N Ratio
THD
30 µV
40 dB
0.70%
12V Trigger Out
Specifications and features are subject to change without
notice.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 95 Tuesday, September 7, 2004 1:18 PM
Specifications (TX-SR602/602E, TX-SR8260)
Amplifier Section
General
Power Output
2 channel driven:
Power Supply
American: AC 120 V, 60 Hz
Australian and European: AC 230-240 V,
50 Hz
Others: AC 120/220-230 V, 50/60 Hz
AC 230-240 V, 50Hz
AC 220-230 V, 50/60 Hz
American : 6.7A
Others: 650 W
American : 85 W + 85 W
(8Ω,20Hz–20kHz, FTC)
Europian : 120 W + 120 W
(6Ω,1kHz,DIN)
Asian, Australian : 150 W + 150 W
(6Ω,1kHz,JEITA)
220 W + 220 W (3Ω,Front)
165 W + 165 W (4Ω,Front)
100 W + 100 W (8Ω,Front)
Power Comsumption
Dynamic Power
Stand-by Power
Comsumption
1.0 W
THD (Total Harmonic 0.08 % (Power Rated)
Distortion)
Damping Factor
Input Sensitivity and
Impedance
Output Level and
Impeadance
Frequency Response
Dimensions(W x H x D) 435 W x 175 H x 430 D mm
17-1/8" W x 6-7/8" H x 16-15/16" D inches
Weight
60 (Front,1kHz,8Ω)
200 mV/ 47 kΩ (LINE)
American, Australian,
European, Singapore
and East southern asian: 13.6 kg
30.0 lbs
Others: 14.8 kg
32.6 lbs
200 mV/ 470 Ω (REC OUT)
10 Hz–100 kHz/ +1 dB-3 dB (Direct
mode)
Tone Control
10 dB, 50 Hz (BASS)
10 dB, 10 kHz (TREBLE)
106 dB (LINEIHF-A)
American : 6Ω–
■ Video Inputs
Component Video Input 1,2,3
S-VideoCompatibleJack
SN Ratio
Speaker Impedance
Input
DVD,VIDEO1,VIDEO2,VIDEO3,
VIDEO4
DVD,VIDEO1,VIDEO2,VIDEO3,
Others :4 Ω–
A/V Input
VIDEO4
Video Section
■ Video Outputs
Component Video
Output
S-VideoCompatibleJack
Output
Input Sensitivity/Output
Level and Impedance
1 Vp-p /75Ω (Component and S-VideoY)
0.7 Vp-p /75Ω (Component Pb/Cb,Pr/Cr)
0.28 Vp-p /75Ω(S-Video C)
OUT
MONITOR OUT,VIDEO1,VIDEO2
MONITOR OUT,VIDEO1,VIDEO2
1 Vp-p /75Ω(Composite)
A/V Output
Component Video
Frequency Response
5 Hz – 50 MHz
■ Audio Inputs
Digital Inputs
Optical :4(American)/ 3(other)
Coaxial : 2
Tuner Section
Analog Inputs
■ FM
DVD(MULTICHANNEL),VIDEO1,
VIDEO2,VIDEO3,VIDEO4,TAPE,CD
6
Tuning Frequency RangeAmierican; 87.5 MHz– 107.9 MHz
Others; 87.5 MHz– 108.0 MHz
Multichannel Inputs
Usable Sensitivity
Stereo:17.2 dBf 2 µV(75Ω IHF)
Mono: 11.2 dBf 1 µV(75Ω IHF)
Stereo: 70 dB (IHF-A)
Mono:76 dB (IHF-A)
Stereo: 0.3 % (1kHz)
■ Audio Outputs
Digital Outputs
S/N Ratio
1 (Optical ) 0 (Coaxial )
Analog Outputs
Subwoofer Pre Outputs
Speaker Outputs
Phones
TAPE,VIDEO1,VIDEO2
THD
1
9
1
Mono:0.2 % (1kHz)
30 Hz–15 kHz / 1 dB
45 dB ( 1kHz )
Frequency Response
Stereo Separation
■ Other Jacks
IR Input
12V Trigger Out
■ AM
1
1
Tuning Frequency RangeAmerican; 530 kHz–1700 kHz
Others; 522 kHz–1611 kHz
Usable Sensitivity
S/N Ratio
THD
30 µV
40 dB
0.70%
Specifications and features are subject to change without
notice.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
TX-NR702,602_En.book Page 96 Tuesday, September 7, 2004 1:18 PM
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
HOMEPAGE
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
I0409-4
SN 29343831C
(C) Copyright 2004 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 3 8 3 1 C *
Download from Www.Somanuals.com. All Manuals Search And Download.
|