O w n e r ’ s M a n u a l
EO3
Personal In-ear Monitor
wireless system
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for choosing the Nady EO3 Personal In Ear Monitor™ wireless system, we know
you will be very pleased with its performance and features. The EO3 provides high quality,
yet cost-effective in-ear monitoring to on stage performers or behind the scenes personnel.
The system is designed to be very easy to use and requires no installation.
The EO3 consists of one wireless transmitter (EO3-T) and one or more wireless bodypack
receivers (EO3-R) on the same channel. The transmitter features eight factory switchable
channels; the receivers are single channel units that operate on one of eight channels in the
72-76 MHz band, with wide band modulation for quality audio. These frequencies are in a
separate band that will not interfere with simultaneous use of VHF or UHF wireless systems
on the same stage.
The EO3 system has a wireless operating range of 300 feet, which allows it to be used with
confidence in venues from small clubs to large theatres.
The transmitter connects to a monitor or line out from any mixing console, and broadcasts the
audio as an FM signal to any number of pocket size Nady EO3 receivers on the same channel.
Each receiver is equipped with an adjustable volume control, and high performance earbuds.
Earphone enhancers—unique clear soft plastic inserts that can help secure the earbuds—are
included. The transmitter also provides a microphone input to allow wireless cueing of the
performers on stage.
The EO3 can provide a high quality monitor mix at significantly lower decibel levels than
floor monitors. This is an important benefit for artists who wish to protect their hearing
from excessive and potentially damaging sound pressure levels.
Please read this manual completely before using your Nady EO3.
Important Note
Just as with any in-ear monitor system, the EO3 works best when used exclusively by all
the performers on stage—without any wedges or side monitors. The high sound pressure
levels produced by floor monitors (especially if the band plays loud) can bleed through the
in-ear monitor earbuds, in the worst cases, thus hindering their effectiveness. Experiment
with your mix to get the maximum benefit from your EO3.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EO3 Transmitter
The EO3 transmitter is a compact
Connecting audio Input
transmitter that broadcasts on one of eight
channels in the 72-76 MHz band, to any
number of EO3 wireless bodypack receivers
on the same channel. The system provides
a 300 ft. wireless operating range, and
offers these features:
The line In jack (5) on the rear panel lets you
connect the EO3 to your mixing console. This
1/4” mono phone jack accepts an unbalanced
line level audio source at zero dBm nominal
signal level. If your mixer has XLR outputs
only, you will need an XLR-to-phone plug
adapter, available from most electronics
stores and music equipment stores.
• Eight factory switchable channels
• Rear panel input for line level audio
• Front panel input for microphone
• Audio input gain control
• Automatic level control
• Extendible antenna
• 9 volt DC input for AC-EO3 9VDC
regulated power supply adapter provided
• Power switch with red LED power
on indicator
using a Microphone
The Mic jack (7) on the front panel allows
wireless cueing of on stage performers.
Important: This 1/4” mono phone jack is designed
for an electret condenser microphone, and 9V DC
power is present at the input jack. If you wish to
use a conventional dynamic microphone, at least
20 dB more gain is required, and a preamp should
be used. If a preamp is used, be sure to have a
blocking capacitor (1 mfd) between the preamp
output and the EO3 mic input. If a dynamic mic
is plugged into the mic input by mistake, there
should be no damage because the current is
limited to 1.0 mA. If you have any questions,
contact Nady Customer Service (510.652.2411)
or your Nady dealer.
• Audio modulation LED indicator
setting up the Transmitter
Your EO3 requires minimum installation.
Simply place the transmitter on any
flat surface, connect your mixing board
to the transmitter’s back panel input
(See Connecting Audio Input below),
connect the included power supply
(as explained below), and the transmitter is
ready to broadcast to any number of EO3
receivers operating on the same channel.
audio Input Gain adjustment
You can quickly adjust the transmitter to
obtain optimum performance with the
Input Gain control (8). The audio modulation
indicator LED, marked TX (6) will increase in
brightness as the control is turned clockwise,
and decrease in brightness as the control is
turned counterclockwise. When the “TX”
LED is flashing during transmission, the
transmitter is broadcasting properly. (If the
LED stays off continuously or barely flashes
at all, the input gain needs to be increased.
If the LED stays on continuously and does
not flash during modulation, the input is
overloading and needs to be decreased.)
You will also need to test the transmitter in
use with an EO3 receiver. This procedure is
easy to do, and is explained in the receiver
instructions, which follow.
Powering the Transmitter
Connect the AC adapter provided into
the 9V DC jack (1) on the back panel of the
transmitter. Plug the other end into an
AC wall socket. Press Power switch (2).
The Power On leD (3) will light.
antenna
Extend antenna (4) fully and position
90 degrees from top of the transmitter.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the channel can be done quickly
by any qualified service technician.
Contact your dealer or the Nady Customer
Service Department for details.
Confirming Correct Installation
The transmitter’s TX leD (6) will flash
when a microphone or line level signal is
broadcast by the transmitter. If “TX” does
not flash, turn the audio input gain control
clockwise. This will increase audio level
and cause “TX” to flash along with the
program source. When “TX” is flashing,
the transmitter is broadcasting properly.
Test the transmitter with an EO3 receiver.
This procedure is explained in the receiver
instructions.
using More Than One eO3 system
You may operate up to three EO3 systems
in the same location. For example, you may
want to use one transmitter to provide a mix
to the rhythm section, a second to provide
a different mix for the vocalist. For multiple
system operation, please observe:
Note: For the best performance, and to minimize
the possibility of interference from another source,
we suggest you experiment to find the minimal
height the antenna must be extended in order to
perform well in your particular environment.
• If operating two EO3 transmitters in the
same location, use Ch. AA and HH (or GG)
• If operating three EO3 transmitters in the
same location, use Ch. AA, EE and HH
(or GG)
Channel selection
• Locate the transmitters ten feet or more
away from the performers wearing
EO3 receivers
Channel selection is controlled by
DIP-switches inside the transmitter.
The system is preset at the factory.
eO3 Transmitter (Front Panel)
7
6
2
3
eO3 Transmitter (rear Panel)
4
5
8
1
Channel switches (inside)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EO3 Receiver
The EO3 receiver is a pocket sized wireless
audio receiver with an output for earbuds
to provide in ear monitoring, and offers
these features:
using the earbuds
Simply plug the included earbuds into the
earphone jack (2) on top of the receiver.
Note: Proper sound levels on stage are essential
for optimum effectiveness of any in-ear monitor
system. (See also “Important Note” on page 1).
If sound levels are high, it is important to properly
seal out unwanted sound so the earbud can
be effective in providing proper monitoring.
Top high end in-ear monitor systems use special
transducers imbedded in a soft plastic mold of the
users ear canal. This ensures a perfect seal and
maximum immunity from bleed through. Such ear
mold speakers are very expensive and can be
used with the EO3 for optimum results—call
Nady Systems for more information.
• Any number of EO3 receivers can be used
with a single EO3-T transmitter
• Ultra compact and lightweight
• Preset to one of eight channels in the
72-76 MHz range
• Loudness adjustable with volume
control—provides up to 130dB in-ear
monitoring
• Antenna is integral with earphone cord
• A pair of mini binaural EB-3 earphones
included, with optional-use EMI soft
rubber inserts supplied
The EB-3 mono earbud earphones supplied
with the EO3-R receiver offer great sound
and can also provide top results if utilized
properly. If sound pressure levels are high
and bleed through is a problem, care must
be taken to ensure a proper fit and a tight
seal. Although the earphones can often be
used effectively simply as “Walkman”-style
earbuds, for best results in high SPL
environments you must also use the
supplied EMI-S/M/L soft rubber inserts (5).
Choose the correct size (small, medium
or large) from the three sets provided for
a custom fit, and slip over the earphones
before inserting in your ears. Although the
maximum volume available may be slightly
diminished, use of the EMI inserts does
provide a better sound seal, increased
immunity from bleed through and mimics
the results available with custom-made ear
mold speakers.
• LED “Power On” indicator
• Accepts standard 9V alkaline battery
Channel selection
Your receiver is pre-tuned at the factory
to the same channel as your transmitter.
Should you wish to have your transmitter
channel changed, as explained in the
Transmitter section of this manual, you
must also have your receiver(s) retuned as
well. Contact the Nady Customer Service
Department for details.
Powering The receiver
Install a 9V battery in Battery Compartment
(1), observing polarity. To preserve battery
life, always turn the EO3 receiver off
when it is not in use. When the sound
becomes weak or distorted, replace the
battery. The number of hours of operation
per battery is as follows: carbon zinc type
battery: 10-12 hours; alkaline battery
(recommended): 17-20 hours.
Operating the receiver
While wearing your earbuds, turn the
receiver on by rotating the On/Off volume
wheel (3). The Power On indicator (4) will
go on. (To turn the receiver off, rotate the
On/Off/Volume wheel until it clicks, and the
“Power On” indicator will go out.)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
adjusting ear Monitor Volume
Testing receiver range
Listen for your program source, and adjust
receiver volume to a comfortable listening
level. The EO3 receiver is capable of
providing listening levels loud enough to be
heard in use with a rock band. Many bands
use on stage loudness levels that with
repeated exposure could pose a threat to
their hearing. Therefore, it is very important
that the EO3 be used at a reasonable and
comfortable listening level.
Wearing your receiver and earphones, walk
around the stage area (and sound board
and other areas if crew members are to be
equipped with EO3 receivers) and listen for
audio quality. In certain areas of the room
the audio may disappear or “drop out.”
This is a normal occurrence whenever radio
signals are transmitted inside a building.
If you step away from the “drop out” zone,
the audio will return. If a drop out zone
is within the area of the stage or sound
board(s), it is possible to eliminate the drop
out zone by moving your EO3 transmitter as
little as 12-18 inches in any direction. After
you move the transmitter, “range walk” the
stage and other areas again to check for
consistent reception.
Note: A slight hum may be heard if the receiver
is used within six feet of the transmitter. This is
normal and does not affect performance.
eO3 receiver (Front Panel)
eO3 receiver (Top Panel)
2
4
3
5
1
Inserting EMI into
earphones
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EO3 Specifications
OVerall sYsTeM PerFOrManCe
Frequency response
signal-to-noise ratio
Total Harmonic Distortion
rF Carrier Frequencies
100 Hz - 10KHz 3 dB
60 dB
< 0.5%
Eight factory preset channels between 72-76 MHz
Channel AA: 72.1, BB: 72.3, CC: 72.5, DD: 72.7
EE: 72.9, FF: 75.5, GG: 75.7, HH: 75.9
Better than .005%
Frequency stability
Modulation
FM 75 KHz
Operating range
Up to 300 feet line-of-sight
eO3-T TransMITTer
line Input
Connector: One 1/4“ phone jack
Impedance: 100 K Ohms, unbalanced.
Connector: One 1/4“ phone jack
Mic Input
Impedance: low impedance, unbalanced, with 9 VDC at 1 mA
for condenser mic.
Power Output
Controls
Indicators
80,000 µV @ 3 meters
Power On/Off, audio input gain adjust
Power On LED, Audio Modulation “TX” LED
Permanently mounted telescoping whip
9 VDC regulated, @ 200 mA, AC-EO3 adapter provided
1.25” H, 8.25” W, 4.25” D (3.175 x 20.9 x 10.8 cm)
18.2 oz. (500 g.)
antenna
Power requirement
Dimensions
weight
eO3-r reCeIVer
Controls
Combination volume/on-off wheel
100 mW max into 16 Ohms
3.5 mm mini jack for earbuds output
Binaural EB-3 earbuds with optional-use EMI soft rubber inserts
Integral with earbud cord
audio Output
Connectors
earphones
antenna
Indicators
sensitivity
LED power on indicator
2 µV for 12 dB Sinad with squelch defeated
Squelches at 10 µV for min. 50 dB S-N ratio
8-10 µV
Mute Threshold
Power requirement
Battery life
Dimensions
weight
9V carbon zinc or alkaline battery
17-20 hours with alkaline battery; 10-12 hours with carbon zinc battery
3.35” H, 2.75” W, .75” D (8.5 x 6.5 x 2.25 cm)
2.65 oz. without battery (73 g)
Specifications subject to change at any time without prior notice for purposes of product improvement
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Information
In the u.s. If you are experiencing operational problems with your system, please refer to
service, please contact the Nady Service Department at (510) 652-2411 to obtain a Return
Authorization (R/A) Number and service quote (if out of warranty). Make sure the R/A
Number is clearly marked on the outside of the package that you are returning.
If your unit is out of warranty, please enclose a cashier’s check or money order (or pay
by credit card) per instructions by the Nady Service Department. Ship your unit prepaid
to: Nady Systems, Service Department, 6701 Shellmound Street, Emeryville, CA 94608.
Include a brief description of the problem you are experiencing. For service of a unit under
warranty, please follow the instructions in the following section.
Outside the u.s. For service or warranty matters please contact the Nady distributor in your
country through the dealer/store from which you purchased this product.
Do not attempt to service this unit yourself as
it can be dangerous and will also void the warranty.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
One-Year Limited Warranty
Nady Systems, Inc. warrants to the original consumer purchaser that the unit is free from any defects
in material or workmanship for a period of one year from the date of original retail purchase. If any such
defect is discovered within the warranty period, Nady Systems, Inc. will repair or replace the unit free of
charge, subject to verification of the defect or malfunction upon return to Nady Systems. Please do not
return your Nady product to the store where it was purchased as Nady Systems handles your warranty
service directly. Communication with our Service Department is the most efficient means of servicing
your unit and we are dedicated to keeping you a satisfied customer.
To the extent permitted by law, any applicable implied warranties, including warranties of merchantability
and fitness are hereby limited to one year from the date of purchase. Consequential or incidental
damages resulting from a breach of any applicable express or implied warranties are hereby excluded.
This warranty is in lieu of all other agreements and warranties, general or special, express or implied
and no representative or person including a Nady dealer, agent, or employee is authorized to assume
for us any other liability in connection with the sale or use of this Nady Systems’ product.
Whereas some states do not allow limitations on how long implied warranties last, and do not allow
exclusion of incidental or consequential damages, the above limitations and exclusions may not apply
to you. This warranty gives you specific legal rights and you may also have other rights which may vary
from state to state.
This warranty is subject to the following conditions:
1) This system must have been purchased from an authorized Nady dealer and all warranty
service must be performed by Nady’s service department. Any service not performed by Nady
will automatically void this warranty.
2) Items not covered: physical damage resulting from improper handling of the unit in transit from the
factory by the shipper (Nady Systems is not responsible for such damage and all such claims must be
made against the shipping company by the consignee); defects caused by normal wear of the product
(expendable parts are typically connectors, cables, potentiometers, switches and similar components);
damage or defects caused by abuse, neglect, accident, failure to connect or operate the unit in any way
that does not comply with applicable technical or safety regulations, or improper repair, excessive heat
or humidity, alteration or unreasonable use of the unit, causing cracks, broken cases/housings or parts;
damage caused by leaking batteries; finish or appearance items; items damaged in shipment en route to
Nady Systems, Inc. for repair. The warranty is null and void if any Nady serial number has been removed
or defaced.
How To Obtain service:
1) If factory service is required, please contact our Service Department at (510) 652-2411 for a return
authorization (R/A) number. Make sure the R/A number is clearly marked on the outside of your package.
(Please note: if an R/A number is not included, our Shipping Department cannot accept your package.)
2) Send the unit back to Nady Systems, 6701 Shellmound Street, Emeryville, CA, 94608, freight pre-paid.
You must include proof of date and place of purchase (i.e., photocopy of your bill of sale) or Nady cannot
be responsible for repair or replacement. Nady Systems, Inc. will not repair, nor be held responsible,
for any units returned without proper identification, return address, and R/A number clearly marked
on the package.
3) Per the above, Nady will perform all warranty service and return the unit to you at no charge.
Nady Systems will inform the buyer if product sent in does not meet the terms of this warranty
and will provide a quote for fixing the unit and/or shipping it back exclusively at the buyer’s expense.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
6701 Shellmound Street Emeryville, CA USA 94608
|
|
Download from Www.Somanuals.com. All Manuals Search And Download.
|