USER’S MANUAL
©2002
Industries
Download from Www.Somanuals.com. All Manuals Search And Download.
PPD01
VERY IMPORTANT – MIXER CARE
Please read this entire manual before connecting this unit to your system
For optimum performance:
•
•
All the slide faders are user replaceable items and subject to wear. Excessive force can wear out the fader quickly. This is not a
warranted item.
Never use spray cleaners on the slide controls. Residues cause excessive dirt build-up and this will void your warranty. In
normal use slide controls can last for many years. If they malfunction (usually because of a dirty or dusty environment) consult
a professional technician.
•
•
Always make sure that AC power is OFF while making any connections.
Use appropriate cables throughout your system. Do not use excessively long cables (i.e. over 50ft/14m) Be sure plugs and jacks
are tightly mated. Loose connections can cause hum, noise or intermittents that could easily damage your speakers. Make the
input and output connections with readily available low-capacitance stereo cables. Quality cable makes a big difference in audio
fidelity and punch. See your Numark dealer or an electronics or audio specialist store if you are not sure which cables to get.
•
•
Never attempt to make any adjustments or repairs other than those described in this manual. Take the unit to your dealer or to
an authorized Numark Service Center.
ALWAYS remember: “TURN AMPS ON LAST AND OFF FIRST”. Begin with master faders or volume controls on minimum and the
amplifier gain/input control(s) down. Wait 8 to 10 seconds before turning up the volume. This prevents transients which may
cause severe speaker damage.
•
•
Use restraint when operating controls. Try to move them slowly. Rapid adjustments could damage speakers due to amplifier
clipping.
Avoid amplifier “clipping” at all costs: this occurs when the red LEDs (usually on the front panel of most professional power
amplifiers) start flashing. “Clipping” is when the power amplifier is distorting and working beyond it’s limits. Amplifier distortion
is THE major cause of speaker failure.
•
•
To prevent fire or shock hazard, do not expose the unit to rain or moisture. Never place cans of beer, soda, glasses of water or
anything wet on top of the unit!
The headphone outputs can be set to levels which can cause damage to your ears. Use caution.
CHECK TO BE SURE
THE FOLLOWING ITEMS ARE IN THIS BOX:
•
•
•
MIXER
OWNERS MANUAL (THIS BOOKLET)
POWER SUPPLY
- The Leader in DJ Technology
©2002 Numark Industries
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PPD01
®
CONGRATULATIONS...
You have just purchased a digital mixer designed specifically for the professional DJ. This unit has
been designed with the latest digital technology to offer premium performance and effects. Several
innovative features are included to ensure maximum results from your performance.
Once again, congratulations and thank you for making the PPD01 your choice in professional DJ
Mixers.
Features:
•
World’s only 24-bit Digital 2 Channel Mixer with a S/N ratio
of >102dB*, 0.005% THD+N, full path
•
World’s first mixer with all Digital, Replaceable, and
Interchangeable VCA Faders with slope and reverse
controls.
•
•
World’s first mixer with 8 digital crossfader functions for
various DJing styles.
World’s first Dual Mode tone controls on each channel
Mode a) 3-band Digital EQ-KILLS
Mode b) Low Pass/Band Pass/High Pass filter option with
sweepable frequency and resonance (Q)
•
•
8-position phono/line switches.
Look-ahead peak limiters on the master and headphone
outputs to avoid clipping
•
•
•
Mini-crossfader cueing with headphone tone control.
Master Balanced, Booth, Optical and Coax Digital outputs.
2 Phono, 5 Line, 1 Mic Inputs.
*A weighted
Please record the serial number of your unit as shown on the back of the chassis as well as the name of
the dealer from whom you purchased the unit. Retain this information and your original purchase
receipt for your records. Please return the enclosed warranty card to register your CD player with us.
MODEL: PPD01
SERIAL NUMBER:
PURCHASED FROM:
DATE OF PURCHASE:
- The Leader in DJ Technology
©2002 Numark Industries
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PPD01
TABLE OF CONTENTS
Safety Instructions
2
3
4
5
Mixer Care and Included Items
Introduction and Registration
Specifications
Description of the Features
Face Panel
6
9
Rear Panel
Set-up & Connections
Crossfader Features
Warranty
10
11
12
- The Leader in DJ Technology
©2002 Numark Industries
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PPD01
FRONT PANEL FEATURES
- The Leader in DJ Technology
©2002 Numark Industries
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PPD01
Microphone - Auxiliary Input Controls
1. “MIC – AUX GAIN” (Microphone - Auxiliary Gain): This knob adjusts the volume of both the main microphone and
auxiliary inputs. The gain should be turned completely to off when connecting and disconnecting equipment. If both inputs
are used simultaneously the inputs will be mixed together.
2. “Treble” (Microphone - Auxiliary High EQ): This knob adjusts the high-tone input sound of the microphone.
3. “Bass” (Microphone - Auxiliary Low EQ): This knob adjusts the low-tone input sound of the microphone.
4. “Microphone” (Quarter Inch Microphone Input): One microphone can be connected to this Quarter Inch input terminal.
Primary Mixing Channel Controls
5. “Gain Knob” (Input Level Trim): This rotary control adjusts the pre-fader input signal levels of the inputs. This level
adjustment should be used with the pre-fader meter to match levels of both input channels.
6. “Filter Mode Button” (Control Mode Select): This button toggles the control knob mode between EQ and Filter. When
the indicator light is on, the three knobs control a classic filter (Type, Resonance, Frequency). When the indicator light is
off, the 3 tone knobs control a 3-band EQ (Bass, Mid, Treble).
WARNING: When switching mode the user should take care when setting and releasing levels.
Excessive output can occur if levels or effects are released when set too high. This could lead to
equipment or hearing damage.
Note: If the user pushes and holds this button, the parameter of the knobs will be held constant until released. In
this way the user can pre-set the knobs to a desired effect position without the change being heard until the button
is released.
7. Control Knobs: These knobs control the post gain and pre line fader audio signal. Their function is determined by the
“Filter Mode Button” position
EQ Mode
“Treble” (Input Level High EQ): This rotary control adjusts the high-tone sound of the inputs. Turning the knob
completely to the right increases the level, turning the knob completely to the left decreases the level to off. This
music “KILL” control allows for unique mixing styles.
“Middle” (Input Level Midrange EQ): This rotary control adjusts the high-tone sound of the inputs. Turning the
knob completely to the right increases the level, turning the knob completely to the left decreases the level to off.
This music “KILL” control allows for unique mixing styles.
“Bass” (Input Level Low EQ): This rotary control adjusts the high-tone sound of the inputs. Turning the knob
completely to the right increases the level, turning the knob completely to the left decreases the level to off. This
music “KILL” control allows for unique mixing styles.
Filter mode
“Type Knob” (Filter Select): This rotary control continuously fades between Low-Pass, Band-Pass & High-Pass
Filter.
“Frequency Knob”(Frequency Select): This rotary control sweeps between 60-20kHz center frequency.
“Resonance Knob” (Intensity Control): This rotary control controls the resonant peak at the center frequency.
8. “Phono(AUX)/Line Switch” (Input Selector Switch): These two-position toggles select what input source is engaged
among the connected units (see “Connection Diagram” for details on connecting sources.) These toggles can be rotated
to suit your mixing preferences by removing the top Mixer Panel and adjusting their position.
9. “Input Level Slider” (VCA Fader): These slide faders adjust the level for CH-1 or CH-2 respectively.
Note: This fader is user replaceable if it should ever wear out. Simply remove the facepanel and then remove the screws
holding it in position. Replace the fader with a quality authorized replacement from your local Numark retailer.
10. “Slope Knob” (Input Fader Curve Style Control): The position of this knob determines the rate of volume level increase
of the fader. When turned to the left, the fader will gradually fade in the volume as it is engaged. When it is turned all the
way to the right, a very sharp fade of the volume will occur immediately when the fader is engaged.
11. “Reverse Button” (Input Fader Reverse Control): Activation of this switch can reverse the fader direction.
- The Leader in DJ Technology
©2002 Numark Industries
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PPD01
Cueing / Monitor Controls
12. “Program/PFL Level Meter and Button”: Press to alternate display modes.
a) When PROGRAM is indicated, this meter displays the stereo output levels of your mixed signal.
b) When CH1 CH2 is indicated the meter shows the peak, “PFL”, Pre Fader levels of channels 1 and 2. You can use
the channel “Gain” and “EQ” controls to match the levels of input signals while cueing
13. “Cue Gain Knob” (Headphone Level): This rotary control adjusts the levels of the headphones connected to the front
panel input.
14. “Cue Tone Knob” (Headphone Tone Control): This rotary knob adjusts the tone of the headphone output. The knob
can be raised and lowered to hide away by pressing it down.
15. “Channel Cue Slider”: Channels 1 and 2 can be previewed using this mini-crossfader. Sliding this to the left plays the
left channel-1 and sliding to the right plays the right channel-2.
16. “Cue Button” (MIC and MASTER Cue Buttons): When pressed, the CUE button illuminates green indicating that the
source is being cued to the headphones. When you press Mic PFL it adds it to the cue mix. When Master Cue is pressed
only the master output is heard.
17. “Headphone Jack” (Quarter Inch Output Terminal): Your headphones can be connected to this ¼” terminals. The
Volume should always be set at its lowest setting while connecting and disconnecting headphones to prevent damage to
headphones and/or your hearing.
Crossfader Controls
18. “Crossfader Slider” (Digital VCA Crossfader): This slide fader blends audio between CH-1 and CH-2. Its action can be
modified with the “Mode” , “Slope”, and “Direction” controls. This digital mixer uses digital VCA technology to accurately
determine slider position. Both the VCA and Digital technologies combined allow for some very powerful effects.
Note: This fader is user replaceable if it should ever wear out. Simply remove the facepanel and then remove the screws
holding it in position. Replace the fader with a quality authorized replacement from your local Numark retailer.
19. “MODE and MODE Display” (Crossfader Function Control and Display): This toggle switch changes crossfader modes
be left-right movement. The current mode is indicated in the mode display under the crossfader. These modes are
described in detail in the section entitled “CROSSFADER MODES”.
20. “Contour Knob” (Crossfader Rate/Slope Control): The position of this switch determines how quickly or intensely the
crossfader will act depending upon mode setting.
21. “Direction Button” (Crossfader Reverse Control): Activation of this switch reverses the assignment of CH-1 and CH-2
on the crossfader.
Output Controls
22. “Master Knob” (Main Output Level Control): This rotary control adjusts the main output volume.
23. “Booth Knob” (Master/Split Style Headphone Cueing Switch): This rotary control adjusts the auxiliary (AKA booth)
output volume.
- The Leader in DJ Technology
©2002 Numark Industries
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PPD01
REAR PANEL FEATURES
Note: It is recommended that the mixer be turned off before connecting and disconnecting any
sources to the inputs of the mixer.
1. “AUX-SESSION INPUT” (Auxiliary Input): The line level input is used to connect the output from an external mixers or
additional CD players and other line level devices such as samplers, tape decks, keyboards, and line output turntables. This
input is mixed with any connected microphone.
2. “Phono/AUX Inputs” (Turntable Input Connection): The Phono input is used for connecting your turntables or other
devices. Input source is determined by the PHONO/LINE switch on the rear panel.
3. “Phono/Line source switch”: This switch activates and deactivates the sensitive RIAA phono preamplifiers. Only
turntables with phono level output should be assigned when the switch is in the phono position. Some
turntables offer line level output. To use these turntables and other line devices like CD players, switch the input to Line.
4.
“GND” (Grounding Lug): This screw connector should be used to secure any devices connected to the mixer that need to
be grounded. Many turntables that are connected to the mixer will need to have a ground wire that is designed to connect
to the mixer’s chassis to eliminate hum and excessive noise.
5. “Line Inputs” (CD player, Tape Deck, Sampler Input Connection): The line level input is used to connect CD players
and other line level devices such as samplers, tape decks, keyboards, and line output turntables.
6. “Booth Output” (Auxiliary Stereo Unbalanced Output): This RCA output is for connecting a secondary external
monitoring device such as a booth monitor or second stereo output. The level of the booth output signal will increase as the
“Booth” volume control is increased.
7. “Master Unbalanced Output” (Main Stereo RCA Output): This RCA output is for connecting an external monitoring
device such as a PA system, powered monitors or a home stereo. The level of the master stereo output signal increases as
the “master” volume control is increased.
8. “Master Balance Output” (Balanced Quarter Inch Stereo Output): These ¼” outputs are for sending a balanced level
signal to a PA system or recording device. The level of the balanced output signal will also increase with the “master”
volume control. These outputs are durable, offer a better output signal, and are well suited for long cable runs.
9. “Digital Output” (Optical): 48kHz, 24-bit S/PDIF output. The format is type 2, form 1, also known as S/PDIF
(Sony/Phillips Digital Interface Format). This output can be connected to compatible devices such as CD Burners, Hard
Drive recorders, or other digital mixers. Higher audio fidelity is maintained from these outputs.
10. “Digital Output” (Coax): 48kHz, 24-bit S/PDIF output. The format is type 2, form 1, also known as S/PDIF (Sony/Phillips
Digital Interface Format). This output can be connected to compatible devices such as CD Burners, Hard Drive recorders, or
other digital mixers.
11. AC In: This mixer is designed to work with the power supply assembly that comes with the unit. While the power is
switched off, plug the power supply into the mixer first, then plug it into the outlet.
12. Power Switch: Use this switch to turn on the mixer after all input devices are already connected to prevent damage to
your equipment. Turn the mixer on before you turn on amplifiers and turn of amplifiers before you turn off the mixer
- The Leader in DJ Technology
©2002 Numark Industries
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PPD01
QUICK SETUP DIAGRAM
1. Study this setup diagram.
2. Make sure all faders are at “zero” and all devices are
off.
3. Connect all stereo input sources, your microphone,
and monitor headphones
4. Connect the stereo outputs to the power amplifier(s)
and/or audio sources.
6. Switch everything on in the following order.
• audio input sources (i.e. turntables or CD players)
• your mixer
• last, any amplifiers
7. When turning off, always reverse this operation by,
• turning off amplifiers
• your mixer
• last, any input devices
5. Plug your mixer and other devices into AC power.
- The Leader in DJ Technology
- 10 -
©2002 Numark Industries
Download from Www.Somanuals.com. All Manuals Search And Download.
PPD01
CROSSFADER MODES
This section describes the actions of your digital crossfader, depending upon mode settings.
Normal Fade: The contour knob controls the slope of crossfader. As a slope control, when the
contour is rotated to the left, the Crossfader will gradually fade from one channel to the other.
When rotated to the right, a very sharp fade between channels will occur immediately when the
fader is moved.
Velocity Sensitive Flanger: The velocity of the crossfader controls the amount of flanger
applied to the output. The contour knob controls the rate of the flanger.
Velocity Sensitive Band Pass Filter: The velocity of the crossfader controls the mix and
frequency of a Band-Pass filter applied to the output. The contour knob controls the slope of
crossfader.
Autopan: The current channel will be mixed in on either left or right only when the crossfader
is initially moved inwards. As the crossfader is moved to the center, the pan for the other
channel is re-balanced to the center. Every time the crossfader is brought inwards from an
endpoint, the mix will toggle between left and right. The contour knob controls the slope of
crossfader.
Auto-Cut: This crossfader creates a gating effect when the user moves the crossfader inwards
from an endpoint. The crossfader mode indicator will flash at the gating rate, which is controlled
by the contour knob. When the crossfader is moved towards the middle, it passes a threshold
which will stop the gating effect. The gating will not start again until the user returns to an
endpoint and moves inwards again.
Auto-Cut with Low Pass filter: This works similarly to “Autocut” except a LP filter is also
applied to the channel. The LP filter sweeps from 120 to 20kHz(full spectrum) as the crossfader
is moved towards the middle.
Dual Phase Shifter: The audio will be phase shifted when the fader is moved inwards from an
endpoint. The phase shifting will mix to dry as the xfader is moved to center. The contour
knob controls the slope of crossfader.
Vari-Cut: Using the contour knob, the user can position a brief audio cut in the crossfader. At
one extreme of the contour knob, both sides of the crossfader have a centered cut, making the
master audio output completely cut out in the center. At the other extreme, the cuts move
towards their respective endpoints. Different cut points will allow the user to double their
“crabbing” or “chirping” rate, or find a comfortable offset cut-in point.
- The Leader in DJ Technology
©2002 Numark Industries
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Professional Disc Jockey Products
LIMITED PRODUCT WARRANTY
1. What is covered and for how long? NUMARK INDUSTRIES LCC (“NUMARK”) warrants to the original purchaser that NUMARK'S DJ Mixers, Amplifiers, CD
players, turntables, preamplifiers, beatkeepers, equalizers, microphones, headphones, and all other accessories are free from defects in material and
workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer and continuing for the
following period of time after that date for (1) Year.
2. What is not covered? This Limited Warranty is conditioned upon proper use of the product by the purchaser.
This Limited Warranty does not cover: (a) defects or damage resulting from accident, misuse, abuse, neglect, unusual physical or electrical stress, modification
of any part of the product, or cosmetic damage; (b) equipment that has the serial number removed or made illegible; (c) all plastic surfaces and other externally
exposed parts that are scratched or damaged due to normal use; (d) defects or damage from improper testing, operation, maintenance, installation, adjustment,
or service of the mixers; (e) crossfaders.
3. What are NUMARK'S obligations? During the applicable warranty period, NUMARK will repair or replace, at NUMARK'S sole discretion, without charge to the
purchaser, any defective component part of the mixer. To obtain service under this Limited Warranty, purchaser must first contact NUMARK and obtain a return
authorization number (“RA#”). Purchaser must then return the mixer to NUMARK in an adequate container for shipping, accompanied by purchaser's sales
receipt or comparable proof of sale showing the date of purchase, the serial number of the product, and the seller's name and address. To obtain an RA# and
assistance on where to return the mixer, contact NUMARK customer service at 401-295 9000. Upon receipt, NUMARK will repair or replace the defective
products. NUMARK may, at NUMARK'S sole discretion, use rebuilt, reconditioned, or new parts or components when repairing any product or replace a
product with a rebuilt, reconditioned or new product. Repaired mixers will be warranted for a period equal to the remainder of the original Limited Warranty on
the original mixer or for (90) days, whichever is longer. All replaced parts, components, boards and equipment become the property of NUMARK. If NUMARK
determines that any mixer is not covered by this Limited Warranty, purchaser must pay all parts, shipping, and labor charges for the repair or return of such
mixer.
4. What are the limits on NUMARK'S liabilities? THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY, TOGETHER WITH ANY IMPLIED WARRANTIES
COVERING NUMARK MIXERS, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, NUMARK
SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO
PURCHASER'S PROPERTY, OR INJURY TO PURCHASER OR OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE ANY NUMARK
MIXER, BREACH OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT NOT LIMITED TO NUMARK'S OWN NEGLIGENCE, EVEN IF NUMARK OR ITS
AGENT HAS BEEN ADVISED OF SUCH DAMAGES, OR FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY OTHER PARTY. THIS LIMITED
WARRANTY IS THE COMPLETE WARRANTY FOR NUMARK'S MIXERS, AND IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THIS
LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER'S
EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL
ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH
PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS.
This Limited Warranty allocates risk of product failure between purchaser and NUMARK, and NUMARK'S product pricing reflects this allocation of risk and the
limitations of liability contained in this Limited Warranty. The agents, employees, distributors, and dealers of NUMARK are not authorized to make modifications
to this Limited Warranty, or make additional warranties binding on NUMARK. Accordingly, additional statements such as dealer advertising or presentation,
whether oral or written, do not constitute warranties by NUMARK and should not be relied upon.
5. How does state law apply to this warranty? SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES OR HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER.
6. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary from one jurisdiction to another.
RETURN INFORMATION
•
•
•
•
A Return Authorization number must be obtained from Numark through the address or phone numbers below.
A copy of the original sales receipt must also be included for the equipment to be repaired under warranty.
The faulty equipment must be packed in its original packaging.
One additional outer layer of packaging must be included to ensure product safety. Failures to do so may inadequately protect the equipment in transit
and, therefore, jeopardize the customer’s warranty.
•
•
Numark will not accept COD shipments and no call tags will be issued for merchandise return.
Numark will not return repaired merchandise to customers by priority service, unless by written request at the customer’s cost. Requests must be
submitted in writing with merchandise returned.
•
The defective Numark equipment should be sent, FREIGHT PREPAID with Return Authorization number clearly printed on the outer packaging and
original sales receipt enclosed to:
INDUSTRIES
Attention: Service Department
11 Helmsman Avenue
Phone: +1 (401) 295-9000
Fax:
+1 (401) 295-5200
Web:
North Kingstown, RI 02852 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|