Instruction Manual
For the digital camera
CAMEDIA C-5000 Zoom
Waterproof Case
PT-019
I Thank you for buying the Waterproof Case PT-019.
I Please read this instruction manual carefully and use the product safely
and correctly.
I Please keep this instruction manual for reference after reading it.
I Wrong use may cause damage to the camera on the inside from water
leakage, and repair may not be possible.
I Before use, perform an advance check as described in this manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Keep this product out of the reach of babies, infants, and children.
There is the possibility of occurrence of the following types of
accidents.
ț Injury by dropping onto the body from a height.
ț Injury from parts of the body getting caught in parts which open
and close.
ț Swallowing of small parts. Please consult a physician immediately
if any parts have been swallowed.
ț Triggering of the flash in front of the eyes may cause permanent
vision impairment etc.
2. Do not store with a battery in the digital camera housed in this
product. Storage with a battery inserted may lead to leakage of the
battery liquid and fire.
3. If leakage of water should occur with a camera installed in this
product, quickly remove the battery from the camera. There is the
possibility of ignition and explosion from generation of hydrogen gas.
4. This product is made of resin. There is the possibility that injuries
may be caused when it becomes broken because of strong impact
with a rock or other hard objects. Please handle with sufficient care.
5. The silica gel and the grease for silicone O-rings for this product
are not edible.
CAUTION
1. Do not disassemble or modify this product. This may cause water
leakage or trouble. In case of disassembly or modification by
persons other than those appointed by our company, the guarantee
shall not apply.
2. Do not place this product at locations with abnormally high or
abnormally low temperatures or at locations with extreme
temperature changes. The product may deteriorate.
3. Opening and closing at locations with much sand, dust, or dirt may
impair the waterproof characteristic and cause water leakage. This
should be avoided.
4. This product has been designed and manufactured for use at a
water depth within 40 m. Please note that diving to a depth in
excess of 40 m may cause permanent deformation or damage to
the Case and the camera inside the Case or may lead to water
leakage.
E-2
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Jumping into the water with the Case in your pocket or in your
hand, throwing the Case from a boat or ship into the water, and
other rough handling may cause water leakage. Please handle with
sufficient care, when handing it over from hand to hand etc.
6. If the camera on the inside should become wet because of water
leakage etc., immediately wipe off all moisture and confirm the
operation.
7. Please remove the O-ring when traveling by air. Otherwise air
pressure may make it impossible to open the Case.
8. For safe use of the digital camera in this product, please read the
"Instruction Manual" for the digital camera carefully.
9. When sealing this product, take sufficient care that no foreign
matter gets caught at the O-ring and the contact surfaces.
Batteries
G When using this product, only the LCD monitor of the camera and
not the optical viewfinder can be used. As a result, more battery
power is used than when shooting with the LCD monitor turned off.
G Please use one Olympus lithium ion rechargeable battery for
cameras (LI-10B).
G Batteries are subject to self-discharging. Therefore, always charge
up batteries fully before use.
G Take care that the battery electrodes do not become wet. This may
cause trouble or accidents.
G Carefully read the instruction manual for the camera about other
cautions regarding batteries.
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
For Prevention of Water Leakage Accidents
When water leakage occurs while this product is being used, repair of
the camera housed in this product may become impossible. Please
observe the following cautions for use.
1. When sealing this product, make sure that no hairs, fibers, sand
particles or other foreign matter stick not only to the O-ring, but
also to the contact surface (flat part of the front cover). Even a
single hair or a single grain of sand may cause water leakage.
Please check with special care.
<Examples for foreign matter sticking to the O-ring>
Hair
Fibers
Grains of sand
2. The O-ring is a consumption product. Please replace it at least
once a year by new one. Also perform maintenance for every use.
3. Deterioration of the O-ring will progress according to the use
conditions and the storage conditions. Immediately replace the O-ring
by a new one if it is damaged, shows cracks, or has lost its elasticity.
4. At the time of O-ring maintenance, clean the inside of the O-ring
groove and confirm the absence of dirt, dust, sand, and other
foreign matter.
5. Apply the specified silicone O-ring grease to the O-ring.
6. The waterproof function is not effective when the O-ring is not
installed correctly. When installing the O-ring, take care that it does
not project from the groove and that it is not twisted. Also, when
sealing the Case, close the lid after confirming that the O-ring has
not come out of the groove.
7. This product is an airtight construction made of plastic (polycarbonate).
When it is left for a long time in a car, on a boat, at the beach, or at
other places reaching a high temperature, or when it is subjected for a
long time to uneven external force, it may be deformed and the
waterproof function may be lost. Pay sufficient attention to temperature
control. Also do not place heavy objects onto the product during
storage or transport, and avoid unreasonable storage.
E-4
Download from Www.Somanuals.com. All Manuals Search And Download.
8. When the O-ring contact surface is pressed strongly from the
outside of the Case, or when the Case is twisted, the waterproof
function may be lost. Take care not to exert excessive force.
9. Please be sure to perform the advance test and the final test each
time before using the case.
10.If you should notice drops of water or other signs of water leakage
while taking pictures, immediately stop the dive, remove any water
from the camera and the product, test according to the item "Final
check", and confirm whether leakage has occurred or not.
Handling the Product
G Use or storage of the product at the following locations may cause
defective operation, defects, trouble, damage, fire, internal
clouding, or water leakage. Always avoid these locations.
ț Locations reaching high temperatures such as those under direct
sunlight, in an automobile, etc.
ț Locations with open fire
ț Water depths in excess of 40 m
ț Locations subject to vibrations
ț Locations with high temperatures and much dust or with severe
temperature changes
ț Locations with volatile substances
G This product is made of polycarbonate resin with excellent impact
resistance, but it may be damaged by scraping against rocks etc. It
also may break when it hits hard objects or is dropped.
G This product is not a case to soften impacts to the camera inside the
product. When this product with a digital camera inside it is subjected
to impacts or heavy objects are placed onto it, the digital camera may
become damaged. Please handle the product with sufficient care.
G When the product is not used for a long time, the waterproof
performance may drop because of deterioration of the O-ring etc.
Before use, always perform the advance test and the final check.
G Do not apply excessive force to the tripod socket.
G When a flash is used while the Case is being used, shadows may
appear at the edges of the picture. This is especially notable when
taking pictures in macro mode on the wide-angle side. Please use
a flash after image confirmation.
G Do not use the following chemicals for cleaning, corrosion prevention,
prevention of fogging, repair or other purposes. When these are used
for the Case directly or indirectly (with the chemicals in vaporized
state), they may cause cracking under high pressure or other
problems.
E-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Explanation
Chemicals which cannot be used
Do not clean the Case with alcohol, gasoline, thinner
or other volatile organic solvents or with chemical
detergents etc. Pure water or lukewarm water is
sufficient.
Volatile organic solvents,
chemical detergents
Do not use anticorrosion agents. The metal parts use
stainless steel or brass, and washing with pure water
is sufficient.
Anticorrosion agent
Commercial defogging
agents
Do not use commercial defogging agents. Always
use the specified desiccant silica gel.
Use only the specified silicone grease for the silicone
O-ring, as otherwise the O-ring surface may
deteriorate and water leakage may be caused.
Grease other than specified
silicone grease
Do not use adhesive for repairs or other purposes.
When repair is required, please contact a dealer or a
service station of our company.
Adhesive
G Do not perform operations other than specified in this instruction
manual, do not remove or modify parts other than specified, and do
not use parts other than specified.
Any troubles in taking pictures or with the equipment resulting from
the above actions shall be outside the guarantee.
G Our company shall be in no way responsible for accidents involving
immersion of a digital camera in water.
G Our company shall not pay any compensation for accidents (injury
or material damage) at the time of use.
G When the enclosure of the balance weight breaks, the metal on the
inside may corrode. Take care not to damage the enclosure.
G After use, wash the balance weight with pure water and wipe off all
moisture sufficiently.
E-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction …………………………………………………………E-1
Please read the following items before use ……………………E-1
For safe use…………………………………………………………E-1
Batteries ……………………………………………………………E-3
For Prevention of Water Leakage Accidents ……………………E-4
Handling the Product ………………………………………………E-5
Contents …………………………………………………………E-7-8
1. Preparations …………………………………………………E-9
Check the contents of the package.………………………………E-9
Names of the parts ……………………………………………E-10
Install the strap. …………………………………………………E-11
Master the basic operation.………………………………………E-11
Holding the Case ………………………………………………E-11
How to Press the Shutter………………………………………E-12
How to Use the Mode Dial ……………………………………E-12
How to Use the Zoom Lever …………………………………E-12
Setting the Zoom Lever ………………………………………E-13
Power Switch Operation Method ……………………………E-13
2. Advance Check of the Case …………………………E-14
Advance test before use …………………………………………E-14
Advance Test……………………………………………………E-14
3. Install the digital camera. ………………………………E-15
Check the digital camera. ………………………………………E-15
Battery Confirmation……………………………………………E-15
Confirmation of the Remaining Number of Pictures to be Taken ……E-15
Remove the hand/neck strap and lens cap from the digital camera. ……E-15
Loading in the Case ………………………………………………E-15
Which digital cameras can be loaded? ………………………E-15
Check the operation of the camera. …………………………E-15
Open the Case. ……………………………………………………E-16
Pull the mode dial of the Case. ………………………………E-16
Load the digital camera. ………………………………………E-16
Set the mode dial. ………………………………………………E-17
Insertion of silica gel ……………………………………………E-17
Check the loading status. ………………………………………E-18
Seal the Case. ……………………………………………………E-18
E-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the special balance weight. ………………………………E-18
Installation and Removal of the LCD Hood ……………………E-19
Installation ………………………………………………………E-19
Removal …………………………………………………………E-19
Mounting and Removing the Lens Cap…………………………E-20
Perform the final checks. …………………………………………E-20
Visual Inspection ………………………………………………E-20
Set the power to 'ON'. …………………………………………E-20
Try to move the mode dial. ……………………………………E-20
Final Test …………………………………………………………E-21
4. Taking Pictures Under Water …………………………E-22
How to Use the Hand Strap ……………………………………E-22
Take pictures carefully. …………………………………………E-22
Confirm the picture on the LCD monitor. ……………………E-22
Quietly press the shutter lever. ………………………………E-22
Cautions when using the flash ………………………………E-22
5. Handling After Shooting ………………………………E-23
Wipe off any waterdrop. …………………………………………E-23
Take out the digital camera. ……………………………………E-24
Wash the Case with pure water. ………………………………E-25
Dry the Case.………………………………………………………E-25
6. Maintaining the Waterproof Function ……………E-26
Remove the O-ring. ………………………………………………E-26
Remove any sand, dirt, etc. ……………………………………E-26
Install the O-ring. …………………………………………………E-27
How to Apply Grease to the O-ring ……………………………E-27
Replace consumable products. …………………………………E-28
7. Appendix………………………………………………………E-29
Q & A on the use of the PT-019 …………………………………E-29
After-sale Service …………………………………………………E-34
Specifications ……………………………………………………E-35
E-8
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Preparations
Check the contents of the package.
Check that all accessories are in the box.
Contact your dealer if accessories should be missing or damaged.
LCD hood
(on the body)
Silica gel
Silicone grease
Case body
LCD hood strap
Hand strap
Lenscap
(Check that the O-ring is normal.)
Pick for O-ring removal
Balance weight
Instruction manual
(this manual)
Guarantee card
Please read before use
Instruction Manual
For the digital camera
CAMEDIA C-5000 Zoom
Read this first about your new
OLYMPUS Waterproof Case!
Waterproof Case
!
PT-019
Authorised distributors list/
Authorised service centres list
I
I
Thank you for buying the Waterproof Case PT-019.
Please read this instruction manual carefully and use the product safely
and correctly.
Please keep this instruction manual for reference after reading it.
Wrong use may cause damage to the camera on the inside from water
leakage, and repair may not be possible.
I
I
I
Before use, perform an advance check as described in this manual.
E-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of the parts
⑥�
④�
⑦�
①�
⑧�
③�
②�
③�
①�
⑨�
⑪�
⑫�
Palm Grip
❈
LCD monitor button
OK/Menu button
Arrow Pad
AEL/Custom button
Flash mode button
Macro/Spot button
Selftimer button
Flash lever
Flash close lever
Mode dial knob
Power switch
Rear lid
Loading guide rail
LCD monitor window
Grease for silicone O-ring(white cap)
Silica gel
Balance weight
Pick for O-ring removal
LCD inner hood
LCD hood
LCD hood strap
Shade hood
Buckle opener
Lens cap
Buckle lock lever
Buckle hook
Diffuser and diffuser cover
O-ring
Shutter lever
Zoom lever
Hand strap ring
Hand strap
Tripod seat
❈
❈
❈
❈
❈
❈
❈
❈
❈
❈
❈
❈
Lens ring
Lens window
Front lid
Lens cap strap
Note ：The Case operation parts marked by * corresponds to the operation parts
of the digital camera. When the operation parts of the Case are operated,
the corresponding functions of the digital camera will operate. For details of
the functions, refer to the instruction manual for the digital camera.
E-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the strap.
Install the strap on the Case body.
Installation explanation
Hand strap
Finished installation
Hand strap ring
:
Please install the strap correctly as shown above. Our company
shall bear no responsibility for damage etc. caused by dropping
the Case because of incorrect installation of the strap.
Master the basic operation.
Please master the basic operation of the Case before taking pictures.
Holding the Case
Hold the Case securely with both hands, keep your elbows close to
your body, and hold the Case so that you can confirm the picture on the
LCD monitor of the digital camera through the LCD monitor window of
the Case.
Good example
Bad example
:
•
Do not exert excessive force onto the lens window or the lens ring.
• Take care not to put your fingers etc. over the lens window
and the flash diffuser.
Note: • Use the LCD monitor to confirm your picture. The viewfinder cannot be
used.
E-11
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Press the Shutter
When pressing the shutter lever,
press it gently, so that there will
be no movement of the camera.
Advice • If you use your index finger to operate the shutter release lever and
your middle finger for the zoom lever, you will not need to change
your finger position.
• Before activating the shutter release lever, the zoom lever should
be in the neutral (middle) position. The release cannot be activated
if the zoom lever is in the tele or wide-angle position.
• For more detailed information on operating the shutter release,
please consult the digital camera’s instruction manual.
How to Use the Mode Dial
This Case is equipped with a mode
dial knob which permits operation
of the mode dial of the loaded
digital camera from the outside.
After loading the digital camera
into the Case, seal the Case and
confirm that the mode dial can be
operated.
Advice • Please confirm that the mode dial knob has been set securely to
the mode dial of the digital camera. If the mode of the digital
camera does not change when the mode dial knob is operated,
turn the dial while pushing it lightly.
T
W
How to Use the Zoom Lever
Zoom operation is possible by
operating the zoom lever of this
Case corresponding to the zoom
lever of the digital camera in the
Case.
E-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Zoom Lever
When loading the digital camera
in the Case, fit the projecting
part of the zoom lever of the
digital camera into the recessed
part of the zoom lever on the
inside of the Case.
:
•
•
When loading the camera, confirm that the projecting
part of the zoom lever of the camera is properly set to
the recessed part of the zoom lever of the Case.
When the setting is insufficient, the loading of the
camera becomes imperfect and it may not be
possible to seal the Case or zooming may not
function. Insufficient sealing will cause water leakage.
Power Switch Operation Method
Power switch operation is
possible by operating the
power switch lever of this
Case corresponding to the
power switch lever of the
digital camera in the Case.
Note: • When the set time (initial setting: 3 minutes) passes without
any operation while the digital camera is installed in
shooting mode, the camera enters into sleep mode (standby
status) and the operation stops.
To cancel sleep mode (return to operation status), press the
shutter button or any other button.
For details, refer to the instruction manual for the digital
camera.
E-13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Advance Check of the Case
Advance test before use
This Case has been the subject of thorough quality control for the
parts during the manufacturing process and thorough function
inspections during the assembly. In addition, a water pressure test
is performed with a water pressure tester for all products to confirm
that the performance conforms to the specifications. However,
depending on the carrying and storage conditions, the maintenance
status, etc., the waterproof function may be damaged.
Before diving, always perform the following advance test and the
water leakage test after installation of the camera.
Advance Test
1. Before installing the digital camera in the Case, immerse the
empty Case to the intended water depth to confirm that there is
no water leakage.
2. Main causes of water leakage are as follows.
ț The O-ring has not been installed.
ț A part of the O-ring or the entire O-ring is outside the specified
groove.
ț O-ring damage, cracks, deterioration or deformation
ț Sand, fibers, hair or other foreign matter sticking to the O-ring,
the O-ring groove or the O-ring contact surface on the front lid
ț Damage to the O-ring groove or the O-ring contact surface on
the front lid
ț When closing the Case, check for catching of the hand strap and
silica gel after the above causes have been eliminated.
:
• The most suitable method for checking water leakage
is to immerse the Case to the intended water depth.
When this is difficult, water leakage also can be
checked at a shallow depth with no water pressure. Do
not feel that this is troublesome, but perform this test.
• If the advance test should show water leakage with
normal handling, stop using the Case and contact
your dealer or an Olympus service station (listed on
the rear page of this instruction manual).
E-14
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Install the digital camera.
Check the digital camera.
Check the digital camera before loading it in the Case.
Battery Confirmation
Since the LCD monitor is used for picture confirmation while taking
pictures under water, the battery life becomes short.
Confirm that the remaining battery capacity is sufficient.
Note:• In order to avoid losing shutter chances due to an exhausted
battery, you should always replace a battery with a fully
charged battery before each dive.
Confirmation of the Remaining Number of Pictures to be Taken
Confirm that the image storage has a sufficient remaining number
of pictures to be taken.
Remove the hand/neck strap and lens cap from the digital camera.
When a strap/lens cap is attached to the digital camera, it must be
removed to ensure proper fit.
:
•
•
When a digital camera is loaded without removing the
strap, the strap may get caught between the Case lids
and may cause water leakage.
When removing the strap, handle the digital camera with
sufficient care. Our company shall not be responsible for
damage caused by dropping the camera etc.
Loading in the Case
Which digital cameras can be loaded?
This product (PT-019) is exclusively used for the CAMEDIA C-5000
Zoom
Check the operation of the camera.
Confirm the operation according to the instruction manual for the
digital camera.
E-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Open the Case.
Insert the buckle opener of the accessory into the buckle opening
lever as shown in the figure (in direction ) Pull the buckle opener
slowly (in direction ②). When not using the buckle opener, hold the
buckle opening lever with your thumb and index finger from the side
and pull it up slowly.
①�
②�
Pull the mode dial of the Case.
Pull the mode dial of the Case until
it stops, so that it does not interfere
with the mode dial of the digital
camera.
Load the digital camera.
Quietly load the digital camera into
the Case, taking care that the
projecting part of the zoom lever of
the digital camera properly fits into
the recessed part of the zoom
lever of the Case.
:
• Confirm that the projecting part of the zoom lever of
the digital camera is set securely to the zoom lever
notch on the inside of the Case. When the setting is
not secure, the loading of the digital camera is not
complete and closing of the rear lid of the Case may
not be possible or zoom may not function even when
the zoom lever is operated.
• Insufficient sealing will cause water leakage.
E-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the mode dial.
After the digital camera has been loaded,
push down the mode dial of the Case from
the upper surface of the Case. Set it so that
the lower part of the mode dial on the inside
of the Case fits properly onto the upper part
of the mode dial of the digital camera itself.
Also, load the camera so that the power
switch of the digital camera fits into the
power switch lever notch on the inside of the
protector.
Advice
•
After setting the mode dial of the Case, set the power of the digital
camera to 'OFF', and before sealing the Case, operate the mode dial
and confirm that the mode of the digital camera is switched.
Insertion of silica gel
Before sealing the Case, insert the accessory silica gel bag (for
prevention of fogging) between the bottom of the camera and the
Case. Insert the bag with the glued longer side to the inside.
Pay attention to the orientation.
:
•
Insert the silica gel all the way at the specified location and
with the specified orientation. When the orientation is not
correct, the silica gel bag will be caught when the Case is
sealed and water leakage will be caused.
•
•
Attempting to seal the Case with the bag inserted only part of
the way will cause the silica gel bag to get caught by the O-ring
and water leakage will occur.
Once silica gel has been used, the moisture absorption
performance will be impaired. Always exchange the silica
gel when the Case is opened and closed.
E-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Check the loading status.
Always perform the following final checks before sealing the Case.
ț Has the digital camera been loaded so that the zoom lever
operates properly?
ț Has the silica gel been inserted all the way at the specified
position?
ț Has the O-ring at the Case opening part been installed properly?
ț Are the O-ring and the O-ring contact surface on the front lid free of
dirt and other foreign matter?
Seal the Case.
When the rear lid is closed
(quietly, so that the O-ring
will not come out of the
groove), the buckles are
engaged with the edge of
the rear lid, and the buckle
lock levers are pushed down
in arrow direction, the Case
will be sealed airtight.
:
•
Seal the Case by turning both buckle lock levers down in
arrow direction. When one of the buckles is left open, the
Case will not be sealed and water leakage will be caused.
Install the special balance weight.
Install the special balance weight
to the tripod mounting thread at
the bottom of the Case. Install the
balance weight securely by
tightening the accessory screw of
the balance weight.
E-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Removal of the LCD Hood
Installation
Strongly push the mounting projections of the LCD hood as shown
in the figure into the guides above and below the LCD monitor
window.
Removal
Remove the mounting projections of the LCD hood from the guides
above and below the LCD monitor window by widening the LCD
hood.
Installation
Removal
E-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting and Removing the Lens Cap
Fit the lens cap onto the lens
ring as shown in the figure. Be
sure to remove the lens cap
before shooting.
Perform the final checks.
Visual Inspection
After sealing the Case, check the sealing part of front and rear lid
visually to confirm that the O-ring is not twisted or out of the groove
and that no foreign matter has been caught.
:
•
Hairs, fibers, and other narrow items are not very apparent,
but they may cause entry of water, so that special attention
is required.
Set the power to 'ON'.
Move the power switch lever and confirm that the camera power
can be switched ON and OFF.
Try to move the mode dial.
After sealing, turn the mode dial knob and confirm that the mode
dial of the camera is switched.
:
•
•
After loading the camera into the Case, confirm that the
mode dial moves. If it does not move, there is the possibility
that oil or fat has been attached to the mode dial. Please
wipe it clean.
When no operation is performed for three minutes after the
digital camera has been loaded (or for the specified time
when a different time has been specified), the camera
enters into sleep mode (standby status) to save battery
power. It returns to operation status when the shutter button
or the zoom lever is operated.
For details, refer to the instruction manual for the digital
camera.
E-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Final Test
The final test after loading the camera is explained below. This is the only way to
eliminate worry about possible entry of water! Always perform this test. It can be
performed easily in a water tank or a bathtub. The required time is about five minutes.
Simple water
immersion test
Explanatory
image
Hints
As the Case is transparent,
waterdrops entering into it can be
confirmed easily.
Place the Case
slowly into the water.
1
2
3
4
5
6
7
8
In case of trouble with the O-ring,
three seconds are enough for water
to enter. Are there air bubbles
coming out between the lids?
Please check carefully.
At first, immerse the
Case for only three
seconds.
Remove the Case from the water and
check that no water has accumulated at
the bottom of the Case.
Check that no water
has entered into the
Case.
Is there any water trickling down?
Next, immerse the
Case for 30
seconds.
Check carefully for air bubbles!
Do not perform any operation yet,
but just observe.
Remove the Case from the water and
check that no water has accumulated
at the bottom of the Case.
Check that no water
has entered.
Perform very careful confirmation.
Check carefully for air bubbles!
Try operation of the buttons used frequently.
Check carefully for air bubbles!
If there is still no entry of water,
everything is OK!
Next, check by
immersing for three
minutes.
This is very important!
This is the final check.
Has the silica gel
become moist?
Has the silica gel become moist?
Please check carefully!
As the inside can be seen, the inspection for
entry of water also can be made securely!
Now everything is
all right.
Do not forget the
balance weight.
Now everything is all right!
Have a nice dive!
Did you remember to attach the
balance weight?
E-21
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Taking Pictures Under Water
How to Use the Hand Strap
Pass your hand through the accessory hand strap and adjust the
length with the stop button.
Take pictures carefully.
Confirm the picture on the LCD monitor.
This Case uses the LCD monitor to confirm the picture. The
viewfinder cannot be used.
Quietly press the shutter lever.
When pressing the shutter lever, hold the Case securely with both
hands and operate the lever quietly to prevent camera shake.
Cautions when using the flash
When taking macro pictures on the wide-angle side, the flash light
may be missing in some parts or the light volume may not be
uniform.
Ｗ：Approx. 0.2 m to 3.8 m
Flash working range
Ｔ：Approx. 0.3 m to 2.2 m
Depending on the conditions at the time of shooting (clarity of the
water, suspended matter, etc.), the applicable flash distance may
become shorter. After taking a picture, display it on the LCD
monitor for confirmation.
E-22
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Handling After Shooting
Wipe off any waterdrop.
After completing the shooting and
returning to land, wipe off any
waterdrop sticking to the Case.
Use air or a soft cloth not leaving
any fibers to thoroughly wipe any
waterdrop etc. from the joint
between the front and rear lid,
the shutter lever, the palm grips,
and the buckles.
:
• Especially when waterdrops remain between the front
and the rear lid, they may spill to the inside when the
Case is opened. Take special care to wipe off all
waterdrops.
• When opening the Case, take sufficient care that no
water will drop from your hair or body onto the Case
and the camera.
• Before opening the Case, make sure that your hands
or gloves are free of sand, fibers, etc.
• Do not open or close the Case at locations where
water or sand is to be sprayed. When this cannot be
avoided because you have to exchange the battery or
the image storage, place a sheet downwind from
some object and take care that no water or sand is
sprayed.
• Take care not to touch the digital camera or the
battery with hands wet with sea water.
Note:• Moisten a towel etc. in advance with pure water and keep it
in a plastic bag so that you can wipe the salt from your
hands and fingers before handling the camera.
E-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Take out the digital camera.
Open the Case carefully, pull up the mode dial from the upper surface of
the Case to disengage it from the mode lever of the camera, and then
remove the digital camera from the Case.
:
• Always place the opened Case with the O-ring side
facing up. When the Case is placed with the O-ring
side facing down, dirt or other foreign matter may be
attached to the O-ring or the O-ring contact surface
and may cause water leakage during the next dive.
• Please read the operation manual for the digital
camera for the storage of pictures etc.
• Take special care so that no water drops get onto the
camera.
E-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash the Case with pure water.
After use, seal the Case again after taking out the camera and wash it
sufficiently in pure water as soon as possible. After use in sea water,
it is effective to immerse it for a fixed time in pure water to remove
any salt.
:
• Water leakage may be caused when a high water
pressure is applied locally. Before washing the Case
with water, remove the digital camera from it.
• Operate the shutter lever and various buttons of this
product in pure water to remove salt adhering to the
shaft. Do not disassemble for cleaning.
• Drying the Case with adhering salt may impair the
function. Always wash off any salt after use.
Dry the Case.
After washing with pure water, use a soft cloth without any salt on it
and not causing any fibers to wipe off any waterdrop and dry the
Case completely at a well ventilated location in the shade.
:
• Do not use hot air from a hair drier or the like for
drying and do not expose the Case to direct sunlight,
as this may accelerate deterioration and deformation
of the Case and deterioration of the O-ring, leading to
leakage of water.
When wiping the Case, take care not to cause
scratches.
E-25
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintaining the Waterproof Function
Remove the O-ring.
Open the Case and remove the O-ring from the Case.
Removal of the O-ring
ᕃ Insert the O-ring removal pick between the O-ring and the wall of
the O-ring groove.
ᕄ Move the tip of the inserted pick under the O-ring. (Take care not
to damage the O-ring groove with the tip of the pick.)
ᕅ Hold the O-ring with your fingertips after it has come out of the
groove and remove it from the Case.
Remove any sand, dirt, etc.
After visually checking that dirt has been removed from the O-ring,
checking for attached sand and other foreign matter, as well as for
damage and cracks can be done by squeezing the entire circumference
of the O-ring lightly with your fingertips.
Use a clean cloth (that doesn't shed fibers), a toothbrush, tissue paper
or the like, to remove any foreign matter from the O-ring groove. Clean
the O-ring contact surface on the front lid in the same way to remove
any sand and dirt.
E-26
Download from Www.Somanuals.com. All Manuals Search And Download.
:
• When a mechanical pencil or a similar other sharp
object is used to remove the O-ring or to clean the
inside of the O-ring groove, the Case and the O-ring
may be damaged and water leakage may be caused.
• When the O-ring is checked with the fingertips, take
care not to stretch the O-ring.
• Never use alcohol, thinner, benzene or similar solvents
or chemicals detergents to clean the O-ring. When such
chemicals are used, it is likely that the O-ring will be
damaged or that its deterioration will be accelerated.
Install the O-ring.
Confirm that no foreign matter is attached, apply a thin coat of the
accessory grease to the O-ring, and fit the O-ring into the groove. At
this time, confirm that the O-ring does not stick out from the groove.
How to Apply Grease to the O-ring
Make sure there is no dirt on your
Apply the
specified grease
fingers or on the O-ring; then
squeeze about 5 mm of grease
onto your fingertip.
1
2
3
4
Using two fingers and
a
thumb,
Spread the grease
over the O-ring.
spread the grease over the O-ring
while rubbing it in. Use caution not to
squeeze or pull the O-ring too hard.
Once the grease has permeated
throughout the O-ring, check it for damage
or irregularities (both visually and by
touch). If you notice any abnormalities,
replace the O-ring with a new one.
Check that there
is no damage or
irregularities on
the O-ring.
Apply the grease
to the O-ring
contact surface.
Use any residual grease on your
fingertips to clean and lubricate the O-
ring contact surface on the front lid.
E-27
Download from Www.Somanuals.com. All Manuals Search And Download.
:
• Always perform maintenance of the waterproof
function even when the Case has been opened to
exchange the battery or the image storage during
shooting. Neglecting this maintenance may become
the cause of water leakage.
• When the Case is not to be used for a long time,
remove the O-ring from the groove to prevent
deformation of the O-ring, apply a thin coat of silicone
grease, and store it in a clean plastic bag or the like.
• When drying is done with salt attached, it is likely that
a function impairment will be caused. After use,
always wash off any salt.
Replace consumable products.
ț The O-ring is a consumable product. Independent of the number of
times the Case is used, it is recommended that the O-ring should
be replaced by a new one at least once a year.
ț Deterioration of the O-ring is accelerated by the use conditions and
the storage conditions. Replace the O-ring even before a year has
passed if it shows signs of damage, cracking or loss of elasticity.
Note: • Please use original Olympus products for the silicone O-ring
grease, the silica gel, and the O-ring. These consumable
products also can be purchased at an Olympus service
station.
E-28
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
Q & A on the use of the PT-019
Q1: Which digital cameras can be used?
A1 : The PT-019 is only for the models C-5000 Zoom.
Q2: What cautions must be observed when loading the digital camera into
the Case?
A2 : Pay special attention to the following items when loading the camera into
the Case.
(1) Check that the remaining capacity of the battery in the digital camera is
sufficient.
This should be checked as the LCD monitor is used under water, and the
battery consumption becomes faster.
(2) Check the remaining number of pictures on the image storage.
Please use a card with a sufficient remaining number in order to reduce
the number of times the Case has to be opened and closed.
(3) Remove the strap/lens cap from the digital camera.
When the camera is loaded without removing the strap/lens cap, the
strap/lens cap may get caught when the Case is sealed and this will
cause water leakage.
(4) Before sealing the Case, confirm that the O-ring has been installed
properly in the groove in the rear lid of the Case.
(5) Confirm that the O-ring and the O-ring contact surface on the front lid are
free of dirt, hairs, and other foreign matter.
(6) Insert the silica gel for defogging. Please use silica gel for the Olympus
Case.
(7) Finally install the special balance weight to the tripod mounting thread.
Q3: What cautions must be observed when using and storing the Case?
A3 : Pay special attention to the following items.
(1) When the O-ring contact surface is pressed strongly from the outside of
the Case, or when the Case is twisted, the waterproof function may be
impaired and water leakage may be caused.
(2) When the Case is used, left or stored at the following locations, defective
operation or trouble may be caused. Always avoid such locations.
(a) Places where the Case can reach high temperatures under direct
sunlight or in a car, places with extremely low temperatures, and
places with extreme temperature variations
(b) Places with open fire
(c) Places with volatile substances
(d) Places with vibrations
E-29
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) In case of the following handling with a camera loaded into the Case,
trouble or breakage may be caused for the Case and/or the loaded
camera. Always avoid such handling.
(a) Hitting other objects
(b) Dropping
(c) Placing heavy objects on top of the Case
(4) When the Case is not used for a long time, trouble from formation of
mold etc. may be caused. Before use, confirm the operation of all
operation parts and perform the advance test and the final test.
Q4: What cautions must be observed when opening and closing the Case?
A4 : Pay special attention to the following items.
(1) Do not open and close the Case at locations with water spray or sand
spray.
(2) Wipe off all waterdrops from the gap between the front lid and the rear lid
and around projections and recesses such as the buckles. When this is
not done, entry of waterdrops into the Case is to be feared at the time of
opening and closing.
(3) When opening the Case, take care that no water will drip from your hair
or body into the Case or onto the camera.
(4) When the Case is open, check that there is no attachment of sand, fibers
or other foreign matter to the O-ring and the O-ring contact surface on
the front lid.
(5) Do not touch the camera or the image storage with your hands to which
sea water is sticking.
(6) If you should detect waterdrops or other signs of water leakage while
shooting, immediately end the dive, perform the water leakage test
again, and confirm that there is no leakage. If the camera is wet, wipe off
any moisture and check the operation.
Q5: How should the Case be handled after use?
A5 : After use, take out the camera as soon as possible and wash the Case
with pure water. In case of use in the ocean, it is effective to immerse the
Case for a certain time in pure water to remove any salt. Operate the
buttons and levers under water to turn the shafts and wash off any salt.
After washing, use a dry cloth without any salt on it to wipe off any
moisture and dry the Case in the shade. Do not use hot air from a hair
drier or the like and do not dry the Case under direct sunlight. Exposure
to high temperatures or direct sunlight may cause deformation,
discoloration or breakage of the Case and deterioration of the O-ring.
Wipe the inside of the Case with a soft cloth not causing any fibers.
Remove the O-ring, wipe off any salt, sand, dust, etc., and also clean the
O-ring groove and the O-ring contact surface in the same way and then
E-30
Download from Www.Somanuals.com. All Manuals Search And Download.
dry them. When an object with a sharp tip is used to remove the O-ring
from the groove, the O-ring may be damaged and water leakage may be
caused. Always use the accessory pick for O-ring removal.
Q6: How should I take pictures under water?
A6 : Please observe the following items for shooting under water.
(1) Fix the Case with the accessory hand strap to your wrist.
(2) When you place a finger onto the lens window, the finger will appear in
the photo. Pay attention to the position of your fingers when holding the
Case.
(3) When pressing the shutter lever, hold the Case securely with both hands
and operate the lever quietly to prevent camera shake.
(4) Look through the LCD monitor window on the rear of the Case to confirm
the picture and then press the shutter lever. Please note that the
viewfinder cannot be used, When the LCD monitor is used, the battery is
exhausted earlier. In order to avoid losing shutter chances due to an
exhausted battery, please always replace a battery with a fully charged
battery before each dive.
Q7: How can I check for water leakage?
A7 : For confirmation, perform the advance test and the final test after loading
the camera. The advance test with immersing the Case without the
camera to the intended use depth to check for water leakage is the most
accurate test, but when this is difficult, it is safer to perform this test even
at a depth of 1 m or in a bathtub. The final test also can be performed in
a bathtub or a bucket.
Q8: What are the causes for entry of water?
A8 : The main causes for the entry of water are shown below. Please check
them most carefully.
(1) Forgetting to install the O-ring
(2) The O-ring is partly or completely outside the groove.
(3) Damage, deterioration, or deformation of the O-ring
(4) Sand, fibers, hair or other foreign matter on the O-ring
(5) Sand, fibers, hair or other foreign matter on the O-ring groove or the O-
ring contact surface
(6) Catching of the strap, the bag of silica gel, etc. at the time of sealing the
Case.
(7) Throwing the Case from a boat into the water, jumping with the Case into
the water, or other sudden application of strong forces onto the Case.
When entering the water, hand the Case over quietly or avoid impacts in
other ways.
E-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Q9: What are the important points for O-ring maintenance?
A9 : Please observe the following items.
(1) Never use alcohol, thinner, benzene or similar organic solvents or
chemical detergents to clean the O-ring. When such chemicals are used,
it is to be feared that the O-ring will be damaged or that its deterioration
will be accelerated.
(2) Use the original Olympus silicone O-ring grease (white cap). The grease
attached to Cases up to PT-008 (red cap) and the grease of other
companies are not suitable for this silicone O-ring, and use of such
grease may cause deterioration of the surface and impairment of the
waterproof function.
(3) In order to avoid deformation of the O-ring when the Case is not used for
a long time, remove the O-ring from the Case, apply a thin coat of the
special grease, and store the O-ring in a clean plastic bag. For reuse,
confirm that the O-ring is free of damage and cracks, that it has sufficient
elasticity, that the surface is free of stickiness and other abnormalities,
and use it after applying a thin coat of the special grease. Excessive
application of grease does not improve the waterproof function or the
permissible withstand pressure. However, it may facilitate attachment of
sand, dirt, etc.
A thin, uniform coat produces the best result.
(4) The O-ring is a consumable product. Replace it at least once a year.
(5) Deterioration of the O-ring is accelerated by the use conditions and the
storage conditions. Replace the O-ring immediately by a new one if it
shows signs of damage, cracking or loss of elasticity.
Q10
:
What are the important points for Case maintenance?
Please observe the following items.
A10:
(1) Never use the following chemicals for cleaning, corrosion protection,
defogging, repair or other purposes.
•
Never use alcohol, thinner, benzene or similar volatile organic solvents
or chemical detergents to clean the Case. Pure water or lukewarm water
is sufficient for cleaning.
Do not use anticorrosion agents on the metal parts. The metal parts are
made of aluminum, brass or stainless steel. Cleaning with pure water is
sufficient.
Do not use commercial defogging agents. Always use the original
Olympus defogging silica gel.
Do not use adhesive for repairs or other purposes. When repair is
required, please contact a service station of our company or your dealer.
•
•
•
E-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Q11
:
Please tell me about repairs.
A11:
Please contact a service station of our company or your dealer, if repair
should be necessary. Do not try to repair, disassemble or modify the
Case yourself. Repair, disassembly or modification by you or third
parties not authorized by Olympus invalidates the guarantee.
Q12
:
What are the model numbers of the PT-019 accessories?
The following accessories are being sold.
A12:
(1) O-ring for the PT-019 body (POL-019): This is a silicone rubber O-ring
packing to be installed in the PT-019 body to make it waterproof. O-rings
for other Case models cannot be used.
(2) Silicone O-ring grease (PSOLG-1): This is a special grease for silicone
O-ring maintenance.
(3) Silica gel (SILCA-5): This is a desiccant used to prevent fogging of the
glass parts of the Case. The quantity is five bags.
(4) LCD hood (PFUD-04): This hood is installed on the LCD monitor window
of the Case to make it easier to see the LCD monitor of the camera.
(5) Balance weight for PT-019 (PWT-019): This is a weight intended to bring
the Case close to neutral buoyancy in sea water. Under consideration of
the environment, no lead is used.
❈You can order in large computer shops and camera mass sale stores.
❈Please contact your dealer or a service station of our company when
replacement is required. Replacement will be made against payment.
E-33
Download from Www.Somanuals.com. All Manuals Search And Download.
After-sale Service
G You will receive the guarantee card from your dealer. Please make
sure that the dealer's name, the date of purchase, etc. have been
entered. If they have not been entered, immediately ask your
dealer to have them entered. Read the guarantee conditions
carefully and keep the guarantee card at a safe location.
G Please contact your dealer or one of the service stations of our
company listed in this instruction manual for questions on after-
sale service for this product or in case of defects. In case of a
defect of this product, occurring within one year after the date of
purchase and with handling according to this instruction manual,
repair based on the conditions specified in the guarantee card is
performed free of charge.
Payment is required for repairs after expiration of the guarantee
period and for trouble caused by problematic handling by the
customer even during the guarantee period.
G Our company keeps repair parts for this product for approximately
five years after the end of production of the product. Accordingly, in
principle repairs are accepted during this period. As repair may be
possible even after this period, please contact your dealer or a
service station in your neighborhood.
G Warranty is limited to and valid only in the region of intended
distribution.
G Incidental damages from defects of this product (expenses
required for diving, shooting expenses, loss of profit from photos,
etc.) shall be excluded from the guarantee. In addition, transport
expenses etc. related to repair shall be paid by the customer,
independent of whether they are incurred during or after the
guarantee period.
E-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Available models
Olympus digital camera
CAMEDIA C-5000 Zoom
Pressure
resistance
Depth of up to 40 m
Main materials
Body: Transparent polycarbonate
Buckles: Stainless steel
Grip/Shutter lever/Zoom lever/Mode dial: Red polycarbonate
Lens window: FL glass
Lens ring: Aluminum
Operation buttons: Stainless steel Nickel-plated brass
O-ring/Lens cap: Silicon rubber
LCD hood: NBR rubber
Dimensions
Weight
Width 000 mm x height 000 mm x thickness 000 mm
(projections not included)
000 g (LCD hood not included)
❈ We reserve the right to change the external appearance and the
specifications without notice.
E-35
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
|