Nokia Bluetooth Headset BH-303
7
8
9
6
6
6
12
6
11
6
10
6
13
6
Issue1
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Introduction
The Nokia Bluetooth Headset BH-
may be subject to interference from
303 allows you to make and receive obstructions, such as walls, or other
calls while on the move. You can
use the headset with compatible
devices that support Bluetooth
wireless technology.
electronic devices.
The headset complies with the
Bluetooth Specification 2.0 + EDR
that supports the Headset Profile
1.1 and Hands-Free Profile 1.5.
Read this user guide carefully
before using the headset. Also read Check with the manufacturers of
the user guide for your mobile
device, which provides important
safety and maintenance
information. Keep the headset and
its accessories out of reach of small
children.
other devices to determine their
compatibility with this device.
There may be restrictions on using
Bluetooth technology in some
locations. Check with your local
authorities or service provider.
Bluetooth wireless
technology
Bluetooth wireless technology
allows you to connect compatible
devices without cables. The mobile
device and the headset do not need
to be in line of sight, but they
should be within 10 meters (30
feet) of each other. Connections
ownload from Www.Somanuals.com. All Manuals Search And Downloa
3
Get started
Warning: Use only
chargers approved by
Nokia for use with this
The headset contains the following
parts shown on the title page:
power key (1), charger connector
(2), earpiece (3), microphone (4),
earloop (5), volume key (6),
indicator light (7), and answer/end
key (8).
particular enhancement. The use of
any other types may invalidate any
approval or warranty and may be
dangerous.
When you disconnect the power cord
of any enhancement, grasp and pull
the plug, not the cord.
Before using the headset, you must
charge the battery and pair the
headset with a compatible device.
Charge the battery
Parts of the headset are magnetic.
Metallic materials may be attracted to
the headset. Do not place credit cards
or other magnetic storage media near
the headset, because information
stored on them may be erased.
The headset has an internal,
nonremovable, rechargeable
battery. Do not attempt to remove
the battery from the device, as you
may damage the device.
Chargers
1. Connect the charger to a wall
outlet.
Check the model number of any
charger before using it with this
headset. The headset is intended for
use with the
2. Connect the charger cable to
the charger connector. The red
indicator light is on while
charging. It may take a while
before charging starts. If
AC-3, AC-4, and DC-4 chargers.
ownload from Www.Somanuals.com. All Manuals Search And Downloa
4
charging does not start,
and the green indicator light is
displayed.
disconnect the charger, plug it
in again, and retry. Charging the
battery fully may take up to 1
hour and 30 minutes.
To switch off, press and hold the
power key until the headset beeps
and the red indicator light is
displayed briefly.
3. When the battery is fully
charged, the indicator light
turns to green. Disconnect the
charger from the headset and
the wall outlet.
Pair the headset
1. Ensure that your mobile device
is switched on and the headset
is switched off.
The fully charged battery has power
for up to 6 hours and 30 minutes of
talk time or up to 150 hours of
standby time. However, the talk and
standby times may vary when used
with different compatible
2. Press and hold the power key
until the green indicator light
starts to flash quickly.
3. Activate the Bluetooth feature
on the mobile device, and set
the device to search for
Bluetooth devices, usage settings,
usage styles, and environments.
Bluetooth devices.
When battery power falls low, the
headset beeps, and the red
indicator light starts to flash.
4. Select the headset from the list
of found devices.
5. Enter the passcode 0000 to pair
and connect the headset to your
device. In some devices you may
need to make the connection
separately after pairing. You
Switch the headset on or off
To switch on, press and hold the
power key until the headset beeps
ownload from Www.Somanuals.com. All Manuals Search And Downloa
5
only need to pair the headset
with your device once.
device menu where you can view
the currently paired Bluetooth
devices. The headset is now ready
for use.
If the pairing is successful, the
headset beeps and appears in the
Basic use
Place the headset on the ear Change the cover
To use the headset with the
The headset may be supplied with
earloop, insert the headset into the front covers in different colors. To
catch (9) and gently push it
change the cover, pull the current
downwards until it locks into place. cover starting from the top (13),
Slide the earloop behind your ear
starting from the top (10), rotate
the earloop for the best fit, and
push the earloop toward your
mouth (11). If you wear an earring,
ensure that it is not accidentally
attached to the earloop. The
and push the new cover into place.
Call handling
To make a call, use your mobile
device in the normal way when the
headset is connected to the device.
If your device supports last number
redialing with the headset, press
the answer/end key twice while no
call is in progress.
earloop has a strap that allows you
to wear the headset on your neck.
To use the headset without the
earloop, detach it (12), and plug the
earpiece into your ear.
If your device supports voice dialing
with the headset, press and hold
the answer/end key when no call in
ownload from Www.Somanuals.com. All Manuals Search And Downloa
6
progress, and proceed as described
in the user guide of your device.
Clear settings or reset
To clear all the pairing settings
from the headset, switch off the
headset, and press and hold the
power key and the answer/end key
until the red and green indicator
lights start to alternate.
To answer or end a call, press the
answer/end key. To reject an
incoming call, press the answer/end
key twice.
To adjust the headset volume, press
the volume key up or down.
To reset the headset if it stops
functioning, although it is charged,
plug the headset into a charger, and
press the power key and the
To mute or unmute the
microphone, press the middle of the
volume key.
answer/end key at the same time.
To switch the call between the
headset and a compatible device,
press and hold the answer/end key.
Battery information
Your device is powered by a
Do not leave a fully charged battery
rechargeable battery. The battery can connected to a charger, since
be charged and discharged hundreds
of times, but it will eventually wear
out. Recharge your battery only with
Nokia approved chargers designated
for this device.
overcharging may shorten its lifetime.
If left unused, a fully charged battery
will lose its charge over time.
Never use any charger that is
damaged.
Unplug the charger from the electrical
plug and the device when not in use.
ownload from Www.Somanuals.com. All Manuals Search And Downloa
7
Leaving the device in hot or cold
places, such as in a closed car in
summer or winter conditions, will
even when the battery is fully charged.
Battery performance is particularly
limited in temperatures well below
reduce the capacity and lifetime of the freezing.
battery. Always try to keep the battery
Do not dispose of batteries in a fire as
they may explode. Batteries may also
explode if damaged.
between 15°C and 25°C (59°F and
77°F). A device with a hot or cold
battery may not work temporarily,
Care and maintenance
Your device is a product of superior
design and craftsmanship and should
be treated with care. The following
suggestions will help you protect your
warranty coverage.
•
•
Do not store the device in hot
areas. High temperatures can
shorten the life of electronic
devices, damage batteries, and
warp or melt certain plastics.
•
Keep the device dry. Precipitation,
humidity, and all types of liquids or
moisture can contain minerals that
will corrode electronic circuits. If
your device does get wet, allow it
to dry completely.
Do not store the device in cold
areas. When the device returns to
its normal temperature, moisture
can form inside the device and
damage electronic circuit boards.
•
•
Do not attempt to open the device.
•
Do not use or store the device in
dusty, dirty areas. Its moving parts
and electronic components can be
damaged.
Do not drop, knock, or shake the
device. Rough handling can break
internal circuit boards and fine
mechanics.
ownload from Www.Somanuals.com. All Manuals Search And Downloa
8
•
•
Do not use harsh chemicals,
cleaning solvents, or strong
detergents to clean the device.
Do not paint the device. Paint can
clog the moving parts and prevent
proper operation.
All of the above suggestions apply
equally to your device, battery,
charger, or any enhancement. If any
device is not working properly, take it
to the nearest authorized service
facility for service.
ownload from Www.Somanuals.com. All Manuals Search And Downloa
9
|