Introduction
Mac OS X
En
Configuring the WT-4 for Upload to a
Computer (Ad-hoc Mode)
This document provides basic instructions on configuring the WT-4 wireless transmitter and a Mac OS
X (10.5.2) computer for transmission over an ad-hoc (peer-to-peer) network consisting solely of the
computer and WT-4.
Wireless
WT-4
Computer
Introduction
This section describes a simple wireless network consisting solely of the WT-4 and an computer, with
no connections to other networks or devices. Follow the steps below to use the WT-4 in this type of
network.
1: Get Ready............................................................................... pg. 2
2: Assign the Computer an IP Address ........................................ pg. 3
3: Configure the Network ........................................................... pg. 4
4: Copy the Network Profile to the Camera................................. pg. 7
5: Connect to the Computer...................................................... pg. 12
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
1
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Assign the Computer an IP Address
2: Assign the Computer an IP Address
Choose an address for the computer. The following IP address is intended as an example only.
•IP address: 192.168.1.3
•Subnet mask: 255.255.255.0
2 - 1
Open System Preferences and click Network.
2 - 2
Select AirPort. Click Advanced….
2 - 3
Select Manually from the Configure IPv4 menu
and enter an IP address and sub-net mask. Click
OK to return to the previous dialog and then click
Apply. This completes the process of assigning
an IP address to the computer.
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
3
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Configure the Network
3: Configure the Network
3 - 1
Open System Preferences and click Network.
3 - 2
Click the action button and select Set Service
Order.
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
4
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Configure the Network
3 - 3
Move AirPort to the top of the services list and click OK.
3 - 4
After selecting AirPort and confirming that the
service is active and that Show AirPort status
in menu bar is checked, click Apply. If AirPort is
off, click Turn AirPort On.
3 - 5
Click the AirPort status icon in the menu bar and
select Create Network....
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
5
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Configure the Network
3 - 6
After choosing a network name and channel and
adjusting encryption and password options as
described below, click OK.
• Name: Enter a name of up to 32 characters. The network in this example uses the identifier WT-4.
• Channel: Choose a channel.
• Require Password: Select this option to enable WEP encryption.
• Password: If WEP encryption is enabled, enter a security key. The length of the key depends on the option
selected for Security:
- 40-bit (more compatible): Enter a five-character ASCII or ten-digit hexadecimal key.
- 128-bit: Enter a 13-character ASCII or 26-digit hexadecimal key.
ASCII keys may contain letters, punctuation, and the numbers 0–9, hexadecimal keys the numbers 0–9 and
the letters a, b, c, d, e, and f.
• Security: Choose the length of the WEP key.
3 - 7
Open the System Preferences > Network panel
and confirm that the Network Name is the same
as that specified in 3 - 6. Network setup is now
complete.
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
6
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Copy the Network Profile to the Camera
4: Copy the Network Profile to the Camera
Use the WT-4 setup utility to copy the network profile to the camera. Before proceeding, make sure
that MTP/PTP is selected for the USB option in the camera setup menu.
4 - 1
After starting the computer, use the supplied USB cable to connect the camera and turn the camera on.
4 - 2
Click the WT-4 Setup Utility icon in the Dock.
4 - 3
The dialog shown below will be displayed; click
Next.
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
7
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Copy the Network Profile to the Camera
4 - 4
Select Add/Edit profiles and click Next.
4 - 5
Select Add new profile and click Next.
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
8
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Copy the Network Profile to the Camera
4 - 6
Enter the following information and click Next:
• Profile name: Enter a name of up to 16
characters (in this example, PC1).
• Profile type: Choose Computer.
• Interface type: Choose Wireless & Ethernet
for networks that include wireless, or Ethernet
only for Ethernet-only networks.
4 - 7
Enter the following information and click Next.
• Network name (SSID): WT-4
• Communication mode: Ad hoc
• Channel: 1
• Authentication: None (open networks only)
• Encryption: WEP64
• Encryption key: abc12
• Key Index: 1
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
9
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Copy the Network Profile to the Camera
4 - 8
Enter the following information and click Next.
• IP address: 192.168.1.4
• Subnet mask: 255.255.255.0
• Default gateway: Remove the check from this
option.
• DNS Server: Remove the check from this
option.
A
Choosing an IP Address
Be sure that the address for the WT-4 is different from the addresses used for the computer and access
point. The addresses for the access point, computer, and WT-4 must however belong to the same
class. In this example, we will use 192.168.1.2 for the access point, 192.168.1.3 for the computer, and
192.168.1.4 for the WT-4.
4 - 9
Confirm that settings are correct and click Next.
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
10
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Copy the Network Profile to the Camera
4 - 10
Select Finish wizard and click Next.
4 - 11
Turn the camera off and disconnect the USB cable. The network profile has now been copied to the camera.
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
11
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
5: Connect to the Computer
5: Connect to the Computer
In this step, you will establish a wireless connection between the WT-4 and the computer. Before
connecting the WT-4, select MTP/PTP for the USB option in the camera setup menu and confirm that
the host computer is running and the user is logged in.
5 - 1
Insert a memory card in the camera, connect the WT-4, and turn the camera on.
5 - 2
Choose an option for the Wireless transmitter >
Mode option in the camera setup menu.
5 - 3
A list of available connection profiles will be
displayed. Highlight the desired profile and
press J.
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
12
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
5: Connect to the Computer
5 - 4
Return to the wireless transmitter menu and turn
theWT-4 on.The profile name will be highlighted
in green when a connection is established.
This completes the process of connecting to the
computer.
A Third-Party Security Software
Third-party security software with firewall support may block the ftp server port, preventing access
to the computer. This can be avoided by setting the software to allow protocols send and receive
access to TCP ports 15740 and UDP ports 5353. For more information, see the documentation for the
software or firewall.
Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)
13
Mac OS X (10.5.2)
Download from Www.Somanuals.com. All Manuals Search And Download.
|