®
DLP HIGH-DEFINITION TELEVISION
MODELS
C9 Series
737 Series
837 Series
OWNER’S GUIDE
•
•
Guidelines for setting up and using your new widescreen TV start on page 7.
For questions:
-
-
-
E-mail us at [email protected].
Call Consumer Relations at 800-332-2119.
•
•
For information on System Reset, please see the back cover.
To order replacement or additional remote controls or lamp cartridges, visit our website at
•
837 Series. IR emitter cables for NetCommand home-theater control are available for
purchase from Mitsubishi. Call 800-553-7278 and request either part number 242D483020
(two-ended cable) or part number 299P254020 (four-ended cable).
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
4 TV Menus
Important Information About Your TV
Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . 32
Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Initial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Installation and Operating Notes . . . . . . . . . . . . . 4
Important Safety Instructions. . . . . . . . . . . . . . . . 5
Special Features of Your TV. . . . . . . . . . . . . . . . . 6
1 Basic Setup and Operation
Package Contents . . . . . . . . . . . . . . . . . . . . . . . 7
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . 7
First-Time Power-On. . . . . . . . . . . . . . . . . . . . . . 7
TV Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setting Up TV Inputs. . . . . . . . . . . . . . . . . . . . . 10
Basic TV Operation. . . . . . . . . . . . . . . . . . . . . . 12
5 NetCommand IR Control
About NetCommand IR Control . . . . . . . . . . . . . 45
IR Emitter Placement . . . . . . . . . . . . . . . . . . . . 46
Initial NetCommand Setup . . . . . . . . . . . . . . . . 47
Operating NetCommand-Controlled Devices . . . 48
2 TV Connections
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . 14
Inputs and Outputs. . . . . . . . . . . . . . . . . . . . . . 15
Y Pb Pr Component Video Device . . . . . . . . . . . 17
6 NetCommand IR Control of an A/V Receiver
Controlling an A/V Receiver after
NetCommand Setup. . . . . . . . . . . . . . . . . . . . 51
Setting Up A/V Receiver Control
H
DMI Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
DVI Video Device . . . . . . . . . . . . . . . . . . . . . . . 18
Composite Video Device. . . . . . . . . . . . . . . . . . 18
Antenna or Cable TV Service. . . . . . . . . . . . . . . 18
VCR or DVD Recorder to an Antenna or
Power and Volume . . . . . . . . . . . . . . . . . . . 52
Automatic Audio or Audio/Video Switching . . 53
Appendices
Wall Outlet Cable . . . . . . . . . . . . . . . . . . . . . . 19
VCR or DVD Recorder to a Cable Box . . . . . . . . 19
A/V Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . 20
A/V Receiver with HDMI Output. . . . . . . . . . . . . 20
Appendix A: Bypassing the Parental Lock . . . . . 57
Appendix B: Programming the Remote Control . 59
Appendix C: HDMI Control of CEC Devices . . . . 66
Appendix D: TV Care
Lamp-Cartridge Replacement and Cleaning . 69
Cleaning Recommendations . . . . . . . . . . . . 71
Care of the Remote Control . . . . . . . . . . . . . 71
Appendix E: Troubleshooting . . . . . . . . . . . . . . 72
3 Using TV Features
Selecting an Input . . . . . . . . . . . . . . . . . . . . . . 21
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ChannelView Channel Listings. . . . . . . . . . . . . . 22
Redirecting Audio Output . . . . . . . . . . . . . . . . . 22
Controlling A/V Receiver Sound Volume . . . . . . . 22
Status Display . . . . . . . . . . . . . . . . . . . . . . . . . 23
TV Signals and Display Formats. . . . . . . . . . . . . 24
3D Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Using the TV with a Personal Computer . . . . . . . 26
Camera Images and Music Files . . . . . . . . . . . . 28
Introduction to Home-Theater Control . . . . . . . . 31
Trademark and License Information . . . . . . . . . . 79
Mitsubishi TV Software. . . . . . . . . . . . . . . . . . . . 80
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Important Information About Your TV
Internal Fans
For Your Records
Internal cooling fans maintain proper operating tem-
peratures inside the TV. It is normal to hear the fans
when you first turn on the TV, during quiet scenes
while viewing the TV, and for a short time after shutting
off the TV. You may notice louder fan noise about 30
seconds after shutting off the TV and while using the
Bright Lamp Mode.
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the TV.
MODEL NUMBER
SERIAL NUMBER
PURCHASE DATE
RETAILER NAME
LOCATION
Lamp Replacement
For lamp-replacement instructions, see Appendix D.
To Order a Replacement Lamp Under Warranty
Call (800) 553-7278. Please have model number, serial
number, and TV purchase date available.
Important: All lamps replaced under warranty
must be returned to Mitsubishi where they will be
inspected for defect verification.
Installation and Operating Notes
Custom cabinet installation must allow for proper
air circulation around the television.
To Purchase a Replacement Lamp After Warranty
553-7278. Order new lamp part number 915B403001
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER
IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PRO-
VIDES GUIDELINES FOR THE PROPER GROUNDING AND,
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND
SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY
AS PRACTICAL.
TV Software
Do not attempt to update the software of this TV with
software or USB drives not provided by or authorized
by Mitsubishi Digital Electronics America, Inc. Non-
authorized software may damage the TV and will not be
covered by the warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Important Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
E XAMP LE OF ANTE NNA G R OUNDING
ANTE NNA
LE AD IN WIR E
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
G R OUND C LAMP
ANTE NNA
DIS C HAR G E UNIT
(NE C AR TIC LE 810-20)
E LE C TR IC
S E R VIC E
E QUIP ME NT
4) Follow all instructions.
G R OUNDING
C ONDUC TOR S
(NE C AR TIC LE 810-21)
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
G R OUND C LAMP S
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
P OWE R S E R VIC E G R OUNDING
E LE C TR ODE S YS TE M
NE C — NATIONAL E LE C TR IC AL C ODE
(NE C AR T 250, P AR T H)
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Outdoor Antenna Grounding
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.
Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts speci-
fied by the manufacturer or have the same character-
istics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
13) Unplug this apparatus
during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Special Features of Your TV
Your new high-definition widescreen television has
many special features that make it the perfect center of
your home entertainment system, including:
These inputs support HDMI 1.3 Deep Color (up to
36 bits) and the x.v.Color extended color gamut.
Used with an adapter, these HDMI inputs also
accept compatible digital DVI video signals. HDMI
inputs provide additional high-performance,
high-definition connections for maximum flexibility
in your choice of home theater products. The HDMI
inputs are HDCP copy-protection compatible.
1080p High-Definition DLP Display System
Your Mitsubishi HDTV uses Texas Instruments Digital
Light Processing™ technology for rear-projection TVs
to create the picture you see on screen. All images are
displayed at 1080p. The TV uses Plush 1080p® 5G to
convert lower-resolution signals to 1080p for display.
The TV can also accept 1080p original signals and
maintain them at 1080p through all processing until
displayed.
Easy Connect Auto Input Sensing
Easy Connect™ Auto Input Sensing automatically rec-
ognizes when you plug in a device and prompts you to
assign a name to it. The TV ignores any unused inputs,
so the result is an uncluttered menu where you can
easily find and select connected devices by name.
3D Ready
All Mitsubishi 1080p DLP HDTV’s are 3D Ready. This
feature lets you experience the new 3D technolo-
gies applied to many recent movies and video games.
Immerse yourself in your favorite video game, movie, or
sporting event displayed in 3D.
Home-Theater Control
HDMI Control
Available for all models. HDMI devices with Con-
sumer Electronics Control (CEC) capabilities may be
compatible with the TV’s HDMI Control feature. Com-
patible devices can receive control signals through the
HDMI connection, allowing the TV’s remote control to
operate some functions of these devices.
16:9 Widescreen Picture Format
Enjoy a full theatrical experience in the comfort of your
home. View pictures as film directors intended them.
Digital TV broadcasts, DVDs and newer video game
consoles support this widescreen format.
NetCommand with IR Learning
837 Series. Your Mitsubishi HDTV offers a new level
of networking that seamlessly integrates selected
older A/V products with new and future digital prod-
Integrated HDTV Tuner
Your widescreen Mitsubishi HDTV has an internal HDTV
tuner able to receive both over-the-air HDTV broad-
casts (received via an antenna) and non-scrambled
digital cable broadcasts, including non-scrambled
HDTV cable programming.
®
ucts. NetCommand supports IR (infrared) control of
products such as VCRs, DVD players, cable boxes, and
satellite receivers. NetCommand can “learn” remote
control signals directly from many devices, allowing you
to create a customized NetCommand-controlled home-
theater system. The necessary IR emitter cables are
available for purchase separately from Mitsubishi.
High-Definition Video Inputs
•
Component Video Inputs. Also called Y/Pb/Pr
inputs, these inputs receive standard analog video
formats of 480i, 480p, 720p, and 1080i high-defini-
tion signals. This provides a high level of flexibility
when connecting DVD players/recorders, cable
boxes, and satellite receivers.
ENERGY STAR® Compliance
This TV meets ENERGY STAR® efficiency standards in
all operating modes.
•
HDMI Inputs. These inputs accept digital 480i,
480p, 720p, 1080i, and 1080p video signals plus
PCM digital stereo signals. The HDMI™ inputs can
also accept a variety of PC signals and resolutions.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Basic Setup and Operation
1
Package Contents
Please take a moment to review the following list of
items to ensure that you have received everything.
Before You Begin
1. Review the important safety, installation, and oper-
ating information at the beginning of this book.
2. Choose a location for your TV.
1. Remote Control
•
Allow at least four inches of space on all sides
of the TV to help prevent overheating. Over-
heating may cause premature failure of the TV
as well as shortened lamp life.
2. Two AA Batteries
3. Basic Owner’s Guide
4. HDTV Quick-Setup Guide
5. Product Registration Card
•
•
Avoid locations where light may reflect off the
screen.
ACTIVITY
See the stand requirements on page 2.
GUIDE
MENU
INFO
BACK
3
3. Install the batteries in the remote control.
5
4. Plug the TV into an AC power outlet.
1
4
First-Time Power-On
AA
AA
2
1. Confirm that the remote
control is in TV mode.
•
Press the side button
once to light the mode
indicator and confirm
that TV mode is active.
To change, press the
side button additional
times to activate TV
mode.
Remote Control Batteries
1. Remove the remote control back cover.
•
TV
GUIDE
MENU
INFO
BACK
2. Aim the remote control
at the TV and press the
GUIDE
MENU
INFO
BACK
POWER key
Welcome screen.
Wait for the
.
2. Load the batteries, making sure the polarities
(+) and (-) are correct. Insert the negative (-)
end first.
3. Press if you wish to
change the menu language
to Español.
4. Press to highlight EXIT.
Press ENTER to clear the
menu.
3. Slide the cover back into place.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
1. Basic Setup and Operation
TV Controls
Remote Control
Press to select a TV activity
and input. See page 21.
ACTIVITY
VCR CABL/SAT TV DVD AUDIO
Control-mode indicator for device
type to control. Use the side button to
change.
GUIDE
MENU
ChannelView listings, page 22
.
TV main menu, page 32
Powers TV on or off.
ACTIVITY
GUIDE
INFO
BACK
TV status (page 23) or TV help.
Side button sets the control mode
for the type of device to operate. Set
mode to TV for normal TV viewing.
MENU
INFO
BACK
Steps back one menu; clears
the top menu or Status Display.
CHANNEL UP
VOLUME UP
MUTE
LAST Goes to the previously tuned channel.
.
CHANNEL DOWN
PAGE UP
VOLUME DOWN
Record/Playback controls for external devices
When remote control is programmed, page 59
HDMI control, page 68
Selects a channel number or
menu item.
ENTER
837 Series: NetCommand, page 48
Navigation controls
PAGE DOWN
(
PAUSE
)
Freezes a broadcast TV picture.
Displays a menu showing addi-
tional functions for the number
keys.
MORE
Number/letter keys
•
•
For the MORE menu in TV mode,
see below.
Channel tuning, page 12
With remote control programmed
for other device types, page 59.
The MORE menu in other modes is
specific to the device type.
For CEC-enabled devices, page 66
—
Adds a separator when enter-
ing digital channel numbers.
Clears some menu entries.
CANCEL
•
The MORE menu in TV mode
Note: To operate other audio/video
devices using the TV’s remote
control:
CC Closed captions, page 37
VIDEO Video adjustments, page 35
AUDIO Audio adjustments, page 36
•
•
•
See Appendix B, “Programming the Remote
Control.”
For HDMI devices compatible with the TV’s
HDMI Control feature, see Appendix C.
837 Series
-
See page 45 for NetCommand IR “Learn-
ing” of device keys.
For use of specific keys with NetCom-
mand-controlled devices, see “Special
Operation Methods,” page 48.
SLEEP Sleep Timer, page 21
FORMAT Picture shape (aspect ratio), page 24
MORE Clears the MORE menu.
-
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Basic Setup and Operation
9
TV Controls, continued
System Reset
TV Control Panel
If the TV fails to respond to the remote control, the
Buttons on the control panel duplicate some keys on
the remote control.
control-panel buttons, or will not power on/off, perform
System Reset. Recent setting changes made before
using System Reset may be lost.
•
Refer to upper labels when no TV menus are dis-
played.
To perform System Reset, press and hold the POWER
button on the control panel for ten seconds.
•
Refer to lower labels when using TV menus or after
activating a special function.
Panel-Lock Release
STATUS
POWER
•
•
To release the Panel Lock from the TV control
panel, press and hold the ACTIVITY button on the
control panel for ten seconds. You can release the
Panel Lock with the TV powered either on or off.
To activate the Panel Lock, use the Lock menu,
page 44.
737 and C9 series.
Flip open cover to
use buttons on the
front panel.
If You Power Off the TV by Mistake
1. Press POWER again, within about 60 seconds,
to have the TV come back on immediately.
2. If the status indicator starts rapidly blinking
green (about 60 seconds after you shut off
power), wait a few moments for the status indi-
cator to stop blinking and press POWER to turn
the TV on again.
Controls on 737 and C9 series TVs. 837 series controls
are similar and are located next to the STATUS indicator.
STATUS Light
Key
Off
Steady On
Slow Blinking
Fast Blinking
LED Color TV Condition
Additional Information
Normal operation.
TV is powered off.
TV is powered on.
None
Normal operation.
Green
Green
TV powered off, auto-on TV Timer
is set.
Normal operation. TV can be turned on at any time.
TV just powered off and lamp is
cooling.
LED starts to blink 60 seconds after turning off TV. TV can be
turned back on before blinking starts or after blinking stops, but
not while the indicator is blinking. Normal operation.
Green
Yellow
1. Lamp failure
Replace the lamp. See “Lamp-Cartridge Replacement and
Cleaning” on page 69.
2. No lamp installed.
Lamp access door is open or not
secure.
TV will not operate until lamp access door is secured. See
“Lamp-Cartridge Replacement and Cleaning” on page 69.
Red
Red
TV may require service.
Turn off the TV and unplug the set from the AC power source.
Wait one minute and then plug the set back in. See Appendix E.
If the red LED is still on, contact your dealer or a Mitsubishi
1-800-332-2119 to receive Authorized Service Center information.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
1. Basic Setup and Operation
Setting Up TV Inputs
Using the ANT (Antenna) Input
Setting Up Other Inputs
If using an antenna or direct cable service (no cable
box), connect the incoming coaxial cable to the TV’s
ANT input. Refer to page 18.
1. Connect your devices to the TV, making note of
which TV input jack is used for each device. See
“TV Connections,” page 14, for recommendations.
You must save channels to memory with a channel scan
to enable reception of all available high-definition and
standard-definition digital channels. The channel scan
will search for channels available locally. If you skip this
step, the TV will receive only analog channels.
2. Power on the devices to ensure detection.
3. Power on the TV.
The TV will display the New Device Found screen
for each new connection it detects Learn more
about Auto Input/Auto Output Sensing on the
opposite page.
Memorizing Channels with Channel Scan
For the ANT input
4. Select the device type if the device is not recog-
nized automatically.
To start channel memorization
1. Power on the TV.
2. Press MENU and open the Initial > Channel menu.
Start channel memorization from the Initial > Channel
menu.
3. Press ENTER to enter the menu.
4. Select Ant Air if connected to an
over-the-air antenna. Select Ant
Cable for direct cable.
5. Highlight Scan and press ENTER
.
Channel memorization may take up
to 15 minutes to complete.
Sample New Device
Found screen.
To stop channel memorization before completion,
press CANCEL
.
Important Note for NetCommand IR Users
837 Series. Be sure to select the correct device
type here. Although you can change the device type
later in the Inputs > Name menu, any “learned” Net-
Command IR codes will be erased when you make
the change.
Use the Initial > Channel > Edit menu (page 39) for
additional channel options, such as adding or deleting
channels from memory.
5. 837 Series. You can perform NetCommand IR
“learning” after selecting the device type or at a
later time when convenient. To perform now, high-
light NetCommand and press ENTER. See “Initial
NetCommand Setup,” page 47 or “Setting Up A/V
Receiver Control,” page 52.
6. Press BACK to close the New Device Found screen.
The TV will then display the New Device Found
screen for the next connection it finds.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Basic Setup and Operation
11
Setting Up TV Inputs, continued
-
For an HDMI A/V receiver, select AVR from
the list of device types if the A/V receiver is
not recognized automatically.
About Auto Input Sensing/
Auto Output Sensing
This TV’s Easy Connect™ Auto Input Sensing feature
detects most connections automatically.
•
HDMI CEC Devices Compatible with the TV’s
HDMI Control Feature. Compatible CEC-
enabled HDMI devices are often recognized auto-
matically by the TV. HDMI Control may allow you
to control some functions of a CEC-enabled device.
See Appendix C, “HDMI Control of CEC Devices.”
Auto Input/Auto Output Sensing for Most Devices
When you first connect a device, the TV will:
a. Detect the connected device and automati-
cally switch to it.
b. Prompt you to identify the device type.
c. 837 Series. Prompt you to perform NetCom-
mand set-up for the device, if available.
d. Repeat these steps for any other newly
detected devices.
Which Jacks Trigger Auto Sensing?
TV Jacks and
Auto Sensing
New Device Found screen for a device with HDMI
control enabled. Select On to enable the TV’s CEC
control of the device. In some cases, as in the
example above, you will also be prompted to select a
device name.
Y/VIDEO (detected as
9
composite video)
Y/VIDEO plus Pb (detected
as component video)
9
Tips on Auto Sensing
HDMI
9
•
•
Choose a different name for each input.
The antenna input (ANT) is never detected,
although you can turn off the unused antenna
input in the Inputs > Name menu.
USB (837 series)
9
DIGITAL AUDIO OUTPUT
(orange jack)
9
•
•
Change the device type displayed in the Activity
menu by using the Inputs > Name menu (page
40).
837 series. Any “learned” NetCommand IR
codes will be erased if you change the device
type in the Inputs > Name menu.
AVR AUDIO OUTPUT
red jack)
9
(
ANT (Antenna)
9
IR NetCommand Output
(837 series)
9
Reactivating Auto Input Sensing
for an HDMI Input
The TV cannot detect an HDMI device when
the device is powered off. Detection will
occur when the device is next powered on.
When you disconnect an HDMI device, Auto Input
Sensing is disabled until you perform these steps.
1. Disconnect the HDMI device.
When You First Connect a Device
2. Delete the removed HDMI device in the Inputs >
Name menu (see “Removing an HDMI Device,”
page 68).
•
Most Device Types. Select the device type from
the on-screen list. The device type you select here
will appear as a device icon in the Activity menu.
3. Connect the new device and the New Device
•
A/V Receiver
Found screen will display.
-
The TV can detect audio connections on the
DIGITAL AUDIO OUTPUT jack and the right (red)
AVR AUDIO OUTPUT jack.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
1. Basic Setup and Operation
Basic TV Operation
Selecting an Input to Watch
Watching DVDs or Videos
TV Connected to a DVD Player, DVR, or VCR
1. Press ACTIVITY
.
Press ACTIVITY and select a movie source from the
Activity menu. If you named devices during Auto Input
Sensing, select the input from the Watch Movie group.
2. Press
3. Press ENTER to switch to the input.
and to highlight an input.
Watching Broadcast TV
TV Connected to an Antenna, Direct Cable, Cable
Box, Set-Top Box, or Satellite Receiver
1. Select an input to watch from the Activity menu’s
Watch TV group.
Note: For more about the Activity menu, see page 21.
Activity menu, DVD input selected
Activity menu, antenna input selected
2. Tune to a channel.
•
Enter the channel number using the number
keys on the remote control and press ENTER
.
For a two-part digital channel, such as 3-1,
—
TV Tips
press
3
1
to enter a dash (separator).
CANCEL
•
•
•
Press CHANNEL UP/CHANNEL DN to change chan-
nels one channel at a time.
Turning the TV On or Off
•
Point the remote control at the front of the TV
and press the POWER button.
Press the POWER button on the TV control
panel.
Press
(LAST) to switch back to the previ-
ously tuned channel.
•
Antenna or Direct Cable Only. Press GUIDE to
display ChannelView channel listings, highlight
a channel number, and press ENTER to tune.
If You Turn Off the TV by Mistake
•
Press POWER again, within about 60 seconds,
to have the TV come back on immediately.
•
If the status indicator starts rapidly blinking
green (about 60 seconds after you shut off
power), wait a few moments for the status indi-
cator to stop blinking and press POWER to turn
the TV on again.
Controlling Sound Volume
•
Press VOLUME UP/VOLUME DN to adjust the sound
level.
•
See also “Controlling A/V Receiver Sound
Volume” on page 22.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Basic Setup and Operation
13
Basic TV Operation, continued
Making Picture Adjustments
Other TV Features
•
Activate Audio Lock to control your sound system
with the TV’s remote control left in TV mode. See
page 60.
1. To get the best picture under different viewing con-
ditions, set the Picture Mode before changing other
video settings. See page 35 for more.
•
To set the TV Clock see page 38. Set the TV
Clock if you plan to use the TV Timer (page 38) or
ChannelView (page 22) features.
a. Press MENU and go to the Adjust > Picture >
Picture Mode menu.
b. Make one of these selections:
•
•
To set parental controls, see the Lock menu, page
42.
Name
When to Use
Brilliant
Game
Bright
Natural
Under bright light
To change the input names that appear in the
Activity menu, see Inputs > Name options, page
40.
With gaming consoles
For most daytime viewing
For most nighttime viewing
•
•
3D Video. See page 25.
c. Press MENU to clear the menu.
To program the remote control to operate other
A/V devices, see Appendix B, “Programming the
Remote Control,” page 59.
2. Press MORE
.
3. Press
8
(VIDEO).
•
•
•
To control compatible devices using HDMI CEC
control, see Appendix C, “HDMI Control of CEC
Devices,” page 66.
4. Press
to display the name of the adjustment
you want.
5. Press
to make the adjustment.
837 Series. To view still and moving digital camera
images on the TV, see “Camera Images and Music
Files,” page 28.
Additional picture adjustments are described on pages
34 and 35.
837 Series. To control A/V devices with NetCom-
mand, see chapter 5, “NetCommand IR Control for
Most Devices” on (page 45).
Audio Settings
Changing the Audio Output
To switch audio output from the internal TV speakers to
a connected external sound system or headphones:
1. Press MORE
.
Other Information
2. Press
9
(AUDIO).
TV Care
3. Press
until the Speakers option is displayed.
The Speakers option will display only if a connec-
tion has been detected on one of the TV’s audio
outputs.
•
Lamp Cartridge. When the lamp cartridge needs
replacement, replace the lamp yourself and save
the cost of a service call. See Appendix D for
instructions.
4. Press to switch between TV and either AV
Receiver or Headphones.
•
General Cleaning. See “Cleaning Recommenda-
tions,” page 71.
Changing Audio Settings
Assistance
1. Press MORE
.
•
For troubleshooting, service, and product support,
see Appendix E, page 72.
2. Press (AUDIO).
9
3. Press
to display the name of the adjustment
•
For warranty information, see the TV warranty on
page 81.
you want.
4. Press
to change the setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
TV Connections
2
Before You Begin
Surround Sound
Auto Input Sensing
For best surround sound audio quality, route audio-
signal cables or HDMI cables from the source device
directly to your A/V receiver or sound system.
The TV’s Auto Input Sensing feature automatically rec-
ognizes most connections and prompts you to identify
the type of device connected. See page 11 for more on
Auto Input Sensing.
IMPORTANT
Connection Types
Accessory items such as cables, adapters,
splitters, or combiners required for TV
connections are not supplied with the TV.
These items are available at most electronics
stores.
Use the connection types available on your input
devices that will give the best video quality. For
example, choose HDMI over component video, and
choose component video over composite video.
Picture Quality
For best picture quality, route signals directly from the
input device to the TV whenever possible.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. TV Connections
15
Inputs and Outputs
Main Connection Panel
RS-232C control jack
offered on 837 series.
DVI/PC INPUT
ANT
(page 18)
1
6
(page 18)
10
RS-232C
DVI/PC INPUT
ANT
AUDIO
L
R
L
AVR
AUDIO
OUTPUT
3D
GLASSES
EMITTER
Y/ VIDEO
Pr
Pb
HDMI
2
R
1
3
3D GLASSES
EMITTER
5
(page 25)
Y/ VIDEO
Pr
(480i / 480p / 720p / 1080i)
Pb
R
L
DIGITAL
AUDIO
OUTPUT
R
AUDIO
IR-NetCommand
Output
2
8
4
3
9
7
Y Pb Pr
(component
video, page 17)
IR–NetCommand Output
AVR
AUDIO
OUTPUT
DIGITAL
AUDIO
OUTPUT
VIDEO
(composite
video, page 19)
HDMI
(page 17)
(page 46)
Offered on 837 series.
(page 20) (page 20)
Convenience Inputs
A readily accessible set of jacks is provided for a camcorder, game, or
other audio/video device.
Using an Audio-Only Device
837 Series. A fourth HDMI input is provided. If you connect a DVI
device to the HDMI input, use the nearby audio jacks to send sound
Keep an unused RCA-style con-
nector in the Y/VIDEO jack while
using an audio-only device.
from the device to the TV.
USB port and
HDMI 4 offered
on 837 series.
Unused
RCA-style plug
Y/VIDEO
L-AUDIO-R
(plug in first)
INPUT 3
Pr
Pb
Y/ VIDEO
L
R
AUDIO
USB
HDMI 4
1.
2.
3
Audio-only
device
11
2
Y Pb Pr
(component
video, page 17)
4
USB
(page 28)
HDMI
(page 17)
VIDEO
(composite video,
page 19)
Download from Www.Somanuals.com. All Manuals Search And Download.
16
2. TV Connections
Inputs and Outputs, continued
3. Y Pb Pr (Component Video)
Connect devices with component video outputs to this
1. ANT (Antenna)
Connect your main antenna or direct cable service (no
cable box) to ANT. The ANT input can receive digital
and analog over-the-air channels from a VHF/UHF
antenna or non-scrambled digital/analog cable source.
jack. Use the adjacent AUDIO R and
L
jacks if you wish
to send audio to the TV.
4. VIDEO (Composite Video)
2. HDMI™ Inputs (High-Definition
Multimedia Interface)
The HDMI inputs support uncompressed standard and
high-definition digital video formats and PCM digital
stereo audio.
Connect a VCR, DVD player, standard satellite receiver,
or other A/V device to the TV. Use the adjacent AUDIO
R
and
L
inputs if you wish to send audio to the TV.
5. 3D GLASSES EMITTER
Use this jack for the special IR emitter supplied with 3D
glasses. The emitter will send a signal that synchronizes
your 3D glasses with the screen display. See page 25
Mitsubishi recommends you use category 2 HDMI
cables, also called high-speed HDMI cables, to connect
HDMI 1.3 source devices. High-speed category 2 cables
bring you the full benefits of Deep Color and x.v.Color.
6. DVI/PC INPUT AUDIO
When connecting a DVI device to one of the TV’s HDMI
inputs, use these jacks for left and right analog audio.
These HDMI inputs can also accept digital DVI video
signals. To connect a device’s DVI output to the TV’s
HDMI input, use an HDMI-to-DVI adapter or cable plus
analog audio cables. Connect the analog audio cables to
the DVI/PC INPUT AUDIO jacks on the TV to receive left
and right stereo audio from your DVI device.
7. AVR AUDIO OUTPUT
Use AVR AUDIO OUTPUT to send analog audio of the
current program to an analog A/V surround sound
receiver or stereo system. Digital audio from digital
channels and HDMI devices is converted to analog
audio by the TV for output on this jack. This is the only
audio connection needed to the TV if using an analog
A/V receiver or stereo system.
Use the HDMI inputs to connect to CEA-861 HDMI com-
pliant devices such as a high-definition receiver or DVD
player. These inputs support 480i, 480p, 720p, 1080i,
and 1080p video formats.
The TV’s HDMI inputs are compatible with many DVI-D
and HDMI computer video signals.
Headphones. The audio right (red) jack can also be
used for headphones that accept standard line level
audio signals.
These inputs are HDCP (High-Bandwidth Digital Copy
Protection) compliant.
8. DIGITAL AUDIO OUTPUT
HDMI Cable Categories
This output sends Dolby Digital or PCM digital audio
to your digital A/V surround sound receiver. Incoming
analog audio is converted by the TV to PCM digital audio.
If you have a digital A/V receiver, in most cases this is the
only audio connection needed between the TV and your
A/V receiver.
HDMI cables are available as Category 1 and Cat-
egory 2 types.
•
Category 2 Cables (also called high-speed
HDMI cables). Newer, HDMI 1.3-compliant DVD
players, video games, and set-top boxes require
Category 2 cables, suitable for clock frequen-
cies up to 340 MHz or data rates of up to 10.2
gigabits per second. Use category 2 cables for
high-speed 1080p HD signals carrying extended
color encodings (i.e., 30 or more bits, also called
Deep Color). Category 2 cables are also suitable
for standard HDTV signals.
9. IR–NetCommand Output
837 Series. Connect IR emitters to this jack to send
control signals to external IR remote-controlled devices.
10. RS-232C
837 Series. Use the RS-232C interface to receive
control signals from compatible home-theater control
control signals for this interface.
•
Category 1 Cables (also called standard HDMI
cables). Category 1 cables may be unmarked.
They are suitable for standard HDTV 720p,
1080i, and 1080p signals with 8-bit color depth.
Use category 1 cables for clock frequencies up
to 74.25 MHz or data rates of up to 2.23 gigabits
per second.
11. USB (837 Series)
The TV can read JPEG photo files and mp3 or wma music
files from a USB device connected to the USB port.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. TV Connections
17
HDMI Device
Y Pb Pr Component Video Device
HDTV Cable Box, Satellite Receiver, DVD/
Blu-ray Player
HDTV Cable Box, Satellite Receiver, DVD/
Blu-ray Player
Required: HDMI-to-HDMI cable.
If your cable box or satellite receiver has an HDMI
output, use the connections for HDMI devices
described on this page.
Connect an HDMI cable from the TV back panel to the
HDMI device output. HDMI devices provide video and
audio through the single cable.
Required:
Mitsubishi recommends you use category 2 (high-
speed) HDMI cables to connect HDMI 1.3 source
devices. High-speed category 2 cables bring you the
full benefits of Deep Color and x.v.Color. See “HDMI
Cable Categories” on the opposite page for more on
HDMI cable types.
RCA-type component video cables
Left/right analog audio cables.
Note: To hear digital surround sound, connect the digital
audio output from the device directly to your digital
A/V receiver.
TV main
R
Y/ VIDEO
Pr
Pb
L
R
– AUDIO –
panel
RS-232C
DVI/PC INPUT
AUDIO
R
L
L
DVI/PC INPUT
AUDIO L
AUDIO
OUTPUT
ANT
R
Y/ VIDEO
Pb
Pr
R
L
AVR
AUDIO
OUTPUT
3D
GLASSES
EMITTER
Y/ VIDEO
Pb
Pr
HDMI
2
R
Y/ VIDEO
Pb
Pr
1
3
DIGITAL
AUDIO
OUTPUT
R
–
AUDIO
–
L
(480i
/
480p
/
720p
/
1080i)
R
IR-NetCmand
Output
Y/ VIDEO
Pb
Pr
R
DIGITAL
AUDIO
OUTPUT
R
L
(480i
/
480p
/
720p
/
1080i)
AUDIO
TV main panel
IR-NetCommand
Output
Component
video cables
Audio
cables
Incoming from
cable service or
satellite dish
AUDIO
HDMI-to-HDMI
cable
Any HDMI
device
L
Y
Pb
Pr
R
AUDIO
CABLE IN or
SATELLITE IN
Component video
device
IMPORTANT
HDMI and Audio Signals
Digital Surround Sound: The TV’s HDMI inputs
can receive digital stereo audio signals only. To
hear digital surround sound from an HDMI device,
connect the device’s HDMI or digital audio output
directly to your A/V receiver. See the Owner’s
Guides for those devices for instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
2. TV Connections
DVI Video Device
Antenna or Cable TV Service
Connect the incoming cable to the TV’s ANT input.
Cable Box, Satellite Receiver, DVD Player
Connect DVI devices (digital only) to the TV’s HDMI
input jacks.
VHF
antenna
Required:
Cable TV
service
Analog stereo audio cables
DVI-to-HDMI cable or DVI/HDMI adapter and HDMI
cable
UHF
antenna
If you are using a DVI/HDMI adapter, it is important to
connect the adapter to the DVI device for best perfor-
mance.
Some devices require connection to an analog input
first in order to view on-screen menus and to select DVI
as the ouput. Please review your equipment instruc-
tions for DVI connectivity and compatibility.
300-ohm-to75-
ohm combiner
(side view)
ANT
Note: The HDMI connection supports copy protection
(HDCP).
or
or
DVI/PC INPUT
AUDIO L
ANT
R
L
AVR
AUDIO
OUTPUT
3D
GLASSES
EMITTER
Y/ VIDEO
Pb
Pr
HDMI
2
ANT
R
1
3
3D
Pr
Older
cable
box
GLASSES
EMITTER
EO
Pb
Pr
R
DIGITAL
AUDIO
OUTPUT
(480i
/
480p
/
720p
/
1080i)
UDIO
IR-NetCommand
Output
TV main
panel
OUT
IN
Pr
R
p
/
1080i)
IR-NetCommand
Output
TV main panel
Not recommeded. Other
connection types provide
better quality audio and video.
DVI-to-HDMI
cable
Audio cables
R
L
DVI OUT
Digital DVI
device
AUDIO
RS-232C
TV main panel
Composite Video Device
DVI/PC INPUT
ANT
AUDIO
L
R
L
VR
O
Y/ VIDEO
3D
Y/ VIDEO
Pb
ASSES
MITTER
VCR or other device with composite video
output
3
Y/ VIDEO
Pb
R
L
R
(480i
/
480p
/
720p
/
1080i)
AUDIO
IR-NetCommand
Output
Required:
Composite video cable (usually yellow)
Analog stereo audio cables.
Composite
video cable
Audio
cables
VCR or other
device with
composite
L
R
COMPOSITE
VIDEO OUT
AUDIO OUT
video output
Download from Www.Somanuals.com. All Manuals Search And Download.
2. TV Connections
19
VCR or DVD Recorder to a Cable Box
Required:
VCR or DVD Recorder to an
Antenna or Wall Outlet Cable
Two-way RF splitter
Three coaxial cables
Required:
Right and left audio cables
Composite or component video cables
Video and audio cables required to connect the TV
to the cable box.
Two-way RF splitter
Two coaxial cables
Right and left analog audio cables
Component or composite video cables
Notes: Use composite video if only if component video
or HDMI are unavailable. For an HDMI connec-
tion between the TV and recorder, see page 17.
Note:
•
•
Use composite video only if component
video or HDMI are unavailable. For an
HDMI connection between the TV and
recorder, see page 17.
When using this connection configuration, it is
possible to view live cable programs through the
recording device. For best picture quality always
view live cable programs directly from the TV input
connected to the cable box device.
If your recording device has an analog-only
tuner, you must use a digital converter box
to enable recording of digital broadcasts.
RS-232C
ANT
AUDIO
L
R
TV main panel
L
AVR
AUDIO
OUTPUT
DVI/PC INPUT
AUDIO L
3D
GLASSES
EMITTER
ANT
Y/ VIDEO
Pb
Pr
R
HDMI
2
R
1
3
L
AVR
AUDIO
OUTPUT
3D
GLASSES
EMITTER
Y/ VIDEO
Pb
Pr
HDMI
R
Y/ VIDEO
Pb
Pr
L
R
(480i
/
480p
/
720
/
1080i)
AUDIO
IR-NetCommand
Output
Y/ VIDEO
Pb
Pr
DIGTAL
UDIO
OUTPUT
R
L
(480i
/
480p
/
720
/
1080i)
AUDIO
IR-NetCommand
Output
Y/ VIDEO
Y/ VIDEO
Pr
Pb
Y/ VIDEO
Y/ VIDEO
Pr
Pb
or
Cable
Box
Audio and
video from
cable box
or
IN
directly to TV
OUT
L
R
ANTENNA
IN
COMPOSITE
VIDEO OUT
COMPONENT
VIDEO OUT
AUDIO OUT
DVD Recorder or VCR
L
R
ANTENNA
IN
COMPOSITE
VIDEO OUT
COMPONENT
VIDEO OUT
AUDIO OUT
DVD Recorder or VCR
Download from Www.Somanuals.com. All Manuals Search And Download.
20
2. TV Connections
A/V Receiver
A/V Receiver with HDMI Output
Most setups require either a digital audio cable or
analog stereo audio cables. To send audio from TV
channels received on the ANT input or devices con-
nected directly to the TV, you must use one of the
connections shown below. Usually, only one of these
connections is required.
Required: One HDMI-to-HDMI cable
This option allows you to view content from devices
connected to an A/V receiver. The A/V receiver can
send audio and video to the TV over a single HDMI
cable. You can use an HDMI connection as described
here in addition to an audio connection from the TV’s
audio output. The optional audio connection allows you
to hear, through the A/V receiver, devices connected to
the TV only, e.g., an antenna on the ANT input.
The TV makes all audio available in digital and analog
formats:
•
Analog audio coming into the TV is available as
output in digital stereo format on the DIGITAL
AUDIO OUTPUT jack.
You may be able to use the TV’s remote control (in
TV mode) to operate connected CEC-enabled HDMI
devices. Experiment with your equipment to determine
which functions are available to the TV’s remote control.
See Appendix C, page 66.
•
Digital incoming audio is available as analog output
on the AVR AUDIO OUTPUT L and
R
jacks.
837 Series: This setup allows you to use NetCom-
mand-controlled audio and video switching over the
HDMI cable. See “Case 3: Automatic Audio and Video
Switching via HDMI” on page 54.
TV main panel
L
AVR
AUDIO
OUTPUT
R
RS-232C
DVI/PC INPUT
ANT
AUDIO
L
R
L
AVR
AUDIO
OUTPUT
3D
GLASSES
EMITTER
Y/ VIDEO
Pb
Pr
HDMI
R
Pb
Pr
R
DIGITAL
AUDIO
OUTPUT
480p
/
720p
/
1080i)
IR-NetCommand
Output
DVI/PC INPUT
ANT
DIGITAL
AUDIO
OUTPUT
L
TV main panel
AVR
AUDIO
OUTPUT
3D
GLASSES
EMITTER
HDMI
2
R
1
3
L
AVR
AUDIO
Stereo analog
cables
DIGITAL
AUDIO
OUTPUT
R
L
R
AUDIO
Net
ut
OUTPUT
Digital coaxial cable
(for a digital A/V
receiver)
(for an analog
A/V receiver)
DIGITAL
AUDIO
OUTPUT
Optional analog or
digital audio
connection
OPTICAL
COAXIAL
INPUT
A/V receiver
with HDMI
output
L
R
HDMI OUT
DIGITAL
AUDIO
A/V receiver back panel
Note:
VCR
High-definition
DVD player
•
On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from
the TV as a digital signal. To hear these copy-
protected signals through the A/V receiver, use
the connection for an analog A/V receiver.
DVD player
Cable box
•
Check the A/V receiver’s Owner’s Guide for
information concerning use of the digital input
and switching between digital sound and
analog stereo sound from the TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Using TV Features
3
Selecting an Input
The Activity menu lets you switch TV inputs. The inputs are
organized into groups based on possible ways to use them.
1. Press the ACTIVITY key.
2. Use
to move through groups of TV inputs.
3. Use
to select an input.
4. Press ENTER to switch to the input.
•
To change the list of inputs shown in each activity group,
see Inputs > Activity, page 40.
•
To assign or change the names of input icons, use the
Inputs > Name menu, page 40.
Sleep Timer
The Sleep Timer turns the TV off after the length of time you set.
To set the TV to turn on at a certain time of day, see the Initial > Timer menu on page
38.
Setting the Sleep Timer
1. Press MORE on the remote control. The TV’s MORE menu will display.
2. Press CANCEL (SLEEP) repeatedly to increase the time in 30-minute increments.
The maximum is 120 minutes.
SLEEP
3. Press BACK or wait five seconds without pressing any keys for the message to dis-
With the MORE menu
displayed, press the
CANCEL key on the
remote control to
activate/deactivate the
Sleep feature.
appear.
Viewing or Changing the Sleep Timer
1. Press MORE
.
2. Press CANCEL (SLEEP).
3. Press CANCEL (SLEEP) additional times to change the number of minutes before the
TV powers off.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
3. Using TV Features
ChannelView Channel Listings
Redirecting Audio Output
Selecting an Audio Output Device
1. Press MORE and then (AUDIO).
9
2. Press to show the Speakers option. The Speak-
ers option will display only if there is a connection
on a TV audio output.
3. Press to select either AV Receiver, Head-
phones, or TV.
Disconnecting an Analog A/V Receiver
When you disconnect an analog A/V receiver, change
the Speakers setting to TV to hear sound from the TV
speakers. Change the setting using the remote con-
trol’s MORE
Speakers menu.
>
9
(AUDIO )key or the Adjust > Audio >
ChannelView. Programs for the tuned channel are
listed on right side of screen.
ChannelView™ shows memorized channels on the ANT
input. It displays channel names and program informa-
tion for digital channels as sent by broadcasters or your
local cable service provider (information may be incom-
Controlling A/V Receiver Sound
Volume
Use one of the methods below to control sound volume from
an A/V receiver.
plete) No program information is displayed for analog
.
channels.
Note: You must set the TV Clock (page 38) to receive
With a Standard TV Setup
ChannelView listings for the current channel.
•
Recommended Method: Program the TV’s
remote control for your A/V receiver and enable the
Audio Lock feature. See page 60.
Using ChannelView
Feature
Instructions
•
Program the TV’s remote control for your A/V
receiver and set the TV remote control’s mode to
AUDIO. Return the control mode to TV to control the
TV.
Receive updates for a
digital channel.
1. Tune to the channel.
2. Press the INFO key.
Display/hide ChannelView
listings from the ANT
input.
GUIDE
•
Use the remote control that came with the A/V
receiver.
Scan channels one by one. Hold or
With HDMI Control (CEC-Enabled HDMI
A/V Receiver)
Scan channels quickly.
Hold PAGE UP/PAGE DN
Jump to listings for a spe- 1. Enter the channel
The TV’s remote control may control some functions of
the A/V receiver. See Appendix C, “HDMI Control of
CEC Devices,” page 66.
cific channel.
number.
2. Press ENTER
.
See more of the program
description for the current
channel (if available).
INFO
With NetCommand IR Control
837 Series. Set up NetCommand control of the A/V
receiver’s volume functions in the Inputs > AVR menu.
The TV’s remote will then control A/V receiver volume.
See page 52.
Tune to the highlighted
channel.
ENTER
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Using TV Features
23
Status Display
3
4
6
1
Press the INFO key to see
the on-screen status
display. The most
common displays are
shown here.
402-101 KABC
TV-PG DLSV
Monday Night Football
St. Louis vs. Tampa Bay, played in Tampa for
2
5
7
8
Sleep 30 min
12
Surround
13
Sample information
from the on-screen
status display
English
Tuesday 9:10 PM
HD 1080i Standard
9
10
11
14
ACTIVITY
GUIDE
About Channel Numbers
MENU
INFO
BACK
Channel Numbers for Over-the-Air Reception or
Reception by Direct Cable
Note: All signals are automatically converted to
1080p for display.
1. Current Input
Standard-Definition Analog Channels
2. Audio Indicator. Key:
Cable Reception
Channel 3
TV speakers
Headphones
External sound system
Mute
Cable
3
3. Channel number (antenna source only)
Digital channel includes major and sub-channel
numbers.
480i Stretch
Receiving Standard-Definition
Analog Signal (480i)
4. Digital channel name (if broadcast); antenna
source only.
Standard-Definition Digital Channels
5. V-Chip rating
•
•
Antenna source only for digital signal
Antenna or VIDEO composite jack for analog
signal
Over-the-Air
Antenna Reception
Main Channel 7
Sub-Channel 1
Ant
7-1 KABC-SD
6. Program name (if broadcast); digital source only
7. Program description (if broadcast); digital
source, antenna only. Press the INFO key additional
times to see more of the description.
SD 4:3 Stretch
Receiving Standard-Definition
Digital Signal (SD)
8. Sleep Timer remaining time
9. Day and time
High-Definition Digital Channels
10. Signal type being received
11. Screen format in use
Over-the-Air
Antenna Reception
Main Channel 7
Sub-Channel 1
Ant
7-1 KABC-HD
12. Program Audio indicator (antenna source only)
•
Digital source: Stereo, Surround, Dual Mono
•
Analog source: Stereo, Stereo SAP, SAP
HD 16:9 Stretch
13. Available language (digital source, antenna only)
Receiving High-Definition
Digital Signal (HD)
14. Signal-strength indicator (digital source,
antenna only)
Download from Www.Somanuals.com. All Manuals Search And Download.
24
3. Using TV Features
Original
Signal
TV Signals and Display Formats
TV
Display
This is a 16:9 widescreen TV suitable for images available
from HDTV and many DVDs. You can view older-style, squar-
ish images (4:3 aspect ratio) using one of the display formats
described on this page. Press the MORE key and then the
Anamorphic DVD
Recommended
Non-anamorphic or SD 4:3
Standard
Distorted.
Not recom-
mended.
0
key (FORMAT) to cycle through available display formats.
Expand
Zoom
Recom-
Distorted; not
recommended.
See Note 1.
mended for
letterbox. See
Note 1.
The TV remembers the format you last used for each input.
DVD Image Definitions
Image information may be stated on the DVD case. Some
DVDs support both of the formats described below.
Distorted.
Not recom-
mended. See
Note 1.
Recommended
for anamorphic
2.35:1 images.
See Note 1.
Anamorphic (or Enhanced for WideScreen TV)
Indicates DVDs recorded to show widescreen images prop-
erly on 16:9 TV sets using the TV’s Standard format mode
Stretch
Recom-
mended for
standard
broadcasts.
See Note 1.
Distorted; not
recommended.
See Note 1.
(recommended)
.
Non-Anamorphic (or 4:3, 1.33:1, Letter Box, or
Full Screen)
Indicates DVDs recorded for viewing on squarish TV
screens. They may be full screen (4:3 or 1.33:1) which
crops movies to fit the narrow TV, or letter box, which
adds black top and bottom bars.
Stretch
Plus
Recom-
mended for
standard
broadcasts.
See Note 1.
Distorted; not
recommended.
See Note 1.
Narrow
See Note 1
Distorted; not
recommended.
See Note 1.
Signal Definitions
480i: Older type of interlaced signals from the ANT input,
composite VIDEO, component Y Pb Pr, or HDMI jacks.
Note 1: Available for 480i, 480p, and digital SD 4:3 signals only.
Original Signal Display Formats
SD 16:9 or
480p: Progressive-scan DVD signals on component Y Pb
Pr or HDMI jacks.
Wide
Recommended to re-
HD Digital
Expand move side bars.
720p and 1080i: High-definition signals received through
component Y Pb Pr or HDMI jacks. These signals are
always 16:9 (widescreen).
720p, 1080i,
1080p Signal
Zoom Recommended to re-
move bars from the top,
bottom, and sides.
1080p: High-definition signals from a PC or Blu-ray player,
TV Display Formats. Press the MORE key and then
repeatedly press the key (FORMAT to see the displays
available for the current program. Press the INFO key to see
HDMI inputs only.
0
)
SD 4:3: Standard-definition squarish-screen-format
signals from digital channels on the ANT input.
the name of the display format in use.
SD 16:9: Standard-definition widescreen-format signals
from digital channels on the ANT input.
Stretch: Stretches a squarish 4:3 image across the
screen to display the entire image with less distortion
than the Standard format.
HD 16:9: High-definition 16:9 widescreen signals from
digital channels on the ANT input.
TV Display Format Definitions
Stretch Plus: Similar to Stretch, but minimizes distor-
tion on the sides by expanding the picture to crop off
Standard: The full-screen format used by HDTV signals.
Use this format to display anamorphic DVDs with a 1.78:1 or
1.85:1 aspect ratio. Anamorphic DVDs with a 2.35:1 aspect
ratio are displayed correctly but with top and bottom black
bars. Squarish (4:3) images are stretched evenly from side to
side. Available for all signals.
portions of the top and bottom. Use
vertical position of the picture.
to adjust the
Narrow: Displays narrow 4:3 images in their original
shape. Adds black side bars to fill the screen.
Wide Expand: Enlarges the picture, cropping the image
on both sides. Removes or reduces black side bars added
to narrow images converted to 16:9 signals for digital
broadcast.
Expand: Enlarges the picture to fill the screen by cropping
the top and bottom; useful for reducing the letter box top and
bottom bars of non-anamorphic DVD images.
Zoom: Enlarges the picture to fill the screen by cropping the
sides, top, and bottom to eliminate black bars.
Note: All high-definition channels send widescreen
(16:9) signals, but not all programming was created for
the widescreen format. The broadcaster may stretch
the image or add side bars to fill the widescreen area.
•
•
480i/480p and SD 4:3 signals: Eliminates top and bottom
bars on anamorphic DVDs with a 2.35:1 aspect ratio.
720p, 1080i, SD 16:9, and HD signals: Eliminates bars
added to squarish 4:3 images.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Using TV Features
25
3D Video
Watching 3D Video
Note: 3D glasses are required.
This section provides Instructions for viewing 3D
video using 3D glasses and the TV’s 3D feature. The
3D options are found in the Adjust > 3D Mode menu
described on page 34.
1. Press ACTIVITY
.
2. Highlight the icon for the 3D video device and press
ENTER
.
Initial Setup
3. Press MENU and select the Adjust > 3D Mode
1. Check if your HDMI 3D video source device outputs
a 1080p 60 Hz signal. This information will be
needed when you assign an input name in the New
Device Found screen.
menu.
4. Select On. The On setting will be memorized for
the current input when you exit this menu.
2. If your 3D glasses came with an emitter box,
connect the emitter box to the 3D GLASSES
EMITTER jack. Place the box in front of the TV
where there is an unobstructed path to the glasses.
RS-232C
DVI/PC INPUT
R
AUDIO L
ANT
L
AVR
AUDIO
OUTPUT
3D
GLASSES
EMITTER
Y/ VIDEO
Pb
Pr
HDMI
2
R
1
3
Y/ VIDEO
Pb
Pr
(480i
/
480p
/
720p
/
1080i)
R
IR-NetCommand
Output
3D
GLASSES
EMITTER
Use the Adjust > 3D Mode menu to enable 3D video.
5. Press BACK to close the menu.
6. If the image does not appear correct (e.g., objects
appear to be moving in instead of out), open the
Adjust > 3D Mode menu and set Glasses L-R to
Reverse.
3. Power on the TV and the source device.
4. Connect the source device to the TV’s HDMI input.
5. When the New Device Found screen displays,
To Watch Regular (non-3D) Video
name the input according to the table below.
The 3D Mode setting is memorized for each input.
When you want to watch non-3D video on the input
selected above, open the Adjust > 3D Mode menu and
set 3D Mode to Off.
The signal type and choice of name are important
because the TV will process the video signal
differently depending on the name you assign.
If your source device is a Blu-ray disc or game
console, the signal must be 1080p at 60 Hz.
Source
of 3D
Video
Assign
Name
3D Video Signal
Computer Recommended: 1080p 60 Hz
(1920 X 1080). The image will fill
the TV screen.
PC
Important Note About 3D Images
Other 60-Hz computer video
signals compatible with the TV
will display with black bars. See
“Computer Display Formats” on
page 27.
To display 3D images, Mitsubishi Home Theater DLP
TVs require that source devices support checker-
board display formats for 3D gaming or 3D cinema
content. A 3D standard format does not currently
exist for Blu-ray or DVD prepackaged media. Future
3D standards may be incompatible with Mitsubishi
Home Theater DLP TVs. Please visit mitsubishi-tv.
com for updates and information.
Any other
3D video
source
To see 3D video, the signal must Any
be 1080p 60 Hz
other
name
6. Press BACK to close the New Device Found screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
3. Using TV Features
Using the TV with a Personal Computer
Connecting a Computer to the TV
Use one of the connection methods listed below based
on your computer’s video output.
TV main
panel
ANT
3D
GLASSES
EMITTER
I
Pr
HDMI
2
1
3
I
P
1080i)
Computer
Video Output
Audio
Connection
R
IR-NetCommand
Output
Video Connection
Computer
with HDMI
audio and
video output
Digital DVI
DVI-to-HDMI cable Stereo audio
or an HDMI cable
with an HDMI-to-
DVI adapter
cables
An HDMI-to-HDMI connection carries all video and
audio on a single cable.
Note: If the computer’s audio output
is a single mini jack, a mini audio-to-
RCA-male “Y” adapter cable is also
required.
DVI/PC INPUT
AUDIO L
ANT
R
L
AVR
AUDIO
OUTPUT
3D
Y/ VIDEO
Pb
Pr
HDMI
HDMI-to-HDMI
cable
No additional
audio connec-
tion is required.
HDMI
2
GLASSES
EMITTER
R
1
3
Y/ VIDEO
Pb
Pr
R
DIGITAL
AUDIO
OUTPUT
(480i
/
480p
/
720p
/
1080i)
AUDIO
IR-NetCommand
Output
IMPORTANT
This TV accepts digital computer signals only.
TV main panel
1.
2.
1. Connect the computer’s digital signal output to one
of the TV’s HDMI jacks. See the connection dia-
grams for the method suited to your equipment.
2.
1.
2. Connect the computer’s audio output using one of
these options:
•
For digital DVI signals, connect analog left/right
audio to the TV’s DVI/PC INPUT AUDIO jacks.
For HDMI signals, no additional audio connec-
tion is required.
Computer with
DVI and stereo
audio outputs
DVI OUT
R
L
AUDIO
•
A DVI connection from a personal computer requires a
separate audio connection. A computer connected to
the TV main connector panel is shown above.
3. Power on the TV and computer. The TV will detect
the connection and display the New Device Found
screen.
4. In the New Device Found screen, press
to
Computer with DVI and
stereo audio outputs
highlight PC in the list of device types. It is impor-
tant to use the name PC so that the TV processes
the video signal correctly.
TV convenience inputs
AUDIO
INPUT 3
DVI OUT
Pr
Pb
Y/ VIDEO
L
R
USB
HDMI 4
AUDIO
L
R
5. Press BACK to close the New Device Found screen.
HDMI 4
HDMI-to-DVI cable
Note: If your computer provides digital audio out-
put (coaxial or optical), you can connect it
directly to a digital A/V receiver and bypass
the TV.
837 Series: Computer with DVI output connected to
the convenience panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Using TV Features
27
Using the TV with a Personal Computer
Computer Video Adjustments
Tip
1. Power on the computer.
Set the computer’s screen saver to display a pattern
after several minutes of inactivity. This acts as a
reminder that the TV is powered on and the lamp
is in use. The lamp is in use whenever the TV is
powered on, even if the screen appears dark.
2. Select PC from the Activity menu. To do this,
press ACTIVITY to open the Activity menu, move the
highlight to the PC icon, and press ENTER.
3. Working from the computer, change the resolution
of the computer image. View the computer image
on the TV and maximize the computer resolution
while maintaining a suitable aspect ratio for the
image.
Computer Display Formats
4. Perform TV video adjustments. Press
MORE then press (VIDEO) repeatedly
8
Press MORE then press
0
(FORMAT) repeatedly to cycle through the
to access video-adjustment options.
The following additional adjustments
are available for computer video:
TV displays available for your computer’s video signal.
Computer Signal
Original Format
As Displayed on TV Screen
Horiz Position (Horizontal Position).
Manually adjust the horizontal
position.
4 X 3
Standard
16 X 9
Zoom
Standard
VGA
Vert Position (Vertical Position).
640 X 480
Manually adjust the vertical position.
5. Press MORE then press (FORMAT)
0
WVGA
848 X 480
repeatedly to find the picture format
(aspect ratio) best suited to the image.
See the chart on this page showing
how different computer resolutions
can be displayed on the TV.
SVGA
800 X 600
Distortion in Computer Images
WSVGA
1064 X 600
Computer images may show distortion
when viewed on the TV, e.g., lines that
should be straight may appear slightly
curved.
Original Format
Standard
Zoom
XGA
1024 X 768
Image Resolution
Your Mitsubishi TV can display the resolu-
tions shown in the chart from standard
VGA (640 x 480) through 1920 x 1080
signals at a refresh rate of 60 Hz. The
resolution of 1920 x 1080 is supported at
refresh rates of 24, 30, and 60 Hz.
PC 720p
1280 X 720
WXGA
1360 X 768
In most cases, the computer will select
the best resolution match to display on
the TV. You can override this setting if you
wish. Refer to your computer operating
system’s instructions for information on
changing the screen resolution.
SXGA
1280 X 1024
Original Format
Standard
Reduce
PC 1080p
1920 X 1080
You may need to restart the computer for
changes to take effect.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
3. Using TV Features
Camera Images and Music Files
837 Series TVs Only
3. To use the USB Media Player menu:
•
The TV can read photo or music files from a USB
device. Photos must be in JPEG format and music
files must be in mp3 or wma formats. To play
music files while displaying a photo slide show, see
“USB Media Setup Menu” on the opposite page.
Activate any of the
menu options
Highlight an icon and press
ENTER
.
Display the Activity
menu.
Press ACTIVITY. Press again to
clear.
Display the main
menu.
Press MENU. Press again to
clear.
•
The TV can display files of still or moving images
from a camera through the Y/VIDEO port.
Display status for the Press INFO. Press BACK to
file source. clear.
The USB Media Player Menu
4. To resume use of the USB port after switching the
TV to a different input, press ACTIVITY, choose View
Photos, and select the USB port.
Playing a Slide Show or Playlist
Use these keys while playing a slide show or playlist.
Displaying the Menu
Replays the slide show or playlist.
or
ENTER
1. Back up the data on your USB drive before con-
necting it to the TV. Mitsubishi is not responsible
for any file damage or data loss.
Pauses a slide show or playlist.
2. Connect your USB card reader or USB drive to the
TV’s USB port.
Stops a slide show or playlist.
The USB Media Player menu displays while files
are being read. Wait until icons appear in the menu
before continuing.
Displays the previous or next slide.
Rotates an image clockwise in 90˚ incre-
ments.
GUIDE
INPUT 3
Pr
Pb
Y/ VIDEO
L
R
USB
HDMI 4
AUDIO
Displays the USB Media Player menu.
BACK
MENU
Displays the main menu.
Displays the Activity menu.
ACTIVITY
Displays slide name or track name. Press
BACK to clear.
INFO
IMPORTANT
Always stop playback with
to a different TV input before disconnecting your
USB device.
(STOP) or change
837 series TVs can read photo and
music files from the USB port.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Using TV Features
29
Camera Images and Music Files, continued
Thumbnail and Playlist
Menus
USB Media Setup Menu
Use the USB Media Setup menu set up play of a slide
show or playlist.
•
If JPEG image files and wma/mp3 files are on the
USB device, choose:
-
-
-
Slideshow + Music
Slideshow
Music only
JPEG Thumbnail Menu
•
•
Slideshow. Select either Auto or Manual advance
for the slide show. During manual operation, press
ENTER to advance to the next slide.
Use these keys while viewing JPEG thumbnail images
or the music tracks in a playlist.
Moves the highlight from item to item.
Interval. For automatic advance, select the time
interval for display of each slide. The interval you
select here is the minimum time between slides;
actual time may be longer for larger files.
Rotates a thumbnail clockwise in 90˚
increments
GUIDE
Plays the slide show or playlist starting
with the highlighted item.
or
ENTER
•
•
Frequency. For automatic advance, select the
number of times (frequency) to play the complete slide
show and/or playlist: Once, Twice, or Continuous.
Selects the last item on the current page.
Press BACK to close the Media Setup menu and
return to the Media Player menu.
Selects the first item on the current page.
Displays the next or previous page of
Notes on Using the USB Port
PAGE UP/DN items.
•
The TV ignores all commands while reading files. Wait
for icons to appear in the USB Media Player menu
before continuing.
BACK
MENU
Displays the USB Media Player menu.
Displays the main menu.
•
Large files or high-capacity storage devices may take a
long time to display. The screen will be blank while files
are read.
ACTIVITY Displays the Activity menu.
•
•
Use only one source device at a time.
USB Port Compatible Picture Files
Back up the data on your USB drive before connect-
ing it to the TV. Mitsubishi is not responsible for any
file damage or data loss.
•
Still images recorded on digital cameras using the
Exchangeable Image File Format, version 2.1 (EXIF
2.1) standard for digital still cameras and Design
Rules for Camera File Systems version 1.0 (DCF 1.0)
Note: Some manufacturers’ devices may be incompat-
ible with the TV. If the TV is unable to display your
photos, you can:
•
Some images opened and resaved on a computer
may not play back or may not display in the thumb-
nail list. This happens if the files were resaved in an
incompatible format.
•
•
Transfer files to a different USB device.
Use your digital camera’s composite video
output. See page 30.
•
•
Full path file names can be no longer than 50 char-
acters and must end in a .jpg extension. Only the
first 20 of the 50 characters will display.
The TV can read JPEG files as created by the
camera. If you edit a picture file on a computer
and resave the image, the TV may be unable to
read the resaved file.
Images on storage devices with a capacity of over
256 MB can take a longer initial time to display.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
3. Using TV Features
4. When the New Device Found screen displays,
Photos and Moving Video
as Composite Video
Connect the camera to the TV using a composite video
cable if:
assign the name Camcorder.
5. Press BACK to close the New Device Found screen.
6. Press ACTIVITY, select Watch Movie > Cam, and
press ENTER
.
•
•
You are unable to see images using the USB port.
You wish to view moving video from the camera.
Control the slide show or movie through the camera as
the TV’s USB Media Player menu will be unavailable.
The display resolution will be standard-definition (480i).
1. Refer to the owner’s manual supplied with the
camera for instructions needed for this setup.
2. Set the camera’s output signal type to NTSC and
put the camera into playback mode.
7. If viewing photos, advance through the images
manually or set the camera to advance automati-
cally.
3. With the camera still turned on, connect your digital
camera’s composite video cable (usually yellow) to
the TV’s Y/VIDEO jack. To hear audio, connect the
camera’s audio output cable to the AUDIO L jack.
INPUT 3
Pr
Pb
Y/ VIDEO
L
R
AUDIO
USB
HDMI 4
Optional
Audio Cable
Camera connection using a composite video cable
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Using TV Features
31
Introduction to Home-Theater Control
This TV offers a choice on home-theater-control systems. This summary offers some examples of the control
methods available using the TV’s remote control. You may wish to use one or more of these methods in your
home theater after completing Auto Input Sensing.
Source device connected directly to the TV
Remote Control Programming (Any Connection Type)
Program the remote control to operate the A/V device. To control the device, set
Any Connection Type
the remote control to the correct mode for the device type. See Appendix B, “Pro-
gramming the Remote Control.” In the case of an A/V receiver, use the Audio Lock
feature, page 60.
A/V
Device
TV
HDMI
Cable
CEC-Enabled HDMI Device (HDMI Connection Only)
See Appendix C, “HDMI Control of CEC Devices,” page 66.
CEC-Enabled
A/V Device
TV
Any Connection Type
A/V
837 Series: NetCommand IR Control (Any Connection Type)
Set up NetCommand IR control of the device’s keys as desired. See “IR Emitter
Placement,” page 46, and “Initial NetCommand Setup,” page 47.
TV
Device
Source device connected to an A/V receiver connected to the TV
CEC-Enabled
Source Device
A/V Receiver
TV
HDMI
Cable
CEC-Enabled HDMI A/V Receiver
The TV’s remote control may operate some functions of a connected A/V device.
You can switch to the device by selecting its icon in the TV’s Activity menu. See
Appendix C, “HDMI Control of CEC Devices,” page 66.
HDMI
Cable
Source
Device
Any Con-
nection Type
837 Series: A/V Receiver with HDMI Output (no CEC)
1. Set up NetCommand IR control of the A/V receiver’s keys as desired. See “IR
A/V Receiver
Emitter Placement,” page 46, and “Setting Up A/V Receiver Control,” page 52.
HDMI
Cable
2. Set up NetCommand IR control of the source device’s keys as desired. See
“NetCommand Control of a Device Connected to an HDMI A/V Receiver,” page
55.
TV
Download from Www.Somanuals.com. All Manuals Search And Download.
32
TV Menus
4
Main Menu
Press MENU on the remote control to open the main menu and then select from one of these categories.
Customize picture and sound settings.
33
37
38
40
42
Adjust
Captions
Initial
Turn closed captions on and off; customize caption displays.
Perform basic TV setup. Set language, scan (memorize) channels and edit
channel options, set the TV clock, set Lamp Mode, set auto-on TV Timer.
Assign names to TV inputs, enable HDMI Control, assign activities to inputs.
837 Series. Perform NetCommand IR “learning.”
Input
Restrict TV use. Disable the control-panel buttons. Set a pass code.
Lock
Menu Navigation
Displays or clears the main menu.
•
•
Moves up one menu level.
Clears the current menu.
•
Moves navigation into options
area.
•
Selects an item.
Moves the highlight within menus.
Makes adjustments in some
menus.
Look for the key guide at
the bottom of each menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. TV Menus
33
Adjust
Picture
Audio
Reset
See page 35 for picture adjustments.
See page 36 for audio adjustments.
•
•
Resets audio and picture adjustments for the current input. Highlight the Reset icon and press
ENTER twice
.
Reset has no effect on settings for Balance, Listen To, Language, Film Mode, and Advanced
Picture.
Global
Video Mute
(non-antenna
inputs only)
On
Displays a solid colored background when there is no video signal
from the current input. The colored screen reminds you that the
TV is powered on when there is no picture. The TV will power off
after five minutes without receiving a video signal.
Off
The screen appears black when there is no video signal from the
current input.
Audio
On, Off
Select On to display a random pattern while playing an audio-only
Screensaver
input. To use this feature, the input must be either
•
Named CD or MP3 Player and selected under the Listen
Music activity.
or
•
Be the ANT input.
Note: When playing an audio-only input, the TV will power off
after 12 hours of inactivity.
Film Mode
(480i and 1080i
signals only)
Auto, Off In Auto, the TV automatically detects and applies film-decoding cor-
rection to movies filmed at 24 frames per second. Try the Off setting
if images show many jagged edges.
Smooth 120Hz
Off, On
When On, Smooth 120Hz™ reduces motion blur in action scenes but
may show pixel structure during slower motion or in still images.
Blue Glow
On, Off
Select On to see blue accent lighting when the TV is powered on.
(837 series)
Displays a test picture for use by TV servicers.
Test Picture
Download from Www.Somanuals.com. All Manuals Search And Download.
34
4. TV Menus
Adjust, continued
Picture+
PerfectColor Sliders
Adjusts the saturation (intensity) of six colors for
the current image source.
PerfectTint Sliders
(837 series)
Adjusts six hues for the current image source
PerfectColor
Using PerfectColor:
Highlight the PerfectColor™ icon and press ENTER to display the PerfectColor menu. Settings are
retained independently for each TV input.
Using PerfecTint (837 Series):
•
To switch between PerfectColor™ and PerfecTint™ adjustments, highlight Adjust Mode and
press
Press
Press
.
•
•
•
•
to move from one color bar to the next.
to change settings.
Press CANCEL to restore default settings.
Press MENU to return to the main menu.
Advanced Picture allows you to save highly customized picture adjustments
for each input. Mitsubishi recommends a professional installer make
these adjustments.
Advanced
Picture
1. Press MENU. Under Picture+, highlight the Advanced Picture icon and press ENTER
2. With Picture Mode highlighted, press ENTER to change from blank (undefined) to ADV
837 Series: Choose ADV1 (daytime settings) or ADV2 (nighttime settings)
.
.
3. Use
4. Press
5. Use
to highlight an option you wish to change and press ENTER.
to change settings.
to navigate through the screen to additional options and press
to change settings.
6. Press MENU to close the menu. The Advanced Picture adjustments will be in effect for the
current input.
To use the custom Picture Mode at a later time
Press MENU and go to Adjust > Picture > Picture Mode and:
737 and C9 Series
837 Series
•
Select SPECIAL if settings were saved by
•
Select ISF Day or ISF Night if settings were
your professional installer.
saved by your professional installer.
•
Otherwise select ADV.
•
Otherwise select ADV1 or ADV2.
To return to the default values for Advanced Picture
Display the Picture+ > Advanced Picture menu and:
737 and C9 Series
837 Series
1. Highlight the Advanced Picture mode to change.
2. Highlight RESET Pic Mode and press ENTER
Repeat this separately for both ADV1 and ADV2.
Highlight RESET Pic Mode and press ENTER
.
.
3D Mode
3D Mode
On, Off
Use the On setting for video games and movies that require 3-D
glasses. This setting applies only to the current input.
Note: 3D options are available only for 1080p 60-Hz video
sources connected to an HDMI input.
Glasses L-R
Standard,
Reverse
Synchronizes the 3D glasses with the image on screen to provide
the best 3D effect. Try Reverse if Standard seems incorrect.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. TV Menus
35
Adjust, continued
Assign names to TV inputs before making
video adjustments (New Device Found or
Inputs > Name menu). Adjustments will be
reset to the defaults if you name or rename
inputs afterwards. To make picture adjust-
ments:
1. Press
2. Press
to highlight an option.
to adjust.
3. Press BACK when finished
While watching TV: Press the MORE key and then
(VIDEO) in the on-screen menu. Press to
.
Picture
•
8
select the video option you want to change. Press
•
From the Adjust > Picture menu:
to change settings.
Brilliant
For use under bright light; unavailable when the current
input is named Game or PC
Set the Picture Mode first
before changing other video
settings, as some settings are
stored independently for each
Picture Mode. Use Picture
Modes to get the best image
under different viewing condi-
tions.
.
Game
Optimizes picture and video processing for gaming
consoles. Available only when the name of the input is
Game or PC.
Picture
Mode
Bright
For most daytime viewing and x.v.Color sources
Natural
Special
For most nighttime viewing and x.v.Color sources
Advanced Picture Modes. Contact your professional installer for setup or see “Advanced Picture
”
on the opposite page
737, C9 series: Special/ADV
837 series: ISF Day/ADV1, ISF Night/ADV2
.
ISF Day,
ISF Night
•
•
•
Low contrast shows a variety of shades in darker images
In most home lighting situations, medium contrast looks best.
High contrast shows darker images more uniformly black and
makes colors appear more vibrant. High contrast is good for
brightly lit environments.
Adjusts the white-to-black level
Settings are stored indepen-
dently for each Picture Mode.
Contrast
Brightness
Color
Adjusts overall picture brightness. Settings are stored independently for each Picture Mode.
Adjusts overall color intensity from no color to fully saturated.
Adjusts the red-to-green ratio.
Tint
Sharpness
Adjusts picture detail and clarity.
High
Gives white images a cool cast. May provide the most
realistic picture under bright lighting.
Adjusts the white balance.
Settings are stored indepen-
dently for each Picture Mode.
Color
Temp
Low
Gives white images a warm cast. Natural/Color Temp
at the low setting displays video at approximately the
6500K industry standard for NTSC pictures.
High
Medium
Low
Use High with poor-quality signals.
Use Medium for moderate noise reduction.
Use Low with good-quality signals.
Use Off to leave the picture unaltered.
Reduces minor noise (graini-
ness) in the picture. Saved by
input. This adjustment is not
available if the current input is
named PC or Game or when 3D
is active.
Video
Noise
Off
On, Off
737, 837 Series. SharpEdge™ adds special edge enhancements to make the image
appear sharper. Saved by input.
SharpEdge
On, Off
Demo
737, 837 Series. DeepField™ Imager dynamically enhances black levels in portions of
the screen to provide strong contrast with detail over mixed screen content.
DeepField
Imager
For comparison, displays a split picture to show On (right side) and Off (left side).
Download from Www.Somanuals.com. All Manuals Search And Download.
36
4. TV Menus
Adjust, continued
To make audio adjustments:
•
From the Adjust > Audio menu:
1. Press
2. Press
to highlight an option
to adjust.
Audio
3. Press BACK when finished.
•
While watching TV: Press the MORE key and then
9
(AUDIO) in the on-screen menu. Press
the audio option you want to change. Press
change settings.
to select
to
Speakers
The Speakers option displays only if an A/V receiver or headphone connection has been
detected. Detection occurs on the right AVR AUDIO OUTPUT jack and the DIGITAL AUDIO OUT
jack. An A/V receiver can also be detected on an HDMI jack.
TV
Turns on the internal TV speakers.
AV Receiver
Turns off the TV speakers so you hear sound only from a connected A/V receiver.
Note: When you disconnect an analog A/V receiver, be sure to change the
Speakers setting to TV to hear sound from the TV speakers.
Headphones
Turns off the TV speakers so you hear sound only from connected headphones.
See “7. AVR AUDIO OUTPUT,” page 16. This option is not available if DIGITAL
AUDIO OUTPUT is connected.
Bass
Controls volume of low-pitched sound from the TV speakers.
Controls volume of high-pitched sound from the TV speakers.
Controls audio balance between the right and left TV speakers
Treble
Balance
Sound Mode
Stereo
No special audio effects from the TV speakers
Modifies audio from the TV speakers.
Surround
•
•
For monaural (non-stereo) programs, creates a simulated stereo effect.
For stereo programs, creates a simulated surround sound effect.
Listen To
Stereo
Mono
The TV plays stereo broadcasts in stereo and mono broadcasts in mono. The
word Stereo is displayed when you tune to a channel broadcasting in stereo.
Available only
for analog
channels from
the ANT input
Reduces background noise. Use when receiving a weak stereo audio signal. All
audio is played as mono with this setting.
SAP
(Second
Audio
Program)
Selects an additional monaural sound track not audible during normal TV viewing.
The SAP signal might be related to the program (such as a sound track in a foreign
language), or it might be unrelated (such as a weather report). If an SAP signal is
broadcast, the letters SAP are displayed when you tune to the channel.
Language
Selects the current language for a digital program from the ANT input. Each digital program may
include from zero to seven language choices.
Available only for digital channels from the ANT input.
Level Sound
On, Off
Reduces differences in sound volume between programming segments, such as
the difference between regular broadcast programs and commercial segments.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. TV Menus
37
Captions
IMPORTANT
Captions on Analog Channels
•
Analog text-service options display a large
black or gray box on the screen when no
signal is being broadcast.
The TV can decode captions from the ANT INPUT and
the composite VIDEO jacks. Broadcasters can send
either standard closed captions or text service. Standard
closed captions follow the dialogue of the program and
display in a small section of the screen. Text-service closed
captions often contain information such as weather or
news and cover a large portion of the screen.
•
The content of captions is determined by the
broadcaster. If captions show strange char-
acters, misspellings, or odd grammar, it is not
a malfunction of the TV.
•
Closed-caption signals are not available through
HDMI or component jacks. See the menus for
devices connected to these inputs for closed-
caption decoding.
Captions on Digital Channels
The TV can decode captions from the ANT input only.
Broadcasters can send up to six different captioning
selections or can send analog captions for a program
that originated in analog format. A TV station may broad-
cast only one or two types of captions or none at all
.
Services
Digital
Analog
On if Mute
Caption 1–
Caption 6
Off
•
On if Mute: Displays digital closed-caption signal Caption 1
when audio from the TV speakers is muted. When watching
TV, press MUTE to turn closed captions on/off.
Caption 1–Caption 6: Caption signals sent by the broad-
caster
•
•
On if Mute
CC 1–CC 4
Text 1–Text 4
Off
On if Mute: Displays analog closed captions signal CC 1
when audio from the TV speakers is muted. When watching
TV, press MUTE to turn captions on/off.
CC 1–CC 4: Standard closed-caption signals
Text 1–Text 4: Text-service signals
•
•
Analog Back- Gray, Black
ground
Selects either a gray or black text background to make analog
closed captions easier to read.
Effects
Font
Default
Font 1–Font 7
Default changes settings to those selected by the captions pro-
vider, or, if none, to the TV’s own caption defaults. Use Fonts 1
through 7 to give captions on digital channels a custom appear-
ance.
(for captions
from digital
channels)
Font Size
Large
Medium
Small
Large is the recommended size.
Font Color
White, Black, Magenta, etc.
Guidelines for setting digital captions:
Font Opacity
Translucent, Opaque, Flashing,
Transparent
•
A white font on a black translucent
background makes an easy-to-read
combination.
Use contrasting colors for captions and
background.
Background
Color
White, Black, Magenta, etc.
•
Background
Opacity
Translucent, Opaque, Flashing,
Transparent
Download from Www.Somanuals.com. All Manuals Search And Download.
38
4. TV Menus
Initial
Language
English
Spanish
Displays on-screen menus in either English or Spanish.
Note: To listen to audio in other languages (when available), see Adjust > Audio >
Listen To > SAP (analog signal) or Language (digital signal) on page 36.
Clock
Set the TV clock to:
•
•
Use the TV Timer to power on the TV automatically at a preset time
Receive correct updates to ChannelView listings
Note: When the Daylight Savings Time change occurs, you must open this menu and set the TV’s
clock ahead or back.
Time
1. With the hour highlighted, press
to change the hour and the AM/PM indicator.
Press and hold to change the hour display quickly.
2. Press ENTER to set the hour.
3. With the minutes highlighted, press
to change the minutes. Press and hold to
change the minutes display quickly.
Date
1. With the month highlighted, press
2. With the day highlighted, press
3. With the year highlighted, press
to select. Press ENTER to set.
to select. Press ENTER to set.
to select the current year.
Time Zone Eastern, Central, Mountain, Pacific, etc. The correct time zone is required for accurate
ChannelView updates.
DST
On, Off
Daylight Savings Time. Select the setting for your area. The
correct DST setting is required for accurate ChannelView updates.
Timer
Timer
On, Off
Select On to enable the Timer.
The Timer tells the TV to power on automatically at a time you set. Use this menu to set a day, time,
input, and channel for the Timer. If the TV is already on at the requested time, the TV will automati-
cally change to the designated channel or input.
•
•
The TV clock must be set before you can use the Timer feature.
To remind you that the TV Timer has been set, the POWER indicator on the front of the TV flashes
slowly while the TV is powered off.
•
When the Timer turns on the TV, press any key on the remote control to keep it on. Otherwise,
the TV will turn off after five minutes.
Day
Daily, Mon-Fri, (every) Sunday, (every) Monday, (every) Tuesday, etc.
Select the day or days of the week for the Timer to turn on the TV.
Time
To set the time for the TV to come on:
4. With the hour highlighted, press
repeatedly to change the hour and the AM/
PM indicator. Press and hold to change the hour display quickly.
5. Press ENTER to highlight the minutes.
6. Press
to change the minutes. Press and hold to change the minutes display quickly.
Input
Ant, DVD, VCR, etc.
Select the input you want displayed when the TV comes on. Choose from the defined
and enabled inputs that appear in the Activity menu.
Channel
If the source is the ANT input, select a channel number by pressing
or press and
hold to scroll through channels.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. TV Menus
39
Initial, continued
Channel
Ant Air,
Ant Cable
You must perform a channel scan to receive digital channels. Scan searches for broad-
cast channels and adds them to TV memory. To start channel scan
1. Highlight one of the input selections based on your connection to the ANT input
:
:
Scan
•
Air when connected to an indoor or outdoor antenna.
•
Cable when connected to direct cable (no cable box)
(Channel
Manage-
ment)
2. Press to highlight SCAN.
3. Press ENTER to start channel memorization.
Edit
After channel scan, Edit lets you add and delete memorized channels.
•
•
Press PAGE DN/UP to jump to the next or previous page of channel numbers.
Press to move through all channel numbers, one at a time.
3. Use the number keys and CANCEL key to enter
the physical channel number followed by “-1”
and ENTER. For example, for physical channel
36, press
Notes on Scan and channel memorization
•
•
•
•
Channel memorization may take up to 15 minutes
to complete.
To stop channel memorization before completion,
ENTER
.
3
6
1
press CANCEL Channels already added are retained.
.
The TV will search for a digital channel on the channel
36 frequency. When it finds the channel, it will:
When watching TV, press CH
to move through
memorized channels.
a. Add the channel to memory.
b. Change the channel number to the virtual
channel number sent by the broadcaster.
c. Add to memory any associated sub-
channels.
To add a digital channel that does not appear in the
Edit menu without repeating channel memorization:
1. Look up the physical channel number for
the new digital channel. See the website
www.antennaweb.org for help.
•
Rememorize channels if you move the TV to a differ-
ent geographic area with a different channel line-up.
2. Press ACTIVITY and select the ANT input.
Adding/Deleting Channels Using the Channel Edit Menu
•
•
•
•
Channels marked with a check are in memory.
To add or delete a channel from memory, highlight the channel number and press ENTER
To add a single digital channel not in the list, see the notes under Scan on this page.
Digital channels are listed by virtual channel number with the physical channel number shown in small gray text.
.
See below for an explanation of these terms.
-
-
Virtual Channel Number (digital channels only). A channel number sent by a local broadcaster. Usually the
virtual number is associated with the corresponding analog channel number. For example, a broadcaster may
associate digital channel 2-1 with their analog channel 2.
Physical Digital Channel Number. The channel number officially assigned to the actual broadcast frequency;
shown on screen in gray text.
Lamp
Lamp
Standard, Standard is for most viewing conditions. Use Bright in brightly lit rooms.
Bright You may notice increased fan noise when using the Bright setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
40
4. TV Menus
Inputs
Name
Cablebox, Cam(corder), CD, DVD
•
Lets you assign or change names of inputs appearing in
(DVD, DVD2, Blu-ray), DVR, Game
(Game, PS, Xbox, Wii), MP3 Player,
PC, Satellite, VCR, AVR
the Activity menu.
-
-
-
Press
Press
to move between inputs.
to select a name.
You cannot change the name of the current input; you
must first switch to another input. If you have only one
input, such as a cable box, make sure the Ant input is
On and switch to Antenna in the Activity menu before
renaming the single input.
Delete (deactivated HDMI only)
On/Off (ANT only)
•
Lets you turn the Ant input On/Off (to display/hide it in the Activ-
ity menu).
•
•
Lets you delete unused HDMI inputs from the Activity menu.
A CEC-enabled tuner can be named either Cable Box or
Satellite
A CEC-enabled DVD player can be named DVD
Blu-ray.
.
•
,
DVD2, or
General Notes
When you change an input name in the Name menu and then exit the Name menu:
•
•
•
•
The name is changed
The icon in the Activity menu is changed
Audio and video settings are changed to the defaults for the new device type.
837 Series: All previous NetCommand IR “learning” for the input is erased.
Notes for HDMI devices
•
Disconnecting an HDMI device: When you disconnect an HDMI device, the icon remains in the Activity menu until
you remove it. Select Delete in the Inputs > Name menu to remove an unwanted icon for an HDMI input.
•
If the New Device Found screen does not display as expected when you connect an HDMI device, see “Reac-
tivating Auto Input Sensing for an HDMI Input,” page 11.
•
•
HDMI Control and CEC-Enabled Devices: See Appendix C, “HDMI Control of CEC Devices,” page 66.
If case of CEC conflicts: Turn off CEC signals in one of these ways:
-
-
Turn off the TV’s HDMI Control signals to the device.
Turn off each device’s internal CEC capability.
See Appendix C for the TV’s HDMI Control or, to turn on/off a specific device’s response to CEC signals, see
the device owner’s manual.
Learn
AVR
837 Series
Sets up or changes NetCommand IR control of the current viewing device.
See “About NetCommand IR Control,” page 45.
837 Series
Sets up or changes NetCommand IR control of an A/V receiver.
See “NetCommand IR Control of an A/V Receiver” on page 51.
HDMI Control
Activity
On, Off
Select On or Off to enable or disable the TV’s control of a CEC-enabled device.
See Appendix C for use of this feature.
•
•
•
Lets you customize the Activity menu choices for the current input.
Highlight the activity name and press ENTER to make changes.
See “How is the Activity Menu Generated?” on the opposite page.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. TV Menus
41
Inputs, continued
How is the Activity Menu Generated?
The TV automatically generates the Activity menu
based on recognized inputs. If the inputs have been
named as device types, the TV groups the device types
based on how they can be used. The device names
used for groupings are those assigned in the New
Device Found menu or the Inputs > Name menu. The
table below summarizes the device groupings that can
appear in the Activity menu.
Key
Activity assignments made automatically by the TV.
X
Activity assignments you can make using the
Inputs > Activity menu.
Watch Watch
Play
View
Listen
TV
9
9
Movie Game Photos Music
Antenna
AV Receiver
Blu-ray
Cable Box
Camcorder
CD/Audio
DVD
9
X
X
9
9
9
9
X
9
9
DVD2
X
DVR
9
Game
9
9
MP3 Player
PC
9
9
X
X
X
X
9
9
PS
9 9
Satellite
USB
X
9
VCR
9
Wii
X
9
9
Xbox
X
Download from Www.Somanuals.com. All Manuals Search And Download.
42
4. TV Menus
Lock
TV Locks
Parental Menu
The TV comes from the factory with the rating locks
turned off and with pre-set U.S. ratings TV-PG and
movie rating PG. Turn on blocking for U.S. ratings
to activate these rating restrictions. Use the Lock >
Parental menu to change the level of blocking with U.S.
ratings.
Parental Lock by Program Ratings
Restricts access using U.S.-based ratings
sent by broadcasters.
Time
Lock by Time
Restricts TV use by time of day.
Any time you change the channel or device, it may take
up to five seconds for the rating restrictions to take
effect.
Panel
Lock Control Panel
Disables the buttons on the TV’s control
panel. Use this option if small children
in the home try to press control-panel
buttons.
Other Menu (Alternate Rating System)
Other
Lock by Other Program Ratings
Restricts access using non-U.S.-based
ratings sent by broadcasters.
This TV can recognize new rating systems that may
come into effect in the future. The Other menu allows
you to block digital programming when such systems
come into effect.
The first time you tune to a channel broadcasting an
alternate rating system, the TV defaults to the most
restrictive setting if the Lock menu > Other Lock
option is set to On. Use this menu to change the
allowed rating if you are unable to watch a program
rated with an alternate system.
Pass Codes
Setting a Pass Code
You are prompted to enter a pass code whenever you
select Lock on the main menu. To set a pass code for
the first time:
1. Press MENU and highlight Lock. A screen prompt-
ing you for a pass code will display.
Bypassing TV Locks
2. Input a four-digit pass code using the number keys
•
If you try to watch a blocked program or the TV is
locked by time, a notice will appear prompting you
for a pass code. To use the TV, input your four-digit
on the remote control.
•
•
Press CANCEL to delete a number and move
back one space.
pass code and press ENTER
.
Press MENU or BACK to close the menu without
-
To reactivate the locks after using a pass code,
setting a pass code.
power the TV off and then on.
-
To reactivate only the parent ratings lock,
change to a different channel or device.
3. Press ENTER to set the pass code.
Resetting a Pass Code
•
If a program is blocked, you can still use the TV
without entering a pass code. Change to a channel
airing an allowed program or change to another
device.
See the procedure in Appendix A.
Important Notes on Rating Locks
•
Parental menu rating locks apply only to chan-
nels and signals received on the ANT and com-
posite VIDEO jacks.
•
•
Other menu rating locks apply only to digital chan-
nels received on ANT
.
When viewing a cable box, satellite receiver,
or other device connected to the component
Y Pb Pr or HDMI inputs, check the device’s
owner’s guide for parental locks.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. TV Menus
43
Lock, continued
Parental
Lock
Off, On
Disables or enables blocking based on V-Chip signals and the U.S. rating system.
Start
Time
Sets the time of day for enforcement of rating restrictions set in the Parental menu.
1. Highlight the hour digits for Start Time.
Stop
Time
2. Press
repeatedly to change the hour and associated AM/PM indicator. You can also just press
and hold to move quickly through the numbers.
3. Press ENTER to highlight the minutes.
4. With the minutes digits highlighted, press
repeatedly to change the minutes. You can also just
press and hold to move quickly through the numbers.
5. Highlight the Stop Time digits and set the time as described above.
Note: To make rating restrictions active 24 hours a day, make Start Time and Stop Time the same.
TV
Rating
TV-Y
Youth. For children under 7.
Youth 7 and older.
Highlight the rating level
you wish to change and
press ENTER to block it
TV-Y7
TV-G
TV-PG
General Audience. For the entire family.
(
) or allow it ( ).
You can apply supple-
mental content blocking
to the age-based ratings
by using the TV content
categories listed below.
Parental Guidance. Parental Guidance recommended; may
not be suitable for some children.
TV-14
Adolescent 14 and older. Not recommended for children under 14.
TV-MA
Mature Audience. For adults only.
FV
D
L
Fantasy Violence. Applies to TV-Y7 only.
Sexual Dialog. Applies in differing degrees to TV-PG and TV-14.
Adult Language. Applies in differing degrees to TV-PG, TV-14, and TV-MA.
Sexual Situations. Applies in differing degrees to TV-PG, TV-14, and TV-MA.
TV Content
Categories
S
V
Violence (graphic or realistic). Applies in differing degrees to TV-PG,
TV-14, and TV-MA.
Movie
Rating
G
General Audience. Designed for the entire family.
PG
PG-13
R
Parental Guidance. Parental Guidance recommended; may not be suitable for some children.
Parental Guidance, 13 and Older. Not recommended for children under 13.
Restricted. Restricted in theaters to 17 years old and older unless accompanied by an adult.
No Children 17 or Under. Restricted in theaters to 18 years old and older.
Adult. Designed for and restricted in theaters to adult audiences only.
NC-17
X
Not Rated No MPAA rating assigned
Download from Www.Somanuals.com. All Manuals Search And Download.
44
4. TV Menus
Lock, continued
Blocks all use of the TV during the time period you specify. You must enter a pass code to use the
TV when the time lock is in effect.
Time
Lock by Time Enables/disables Lock by Time.
Lock Time,
To set the lock and unlock times:
Unlock Time
1. Highlight the hour digits for the Lock Time.
2. Press
move quickly through the numbers, just press and hold.
3. Press ENTER to set the hour and highlight the minutes.
repeatedly to change the hour and associated AM/PM indicator. To
4. With the minutes highlighted, press
repeatedly to change the minutes. To
move quickly through the numbers, just press and hold.
5. Highlight the Unlock Time digits and set the time as described above.
Note:
To make Lock by Time active 24 hours a day, make Start Time and Stop Time
the same.
Off, On
On locks and Off unlocks the buttons on the TV’s control panel. Use this option if
small children try to press TV buttons.
Panel
Other
•
To release the Panel Lock from the TV’s control panel, press and hold the
ACTIVITY button for ten seconds. If the TV is powered off, press POWER after the
lock releases to make the TV power on.
•
To reactivate the lock, return to this menu and change the setting to On.
Other Menu Options (alternate rating system)
This TV can recognize new rating systems that may come into effect in the future. The Other option
remains grayed out until the TV receives a signal using an alternate rating system. Such alternate
rating systems will apply only to digital programming received on the ANT input.
Lock
On, Off
Enables/disables program blocking.
System Name The rating system available for the channel
Group
Rating
Rating groups available in the rating system shown on the screen. Rating groups are
defined by the rating system in effect.
Rating restrictions available in the selected rating system and group. Highlight the
rating and press ENTER to check (block) or uncheck (allow) rated content.
Download from Www.Somanuals.com. All Manuals Search And Download.
45
NetCommand IR Control
5
About NetCommand IR Control
•
•
NetCommand IR home-theater control is avail-
able on 837 series models.
•
•
NetCommand operates by sending remote control
signals from the TV to your other devices via the
IR (infrared) emitters, telling the devices to play,
record, change inputs, adjust volume, change chan-
nels, or perform other functions. All this is accom-
plished with the TV’s remote control left in TV mode.
IR emitter cables are available for purchase
800-553-7278 and request one of the following:
-
242D483020 (two-ended cable)
You may wish to use NetCommand IR control to
supplement control of CEC-enabled devices.
-
299P254020 (four-ended cable).
•
•
NetCommand setup is optional.
Important Note on NetCommand
You can perform NetCommand setup when the TV
first recognizes a device during Auto Input Sensing
or at any convenient time afterward.
Be sure to connect the IR emitter cable to the
TV and properly place the emitters so that
NetCommand can control your devices.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
5. NetCommand IR Control (837 Series)
IR Emitter Placement
The NetCommand system uses emitters connected
to the IR NetCommand Output jack to control other
Other A/V Device
–
devices such as DVD players, cable boxes, satellite
receivers, and VCRs.
S
CH
R
IR emitter cables are available for purchase from
Mitsubishi. Request either part number 242D483020
(two-ended cable) or part number 299P254020 (four-
ended cable).
D
S
I
G
I
T
A
L
IR-NetCommand
Output
R
R
O
U
N
D
A/V Receiver
DVI/PC INPUT
AUDIO L
ANT
R
L
AVR
AUDIO
OUTPUT
3D
GLASSES
EMITTER
Y/ VIDEO
Pb
Pr
HDMI
2
TV Main
Panel
R
1
3
Y/ VIDEO
Pb
P
R
L
(480i
/
480p
/
720p
/
1080i)
AUDIO
IR-NetCommand
Output
1. Connect the plug end of the supplied IR emitter
cable to the IR—NetCommand Output jack on the
TV back panel.
Connecting IR–NetCommand Output
2. When the New Device Found screen displays,
*OꢀGSPOUꢀPGꢀBꢀTJOHMFꢀ
BWFSBHFꢁTJ[FEꢀEFWJDF
*3ꢀTFOTPSꢀ
highlight EXIT and press ENTER
.
0OꢀUPQꢀPGꢀBꢀTJOHMFꢀ
UBMMꢀEFWJDF
*3ꢀTFOTPSꢀ
*3ꢀTFOTPSꢀ
*3ꢀTFOTPSꢀ
*OꢀGSPOUꢂꢀTIBSFEꢀCZꢀ
UXPꢀBWFSBHFꢁTJ[FEꢀ
EFWJDFT
Place IR emitters so the signal can be “seen” by the IR
sensor on each device.
The New Device Found screen displays when you
connect the IR emitter.
If You are Unable to Locate
a Device’s IR Sensor
3. Position the emitter end with the emitter bulb facing
the device’s remote control sensor. The bulb emits
infrared light in a cone-shaped pattern. Place the
bulb far enough from the sensor to allow the cone
pattern to reach the sensor.
•
The IR sensor is usually behind the plastic window
of the front display panel. Using a flashlight, you
may be able to see it as a round or square cutout.
•
If you cannot see the sensor and the device’s
Owner’s Guide does not specify the location, do
the following using the device’s remote control.
In some cases, the emitter works better facing
downward from the top of the device. Experiment
to find what works best.
1. Starting at one end of the plastic window, hold
the device’s remote control about one-half
inch from the front of the device and press the
POWER key.
4. Secure the emitter ends in place using double-
sided tape.
2. If the device does not respond, move the
remote control one inch toward the center and
try again. Repeat until the device responds.
5. Place any unused ends behind the devices to
prevent stray signals from reaching the IR sensors.
3. Repeat the previous steps starting at the other
end of the window. The sensor will be between
these two points.
IMPORTANT
Position IR emitters so that each device’s
sensor “sees” the signal from only one emitter.
Otherwise, a device receiving signals from
multiple sources (remote controls, IR emitters)
may not respond at all.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. NetCommand IR Control (837 Series)
47
Initial NetCommand Setup
To perform this procedure, you need:
•
The remote controls for both the TV and the
device you want to control.
•
An IR emitter cable available from Mitsubishi
.
Note: To set up an A/V receiver, see “Setting Up A/V
Receiver Control,” page 52.
1. Connect and position the IR emitters for the
devices you wish to control. See “IR Emitter Place-
ment” on the opposite page.
2. Set the TV’s remote control to TV mode and power
From the New Device Found screen, highlight
NetCommand and press ENTER to open the Learn
screen.
on the TV.
3. Open the NetCommand Learn screen as follows:
•
If working from the New Device Found screen
after the device is first detected, highlight
NetCommand and press ENTER to open the
Learn screen for the device.
Device-specific keys in the
rightmost column can be accessed
with the MORE key after “learning.”
•
If performing NetCommand setup at any time
after the device has been recognized through
Auto Input Sensing:
a. Press ACTIVITY.
b. Highlight the desired input icon and press
ENTER to switch to that input.
c. Press MENU, highlight Inputs, and highlight
Learn to open the Inputs > Learn screen
for the device.
4. The first function highlighted in the Learn screen
is always Power On. Aim the TV’s remote control
at the TV and press ENTER to begin learning for that
function.
Inputs > Learn screen
5. When the Power On text starts flashing, aim the
device’s remote control at the TV and hold the POWER
key until a check mark appears next to Power On.
Key names marked with a
check have been “learned.”
•
If the text stops flashing before the check mark
appears, repeat the previous step.
•
To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
Adding or Removing Device Keys from
NetCommand Control
6. Press the
keys on the TV’s remote control
1. Switch the TV to the device. Press ACTIVITY, high-
light the device’s icon, and press ENTER
to highlight other keys on the list. Repeat steps
4 and 5 for each additional function you wish to
control through NetCommand.
.
2. Open the Inputs menu and highlight the Learn icon.
3. When the Learn screen displays:
Note: Device keys in the far right column will be asso-
ciated with the remote control’s MORE key when
“learned.” See the table on page 49.
•
To add keys: Continue as described earlier
under “Initial NetCommand Setup” on this
page.
7. If the device has a separate POWER OFF key, press
on the TV’s remote to highlight Power Off.
•
To delete keys: Highlight the name of the key
you wish to delete and press CANCEL on the
TV‘s remote control to clear the check mark.
Repeat the earlier steps to “learn” the POWER OFF key.
If the device has no POWER OFF key, skip this step.
8. Press BACK to finish NetCommand “learning” for the
current device.
Download from Www.Somanuals.com. All Manuals Search And Download.
48
5. NetCommand IR Control (837 Series)
Operating NetCommand-Controlled Devices
Controlling Most Device Types
Note: if you have set up automatic input switching for
the A/V receiver, the A/V receiver will automati-
cally switch to the correct input for the device.
As an example of NetCommand control, if you are
watching your cable box and you wish to tune to the
next channel higher, press CHANNEL UP. NetCommand
then sends the “learned” channel-up control signal to
the cable box.
5. To operate the device using the TV’s remote
control, press the side button to put the remote
control into TV mode.
6. Point the remote control at the TV (not the device)
1. Perform NetCommand setup for the device as
and press the key for the desired function.
described in this chapter.
7. Press the MORE key to access additional key func-
2. When you wish to use the device, press ACTIVITY
3. Press to highlight the icon for the device.
.
tions you may have “learned” for the device.
4. Press ENTER to switch the TV to the device.
Special Operation Methods
Key Name in
Learning Screen
Special Operation Description and Setup
How to Use
Power On
Manual Power On/Off
1. Press ACTIVITY.
Use for devices that have only one POWER key.
2. Press
to highlight the icon for the
device to be powered on or off.
3. With the Activity menu still displayed, press
POWER to send the power signal; you may
need to press POWER twice.
Note: If you press POWER without the Activity
menu displayed, the TV will turn off.
4. Press ENTER to switch the TV to the device.
Power On
Power Off
Automatic Power On/Off
•
To Power On the Device
This feature is only for devices that have separate
POWER ON and POWER OFF keys on their original
remote controls. If your device does not have a
separate POWER OFF key, do not use the Power
Off learning position; use only the Manual Power
ON/OFF method described above.
1. Press ACTIVITY.
2. Press
to highlight the icon for
the device to be powered on or off.
3. Press ENTER to switch the TV to the
device and NetCommand will send the
Power On command to the device.
In the NetCommand Learn screen:
•
To Power Off the Device
When you turn the TV off, the TV sends all
learned Power Off commands to all devices.
a. “Learn” the Power On command in the
Power On learning position.
b. “Learn” the Power Off command in the
Power Off learning position.
Menu
Guide
Displaying a Menu for the Current Device
Press MORE and then
command to the current device.
1
to send the menu
“Learn” the MENU key on the original remote in the
Menu learning position.
Displaying the On-Screen Program Guide
(cable box or satellite receiver)
1. While watching the device, press GUIDE to
display the guide.
2. Press PAGE UP/DOWN
(
) to send the Page
1. “Learn” the GUIDE key on the original remote in
Up/Dn commands for the guide.
the Guide learning position.
2. Learn the PAGE UP and PAGE DOWN keys of the
original remote in the Page Up and Page
Down learning positions.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. NetCommand IR Control (837 Series)
49
Key Name in
Learning Screen
Special Operation Description and Setup
How to Use
Enter
ENTER-Key Functions (cable boxes, satellite receivers, etc.)
Some devices have two keys that have “enter” functions. One key is for menus and is often labelled
SELECT or OK. A second key is for use with number keys for direct channel selection. NetCommand
uses the same ENTER key for both operations.
When ENTER has a menu or guide function or
when the original remote control uses the same
key for menus and channel selection:
1. Press MENU or GUIDE to display the device’s
menu or guide.
2. Press ENTER within the menu and
NetCommand will send the Enter signal for
menus.
Learn the ENTER
,
SELECT, or OK key in the
NetCommand Enter learning position.
Enter (digits) When ENTER is for channel changes, i.e., the origi- Press digit key(s) and then press ENTER
.
nal remote control has a separate ENTER key for
NetCommand will send the Enter signal for
this function):
channel selection.
Learn the ENTER key for channel selection in
the NetCommand Enter (digits) learning posi-
tion. Use this learning position only if the original
remote control has separate keys for Enter in
menus and Enter for channel selection.
Cancel
—
CANCEL as the Cancel or Exit Function
1. Press MENU or GUIDE to display the menu or
guide.
“Learn” the Cancel or Exit function in the
NetCommand Cancel learning position
2. Press CANCEL and NetCommand will send
the Cancel or Exit signal.
The symbol “—” can serve as the separator
Press digit key(s) and press CANCEL.
(separator) between a digital channel’s main and sub-channel NetCommand will send the channel-separator
digits, e.g., digital channel 12-1 (main channel is
signal.
12, sub-channel is 1).
“Learn” the channel separator function in the
NetCommand – (separator) learning position.
The MORE Key Menu and NetCommand
Perform NetCommand setup for these device-specific
keys and then access their functions with the MORE key.
Device
Key
Device
Key
Menu
Top Menu
Input
Angle
SP/EP
Audio (DVD)
Subtitle
Repeat
List
On Demand
A
B
C
D
Bonus View
Setup
Surround
Night
Download from Www.Somanuals.com. All Manuals Search And Download.
50
5. NetCommand IR Control (837 Series)
Operating NetCommand-Controlled Devices, continued
NetCommand Specialized Device Keys
Refer to this chart when “learning” device keys. “Learn”
some, all, or none of the keys used for each device
type.
See page 48 for more on keys marked in the “Special
Operation Method” column.
See Special
Operation
Method Table
Key Name in
Function
Name on TV
Remote Control
Learning Screen
Power On
Guide
Power On or Power ON/OFF (toggle)
On-Screen Program Guide or DVD Disc Menus
Next Channel Higher
9
9
Channel +
Channel –
Next Channel Lower
Page Up
Page Dn
Page Up in Guides
Page Down in Guides
Up
Arrow up
Down
Left
Arrow down
Arrow left
Right
Enter
Arrow right
Enter or Select (menus)
9
9
Cancel
Play
Cancel or erase (menus)
Start playback
Stop
Stop playback
Forward
Rewind
Pause
Fast Forward
Rewind/Fast Reverse
Pause playback
Start Recording
Record
1, 2, 3, 4, 5, 6, 7, 8, 9, 0 Digits
1, 2, 3, 4, 5, 6, 7, 8, 9, 0
Enter (digits)
- (separator)
Use after entering digits to tune directly to a
channel by number
9
9
Add digital channel separator between main
channel number and sub-channel number
Last
Info
Last Channel Recall
On-screen status display or information display
May require two
keypresses
Power Off
Power Off
9
Download from Www.Somanuals.com. All Manuals Search And Download.
51
NetCommand IR Control of an A/V
Receiver
6
Several types of A/V receiver control can be set up
using the Inputs > AVR menu.
Controlling an A/V Receiver
after NetCommand Setup
•
•
Power and volume. See the next page.
Audio switching. For most equipment setups, see
“Case 1: Automatic A/V Receiver Switching to the
TV Audio Input” page 53.
Switching Audio to and from the A/V
Receiver
1. Press MORE and then (AUDIO).
2. Press to show the Speakers option.
3. Press to select either AV Receiver or TV.
9
•
Audio switching and surround sound. To set up
switching to a surround sound device, see “Case
2: Automatic A/V Receiver Switching to a Surround
Sound Device” page 54
•
Audio and video switching over HDMI. If your
A/V receiver has an HDMI output, it may be con-
venient to send audio and video to the TV over a
single HDMI cable through the A/V receiver. See
“Case 3: Automatic Audio and Video Switching via
HDMI,” page 54.
Controlling A/V Receiver Power
With Any Connection Type
1. Press MORE and then
9
(AUDIO).
2. Press to show the Speakers option.
3. Press to select AV Receiver.
4. Point the remote control at the TV (not the A/V
receiver) and press POWER to power the A/V
receiver on or off.
Note: To set up control of other device types, see
“Initial NetCommand Setup,” page 47.
With an HDMI Connection
1. Press ACTIVITY
.
2. Highlight the A/V receiver icon.
3. Press POWER
.
Controlling Other A/V Receiver Functions
With the A/V receiver powered on and selected, the
TV’s remote control operates the volume and mute
functions. Also, when you switch to a device in the
Activity menu, the A/V receiver automatically switches
to the correct audio input for the device.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
6. NetCommand Control of an A/V Receiver (837 Series)
Setting Up A/V Receiver Control
Power and Volume
Perform this setup to control the A/V receiver power
and volume with the TV’s remote control.
To perform this setup you need:
•
The remote controls for both the TV and the
A/V receiver.
•
An IR emitter cable available from Mitsubishi.
Before You Begin
Inputs > AVR screen. Perform
NetCommand IR “learning” for A/V
receiver power and volume keys.
1. Connect your A/V receiver to the TV and any addi-
tional devices. See “Setting Up TV Inputs,” page 10
and “TV Connections,” page 14.
2. Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 46.
3. When the Power text starts flashing, aim the A/V
receiver’s remote control at the TV and hold the
POWER or POWER ON key until a check mark appears
next to Power.
3. Set the TV’s remote control to TV mode using the
side button.
•
If the text stops flashing before the check mark
appears, repeat this step.
Setup to Control A/V Receiver Power and Volume
•
To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
1. Open the Inputs > AVR screen in one of two ways:
•
If using the New Device Found screen for the
A/V receiver, highlight NetCommand and press
ENTER to open the AVR screen.
4. Press the key on the TV’s remote control to highlight
other keys in the list. Repeat steps 2 and 3 for each addi-
tional function you wish to control through NetCommand.
•
If performing NetCommand setup at any time
after Auto Sensing:
5. If the A/V receiver has a separate POWER OFF key,
press on the TV’s remote to highlight Power Off.
Repeat steps 2 and 3 to “learn” the POWER OFF key.
If the device has no POWER OFF key, skip this step.
Press MENU, highlight Inputs, and highlight AVR
to open the AVR menu.
2. The first function highlighted in the AVR screen is
always Power. Aim the TV’s remote control at the
TV and press ENTER to begin learning for Power.
6. When finished “learning” the power and volume
keys, either
•
•
To watch TV, press BACK
To continue with NetCommand setup to control
.
switching of A/V receiver inputs, highlight
NEXT and press ENTER
.
IMPORTANT
To hear audio sent from the TV to the A/V receiver,
you must have:
•
•
•
•
•
Physically connected the TV to the A/V receiver
via the analog or digital audio output.
Assigned, if needed, the name AVR if using an
HDMI A/V receiver.
“
Learned” the IR codes for the A/V receiver
inputs.
Assigned the TV’s audio output to the correct
input in the NetCommand Inputs > AVR menu.
Selected the A/V receiver as the audio source.
Press MORE then 9 (AUDIO), then
to show
the Speakers option, then to select the A/V
Receiver.
Download from Www.Somanuals.com. All Manuals Search And Download.
6. NetCommand Control of an A/V Receiver (837 Series)
53
Setting Up A/V Receiver Control, continued
•
Analog Stereo Audio. Audio from sources with only
analog stereo output (such as a VCR) can be sent either
directly to the A/V receiver or through the TV first.
Automatic Audio or Audio/Video Switching
The following setups enable the A/V receiver to switch
automatically to the correct input when you select a
device in the TV’s Activity menu.
Mitsubishi recommends you send audio through the
TV as shown in the example. The TV converts analog
audio to digital format to send to a digital A/V receiver.
Three different connection arrangements are described
here. Review the descriptions to find the setup needed
for your equipment.
•
HDMI Digital Stereo Audio. Digital stereo audio
from an HDMI connection is available both in digital
and analog format from the TV’s analog and digital
audio output jacks.
To hear digital surround sound from a source device
you must use the setup described for Case 2
.
To set up control of an A/V receiver you need:
VCR with
Analog Audio Output
•
•
•
The remote controls for the TV and A/V receiver.
An IR emitter cable available from Mitsubishi.
Connecting cables
audio output from
TV (digital or analog)
IMPORTANT
DVD audio
input
TV audio input
All audio from what you are watching on the TV is
always available from both the TV’s AVR AUDIO
OUTPUT and DIGITAL AUDIO OUTPUT jacks.
TV audio
TV
out
A/V Receiver
To use the digital surround sound capabilities of
your A/V receiver however, you must connect the
audio output from your DVD player, satellite receiver,
or cable box directly to the A/V receiver.
Incoming Coaxial Cable
to TV’s ANT input
Important: To use this setup, you must connect the TV’s
audio output to the A/V receiver’s TV audio input jack.
Before You Begin
1. In the Inputs > AVR menu, press
to highlight
TV audio out as the A/V receiver input to control.
1. Connect your A/V devices to the TV and connect
your A/V receiver to the audio outputs on the TV
and the DVD player. Note the name of the device
connected to each A/V receiver input. See initial
setup, page 10, and “TV Connections,” page 14.
2. Press ENTER on the TV’s remote control.
3. While the text TV audio out is flashing, press and
hold the TV INPUT key on the A/V receiver’s remote
control.
2. Position NetCommand IR emitters as described in
4. When a check appears next to TV audio out,
“IR Emitter Placement,” page 46.
release the TV INPUT key.
3. Set the TV’s remote control to TV mode using the
•
If the text stops flashing before the check mark
appears, repeat this step.
side button.
•
To erase the IR code just “learned,” press
CANCEL while the name is highlighted.
4. Open the Inputs > AVR menu, highlight NEXT
and press ENTER to display the device-key-learning
menu.
5. Press MENU if finished or continue with Case 2 setup
for another audio source.
Case 1: Automatic A/V Receiver
Switching to the TV Audio Input
Most devices are set up to use the TV’s audio output like
the VCR in this example; analog audio from the device is
sent through the TV to the A/V receiver’s TV audio input.
Use this setup for:
•
Audio Available from TV only. Send audio from
the ANT input to the A/V receiver from the TV’s
analog or digital audio output.
Case 1: NetCommand setup for controlling A/V
receiver switching to the A/V receiver’s audio input from
Use this setup to make the A/V receiver switch to its
designated TV audio input when viewing programming
from the ANT input.
the TV The list displayed represents inputs in use. The
.
device names are those you assigned during Auto Input
Sensing or in the Inputs > Name menu..
Download from Www.Somanuals.com. All Manuals Search And Download.
54
6. NetCommand Control of an A/V Receiver (837 Series)
Setting Up A/V Receiver Control, continued
5. If finished, highlight EXIT and press ENTER or
continue to set up additional A/V receiver audio
sources.
Case 2: Automatic A/V Receiver Switching
to a Surround Sound Device
Note: Use this setup to send digital surround sound
from a device directly to your sound system.
Case 3: Automatic Audio and
Video Switching via HDMI
A device can send digital surround sound such as Dolby
Digital or DTS directly to the A/V receiver. The device might
be a DVD player, cable box, or satellite receiver, and could
have HDMI output. A DVD player is used in this example.
If your A/V receiver has an HDMI output, it may be
convenient to route video signals from multiple devices
over a single cable to the TV. Use this procedure to set
up NetCommand control of the A/V receiver’s audio
and video switching over a single HDMI cable. The
connected source devices can be analog, digital, or a
mixture or the two. When this setup is complete, you
can use the TV’s Activity menu to select a video device
connected to the A/V receiver.
Your setup may include additional devices with digital
surround sound connected directly to the A/V receiver.
These devices might be a DVD player plus a cable box
or satellite receiver.
%7%ꢀBVEJPꢀ
JOQVU
%7%ꢀ1MBZFSꢀ
XJUIꢀ
EJHJUBMꢀTVSSPVOEꢀTPVOE
%JHJUBMꢀ
4VSSPVOEꢀ
4PVOE
"ꢁ7ꢀ3FDFJWFS
A/V Receiver
WJEFP
57
HDMI
TV
Output
HDMI Cable
Case 2: A/V receiver audio from a device providing
surround sound directly to the A/V receiver
VCR
1. In the Inputs > AVR menu, press
to highlight
Blu-ray player
the name of the A/V receiver input to control. In this
DVD player
Cable box
example, it is the DVD input.
2. Press ENTER on the TV’s remote control.
More About Using an HDMI Connection
•
Audio from devices connected directly to the TV
can be heard from the TV speakers only. To send
audio to the A/V receiver from such devices, use
one of the optional audio connections shown in the
diagram on the opposite page. For example, use
an optional audio connection if you wish to use the
A/V receiver speakers to hear audio from:
-
-
The ANT input
A game or camcorder connected to the conve-
nience input (INPUT 3).
Case 2: NetCommand setup for
controlling A/V receiver switching
to the A/V receiver’s DVD input. The list contains
connected inputs with names assigned during Auto
Input Sensing.
•
In some circumstances, audio from a device con-
nected to the A/V receiver may not be passed over
the HDMI cable to the TV speakers. In these cases
you must use the A/V receiver speakers to hear
audio.
3. While the text DVD is flashing, press and hold the
DVD INPUT key on the A/V receiver’s remote control.
Before You Begin
4. When a check appears next to DVD, release the
To complete these steps you will need:
DVD INPUT key.
•
The remote controls for both the TV and the
A/V receiver.
•
If the text stops flashing before the check mark
appears, repeat this step.
•
•
An IR emitter cable available from Mitsubishi.
•
To erase the IR code just “learned,” press
CANCEL while the name is highlighted.
An HDMI-to-HDMI cable to connect the A/V
receiver to the TV and cables necessary to
connect devices to the A/V receiver.
Download from Www.Somanuals.com. All Manuals Search And Download.
6. NetCommand Control of an A/V Receiver (837 Series)
55
Setting Up A/V Receiver Control, continued
1. Connect your audio/video devices to the A/V
receiver. Note the name of the device connected
to each A/V receiver input. This information will be
needed later to set up NetCommand’s automatic
input switching.
6. Perform the procedure in “Case 2: Automatic A/V
Receiver Switching to a Surround Sound Device”
on the opposite page.
2. Connect the A/V receiver to the TV with an HDMI-to-
HDMI cable.
3. Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 46.
Setup to Control Automatic Audio
and Video Switching via HDMI
1. Power on the A/V receiver.
2. Set the TV’s remote control to TV mode using the
To set up A/V switching over HDMI, choose your
devices from a list. Unlike the device list described for
Case 2, this generic list contains more than just the
devices detected in your setup.
side button.
3. Power on the TV.
4. When the New Device Found screen displays, select
device name AVR if it is not recognized automatically.
5. Navigate to the Inputs > AVR menu or, from
within the New Device Found screen, highlight
NetCommand Control of a Device Con-
nected to an HDMI A/V Receiver
NetCommand and press ENTER
.
DVI/PC INPUT
ANT
Use this setup to have NetCommand control a device
sending audio and video through the A/V receiver to the
TV via HDMI.
L
TV main panel
AVR
AUDIO
OUTPUT
3D
HDMI
2
GLASSES
EMITTER
R
1
3
L
AVR
AUDIO
DIGITAL
AUDIO
O
R
L
R
AUDIO
Net
ut
OUTPUT
Any Connection
Type
HDMI
Cable
DIGITAL
AUDIO
OUTPUT
Source
Device
A/V
Receiver
Optional analog or
digital audio
TV
connection
The A/V receiver’s remote control key for the input must
have been “learned” previously using “Setup to Control
Automatic Audio and Video Switching via HDMI” on this
page.
1. Set up NetCommand control of A/V receiver audio/
video switching via HDMI as described on this
page.
A/V receiver
with HDMI
output
L
R
HDMI OUT
DIGITAL
AUDIO
2. Press BACK to close any open menus and return to
normal TV viewing.
VCR
3. Press ACTIVITY
.
High-definition
DVD player
4. Highlight the icon for the A/V receiver input you
wish to control.
DVD player
5. Press ENTER to switch the TV to the A/V receiver
Cable box
and the A/V receiver to the device.
6. Open the Inputs > Learn menu.
7. Perform NetCommand “learning” for the device by
following the steps in “Initial NetCommand Setup,”
page 47.
Multiple video inputs through a single HDMI cable. You can
connect multiple video devices to an A/V receiver that has
an HDMI output. The optional audio connection allows you
to hear, through the A/V receiver, devices connected to the
TV only, e.g., an antenna on the ANT input.
Download from Www.Somanuals.com. All Manuals Search And Download.
56
Appendices
Appendix A: Bypassing the Parental Lock . . . . . . . . . . . . . . 57
Appendix B: Programming the Remote Control . . . . . . . . . . . 59
Appendix C: HDMI Control of CEC Devices . . . . . . . . . . . . . . 66
Appendix D: TV Care . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Appendix E: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 72
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
57
Mitsubishi DLP Projection TV
Appendix A: Bypassing
the Parental Lock
C9 Series
737 Series
837 Series
Bypassing the Parental Lock
After you set the lock, you must use your pass code to:
•
•
•
•
View a locked program
View the locked TV
Cancel the lock
Enter the Lock menus
If you forget your pass code, you can view the locked
TV without entering your pass code. When prompted
for the pass code, press the number
9
and
(LAST)
keys on the TV remote control at the same time. This
process temporarily unlocks the TV.
When entering the Lock menu, you are prompted to
enter a pass code.
•
To change the pass code, press
9
and
(LAST)
at the same time. Either enter a new pass code to
open the Lock menu and make changes or press
BACK to close the menu.
•
•
If any of the locks are turned on and you exit the
menus when prompted for a new code, the old
code and all lock settings are retained.
If all locks are turned off and you exit the menus
when prompted for a new code, then the previous
code is erased.
IMPORTANT
When changing or deleting your pass code,
you must use the remote control included
with this TV. You cannot use a Mitsubishi
remote control from another component or a
“universal” remote.
IMPORTANT
Cut along the dotted line and file bypass
instructions in a safe place for future
reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
58
Appendices
This page intentionally left blank
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
59
Appendix B: Programming the Remote Control
This appendix explains programming the TV’s remote
control to operate other A/V devices. This is distinct
from NetCommand control.
VCRs and DVRs
•
•
•
•
•
•
CHANNEL UP/DN
POWER
SLEEP (from MORE menu)
•
•
•
•
•
•
(
(
(
RECORD
REVERSE
STOP
)
)
)
Functions Available for Other A/V Devices
(
(
(
FAST FORWARD
PAUSE
PLAY
)
GUIDE (DVR only)
MENU (DVR only)
0–9 Number Buttons
The TV’s remote control can be programmed to operate
other types and brands of A/V products. The functions
performed in each switch position vary depending on
the product. Not all functions work for all models. The
most common functions available are listed on this
page.
)
)
Mitsubishi VCRs are compatible with some additional keys.
Cable Boxes and Satellite Receivers
(not all functions for all models)
•
•
•
•
•
•
•
•
PAGE UP/DOWN
CANCEL
CHANNEL UP/DN
ENTER
GUIDE
POWER
The record/playback keys:
•
•
•
•
•
•
(
(
(
(
(
(
FAST FORWARD
PAUSE
PLAY
RECORD
REVERSE
STOP
)
)
)
)
)
ACTIVITY
TV modes
GUIDE
MENU
INFO
BACK
)
LAST (ENTER; for chan-
nels on some models)
•
0–9 Number Keys
A/V Receivers
•
•
•
•
•
MUTE
POWER
SLEEP (from MORE menu)
VOLUME
0–9 Number Buttons
•
Direct Input Selection
buttons: numbers
and LAST (on some
Mitsubishi models)
To use the remote after
programming, press the side
button to change the control
mode to match the device
type.
CD Players
(not all functions for all models)
•
•
•
•
SLEEP (from MORE menu)
•
•
•
(
(
REVERSE
STOP
)
(
(
(
FAST FORWARD
PAUSE
PLAY
)
The MORE Menus
The MORE key displays a menu showing additional key
functions available for a device type after programming
the remote control.
)
)
0–9 Number Buttons
)
DVD Players
(not all functions for all models)
•
CANCEL (on some
models)
CHANNEL UP/DN (for
track skip on some
models)
ENTER
MENU
•
•
•
•
•
•
•
(
(
(
(
(
(
FAST FORWARD
PAUSE
PLAY
RECORD
REVERSE
STOP
)
)
•
)
)
)
•
•
•
•
•
)
0-9 Number Keys
POWER
SLEEP (from MORE menu)
IMPORTANT
Some manufacturers may change their
products or they may use more than one
remote control system. The TV’s remote
control may be unable to operate your A/V
equipment in these cases.
Download from Www.Somanuals.com. All Manuals Search And Download.
60
Appendices
Appendix B: Programming the Remote Control, continued
Programming the Remote Control
Mode
Device Type
Code
1. Press the side button on the remote control to
change to the correct mode for the product you
want to control. Refer to the table below. Only
one of each device type can be controlled in each
mode.
CABLE/SAT
VCR
DVD
AUDIO
Mode
Affected Device
IMPORTANT
CABLE/SAT
Cable Box
DTV Receiver
Satellite Receiver
You may need to reprogram the remote control after
changing the batteries. Record the codes for each
mode in the space provided to make this faster.
VCR
VCR
DVR
DVD Player/Recorder
Code Verification
To determine the code programmed for any mode:
1. Set the mode to the one you wish to verify.
2. Press and hold POWER on the remote control for
several seconds until the mode indicator blinks twice
and goes off.
DVD
DVD Player/Recorder
DVR
VCR
AUDIO
A/V Receiver
Audio Amplifier
CD Player
3. Press keys
9
9
0
4. Press and count the blinks of the power key.
1
2. Press and hold POWER on the remote control for
several seconds until the mode indicator blinks
twice and goes off.
Write down the number of blinks as the first digit of
the code.
5. Repeat step 4 for the second, third, fourth, and fifth
3. Release the POWER key.
digits of the code.
4. Enter the first five-digit code listed for your equip-
ment.
•
The mode indicator blinks twice when you
start to enter the code and then once for each
additional keypress.
Audio Lock: Universal A/V Receiver
Control
With Audio Lock enabled, the remote control operates
volume and mute on the A/V receiver in all modes set by
the side button. Activate Audio Lock if you normally use
an A/V receiver with your TV and other A/V equipment.
•
•
The mode indicator blinks twice when you finish
entering a valid code.
If you need to start over or wish to exit pro-
gramming mode, temporarily change to a
different mode using the side button.
1. Program AUDIO mode for your A/V receiver as
described in “Programming the Remote Control” on
this page.
5. Point the remote control at the equipment and
press POWER. If the product has no power on/off
2. With the remote control in AUDIO mode, hold POWER
on the remote control for several seconds until the
mode indicator blinks twice and goes off.
function, press a different key, such as
(PLAY),
(
STOP), VOLUME UP, or MUTE.
•
•
If the equipment responds, the remote control
is properly programmed.
3. Press keys
9
9
3
ENTER
The mode indicator will blink twice to indicate Audio
Lock is active.
If the equipment does not respond, repeat
steps 2–4 with the next five-digit code listed for
your equipment.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
6. Once you have found the correct code, write it in
the space below for future reference.
1. Press and hold POWER for several seconds until the
mode indicator blinks twice and goes off.
2. Press keys
9
9
3
VOLUME UP.
The mode indicator will blink four times to indicate
Audio Lock has cleared.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
61
Appendix B: Programming the Remote Control, continued
Programming Codes
Audio Amplifiers
Cable Boxes
Paragon
Penney
CD Players
Parasound 40420
Penney
Philips
Pioneer
Proceed
Quasar
RadioShack 40420, 40180, 40000
RCA
Realistic
Adcom
41100, 40577
10525, 10008, 10000
10000
Altec Lansing 41742
40029
40626
41087
40420
40029
Bel Canto
Design
Bose
Carver
Cary Audio
Design
41583
Philips
Pioneer
11305
11877, 10877, 10533,
10144
40674
40892
41879
Pulsar
Quasar
Runco
10000
10000
10000
40420
40420, 40180, 40087,
40000
40435
40420
Samsung
Scientific
Atlanta
Sejin
10144
Classe
Flextronics
Halcro
Harman/
Kardon
JVC
41461
41879
41934
40892
11877, 10877, 10477,
10237, 10008, 10000
11602
Roksan
Rotel
Sansui
Sanyo
Sharp
Sherwood
Sony
40000
Sony
11006
40087, 40000
40180, 40037
41950, 40180
41364, 40490, 40185,
40100, 40000
Sprucer
Toshiba
US Elec-
tronics
Videoway
Zenith
10144
10000
10008
40331
Krell
41837
40892
41802, 41145
40892
41483
Left Coast
Lexicon
Marantz
Mark
10000
10899, 10525, 10000
Symphonic 40180
Tascam
TDK
40420
41208
40490, 40420, 40180
40029
40072
40087
41292, 40490, 40036
40000
Levinson
Parasound
Philips
Polk Audio
Victor
CD Players
Acoustic
Research
Akai
Burmester
California
Audio Labs
DKK
Fisher
Garrard
Hafler
Harman/
Kardon
Inkel
41934
40892
40892
40331
40354
40420
Teac
Technics
Victor
Wards
Yamaha
Yorx
40083
40420
40029
Yamaha
Cable Boxes
A-Mark
ABC
10144, 10008
10237, 10008
10237
40000
40000
40420
40173
41202, 40173, 40100,
40083
40180
A/V Receivers
ADC
Aiwa
40531
Acorn
41641, 41405, 41388,
41243, 40189, 40121
41390
41077
41609, 41074
41189
Action
Active
10237
10237
Alco
Americast 10899
AMC
Anam
Arcam
Audiotronic 41189
Audiovox
Bose
Amino
Archer
11822, 11602
10237
Integra
JVC
Kenwood
40101
Bell South 10899
41294, 40072
40626, 40190, 40037,
40029, 40000
41711, 41318
41317
41208
40038
40626, 40435, 40180,
40038, 40029
41703
Century
Cisco
Comcast
Digeo
10008
11982, 11877, 10877
11982
41390
41933, 41841, 41629,
41253, 41229, 40639
40189
KLH
Koss
LG
Magnavox
Marantz
12187
Director
GE
10476
10144
10476
Cairn
Capetronic 40531
Carver
General
Instrument
GoldStar
Hitachi
i3 Micro
Insight
41289, 41189, 40189,
40121
40014
10144
10008
11602
10476
Curtis
McIntosh
MCS
Memorex
MGA
Miro
Mitsubishi
Modulaire
Mathes
Daewoo
Denon
40029
40420, 40000
40083
41250
41360, 41306, 41142,
40121
40531
41801
Jerrold
Memorex
Motorola
Myrio
10476
10000
11376, 11254, 10476
11822, 11602
40000
Emerson
Fisher
Grundig
Harman/
Kardon
Hitachi
40098, 40083
40420, 40180, 40087,
40000
40420
41208
41327, 40101
40420, 40087, 40037,
40000
40189
Nova Vision 10008
41306, 41304, 41289,
40891, 40189, 40110
41801
42169, 41893, 41077,
41030
MTC
NAD
Onkyo
Optimus
Novaplex
Pace
10008
11877, 10877, 10237,
10008
Insignia
Panasonic 11982, 10144, 10008,
10000
Panasonic
40752, 40388, 40029
Download from Www.Somanuals.com. All Manuals Search And Download.
62
Appendices
Appendix B: Programming the Remote Control, continued
Programming Codes, continued
A/V Receivers
A/V Receivers
Satellite Receivers
Integra
41805, 41320, 41298,
Technics
Thorens
Toshiba
Venturer
Wards
41518, 41308
41189
41788, 41123, 40842
41390
40189, 40014
41815, 41476, 41376,
41375, 41331, 41276,
41176, 41023, 40176
41921
SKY
Sony
Thomson
Tivo
10099
11640, 11639, 10639
10566, 10392
11442, 11142
40842
JBL
JVC
41306, 40110
42331, 41643, 41495,
41374, 41282, 41058
41390
41570, 41569, 41313
41428, 41390
42197, 41293
Toshiba
11749, 10790, 10749
Yamaha
UltimateTV 11640, 11392
Kawasaki
Kenwood
KLH
Uniden
Zenith
10722
11856, 11810
LG
YBA
VCRs
A-Mark
Linn
Magnavox
40189
Zenith
41293
20278, 20046, 20037,
20000
41514, 41269, 41266,
41189, 40531, 40189
41289, 41269, 41189,
40891, 40189
41289
Satellite Receivers
Bell ExpressVu 11170, 10775
ABS
Accurian
Admiral
21972
20000
20479, 20209, 20060,
20048, 20047, 20039
Marantz
Chaparral
10216
Crossdigital 11109
McIntosh
DirecTV
11856, 11749, 11640,
Micromega 41189, 40189
Adventura 20037, 20000
11639, 11609, 11442,
11414, 11392, 11377,
11142, 11109, 10819,
10749, 10639, 10566,
10392, 10247, 10099
11775, 11505, 11170,
10775
Mitsubishi
41957, 41922, 41921,
Aiko
Aiwa
Akai
Alba
Alienware
Allegro
America
Action
American
High
20278
41920, 41393
41189
41313
41905, 41805, 41320,
41298, 40842
20124, 20037, 20000
20242, 20175
20278, 20209
21972
20039
20278
Myryad
Nakamichi
Onkyo
Dish
Network
System
Dishpro
Echostar
Optimus
41074, 41023, 40531,
40121, 40014
11775, 11505, 10775
11775, 11505, 11170,
10775
Panasonic
42967, 41764, 41763,
41633, 41548, 41518,
41509, 41316, 41308,
41288, 41275
20081, 20035
Amstrad
Astra
Audiovox
Avis
20000
20035
20278, 20038, 20037
20000
Expressvu 11775, 10775
Fortec Star 11821
Philips
41269, 41266, 41189,
40891, 40531, 40189
41935, 41384, 41123,
41023, 40630, 40531,
40150, 40014
Funai
GE
11377
10566
Pioneer
Bell &
Howell
Bell
20479, 20048, 20046,
20039, 20035, 20000
21944
GOI
11775, 10775
11250, 10819, 10749
10775
11775, 10775
11749, 11442, 11142,
10749
Hitachi
Houston
HTS
Hughes
Network
Systems
Humax
Innova
JVC
Polaroid
41508
ExpressVu
Broksonic 20479, 20209, 20184,
20121
Polk Audio 41289, 40189
Proscan 41254
RadioShack 41609
Calix
20037
20038, 20037
20035
20081, 20035
20278
RCA
41609, 41511, 41390,
Candle
Canon
Carver
CCE
11790, 11781
10099
11775, 11170, 10775
11414
41254, 41123, 41074,
41023, 40531
41609, 40121
40189
Realistic
Revox
Rio
LG
Cineral
Citizen
20278
Magnavox 10722
Mitsubishi 10749
41869
20479, 20278, 20209,
20037, 20035, 20000
20037
Samsung
Sansui
Sanyo
41500, 41304, 41295
41189, 40189
41801
Netsat
10099
Classic
Panasonic 10701, 10247
Colortyme 20278, 20060, 20045,
20035
Pansat
Philips
11807
Sherwood
Sherwood
Newcastle
42169, 41905, 41077
42169
11749, 11442, 11142,
10775, 10749, 10722,
10099
Colt
Craig
20000
20047, 20037
20000
20081, 20035, 20000
20278
20432, 20278, 20162,
20060, 20035, 20000
Sonic Blue 41869
Sony 41858, 41822, 41759,
Criterion
Crosley
Crown
Curtis
Mathes
Proscan
10566, 10392
RadioShack 10775, 10566
41758, 41658, 41622,
41558, 41441, 41382,
41258, 41131, 41058
RCA
11442, 11392, 11142,
10855, 10775, 10566,
10392, 10143
11609, 11442, 11377,
11276, 11142, 11109
Stereophonics 41023
CyberPower 21972
Daewoo 20278, 20046, 20045,
20037
Samsung
Sunfire
Teac
41313
41390, 41074
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
63
Appendix B: Programming the Remote Control, continued
Programming Codes, continued
VCRs
Daytron
Dell
Denon
DirecTV
Dish
Network
System
Dishpro
Dual
VCRs
HTS
VCRs
20278, 20037
21972
20081, 20042
20739
21944
20739, 20042
Nikkodo
Niveus
Media
Northgate 21972
Olympus
Onkyo
20278, 20037
21972
Hughes
Network
Systems
Humax
Hush
Hytek
iBUYPOWER 21972
Instant
Replay
Jensen
JVC
21944
20162, 20035
20222
21062, 21048, 20593,
20432, 20162, 20048,
20047, 20037, 20035,
20000
20479, 20278, 20209,
20184, 20121, 20000
20035
21988, 21797, 20739
21972
20047, 20000
Optimus
21944
20000
20035
Durabrand 20039, 20038
Dynatech
Echostar
Electrohome 20209, 20060, 20043,
20037, 20000
Electrophonic 20037
Emerald
Emerex
Emerson
20000
21944
20067
Orion
21944, 20067
20278, 20037
20067, 20046, 20038
20037, 20035
20000
20038, 20037
21972
20038, 20000
20081
20000
20278
20046
20067, 20042, 20037,
20000
KEC
Panama
Kenwood
Kodak
KTV
Panasonic 21062, 20616, 20614,
20225, 20162, 20035,
20000
20184, 20121
20032
21593, 20593, 20479,
20278, 20209, 20184,
20121, 20043, 20037,
20000
LG
Penney
20162, 20081, 20067,
20047, 20042, 20038,
20037, 20035, 20000
20042
20479, 20209, 20081,
20035, 20000
21181, 21081, 20739,
20618, 20616, 20209,
20162, 20081, 20048,
20045, 20035, 20000
20037
20162, 20081, 20067,
20042
Linksys
Lloyd’s
Loewe
Logik
Lumatron
Luxor
LXI
Pentax
Philco
Expressvu 21944
Fisher
20047, 20046, 20039,
20000
20035, 20033
20000
21593, 20593, 20278,
20037, 20000
20000
21972
20060, 20048, 20035,
20000
20060
20278, 20037, 20000
21593
Philips
Fuji
Fujitsu
Funai
Magnasonic 20593, 20278, 20037,
20000
Magnavox 21593, 20618, 20593,
20563, 20081, 20048,
20039, 20037, 20035,
20000
Marantz
Marta
Matsui
Matsushita 20162, 20081, 20035
Media
Center PC
MEI
Memorex
Pilot
Pioneer
Garrard
Gateway
GE
Polk Audio 20081
Portland
Presidian
Proscan
Protec
Pulsar
Quarter
Quartz
20278
21593
20060
20000
20278, 20039
20046
20047, 20046, 20035
20162, 20035
20081, 20038, 20035
20037
20209, 20037
Gemini
Genexxa
GFM
Go Video
GOI
21972
20614, 20432
21944
20278, 20039, 20038,
20037, 20035, 20000
GoldStar
20035
Quasar
20479, 20278, 20209,
20162, 20048, 20047,
20046, 20039, 20037,
20035, 20000
20037
20060, 20043
21972
21972
RadioShack 20162, 20048, 20047,
20046, 20037, 20035,
20000
Radix
Randex
RCA
Goodmans 20278, 20081, 20037,
20000
Gradiente
Granada
Grundig
Harley
Davidson
Harman/
Kardon
20000
20081, 20042
20081
20037
20037
Metz
MGA
Microsoft
Mind
Minolta
Mitsubishi 20443, 20242, 20214,
20173, 20075, 20067,
20880, 20060, 20048,
20045, 20042, 20035,
20000
20278, 20162, 20121,
20048, 20047, 20046,
20037, 20035, 20000
20616, 20614
20000
20081, 20075, 20038
20042
Realistic
Headquarter 20046
Hewlett
Packard
HI-Q
21972
20060, 20048, 20047,
20043, 20042, 20000
20048, 20035
20000
20000
20039, 20000
20067, 20038
20278, 20037
ReplayTV
Ricavision 21972
Runco
Salora
20047, 20035, 20000
20089, 20045, 20042,
20037, 20035, 20000
21972
Motorola
MTC
MTX
Multitech
NEC
Nikko
20039
20075
20739, 20432, 20060,
20045, 20038, 20000
20048, 20039
Hitachi
Samsung
Howard
Computers
HP
Sanky
21972
Download from Www.Somanuals.com. All Manuals Search And Download.
64
Appendices
Appendix B: Programming the Remote Control, continued
Programming Codes, continued
VCRs
Sansui
VCRs
Touch
Trix
DVD and Blu-ray Players
20479, 20209, 20067,
20000
20479, 20159, 20047,
20046, 20000
20184, 20121, 20045,
20043
20209, 20162, 20067,
20060, 20048, 20047,
20046, 20045, 20043,
20042, 20039, 20037,
20035, 20033, 20000
20848, 20048, 20047,
20032, 20000
21972
20037
20278, 20045
20045
20184, 20038
B & K
BBK
30662, 30655
31224
Ultra
Bel Canto
Design
31571
Sanyo
Scott
Sears
Vector
Vector
Research
Victor
Video Con- 20242, 20045
cepts
Videomagic 20037
Videosonic 20000
Viewsonic 21972
Blaupunkt 30717
Blue Parade 30571
20067
Blue Sky
Bose
Brandt
30699, 30695
32023, 31895
30651
Broksonic 30695
California
Audio Labs
Celestial
Centrex
Cinea
30490
Sharp
Villain
Voodoo
Wards
20000
21972
31020
31004, 30672
30831
Shintom
Siemens
Signature
20039, 20000
20037
20479, 20060, 20048,
20046, 20037, 20035,
20000
20479, 20081, 20060,
20048, 20047, 20046,
20045, 20043, 20042,
20038, 20037, 20035,
20033, 20000
CineVision 30869, 30833
Citizen
32116, 31587, 31277,
31003, 30695
30571
31351, 31177, 31165,
31107, 31086, 31077,
30852, 30778
30831
Clairtone
Coby
Singer
20037
Wharfedale 20593
White
Westinghouse 20000
World
XR-1000
Yamaha
Zenith
Sonic Blue 20616, 20614
Sonographe 20046
Sony
20479, 20278, 20209,
21972, 21032, 20636,
Craig
20479, 20209
20035, 20000
20038
21139, 20479, 20278,
20209, 20039, 20037,
20033, 20000
21972
20067, 20047, 20046,
20035, 20033, 20032,
20000
Creative
Curtis
30539, 30503
31087
Mathes
Soundmaster 20000
Stack 9
STS
SV2000
SVA
Sylvania
CyberHome 31537, 31502, 31129,
31117, 31024, 31023,
21972
20042
20000
20000
21593, 20593, 20081,
20043, 20035, 20000
30874, 30816
30705
ZT Group
Cytron
DVD and Blu-ray Players
Daewoo
31242, 31234, 31172,
31169, 30869, 30833,
30784, 30770, 30705
30770
30872
30770
32258, 30634, 30490
30778
31407
3D LAB
Accurian
Acoustic
Solutions
Adcom
Afreey
30539, 30503
31416, 30675
30730
Symphonic 21593, 20593, 20000
Systemax
Tagar
Systems
Tandy
Tashiko
Tatung
Dansai
Daytek
Decca
Denon
Denver
Desay
21972
21972
31094
30698
20000
20037
Aiwa
Akai
30641, 30533
31089, 30770, 30705,
30695
30717, 30672
30790
20081, 20067, 20048,
20000
20067, 20000
20162, 20037, 20035,
20000
20037, 20035, 20000
20479
20000
20060
20278
21944, 20739, 20636,
20618
20000
DigitalMax 31738
Alba
Alco
Digitrex
Disney
DiViDo
Dual
30672
31270, 30675
30705
Teac
Technics
Allegro
Amphion
Media
Works
AMW
Apex Digital 31061, 31056, 31020,
31004, 30797, 30796,
30794, 30755, 30717,
30672, 30533
30869
30872
31068, 30675
Teknika
Tevion
Thomas
Thomson
Tisonic
Tivo
Durabrand 31127, 31023
DVD2000 30521
Electrohome 32116, 31003
30872
Emerson
31268, 30675, 30591
Enterprise 30591
Entivo
Enzer
ESA
Firstline
Fisher
Funai
Gateway
GE
30539, 30503
30770
31268
30651
TMK
TNIX
Toshiba
Arrgo
31023
31168, 31407
20037
Aspire
Digital
Astar
Audiovox
Awa
21988, 21972, 21008,
20209, 20045, 20043,
20000
30670
31268, 30675
31158, 31077, 31073
30815, 30717, 30522
31489
31041, 30790, 30717
30730
Tosonic
Totevision 20037
20278
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
65
Appendix B: Programming the Remote Control, continued
Programming Codes, continued
DVD and Blu-ray Players
DVD and Blu-ray Players
DVD and Blu-ray Players
GFM
Go Video
31268, 30675
Myryad
NAD
Naiko
30894
30741
30770
Sharp
32250, 31256, 30752,
31730, 31304, 31158,
31144, 31099, 31075,
31044, 30869, 30833,
30783, 30744, 30741,
30717, 30715, 30573
30869, 30741
30675, 30630
31117
Sharper
Image
NEC
Nesa
30869, 30785
30717
Sherwood 31077, 31043, 30770,
30633
Sherwood 31077
Newcastle
NexxTech
Norcent
31402
31265, 31107, 31003,
30872
GoldStar
Goodmans 30790
Onkyo
Oppo
Optimus
Oritron
Palsonic
31769, 30627, 30503
31224, 30575
30571
30651
30852, 30672
GPX
30769, 30699
30651, 30490
30717
30705, 30539
30702, 30582
Shinsonic
Slim Art
SM Elec-
tronic
30839, 30533
30784
30730
Gradiente
Greenhill
Grundig
Harman/
Kardon
Sonic Blue 31099, 30869, 30783,
30715, 30573
Panasonic 31762, 31641, 30703,
30632, 30571, 30503,
30490
Hello Kitty 30831
Sony
31536, 31533, 31516,
31431, 31070, 31033,
30864, 30533
31074
30860, 30717
31268, 30675
Hitachi
Hiteker
Humax
iLo
Initial
Insignia
Integra
IRT
30664, 30573
30672
31588, 31500
31348
30717
32095, 31268, 30675
31769, 30627, 30571
30783
Philco
Philips
30675
32084, 32056, 31506,
31354, 31340, 31267,
31158, 30675, 30646,
30539, 30503
Sungale
SVA
Sylvania
Symphonic 31268, 30675
Phonotrend 30699
PianoDisc 31024
TAG
30894
McLaren
Tatung
Teac
Technics
Technika
JBL
JMB
30702
30695
Pioneer
31571, 31512, 31460,
30770
30632, 30631, 30571,
30525, 30142
31086, 31061, 31020
30790, 30717, 30571
30703, 30490
30770
JSI
JVC
31423
31550, 31275, 31164,
30867, 30623, 30558
31049
Polaroid
Polk Audio 30539
Technosonic 30730
Tevion 30651
Theta Digital 30571
jWin
Portland
Presidian
Proceed
Proscan
Prosonic
ProVision
Qwestar
30770
31738, 30675
30672
30522
30699
30778
30651
Kawasaki
Kenwood
KLH
30790
30534, 30490
31149, 31020, 30790,
30717
Thomson
Tivo
Toshiba
30522, 30511
31588, 31512, 31503
31769, 31608, 31588,
31515, 31510, 31503,
31154, 30695, 30573,
30539, 30503
30800
Kloss
Koss
30533
31423, 31061, 30769,
30651
Radionette 30741
RadioShack 30571
Lasonic
Lecson
Lenoxx
LG
30798, 30627
31533
31127
30869, 30741, 30591
31738, 31656, 31440,
31416, 31158, 31058
30741, 30511
30783
Tredex
Unimax
United
RCA
31769, 30822, 30790,
30770
30730
30717, 30571, 30522
30571
30752
Realistic
Reoc
Universum 30591
Urban Con- 30539, 30503
cepts
LiteOn
Revoy
Rio
Rotel
30699
30869
31178, 30623
31004
Loewe
Logix
US Logic
V
Venturer
Vizio
Wesder
Xbox
Yamaha
30839
31226, 31064
30790
31226, 31064
30699
32083, 30522
30646, 30545, 30539,
30497, 30490
Magnasonic 30675, 30651
Magnavox 31506, 31354, 31268,
30675, 30646, 30539,
30503
Rowa
Saba
Sampo
Samsung
30651
30752, 30698
31075, 31044, 30820,
30744, 30573, 30490,
30199
Marantz
McIntosh
Medion
Memorex
Microsoft
Minato
30675, 30539, 30503
31533, 31273
30651
31270, 30831, 30695
32083, 30522
30752
Sansui
Sanyo
30695
30873, 30695, 30675,
30670
Yamakawa 30872
Zenith
30869, 30741, 30591,
30503
30784
31265
Schneider 30783
Schwaiger 30752
Zeus
Zoece
Mintek
30839, 30717
Mitsubishi 31521, 30521
Mustek 30730
Sensory
Science
31158
Download from Www.Somanuals.com. All Manuals Search And Download.
66
Appendices
Appendix C: HDMI Control of CEC Devices
Many new HDMI devices have a feature called Con-
sumer Electronics Control (CEC) or HDMI Control.
HDMI Control allows one device, such as the TV, to
control other devices, such as an A/V receiver or disc
player. Use of CEC is optional.
4. If prompted for a name,
highlight the name you want
to assign the device.
Each manufacturer chooses which CEC functions to
support so it is difficult to predict which devices and
features are compatible with Mitsubishi’s HDMI Control.
You may find that CEC functions for a specific device are
limited.
5. Highlight On.
To use HDMI Control, you must enable it in both
the TV and the device.
7. Highlight EXIT and press ENTER to close the New
•
In the TV. Enable HDMI control from the New
Device Found screen or from the Inputs > HDMI
Control menu.
Device Found screen.
Note: At any time after completing Auto Input Sens-
ing, you can set the TV’s HDMI control on or off
in the Inputs > HDMI Control menu.
•
I
n the Device. Most devices with HDMI CEC com-
patibility let you turn it on or off in the device menus,
where it is typically listed as “HDMI Control.”
If the New Device Found Screen
Displays No HDMI Control Option
If the New Device Found screen shows no option for
HDMI Control, one of these conditions applies:
Enabling HDMI Control of CEC Devices
To ensure proper detection
•
Power on HDMI devices before connecting them to
the TV.
•
HDMI Control is turned off in the menus of the
new device
•
Connect and set up HDMI devices one at a time.
1. Power on the device and allow it to complete the
Action:
power-on sequence (boot up). Stop any playback.
a. Highlight EXIT and press ENTER to close the
New Device Found screen.
b. Display the device’s setup menus and enable
the device’s CEC capabilities.
2. Connect the device to one of the TV’s HDMI inputs.
3. When the TV detects the connection, the New
Device Found screen will appear.
c. Wait for the TV’s New Device Found screen
to appear again.
Note: See “If the New Device Found Screen Displays
No HDMI Control Option” on this page if there is
no HDMI Control option.
d. If the New Device Found screen still has no
HDMI Control option, power off the device.
Power on the device and wait for the New
Device Found screen to display with the
HDMI Control option.
•
The device does not have CEC compatibility
Action:
-
Control the device with its own remote
control or program the TV’s remote control to
operate the device.
New Device Found screen with HDMI Control option.
This screen displays only if the device’s HDMI Control is
-
837 Series. Use the TV’s NetCommand IR
control (page 45).
enabled
.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
67
HDMI Control of an HDMI A/V
Receiver and Connected Devices
DIGITAL
AUDIO
OUTPUT
Note: Connect the A/V receiver to the TV before con-
AVR
AUDIO
OUTPUT
HDMI
VIDEO: 480i/480p/720p/1080i/1080p
AUDIO: PCM STEREO
DVI/PC
AUD
Optional
R
PC: VGA, W-VGA, SVGA, W-SVGA,
XGA, W-XGA, SXGA, 720p/ 1080p
necting any other device to the A/V receiver.
NetCommand
ut External
/
oller Input
digital audio
connection
HDMI
2
ANT
ANT
2
1
/
/
AUX
MAIN
1
3
R
/ I
1. Enable HDMI Control for the A/V receiver as
described in “Enabling HDMI Control of CEC
Devices” on the opposite page.
R
AUDIO
L
DIGITAL
AUDIO
OUTPUT
TV back panel
2. Power on the HDMI device you wish to connect to
the A/V receiver (such as a disc player, cable box,
or satellite receiver). Allow the device to complete
the power-on sequence (boot up). Stop playback if
the device starts playing.
A/V receiver with
HDMI output
DIGITAL
AUDIO
OUTPUT
HDMI OUT
3. Connect the device to the A/V receiver with an
HDMI cable.
VCR
4. Select the device’s HDMI input on the A/V receiv-
High-definition
DVD player
er’s front panel controls or remote control.
DVD player
5. When the TV detects the connection, the New
Device Found screen will appear.
Cable box
Note: If the TV is unable to detect the device, either
the device’s CEC capability is not enabled or
the device is not CEC compatible. Enable
HDMI control through the device’s menus
before continuing. You may need to temporar-
ily connect the device directly to the TV to view
device menus.
Connecting HDMI devices. The optional digital audio
connection allows you to hear audio through the A/V
receiver from devices connected to the TV only.
6. Highlight On.
7. Highlight EXIT and press ENTER to close the New
Device Found screen.
8. Optional: Connect the TV’s DIGITAL AUDIO
OUTPUT to an input on the A/V receiver. Use this
additional connection if:
•
You want the ability to switch between the A/V
receiver speakers and the TV speakers.
You want to use the A/V receiver to listen to
devices connected to the TV only, e.g., an
antenna input or camcorder.
•
9. 837 Series. If desired, perform NetCommand IR
Learning to supplement CEC functions. You must
first connect and place IR emitters for the devices.
See page 45.
Download from Www.Somanuals.com. All Manuals Search And Download.
68
Appendices
Resolving CEC Conflicts
Using HDMI Control
Because each manufacturer selects which CEC func-
tions to support, some devices can conflict with other
devices. If control conflicts arise, you can:
As an example of using HDMI Control, press PLAY on
the device itself to:
•
•
Power on the TV
Switch to the device (no need to display the
Activity menu)
•
Turn off TV control of an individual CEC-enabled
device (see below).
•
Begin play of the device
•
Turn off CEC in the setup menu of one of the
devices.
Direct Keys
Turning Off the TV’s HDMI Control of a CEC Device
Test your equipment with the TV’s remote control to
find additional supported commands. See the table
below for commands that may be available, depending
on the individual device.
1. Press MENU on the TV remote control.
2. Highlight Inputs > HDMI Control and press ENTER
to open the menu.
CEC-enabled VCR, DVD, and DVR functions that
may be available:
3. Move to the device name and press
to select
Off to turn off the TV’s ability to control the device.
Record/
Playback
Menu
Navigation
4. Press MENU to clear the menu.
Channel Tuning
Other
CHANNEL UP/DN
GUIDE
MENU
ENTER
Digits 0–9
,
CANCEL
CANCEL
(to cancel)
ENTER
If you have a CEC-enabled A/V receiver, CEC-enabled
devices connected to the A/V receiver with an HDMI
cable may also be controllable. They can be selected
from the TV’s Activity menu.
Inputs > HDMI Control menu
Removing an HDMI Device
1. Power off the device.
2. Disconnect the HDMI cable.
CEC-enabled A/V receiver functions that may be
available:
•
Try the VOLUME UP/DOWN MUTE, and menu-navigation
,
3. Press MENU on the TV remote control to enter the
keys.
TV main menu.
•
To open the A/V receiver menu, follow these steps:
4. Highlight Inputs > Name and press ENTER to open
1. While watching TV, press MORE then (AUDIO).
9
the menu.
2. Press until the Speakers option displays.
3. Press to select AVR as the source.
4. Press MORE and then 1 (MENU) to display the
menu.
5. Select Delete from the HDMI input names.
6. Press MENU to clear the menus.
The MORE Menu
Press MORE on the TV’s remote control to see a menu
of additional supported functions for the current
CEC-enabled device. To issue a command, press the
number key indicated in the menu.
Inputs > Name menu with Delete selected for HDMI-3.
MORE key: Sample menu for
a CEC-enabled DVD player
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
69
Appendix D: TV Care
Lamp-Cartridge Replacement and Cleaning
CAUTION: If the television is on, press POWER to turn it off. Unplug the television and
allow it to cool for at least one hour before attempting to replace the lamp cartridge.
Lamp
The light source for this television is a
lamp, which is part of a lamp cartridge
assembly. The life of the lamp can
vary, based on the lamp itself, the air
temperature around the TV while it is
operating, the selected lamp mode, and
your viewing patterns. Warmer air or
poor ventilation shorten the lamp life,
as does use of the Bright lamp mode
and turning the television on and off
CAUTION
BURN DANGER! HOT SURFACES INSIDE!
Touch lamp cartridge handle only. Do not touch lamp or lamp car-
tridge housing. Keep lamp cartridge horizontal during removal. Do
not tilt as glass may come out and cause injury. Replace lamp car-
tridge only with the same part number 915B403001.
frequently. Mitsubishi warrants the lamp for one (1) year from the date of
original TV purchase at retail.
WARNING
THE ACCESS PANEL IS
To Order a New Lamp
PROVIDED WITH AN INTERLOCK
TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET
RADIATION. DO NOT DEFEAT
ITS PURPOSE OR ATTEMPT TO
SERVICE WITHOUT REMOVING
PANEL COMPLETELY.
To Receive a Replacement Lamp Under Warranty
•
•
Call (800) 553-7278. Please have model number, serial number,
and TV purchase date available.
Important: All lamps replaced under warranty must be returned to
Mitsubishi where they will be inspected for defect verification.
To Purchase a Replacement Lamp After Warranty
Lamp Part Number 915B403001
Lamp-Substitution Alert
MDEA recommends that you use only genuine Replacement Lamp Assemblies purchased directly from Mitsubishi or a
Mitsubishi Authorized Dealer or Mitsubishi Authorized Service Center. MDEA advises that replacement lamps obtained
separately from the Lamp Cartridge and/or Lamp Assemblies obtained from unauthorized sellers may be incorrect for
your television, may not fit or perform properly and may even damage your television. MDEA can not be responsible
for the performance, reliability or safety of any replacement lamps that are obtained from unauthorized sources.
WARNING
•
Do not remove the lamp cartridge immediately after turning off the television. You may get burned because the
lamp is very hot. Allow the television to cool for at least one hour before replacing the lamp cartridge.
•
•
•
Do not remove the lamp cartridge except when replacing it. Careless treatment can result in injury or fire.
Do not touch the lamp glass element. It may be very hot and break, causing injuries or burns.
Be sure not to insert any metal or flammable object into the lamp cartridge opening, as it may cause fire or electrical
shock. If a foreign object is inserted into the opening, unplug the AC cord of the TV and contact your dealer for service.
•
•
Install the lamp cartridge securely. Failure to do so may cause a fire.
Do not touch the lamp glass elements. Oils from your fingers may cause premature lamp failure.
THE LAMP INSIDE THIS PRODUCT CONTAINS MERCURY AND MUST BE RECYCLED OR
DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. For disposal or recy-
cling information, please contact your local authorities or the Electronic Industries Alliance at
Hg
= MERCURY
Download from Www.Somanuals.com. All Manuals Search And Download.
70
Appendices
Appendix D: TV Care, continued
Lamp-Cartridge Replacement
Removing the Old Lamp Cartridge
1. Turn off TV power and unplug the TV. Allow the
lamp to cool for at least one hour before proceed-
ing.
Figure 1
2. After the lamp has cooled, remove the cover of the
Figure 2
lamp compartment, located on the back of the TV.
Refer to figures 1 and 2. Use a #2 (medium) Phillips
screwdriver to loosen the screw securing the cover.
Keep the screw and cover for re-installation
3. With a medium Phillips screwdriver, loosen the two
screws securing the lamp cartridge until they dis-
engage from the mating threads. These are captive
screws and cannot be separated from the lamp
cartridge.
4. Fully open the bag supplied with the replacement
Figure 3
lamp and set the opened bag aside.
5. Gently grasp the handle of the lamp cartridge and
Use only replacement lamp part number
915B403001.
pull the old cartridge straight out. See figure 3.
CAUTION: Do not tilt or rotate the cartridge, as
small glass fragments may fall out.
6. Without tilting or putting down the lamp cartridge,
insert it into the opened bag. Close the bag while
being careful not to let any glass particles fall out.
Lamp-Cartridge Filter Cleaning
If the TV shuts off after displaying the message “TV
will shut down in a few seconds. Please check if the
air flow is blocked” and/or the STATUS LED is yellow, the
air filter may need cleaning. The air filter is part of the
lamp cartridge. Use the following procedure to clean
the filter.
1. Remove the lamp cartridge from the TV as
described under “Removing the Old Lamp Car-
tridge.” Do not tilt or rotate the cartridge. Do not
touch the glass parts of the lamp cartridge.
Installing the New Lamp Cartridge
1. Do not touch the glass parts of the new lamp car-
tridge. Insert the new cartridge into the TV in the
same orientation as the old cartridge. Push on the
cartridge housing until it is fully seated.
2. Gently tighten the screws with the screwdriver.
AVOID OVERTIGHTENING!
3. Replace the plastic cover and retaining screws.
4. WASH YOUR HANDS THOROUGHLY, AS THIS
2. Holding the lamp cartridge horizontal (do not tilt or
rotate), use a soft dry brush or vacuum cleaner to
remove any dust that may be present on the mesh
filter. Do not use liquids. See figure 4.
LAMP CONTAINS MERCURY.
Disposal of the Old Lamp Cartridge
Lamp under warranty: All lamps replaced under war-
ranty must be returned to Mitsubishi. Use the return
shipping label provided and send to Mitsubishi Digital
Electronics, America, 625 Braselton Parkway, Suite 200,
Braselton, GA 30517.
3. Reinstall the lamp cartridge as described under
“Installing the New Lamp Cartridge.”
IMPORTANT: Lamps found to be without defect will
be returned and charged back to the sender.
Figure 4
Lamp no longer under warranty: Contact your
local authorities or the Electronic Industries Alliance at
Do not dispose of the old lamp with common trash.
Keep lamp
cartridge horizontal
and remove dust
from the mesh filter
using a vacuum
cleaner or soft dry
brush.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
71
Appendix D: TV Care, continued
Cleaning Recommendations
Care of the Remote Control
Normally, light dusting with a dry, non-scratching duster
will keep your TV clean. If cleaning beyond this is
needed, please use the following guidelines:
Remote Control Tips
•
•
•
•
For longer life, use alkaline batteries.
Do not mix old and new batteries.
Be within 20 feet of the equipment.
First, turn off the TV and unplug the power cord from
the power outlet.
Occasionally clean dust build-up from the air-intake
grilles on the back and sides of the TV. Clean using a
vacuum cleaner with a brush attachment.
Do not press two or more keys at the same time
unless instructed to do so.
•
•
•
•
Do not allow the unit to get wet or become heated.
Keep the unit out of direct sunlight.
Top and Sides of the TV
•
Gently wipe down your TV with a soft, non-abrasive
cloth such as cotton flannel, microfiber, or a clean
cloth diaper, lightly moistened with water. Dry with
a second dry, soft, non-abrasive cloth.
Avoid dropping on hard surfaces.
Do not use harsh chemicals to clean. Use only a
soft, lightly moistened cloth.
Resetting the Remote Control
•
For oily dirt, add a few drops of mild liquid deter-
gent, such as dishwashing detergent, to the water
used to moisten the cloth. Rinse with a second
cloth moistened only with water. Dry with a third
dry, soft, non-abrasive cloth.
If TV mode is selected and the TV does not respond
properly, reset the remote control.
1. Press and hold POWER for several seconds until the
mode indicator blinks twice and goes off.
Screen
2. Release the POWER key.
•
•
•
Follow the instructions for the top and sides, wiping
gently in an up and down motion.
Clean the entire screen evenly, not just sections of
the screen.
Do not allow liquid to drip down the screen, as
some liquid may enter the TV through the gap
between the screen and screen frame.
You may purchase Mitsubishi Screen Cleaner, part
number CLEANER-VSS, by calling (800) 553-7278.
3. Press keys
0
0
9
3
5
and the mode indicator will
blink twice when you finish entering the code.
When entering the code, pause for a moment
between each key press to ensure it is recognized.
Low-Battery Indicator
If you press a key and the mode indicator blinks five
times, replace the remote control’s batteries.
•
General Cleaning Precautions
•
•
•
DO NOT allow liquid to enter the TV through the
ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as
these can scratch the surfaces.
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
•
•
DO NOT spray liquids or cleaners directly on the
TV’s surfaces.
DO NOT scrub or rub the TV harshly. Wipe it gently.
Download from Www.Somanuals.com. All Manuals Search And Download.
72
Appendices
Appendix E: Troubleshooting
channel (a channel from the ANT input, a cable box, or
satellite receiver), first check other channels from the
same input before changing settings. If most other
channels from the same input seem correct, there is
likely a problem with the broadcast rather than with the
TV. Use care in this case, as changes you make to fix
problems on individual channels also affect all other
channels on the same input.
TV Reset Comparison Guide
You can resolve many common TV problems using
the reset functions described in the following table.
See also the troubleshooting suggestions later in this
appendix.
IMPORTANT
Before you change sound or picture settings: If
picture or sound settings seem wrong for a broadcast
Reset Name
Format
When to Use
How to Use
Resulting Action
When the picture
shape seems
incorrect, use
MORE > 0 (FORMAT) to
change the shape of
the picture.
Press the MORE key and then repeat- The last-used format for a signal
edly press
0
(FORMAT) to cycle
type is memorized for each input.
The next time the same input and
the same signal type is viewed,
the last-used format will be
recalled.
through the available aspect ratios.
™
™
PerfectColor
Reset
or
When the color
intensities seem out
of balance, use the
1. While viewing the input to
All PerfectColor/PerfecTint
sliders are reset to the original
center position. The PefectColor/
PerfecTint settings for other
inputs remain unchanged.
be reset, press MENU and
+
go to Adjust > Picture >
PerfectColor / PerfectColor/PerfecTint
PerfectColor.
™
PerfecTint
reset to reset the color
balances to the original
factory settings.
Both PerfectColor and
PerfecTint are reset at
the same time.
2. Press ENTER to display the
Reset (837
Series)
PerfectColor adjustment screen.
3. Press CANCEL to reset the colors.
(for the single
input currently
being watched)
A/V Memory
Reset
(for the single
input currently
being watched)
When audio and/
or video settings for
a single input seem
incorrect, use A/V
Memory Reset to
return the input to
the original factory
settings.
1. While viewing the input to reset, All Audio and Video settings
press MENU and go to Adjust >
for the individual input are
reset except for the Listen To,
Language, audio Balance,
Closed Caption, and Advanced
Picture settings.
Reset.
2. Press ENTER to highlight the
Reset icon.
3. Press ENTER again to reset.
Customer Support
Service and Customer Support
•
To order replacement or additional remote con-
trols or lamp cartridges, visit our website at www.
mitsuparts.com or call (800) 553-7278.
Service
If you are unable to correct a problem with your TV,
consult your Mitsubishi dealer or Mitsubishi Con-
sumer Relations at (800) 332-2119.
•
For questions:
Call Consumer Relations at 800-332-2119.
E-mail: [email protected]
•
DO NOT adjust any controls other than those
described in this Owner’s Guide.
•
DO NOT remove the protective back cover of
your TV.
Important
All lamps replaced under warranty must be returned
to Mitsubishi where they will be inspected for defect
verification.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
73
Appendix E: Troubleshooting, continued
Reset Name
When to Use
How to Use
Resulting Action
A/V Reset
(for all inputs)
To reset audio and
video adjustments for
all inputs to the original VOLUME DOWN at the same time.
factory settings.
While viewing the TV, press the
control-panel buttons ACTIVITY and
All Audio and Video settings are
returned to the original factory
settings, including Listen To,
Language, audio Balance,
Closed Captions, Format and
Advanced Picture settings.
Channel
To erase and
1. While viewing the TV, press
All previously memorized chan-
Memorization
re-memorize channels
on the ANT input.
MENU to display the main menu. nels for the antenna input are
2. Navigate to the Initial> Channel erased and a new set of memo-
menu.
3. Press ENTER.
4. Highlight the reception mode,
e.g. Ant Air.
rized channels is created. To add
or delete individual channels, see
Initial > Channel > Edit menu
instructions on page 39.
5. Highlight Scan.
6. Press ENTER to start channel
memorization.
Lock Menu
Pass Code
To change your Lock
menu pass code
See the cutout page from Appendix A, Allows establishment of a new
page 57.
code.
Control-Panel
Lock Release
To re-enable the
Press and hold the ACTIVITY button
on the control panel for over eight
seconds. This works even if the TV
is powered off.
Allows the control panel to be
unlocked if the remote control is
misplaced.
control-panel buttons
after activation of the
Control-Panel Lock
Auto Input
Sensing for
HDMI
When connecting an
HDMI device does
not trigger Auto Input
Sensing.
1. Disconnect the HDMI device.
2. Delete the HDMI input in the
Inputs > Name menu (see page
40).
The New Device Found screen
will display.
3. Power on and connect the new
device.
System Reset
If the TV does not turn Press and hold the POWER button on The TV will turn off and the green
on or off, does not
respond to the remote
control or control-
panel buttons, or has
audio but no video.
the control panel for ten seconds.
LED will flash quickly for about
one minute. When the green
LED stops flashing, you may turn
on the TV. The changes you
made most recently, before using
SYSTEM RESET, may be lost.
TV Reset
To reset all consumer- 1. While viewing the TV, press
The TV will start the initialization
process. The TV will then turn
off and the front green LED will
start flashing. When the LED
stops flashing, you can turn on
the TV again. All memory and
settings outlined in this Owner’s
Guide will need to be set again.
IMPORTANT:
Use this reset
only if all other
resets have been defaults.
unsuccessful.
accessible settings
and all memories to
the original factory
MENU to display the TV main
menu.
2. With the main menu displayed,
press number keys 1 2 3 to
display the Reset menu.
3. READ THE ON-SCREEN
WARNING AND INSTRUC-
TIONS.
CAUTION: All owner-
performed setups and
adjustments will be
erased.
•
If you do not wish to use this
reset, press BACK or MENU to
back out.
•
If you do wish to use the
reset, press ENTER to erase
all memories and settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
74
Appendices
Appendix E: Troubleshooting, continued
General TV Operation
Symptom
Remarks
1. A fan is running even while the TV is powered The room is too warm. When the TV is off, internal components
off.
continue to draw power and must be cooled by the fan.
2. The fan gets louder after the TV is shut off.
Normal operation. The fan speeds up to cool the lamp quickly
after the TV has been shut off.
3. The TV remote control does not work.
•
•
•
•
•
Check that the batteries are fresh and installed correctly.
Check that the control mode on the remote is set to TV.
Be no more than 20 feet from the TV when using the remote control.
Program the remote control to operate the TV or other device.
Reset the remote control.
4. When I try to use the remote control, the
Replace the batteries.
POWER key blinks five times.
5. TV does not respond to the remote control or
to control-panel buttons and TV will not power
on or off.
•
•
Unplug the AC power cord for 10 seconds.
Press and hold the POWER button on the control panel to
perform system reset.
6. When a device is selected from the Activity
menu, the screen is blue or black (no signal
source).
•
•
Make sure the selected device is turned on.
Begin play of the device.
7. You have forgotten your Lock menu pass code. See “Bypassing the Parental Lock”, Appendix A.
8. Rating restrictions are not working.
Open the Lock > Parental Lock menu and:
•
•
Verify that the ratings locks are active.
Check the Lock Time/Unlock Time to check if rating restric-
tions are disabled.
•
Rating restrictions apply only to content on the ANT input.
9. On-screen displays appear each time you
Normal TV operation.
change a function.
10. A warning message appeared on screen
stating, “TV will shut down in a few seconds.
Please check if the air flow is blocked.”
•
•
Internal TV temperature has exceeded proper levels. Cool
the room.
The TV has overheated. Clear blocked air vents and ensure
at least four inches of clearance on all sides of the TV.
Clean the air filter on the lamp cartridge.
•
I have turned on CEC for my HDMI devices but
control is erratic and I wish to disable it.
•
First turn off the TV’s HDMI control for the specific device. Open
the Inputs > HDMI Control menu, select the device, select Off.
Disable CEC on the device itself. See the device’s instructions.
If the problem persists, do the following:
11.
•
•
1. Disconnect the device from the TV.
2. Reconnect the device to the TV and Auto Input Sensing will
recognize the device with CEC disabled.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
75
Appendix E: Troubleshooting, continued
TV Channels
Symptom
Remarks
1. The TV takes several seconds to respond to
•
•
It is normal for digital channels to take longer to tune in.
Press ENTER after entering a channel number to avoid
delays.
channel changes.
•
•
Use a 4-digit number for an over-the-air digital channel.
Use a 6-digit number for digital cable channels if your cable
service is able to recognize 6-digit channel numbers.
2. You cannot access a channel.
•
•
•
Use number keys instead of CHANNEL Up/Down.
Be sure the channel you want to view is in memory.
Check that the TV is switched to the correct device or
antenna for that channel by pressing the ACTIVITY key.
Make sure the Lock > Parent menu lock is set to Off.
If you cannot tune to a virtual digital channel even though the
TV has already memorized digital channels, tune to the physi-
cal channel number used by the broadcaster. The virtual
channel will then be automatically added to memory.
You may be trying to tune to an analog channel that is no
longer broadcasting.
•
•
•
3. When ChannelView list is displayed, informa-
•
•
Press INFO to update the display for the highlighted channel.
Program information is displayed only for the currently tuned
channel.
tion appears incomplete
•
•
Available information is sent from the broadcaster or cable
provider. No other data is available.
Make sure the TV clock is set correctly.
TV Power On/Off
Symptom
Remarks
1. TV takes an excessively long time to power
When powered on, the TV needs time to boot up, just as a com-
puter does. Also, the TV’s lamp requires a few moments to heat
up to full brightness.
on.
2. You cannot program the TV to turn on auto-
•
•
The TV may be locked.
The clock may not be set.
matically (Timer function)
3. TV turned itself off and the light on the front
•
Momentary power fluctuation caused the TV to turn off to
prevent damage. Wait for the green light to stop flashing
and turn the TV on again.
panel started to blink.
•
If the TV does not stay on, press the POWER button on the
control panel for at least eight seconds to perform System
Reset. If this happens frequently, obtain an AC line power
conditioner/surge protector.
•
An unusual digital signal may have been received, triggering a
protection circuit. Wait for the light to stop flashing and turn TV
on.
4. TV will not power off.
Press the POWER button on the control panel for ten seconds
to perform System Reset.
Download from Www.Somanuals.com. All Manuals Search And Download.
76
Appendices
Appendix E: Troubleshooting, continued
Picture
Symptom
Remarks
1. Picture does not look like a high-definition
Not all signals are high-definition signals. To receive high-defini-
tion programming from your cable or satellite provider, you must
subscribe to the provider’s high-definition service. Some over-
the-air broadcasts are in high-definition and can be received with
a high-quality antenna suited to your location.
picture.
2. TV has sound but no picture.
•
•
Check that all video inputs are plugged in firmly.
Press and hold the POWER button on the control panel for
ten seconds to perform System Reset.
3. Picture has become dimmer.
•
•
•
The lamp is nearing the end of its life. Order a new lamp.
Adjust picture brightness and contrast to maximum levels.
Change Lamp Energy from Standard to Bright.
4. There is a large black or gray rectangle on
The TV’s analog closed captioning has been set to “text” mode
in the Captions menu. Turn off because there is no text informa-
tion being broadcast.
the screen.
5. You cannot view a picture when playing a
Check your VCR’s owner’s guide for further troubleshooting.
VHS tape.
6. VCR or DVD player’s on-screen menus jitter Stop playback. Possible cause: Many VCRs and DVD players
up and down.
provide on-screen menus at only half-resolution that may
appear to jitter up and down.
7. When viewing a stopped VCR, white lines
•
•
•
Turn off video mute for the VCR.
Begin playing the tape.
Change the VCR input from Line 1 to the VCR antenna input.
are rolling on the screen.
8. A color program appears as a black and
white image, or the colors are dim, or the
screen is black.
The PerfectColor color balance has been incorrectly set. Reset
the PerfectColor balance.
9. Picture from an HDMI input is noisy (poor
Upgrade a Category 1 (unmarked) HDMI cable to a Category 2
high-speed HDMI cable.
quality).
10. The image from a computer appears dis-
•
Normal TV operation. The TV does not correct distortion in
the picture from a computer because the correction process
may cut off the edges of the image.
torted when viewed on the TV.
•
The aspect ratio may be wrong for the image. Press MORE
and then 0 (FORMAT) to change.
Sound
Symptom
Remarks
1. There is no sound even when the
•
•
Check if the MUTE key is on.
The TV’s “Listen to:” setting may be set to SAP (analog program
from the ANT input).
volume is turned up.
•
Check that the Speakers option is set to TV to hear sound from the
TV speakers. Sound may be being sent to one of the audio outputs
for an A/V receiver or headphones.
•
•
If using an A/V receiver, check that the Speakers option is set to AV
Receiver to hear sound from the A/V receiver speakers.
Press and hold the POWER button on the control panel for 10
seconds to perform System Reset.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
77
Appendix E: Troubleshooting, continued
Sound
Symptom
Remarks
The TV’s “Listen to:” setting may be set to SAP (analog program from
the ANT input)
2. The sound does not match the screen
picture.
.
3. The sound from my A/V receiver does
not match the screen picture (I should
hear the correct audio from my A/V
receiver).
•
Check that DIGITAL AUDIO OUTPUT and/or AVR AUDIO
OUTPUT on TV’s main panel is connected to the A/V receiver.
Without this connection, devices connected only to the TV (and
not the A/V receiver) can be heard only from the TV speakers.
Note that this includes the ANT input, a device (such as a
camcorder) connected to the convenience panel, and any other
device sending audio to the TV only.
•
•
If using a NetCommand-controlled A/V receiver, NetCommand
may be selecting the wrong A/V receiver audio input. Check the
A/V receiver’s NetCommand setup in the Inputs > AVR menu.
If playing MP3 files from a USB device, check that the TV’s audio
output is connected to the A/V receiver.
4. Cannot select an audio-only device; it
Plug an unused video plug into the Y/VIDEO jack to activate Auto
Input Sensing and make the audio device selectable in the Activity
menu.
does not appear in the Activity menu.
NetCommand IR Control (NetCommand-equipped models only)
Symptom
Remarks
1. Cannot see the menu from the A/V Receiver.
•
A/V Receiver Set Up for Audio-Only Switching
The A/V Receiver is not connected to any video input of the
TV. To check the A/V Receiver menu, temporarily plug into
an unused input of the TV, such as Input 3. Exit the New
Device Found screen and select Input 3 from the Activity
menu. Press MENU on the A/V receiver’s remote control.
•
•
A/V Receiver Set Up for Audio and Video Switching over
HDMI
Use the MENU key on the A/V receiver’s remote control.
A/V Receiver with HDMI Control
Switch the remote control to AUDIO mode. Press the
MORE key and then 1 (Menu).
2. NetCommand unable to learn specific device
•
•
•
•
A/V Device does not use IR format for remote control
signal. ITT and RF formats cannot be learned.
Room lighting may affect the signal. Have the remotes very
close (6 inches or less) to the TV during Learning.
If learning a Mitsubishi remote control, make sure mode is
not set to TV.
Some, but not all, device key functions can be learned by
NetCommand. For example, POWER and PLAY may be
learned, but other functions may not.
keys.
•
The signal from the remote control may not be strong
enough. Insert fresh batteries and try Learning again.
Download from Www.Somanuals.com. All Manuals Search And Download.
78
Appendices
Appendix E: Troubleshooting, continued
NetCommand IR Control (NetCommand-equipped models only)
Symptom
Remarks
3. The A/V receiver is the selected audio source • A/V Receiver Set Up for Audio-Only Switching
but there is no sound.
-
-
Check to see if the A/V Receiver power is turned on.
With A/V receiver power turned on, redisplay the Activ-
ity menu and press ENTER to allow NetCommand to
correctly select the A/V Receiver input.
-
Incorrect setup in the Inputs > AVR menu. Check the
device connection assigned in the AVR menu.
•
A/V Receiver Set Up for Audio and Video Switching over HDMI
-
-
Check to see if the A/V Receiver power is turned on.
If the device is connected only to the TV (e.g., on ANT
or a front panel input), verify that the TV’s AUDIO
OUTPUT is connected to the A/V receiver.
-
The A/V receiver is not switching properly because
you have not learned the IR codes for the A/V receiver
inputs to which your devices are connected.
4. There is no sound from the A/V receiver
NetCommand A/V receiver setup for the DVD player or digital
surround sound device or other device is not switching prop-
for my DVD player or other surround sound
device even though I learned the IR code for erly. See the owner’s guide and perform A/V receiver setup for
the A/V receiver’s DVD input or other input.
(A/V Receiver Set Up for Audio-Only Switch-
ing)
a digital surround sound device.
5. There is no sound or picture from the A/V
receiver for my DVD player or other device
connected to the A/V receiver; the A/V
receiver should be sending video to the TV
over an HDMI cable.
NetCommand A/V receiver setup is not switching audio and
video inputs properly. See the owner’s guide.
(
A/V Receiver Set Up for Audio and Video
Switching over HDMI)
6. I’ve selected my DVD player or other sur-
round sound device in combination with the
TV speakers but hear no sound from the TV
speakers.
•
A/V Receiver Set Up for Audio-Only Switching
If you have only an audio connection from the device to the
A/V receiver, a physical audio connection from the device
to the TV is also required.
-
Connect the left and right audio output from the device
to the appropriate TV audio input. Now you can hear
audio from the device through either the TV speakers or
the A/V receiver.
-
To switch audio sources, press MORE 9 (Audio), press
to show the Speakers option, then press to
select AV Receiver or TV.
•
A/V Receiver Set Up for Audio and Video Switching over HDMI
With your DVD player connected to the A/V receiver, only
video is passed from the A/V receiver to the TV because of
copy-protection restrictions on the HDMI signal
7. I “learned” the RECORD key for my VCR/DVR Check that the VCR or DVR is receiving a signal directly from
but when I pressed the RECORD key, the
your cable box or satellite receiver.
VCR/DVR did not record anything.
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademark and License Information
79
Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE.
®
®
Digital Light Processing and DLP are registered trademarks of Texas Instruments.
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
HDMI™ the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas
G. Lane, all rights reserved.
x.v.Color and the x.v.Color logo are trademarks of Sony Corporation.
ChannelView™, DeepField™ Imager, Easy Connect™, NetCommand®, PerfectColor™, PerfecTint™, Plush 1080p®
5G, SharpEdge™, Smooth120Hz™ are trademarks of Mitsubishi Digital Electronics America, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
80
Trademark and License Information
Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By
utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws
and treaties. The Software is licensed, not sold.
1.
only with the Mitsubishi television model that included this owner’s guide and owned by you.
2. RIGHTS AND LIMITATIONS.
LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that
Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material
in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more
than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.
3.
VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with any
violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other violation
of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This license
is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply with any
provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs,
animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned
by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the Software
is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and
treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the Software is
recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MDEA.
5.
EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States. You agree that you will not
export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq, Libya,
North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software
back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development,
or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in
U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S.
federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY
APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA. IN
NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR
OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES
MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT NEITHER MDEA’S
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE
ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. MDEA’s
liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money
paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL. This License Agreement will be governed by the laws of the State of California.
WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects
or other reproductive harm.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
81
Mitsubishi DLP Projection Television Limited Warranty
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this
television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects
arising from improper workmanship and/or material:
a. Parts. The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a
period of thirty (30) days from the date of the original purchase at retail. The lamp and all other parts (except any soft-
ware incorporated into this television) are warranted for a period of one (1) year from the date of the original purchase
at retail. We will repair or replace, at our option, any defective part without charge for the part. Parts used for replace-
ment may be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replace-
ment are warranted for the remainder of the original warranty period.
b. Embedded Software. MDEA warrants that all software incorporated into this television set (the “Embedded
Software”) will perform in accordance with the functional description of Embedded Software in all material respects,
but MDEA does not warrant that the Embedded Software is error-free. The limited warranty contained in this section
shall continue for a period of one (1) year from the date of the original purchase at retail. If, after prompt notice within
the warranty period, MDEA determines that the Embedded Software has failed to perform in accordance with such
functional description in all material respects and if such failure is not due to accident, misuse, modification or misap-
plication of the Embedded Software, then MDEA shall modify or replace the nonconforming Embedded Software at
no charge to you, which at MDEA’s sole discretion may be fulfilled by means of modification or replacement software
contained on a replacement memory card for Customer installation. The foregoing shall be MDEA’s sole obligation
to you under this limited warranty. All rights under this limited warranty on the Embedded Software also subject to
your acceptance of and compliance with the terms of the Software License Agreement applicable to this television,
and this limited warranty on the Embedded Software shall be null and void if the Embedded Software is modified or
changed in any manner except as specifically authorized by MDEA.
c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticu-
lar screen if it proves defective. For certain items that are designed to be replaced by the consumer, including (but
not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other
parts, we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for
one (1) year from the original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within
the applicable warranty time period.
e. This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the
image using small dots, or picture elements (pixels). Your DLP Projection TV is manufactured to a high level of perfor-
mance and quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technol-
ogy, sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MDEA warrants
only that the percentage of properly functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and
correct customer control adjustment. If the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your
MITSUBISHI dealer, by writing at the address provided below, calling MDEA at the 800-332-2119, or by using the
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your
television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center.
If not, you must either deliver your television to an authorized service location at your own expense, or pay for any
travel and/or transportation costs the service center may charge to and from your home. Actual service labor will be
provided without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service.
Present your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE
Download from Www.Somanuals.com. All Manuals Search And Download.
82
Warranty
OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However,
please return the Owner Registration Card so that we can contact you should a question of safety arise which could
affect you.
d. To obtain a replacement lamp, order the lamp directly from the MDEA Parts Department at (800) 553-7278.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where
such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other
than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to
carry out any maintenance as described in the Owner’s Guide including air vent cleaning or any product damaged
by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered,
defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage
caused by acts of God or other factors beyond the reasonable control of MDEA, such as power surge damage
caused by electrical system or lightning. This limited warranty also excludes service calls where no defect in the
product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or signal
unless caused by a defect in the product that is covered under this limited warranty, all costs, expenses or any other
damages arising from product installation, or set-ups, any adjustments of user controls (including contrast, bright-
ness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection
with any external audio receiver, antenna, cable or satellite systems, or service of products purchased or serviced
outside the U.S.A. Please consult the operating instructions contained in the Owner’s Guide furnished with the
product for information regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY
LIMITED TO A TERM OF ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of inciden-
tal, special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the
state where the television was purchased and the laws of such state will govern.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
83
Closed Captions 37
Color Adjustments 34
Reset Color 34, 72
Computer
and Display Formats 27
Connecting 26
Contrast 35
I
Index
INFO Key
ChannelView 22
A
USB Menu 28
Accent Lighting 33
IR Emitter Placement 46
IR NetCommand Output (jack) 16
Activity Menu 21
Automatic Generation 41
Change Input Name 40
Customizing 40
NetCommand-Controlled Switch-
ing of A/V Receiver Inputs 48
Removing a Disconnected HDMI
Device 40
L
Control Panel 9
Control Panel Lock 9, 44
Lamp Cartridge Replacement 69
Lamp Mode 39
D
Language
Date. See Clock
Changing the Menu Language
38
in Digital Programs 36
Default Settings, Returning to 72
DIGITAL AUDIO OUT 16
Dolby Digital 16, 54
DVD Player
and TV’s Remote Control 59
Connecting 17, 18
DVI Device, Connecting 18
Anamorphic Picture Format 24
Antenna Input (ANT) 15, 16
Signal Strength for Digital Chan-
nels 23
Audio Lock (A/V receiver control) 60
Audio Output Jacks 15, 16
Auto Input Sensing 11
Auto-Off (Sleep Timer) 21
Auto-On (Timer) 38
SAP (Second Audio Program) 36
Learn 40. See also NetCommand IR
Control
Letter Box Image Display 24
Level Sound 36
Listen To 36
Listings 22
Lock TV
F
Fan Noise 4
Film Mode 33
A/V Receiver
Bypassing the Lock 57
Lock by Ratings 43
Lock by Time 44
Lock Control Panel 44
Preset V-Chip Blocking 42
Filter, Air (on lamp cartridge) 70
Font (digital closed captions) 37
FORMAT (aspect ratio, MORE menu)
24
Freeze Picture (PAUSE key) 8
Front Panel
and Speakers Option 36
and TV’s Remote Control 59
Audio Lock 60
Connecting 16, 20
Controlling Sound Volume 22
Disconnecting Analog 22
NetCommand IR Control 51, 52
Controlling a Device Connected
to the A/V Receiver 31, 55
Video and Audio Switching via
HDMI 55
M
Blue Glow Accent Lighting 33
Controls 9
Memorizing Channels 10, 39
Add Single Channel to Memory
39
G
Game
MP3 Player (audio-only connection)
15
3D Video 25
Mute
B
Game Picture Mode 35
HDMI Cables for Games 16
GUIDE Key
Closed Captions 37
MUTE Key 8
Video Mute 33
Batteries 7
Blue Glow 33
Bright (Lamp Mode) 39
Brightness (picture adjustment) 35
ChannelView 22
HDMI Control 68
NetCommand Control 48, 50
N
Name (Inputs > Name menu) 40
NetCommand IR Control
About 45
C
Cable Box
H
and TV’s Remote Control 59
Connecting 17, 18, 19
Captions Menu 37
CEC (Consumer Electronics Control)
31, 66
A/V Receiver 22, 67, 77
Troubleshooting 74
Channels
HD (High-Definition) Signal) 24
HDMI
A/V Receiver Control 52
Initial Setup for Most Devices 47
Operating 48
Changing Out an HDMI Device
and Auto Input Sensing 11
Connecting an HDMI Device 17
A/V Receiver with HDMI 20
HDMI Cable Categories 16
HDMI Control of CEC Devices 66
HDMI Jack 16
Troubleshooting 77
P
Parental Menu 43
Pass Code
antennaweb.org 39
Physical/Virtual Channel Num-
bers 39
Resetting 57
Setting 42
Removing an HDMI Device from
the Activity Menu 40
Headphones
PAUSE Key 8
PerfectColor 34
PerfectTint 34
Photo Viewing 29
Scan (memorize) 10, 39
Troubleshooting 75
ChannelView™ Channel Listings 22
Cleaning 71
Jack 16
Speakers Option 36
Clock, Set Date and Time 38
Download from Www.Somanuals.com. All Manuals Search And Download.
84
Index
Picture
System Reset 9, 73
Picture+ Adjustments 34
Picture Menu Adjustments 35
Picture Quality and Film Mode
33
T
Test Picture 33
3D GLASSES EMITTER Jack 16
3D Video 25, 34
Time. See Clock
Timer (auto-on) 38
Time Zone. See Clock
Troubleshooting 72
Troubleshooting 76
Power On/Off 9, 12
Troubleshooting 75
R
Ratings (TV and Movie) 43
Remote Control
U
USB Menu 29
Batteries 7
Keys and Functions 8
Programming Codes (reference
chart) 61
Programming Instructions 60
Reset 71
V
V-Chip Ratings
Definitions 43
In Status Display 23
VCR
Reset
Connecting 19
A/V Memory Reset (for the cur-
rent input) 72
A/V Reset (for all inputs) 73
HDMI Auto Input Sensing 11
Pass Code 57
PerfectColor/PerfecTint 72
Remote Control 71
Remote Control Audio Lock 60
System Reset 9
Troubleshooting 76
Video from a Digital Camera 30
Video Game. See Game
Video Mute 33
Viewing Device. See Activity Menu
X
x.v.Color 16, 17, 35
TV Reset Comparison Guide 72
RS-232C 16
S
Safety Instructions 5
SAP (second audio program) 36
Satellite Receiver
and the Remote Control 59
Connecting 17, 18
Scan (memorize channels) 39
ScreenSaver 33
SD (Standard-Definition Signal) 24
Service and Support 72
Signal Definitions 24
Signal Strength Indicator 23
Sleep Timer 21
Sound
Controlling A/V Receiver Volume
(NetCommand) 52
Audio Lock 60
Level Sound 36
Sound Mode (audio effects) 36
Speakers Option 36
Standard-Definition Signal 24
Standard Lamp Mode 39
Stand Part Number 4
Status Display 23
Stereo System. See A/V Receiver
Surround Sound 53, 54
Simulated Surround Sound 36
TV Audio Outputs 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Website:
E-mail:
For questions, call Consumer Relations at
800-332-2119
To order replacement or additional
remote controls or lamp cartridges,
or call
800-553-7278
SYSTEM RESET
If the TV does not respond to the remote control,
control-panel buttons, or will not power on/off, press
and hold the POWER button on the control panel for
ten seconds.
The green LED will flash quickly for about one
minute. When the green LED stops flashing, you may
turn on the TV. Settings changes you made most
recently, before using SYSTEM RESET, may be lost.
V41_V41+_V41C_IB_20090325
© 2009 Mitsubishi Digital Electronics America, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|