Explorer 657
Fishfinder and Chartplotter
Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Important
The choice, location, angle and installation Sonar fishfinder: The accuracy of the sonar
of the instrument & transducers are critical to
performance of the system as intended. Follow
instructions in this manual carefully. If in doubt,
consult your Northstar dealer.
depth display can be limited by many factors,
including the type of the transducers, the location
of the transducers and water conditions. It is the
user’s responsibility to ensure the 657 transducers
are installed and used correctly.
Ensure that any holes cut are in a safe position and
will not weaken the boat’s structure. If in doubt,
consult a qualified boat builder.
AIS: The AIS features on this chart-plotter are
designed as a safety aid only and do not guarantee
safety at sea. AIS transmission is mandatory on
some, but not all, vessels. You should check your
local laws and regulations for requirements in your
area. As a result of different legal requirements,
different vessel sizes and uses, you should not
assume that your AIS equipped chart-plotter will
show the location of ALL vessels in your area.
Careful prudence, judgement, and safe navigation
practices should always be exercised. AIS should
be used to complement radar, but AIS is not a
substitute for radar.
Do not install plastic through hull transducers in
solid wooden hulls. Leaking through the hull may
result.
Do not install bronze transducers in metal hulls.
This will cause electrolytic corrosion that may
result in damage to the hull or transducer.
Sonar Performance: The accuracy of the sonar
depth display can be affected by many factors,
including the type and location of the transducer
and water conditions. Ensure that the transducer is
located and used correctly.
Fuel Computer: Fuel economy can alter
drastically depending on the boat loading and sea
conditions. The fuel computer should not be the
sole source of information concerning available
fuel onboard and the electronic information
should be supplemented by visual or other checks
of the fuel load. This is necessary due to possible
operator induced errors such as forgetting to
reset the fuel used when filling the tank, running
the engine with the fuel computer not switched
on or other operator controlled actions that may
render the device inaccurate. Always ensure that
adequate fuel is carried onboard for the intended
trip plus a reserve to allow for unforeseen
circumstances.
Global Positioning System: The Global
Positioning System (GPS) is operated by the
US Government which is solely responsible for
its operation, accuracy and maintenance. The
GPS system is subject to changes which could
affect the accuracy and performance of all GPS
equipment anywhere in the world including
the 657. Whilst the Northstar 657 is a precision
navigation instrument, it can be misused or
misinterpreted, which can result in its use
being unsafe. To reduce the risk of misusing or
misinterpreting the 657, the user must read and
understand all aspects of this Installation and
Operation manual. We also suggest that the user
practice all operations using the built in simulator
before using the 657 at sea.
Failure to adhere to these warnings may
lead to death, serious injury or property
damage. Northstar disclaims all liability for
installation or use of this product that causes
or contributes to death, injury or property
damage or that violates any law.
Electronic Chart: The electronic chart used by
the 657 is an aid to navigation and is designed to
supplement the use of official government charts
not replace them. Only official government charts
supplemented by notices to mariners contain
the information required for safe and prudent
navigation. Always supplement the information
provided by the 657 with other plotting sources
such as observations, depth soundings, radar and
hand compass bearings. Should the information
not agree then the discrepancy must be resolved
before proceeding any further.
The 657 is set up with default units of feet, °F
(Fahrenheit), US gallons and knots. To change the
units, see section 17-10.
Northstar Explorer 657 Installation and Operation Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1 Introduction ......................................................................................................................................... 7
1-1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1-2 Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1-3 Plug-in cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1-4 Removing and replacing the display unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 Basic Operation.................................................................................................................................... 10
2-1 Using the keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2-2 Turning on and off / auto power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2-3 Backlight and night mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2-4 Man overboard (MOB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2-5 Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2-6 Simulate mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2-7 The main windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3 Navigation: Chart................................................................................................................................. 19
3-1 Introduction to navigating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3-2 Chart window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3-3 Distance and bearing calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3-4 Projected course . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3-5 Tracks and tracking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4 Navigation: Highway window .............................................................................................................. 24
5 Navigation: Waypoints......................................................................................................................... 25
5-1 Waypoints window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
5-2 Managing waypoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
6 Navigation: Routes .............................................................................................................................. 27
6-1 Routes window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
6-2 Managing routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
7 Satellites ............................................................................................................................................. 30
7-1 Satellite window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8 Sonar fishfinding: Introduction ........................................................................................................... 31
8-1 Using the 657. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8-2 Interpreting the display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8-3 Single and Dual frequency fishfinding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
4
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-4 Fish detection and display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8-5 Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
8-6 Gain and threshold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
9 Sonar fishfinding: Displays .................................................................................................................. 40
9-1 Sonar history display - no split . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
9-2 Sonar Zoom and Full Screen Zoom displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
9-3 Sonar Bottom display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
9-4 Sonar 50/200 display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
9-5 Sonar A-Scope display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
10 Gauges window.................................................................................................................................. 44
11 Data window...................................................................................................................................... 44
12 Fuel functions and display.................................................................................................................. 45
12-1 What the fuel computer does. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
12-2 Fuel window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
12-3 When you add or remove fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
12-4 Low fuel alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
12-5 Boat speed sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
12-6 Fuel consumption curves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
12-7 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
13 Tides window ..................................................................................................................................... 52
14 User card window............................................................................................................................... 53
15 AIS ..................................................................................................................................................... 54
15-1 Viewing AIS Vessels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
15-2 Dangerous Vessels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
15-3 AIS Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
16 DSC/Buddy track windows .................................................................................................................. 57
16-1 The displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
16-2 Using the displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
17 Setting up the 657.............................................................................................................................. 59
17-1 Setup > System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
17-2 Setup > Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
17-3 Setup > Sonar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
17-4 Setup > GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Northstar Explorer 657 Installation and Operation Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
17-5 Setup > Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
17-6 Setup > Track. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
17-7 Setup > AIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
17-8 Setup > Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
17-9 Setup > Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
17-10 Setup > Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
17-11 Setup > Comms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
17-12 Setup > Calibrate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
17-13 Setup > Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
17-14 Setup > Favorites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
17-15 Setup > Simulate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
18 Installation ....................................................................................................................................... 74
18-1 Installation: What comes with the 657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
18-2 Installation: Options and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
18-3 Installation: The display unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
18-4 Installation: Power/data cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
18-5 Installation: GPS antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
18-6 Installation: Sonar transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
18-7 Installation: Northstar petrol/gasoline sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
18-8 Installation: SmartCraft™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
18-9 Installation: Other NavBus instruments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
18-10 Installation: Other NMEA instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
18-11 Installation: Setup and test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Appendix A - Specifications..................................................................................................................... 84
Appendix B - Troubleshooting................................................................................................................. 86
B-1 General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
B-2 GPS navigation problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
B-3 Fuel consumption problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
B-4 Sonar fishfinding problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Appendix C - Glossary and navigation data.............................................................................................. 90
6
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Introduction
Quick reference to the built-in and optional features:
Feature
General
Type
See
Requires
How to use the keys and displays
2
Troubleshooting
Appendix B
Simulate mode
2-6
Glossary of special names
Specifications
Appendix C
Appendix A
2-4
MOB
Man overboard key
Navigation
Overview of how to navigate
Finding the boat’s position on the chart
Navigate to any point or to a waypoint
Navigate along a route
3-1
GPS fix
3-2
3-1
3-1
Projected course: An estimate of progress
Tracks: records of where the boat has been
GPS receiver status
3-4
3-5
7
Saving and loading data with a user card
Chart features (built in world chart)
Chart details
14
User card
Chart data
3-2
3-2-4 & 5
11
C-MAP™ chart
C-MAP™ chart
Tides at a port
AIS
15
Alarms
Built in alarms
2-5
SmartCraft™ engine alarms
Data at top of main displays
Compass at top of main displays
Dedicated data window
1-1
SmartCraft™
Boat data
2-7-3
2-7-4
11
Fuel
Fuel computer, petrol/gasoline engine
Fuel computer, SmartCraft™ engines
What to do when you add or remove fuel
12
Fuel sensors
SmartCraft™
12
12-1
Sounder
Overview of the depth sounder
Depth, bottom features, water features
Fishfinder
8
8
8
Sounder
Sounder
Sounder
Other boats
Track your buddy, polling other boats
Distress calls
16
16
DSC VHF
DSC VHF
Northstar Explorer 657 Installation and Operation Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1-1 Overview
The Northstar 657 is a compact, rugged, highly
integrated marine chartplotter and fishfinder. It is
easy to use and has an easy to read color display.
Complex functions can be performed with a few
key presses, taking the hard work out of boating.
DSC/Buddy track functions require a
Northstar DSC VHF radio with Buddy track
support to be installed.
The 657 can send data to other instruments,
such as an autopilot, and receive data from
other instruments.
The available functions, displays and setup
menus depend on the optional sensors and
instruments that are installed:
AIS functions require an optional AIS receiver
to be installed.
Sonar functions require a sonar transducer to
be installed
For information on installing options, see section
18-2.
Fuel functions require one or more
petrol/gasoline or diesel fuel sensors to be
installed.
This manual describes how to install and operate
the 657. Special terms are explained in Appendix
C. For maximum benefit, please read this manual
carefully before installing and using the unit. For
more information on this instrument and other
Northstar products, go to our website,
SmartCraft™ engine functions require a
SmartCraft™ system to be installed. For
information on using SmartCraft™, see the
SmartCraft™ Gateway Installation and
Operation Manual.
1-2 Cleaning and maintenance
The 657 screen is covered by a proprietary
anti-reflection coating. To avoid damage, clean
the screen only with a damp cloth and mild
detergent when dirty or covered in sea salt.
Avoid abrasive cleaners, petrol or other solvents.
If a plug-in card gets dirty or wet, clean it with a
damp cloth or mild detergent.
use only one coat of paint. Remove the previous
coat of antifouling paint by sanding it lightly.
To optimize performance, avoid walking on
or jamming cables and connectors. Keep the
transducer free of weed, paint and debris. Do not
use a high pressure water blast on a speed sensor
paddlewheel as it may damage the bearings.
Cover or remove a transom-mounted transducer
when repainting the hull. If painting over a
through hull transducer with antifouling paint,
Push the dust cover over the display when the
657 is turned off.
1-3 Plug-in cards
2
C-MAP™ user cards are used to store
navigation data. Each user card expands
the 657 memory and allows the data to be
transferred to another 657 easily.
(see section 14).
The 657 can use two kinds of plug-in card:
1
C-MAP™ chart cards have chart details
required for navigating in a particular region.
When a chart card is plugged in, the extra
details automatically appear on the 657 chart
window.
Note: The older 5 volt user cards are not
supported.
The 657 can use NT, NT+ and NT-MAX
cards. NT-MAX cards have much more chart
information than earlier cards, including
photos of points of interest.
8
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the plug-in card
Gold contacts under here
1
2
4
3
Card
Holder
Turn the 657 off (see section 2-2).
CAUTION
Handle plug-in cards carefully. Keep them in
their protective cases when not plugged into
the 657.
Pull the card holder out of the 657 and pull any
card out of holder.
Put the card in its case.
Push new card into holder. Ensure the gold
contacts are on the outer edge and underneath
(see above).
Keep the holder in place in the 657 at all times
to prevent moisture from entering the card
compartment.
Keep the card’s case.
Push card holder fully into 657
1-4 Removing and replacing the display unit
If the display unit is bracket mounted then the
display unit can easily be removed and replaced
for security or protection.
Insert each connector and turn the
locking collar clockwise until it is finger
tight.
Removing the display unit:
Nothing will be damaged if a cable is
plugged into the wrong socket by mistake.
1
2
3
Turn the display unit off (see section 2-2) and
put the dust cover on.
2
Hold the display unit in place on the
mounting bracket. Adjust the tilt of the
display for best viewing, then hand tighten
the knob on the mounting bracket. Remove
the dust cover.
Loosen the knob on the mounting bracket
and lift the unit off the bracket.
Unplug the connectors from the display unit;
turning each locking collar anticlockwise until
you can pull the plug out.
4
5
Push the attached dust covers over the
exposed ends of the connectors.
Store the display unit in a dry clean place,
such as the optional Northstar carry bag.
Replacing the display unit
1
Remove the dust covers from the connectors.
Plug the connectors into the back of the
display unit:
Mounting
bracket
Match the connector’s color to the socket
color.
Knob
Northstar Explorer 657 Installation and Operation Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Basic Operation
Overview of the keys
ESCAPE - Go back to an earlier menu or display. In chart mode,
centres chart at boat’s position.
DISPLAY - Show a menu of the main displays. To go to a display,
select it from the menu (see section 2-7).
CURSOR KEYS - to move the cursor or the selection highlight.
MENU - Show a menu of the options for the current window.
again to display the Setup menu (see section 17).
Press
ENTER - Start an action or accept a change.
ZOOM - Chart window: Zoom in or out to display different
areas and detail on the chart.
Sonar window: Change the depth range displayed.
FAVORITES - Allows you to quickly switch between your saved
favorite displays.
MOB - (Man Overboard, see section 2-4).
POWER - Turn 657 on and off (see section 2-2); adjust the backlighting
(see section 2-3).
2-1 Using the keys
In this manual:
Selecting a submenu
Press means to push the key for less than a
A
after a menu item indicates a submenu, for
second.
example Chart . Press or to move the
highlight to the submenu, then press
.
Hold means to hold the key down.
Starting a command
The internal beeper beeps when a key is pressed
(to disable or enable the beep, see section 17-1).
Press
or
to move the highlight to the
command, for example Goto cursor, then press
.
Using the menus
Operate the 657 by selecting items from menus.
Items can be submenus, commands or data.
10
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing data
First press or
data to change, then:
a) To change a tick box
means On or Yes
c) To change a name or number:
to move the highlight to the
1
2
Press
to display the name or number:
Press
or
to select a letter or digit to
change. Press
digit.
or
to change the letter or
Repeat this to change other letters or
numbers.
means Off or No.
Press
or
to change the tick box.
3
Press
to accept the new value. Or press
to ignore the changes.
b) To select an option
1
2
Press
to display the menu of options.
d ) To change a slider value
Press to decrease the value or
the value.
to increase
Press
or
to move the highlight to the
option you want, then press
.
2-2 Turning on and off / auto power
Turning on manually
If the 657 is not wired for auto power, press
Auto power
If the 657 is wired for auto power (see section
to
turn the unit on. If necessary, adjust the display to
be easy to read (see section 2-3).
18-4), then:
•
•
•
The 657 automatically turns on when you turn
the boat’s ignition switch on.
Note: If the 657 is not wired for auto power then
the 657 does not record engine hours and might
not record fuel consumption (see section 18-4).
You can not turn the 657 off while the
ignition switch is on.
If Auto power off (see section 17-1) is , the
657 automatically turns off when you turn the
boat’s ignition switch off.
Turning off manually
If the 657 is not wired for auto power or if the
ignition switch is off, hold down
display turns off.
until the
•
If Auto power off (see section 17-1) is
, the 657 stays on when you turn the boat’s
ignition switch off. You can now turn the 657
off manually.
Northstar Explorer 657 Installation and Operation Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2-3 Backlight and night mode
Night mode
To go to the Backlight display, press
briefly.
Night mode sets the palette for all displays.
Backlight
Normal palette, for daytime
The display and keys are backlit. To change the
backlight level, highlight select Backlight, then
A palette optimised for night time.
To change mode, highlight Night mode, then
press
to dim or
to brighten.
press
or
. To change only the chart
When you have finished, press
palette, see section 17-2.
Tip: Press
twice to give the brightest
screen, with maximum backlight and Night mode
off.
2-4 Man overboard (MOB)
The MOB feature saves the boat’s position and
then navigates back to this point.
If the NMEA output (autopilot) is on, the
657 asks if the autopilot is active.
Select:
!
WARNING
No: Use the 657 to manually navigate to the
destination MOB waypoint (see sections
3-1-1 and 3-1-2).
MOB will not work if the 657 does not have
a GPS fix.
Yes: The 657 asks if the boat is to go to the
MOB waypoint.
1
2
Press
.
Select:
The 657 stores the boat’s position as a
waypoint called MOB.
Yes: to immediately start navigating to
the MOB waypoint.
The 657 changes to the chart window, with
the MOB waypoint at the center of the chart.
!
WARNING
The chart zooms in for accurate navigation.
If the chart can not show the required small
scale, the 657 changes to plotter mode (a
white display with crosshatching and no
chart details, see section 17-2).
This might result in a sudden and dangerous
turn.
No: disengage the autopilot; then use
the 657 to manually navigate to the
destination MOB waypoint (see sections
3-1-1 and 3-1-2).
3
The 657 sets the MOB waypoint to be the
destination to navigate to.
If the NMEA output (autopilot) is off
(see section 17-11) use the 657 to manually
navigate to the destination MOB waypoint
(see sections 3-1-1 and 3-1-2).
To cancel MOB or set another MOB
1
2
Press
again to display a menu.
Select an option from the menu.
Tip: The MOB waypoint remains on the chart
after the MOB has been cancelled. To delete the
MOB waypoint, see section 5-2-5.
12
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-5 Alarms
When the 657 detects an alarm condition, it
displays a warning message on the display, the
internal beeper sounds and any external beepers
or lights operate.
Press
to clear the alarm. The alarm will
sound again if the alarm condition occurs again.
The 657 has user settable alarms (see section
17-9).
2-6 Simulate mode
In Simulate mode, the 657 ignores data from the
GPS antenna and other transducers and sensors
and the 657 generates this data itself. Otherwise,
the 657 functions normally.
There are two simulate modes:
•
Normal: Allows a user to become familiar with
the 657 off the water.
•
Demo: Simulates a boat moving along a
route and automatically displays different 657
functions.
To start and stop Simulate mode, and for more
information, see section 17-15. In simulate mode,
Simulate or Demo flashes at the bottom of the
display.
!
WARNING
Never have Simulate mode on when the 657
is navigating on the water.
Northstar Explorer 657 Installation and Operation Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2-7 The main windows
The display menu allows quick access to the main
windows. Full-screen Chart and Sonar are at the
top of the menu. Other windows are available
from the More…sub menu.
Note
1
The windows available depend
on the optional sensors and
instruments that are installed
(see section 1-1).
2
Set up commonly used windows
as favorites and press
to
switch between windows (see
section 2-7-2).
14
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The windows below the menu divider can
only be shown full screen without a data header.
(see section 2-7-3).
Northstar Explorer 657 Installation and Operation Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2-7-1 Multi window displays
The 657 can show two windows at once.
Changing window size
1
2
Press
and select Split ratio.
to change the height of the
Press
or
windows.
Note: Some windows are fixed in size.
3
Press
.
Exchanging two windows on the display
1
Press
twice to change the active
window.
2
Press
second window.
, select Replaceand select the
The 657 exchanges the two windows.
Replacing a window on the display
1
Press
twice to change the active
window.
2
Press
, select Replaceand select a
Adding a window to the display
new window that is not currently visible.
Note:
Press
, select Add windowand select a
window to add. The 657 automatically rearranges
the display to show the new window.
When some windows are small then not all the
data is shown.
The active window
If there is more than one window displayed, the
active window is indicated by a red border. Press
twice to change the active window.
Pressing
the active window.
will display the options menu for
Chart is active
Red border
Sonar is active
Red border
16
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-7-2 Favorite displays
The 657 has a list of commonly used displays,
called favorite displays. There can be up to six
favorite displays.
Deleting a favorite display from the list
1
Press
twice then select
Favorites.
Highlight the display to delete, press
Sonar, Gauges, Fuel, Data, and Tanks windows can
be combined in a display. Each of these displays
can have a data header (see section 2-7-3) and a
compass (see section 2-7-4).
2
and select Delete.
Selecting a favorite display
To select another favourite, press
one or
more times. For example, with six favourites:
Changing the order of the favorites list
Adding a favorite display to the list
1
Press
twice then select
1
Set up the display with the window or
windows you want in the new favorite (see
section 2-7).
Favorites.
Highlight the display to move, press
2
and select Move upor Move down.
2
3
Press
and select Save this
display. The 657 displays the favorites list.
Select where in the list to add the new
favorite. If you select an existing favorite
display then the new favorite will replace the
existing favorite in the list.
Northstar Explorer 657 Installation and Operation Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Favorites displays and data headers
2-7-3 Data header
To set a data header for a favorites display, follow
the steps to add a favorite (see section 2-7-2
- Adding a favorite display to the list). In step 1,
set the data header for the favorite as described
above.
The displays can show data at the top, called the
data header.
2-7-4 Compass
The chart, sonar and highway displays can show a
compass at the top of the window.
When you select a window from the display
menu (see section 2-7) the 657 displays an
appropriate data header for the window.
The compass always shows the boat’s course
over ground (COG), a black symbol in the middle.
When the boat is navigating to a point, the
compass also shows bearing to the destination
(BRG), a red symbol.
Each favorite display (see section 2-7-2) has
its own data header. When you press
to recall a favorite display, the 657 recalls the
favorite displays data header.
In this example, BRG is 332°M and COG is 341°M.
To turn the compass off or on:
Setting the data header for a display
1
2
Press
To turn the data header on or off:
Select Data.
ii Select or
To select the size of the data:
Select Size.
and select Data header.
1
2
Press
and select Data header.
Set Compass to or
.
i
.
3
i
ii Select the size to display.
To change the data displayed:
Select Data setup.
4
i
ii Change a data field:
a
Press the cursor keys to highlight the
field.
b
c
Press
data items.
to display a menu of
Select a data item that is available
on your system or select None to
leave the field empty.
iii Repeat the above step to set the other
data fields.
Tip: If all fields in a line are None then the line
will not be displayed and the data header will
take less space on the display.
5
Press
.
Tip: The data header will change when you
select another display. To set a data header that
you can recall later, set the header as part of a
favorites display (see below).
18
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Navigation: Chart
The chart window shows the chart, the boat’s
position course and navigation data.
3-1 Introduction to navigating
The 657 has two ways of navigating, going straight
to a point or following a route.
3-1-2 Going to a waypoint or to a point on
the chart
A waypoint is a position that you can set on the
657 chart, for example a fishing spot or a point on
a route (see section 5).
3-1-1 Navigating to a point
When the 657 is navigating to a point, the chart
and highway displays show navigation data:
Going to a waypoint from the chart window
A
B
The boat position
.
1
2
Go to the chart window.
The destination point marked with a circle.
The boat’s plotted course to the destination.
Move the cursor to the waypoint:
either use the cursor keys or use Find(see
section 3-2-5).
C
D
Two CDI lines, parallel to the boat’s plotted
course, which indicate the maximum
3
Press
and select Goto.
expected deviation from the plotted course.
Going to a waypoint from the waypoints
window
B
D
1
2
Go to the waypoints window.
C
Press
goto.
or
to highlight the waypoint to
3
Press
and select Goto.
A
D
Going to a point on the chart
1
2
Switch to a chart window.
Move the cursor to the destination point:
either use the cursor keys or use Find(see
section 3-2-5).
For more information, see appendix C.
If the 657 is connected to an autopilot, the 657 will
send data to the autopilot to steer the boat to the
destination. Start the autopilot before starting to
navigate to the point.
!
WARNING
Make sure the course does not pass over land
or dangerous waters.
If the 657 has no autopilot, steer the boat
manually:
a
b
c
use the boat position and destination on the
chart or highway displays
3
Press
and select Goto cursor.
Navigating
or use navigation data displayed on the data
header (see section 2-7-3)
The 657 navigates to the point as described in
section 3-1-1.
or use COG and BRG on the compass (see
section 2-7-4).
Cancelling navigating
Go to a Chart window, press
Cancel goto.
Tip: Before starting, create waypoints at points
of interest. Create a waypoint at the start of the
trip for you to navigate back to (see section 5-2-1).
and select
Note:
1
If the XTE alarm is enabled, an alarm will
sound if the boat deviates too much from its
intended course (see section 17-9).
2
If the arrival radius alarm is enabled, then an
alarm will sound to show that the boat has
reached the destination (see section 17-9).
Northstar Explorer 657 Installation and Operation Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3-1-3 Following a route
Skipping a waypoint
Preparing
To skip a waypoint, go to a chart window,
A route is a list of waypoints that the boat can
follow (see section 6).
press
and select Skip. The 657 starts
navigating straight towards the next waypoint
on the route.
To create waypoints before creating the
route, see section 5-2-1.
To create a route, see section 6-2-1.
!
WARNING
Starting a route from the chart window:
Skipping a waypoint with the autopilot on
might result in a sudden course change.
1
2
3
Go to the chart window.
Press
and select Start Route
to highlight the route to
.
Press
or
Cancelling a route
follow. Press
When the boat has reached the final waypoint, or
to stop the boat following the route at any time,
cancel the route. Go to a chart window, press
and select Cancel route.
4
The 657 asks for the direction to traverse the
route.
Select Forward(the order the route was
created) or Reverse.
5
The 657 displays the chart with the route
marked and starts navigating from the start
of the route.
Starting a route from the routes window:
1
2
Go to the routes window.
Then follow step 3 as in starting a route
from the chart window above.
Navigating
The 657 navigates to each waypoint on the route
in turn as described in section 3-1-1.
The 657 stops navigating to the waypoint at the
end of the current leg and starts the next leg of
the route:
a
when the boat comes within 0.025 nm of the
waypoint
b
c
or when the boat passes the waypoint
or if you skip the waypoint.
20
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2 Chart window
To go to the Chart window, press
then
select Chart.
A typical chart window shows:
A
B
C
F
H
D
E
I
J
K
G
A
B
C
D
E
F
G
H
I
Data header. To turn the data off or on or to change what data is displayed, see section 2-7-3
Compass (see section 2-7-4)
Chart scale (see section 3-2-3)
Boat position (see section 3-2-1)
Boat track (see section 3-5)
Boat course and CDI lines (see Appendix C, CDI).
Distance and bearing of cursor from boat
Land
Sea
J
The cursor (see section 3-2-1)
A typical waypoint (see section 5)
K
Note: To change the types of information displayed on the chart, see section 17-2. To change to a
perspective view of the chart, see section 3-2-6.
Northstar Explorer 657 Installation and Operation Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2-1 Chart modes
The Chart has two modes:
!
WARNING
When reading the boat position, make sure
the position is not the cursor position.
Center on boat mode
To switch to center on boat mode in the chart
window, press
. The boat is at the center
of the chart. As the boat moves through the
water, the chart automatically scrolls to keep the
boat in the center of the chart. The cursor (see
below) is turned off.
3-2-3 Chart scale
Press
to zoom in and display a smaller area of
the chart in more detail. Press
and display a bigger area in less detail.
to zoom out
Cursor mode
The chart scale is displayed at the top left of the
chart:
The keys
and
are called cursor keys.
To switch to cursor mode in the chart window,
hold down a cursor key. The cursor
and moves away from the boat:
appears
3-2-4 Chart symbols and information
The chart shows many kinds of symbols, such as
waypoints, ports, marinas, buoys and beacons. If
Press the key which points in the direction
that the cursor will move, for example press
to move the cursor down.
necessary, press or
scale where the symbol is displayed.
or
to choose a chart
Press midway between two of the cursor keys
to make the cursor move diagonally.
To see stored information about a symbol:
Hold a cursor key down to make the cursor
move continuously across the display.
1
Either move the cursor to the symbol on the
chart and wait two seconds
In Cursor mode:
or use Find to move the cursor to a symbol
for a port or service (see section 3-2-5).
The distance ( DST) and bearing ( BRG) of
the cursor from the boat are displayed at the
bottom corner of the display.
2
3
A window appears at the bottom of the
display with some information about the
symbol.
The chart does not scroll as the boat moves.
If the cursor reaches the edge of the display,
the chart will scroll.
To see more detail about a symbol or a list of
associated items for the symbol, press
:
For example, hold down
to move the
i
Select an item to display. If there are more
items than will fit on the display, press
cursor to the right side of the display and the
chart will scroll to the left.
or
to scroll up or down.
3-2-2 Latitude and longitude
Select a camera icon to display a photo
of the item. If the photo is too big to fit
Latitude and longitude can be displayed in
the data header. The display is degrees and
minutes to three decimal places, about 2 m (6
ft) resolution. Normally the position is the boat’s
position, and the latitude and longitude has a
boat symbol to show this:
on the display, press
scroll the photo.
,
,
or
to
Select Tide Stationto display a tide
chart for the position (see section 13).
ii Select other items or press
return to the chart.
to
36° 29.637’ N or S
Latitude
175° 09.165’ E or W Longitude
To see stored information about nearby symbols
press
and select Chart info. Then
follow step 3 above.
If the cursor has been moved in the last ten
seconds, then the position is the cursor’s position,
and the latitude and longitude has a cursor
symbol to show this:
36° 29.841’ N or S
Latitude
175° 09.012’ E or W Longitude
22
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
For Ports by name: to search for a different
3-2-5 Finding a chart symbol
To find and display a chart symbol:
port name, press
. change the name,
then press
.
1
2
Press
and select Find.
5
Select the item and press . The chart
window changes to show the item in the
middle of the display.
Select the type of symbol: Waypoints, Routes,
Ports by name, Ports & services, Tide stations
or AIS Vessels.
To see stored information about the item,
3
For Ports & services: select the type of service
to find.
press
(see section 3-2-4).
3-2-6 Perspective view
Perspective view shows the chart from an
angle instead of from straight above. To turn
perspective view on or off, press
Perspectiveto or
For Ports by name: press
enter a name or letters contained in the port
name, then press
,
,
or
to
.
and set
4
A list of items is displayed. If there are more
items than will fit on the display, press
to page up and down.
.
or
3-3 Distance and bearing calculator
The distance and bearing calculator can plot
a course of one or several legs and show the
bearing and length of each leg, as well as the
total distance along the course. The completed
course can be converted into a route.
4
5
6
To remove the last leg from the course, press
and select Remove.
Repeat the above two steps to enter the
whole course.
To save the new course as a route, press
and select Save. This also saves any
To use the distance and bearing calculator:
1
Select the Chart window. Press
and
new points on the course as new waypoints,
with default names. If necessary, edit the
route later (see section 6-2-2) and edit any
new waypoints later (see section 5-2-3).
select Distance.
Move the cursor to the start of the first leg. It
does not matter if this point is a waypoint or
2
not. Press
.
7
Finally, press
window.
to return to the chart
3
To add a leg to the course, move the cursor
to the end of the leg. It does not matter if this
point is a waypoint or not. The display shows
the bearing and length of the leg, as well
as the total distance along the course. Press
.
3-4 Projected course
If Projected course is turned on, then the 657
will display the projected position based on the
course over ground (COG), speed and a specified
time. To turn Projected course on and off and to
set the time, see section 17-2.
A
B
C
A
B
C
Projected position
Boat’s projected course
Boat position
Northstar Explorer 657 Installation and Operation Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3-5 Tracks and tracking
Tracking records the boat’s position to memory at
regular intervals, which can be:
the harbour. Record reference tracks in good
conditions.
Time intervals.
When recording is on and the track becomes full
then recording continues and the oldest points
in the track are deleted. The maximum length of
a track depends on the selected track interval: a
small interval will give a shorter, more detailed
track and a long interval will give a longer, less
detailed track, as shown in these examples:
Time intervals
Or distance intervals.
The track of where the boat has been can be
displayed on the chart. The 657 can display one
track while recording another.
To work with tracks, see section 17-6.
The 657 can store five tracks:
Interval
1 sec
Track 1
Track 2, 3, 4 or 5
minutes
1.4 hours
hours
Track 1 can hold up to 2000 points and is
intended to record the normal progress of
the boat.
33 minutes
5.5 hours
33 hours
8
10 sec
1 min
Distance intervals
Tracks 2, 3, 4 and 5 can hold up to 500 points
each and are intended to record sections to
be retraced accurately, for example entering a
river mouth.
8
Interval
Track 1
Track 2, 3, 4 or 5
0.01
1
20
2,000
5
500
Tip: Record a reference tracks and then use
the track to help navigate the same trip later.
For example, record a reference track as you
leave harbour. Then if you return to harbour and
visibility is poor, select the chart and navigate
manually along the reference track back into
10
20,000
5,000
The track lengths are in the current distance units,
for example nm.
4 Navigation: Highway window
The highway window has a bird’s eye view of the
boat’s course to a destination:
A
B
To go to the highway window, press
,
C
select More, then select Highway.
The highway window shows:
A
Optional data header (see section 2-7-3)
B
C
D
E
Optional compass (see section 2-7-4)
Destination waypoint
D
Boat’s plotted course to destination
CDI lines, parallel to the boat’s plotted course
(see Appendix C, CDI). The CDI lines are like a
highway over the water where the boat will
move.
E
F
F
CDI scale
G
The boat position is at the bottom, center of
the display.
G
!
WARNING
The highway window does not show land,
dangerous waters or chart symbols.
24
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Navigation: Waypoints
A waypoint is a position that you can set on the
657 chart, for example a fishing spot or a point on
a route. The 657 can have up to 3000 waypoints.
A waypoint can be created, changed or deleted.
A type:
Normal: A normal waypoint can be
navigated to or included in a route.
Danger: A danger waypoint is a point
to avoid. If the boat comes within the
danger radius of a danger waypoint the
unit can sound an alarm. (see section
17-9).
A waypoint has:
A name (up to eight characters).
An icon showing what kind of waypoint it is.
The available icons are:
A display option:
Controls how the waypoint is displayed
when the Waypointssetup option is set to
Selected(see section 17-2):
Off:The waypoint is not displayed.
Icon: The waypoint icon is displayed.
I+N (Icon and Name): The waypoint
icon and name are displayed.
If there are many waypoints, use this feature
to select which waypoints are displayed on
the chart.
Note: The other choices for Waypoints are Hide
all and Show all (see section 16-2).
A position.
A color for the waypoint symbol and name
on the chart.
5-1 Waypoints window
To go to the waypoints window, press
,
select More, then select Waypoints.
The waypoints window is a list of the waypoints
that have been entered, each with waypoint
symbol, name, latitude and longitude, distance
and bearing from the boat, type and display
option.
If there are more waypoints than will fit on the
display, press
or
to scroll up or down a
page at a time.
Northstar Explorer 657 Installation and Operation Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2 Managing waypoints
2
3
When the waypoint data is displayed, press
.
!
WARNING
Change the waypoint data
(see section 5-2-7).
Do not create a navigation waypoint on land
or in dangerous water.
5-2-1 Creating a new waypoint
Creating and editing a new waypoint from
the chart window
1
To create a waypoint at the boat position,
press
to switch the chart to center on
boat mode.
Or, to create a waypoint at a different point,
move the cursor to that point on the chart.
2
3
Press
.
A new waypoint, with the default name and
data is created.
Editing a waypoint from the waypoints
window
4
Change the waypoint data if necessary (see
section 5-2-7).
1
In the waypoints window, press
or
to
Creating a new waypoint from the waypoints
window
highlight the waypoint to edit. Press
and select Edit.
Change the waypoint data (see section 5-2-7).
1
2
3
In the waypoints window, press
and
2
select Create.
A new waypoint, with a default name and
data, is created at the boat position.
5-2-4 Displaying a waypoint on the chart
This goes to the chart window, and shows the
selected waypoint at the center of the window.
Change the waypoint data if necessary (see
section 5-2-7).
1
In the waypoints window, press
or
to highlight the waypoint to display. Press
Note: Waypoints can also be created when a
route is created (see section 6-2-1).
and select Display.
Or, in the Chart window, press
Find, then select Waypoints. Select a
waypoint from the list.
, select
5-2-2 Moving a waypoint
Moving a waypoint from the chart window
1
In the chart window, move the cursor to the
waypoint to move.
2
The 657 switches to the chart window, with
the selected waypoint at the center of the
chart.
2
3
Press
Move the cursor to the new position and
press
and select Move.
5-2-5 Deleting a waypoint
.
A waypoint can not be deleted if the boat is
navigating to it or if the waypoint is used in more
than one route. A waypoint that is used in one
route can be deleted.
Moving a waypoint from the waypoints
window
To move a waypoint from the waypoints window,
edit the waypoint (see section 5-2-3) and change
the latitude and longitude.
!
WARNING
When a waypoint is deleted from a route,
check that the changed route does not cross
land or dangerous waters.
5-2-3 Editing a waypoint
Editing a waypoint from the chart window
1
In the chart window, move the cursor to the
waypoint to edit.
26
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting a waypoint from the chart window
2
3
If necessary, repeat the above step to change
other data.
1
In the chart window, move the cursor to the
waypoint to delete.
Select Save.
2
3
Press
and select Delete.
5-2-8 Sort Waypoints
To change how the waypoints list is displayed:
Select Yesto confirm.
Deleting a waypoint from the waypoints
window
1
2
Press
and select Sort by.
Select how to display the list:
1
In the waypoints window, press
or
Name: In alphabetical order by name.
Icon: Grouped by icon type.
to highlight the waypoint to delete. Press
and select Delete.
Select Yesto confirm.
Distance: In order of distance from the
2
boat.
5-2-6 Deleting all waypoints
An arrow at at the top of a column indicates how
the waypoints are sorted.
1
In the waypoints window and press
and select Delete all.
Select Yesto confirm.
5-2-9 Navigating to a waypoint
See section 3-1-2.
2
5-2-7 Changing a waypoint’s data
To change the waypoint data when it is displayed
in a window:
1
Select the data to change.
Press
Use the cursor keys to change the data.
Press
.
.
6 Navigation: Routes
A route is a list of waypoints that the boat can
navigate along. Routes can be created, changed
and deleted.
Routes are a powerful feature when the 657 is
connected to an autopilot, allowing the vessel to
be automatically guided along the route.
The 657 can have up to 25 routes. Each route can
have up to 50 waypoints.
!
WARNING
Make sure the course does not pass over land
or dangerous waters.
A route can:
Start and stop at the same waypoint .
Include waypoints more than once.
The 657 can navigate along a route in either
direction. Waypoints on the route can be skipped.
Northstar Explorer 657 Installation and Operation Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
6-1 Routes window
The routes window is a list of the routes that
have been entered, each with route name, start
waypoint, end waypoint, number of legs and
total distance.
To go to the routes window, press
, select
More, then select Routes.
If there are more routes than will fit on the display,
press
or
to scroll up or down a page at
a time.
6-2 Managing routes
i
Change the name if necessary.
!
WARNING
ii Select OK.
To enter the legs of the route:
3
After creating or changing a route, display the
route on the chart and check that it does not
cross land or dangerous water.
i
Move the cursor to the start of the route
and press
.
ii A waypoint is created with a default
name. to save this waypoint press enter,
to edit the waypoint refer to 5-2-7
6-2-1 Creating a new route
A. Creating a new route from the chart
window
iii Press
a dotted leg line is displayed
While creating the route:
from the cursor to the previous waypoint
Press
or
to change the range; scroll
iv Move the cursor to the end of the first leg
the chart by moving the cursor to the edge of
the chart.
and press
.
v
Repeat i to iv until the last waypoint in
the route is placed and saved
A data box at the bottom left of the display
shows the route name and total distance. If
the cursor is near a leg, it shows the length
and bearing of the leg as well.
vi Press to complete the route
Menu options while creating a route:
1
To add a waypoint to the route
Press
The legs of a route must start and end at
waypoints. If a leg does not start or end at an
existing waypoint then a new waypoint will
be created automatically (to change the new
waypoint data, see section 5-2-7).
i
and select Add.
2
To insert a waypoint in the route by breaking
one leg into two:
i
Move the cursor to the leg you want to
break.
You can not use a Danger waypoint in a route.
1
In the chart window, press
New route.
The route is given a default name:
and select
ii Press
and select Insert.
iii Move the cursor to where the new route
waypoint will be.
2
28
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
iv Press
.
ii Press
. A list of waypoints is
displayed. Select the waypoint to use.
3
4
To move a waypoint in the route:
As waypoints are inserted, the distance and
bearing of each leg is shown automatically. If
the route has more waypoints than will fit on
i
Move the cursor to the waypoint to
move.
ii Press
and select Move.
the display, press
To remove a waypoint from the route:
Select the waypoint to remove.
ii Press
and select Remove.
Repeat this process until the route is finished.
Press
or
to see them.
iii Move the cursor to where the waypoint
will be.
5
i
iv Press
.
To remove a waypoint from the route:
6
7
8
i
Move the cursor to the waypoint to
remove from the route.
.
Display the route on the chart (see section
6-2-3) and check that the route does not cross
land or dangerous water.
ii Press
and select Remove. The
waypoint is removed from the route, but
the waypoint is not deleted.
5
6
7
To start navigating the route
6-2-2 Editing a route
Editing a route from the chart
i
Press
To end creating the route
Press
and select End
To delete the route
Press
and select Start
1
2
3
In the routes window, select the route to edit.
Press
and select Edit on chart.
i
The selected route is displayed on the chart,
with a circle around the first waypoint.
i
and select Delete
Edit the route as described in section 6-2-1 A,
starting at step 4.
ii Select yes to confirm.
Tip: The distance and bearing calculator can
Editing a route from the routes window
also be used to enter a course and save it as a
route (see section 3-3).
1
In the routes window, press
or
to
highlight the route to edit. Press
and
B. Creating a new route from the routes
window
select Edit.
2
3
The selected route is displayed: the route
name and a list of the waypoints.
1
2
3
In the routes window, press
and
select Create.
A new route, with a default name and no
waypoints, is displayed.
Edit the route as described in section 6-2-1 B,
starting at step 3.
6-2-3 Displaying a route on the chart
To change the route name:
To view the selected route at the center of the
display:
i
Select the route name at the top of the
display and press
ii Change the name if necessary.
iii Press
To insert a waypoint in the route:
.
1
2
In the routes window, press
highlight the route to display. Press
and select Display.
Or, in the Chart window, press
or
to
.
4
, select
i
Select where the waypoint will be:
Find, then select Route. Select a route
To insert the first waypoint in a new
route, select Leg 1.
from the list.
The 657 displays the selected route on the
chart.
To insert a waypoint at the end of
the route, select the unused leg at
the end of the list of waypoints.
Otherwise, select the waypoint to
insert the new waypoint in front of.
Northstar Explorer 657 Installation and Operation Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2-4 Deleting a route
6-2-5 Deleting all routes
1
In the routes window, press
and
1
In the routes window, press
or
to
select Delete all.
highlight the route to delete. Press
and select Delete.
Select Yesto confirm.
2
Select Yesto confirm.
2
6-2-6 Navigating a route
See section 3-1-3.
7 Satellites
Differential beacon DGPS
GPS worldwide navigation
Differential beacons are land based radio
transmitters that broadcast correction signals
that can be received by a special receiver
on the boat. Differential beacons are usually
only installed near ports and important
waterways, and each beacon has a limited
range. The accuracy of the corrected GPS
position is typically better than 2 to 5 m (6 to
16 ft).
The US Government operates the GPS system.
Twenty-four satellites orbit the earth and
broadcast position and time signals. The positions
of these satellites are constantly changing. The
GPS receiver analyses the signals from the closest
satellites and calculates exactly where it is on
earth. This is called the GPS position.
The accuracy of the GPS position is typically
better than 10 m (33 ft) for 95% of the time. A
GPS antenna can receive signals from the GPS
satellites when it is almost anywhere on earth.
GPS receiver
Northstar GPS units have a sensitive 12-channel
receiver, which tracks signals from all GPS
satellites visible above the horizon and uses
measurements from all satellites more than 5°
above the horizon to calculate the position.
DGPS
A DGPS system uses correction signals to remove
some of the errors in the GPS position. The 657
can use one of two types of DGPS system:
Each time a GPS receiver is turned on, it normally
takes about 50 seconds before it outputs the first
position. Under some circumstances it will take
up to two minutes or longer.
WAAS and EGNOS DGPS
WAAS and EGNOS are two satellite based
DGPS systems. The correction signals are
broadcast by satellites and are received by
the 657’s standard GPS antenna. The accuracy
of the corrected GPS position is typically
better than 5 m (15 ft) for 95% of the time.
WAAS covers all of the USA and most of
Canada. EGNOS will cover most of Western
Europe when it becomes operational.
30
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-1 Satellite window
The satellite window has information about the
GPS satellites and GPS position.
A
Status of GPS antenna, for example
Acquiring, GPS fix, No GPS. If the unit
is in Simulate mode it displays Simulate
(see section 2-6).
To go to the satellite window, press
,
select More, then select Satellite.
The satellite window shows:
B
Time and date from GPS satellites. Time is
local time (UTC [GMT] plus local offset, see
section 17-13)
A
C
D
HDOP: The error in the GPS position caused
by satellite geometry. A low value indicates a
more precise fix, a high value a less precise fix
B
C
F
Signal strengths of up to twelve visible GPS
satellites. The higher the bar the stronger the
signal
G
E
F
Boat position
Positions of visible GPS satellites:
Outer circle is horizon
Inner circle is 45° elevation
Center is directly above
North is at top of display
D
E
G
If the boat is moving, COG is a line from
center
8 Sonar fishfinding: Introduction
Sonar functions require an optional sonar
transducer to be installed and set up.
It also describes Gain and Range and shows
examples of some of the different sonar displays.
This section explains how to interpret the sonar
displays, when and why to use the different
frequencies and how fish are detected and
displayed.
8-1 Using the 657
The 657 uses a sonar transducer attached to
the hull. The transducer generates an ultrasonic
pulse (sound that is above the hearing range
of the human ear), which travels down towards
the bottom at a speed of about 4800 ft/sec
(1463 m/sec), spreading out into a cone shape.
the time taken between sending a pulse and
receiving the echo. When an echo has been
returned, the next pulse is sent.
The 657 converts each echo into an electronic
signal, displayed as a vertical line of pixels. The
most recent echo appears on the extreme right
of the display, with the older echoes being
scrolled towards the left, eventually disappearing
off the display.
When the pulse meets an object, such as a fish or
the bottom, it is partly reflected back up towards
the boat as an echo. The depth of the object or
bottom is calculated by the 657 by measuring
Northstar Explorer 657 Installation and Operation Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
The scroll speed depends upon the water depth
and scroll speed setting. See sections 17-3 and
section 8-2, for more information.
•
•
Fishing mode: Use this when fishing. The
657 automatically adjusts its settings to
compensate for water clarity and to best
display fish, the bottom and other details.
The appearance of echoes displayed are affected
by:
Manual mode: Use this to fine-tune the
657 settings by hand. Best results are often
achieved in manual mode, but practice
and experience are required to obtain the
optimum settings for different conditions.
•
•
•
the 657 settings (see sections 17-3, 8-5 and
8-6)
echoes (different fish types, different bottom
types, wrecks and seaweed; see section 8-2)
For more information about modes, see sections
8-5 and 8-6.
noise (water clarity and bubbles; see section
8-2).
Cruising, Fishing and Manual Modes
The 657 has three sonar operating modes:
!
WARNING
Use the automatic Cruising or Fishing modes
when learning to use the 657 or when
travelling at speed.
•
Cruising mode: Use this when on the move.
The 657 automatically adjusts its settings to
compensate for water clarity and to display
the bottom.
8-2 Interpreting the display
The sonar displays do not show a fixed distance
travelled by the boat; rather, they display a
history, showing what has passed below the boat
during a certain period of time.
Strength of echoes
The colours indicate differences in the strength of
the echo. The strength varies with several factors,
such as the:
The history of the sonar signal displayed depends
the depth of the water and the scroll speed
setting.
•
•
•
Size of the fish, school of fish or other object.
Depth of the fish or object.
Location of the fish or object. (The area
covered by the ultrasonic pulse is a rough
cone shape and the echoes are strongest in
the middle.)
In shallow water, the echoes have a short distance
to travel between the bottom and the boat. In
deep water, the history moves across the display
more slowly because the echoes take longer to
travel between the bottom and the boat. For
example, when the scroll speed is set to Fast,
at depths over 1000 ft (300 m) it takes about 2
minutes for the data to move across the display,
whereas at 20 ft (6 m) it takes only about 25
seconds.
•
•
Clarity of water. Particles or air in the water
reduce the strength of the echo.
Composition or density of the object or
bottom.
Note: Planing hulls at speed produce air
bubbles and turbulent water that bombard the
transducer. The resulting ultrasonic noise may
be picked up by the transducer and obscure the
real echoes.
The scroll speed can be set by the user to display
either a longer history with less fish information
or a shorter history with more fish details (see
section 17-3).
If the boat is anchored, the echoes all come from
the same area of bottom. This produces a flat
bottom trace on the display.
The screen shot shows a typical sonar display
with the Fish symbols turned Off.
32
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
A
B
C
C
D
A
B
Single fish
A
B
Kelp / Weed
Large school of fish
Small school of fish
Bottom
Soft bottoms such as mud, weed and sand
show as narrow bands
C
D
C
Hard bottoms such as rock or coral show as
wide bands
Bottom types
Mud, weed and sandy bottoms tend to weaken
and scatter the sonar pulse, resulting in a weak
echo. Hard, rocky or coral bottoms reflect the
pulse, resulting in a strong echo.
Frequency and cone width
The sonar pulse
generated by the 657
transducer travels down
through the water,
spreading outwards in
a cone shape. The cone
width is dependent
upon the frequency of
the pulse; at 50 kHz it
is approximately 45°,
and at 200 kHz it is
Water
Depth
Cone width
at 50 kHz
Cone width
at 200 kHz
25
50
100
150
200
20
40
80
130
170
5
10
20
30
40
11°
cone
45° cone
300
400
600
250
330
500
660
830
60
80
approximately 11°.
The differences in the
cone width affect what is
displayed. See
120
150
190
section 8-3.
800
1000
Northstar Explorer 657 Installation and Operation Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Shadows
Shadows are created around areas where the ultrasonic beam cannot ‘see’. These areas include hollows
on the bottom or beside rocks and ledges, where the strong echoes returned off the rocks obscure the
weak echoes of the fish and may also create a double bottom trace. See following for an example of the
sonar display in such an environment. A double bottom trace is shown on the display.
When looking for fish with the wide angled 50 kHz frequency, be aware of increased shadows. Use the
high frequency 200 kHz in areas that have rocks and ledges because this frequency reduces the shadow
effect considerably.
Sonar display of same area
Example of shadows
A
B
A
B
A
B
Fish is visible on the display
Fish is hidden by the strong
echoes off the bottom and is not
shown on the display
A
A
8-3 Single and Dual frequency fishfinding
Sonar frequencies
The 657 has two sonar frequencies, 200 kHz and
50 kHz. To select the sonar frequency to use:
discrimination capability and is particularly good
at showing individual fish, including bottom
dwellers.
When to use 50 kHz
The 50 kHz frequency is particularly suitable for
use in deep water, typically greater than 500 ft
(150 m).
1
2
Go to a sonar display (see section 9).
Press
, select Frequencyand select
200 kHz, 50 kHz,or Mixed.
When to use 200 kHz
At 50 kHz, the cone covers an area of water about
four times wider than the 200 kHz cone and
penetrates to a greater depth with minimal loss of
the return signal.
The 200 kHz frequency is especially suitable for
use in shallow and medium depth water, typically
less than 500 ft (150 m) and while running at
speed.
However, it produces a lower definition display
with more shadow compared to the 200 kHz
frequency. This means that a group of small fish,
for example, could be displayed as a single item,
while any fish very close to the bottom may not
be found at all.
At 200 kHz, the narrow cone reduces any noise
caused by air bubbles.
The 200 kHz frequency generates a higher
definition pulse which produces little shadow
and returns excellent detail over a small area
of bottom. Therefore, it gives excellent bottom
34
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
This frequency is useful for getting a deep, wide
overview of the area so that any areas of interest
can be identified and then examined in detail
with the 200 kHz frequency.
When to use Mixed
The Mixed frequency combines the 200 kHz and
the 50 kHz echoes on one sonar display, filling
in detailed echoes in the center of the sonar cone.
When to use 50/200 kHz
A
Operating the 657 at both 50 kHz and 200 kHz
simultaneously on a split display can be very
useful when operating in shallow to medium
water, typically less than 500 ft (150 m), because
the 50 kHz section of the display shows the
general area, while the 200 kHz section can be
viewed simultaneously for a more detailed look at
any interesting feature.
B
B
A
B
Narrow angle, more detailed 200 kHz cone
Wide angle, less detailed 50 kHz cone
To use 50/200 kHz, select the Split 50/200 display
(see section 9-4).
Northstar Explorer 657 Installation and Operation Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Comparison of the same fish scenario displayed at different frequencies:
1 minute ago
30 seconds ago
Now
50 kHz display
200 kHz display
200/50 Khz display
Mixed display
36
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-4 Fish detection and display
Where to find fish
Underwater features like reefs, wrecks and rocky
outcrops attract fish. Use the 50 kHz or 50/200
kHz frequency display to find these features, then
look for fish by passing over the feature slowly
several times using the Zoom display (see section
9-2). If there is a current, the fish will often be
found downstream of the feature.
A fish arch starts when a fish enters the weak
edge of the sonar cone, generating a weak echo
that is displayed as the start of the fish arch. As
the fish moves closer to the middle of the cone,
the distance between the transducer and the fish
reduces and the echo is displayed at progressively
shallower depths, producing a rising shape. When
the fish passes directly beneath the middle of the
cone, the echo becomes strongest and thickest.
As the fish passes out of the middle of the cone
the reverse happens with a progressively weaker
and deeper echo.
When fishing with the 657 with the Fish symbols
Off, a weak fuzzy band may appear between
the bottom trace and surface. This might
indicate a thermocline - a rapid change in water
temperature, such as the edge of a warm or
cold current. The temperature difference can
form a barrier which the fish may not swim
through. In fresh water, fish often collect around
a thermocline.
There are many reasons why fish arches may not
be seen. For example:
•
Poor transducer installation (see Transom
Transducers Installation Guide).
•
If the boat is anchored then fish will tend to
show on the display as horizontal lines as they
swim into and out of the transducer sonar
beam. Slow speeds in deeper water give the
best fish arch returns.
Fish symbols
The 657 uses Northstar’s SBN II technology to
analyse sonar echoes and identify which are
likely to be fish. The 657 can be set up to display
a fish symbol and the depth over these echoes
(see section 17-3, Fish symbols). While SBN is
very sophisticated it is not foolproof - there
will be times when the 657 will not be able to
differentiate between fish and large air bubbles
or rubbish.
•
Range is important. It will be much easier to
see fish arches when using zoom mode to
concentrate on a particular section of water,
rather than just displaying everything from
the surface to the bottom. Zooming increases
screen resolution and is necessary for good
fish arches.
Depending on the strength of a fish signal, the
657 can display a small, medium or large symbol
(see section 17-3, Fish filter).
•
It is difficult to get fish arches in shallow water
as the transducer sonar beam is very narrow
near the surface and fish do not stay within
the beam long enough to display an arch.
Several fish in shallow water tend to display as
randomly stacked areas of color.
To see the maximum amount of information from
the echoes, turn Fish symbols off. Fish appear as
arches on the display.
Fish arches
•
Wave motion may result in distorted fish
arches.
In good conditions, a fish passing through the
cone-shaped ultrasonic pulse is displayed as a
fish arch. The 50 kHz frequency uses a wider cone
than the 200 kHz frequency. This makes the fish
arches easier to see.
Fun fish symbol
Normal fish symbol
Fun symbol + depth
Fish arch + depth
Northstar Explorer 657 Installation and Operation Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
8-5 Range
Range is the vertical depth displayed on the 657
sonar display. For example, if the range is 100 m,
then the sonar display shows depths between 0
and 100 m. The range is displayed at the bottom,
right corner of a sonar display.
To set Manual range or to change the range:
1
2
Go to a sonar display (see section 9).
Either press to increase range or
press to decrease range
The 657 has two range modes:
!
WARNING
Auto: The 657 adjusts the range automatically
so that the bottom of the water is always
shown at the bottom of the display. Auto
range is recommended for normal operation.
Use the Auto range when learning to use the
657 or when travelling at speed.
Zoom range and offset
To set Auto mode:
The sonar Zoom and Bottom displays can show
a magnified part of the range (see sections 9-2
and 9-3).
1
2
Go to a sonar display (see section 9).
Press
, select Rangeand select
Auto.
Manual: The 657 does not adjust the range
automatically. If the bottom depth is below
the range, the bottom will not appear on
the display. Manual range is useful if the
bottom depth changes rapidly, because Auto
range will cause the display to change range
frequently.
38
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-6 Gain and threshold
Gain and threshold settings control the amount
of detail displayed on a sonar display:
Changing mode
The 657 has three operating modes, In Cruising
and Fishing modes, the 657 automatically adjusts
gain and threshold for good performance. In
manual mode, you can hand adjust the settings.
Gain: The gain of the sonar receiver. The gain
should be high to display good detail, but if the
gain is too high then information from the strong
bottom signal is lost and false echoes might be
displayed. There is a separate gain setting for
each sonar frequency, 50 kHz and 200 kHz.
To change the mode from the Gain window,
Select Modeand then select Fishing,
Cruisingor Manual. When you select
Manual, the 657 reverts to your last manual
settings.
Threshold: Return echoes less than the
threshold are ignored. The threshold should be
as low as possible, but if the threshold is too low,
unwanted noise will be displayed. Threshold is
set as a percentage of gain. For example, if the
threshold is 50 %, then return echoes less than
50 % of the maximum signal are ignored. There
is a separate threshold setting for each sonar
frequency, 50 kHz and 200 kHz.
Changing gain and threshold
1
In the Gain window, press
the setting to adjust.
or
to select
2
Press
or
adjust the setting. The 657
changes to Manual mode.
Tip: Use the A-scope window to help set gain
or threshold manually (see section 9-5).
The gain window
To display or change the current settings for gain,
select a sonar display and press
. Select
Thresholdto display the thresholds.
This display is called the gain window.
Northstar Explorer 657 Installation and Operation Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Sonar fishfinding: Displays
Split A-Scope: Sonar history plus echo strength
To show the Sonar display, press
, then
(see section 9-5).
select Sonar.
If the display is split, adjust the split ratio if
required:
There are five kinds of sonar display. To use a
display, press
then select the type of display to use:
, select Sonar splits,
1
2
3
Press
Press
Press
and select Sonar display split.
to adjust the ratio.
No split: Sonar history display at a single or
or
mixed frequency (see section 9-1).
.
Split zoom: Sonar history plus a zoomed section
(see section 9-2).
Full screen zoom: See section 9-2.
Split bottom: Sonar history plus a bottom trace
in a zoomed section (see section 9-3).
Split 50/200: Sonar histories at 50 and 200 kHz
(see section 9-4).
9-1 Sonar history display - no split
A
B
C
D
E
Optional data header (see section 2-7-3)
A
Depth
Color bar
B
C
Bottom
Range
F
Fish symbols with depth
Depth line
G
The window scrolls from right (most recent
echoes) to left (oldest echoes).
G
F
D
E
40
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-1-1 Extended history mode
To review an old sonar echo, use
or
to
move back and forward through the sonar
history. The time since the echoes shown on the
screen were recorded is displayed at the bottom
of the screen. Press
recent echo.
to return to the most
The digital depth shown is always the current
depth, even in extended history mode.
The History Position Bar indicates the age of the
most resent echo on the screen, and the position
of the current screen in the recorded history.
History position bar
9-2 Sonar Zoom and Full Screen Zoom displays
These windows show a zoomed section of the
sonar history. The Sonar Zoom display shows
the sonar history on the right and the zoomed
section on the left. The Full Screen Zoom display
shows the zoomed section only.
A
The zoom bar on the far right shows the area of
the history that is magnified in the zoom section:
•
Press
or
to adjust the zoom range
B
C
(the range of depths included in the zoom
section).
•
If Bottom lockis on, the zoom depth
(the depth of the zoom section) is adjusted
automatically so that the bottom is always
displayed in the zoom section.
If Bottom lockis off, press
or
to
D
E
manually adjust the the zoom depth.
A
B
Divider line
Bottom lock
Depth line marks the center of the zoomed
area
To turn Bottom lockon or off:
1
Press
and select Bottom lock.
C
D
E
Zoom bar
2
Select Onor Off.
Zoom section
Sonar history
or If Bottom lockis on, pressing
or
will turn it off.
Northstar Explorer 657 Installation and Operation Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
9-3 Sonar Bottom display
The display shows the sonar history on the right
and the bottom signal as a flat trace in the center
of the zoom section on the left. The flat trace
make it easy to compare the echo strengths
shown in the bottom signals. This can help to
identify the type of bottom and objects close to
the bottom.
The zoom bar on the far right shows the area of
the history that is magnified in the zoom section:
•
Use the
range.
or
keys to adjust the zoom
A
•
The 657 calculates the zoom depth
automatically.
It is not necessary to turn Bottom lock on for this
display.
B
A
B
Zoomed bottom signal
Sonar history
9-4 Sonar 50/200 display
The display shows:
A
B
the 50 kHz sonar history on the left
the 200 kHz sonar history on the right.
Gain can be set independently for each
frequency (see section 8-6). Range applies to
both frequencies (see section 8-5).
B
A
42
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-5 Sonar A-Scope display
The display shows the sonar history on the
left and the A-Scope display on the right. The
A-Scope shows:
A, B, C The strengths of echoes being received
now from different depths - the longer the
horizontal line the stronger the signal:
A
A
B
C
Unwanted noise echoes.
Echoes from fish and the bottom
The strongest echo, usually from the
bottom
E
B
D
E
A vertical line showing the threshold, the
weakest echo to display on the sonar history
D
C
B
A vertical line showing the gain setting;
echoes above this strength will display as the
maximum signal strength
A
Use the A-Scope while adjusting the gain and
threshold settings manually (see section 8-6).
8
9
Press
to close the gain window.
Setting gain and threshold
It is convenient to use the A-scope display when
adjusting gain and threshold manually. Follow
this procedure to adjust gain and threshold for
normal circumstances:
If required, repeat these steps to adjust gain
and threshold for the other frequency.
Note: Setting the gain higher will display more
detail from weak echoes, like fish, but will loose
detail from the strong echo from the bottom.
1
Switch to a sonar display (see section 9). If
necessary, press or to adjust range
Fish recognition
so that the bottom is displayed.
The echo strengths shown on the A-scope can
be useful in recognising the type of fish. Different
species of fish have different sizes and shapes
of swim bladders. The air in the swim bladder
reflects the ultrasonic pulse, so the strength of
the echo varies between fish species according to
the size and shape of the swim bladder.
2
If necessary, select the sonar frequency to
adjust the settings for. Press
, select
Frequencyand select 200 kHzor 50
kHz.
Press
3
4
, select Sonar splits then select
Split A-scope.
Press
to display the Gain window. To
When catching fish from a school, note the
species and the strength of the echo that
it returns on the A-scope. Then, when that
particular echo is seen again, it is likely to be the
same fish species.
adjust gain or threshold for a frequency, press
or
press
to select the setting to adjust, then
or to change the setting.
5
6
Set threshold to zero.
Bottom type
The shape of the echo strengths in the A-Scope
Adjust Gain so the peak of the strong signal
from the bottom just touches the gain line.
can help you to recognise the type of bottom.
7
Adjust threshold so that it is just to the right
of the noise.
Northstar Explorer 657 Installation and Operation Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Gauges window
The Gauges window shows boat data, such as
water speed, as analog gauges. To select the
Gauges window, press
, select More, then
select Gauges. Before using the Gauges window,
set Speed range, Max RPM and Max fuel flow (see
section 17-12).
Selecting a Gauges layout
To select a layout from the Gauges window, press
, select Layout, then select a layout from
the list.
Changing a gauge layout
You can change the data displayed on each
gauge in a layout.
1
2
3
Select the layout to change (see above).
Press and select Gauge setup.
Highlight the gauge to change. Press
and select the data to display in the gauge.
4
5
Repeat the above step to change other
gauges.
Press
.
11 Data window
The data window has large numeric data fields
and a graph of depth and water temperature if
available. To go to the data window, press
select More, then select Data.
,
To select what data is displayed:
1
2
Press and select Data setup.
Change a data field:
i
Press the cursor keys to highlight the
field.
ii Press
items.
to display a menu of data
iii Select a data item that is available on your
system or select Noneto leave the field
empty.
3
4
Repeat the above step to set the other data
fields.
Press
.
44
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Fuel functions and display
The Fuel functions require optional petrol/gasoline or SmartCraft™ fuel sensors to be installed and set
up.
12-1 What the fuel computer does
Each engine has a flow sensor installed to
measure the engine’s fuel flow.
!
WARNING
The 657 uses these flows, together with boat
speed and engine RPM if available to estimate the
fuel remaining in the tank(s), fuel used, range and
fuel economy. This data is displayed on the fuel
window (see section 12-2).
To ensure the fuel data is accurate:
When you add or remove fuel from a
tank, tell the 657 (see section 12-3)
If the boat has petrol/gasoline sensors,
calibrate them during installation or if
the fuel readings seem inaccurate (see
section 12-7)
You can:
display the fuel used during a trip
(see section 12-2)
Choose an appropriate type of boat
speed sensor to calculate economy,
range and the fuel consumption curve
(see section 12-5)
set low fuel alarms (see section 12-4)
make fuel consumption curves - graphs
of fuel consumption and boat speed as a
function of engine RPM - to monitor and
optimise boat performance.
If the boat uses a paddlewheel sensor
to measure speed, calibrate it during
installation or if the speed readings seem
inaccurate.
(see section 12-6)
12-2 Fuel window
alarm (see section 12-4), a red bar shows the level
at which the alarm will trigger. If there are two
tanks, the left bar shows the port tank, the right
bar shows the starboard tank.
To go to the Fuel window, press
More, then select Fuel.
The display differs according to the number of
engines and tanks. If engine RPM is available
and if you have made and selected a Fuel
Consumption Curve (see section 12-6), press
to switch between a Summary or a Fuel curve
display.
, select
Used
The fuel used during a trip. On a multi-engine
boat, the data for the port engine is on the left of
the display.
When you want to start measuring how much
fuel is used, go to the Fuel window and:
The Fuel window shows
Speed
In a single engine boat, press
select Clear used.
In a multi-engine boat, the fuel used by each
engine and the total fuel used are shown.
and
To select a boat speed sensor, see section 12-5-1.
RPM (if available)
If engine RPM is not available, the display shows
depth.
Press
select:
, select Clear usedand
Remaining
The fuel remaining in the tank(s) is shown as a
vertical gauge on the right of the display. The
height of the yellow bar(s) show how much fuel
remains in the tank(s). If you have set a low fuel
Portor Starboardto clear the fuel used
by one engine
Both to clear the total fuel used.
Northstar Explorer 657 Installation and Operation Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Fuel window
Fuel flow
The fuel flow for the engine(s). On a multi engine
boat, the data for the port engine is on the left
of the display. Use the flows to check the load of
each engine.
Range
The estimated boat range at the current fuel
flow. The value can depend on the type of speed
sensor (see section 12-5).
Economy
The distance travelled per unit of fuel used. The
value can depend on the type of speed sensor
(see section 12-5). The larger the value, the better
the fuel economy. Adjust the throttle and trim to
achieve the best economy.
Fuel consumption curve
A graph of fuel consumption and boat speed
as a function of engine RPM. Use the curve to
monitor and optimise boat performance (see
section 12-6).
12-3 When you add or remove fuel
When you add or remove fuel, you must tell the
657, otherwise the fuel data will be meaningless.
B
When you partially fill a tank
1
Add fuel to a tank and write down how much
fuel you add.
A
When you completely fill a tank
Go to the fuel window and press
Then:
.
2
3
4
From the Fuel window, press
select Add fuel.
On a multi-tank boat, select the tank that you
have added fuel to.
and
On a single-tank boat, select Fill tank.
On a multi-tank boat, select Fill tank,
Change the number to the amount of fuel
that you added.
then select the tank you have filled.
Note: Underfloor fuel tanks are often difficult to
Note: If you follow procedure B every time you
add fuel, then a small error will accumulate,
because it is hard to measure exactly how much
fuel you add. To avoid this, completely fill the tank
and follow procedure A about every tenth time
you add fuel.
refill to the same level twice, due to air pockets.
With underfloor fuel tanks:
Trim the boat to the same angle in the water
each time you follow procedure A.
Mostly use procedure B below when adding
fuel, but completely fill the tank and follow
procedure A about every tenth time you add
fuel.
46
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
C
When you remove fuel
6
7
Change the number on the Set Remaining
menu to the amount of fuel that you
calculated was now in the tank.
1
Before removing fuel, go to the Fuel window,
press
and select Set remaining.
Press
2
3
On a multi-tank boat, select the tank that you
are removing fuel from.
Note: You can also use this procedure when you
add fuel to a tank. In this case, add the fuel you
have added to the amount of fuel originally in
the tank to calculate the amount of fuel now in
the tank.
Write down the value of Remaining for the
tank; this is the amount of fuel originally in
the tank.
4
5
Remove fuel from the tank and write down
how much fuel you remove.
Subtract the amount of fuel you removed
from the amount of fuel originally in the tank
to calculate the amount of fuel now in the
tank.
12-4 Low fuel alarm
To set a low fuel alarm for a tank:
When a low fuel alarm is set, the alarm’s fuel level
is shown on the fuel window tank levels as a red
bar. The alarm can also be set using the Alarms
setup menu (see section 17-9)
1
2
3
Press
Setup tanks.
On a multi-tank boat, select the tank to set
the alarm for.
twice, select Fuelthen select
Select Tankalarmand enter a fuel level to
trigger the low fuel alarm.
12-5 Boat speed sensors
To select an optional speed sensor
12-5-1 Selecting a boat speed sensor
The fuel calculations can use boat speeds from
the GPS, or from a paddlewheel sensor or pitot
sensor if these optional sensors are installed:
1
Press
Speed source.
To use a paddlewheel or pitot sensor, select
Water speed, otherwise select Ground
speedto use GPS speed.
twice, select Fueland select
2
Paddlewheel and pitot sensors measure the
speed through the water; GPS speed is speed
over ground; these sensors can give different
values for Range, Economy and the fuel
consumption curves (see section 12-5-2).
3
If you selected Water speed and you have
both a paddlewheel sensor and a pitot
sensor:
A pitot sensor is more accurate than a
paddlewheel sensor at high speeds but is
not accurate at low speeds. A paddlewheel
sensor is more accurate than a pitot sensor at
low speeds.
i
Press
, select SmartCraftand
select Speed type
ii Select Paddlewheelor Pitot.
Tip: You can select a different speed sensor
during a trip.
Northstar Explorer 657 Installation and Operation Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
12-5-2 Water speed and ground speed
A paddlewheel sensor and a pitot sensor
measure water speed, the boat speed through
the water. A GPS measures ground speed, the
boat speed over the bottom of the water. If
there is a current, then these speeds will be
different, and the log, trip log, economy and
range will be different, as shown below.
Water speed is better for measuring the boat’s
potential performance, Ground speed is better
for going to a destination because it takes
currents into account. To select a speed sensor,
see section 12-5-1.
When the current is from ahead, ground speed is less than water speed
Water speed 10 knots Water speed 10 knots
Current 4 knots
Gives a ground speed
of about 8 knots
Gives a ground speed of 6 knots
Current 4 knots at 45º
For this example:
If the boat travels for one hour, uses 3 gallons of fuel per hour and has 50 gallons of fuel left:
Speed
10 knots
6 knots
Log
Economy
3.3 nm / gal
2.0 nm / gal
Range
165 nm
100 nm
Using water speed:
Using ground speed:
10 nm
6 nm
When the current is from behind, ground speed is more than water speed
Water speed 10 knots
Current
Current 4
knots at 45º
Water speed 10 knots
4 knots
Gives a ground speed of 14 knots
Gives a ground speed of about 13 knots
For this example:
If the boat travels for one hour, uses 3 gallons of fuel and has 50 gallons of fuel left:
Speed
Log
Economy
3.3 nm / gal
4.7 nm / gal
Range
165 nm
235 nm
Using water speed:
Using ground speed:
10 knots
14 knots
10 nm
14 nm
48
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
12-6 Fuel consumption curves
A fuel consumption curve shows fuel
Now, do not change the engine speed.
Wait for about 60 seconds for the boat to
consumption (fuel used per unit of distance
travelled) and boat speed as a function of
engine RPM. Fuel consumption curves require
engine RPM, which requires SmartCraft™ or
diesel sensors to be installed. Fuel consumption
curves are powerful tools for assessing boat
performance in different conditions and for
helping you to run at the most economical speed
and trim for the conditions.
stabilise, then press
. Wait while the fuel
computer records the data.
7
The 657 then asks you to set the throttle to
achieve a vessel RPM. On a multi engine boat
set all engines to about the vessel RPM. When
the engine RPMs are correct, the Vessel RPM
box will turn green.
Now, do not change the engine speed.
Wait for about 60 seconds for the boat to
stabilise, ensuring the Vessel RPM box stays
12-6-1 Making a fuel consumption curve
To make a fuel consumption curve you will need
to run the boat in a straight line for about 15
minutes using the engine’s full RPM range. For
your first curve, choose a calm day with light
wind and little current; have a typical load and
a freshly cleaned hull. Later, you can make fuel
consumption curves for different boat, weather
or sea conditions. Compare these with your
first curve to see how your boat’s performance
changes with conditions.
green. Then press
computer records the data.
. Wait while the fuel
Making a curve
1
2
Start running the boat in a straight line.
Choose a speed source for the curve (see
section 12-5-1). Normally choose Water speed
to measure the boat’s potential performance.
3
4
Press
twice, then select Fuel.
Select Fuel consumption curve, then
select New.
8
The 657 repeats the above step to record data
up to the maximum RPM. Then the 657 asks
if you want to save the curve. Select Yes. The
fuel computer asks for a name for the curve.
Change the default name if required. Then
5
Enter the comfortable maximum RPM you
know you can achieve for the engine rather
than the maker’s value.
press
Note: To interrupt making the curve at any time,
press
. The 657 stores the new curve.
.
6
The 657 then asks you to set the minimum
RPM. Set the throttle to idle; on a multi
engine boat set all engines to about the same
idle RPM.
Northstar Explorer 657 Installation and Operation Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a curve
12-6-2 Managing fuel consumption curves
Renaming a curve
1
2
Press
twice, then select Fuel.
F
E
C
Select Fuel consumption curve.
Select Name and select the name of the
curve to rename.
D
B
3
Select Rename and press
. Change
the name.
A
12-6-3 Using fuel consumption curves
Compare your boat’s performance now, at the
current RPMs, with the boat’s performance when
you made the curve. You can compare your
boat’s performance now with a curve made
under ideal conditions or with a curve made
under similar conditions.
Deleting a curve
1
2
Press
twice, then select Fuel.
Select Fuel consumption curve.
Select Name and select the name of the
curve to delete.
3
Select Delete.
Information in a curve
Selecting a curve
A
RPM of the boat now. For a twin engine boat,
the RPM is the average of the two RPMs.
1
You must make a fuel consumption curve
before you can use it (see section 12-6-1).
B
Red curve: boat speeds at different
RPMs recorded when you made this fuel
consumption curve.
2
On the Fuel window, press
Fuel consumption curve and select the name
of the curve to use.
, select
C
Red marker: the boat speed now. This marker
is below the red curve, showing that the boat
speed now at this RPM is less than when you
recorded the curve.
3
On the fuel window, press
to select Fuel curve and display the fuel
consumption curve.
if necessary
D
E
Blue curve: fuel consumption at different
RPMs recorded when you made this fuel
consumption curve.
Note:
a
On a multi engine boat, keep the RPM of all
engines similar while using a curve.
Blue marker: the fuel consumption now. This
marker is below the blue curve, showing
that the fuel consumption now at this RPM is
better than when you recorded the curve.
b
The shape of the curve depends on the type
of speed sensor you selected when making
the curve (see sections 12-5-1 and 12-5).
F
If the blue curve has a dip, then running the
boat at this RPM will give the best speed for
the least fuel consumption.
50
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
12-7 Calibration
Calibrate petrol/gasoline fuel flow sensors
during installation, or if the fuel readings seem
inaccurate and the other troubleshooting
suggestions do not help (see appendix B
troubleshooting).
To calibrate the sensor(s):
1
2
Record the level of the fuel in the tank(s).
Connect the portable tank(s) to the engine
through the fuel sensor(s).
3
4
Run the engine at normal cruising speed until
at least 4 gallons (15 litres) of fuel has been
used per engine.
Note
SmartCraft™ fuel sensors are factory
calibrated and should never need
recalibrating.
Check the actual amount of fuel used per
engine by refilling the portable tank(s) to the
original level and noting the reading(s) of the
fuel dispenser’s gauge.
On a multi engine boat, calibrate each
engine’s sensor. This can be done at the same
time with a portable tank for each engine or
at different times using one portable tank.
5
6
Press
Setup engines.
On a single engine boat, select Calibrate
and change the displayed value to be equal
to the reading of the fuel dispenser’s gauge,
twice, select Fuelthen select
Calibrating a sensor requires accurate
measurement of the fuel consumption.
This is best done using a small portable tank.
At least 4 gallons (15 litres) of fuel should be
used to ensure an accurate calibration.
then press
.
On a multi-engine boat select the engine.
Select Calibrateand change the
It is often very difficult to fill underfloor tanks
to the same level twice due to air pockets, so
the more fuel used, the more accurate the
calibration.
displayed value to be equal to the reading of
the fuel dispenser’s gauge, then press
Repeat for the other engines.
.
Northstar Explorer 657 Installation and Operation Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
13 Tides window
The tides window is available on C-MAP charts.
The tides window shows tide information at a
tide station for the selected date.
3
A list of tide stations are displayed. Select the
tide station to display. The chart redraws with
the tide station centred.
Note: The tides window requires the local time
offset to be set to work correctly (see section
17-13)
4
5
Press
and select Chart info.
Select Tide height.
Choosing the date of the tide chart
To show the tides window for the tide station
1
2
Press
.
nearest to the boat, press
then select Tides.
To go to the tides window for any tide station:
, select More,
Select Today, Next dayor Prev day.
To choose a different date from these, select
Set date, edit the date,
1
2
From the chart window, press
and
press
.
select Find.
Select Tide stations.
The tides window shows data for the chosen date
A
B
C
D
E
Tide station name and distance from boat
N
A
B
Current time and chosen date for display
Tide chart
Night
Dawn
K
F
Day
G
H
I
Dusk
E
G
Tide height
D
D
F
Time cursor, a vertical dotted line. Press
to move cursor sideways
or
C
L
I
J
Time of cursor and tide height at that time
Data for the chosen date
K
L
H
J
Tide height cursor, a horizontal dotted line.
Press
M
or
to move cursor up and down.
M
N
Height of cursor on the tide chart
Moon phase for moon at the current time on
the chosen date
CAUTION
The tides window requires the local time
offset to be set to work correctly (see section
17-13)
52
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
14 User card window
A C-MAP™ user card is an optional plug-in card
that can store data files (see section 1-3). There
are three types of files: waypoints, routes or a
track.
To go to the user card window, press
,
select More, then select User card.
CAUTION
Before using a user card, remove any chart
card and plug the user card in. When you
have finished with the user card, remove
the user card and replace the chart card
(see section 1-3).
1
2
The older 5 volt cards are not supported.
The user card window has:
File list
A list of the files on any user card in the 657. If
there are more files than will fit on the display,
press
or
to scroll up or down a page at
a time.
Loading data from the user card to the 657
This loads one file from the user card to the 657:
Waypts, Routes
The number of waypoints and routes currently
in the 657.
A waypoints file: The new waypoints are
added to any existing waypoints in the 657.
If a new waypoint has the same name as an
existing waypoint but has different data, the
657 displays both waypoints. Select:
Track 1 to Track 5
The number of points in tracks 1 to 5 currently
in the 657.
Skip: Do not load the new waypoint.
Note:
Replace: Load the new waypoint and
1
To save 657 data onto the user card, use the
Save command (see below).
replace the existing one.
Skip all: Do not load any new
waypoints which have the same names
as existing waypoints.
2
Data stored on the user card and shown on
the file list is not available to be used by the
657 until loaded into the 657 with the LOAD
command (see below).
Rplc all: Load all new waypoints
which have the same names as existing
waypoints; the new waypoints replace
the existing waypoints.
Saving data to the user card
This saves all the 657’s waypoints, all the 657’s
routes or one of the 657’s tracks to one file on the
user card.
A routes file: The new routes are added to any
existing routes in the 657. If a new route has
the same name as an existing route but has
different data then the 657 asks which route
to keep.
1
2
3
4
Press
and select Save.
Select Waypts, Routesor Tracks.
For Tracks, select the track number to save.
A track file: The new track will replace the
existing track in the 657.
The new file is created. Change the name
if required. The new file appears in the
file list.
Northstar Explorer 657 Installation and Operation Manual
53
Download from Www.Somanuals.com. All Manuals Search And Download.
To load a file to the 657:
1
2
3
Press
and select Card.
1
2
Select the file to load.
Press
and select Load.
Select Format.
Select Yes to confirm.
Deleting a file from the user card
Sorting the file names
This sorts the displayed file names.
1
Select the file to delete.
2
3
Press
and select Delete.
1
2
Press
and select Sort.
Select sort by Name, Typeor Time.
Select Yesto confirm.
Rereading the file information
This reads the file names from the user card and
displays them. Reading does not load any file
data into the 657. You should not need to do this.
!
WARNING
Do not format a chart card.
1
2
Press
and select Card.
Select Read.
Formatting the user card
Formatting prepares a user card for use. Format
the card if there is an error message saying that
the card is not formatted. Any data files on the
card are deleted.
15 AIS
AIS is short for Automatic Identification System.
The International Convention for Safety of Life At
Sea (SOLAS) requires all vessels greater than 300
tons and all passenger vessels to be equipped
with AIS Transponders. All vessels equipped with
AIS permanently broadcast via one or more of the
two dedicated VHF channels. This transmission
may include information about the vessels MMSI-
number, its call sign, name, position, course,
heading, speed, rate of turn and type of vessel.
The following AIS receivers are supported by
this unit:
•
•
Comar SLR200 (external GPS).
Weatherdock Two Channel AIS Receiver “EASY
AIS”, Part No. 5-A-013 (external GPS).
•
NASA Marine AIS Engine 2 channel Receiver
(external GPS).
Other AIS receivers may work but have not been
tested with this unit.
This unit can receive and display AIS information
when connected to an AIS receiver. Available AIS
vessels transmitting in the local area are show on
the chart when this feature is enabled.
To enable AIS from the system menu check the
AIS box. (see section 15-1)
54
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
15-1 Viewing AIS Vessels
C
A
B
D
Press either
information.
or
to clear the
A
AIS Vessel
15-2 Dangerous Vessels
The 657 calculates the time of closest point of
approach (TCPA) and closest point of approach
(CPA) for each AIS vessel.
B
Dangerous Vessel
Projected Course
Data Box
C
D
When the cursor is placed over an AIS vessel for
at least two seconds, a data box appears at the
bottom of the window with information about
the AIS vessel.
This is used to determine potential dangerous
vessels. If the TCPA and the CPA is below
the trigger values then it will be considered
dangerous. (See section 17-9 for setting the
dangerous vessel alarm)
For complete AIS information on the AIS vessel
place the cursor over an AIS vessel for at least two
seconds and press
A dangerous vessel is indicated on the chart by a
red circle around the icon.
.
TCPA 15 min
CPA 0.5 nm
Northstar Explorer 657 Installation and Operation Manual
55
Download from Www.Somanuals.com. All Manuals Search And Download.
15-3 AIS Windows
To go to the AIS windows, press
Displaying Full AIS Details
1
Press
or
to select a vessel.
, select
More, then press
or
to select one of the
2
Press
press
and select More Infoor
two windows: Vessels or Safety msgs (rx).
.
If there are more items than will fit on the
This window displays all information for
the selected AIS vessel provided by the AIS
receiver.
window, press
or
to see the others.
Sorting Vessels
Press
, select Sort and select one of
the options.
This sorts the list based on the chosen
category.
Safety msgs (rx)
Vessels
This is a sorted list of vessels currently being
received by the AIS receiver. The maximum
number of vessels that the system will support is
250. Once maximum is reached, vessels furthest
away from the current location will be replaced.
A vessel will be removed from the list if no
information is received within 6 minutes from the
last message.
Safety msgs (rx) are broadcasted messages
received by the AIS receiver. This window displays
the date and time of message received, MMSI of
AIS vessel that broadcasted the message, and the
message itself. Safety msgs (rx) list will store up
to 10 messages. The oldest message is replaced
when the list is full.
Displaying an AIS vessel on the chart
1
Press
or
to select a vessel.
2
Press
and select Display. The
Instrument switches to chart window, with
the selected vessel position in the middle.
56
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
16 DSC/Buddy track windows
Buddy track requires an optional Northstar DSC
VHF radio to be installed. Buddy track tracks other
boats which have DSC radios connected to their
GPS receivers by NavBus and are in VHF range.
For information on setting up and using the VHF
radio for buddy track, see the radio’s operation
manual.
To go to the DSC/Buddy track windows, press
, select More, then select DSC. Then from
the DSC/BuddyTrack window press
or
to
select one of the three displays: Distress, Poll or
Buddy track.
If there are more items than will fit on the display,
press
or
to see the others.
16-1 The displays
Distress
Boats that have sent DSC
distress messages and their
positions.
Poll
Buddy track
Boats you have manually polled
on the VHF radio, and their
position at that time.
Buddy boats from your DSC
radio. The radio regularly calls
the boats and updates their
positions.
When your DSC radio receives a distress
message, the 657 creates a distress waypoint
at the boat position. Distress waypoints have
default names like DSTRSS01. The 657 displays a
Distress warning.
Select:
OK to return to what you were doing.
Display to switch to Chart and display the
position of the boat sending the distress
message.
Northstar Explorer 657 Installation and Operation Manual
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Boat positions
The boat positions on the 657 can differ from the
true boat positions:
Polled boats: The position is where the boat
was when you last polled the boat.
Distress: The position is the distress waypoint,
which is where the boat was when it sent the
distress message.
Buddy track: The position is where the boat
was when your radio last polled the boat.
16-2 Using the displays
Displaying a boat on the chart
1
Press
or
to select a boat.
2
Press
and select Display. The 657
B
switches to chart window, with the selected
boat position in the middle (see Boat
positions above).
Going to a boat
1
Press
or
to select a boat.
A
2
Press
and select Goto. The 657 starts
navigating to the boat’s position (see Boat
positions above).
On a chart window:
Creating a waypoint
Polled and buddy track boats are not waypoints.
To create a waypoint at the position of a polled
boat (see Boat positions above):
A
B
Distress boats are distress waypoints
Buddy track boats are buddy symbols
1
2
Press
Press
or
to select a boat.
Deleting a boat
At the Distress or Poll displays:
and select Create
waypoint. Edit the waypoint data if
required (see section 5-2-7).
1
2
Press
Press
or
to select a boat.
and select Delete. The boat
Editing a waypoint
is deleted from that display. Delete any boat
waypoint manually (see section 5-2-5).
A distress message creates a waypoint for the
boat or you can create a waypoint at a polled
boat’s position. To change the data of these
waypoints:
Buddy track boats automatically disappear from
the Buddy track window when your DSC radio
can not pick up their signal.
1
2
Press
Press
or
to select a boat.
Deleting all boats
At the Distress or Poll displays:
and select Edit waypoint.
Edit the waypoint data if required (see section
5-2-7).
1
2
Press
Press
or
to select a boat.
and select Delete all. All
boats are deleted from that display and any
boat waypoints are deleted.
58
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
17 Setting up the 657
The 657 has a number of advanced features
which are set up through the setup menu. We
recommend that you become familiar with the
operation of the unit using the default settings
before making any changes in these menus.
To go to a setup option menu, press
twice, then select an option.
Note:
1
2
3
The Setup menu options are explained in the
following sections.
Section 2-1 describes how to set or change
data in the setup menus.
The setup data available will depend on the
optional sensors and instruments installed.
Northstar Explorer 657 Installation and Operation Manual
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup option menus
Factory default settings are shown. The setup data
available will depend on the optional sensors and
instruments installed.
System (see 17-1)
Chart (see 17-2)
Sonar (see 17-3)
General, Water, Land and
Other submenus (17-2)
GPS (see 17-4)
Fuel (see 17-5)
Track (see 17-6)
AIS (see 17-7)
Logs (see 17-8)
Alarms (see 17-9)
Units (see 17-10) Comms (see 17-11)
SmartCraft™
(See the SmartCraft™
Gateway Installation
and Operation Manual)
Calibrate (see 17-12)
Time (see 17-13)
Favorites (see 17-14)
Simulate (see 17-15)
60
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
17-1 Setup > System
•
•
The number of waypoints, routes and tracks
you have stored.
Press
twice, then select System:
Connector wiring information.
In the unlikely event of having to contact a
Northstar dealer for service, quote the software
version number and date.
Language
Select the language for the displays.
Tip: In case you can’t read the current
language, the language setting is found at the top
of the system menu.
Backlight
Select the backlight level for the keys and display
Sonar
(see also section 2-3)
Disable any sonar transducer and disable sonar
functions.
Night mode
Night mode sets the palette for all displays.
A sonar transducer is fitted. Enable sonar
operation.
Normal palette, for daytime
All displays have a palette optimised for night
time.
See section 18-6.
SmartCraft™
No SmartCraft™ gateway is fitted. Disable
SmartCraft™ functions.
See also section 2-3. To change only the chart
palette, see section 17-2.
Key beep
SmartCraft™ gateway is fitted. Enable
SmartCraft™ operation.
Enables or disables the beep when a key is pressed.
Auto power off
See section 18-8.
See section 2-2.
AIS
Factory reset
No appropriate AIS receiver is fitted. Disable
This option returns all of the 657 settings (except
the language, waypoints and routes) to the default
factory settings shown on the setup menus.
AIS.
An appropriate AIS receiver is fitted.
Enable AIS.
See section 17-11.
About window
The about window shows:
Buddy track
•
•
•
The software version and date.
The world chart version.
Any card fitted.
No DSC VHF radio is fitted. Disable Buddy track.
A DSC VHF radio is fitted. Enable Buddy track.
See section 18-8
Northstar Explorer 657 Installation and Operation Manual
61
Download from Www.Somanuals.com. All Manuals Search And Download.
17-2 Setup > Chart
Course up:This option is only available
if the boat is navigating to a destination. The
chart is rotated so that the plotted course to
the destination is vertical.
Press
twice, then select Chart:
Palette
Select the color scheme for the LCD display.
The options are:
Normal
Sunlight: Brighter colors, more visible in
sunlight.
Night: Reversed colors for night, to preserve
night vision.
Map datum
657 GPS positions are based on a worldwide
reference (datum) known as WGS 84. Most paper
charts are based on WGS 84. However, some
paper charts are based on other datums In these
cases, the latitude and longitude coordinates of
objects on the 657 chart window are different
to the latitude and longitude coordinates of
these objects on the paper chart. This applies to
all objects, such as the boat, waypoints, tracks,
lines of latitude and longitude and cartographic
features such as land, rocks, buoys and depth
contours.
Use Map datumto select the 657 map datum
to match the datum of the paper chart. Then, the
latitude and longitude coordinates of objects
displayed on the 657 will change to match the
corresponding coordinates on the paper chart.
Setting map datum
1
2
3
In the Chart setup menu, select Map
Rotation
The options for chart rotation are:
datum.
Select the map datum for the paper chart you
are using.
North up: North is always at the top of the
chart window.
If you select a datum other than WGS 84
the 657 asks if you want to apply the NMEA
datum offset (see below).
Track up: The chart is rotated so that the
boat direction is to the top of the display.
This option is useful for navigating narrow
harbours or rivers. The 657 asks for a course
deviation resolution; this is how much the
boat direction needs to change to make the
chart redraw.
!
WARNING
When you change to a chart with a different
datum, change the 657 map datum again.
Tip: If the chart redraws too
frequently, increase the course deviation
setting.
62
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Some charts have consistent position errors. To
correct this, apply a map shift. After a map shift:
NMEA datum offset
If you select a map datum other than WGS 84,
the map datum offset can be applied to latitude
and longitude coordinates sent on the 657 NMEA
output:
The positions of cartographic features (such
as land, rocks, buoys and depth contours)
move on the 657 chart window to where they
should be.
Latitude and longitude coordinates
displayed on any NMEA repeater do not
match the coordinates on the 657. Latitude
and longitude coordinates broadcast on any
NMEA VHF transmitter will be the same as the
coordinates on a WGS 84 chart.
The positions of the boat, waypoints, tracks,
and lines of latitude and longitude on the 657
chart window remain unchanged.
Applying a map shift
1
2
3
Move the boat to a known point on the chart,
for example a marina berth.
Latitude and longitude coordinates
displayed on any NMEA repeaters match the
coordinates on the 657. However, latitude
and longitude coordinates broadcast on any
NMEA VHF transmitter will be slightly offset
from coordinates on a WGS 84 chart.
In the Chart setup menu, select
Map shift.
Move the cursor to the position on the chart
where the boat actually is.
4
5
Press
and select Set.
to set the new map shift.
Map shift
Press
The boat will now be displayed at its
actual location.
!
WARNING
Map shift is for eliminating minor offsets.
It should not be used if the correct datum
is available. Use map shift with caution:
incorrect application will cause incorrect boat
positions.
Clearing the map shift
Clearing the map shift removes any map shift
from the cartographic features on the 657 chart
window.
1
In the Chart setup menu, select
Map shift.
2
3
Press
and select Clear.
Press
.
General submenu
Plotter mode
Normal: only scales available on the chart card can be displayed
If you press or to select a chart scale which is not available, on the chart card, the
chart window will change to this scale but will only display the boat position and track (if enabled).
The rest of the display is white with black crosshatch lines and no chart information is displayed. This
is useful to zoom to a small scale to track small boat movements or if there is no detailed chart for
an area
Mixing levels
Anticlutter
Mixes lower detail charts with higher detail charts on chart boundaries
Lower detail chart is not shown
Lower detail chart shown; this is slower to redraw
Names and icons shown. Note: this is independent of the change in detail shown at different
zoom levels
Hides some less important names and icons to make the chart clearer
Value added data
Non marine chart data shown
Northstar Explorer 657 Installation and Operation Manual
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Projected course
The 657 can estimate the course after a given time, based on the current speed and heading (see
section 3-4). The options are 2 minutes, 10 minutes, 30 minutes, 1 hour, 2 hours or Off
CDI scale
See Appendix C. The options are 0.05, 0.1, 0.2, 0.5, 1.0, 2.0, 4.0 and 10.0 distance units
Displays a latitude and longitude grid
Lat/lon grid
Boundaries
Displays boundaries around areas where more detailed chart coverage is available:
Autoshows the next four detail levels; On shows all
Text/icon size
Water submenu
Water features
Select the size of chart text and icons
Displays marine sediment labels (for example, M shows areas of mud) and tide station icons
Bathymetrics
Displays underwater depth contours between Bath & sndgs min and max
Spot soundings
Displays depth soundings between Bath & sndgs min and max
Bath & sndgs min
Bath & sndgs max
Tidal flow
The minimum depth for Bathymetrics and Spot soundings
The maximum depth for Bathymetrics and Spot soundings
Displays dynamic tide flows: arrows on a chart showing the present tide stream and
orientation (requires a GPS fix and an NT-MAX card)
Land submenu
Land features
Displays land features, for example regions, rivers, roads, railways, airports
Displays land contours, shaded like depths (requires an NT Max card)
Land elevation
Other submenu
Waypoints
Displays waypoints: Hide all only displays waypoints on any selected route; Selected
displays waypoints with their display option set to Icon or I+N (Icon and Name) (see section 5)
Names
Lights
Displays place names
Light House display options: Off hides all light indicators (the icon still shows); No sectors hides
sectors; On shows sectors; Animated activates light animation.
Note: with light animation enabled sectors are not visible, animation only operates in single
chart view or in the top chart of chart + chart
Nav-aids
Displays signals (fog, radar, radio stations) and bouys. Int and US select the icon format;
Smpl draws simpler icons
Attention areas
Displays attention area boundaries and information icons ; attention areas are important
areas, such as restricted anchorages or shallow areas
64
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
17-3 Setup > Sonar
Press
twice, then select Sonar:
Fish sensitivity
Selects the minimum strength fish echo that will
be displayed as a fish symbol. Higher values will
display more fish symbols.
Digit size
Use this to remove or change the size of the
depth window on the sonar displays. There is a
choice of: Small, Mediumand Large.
Palette
Use this to select a color palette. Each color
within the palette represents a different echo
strength, as shown on the sonar displays.
There is a choice of five color palettes: Black,
Blue, White, Vividand 8 color. The first
four pallettes display more detail, and each color
covers a 1.5 dB signal range. The 8 color
palette displays less detail, and each color covers
a 3 dB signal range.
Frequency
There is a choice of: 200 kHz, 50 kHzand
Mixed. For information about selecting a
suitable frequency for the water conditions. (see
section 8-3)
Interference filter
Scroll speed
No filter, normal setting.
Use this to set the scroll speed on the display.
There is a choice of: Very Fast, Fast,
Medium, Slowand Pause.The depth of the
water also affects the speed of the display.
Filters the echo signal to remove spiky
interference such as engine noise or depth
sounders on nearby boats.
Noise filter
Faster scroll speeds combined with a slow
boat speed (typically between 2 and 6 knots)
shows the most fish detail. Mediumor Slow
scroll speeds result in sonar information being
displayed over a longer period, but with less
detail (see Section 8-2).
Averages the echo signal to remove rapid
changes. Select Meduim or High to give a
smoother bottom trace–this may help to detect
a deeper bottom; however these settings may
also remove fish echoes. Select Off for best
fishfinding.
Fish symbols
Pulse length
The 657 always displays echoes from fish (fish
arches, see section 8-4). If fish symbols are on, a
symbol is displayed over the arch (see section
8-4). The options are:
This can be used to specify the length of the
transmitted ultrasonic pulse. A short pulse length
improves the display detail but contains less
energy, therefore it does not penetrate as deeply
into the water as a longer pulse.
• Off: No fish symbol is displayed.
• Funor Normal: A fish symbol is displayed.
There is a choice of Auto, Short, Medium or
• Fun + depthor Normal + depth: A
fish symbol is displayed and the depth shown
beside the fish symbol.
Long. The Auto setting is recommended.
Pulse power
This can be used to specify the power output
of the transmitted ultrasonic pulse. Low power
output conserves the battery and produces a
clear display in shallow water.
Fish filter
Use this to select the minimum fish size that will
be displayed as a fish symbol and to trigger the
Fish alarm. The options are: Small, Medium
and Large.
There is a choice of Auto, Low, Medium or
High. The Autosetting is recommended.
Northstar Explorer 657 Installation and Operation Manual
65
Download from Www.Somanuals.com. All Manuals Search And Download.
17-4 Setup > GPS
shows the status of the GPS receiver (see section
7). Restart the GPS if the receiver has not been
used for some time and is taking a long time to
get a GPS fix.
Press
twice, then select GPS:
Static Navigation
When the boat stops or moves very slowly, the
calculated GPS speed and course become erratic.
Static navigation allows the erratic values to be
filtered:
•
0.01 to 99.9: If the boat speed is slower than
this, the speed is displayed as zero and the
course stays unchanged.
GPS Source
• NMEA: Use the external GPS antenna
supplied or an external GPS or DGPS source
connected via NMEA (see section 18-10).
•
0 (Off): The calculated speed and course are
always used.
• NavBus: Use an external GPS or DGPS source
Speed and Course Filter
connected via NavBus (see section 18-9).
Waves and wind cause the boat speed and
course to fluctuate slightly. To give stable
readings, the 657 calculates these values by
taking several measurements and averaging
them.
DGPS Source
Enables or disables the satellite based DGPS
correction (see section 7). The options are None
or WAAS/EGNOS. Do not enable WAAS/EGNOS
outside their coverage areas or the accuracy of
the position might be degraded.
A lower value averages measurements over
a shorter period of time. This gives the most
accurate value but has the most fluctuations.
WAAS covers all of the USA and most of Canada.
To use WAAS, the GPS antenna must have a clear
view of the sky towards the equator. EGNOS will
cover most of Western Europe when it becomes
operational.
A higher value averages measurements
over a longer period of time. This gives the
most stable value but will ignore some [true]
sudden speed changes.
Set the Speed and Course filters to the lowest
values which give stable readings. The range of
each filter is 1 to 60 seconds or Off (0).
Restart GPS
Restarts the internal GPS receiver for servicing
or troubleshooting. The GPS receiver takes up
to three minutes to restart. The satellite window
17-5 Setup > Fuel
!
WARNING
Fuel consumption can change drastically
depending upon the boat loading and the
sea conditions. Always carry adequate fuel for
the journey, plus a reserve.
Fuel functions require optional fuel flow sensors to
be installed. Press
twice, then select Fuel:
66
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Source
Setup tanks
Select the fuel flow sensors to use if the boat has
more than one set of fuel sensors. Normally select
Auto.
If the boat has more than one tank, select Tank and
select each tank in turn.
For the selected tank, you can enter:
Num engines
Set the number of engines, or select 0to disable
the fuel functions. If there are two engines they are
called port and starboard.
Num tanks
Set the number of fuel tanks. If there are two tanks
they are called port and starboard.
Setup engines
Add fuel, Fill tank, Set remaining:
If the boat has more than one engine, select Engine
and select each engine in turn.
See section 12-3.
Tank alarm: See section 12-4.
For the selected engine, you can enter:
Tank size: The tank capacity. Northstar
recommends measuring tank size by draining
the fuel tank, filling it to capacity and using the
fuel dispenser’s reading. Beware of air pockets,
especially in underfloor tanks.
Fuel consumption curve
See section 10-6.
Speed source
If both water speed and ground speed are available,
select which to use for fuel calculations (see section
10-5-1).
From tank: The fuel tank the engine is connected to.
Flow filter: Most engines do not draw fuel from
the tank at a steady rate. To give a stable fuel flow
reading, the TRACKER calculates the flow by taking
several measurements and averaging them. Use the
Flow filter to set the period over which the fuel flow
is averaged.
Max fuel flow
The maximum fuel flow from a fuel tank to be
displayed on an analog fuel flow gauge (see section 8)
The Flow filter can be set from 0 to 30 seconds. Use
the lowest value which gives a stable flow.Usually
a value of 5 to 10 seconds will give a satisfactory
result for two-stroke carburettor engines. Fuel
injected or four-stroke engines may require a larger
value.
This setting affects the Fuel flow and Fuel economy
reading on the Fuel window but it does not affect
the Fuel used reading.
Northstar Explorer 657 Installation and Operation Manual
67
Download from Www.Somanuals.com. All Manuals Search And Download.
17-6 Setup > Track
Press
twice, then select Track:
Plotting Interval
Select the plotting and recording interval. The
options are Distanceor Time.
Distance
Select the distance plotting interval: 0.01, 0.05, 0.1,
0.5, 1.0, 2.0, 5.0 or 10.0 distance units.
Time
Select the time plotting interval: 1, 5, 10 or 30
seconds or 1 minute.
Memory used
The percentage of memory used in the track
being recorded.
Tracking records and displays the boat’s course
on the chart (see section 3-5). Five different tracks
can be recorded: track 1 has up to 2000 points
and tracks 2, 3, 4 and 5 have up to 500 points
each.
Tip: Use the user card window to check the
number of points recorded in each track
(see section 14).
Send track
Record
This option is included for compatibility with
older units. For information, see your Northstar
dealer.
Off: The 657 stops recording a track.
1 to 5(select a track number): The 657
starts recording the boat’s course into the
selected track.
Delete track
The data in the track selected for Record (see
DisOpflafy: No track is shown on the chart.
above) is deleted.
1 to 5(select a track number): The
selected track is shown on the chart.
68
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
17-7 Setup > AIS
Note: This feature requires an AIS receiver.
Show Dangerous Only
Show vessels that have a TCPA/CPA below the
trigger values. This filter will override any other
filter option.
Dangerous Vessel Alarm
When enabled an alarm will activate when both
the TCPA and CPA is less than the trigger values.
Even when this setting is disabled the dangerous
vessels will still be indicated on the chart.
TCPA Limit
There are multiple methods to filter AIS vessels
that are displayed onto the charts.
Set the Time of Closest Point of Approach limit.
CPA Limit
Set the Closest Point of Approach limit.
Filter by distance
Vessels outside the radius selected from our
current position is filtered off the chart. Default
value is set to 300 nm allowing all vessels to be
displayed onto the chart within that distance.
Projected Course
Show the estimated course of all vessels based on
their current SOG and COG.
Filter by speed
Vessels with speed below value selected by user
is filtered off the charts. Default is set to 0 kn
allowing all vessels to be displayed onto the chart.
17-8 Setup > Logs
Press
twice, then select Logs:
Reset trip dist
This resets the trip distance to zero.
Reset total dist
This option resets the total distance to zero.
Reset engine hours
Use this option to reset the engine hours to
zero. This can be useful after an engine service
or to count the engine hours between service
intervals.
The values can be reset independently of each
other. These log values are saved when the unit
is turned off.
Northstar Explorer 657 Installation and Operation Manual
69
Download from Www.Somanuals.com. All Manuals Search And Download.
17-9 Setup > Alarms
Press
twice, then select Alarms:
All alarms except Loss of GPS fix can be
turned on (enabled) or off (disabled).
For all alarms select to turn the alarm on or
select to turn the alarm off.
For most alarms there is a trigger value. The
alarm will sound each time the alarm value equals
the trigger value. For example, the Danger
alarm will sound if the boat comes closer to a
danger waypoint than the trigger value and the
Anchoralarm will sound if the boat moves by
more than the trigger value.
Icons for alarms that are on can be displayed in
the data header (see section 2-7-3). An alarm icon
is normally black and turns red when the alarm
sounds.
Symbol Alarm
Arrival radius
Alarm sounds when it is on and the:
Boat is closer to the destination or to a waypoint than the alarm
trigger value
Anchor alarm
XTE
Boat moves by more than the alarm trigger value
Boat moves off course by more than the CDI scale (see section 14-2)
Boat comes closer to a danger waypoint than the alarm trigger value
657 can not receive the DGPS signal (beacon, WAAS or EGNOS)
657 can not receive the GPS signal (this alarm is always on
Danger
Loss of DGPS fix
Loss of GPS fix
Loss of
AIS receiver
communication
657 is no longer receiving communication from the AIS receiver
(Alarm is on when AIS is enabled)
Fish
Echo matches the profile of a fish
Too shallow
Too deep
Temperature
Depth is less than the alarm trigger value
Depth is greater than the alarm trigger value
Temperature equals the alarm trigger value
Temperature rate Rate of change of temperature equals the alarm trigger value
Low battery
Low fuel
Battery voltage is less than the alarm trigger value
Fuel remaining equals the alarm trigger value
70
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
17-10 Setup > Units
Press
twice, then select Units:
Height
ft (feet) or m (metres)
Fuel
Litres, USGal (US gallons) or ImpGal (Imperial
Gallons)
Compass
°T (True north) or °M (Magnetic north)
Temperature
°F (Fahrenheit) or °C (Celsius)
Wind (optional)
Requires a wind instrument: True or App
The default units are shown above.
(Apparent)
Note: that the units for wind speed are the speed
units.
Distance
nm (nautical miles), mi (miles) or km (kilometres)
Pressure
Requires SmartCraft™: kPa or psi
Speed
kn (knots), mph (miles per hour) or kph
Baro (Barometric pressure)
(kilometres per hour)
Requires a Northstar VHF receiver with barometer
connected by NavBus: InHg or mB.
Depth
ft (feet), m (metres) or fa (fathoms)
17-11 Setup > Comms
Use this feature when the 657 is connected to
other Northstar instruments through NavBus or
any compatible NMEA instrument.
Lat/lon dps
Select the number of decimal points used for
latitude and longitude transmitted in NMEA
sentences.
Press
twice, then select Comms:
NavBus
NavBus is the preferred method for connecting
the 657 to other Northstar instruments. Select this
if the instruments are connected using NavBus.
NavBus Group
Use this when a group of Northstar instruments
are connected together using NavBus, to specify
a group of instruments for backlighting, if
required. Then, if the backlight setting on one
instrument in the group is adjusted, the other
instruments change automatically. Otherwise,
select 0. See section 18-9.
NMEA out
NMEA is generally used with third party
instruments (see section 18-10). Select this to
transmit NMEA sentences, for example to an
autopilot.
NMEA data
Use this to specify which NMEA sentences will be
transmitted (see section 18-10 and Appendix A).
Northstar Explorer 657 Installation and Operation Manual
71
Download from Www.Somanuals.com. All Manuals Search And Download.
17-12 Setup > Calibrate
Press
twice, then select Calibrate:
Speed filter
Waves and wind cause the boat speed from the
paddlewheel transducer to fluctuate slightly. To
give stable readings, the 657 calculates these
values by taking several measurements and
averaging them. Set the Speed filter to the lowest
value which gives stable readings. The range is 1
to 30 seconds or Off (0).
Temperature
Speed
The factory settings should be sufficiently
accurate for normal usage. To calibrate the
temperature readout, first measure the water
temperature with a thermometer known to be
accurate.
This calibrates the speed from a paddlewheel
sensor connected to the 657. Calibration may
be required because different hull shapes have
different flow characteristics. Obtain an accurate
measurement of the boat’s speed from a GPS
receiver; or by following another boat travelling
at a known speed; or by making a timed run over
a known distance.
Use the cursor keys to display the temperature
readout box, then increase or decrease the
value to match the measured temperature. The
temperature can be set from 32° to 99.9°F (0° to
37.7°C) with a resolution of 0.1° unit.
Note: for accurate calibration:
•
The speed from a GPS receiver should be
greater than 5 knots.
To change the units between °F (Fahrenheit) or °C
(Celsius). (see section 17-10).
•
The speed from another paddlewheel
transducer should be between 5 and 20
knots.
Temperature filter
Water turbulence and currents cause the water
temperature to fluctuate slightly. To give stable
readings, the 657 calculates these values by
taking several measurements and averaging
them. Set the Temperature filter to the lowest
value which gives stable readings. The range is 1
to 30 seconds or Off (0).
•
Best results are achieved in calm conditions
where there is minimal current (best at high
or low tide).
Calibrating speed:
1
2
3
Travel at a constant, known speed.
In the Calibrate menu, select Speed.
Press
to the true value.
Press
or
to change the displayed speed
4
.
72
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Keel Offset
A depth transducer measures depths below
where the transducer is mounted on the boat,
usually the bottom of the boat. The 657 calculates
the depths to display by adding the keel offset to
all measured depths.
Transducer;
A
B
depths measured
below here
A
Have a zero keel offset to display depths
below the transducer.
Depths measured
below here
B
Enter a positive keel offset to increase the
displayed depth. For example to display the
total depths below the surface, enter the
depth of the transducer below the surface.
C
Enter a negative keel offset to decrease the
displayed depth. For example, to display the
depths of clear water below the boat, enter
minus the depth of the deepest part of the
boat below the transducer.
C
Depths measured
below here
Speed range
Fuel
The maximum reading to display on an analog
boat speed gauge (see section 10). Choose a
range suitable for your boat.
See section 12-7, Calibration.
17-13 Setup > Time
Press
twice, then select Time:
1
2
Select Local offset.
Press
press
or
to change the offset, then
.
Time format
The options are 24 hour or 12 hour.
Local offset
Date format
The options are dd/MMM/yy, MMM/dd/yy,
dd/MM/yy or MM/dd/yy.
The difference between local time and UTC
(GMT). Change local offset when daylight saving
time starts and ends. The range is 0 to 13 hours,
in 30 minute steps.
17-14 Setup > Favorites
See section 2-7-2
Northstar Explorer 657 Installation and Operation Manual
73
Download from Www.Somanuals.com. All Manuals Search And Download.
17-15 Setup > Simulate
Simulate mode is a way of becoming familiar with
the 657 (see section 2-6).
1 Normal
Simulates the boat moving from the selected
start point at the given speed and heading. The
options required for Normal are:
Press
twice, then select Simulate:
Speed: The simulated boat speed to use.
Course: The simulated course over ground.
Note: To select the start point, go to the chart
window before starting the simulation. Then:
•
To start the simulation from the boat position,
press
to switch to center on boat
mode.
Simulate
•
To start the simulation from a different point,
move the cursor to that point on the chart.
Turn simulate mode off
Turn simulate mode on
Tip: To calculate a course, use the cursor (see
section 3-3).
!
WARNING
Tip: As the boat moves, vary Course to
simulate the boat moving off course.
Never have simulate mode on when the 657 is
navigating on the water.
2 Demo
Simulates a boat moving along a route and
automatically displays different 657 functions.
The options required for Demo are:
Mode
There are two choices for Mode:
Speed: The simulated boat speed to use.
Route: The route to follow.
18 Installation
Correct installation is critical to the
performance of the unit. It is vital to read
the entire installation section of this manual
and the documentation that comes with the
antenna and any other units before starting
installation.
CAUTION
Do not mount any part where it can be used as a
hand hold, where it might be submerged or where
it will interfere with the operation, launching or
retrieving of the boat.
To help ensure proper operation, do not mount
any part or cable within 0.5 m (20”) of the plane of
a radar antenna or within 1 m (3 ft) of a compass
or source of electrical noise, such as engines,
fluorescent lights, and power inverters.
!
WARNING
Ensure that any holes cut are in a safe
position and will not weaken the boat’s
structure. If in doubt, consult a qualified
boat builder.
When fitting a cable, do not crush or strain the
cable. Secure the cable at regular intervals. Ensure
no connectors or exposed terminals are in wet
area.
If the cables supplied are too long, do not shorten
the cable; instead coil the cable. Most cables can
be extended with Northstar extension cables. Do
not fit more than one extension cable.
74
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
18-1 Installation: What comes with the 657
657 display unit, with a holder for plug-in cards and blanking cap for fuel connector.
Dust cover for display unit
Power cable
Mounting bracket (screws included)
GPS connection cable
Warranty registration card
Northstar 124 GPS antenna
Flush mounting kit
Dual frequency transom sonar transducer (includes cable kit and screws)
Transom Mount Transducer Installation Manual
Full Instruction Manual CD
18-2 Installation: Options and Accessories
•
•
•
Replacement paddle wheel
Fuel sensors: For fuel functions. The 657 can use
these optional fuel flow sensors, fitted to one or
two engines:
C-MAP™ NT-MAX, NT+ or NT chart cards.
C-MAP™ user cards (3 V) for storing data. (The
older 5 volt cards are not supported)
•
Northstar petrol/gasoline sensors (see
section 18-7)
•
•
Northstar carry bag.
•
SmartCraft™ fuel sensors (see section 18-10)
Northstar NavBus junction boxes simplify
wiring, particularly if several instruments are
connected. For more information, see the
NavBus Installation Manual.
DSC VHF radio: Tracks other boats with GPS
receivers and DSC radios and displays barometric
pressure (see section 18-8).
SmartCraft™: With one or two SmartCraft™
capable Mercury petrol/gasoline engines, the 657
can display engine data and trim and can control
troll speed (see section 18-10).
Optional sensors and instruments
External alarms: Lights or sounders in the boat
to sound alarms through the boat (see section
18-4).
Other instruments: The 657 can receive data
from other instruments and send data to other
instruments by NavBus or NMEA (see sections
18-11 and 18-12).
GPS or DGPS antenna: For GPS navigation (see
section 18-5).
Sonar transducer: For depth sounding and fish
finding (see section 18-6).
Please consult your Northstar dealer for more
information.
Northstar Explorer 657 Installation and Operation Manual
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Power (18-4)
External alarms (18-4)
Display unit
(18-3)
NavBus instruments (18-9) and VHF
radio (18-8)
NMEA out to instruments (18-10)
Black
GPS antenna (18-5), Petrol/gasoline
sensors (18-7), NMEA in (18-10)
Yellow
Blue
Sonar transducer (18-6)
Power/data cable
Pin Wire
Function
1
Black
Ground: - power in, NMEA ground. (The cable has two black wires which are
connected inside the cable and it does not matter which black wire you use)
2
3
4
5
6
7
8
Brown
White
Blue
Not used
NMEA out
NavBus-
Red
Power in, +10.5 V DC to +30.5 V DC
Orange NavBus+
Yellow
Green
Auto power in
External alarm out, 30 V DC 200 mA maximum.
76
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
18-3 Installation: The display unit
Select a position for the display unit:
•
•
Not exposed to the direct sun or water and
protected from physical damage during
rough sea passages.
•
At least 4” (100 mm) away from the compass,
at least 12” (300 mm) away from any radio
transmitter and at least 4 ft (1.2 m) away from
any antenna.
Easy to access the power source and
convenient to route the transducer cables.
•
Easy to read and operate. If possible, mount
the display unit in front of the navigator or to
the right of the navigator because the LCD
display is more readable from these positions.
There are two mounting arrangements:
1 Flush Mounting
2 Bracket Mounting
Requires a solid panel with access behind
for wiring and mounting screws. After flush
mounting, the display unit cannot be tilted or
moved after installation to reduce any unwanted
glare or reflections. Carefully select the best
viewing position before installation. This would
generally be in a shaded area.
Requires a panel for mounting the bracket. Ensure
that the panel is not likely to deform and is not
subject to excessive vibration. The bracket can
be tilted and rotated. The display unit can be
removed when it is not in use.
1
Hold the bracket in place and mark the screw
holes.
1
2
3
4
Cut a hole in the bulkhead for the display unit
using the flush mount template.
2
Drill the screw holes and screw the bracket in
place. Do not overtighten the screws or the
display unit might not rotate.
Drill four holes for the mounting studs using
the flush mount template.
3
Hold the display unit in place on the
mounting bracket shaft. Hand tighten the
knob on the mounting bracket.
Screw the four studs into the brass inserts in
the back of the display unit.
Sit the display unit in place and fit the
washers and nuts to the studs.
Mounting bracket
Knob
Northstar Explorer 657 Installation and Operation Manual
77
Download from Www.Somanuals.com. All Manuals Search And Download.
18-4 Installation: Power/data cable
The power/data cable has a black locking collar and flying leads.
1
Wire the 657 for auto power to have the 657 turn on with the boat’s ignition switch or to to record
engine hours or if the 657 must add up the total fuel used (for example if Northstar petrol/gasoline
fuel sensors are installed or if SmartCraft™ is installed without fuel tank level sensors). Otherwise wire
for basic power (for more information, see section 2-2).
Basic power
Power/data cable
Red
Fuse 2A
Black
Yellow
Black
Main switch
12/24 V DC
Auto power
During setup, set up Auto power off(see sections 2-2 and 17-1)
Power/data cable
Yellow
Ignition
Fuses 2A
Ignition switch
Main switch
12/24 V DC
Black
Red
Black
2
3
Wire any external alarm beepers or lights. The
alarm output switches to ground to sound
the alarm. If the current is more than 200 mA,
fit a relay.
Power/data cable
Red
Green
Connect the power/data cable to the black
display unit connector; turn the collar to lock
the connector.
Black
External beepers or
lights
78
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
18-5 Installation: GPS antenna
Restart GPS:
Selecting an antenna
Restarts the GPS receiver, satellite reception will
be lost until the receiver completes its restart and
acquires the satellites.
Fit one of these GPS antennas:
•
•
Normally use the GPS antenna supplied.
An optional differential beacon DGPS
antenna to give enhanced accuracy within
range of land based differential beacons
in areas where WAAS or EGNOS are not
available. Such a DGPS antenna has both a
GPS receiver and a beacon receiver, and it
automatically applies the beacon correction
to the GPS position.
!
WARNING
MOB will not work if the Instrument does not
have a GPS fix.
Select restart GPS and press
Installing an antenna
•
A compatible GPS or DGPS instrument or
antenna connected by NavBus (see section
18-9) or NMEA (see section 18-10). In this case,
the 657 does not need its own antenna.
If an external antenna is required, install the
antenna and fit the antenna cable back to the
display unit. Follow the instructions in the manual
supplied with the antenna. Fit an optional
Northstar extension cable if required.
Note:
To configure the 657 for different antenna
options, see section 17-4.
•
If a SmartCraft™ system or Northstar petrol/
gasoline sensors are fitted as well, fit a AIS cable:
For more information, contact your Northstar
dealer.
GPS antenna
Yellow
Yellow
DGPS Source:
GPS/fuel AIS cable
White
Enables or disables the satellite based DGPS
correction (see section 7). The options are
None or WAAS/EGNOS. Do not Enable
WAAS/EGNOS outside their coverage areas or the
accuracy of the position might be degraded.
Other connections
Otherwise:
WAAS covers all of the USA and most of Canada.
To use WAAS, the GPS antenna must have a clear
view of the sky towards the equator. EGNOS will
cover most of Western Europe.
Yellow
GPS antenna
During setup, configure the 657 for the chosen
antenna, see section 17-4.
Northstar Explorer 657 Installation and Operation Manual
79
Download from Www.Somanuals.com. All Manuals Search And Download.
18-6 Installation: Sonar transducer
Either:
!
WARNING
•
Fit the transom mount sonar transducer
supplied, following the instructions in the
Transom Mount Transducer Installation
Manual supplied with the 657.
Do not install plastic through hull transducers
in solid wooden hulls. Leakage through the
hull may result.
•
For enhanced performance, fit an optional
through hull dual frequency sonar transducer
and through hull speed/temperature
transducer. Contact the nearest Northstar
dealer for more information.
Do not install bronze transducers in metal
hulls. This will cause electrolytic corrosion that
may result in damage to the hull or transducer.
Connect the transducer to the blue 657
connector; tighten the locking collar.
During setup
Sonar cable
Blue
a
set Sonarto (see section 17-1)
set up the sonar options (see section 17-3)
b
18-7 Installation: Northstar petrol/gasoline sensors
Fit the optional petrol/gasoline fuel kit following
the instructions supplied with the kit.
GPS antenna (optional)
Note:
Yellow
Yellow
SmartCraft™ engines have fuel flow sensors,
therefore Northstar fuel sensors are not
required as well.
GPS/fuel AIS cable
White
For dual engines, fit two kits.
Fuel sensor cable
Wire the 657 for auto power (see section
18-4).
During setup:
An optional GPS/fuel AIS cable is required.
a
set up Auto power off (see sections 2-2 and
17-1)
b
set the fuel data (see section 17-5)
80
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
18-8 Installation: SmartCraft™
If the boat has one or two SmartCraft™ capable
Mercury petrol/gasoline engines, connect the
657 to the SmartCraft™ engines with an optional
SmartCraft™ gateway. The display unit can display
engine data and trim and can control troll speed.
GPS antenna (optional)
Yellow
Yellow
GPS/fuel AIS cable
White
Note:
Fit a single gateway for single engines and a
dual gateway for dual engines.
SmartCraft™ engines have fuel flow sensors,
therefore Northstar fuel sensors are not
required as well.
SmartCraft™ gateway
An optional GPS/fuel splitter cable is required.
Enter the SmartCraft™ setup data. For information
on installing, setting up and using SmartCraft™,
see the SmartCraft™ Gateways Installation and
Operation Manual.
If the fuel tank does not have SmartCraft™
level sensors, wire for auto power (see section
18-4).
18-9 Installation: Other NavBus instruments
NavBus is Northstar’s system for connecting
instruments together to interchange data
and share transducers. When instruments are
connected by NavBus:
NavBus and the 657
The 657 can:
Display wind speed and direction from an
optional Northstar Wind instrument.
If the units, alarms or calibration are changed
in one instrument, then the values will
automatically change in all other instruments
of the same type.
Receive and display depth from an optional
Northstar depth instrument.
Receive and display boat speed and water
temperature from a paddlewheel sensor on an
optional Speed instrument.
Each instrument can be assigned to a group
of instruments. If the backlight is changed in
an instrument in group 1, 2, 3 or 4 then the
backlight will automatically change in the
other instruments in the same group.
Receive data from an optional Northstar VHF
radio (with NavBus functionality). The 657 can
display:
Baro: barometric pressure
If the backlight is changed in an instrument
in group 0 then no other instruments are
affected.
Baro history: barometer history
Weather: a predication, based on changes in
If an alarm sounds, mute it by clearing the
alarm on any instrument which can display
that alarm.
barometric pressure
Fish forecaster: a prediction based on
changes in barometric pressure
DSC/Buddy Track: (see section 16)
Receive data from an optional GPS or
GPS/DGPS source.
Send data to optional Northstar instruments,
for example to a repeater.
Northstar Explorer 657 Installation and Operation Manual
81
Download from Www.Somanuals.com. All Manuals Search And Download.
During setup for NavBus instruments, set NavBus
to and assign the instrument a NavBus
groupnumber (see section 17-11)
18-9-1 Installation: Northstar VHF radio
Fit and set up the optional Northstar VHF
radio (with NavBus functionality) following the
instructions supplied with the radio.
Black Power/data cable
Orange
Black Power/data cable
Orange
Blue
Blue
Blue
Grey
Other Navbus instrument
Radio data cable
18-10 Installation: Other NMEA instruments
NMEA is an industry standard for interconnecting
instruments. It is not as flexible or as easy to
install as NavBus.
Power/data cable
The 657 can:
White NMEA out
Receive and display wind speed and
direction from an optional compatible wind
instrument.
Black
Black NMEA ground
GPS antenna
Receive and display depth, paddlewheel
boat speed and water temperature from an
optional compatible instrument.
Yellow
Yellow
GPS/fuel AIS cable
White
Receive data from an optional compatible
GPS or GPS/DGPS source.
Send GPS position and other navigation
data to an autopilot or other instrument.
An autopilot requires APB, APA and VTG
sentences (see section 17-11).
White NMEA in
(requires Special
Fuel Cable)
Red AIS data in
Receive data from an optional AIS receiver.
For information on sending NMEA data to the 657,
see your Northstar dealer.
Black and
Shield Ground
During setup to send NMEA data to other
instruments, set NMEA outto and specify
the NMEA datato send (see section 17-11).
82
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
18-11 Installation: Setup and test
Setup and test
5
6
Enter setup data to set up the 657 to your
requirements and to set up any optional
sensors or instruments (see section 17).
1
Put a blanking cap on any unused connector
on the back of the display unit. Ensure all
connectors are plugged in and the display
unit is in place.
At the satellite display, check that it picks
up GPS satellites. Wait for the GPS receiver
to start up and the fix type to change from
‘Acquiring’ to ‘GPS fix’. This should take less
than two minutes (see section 7).
2
If the display unit is bracket mounted, adjust
tilt and rotation for best viewing and hand
tighten the knob.
7
Go on a test run to check that the navigation
equipment works correctly, particularly when
a radio transmitter or radar is used.
3
4
Insert any required C-MAP chart card (see
section 1-3).
Turn the instrument on (see section 2-2).
When the 657 is turned on for the first time, it
displays an installation menu:
i
Select the language to use.
ii Change the data if necessary (see section
2-1)
iii When the setup data is correct, press
.
This data can be changed later
(see section 17).
Northstar Explorer 657 Installation and Operation Manual
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A - Specifications
GENERAL
Transom transducer cable length:
Size: 5.9”H x 6.5”W x 2.6”D
(150mm H x 164mm W x 65mm D)
10 m (33 ft)
Depth acquisition time from startup:
Display: 127 mm (5”) diagonal, TFT color, 480 x
Typically 2 seconds at 30 m (100 ft)
640 pixels.
Temperature:
Backlight: Display and keys
Range 0° to 37.7°C (32° to 99.9°F)
Resolution of 0.1° unit.
Supply voltage
10.5 V DC to 30.5 V DC.
Speed (from paddlewheel transducer):
1 to 96.6 kph (57.5 mph, 50 kn).
Supply current: at 13.8 V
350 mA min - no backlighting.
1A max - full backlighting. ]
FUEL COMPUTER
(Optional fuel sensor(s) required)
External beeper or light output: Switched
to ground to sound alarm, 30 V DC, 200 mA
maximum.
Engine types:
Outboard carburetted two stroke and EFI
petrol/gasoline engines: 50 to 300 hp.
Outboard four stroke petrol/gasoline engines:
90 to 300 hp.
Operating temperature
0°C to 50°C (32°F to 122°F)
Inboard petrol/gasoline engines: 70 to 400 hp.
ALARMS:
Flow rate:
User set: Arrival radius, anchor, XTE, danger,
dangerous AIS vessels, too shallow, too deep,
fish, temperature, temperature rate, low
battery, low fuel (optional), loss of DGPS fix
Minimum: 5 litres per hour (1.3 U.S. gallons per
hour).
Maximum: 130 litres per hour (34 U.S. gallons
per hour).
Fixed: Loss of GPS fix
COMMUNICATIONS
GPS NAVIGATION
NavBus
Chart card: C-MAP™ NT-MAX, NT+ or NT
User card: 3.3 V C-MAP™
Connection to other Northstar instruments.
NMEA
Waypoints: Up to 3000, with default or user-
defined alphanumeric names up to eight
characters.
NMEA 0183 ver 2 4800 baud
Inputs from compatible instruments:
BWR, DPT, GGA, GLL, GSA, GSV, HDG, HDM,
HDT, MTW, MWV, RMC, VHW, VTG and DBT
Outputs, for compatible instruments:
APA, APB, BWR, DBT, DPT, GGA, GLL, GSA, GSV,
RMB, RMC, MTW, VHW, VLW, VTG, XTE
Routes: 25 Routes, with up to 50 points each
Tracks: By time or distance, one track of 2000
points and four of 500 points.
Chart datums
121 Chart datums (see next page)
One user-defined map shift.
STANDARDS COMPLIANCE
EMC:
USA: FCC Part 15 Class B.
Chart scale: 0.05 to 4096 nm for chart (chart
Europe: (CE) EN64000-6-1 and EN64000-6-3
New Zealand and Australia: (C Tick) AS-NZS
3548.
dependent) down to 0.01 nm in plotter mode.
SONAR FISHFINDING
Depth range:
0.6 m (2 ft) to 1000 m (3300 ft )
Environment: IPx6/IPx7/CFR46 (with card holder
and connections in place)
Sonar output:
Power: Variable, up to 600 W RMS
Dual frequency: 50 khz and 200 kHz
84
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
33.1 mm ( 1.3 ")
164.0 mm ( 6.5 ")
32.0 mm ( 1.3 ")
88.5 mm ( 3.5 ")
List of datums
Adindan
Afgooye
Anna 1 Astro 1965
ARC 1960
Astro DOS 71/4
Australian Geodetic 1966
Bellevue (IGN)
Bogota Observatory
Campo Inchauspe 1969
Cape Canaveral
Chua Astro
Dabola
DOS 1968
European 1979
Geodetic Datum 1949
Gunung Segara
Hermannskogel
Hu-Tzu-Shan
AIN EL ABD 1970
Antigua Island Astro 1943
Ascension Island 1958
Astro Station 1952
Australian Geodetic 1984
Bermuda 1957
Bukit Rimpah
Canton Astro 1966
Carthage
Co-ord. Sys.1937 Estonia
Deception Island
Easter Island 1967
Fort Thomas 1955
Graciosa Base Sw 1948
GUX 1 Astro
American Samoa 1962
ARC 1950
Astro Beacon ‘E’1945
Astro Tern Island (Frig) 1961
Ayabelle Lighthouse
Bissau
Camp Area Astro
Cape
Chatham Island Astro 1971
Corrego Alegre
Djakarta (Batavia)
European 1950
Gan 1970
Guam 1963
Herat North
Hong Kong 1963
Indian 1954
Hjorsey 1955
Indian
Indian 1975
Indian 1960
Indonesian 1974
ISTS 073 Astro 1969
Kerguelen Island 1949
L. C. 5 Astro 1961
Luzon
Ireland 1965
Johnston Island 1961
Kertau 1948
Leigon
M’Poraloko
ISTS 061 Astro 1968
Kandawala
Kusaie Astro 1951
Liberia 1964
Mahe 1971
Massawa
Minna
Merchich
Midway Astro 1961
Nahrwan Masirah Is. Oman
Naparima, BWI
North Sahara 1959
Old Hawaiian
Pico de las Nieves
Pointe Noire 1948
Provis. South Chilean 1963
Qatar National
Montserrat Island Astro 1958
Nahrwan Saudi Arabia
North American 1983
Old Egyptian 1907
Ord. Survey Great Britain 1936
Point 58
Nahrwan United Arab Emirates
North American 1927
Observatorio Meteorolog. 1939
Oman
Pitcairn Astro 1967
Porto Santo 1936
Puerto Rico
Provis. South American 1956
Pulkovo 1942
Qornoq
Reunion
Rome 1940
S-42 (Pulkovo 1942)
Sapper Hill 1943
Sierra Leone 1960
South Asia
Tokyo
Voirol 1874
Santo (DOS) 1965
Schwarzeck
S-JTSK
Tananarive Observatory 1925
Tristan Astro 1968
Voirol 1960
Sao Braz
Selvagem Grande 1938
South American 1969
Timbalai 1948
Viti Levu 1916
Wake Island Astro 1952
Yacare
Wake-Eniwetok 1960
Zanderij
WGS 84
Northstar Explorer 657 Installation and Operation Manual
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B - Troubleshooting
This troubleshooting guide is written with
the assumption that the user has read and
understood the relevant sections in this manual.
Repairs to the product may only be carried out
by a service center approved by Northstar. If the
product must be sent into a service center for
repair, it is essential to send in the transducer(s) at
the same time.
It is possible in many cases to solve difficulties
without having to send the display unit back to
the manufacturer for repair. Please follow this
troubleshooting section before contacting the
nearest Northstar dealer.
More information can be found on our website:
There are no user serviceable parts. Specialized
methods and testing equipment are required
to ensure that the display unit is reassembled
correctly and is waterproof. Users who service the
product themselves will void the warranty.
B-1 General problems
1-1 The 657 won’t turn on:
1-2 The 657 won’t turn off:
a
The 657 is designed to operate on a 12/24
volt battery system, where the voltage may
vary from 10.5 to 30.5 volts. If an excessive
voltage is supplied, a fuse will be tripped,
turning the display unit off. Check the fuse.
The 657 may have been wired for Auto
power. In this case, the 657 cannot be turned
off while the ignition power is on (see section
2-2).
1-3 If the 657 beeps when turned on but
nothing is displayed:
b
c
Check that the power cable connector at the
back of the display unit is securely plugged
in and the collar is locked in place. The collar
must be secure for watertight connection.
The 657 may be operating, but the backlight
settings may have been set too low (see
section 2-3).
Measure the battery voltage while the battery
is under load - turn on some lights, radio or
other electrical equipment connected to the
battery. If the voltage is less than 10 volts:
1-4 The wrong language is displayed:
See section 17-1.
-
the battery terminals or wiring on the
terminals may be corroded.
-
the battery may not be charging
correctly or may need replacing.
d
Inspect the power cable from end to end for
damage such as cuts, breaks, squashed or
trapped sections.
e
f
Check power wiring (see section 18-4).
Check for corrosion on the power cable
connector and clean or replace if required.
g
Check fuses that are placed in line with the
power cable. A fuse can be blown despite
appearing to be good or the fuse may be
corroded. Test the fuse or replace it with a
fuse known to be good.
86
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
B-2 GPS navigation problems
2-1 No GPS fix or long time to get fix at
startup:
2-5 The time or date on satellite window is
wrong or off:
a
May occur occasionally if the antenna does
not have a clear view of the sky. The satellite
positions are constantly changing.
a
No GPS fix.
b
In simulate mode. Turn simulate mode off
(see section 17-15).
b
Antenna cable not connected to display unit.
c
Local time offset is wrong (see section 17-13).
The Local Time Offset must be changed
when daylight saving time starts or ends.
2-2 657 GPS position different from true
position by more than 10 m (33 ft):
a
b
c
657 in simulate mode. Turn simulate mode off
(see section 17-15).
2-6 Autopilot not responding to 657; no
NMEA output:
The normal error in GPS position will exceed
10 m (33 ft) for about 5% of the time.
a
NMEA output disabled or the required NMEA
sentences are not turned on. Check NMEA
settings (see section 17-10).
Under special circumstances the US
Department of Defence may introduce a
deliberate and changing error in the GPS
positions of up to 300 m (1000 ft).
b
Check that the instrument is connected
correctly.
2-7 No DGPS fix or loss of DGPS fix:
2-3 657 position different from same
position on local charts:
a
To receive a DGPS fix, WAAS/EGNOS must be
enabled or an optional DGPS antenna fitted
(see section 7).
a
b
c
657 in simulate mode. Turn simulate mode off
(see section 17-15).
b
c
With WAAS/EGNOS: Boat out of coverage
area (see section 7).
Incorrect chart datum. Select the correct
chart datum (see section 17-2).
With WAAS: GPS antenna does not have a
clear view of the horizon towards the equator.
Map shift has been applied wrongly. Clear
map shift, then reapply if necessary (see
section 17-2).
b
With beacon DGPS: boat out of range of a
DGPS beacon.
2-4 Can not see boat on chart:
Press
to switch to center on boat
mode (see section 3-2-1).
B-3 Fuel consumption problems
3-1 Fuel used or remaining seem inaccurate:
This is particularly noticable with underfloor
tanks.
a
657 is not wired for auto power (see section
18-4).
e
Fuel transducers wear out over time and
should be replaced after every 5000 litres of
fuel.
b
In rough seas, fuel may surge back and forth
through the fuel transducer, resulting in
incorrect readings. Try installing a one-way
valve between the fuel transducer and the
fuel tank.
3-2 Flow indicates no fuel or low fuel:
a
Check that the number of engines is set to 1
(see section 17-5).
c
The Set remainingfuel value must be
b
Check that the fuel cable connectors are
securely plugged in and the collar is locked
in place. The collar must be locked in place to
give a watertight connection.
reset after every refuelling (see section 12-1).
d
The fuel tank may not refill to the same
capacity each time due to air pockets.
Northstar Explorer 657 Installation and Operation Manual
87
Download from Www.Somanuals.com. All Manuals Search And Download.
c
A fuel transducer may be clogged. If so,
remove the transducer from the fuel line
and gently blow through it in the opposite
direction to the fuel flow.
3-4 Erratic Fuel Flow readings:
a
The fuel flow transducer may have been
mounted too close to the fuel pump or may
be subject to excessive vibration. Refer to the
installation instructions supplied with the fuel
transducer.
A fuel filter between the fuel transducer and
the fuel tank must be installed as per the fuel
installation guide. Failure to do so will void
the warranty.
b
c
Check for leaks in the fuel line or in the fuel
pickup in the tank.
d
e
Inspect the fuel cable from end to end for
damage such as cuts, breaks, trapped or
squashed sections.
The Flow filtervalue is not suitable for
the engine. Check that the value is not set
to zero, then try increasing the value until a
steady flow rate is shown (see section 17-5).
Check that the fuel filter is clean.
3-3 A twin engine installation shows only one
flow rate:
3-5 There is no reading for fuel economy:
a
The boat must be travelling through the
a
Check that the number of engines is set to 2
(see section 17-5).
water to generate an Economyreading.
Check that the paddlewheel on the
b
transducer is spinning freely and that the two
magnets in the paddlewheel are still in place.
B-4 Sonar fishfinding problems
4-1 The 657 operates erratically:
are securely plugged in and the collars are
locked in place. The collars must be secure for
watertight connection.
a
Check that the transducer does not have
debris (e.g. weed, plastic bag) caught
around it.
g
h
i
Inspect the power cable from end to end for
damage such as cuts, breaks, squashed or
trapped sections.
b
The transducer may have been damaged
during launching, running aground or
while underway with debris etc. If the
transducer has been impacted, it may have
been kicked up on the bracket. If it is not
physically damaged, reset the transducer
back to its original position. (See the Transom
Transducer Installation Guide.)
Ensure there is not another fishfinder or
depth sounder turned on, which may
interfere with this 657.
Electrical noise from the boat’s engine or
an accessory may be interfering with the
transducer(s) and/or the 657. This may cause
the 657 to automatically decrease the Gain
unless using Manual Gain.
c
When the transducer is less that 2 ft (0.6 m)
from the bottom, the depth readings may
become inconsistent and erratic.
The 657 thus eliminates weaker signals such
as fish or even the bottom from the display.
This may be checked by switching off other
instruments, accessories (e.g. bilge pump)
and the motor until the offending device
is located. To stop problems from electrical
noise, try:
d
e
Manual Gain may be set too low, which may
cause weak bottom echo or no fish signals. If in
Manual Gain, try increasing the Gain.
Ensure the back of the bottom surface of the
transducer is slightly lower than the front and
the front is as deep in the water as possible
in order to minimize the generation of
bubbles through cavitation. (See the Transom
Transducers Installation Guide)
-
re-routing the power and transducer
cable(s) away from the boat’s other
electrical wiring.
f
Check the transducer and power cable
connectors at the back of the display unit
-
routing the display unit’s power cable
directly to the battery with an in-line fuse.
88
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2 Bottom is not displayed:
4-5 There is a double bottom trace displayed:
a
The 657 may have Manual Range selected
and the depth may be outside the range
value selected. Either change the 657 to
Auto Range or select another depth range
(see section 8-5).
a
The boat may be in an area that generates
shadows (see section 8-2).
b
In shallow water, the echoes may bounce.
Reduce the gain setting (see section 8-6)
and/or reduce the sonar pulse power (see
section 17-3).
b
The depth may be outside the 657’s range.
While in Auto Range, the display unit will
display “--.-” to indicate that there is no bottom
detected. A display of the bottom should
reappear when in shallower water.
c
Decrease the Range.
4-3 The bottom is displayed too far up
the screen:
The 657 may have Manual Range selected
and the selected Range value is too high for
the depth. Either change the 657 to Auto
Range or select another depth range (see
section 8-5)
4-4 Bottom echo disappears or erratic digital
reading while the boat is moving:
a
Ensure the back of the bottom surface of
the transducer is slightly lower than the
front and the front is as deep in the water as
possible in order to minimise the generation
of bubbles through cavitation. (See the
Transom Transducers Installation Guide, for
more information.)
b
The transducer may be in turbulent water.
Air bubbles in the water disrupt the echoes
returned, interfering with the 657’s ability to
find the bottom or other targets. This often
happens when the boat is reversed. The
transducer must be mounted in a smooth
flow of water in order for the 657 to work at
all boat speeds.
c
Electrical noise from the boat’s motor can
interfere with the 657. Try some suppression
spark plugs.
Northstar Explorer 657 Installation and Operation Manual
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C - Glossary and navigation data
Glossary
Attention Area - An important area on a chart,
such as a restricted anchorage or a shallow area
(see section 17-2).
MMSI - Maritime Mobile Service Identity. Unique
identification number for a vessel, for use in
Digital Selective Calling.
AIS - Automatic Identification System. A System
where vessel information (location, course, speed,
etc.) is broadcast by VHF radio, for use by other
vessels in navigation and collision avoidance.
MOB - Man overboard.
MOB function - Starts navigating back to the
place where someone fell overboard (see section
2-4).
Bathymetric line - A depth contour line on
the chart.
NavBus - A way of connecting Northstar
instruments together to share data (see section
18-9).
Chart card - A plug-in card that stores chart data
for a region (see section 1-3).
NMEA - National Marine Electronics Association.
C-MAP™ chart card - See Chart card.
NMEA 0183 - A standard for interfacing marine
C-MAP™ user card - See User card.
electronic devices (see section 18-10).
CPA - Closest Point of Approach. The closest
distance two vessels will come to each other
based on their current course and speed.
Route: Two or more waypoints linked in
sequence to form a course for the boat (see
section 6).
Cursor - A
symbol on the display (see section
SmartCraft - A feature of Mercury Marine
3-2).
engines for monitoring engine performance.
DGPS - Differential Global Positioning System. A
navigation tool based on GPS with some errors
corrected (see section 7).
TCPA - Time to Closest Point of Approach.
Time until the closest point of approach for two
vessels.
DSC - Digital Selective Calling. A feature of
marine radios enabling communication between
specific vessels, as well as distress alerts.
User card - A plug-in card that stores waypoints,
routes and tracks (see section 1-2).
UTC - Universal Time Coordinated or Coordinated
Universal Time, which is a standard world time,
formerly called Greenwich Mean Time (GMT).
Goto - A simple way of navigating straight to a
waypoint or to the cursor position (see section
3-1).
VHF - Very High Frequency. The frequency range
GPS - Global Positioning System. A satellite-
used by marine radios.
based navigation tool (see section 7).
Waypoint - A position that you can set on the
657 chart, for example a fishing spot or a point on
a route (see section 5).
Leg - The straight segments of a route between
waypoints. A route with four waypoints has three
legs.
90
Northstar Explorer 657 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigation data
The boat is sailing from the start to the destination and has moved off the plotted course from the start
to the destination.
BRG
Bearing to Destination: Bearing to the destination from the boat.
BRG Bearing to cursor: Bearing to cursor from boat (cursor mode, see section 3-2-1 [note the -1 added
there])
CDI
Course Deviation Indicator: When the boat is navigating to a point, the chart and highway
windows show a parallel line on either side of the plotted course. These two lines are called the
Course Deviation Indicator (CDI) lines. The distance from the plotted course to a CDI line is the
CDI scale.
Set the CDI scale (see section 17-2) to the maximum distance that the boat should deviate from
the plotted course.The chart and highway windows show the CDI lines, which are like a highway
over the water where the boat will move.The windows show how far the boat has deviated from
the plotted course and if the boat is approaching a CDI line. If the XTE alarm is enabled (see
section 17-9) an alarm will sound if the boat reaches a CDI line.
COG
CTS
DTG
ETA
Course Over Ground: Direction in which the boat is moving over the ground.
Course To Steer: Optimum course to steer to return to the plotted course.
Distance To Go: Distance from the boat to the destination.
Expected Time of Arrival: At the destination, assuming that SOG and COG remain constant.
DST Distance from boat to cursor (cursor mode, see section 3-2)
SOG
Speed Over Ground: Current boat speed over the ground. This is not necessarily the same as
the boat speed through the water nor the speed at which it is approaching the destination.
STR
TTG
XTE
Steering: The difference between COG and CTS.
Time To Go: The estimated time to reach the destination.
Cross Track Error: The distance from the boat to the nearest point of the plotted course. XTE
may have a letter: R means steer to the right to return to the plotted course, L means steer to
the left.
VMG
Velocity Made Good: The speed at which the boat is approaching the destination.
Destination
Destination
Plotted
course
DTG (distance)
VMG (speed)
XTE
(distance)
SOG (speed)
STR
Boat
position
BRG
COG
CTS
CDI scale
(distance)
CDI scale
(distance)
Plotted
course
Boat position
Start
Start
Northstar Explorer 657 Installation and Operation Manual
91
Download from Www.Somanuals.com. All Manuals Search And Download.
".&3*$"4
ꢀꢁꢂ4VECVSZꢂ3PBEꢃ
&6301&
6OJUꢂꢆꢃꢂ0DFBOꢂ2VBZꢃ
#FMWJEFSFꢂ3Eꢃꢂ4PVUIBNQUPOꢃ
40ꢄꢍꢂꢎ2:ꢃꢂ&/(-"/%
1Iꢇꢂꢈꢍꢍꢂꢆꢀꢊꢁꢂꢀꢀꢉꢉꢆꢆ
'BYꢇꢂꢈꢍꢍꢂꢆꢀꢊꢁꢂꢀꢀꢁꢀꢍꢎ
OPSUITUBSVL!OPSUITUBSOBWꢋDPN
"DUPOꢃꢂ."ꢂꢁꢄꢅꢆꢁꢃꢂ64"
1Iꢇꢂꢈꢄꢂꢉꢅꢊꢋꢊꢉꢅꢋꢌꢌꢁꢁꢂ
1Iꢇꢂꢈꢄꢂꢊꢁꢁꢋꢌꢆꢊꢋꢍꢍꢊꢅ
'BYꢇꢂꢈꢄꢂꢉꢅꢊꢋꢊꢉꢅꢋꢅꢆꢍꢄ
TBMFT!COUNBSJOFꢋDPN
"6453"-*"
10ꢂ#PYꢂꢍꢅꢉꢃ
/&8ꢂ;&"-"/%
10ꢂ#PYꢂꢌꢊꢂꢄꢎꢎꢃꢂ
(MBEFTWJMMFꢃꢂ/48ꢂꢆꢄꢄꢄꢃ
"6453"-*"
/FXUPOꢃꢂ"VDLMBOE
"VDLMBOEꢃꢂ/&8ꢂ;&"-"/%
1Iꢇꢂꢈꢌꢍꢂꢉꢂꢍꢊꢄꢂꢁꢎꢁꢁ
'BYꢇꢂꢈꢌꢍꢂꢉꢂꢍꢊꢄꢂꢁꢎꢉꢁ
OPSUITUBSO[!OPSUITUBSOBWꢋDPN
1Iꢇꢂꢈꢌꢄꢂꢆꢂꢉꢊꢅꢉꢂꢉꢁꢌꢁ
'BYꢇꢂꢈꢌꢄꢂꢆꢂꢉꢊꢅꢉꢂꢉꢁꢁꢉ
OPSUITUBSBVT!OPSUITUBSOBWꢋDPN
Made in New Zealand
MN000651A-G
Download from Www.Somanuals.com. All Manuals Search And Download.
|