2172
DO NOT INSTALL THIS KIT ON VEHICLES WITH
COMPOSITE LEAF SPRINGS. THIS KIT IS COMPATIBLE
WITH STEEL LEAF SPRINGS ONLY.
WARNING:
Do not inflate this assembly when it is
unrestricted. The assembly must be restricted
by the suspension or other adequate structure.
Do not inflate beyond 100 psi Improper use or
over inflation may cause property damage or
severe personal injury.
Installation of this kit requires a
minimum of 6-1/2" of clearance between
the tire side wall and the frame.
Your kit includes separate inflation valves and air lines
for each air helper spring. This will allow you to level your
vehicle from side to side as well as from front to back. If you
would rather have a single valve inflation system, your
dealer can supply the required "T" fitting.
INSTALLATION INSTRUCTIONS
Congratulations-yournewAirHelperSpringsarequality
products capable of improving the handling and comfort of
your vehicle. As with all products, proper installation is the
key to obtaining all of the benefits your kit is capable of
delivering. Please take a few minutes to read through the
instructions to identify the components and learn where and
how they are used. It is a good idea to start by comparing the
parts in your kit with the parts list below.
IMPORTANT!
For your safety and to prevent possible damage to your
vehicle, do not exceed the maximum load recommended by
the vehicle manufacturer (GVWR). Although your Air Helper
Springs are rated at a maximum inflation pressure of 100
psi, this pressure may allow you to carry too great a load on
some vehicles. It is best to have your vehicle weighed once
it is completely loaded and compare that weight to the
maximum allowed. Check your vehicle owner’s manual for
maximum loads listed for your vehicle.
The heart of the air helper spring kit is, of course, the air
springs. Remember that the air helper springs must flex and
expand during operation, so be sure that there is enough
clearance to do so without rubbing against any other part of
the vehicle.
Besuretotakeallapplicablesafetyprecautionsduringthe
installation of the kit. The instructions listed in this brochure
and the illustrations all show the left, or driver’s side of the
vehicle. To install the right side assembly simply follow the
same procedures.
When inflating your Air Helper Springs, add air pres-
sure in small quantities, checking pressure frequently dur-
ing inflation. The air spring requires much less air volume
than a tire and, therefore, inflates much quicker.
TOOLS REQUIRED
• (2) 9/16" END WRENCHES
• (2) 1/2" END WRENCHES
• UTILITY KNIFE
• 5/16" DRILL BIT
• 3/8" DRILL BIT
• ELECTRIC DRILL
PARTS LIST
AIR SPRING
UPPER BRACKET
LOWERBRACKET
BRACKET STRAP/SHIM 1/2" 5086
BRACKET STRAP/SHIM 1"
AIR LINE TUBING
9001
5376
5092
2
2
2
4
4
1
16
6
8
6
2
3/8"-16 X 1 1/2 HEX BOLT
5/16" FLAT WASHER
PUSH-TO-CONNECT
INFLATION VALVE
INFLATION VALVE CAP
PUSH-TO-CONNECT
ELBOWFITTING
THERMAL SLEEVE
NYLON TIE
CAUTIONTAG
8
4
2
2
5093
3/8"-16FLANGELOCKNUT
2
2
6
2
3/8"-16 X 3/4" FLANGE HEX BOLT
3/8"-16 x 4-1/2" CARRIAGE BOLT
3/8" SPECIAL WASHER
3/8" FLAT WASHER
21-8136
09-07
NCD-6029-3
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 1 - PREPARE THE VEHICLE
Remove the positive battery cable. With the vehicle on a solid, level surface
chockthefrontwheels. Raisethevehiclebytheaxleandremovetherearwheels.
After the removal of the wheels lower the vehicle so the axle rests on jack stands
rated for your vehicles weight. This installation assumes that there is no load in
the bed of the truck.
STEP 2 - PRE-ASSEMBLE THE KIT
Select one air helper spring and an upper bracket from your kit. Before
attaching the air spring to the upper bracket, thread the air fitting into the spring
see Figure "A". Tighten the air fitting so as to make contact with the nylon ring
and then tighten 1/4 turn to snug the fitting. No thread sealant is needed. Align
thethreadedmountingholesoftheairspringwiththemountingholesoftheupper
bracket and attach the upper bracket using the 3/8" -16 x 3/4" flanged hex bolts.
Select one lower bracket and place the bracket so the lip of the lower bracket will
be next to the tire see Figure "A". Fasten using a 3/8"-16 x 3/4" flange lock bolt
through the center slot into the threaded hole in the air spring (finger tight). Note
that this bolt will be tightened in Step 4.
FRONT
DRIVER'S SIDE
FIGURE "B"
STEP 3 - PRE-FIT AND MARK / DRILL HOLES
FRONT
Position the air spring assembly on the leaf spring stack. The lower bracket
should straddle the leaf spring retainer and the upper bracket mounting flanges
should be flush against the frame. Depending on the application, the lower bracket
mayhavetoberaised(i.e.interferencewith"U"-bolts,leafspringretainer,brakedrum,
etc...). This kit comes with two sets of bracket straps/shims. These are included to
provideadequateclearancefortheairspringandlowerbracket,aswellas,anyother
component on the vehicle. One set is 1/2" tall while the other set is about 1" tall. To
raisetheairspringassemblytoitsmaximumheight,installthe1/2"shimbetween
the lower bracket and the leaf spring stack. The remaining 1" strap/shim will be
used to clamp the assembly to the leaf spring stack see Figure "C". The bracket
straps/shims may be interchanged to provide maximum clearance and proper air
spring height. Furthermore, the shims can be mixed (i.e. use the 1/2" on one side
and the 1" or none on the other) to adjust for leaf spring slant. Keep the upper
and lower brackets as parallel as possible.
FIGURE "C"
Once the height of the lower bracket has been established, adjust the position
of the upper bracket so that the mounting flanges are flush with the side of the
frame rail. Itmaybenecessarytoslidetheentireassemblyforeoraft along the leaf
springinordertoprovidepropermounting. Beforemarkinganddrillingtheholes
for the upper bracket, make sure the mounted height of the air spring is between
7-1/4" - 8-1/2" see Figure "C", and the upper and lower brackets are as parallel
and high as possible. Mark the four holes to be drilled with a center punch using
the upper bracket as a template, then remove the air spring assembly. Before
drilling the holes make sure all electrical, brake and fuel lines are cleared from
the path of the drill. Damage to lines can be avoided by inserting a piece of wood
between the frame rail and any lines in the path of the drill. Drill the four holes in
the frame rail using a 3/8" drill bit see Figure "A".
AIR
SPRINGS
AIR HOSE
INFLATION
VALVES
BUMPER
FIGURE "D"
STEP 4 - INSTALL THE ASSEMBLY TO THE VEHICLE
AIR LINE
After drilling the holes in the frame rail place the assembled air spring and
brackets back on the leaf stack making sure the lower bracket is placed over the
retainer(seeFigure"A"&"B"). Installthe3/8"-16x1-1/2"hexboltsthroughthe
upper bracket holes and the holes that were drilled in the frame rail. Next, fasten
the upper bracket to the frame rail using the 3/8"-16 flange lock nuts and flat
washers see Figure "A". On each side of the vehicle, substitute a standard
washer in place of the special washer in the upper rear location see Figure "A".
Next, attach the lower bracket to the leaf spring assembly. Use the bracket strap/
shim that is not being used as a spacer and fasten the air spring assembly to the
leaf stack using the 3/8"-16 x 4-1/2" carriage bolts and 3/8"-16 flanged lock nuts
see Figure "A". Tighten the air spring to the lower bracket making sure the air
spring is as vertical as possible.
FLAT WASHER
PUSH-TO-CONNECT
INFLATION VALVE
BODY OF
VEHICLE
HEX NUT
VALVE CAP
FIGURE "E"
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 - INSTALLATION OF THE PASSENGER'S SIDE ASSEMBLY
Reverse any orientations when assembling and installing the right, or passenger side of the vehicle.
STEP 6 - INSTALL THE AIR LINE AND THE INFLATION VALVE
Uncoil the air line tubing and cut it into two equal lengths. DO NOT FOLD OR KINK THE TUBING. Try to make the cut as
square as possible. Insert one end of the tubing into the elbow fitting installed in the top of the air helper spring. Push the tubing
into the fitting as far as possible see Figure "A".
Select a location on the vehicle for the air inflation valves. The location can be on the bumper or the body of the vehicle, as
long as it is in a protected location so the valve will not be damaged, but maintain accessibility for the air chuck see Figure "D".
Drill a 5/16" hole and install the air inflation valve using two 5/16" flat washers per valve as supports see Figure "E". Run the
tubingfromtheairhelperspringtotheinflationvalve,routingittoavoiddirectheatfromtheengine,exhaustpipe,andawayfrom
sharp edges. Thermal sleeves have been provided for these conditions. If a thermal sleeve is required simply slide the sleeve
over the air line tubing to the location requiring protection. The air line tubing should not be bent or curved sharply as it may
buckle. Secure the tubing in place with the nylon ties provided. Push the end of the air line tubing into the inflation valve as
illustrated see Figure "E".
STEP 7 - CHECK THE AIR SYSTEM
Once the inflation valves are installed inflate the air helper springs to 70 psi and check the fittings for air leaks with an
applied solution of soap and water. If a leak is detected at a tubing connection then check to make sure that the tube is cut as
square as possible and that it is pushed completely into the fitting. The tubing can easily be removed from the fittings by first
releasing the air pressure then push the collar towards the body of the fitting and then pulling out the tube. If a leak is detected
where the fitting screws into the spring, remove the tubing by pushing the collar towards the body of the fitting and then pulling
out the tube, then screw the brass fitting into the air spring or until the leak stops. Re-install the tubing and reinflate the air
springs and check for leaks as noted above.
This now completes the installation. Install the wheels and torque the lug nuts to the manufactures specifications. Raise the
vehicle by the rear axle and remove the jack stands and lower the vehicle back onto the ground. Re-attach the positive battery
cable and remove the wheel chocks from the wheels. Before proceeding, check once again to be sure you have proper clearance
aroundtheairsprings. Withaloadonyourvehicleandtheairhelperspringsinflated,youmusthaveatleast1/2"clearancearound
the air springs. As a general rule, the air helper springs will support approximately 25 lbs. of load for each psi of inflation
pressure (per pair). For example, 50 psi of inflation pressure will support a load of 1250 lbs. per pair of air helper springs.
FOR BEST RIDE use only enough air pressure in the air helper springs to level the vehicle when viewed from the side (front
to rear). This amount will vary depending on the load, location of load, condition of existing suspension and personal
preference.
NOTE:
Too much air pressure in the air helper springs will result in a firmer ride, while too little air pressure will allow the airhelper
spring to bottom out over rough conditions. Too little air pressure will also not provide the improvement in handling that is
possible. TO PREVENT POSSIBLE DAMAGE MAINTAIN A MINIMUM OF 10 psi IN THE AIR HELPER SPRINGS AT
ALL TIMES.
NOTE:
Once the air helper springs are installed, it is recommended that the vehicle not be lifted by the frame, as over-extension
may occur, resulting in damage to the air helper springs. However, should it become necessary to raise the vehicle by the
frame, deflate both air helper springs completely.
NOTE:
MIN PRESSURE
5 PSI
MAX PRESSURE (LOADED) 100 PSI
Download from Www.Somanuals.com. All Manuals Search And Download.
|