Part No. 210667-A
December, 2000
4401 Great America Parkway
Santa Clara, CA 95054
Installing the e-mobility
802.11b Wireless LAN
DSSS Access Point
210667-A
Download from Www.Somanuals.com. All Manuals Search And Download.
The conformity assessment procedure referred to in Article 10(5) and detailed in
Annex IV of Directive 1999/5/EC has been followed with the involvement of the
following Notified Body(ies):
BABT, Claremont House, 34 Molesey Road, Walton-on-Thames, KT12 4RQ
Identification Mark:
0168 The equipment also carries the Class 2 equipment identifier
The technical documentation relevant to the above equipment can be made available
for inspection on application to:
Symbol Technologies EMEA, Symbol Place, Winnersh Triangle, Berkshire,
RG 41 5TP, UK
Dornu Narnor Senior Director, Regulatory
(name) (title)
7 September 2000
(signature of authorised person) (date)
Symbol Spectrum24 HR products have been rebranded to Nortel Networks
e-mobility 802.11b Wireless LAN DSSS products and the above Declaration of
Conformity applies to both brands.
Federal Communications Commission (FCC) Compliance Notice: Radio
Frequency Notice
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy. If it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case users will be required to take whatever
measures may be necessary to correct the interference at their own expense.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EN 55 022 Statement
This is to certify that the Nortel Networks e-mobility 802.11b Wireless LAN DSSS
Access Point is shielded against the generation of radio interference in accordance
with the application of Council Directive 89/336/EEC, Article 4a. Conformity is
declared by the application of EN 55 022 Class A (CISPR 22).
Warning: This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case, the user may be required to take appropriate
measures.
Achtung: Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen
können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in welchen Fällen
der Benutzer für entsprechende Gegenmaßnahmen verantwortlich ist.
Attention: Ceci est un produit de Classe A. Dans un environnement domestique, ce
produit risque de créer des interférences radioélectriques, il appartiendra alors à
l’utilisateur de prendre les mesures spécifiques appropriées.
EC Declaration of Conformity
This product conforms to the provisions of the R&TTE Directive 1999/5/EC.
Bureau of Standards, Metrology and Inspection (BSMI) Statement
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (e-mobility 802.11b Wireless LAN DSSS Access Point) does
not exceed the Class A limits for radio-noise emissions from digital apparatus as set
out in the Radio Interference Regulations of the Canadian Department of
Communications.
Warning: To comply with FCC and Industry Canada exposure requirements,
antennas that are mounted externally at remote locations or operating near users at
standalone desktop or similar configurations must operate with a minimum
separation of 20 cm from all persons.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Règlement sur le brouillage radioélectrique du ministère des
Communications
Cet appareil numérique (e-mobility 802.11b Wireless LAN DSSS Access Point)
respecte les limites de bruits radioélectriques visant les appareils numériques de
classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère
des Communications du Canada.
European Economic Area
The European variant is intended for use throughout the European Economic Area;
however, authorization for use is restricted as follows:
European standards dictate maximum radiated transmit power of 100mW EIRP and
frequency range 2.400 - 2.4835 GHz.
In France, the equipment is restricted to the 2.4465 - 2.4835 GHz frequency range.
In Belguim outside, the equipment is restricted to the 2.460 - 2.4835 frequency
range.
The operation of this equipment in Italy requires a user license.
Hard-Copy Technical Manuals
You can print selected technical manuals and release notes free, directly from the
Internet. Go to the www25.nortelnetworks.com/library/tpubs/ URL. Find the
product for which you need documentation. Then locate the specific category and
model or version for your hardware or software product. Use Adobe Acrobat
Reader to open the manuals and release notes, search for the sections you need, and
URL to download a free copy of the Adobe Acrobat Reader.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
How To Get Help
If you purchased a service contract for your Nortel Networks product from a
distributor or authorized reseller, contact the technical support staff for that
distributor or reseller for assistance.
If you purchased a Nortel Networks service program, contact one of the following
Nortel Networks Technical Solutions Centers:
Technical Solutions Center
EMEA
Telephone
(33) (4) 92-966-968
(800) 2LANWAN or (800) 252-6926
(61) (2) 9927-8800
(800) 810-5000
North America
Asia Pacific
China
An Express Routing Code (ERC) is available for many Nortel Networks products
and services. When you use an ERC, your call is routed to a technical support
person who specializes in supporting that product or service. To locate an ERC for
your product or service, go to the www12.nortelnetworks.com/ URL and click ERC
at the bottom of the page.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The e-mobility 802.11b Wireless LAN DSSS Access Point (AP)
provides a bridge between Ethernet wired LANs and e-mobility
wireless networks. It provides transparent access between
Ethernet wired networks and radio-equipped mobile units (MUs).
MUs include all of Nortel Networks™ e-mobility™ terminals,
scanners, third-party devices, and other equipment.
The access point provides an 11 Mbps data transfer rate on the
radio network. For further information about access point
configuration, refer to Reference for the e-mobility 802.11b
Wireless LAN DSSS Access Point (part number 210669-x).
Precautions
Before installing the access point (AP) verify the following:
•
•
The location for the unit is dry and dust free. Install in wet or
dusty areas only with additional protection. Contact a Nortel
Networks representative for more information.
The environment has a temperature range between -20° C
and 55° C.
Requirements
The minimum installation requirements for a single-cell, peer-to-
peer network are a power outlet and an antenna.
Note: Use and test the radio network with a properly
equipped e-mobility mobile unit.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Connection
Locate connectors for Ethernet, antennas, and power on the back
of the AP. Ethernet configurations vary according to the
environment.
Note: The e-mobility site survey utility can be used to
determine the number of access points to install and their
locations.
10BASE-T UTP
Use a 10BASE-T connection for multiple access points or an
access point attached to a wired UTP Ethernet hub or switch.
Normal 10BASE-T limitations apply.
To establish a 10BASE-T connection:
1
2
3
Plug the data cable RJ-45 connector into the access point
RJ-45 connector.
Plug the other end of the data cable into the LAN access port,
possibly a hub or wall connection.
Add additional access points as needed.
Note: When connecting the e-mobility access point to an
Ethernet switch, ensure the switch port parameters are set
to 10 Mbps Half Duplex. Severe performance
degradation may result from mis-matched speed or
duplex modes.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the AP
The AP rests on a flat surface or attaches to any hard, flat, stable
surface. Position the AP at any angle. Use the standard-mounting
kit provided.
Choose an option based on environment:
•
•
Resting flat
The AP rests on the four rubber pads on its underside. Place
the AP on a surface clear of debris and away from traffic.
Attaching on the wall in any direction
The AP attaches to a wall and can be oriented in any position
as long as the antennas are oriented vertically.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
e-mobility 802.11b Wireless LAN DSSS Access Point
Antennas
Antenna coverage is analogous to lighting. Users might find an
area lit from far away to be not bright enough. An area lit sharply
might minimize coverage and create dark areas. Uniform antenna
placement in an area (like an even placement of light bulbs)
provides even, efficient coverage.
Place the antenna using the following guidelines:
•
•
•
Install the antenna as high as practical.
Orient the antenna vertically for best reception.
Point the antenna downward if attaching the AP to the
ceiling.
The AP requires one antenna and can use two. Two antennas
provide diversity that can improve signal reception.
Attach antennas to ANTENNA connectors on the back of the AP.
For a single antenna, use the PRIMARY ANTENNA connector
and set the Antenna Diversity setting to Primary Only. This is the
left antenna connector when viewed from the front of the unit. It
is identified by one vertical bar on the bottom of the unit. The
secondary antenna is marked with two vertical bars.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
The standard antenna performs well in most office environments.
Obtain additional or higher-performance antennas from Nortel
Networks. Contact a Nortel Networks representative to order the
following models:
•
•
•
•
Standard rubber antenna
Single high-performance antenna
Twin high-performance diversity antennas
Mountable F-plane antenna
If installing two antennas, enable the Antenna Diversity option in
the User Interface. Refer to Access Point Installation in the
Reference for the e-mobility 802.11b Wireless LAN DSSS Access
Point (part number 210669-x).
Antenna Extension Cables
Nortel Networks offers extension cables for access point
antennas. Some range loss occurs when increasing the distance
between the antenna and the access point.
Length
6 ft
Loss
2.0 dB
4.0 dB
Range Loss
5%
12 ft
10%
To order extension cables, contact a Nortel Networks
representative.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Power Adapter
The power adapter connects to the rear of the access point and to
a power outlet.
To connect the power adapter:
1
2
3
Verify that the power adapter matches the country-of-use
requirements.
Plug power adapter cable into the socket on the back of the
access point.
Plug the adapter into an outlet.
When the Power indicator on the front of the access point stops
flashing and lights solid green and the Wireless LAN Activity
indicator begins flickering, the access point is functional and
ready to associate with MUs.
Note: The e-mobility access point may also be powered
by using the Remote Power Interface (RPI) in
conjunction with the AC Power Adapter. The RPI
enables the access point to be installed in locations
without direct access to AC power. Refer to 210672A,
“Installing the e-mobility 802.11b Wireless LAN DSSS
Remote Power Inteface” for details.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Indicators
The LED indicators provide a status display indicating
transmission and error conditions. The indicators are:
Power
Link
Flashing indicates AP initialization.
Shows steady green during operation.
Flashing indicates data transfers on
wired connection.
Activity
Flickering indicates beacons and data
transfers with MUs.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Physical Characteristics:
Dimensions
1.25 inches H x 5.5 inches L x 7.75 inches W
(3.18 cm H x 14.97 cm L x 19.69 cm W)
Weight (w/power supply)
Operating Temperature
Storage Temperature
Humidity
1 lbs. (0.454 kg)
-4 ºF to 131 ºF (-20 ºC to 55 ºC)
-40 ºF to 149 ºF (-40 ºC to 65 ºC)
10% to 95% noncondensing
40 G, 11 ms, half-sine
Shock
ESD
meets CE-Mark
Drop
withstands up to a 30 in. (76 cm) drop to
concrete with possible surface marring
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio Characteristics:
The frequency range used by the e-mobility 802.11b WLAN
DSSS components is within 2.4 GHz to 2.5 GHz unlicensed ISM
band. From one to eleven of the fourteen 22 GHz wide channels,
country dependent.
Frequency
Allowed Channel Range
1 - 11
Country
United States
Israel
2.412 - 2.470
2.430 - 2.447
2.457 - 2.463
2.458 - 2.472
2.400 - 2.485
5 - 8
10 - 11
Spain
10 - 13
France
Japan
1 - 14
TX Max. Radiated
EIRP
US: FCC part 15.247
Europe: ETS 300 320
Japan: RCR STD-33
Binary GFSK
Modulation
TX Out-of-Band
Emissions
US: FCC part 15.247, 15.205,
15.209
Europe: ETS 300 320
Japan: RCR STD-33
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio Data Range
11 Mbps range
Open environment - approximately 400 feet
(121.92 meters)
Typical office or retail environment - approximately
150 feet (45.72 meters)
Dependent upon antenna selection, building
construction, and environmental characteristics.
5.5 Mbps range
2 Mbps range
1 Mbps range
Open environment - approximately 700 feet
(213.36 meters)
Typical office or retail environment - approximately
250 feet (76.20 meters)
Dependent upon antenna selection, building
construction, and environmental characteristics.
Open environment - approximately 800 feet
(243.84 meters)
Typical office or retail environment - approximately
300 feet (91.44 meters)
Dependent upon antenna selection, building
construction, and environmental characteristics.
Open environment - approximately 1200 feet
(365.76 meters)
Typical office or retail environment - approximately
450 feet (137.16 meters)
Dependent upon antenna selection, building
construction, and environmental characteristics
Radio Output Power
100 mW
16
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
|