Omron Healthcare Blood Pressure Monitor HEM 412C User Manual

INSTRUCTION MANUAL  
MANUAL INFLATION  
BLOOD PRESSURE  
MONITOR  
Model  
HEM-412C  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
Thank you for purchasing the Omron HEM-412C Manual Inflation  
Blood Pressure Monitor. This easy-to-use monitor quickly detects  
your blood pressure and pulse measurements and displays them on  
a large, clear digital panel.  
Your new HEM-412C uses the oscillometric method of blood pressure  
measurement. This means the monitor detects your blood's movement  
through your brachial artery and converts the movements into a digital  
reading. An oscillometric monitor does not need a stethoscope so the  
monitor is simple to use. The monitor features an easy-to-squeeze inflation  
bulb that allows you to quickly fill the cuff with air. Stop pumping and the  
cuff deflates automatically. Error indicators alert you to incorrect procedures  
and an automatic power-off function conserves batteries.  
Please read this instruction manual thoroughly before using the  
Omron HEM-412C Manual Inflation Blood Pressure Monitor.  
For specific information on your own blood pressure,  
CONTACT YOUR PHYSICIAN.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
KNOW YOUR UNIT  
Systolic  
Blood Pressure Display  
Diastolic Blood Pressure  
/Pulse Display  
Arm Cuff  
Air  
Release  
Button  
On/Off  
Button  
Air Tube  
Air Inflation Bulb  
Cuff Tab  
Air  
Jack  
Air Plug  
(Connects  
to the  
air jack)  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
QUICK REFERENCE GUIDE  
1. Avoid eating, smoking, and exercising for at least 30 minutes  
before taking a measurement.  
2. Put your left arm through the cuff loop. The bottom of the cuff  
should be about 1/2'' above the elbow. The cuff tab should lie  
over the brachial artery on the inside of the arm.  
3. Pull the cuff so that it is tightened evenly around your arm.  
Press the sewn hook material firmly against the pile side of  
the cuff. Make sure that your skin will not be pinched in the  
D-ring once you inflate the cuff. Immediately deflate the cuff  
and readjust it if skin becomes pinched.  
4. Sit in a chair with your feet flat on the floor and place your left  
arm on a table so that the cuff is at the same level as your heart.  
5. After the Ready To Measure Symbol ( ) appears next to a zero  
on the digital panel, quickly squeeze the inflation bulb to inflate the  
cuff. Stop pumping when the numbers on the display are approximately  
40 mmHg higher than your normal systolic blood pressure.  
7. The cuff will deflate automatically. Remain still throughout  
the entire reading.  
8. When measurement is complete, the monitor alternately  
displays your blood pressure and pulse on the digital panel.  
9. Wait 5-10 minutes before taking another blood pressure  
measurement. You may need more rest time between  
readings depending on your individual physical characteristics.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
BATTERY INSTALLATION/REPLACEMENT  
1. Slide the battery cover off in the  
direction of the arrow.  
2. Install 4 “AA” size batteries so  
+ (positive) and – (negative)  
polarities match the polarities  
of the battery compartment as indicated.  
3. Replace the battery cover.  
4. If the Low Battery Indicator appears  
on the display, replace all four batteries.  
Long-life alkaline batteries  
are recommended.  
Low Battery Indication  
5. Remove the batteries if the monitor will  
not be used for an extended period of time.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO APPLY THE ARM CUFF  
1. Locate your brachial artery by  
pressing two fingers approximately  
one inch above the elbow crease on the  
inside of the left arm. Determine where  
your pulse is strongest.  
2. The cuff should be assembled  
correctly when it is removed from  
the box. If it is not, pass the end  
of the cuff furthest from the tubing  
through the metal D-ring to form  
a loop. The smooth cloth should  
be on the inside of the cuff loop.  
3. If the cuff is assembled correctly, the  
sewn hook material will be on the  
outside of the cuff loop and the metal  
D-ring will not touch your skin.  
4. Put your left arm through the cuff  
loop. The bottom of the cuff should  
be approximately 1/2 inch above the  
elbow. The cuff tab should lie over  
the brachial artery on the inside  
of the arm.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO APPLY THE ARM CUFF  
5. Pull the cuff so that the top and  
bottom edges are tightened evenly  
around your arm.  
6. When the cuff is positioned correctly,  
press the sewn hook material FIRMLY  
against the pile side of the cuff.  
7. Make certain the cuff fits snugly  
around your arm. The cuff should  
make good contact with your skin.  
8. Sit in a chair with your feet flat on the  
floor and place your arm on a table so  
that the cuff is at the same level  
as your heart.  
9. Relax your arm and turn your  
palm upward.  
10. Be sure there are no kinks in  
the air tubing.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO TAKE A READING  
Please read “How To Apply The Arm Cuff” before taking a reading.  
Initial LCD Test  
1. Press the On/Off button.  
SYSTOLIC mm Hg  
DIASTOLIC mm Hg  
a) All display symbols appear  
for about one second. This is the  
initial LCD Test.  
PULSE/MIN  
b) The display symbols  
Deflation Indication  
Ready To Measure  
disappear and the Deflation  
Indication Symbol (  
starts to flash.  
)
c) When the monitor completes  
the necessary preparations  
before measurement, the  
Ready To Measure Symbol  
(
) appears next to a zero.  
NOTE: Wait for the Ready To Measure  
Symbol ( ) before taking a measurement.  
2. Begin inflating the cuff by rapidly squeezing the inflation bulb  
until you have reached approximately 40 mmHg higher than  
your normal systolic reading. If your normal systolic blood  
pressure is unknown, inflate the cuff to 180 mmHg.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO TAKE A READING  
3. Stop pumping the inflation bulb when  
you have reached your correct inflation  
level and remain still. The cuff will  
begin to deflate automatically.  
Indicated Value  
Drops  
Measuring  
4. As the cuff deflates, decreasing  
numbers appear on the display.  
The Ready To Measure Symbol  
(
) flashes at the onset of  
oscillation signals.  
Blood Pressure  
Reading Display  
(for approx.  
3.5 sec.)  
Pulse Reading Display  
(for approx. 2 sec.)  
5. When measurement is complete,  
the Ready To Measure Symbol  
(
) stops flashing and your blood  
pressure and pulse display alternately.  
6. When the Deflation Indication Symbol ( ) appears on the  
display, push the air release button to release any air left in the cuff.  
NOTE: Wait 5-10 minutes before taking another blood pressure measurement.  
Waiting allows the engorged blood vessels to return to normal. You may require  
more rest time between readings depending on your individual  
physical characteristics.  
REMEMBER TO KEEP A RECORD OF YOUR BLOOD PRESSURE  
AND PULSE MEASUREMENTS.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
To protect your monitor from damage, please do the following:  
• Do not subject your monitor to extreme temperatures,  
humidity, and direct sunlight.  
• Do not fold the cuff and tubing tightly.  
• Do not inflate the monitor over 280 mmHg.  
• Do not disassemble the monitor.  
• Do not subject the monitor to strong shocks  
(for example, dropping the monitor on the floor).  
• Do not clean the monitor with volatile liquids.  
THE MONITOR SHOULD BE CLEANED WITH  
A SOFT, DRY CLOTH.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ERROR INDICATORS  
Error Symbol  
Cause  
Correction  
Cuff under-inflated.  
Wait 10 minutes before  
taking another measurement.  
Repeat steps listed under  
“How To Tke a Reading”,  
but manually inflate the  
cuff 40 mmHg higher  
than the previous  
Movement  
during measurement.  
No pulse or blood  
pressure reading due  
to very weak artery pulse.  
inflation value.  
Residual air pressure  
in cuff.  
Carefully read and repeat  
steps linsted under “How  
to Take a Reading.”  
Cuff over-inflated  
(more than 300 mmHg.)  
Replace all 4 four  
“AAA” batteries.  
Batteries have run down.  
If you continue to have difficulty obtaining a reading, call OMRON HEALTHCARE  
CUSTOMER SERVICE TOLL FREE 1-800-634-4350. Please tell the representative  
you have a Omron Model HEM-412C Manual Inflation Blood Pressure Monitor.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION INDICATORS  
NOTE:  
POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only)  
This product has been tested and found to comply with the limits for a Class B digital device,  
pursuant to part 15 of the FCC rules.  
These limits are designed to provide reasonable protection against harmful interference in  
a residential installation. The product generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instructions, may cause harmful interference  
to radio communications. However, there is no guarantee that interference will not occur  
in a particular installation. If the product does cause harmful interference to radio or television  
reception, which can be determined by turning the product on and off, the user is encouraged  
to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the product and receiver.  
Connect the product into an outlet on a circuit different from that to which  
the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for Canada only)  
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital  
apparatus as set out in the interference-causing equipment standard entitled "Digital Apparatus",  
ICES-003 of the Canadian Department of Communications.  
LICENSED UNDER U.S, PAT.  
4829419, 4942516, 4896260, 4531182, 4825364, 4686622, 4121284,  
4396976, 4371923, 4471385, 4120583, 4435732, 4672457, 4739396  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
Model:  
HEM-412C  
Display:  
LCD digital display  
Measurement Range:  
Pressure: 0-280 mmHg  
Pulse: 40-200/min.  
Accuracy/Calibration:  
Pressure: 3 mmHg or 2% of reading  
Pulse: 5% of reading  
Inflation:  
Manual by inflation bulb  
Automatic pressure release valve  
Push button valve  
Deflation:  
Rapid Air Release:  
Pressure Detection:  
Measurement Method:  
Pulse Wave Detection:  
Power Source:  
Capacitive pressure sensor  
Oscillometric method  
Capacitive pressure sensor  
4 "AA" batteries (not included)  
Battery Life:  
Approximately 1 year when used once a day  
for 2 minutes  
Operating Temperature/  
Humidity:  
50°F to 104°F (10°C to 40°C)  
30 to 85% RH maximum  
Storage Temperature/  
Humidity:  
-4°F to 140°F (-20°C to 60°C)  
10 to 95% RH maximum  
Console Weight:  
Approximately 8 oz (225g) with batteries  
Outer Dimensions:  
Approximately 4 7/8" (w) x 2 1/5'' (l)  
x 3 1/6" (h) (124mm x 56mm x 80mm)  
Cuff Dimensions:  
Approximately 5 1/2" (w) x 18 7/8" (l)  
(140mm x 480mm)  
Arm Circumference Range  
UPC Code:  
9'' to 13''  
0 73796 04122 9  
NOTE: These specifications are subject to change without notice.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED ONE YEAR WARRANTY  
Your HEM-412C Manual Inflation Blood Pressure Monitor is warranted to be free from  
manufacturing defects for a period of one year under normal use. This warranty extends  
only to the original retail purchaser.  
Should repair be needed within the warranty period, ship the unit prepaid to  
Omron Healthcare, Inc., 300 Lakeview Parkway, Vernon Hills, IL 60061,  
Attn: Service Dept., together with $5.00 for return shipping and insurance.  
Be sure to include the model number of your unit and your phone number  
on any correspondence.  
We will either repair or replace (at our option) free of charge any parts necessary  
to correct defects in the materials or workmanship.  
The above warranty is complete and exclusive. The warrantor expressly disclaims  
liability for incidental, special, or consequential damages of any nature. (Some states  
do not allow the exclusion or limitation of incidental or consequential damages,  
so the above warranty may not apply to you.)  
Any implied warranties arising by the operation of law shall be limited in duration  
to the term of this warranty. (Some states do not allow limitations on how long an  
implied warranty lasts, so the above limitation may not apply to you.)  
This warranty gives you specific legal rights and you may have other rights which  
vary from state to state. As a condition to operation of your warranty, the enclosed  
registration card must be completed and sent to us within 10 days  
from the date of purchase.  
FOR CUSTOMER SERVICE CALL TOLL FREE:  
1-800-634-4350  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For Customer Service  
Call Toll Free  
1-800-634-4350  
Manufactured for:  
OMRON HEALTHCARE, INC.  
300 Lakeview Parkway  
Vernon Hills, Illinois 60061  
Copyright © 2002 OMRON HEALTHCARE, INC.  
HEM-412CINST Rev A  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Oven H868 User Manual
Miller Electric Welding System Big Blue 600D User Manual
NETGEAR Musical Toy Instrument WAG302 User Manual
Nexus 21 Stereo Receiver Multi Control User Manual
Nikon Camera Lens ED 70180mm f 4556D User Manual
Nlynx Air Cleaner NEWPORT 9000 User Manual
Omega Thermostat DP25B TC User Manual
Omnitron Systems Technology Network Card T3 E3 User Manual
Panasonic Projector Accessories ETLAD35 User Manual
Patton electronic Network Router BODi rS BD1000 User Manual