Nighthawk Carbon Monoxide Alarm KN COEG 3 User Manual

By KIDDE Sa fe t y

AC P ow ered w ith Ba ttery Ba ck up

Carbon Monoxide and

Explosive Gas Alarm

See pages

User ’s Guid e

4-1 and 4-2 for

“What to do When the

Alarm Sounds”

SINGLE STATION

CARBON MONOXIDE ALARM

Nighthaw k CO and Gas Alarm w ith

NIGHTHA

Digital Display, Peak Level Mem ory

and 9V Battery Backup

Model: KN-COEG-3

Explosive

Gas

Carbon

onoxide

Alarm

RESIDENTIAL

GAS DETECTOR

For questions concerning your Carbon Monoxide and Explosive

Gas Alarm, please call our Consumer Hotline at 1-800-880-6788.

Please have the follow ing information

ready w hen calling:

CO and Gas Alarm Model number (located on back of alarm):

CO and Gas Alarm Assembly number (located on back of alarm):

Date of Manufacture (located on the back of the alarm):

Date of Purchase:

Where Purchased:

Includes 9V Battery

810-1571 REV. C

03/01

Download from Www.Somanuals.com. All Manuals Search And Download.

Ab o u t t h is Us e r ’s Gu id e

In t ro d u ct io n

This Nighthawk carbon monoxide (CO) alarm is an important part of

your family’s home safety plan. As a new owner of a CO and Gas

alarm, there are some basic facts you should know for your protec-

tion and convenience.

Notice we call this booklet a “User’s Guide” and not an “Owner’s

Manual.” This is because our intention is you use this guide just

as you will be using your Nighthawk CO and Gas alarm. Keep

the guide in a handy location and refer to it when you have ques-

tions about your CO and Gas alarm, its functions and features.

Carbon monoxide (CO) is invisible, odorless, tasteless and non-irri-

tating–completely undetectable to your five senses. That’s why it’s so

important to your safety that you have a carbon monoxide and

explosive Gas alarm.

P a rt One

Your Nighthaw k Carbon Monoxide and Explosive Gas

Alarm, covers the unique features of your Nighthawk carbon

monoxide and explosive Gas alarm, how and where to install it,

as well as information on testing and maintaining your unit.

Natural Gas is typically supplied through a main utility line con-

nected to your home. If you do not live in a rural area you are like-

ly to be a user of natural Gas. It is the dominant energy used for

home heating with about 55 percent of American homes using Gas.

Natural Gas is a fossil fuel comprised almost entirely of Methane.

Methane is much lighter than air and will rise rapidly in air. If you are

a user of natural Gas, we recommend you mount your Nighthawk

unit 12 inches away from the ceiling (using retractable cord feature)

to ensure the earliest opportunity to detect a leak.

P a rt Tw o

Carbon Monoxide and Gas contains valuable information

about carbon monoxide (CO) and gas. From discovering the

most common sources of CO in your home to recognizing the

symptoms of CO poisoning, this section provides tips and infor-

mation that could help protect your family.

Propane is typically supplied to homes via delivery truck in liquid

form and stored near the home in propane tanks. Propane is used by

homes in rural areas that do not have natural Gas service. Since

propane is the most commonly used liquefied petroleum Gas (LPG),

“propane” and LP-Gas are often used synonymously. Unlike natural

Gas, propane is much heavier than air and will collect at lower lev-

els. If you are a user of propane, we recommend you mount your

Nighthawk near the floor (using the direct plug-in feature) to ensure

the earliest opportunity to detect a leak.

P a rt Three

What You Should Know Before the Alarm Sounds, pro-

vides a common sense approach to understanding the difference

between low level CO readings, high levels and emergency situ-

ations. This section also describes the effects of exposure to CO

levels over time and when your Nighthawk CO and Gas unit will

alarm.

Both Propane and Natural Gas are colorless and odorless. For safety

reasons, an ordorant (Mercaptan) is added so that any leak can be

detected by smell. The common detection threshold for smelling the

Gases is around 20% of the lower explosion limit (LEL). This can

vary greatly depending on the individuals sense of smell and how

long they have been exposed to it. The LEL of each of these gases

defines the bottom range of flammability for the Gas. Your

Nighthawk is calibrated to alarm before 25% of the LEL of either Gas

detected. Therefore, it is possible that you may smell Gas before

the alarm is activated.

P a rt Four

What to do When the Unit Alarms, gives you step-by step

information on how to respond to the different alarm situations.

Also covered is whom to call for help if you think you have CO

or Gas in your home.

P a rt Five

Technical Information, covers the technical specifications of

your Nighthawk CO and Gas alarm.

If you are not sure which Gas your home uses, contact your

utility company.

P a rt Six

Frequently Asked Questions, contains the most commonly

asked questions about our alarms. Part six was written by

KIDDE Safety customer service representatives who handle thou-

sands of calls per month, year-round. This section provides you

with answers and tips that will most likely answer any questions

you might have after reading this user’s guide.

Please take the time to read this guide from cover to cover, to famil-

iarize yourself with the facts about carbon monoxide, natural Gas and

propane. Know how your new unit works, and what to do if it

alarms. Then, find a handy place to keep the guide so it will be read-

ily available in the future when you have a question. You might want

to write down KIDDE Safety’s toll-free customer service number and

keep it with your other important phone numbers for the same rea-

son.

Thank you for making Nighthawk a part of your complete home

safety program. With proper installation and use, your new

Nighthawk CO and Gas alarm should provide you with years of

dependable service.

Download from Www.Somanuals.com. All Manuals Search And Download.

Qu ick Se t -Up Gu id e

We urge you to read this entire m anual in the sequence it is presented.

But, if you only read one part of this guide initially, read this page!

Listed below are seven easy steps for setting up your Nighthawk CO and Gas alarm. Please read the entire guide for complete

information.

Se t t in g u p yo u r CO a n d Ga s a la r m fo r fir s t t im e o p e r a t io n :

Step 1

Step 5

Determine the best location for your CO and Gas alarm(s).

Refer to page 1-3 for complete information.

At power up, you will see a flashing red dot and three eights

in the digital display indicating the alarm is warming

up. After approximately 20 seconds the unit will start sam-

pling for CO. After approximately 2 minutes the unit will start

sampling for gas. During this period a number will appear on

the digital display. The number on the digital display should

be zero (0). If not, see page 1-5 for complete information on

normal operating characteristics.

Step 2

Your CO and Gas alarm is equipped to be mounted as a cord-

ed unit (recommended for natural gas detection), a direct

plug unit (recommended for propane gas detection) or a

table top unit. In the “as shipped” configuration, the unit can

be plugged directly into a wall socket. (If your outlets are

mounted horizontally, please refer to page 1-4). If the trans-

former/adapter is taken out of the unit, the unit can be

mounted high on the wall, while the transformer is plugged

into a wall socket. The explosive Gas you use will determine

if the unit should be mounted high on the wall (cord option)

or low on the wall (direct plug option). Refer to page 1-4 for

further information on installing your alarm.

Step 6

Wait 2 to 3 minutes after power up and make sure the red dot

in the digital display is blinking. Then test the unit’s operation

by pressing and releasing the Test/Reset button. Within 15

seconds you hear 3 slow beeps with “GAS” appearing in the

digital display. Then, you will hear 4 quick beeps followed by

5 seconds of silence then 4 quick beeps repeating while a

number (usually around 200) is displayed. In normal opera-

tion, the repeating slow beeps with “GAS” showing in the dis-

play is the alarm condition notifying you that either natural

Gas or propane is being detected. The 4 quick beeps 5 sec-

onds of silence -repeating while a number is shown in the

digital display indicates that the alarm is in a condition noti-

fying you that carbon monoxide is being detected. For com-

plete testing information, refer to page 1-5.

Step 3

A 9V battery is needed for backup in the event of a power

outage. When installing the battery, use an Energizer 522,

Duracell MX 1604 or, for extended life, use an Ultralife lithi-

um power cell model U9VL. Any of these batteries can be

purchased where you bought the alarm or at your local hard-

ware store. To install the battery, open the back door and

snap battery connector onto battery. You will hear the alarm

sound briefly to indicate the unit is receiving power. Place

battery into battery compartment and replace back door

(refer to page 1-1).

Step 7

While testing the alarm, have someone else check that the

alarm can be heard easily from the sleeping areas. The unit

should be located where it can wake you if it alarms at night.

See page 1-3 for complete information on the best locations

for your alarm.

Step 4

First install the 9V battery then plug the alarm into a standard,

unswitched 120 volt AC electric outlet in one of the configu-

rations listed in step 2.

Caution: Continuous exposure to the loud 85 decibel alarm

at close range over an extended period of time may cause

hearing loss. We recommend that you cover the sound holes

while testing.

That’s it. Your Nighthawk CO and Gas alarm is now moni-

toring for the presence of carbon monoxide and explosive

Gas.

Download from Www.Somanuals.com. All Manuals Search And Download.

P a r t On e – Yo u r Nig h t h a w k CO a n d Ga s Ala r m

Ab out Your CO a nd Ga s Ala rm

Nighthaw k CO and Gas Alarm – rear view

Rem ovable

Adapter

The number one feature that sets Nighthawk apart from other

alarms is its unique digital display that gives you a continuos read-

out of CO levels from 30-999 parts per million and an easy method

for determining if Gas is being detected. The digital display serves

as an early warning of CO or Gas presence.

Thum b Grip for

Back Door

Rem oval

Adapter

Thum b

Release

(Slide Dow n)

Nighthawk is the only CO and Gas alarm that gives you the choice

of a direct-plug, a 6' power cord or table top unit all in one.

Depending on how or where you wish to mount your unit, you

can get exactly what you need for a perfect application. These are

just a few reasons over 4.5 million families have chosen Nighthawk

over every other brand for this kind of life-saving protection.

Door “Latches”

at all four

corners of

Back Door

back door

Nighthaw k CO and Gas Alarm (KN-COEG-3) – front view

Cord

Recess

Key Holes

Carbon

Monoxide

Alarm

Explosive

Gas

Alarm

Digital

Display

Slide Support for

Table Top and Direct Plug Use

Rear view w ith back door removed

9V Backup

Battery

(shown

Pow er

Cord

Blinking

Red Dot

TEST-RESET

PEAK LEVEL

Test/Reset

Button

installed)

Adapter

Cord Strain

Relief

Battery

Connector

Peak Level

Button

Sounder

Alarm

Install 9V

battery provided

as show n

1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

P a r t On e – Yo u r Nig h t h a w k CO a n d Ga s Ala r m

Nig htha w k ’s Uniq ue Fea tures

Wha t Ca rb on Monoxid e a nd Exp losive Ga s Ala rm s

Digital Display

Ca n a nd Ca nnot Do

This unit is designed to sense unacceptable levels of CO or Gas from

malfunctioning furnaces, appliances, Gas engines or other sources.

The continuous digital display shows you the level of carbon monoxide

(if any) the unit is sensing as well as if Gas is present. The unit updates

this reading every 15 seconds so you can watch levels rise or fall.

Note: If the unit does not sense any CO or gas, the reading is zero (0).

In most homes, the unit reads “0” all the time. A reading of “0” is

expected under normal conditions, and is good. The blinking dot after

the number shows you the unit is operating.

This unit will provide early warning of the presence of carbon

monoxide, usually before a healthy adult would experience symp-

toms. It will provide warning of a Gas condition before 25% of the

LEL for methane or propane is detected.

This early warning is possible, however, only if your Nighthawk CO

and Gas alarm is located, installed and maintained as described in

this user’s guide.

Test/Reset Button

This button has three functions. First, this is the button you press when

you test the unit monthly (see page 1-5 for further details). Secondly,

you press this button if the unit alarms and you want to silence the

alarm. This will reset the unit and it will then again start monitoring for

CO or Gas, if CO concentration is above 70 ppm the alarm will again

sound within 6 minutes. It’s also used when resetting the peak level

memory. (See page 1-7).

When on AC power, this unit is designed to act as a continuous mon-

itor, it is not designed for use as a short-term testing device to per-

form a quick check for the presence of CO or Gas.

Alarms have limitations. Like any other electronic device, CO and Gas

alarms are not fool-proof.

Peak Level Button

By pressing this button, you can see the peak CO level recorded by

the alarm since it was last cleared or unplugged. This Nighthawk fea-

ture allows you (or heating contractor or fireman) to see exactly how

big a CO problem you have so you can react accordingly. (More on the

peak level memory feature on page 1-7).

CO and Gas alarms have a limited operational life. You must test your

CO and Gas alarm monthly, because it could fail to operate at any

time. If your CO and Gas alarm fails to test properly, or if its self-diag-

nostic test reveals a malfunction, immediately have the unit replaced.

See back page for warranty information.

Sensors

CO and Gas alarms can only sense CO that reaches the unit’s sensor.

Carbon monoxide may be present in other areas without reaching

the alarm. The rate at which CO reaches the unit may be affected by

doors or other obstructions. In addition, fresh air from a vent or open

window or any other source may prevent CO from reaching the sen-

sor. Please observe cautions on page

The CO sensor is a highly sensitive, electrochemical sensor that is CO-

specific to help avoid false alarms. Turn to page 1-7 for more

information on how to care for and protect the alarm.

The Gas sensor is a metal oxide sensor designed to detect natural gas

(methane) or propane.

Sounder Alarm

1-3 “Where to install your alarm.”

This is the loud 85 decibel pulsing alarm that will sound to alert you to

a potential problem. Alarm condition for CO is 4 quick beeps – fol-

lowed by 5 seconds of silence – followed by 4 quick beeps. Repeat with

a number showing in the display (CO concentration in PPM). The alarm

pattern for Gas is a 1/2 second alarm on, 1/2 second of silence -

repeating with “GAS” shown in the display.

Caution: Continuous exposure to this sound level at close range over

an extended period of time may cause hearing loss. We recommend

you cover the sounder with your finger while testing. More on testing

on page 1-5,6.

CO or Gas could be present on one level of the home and not reach

the alarm installed on a different level. For example, CO or Gas in

the basement may not reach an alarm on the second level, near the

bedrooms. For this reason, we recommend you provide complete

coverage by placing a CO and Gas alarm on every level of the home.

This unit is not a smoke alarm. It will not sense smoke or fire. For

early warning of fire you must install smoke alarms, even though car-

bon monoxide can be generated by a fire.

CO and Gas alarms are not a substitute for property, disability, life or

other insurance of any kind. Appropriate insurance coverage is your

responsibility. Consult your insurance agent.

Keyholes

When the alarm is mounted to the wall, these keyholes slide onto the

screws in the wall. (See “How to install your alarm on page 1-4).

Your CO/Gas alarm is not designed to continually detect explosive

gas while on battery only operation. The CO/Gas alarm is provided

with a 9 volt battery backup for short term protection against the

presence of carbon monoxide or explosive gas. For the first four min-

utes after the unit goes into battery backup operation, the explosive

gas sensor will operate as if on AC power. However, after four min-

utes, to extened battery life, the unit will go into battery conserve

mode and will only sample for explosive gas once every eight min-

utes. Explosive gas could be present during this 8-minute period

without the unit going into alarm.

Pull-Out Transformer/Adapter

This unique Nighthawk feature enables the alarm to be used as a direct

plug unit, a wall mounted unit or a table top unit. More on how this

unique feature is used for different application, page 1-4.

9V Backup Battery

This CO and Gas alarm is not battery operated. The 9V battery is to

supply a short-term backup during a power outage. In the event of a

power outage, a fully charged 9V battery will continue operating

the CO alarm for at least 20 hours, unless Gas is detected during

battery backup conditions. This will significantly shorten the bat-

tery life.

1-2

Download from Www.Somanuals.com. All Manuals Search And Download.

P a r t On e – Yo u r Nig h t h a w k CO a n d Ga s Ala r m

W h e re t o In s t a ll Yo u r CO a n d Ga s Ala r m

WHEN CHOOSING YOUR INSTALLATION LOCATIONS,

MAKE SURE YOU CAN HEAR THE ALARM FROM ALL SLEEP-

ING AREAS.

W h e re No t t o In s t a ll Yo u r CO a n d Ga s Ala r m

To avoid causing damage to the unit, to provide optimum pro-

tection, and to prevent unnecessary alarms, follow the direc-

tions below where NOT to install this alarm:

Mounting Configuration

It is not recommended that you install this CO and Gas alarm in

garages or kitchens. Installation in these areas could lead to nui-

sance alarms, may expose the sensor to substances that could

damage or contaminate it, or the alarm may not be heard by

persons in other areas of the home, especially if they are sleeping.

Since CO generally mixes well with air, mounting the Nighthawk

CO and Gas alarm should depend on the type of explosive Gas

you intend to detect. If you are not certain which type of Gas you

are using in your home, please read about natural Gas and

propane in the introduction on page i.

In the garage, vehicle exhaust can contain some carbon monox-

ide. These levels are higher when the engine is first started. Within

hours of starting a vehicle and backing it out of the garage, the lev-

els present over time can activate the alarm and become a nuisance.

If you are a user of natural Gas, we recommend you mount

your Nighthawk unit high on the wall (no closer than 6 inches

from the ceiling) using the extendable cord feature to ensure the

earliest opportunity to detect a Natural Gas leak.

In the kitchen, some Gas appliances can emit a short burst of CO

or Gas upon start-up. This is normal. If your CO and Gas alarm is

mounted too close to these appliances, it may alarm often and

become a nuisance.

If you are a user of propane, we recommend you mount your

Nighthawk near the floor (using the direct plug-in feature) to

ensure the earliest opportunity to detect a propane leak.

If you must install a Nighthawk CO and Gas alarm near a cooking

or heating appliance, install AT LEAST 5 feet away from appli-

ance.

LOCATION

Your Nighthawk CO and Gas alarm should be mounted in or

near bedrooms and living areas or wherever you suspect a CO

or Gas exposure is likely. It is recommended that you install a

Nighthawk CO and Gas alarm on each level of a multi-level

home.

In the event of a CO alarm, two self-adhesive labels are includ-

ed with the CO and Gas alarm. Add the phone number of your

emergency service provider in the space provided. Place one

label next to the alarm and one label near a fresh air source such

as a door or window.

CAUTION: This alarm will only indicate the presence of carbon

monoxide or Gas at the sensor. Carbon monoxide or Gas may be

present in other areas.

IMPORTANT: Improper location can affect the sensitive elec-

tronic components in this alarm. Please see the next section

describing where NOT to install this alarm.

Recom m ended Locations

Upper Levels of Hom e

DINING

KITCHEN BEDROOM BEDROOM

LIVING ROOM

BEDROOM

1-3

Download from Www.Somanuals.com. All Manuals Search And Download.

How to Insta ll Your Ala rm

Do not install in excessively dusty, dirty or greasy areas such as

kitchens, garages and furnace rooms. Dust grease or household

chemicals can contaminate or coat the alarm’s sensors, causing the

alarm not to operate properly.

Your Nighthawk CO and Gas alarm with its removable adapter

allows you to install the alarm as a wall mounted unit (for nat-

ural Gas detection and CO), a direct plug unit (for propane and

CO), or as a table top unit.

Do not obstruct the vents located at the top and bottom of the

alarm. Place the alarm where drapes, furniture or other objects do

not block the flow of air to the vents.

To install the battery, open the back door and snap battery

connector onto battery. You will hear the alarm sound briefly to

indicate the unit is receiving power. Place

battery into battery compartment and replace

back door.

Do not install in dead air spaces, such as peaks of vaulted ceilings

or gabled roofs, where carbon monoxide or Gas may not reach the

sensor in time to provide early warning.

Do not install in turbulent air from ceiling fans. Do not install near

doors and windows that open to the outside, near fresh air vents,

or anywhere that is drafty. Rapid air circulation from fans or fresh

air from outside may cause the sensors to display an inaccurate

readings.

Direct Plug Alarm

First, refer to “Where to Install Your CO and

Gas alarm” on page 1-3 for general guidelines

as to where to locate your CO and Gas alarm.

In its “as shipped” configuration, your

Nighthawk CO and Gas alarm is ready to be

plugged directly into a close to the floor wall

Do not install this alarm in a switch- or dimmer-controlled outlet.

Do not install in areas where the temperature is colder than 40˚F

(4.4˚C) or hotter than 100˚F (37.8˚C). These areas include uncondi-

tioned crawl spaces, attics, porches and garages. Extreme tempera-

tures will affect the sensitivity of the alarm.

Back of unit w hen

socket. This is the recommended

used as direct plug

for CO and

propane detection.

configuration for detecting CO and propane.

To install:

1. Choose a standard 120V outlet to plug alarm into.

Do not install this unit near deep cell large batteries. Large batter-

ies have emissions that can cause the alarm to perform at less than

optimum performance.

2. Pull slide support out approximately .25” until slide snaps in

place (this will help support unit in wall outlet).

3. Simply plug in.

Avoid the following:

•

Excessive spillage or reverse venting of fuel burning

appliances caused by outdoor ambient conditions, such as:

1) Wind direction and/or velocity, including high gusts

of wind. Heavy air in the vent pipes (cold/humid air with

extended periods between cycles). 2) Negative pressure

differential resulting from the use of exhaust fans.

3) Simultaneous operation of several fuel burning appliances

competing for limited internal air. 4) Vent pipe connections

vibrating loose from clothes dryers, furnaces or water heaters.

5) Obstructions in or unconventional vent pipe designs which

can amplify the above situations.

If outlet is m ounted horizontally (sidew ays):

If you are going to use your alarm as a direct

plug and you are going to plug in to an out-

let that is mounted horizontally (sideways),

you will need to rotate the adapter 90˚. This

simple process is outlined below.

To rotate adapter:

1. With back of unit facing you (with adapter

at top), place your thumbs on thumb grips.

2. With your thumbs, push down in the

direction of the arrows on the thumb grips

and slide back door off.

•

Extended operation of unvented fuel burning devices (range,

oven, fireplace, etc.).

Temperature inversions which can trap exhaust Gasses near

the ground.

Car idling in an open or closed attached garage, or near

a home.

3. Next, place your thumbs on the adapter

thumb releases.

4. Spread adapter thumb releases out and

Back of unit w hen

used as direct plug

for sidew ays outlet

carefully turn alarm over. This will allow adapter to slide out.

5. Rotate the adapter 90˚ to the right (clockwise), and snap

firmly back into place.

6. Carefully replace back door by making sure “latches” on all

four corners of door are lined up, then firmly press into place.

7. Now simply plug in to outlet.

1-4

Download from Www.Somanuals.com. All Manuals Search And Download.

P a r t On e – Yo u r Nig h t h a w k CO a n d Ga s Ala r m

Wall Mounted Alarm

No r m a l Op e r a t in g Ch a r a ct e r is t ics

When you first pow er up the unit, the alarm will sound briefly

to let you know the unit is receiving power and that the alarm circuit

is functioning.

First, refer to “Where to Install Your CO

and Gas alarm” on page 1-3 for general

guidelines as to where to locate your CO

and Gas alarm.

You should see three eights

on the digital display, indicating

Installation tips for power cord models:

The power cord option provides more

flexibility in mounting locations and

allows the alarm to be easily installed at

eye level.

the alarm is in the start-up mode. The three eights will remain for

approximately 20 seconds. You should see a

blinking red dot to the lower right of the digi-

tal display. The blinking dot shows that the

alarm is operating.

Note: If you mount the alarm high on a

wall, make sure it is at least 6" from the

ceiling. Any higher than this, it will be in

“dead air space” and carbon monoxide or

natural Gas may not reach the sensors.

Within 20 seconds, your CO alarm will start

monitoring for CO. Within 2 minutes your

alarm will start monitoring for Gas. Note: The number will probably

be zero (0). This is a normal condition for most households and

shows that no measurable amount of CO or Gas is being detected.

Blinking Dot

Back of unit w hen used

as a w all m ount for

natural gas and CO

detection

The alarm has begun monitoring the air for carbon monoxide and Gas

and will continue to do so as long as it receives power.

Note: Do not cover the alarm with a curtain.

For a wall-mount, you will need to pull out the removable

adapter and power cord. This simple process as outlined below.

When the alarm is unplugged or loses pow er and you have

a good 9V battery installed, the alarm will automatically switch

to its battery backup mode and you will notice the following:

To install:

•

After 4 minutes the digital display will show a blinking dot

only – this helps conserve the battery’s power.

1. Follow steps 1 - 4 in the previous column under “To Rotate

Adapter.”

2. With adapter out, pull out power cord and unwrap it.

3. With cord extended, press last few inches into cord recess.

Gently pull cord at bottom of cord recess until cord becomes

taught and lays flat in cord recess.

•

The digital display will show a number for CO or show

“GAS” only if it senses carbon monoxide or Gas while in

backup mode.

•

If CO is detected while on battery backup, alarm pattern

is 4 quick beeps – followed by 5 seconds of silence –

followed by 4 quick beeps. After 4 minutes, this alarm pattern

occurs only every 60 seconds.

WALL

4. Carefully replace back door by making sure

“latches” on all four corners of door are lined up,

then firmly press into place.

If Gas is detected while on battery backup, the unit will display

Gas and alarm continuously. The alarm pattern for Gas is a 1/2

second alarm on, 1/2 second of silence -repeating. For the first

four minutes after the unit goes into battery backup operation,

the explosive gas sensor will operate as if on AC power.

However, after four minutes, to extened battery life, the unit will

go into battery conserve mode and will only sample

for explosive gas once every eight minutes. Explosive gas could

be present during this 8-minute period without the unit going

into alarm. If the alarm is on battery backup for an extended

period of time, replace the battery to ensure maximum protect-

tion is provided. The battery will last only a couple hours in a

Gas alarm condition.

5. Insert the screws provided until head is approx.

1/8” from wall (If mounting in plaster board or dry-

wall, drill 3/16 hole and use plastic anchor provid-

ed). Use mounting guide template in back of user’s

guide to locate holes.

1/8"

6. Hook the Nighthawk CO and Gas alarm unit over the screw

onto keyhole in back of unit.

7. Plug cord into electrical outlet.

Table Top Alarm

Note: When AC power is restored, the alarm will automatically switch

back to normal operating mode.

You can also use your Nighthawk CO and Gas alarm as a table top

unit. Simply follow the above steps for removing adapter, then

instead of mounting to a wall, simply pull out slide support and

stand on table, bedside stand, chest of drawers, etc. (refer to diagram

on page 1-1).

When the alarm is unplugged or loses pow er and you have

a low battery installed, you will notice the following:

•

A fading alarm will sound alerting you the unit has

switched to its backup mode, but the 9V battery is low.

1-5

Download from Www.Somanuals.com. All Manuals Search And Download.

P a r t On e – Yo u r Nig h t h a w k CO a n d Ga s Ala r m

•

A blinking dot will be displayed and the sounder will chirp

every 15 seconds.

How to Test Your Ala rm (continued )

NOTE: Pressing the Test/Reset button tests the functions of the

alarm’s internal components, circuitry and micro-computer. YOU

DO NOT NEED TO PRESS THE TEST BUTTON TO TAKE A CO

OR GAS READING. CO readings or the presence of Gas are

automatically shown on the alarm’s digital display. If the alarm

shows zero (0), then no measurable amount of CO or Gas has

been sensed by the alarm within the past 15 seconds.

•

The display will alternate between “Lb.” (low battery) and

CO reading while chirping.

When battery is depleted:

•

A blinking dot will be displayed and the sounder will chirp

approximately every 30 seconds.

•

Pressing the test button will result in a chirp approximately

every one second. The alarm will not detect CO or gas if

battery is depleted. Replace battery.

Testing the sensor resp onse

Constant exposures to high or low humidity may

reduce battery life.

While it is not required, on occasion you may wish to observe

and become familiar with your alarm’s response in the actual

presence of carbon monoxide or Gas. The best and safest way

to do this is with either a cigarette or an incense stick. To per-

form this test you will need: your alarm, a butane lighter, an ash-

tray, and either a cigarette or an incense stick.

We recommend you replace your 9V battery at

least every six months.

How to Test Your Ala rm

CAUTION: Please refer to the “Frequently Asked Questions”

section for warnings on how NOT to test the sensor response.

There are two aspects of the alarm’s operation that can be test-

ed: the electronics and the sensors response. Instructions on test-

ing each are outlined below and on the next page.

WARNING: This test should be done by adults only. Children

should be warned never to light matches or butane lighters.

Please use caution when performing the test described below.

Avoid burns from flame or hot materials. Avoid inhaling exces-

sive smoke from the cigarette or incense stick. Extinguish all

flames and properly discard all hot materials.

Testing the Electronics

You should test the alarm once a month, following the direc-

tions listed below. If at any time you test the alarm and it does

not perform as described below, have it replaced immediately.

Turn to page 1-6 “How to know if your alarm is malfunctioning”

for a description of the characteristics of a malfunctioning alarm

and what you should do if a malfunction occurs.

CARBON MONOXIDE TESTING

Step 1. With a match or a lighter, light a single cigarette or

incense stick. Extinguish the match or lighter. Make sure an

ashtray is available to discard ashes, matches and the burned

cigarette or incense stick.

Observe the alarm weekly to make sure the red

dot is blinking, indicating normal operation.

If the dot is not blinking, unplug the alarm

for three minutes, then plug in again. This

will clear the alarm for restart. If the dot does

not resume blinking, your alarm may be malfunctioning.

Step 2. Hold the smoldering cigarette or incense stick 2-3 inches

directly below the bottom air vents of the CO and Gas alarm,

making sure the stream of smoke rises into the vents.

Blinking Dot

To test the alarm, press the Test/Reset button. If the unit is

operating properly, you should notice the following:

Step 3. Continue holding the cigarette or incense stick directly

below the alarm for 3 - 5 minutes or until you see a reading on

the display. Note: Do not hold the cigarette or incense stick clos-

er than one inch to the alarm as smoke will cause a yellow stain

to develop on the alarm’s outer case.

•

The display shows three eights

, then shows the

word “GAS” in the display while the unit is sounding 3

half second beeps. Then, the display shows a number (usu

ally around 200). You should then hear 4 quick beeps –

followed by 5 seconds of silence – followed by 4 quick

beeps repeating until reset stops. The unit will then show

the three eights for several seconds. It will then return to

monitoring for carbon monoxide and Gas.

Step 4. Your unit will probably not alarm during this test. If it

does, you can silence it by pressing Test/Reset button and remov-

ing the source of CO.

Step 5. Extinguish the cigarette or incense stick by pressing the

smoldering tip into the ashtray.

Familiarize yourself and household members with the alarm pat-

tern described above for a Gas event and a CO event. While on

AC power, in the event of a CO or Gas incident, the appropriate

pattern will continue to repeat as long as CO or Gas is present.

1-6

Download from Www.Somanuals.com. All Manuals Search And Download.

P a r t On e – Yo u r Nig h t h a w k CO a n d Ga s Ala r m

GAS TESTING

Lo w Ba t t e r y Wa r n in g

If the 9V battery is missing, or if the battery’s power is low, an “Lb”

message will display which blink’s alternately with the current CO

reading or “GAS” every second. If this happens, you need to replace

the battery. Refer to page 1-5 for more on low battery warnings.

Step 1. With a butane lighter, press the button of the lighter

without activating the flint. Ensure no heat source or spark is

present near you when performing this test.

Step 2. While holding the button of the lighter down, insert the

orafice of the lighter into the vents on the front of the unit. Hold

for 30-60 seconds or until alarm activates.

What to do if you’re not sure...

PLEASE familiarize yourself with the malfunction alert, and do not

confuse these signals with an alarm. After reading the information

above, if you are still unsure whether your alarm is operating prop-

erly, call the KIDDE Safety toll-free consumer hotline at 800-880-

6788 to do a quick diagnostic check of the alarm over the phone.

The customer service representative will be able to assist you and

answer your questions.

Step 3. After the alarm condition is achieved, remove the lighter

and gently blow in the same area to remove the gas.

Ho w t o Kn o w If Yo u r Ala r m is M a lfu n ct io n in g

Your alarm performs an internal self-diagnosis every 15 seconds to

make sure that it is functioning properly. The alarm is designed to

alert you in the unusual event of a malfunction.

If your alarm sounder is beeping, and you are not sure if it is a CO

and Gas alarm or a malfunction alert, reset the alarm, open win-

dows for ventilation, extinguish all open flames, do not activate

any electrical switch and evacuate the premises immediately. Then

call the KIDDE Safety toll-free consumer hotline at 800-880-6788

for assistance.

If the alarm m alfunctions.

In the rare event that your alarm malfunctions, it will alert you with

one of these signal groups (depending upon the type of

malfunction that occurs):

Malfunction Signal Group 1 - Com ponent Failure

– An intermittent “chirping” alarm will sound every 30 secs., and

– An “Err” message will appear on the digital display

OR,

Malfunction Signal Group 2 - Microprocessor Failure

– The alarm will sound continuously, and

– The digital display will be blank, and

– The alarm cannot be shut off by pushing “Test/Reset” button

Unplug the alarm immediately and return for warranty exchange

(see “Warranty” on back page).

1-7

Download from Www.Somanuals.com. All Manuals Search And Download.

P a r t On e – Yo u r Nig h t h a w k CO a n d Ga s Ala r m

The peak level feature is helpful in identifying low level CO occurrences

Ho w t o Kn o w If Yo u r Ala r m is M a lfu n ct io n in g

(co n t in u e d )

Never ignore an alarm. A true alarm is an indication of poten-

tially dangerous levels of carbon monoxide or Gas.

below 30 PPM. Although the unit will not automatically display levels below

30 PPM, it will detect and store these readings in memory. By pressing the

peak level button, concentration levels as low as 11 and up to 999 PPM will

be displayed. Gas events will not be displayed when pressing the peak level

memory button.

Concentrations of CO between 0 and 30 PPM can often occur in normal,

everyday conditions. Concentrations of CO below 30 PPM may be an indi-

cation of a transient condition that may appear today and never reappear.

Just a few examples of conditions and/or sources that may cause low level

readings are heavy automobile traffic, a running vehicle in an attached

garage, an appliance that emits CO when starting up, a fire in a fireplace or

charcoal in a nearby barbecue. A temperature inversion can trap CO gen-

erated by traffic and other fuel burning appliances causing low level read-

ings of CO.

Ho w t o Ca re fo r Yo u r Ala r m

To keep your alarm in good working order, you must follow

these simple steps:

W HAT YOU SHOULD DO:

•

Test the alarm once a month by pressing the Test/Reset

button (see page 1-5,6).

•

Vacuum the alarm cover once a month to remove

accumulated dust. Use the soft brush attachment of your

vacuum cleaner, and unplug the alarm from the electrical

outlet before vacuuming.

Normally, the digital display will read “0” and under certain conditions you

may notice levels of 30 or more for short periods of time, by using the Peak

level memory feature on the Nighthawk alarm you can view concentrations

of CO between 11 and 30 PPM. Use the low-level concentrations shown in

memory as a tool in identifying the source of the CO. It may be helpful to

purchase additional Nighthawk alarms to place in different locations through-

out your house to isolate the CO source. Monitor the CO concentrations

shown in the peak level memory to see if readings occur in certain areas at

certain times of the day, or near a particular appliance.

Once the source is located, correcting the problem may be as easy as open-

ing a window, venting an appliance, backing a car out of the garage a safe

distance from living quarters, closing the garage door, and letting the car

warm up outside. It could be possible that a weather condition caused the

low-level reading and the condition may or may not happen again.

Some CO conditions may start out as low level leaks but could develop into

CO concentrations that could become harmful. If this happens, the CO and

Gas alarm will detect the dangerous level and alarm, notifying you and oth-

ers of the conditions. DO NOT ignore high concentration readings above 30

PPM or a CO and Gas alarming device that is in alarm. Refer to page 4-1 for

more details.

CO concentrations displayed below 30 PPM in memory are for reference

only and the accuracy of the concentration shown may not be as accurate as

noted on page 5-1.

•

Instruct children never to touch, unplug or otherwise interfere

with the alarm.

W HAT YOU SHOULD NOT DO:

•

Never use detergents or solvents to clean the alarm.

Chemicals can permanently damage or temporarily

contaminate the sensor.

Avoid spraying air fresheners, hair spray, paint or other

aerosols near the alarm.

Do not paint the alarm. Paint will seal the vents and

interfere with proper sensor operation.

Do not mount the alarm directly above or near a diaper pail,

as high amounts of methane Gas can cause a Gas alarm.

•

Note: If you will be staining or stripping wood floors or furniture,

painting, wall-papering, or using aerosols or adhesives for a do-it-

yourself project or hobby, before you begin: Remove the alarm

to a remote location to prevent possible damage to or conta-

mination of the sensor. You may wish to unplug the alarm and

store in a plastic bag during the project.

The following is a list of substances that at high levels can affect

the sensor and cause an alarm.

Methane, propane, iso-butane, ethylene, ethanol, alcohol,

carbon monoxide, iso-propanol, benzene, toluene, ethyl

acetate, hydrogen, hydrogen sulfide, sulfur dioxides.

Also most aerosol sprays, alcohol based products, paints,

thinners, solvents, adhesives, hair sprays, aftershaves, per-

fumes, auto exhaust (cold start) and some cleaning agents.

To Reset the P ea k Level Mem ory…

Step 1. Press the peak level button.

Step 2. With the peak level button still pressed, press the test/reset but-

ton for two seconds and release.

The P ea k Level Mem ory Button

The number on the display will turn to “0”. The memory has now been

cleared and the alarm will begin monitoring for CO and Gas within a few

minutes.

Although the peak level feature will display levels below 30 PPM of CO,

these levels will not result in an alarm no matter how long the device is

exposed to these levels.

1-8

Download from Www.Somanuals.com. All Manuals Search And Download.

P a r t Tw o – Ca r b o n M o n o x id e a n d Ga s

Long term exposure to low levels could cause permanent heart and

brain damage.

W h a t is Ca r b o n M o n o x id e ?

Carbon monoxide (CO) is an odorless, colorless, poisonous Gas cre-

ated when any fuel is burned – Gasoline, propane, natural Gas, oil,

wood, coal, and even tobacco. When combustion air is limited, more

CO is produced. Serious problems can develop when combustion

by-products are not properly vented outside the house.

Co u ld Yo u r Fa m ily b e a t Ris k fo r CO P o is o n in g ?

Carbon monoxide is the number one cause of poisoning deaths in

the United States. According to the Mayo Clinic, at least 10,000

Americans are affected by CO poisoning each year.

You’ve probably heard about carbon monoxide poisoning in the

news recently. It’s a problem receiving more attention because

groups like the American Lung Association and the Consumer

Product Safety Commission have made it a priority to warn the pub-

While anyone is susceptible, experts agree that unborn babies, small

children, senior citizens and people with heart or respiratory prob-

lems are especially vulnerable to CO and are at the

greatest risk for death or serious injury.

lic about the dangers of this deadly household poison

W h e re Do e s CO Co m e Fro m ?

W h a t is Na t u r a l Ga s ?

Inside your home, appliances used for heating and cooking are the

most likely sources of carbon monoxide. Vehicles running in attached

garages can also produce dangerous levels of carbon monoxide.

Natural Gas is typically supplied through a main utility line connect-

ed to your home. If you do not live in a rural area you are likely to

be a user of natural Gas. It is the dominant energy used for home

heating with about 55 percent of American homes using Gas. Natural

Gas is a fossil fuel comprised almost entirely of Methane. Methane is

much lighter than air and will rise rapidly in air. If you are a user of

natural Gas, we recommend you mount your Nighthawk unit 12

inches away from the ceiling (using retractable cord feature) to

ensure the earliest opportunity to detect a leak.

A by-product of combustion, carbon monoxide can be a potential

problem from a number of common sources – automobiles,

furnaces, water heaters, fireplaces, wood stoves, charcoal grills, Gas

ranges, space heaters and portable generators.

When these appliances are in good working condition with

proper ventilation, lethal carbon monoxide Gas is vented outdoors

where it quickly disperses. But even the slightest malfunction or mis-

use of any of these sources can lead to a build-up of carbon monox-

ide in your home that can become deadly before you’d even know

it’s there.

W h a t is P ro p a n e ?