MB260 MFP
User’s Guide
59313601
my.okidata.com
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Contents
Referring to or changing your network parameters
26
An example of how an AD-HOC network may
be set up . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installing the drivers using the Companion
Suite Pro software . . . . . . . . . . . . . . . . . 33
Checking the connection between the PC and
the multifunction machine . . . . . . . . . . . . . 36
Download from Www.Somanuals.c-om3. -All Manuals Search And Download.
MB260
Printing in duplex mode with the multifunc-
tion machine . . . . . . . . . . . . . . . . . . . . . .39
Uninstall the drivers using the Companion
Suite Pro software. . . . . . . . . . . . . . . . . .40
Download from Www.Somanuals.c-om4. -All Manuals Search And Download.
MB260
Preface
Copyright © 2009 Oki Data Americas, Inc.
Document Information
MB260 User’s Guide
P/N 59313601, Revision 1.0
May, 2009
Disclaimer
Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki
assumes no responsibility for the results of errors beyond its control. Oki also cannot guarantee that changes in
software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the
information in it. Mention of software products manufactured by other companies does not necessarily constitute
endorsement by Oki.
While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no
warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein.
The most up-to-date drivers and manuals are available from the Oki web site:
Repairs/maintenance: Repairs and maintenance should only be carried out by a
qualified technician. There are no user serviceable parts inside the machine. To
reduce the risk of electrical shock, you must not carry out these operations yourself.
Opening or removing the covers exposes you to two hazards:
- The laser beam can cause irreversible eye damage.
- Contact with electrical components can lead to electrical shock.
For installation conditions and safety precautions, refer to the separate Safety/
Installation Instructions booklet provided.
Laser Safety Information
CAUTION: Use of controls, adjustments, or performance of procedures other than those specified in this guide
may result in hazardous light exposure.
This equipment complies with international safety standards and is classified as a Class 1 Laser Product.
With specific reference to lasers, the equipment complies with laser product performance standards set by
governmental, national, and international agencies as a Class 1 Laser Product. It does not emit hazardous light,
as the beam is totally enclosed during all phases of customer operation and maintenance.
For Europe/Asia
This machine complies with IEC 60825-1:1993+A1:1997+A2:2001 standard, is classified as laser class 1 product
and is safe for office/EDP use. It contains one class 3B laser diode, 10.72 mW max, 770-795 nm and other class
1 LEDs (280 µW at 639 nm).
Direct (or indirect reflected ) eye contact with the laser beam might cause serious eye damage. Safety precautions
and interlock mechanisms have been designed to prevent any possible laser beam exposure to the operator.
For North America
CDRH Regulations.
This equipment complies with the FDA performance standards for laser products except for deviations pursuant
to Laser Notice No.50, dated 24 June 2007 and contains 1 class 3B laser diode, 10.72 milliwatt, 770-795
nanometer wavelength and other class 1 LEDs (280 µW at 639 nm).
This equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes of
operation and maintenance.
Download from Www.Somanuals.c-om5. -All Manuals Search And Download.
MB260
Positions of Safety labels on the machine
The device has warning labels at the positions shown below. For your safety, you must never touch these surfaces
when you remove a paper jam or when you replace the Toner cartridge.
Symbols for the main power switch
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
-
-
means POWER ON.
means POWER OFF.
guarantee is valid for ninety (90) days from the delivery date, the copy of the receipt being the proof of purchase. In
case of a CD-ROM fault that due to accident or misuse, the CD-ROM will not be replaced as per the warranty.
Responsibility
If the CD-ROM is not working properly, send it to the retailer together with a copy of the receipt. It is the retailer's sole
responsibility to replace the CD-ROM. Nobody, not even the manufacturer who is involved in the creation, realization,
merchantability and delivery of this program would be responsible for direct, indirect or immaterial damages, such as,
but not limited to, loss of information, loss of time, execution loss, loss of revenue, loss of customers, due to the use or
Download from Www.Somanuals.c-om6. -All Manuals Search And Download.
MB260
Trademarks
PCL® is a registered trademark of the Hewlett-Packard Company.
PostScript® is a registered trademark of Adobe Systems Incorporated.
Adobe® and the Adobe® products referred to here are registered trademarks of Adobe Systems Incorporated.
PaperPort11SE is a registered trademark of ScanSoft.
Microsoft® Windows 2000®, Microsoft® Windows Server 2003®, Microsoft® Windows XP®, Microsoft® Windows
Vista® and any other Microsoft® product referred to here are registered trademarks of Microsoft Corporation registered
and/or used in the United States and/or in other countries.
All the other brands or products referred to as examples or in order to give additional information are registered
trademarks of their respective owners.
The informations contents of this user manual are subject to change without notice.
Prohibited reproductions
Do not copy or print any item for which reproduction is prohibited by law.
Copying or printing the following items is generally prohibited by local law:
- bank notes;
- checks;
- bonds;
- stock certificates;
- bank drafts;
- passports;
- driver's licenses.
The preceding list is meant as a guide only and is not inclusive. If you have any questions concerning the legality of
copying or printing certain items, consult with your legal advisor.
Download from Www.Somanuals.c-om7. -All Manuals Search And Download.
MB260
Installation
Location conditions
By choosing an appropriate location, you preserve the longevity of the machine. Check that the selected location has
the following characteristics:
- Choose a well ventilated location.
- Make sure not to obstruct the ventilation grids located on the left and right sides of the device. During the
installation, make sure to place the machine thirty centimeters away from the surrounding objects so all the lids
can be easily opened.
- Make sure that this location does not present any ammonia nor any other organic gasses emission hazard.
- The ground outlet (refer to the security notices presented in the Safety booklet ) to which you plan to connect the
machine must be located close to this one and have an easy access.
- Make sure that the machine is not directly exposed to sun light.
- Make sure not to place the machine in an area exposed to an air flow generated by an air conditioning, heating or
ventilation system, nor in an area subject to large temperature or humidity variations.
- Choose a solid and horizontal surface on which the machine will not be exposed to intense vibrations.
- Keep the machine away from any object that could obstruct its ventilation ports.
- Do not place the machine close to hangings or any other flammable objects.
- Choose a location where splashes of the water and other liquids are limited.
- Make sure that this location is dry, clean and dust free.
Cautions of use
Take into account the important precautions below when using the machine.
Running environment:
- Temperature: 10 °C to 27 °C [50 °F to 80.6 °F] with an ambient humidity included between 15 to 80% (up to 32°C
[89.6 °F] with an ambient humidity included between 15 to 54%).
Terminal:
The section below describes the precautions to be taken when using the machine:
- Never turn the machine off and never open the lids while printing.
- Never use gas or flammable liquids, or objects generating magnetic field close to the machine.
- When you unplug the power cord, always hold the connector without pulling the cord. A damaged cord presents
a potential fire hazard or an electric shock hazard.
- Never touch the power cord with wet hands. You risk getting an electric shock.
- Always unplug the power cord before moving the machine. Otherwise, you could risk having the cord damaged
and create a fire hazard or an electric shock hazard.
- Always unplug the power cord when you plan not to use the machine for a long period of time.
- Never put objects on the power cord, never pull it and never fold it. This could cause a fire hazard or an electric
shock hazard.
- Always make sure that the machine is not sitting on the power cord or any other electric device communication
cables. Make sure also that neither cord nor cable is introduced to the machine inner mechanism. This would
expose you to a machine malfunction risk or to a fire hazard.
- Make sure that the printer is unplugged from the power outlet before connecting or disconnecting an interface
cable to the printer (use a shielded interface cable).
- Never try to remove any fixed pane or hood. The machine contains high voltage circuits. Any contact with these
circuits can cause an electric shock risk.
- Never try to modify the machine. This could cause a fire hazard or an electric shock hazard.
- Always make sure that paper clips, staples or other small metallic items do not get inside the machine via the
ventilation ports or other ports. Such items create fire hazards or electric shock hazards.
- Prevent water and any other liquid from spilling on the machine or near to it. Any contact of the machine with water
or liquid can cause a fire hazard or an electric shock hazard.
Download from Www.Somanuals.c-om8. -All Manuals Search And Download.
MB260
- If liquid or metallic item gets accidentally inside the machine, turn it off immediately, unplug the power cord and
contact your retailer. Otherwise, you will face a fire hazard or an electric shock hazard.
- In case of heat, smoke, unusual smell or abnormal noise emissions, turn the machine off, unplug the power cord
immediately and contact your retailer. Otherwise, you will face a fire hazard or an electric shock hazard.
- Avoid using the machine during an "electric storm", this can cause an electric shock hazard due to lightning.
- Never move the terminal during printing.
- Always lift the terminal when you wish to move it.
Make sure to place the machine in well ventilated premises. When in operation, the printer generates
a small amount of ozone. An unpleasant smell can come from the printer if it is used intensively in
poorly ventilated premises. For a secure use, make sure you place the machine in well ventilated
premises.
Safety information
When using your product, the following safety precautions should always be followed.
Safety During Operation
In this information slip, the following symbols are used:
Indicates a potentially hazardous situation which, if instructions are not followed, could
WARNING:
CAUTION:
result in death or serious injury.
Indicates a potentially hazardous situation which, if instructions are not followed, may result in
minor or moderate injury or damage to property.
WARNING
- Connect the power cord directly into a wall outlet and never use an extension cord.
- Disconnect the power plug (by pulling the plug, not the cable) if the power cable or plug becomes frayed or
otherwise damaged.
- To avoid hazardous electric shock or laser radiation exposure, do not remove any covers or screws other than
those specified in the Operating instructions.
- Turn off the power and disconnect the power plug (by pulling the plug, not the cable) if any of the following
conditions exists:
•
•
•
You spill something into the product.
You suspect that your product needs service or repair.
Your product’s cover has been damaged.
- Do not incinerate spilled toner or used toner. Toner dust might ignite when exposed to an open flame.
- Disposal can take place at our authorised dealer or at appropriate collection sites.
- Dispose of the used toner cartridge (or bottle) in accordance with the local regulation.
CAUTION
- Protect the product from dampness or wet weather, such as rain, snow, and so on.
- Unplug the power cord from the wall outlet before you move the product. While moving the product, you should
take care that the power cord will not be damaged under the product.
- When you disconnect the power plug from the wall outlet, always pull the plug (not the cable).
- Do not allow paper clips, staples, or other small metallic objects to fall inside the product.
- Keep toner (used or unused), toner cartridge (or bottle), ink (used or unused) or ink cartridge out of reach of
children.
Download from Www.Somanuals.c-om9. -All Manuals Search And Download.
MB260
- Be careful not to cut yourself on any sharp edges when you reach inside the product to remove misfed sheets of
paper or masters.
- For environmental reasons, do not dispose of the product or expended supply wastes at household waste
collection point. Disposal can take place at our authorised dealer or at appropriate collection sites.
- Our products are engineered to meet the high standards of quality and functionality, and we recommend that you
only use the expendable supplies available at an authorised dealer.
Power Supply
The socket-outlet shall be installed near the product and shall be easily accessible.
Paper recommendations
Loading paper in the main unit tray
•
Insert paper with the face down, and adjust paper guides to the paper format to avoid feed failure, skewing, and
paper jams.
•
Amount of loaded paper must not exceed the loading mark. If the loading mark is exceeded, this may cause feed
failure, skewing, and paper jams.
•
•
•
Adding paper in the pile must be avoided because it may cause double feeding.
When withdrawing the cassette from the main unit, always support it with both hands to avoid dropping it.
If you use paper already printed by your machine or another printer, the printing quality may not be optimal.
Handling of paper
•
•
•
Curling must be corrected before printing.
Curls must not exceed 10 mm.
Care must be taken with storage to prevent feed faults and image defects due to leaving the paper in conditions of
high humidity.
Humidity control
•
•
•
Paper which has become damp, or paper which has been left unused for a very long time, must not be used.
After opening the paper, it must be kept in a plastic bag.
Paper with waved ends, paper which is creased, paper with crumples, and any other non-normal paper must not
be used.
Handling the unit
Operator shocks
During printing, shocks must not be applied to the paper feed cassette, tray, cover, and other parts of the machine.
Moving the unit
When moving the unit on a desk, it must be lifted, and not dragged.
Handling the Toner Cartridge
•
•
Must not be stood on the side, or held upside down.
Must not be shaken strongly.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Rules for use symbols
WARNING
Indicates important safety notes.
Ignoring these notes could result in serious injury or death. Be sure to read these notes. Refer to the security notices
presented in the Safety booklet.
CAUTION
Indicates important safety notes.
Ignoring these notes could result in moderate or minor injury, or damage to the machine or to property. Be sure to read
these notes. Refer to the security notices presented in the Safety booklet.
Important
Indicates points to pay attention to when using the machine, and explanations of likely causes of paper misfeeds,
damage to originals, or loss of data. Be sure to read these explanations.
Note
Indicates supplementary explanations of the machine’s functions, and instructions on resolving user errors.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Terminal description
Front and Back sides
1. Control panel
8. Manual input tray
2. Paper jam cover
9. Paper tray
3. Power supply cord connection
4. On/Off switch
10. Cartridge access cover
11. Fold-down stopper for paper delivery
12. Paper output
5. Slave USB connection (for PC)
6. Master USB connection (USB key)
7. Manual paper feed setup guides
13. Smart card insertion point
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Command panel
1. Screen.
11. Key
12. Key
: stops the current operation.
2. Digital keypad.
: sets up the activation delay and toner save in
3. Key
: document analysis to the PC or a media
copy mode.
(USB key).
13. Key
: access to print menu (print functions list,
4. Key
5. Key
6. Key
: local copy.
machine settings, etc.).
: stops the current PC print job.
: Validation.
14. Key
15. Key
: analysis resolution setup.
: contrast setup.
7. Key OK: confirms the displayed selection.
16. Icon
17. Icon
18. Icon
19. Icon
: resolution "Quality Text".
: resolution "Photo".
: resolution "Text".
: color mode.
8. Key
9. Key
10. Key
!
: menu access and navigation down the menus.
: back to the previous menu and input correction.
: navigation up the menus.
C
"
Accessing terminal menus
All terminal functions and settings are available via the menu and are associated to a specific menu command.
For example, the menu command 51 launches the printing of the functions list (the functions list stores the list of all
terminal menus, sub-menus and their identification number).
Two methods are available to access menu items: the step by step method or the shortcut method.
To print the functions list with the Step by step method:
1 Press !.
2 Use the ! or " button to browse the menu and select 5 - PRINT. Confirm with OK.
3 Use the ! or " button to browse the menu PRINT and select 51-FUNCTIONS LIST. Confirm with OK.
To print the functions list with the shortcut method:
1 Press !.
2 Enter 51 with the numerical keypad to directly print the functions list.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Packaging contents
Device installation
The packaging contains the items listed below:
1 Unpack the device.
2 Install the device respecting the security notices
Multifunction device
stated at the beginning of this booklet.
3 Remove all stickers from the machine.
4 Remove the plastic protection film from the screen.
Feed cassette paper insertion
Before inserting paper, refer to the
Important
Your device accepts a number of formats and types of
You can use paper weighing
Important
between 60 and 105 g/m2.
1 toner cartridge
1 Remove the paper feed cassette completely.
1 Installation guide
1 PC installation CD ROM and 1 OCR PC software CD
ROM (depending on model)
2 Push the lower panel down until it clicks.
2 booklets (safety and warranty)
1 power cord
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
3 Setup the back side feed cassette stop by pushing
the "PUSH" lever (A).
assure the maximum copies per cartridge.
Hold it by its handle.
Then adjust the lateral paper guides to the paper
format by pushing lever (B) located on the left
guide. Adjust the length paper guide to the paper
format by pushing lever (C).
4 Insert the cartridge in its slot by pushing it until it
clicks (last move down) as shown on the picture
below.
4 Take a paper stack, pull the paper off and align it
on a flat surface.
5 Put the paper stack in the feed cassette
(200 sheets of 80 g/m² paper for instance).
6 Put the feed cassette back in its location.
5 Close the cover.
Cartridge installation
Paper delivery stop
1 Stand in front of the machine.
Adjust the paper delivery stop, depending on the format of
the document to be printed. Do not forget to raise the flap
to prevent the sheets from falling down.
2 Push the left and right sides of the cover and pull it
towards you at the same time.
3 Unpack the new cartridge. Gently roll the cartridge
5 or 6 times to distribute the toner evenly inside the
cartridge. Thoroughly rolling the cartridge will
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
1 Select the desired language using the " or !
Starting your device
Device connection
buttons and confirm with OK.
The setup is now complete and the functions list is
automatically printed out.
Before plugging the power cord, it
is imperative to refer to the Safety
booklet.
The LCD screen displays the message PAPER EMPTY if no
paper has been loaded in the paper tray (see Loading
been loaded, printing will resume.
WARNING
1 Make sure that the On/Off switch is on Off
(O position).
Paper insertion in the manual input
tray
2 Connect the power cord to the device.
Plug the power cord to outlet on the wall.
Before inserting paper, refer to the
Important
The manual input tray allows you to use various paper
formats with greater grammage than the one used in the
paper feed cassette (refer to the paragraph
Only one sheet or envelope can be fed at a time.
You can use paper weighing
Important
between 52 and 160 g/m².
1 Spread the manual feed guides to the maximum.
The power cord is used as a power
unit cut off. As a precaution, the
outlet shall be located close to the
device and be of easy access in
case of danger.
WARNING
3 Press the On/Off button to turn on the device
(I position).
Device initial setup
After a few seconds, when the machine has warmed up,
the Easy Install function is launched and the LCD screen
displays the following message:
2 Insert a sheet or an envelope in the manual input
tray.
3 Adjust the paper guides against the right and left
edges of the sheet or the envelope.
1 - FRANCAIS
2 - ENGLISH
4 Print making sure that the chosen paper format
corresponds to the selected format on the printer
The Easy Install function will help you configure your
machine by guiding you through the basic settings.
Use of envelopes
If you wish to modify the setting displayed, press the OK
button. If you do not want to modify the displayed setting,
press the C button: the Easy Install function then
displays the next basic setting.
•
•
Feeding can be done only through the manual feed.
Recommended area should be the area which
excludes 15 mm from the leading edge, 10 mm from
both the left and right edges, and the rear edge.
•
•
A few lines may be given in solid print at the part of
being overlapped.
If you do not want to carry out the
initial setup, press the
button. A
Envelopes which are not recommended may lead to
improper printing (refer to the paragraph
confirmation message appears. Press
Note
the button again to confirm.
To manually modify and customise the
machine settings, refer to
•
•
Curled envelope after printing should be fixed
manually.
Small crumples on the edge of the wide side of
envelopes, smearing, or less clear printing may
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
appear on the reverse side.
•
•
•
Set envelope by pressing the folding line of four edges
properly after releasing air inside.
Set envelope in a proper position after aligning in case
it is bent or warped.
Paper conditioning is not allowed. And it should be
used under normal office environment.
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
5 Choose with the buttons " or ! the printing option
(see examples below) depending on the copy
mode that you want: 1 Page to 1, 1 Page to 4 or
1 page to 9.
Copy
Your machine has the function to make one or more
copies.
You can also set up several parameters in order to make
copies at your will.
Simple copy
In this case, the default parameters are applied.
1 Place the document to be copied face down on the
glass, respecting the indications around the glass.
2 Press the
button twice. The copy is made
using the default parameters.
ECO mode copy
The ECO mode enables you to reduce the amount of
toner consumed on the page so as to save your printing
costs.
When the ECO mode is used, the toner consumption is
reduced and the print density becomes lighter.
Confirm with the OK button.
1 Place the document to be copied face down on the
6 Adjust the desired zoom level, from 25% TO 400%
with the buttons " or !, confirm with the OK
button (only available in 1 Page to 1 copy mode).
glass, respecting the indications around the glass.
2 Press the
button.
button.
7 Adjust the desired origin values with the digital
keyboard buttons " or ! then confirm with the OK
button.
3 Press the
8 Choose the resolution depending on the printing
quality that you want AUTO, TEXT, QUALITY
TEXT or PHOTO with the buttons " or !, then
confirm with the OK button.
Advanced copying
The sophisticated copy allows to do custom setups for the
current copy.
9 Adjust the contrast level with the buttons " or !,
You can start copy by pressing the
then confirm with the OK button.
10 Adjust the desired brightness level with the buttons
Note
button at any time in below
steps.
" or !, then confirm with the OK button.
11 Choose the paper type NORMAL, THICK with the
buttons " or !, then confirm with the OK button.
1 Place the document to be copied face down on the
glass, respecting the indications around the glass.
ID Card Copy mode
After step 1, you can directly enter the
The ID CARD copy function is used for copying both sides
of an identity card or driver’s license type document on an
A4 format sheet (original document size < A5) or on a
Letter format sheet (original document size < Statement).
number of copies with the numerical
keypad and press the OK button to
validate. Then refer to step 4.
Note
2 Press the
button.
The LCD screen displays useful operating instructions
(when the original document should be placed, when the
document should be turned over, etc.) and asks for your
confirmation to proceed with the operation.
3 Enter the number of copies that you want and
confirm with the OK button.
4 Choose the paper tray AUTOMATIC or MANUAL
with the buttons " or !, then confirm with the OK
button.
Zoom and Origin adjustments are
Important
not available in this copy mode.
1 Press the
button.
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
2 Enter the desired number of copies and confirm
Special setup for the copying
with the OK button.
Setups done through this menu become the device
default setups after you confirm.
3 Choose the paper tray AUTOMATIC or MANUAL
with the buttons " or !, then confirm with the OK
button.
When the quality of the printing is
not satisfying, you can proceed to a
calibration (see Calibrate your
Copying in ID Card mode is only
possible on A4 (original document
size < A5) or Letter (original
document size < Statement) paper
size. Make sure that the selected
paper tray uses the correct paper
size.
Important
Important
Resolution setup
The RESOLUTION parameter allows you to setup the
photocopy resolution.
4 Choose the copying option ID CARD with the
buttons " or ! and confirm with the OK button.
! 841 - ADVANCED FCT/COPY/RESOLUTION
5 Choose the resolution depending on the desired
printing quality AUTO, TEXT, QUALITY TEXT or
PHOTO with the buttons " or !, then confirm with
the OK button. For optimal results with ID
documents, select the PHOTO resolution.
1 Press !, enter 841 using the keypad.
2 Choose the resolution with the buttons " or !
according to the following table:
6 Adjust the contrast level with the buttons " or !,
Parameter
Signification
Low resolution.
Icon
then confirm with the OK button.
7 Adjust the desired brightness level with the buttons
AUTO
none
" or !, then confirm with the OK button.
Standard resolution for
documents containing text and
graphics.
8 Choose the paper type NORMAL, THICK with the
buttons " or !, then confirm with the OK button.
The LCD screen displays the following message:
TEXT
QUALITY Optimal resolution for
PUT ID CARD
THEN OK
TEXT
documents containing text.
Optimal resolution for
documents containing
photographies.
9 Place your identity card or any other official
document against the glass of the flatbed scanner,
as shown below:
PHOTO
3 Confirm your choice by pressing the OK button.
4 Quit this menu by pressing the button.
You can also change the resolution by
pressing the button.
Note
Zoom setup
The ZOOM parameter allows you to reduce or enlarge an
area of a document by choosing the origin and the zoom
level to apply to the document, from 25 to 400 %.
10 Press the OK button.
The document is scanned then the LCD screen
displays the following message:
! 842 - ADVANCED FCT/COPY/ZOOMING
TURN UP DOC
THEN OK
1 Press !, enter 842 using the keypad.
2 Enter the desired zoom level with the
alphanumerical keypad or choose among
predefined values with the buttons " and !.
11 Turn your document over then confirm with the
OK button.
3 Confirm your choice by pressing the OK button.
The machine prints out a copy of your document.
4 Quit this menu by pressing the
button.
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Analysis origin setup
Paper tray selection
If you want, you can change the origin of the scanner.
The Automatic selection can have two meanings
depending on the paper format defined on the paper
trays. The following table describes the different cases.
By entering new values for X and Y in mm (X < 209 and
Y < 280), you move the analysed area as shown on the
diagram below.
Default tray
Tray used for copy
Selection between the
AUTOMATIC main tray and the
Same paper
format in the
trays
manual tray.
The manual tray is
used.
MANUAL
AUTOMATIC The main tray is used.
Different
! 843 - ADVANCED FCT/COPY/ORIGIN
paper format
in the trays
The manual tray is
used.
MANUAL
1 Press !, enter 843 using the keypad.
2 Select the X and Y coordinates with the buttons "
or !.
! 852 - ADVANCED FCT/SCAN. & PRINT/TRAY
3 Setup the desired coordinates with the numerical
PAPER
keypad or the buttons " and !.
1 Press !, enter 852 using the keypad.
4 Confirm your choice by pressing the OK button.
2 Select the default paper tray to use, AUTOMATIC
5 Quit this menu by pressing the
button.
or MANUAL, with the buttons " and !.
3 Confirm by pressing the OK button.
Contrast setup
4 Quit this menu by pressing the
button.
The CONTRAST parameter allows to choose the
photocopy contrast.
Flat-bed analysis margins setup
If you want to, you can offset the lateral margins of the
document to the left or right during the analysis with your
flat-bed scanner.
! 844 - ADVANCED FCT/COPY/CONTRAST
1 Press !, enter 844 using the keypad.
2 Setup the desired level of contrast with the buttons
! 854 - ADVANCED FCT/SCAN. & PRINT/
" and !.
FLATBED MARG
3 Confirm your choice by pressing the OK button.
1 Press !, enter 854 using the keypad.
4 Quit this menu by pressing the
button.
2 Setup the left / right margins offsets (by 0.5 mm
steps) with the buttons " and !.
3 Confirm by pressing the OK button.
Brightness setup
4 Quit this menu by pressing the
button.
The BRIGHTNESS parameter allows to lighten or darken
your output.
Left and right printing margins setup
! 845 - ADVANCED FCT/COPY/BRIGHTNESS
If you want to, you can offset the lateral margins of the
document to the left or right during printing.
1 Press !, enter 845 using the keypad.
2 Setup the desired brightness with the buttons "
and !.
! 855 - ADVANCED FCT/SCAN. & PRINT/
3 Confirm your choice by pressing the OK button.
PRINTER MARG
4 Quit this menu by pressing the
button.
1 Press !, enter 855 using the keypad.
2 Setup the left / right margins offsets (by 0.5 mm
Paper type setup
steps) with the buttons " and !.
3 Confirm by pressing the OK button.
! 851 - ADVANCED FCT/SCAN. & PRINT/PAPER
TYPE
4 Quit this menu by pressing the
button.
1 Press !, enter 851 using the keypad.
2 Select the paper NORMAL or THICK that you use
with the buttons " and !.
3 Confirm your choice by pressing the OK button.
4 Quit this menu by pressing the
button.
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Top and bottom printing margins setup
If you want to, you can offset the lateral margins of the
document towards the top or the bottom during printing.
! 856 - ADVANCED FCT/SCAN. & PRINT/TOP
PRINT.
1 Press !, enter 856 using the keypad.
2 Setup the top / bottom margins offsets (by 0.5 mm
steps) with the buttons " and !.
3 Confirm by pressing the OK button.
4 Quit this menu by pressing the
button.
Format paper setup
This menu allows you to define the default paper format
of the manual tray and the main tray. You can also setup
the default scanning width.
! 857 - ADVANCED FCT/SCAN. & PRINT/
PAPER FORMAT
1 Press !, enter 857 using the keypad.
2 Select the paper tray for which you want to define
a default paper format with the buttons " and !.
3 Confirm by pressing the OK button.
4 Choose the paper format with the buttons " or !
according to the following table:
Paper tray
Available paper format
MAN. TRAY A5, Statement, A4, Legal and Letter
AUTO. TRAY A5, Statement, A4, Legal and Letter
SCANNER
LTR/LGL and A4
5 Confirm by pressing the OK button.
6 Quit this menu by pressing the
button.
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Parameter
Signification
Parameters/
Setup
91 - Printer error
timeout
Time-out before document being
printed is deleted following a print
error in PC print mode.
92 - Printer wait
timeout
You can setup your machine as you like depending on the
use. You will find in this chapter description of the
functions.
Wait time-out for data from PC
before the task is deleted in PC
print.
93 - Replace format
Page format change. This
parameter allows you to print a
LETTER format document on A4
pages using the LETTER/A4
setting.
You can print the functions guide and the available setup
of your multifunction machine.
Language
This setting enables you to choose the menu language of
your choice. By default, the multifunction machine is set
to English.
96 - NBR. WEP
Keys
Number of WEP keys allowed
(from 1 to 4).
Printing the functions guide
To select the language:
!203 - SETUP / GEOGRAPHICAL / LANGUAGE
The printing is not possible on A5
(or Statement) paper format.
Important
1 Press !, enter 203 using the keypad.
!51 - PRINT / FUNCTIONS LIST
2 Select the required language using ! and ", then
press the OK key to confirm.
Press !, enter 51 using the keypad.
3 To exit this menu, press
.
The printing of the functions guide starts.
Technical Parameters
You can also access the PRINT menu
by pressing the button.
Note
As delivered your machine is preset by default. However,
you may adjust it to meet your requirements by resetting
the technical parameters.
Print the list of setups
To set the technical parameters:
The printing is not possible on A5
(or Statement) paper format.
!29 - SETUP / TECHNICALS
Important
1 Press !, enter 29 using the keypad.
To print the list of setups:
2 Select the desired parameter and confirm with OK.
!56 - PRINT / SETUP
3 With the keys ! or ", modify the parameter
settings by following the table below and press OK.
Press !, enter 56 using the keypad.
Parameter
Signification
The printing of the list of setups starts.
8 - Eco energy
Choosing the printer standby
delay: the printer will switch to
standby after a delay (in minutes)
of NON-operation or during the
period of time of your choice.
You can also access the PRINT menu
by pressing the button.
Note
Lock the machine
Note: you can also access this
parameter by pressing the
This function prevents non-authorized people from
accessing the machine. An access code will be required
every time someone wants to use the device. After each
use, the device will lock automatically.
key from the idle screen.
80 - Toner save
90 - RAW Port
Makes printing lighter to save toner
cartridge ink.
Before that you have to enter a lock code.
RAW network print port
connection.
!811 - ADVANCED FCT / LOCK / LOCKING CODE
1 Press !, enter 811 using the keypad.
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
2 Enter your lock code (4 digits) with the keyboard,
Printed pages counter
confirm with OK.
To view the number of pages printed on your machine:
If a code is already registered, enter
Important the old code before typing the new
one.
!824 - ADVANCED FCT / COUNTERS / PRINTED PG
1 Press !, enter 824 using the keypad.
3 Enter again your lock code (4 digits) with the
2 The number of printed pages appears on the
keyboard, confirm with OK.
screen.
4 Quit this menu by pressing the
button.
3 Quit this menu by pressing the
button.
Lock the keyboard
Display the consumables status
Every time you use your machine, you will have to enter
your code.
You can read at any time the remaining toner in the
cartridge. This level appears in percentage.
!812 - ADVANCED FCT / LOCK / LOCK KEYBD.
!86 - ADVANCED FCT / CONSUMABLES
1 Press !, enter 812 using the keypad.
2 Enter the four-digit locking code with the keypad.
3 Press OK to confirm.
1 Press !, enter 86 using the keypad.
2 The available toner percentage appears on the
screen.
4 With the buttons ! or ", choose ON and confirm
3 Quit this menu by pressing the
button.
with OK.
5 Quit this menu by pressing the
button.
Calibrate your scanner
Lock the Media service
You can do this operation when the quality of photocopied
documents is not satisfactory anymore.
This function prevents access to the Media service. The
access code will be required every time someone wants
to use the USB key functions:
!80 - ADVANCED FCT / CALIBRATION
•
•
analyse the contents of a connected USB key,
print from a USB key, delete files.
1 Press !, enter 80 using the keypad. Confirm
with OK.
To access the Media service locking menu:
2 The scanner is triggered and a calibration is done
automatically.
!816 - ADVANCED FCT / LOCK / LOCK MEDIA
3 At the end of the calibration, the machine comes
back to the screen saver.
1 Press !, enter 816 using the keypad.
2 Enter the four-digit locking code with the keypad.
3 Press OK to confirm.
4 With the buttons ! or ", choose ON and confirm
with OK.
5 Quit this menu by pressing the
button.
Read the counters
This function allows you to view the activity counters for
your machine at any time.
According to your needs, you can read the counters for:
•
•
scanned pages,
printed pages.
Scanned pages counter
To view the number of pages scanned on your machine:
!823 - ADVANCED FCT / COUNTERS / SCANNED
PAGE
1 Press !, enter 823 using the keypad.
2 The number of scanned pages appears on the
screen.
3 Quit this menu by pressing the
button.
- 23 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Radio ad-hoc network
Network features
In an ad-hoc network, the devices communicate directly
with each other without passing through an access point.
The speed of communication across the whole radio
network is as fast as the weakest connection in the
network. The speed of communication is also dependent
on spatial distance between transmitter and receiver, as
well as the number of barriers, such as walls or ceilings.
You may connect your multifunction terminal to a wireless
network.
However, practical knowledge of your computer
configuration is required to set up a network.
You can connect your machine to a PC using a USB cable
or make a wireless connection (via radio) with a PC or
network.
Please note that in ad-hoc mode,
the WPA/WPA2 encryption method
is not available.
Important
If you have a WLAN adaptor, you
can incorporate your machine as a
network printer into a radio network.
This works only with an approved
adaptor that you can obtain from our
Important
ordering department. For further
information, contact
Type of radio network
A radio network or WLAN (Wireless Local Area Network)
is created when at least two computers, printers or other
peripheral devices communicate with each other in a
network via radio waves (high frequency waves). The
transmission of data in the radio network is based on the
standards 802.11b and 802.11g. According to how the
network is set up, it may be described as an infrastructure
network or an ad-hoc network.
Radio networks (WLAN)
Three steps are necessary to incorporate your machine
into a radio network (WLAN):
Beware, when you are using a
wireless connection, that certain
items of medical equipment,
1 Configure the network to your PC.
2 Set up the parameters for your machine so that it
sensitive or security systems may
be affected by the radio
can function in a network.
CAUTION
3 Having set up the parameters for your device,
install the Companion Suite Pro software onto your
PC with the necessary printer drivers.
transmissions of your device; in all
cases, please follow safety
guidelines closely.
Once the machine is incorporated into a WLAN network,
you can from your PC:
Radio infrastructure network
•
print documents on the multifunction machine from
your usual applications,
scan color, grey scale or black and white documents
on your PC.
In an infrastructure network, several devices
communicate via a central access point (a gateway or
router). All data is sent to the access point (gateway or
router) from where it is re-distributed.
•
The PC and all other devices must
have their parameters set up to the
same network as the multifunction
machine. All the details needed for
setting up the device, such as the
network names (SSID), type of radio
network, encryption key, IP address
or subnetwork mask, must match
the specifications of the network.
Important
You will find these details on your
PC or on the Access Point.
To find out how to set up the
parameters for your PC, please
consult the users’ manual for your
WLAN adaptor. For large networks,
please seek the advice of your
network administrator.
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Configure your network
You can be sure of perfect
communication if you use an
approved adaptor in conjunction with
your PC.
We recommend that the settings of
your WLAN network should only be
changed by a person with a good
knowledge of the configuration of your
computer.
Note
Note
All of the latest printer drivers for the
approved adaptor may be found on
our website together with further
information:
Creating or rejoining a network
Before attempting to use a WLAN adaptor on your
machine, you must enter the parameters that will allow a
WLAN network to recognise your machine.
Connect your WLAN adaptor
Your machine belongs to a new generation of terminals
that you can incorporate into a WLAN network using a
WLAN USB key.
On your machine you will find simple instructions
that guide you step by step through the set-up of your
network. Just follow them!
Your machine’s network radio
adaptor transmits data using the
radio protocol IEEE 802.11g; it can
also be incorporated into an existing
IEEE 802.11b network.
! 281 - SETUP / WLAN / CONFIG. ASS.
1 Type in !, select the menu SETUP using the keys
! or " and confirm with OK.
2 Select WLAN using the keys ! or " and confirm
with OK.
When connecting to your machine,
only use the approved adaptor.
Other transmitting or receiving
3 Select CONFIG. ASS. using the keys ! or " and
confirm with OK.
adaptors may damage your device.
Important
The machine searches for existing networks.
4 Select your existing network, or select NEW
NETWORK to create it, using the keys ! or " and
confirm with OK.
Irrespective of whether you use your
machine in an infrastructure or ad-
hoc network, you must set up certain
network and security parameters
(for example, the Service-Set-ID
(SSID) and the encryption key).
These must match the network’s
specifications.
If you choose an existing network,
steps 5 and 6 (and possibly 7) are
carried out automatically.
Note
5 SSID appears on the screen, enter the name of
your network using the numerical keypad, pressing
the keys one after the other until you obtain the
name you want (32 characters maximum) and
confirm with OK.
1 Plug your WLAN USB key into the USB port of your
machine.
6 AD-HOC MODE or INFRA. MODE appear on the
screen. Go back to the beginning of the chapter
and make your choice.
Select one of these modes and confirm with OK.
-
If you choose AD-HOC mode, the sub-menu
CHANNEL appears, enter a figure between 1
and 13 (1 to 11 for the US) and confirm with OK.
7 Select your encryption method, OFF, WEP or
WPA, and confirm with OK:
Please note that in ad-hoc mode,
the WPA/WPA2 encryption method
is not available.
Important
-
-
If you choose WEP, enter the WEP key that you
are using on your network.
The WEP key number may be
configured in the menu: ! 29 -
SETUP / TECHNICALS / WEP KEYS
Note
NBR.
If you choose WPA, enter the WPA or WPA2
key that you are using on your network.
- 25 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
8 IP CONF.: MANU or IP CONF.: AUTO appear on
3 Select PARAMETERS using the keys ! or " and
the screen.
confirm with OK.
If you choose to set up the system manually, go to
the next paragraph and enter the parameters
IP ADDRESS, SUBNET MASK and GATEWAY.
4 Select GATEWAY using the keys ! or " and
confirm with OK.
5 The number of your gateway will appear in the
format 000.000.000.000. Enter the new gateway
for your machine in the format displayed and
confirm with OK.
9 At the end of this procedure, you return to the main
menu of CONFIG. ASS.
10 Exit this menu by pressing the
key.
6 Exit this menu by pressing the
key.
Once the network has been set up, the LED of the WLAN
USB key should be on.
! 2825 - SETUP /WLAN / PARAMETERS / SSID
Referring to or changing your
network parameters
1 Type in !, select the menu SETUP using the keys
! or " and confirm with OK.
2 Select WLAN using the keys ! or " and confirm
Each of the parameters of your network may be changed
as your network develops.
with OK.
3 Select PARAMETERS using the keys ! or " and
! 2822 - SETUP / WLAN / PARAMETERS / IP
confirm with OK.
ADDRESS
4 Select SSID using the keys ! or " and confirm
with OK.
1 Type in !, select the menu SETUP using the keys
5 The name of your network will appear on the
screen. Enter the new name of your network and
confirm with OK.
! or " and confirm with OK.
2 Select WLAN using the keys ! or " and confirm
with OK.
6 Exit this menu by pressing the
key.
3 Select PARAMETERS using the keys ! or " and
confirm with OK.
4 Select IP ADDRESS using the keys ! or " and
! 2826 - SETUP / WLAN / PARAMETERS / MODE
confirm with OK.
1 Type in !, select the menu SETUP using the keys
5 The number of your IP address will appear in the
format 000.000.000.000. Enter the new IP address
for your machine in the format displayed and
confirm with OK.
! or " and confirm with OK.
2 Select WLAN using the keys ! or " and confirm
with OK.
6 Exit this menu by pressing the
key.
3 Select PARAMETERS using the keys ! or " and
confirm with OK.
4 Select MODE using the keys ! or " and confirm
! 2823 - SETUP / WLAN / PARAMETERS / SUBNET
with OK.
MASK
5 The symbol >>, tells you that your network is in
active mode.
1 Type in !, select the menu SETUP using the keys
6 Select one of the modes and confirm with OK.
! or " and confirm with OK.
-
If you choose the AD-HOC MODE, the sub-
menu CHANNEL will appear; enter a number
between 1 and 13 (1 to 11 for the US) and
confirm with OK.
2 Select WLAN using the keys ! or " and confirm
with OK.
3 Select PARAMETERS using the keys ! or " and
confirm with OK.
4 Select SUBNET MASK using the keys ! or " and
7 Exit this menu by pressing the
key.
confirm with OK.
In an AD-HOC network, the devices
communicate directly with each
other without passing through an
access point. The speed of
5 The number of your subnet mask will appear in the
format 000.000.000.000. Enter the new submask
of your machine in the format displayed and
confirm with OK.
communication across the whole
AD-HOC radio network is as fast as
the weakest connection in the
network. The speed of
communication is also dependent on
spatial distance between transmitter
and receiver, as well as the number
of barriers, such as walls or ceilings.
6 Exit this menu by pressing the
key.
Important
! 2824 - SETUP / WLAN / PARAMETERS / GATEWAY
1 Type in !, select the menu SETUP using the keys
! or " and confirm with OK.
2 Select WLAN using the keys ! or " and confirm
with OK.
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
! 2827 - SETUP / WLAN / PARAMETERS / SECURITY Once your connection has been set up, you must install
the network printer driver on your PC so that you can print
This parameter allows you to make your network secure your documents.
by setting the encryption method to use in your WLAN Refer to the paragraph Software installation, page 32.
network.
An example of how an AD-HOC network
1 Type in !, select the menu SETUP using the keys
may be set up
! or " and confirm with OK.
An example of how to configure an Ad-hoc network
without security protection using the following
parameters:
2 Select WLAN using the keys ! or " and confirm
with OK.
3 Select PARAMETERS using the keys ! or " and
confirm with OK.
•
•
•
•
•
•
•
•
network name: "house"
4 Select SECURITY using the keys ! or " and
radio type: "ad-hoc"
confirm with OK.
channel: "1"
5 Choose WEP, WPA or OFF and confirm with OK.
PC’s IP address: "169.254.0.1"
PC’s subnetwork mask: "255.255.0.0"
PC’s gateway: "0.0.0.0"
-
If you choose WEP, enter a password:
- In a 64 bit security configuration, the password
must contain five characters exactly.
- In a 128 bit security configuration, the
password must contain 13 characters exactly.
IP address of the multifunction machine: "169.254.0.2"
subnetwork mask of the multifunction machine:
"255.255.0.0"
You may also enter the password
using the hexadecimal system, if this
is the case:
•
multifunction machine’s gateway: "0.0.0.0"
- For a 64 bit security configuration,
the password must contain exactly
10 hexadecimal characters.
Setting up a multifunction machine
Note
1 Plug the WLAN USB key into the USB connector of
- For a 128 bit security configuration,
the password must contain exactly
26 hexadecimal characters.
the multifunction machine.
2 Type in !, select the menu SETUP using the keys
! or " and confirm with OK.
3 Select WLAN using the keys ! or " and confirm
-
If you choose WPA, enter a WPA or WPA2
password (min. 8 characters to 63 characters
max.).
with OK.
4 Select CONFIG. ASS. using the keys ! or " and
confirm with OK.
The password can contain alphanumerical
characters - numbers and letters - and any other
symbol available on the keypad. The only
invalid character is "€" (euro currency sign).
5 Select NEW NETWORK using the keys ! or "
and confirm with OK.
6 SSID appears on the screen, enter "house" using
the numerical keypad and confirm with OK.
6 Exit this menu by pressing the
key.
7 Select the mode AD-HOC MODE and confirm
with OK.
8 Enter "1" in the field CHANNEL and confirm
! 2828 - SETUP / WLAN / PARAMETERS /
with OK.
HOSTNAME
9 Select OFF and confirm with OK.
10 Select IP CONF.: MANU and confirm with OK.
The machine name allows you to identify your machine on
the network via a PC (for example with the name "PRINT-
NETWORK-1").
11 Enter "169.254.0.2" in the field IP ADDRESS and
confirm with OK.
12 Enter "255.255.0.0" in the field SUBNET MASK
1 Type in !, select the menu SETUP using the keys
and confirm with OK.
! or " and confirm with OK.
13 Enter "0.0.0.0" in the field GATEWAY and confirm
2 Select WLAN using the keys ! or " and confirm
with OK.
with OK.
14 At the end of this process, you return to the main
3 Select PARAMETERS using the keys ! or " and
menu of ASS. CONFIG.
confirm with OK.
15 Exit this menu by pressing the
key.
4 Select HOSTNAME using the keys ! or " and
confirm with OK.
Once the network has been set up, the LED of the WLAN
USB key should be on.
5 Type in the desired name (15 characters
maximum) and confirm with OK.
You must now set up the PC.
6 Exit this menu by pressing the
key.
- 27 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Setting up the PC
For this section, refer to the instructions supplied by the
manufacturer of the WLAN USB key to help you to find
and join the "house" network.
1 You may need to install the software for the WLAN
USB key on the PC, if this has not already been
done.
2 Plug WLAN USB key into a USB port on the PC.
3 Use the software of the WLAN USB key to detect
the network.
4 Join the network "house" once this has been
detected.
5 Now set up the WLAN network connection of your
PC.
To guide you through this stage, refer
to the paragraph “Setting the
parameters for a connection” in the
Note
manufacturer’s instructions.
To do this, you must configure the element
Protocol Internet (TCP/IP) for the WLAN
connection that has been created. If this element is
set up in such a way as to obtain an IP address
automatically, you must change it to manual mode
to set up the TCP/IP address ("169.254.0.1" in our
example), the subnet mask ("255.255.0.0" in our
example) and the default gateway ("0.0.0.0" in our
example).
6 Enter OK.
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
4 The list is shown in a table with the following
information:
USB memory key
-
the analysed files are indexed in an incremental
You can connect a USB memory Key on the front side of
your machine. The files stored in TXT, TIFF and JPEG
formats will be analysed and you will be able to use the
following actions:
1 by 1 order,
-
-
-
the files name with their extension,
the date of the files last save,
the files size in Kbytes.
- print the stored files contained in your USB memory
1
key ,
Print the files located in the key
- delete the files contained in your USB memory key,
- run an analysis on the contents of the inserted USB
memory key,
To print the files located in the key:
! 01 - MEDIA / PRINT DOC. / FILE
- digitalise a document on your USB memory key.
1 Insert the USB memory key on the front side of the
machine respecting the insertion way.
Use of the USB memory key
MEDIA ANALYSIS appears on the screen.
Always respect the insertion way
when you connect a USB memory
key to the machine.
Do not disconnect your USB memory
key while the machine is reading its
contents or writing contents.
2 Select PRINT DOC. with the ! or " buttons and
confirm with OK.
Important
3 Select FILE with the ! or " buttons and confirm
with OK.
4 You have three possibilities to print your files:
-
ALL, to print all the files located in the USB
memory key.
Select ALL with the ! or " buttons and
confirm with OK. The printing is started
automatically.
-
SERIES, to print a series of files located in the
USB memory key.
Select SERIES with the ! or " buttons and
confirm with OK.
FIRST FILE and the first indexed file appears
on the screen. Select with the ! or " buttons
the first file of the series to print and confirm
with OK. A star (*) appears on the left side of the
file.
LAST FILE appears on the screen. Select with
the ! or " buttons the last file of the series to
print and confirm with OK.
Press the
button.
Print your documents
COPIES NUMBER appears on the screen,
enter the desired number of copies with the
numerical keypad and confirm with OK.
Select the printing format (for JPEG files): A4 or
LETTER (depending on model), or PHOTO and
confirm with OK.
The printing is not possible on A5
Important
(or Statement) paper format.
You can print the stored files or a list of the files located in
the USB memory key.
Select the printing format: THICK or NORMAL
and confirm with OK to start printing.
Print the list of files located in the key
To print the list of files located in the key:
! 01 - MEDIA / PRINT DOC. / LIST
1 Insert the USB memory key on the front side of the
machine respecting the insertion way.
MEDIA ANALYSIS appears on the screen.
2 Select PRINT DOC. with the ! or " buttons and
confirm with OK.
3 Select LIST with the ! or " buttons and confirm
with OK.
1. It may be possible that some TIFF files of your USB
memory key cannot be printed due to data format limitation.
- 29 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
-
SELECTION, to print one or several files
located in the USB memory key.
5 Quit this menu by pressing the
button.
Select with the ! or " buttons the file to print
and confirm with OK. A star (*) appears on the
left side of the file.
Analyse the USB memory key content
Repeat this step for each file you want to print.
After a period of inactivity, your machine will return to the
main menu. To view the USB memory key again please
proceed as follows:
Press the
button.
COPIES NUMBER appears on the screen,
enter the desired number of copies with the
numerical keypad and confirm with OK.
! 07 - MEDIA / MEDIA ANALYSIS
1 Press !, enter 07 using the keypad.
2 The USB memory key analysis is started.
Select the printing format (for JPEG files): A4 or
LETTER (depending on model), or PHOTO and
confirm with OK.
Select the printing format: THICK or NORMAL
and confirm with OK to start printing.
3 You can print or delete the detected files located in
your USB memory key. Refer to the previous
chapters.
Save a document on a USB memory
key
5 Quit this menu by pressing the
button.
Delete your files located in the key
This function allows you to digitise and save a document
directly in the folder OKI MB260\SCAN on a USB memory
key. The folder OKI MB260\SCAN is created by the
You can delete files located in your USB memory key.
! 06 - MEDIA / DELETE / MANUAL application.
1 Insert the USB memory key on the front side of the
machine respecting the insertion way.
Before digitalising a document,
make sure that your USB memory
key has sufficient disk space. If not,
you can delete manually the files,
MEDIA ANALYSIS appears on the screen.
Important
2 Select DELETE with the ! or " buttons and
confirm with OK.
3 Select MANUAL with the ! or " buttons and
confirm with OK.
1 Place the document to be copied face down on the
4 You have three possibilities to delete your files:
glass.
-
ALL, to delete all the files located in the USB
memory key.
2 Insert the USB memory key on the front side of the
machine respecting the insertion way.
The USB memory key analysis is started.
When the analysis is finished, the MEDIA menu is
displayed.
Select ALL with the ! or " buttons and
confirm with OK.
You come back to the previous menu.
-
SERIES, to delete a series of files located in the
USB memory key.
3 Select SCAN TO with the ! or " buttons then
confirm with the OK button.
Select SERIES with the ! or " buttons and
confirm with OK.
FIRST FILE and the first indexed file appears
on the screen. Select with the ! or " buttons
the first file of the series to delete and confirm
with OK. A star (*) appears on the left of the file.
LAST FILE appears on the screen, select with
the ! or " buttons the last file of the series to
delete and confirm with OK. A star (*) appears
on the left side of the file.
You can also access this function in
two other ways:
•
•
by pressing the
button then
Important
by selecting SCAN-TO-MEDIA.
by pressing the ! button from the
screen saver then by typing 03 on
the numerical keypad.
Press the
button.
4 Choose between B&W SCAN or COLOR SCAN with
You come back to the previous menu.
the ! or " buttons and confirm with OK.
-
SELECTION, to delete only one or several files
located in the USB memory key.
Select with the ! or " buttons the file to delete
and confirm with OK. A star (*) appears on the
left side of the file.
5 With the alphanumerical keypad, give a name to
the scan file (up to 20 characters) and confirm
with OK.
6 Choose the scan format between IMAGE and PDF,
and confirm to start the scan and the recording of
the document.
Repeat this step for each file you want to delete.
IMAGE allows to have the same kind of file as a
photo. PDF is a format for the digital documents
creation.
Press the
button.
You come back to the previous menu.
- 30 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
With the IMAGE format, if you have
selected:
•
•
BLACK&WHITE, the picture will
be saved in TIFF format.
COLOR, the picture will be saved
in JPEG format.
You can choose the image resolution
that will be digitized to the USB
memory key; the default resolution is
AUTO.
Important
Press the
button several times
and select the resolution you require:
•
•
Scanning in BLACK&WHITE:
-
-
icon: text resolution.
icon: photo resolution.
- no icon: auto resolution.
Scanning in COLOR:
-
icon: text resolution.
- no icon: auto resolution.
The beginning button
immediately starts the scan
and sends a file to the support with the parameters
defined in the analysis format.
- 31 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Software installation
PC Features
Introduction
This section describes the following installation
procedures:
•
•
full installation of the Companion Suite Pro software,
installation of the drivers only.
The Companion Suite Pro software allows the connection
of a personal computer with a compatible multifunction
machine.
Installing the full software package
Turn your PC on. Open an account session with the
administration rights.
From the PC, you can:
•
•
•
manage the multifunction machine, allowing you to set
it up according to your needs,
1 Open the CD-ROM drive, insert the installation CD-
print your documents on the multifunction machine
from your usual applications,
ROM and close the drive.
2 An installation procedure is automatically run (Auto
run). If it does not, double-click on setup.exe at the
CD-ROM's root.
scan color, grey scale or black and white documents
and edit them on your PC.
3 A screen titled COMPANION SUITE PRO LL2
appears. This screen allows you to install and
uninstall the software, access the product's user
guides or browse the CD-ROM contents.
Configuration requirements
The minimum configuration requirements for your
personal computer are:
4 Place your cursor on INSTALL PRODUCTS and
confirm with left-click of the mouse.
Supported operating systems:
5 The Products Installation screen appears.
Place your cursor on ALL PRODUCTS and confirm by
left-click with the mouse.
•
•
Windows 2000 with at least Service Pack 4,
Windows XP x86 (Home and Pro) with at least Service
Pack 1,
The full installation copies on your
hard disk the software required for the
good execution of the Companion
Suite Pro kit, which is:
- Companion Suite Pro (machine
management software, printer drivers,
scanner, ...),
•
•
•
•
Windows 2003 server for printing driver only,
Windows Vista (32 and 64 bit),
Mac OS 10.3 to 10.5,
Linux (Redhat 9.0, Debian 4.0, Suse 10.2, Fedora 7
and Ubuntu 7.10).
See Mac/Linux CD ROM for more
information about installation
instruction.
- Adobe Acrobat Reader,
- PaperPort.
You may already be the owner of a
version of the software available in the
installation CD-ROM.
Note
Note
Processor:
In this case use the CUSTOMIZED
installation, select the software that
you want to install on your hard drive
and confirm your choice.
•
•
•
800 MHz for Windows 2000,
1 GHz for Windows XP x86 (Home and Pro),
1 GHz for Windows Vista (32 and 64 bit).
A CD-ROM drive
A free USB port or LAN port
6 The welcome screen appears. Click on the NEXT
button to launch the installation of the Companion
Suite Pro in your PC.
600 Mbytes of available disk space for the installation
RAM memory:
•
•
128 Mbytes minimum for Windows 2000,
192 Mbytes minimum for Windows XP x86 (Home and
Pro),
•
1 GByte for Windows Vista (32 and 64 bit).
7 To continue, you need to accept the proposed
- 32 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
license agreement.
Installing drivers only
This section describes the following installation
procedures:
•
•
installation of drivers using the Companion Suite Pro
software,
manual installation of drivers.
Installing the drivers using the Companion Suite
Pro software
Turn your PC on. Open an account session with the
administration rights.
1 Open the CD-ROM drive, insert the installation CD-
8 Click on the NEXT button.
ROM and close the drive.
9 The final installation is ready to be executed. Click
2 An installation procedure is automatically run (Auto
run). If it does not, double-click on setup.exe at the
CD-ROM's root.
on the INSTALL button.
3 A screen titled COMPANION SUITE PRO LL2
appears. This screen allows you to install and
uninstall the software, access the product's user
guides or browse the CD-ROM contents.
4 Place your cursor on INSTALL PRODUCTS and
confirm with left-click of the mouse.
5 The Products Installation screen appears.
Place your cursor on CUSTOMIZED and confirm by
left-click with the mouse.
6 Place your cursor on COMPANION SUITE PRO LL2
and confirm with left-click of the mouse.
7 The welcome screen appears. Click on the NEXT
button to launch the installation of the Companion
Suite Pro kit on your PC.
The following screen appears to indicate the
progression of the installation.
10 Click on OK to finish the installation.
8 To continue, you need to accept the proposed
license agreement.
Your Companion Suite Pro kit is successfully installed on
your PC.
You can now connect your multifunction machine, refer to
You can start the multifunction machine's management
software from the menu START > ALL PROGRAMS
> OKIDATA > COMPANION SUITE PRO LL2
> COMPANION DIRECTOR or by clicking on the icon
COMPANION - DIRECTOR located on your desktop.
- 33 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
9 Click on the NEXT button.
14 Click on OK to finish the installation.
10 Select INSTALL DRIVERS in the list and click on the
NEXT button.
The Companion Suite Pro software is now installed on
your PC.
You can now connect your multifunction machine, refer to
11 Select the destination folder for installation and
click on the NEXT button.
Installing the drivers manually
You can install the printer and scan drivers manually
without running any setup software.
This installation mode is only possible
on Windows 2000, XP and Vista.
Note
1 Locate your USB cable connectors and connect as
shown below on the picture.
12 The final installation is ready to be executed. Click
on the INSTALL button.
2 Power on your multifunction machine.
The PC detects the device.
3 Click on LOCATE AND INSTALL DRIVER SOFTWARE
(RECOMMENDED).
13 A screen informs you of the installation progress.
- 34 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
The following screen appears:
1 Locate your USB cable connectors and connect as
shown below on the picture.
4 Open the CD-ROM drive, insert the installation CD-
ROM and close the drive.
The drivers are detected automatically.
2 Power on your multifunction machine.
The PC detects the device and the drivers are
automatically installed.
5 Select OKI MB260 in the list and click on NEXT.
3 Once the installation is finished, a message
indicates that the drivers are installed correctly.
You can now use the multifunction machine to print or
scan your documents.
6 A screen informs you that the drivers have been
installed. Click on the CLOSE button.
You can now use the multifunction machine to print or
scan your documents.
Connections
Make sure that your multifunction machine is powered off.
The connection between the PC and the machine
requires a USB 2.0 shielded cable no more than 3 meters
long.
It is recommended to install the
Companion Suite Pro software first
and then to connect the USB cable
If you connect the USB cable before
installing the Companion Suite Pro
software the recognition system
(plug and play) identifies
Important
automatically that new hardware has
been added. To start your machine
drivers installation, refer to
instructions on screen. When you
use this procedure, only printing and
scanning functions are activated.
- 35 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Multifunction Terminal's Supervision Companion Monitor
The software that you have installed contains two
multifunction machine management applications,
Graphical presentation
COMPANION DIRECTOR and COMPANION MONITOR, which
allow you to:
Run the application by clicking on the COMPANION
MONITOR icon located on your desktop or from the menu
START >ALLPROGRAMS >OKIDATA >COMPANION SUITE
PRO LL2 > COMPANION MONITOR.
•
check whether the multifunction machine is connected
to your PC,
•
•
monitor the multifunction machine activities,
monitor the status of the multifunction machine
consumables from the PC,
•
quickly access the graphic editor applications.
To manage the multifunction machine, run the
Companion Director application by clicking on the icon
located on your desktop or from the menu START
>ALLPROGRAMS > OKIDATA >COMPANION SUITE PRO
LL2 > COMPANION DIRECTOR.
Checking the connection between the PC
and the multifunction machine
To check if the connection between the devices is good,
run the COMPANION MONITOR software from the icon
located on the desktop and check that the same
information is displayed on the multifunction machine.
From this screen you can monitor the information or
configure your multifunction machine from the tabs:
•
•
•
DEVICE SELECTION: Displays the list of devices
managed by the PC.
Companion Director
COMPANION: Presents the multifunction machine
screen (USB connection only).
This graphical Interface allows you to run the utilities and
the software to manage your multifunction machine.
CONSUMABLES: Displays the consumables status.
Graphical presentation
Device management
Run the application by clicking on the COMPANION
DIRECTOR icon located on your desktop or from the menu
START >ALLPROGRAMS > OKIDATA >COMPANION SUITE
PRO LL2 > COMPANION DIRECTOR.
This tab shows the list of devices managed by the PC.
Selecting the current device
Only one device at a time may be connected to the PC.
The current device may be selected by clicking on the
radio button corresponding to the device.
Utilities and applications activation
The Companion Suite Pro graphical interface allows you
to run the following utilities and software:
•
•
get HELP from the current documentation,
run the PAPERPORT software (Doc Manager).
To run a software or utility contained in the Companion
Suite Pro kit, place the cursor on it and left-click with the
mouse.
- 36 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
3 Select the desired scan RESOLUTION in the drop-
Status of the connection
down menu.
The status of the connection between the current device
and the PC is indicated by a color. The following table
defines the possible states of the connection.
Color
State
Yellow
Connection in progress.
Green
Red
Connection established.
The PC cannot connect to the device.
Check the USB connection.
Device parameters
4 Click OK to confirm the new parameters.
1 Select a device by clicking on its line in the list and
click on PROPERTIES to configure the scanning
parameters to be applied for this device when you
use the SCAN TO function.
Removing a device
1 Select the device from the list and click the minus
sign or REMOVE button.
2 To confirm the removal of the device, click YES. To
cancel the removal, click NO.
The device is no longer displayed in the list.
Display the consumable status
2 Select the desired scan MODE in the drop-down
The following information will be available from the
CONSUMABLES tab:
menu.
•
•
•
current consumables status,
number of printed pages,
number of scanned pages.
- 37 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
To scan a document from PaperPort:
Companion Suite Pro functionalities
1 Click on FILE > SCAN.
Document analysis
2 Select the desired scanner.
The document analysis can be carried out in two ways:
•
either by the SCAN TO function (application accessible
from the Companion Director window or from the
SCAN button on the machine),
•
or directly from a standard compatible application.
Analysis with Scan To
Run the application by clicking on the COMPANION
DIRECTOR icon located on your desktop or from the menu
START >ALL PROGRAMS > OKIDATA > COMPANION SUITE
PRO LL2 > COMPANION DIRECTOR.
3 Customise the advanced properties of the
digitisation by clicking on the ADJUST THE QUALITY
OF THE SCANNED PICTURE link.
4 Adjust the desired parameters and click on the OK
button.
1 Click on the SCAN TO graphical image or press the
SCAN button on your machine and select SCAN-
TO-PC.
2 You can follow the ongoing digitisation on a screen.
5 Click on the SCAN button, you can follow the
ongoing digitisation on a screen.
Printing
You have the possibility to print your documents via the
USB connection or the WLAN connection.
3 At the end of the digitisation, the scanned picture
appears in the PaperPort window.
During the installation of the Companion Suite Pro
software, the OKI MB260 printer driver will be installed
automatically onto your PC.
Printing on the multifunction machine
Printing a document on the multifunction machine from
your PC is like printing a document in Windows.
1 Use the PRINT command from the FILE menu of the
currently open application on the screen.
2 Select the OKI MB260 printer.
If the PaperPort software is not
installed on your hard drive, the
scanned picture will appear on your
Note
desktop in TIFF format.
- 38 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Printing in duplex mode with the multifunction
machine
The PC generates and prints a page
explaining how to reload the sheets
for a duplex job. Read this page
carefully and place it back with the
other sheets.
The machine offers the possibility to print a document in
manual duplex mode from your PC.
Important
it is very important that you return
the explanation sheet to the paper
tray to continue printing correctly.
In manual duplex, the print
quality and paper transport are
not guaranteed.
7 Place the sheets in the paper tray as indicated on
the explanation page and below.
- If some trouble occurred to the
paper during the print of the first
side, such as wrinkle, dog ear or
staple, do not use the paper for
The following illustrations describe the necessary
operations depending on the selected binding
mode:
CAUTION
manual duplex.
•
Long sides
- When you load paper, please
true up the end of paper on a flat
surface.
For best results, we recommend
that you use 80 g/m² A4 paper or
20 lbs/m² Letter paper.
To print a document in manual duplex mode:
The duplex printing mode is
available only in a paper format
managed by the paper tray.
The manual tray cannot be used to
print in duplex mode.
Important
1 Use the PRINT command from the FILE menu of the
currently open application on the screen.
2 Select the OKI MB260 printer.
3 Check the Duplex box and choose among the two
•
Short sides
binding modes:
Binding mode
Long sides
Printing
Short sides
4 Click on the OK button to begin printing.
5 The machine prints the odd pages (from the higher
odd page to page 1) and the LCD screen displays:
8 Press OK on the command panel to resume
** PRINTING **
** PC **
printing.
9 Even pages are printed on the other side of the
sheets. Once all pages are printed, remove the
explanation sheet.
6 Once the odd pages are printed, the LCD screen
displays the message **PUT THE PRINTED SHEETS IN
THE PAPER TRAY WITH THE PRINTED SIDE VISIBLE...:
If a paper jam or a paper format
error occurs, the job is cancelled.
You must then resubmit the print job.
Important
** PUT THE PRIN
... AND PRESS <OK>
- 39 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Uninstall the drivers using the Companion Suite
Pro software
Software Uninstallation
This section describes the following procedures:
Run the programs removal from the menu START
>ALL PROGRAMS >OKIDATA >COMPANION SUITE PRO
LL2 > UNINSTALL.
•
•
full uninstallation of the Companion Suite Pro
software,
uninstallation of the drivers only.
You can also uninstall COMPANION
SUITE PRO LL2 drivers using the
Windows function ADD/REMOVE
Note
Uninstall the software from your PC
PROGRAMS from the control panel.
Turn your PC on. Open an account session with the
administration rights.
1 A confirmation screen appears. Click on the YES
button to continue the COMPANION SUITE PRO LL2
drivers program removal.
Run the programs removal from the menu START
>ALL PROGRAMS >OKIDATA > COMPANION SUITE PRO
LL2 > UNINSTALL.
1 A confirmation screen appears. Click on the YES
button to continue the Companion Suite Pro
program removal.
2 The uninstall program is launched. You can cancel
the removal by clicking on CANCEL.
2 The uninstall program is launched. You can cancel
the removal by clicking on CANCEL.
Uninstall the drivers manually
The following drivers must be removed:
•
•
•
print driver
scan driver
modem driver
3 Click on the OK button.
To remove the print driver:
1 Open the PRINTERS window (START > CONTROL
PANEL > PRINTERS AND FAXES or START > CONTROL
PANEL > HARDWARE AND SOUND > PRINTERS,
depending the operating system).
4 You need to restart your system at the end of the
2 Delete the OKI MB260 icon.
procedure. Click on the YES button.
3 In the PRINTERS window, right-click with the mouse
and select RUN AS ADMINISTRATOR > SERVER
PROPERTIES.
4 Select the DRIVERS tab.
5 Select the OKI MB260 driver and click on the
REMOVE button.
Uninstall the drivers from your PC
Turn your PC on. Open an account session with the
administration rights.
Depending on the installation mode used, select the
required uninstallation mode:
•
If you have installed the drivers with the Companion
Suite Pro software, see paragraph Uninstall the
•
If you have installed the drivers manually, see
- 40 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
6 Select the option REMOVE DRIVER AND DRIVER
PACKAGE and click on the OK button.
7 A confirmation screen appears. Click on the YES
button to continue.
8 Click on the DELETE button to confirm the removal.
To remove scan and modem drivers:
1 Open the DEVICE MANAGER window (START
>CONTROL PANEL > SYSTEM > HARDWARE > DEVICE
MANAGER or START >CONTROL PANEL > HARDWARE
AND SOUND > DEVICE MANAGER, depending on the
operating system).
2 In the OTHER DEVICES sub-menu, select the OKI
MB260 item and click on the right button of the
mouse.
3 Select UNINSTALL on the menu and left-click with
the mouse.
4 Click on the OK button to confirm the removal.
5 In the IMAGING DEVICES sub-menu, select the OKI
MB260 item and right-click with the mouse.
6 Select UNINSTALL on the menu and left-click with
the mouse.
7 Click on the OK button to confirm the removal.
- 41 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
To replace the toner cartridge, proceed as shown below.
Maintenance
1 Insert the smart card provided with the new toner
cartridge as shown on the picture below.
Service
General information
For your safety, it is imperative to
refer to the security directives
presented in the Safety booklet.
CAUTI
ON
The following message appears:
To ensure that your machine is kept in the best
conditions, it is recommended that you periodically clean
the inner parts.
CHANGE TONER?
YES=OK - NO=C
Please respect the following rules while using this
machine:
2 Press OK.
The following message appears:
- Do not leave the scanner cover open.
- Do not try to lubricate the device.
- Do not close the scanner cover violently or do not
apply vibrations to the machine.
- Do not open the cartridge access cover while printing.
- Do not try to disassemble the machine.
- Do not use paper which has stayed in the tray for too
long.
OPEN FRONT COVER
REPLACE TONER
3 Stand in front of the device.
4 Push on the left and right sides of the cover and pull
it towards you.
5 Raise and remove the toner cartridge from the
machine.
6 Unpack the new cartridge and insert it into the slot
Toner cartridge replacement
as indicated in the diagram below.
Your machine comes with a current consumable
management system. It tells you if your toner cartridge is
close to its end of cycle.
The following messages will appear on your machine
screen when the toner cartridge reaches the critical
threshold (less than 10% toner cartridge left) and when it
is empty:
TONER NEAR
END
TONER EMPTY
REPLACE <OK>
You can however change the toner cartridge at any time,
before it reaches its end of cycle.
Always use the smart card provided
when replacing the toner cartridge.
The smart card contains the
information necessary to reset the
level of toner. Replacing the toner
Importa
cartridge without using a smart card
may result in the consumable
management system being
inaccurate.
nt
7 Close the cover.
The following message appears:
HAVE YOU CHANGED
THE TONER? <OK>
8 Press OK.
- 42 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
A wait message appears.
Printer issues
PLEASE
WAIT
Error messages
The smart card is read.
When the printer encounters any of the problems
described below, the corresponding message is shown
on the machine display.
NEW TONER
REMOVE CARD
Message
Action
9 Remove the smart card from the reader, your
machine is ready to print again.
Check the presence of a
toner cartridge in the
machine.
CHECK TONER
Issues with smart cards
If you use a smart card that has already been used, the
machine will display:
Indicates that your
consumable will need
changing soon.
TONER NEAR END
PLEASE
WAIT
REPLACE PAPER
HEATING
Add paper in tray.
then,
Message displayed when
starting the machine.
REMOVE CARD
ALREADY USED
If you use a defective smart card, the machine will display:
The printer front cover is
open, close it.
CLOSE COVER
PRINTER
PLEASE
WAIT
Replace the toner
cartridge.
TONER EMPTY
REPLACE <OK>
then,
UNKNOWN CARD
REMOVE CARD
A sheet of paper is
jammed in the machine.
Take out the toner
If the C button is pressed while the smart card is being
cartridge and remove the
jammed paper sheet.
Take out the paper tray
and remove the jammed
paper sheet. Then open
and close the consumable
cover.
read, the machine displays:
PAPER JAM
REMOVE TONER
ACTION CANCELLED
REMOVE CARD
Cleaning
Scanner reading system cleaning
A sheet of paper is
When one or more vertical lines appear on the copies,
clean the glass of the scanner.
jammed in the machine.
Open the paper jam
cover. Remove the
jammed paper sheet.
Then open and close the
consumable cover.
PAPER JAM
EXTERNAL TRAY
1 Open the scanner cover until it is standing in
vertical position.
2 Wipe the glass with a soft lint-free cloth soaked with
mild alcohol.
3 Close the scanner cover.
4 Make a copy to check that the symptoms have
Add paper in the paper
tray.
PAPER EMPTY
disappeared.
Printer cleaning
After one of the error messages listed
above is displayed, it may happen that
the active print job is cancelled (see
Dust, dirtiness and paper debris on the external and
internal surfaces of the printer can affect its operation. We
advise that it is cleaned regularly.
Note
Printer external cleaning
Clean the external part of the printer with a soft cloth
soaked in mild detergent.
- 43 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Paper jam
PC printing issues
When printing, a sheet of paper may get stuck in the
printer or the paper tray and cause a paper jam.
This section details how the machine handles a print
request after having encountered an issue (paper jam,
connection loss, etc.).
In case of a paper jam in the machine, the following
message appears:
Refer to the sections below to know if the printing of your
document will resume or will be cancelled, depending on:
PAPER JAM
•
•
the connection to the PC,
EXTERNAL TRAY
the problem encountered during printing.
1 Open the paper jam cover located at the back of
the machine.
PC printing via USB connection
2 Remove the jammed sheet of paper and close the
cover.
Issue encountered
Print request handling
Once the problem is
resolved, printing resumes
from the first non-printed
page.
Paper empty
No paper feed
Paper jam
Once the problem is
resolved, printing resumes
from the first non-printed
page.
Exception: If the document
was to be printed in manual
duplex mode, the printing
of the document is
Paper format
problem
3 Open and close the front cover.
The printer starts again automatically.
cancelled.
The fusion unit can reach a very
high temperature during the
CAUTI
The printing of the active
document is cancelled.
Documents waiting to be
printed, however, will print
after the toner cartridge is
replaced.
operation. To prevent any harm, do
not touch this area. For details,
refer to “Positions of Safety labels
ON
Toner empty
In case of paper jam, the following message appears:
PAPER JAM
REMOVE TONER
The machine switches to
idle mode after a timeout
(30 seconds by default).
The printing of the active
document is cancelled.
Documents waiting to be
printed, however, will be
printed.
1 Remove the toner cartridge and check if a sheet is
jammed.
2 Remove the sheet of paper which causes the paper
Pause requested
from the spooler
jam.
3 Put the toner cartridge in the machine, or remove
the paper tray and remove the sheet of paper which
causes the paper jam.
4 Check that the paper sheets in the paper tray are
correctly placed.
Once the problem is
resolved, the printing of
the document restarts from
the beginning, regardless
of the number of pages
already printed before the
connection loss.
Loss of USB
connection
5 Replace the paper tray in the machine.
- 44 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
PC printing via WLAN connection
Issue encountered
Print request handling
Once the problem is
resolved, printing resumes
from the first non-printed
page.
Paper empty
No paper feed
Paper jam
Once the problem is
resolved, printing resumes
from the first non-printed
page.
Exception: If the document
was to be printed in manual
duplex mode, the printing
of the document is
Paper format
problem
cancelled.
The printing of the active
document is cancelled.
Documents waiting to be
printed, however, will be
printed.
Toner empty
or
Printing resumes from the
first non-printed page.
The machine switches to
idle mode after a timeout
(30 seconds by default).
The printing of the active
document is cancelled.
Documents waiting to be
printed, however, will be
printed.
Pause requested
from the spooler
Once the problem is
resolved, the printing of
the document restarts from
the beginning, regardless
of the number of pages
already printed before the
connection loss.
Loss of WLAN
connection
- 45 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Specifications
Physical specifications
Dimensions:
Weight:
344 x 447 x 386 mm
11.6 kg
Electrical specifications
Power supply (see rating plate):
Single phase 120 V - 50/60 Hz - 8.5 A or
single phase 220-240 V - 50/60 Hz - 4.5 A
according model (see rating plate)
10 W typical in powersave
Electric consumption:
33 W typical in standby
450 W average during printing (900W peak)
Environmental specifications
Operating temperature:
10 °C to 27 °C [50 °F to 80.6 °F] with an ambient humidity
included between 15 to 80% (up to 32°C [89.6 °F] with an
ambient humidity included between 15 to 54%)
Peripheral specifications
Printer
Type:
Laser (on normal paper)
600 dpi
Resolution:
Speed:
a
20 ppm maximum
21 sec.
13 sec.
Preheating time:
First page out time:
a. Printing speed may vary depending on used operating systems, computer specifications, software applications,
connection modes (USB or WLAN), paper formats as well as file types and sizes.
Copier
Type:
Autonomous Black and White
20 ppm maximum
600 dpi
99 pages maximum
25 % to 400 %
Copy speed:
Resolution:
Multiple copies:
Zoom range:
Scanner
Type:
Color scanner
36 bits
600 dpi (optical)
2400 dpi (interpolated)
TWAIN, WIA
Letter
Color depth:
Resolution:
Software compatibility:
Maximum paper format:
Printing supports
Main paper tray capacity:
250 sheets maximum (60 g/m²), 200 sheets maximum (80 g/
m²)
50 sheets
Output tray capacity:
- 46 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Main tray paper format:
A4, A5, Statement, Legal, Letter
60 to 105 g/m² paper
A4, A5, Statement, Legal, Letter, B5, exec, A6
52 to 160 g/m² paper
Paper format for manual printing:
PC connection
Slave USB 2.0 port (PC connection)
Master USB 2.0 port (Wlan connection, reader, USB memory key reader)
Operating System: Windows 2000 ≥ SP4, Windows XP x86 ≥ SP1, Windows Vista, Windows 2003 server
(for printing only)
Consumable specifications
Reference paper
Scanner :
Printer :
Inapa tecno SPEED A4
Ricoh T6200 A4
Specifications are subject to changes for improvement without notice.
- 47 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Replacement
Toner
Toner Cartridge Part Number
56123401
The standard toner cartridge can produce up to
4,000 pages (when printing on Letter paper with a
5% max. black and white ratio).
The initial toner cartridge can produce up to 1,500
pages (when printing on Letter paper with a 5%
max. black-and-white ratio).
The service life of the toner cartridge mainly
depends on the type of printed document and the
average number of pages per print operation).
- 48 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MB260
Service and
Support
First...
Consult the store where you purchased your
printer.
Additional OKI Resources
•
•
Available 24 hours a day, 7 days a week
Visit our multilingual web site:
www.OKIPRINTINGSOLUTIONS.COM
•
•
Visit MY.OKIDATA.COM
Call 1-800-654-3282 (U.S. and Canada only)
- 49 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|