Onkyo Car Stereo System CR 505DA User Manual

Contents

Introduction

CD Receiver

Connections

Getting Started

CD/MP3 Playback

DAB

CR-505DAB

Instruction Manual

FM/AM

Thank you for purchasing an Onkyo CD Receiver.

Please read this manual thoroughly before making

connections and turning on the power.

Using Other Functions 31

Following the instructions in this manual will enable

you to obtain optimum performance and listening

enjoyment from your new CD Receiver.

Please retain this manual for future reference.

Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions

1. Recording Copyright

7. Moisture Condensation

Unless it’s for personal use only, recording copyrighted

material is illegal without the permission of the copy-

right holder.

Moisture condensation may damage this unit.

Read the following carefully:

When you take a glass containing a cold drink outside

on a summer’s day, drops of water, called condensation,

form on the outside of the glass. Similarly, moisture

may condense on the lens of the optical pickup, one of

the most important parts inside this unit.

2. AC Fuse

TheAC fuse inside the CR-505DAB is not user-service-

able. If you cannot turn on the CR-505DAB, contact

your Onkyo dealer.

• Moisture condensation can occur in the following sit-

uations:

— The unit is moved from a cold place to a warm

place.

— A heater is turned on, or cold air from an air con-

ditioner is hitting the unit.

— In the summer, when this unit is moved from an

air conditioned room to a hot and humid place.

— The unit is used in a humid place.

• Do not use this unit when there’s the possibility of

moisture condensation occurring. Doing so may

damage your discs and certain parts inside this unit.

If condensation does occur, remove all discs and leave

this unit turned on for two to three hours. By this time,

the unit will have warmed up and any condensation will

have evaporated. To reduce the risk of condensation,

keep this unit connected to a wall outlet.

3. Care

Occasionally you should dust the CR-505DAB all over

with a soft cloth. For stubborn stains, use a soft cloth

dampened with a weak solution of mild detergent and

water. Dry the CR-505DAB immediately afterwards

with a clean cloth. Don’t use abrasive cloths, thinners,

alcohol, or other chemical solvents, because they may

damage the ﬁnish or remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SECTION

CAREFULLY.

AC outlet voltages vary from country to country. Make

sure that the voltage in your area meets the voltage

requirements printed on the CR-505DAB’s rear panel

(AC 230 -240 V, 50 Hz).

Setting the [STANDBY/ON] switch to STANDBY does

not fully shutdown the CR-505DAB. If you do not

intend to use the CR-505DAB for an extended period,

remove the power cord from the AC outlet.

For British models

Replacement and mounting of an AC plug on the power

supply cord of this unit should be performed only by quali-

ﬁed service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with

the following code:

5. Never Touch This Unit with Wet Hands

Never handle this unit or its power cord while your

hands are wet or damp. If water or any other liquid gets

inside this unit, have it checked by your Onkyo dealer.

Blue: Neutral

Brown: Live

6. Installing This Unit

As the colours of the wires in the mains lead of this appara-

tus may not correspond with the coloured markings identi-

fying the terminals in your plug, proceed as follows:

The wire that is coloured blue must be connected to the ter-

minal that is marked with the letter N or coloured black.

The wire that is coloured brown must be connected to the

terminal that is marked with the letter L or coloured red.

• Install this unit in a well-ventilated location.

• Ensure that there’s adequate ventilation all around

this unit, especially if it’s installed in an audio rack. If

the ventilation is inadequate, the unit may overheat,

leading to malfunction.

• Do not expose this unit to direct sunlight or heat

sources, because its internal temperature may rise,

shortening the life of the optical pickup.

• Avoid damp and dusty places, and places subject to

vibrations from loudspeakers. Never put the unit on

top of, or directly above, a loudspeaker.

• Install this unit horizontally. Never use it on its side

or on a sloping surface, because it may cause a mal-

function.

IMPORTANT

A 3, 5 or 13 ampere fuse is ﬁtted in this plug. Should the

fuse need to be replaced, please ensure that the replacement

fuse has a rating of 3, 5 or 13 amperes and that it is approved

by ASTA or BSI to BS1362. Check for the ASTA mark or

the BSI mark on the body of the fuse.

IF THE FITTED MOULDED PLUG IS UNSUITABLE

FOR THE SOCKET OUTLET IN YOUR HOME THEN

THE FUSE SHOULD BE REMOVED AND THE PLUG

CUT OFF AND DISPOSED OF SAFELY. THERE IS A

DANGER OF SEVERE ELECTRICAL SHOCK IF THE

CUT OFF PLUG IS INSERTED INTO ANY 13 AMPERE

SOCKET.

• If you install this unit near a TV, radio, or VCR, the

sound quality may be affected. If this occurs, move

this unit away from the TV, radio, or VCR.

If in any doubt, consult a qualiﬁed electrician.

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions—Continued

Declaration of Conformity

This unit contains a semiconductor laser system and is

classiﬁed as a “CLASS 1 LASER PRODUCT.” So, to

use this model properly, read this Instruction Manual

carefully. In case of any trouble, please contact the store

where you purchased the unit. To prevent exposure to

the laser beam, do not try to open the enclosure.

DANGER:

VISIBLE AND INVISIBLE LASER RADIATION

WHEN OPEN AND INTERLOCK FAILED OR

DEFEATED. DO NOT STARE INTO BEAM.

We,

ONKYO EUROPE

ELECTRONICS GmbH

LIEGNITZERSTRASSE 6,

82194 GROEBENZELL,

GERMANY

declare in own responsibility, that the ONKYO product

described in this instruction manual is in compliance with the

corresponding

technical standards such as EN60065,

EN55013, EN55020 and EN61000-3-2, -3-3.

GROEBENZELL, GERMANY

CAUTION:

I. MORI

ONKYO EUROPE ELECTRONICS GmbH

THIS PRODUCT UTILIZES A LASER. USE OF

CONTROLS OR ADJUSTMENTS OR PERFOR-

MANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARD-

OUS RADIATION EXPOSURE.

Memory backup

The CR-505DAB uses a battery-less memory backup sys-

tem in order to retain radio presets and other settings when

it’s unplugged or in case of a power failure. Although no

batteries are required, the CR-505DAB must be plugged

into an AC outlet in order to charge the backup system.

Once it has been charged, the CR-505DAB will retain the

settings for several weeks, although this depends on the

environment and retention will be shorter in humid cli-

mates. The clock setting is not retained by the backup sys-

tem.

This label is located on the side of the unit. It indicates

that:

1. This unit is a CLASS 1 LASER PRODUCT and

employs a laser inside the cabinet.

2. To prevent the laser from being exposed, do not

remove the cover. Refer servicing to qualiﬁed per-

sonnel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Introduction

DAB

Important Safety Instructions................ 2

Precautions ............................................. 3

Features................................................... 6

Supplied Accessories............................. 6

Before Using the CR-505DAB................ 7

Installing the Remote Controller Batteries...... 7

Using the Remote Controller.......................... 7

Controls & Connectors........................... 8

Front Panel..................................................... 8

Rear Panel ..................................................... 9

Remote Controller ........................................ 10

Using DAB ............................................. 24

Using DAB.................................................... 24

Ensemble Search Mode............................... 24

Component Search Mode ............................ 25

Sorting Components..................................... 25

Sorted List Search Mode.............................. 25

Presetting Components................................ 26

Preset Search Mode..................................... 26

Deleting Presets........................................... 26

Copying Preset Channels............................. 27

Displaying DAB Information ......................... 27

FM/AM

Connections

Using the Radio..................................... 28

Listening to the Radio................................... 28

Tuning the Radio.......................................... 28

Presetting FM Stations Automatically........... 29

Presetting Stations Manually........................ 29

Selecting Presets ......................................... 29

Deleting Presets........................................... 30

Copying Preset Channels............................. 30

RDS (Radio Data System) ........................... 30

Connecting Your Speakers.................. 11

Connecting the Speaker Cords to the

Speaker Connectors .................................. 11

Connecting an Antenna........................ 12

Connecting the Indoor FM Antenna ............. 12

Connecting the AM Loop Antenna ............... 12

Connecting an Outdoor FM Antenna............ 13

Connecting an Outdoor AM Antenna ........... 13

Connecting the DAB Antenna ...................... 13

Connecting Your Other Components to

the CR-505DAB ................................... 14

Before Making Any Connections.................. 14

Using Other Functions

Other Functions .................................... 31

Muting the CR-505DAB................................ 31

Adjusting the Bass & Treble......................... 31

Using Direct Mode........................................ 31

Timers .................................................... 32

About the Timers.......................................... 32

Setting the Timers ........................................ 32

Turning Timers Off ....................................... 34

Checking Timer Settings .............................. 34

Using the Sleep Timer.................................. 34

Connecting

Components........................................ 15

-compatible

Getting Started

Powering Up and Setting the Clock .... 16

Powering Up the CR-505DAB...................... 16

ACCUCLOCK Function................................ 16

Setting the Clock Manually........................... 18

Displaying the Date & Time.......................... 18

Displaying the Time in Standby Mode.......... 18

Using the CR-505DAB .......................... 19

Selecting Sound Sources............................. 19

Adjusting the Volume ................................... 19

Using Headphones....................................... 19

Appendix

Disc Notes ..............................................35

Troubleshooting ....................................37

Specifications ........................................40

CD/MP3 Playback

Playing CDs........................................... 20

Playing CDs.................................................. 20

Selecting Tracks by Number ........................ 20

Displaying Information.................................. 21

Various Playback .................................. 22

Repeat Playback .......................................... 22

Random Playback ........................................ 22

Memory Playback......................................... 23

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

Tuner

Amp

I DAB Tuning

I 25W/Ch into 6 ohms (1 kHz, 10%)

I High Current, Low Impedance Drive

I Discrete Output Stage Circuitry

I Tone Control for Treble and Bass

I Tone Direct

I 59 Presets for DAB

I 40 Presets for AM and FM

I Automatic FM Scan Tuning

I RDS (CT/PS/RT)

I 3 Audio Inputs and 2 Outputs for TAPE, MD, LINE

I Optical Digital Output

Others

I Aluminum Volume Knob & Front Panel

-Compatible Remote Control

CD Player

I 5-Mode Timer (Timer 1, 2, 3, 4/Sleep)

I Plays Music CDs and MP3 CDs

I Wolfson Single-Bit D/A Converter

I 20 Track Memory Playback

Supplied Accessories

Check that the following accessories are supplied with this unit.

FM indoor antenna

AM loop antenna

Remote controller (RC-581S)

two batteries (AAA/R03)

DAB antenna

*In catalogs and on packaging, the letter added to the end of the product name indicates the color of the CR-505DAB. Speciﬁcations and

operation are the same regardless of color.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before Using the CR-505DAB

Installing the Remote Controller

Batteries

Using the Remote Controller

To use the remote controller, point it at the CR-505DAB’s

remote control sensor, as shown below.

Open the battery compartment, as shown.

CR-505DAB

Remote control

sensor

5 m

Insert the two supplied batteries (AAA/

R03) in accordance with the polarity dia-

gram inside the battery compartment.

Notes:

• The remote controller may not work reliably if the CR-

505DAB is subjected to bright light, such as direct sunlight

or inverter type ﬂuorescent lights. Keep this in mind when

installing the CR-505DAB.

• If another remote controller of the same type is used in

the same room, or the CR-505DAB is installed close to

equipment that uses infrared rays, the remote controller

may not work reliably.

• Don’t put anything, such as a book, on the remote con-

troller, because the buttons may be pressed inadvertently,

thereby draining the batteries.

Close the battery compartment.

• The remote controller may not work reliably if the CR-

505DAB is installed in a rack behind colored glass doors.

Keep this in mind when installing the CR-505DAB.

• The remote controller will not work if there’s an obstacle

between it and the CR-505DAB’s remote control sensor.

Notes:

• The supplied batteries should last for about six months,

although this will vary with usage.

• If the remote controller doesn’t work reliably, try replac-

ing both batteries.

• Don’t mix new and old batteries, or different types of bat-

teries.

• If you intend not to use the remote controller for a long

time, remove the batteries to prevent possible leakage and

corrosion.

• Drained batteries should be removed as soon as possible

to prevent possible leakage and corrosion.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controls & Connectors

Front Panel

For detailed information, refer to the pages in parentheses.

Disc Tray

Display

1 2

VOLUME

MIN

MAX

PRESET

STANDBY/ON

BASS

TREBLE

PHONES

INPUT

DIRECT

PUSH TO ENTER

5 6 789 0 A B C

1Remote control sensor (7)

8MENU button (22-30)

Displays the Tuner menu.

Receives control signals from the remote controller.

Selects the play mode for CD or MP3.

2Standby indicator (16)

Lights up when the CR-505DAB is in Standby mode.

9DIRECT button (31)

Used to select “Tone Direct On” or “Tone Direct Off.”

3VOLUME control (19)

Adjusts the volume.

0BASS control (31)

Adjusts the Bass sound while the Tone Direct Off is

selected.

4[ ] button (20)

Opens and closes the disc tray.

ATREBLE control (31)

Adjusts the Treble sound while the Tone Direct Off is

selected.

5STANDBY/ON button (16)

Sets the CR-505DAB to On or Standby.

6PHONES jack (19)

] (PRESET [ / ]) control (20, 23-30)

Used to connect a pair of stereo headphones.

Turn this to select the track, and push to start playing.

You can also select the Preset while the FM or AM is

selected.

7INPUT selector button (19, 28)

Used to select sound sources: CD, DAB, FM, AM,

TAPE, MD or LINE.

CStop [ ] & Play/Pause [ / ] buttons (20)

Used to stop, start, and pause playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controls & Connectors—Continued

Rear Panel

For detailed information, refer to the pages in parentheses.

12 3

5 6 7

SPEAKERS

SUB

OPTICAL

WOOFER

PRE OUT

DIGITAL

OUT

REMOTE

DAB

FM75

CONTROL

ANTENNA

TAPE

OUT

LINE

890

6SUBWOOFER PRE OUT (11)

This RCA/phono connector can be used to connect an

active subwoofer.

REMOTE CONTROL (15)

(Remote Interactive) connector can be con-

This

nected to the

nent. To use

connector on another Onkyo compo-

, you must make an analog RCA/phono

7SPEAKERS (11)

connection between the CR-505DAB and your other

component, even if they are connected digitally.

These terminals are for connecting left and right speakers.

8TAPE IN/OUT (14)

2DAB ANTENNA (13)

These RCA/phono connectors can be used to connect a

cassette tape deck or other recorder with analog inputs

and outputs.

This connector is for connecting the supplied DAB

antenna. CR-505DAB only scans UK Band III.

3FM 75 Ω ANTENNA (12, 13)

9MD IN/OUT (14, 15)

This connector is for connecting an FM antenna.

These RCA/phono connectors can be used to connect a

Mini Disc recorder or other recorder with analog inputs

and outputs.

4AM ANTENNA (12, 13)

These push terminals are for connecting an AM antenna.

0LINE IN (14)

5OPTICAL DIGITAL OUT (14, 15)

These RCA/phono connectors can be used to connect

another component.

This connector can be used to connect a Mini Disc

recorder or other component with digital input.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controls & Connectors—Continued

ACLOCK CALL button— Used to display the current

Remote Controller

time.

BTIMER button— Used to set the timers.

CUp [ ] & Down [ ] buttons— Used to set the tim-

ers.

CLOCK

STANDBY/ON

CALL

DCLEAR button— Used with memory playback.

TIMER

EENTER button— Used to set the timers.

FMODE button— Used to set Random Play or Mem-

ory Play.

GREPEAT button— Used with repeat playback.

CLEAR

MODE

-- ---

ENTER

10/0

HINPUT [ ] [ ] selector buttons— Used to select

sound sources.

DISPLAY

IMUTING button— Used to mute the CR-505DAB.

SLEEP

REPEAT

JPrevious [

] & Next [

] buttons (PRESET

buttons)— Used to select the previous or next track

when playing CDs, or to select presets when using the

radio.

MUTING

INPUT

KDIRECT button— Used to select “Tone Direct On” or

“Tone Direct Off.”

DAB

AM DIRECT

Controlling an Onkyo CassetteTape Deck

An Onkyo Cassette Tape Deck connected via

can be controlled as follows:

(page 15)

1. Use the INPUT [ ]/[ ] selector buttons to select the

TAPE source.

TAPE

2. Use the following buttons.

MUTING

INPUT

[

] .................. Fast reverse

] .................. Fast forward

]..................... Other-side play

RC 581S

DAB

AM DIRECT

[ ] ...................... Stop

[ ]..................... Play

1STANDBY/ON button— Sets the CR-505DAB to On

TAPE

or Standby.

2Number buttons— Used to select CD tracks.

3DISPLAY button— Used to display information.

4SLEEP button— Used with the Sleep function.

Controlling an Onkyo Mini Disc Recorder

An Onkyo Mini Disc Recorder connected via

can be controlled as follows:

(page 15)

5VOLUME UP [ ] & DOWN [ ] buttons— Used

to set the volume.

1. Use the INPUT [ ]/[ ] selector buttons to select the

MD source.

2. Use the following buttons.

6Fast Reverse [ ] & Fast Forward [ ] buttons

(TUNING buttons)— Used for fast reverse and fast

forward when playing CDs, or for tuning when using

the radio.

[

]................... Fast reverse

]................... Fast forward

] .................. Previous track

] .................. Next track

SLEEP

REPEAT

MUTING

INPUT

7AM button— Used to select AM tuner.

8FM button— Used to select FM tuner.

[ ]...................... Pause

[ ] ...................... Stop

DAB

AM DIRECT

9DAB button— Used to select DAB tuner.

0CD control buttons— Used to control CD playback.

[

]..................... Play

[REPEAT].......... Repeat mode

TAPE

Download from Www.Somanuals.com. All Manuals Search And Download.

ConnectingYour Speakers

Before you connect your speakers, read the following:

• Disconnect the power cord from the wall outlet.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals only to positive (+)

terminals, and negative (–) terminals only to negative (–)

terminals. If you get them the wrong way around, the

sound will be out of phase and will sound odd.

Connecting the Speaker Cords to

the Speaker Connectors

Strip 10 mm from the

end of each cord.

10 mm (7/16“)

• Only use speakers with an impedance of 4 ohms or

higher. If you use speakers with a lower impedance, and

use the ampliﬁer at high volume levels for a long period

of time, the built-in protection circuit may be activated.

• Unnecessarily long or very thin speaker cables may affect

the sound quality and should be avoided.

Twist the stripped end

of the cord.

• Be careful not to short the posi-

Push the lever up.

tive and negative connections.

Doing so may damage the CD

Receiver.

• Don’t connect more than one

cable to each speaker terminal.

Doing so may damage the CD

Receiver.

• If you want to connect a single speaker instead of a pair,

connect it to either the left or right speaker terminals, not

both.

Insert the stripped end

of the cord.

SPEAKERS

Press down the lever.

The wire of the stripped

end of the cord should

appear slightly.

SPEAKERS

Powered

subwoofer

LINE INPUT

SUB

WOOFER

PRE OUT

SPEAKERS

SUB

OPTICAL

WOOFER

DIGITAL

OUT

REMOTE

PRE OUT

DAB

FM75

CONTROL

ANTENNA

TAPE

OUT

LINE

The SUBWOOFER PRE OUT should be connected to the

input on your powered subwoofer. If your subwoofer

doesn’t have an amp built-in, you’ll need to use an exter-

nal amp. See the manual supplied with your subwoofer for

more information.

Right

speaker

Left

speaker

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting an Antenna

This chapter explains how to connect the supplied indoor

FM antenna, AM loop antenna, and DAB antenna and how

to connect commercially available outdoor FM and AM

antennas.

Connecting the AM Loop Antenna

The supplied indoorAM loop antenna is for indoor use only.

The CD Receiver won’t pick up any radio signals without

any antenna connected, so you must connect an antenna to

use the tuner.

Assemble the AM loop antenna, inserting

the tabs into the base, as shown.

DAB antenna socket

FM antenna socket

AM antenna push terminals

SPEAKERS

SUB

OPTICAL

WOOFER

DIGITAL

OUT

REMOTE

PRE OUT

DAB

FM75

CONTROL

ANTENNA

Connect both wires of the AM loop

antenna to the AM push terminals, as

shown.

TAPE

OUT

LINE

(The antenna’s wires are not polarity sensitive, so they

can be connected in either push terminal.)

Make sure that the wires are attached securely and that

the push terminals are gripping the bare wires, not the

insulation.

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

Attach the FM antenna, as shown.

Push

Insert wire

Release

FM75

ANTENNA

Once the CD Receiver is ready for use, you’ll need to

tune into an FM radio station and adjust the position of

the FM antenna to achieve the best possible reception.

Once the CD Receiver is ready for use, you’ll need to

tune into an AM radio station and adjust the position of

the AM antenna to achieve the best possible reception.

Keep the antenna as far away as possible from the CD

Receiver, TV, speaker cables, and power cords.

Use thumbtacks or something similar to

ﬁx the FM antenna into position.

If you cannot achieve good reception with the supplied

indoorAM loop antenna, try using a commercially available

outdoor AM antenna (see page 13).

Caution: Be careful that you don’t injure yourself

when using thumbtacks.

If you cannot achieve good reception with the supplied

indoor FM antenna, try using a commercially available out-

door FM antenna instead (see page 13).

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting an Antenna—Continued

Connecting an Outdoor FM Antenna

Connecting an Outdoor AM Antenna

If you cannot achieve good reception with the supplied

indoor FM antenna, try using a commercially available out-

door FM antenna instead.

If good reception cannot be achieved using the suppliedAM

loop antenna, an outdoor AM antenna can be used in addi-

tion to the loop antenna, as shown.

Outdoor antenna

Insulated antenna cable

AM loop antenna

FM75

ANTENNA

Notes:

Outdoor AM antennas work best when installed horizon-

tally outside, but good results can sometimes be obtained

indoors by mounting it horizontally above a window. Note

that the AM loop antenna should be left connected.

Outdoor antennas must be grounded in accordance with

local regulations to prevent electrical shock hazards.

• Outdoor FM antennas work best outside, but usable

results can sometimes be obtained when installed in an

attic or loft.

• For best results, install the outdoor FM antenna well away

from tall buildings, preferably with a clear line of sight to

the transmitter.

• Outdoor antennas should be located away from possible

noise sources, such as neon signs, busy roads, etc.

• For safety reasons, an outdoor antenna should be situated

well away from power lines and other high-voltage

equipment.

Connecting the DAB Antenna

Screw the supplied DAB antenna onto the

DAB connector.

• Outdoor antennas must be grounded in accordance with

local regulations to prevent electrical shock hazards.

I Using a TV/FM Antenna Splitter

It’s best not to use the same antenna for both FM and TV

reception, as this can cause interference problems. If cir-

cumstances demand it, use a TV/FM antenna splitter, as

shown.

Once the CD Receiver is ready for use, you’ll need to

tune into an DAB station and adjust the position of the

DAB antenna to achieve the best possible reception.

TV/FM antenna splitter

Use thumbtacks or something similar to

ﬁx the DAB antenna into position.

To TV (or VCR)

To CD Receiver

Download from Www.Somanuals.com. All Manuals Search And Download.

ConnectingYour Other Components to the CR-505DAB

RCA Connection Color Coding

Before Making Any Connections

RCA-type connections are usually color coded: red and

• Read the manuals supplied with your components.

white. Use red plugs to connect right-channel audio inputs

• Don’t connect the power cord until you’ve completed and

and outputs (typically labeled “R”). Use white plugs to con-

double-checked all connections.

nect left-channel audio inputs and outputs (typically labeled

“L”).

Optical Digital Output

Analog audio

The CD Receiver’s optical digital output has a shutter-type

cover that opens when an optical plug is inserted and closes

when it’s removed. Push a plug in all the way.

Left (white)

Right (red)

Left (white)

Right (red)

• Push plugs in all the way to

make good connections (loose

connections can cause noise or

malfunctions).

Right!

Caution: To prevent shutter damage, hold the optical

plug straight when inserting and removing.

• To prevent interference, keep

audio cables away from power

cords and speaker cables.

Wrong!

Cassette Tape Deck

MD recorder

ANALOG

INPUT OUTPUT

REMOTE

CONTROL

(

)

(

)

PLAY

REC

DIGITAL INPUT

OPTICAL

INPUT OUTPUT

REMOTE

(REC)

(PLAY)

CONTROL

INPUT OUTPUT

(REC) (PLAY)

DIGITAL INPUT

OPTICAL

(REC)

(PLAY)

TAPE

OUT

OPTICAL

OUT

DIGITAL

OUT

SPEAKERS

SUB

OPTICAL

WOOFER

DIGITAL

OUT

REMOTE

PRE OUT

DAB

FM75

CONTROL

ANTENNA

TAPE

OUT

LINE

Note:

If you are using a timer to

start recording on an Onkyo

Mini Disc recorder con-

nected via

, be sure to

connect the recorder’s ana-

log inputs to the CR-

505DAB’s analog outputs.

AUDIO OUT

LINE

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting

-compatible Components

With

(Remote Interactive) you can control your

To use

connector to an

using an

, you need to connect the CR-505DAB’s

compatible Onkyo cassette tape deck or MD recorder with

the CR-505DAB’s remote controller, and use the following

connector on the other component by

cable is supplied with each

cable. An

special

functions:

compatible Onkyo cassette tape deck and MD recorder.

I Auto Power On

When you turn on a component connected via

Hookup Example:

while the

To other

CR-505DAB is in Standby, the CR-505DAB automatically

turns on and selects that component as the input source.

This function doesn’t work if the CR-505DAB is already

on.

-compatible

REMOTE

CONTROL

component

cable

Onkyo MD recorder

I Direct Change

When you press the play button on a component connected

ANALOG

INPUT OUTPUT

REMOTE

CONTROL

via

, the CR-505DAB automatically selects that compo-

(

)

(

)

PLAY

REC

DIGITAL INPUT

OPTICAL

nent as the input source.

I Auto Power Off

When you set the CR-505DAB to Standby, all components

connected via

also enter Standby.

INPUT OUTPUT

(REC) (PLAY)

DIGITAL INPUT

OPTICAL

I Controlling Other Components

Other components can be controlled with the supplied

remote controller (see “Remote Controller” on page 10).

I CD Synchro Recording

An MD recorder or cassette tape deck connected via

and set to record pause, will start recording automatically

when CD playback is started on the CR-505DAB.

OUT

OPTICAL

I Timer

DIGITAL

OUT

The CR-505DAB’s timers can be used to automatically start

playback or recording on a cassette tape deck or MD

recorder connected via

(see “Timers” on page 32).

SPEAKERS

SUB

OPTICAL

WOOFER

REMOTE

DIGITAL

OUT

REMOTE

CONTROL

DAB

FM75

PRE OUT

CONTROL

ANTENNA

I Sleep Timer

When you set the CR-505DAB’s sleep timer, the sleep tim-

ers on component connected via are also set, so all

components switch off after the speciﬁed period.

TAPE

OUT

LINE

CR-505DAB

Notes:

• Use only

• To use

cables for

connections.

you must make an analog RCA/phono con-

nection between the CR-505DAB and the other com-

ponent even if they are connected digitally.

• If a component has two

connectors, you can connect

either one to the CR-505DAB. The other connector is for

connecting additional

• Connect the CR-505DAB’s

-compatible components.

connector only to Onkyo

components. Connecting to other manufacturer’s compo-

nents may cause them to malfunction.

• Some Onkyo

-compatible components may not sup-

port the special functions described above.

Download from Www.Somanuals.com. All Manuals Search And Download.

Powering Up and Setting the Clock

ACCUCLOCK Function

VOLUME

CLOCK

STANDBY/ON

CALL

CLOCK CALL

TIMER

MIN

MAX

TIMER

PRESET

STANDBY/ON

BASS

TREBLE

PHONES

INPUT

DIRECT

PUSH TO ENTER

CLEAR

MODE

-- ---

ENTER

10/0

ENTER

DISPLAY

STANDBY/ON

SLEEP

REPEAT

Standby indicator

MUTING

INPUT

Powering Up the CR-505DAB

DAB

AM DIRECT

Before connecting the power cord, complete all connections

(see pages 11 to 15).

The very ﬁrst time you turn on the CR-505DAB, the

ACCUCLOCK function automatically sets the clock by

using the CT (Clock Time) information present in RDS

radio broadcasts.

While the clock is being set, “Clock Setting” appears on the

display, as shown. It may take a while to set the clock.

Connect the power cord to a suitable wall

outlet.

The CR-505DAB enters Standby mode, and the

Standby indicator comes on.

To turn on the CR-505DAB, press the

[STANDBY/ON] button.

The CR-505DAB comes on, the display lights up, and

the Standby indicator goes off.

To turn off the CR-505DAB, press the [STANDBY/

ON] button again. The CR-505DAB enters Standby

mode and the Standby indicator comes on.

When the clock has been set, “Adjusted” appears on the dis-

play for a while.

Use the [CLOCK CALL] button to check if the clock has

been set correctly.

If the clock has not been set correctly, see “Setting the

Clock Manually” on page 18.

The ACCUCLOCK function automatically calibrates

the clock daily at 2 AM, 3 AM and 2 PM.

If ACCUCLOCK does not stop:

When the radio reception is not good, the ACCUCLOCK

function may not end. To force theACCUCLOCK function

to end, press the [DISPLAY] button. In this case, set the

clock manually.

If the wrong day or time appears on the display:

If you live close to the border with another country, the CT

information may have been taken from a radio station in

another time zone. In this case you should specify another

station and try setting again (see “SettingACCUCLOCK to

Use a Speciﬁc Station” on page 17).

Download from Www.Somanuals.com. All Manuals Search And Download.

Powering Up and Setting the Clock—Continued

I Setting ACCUCLOCK to Use a Speciﬁc

Station

If the wrong time is displayed, you can specify which FM

station the ACCUCLOCK function should use. This must

be an FM station that supports RDS CT (Clock Time) infor-

mation.

I Turning Off ACCUCLOCK

If you don’t wantACCUCLOCK to calibrate the clock auto-

matically at 2 AM, 3 AM and 2 PM everyday, you can turn

it off as follows.

Press the [FM] button to select FM.

Press the [TIMER] button repeatedly until

“Clock” appears on the display, as shown.

Press the [TIMER] button repeatedly until

“Clock” appears.

Press the [ENTER] button.

“Accuclock” appears on the display.

If “Manual Adjust” appears, use the Up/Down [ ]/[ ]

buttons to select “Accuclock.”

Press the [ENTER] button.

“Accuclock” appears on the display.

Press the [ENTER] button.

“Auto” appears on the display.

Use the Up/Down [ ]/[ ] buttons to select

“Manual Adjust.”

Use the Up/Down [ ]/[ ] buttons to select

“Station” and press [ENTER].

Press the [ENTER] button 3 times.

Use the [ ]/[ ] buttons to tune into the

FM station.

The “RDS” indicator appears when tuned into a station

that supports RDS.

Press the [ENTER] button.

While the clock is being set, “Clock Setting” appears

on the display. It may take a few minutes to set the

clock.

When the clock has been set, “Adjusted” appears on

the display for a while.

Notes:

• If the clock has not been set correctly, specify another FM

station and try again, or set the clock manually (see

page 18).

• If you don’t want the clock to be calibrated automatically,

you can turn off theACCUCLOCK function (see the next

section).

Download from Www.Somanuals.com. All Manuals Search And Download.

Powering Up and Setting the Clock—Continued

Press the [ENTER] button.

The time ﬂashes.

CLOCK

STANDBY/ON

CALL

CLOCK CALL

TIMER

Use the Up/Down [ ]/[ ] buttons to set

the time.

CLEAR

MODE

-- ---

ENTER

10/0

ENTER

DISPLAY

SLEEP

REPEAT

MUTING

INPUT

Press the [ENTER] button to set the clock.

“Adjusted” appears on the display.

DAB

AM DIRECT

Displaying the Date & Time

Setting the Clock Manually

Press the [CLOCK CALL] button.

The date and time appear on the display.

Press the [CLOCK CALL] button again to return to the

previous display.

If you cannot set the clock by using theACCUCLOCK

function, you can set it manually. In this case, the

ACCUCLOCK function will not automatically cali-

brate the clock each day.

VOLUME

Press the [TIMER] button repeatedly until

“Clock” appears.

MIN

MAX

PRESET

STANDBY/ON

BASS

TREBLE

PHONES

INPUT

DIRECT

PUSH TO ENTER

STANDBY/ON

Press the [ENTER] button and use the Up/

Down [ ]/[ ] buttons to select “Manual

Adjust.”

Displaying the Time in Standby

Mode

You can set the CR-505DAB so that the time is displayed

while the CR-505DAB is in Standby mode.

With the CR-505DAB turned on, press and

hold the CR-505DAB’s [STANDBY/ON] but-

ton for more than 2 seconds.

Press the [ENTER] button.

To turn off the time display, repeat this procedure.

The day of the week ﬂashes.

Note:

Setting the CR-505DAB to display the time will slightly

increase the power consumption in Standby mode.

Use the Up/Down [ ]/[ ] buttons to select

a day.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the CR-505DAB

VOLUME control

Adjusting the Volume

VOLUME

To adjust the volume, use the [VOLUME]

control, or the remote controller’s VOL-

UME [ ]/[ ] buttons.

MIN

MAX

PRESET

Turn the [VOLUME] control clockwise to increase the

volume; counterclockwise to decrease it.

STANDBY/ON

BASS

TREBLE

PHONES

INPUT

DIRECT

PUSH TO ENTER

Using Headphones

INPUT

You can connect a pair of stereo headphones to the CR-

505DAB’s PHONES jack for private listening, as shown.

CLOCK

CALL

STANDBY/ON

TIMER

CLEAR

MODE

-- ---

ENTER

10/0

DISPLAY

VOLUME UP

SLEEP

REPEAT

STANDBY/ON

PHONES

INPUT

MUTING

INPUT

VOLUME DOWN

DAB

AM DIRECT

TAPE

Note:

Always turn down the volume before connecting your head-

phones.

RC 581S

Selecting Sound Sources

Use the [INPUT] button, or the remote con-

troller’s INPUT [ ]/[ ] buttons to select

one of the following sound sources: CD,

DAB, FM or AM,TAPE, MD, LINE.

The currently selected source is shown on the display.

If you selected CD, see “Playing CDs” on

page 20.

If you select DAB, see “Using DAB” on page 24.

If you selected AM or FM, see “Using the Radio” on

page 28.

If you selected TAPE, MD, or LINE, start playback on

the relevant component.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing CDs

I To Fast Forward or Fast Reverse (remote

controller only)

During playback or while playback is paused, press and

hold the [ ] button to fast forward, or the [ ] button to

fast reverse.

VOLUME

For MP3, fast reverse only works within the MP3 track that

is currently playing.

MIN

MAX

PRESET

STANDBY/ON

BASS

TREBLE

PHONES

INPUT

DIRECT

If you press the button for more than four seconds, the fast

forward or fast reverse speed increases.

PUSH TO ENTER

I To Select Tracks

On the CR-505DAB:

Stop

Play/ Pause

Turn the [

] control to select a track for playback. If

you select a track while playback is stopped, press the

CLOCK

CALL

[

] control to start playback.

STANDBY/ON

Press the [

playback.

] control to jump to the next track during

TIMER

Number

buttons

On the remote controller:

CLEAR

MODE

-- ---

Press the [

button to select the previous track.

If you press the [

] button to select the next track, or the [

]

ENTER

10/0

DISPLAY

--/---

SLEEP

REPEAT

] button during playback or while play-

back is paused, the beginning of the current track is

selected.

MUTING

INPUT

operation

buttons

If you select a track while playback is stopped, press the

Play [ ] button to start playback.

DAB

AM DIRECT

Note:

With CDs and MP3 discs that contain many tracks, play-

back may take a while to start.

TAPE

Selecting Tracks by Number

Playing CDs

You can use the number buttons to select speciﬁc tracks.

Press the [ ] button to open

the disc tray, put the CD on

the tray with the label-side

facing up, and press the [ ]

button again to close the

tray.

Label side

Use the number buttons to enter a track

number. Playback starts automatically.

For MP3 disc, select the serial number assigned to the

track.

To enter a track number smaller than or equal to 10,

press each number button. For example, to enter track

number 10, press [10/0].

Be sure to put 8 cm discs in the center of the tray.

Press the Play [ ] button to start play-

back.

Playback starts and the Play indicator appears on the

display.

Use the [--/---] button to enter track numbers above 10.

To enter a track number from 11 to 99, press

[--/---] once. For example, to enter track number 15,

press [--/---], [1] and [5].

To enter a track number greater than or equal to 100,

press [--/---] twice. For example, to enter tranck num-

ber 123, press [--/---] twice, [1], [2] and [3].

I To Stop Playback

• Press the Stop [ ] button.

I To Pause Playback

• Press the Play/Pause [ / ] button on the CR-505DAB or

Pause [ ] button on the remote controller. The Pause

indicator appears.

• To resume playback, press the Play/Pause [ / ] button on

the CR-505DAB or Play [ ] button on the remote control-

ler.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing CDs—Continued

I MP3 Disc

Elapsed track time: The length of time that the current

track has been playing (default display).

CLOCK

CALL

STANDBY/ON

TIMER

CLEAR

MODE

-- ---

ENTER

10/0

DISPLAY

SLEEP

REPEAT

MUTING

INPUT

Track name: Name of the current track.

DIRECT

Displaying Information

Folder name: Name of the current folder.

This section explains how to display various information,

including the remaining track time, remaining disc time,

and ID3 tag for MP3 tracks.

During playback, press the [DISPLAY] but-

ton repeatedly to cycle through the follow-

ing options.

Title name: Title of the current track (if ID3 tag present).

I Audio CD

Elapsed track time: The length of time that the current

track has been playing (default display).

Notes:

• To display the disc name, while playback is stopped,

press the [DISPLAY] button.

• If a track or folder name contains a character that cannot

be displayed, it will be displayed as “*.”

Remaining track time: The amount of time remaining for

the current track (“R” indicator appears).

Remaining disc time: The amount of time remaining for

the entire disc (“T” indicator appears).

Download from Www.Somanuals.com. All Manuals Search And Download.

Various Playback

VOLUME

CLOCK

CALL

STANDBY/ON

TIMER

Number

buttons

MIN

MAX

PRESET

STANDBY/ON

BASS

TREBLE

PHONES

INPUT

DIRECT

CLEAR

ENTER

--/---

CLEAR

MODE

-- ---

ENTER

10/0

PUSH TO ENTER

DISPLAY

MODE

SLEEP

REPEAT

Play/ Pause

MUTING

INPUT

Random Playback

DAB

AM DIRECT

With the Random function you can play tracks in random

order.

Repeat Playback

While stopped, press the remote control-

ler’s [MODE] button repeatedly to display

“D-Rdm” indicator.

With the Repeat function you can play a track, a folder or a

disc repeatedly.

During playback, press the remote con-

troller’s [REPEAT] button repeatedly to

select repeat mode.

D-Rpt: Repeat the disc

Press the Play [ ] button to start random

playback.

All tracks are played in random order.

To cancel random playback, stop play-

back, and then press the [MODE] button

repeatedly until the “Rdm” indicator dis-

appears.

T-Rpt: Repeat current track

Note:

When carrying out operations on the CR-505DAB, press

the [MENU] button repeatedly to select the RANDOM

mode, and then press the Play/Pause [ / ] button to start

random playback.

F-Rpt: Repeat current folder (MP3 only)

To cancel Repeat playback, press the

[REPEAT] button repeatedly to turn off the

“Rpt” indicator.

Note:

If you press the [REPEAT] button during memory playback,

your custom program will play repeatedly.

Download from Www.Somanuals.com. All Manuals Search And Download.

Various Playback—Continued

Memory Playback

With the Memory function you can make a custom program

of your favourite tracks.

While stopped, press the remote control-

ler’s [MODE] button repeatedly until the

“Mem” indicator appears on the display.

To add a track to your program, use the

[

]/[ ] buttons to select it, and then

press the [ENTER] button.

You can add up to 20 tracks to your program.

Tracks can also be added by using the number buttons.

For information on using the number buttons to select a

track, see “Selecting Tracks by Number” on page 20.

You can check which tracks you’ve added to the pro-

gram by using the [ ]/[ ] buttons.

To start memory playback, press the Play

[ ] button.

Memory playback stops automatically when all the

tracks in the program have been played.

Note:

When carrying out operations on the CR-505DAB, press

the [MENU] button repeatedly to turn on the “Mem” indi-

cator, turn the [

] control to select a track, and press

the [

] control to register. To start memory playback,

press the Play/Pause [ / ] button.

I To Stop Memory Playback

Press the Stop [ ] button.

I To Remove the Last Track in the Program

While memory playback is stopped, press the [CLEAR]

button. Each time you press it the last track in the program

is removed.

I To Cancel Memory Playback

While memory playback is stopped, press the [MODE] but-

ton repeatedly until the “Mem” indicator disappears. The

entire program will be deleted.

Notes:

• If the total playing time of your program exceeds 99 min-

utes and 59 seconds, “--:--” is displayed. (This does not

affect program playback.)

• The program is deleted when the disc tray is opened.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using DAB

You can use the Auto Tuning function manually:

You may want to re-tune at a later date if you move the CR-

505DAB or if you want to receive a newly introduced

ensemble.

VOLUME

MIN

MAX

1. Press the [MENU] button.

PRESET

STANDBY/ON

BASS

TREBLE

PHONES

INPUT

DIRECT

2. Turn the [

push the [

] control to select “Auto Tuning” and

] control.

PUSH TO ENTER

3. The Auto Tuning starts and scans the Band III frequen-

cies. The number of scanned components are shown dur-

ing scanning.

INPUT

Notes:

CLOCK

CALL

STANDBY/ON

• You can also control this function using the [MODE],

TIMER

PRESET [

]/[

] and [ENTER] buttons on the

remote controller.

• During BAND III scanning, the DAB only scans the

audio services in the 174.928-239.200 MHz band range.

CLEAR

MODE

-- ---

ENTER

10/0

ENTER

MODE

DISPLAY

About secondary service:

SLEEP

REPEAT

If a secondary service exists, the “>>” symbol will light up

in the “Ensemble No. & Freq.” Press the [ENTER] button to

select the secondary service.

While the secondary service is selected, the “<<” symbol

will light up on the display. Press the [ENTER] button to go

back to the primary service.

MUTING

INPUT

PRESET

DAB

AM DIRECT

DAB

TAPE

Ensemble Search Mode

Using DAB

You can select any frequency (ensemble) scanned by using

the Auto Tuning function.

Press the [DAB] button on the remote con-

troller, or press the [INPUT] button on the

CR-505DAB repeatedly to select DAB

input.

Press the [MENU] button.

Turn the [

] control to select “Search

Mode” and push the [

] control.

Turn the [

] control to select“Ensem-

ble” and push the [

] control.

Using the DAB for the ﬁrst time:

When you ﬁrst switch on the unit and select DAB, the Auto

Tuning function scans the Band III frequencies.

After the scanning, the ﬁrst scanned component will be

selected and you will hear it through your speakers.

To listen to other stations, use one of the search modes

shown below.

Turn the [

ensemble.

] control to select an

• Ensemble search mode: Selects the frequency (Ensem-

ble) (Page 24).

• Component search mode: Searches the components

(Page 25).

• Sorted List search mode: Searches in the sorted order in

the selected sort mode (Page 25).

• Preset search mode: Searches the preset components

(Page 26).

Download from Www.Somanuals.com. All Manuals Search And Download.

Using DAB—Continued

Component Search Mode

Sorted List Search Mode

You can select a component for listening from the list of

scanned components produced by using the Auto Tuning

function.

You can select any component for listening from the list of

sorted components.

Press the [MENU] button.

Turn the [

] control to select“Search

Turn the [

] control to select“Search

Mode” and push the [

] control.

Mode” and push the [

] control.

Turn the [

] control to select “Sorted

Turn the [

] control to select “Com-

List” and push the [

] control.

ponent” and push the [

] control.

Turn the [

] control to select a com-

Turn the [

] control to select the com-

ponent and push the [

You can select any component from the sorted list.

] control.

ponent you require.

You can select any component outside the ensemble.

Sorting Components

You can sort and list scanned components by component

name, program type or alphabetical order.

You can then select the component you want to listen to

from the list.

• Component Name

Sorts the components for each ensemble by component

name.

• PTY

Sorts components by program type.

• Alphabet

Sorts component names in alphabetical order.

Press the [MENU] button.

Turn the [

] control to select “Sort

Mode” and push the [

] control.

Turn the [

] control to select the sort

mode required and push the [

trol.

Components are sorted in the sort mode selected.

] con-

Download from Www.Somanuals.com. All Manuals Search And Download.

Using DAB—Continued

VOLUME

Preset Search Mode

You can select previously stored presets as follows.

MIN

MAX

Press the [MENU] button.

PRESET

STANDBY/ON

BASS

TREBLE

PHONES

INPUT

DIRECT

PUSH TO ENTER

Turn the [

] control to select“Search

Mode” and push the [

] control.

Turn the [

] control to select“Preset”

and push the [

] control.

CLOCK

CALL

STANDBY/ON

TIMER

CLEAR

MODE

-- ---

ENTER

REPEAT

10/0

ENTER

MODE

DISPLAY

SLEEP

MUTING

INPUT

Turn the [

] control to select a preset.

PRESET

Deleting Presets

DAB

AM DIRECT

You can delete unwanted presets as follows.

Select the preset that you want to delete.

TAPE

Press the [MENU] button.

Presetting Components

Turn the [

] control to select “Preset

You can preset up to 59 of your favourite DAB components.

Edit” and push the [

] control.

Search for your favourite DAB component.

Turn the [

] control until “Preset

Press the [MENU] button.

Erase?” appears on the display.

Turn the [

] control to select “Preset

Edit” and push the [

] control.

Turn the [

] control to select “Preset

Write?” and push the [

The preset number ﬂashes.

] control.

Push the [

] control.

The selected preset is deleted.

While the preset number is ﬂashing, use

the [

] control to select a preset num-

ber from 1 to 59.

Press the [

] control to store the sta-

tion.

Repeat this procedure to store all your favourite sta-

tions in the presets.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using DAB—Continued

3. Bit Rate + mono/stereo

Copying Preset Channels

Displays the current station mode (stereo or mono) and the

bit rate at which the audio signal is being transmitted. This

rate is set by the broadcaster to suit the type and quality of

material being transmitted.

You can copy a preset channel to another channel.

Select the preset that you want to copy.

Press the [MENU] button.

Turn the [

] control to select “Preset

Edit” and push the [

] control.

4. Bit Error Rate

Turn the [

] control until “Preset

Noise may be generated and reception quality may become

poor at bit error rates above 0.1. If a rate above 0.1 is dis-

played, move the antenna in different directions to ﬁnd a

position where the rate displayed is less 0.1.

Copy?” appears on the display.

Push the [

] control.

The preset number ﬂashes.

5. DLS (Data Label Service)

Displays any scrolling text transmitted with the audio sig-

nal.

While the preset number is ﬂashing, use

the [

] control to select a preset num-

ber from 1 to 59.

Push the [

] control.

The station is copied to another channel and the preset

number stops ﬂashing.

6. Ensemble Name

Displays the ensemble name.

Displaying DAB Information

Press the [DISPLAY] button repeatedly to cycle through the

seven different display modes.

1. P-Type (Service Components)

Displays a description of the program type being broadcast

by the station.

7. Ensemble No. & Freq

Displays the ensemble number and frequency for the station

to which you are tuned.

2. Time

Displays the date and time obtained from the current com-

ponent.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Radio

I Tuning into weak FM stations

VOLUME

If a station has poor signal strength, you may not be able to

tune into that station properly, or reception may be noisy. In

this case, switch the FM Mode to Mono, then tune the band.

MIN

MAX

Switching the FM Mode to Mono:

PRESET

STANDBY/ON

BASS

TREBLE

PHONES

INPUT

DIRECT

PUSH TO ENTER

Press the [MODE] button.

INPUT

Use the [ ]/[ ] buttons to display “FM

Mode” and press [ENTER].

CLOCK

CALL

STANDBY/ON

Use [ ]/[ ] to display “Mono” and

press [ENTER].

The “ST” (FM stereo) indicator goes off and mono

mode is selected.

TIMER

CLEAR

MODE

-- ---

ENTER

10/0

Using the buttons on the CR-505DAB:

1. Press the [MENU] button.

ENTER

MODE

DISPLAY

SLEEP

REPEAT

2. Turn the [

] control until “FM Mode” appears on

INPUT

TUNING

MUTING

INPUT

the display and push the [

] control.

3. Turn the [

display and push the [

] control until “Mono” appears on the

PRESET

] control.

DAB

AM DIRECT

TAPE

Listening to the Radio

Press the [AM] or [FM] button to select AM

or FM. Or use the [INPUT] button, or the

remote controller’s INPUT [ ]/[ ] buttons

to select AM or FM.

Tuning the Radio

Press and hold the TUNING [ ] or [

]

button on the remote controller for more

than one second and then release it.

The CR-505DAB searches for the next station. Search-

ing stops when a station is found.

Use the TUNING [ ]/[ ] buttons for ﬁne

tuning.

Note:

You can tune the radio with the remote controller only.

If you select the FM band:

When you’re tuned into a station, the Tuned

(FM stereo) indicators appear.

and “ST’

The FM band is searched in 0.05 MHz intervals.

If you select the AM band:

When you’re tuned into a station, the Tuned

appears.

indicator

The AM band is searched in 9 kHz intervals.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Radio—Continued

Presetting FM Stations Automatically

Use the [ ]/[ ] buttons to display “Pre-

set Write?,” and then press the [ENTER]

button.

With the Auto Preset function you can automatically preset

all the FM stations available in your area.

The preset number ﬂashes.

Press the [FM] button.

Press the [MODE] button.

Use the [ ]/[ ] buttons to display “Pre-

set Edit,” and then press the [ENTER] but-

ton.

While the preset number is ﬂashing, use

the [ ]/[ ] buttons to select a preset

number from 1 to 40.

You cannot choose any preset number that has already

been registered for either the FM or AM station.

Use the [ ]/[ ] buttons to display“Auto

Preset?,” and then press the [ENTER] but-

ton.

Press the [ENTER] button to store the sta-

tion.

The station is stored and the preset number stops ﬂash-

ing.

Repeat this procedure for all of your favourite radio

stations.

Auto Preset function starts.

The Auto Preset function scans the FM band from low

to high, presetting up to 30 stations with strong signals.

Note:

When the CR-505DAB is tuned into a station that’s trans-

mitting PS (Program Service Name) RDS information, the

station’s name will be displayed instead of the frequency.

Note:

All previously stored presets will be overwritten when the

Auto Preset function is used again.

Using the buttons on the CR-505DAB:

1. Tune into the station that you want to store as a preset.

2. Press the [MENU] button.

Using the buttons on the CR-505DAB:

1. Use the [INPUT] button to select FM.

2. Press the [MENU] button.

3. Turn the [

] control until “Preset Edit” appears on

3. Turn the [

] control until “Preset Edit” appears on

the display and then push the [

] control.

the display and then push the [

] control.

4. Turn the [

on the display and push the [

] control until “Preset Write?” appears

4. Turn the [

on the display and then push the [

] control until “Auto Preset?” appears

] control.

5. While the preset number is ﬂashing, use the [

control to select a preset number from 1 to 40.

]

Presetting Stations Manually

6. Press the [

] control to store the station.

You can preset up to 40 of your favourite AM and FM radio

stations.

Selecting Presets

You can select previously stored presets as follows.

Tune into the station that you want to store

as a preset.

Using the CR-505DAB

Turn the [

] control to select presets.

Press the [MODE] button.

Using the remote controller

Use the [ ]/[ ] buttons to display “Pre-

set Edit,” and then press the [ENTER] but-

ton.

Use the PRESET [ ]/[ ] buttons to

select presets.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Radio—Continued

Deleting Presets

While the preset number is ﬂashing, use

the [ ]/[ ] buttons to select a preset

number from 1 to 40.

You can delete unwanted presets as follows.

Select the preset that you want to delete.

Press the [MODE] button and use the [ ]/

Press the [ENTER] button.

The station is copied to another channel and the preset

number stops ﬂashing.

[

] buttons to display “Preset Edit.”

Using the buttons on the CR-505DAB:

1. Select the preset that you want to copy.

2. Press the [MENU] button and turn the [

until “Preset Edit” appears on the display.

3. Push the [

4. Turn the [

Press the [ENTER] button.

] control

Use the [ ]/[ ] buttons to display “Pre-

set Erase?.”

] control.

] control until “Preset Copy?” appears

on the display.

5. Push the [

] control.

6. While the preset number is ﬂashing, use the [

control to select a preset number from 1 to 40.

]

7. Push the [

] control.

Press the [ENTER] button.

The selected preset is deleted and its number disap-

pears from the display.

RDS (Radio Data System)

The Radio Data System (RDS) allows FM radio stations to

broadcast various information to RDS-compatible radios,

including the name of the radio station and information

about the program being broadcast. Many FM stations in

most European countries transmit RDS information.

The CR-505DAB supports the following RDS information:

PS: Program Service Name

When tuned into a station that transmits PS information, the

station’s name appears on the display.

RT: Radio Text

Using the buttons on the CR-505DAB:

1. Select the preset that you want to delete.

2. Press the [MENU] button and turn the [

until “Preset Edit” appears on the display.

3. Push the [

4. Turn the [

] control

] control.

] control until “Preset Erase?” appears

on the display.

5. Push the [

] control.

When tuned into a station that transmits RT information,

any text messages received appear on the display.

Copying Preset Channels

You can copy a preset channel to another channel.

When the CR-505DAB is tuned into a station that’s trans-

mitting RDS information, the RDS indicator appears on the

display.

To display the PS and RT information, press the [DIS-

PLAY] button repeatedly to select Frequency display, PS, or

RT, as shown.

Select the preset that you want to copy.

Press the [MODE] button and use the [ ]/

[

] buttons to display “Preset Edit.”

Press the [ENTER] button.

Frequency

PS (Program Service Name)

RT (Radio Text)

Use the [ ]/[ ] buttons to display “Pre-

set Copy?.”

When the CR-505DAB receives RT information, “Please

wait” appears on the display ﬁrst, and then the received text

scrolls across the display.

Press the [ENTER] button.

The preset number ﬂashes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Other Functions

Adjusting the Bass & Treble

VOLUME

With the Bass and Treble functions you can adjust the tone

of the sound to your personal preference.

MIN

MAX

PRESET

STANDBY/ON

BASS

TREBLE

PHONES

INPUT

DIRECT

Press the [DIRECT] button to select“Tone

Direct Off.”

PUSH TO ENTER

DIRECT

TREBLE

BASS

CLOCK

STANDBY/ON

CALL

TIMER

Use the [BASS] or [TREBLE] control on

the CR-505DAB to adjust the bass or tre-

ble.

CLEAR

MODE

-- ---

ENTER

10/0

DISPLAY

VOLUME UP

SLEEP

REPEAT

MUTING

Using Direct Mode

MUTING

INPUT

In Direct mode, the bass and treble tone circuits are

bypassed, creating a shorter signal path for a purer sound.

VOLUME DOWN

DIRECT

DAB

AM DIRECT

Press the [DIRECT] button to select“Tone

Direct On.”

TAPE

Muting the CR-505DAB

With this function you can temporarily mute the output of

the CR-505DAB.

To turn off Direct mode, press the

[DIRECT] button again to select “Tone

Direct Off.”

Press the remote controller’s [MUTING]

button.

The output is muted and “Muting” ﬂashes on the dis-

play.

To unmute the CR-505DAB, press the

[MUTING] button again, or adjust the

remote controller’s volume [ ]/[ ] but-

tons.

The output is unmuted and “Muting” goes off.

Note: The Mute function is cancelled when the CR-

505DAB is set to Standby.

Download from Www.Somanuals.com. All Manuals Search And Download.

Timers

About the Timers

CLOCK

CALL

STANDBY/ON

The CR-505DAB has four timers so that you can turn it on

and off automatically at certain times and on certain days of

the week, in order to listen to, or record your favourite pro-

grams.

Timers can be used to start and stop playback (Play), or to

start and stop radio or LINE input recording (Rec) with an

Onkyo cassette tape deck or Mini Disc recorder connected

TIMER

ENTER

CLEAR

MODE

-- ---

ENTER

REPEAT

10/0

DISPLAY

SLEEP

via

Timers can be set for single use (Once), in which case the

timer is reset once the task has been completed, for use on a

certain day every week (Every), or for a range of days (e.g.,

Monday through Friday).

Setting the Timers

The timers are set using the remote controller.

You must set the clock (page 16) before you can set the timers.

To use a timer to turn on the radio, you must ﬁrst preset

some radio stations (see pages 26 and 29).

When the CD is selected for the input source, the timer can-

not be set without a disc placed on the disc tray. This avoids

forgetting to load a disc.

I Timer Examples

The following examples highlight some of the ways in

which you can use the timers.

Timer 1: To wake up to your favourite radio station (preset

#1) every morning, set as follows:

PLAY➔FM 1➔EVERY➔EVERY DAY➔ON 7:00➔OFF

7:30

Press the [TIMER] button repeatedly to

select Timer #1, #2, #3, or #4, and then

press the [ENTER] button.

(If you want a radio alarm only on weekdays, select “Days

Set” instead of “Every Day” and specify “MON–FRI.”)

Timer 2: To record a radio program (preset #2) on the cas-

sette tape deck only this Sunday, set as follows:

REC➔FM 2➔TAPE➔ONCE➔SUN➔ON 21:00➔OFF 22:00

(You need an Onkyo cassette tape deck to do the recording.)

I Timer Overlap

If two or more timers are set to the same ON time, the timer

with the lowest number has priority. For example, if Timer

#1 and Timer #2 are both set to an ON time of 7:00, Timer

#1 has priority and Timer #2 is ignored.

Timer 1: 07:00 - 13:00 (This timer has priority.)

Timer 2: 07:00 - 12:30

Use the Up/Down [ ]/[ ] buttons to select

“PLAY” or “REC,” and then press

[ENTER].

If the settings of two timers overlap, the earlier timer has

priority.

Timer 1: 9:00 - 10:00

Timer 2: 8:00 - 10:00 (This timer has priority.)

Notes:

• The timers work only if the CR-505DAB is in Standby

mode. If the CR-505DAB is on when a timer is supposed

to start playback or recording, nothing will happen, so be

sure to switch the CR-505DAB to Standby mode.

• While a timed recording task is in progress, the output of

the CR-505DAB is muted. To hear what’s being

recorded, press the [MUTING] button to cancel the Mute

function. Press it again to mute the CR-505DAB.

Use the Up/Down [ ]/[ ] buttons to select

the input source, and then press [ENTER].

For timed playback you can select any input source. For

timed recording you can select DAB, AM, FM, or LINE.

If you select DAB, AM or FM, use the Up/Down [ ]/[

buttons to select a preset, and then press [ENTER].

]

When you select “REC” in step 2:

Use the Up/Down [ ]/[ ] buttons to select either

“TAPE” or “MD” for the recording medium, and then

press [ENTER].

Download from Www.Somanuals.com. All Manuals Search And Download.

Timers—Continued

Use the Up/Down [ ]/[ ] buttons to select

“Once” or “Every,” and then press

[ENTER].

Use the [ ]/[ ] buttons to set the OFF

time, and then press [ENTER].

Once: For single use.

Every: For weekly use.

Use the Up/Down [ ]/[ ] buttons to select

“Timer ON,” and then press [ENTER].

The TIMER indicator appears, as shown.

Use the Up/Down [ ]/[ ] buttons to select

one of the following options, and then

press [ENTER].

SUN (Sunday)

FRI (Friday)

SAT (Saturday)

Every Day

MON (Monday)

TUE (Tuesday)

WED (Wednesday)

THU (Thursday)

Days Set

Press the [STANDBY/ON] button to set the

CR-505DAB to Standby mode.

The “Every Day” and “Days Set” (speciﬁes a range of

days) options only appear if you select “Every” in step

If you use any

-connected cassette tape deck or MD

recorder as a recording device, you must also set the

device to standby mode.

If you select “Days Set,” use the Up/Down [ ]/[ ]

buttons to select the ﬁrst day, and then press

[ENTER].

Notes:

• You can cancel the timer setting procedure at any time by

pressing the [TIMER] button.

• If you’re using a timer to start playback, be sure to set the

volume to a suitable level. If the [VOLUME] control is

set to minimum, you won’t hear anything when the timed

playback task starts.

• If you set the playback source to CD, don’t forget to load

a CD into the CR-505DAB before setting it to Standby

mode.

Use the Up/Down [ ]/[ ] buttons to select the last

day, and then press [ENTER].

• If you’re using a timer to start recording on an Onkyo cas-

sette tape deck connected via

, be sure to select the

correct input source on the cassette tape deck, and load a

cassette tape before switching the CR-505DAB to

Standby mode.

• If you’re using a timer to start recording on an Onkyo

Mini Disc recorder connected via

, be sure to connect

the recorder’s analog inputs to the CR-505DAB’s analog

outputs. And be sure to select the correct input source on

the MD recorder.

• For timed recording, it’s a good idea to set the start time

a little before the actual start time of the program that you

intend to record.

Use the [ ]/[ ] button to set the ON time,

and then press [ENTER].

After the ON time has been set, the OFF time is auto-

matically set to one hour later.

Download from Www.Somanuals.com. All Manuals Search And Download.

Timers—Continued

Using the Sleep Timer

CLOCK

CALL

STANDBY/ON

With the sleep timer you can set the CR-505DAB so that it

automatically turns off after a speciﬁed period.

TIMER

ENTER

Press the [SLEEP] button repeatedly to

select the required sleep time.

CLEAR

MODE

-- ---

ENTER

10/0

DISPLAY

With the [SLEEP] button you can set the sleep time

from 90 to 10 minutes in 10 minute increments.

The SLEEP indicator appears on the display when the

sleep timer has been set, as shown. The speciﬁed sleep

time appears on the display for about ﬁve seconds, then

the previous display reappears.

SLEEP

REPEAT

SLEEP

MUTING

INPUT

Turning Timers Off

Sleep indicator

You can turn timers on or off as necessary. This can be use-

ful when, for example, you’re on holiday and you don’t

want to be woken up by the timer that you normally use as

an early-morning radio alarm.

Press the [TIMER] button repeatedly to

select the timer that you want to turn off.

To cancel the sleep timer, press the [SLEEP] button

repeatedly until the SLEEP indicator disappears.

To check the remaining sleep time, press the

[SLEEP] button. Note that if you press the [SLEEP]

button while the sleep time is being displayed, you’ll

shorten the sleep time by 10 minutes.

Use the Up/Down [ ]/[ ] buttons to select

“Timer OFF.”

The timer is turned off, and the previous display reap-

pears after two seconds.

To turn a timer back on again, repeat this procedure

and use the Up/Down [ ]/[ ] buttons to select “Timer

ON.”

Checking Timer Settings

You can check a timer’s settings as follows.

Press the [TIMER] button repeatedly to

select the timer that you want to check.

Press the [ENTER] button repeatedly to

cycle through the timer’s settings.

Note:

You can edit the selected timer’s settings as you check them.

To do this, use the Up/Down [ ]/[ ] buttons to edit the cur-

rently displayed setting, and then press [ENTER] to move

on to the next setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

Disc Notes

Supported Discs

Discs Made on Personal Computers

The CR-505DAB supports the following discs.

Discs made on personal computers, including those of a

compatible format, may not work properly in the CR-

505DAB because of incorrect settings in the disc burning

software. Check the manual supplied with your disc burning

software for additional compatibility information.

Disc

Logo

Format or ﬁle type

PCM

Audio CD

MP3 Compatibility

Audio CD, MP3

MP3

• MP3 discs must be ISO 9660 Level 1 or Level 2, Romeo

or Joliet compliant. Supported formats: Mode 1, Mode 2

XA Form 1.

CD-R

• Folders can be up to eight levels deep.

• MP3 ﬁles must be MPEG-1/MPEG-2 Audio Layer 3 for-

mat with a sampling rate of between 16 kHz and 48 kHz

and a bit-rate of between 32 kbps and 320 kbps (128 kbps

or 192 kbps recommended). Incompatible ﬁles cannot be

played.

• Fixed bit-rate MP3 ﬁles are recommended, however, vari-

able bit-rate (VBR) MP3 ﬁles between 8 kbps and 320

kbps are supported (Playing times may display incor-

rectly).

• MP3 ﬁles must have a “.mp3” or “.MP3” ﬁle name exten-

sion. MP3 ﬁles without the proper extension will not be

recognized. To prevent noise and malfunction, do not use

these extensions for other types of ﬁles.

• The CR-505DAB supports up to 500 MP3 ﬁles and up to

200 folders per disc. (In this case, Disc and File names

contain 30 characters and Folder names contain 20 char-

acters.) Files and folders in excess of this cannot be

played. Note that if the ﬁle and folder structure is very

complicated, the CR-505DAB may not be able to read or

play all of the MP3 ﬁles on the disc. If the disc, folder or

ﬁle names contain many characters, the CR-505DAB

may not support 500 MP3 ﬁles.

Audio CD, MP3

MP3

CD-RW

Audio CD (Session 1),

MP3 (Session 2)

CD Extra

• Some audio CDs use copy protection that doesn’t con-

form to the ofﬁcial CD standard. Since these are non-

standard discs, they may not play properly in the CR-

505DAB.

• The CR-505DAB supports CD-R and CD-RW discs.

However, some CD-R and CD-RW discs may not work

properly for any of the following reasons: disc burner

characteristics, disc characteristics, the disc is damaged

or dirty. See the manual supplied with your disc burner

for more information. Condensation or dirt on the optical

pickup lens can also affect playback.

• The CR-505DAB supports 8 cm and 12 cm discs.

• Playback is not available for DTS CD.

• The CR-505DAB does not support disc types not listed.

• Don’t use discs with an unusual shape, such as those

shown below, because you may damage the CR-

505DAB.

• Disc names may contain up to 30 characters. File and

folder names may contain up to 60 characters.

• The maximum time that can be displayed for a single

track is 99 minutes and 59 seconds.

• The remaining time cannot be displayed when playing

MP3 ﬁles.

• Multisession discs are supported, however, some mul-

tisession discs may take a long time to load and some may

not load at all. When burning CDs we recommend that

you use a single session (disc-at-once), and select “Disc

Close.”

• The ID3 tag version 1.0 is supported.

• Don’t use discs that have residue from adhesive tape,

rental discs with peeling labels, or discs with custom-

made labels or stickers. Doing so may damage the CR-

505DAB and you may not be able to remove the disc

properly.

Notes:

• With CD-ROM, CD-R, and CD-RW discs that contain

many ﬁles and folders, and ﬁles other than MP3s, it may

take a long time to read the disc. We recommend that you

include only MP3 ﬁles on your discs, use about 20 fold-

ers, and limit folder nesting to three levels deep.

• In this manual, MP3 ﬁles are referred to as tracks.

Download from Www.Somanuals.com. All Manuals Search And Download.

Disc Notes—Continued

Handling Discs

• Never touch the underside of a disc.Always hold discs by

the edge, as shown.

Underside

• Never attach adhesive tape or sticky labels to discs.

Cleaning Discs

• For best results, keep your discs clean. Fingerprints and

dust can affect the sound quality and should be removed

as follows. Using a clean soft cloth, wipe from the center

outwards, as shown. Never wipe in a circular direction.

✔

• To remove stubborn dust or dirt, wipe the disc with a

damp soft cloth, and then dry it with a dry cloth.

• Never use solvent-based cleaning ﬂuids, such as thinner

or benzene, commercially available cleaners, or antistatic

sprays intended for vinyl records, because they may dam-

age the disc.

Storing Discs

• Don’t store discs in places subject to direct sunlight, or

near heat sources.

• Don’t store discs in places subject to moisture or dust,

such as in a bathroom or near a humidiﬁer.

• Always store discs in their cases and vertically. Stacking,

or putting objects on unprotected discs may cause warp-

ing, scratches, or other damage.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If you have any trouble using your CR-505DAB, check the following table for possible causes and remedies. If you still can’t

resolve the issue yourself, please contact your Onkyo dealer.

Trouble

Possible Cause

Remedy

Can’t turn on the CR-

505DAB?

Connect the power cord properly to a suitable

wall outlet (page 16).

The power cord is not connected properly.

Check the speaker connections and make sure

The speaker cables are not connected prop- that none of the wires are touching each other,

erly.

other connectors, or any metal parts

(page 11).

The volume is set at minimum.

The CR-505DAB is muted.

Turn up the volume (page 19).

There’s no sound coming

from the speakers?

Unmute the CR-505DAB (page 31).

Turn down the volume, then disconnect the

headphones (page 19).

A pair of headphones is connected.

The wrong input source is selected.

A connecting cable may be damaged.

Check the input source setting (page 19).

Check your connecting cables for signs of

damage and replace as necessary.

Check the speaker connections and make sure

Sound is coming from only The other speaker’s cable is not connected that none of the wires are touching each other,

one speaker?

properly.

other connectors, or any metal parts

(page 11).

The batteries are used.

Replace with new batteries (page 7).

Check the batteries and correct as necessary

(page 7).

The batteries are installed incorrectly.

The remote controller

doesn’t work?

You’re not pointing the remote controller at Point the remote controller at the CR-

the CR-505DAB’s remote sensor.

505DAB’s remote sensor (page 7).

Make sure that the CR-505DAB is not sub-

jected to direct sunshine or inverter-type ﬂuo-

rescent lights. Relocate if necessary.

A strong light source is interfering with the

CR-505DAB’s remote sensor.

AM reception is hindered

by a buzzing noise, espe-

Relocate your AM antenna.

Interference caused by electrical equip-

cially at night or with weak ment, including ﬂuorescent lights.

signals?

Install an outdoor AM antenna (page 13).

Move the AM loop antenna as far away as

possible from your TV.

AM reception is hindered

Interference caused by your TV.

by a high-pitched noise?

Move the CR-505DAB as far away as possi-

ble from your TV.

Install an outdoor antenna as far away as pos-

sible from nearby roads.

Interference is being caused by ﬂuorescent

Reception is hindered by a

Move your antenna as far away as possible

from ﬂuorescent lights.

lights being turned on or off, or by the igni-

crackling noise?

tion systems of passing cars.

Adjust the position or direction of your out-

door antenna.

FM reception and stereo

separation are poor even

though the Tuning and

“ST” (FM stereo) indica-

tors are shown.

Tall buildings, mountains, or hills are caus-

ing wave reﬂections that interfere with the Try an FM antenna with better directionality.

main signal.

The station’s signal is too strong.

Try an indoor FM antenna.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting—Continued

Trouble

Possible Cause

Remedy

Switch the FM Mode to Mono (page 28).

Adjust the position, height, and direction of

your FM antenna.

You’re too far away from the transmitter.

Or, your FM antenna is in the wrong posi-

tion or pointing in the wrong direction. Or,

the station’s signal strength is poor.

Reception is noisy, inter-

mittent, and the “ST” (FM

stereo) indicator ﬂickers?

Install an outdoor FM antenna, preferably

one with many elements. Installing an out-

door antenna is a specialist’s job, so contact

your nearest dealer for advice (page 13).

Preset your favourite radio stations again

The power cord has not been connected to a (pages 26 and 29). The power cord must be

wall outlet, or the power has been turned off plugged into a wall outlet a few times each

The radio presets no longer

work?

for an extended period.

month in order to preserve the presets

(page 4).

The current FM station does not support

RDS.

Tune into a station that supports RDS

(page 30).

The RDS (Radio Data Sys-

tem) doesn’t seem to work?

Install an outdoor FM antenna (page 13),

change the position or direction of your out-

door FM antenna, and keep it away from ﬂu-

orescent lights.

The signal strength is poor, or there’s too

much interference.

Install the CR-505DAB somewhere free of

vibration.

The CR-505DAB is subject to vibration.

CD playback skips?

Noise is generated.

The disc is dirty.

Remove the disc and clean it (page 36).

Buy a new disc.

The disc is very scratched.

Do not replay DTS CD, which is not sup-

ported by the CR-505DAB.

DTS CD is being replayed.

Load the disc with the label-side facing up

(page 20).

The disc is upside down.

The disc is dirty.

Remove the disc and clean it (page 36).

Can’t play a CD?

Remove the disc and leave the CR-505DAB

turned on for several hours until the conden-

sation has evaporated.

Condensation has formed inside the CR-

505DAB.

The CD-R/RW disc is nonstandard.

See “Disc Notes” (page 35).

It takes a long time to read It may take a longer time to read CD/MP3

This is not a malfunction.

CD/MP3.

with many track numbers.

The disc is dirty.

Remove the disc and clean it (page 36).

Buy a new disc.

It takes a long time to locate

certain tracks.

The disc is very scratched.

Does not operate during the

ACCUCLOCK function

with a message “Clock Set-

ting” displayed.

Bad receiving conditions may interfere with Press the [DISPLAY] button to disengage

the setting of the clock using ACCU-

CLOCK function.

ACCUCLOCK, and then set the clock manu-

ally.

CT (Clock Time) information has been

taken from a radio station in another time

zone.

Set ACCUCLOCK to use a speciﬁc station

(page 17).

The clock is wrong?

This is not a malfunction. The CR-505DAB

The CR-505DAB turns

itself on unexpectedly?

The ACCUCLOCK function is calibrating will turn itself off automatically when the

the clock.

ACCUCLOCK function has calibrated the

clock.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting—Continued

Trouble

Possible Cause

Remedy

Set the CR-505DAB to Standby (page 33).

The CR-505DAB must be in Standby mode,

otherwise the timed task will not work.

The CR-505DAB was already on at the

speciﬁed ON time.

You must set the recording devices to standby

mode too.

The

-connected cassette tape deck or

MD recorder had not been in standby mode.

The timer didn’t work?

The speciﬁed ON time coincided, or over- Check the timer settings and correct as neces-

lapped the ON time of another timer.

sary (page 34).

To make recordings with

recorder, connect the recorder’s analog inputs

to the CR-505DAB’s analog outputs.

-connected MD

The CR-505DAB is only connected digi-

tally to the MD recorder.

To hear what’s being recorded, press the

[MUTING] button to cancel the Mute func-

tion. Press it again to mute the CR-505DAB.

While a timed recording task is in progress,

the output of the CR-505DAB is muted.

No sound is output when a

timed playback or record-

ing task starts?

For timed playback, the volume is deter-

mined by the [VOLUME] control.

Set the volume to a suitable level (page 19).

To use

you must make an analog audio

There’s no RCA/phono analog audio con-

nection.

connection (RCA/phono) between CR-

505DAB and your Onkyo components even if

they are connected digitally.

doesn’t work.

Make sure not to short-circuit the positive and

negative speaker wires.

Standby indicator ﬂashes.

The protection circuit may be activated.

Abnormal Behavior

The CR-505DAB contains a microcomputer for signal processing and control functions. In very rare situations, severe

interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely even that this should

happen, unplug the power cord from the wall outlet, wait at least ﬁve seconds, and then plug it back in again.

Restoring the Default Settings

To reset the CR-505DAB to its factory defaults, turn it off and unplug the power cord. Then press and hold the [STANDBY/

ON] button on the CR-505DAB, and plug in the power cord.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speciﬁcations

AMP

DAB

Power Output:

20 W + 20 W (4 Ω, 1 kHz, DIN)

Tuning Frequency Range:

25 W + 25 W (4 Ω, 1 kHz, JEITA)

174.928-239.200 MHz

Dynamic power:

30 W + 30 W (4 Ω, Front)

Frequency Response: 20 Hz-20 kHz

Audio Dynamic Range:

63 dB

THD (Total Harmonic Distortion):

0.20%

THD (Total Harmonic Distortion):

0.2% (5 W Output 4 Ω)

25 (Front, 1 kHz, 8 Ω)

Input Sensitivity and Impedance:

200 mV/50 kΩ (LINE)

Output Level and Impedance:

200 mV/2.2 kΩ (REC OUT)

Frequency Response: 10 Hz-50 kHz/+3 dB, –3 dB (line)

Damping Factor:

Signal Readout:

Optical non-contact

Frequency Response: 20 Hz-20 kHz

Audio Dynamic Range:

96 dB

THD (Total Harmonic Distortion):

0.01%

Tone Control:

+9 dB, –8.2 dB, 100 Hz (BASS)

+11 dB, –9 dB, 10kHz (TREBLE)

97 dB (LINE, IHF-A)

S/N Ratio

Speaker Impedance: 4 Ω-16 Ω

Wow and Flutter:

Below threshold of measurability

Audio Output (Digital/Optical):

–22.5 dBm

Audio Output/Impedance (Analog):

Tuning Frequency Range:

87.5-108 MHz

Usable Sensitivity:

Stereo

Mono

S/N Ratio:

Stereo

1.3 V (rms) /2.2 kΩ

37.2 dBf 20.0 µV (75 Ω IHF)

17.2 dBf 2.0 µV (75 Ω)

General

Power Supply:

AC 230-240 V, 50 Hz

55 dB (IHF-A)

66 dB (IHF-A)

Power Consumption: 75 W

Stand-by Power Consumption:

1.0 W

Mono

THD (Total Harmonic Distortion):

Stereo

Mono

0.46% (1 kHz)

0.4% (1 kHz)

Dimensions (W x H x D):

205 W x 103 H x 356 D mm

Frequency Response: 30 Hz-15 kHz/+1.5 dB, –1.5 dB

Stereo Separation

Weight:

5.3 kg

37 dB (1 kHz)

Speciﬁcations and features are subject to change without

notice.

Tuning Frequency Range:

522-1611 kHz

Usable Sensitivity:

S/N Ratio:

55 dB (30 µV)

35 dB

THD (Total Harmonic Distortion):

1.60%

Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8124

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 201-785-2600 Fax: 201-785-2650 http://www.onkyousa.com

ONKYO EUROPE ELECTRONICS GmbH

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.onkyo.net

ONKYO EUROPE UK Office

Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ

UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452

HOMEPAGE

http://www.onkyo.com/

ONKYO CHINA LIMITED

Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,

N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039

D0408-2

SN 29343871A

* 2 9 3 4 3 8 7 1 A*

Download from Www.Somanuals.com. All Manuals Search And Download.

Miller Electric Welder OM 1589 User Manual
MTD Yard Vacuum 249 670A User Manual
NordicTrack Treadmill NTL198065 User Manual
Nortel Networks Cordless Telephone NN42030 300 User Manual
Nortel Networks Switch 2500 Series User Manual
Oki Network Card Telephony Adapter User Manual
Omega Automobile Parts FC 21 User Manual
Omron Blood Pressure Monitor i C10 User Manual
Oregon Scientific Clock RM836A User Manual
ParaBody Home Gym PBF405C User Manual