EXPRESS5800/120Lg
()
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
S e r v i c e G u i d e
Download from Www.Somanuals.com. All Manuals Search And Download.
Proprietary Notice and Liability Disclaimer
The information disclosed in this document, including all designs and related materials, is
the valuable property of NEC Solutions (America), Inc. and/or its licensors. NEC Solutions
(America), Inc. and/or its licensors, as appropriate, reserve all patent, copyright and other
proprietary rights to this document, including all design, manufacturing, reproduction, use,
and sales rights thereto, except to the extent said rights are expressly granted to others.
The NEC Solutions (America), Inc. product(s) discussed in this document are warranted in
accordance with the terms of the Warranty Statement accompanying each product.
However, actual performance of each product is dependent upon factors such as system
configuration, customer data, and operator control. Since implementation by customers of
each product may vary, the suitability of specific product configurations and applications
must be determined by the customer and is not warranted by NEC Solutions (America), Inc.
To allow for design and specification improvements, the information in this document is
subject to change at any time, without notice. Reproduction of this document or portions
thereof without prior written approval of NEC Solutions (America), Inc. is prohibited.
Trademarks
Windows 2000 is a registered trademark of Microsoft Corporation.
Intel is a registered trademark of Intel Corporation.
Xeon is a trademark of Intel Corporation.
All other product, brand, or trade names used in this publication are the trademarks or registered
trademarks of their respective trademark owners.
PN: 456-01673-000
April 2003
Copyright 2003
NEC Solutions (America), Inc
10850 Gold Center Drive, Suite 200,
Rancho Cordova, CA 95670
All Rights Reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Proprietary Notice
Using This Guide
Text Conventions .................................................................................................................. x
Related Documents .............................................................................................................. xi
Safety Notices ..................................................................................................................... xii
Safety Notices for Users Outside of the U.S.A. and Canada ........................................xiii
Care and Handling.............................................................................................................. xiv
1. System Overview
Overview............................................................................................................................ 1-2
System Features ................................................................................................................. 1-3
System Chassis Features .................................................................................................... 1-4
Front View .................................................................................................................... 1-4
Front View (Door Opened)........................................................................................... 1-5
Rear View ..................................................................................................................... 1-7
Internal View ................................................................................................................ 1-9
System Board Features................................................................................................ 1-10
Standard Features............................................................................................................. 1-12
Xeon™ Processors...................................................................................................... 1-13
System Memory.......................................................................................................... 1-13
PCI Riser Slots............................................................................................................ 1-13
Video Controller ......................................................................................................... 1-13
SCSI Controller........................................................................................................... 1-13
Network Controller ..................................................................................................... 1-13
Keyboard and Mouse .................................................................................................. 1-14
RJ-45 Serial Port......................................................................................................... 1-14
ACPI ........................................................................................................................... 1-14
System Board Management Controller (BMC) .......................................................... 1-15
Power Supplies................................................................................................................. 1-16
Peripheral Bays ................................................................................................................ 1-16
System Functions ............................................................................................................. 1-17
Degradation Feature.................................................................................................... 1-17
Remote Power-On Feature (Wake On LAN).............................................................. 1-17
AC-LINK Feature ....................................................................................................... 1-17
Security ............................................................................................................................ 1-18
Security with Mechanical Locks and Monitoring....................................................... 1-18
Software Locks via the System Setup Utility ............................................................. 1-18
2. Setting Up the System
Overview............................................................................................................................ 2-2
Selecting a Site................................................................................................................... 2-2
Unpacking the System........................................................................................................ 2-3
Making Connections .......................................................................................................... 2-3
Connecting the Power Cord ............................................................................................... 2-5
Using the System................................................................................................................ 2-5
Opening the Front Door of the Tower Cabinet............................................................. 2-6
Contents iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering On Your System............................................................................................2-7
Powering Off the Server System...................................................................................2-8
Forcing a Power Shutdown ...........................................................................................2-8
3. Configuring Your System
Configuring Your System...................................................................................................3-2
BIOS Setup Utility..............................................................................................................3-3
Using the BIOS Setup Utility........................................................................................3-3
BIOS Setup Configuration Settings...............................................................................3-4
Main Menu ....................................................................................................................3-5
Primary and Secondary Master and Slave IDE Submenus....................................3-6
Processor Settings Submenu..................................................................................3-6
Advanced Menu ............................................................................................................3-7
PCI Configuration Menu .......................................................................................3-8
Onboard NIC 1 / Onboard NIC 2 Submenu ..........................................................3-9
Onboard SCSI Submenu........................................................................................3-9
Onboard Video Submenu ......................................................................................3-9
Peripheral Configuration Submenu .......................................................................3-9
Memory Configuration Submenu........................................................................3-10
Advanced Chipset Control Submenu...................................................................3-10
Security Menu .............................................................................................................3-11
Server Menu ................................................................................................................3-12
System Management Submenu............................................................................3-13
Console Redirection Submenu ............................................................................3-14
Event Log Submenu ............................................................................................3-14
Boot Menu...................................................................................................................3-15
Boot Device Priority Submenu............................................................................3-15
Hard Drives Submenu .........................................................................................3-15
Removable Devices Submenu.............................................................................3-16
Exit Menu....................................................................................................................3-16
SCSISelect Utility.............................................................................................................3-17
Running the SCSISelect Utility...................................................................................3-17
Adaptec SCSI Utility Configuration Settings..............................................................3-18
SCSI Disk Utilities......................................................................................................3-19
Exiting Adaptec SCSI Utility......................................................................................3-20
Configuring the RAID Controller.....................................................................................3-21
Configuring System Board Jumpers.................................................................................3-22
Before You Begin........................................................................................................3-22
Moving System Board Jumpers ..................................................................................3-23
Clearing CMOS...........................................................................................................3-23
Clearing and Changing the Passwords ........................................................................3-24
4. Disassembly and Reassembly
General Information ...........................................................................................................4-3
Static Precautions ...............................................................................................................4-3
Equipment Log ...................................................................................................................4-3
Tools Recommended for Upgrading Your System.............................................................4-4
Preparing Your System for Disassembly and Reassembly.................................................4-4
Side Access Panel...............................................................................................................4-5
Processor Air Duct..............................................................................................................4-8
Removal.........................................................................................................................4-8
Installation.....................................................................................................................4-9
iv Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Modifying the System Board ........................................................................................... 4-10
Replacing the Real-time Clock Battery....................................................................... 4-10
Removing and Installing a Processor.......................................................................... 4-13
CPU Installation.................................................................................................. 4-14
CPU Removal...................................................................................................... 4-19
DIMMs........................................................................................................................ 4-20
Installing DIMMs................................................................................................ 4-21
Removing DIMMs .............................................................................................. 4-23
Hard Disk Drives.............................................................................................................. 4-25
Installation................................................................................................................... 4-25
Removal ...................................................................................................................... 4-28
Auto Rebuild Functionality......................................................................................... 4-29
Hot-Swap Power Supply.................................................................................................. 4-30
Installation................................................................................................................... 4-30
Removal ...................................................................................................................... 4-33
Non-Hot-Swap Power Supply.......................................................................................... 4-34
Removal ...................................................................................................................... 4-34
Front Cooling Fan Unit .................................................................................................... 4-35
Installation................................................................................................................... 4-35
Removal ...................................................................................................................... 4-37
Removable 5.25-inch Media Devices .............................................................................. 4-38
Installation................................................................................................................... 4-39
Removal ...................................................................................................................... 4-40
PCI Boards ....................................................................................................................... 4-41
Installation................................................................................................................... 4-42
Removal ...................................................................................................................... 4-44
RAID Controller Board.................................................................................................... 4-45
Using Internal Disks in Disk Array Configuration ..................................................... 4-47
Diskette Drive and Carrier Assembly .............................................................................. 4-48
Front Bezel and Front Bezel Hinge (Tower-Based System)............................................ 4-50
Front Panel ....................................................................................................................... 4-51
Hot-Swap HDD Bay......................................................................................................... 4-53
Hot-Swap SCSI Backplane .............................................................................................. 4-54
Replacing the Rear Cooling Fan ...................................................................................... 4-56
System Board ................................................................................................................... 4-58
Power Supply Back Board ............................................................................................... 4-60
Tower Feet ....................................................................................................................... 4-62
I/O Shield ......................................................................................................................... 4-63
LED/Switch Assembly..................................................................................................... 4-64
Intrusion Switch Assembly .............................................................................................. 4-65
5. Problem Solving
Problem Solving................................................................................................................. 5-2
Static Precautions............................................................................................................... 5-2
Resetting the Server ........................................................................................................... 5-3
Forced Shutdown ............................................................................................................... 5-4
Troubleshooting Checklists................................................................................................ 5-5
Initial System Startup.................................................................................................... 5-5
Running New Application Software............................................................................. 5-6
After System Has Been Running Correctly .................................................................. 5-7
Diagnostic Procedures........................................................................................................ 5-8
Error Checking.............................................................................................................. 5-8
Troubleshooting Guide ................................................................................................. 5-8
Contents v
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the System for Diagnosing Problems....................................................5-8
Monitoring POST ..................................................................................................5-9
Verifying Proper Operation of Key System Indicators .......................................5-10
Confirming Loading of the Operating System ....................................................5-10
Specific Problems and Corrective Actions.......................................................................5-11
Power LED Does Not Light ........................................................................................5-11
Incorrect or No Beep Code..........................................................................................5-11
No Characters Appear on Screen ................................................................................5-12
Characters are Distorted or Incorrect ..........................................................................5-12
System Cooling Fans Do Not Rotate...........................................................................5-12
Diskette Drive Activity LED Does Not Light.............................................................5-13
CD-ROM Drive Activity Light Does Not Light .........................................................5-13
Problems with Application Software...........................................................................5-13
Bootable CD-ROM Is Not Detected............................................................................5-14
Problems with the Network ..............................................................................................5-14
Plug and Play Installation Tips.........................................................................................5-14
Error Messages .................................................................................................................5-15
POST Error Codes and Messages................................................................................5-15
POST Error Code Hardware References.....................................................................5-20
Beep Codes..................................................................................................................5-21
How to Identify BIOS and BMC Revision Levels ...........................................................5-22
Lamps ...............................................................................................................................5-23
LAN ACCESS Lamp ..................................................................................................5-23
STATUS Lamp............................................................................................................5-23
POWER/SLEEP Lamp................................................................................................5-25
DISK ACCESS Lamp .................................................................................................5-25
Access Lamps..............................................................................................................5-25
Hard Disk Drive Lamp................................................................................................5-26
Power Supply Lamps...................................................................................................5-27
DC Power Lamp..........................................................................................................5-27
Power Status Lamp......................................................................................................5-27
AC Power Lamp..........................................................................................................5-27
LAN Connector Lamps ...............................................................................................5-28
6. Illustrated Parts Breakdown
Exploded View ...................................................................................................................6-2
Field Replaceable Units......................................................................................................6-3
Pentium Processors........................................................................................................6-5
Replaceable Parts...................................................................................................6-5
Hard Disk Drives...........................................................................................................6-5
Replaceable Parts...................................................................................................6-5
DVD Drives...................................................................................................................6-5
Replaceable Parts...................................................................................................6-5
DAT Tape Drives..........................................................................................................6-5
Replaceable Parts...................................................................................................6-5
RAID Controllers and Cache ........................................................................................6-6
Replaceable Parts...................................................................................................6-6
SCSI Controllers............................................................................................................6-6
Replaceable Parts...................................................................................................6-6
Network Controllers......................................................................................................6-6
Replaceable Parts...................................................................................................6-6
Memory Expansion .......................................................................................................6-6
Replaceable Parts...................................................................................................6-6
vi Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable List...................................................................................................................... 6-7
A. Specifications
System Specifications ....................................................................................................... A-2
B. Installing and Configuring Windows® 2000
Overview........................................................................................................................... B-2
Device Drivers .................................................................................................................. B-2
Installation Assumption .................................................................................................... B-3
Installation Preparation ..................................................................................................... B-4
Installing Microsoft Windows® 2000 Operating System.................................................. B-5
Installation Notes ......................................................................................................... B-5
Windows 2000 Installation .......................................................................................... B-5
Installing LAN Adapters................................................................................................... B-7
Driver Installation for the Intel PRO/100+ LAN Adapter ........................................... B-7
Setting Network Driver Details.................................................................................... B-7
Driver Installation for the ATI RAGE XL Display Adapter............................................. B-8
C. IRQ and I/O Port Addresses
Interrupt Requests ............................................................................................................. C-2
PIRQ and PCI Device ....................................................................................................... C-2
I/O Port Address .......................................................................................................... C-3
D. Internal Cabling Diagrams
Standard Configuration ..................................................................................................... D-2
Disk Array Configuration of Built-in Hard Disks............................................................. D-3
Installing a SCSI File Device............................................................................................ D-4
Glossary
Equipment Log
INDEX
Contents vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using This Guide
Welcome to the EXPRESS5800/120Lg Service Guide. This service guide has all the
information found in the System User’s Guide, including disassembly and reassembly
instructions for all field replaceable units (FRUs). This service guide also contains technical
specifications, and a complete parts list, including an exploded view of the system.
If you have any comments regarding this service guide or if you think something needs to
be changed, please contact us. Limit your comments to issues concerning the
documentation only, and indicate which service guide you are referring to. For all other
service related issues, use your normal feedback channels.
This guide contains the following information:
! Chapter 1, “System Overview” provides an overview of your system and describes your
system’s major system components. See this chapter to familiarize yourself with the
features of your system.
! Chapter 2, “Setting Up Your System” tells you how to select a site, unpack the system,
install the system, make cable connections, and power on your system. This chapter also
familiarizes you with your system’s controls and indicators.
! Chapter 3, “Configuring Your System” tells you how to configure the system and
provides instructions for running the BIOS Setup Utility. This chapter also provides
information on system board jumper settings.
! Chapter 4, “Disassembly and Reassembly” provides you with instructions for upgrading
your system with an additional processor, optional memory, options cards, and
peripheral devices. This chapter also provides the disassembly and reassembly
instructions for all field replaceable units (FRUs).
! Chapter 5, “Problem Solving” contains helpful information for solving problems that
might occur with your system.
! Appendix A, “Specifications” includes hardware information about your system.
! Appendix B, “Installing and Configuring Windows 2000® ” contains instructions to
install and configure hardware and software used with the Microsoft Windows 2000
Operating System.
! Appendix C, “IRQ and I/O Port Addresses” lists the factory-set interrupt requests (IRQs)
and I/O Port addresses.
! Appendix D, “Internal Cabling Diagrams” includes system standard configuration and
RAID cabling information.
! “Glossary” defines the standard acronyms and technical terms used in this manual.
! “Equipment Log” provides you with a sample equipment log for documenting the
system configuration and future updates you may make to your system.
Using This Guide ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Text Conventions
This guide uses the following text conventions.
Warnings, cautions, and notes have the following meanings:
!
WARNING
Warnings alert you to situations that could result in serious personal injury or loss
of life.
!
CAUTION
Cautions indicate situations that can damage the system hardware or software.
Note: Notes give important information about the material being described.
! Names of keyboard keys are printed as they appear on the keyboard. For example, Ctrl,
Alt, or Enter.
! Text or keystrokes that you enter appear as boldface type. For example, type abc123 and
press ENTER.
! File names are printed in uppercase letters. For example, AUTOEXEC.BAT.
x Using This Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Documents
In addition to this guide, the following system documentation is included with your server
either as electronic files on EXPRESSBUILDER or as paper copy shipped with your server.
! System Release Notes
Release Notes provide you with the latest information about your system. This
information was not available to be included in your user's guide at the time it was
developed and released.
! Getting Started Sheet
The Getting Started Sheet provides several easy-to-follow steps to become familiar with
your server documentation and to complete your installation successfully.
Using This Guide xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Notices
!
! Caution: To reduce the risk of electric shock which could cause personal injury, follow
all safety notices. The symbols shown are used in your documentation and on your
equipment to indicate safety hazards.
! Warning: Lithium batteries can be dangerous. Improper handling of lithium batteries
may result in an explosion. Dispose of lithium batteries as required by local ordinance or
as normal waste if no local ordinance exists.
! Warning: The detachable power supply cord is intended to serve as the disconnect
device.
! Warning: This equipment has a 3-wire, grounded power cord. To prevent electrical
hazards, do not remove or defeat the ground prong on the power cord. Replace the
power cord if it gets damaged. Contact your dealer for an exact replacement.
! Warning: The DC push-button on/off switch on the front panel does not turn off the
system AC power. Also, +5vdc is present on the system board whenever the AC power
cord is connected between the system and an AC outlet. Before doing the procedures in
this manual, make sure that your system is powered off and unplug the AC power cord
from the back of the chassis. Failure to disconnect power before opening your system
can result in personal injury and equipment damage.
In the U.S.A. and Canada, the power cord must be a UL-listed detachable power cord (in
Canada, CSA-certified), type ST or SJT, 16 AWG, 3-conductor, provided with a molded-on
NEMA type 5-15 P plug cap at one end and a molded-on cord connector body at the other
end. The cord length must not exceed 9 feet (2.7 meters).
Outside the U.S.A. and Canada, the plug must be rated for 250 VAC, 10 amp minimum,
and must display an international agency approval marking. The cord must be suitable for
use in the end-user country. Consult your dealer or the local electrical authorities if you are
unsure of the type of power cord to use in your country. The voltage change occurs via a
switch in the power supply.
! Warning: Under no circumstances should the user attempt to disassemble the power
supply. The power supply has no user-replaceable parts. Inside the power supply are
hazardous voltages that can cause serious personal injury. A defective power supply
must be returned to your dealer.
xii Using This Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Notices for Users Outside of the U.S.A. and Canada
! PELV (Protected Extra-Low Voltage) Integrity: To ensure the extra-low voltage
integrity of the equipment, connect only equipment with mains-protected electrically-
compatible circuits to the external ports.
! Remote Earths: To prevent electrical shock, connect all local (individual office)
computers and computer support equipment to the same electrical circuit of the building
wiring. If you are unsure, check the building wiring to avoid remote earth conditions.
! Earth Bonding: For safe operation, only connect the equipment to a building supply
that is in accordance with current wiring regulations in your country. In the U.K., those
regulations are the IEE.
Using This Guide xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Handling
Use the following guidelines to properly handle and care for your system.
Protect the system from extremely low or high temperatures. Let
the system warm (or cool) to room temperature before using it.
Keep the system away from magnetic forces.
Keep the system dry. Do not wash the system with a wet cloth or
pour fluid into it.
Protect the system from being bumped or dropped.
Check the system for condensation. If condensation exists, allow it
to evaporate before powering on the system.
Keep the system away from dust, sand, and dirt.
xiv Using This Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
1
System Overview
! Overview
! System Features
! System Chassis Features
! Standard Features
! Power Supplies
! Peripheral Bays
! System Functions
! Security
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
Your server is a modular, multiprocessing server based on the Intel® Xeon
microprocessor family. It is a solid performer and offers the latest technology. The
combination of compute performance, memory capacity, and integrated I/O provides a
high performance environment for many server market applications. These range from
large corporations supporting remote offices to small companies looking to obtain basic
connectivity capability such a file and print services, e-mail, web access, web site
server, etc.
This server is conveniently housed and available as a tower-based system
(see Figure 1-1) or as a rack-mount system (fits into a standard EIA 19-inch rack
assembly).
Figure 1-1 Tower System Front View
Your server may include hot-swap SCSI hard disk drive bays. The hot-swap SCSI hard
disk drive bays hold up to six 1.0-inch SCSI hard disk drives that can be swapped in or
out of the system without powering it down, if RAID is configured in the system.
As application requirements increase, you can expand your server with an additional
processor, additional memory, add-in boards and peripheral devices; tape devices, CD-
ROM, and hard disk drives.
1-2 System Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
System Features
Your system features the following major components:
! Single or dual high-performance Intel™ Xeon™ 1.80GHz or 2.66GHz
processors.
! 256 MB to 4 GB of ECC SDRAM two way interleaved memory, using up to four
DIMMs.
! Six PCI expansion slots for add-in boards (four 64-bit/100MHz PCI slots and
two 32-bit/33MHz PCI slots).
! A maximum of six hot-swap SCSI hard disk drive bays accessible from the front
of the chassis.
! Hot-swap SCSI disk drive backplane; a failed drive can be removed and replaced
with a new drive without system power being turned off (if an optional
Redundant Array of Independent Disks (RAID) controller is installed.)
! High degree of SCSI disk fault tolerance and advanced disk array management
features through the use of RAID technology, if an optional RAID controller is
installed.
! Embedded PC-compatible support (serial, parallel, mouse, keyboard, diskette,
USB, LAN, and video).
! Integrated onboard ATI RAGE XL Video Graphics Array (VGA) controller with
8MB of video memory (VRAM).
! Adaptec SCSI controller providing Ultra-320/160 SCSI interfaces.
! Integrated Network Interface Controller (NIC), a dual channel Gigabit Ethernet
LAN controller supporting 10Base-T/100Base-TX/1000Base-T network systems.
! Dual channel enhanced IDE controller.
! Four slot, 5.25-inch removable media device bay.
! IDE CD-ROM drive and 3 ½-inch diskette drive.
! Three integrated Universal Serial Bus (USB) ports, one located at the front panel
and two located at the rear panel.
! Hardware monitors (temperature, fans, and voltage) and software monitors to
indicate failures.
! Chassis that supports up to two power supply modules. The additional power
supply is needed to provide hot-swappable redundant power (i.e., the system will
continue to operate with a single power supply failure). With two power modules
installed, one power module can be easily removed or installed from the back of
the chassis without turning the system power off.
! Fully lockable front bezel including Server Management software that monitors
the front bezel intrusion switch.
System Overview 1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
System Chassis Features
Figure 1-2 shows the system front view features seen with the front door closed.
Front View
1
2
1
2
4
5
6
7
3
1
Front door
Open this door to access the POWER switch, 5.25-inch devices, the CD-ROM drive, or the
floppy disk drive, or to install/remove hard disks to 3.5-inch bays. You can lock the front door
using the provided security key.
2
3
4
Key lock
When locked, secures the front door not allowing access to the front system controls.
Stabilizers (4)
Use the stabilizers to prevent the server from falling down.
LAN ACCESS lamp (green)
Lights in green while the server is connected to the network. Blinking in green indicates the
network activity. Numbers printed near the lamps indicate the LAN port number.
DISK ACCESS lamp (green/amber)
Lights in green while the internal hard disk is in access. When any one of the internal hard
disks fails, this lamp lights in amber.
POWER/SLEEP lamp (green)
Lights in green when the server is powered on. Off when the server is powered off. Blinks
when the system is placed in the sleep mode.
5
6
7
STATUS lamp (green/amber)
Lights in green while the server is in successful operation. When any error is detected, this
lamp lights in amber.
Figure 1-2. Front View (Door closed)
1-4 System Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Front View (Door Opened)
Figure 1-3 shows the system front view features seen with the front door opened.
7
1
2
1
2
8
9
10
8
6
5
4
3
5-1
2-1 2-2 2-3
2-4
2-5
2-6
5-2
5-3
CD-ROM Drive
Floppy Disk Drive
Figure 1-3. Front View (Door opened)
System Overview 1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
5.25-inch device bay
Backup tape drives may be installed in the 5.25-inch device bay.
CD-ROM drive
The CD-ROM drive reads data from the inserted CD-ROM.
2-1 Headphone jack
2-2 Volume control
2-3 Access lamp (lights in amber while being accessed)
2-4 CD-ROM slot
2-5 Emergency hole
2-6 Open/Close button
3
4
Disk lamp (green/amber)
The disk lamp is lit green if a hard disk installed in the server is accessed. If a hard disk is
defected, the lamp is lit amber. During the rebuild processing, the lamp is lit green or amber
alternately. (This occurs only in the disk array configuration.)
3.5-inch hard disk drive bay
The 3.5-inch hard disk drive bay contains up to six hard disks. Hard disks having the
thickness of 1 inch can be inserted into the slots.
The SCSI IDs are defined as follows:
ID0 to ID5 from bottom to top.
5
3.5-inch floppy disk drive
Insert a 3.5-inch floppy disk to the 3.5-inch floppy disk drive to read data from the disk or write
data to the disk.
5-1: Eject button
5-2: Disk inserting section
5-3: Floppy disk access lamp (lit green during accessing)
6
7
Cover open sensor
The cover open sensor detects the open of the front door.
Power switch
The power switch is used to turn on/off the power. If you press the switch once, then the
POWER/SLEEP lamp goes on and the power is turned on. If you press the switch again, the
power is turned off. The system is forcibly shut down when the power switch is pressed
continuously for four seconds or longer.
8
9
Lamps (see the figure on the previous page)
Reset switch
The reset switch is used to reset the server.
10 Dump switch (NMI switch)
Non-maskable Interrupt switch.
The dump switch is used to collect the event logs having occurred in the server.
Figure 1-3. Front View (Door opened)
1-6 System Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear View
Figure 1-4 shows the system rear view features.
10
9
1
2
3
4
5
11
12
6
13
14
15
7
16-1
17-1
15
16-2
17-2
8
System Overview 1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Power supply
The power unit supplies DC powers to the server.
2
3
AC inlet
The AC inlet is connected with the power cord.
DC power lamp
The AC power lamp blinks green if the power supply receives the AC power through the power
cord. The lamp goes on green when the power of the server is turned on.
4
5
Power status lamp
The lamp goes on if the power is defected.
AC power lamp
If the power cord is plugged to the AC inlet to supply AC power to the power supply unit, this
lamp goes on.
6
7
Additional power supply slot
An optional power supply may be installed on the slot.
Serial port B connector
The serial port B connector is used to connect the server to a device with the serial interface.
The server cannot be directly connected to a leased line through the connector.
8
9
Additional PCI board slots
Optional PCI boards may be inserted into the slots.
Mouse connector
The mouse connector is connected with the mouse coming with the server.
10 USB-1 - USB-3 connectors
The USB-1 to USB-3 connectors are connected with devices accepting the USB interface.
Connector 1 to connector 3 are assigned from right to left.
11 Keyboard connector
The keyboard connector is connected with keyboard coming with the server.
12 Serial port A connector
The serial port A connector is connected with a device having the serial interface.
13 Printer port connector
The printer port connector is connected with a printer with the Centronics interface.
14 Monitor connector
The monitor connector is connected with the display unit.
15 Link/ACT lamp
The Link/ACT lamp shows the LAN access status.
16 LAN connector
The LAN connector is connected with a network system on LAN. The value following the bold-
faced number indicates the port number.
16-1 LAN2 supports 1000BASE-T/100BASE-TX/10BASE-T network subsystem.
16-2 LAN1 supports 100BASE-TX/10BASE-T network subsystem.
17 Speed lamp
Indicates the LAN transfer rate.
17-1 1000/100/10 lamp
17-2 100/10 lamp
Figure 1-4. Rear View
1-8 System Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Internal View
Figure 1-5 shows an internal view of your system with the air duct covers removed.
1
2
3
4
5
11
6
10
9
8
7
1
2
3
Power supply
DIMMs (factory-installed in slots #1A and #1B.)
CPU1 (factory-installed)
4
5
CPU2
5.25-inch device bays (4 slots)
A standard CD-ROM drive is installed in slot #3. The device bay can include a maximum of
two optional file devices.
6
7
3.5-inch floppy disk drive
3.5-inch hard disk drive bay
The hard disk drive bay can hold up to six 1.0-inch SCSI hard disk drives.
8
9
Cooling fan (Fan 5: option)
Cooling fan (Fan 3: option)
10 Mother board
11 Cooling fan (Fan 1)
Figure 1-5. Internal View
System Overview 1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
System Board Features
Figure 1-6 shows details of the system board.
1
2
3
4
5
26
6
7
8
25
24
9
10
11
12
23
13
14
15
22
21
20
19
18
17 16
1-10 System Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Power signal connector
Power connector
3
DIMM sockets (slots #1A, #1B, #2A, and #2B from top to bottom)
CPU1 socket
4
5
CPU2 socket
6
Floppy disk drive connector
Cooling fan connector (Fan 5)
Cooling fan connector (not used)
Power connector
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
HSBP (B) connector (not used)
HSBP (A) connector (not used)
USB connector
IDE connector (for CD-ROM drive)
Cooling fan connector (not used)
Cooling fan connector (Fan 3: option)
Front panel interface connector
IDE connector (not used)
Jumper switch for clearing CMOS/password
Lithium battery
Ultra320 (A) connector (for built-in hard disk)
DAC LED connector
Serial (COM B) connector
PCI board slots
(slots PCI #1, PCI #2, PCI #3, PCI #4, PCI #5, and PCI #6 arranged from top to bottom)
PCI #1 to #4: 64-bit/100 MHz
PCI #5, #6:
32-bit/33 MHz
24
25
26
Cooling fan connector (Fan 1)
Cooling fan connector (Fan 2: option)
External connection connector
Figure 1-6. System Board
System Overview 1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Features
High performance
Expandability
! Wide variety of optional I/O slots
Four 64-bit, 100 MHz PCI slots
Two 32-bit, 33 MHz PCI slots
! Large memory of up to 4 GB
! Six SCSI hard disk drive bays (hot-
swappable)
! Remote power-on feature
! Up to two Intel Xeon processors
! Two power supplies (Redundancy)
! USB interface (A USB-support driver is
required.)
! Intel Xeon Processor
N8100-865F: 1.8GHz
N8100-866F: 2.66GHz
! High-speed 1000BASE-T/100BASE-TX/
10BASE-T interface
(1000Mbps/100Mbps/10Mbps supported)
! High-speed disk access
(Ultra320 SCSI)
! Convert to rack-mount type (N8143-56F
Rack Conversion Kit is required.)
High-reliability
Many Available Features
! Memory monitoring feature (single-bit
error correction/double-bit error detection)
! CPU/memory/cooling fan degradation
feature (logical isolation of a failed device)
! Bus parity error detection
! Graphic accelerator "RAGE XL" support
! El Torito Bootable CD-ROM (no emulation
mode) format support
! POWER switch mask
! Software power-off
! Temperature detection
! Error notification
! Remote power-on feature
! AC-LINK feature
! Internal CPU fan monitoring feature
! Internal voltage monitoring feature
! BIOS password feature
! Security feature (security lock)
! Redundant power supplies (1+1)
! Intelligent Platform Management Interface
(IPMI)
! Baseboard Management Controller (BMC)
! Remote console feature
Self-diagnosis
! Power On Self-Test (POST)
! Test and Diagnosis
Management Utilities
Maintenance Features
! ESMPRO
! Management Workstation Application
! Off-line Maintenance Utility
! Memory dump feature using the DUMP
(NMI) switch
( MWA)
Power Saving Feature
Easy and Fine Setup
! Sleep feature
! EXPRESSBUILDER (system setup utility)
! SETUP (BIOS setup utility)
(available for Windows 2000)
! SCSISelect (SCSI device utility)
! Configuration Diskette Creator
1-12 System Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Xeon™ Processors
Depending on system configuration, each system includes one or two Intel Xeon
1.80GHz or 2.66GHz processors. Each processor plugs into a INT3/FCPGA socket
package. The processor includes a 512K cache. When two processors are installed, both
processors must be of identical bus and core speed.
The processor external interface operates at a maximum of 400MHz. The second-level
cache is located on the substrate of the processor cartridge. The cache includes burst
pipelined synchronous static RAM (BSRAM).
System Memory
The system board contains four 168-pin DIMM sockets. Memory is partitioned as two
banks of registered SDRAM DIMMs (DDR200 compatible) that must be populated in
pairs, each providing 72 bits of buffered two-way interleaved memory (64-bit main
memory plus ECC). Your system may include from 256 MB to 4 GB of memory, using
up to four DIMMs.
System memory begins at address 0 and is continuous (flat addressing) up to the
maximum amount of DRAM installed (exception: system memory is noncontiguous in
the ranges defined as memory holes using configuration registers). The system
supports both base (conventional) and extended memory.
PCI Riser Slots
The server's expansion capabilities meet the needs of file and application servers for
high performance I/O by providing PCI expansion slots.
The system board has four full-length, full height 64-bit/100MHz PCI slots and two 32-
bit/33MHz PCI slots.
Video Controller
The system board uses an ATI RAGE XL PCI graphics accelerator with 8 MB of video
SDRAM. The embedded SVGA video subsystem supports:
! Resolutions up to 1600 x 1200 under 2D and 1024 x 768 under 3D
! CRT and LCD monitors up to 100 Hz vertical refresh rate.
The system board supports disabling of the onboard video through the BIOS setup
menu or when a plug in video card is installed in any of the PCI slots.
SCSI Controller
The system board includes an embedded Adaptec AIC7901W SCSI controller. The
AIC7901W provides Ultra-320/160 SCSI functions. As implemented on the system
board, the interface attaches to an Ultra-320/160 SCSI backplane that supports up to six
Ultra-320/160 SCA drives.
Network Controller
The system board uses a dual-channel Ethernet Controller and supports 10Base-
T/100Base-TX/1000Base-T network subsystems.
System Overview 1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
The Network controller supports the following features:
! 64-bit, 100 MHz PCI-X interface
! Integrated IEEE 802.3 10Base-T, 100Base-TX, and 1000Base-T compatible
PHY
! IEEE 820.3u auto-negotiation support
! Chained memory structure similar to the 82557, 82558, 82559 and 82596
! Full duplex support at 10 Mbps, 100 Mbps, and 1000 Mbps operation
! Low power +3.3 V devices.
On the system board, NIC1 can be used as both a network interface and server
management interface.
Keyboard and Mouse
The keyboard/mouse controller is PS/2-compatible.
RJ-45 Serial Port
The rear RJ-45 serial port is a fully functional serial port that supports any standard
serial device and provides support for serial concentrators. For server applications that
use a serial concentrator to access the server management features of the mother board,
a standard 8-pin CAT-5 cable from the serial concentrator is plugged directly into the
rear RJ-45 serial port. The 8 pins of the RJ-45 connector can be configured to match
either of two pin-out standards used by serial port devices.
To accommodate either standard, the J5A2 jumper block located directly behind the
rear RJ-45 serial port must be jumpered appropriately according to the desired standard.
ACPI
An Advanced Configuration and Power Interface (ACPI) aware operating system can
place the system into a state where the hard drives spin down, the system fans stop, and
all processing is halted. However, in this state the power supply is still on and the
processors are still dissipating some power such that the power supply fan and
processor fans are still running.
Note: ACPI requires an operating system that supports its
feature.
!
CAUTION
Only when the AC power is disconnected is the system completely
off.
The sleep states are defined as follows:
! s0: Normal running state.
1-14 System Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
! s1: Processor sleep state.
No context will be lost in this state and the processor caches will maintain
coherency.
! s4: Hibernate or Save to Disk.
The memory and machine state are saved to disk. Pressing the power button or
other wakeup event restores the system state from the disk and resumes normal
operation. This assumes that no hardware changes have been made to the system
while it was off.
! s5: Soft off.
Only the RTC section of the chipset and the BMC are running in this state.
System Board Management Controller (BMC)
Server management is concentrated in the System Board Management Controller
(BMC). The BMC and associated circuitry are powered from a 5Vdc standby voltage,
which remains active when system power is switched off, but the ac power source is
still on and connected.
The BMC supports the Management Workstation Application (MWA), which allows
remote server management via a modem or direct connection to a manager system.
Events monitored by the manager system include over-temperature and over-voltage
conditions, fan failure, or chassis intrusion.
Information on the Management Workstation Application (MWA) may be found in
Appendix B of this User’s Guide.
One major function of the BMC is to autonomously monitor system management
events, and log their occurrence in the nonvolatile System Event Log (SEL). The events
being monitored include overtemperature and overvoltage conditions, fan failure, or
chassis intrusion. To enable accurate monitoring, the BMC maintains the nonvolatile
Sensor Data Records (SDRs), from which sensor information can be retrieved. The
BMC provides an ISA host interface to SDR sensor information, so that software
running on the server can poll and retrieve the server's current status.
The BMC performs the following:
! Monitors server board temperature and voltage
! Monitors processor presence and controls Fault Resilient Boot (FRB)
! Detects and indicates baseboard fan failure
! Manages the SEL interface
! Manages the SDR Repository interface
! Monitors the SDR/SEL timestamp clock
! Monitors the system management watchdog timer
! Monitors the periodic SMI timer
! Monitors the event receiver
System Overview 1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
! Controls secure mode, including video blanking, diskette write-protect
monitoring, and front panel lock/unlock initiation
! Controls Wake On LAN via Magic Packet support.
Power Supplies
The system contains one auto-sensing 450-watt power supply at an operating frequency
of 50/60 Hz.
A second optional power supply may be added as part of a fault-tolerant hot-swap
design. With two power supplies installed, in the unlikely event of a power supply
failure, the load is transferred to the remaining power supply without interruption to
normal operation. In this case the faulty power supply can be replaced without
powering down the system.
NOTE: The power supplies are not hot-swappable unless there are two power
supplies installed.
The power supplies are designed to comply with existing emission standards and
provide sufficient power for a fully loaded system configuration.
Peripheral Bays
The system supports a variety of standard PC AT-compatible peripheral devices. The
chassis includes these peripheral bays:
! A 3.5-inch front panel bay for installing the standard 3.5-inch floppy disk drive
(supports 720KB and 1.44MB floppy disk media)
! Four 5.25-inch device bays for installing half-height or full-height 5.25-inch
peripheral devices such as an optional tape drives.
! The SCSI hard disk drive bays for installing up to six SCSI hard disk drives.
The SCSI disk drives can be easily installed or removed. The drive carrier allows you
to access to disk drives from the front of the system. If disk drives are provided with
RAID configuration within the system, a disk drive can be swapped with another
without power interruption in the system (hot-swap).
NOTE: The SCSI hard disk drive bays contain a hot-swap back plane that
require an 80-pin single connector attachment (SCA) connector on the drives that
you install.
1-16 System Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
System Functions
The following subsections describe select system functions.
Degradation Feature
The degradation feature automatically isolates a failed DIMM or processor to assure
continuous operation of the server when the POST (Power On Self-Test, self-diagnosis
program after power on) detects such a DIMM or processor.
Failed DIMMs and processors may be identified on the screen that the POST displays,
or with the BIOS setup utility, "SETUP." They may also be identified on the system
that has the ESMPRO installed.
Remote Power-On Feature (Wake On LAN)
The remote power-on function turns on the server through a network. It sends a special
packet from the management computer to a remote server to turn it on if the server is
off-powered.
To enable this feature, you must select "Enabled" for "Wake on LAN" in the Advanced
Chipset Control of the Advanced menu of the BIOS setup utility, "SETUP." (See
Chapter 4.)
The remote power-on feature is not available in the following cases. Press the POWER
switch once to start the OS, and turn off the server in an appropriate procedure.
! Abnormal previous system shut-down
! No power supply to the server (due to turned-off breaker, disconnected power
cord, power blackout, etc.)
AC-LINK Feature
When the power cord of the server is connected to an uninterruptible power supply
(UPS) unit, the server supports the power linkage feature that enables control over the
power supply from the UPS to the server. The AC-LINK feature can be enabled or
disabled with the Server menu of the BIOS setup utility, "SETUP." (See Chapter 4.)
System Overview 1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Security
To help prevent unauthorized entry or use of the system, the system includes a full
lockable front panel and Server Management software that monitors the system
intrusion switches.
Security with Mechanical Locks and Monitoring
The front door of the server contains a mechanical lock to prevent access to the front of
the computer chassis.
The computer chassis includes an intrusion switch for the front cover and
intrusion/interlock switches for the left side cover (as viewed from the front). When
any these covers are opened, the switch transmits an alarm signal to the system board,
where server management software processes the signal. The side cover switch also
operates as interlock switch.
Software Locks via the System Setup Utility
The BIOS SETUP Utility provides a number of security features to prevent
unauthorized or accidental access to the system. Once the security measures are
enabled, access to the system is allowed only after the user enters the correct
password(s). For example:
! Enable the keyboard lockout timer so that the server requires a password to
reactivate the keyboard and mouse after a specified time-out period – 2 to 120
minutes.
! Set and enable an administrative password.
! Set and enable a user password
! Set secure mode to prevent keyboard or mouse input and to prevent use of the
front panel reset and power switches.
! Activate a hot-key combination to enter secure mode quickly.
! Disable writing to the floppy disk drive when secure mode is set.
1-18 System Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Setting Up the System
! Overview
! Selecting a Site
! Unpacking the System
! Making Connections
! Connecting the Power Cord
! Using the System
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
This chapter describes how to select a site, unpack the system, make cable
connections, and power on the system units. Information on front and rear panel
features, switches and LEDs are also included in this chapter.
Selecting a Site
The system operates reliably in a typical office environment.
Choose a site that is:
! Near grounded, three-pronged power outlets.
Note: For the United States and Canada, this means a
NEMA 5-15R outlets for 100-120 VAC or NEMA 6-15R
outlets for 200-240 VAC. For other international sites, this
means three-pronged power outlets applicable for the
electrical code of the region.
!
WARNING
Be sure the power service connection is through a properly
grounded outlet.
!
CAUTION
When two power supplies are installed in the system the
power plug from each of the power supplies must be
plugged into the same common ground power outlets.
! Clean, dust-free, and well ventilated. Front and rear ventilating openings
kept free of obstructions. Away from sources of heat, vibration or
physical shock.
! Isolated from strong electromagnetic fields and electrical noise produced
by electrical devices (such as air conditioners, large fans, large electric
motors, radio and TV transmitters, and high-frequency security devices)
! Spacious enough to provide at least ten inches (25 centimeters) in front of
the system, five inches (13 centimeters) behind the system and three
inches (eight centimeters) on each side of the system for proper cooling,
airflow, and cable clearance.
! Easily accessible for system maintenance and installation of system
upgrades.
2-2 Setting Up the System
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking the System
!
WARNING
The non-hot-swap system can weigh up to 40 pounds
(18 kg) and the hot-swap system can weigh up to 77 pounds
(35 kg). If the system contains numerous optional boards
and peripheral devices, it will weigh more. To avoid personal
injury, make sure you have someone help you lift or move
the system.
When you receive your system, inspect the shipping containers prior to
unpacking. If the shipping boxes are damaged, note the damage, and if possible,
photograph it for reference. After removing the contents of the containers, keep
the cartons and the packing materials. If the contents appear damaged when you
unpack the boxes, file a damage claim with the carrier immediately.
Making Connections
If your system normally operates without a video display or keyboard (for
example, as a network server), you must install a video display and keyboard to
configure the system. You may remove them after running the BIOS Setup
Utility. For information on running the BIOS Setup Utility, refer to Chapter 3
"Configuring Your System" of this User’s Guide.
Refer to the previous figure (Rear Features and Controls) and connect your
keyboard, monitor, and mouse. Connect any external peripheral devices such as
a printer or modem by following the instructions included with these devices.
!
CAUTION
Damage to the system may result if the keyboard/mouse
cable is inserted or removed when power is applied to the
system.
Inserting a telephone line connector into a RJ-45 LAN port
may result in personal injury and equipment damage.
The server is provided with connectors for wide variety of peripheral devices on
its front and rear. Figure 2-1 illustrates available peripheral devices for the
server in the standard configuration and locations of the connectors for the
devices.
!
CAUTION
Power off the server and peripheral device before
connection. Connecting a powered peripheral device to the
powered server may cause malfunctions and failures.
Setting Up the System 2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
! Before connecting a third-party peripheral device or interface cable to the
server, consult with your sales agent. Some third-party devices may not
be used with the server.
! The total length of a cable (including the connection cable within a SCSI
device) is limited by the SCSI standard. Ask your service representative
for details. (The internal SCSI cable of the server is 0.1 m long.)
! The LAN connector and the serial port 2 connector of this server have the
same shape. Be careful not to connect a cable to the wrong connector.
Tag all LAN and serial port cables.
A leased line cannot be connected directly to the serial port connectors.
Device with the USB interface
(e.g., terminal adapter)
Connect appropriate
power source.
Mouse
3
Keyboard
Device with the serial interface (e.g.,
modem)
Direct connection to
the private telephone
line is prohibited.
Display unit
Hub
(multiport repeater)
REAR
Printer with the
parallel interface
Device with the serial interface (e.g., modem)
Direct connection to the private telephone line
is prohibited.
Figure 2-1. Making Connections
2-4 Setting Up the System
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Power Cord
Plug the female end of each AC power cord shipped with your system into the
input receptacle on the rear of each power supply shipped with your system.
Plug the male end of the power cord into NEMA 5-15R outlet for 100-120 VAC
or NEMA 6-15R outlet for 200-240 VAC.
If a power cord supplied with the system is not compatible with the AC wall
outlet in your region, obtain a suitable power cord that meets the following
criteria.
! The power cord must be rated for the available AC voltage and have a
current rating that is at least 125% of the current rating of the system.
! The power cord connector that plugs into the wall outlet must be
terminated in a grounding-type male plug designed for use in your region.
It must have certification marks showing certification by an agency
acceptable in your region.
! The power cord connector that plugs into the system must be an
IEC- type CEE-22 female connector.
! The power cord must be less than 1.8 meters (6.0 feet) long.
When connecting the power cord to a power control unit such as an UPS unit,
confirm that the power control unit is powered OFF. Connecting the power cord
while power is supplied to the power control unit may cause a failure.
!
WARNING
A power cord is provided for each power supply shipped with
your system. Do not attempt to modify or use the supplied
AC power cord if it is not the exact type required.
Using the System
The following subsections describe how to use this server system properly and
safely, including an explanation of the server system power on/off sequences,
what the POST program checks in the server, and how to perform a forced
power shutdown.
When using the server system the following precautions should be observed.
! Do not delete the hard disk partition exclusively provided for
maintenance of the server although it may appear on the operating system
(OS). Deleting the hard disk partition may cause malfunction of the
server.
! Make sure you power off the server before connecting or disconnecting
cables between the server and peripheral devices. Connecting or
disconnecting the cables while the server is powered on may cause
malfunction or failures within the server.
Setting Up the System 2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
! Verify that the access lamp on the diskette drive is unlit before turning off
the server or ejecting the floppy disk. Turning off the server or ejecting
the floppy disk while the access lamp is lit may damage data being stored
on the floppy disk.
! After turning off the server, wait at least 40 seconds before turning it on
again. Cycling the power immediately may cause malfunction or failures
of the server.
! Before relocating the server, turn off the power and unplug the power
cord from the outlet. Moving the server when it is powered may cause
malfunction or failures of the server.
! Some software includes a command to eject the CD-ROM tray or a media
in a device mounted in the 5.25-inch device bay. Make sure that the front
door of the tower-based cabinet is open before running the command.
Running this command with the front door closed may cause the CD-
ROM tray or the media to hit against the front door, resulting in a
possible failure of the CD-ROM.
! Clean the server regularly. Regular cleaning prevents failures of the
server and its components.
! Lightning may cause a momentary voltage drop. To prevent this problem,
an uninterruptible power supply unit is recommended.
! Only use options qualified for the server. A non-qualified option may be
mounted or connected to the server, but it may fail to operate normally or
even cause failures. These types of failures are not covered under
warranty.
Opening the Front Door of the Tower Cabinet
You must open the front door of the tower cabinet to turn the server power on or
off, place the server in sleep mode, mount or dismount a floppy disk, mount or
dismount a hard disk drive, or mount or dismount 5 1/4-inch removable media
devices.
Note: The standard CD-ROM drive and some options for
the 5 1/4-inch devices such as a CD-ROM drive have a
function to eject a tray or media using a software command.
Before issuing a software command to eject a tray or media,
confirm that the front door is open. If the command is
executed while the front door is closed a tray or media may
run into the front door resulting in an error or may cause the
unit to fail.
2-6 Setting Up the System
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering On Your System
Power on your system as follows.
1. Make sure all external devices, such as a video display, keyboard, and
mouse (optional) have been connected, and the power cords are connected.
2. Power on the video display and any other external devices.
Note: If the server power cord(s) is connected to a
power control unit such as an UPS (Uninterruptible Power
Supply) make sure that the power control unit is powered on.
3. Open the front door (tower-based system only) and press the push-button
power on/off switch on the front panel. Verify that the system power-on
LED is lit. If it is not lit, ensure the ac power cord is connected to a
functional ac power source.
After a few seconds your system begins the internal Power-On Self Tests
(POST). POST automatically checks the system board, CPU(s), memory,
keyboard, mouse, and most installed peripheral devices. POST also displays the
start messages of the BIOS setup utility during execution.
The POST check results should be checked in the following cases:
! When the server is being used for the first time.
! When the server appears to fail.
! When the server beeps many times between power-on and OS start-up.
! When an error message appears on the display unit.
Note: For error messages that appear on the display
unit, refer to subsection POST Error Codes and Messages in
Chapter 5 of this Guide.
!
CAUTION
Always allow POST to complete before powering down your
system.
If you have problems powering on your system, refer to Problem Solving in
Chapter 5 of this User’s Guide.
After you have successfully powered on your system, insert the
EXPRESSBUILDER CD-ROM into the CD-ROM device, reboot the system
and follow the screen prompts to run EXPRESSBUILDER.
Setting Up the System 2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering Off the Server System
When server system power is on, pressing the power on/off switch on the front
panel of the server turns the power off.
To turn the server system power off:
1. Shutdown the operating system (OS).
2. Press the power on/off switch on the front panel of the server. The power-on
LED goes out.
3. Power off the peripheral devices.
Note: If the server power cord is connected to a power
control unit such as an UPS (Uninterruptible Power Supply),
refer to the UPS user's guide for proper power-off
procedures.
Forcing a Power Shutdown
A forced power shutdown can be used when the power on/off switch does not
power off the server or the reset functions do not work.
To perform a forced power shutdown:
Press in on the power on/off switch located on the front panel of the
server for at least 4 seconds to force the server power off.
To power on after a forced shutdown, wait 10 seconds and then power on again.
2-8 Setting Up the System
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Configuring Your System
! Configuring Your System
! BIOS Setup Utility
! SCSISelect Utility
! Configuring the RAID Controller
! Configuring System Board Jumpers
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring Your System
Configuration and setup utilities are used to change your system configuration.
You can configure your system, as well as option boards you may add to your
system, using the BIOS Setup Utility. Several unique system parameters are
configured using the BIOS Setup, which is stored in the system FLASH
memory.
The SCSISelect Utility detects the SCSI host adapters on the system board. Use
this utility if you need to configure the two SCSI controllers in your system or to
perform a SCSI disk format or verify disk operation on the SCSI disk drives.
The Adaptec Configuration Utility is also used to configure any SCSI
removable media devices installed in your system.
If your system has been factory configured, the BIOS Setup or SCSISelect
Utility do not need to be run unless you want to change the password or security
features, add certain types of option boards or devices, or upgrade your system
board.
This chapter also provides information on several system configuration
parameters that are set by jumpers on the system board. However, these
parameters do not usually require change.
Use the EXPRESSBUILDER CD-ROM to create the device driver diskettes.
3-2 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
The BIOS Setup Utility is used to change system configuration parameters. The
utility is resident in the system FLASH memory and does not require a diskette
or an operating system present to run.
Using the BIOS Setup Utility
You access the BIOS Setup utility when you turn on or reboot your system. To
run the BIOS Setup Utility, perform the following procedure:
1. Power-on or reboot the system. “Press <F2> to enter SETUP” displays.
2. Press F2. The BIOS Setup Utility starts and the Main Menu is displayed.
The menu bar at the top of the Main Menu lists the following selections:
Menu
Use
Main
Use this menu for basic system configuration.
Advanced
Use this menu for setting the Advanced Features available on
your system.
Security
Use this menu to set User and Supervisor Passwords and the
Backup and Virus-Check reminders.
Server
Boot
Exit
Use this menu for configuring unique Server features.
Use this menu to configure Boot Device priority.
Exits the current menu.
Use the arrow keys to select a menu or an item on a displayed menu. Press
the value keys (listed in the table below) to cycle through the allowable
values for the selected field. Use the Exit menu’s “Save Values” selection to
save the current values on all the menus.
To display a submenu, position the cursor on a selection that has a submenu
and press ENTER. An arrow precedes selections with submenus.
Refer to the following table for information on the keys that you use with
BIOS Setup. These keys are also listed at the bottom of the Setup menu.
Configuring Your System 3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Key
Function in Setup Menu
F1 or Alt-H
Get Help about an item.
ESC
Exit the current menu and return to the previous menu.
Move between menus.
Left or right arrow keys
Up or down arrow keys
Move cursor up and down. The cursor moves only to the
settings that you can change.
HOME or END
Move cursor to top or bottom of window.
Move cursor to next or previous page.
Select the previous value for the field.
Select the next value for the field.
PAGE UP or PAGE DOWN
F5 or -
F6 or + or SPACE
F9
Load default configuration values for this menu.
Save configuration values and exit.
F10
ENTER
Execute command or Select ➨ submenu.
BIOS Setup Configuration Settings
The BIOS Setup Configuration tables show the default settings for the BIOS
Setup Utility and provide a place for you to record any changes you make to
these settings. Recommended values are bold in the following tables.
3-4 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu
Choices or
Feature
Display Only
Description
Your Setting
System Time
HH:MM:SS
Set the System Time.
System Date
Floppy A
MM/DD/YYYY
Set the System Date.
Hidden if not detected.
Disabled
1.44/1.25 Mb 3½”
720Kb 3.5”
2.88MB 3.5”
Disabled
Floppy B
Hidden if not detected.
1.44 / 1.25 Mb 3½”
720Kb 3.5”
2.88MB 3.5”
Disabled
Hard Disk Pre-delay
Allows additional time for
slower spin-up drives to come
ready.
3 seconds
6 seconds
9 seconds
12 seconds
15 seconds
21 seconds
30 seconds
Primary IDE Master
Primary IDE Slave
Selects sub-menu
Selects sub-menu
Selects sub-menu
Secondary IDE
Master
Secondary IDE Slave
Processor Settings
Language
Selects sub-menu
Selects sub-menu
English (US)
French, German
Spanish, Italian
Selects which language BIOS
displays. Note: This feature
immediately changes to the
language BIOS selected.
Configuring Your System 3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Primary and Secondary Master and Slave IDE Submenus
Choices or
Feature
Display Only
Description
Your Setting
Auto
Type
Select Auto if a device is
None
attached to the IDE channel.
Disabled
2 Sectors
4 Sectors
8 Sectors
16 Sectors
Multi-Sector Transfer
Specifies the number of
sectors that are transferred
per block during multiple
sector transfers. This field is
informational only, for Type
Auto.
PI0 Mode
Standard
FPIO 1
FPIO 2
FPIO 3
FPIO 4
Select the method for moving
data to/from the drive. This
field is informational only, for
Type Auto. This field is
updated to display only the
modes supported by the
attached device.
FPIO 3 / DMA 1
FPIO 4 / DMA 2
Mode 2
Ultra DMA
Selects the Ultra DMA mode
used for moving data to/from
the drive. This field is
informative only for Type
Auto.
Processor Settings Submenu
Choices or
Feature
Display Only
Description
Your Setting
Processor POST
Speed Setting
Information Only
Displays measured processor
speed.
Disabled
Processor Retest
If yes, BIOS will clear
Enabled
historical processor status
and retest all processors on
the next boot. After retesting,
BIOS resets this option
automatically to “Disable”.
Hyper-Threading
Disabled
Enabled
Specifies whether Hyper-
Threading Technology is
enabled or disabled.
CPUID
Not Installed
Disabled
Processor 1 CPUID
Reports CPUID for Processor
1, if present. If empty, reports
Vacant. If disabled by BMC,
reports Disabled.
Processor 1 L2 Cache Information Only
Size
Displays L2 Cache Size for
Processor 1.
Processor 2 CPUID
CPUID (OFXX)
Not Installed
Disabled
Reports CPUID for Processor
2, if present. If empty, reports
Vacant. If disabled by BMC,
reports Disabled.
Processor 2 L2 Cache Information Only
Size
Displays L2 Cache Size for
Processor 2.
3-6 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Menu
Choices or
Description
Your Setting
Feature
Display Only
PCI Configuration
Select sub-menu.
Peripheral Configuration Select sub-menu.
Memory Configuration
Select sub-menu.
Select sub-menu.
Advanced Chipset
Control
Specifies whether POST
messages are displayed.
Disabled
Enabled
Boot-time Diagnostic
Screen
If this item is set to "Disabled,"
the logo appears during POST.
The Boot-time Diagnostic
Screen is automatically enabled
if redirection is enabled.
No
Yes
Reset Configuration
Data
Select ‘Yes’ if you want to clear
the System configuration Data
during next boot. Automatically
reset to ‘No’ in next boot.
Numlock
On
Sets power on Numlock state.
Off
Configuring Your System 3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
PCI Configuration Menu
Choices or
Feature
Display Only
Description
Your Setting
Onboard NIC 1
(10/100MB)
Select sub-menu.
Onboard NIC 2
(1.0GB)
Select sub-menu.
Onboard SCSI
Onboard Video
PCI Slot 1 ROM
Select sub-menu.
Select sub-menu.
Disabled
Enabled
Used to enable or disable an
option ROM that may be
present on a PCI add-in card
connected to the full-height
riser card.
PCI Slot 2 ROM
PCI Slot 3 ROM
PCI Slot 4 ROM
PCI Slot 5 ROM
PCI Slot 6 ROM
Disabled
Enabled
Used to enable or disable an
option ROM that may be
present on a PCI add-in card
connected to the full-height
riser card.
Disabled
Enabled
Used to enable or disable an
option ROM that may be
present on a PCI add-in card
connected to the full-height
riser card.
Disabled
Enabled
Used to enable or disable an
option ROM that may be
present on a PCI add-in card
connected to the low-profile
riser card.
Disabled
Enabled
Used to enable or disable an
option ROM that may be
present on a PCI add-in card
connected to the low-profile
riser card.
Disabled
Enabled
Used to enable or disable an
option ROM that may be
present on a PCI add-in card
connected to the low-profile
riser card.
3-8 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
Onboard NIC 1 / Onboard NIC 2 Submenu
Description
Your Setting
Choices or
Feature
Display Only
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Onboard NIC 1
Enables or disables onboard LAN
controller.
Onboard NIC 2
Enables or disables onboard LAN
controller.
Enables or disables onboard LAN
controller expansion ROM.
Enables or disables onboard LAN
controller expansion ROM.
Onboard NIC 1
ROM
Embedded NIC 2
ROM
Onboard SCSI Submenu
Description
Your Setting
Choices or
Feature
Display Only
Enabled
Disabled
Enabled
Disabled
Onboard SCSI
Enables or disables onboard SCSI
controller.
Onboard SCSI
ROM
Enables or disables onboard SCSI
ROM
Onboard Video Submenu
Description
Your Setting
Choices or
Feature
Display Only
Enabled
Disabled
Onboard Video
Enables or disables onboard video
controller.
Peripheral Configuration Submenu
Description
Your Setting
Choices or
Feature
Display Only
Serial Port A (DB-
9) Address
Disabled
3F8
2F8
3E8
2E8
4
Used to configure the base I/O
address for serial port 1.
Serial Port A (DB-
9) IRQ
Used to configure the interrupt for
serial port 1.
3
Serial Port 2 B
(RJ45) Address
Disabled
3F8
2F8
3E8
2E8
4
Used to configure the base I/O
address for serial port 2.
Serial Port B
(RJ45) IRQ
Used to configure the interrupt for
serial port 2.
3
Parallel Port
Address
Disabled
Disables the parallel port or selects
base address for parallel port.
378
278
3BC
5
Parallel Port IRQ
Selects the interrupt (IRQ) for parallel
port.
7
Parallel Port Mode Normal
Selects the parallel port operation
mode.
Configuring Your System 3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Bi-Directional
EPP
ECP
1.7
1.9
EPP Version
Selects the version for Enhanced
Parallel Port (EPP) mode.
ECP Mode DMA
Channel
0
1
2
Selects the DMA channel for
Extended Capabilities Port (ECP)
mode.
3
Legacy USB
Support
Disabled
Keyboard Only
Auto
Keyboard and
Mouse
Disables or enables support for USB
keyboards and mice. Set to Enable for
use with a non-USB aware operation
system such as DOS.
PS/2 Mouse
Support
Disabled
Enabled
Specify whether the mouse is enabled
or disabled.
Memory Configuration Submenu
Description
Your Setting
Choices or
Feature
Display Only
Extended
Memory Test
1 MB
1 KB
Extended memory test options run during
POST.
1MB: Tests every 1-MB memory.
1KB: Tests every 1-KB memory.
Every-Location: Tests every memory location.
Disabled: Initializes memory.
Every-Location
Disabled
Installed
Disabled
Not Installed
DIMM Bank #1
(DIMM1A,
DIMM1B)
Indicates the current memory status.
"Normal" indicates the normal status, "Error"
indicates a memory error, and "None"
indicates no DIMM installed (view only).
Bank #1 indicates DIMMs in DIMM sockets
#1A and #1B.
(Memory is interleaved so that two DIMMs
are used per bank.)
Installed
Disabled
Not Installed
DIMM Bank #2
(DIMM2A,
DIMM2B)
Indicates the current memory status.
"Normal" indicates the normal status, "Error"
indicates a memory error, and "None"
indicates no DIMM installed (view only).
Bank #2 indicates DIMMs in DIMM sockets
#2A and #2B.
(Memory is interleaved so that two DIMMs
are used per bank.)
Disabled
Enabled
Memory
Retest
Clears memory error information and retests
all DIMMs on the next system boot. This
option will be automatically reset to
[Disabled] on the next system boot.
Advanced Chipset Control Submenu
Description
Your
Choices or
Setting
Feature
Display Only
Disabled
Enabled
Wake on Ring
Enables or disables the remote
power-on features via serial port
(modem).
Disabled
Enabled
Wake on LAN
Enables or disables the remote
power-on features via network .
3-10 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
Wake on PME
Disabled
Enabled
Enables or disables the remote power-
on features by PCI device (PCI Power
Management Enable wake up event)
installed to the PCI riser C.
Wake on RTC
Alarm
Disabled
Enabled
Enables or disables the remote power-
on features using RTC Alarm features.
Security Menu
Note: Enabling the Supervisor Password field requires a
password for entering Setup. The passwords are not case
sensitive.
Description
Your Setting
Choices or
Feature
Display Only
User Password is Installed
Not Installed
Installed
Indicates whether the user password is set (view
only).
Administrator
Password is
Indicates whether the administrator password is
set (view only).
Not Installed
Set Admin
Password
Up to 7
alphanumeric
characters
Press Enter to display the administrator
password entry screen. With the administrator
password, all SETUP menus are available for
access. This option is available only when you
log into the SETUP utility with the administrator
password.
Set User
Password
Up to 7
alphanumeric
characters
Press Enter to display the user password entry
screen. With a user password, only certain
menus are accessible. This option is available
only if the Administrator Password is specified.
Password On Boot Disabled
Specify whether to request a password entry at
boot-up. Administrator password setup is
required.
Enabled
Fixed Disk Boot
Sector
None
Prevents data from being written to IDE hard
disks. The server does not support IDE hard
disks.
Write Protect
Secure Mode
Timer
1 minute
2 minutes
5 minutes
10 minutes
20 minutes
60 minutes
120 minutes
L
Set the period from no input from the keyboard or
mouse to the point at which the system enters
into the secure mode. If this item is set to
"Disabled," the system does not enter the secure
mode.
Security Hot Key
CTRL-ALT-
Specify the hot key to invoke secure mode
features. Pressing the assigned key along with
Ctrl and Alt invoke secure mode. This option is
enabled when User Password is set.
Z
Secure Mode Boot Disabled
Specify whether the system boots in secure
mode. This option is enabled when User
Password is set.
Enabled
Video Blanking
[Disabled]
Enabled
Specify whether to turn off the monitor when
secure mode is activated.
Power Switch
Inhibit
Disabled
Enables or disables the POWER switch. If
"Enabled" is selected, power-off with the
POWER switch becomes unavailable after OS
boot-up. (Forced shut down also becomes
unavailable. Forced shut down is a feature to
shut down by pressing the POWER switch for at
least four seconds.)
Enabled
Diskette Write
Protect
[Disabled]
Enabled
Controls access to the floppy disk drive during
the secure mode.
Configuring Your System 3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Server Menu
Choices or Display Description
Only
Your
Setting
Feature
Select Submenu
Select Submenu
Select Submenu
System
Management
Console
Redirection
Event Log
Configuration
Assert NMI on
PERR
Disabled
Sets support of PCI PERR.
Enabled
Assert NMI on
SERR
Disabled
Enabled
Sets support of PCI SERR.
Disable BSP
Do not Disable BSP
Retry 3 Times
Disable FRB2 Timer
Disabled
FRB-2 Policy
Set this item to "Disable BSP."
BMC IRQ
AC-Link
Sets the BMC IRQ.
IRQ 5
IRQ 11
Stays Off
Sets the AC-LINK feature.
Last State
Power On
Disabled
Determines the mode of operation if a
power loss occurs.
Temperature
Sensor
Enables or disables temperature sensor
monitoring feature.
Enabled
POST Error
Pause
Disabled
Enabled
Specifies whether the system waits for
user intervention on critical POST errors.
If no keyboard is connected to the
system, this option is ignored and the
system always continues to bootup.
Platform Event Disabled
Disable or enable the event report
function of Baseboard Management
Controller (BMC).
Filtering
Enabled
Disabled
Boot
Monitoring
Indicates whether the boot monitoring
function is enabled or disabled and the
timer value on booting.
5 minutes
10 minutes
15 minutes
20 minutes
25 minutes
30 minutes
35 minutes
40 minutes
45 minutes
50 minutes
55 minutes
60 minutes
To use this function, install ESMPRO
Agent. Do not use this function if the
system is booted from OS without
installation of ESMPRO Agent or CD-
ROM. Set this item to "Disabled" if
ARCServe uses the Disaster Recovery
Option.
3-12 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
Server Menu (Continued)
Choices or Display Description
Only
Your Setting
Feature
Retry 3 Times
Retry Service Boot
Always Retest
Boot
Monitoring
Policy
This item indicates the processing at
the occurrence of timeout during boot
monitoring.
If [Retry 3 times] is selected, the system
is reset after the occurrence of timeout
and OS boot is retried up to three times.
The failure in the third boot causes the
boot to be tried from the service
partition*.
If [Retry Service Boot] is selected, the
system is reset after the occurrence of
timeout and OS boot is retried up to
three times. Then the boot is tried from
the service partition for three times. The
system halts if the system fails to boot
from the service partition.
If [Always Reset] is selected, the
system is reset after the occurrence of
timeout and OS boot is retried
repeatedly.
* If no service partition exists in the
system, BIOS continues to bootup
from the system partition.
System Management Submenu
Choices or Description
Display
Your Setting
Feature
Only
Board Part Number
Board Serial Number
System Part Number
System Serial Number
Chassis Part Number
Chassis Serial Number
BIOS Version
–
Indicates the part number of mother
board. (View only)
Indicates the serial number of mother
board. (View only)
Indicates the system part number. (View
only)
Indicates the serial number of system.
(View only)
Indicates the part number of chassis.
(View only)
Indicates the serial number of chassis.
(View only)
Indicates BIOS version number. (View
–
–
–
–
–
–
–
only)
BMC Device ID
Indicates the device ID of BMC
(Baseboard Management Controller.
(View only)
BMC Firmware
Revision
–
–
Indicates BMC (Baseboard
Management Controller) firmware
revision number. (View only)
Indicates BMC (Baseboard
Management Controller) device revision
number. (View only)
BMC Device Revision
PIA Revision
–
–
–
Indicates the revision of PIA (Platform
Information Area). (View only)
Indicates the revision of SDR (Sensor
Data Record). (View only)
Indicates primary HSBP (Hot-Swap
Backplane) revision number. (View
only)
SDR Revision
Primary HSBP Revision
Configuring Your System 3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Secondary HSBP
Revision
–
Indicates secondary HSBP (Hot-Swap
Backplane) revision number. (View
only)
Console Redirection Submenu
Choices or Display Description
Only
Your Setting
Feature
Disabled
BIOS
Redirection
Port
Specify the serial port to which a
hardware console is connected.
Serial Port A (DB-9)
Serial Port B (RJ45)
Disabled
Serial Port A (DB-9)
Serial Port B (RJ45)
9600
ACPI
Redirection
Port
Specify the serial port to which an ACPI
console is connected.
Baud Rate
Selects a baud rate for communications
with the connected HW console.
19.2k
57.6k
115.2k
Flow Control No Flow Control
CTS/RTS
Select a flow control method.
XON/XOFF
CTS/RTS+CD
VT100+
VT-UTF8
PC ANSI
Terminal
Type
Specify the type of remote console.
Event Log Submenu
Choices or
Description
Your Setting
Feature
Display Only
No
Yes
Clear All Event
Logs
Clears the DMI event log after a system
reboot.
3-14 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Menu
Choices or Display Description
Only
Your Setting
Feature
Boot Device
Priority
Hard Disk
Drives
Removable
Devices
ATAPI
CDROM
Drives
Select sub-menu.
Select sub-menu.
Select sub-menu.
Select sub-menu.
Boot Device Priority Submenu
Choices or Display Description
Only
ATAPI CD-ROM
Your Setting
Feature
1st Boot
Device
Attempts to boot from an ATAPI CD-ROM
drive.
2nd Boot
Device
Removable Devices Attempts to boot from a removable media
device.
3rd Boot
Device
Hard Drive
Attempts to boot from a hard drive device.
4th Boot
Device
IBA 4.1.04 Slot 0118 Attempts to boot from a network devices
connected to the LAN port 1.
5thBoot
Device
IBA GE Slot
0120v1109
Attempts to boot from a network devices
connected to the LAN port 2.
Hard Drives Submenu
Item
Description
1. Drive #1 (or actual drive name)
2. Other bootable cards
"Other bootable cards" cover all the boot devices not
reported to the system BIOS through BIOS Boot
Specification mechanisms. It may or may not be
bootable, and may not correspond to any device.
Configuring Your System 3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Removable Devices Submenu
Item
Description
Lists Bootable Removable
devices in the system.
Select one of the detected devices.
This list includes legacy 1.44-MB floppy drives and 120-
MB floppy drives.
Lists ATAPI CDROM Drives
Selects the Boot sequence from available devices.
Exit Menu
You can make the following selections on the Exit Menu. Select an option
using the up or down arrow keys, then press <Enter> to execute the option.
Pressing <Esc> does not exit this menu. You must select one of the items from
the menu or menu bar to exit.
Choices
Description
Exit Saving Changes
Exit after writing all modified Setup item values to NVRAM.
Exit Discarding Changes
Exit leaving NVRAM unmodified. User is prompted if any of
the setup fields were modified.
Load Setup Defaults
Load Custom Defaults
Load default values for all SETUP items.
Load values of all Setup items from previously saved Custom
Defaults. NOTE: This is hidden if custom defaults are not
valid or present.
Save Custom Defaults
Discard Changes
Stores Custom Defaults in NVRAM.
Read previous values of all Setup items from NVRAM.
3-16 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSISelect Utility
The SCSISelect Utility detects and configures the SCSI controller located on the
system board or an optional SCSI controller board installed in your system. This
utility may be started with a simple key operation while POST is in progress and
requires no specific start-up disk.
The SCSISelect Utility is used mainly to set the transfer rate of connected SCSI
device. Use the SCSISelect Utility to:
! Change default values
! Check and/or change SCSI device settings that may conflict with those of
other devices in the server.
Running the SCSISelect Utility
You access the SCSISelect Utility when you turn on or reboot your system.
To run the utility, perform the following procedure:
1. Power-on or reboot the system.
2. When this message appears on the video monitor:
Press Ctrl-A to run SCSI Utility...
3. Press Ctrl+A to run this utility. The SCSI utility starts. When the Adaptec
SCSI Utility detects more than one AIC-79xx host adapter, it displays a
selection menu listing the bus and device number of each adapter. When the
selection menu appears, select the channel you wish to configure as follows:
Bus : Device : Channel
Selected SCSI Adapter
04 : 07 : A*
AIC-7901
*Internal SCSI connector.
4. Once you select the adapter, the following screen is displayed:
Menu
Description
Configure/View Host
Adapter Settings
Configure host adapter and device settings.
SCSI Disk Utilities
The utility scans the SCSI bus for SCSI devices, reports a
description of each device. Run these utilities before
configuring SCSI devices.
5. If you wish to format a disk, verify disk media, or display a list of devices
and their SCSI IDs, select “SCSI Disk Utilities”. If you wish to configure
the adapter or a device, select “Configure/View Host Adapter Settings”.
Configuring Your System 3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Adaptec SCSI Utility Configuration Settings
The following keys are active for all Adaptec SCSI Utility screens:
Key
Action
Arrows
ENTER
ESC
F5
Up and down arrows move from one parameter to another within a screen.
Displays options for a configurable parameter. Selects an option.
Moves back to previous screen or parameter or EXIT if at the Main menu.
Switches between color and monochrome.
F6
Resets to host adapter defaults.
The following table shows the normal settings for the Adaptec SCSI Utility and
provides a place for you to record any changes you make to these settings.
Table 3-1. SCSISelect Utility Setup Configurations
RECOMMENDED SETTING
OR DISPLAY ONLY
YOUR
CONFIGURATION
OPTION
SCSI Bus Interface Definitions
SCSI Controller ID
7
SCSI Controller Parity
SCSI Controller Termination
Additional Options
Enabled
Enabled
Boot Device Configuration
Master SCSI Controller
SCSI Device Configuration
Sync Transfer Rate (MB/Sec)
Packetized
Press ENTER for menu
AIC-7901 at Slot 0004:07:00
Press ENTER for menu
320
Yes
QAS
Yes
Initiate Wide Negotiation
Enable Disconnection
Send Start Unit Command
BIOS Multiple LUN Support
Include in BIOS Scan
Advanced Configuration
Reset SCSI Bus at IC Initialization
Yes
Yes
Yes
No 1
Yes 1
Press ENTER for menu.
Enabled
1 No effect if BIOS is disabled.
3-18 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-1. SCSISelect Utility Setup Configurations (continued)
RECOMMENDED SETTING
OR DISPLAY ONLY
YOUR
CONFIGURATION
OPTION
Display <Ctrl-A> Messages During BIOS
Enabled
Enabled
Initialization
Extended Int13 Translation for DOS
Drives >1 GByte
POST Display Mode
Verbose
SCSI Controller Int13 Support
Domain Validation
Enabled1
Enabled1
Disabled1, 2
Support Removable Disks
Under Int13 as Fixed Disks
BIOS Support for Bootable CDROM
BIOS Support for Bootable CDROM
Enabled1
Enabled1
1 No effect if BIOS is disabled.
2 Do not remove media from a removable media drive if it is under BIOS control.
SCSI Disk Utilities
This utility scans the SCSI bus for SCSI devices, reports a description of each
device. Run these utilities before configuring SCSI devices.
To enter the utility, select "SCSI Disk Utilities" on the Options menu.
The SCSI ID scan begins displaying the message as shown below.
Scan n in g SCSI ID : 0
LUN Nu m ber : 0
When the SCSI ID scan completes, the screen listing SCSI IDs and associated
devices appears.
Select SCSI Disk and press <Enter>
SCSI ID #0 : No device
SCSI ID #1 : No device
SCSI ID #2 : No device
SCSI ID #3 : No device
SCSI ID #4 : No device
SCSI ID #5 : No device
SCSI ID #6 : No device
SCSI ID #7 : Adaptec AIC-7901
SCSI ID #8 : No device
SCSI ID #9 : No device
SCSI ID #10 : No device
SCSI ID #11 : No device
SCSI ID #12 : No device
SCSI ID #13 : No device
SCSI ID #14 : No device
SCSI ID #15 : No device
Configuring Your System 3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
With this screen you can determine the SCSI IDs for installed options. You can
also view the device information by selecting a device and pressing Enter.
The following sub menu appears.
SCSI ID#4
Firm ware
: xxxxxxxxx
: xxxx xxx
Capacity : xxGB
Form at
Verify Disk Media
The following table lists submenu items and descriptions.
Submenu item
Description
Format
Formats the selected device.
Verify Disk Media
Verifies all the sectors in the selected device. If one
or more bad sectors are found, the sectors are
remapped.
Exiting Adaptec SCSI Utility
To exit the Adaptec SCSI Utility, press ESC until a message prompts you to exit
(if you changed any settings, you are prompted to save the changes before you
exit).
3-20 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the RAID Controller
RAID (Redundant Array of Independent Devices) options are available for your
system, providing added security and high availability.
If you order a system with a RAID controller, the system is pre-configured at
the factory according to Table 3-2 below.
Table 3-2. RAID Configurations
Number of
Hard Drives Configured
RAID Level
Hard Drives in
Array
Description
JBOD (RAID 7) Known as Just a Bunch of Drives,
JBOD allows the controller to access the drives
independently. This configuration has no redundancy
and does not use striping.
1
7
1
Mirroring (RAID 1) Drives are paired and mirrored.
All data is 100% duplicated on an equivalent drive
(fully redundant).
2
1
5
5
2
3
Striping with Parity (RAID 5) Data is striped across
several physical drives. Parity protection is used for
data redundancy.
3
Striping with Parity (RAID 5) with a standby drive
The array consists of three ON-LINE drives and one
STANDBY drive. The standby replacement drive, or
hot spare, is one of the most important features RAID
provides to achieve automatic, non-stop service with a
high degree of fault-tolerance.
4 or more
4 (one standby
drive)
If you want to change the RAID level or add additional hard disks to the array,
use the RAID configuration utility. The RAID configuration utility is included
with the RAID controller.
If you are adding the RAID controller to an existing system, the RAID
configuration utility allows you to configure your disk array before reinstalling
your network operating system. The RAID controllers support various versions
of RAID technology (referred to as RAID levels). To use any RAID level, you
must configure the RAID controller using the RAID configuration utility prior
to installing your Network Operating System. For an explanation of this utility,
refer to the documentation that was shipped with the RAID controller. It
describes RAID technology and provides tips on making your array perform
well in your specific application. It also covers array hardware preparation,
configuration, and initialization. After completing the steps in the manual, you
can install your Network Operating System.
If you want to remotely configure the array (from a PC client); increase array
capacity online; or monitor statistics on disk and controller activity, you must
install the array manager provided with your RAID subsystem. Increasing array
capacity is covered in the user's guide shipped with the option.
Configuring Your System 3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring System Board Jumpers
Before You Begin
Only a qualified technical person should perform the procedures in this section.
!
CAUTION
Electrostatic discharge (ESD) can damage the system
board. Modify the system board only at an ESD workstation.
Otherwise, wear an antistatic wrist strap attached to chassis
ground.
The system board jumpers enable you to set specific operating parameters for
your system. A jumper is a small plastic-encased conductor (shorting plug) that
slips over two jumper pins.
Figure 3-1 shows the location of system board jumpers. Referring to Figure 3-1,
jumper A is the CMOS clear configuration jumper. Jumper B shown in Figure
3-1 is the password clear configuration jumper. Table 3-3 lists the factory
default settings for the CMOS and password configuration jumpers.
CMOS CLR:
Pin for protecting/
clearing the CMOS
contents (The figure
shows the factory-set.)
PASSWD CLR: Pin for protecting/
clearing the password
: Strapped
CMOS PASSWD RECOVERY BMC FLASH
CLR
CLR
BOOT
EN
B
C
A
A
B
C
CMOS Clear
Password Clear
Factory Setting (Do not
change)
Figure 3-1. System Board Jumpers
3-22 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-3. Password/CMOS System Board Jumper Summary
Jumper On/Off
Jumper
Function
(default in bold)
What it does at system reset.
Off, Protect
On, Erase
A
CMOS clear
Preserves the contents of CMOS.
Clears CMOS.
Off, Enable
On, Disable
B
C
Password disable
Reserved
Enables password protection.
Disables the password.
Off, Not Used
Do Not Change.
Moving System Board Jumpers
!
CAUTION
Before doing the procedures in this section, make sure that
your system is powered off and unplug the AC power cords
from the back of the chassis. Failure to disconnect power
before moving the jumpers can result in personal injury and
equipment damage.
Observe static precautions. Use an antistatic wrist strap.
Clearing CMOS
Clear CMOS as follows.
1. Shut down the OS.
2. Press the POWER switch to turn off the power of the server. (The
POWER/SLEEP lamp goes off.)
3. Remove the side cover. Refer to Chapter 4 for information on removing the
side cover.
4. Remove the system power cord from the back of the system.
5. Locate the position of the CMOS jumper on the system board.
See Figure 3-1. To change a jumper setting, use a pair of needle-nose pliers
or your fingers to remove the jumper from its current location. Position the
jumper over the two pins shown at Figure 3-1, A and press it onto the pins.
Be careful not to bend the pins. Also refer to Table 3-3 for system board
jumper setting descriptions.
6. Connect the power cord, power on the system and after POST completes,
power down the system and unplug the power cord.
7. Remove the CMOS jumper to its original position.
8. Replace the side cover, connect the power cord, and power on the system.
9. Press F2 at the prompt to run the BIOS Setup utility, and select “Get Default
Values” at the Exit menu.
Configuring Your System 3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing and Changing the Passwords
To clear and change the passwords:
1. Shut down the OS.
2. Press the POWER switch to turn off the power of the server. (The
POWER/SLEEP lamp goes off.)
3. Remove the side cover. Refer to Chapter 4 for information on removing the
side cover.
4. Remove the system power cord from the back of the system.
5. Locate the position of the password jumper on the system board.
See Figure 3-1. To change a jumper setting, use a pair of needle-nose pliers
or your fingers to remove the jumper from its current location. Position the
jumper over the two pins shown at Figure 3-1, B and press it onto the pins.
Be careful not to bend the pins. Also refer to Table 3-3 for system board
jumper setting descriptions.
6. Connect the power cord, power on the system and after POST completes,
power down the system and unplug the power cord.
7. Remove the password jumper to its original position.
8. Replace the side cover, connect the power cord, and power on the system.
9. Press F2 at the prompt to run the BIOS Setup utility. Specify a new
password, if desired.
3-24 Configuring Your System
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Disassembly and Reassembly
! General Information
! Static Precautions
! Equipment Log
! Tools Recommended for Upgrading Your System
! Preparing Your System for Disassembly and
Reassembly
! Side Access Panel
! Processor Air Duct
! Modifying the System Board
! Hard Disk Drives
! Hot-Swap Power Supply
! Non-Hot-Swap Power Supply
! Front Cooling Fan Unit
! Removable 5.25-inch Media Devices
! PCI Boards
! RAID Controller Board
! Diskette Drive and Carrier Assembly
! Front Bezel and Front Bezel Hinge (Tower-Based
System)
! Front Panel
! Hot-Swap HDD Bay
Download from Www.Somanuals.com. All Manuals Search And Download.
! Hot-Swap SCSI Backplane
! Replacing the Rear Cooling Fan
! System Board
! Power Supply Back Board
! Tower Feet
! I/O Shield
! LED/Switch Assembly
! Intrusion Switch Assembly
4-2 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
!
WARNING
The DC push-button on/off switch on the front panel does
not turn off the system AC power. Also, +5vdc is present on
the system board whenever the AC power cord is connected
between the system and an AC outlet. Before doing the
procedures in this manual, make sure that your system is
powered off and unplug the AC power cord from the back of
the chassis. Failure to disconnect power before opening
your system can result in personal injury and equipment
damage.
!
CAUTION
Operating your system with the side access panels removed
can damage your system components. For proper cooling
and airflow, always replace the side access panels before
powering on your system.
WARNING
Avoid burns: If the system has been running, any installed
processor and heat sink on the processor board(s) will be
hot. To avoid the possibility of a burn, be careful when
removing or installing components that are located near
processors.
Contact your sales representative or dealer for a list of approved optional
peripheral devices.
Static Precautions
An electrostatic discharge (ESD) can damage disk drives, option boards, and
other components. You can provide some ESD protection by wearing an
antistatic wrist strap attached to chassis ground when handling system
components.
Electronic devices can be easily damaged by static electricity. To prevent
damage, keep them in their protective packaging when they are not installed in
your system.
Equipment Log
Use the equipment log form located at the end of this manual to record the
model and serial number of your system, all installed options, and any other
pertinent information specific to your system. You will need this information
when configuring your system.
Disassembly and Reassembly 4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools Recommended for Upgrading Your
System
Depending on the upgrade, you will need one or more of the following tools:
! Phillips screwdriver (#1 bit and #2 bit)
! Flat-head screwdriver
! Small needle nose pliers
! Pen or pencil
! ESD workstation or antistatic wrist strap (recommended)
Preparing Your System for Disassembly and
Reassembly
To prepare your system for installation or removal of system components
perform the following procedure:
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Open the front bezel of your system's cabinet. For rack-mount systems you
must remove the front panels of the system chassis.
3. Shutdown the operating system (OS).
4. Press the power on/off switch on the front panel of the server (see
Front View in Chapter 2). The power-on LED goes out.
5. Power off the peripheral devices.
6. Unplug the system power cord(s) from the AC wall outlet(s).
Note: If the system power cord is connected to a power
control unit such as an UPS (Uninterruptible Power Supply),
refer to the UPS user's guide for proper power-off
procedures.
7. Unplug all the I/O cables connected to the rear panel of your system.
4-4 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Side Access Panel
To install options in your system, you must remove the access panel on the left-
hand side of the system (as viewed from the front). The side access panel on the
right-hand side of the system (as viewed from the front) does not have to be
removed.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system.
!
WARNING
If you are removing the side access panel after the system is
set up, you must first power off the system and all external
devices and then unplug the system power cord(s).
To remove the left side access panel (see Figure 4-1):
1. Prepare your system for upgrade. See Preparing Your System for
Disassembly and Reassembly described earlier in this chapter.
2. The left-hand side access panel is secured to the chassis with two
thumbscrews. Loosen the thumbscrews securing the side access panel.
3. Using the indentation on the side of the panel, slide the side access panel
toward the rear of the system. This unlocks the locking fingers behind the
side access panel.
4. Pull the side access panel out and away from the chassis.
Disassembly and Reassembly 4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-1. Removing the Left-Hand Side Access Panel
To install the left side access panel (see Figure 4-2):
1. Check to make sure that no tools or loose parts have been left inside the
system chassis.
2. Make sure all option boards are firmly seated in their respective slots and
that all interior cables are properly connected.
3. Insert the locking fingers on the top and bottom of the side access panel into
their slots on the chassis. Then slide the side access panel forward as far as it
will go.
Note: Ensure that the side access panel is installed
properly and securely fastened. A cover sensor (intrusion
switch) monitors the left-hand side access panel.
4. Tighten the side access panel thumbscrews.
Note: If your system is already set up, plug the system
back in, reconnect the peripherals, and power on the
peripherals and system.
4-6 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-2. Installing the Left-Hand Side Access Panel
Disassembly and Reassembly 4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Processor Air Duct
To install or remove the DIMM or a processor, you will need to remove the air
duct.
IMPORTANT: Do not assemble the server without installing the air duct. If the
duct is not installed in the system, reduced cooling efficiency and can affect
performance or cause damage due to overheating.
Removal
Follow these steps to remove the air duct.
1. Prepare your system for upgrade. See Preparing Your System for
Disassembly and Reassembly described earlier in this chapter.
2. Remove the side cover.
3. Hold the left side of the air duct, and push the right end of the tab to release
from the chassis. See Figure 4-3.
4. Remove the duct from the chassis.
Figure 4-3. Removing the Air Duct
4-8 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Follow these steps to install the air duct.
1. Holding the internal cables clear, place the air duct into the chassis. See
Figure 4-4.
2. Adjust the air duct until the tab on the right end of the duct is aligned with
the slot on the chassis.
Slot
Tab
Figure 4-4. Installing The Air Duct
3. Reinstall the side cover.
Disassembly and Reassembly 4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Modifying the System Board
The following sections provide procedures for upgrading and configuring the
system board in your system. Topics covered include:
! Replacing the real-time clock battery
! Removing and installing a processor
! Installing or removing DIMMs.
!
CAUTION
Electrostatic discharge (ESD) can damage add-in boards
and other components; place them on an antistatic surface.
Modify the system board only at an ESD workstation.
Otherwise, wear an antistatic wrist strap attached to chassis
ground.
Replacing the Real-time Clock Battery
You may need to replace the real-time clock (RTC) battery because of its life
span. The battery powers the clock in the absence of power. When the battery
starts to weaken, it loses voltage, and the system settings stored in CMOS RAM
(for example, the date and time) may be wrong.
The 3V battery (Vendor Part #CR2032) is a commodity part available through
many vendors. It is located on your system board (See Figure 4-5). Notice the
plus (+) sign on the battery. This sign will assist you in correctly positioning the
battery on the system board. Contact your sales representative or dealer for a list
of approved devices.
!
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with same or equivalent type recommended by
manufacturer. Dispose of lithium batteries as required by
local ordinance or as normal waste if no local ordinance
exists. Do not expose the component to excessive heat or
fire. Keep all batteries away from children
!
CAUTION
Observe static precautions. Use an antistatic wrist strap.
4-10 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
To replace the RTC battery, perform the following procedures:
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Open the front bezel of your system's cabinet. For rack-mount systems you
must remove the front panels of the system chassis.
3. Shutdown the operating system (OS).
4. Press the power on/off switch on the front panel of the server (see
Front View in Chapter 1). The power-on LED goes out.
5. Power off the peripheral devices.
6. Unplug the system power cord(s) from the AC wall outlet(s).
Note: If the system power cord is connected to a power
control unit such as an UPS (Uninterruptible Power Supply),
refer to the UPS user's guide for proper power-off
procedures.
7. Remove the left-hand side access panel of the system chassis following
procedures previously described in this chapter.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system.
8. Remove the processor air duct. See Processor Air Duct Removal earlier in
this chapter.
9. If present, remove the protective plastic cover located over the top of the
lithium battery (see Figure 4-5).
10.Insert the tip of a small flat-bladed screwdriver, or equivalent, under the
plastic tab on the plastic retainer (see Figure 4-5, A).
11.Gently push down on the screwdriver to lift the battery (see Figure 4-5, B).
12.Remove the battery from its socket (see Figure 4-5, C).
13.Dispose of the battery according to local ordinance.
14.Remove the new lithium battery from its package, and, being careful to
observe the correct polarity (plus sign (+) up) insert it into the battery socket.
15.If applicable, reinstall the plastic cover on the lithium battery socket.
16.Reinstall the air duct.
17.Reinstall the left-hand side access panel on the system chassis.
18.Plug in the system power cord(s), and turn on the system.
Disassembly and Reassembly 4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
19.Run the BIOS Setup to restore the configuration settings to the real-time
clock.
Figure 4-5. Replacing the Real-Time Clock Battery
4-12 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Installing a Processor
This subsection provides the procedures for removing and installing a
Xeon processor in your system. The system board has sockets for two
processors. Each Xeon processor plugs into a standard Xeon ZIF socket. The
processor comes with up to 512K cache. The primary processor connector is
shown in the illustration below (see Figure 4-6, C). The secondary processor
connector is shown in the illustration below (Figure 4-6, B).
!
CAUTION
Electrostatic discharge (ESD) can damage components;
place them on an antistatic surface. Modify the system board
using an antistatic wrist strap attached to chassis ground.
C
B
A
A – System board
B –CPU #2
C –CPU #1
Figure 4-6. System Board Xeon Processor Locations
!
WARNING
If the system was running, any processor and heat sink
installed is hot. To avoid the possibility of a burn, let the
components cool for 10 minutes before continuing with these
procedures.
Disassembly and Reassembly 4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
CPU Installation
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Open the front bezel of your system's cabinet.
3. Shutdown the operating system (OS).
4. Press the power on/off switch on the front panel of the server (see
Front View in Chapter 1). The power-on LED goes out.
5. Power off the peripheral devices.
6. Unplug the system power cord(s) from the AC wall outlet(s).
Note: If the system power cord is connected to a power
control unit such as an UPS (Uninterruptible Power Supply),
refer to the UPS user's guide for proper power-off
procedures.
7. Remove the left-hand side access panel of the system chassis following
procedures previously described in this chapter.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system.
8. Remove the processor air duct. See Processor Air Duct Removal earlier in
this chapter.
9. Locate the CPU socket which you are going to install CPU.
10.Raise the locking lever on the socket. See Figure 4-7.
IMPORTANT: Open the lever until it stops. The bar can be opened to
approx. 120 degrees.
4-14 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Retention
Figure 4-7. Raising the Locking Lever
11.Aligning the pins of the CPU with the socket, insert the CPU slowly and
gently into the socket. See Figure 4-8.
IMPORTANT: Be aware of CPU direction. Pin layouts on two corners
among four differ from others to prevent an incorrect insertion. Confirm
the pin mark and pin layout on the socket, and insert the CPU correctly.
Pin mark
Figure 4-8. Installing a CPU
12.Push the CPU lightly to the socket, and push down the lever to secure the
CPU. See Figure 4-9.
Disassembly and Reassembly 4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-9. Closing the Locking Lever
13.Very carefully apply the thermal interface material (heat radiation sheet) on
top of the processor so that it is completely covered. See Figure 4-10.
Notes: The thermal material may already be applied to
the heat sink.
The thermal interface material is very fragile, it must be
handled very carefully. If the cooling sheet is damaged, it
must be replaced with a new one. Reuse of the cooling
sheet is not permitted.
Do not stick multiple cooling sheets on a processor, only one
is needed. Keep any remaining cooling sheets as spares.
Figure 4-10. Installing the Thermal Cooling Sheet
14.Install the heat sink on CPU. See Figure 4-11.
NOTE: Be aware of direction of heat sink (see figure below).
4-16 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-11. Installing the Heatsink
15.Install both heat sink clips as follows:
!
CAUTION
Do not allow the heat sink to rock back and forth while
securing the heat sink clips. If the CPU becomes dislodged
from the socket, catastrophic failure may occur.
Place the heat sink clip on the center tab of the retention module and
rotate the clip towards the heat sink to engage the center tab (1).
Repeat this step with the second clip (2). See Figure 4-12.
While ensuring the heat sink is level and secure with one hand, snap
one end of the clip down over the corresponding tab on the retention
module (3). Then snap the opposite corner clip (4). Snap the
remaining end of the clips down over the corresponding tabs (5) (6).
Be sure the clip is adequately engaged with the tab. Ensure the heat
sink is absolutely level.
2
6
4
3
5
1
Figure 4-12. Securing the Processor Heatsink
Disassembly and Reassembly 4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
16.Ensure the heat sink is level.
NOTES:
! If the heat sink is not level, remove it, and then install it again. The
following probably causes the heat sink not to be level:
– The CPU is not positioned correctly.
– The wire clip is not engaged correctly.
! Do not move the secured heat sink.
17.Reinstall the processor air duct.
18.Reinstall the left-hand side access panel on the system chassis.
19.Plug in the system power cord(s), and turn on the system.
20.Power on the server, start the SETUP utility, and set "Processor Retest" of
"Processor Settings" on the Main menu to "Enable".
21.Verify that POST displays no error messages.
22.If POST displays an error message, take a note on the message and see the
POST error messages listed in Chapter 5.
23.Run the BIOS Setup Utility. Set "Reset Configuration Data" on the
Advanced menu to "Yes". This setting is required to change the hardware
configuration data.
24.When adding a CPU to a server with one CPU installed perform the
procedure below:
For Windows 2000, change the driver of [Computer] in the device manager
to [ACPI multi-processor PC] and then update the system.
4-18 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
CPU Removal
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Prepare your system for upgrade. See Preparing Your System for
Disassembly and Reassembly described earlier in this chapter.
3. Remove the left-hand side access panel as described earlier in this chapter.
!
CAUTION
Observe static precautions. Use an antistatic wrist strap.
Hold the processor only by its edges.
4. Locate the appropriate processor on the CPU board. See Figure 4-6.
5. Remove the heat sink from the top of the processor by inserting a small
screwdriver into the slots on its heat sink clips. Release the clip pressure
points in the order (1-6) shown in Figure 4-13.
2
5
4
3
6
1
Figure 4-13. Removing the Processor Fan Heatsink
6. Swing its processor socket lever up until it is in the unlocked position and
carefully remove the processor. See Figure 4-14.
Figure 4-14. Removing the Processor
7. If you are adding or replacing a processor, refer to Installing a Processor
earlier in this chapter.
Disassembly and Reassembly 4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Reinstall the air duct.
9. Reinstall the left-hand side access panel on the system chassis.
10.Plug in the system power cord(s) and power up the system.
DIMMs
The system board contains four DIMM sockets (Figure 4-15). Each socket can
hold a single 72-bit DIMM module with 256MB, 512MB, or 1GB of memory.
When all four sockets are populated, the system board supports a maximum of 4
GB of memory with 1GB DIMMs.
Memory is partitioned as two banks of SDRAM that must be populated in pairs,
each providing 72 bits of buffered two-way interleaved memory (64-bit main
memory plus ECC). DIMMs will always be installed in sockets 1 and 2.
Note: DIMMs are always added in pairs.
DIMM #1A
DIMM group #1
DIMM group #2
DIMM #1B
DIMM #2A
DIMM #2B
1A
1B
2A
2B
DIMM #1-A
DIMM #1-B
DIMM #2-A
DIMM #2-B
DIMM Group #1
DIMM Group #2
Figure 4-15. DIMM Locations on the System Board
4-20 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing DIMMs
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Open the front bezel of your system's cabinet. For tower-based systems see
Opening the Front Bezel of the Tower Cabinet in Chapter 2. For rack-mount
systems you must remove the front panels of the system chassis.
3. Shutdown the operating system (OS).
4. Press the power on/off switch on the front panel of the server (see
Front View in Chapter 1). The power-on LED goes out.
5. Power off the peripheral devices.
6. Unplug the system power cord(s) from the AC wall outlet(s).
Note: If the system power cord is connected to a power
control unit such as an UPS (Uninterruptible Power Supply),
refer to the UPS user's guide for proper power-off
procedures.
7. Remove the left-hand side access panel of the system chassis following
procedures previously described in this chapter.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system.
8. Remove the processor air duct. See Processor Air Duct Removal earlier in
this chapter.
9. If applicable, locate the appropriate DIMM sockets on the system board (see
Figure 4-14).
10.Remove the DIMM connector covers from its socket (see Figure 4-16). Save
the DIMM connector cover for future use.
Note: If you are replacing a DIMM, you must first
remove the DIMM from its socket (see Removing DIMMs
later in this chapter).
Disassembly and Reassembly 4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-16. Removing the DIMM Connector Cover
11.Holding a DIMM module only by the edges, remove it from its antistatic
package.
!
CAUTION
Observe static precautions. Use an antistatic wrist strap.
Hold the DIMM only by its edges.
12.Position the DIMM so that the two notches in the bottom edge of the DIMM
align with the keyed socket. See Figure 4-17.
13.Insert the bottom edge of the DIMM into the socket, and press down firmly
on the DIMM until it seats correctly.
14.Gently push the plastic ejector levers on the socket ends to the upright
position to ensure that they are installed correctly.
Figure 4-17. Inserting Memory DIMMs
15.Repeat the steps to install each additional DIMM.
16.Reinstall the processor air duct.
17.Reinstall the left-hand side access panel on the system chassis.
18.Plug in the system power cord(s) and power up the system.
4-22 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing DIMMs
!
CAUTION
Use extreme care when removing a DIMM. Too much
pressure can damage the socket slot. Apply only enough
pressure on the plastic ejector levers to release the DIMM
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Open the front bezel of your system's cabinet.
3. Shutdown the operating system (OS).
4. Press the power on/off switch on the front panel of the server (see
Front View in Chapter 1). The power-on LED goes out.
5. Power off the peripheral devices.
6. Unplug the system power cord(s) from the AC wall outlet(s).
Note: If the system power cord is connected to a power
control unit such as an UPS (Uninterruptible Power Supply),
refer to the UPS user's guide for proper power-off
procedures.
7. Remove the left-hand side access panel of the system chassis following
procedures previously described in this chapter.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system.
8. Remove the processor air duct. See Processor Air Duct Removal earlier in
this chapter.
9. Locate the appropriate DIMM sockets on the system board (see
Figure 4-15).
10.Gently push the plastic ejector levers out and down to eject a DIMM from its
socket. See Figure 4-18.
11.Hold the DIMM only by its edges, being careful not to touch its components
or gold edge connectors. Carefully lift it away from the socket, and store it
in an antistatic package.
Disassembly and Reassembly 4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-18. Removing a DIMM
12.Repeat the above steps to remove the remaining DIMMs.
13.Reinstall the processor air duct.
14.Reinstall the left-hand side access panel on the system chassis.
15.Plug in the system power cord(s) and power up the system.
4-24 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Hard Disk Drives
Your system supports a variety of SCSI hard disk drives installed in the
system’s hard disk drive bay. Contact your sales representative or dealer for a
list of approved devices.
The 3.5-inch hard disk drive bay on the front of the server contains six slots on
which hard disks can be installed. A hard disk having the thickness of 1 inch can
be installed in each of the slots. The SCSI IDs of the slots are fixed to ID0 to
ID5 from bottom to top.
In the configuration at the shipment, the cable on the 3.5-inch hard disk drive
bay is connected to the Ultra320/160 SCSI (A) connector on the system board.
To provide the disk array configuration, connect the cable on the 3.5-inch hard
disk drive bay to the disk array controller. The SCSI standard of the hard disk
to be added should be the same as that of the existing disks.
A dummy tray is installed in an empty slot of the 3.5-inch hard disk drive bay.
This is intended to improve the cooling effect within the server. Always install
a dummy tray in any slot in which a hard disk is not installed.
IMPORTANT: A specified dummy tray must be used.
Installation
If installing new drives, follow an installation scheme starting with the bottom-
most drive. Fill the bays bottom-to-top.
NOTE: Hard disks can be installed or removed from the server only by
opening the front bezel. In the disk array configuration, hard disks may be
installed or removed with the power of the server on.
IMPORTANT: In the disk array configuration, hard disks configuring a
specific pack should have the same specification including the capacity.
1. See the section Preparing Your System for Disassembly and Reassembly
described earlier to prepare (in other than the disk array configuration).
2. Release the lock of the front bezel by using the security key to open the front
bezel.
3. Check the slot in which the hard disk is installed.
4. Remove the dummy tray. See Figure 4-19.
Disassembly and Reassembly 4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-19. Removing the Dummy Tray
5. Unlock the lever of the hard disk drive carrier and open the handle. See
Figure 4-20.
Figure 4-20. Unlocking the Drive Carrier
6. Align the drive carrier with the bay guide rail.
7. Slide the drive carrier into the bay until if docks with the SCSI backplane
connector. See Figure 4-21.
IMPORTANT:
! Push the hard disk drive carrier until the hook of the handle hits the
frame.
! Hold the hard disk drive carrier with both hands securely and carefully.
4-26 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Handle
Figure 4-21. Installing the Hard Disk Drive
8. Close the lever ensuring the drive is secured. The handle is locked when a
distinct click is heard.. See Figure 4-22.
Hook
Frame
Handle
Figure 4-22. Locking the Hard Disk Drive Carrier
9. Close the bezel opened in step 2.
Disassembly and Reassembly 4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal
NOTE: The disk LED of a defective hard disk drive is amber.
1. Prepare your system for upgrade. See Preparing Your System for
Disassembly and Reassembly described earlier in this chapter.
2. Release the lock of the front bezel by using the security key to open the front
bezel. See Figure 4-23.
Figure 4-23. Releasing the Hard Disk Drive Carrier
3. Press the locking tab to release the lock.
4. Grasp the drive carrier handle and pull the handle toward you to disengage
the drive connector from the backplane. See Figure 4-24.
Figure 4-24. Opening the Hard Disk Drive Carrier
5. Hold the drive carrier handle and hard disk securely and remove the hard
disk from the drive bay. See Figure 4-25.
4-28 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-25. Removing a Hard Disk Drive
6. If not replacing the hard disk removed, insert a dummy carrier tray into the
empty slot.
IMPORTANT: To maintain the cooling effect in the server, install the
dummy tray in the vacant slot of the disk bay.
7. Close the bezel opened in step 2 securely.
Auto Rebuild Functionality
If your server includes a disk array controller, the auto rebuild function can be
used to restore data from the defective hard disk drive. The auto rebuild
function can write the data saved from a defective hard disk to the replacement
disk drive thereby recovering the server to the state before the occurrence of the
fault.
The auto rebuild function is valid for disk arrays set to RAID1 or RAID5.
The auto rebuild is automatically started only by the hot-swap of a defective
hard disk (or disk replacement in the power-on state). During the auto rebuild,
the disk lamp on the hard disk is lit green or amber alternatively.
IMPORTANT: Do not turn off the power of the server in
the interval between a fault of a hard disk to the end of the
auto rebuild process.
Wait at least 90 seconds from the time you remove a
defective disk drive to the time you install the replacement
disk drive.
If a hard disk is rebuilding, do not replace another disk. (The
disk lamp on the hard disk being rebuilt is lit green or amber
alternatively.)
Disassembly and Reassembly 4-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot-Swap Power Supply
Your server may contain a modular hot-swap power supply like the one shown
in Figure 4-26. The addition of a second hot-swap power supply makes your
system so that it has redundant power and can be operated continuously without
interruption if either of the power supplies malfunction.
Installation
1. Prepare your system for upgrade. See Preparing Your System for
Disassembly and Reassembly describes earlier in this chapter.
2. Loosen a screw securing the blank cover to remove the cover from the
chassis. Remove the cover and save it for future use. See Figure 4-26.
Figure 4-26. Loosening the Blank Cover Retaining Screw
3. Press down the locking tab of the power supply handle and open the handle.
See Figure 4-27.
2
1
Figure 4-27. Preparing the Power Supply for Installation
4-30 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Slide the power supply into the vacant slot until you feel resistance. See
Figure 4-28.
IMPORTANT:
! Make sure that the handle is in full-open position.
! To avoid damaging the power supply unit, do not tilt or twist the unit as
you push it into the connector.
Figure 4-28. Installing the Power Supply
5. Push the power supply handle up. See Figure 4-29.
NOTE: Confirm that the handle is securely hooked.
Handle
Hook
Frame
Figure 4-29. Pushing up the Power Supply Handle
Disassembly and Reassembly 4-31
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Push the power supply handle toward the power supply until the locking tab
snaps into place. See Figure 4-30.
Figure 4-30. Securing the Power Supply
7. Connect two power cords to the AC inlets. The AC Power lamps go on and
DC Power lamps blink when the power cords are connected. See
Figure 4-31.
DC Power lamp
Power Status lamp
AC Power lamp
Figure 4-31. Connecting the Power Cords
8. Turn on the power of the server. The DC Power lamps on the power supplies
are lit.
4-32 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal
1. Check the Power Status lamps of the power supplies on the rear face and
determine which module needs to be replaced. (If a power supply is
defective, the Power Status lamp is lit amber.)
NOTE: When the server is equipped with two power supplies and one of
the power supplies operates normally (with the power lamp of the power
supply being on), the other defective power supply can be replaced while
the system is in operation (or in the power-on status). In this case, skip
step 2 in this procedure.
2. Shut down the system and press the POWER switch to turn off the power.
3. Disconnect the power cord from the failed power supply.
4. While pressing down on the locking tab, grasp the handle and carefully pull
the power supply out of the power supply bay. See Figure 4-32.
IMPORTANT: To avoid damaging the power supply unit, do not tilt or
twist the unit as you pull it from the power supply bay. The module
disengaging from its connector causes the initial resistance you will feel.
Use even, steady force to remove the unit.
2
1
Figure 4-32. Removing a Power Supply
5. If you are not going to install a replacement power supply unit, you must
install blank cover in the vacant slot.
IMPORTANT: To maintain the cooling effect in the server, install the
blank cover in the vacant slot of the power supply bay.
6. Install the power supply referring to steps 3 to 8 of the power supply
installation procedure.
Disassembly and Reassembly 4-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Non-Hot-Swap Power Supply
Your server system may contain a single non-hot-swap power supply that is
housed in the rear of the chassis as shown in Figure 4-33.
Removal
1. Prepare your system for disassembly. See Preparing Your System for
Disassembly and Reassembly earlier in this chapter.
2. Remove the left-hand side access panel of the system chassis. See Removing
the Side Access Panel earlier in this chapter.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system.
3. Remove all the power cables from the system board, 5.25-inch devices,
diskette drive, and SCSI backplane.
4. Remove and save the nine screws that secure the power supply to the rear of
the chassis. See Figure 4-33.
A
A
A
Figure 4-33. Removing the Non-Hot-Swap Power Supply
5. Carefully remove the power supply from the chassis.
6. Follow this removal procedure in reverse order to install the replacement
power supply unit.
4-34 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Cooling Fan Unit
The optional front cooling fan unit contains up to two fans for cooling the CPU,
memory, and PCI devices built in the server.
Installation
1. Prepare your system for upgrade. See Preparing Your System for
Disassembly and Reassembly described earlier in this chapter.
2. Remove the left-hand side cover.
3. Hold the fan unit with its locking tab facing the front of the server and with
the hook facing the rear of the server. Insert the fan unit into the server. See
Figure 4-34.
Fan unit (Fan 5, for CPU and memory boards)
Locking tabs
Tabs
Fan unit (Fan 3, for PCI boards)
Figure 4-34. Installing a Fan Unit
Disassembly and Reassembly 4-35
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Insert the tabs into holes on the frame of the server, and push the cooling fan
unit toward the frame. See Figure 4-35.
Figure 4-35. Securing the Fan Unit
5. Connect the cooling fan cable to the system board. See Figure 4-36.
Fan Connectors
Figure 4-36. Fan cable Connector
6. Reassemble the removed components.
7. Configure the hardware by using the configuration disk supplied with the
optional fan unit. Refer to the manual that comes with the optional fan unit
for detailed instructions.
4-36 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal
1. Prepare your system for upgrade. See Preparing Your System for Upgrade
described earlier in this chapter.
2. Remove the left-hand side cover.
3. Remove the fan unit connector from the system board. See
Figure 4-37.
4. Push the locking tab to unlock the cooling fan unit, and remove the fan unit
from the server. See Figure 4-37.
5. Reassemble the removed components.
Figure 4-37. Removing a Fan Unit
Disassembly and Reassembly 4-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Removable 5.25-inch Media Devices
A variety of SCSI 5.25-inch removable media devices (i.e., tape backup, etc.)
can be installed in the four half-height media bays (Figure 4-38). The media
devices should be installed in the first available media bay from the top
(slot 1). Contact your sales representative or dealer for a list of approved
devices.
Slot 3
Slot 2
Slot 1
Figure 4-38. Removable Media Devices
IMPORTANT:
! With the standard configuration, the optional SCSI add-in card and
SCSI cable are required.
! The server can include a maximum of two half-height devices and one
full-height device.
! Set the SCSI termination of the 5.25-inch device to be installed to OFF
and the SCSI ID to a value which is not duplicated or corrupted with
that of any other device. Refer to the documentation coming with each
of the devices for how to set the values.
! For half-height device, first install a device in slot 1. Then install
another device in slot 2.
For full-height device, install the device to the slots 2 and 3.
! This system can include a maximum of two optional file devices.
4-38 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
1. Prepare your system for upgrade. See Preparing Your System for
Disassembly and Reassembly described earlier in this chapter.
2. Remove the side cover.
3. Remove the two screws fixing the dummy cover. See Figure 4-39.
4. Pull out the dummy cover toward you carefully.
NOTE: When installing a full-height device, remove two dummy covers.
Figure 4-39. Removing Dummy Covers
5. Attach the rails to the 5.25-inch device by using the four screws. See Figure
4-40.
Figure 4-40. Attaching the Rails
IMPORTANT: When installing a double-height device, use the DLT
device rails that is included with the server.
Disassembly and Reassembly 4-39
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Push the 5.25-inch device to the device bay carefully.
NOTE: Make sure the cables are not caught while the 5.25-inch device
is pushed into the slot.
7. Secure the device using the screws removed in step 3. See Figure 4-41.
Half-height device
Full-height device
Figure 4-41. Securing the Media Device
8. Ensure the front of the installed 5.25-inch device is aligned with the
CDROM drive already installed in the server.
9. Connect the SCSI interface and power cables to the installed 5.25-inch
device.
10.Install the removed components.
Removal
Remove the 5.25-inch device in the reverse procedure of the installation.
4-40 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
PCI Boards
The server contains six slots into which PCI boards can be inserted.
See Figure 4-42.
IMPORTANT: PCI boards are easily affected by static electricity.
Handle a PCI board after making your body contact with a metallic frame
section of the server to discharge the static electricity on your body. Do
not make bare hands contact with terminals and components on the PCI
board. In addition, do not put the PCI board on a desk directly. See
"Static Precautions" in this chapter for details of the static electricity.
NOTE: When a PCI board is installed, removed, or removed from the
present slot and then installed in another slot, modify the detailed settings
including the interrupt lines (IRQ) by using the BIOS setup utility SETUP if
necessary. See Chapter 4 for the settings of the interrupt line states and
I/O spaces at the shipment of the server.
PCI board slot #1
PCI board slot #2
64-bit/100 MHz *1
PCI board slot #3
PCI board slot #4
PCI board slot #5
PCI board slot #6
32-bit/33 MHz *2
System Board
Figure 4-42. PCI Slot Designations
*1 The system operates at the rate of 33 MHz when PCI boards operating only at 33 MHz are installed in these
slots.
*2 Do not install a set of PCI boards providing a specific function to extend over both the 64-bit and 32-bit PCI
buses.
Disassembly and Reassembly 4-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
IMPORTANT:
! For ease of installation, remove the external SCSI cable when
installing the full-length PCI card.
! 3.3V or universal PCI boards can be installed in PCI board slots #1 to
#4.
! 5V or universal PCI boards can be installed in PCI board slots #5 and
#6.
NOTE: To install a PCI board, make sure that the board connecting
section is engaged with the connector of the PCI board slot.
List of optional devices and their available slots
Slot
Board Name
Remarks
PCI PCI PCI PCI PCI PCI
#1 #2 #3 #4 #5 #6
SCSI Controller
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
√
√
–
SCSI Controller
Disk Array Controller
Disk Array Controller
Only N8103-80F and N8103-
81F can coexist.
–
–
Fibre Channel
Controller
Up to two Fibre channel
controllers can be installed.
√
√
100BASE-TX Board
100BASE-TX Board
100BASE-TX Board
Up to four 100BASE-TX
boards can be installed.
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
Up to two 100BASE-TX
boards can be installed.
√
√
√
√
1000BASE-T Board
Only one 1000BASE-T board
can be installed. (With AFT, up
to four boards can be
installed.)
√
√
√
√
√: Installation enabled, –: Installation disabled
4-42 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Prepare your system for upgrade. See Preparing Your System for
Disassembly and Reassembly described earlier in this chapter.
2. Remove the left-hand side cover.
3. Define the slot in which a board is installed and remove the connector cap of
the slot.
IMPORTANT: Keep the removed connector cap carefully.
4. Remove a screw securing the expansion slot cover.
5. Remove the expansion slot cover. See Figure 4-43.
IMPORTANT: Keep the expansion slot cover being removed carefully.
Figure 4-43. Removing the PCI Slot Cover
6. On the edge opposite the connectors, grasp the board by both corners. Orient
the board to the vacant slot so that the metal retention bracket is toward the
rear of the chassis.
7. Insert the board into the front retention mechanism and rear guide rails.
Carefully push the board until it engages and fully seats in the slot
connector.
IMPORTANT: If the board cannot be installed easily, remove the board
once and then reinstall it. Excess force added to the board may cause the
board to be broken.
Disassembly and Reassembly 4-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide rail
Figure 4-44. Installing a PCI Board
8. Secure the board with a screw removed in Step 4.
9. Reinstall the removed components.
10.Turn on the power of the server
11.Check for any POST error messages.
12.Start the BIOS Setup Utility to set the "Reset Configuration Data" in the
"Advanced" menu to "Yes". This is required to update the hardware
configuration information.
Removal
Remove the board in the reverse procedure of the installation. Then install the
connector cap and additional slot cover.
4-44 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Controller Board
The functions of a disk array controller are described in the following table.
Functions of a Disk Array Controller
Function
Description
Level
Support RAID levels RAID0, RAID1, RAID5, and RAID0+1.
Allows a hard disk to be replaced while the system is running depending on
RAID level and system configuration.
Hot plug
After the defected hard disk is replaced with a new one, the data saved in the
defected hard disk is automatically recovered from the data saved in the
remaining hard disks depending on RAID level.
Auto rebuild
Expand capacity
The addition of a hard disk without system interruption can automatically
expand the area in which disk arrays are available.
Please note the following when installing and configuring a disk array:
! Disk array controller boards are easily affected by static electricity.
Handle the disk array controller board only after making body contact
with the metallic frame section of the server chassis in order to discharge
the static electricity from your body. Also, never make contact with
terminals and components on the disk array controller board using your
bare hands.
! To change the disk array configuration or the RAID level, the hard disks
must be initialized. If important data is saved on the hard disks used to
constitute a disk array, first back up the data on the other hard disks and
then install the boards and configure the disk array.
! More than one hard disk is required to configure a disk array.
! Hard disks used in the disk array configuration should have the same
disk revolution rate and capacity.
! See PCI Board in this chapter for the slots in which a RAID Controller
can be installed.
! Up to four disk array controller boards can be installed in your server.
! Several RAID (Redundant Arrays of Independent Disks) levels can be
set for the newly installed disk array controller boards. For details of the
available RAID types, data transfer rate, and array configurations refer to
the online documentation on the EXPRESSBUILDER CD-ROM that
comes with your system or the vendor documentation that comes with
the disk array controller.
! The available capacity of the hard disks in the disk array configuration
will be lower than the capacity of the hard disks in a standard
configuration, but the disk reliability is much improved.
Disassembly and Reassembly 4-45
Download from Www.Somanuals.com. All Manuals Search And Download.
! Set "PCI SLOT n ROM (n: slot number)," a parameter of the slot in
which a hard disk is installed, to "Enable" in "PCI Configuration" on the
Advanced menu of the BIOS utility SETUP.
! Replacement of disk array controller board
Restore the disk array configuration information in the disk array
controller boards. Use the configuration utility for the restoration. Refer
to the online document saved in CD-ROM "EXPRESSBUILDER"
coming with the server or the documentation coming with the disk array
controller for details. If a disk array controller is replaced, create the
configuration information newly by using the proper utility.
! When more than one disk array controller board are installed in the
server, install the disk array controller board to which the system disk to
be booted is connected in the lowest PCI slot number. For example, if
four disk array controller boards are installed in PCI slots #1 to #4, the
system disk should be connected to the board installed in PCI slot #2.
PCI Slot Boot Priority
PCI Slot Number
Boot Priority
PCI slot #1
6
PCI slot #2
PCI slot #3
PCI slot #4
PCI slot #5
PCI slot #6
5
4
3
2
1
4-46 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Internal Disks in Disk Array Configuration
For the installation of the RAID controller board, see "PCI Board" and the
manual that comes with the RAID controller board. The DISK access lamp on
the front panel of the server indicates the access status of the hard disk drive
connected to the RAID controller board. Before the access status can be
indicated, the LED connector on the RAID controller board and the DAC LED
connector on the system board must be connected through the LED cable
supplied with the server. The DAC LED connector is at the position shown in
the Figure 4-45 below. It can be connected in either direction.
To the mother board
Face this side
upward.
To the RAID
controller
LED cable
DAC LED connector
Figure 4-45. DAC LED Cable Connection to the System Board.
Disassembly and Reassembly 4-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Diskette Drive and Carrier Assembly
Your server system contains a 3.5-inch diskette drive housed in a carrier located
inside the front of the server chassis.
To remove the diskette drive and carrier assembly, perform the following
procedures:
1. Prepare your system for disassembly. See Preparing Your System for
Disassembly and Reassembly earlier in this chapter.
2. Remove the left-hand side access panel of the system chassis following
procedures previously described in this chapter.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system.
3. Disconnect the data cable connector and power cable connector from their
mating connectors on the rear of the diskette drive.
4. Remove and save the two screws (A) that secure the diskette drive carrier to
the front of the chassis. See Figure 4-46.
5. Slide the drive carrier towards the rear of the chassis, until it comes free and
place it on an antistatic surface.
A
A
Figure 4-46 . Removing the Diskette Drive and Carrier Assembly
6. Remove the four screws (C) that attach the drive (A) to the carrier (B). See
Figure 4-47. Save the screws for reassembly.
4-48 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Remove the drive from the carrier.
A
B
C
A
B
C
Diskette drive
Carrier
Screws (4)
Figure 4-47. Removing the Diskette Drive from the Carrier Assembly
8. Install the replacement diskette drive into the carrier and secure it with the
four screws removed in Step 6. See Figure 4-47.
9. Position the diskette drive carrier next to the hard disk drive bay and slide
the carrier towards the front of the system until it locks into place. Secure
the drive to the front panel using the two screws removed in Step 4.
See Figure 4-46.
10.Connect the data cable connector and power cable connector to the rear of
the diskette drive.
11.Reassemble all other removed components.
Disassembly and Reassembly 4-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Bezel and Front Bezel Hinge (Tower-
Based System)
Your server system contains a front bezel that covers the front of the chassis.
The bezel is secured to the front of the chassis by metal pins located at the top
and bottom of a front bezel hinge. To remove the front bezel, the two metal pins
must be removed from the bezel hinge.
To remove the front bezel and front bezel hinge (see Figure 4-48 and
Figure 4-48), perform the following procedures:
1. Prepare your system for disassembly. See Preparing Your System for
Disassembly and Reassembly earlier in this chapter.
2. Remove the metal pin (B) from the top of the bezel hinge (D) by pushing in
on the flexible bezel pin tab (C) and pulling the pin down and out of the
bezel hinge. See Figure 4-48.
3. Allow the bezel (A) to drop down so that it disengages from the bottom of
the bezel hinge and remove the bezel.
4. Remove the metal pin from the bottom of the bezel. Remove the front bezel.
A
B
D
C
A
B
C
Front bezel
Metal pin
Flexible bezel pin
tab
D
Bezel hinge
Figure 4-48. Removing the Front Bezel
4-50 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Remove the four screws securing the bezel hinge to the chassis and remove
the hinge. See Figure 4-49.
A
B
A
B
Screws (4)
Bezel hinge
Figure 4-49. Removing the Front Bezel Hinge
6. Install the replacement bezel hinge using the four screws removed in Step 5.
7. Align the front bezel with the bezel hinges and install the metal pins into the
top and bottom slots in the bezel hinge.
Front Panel
Your server system contains a front panel that houses the system controls and
indicators. You must open the front bezel to access the front panel. The front
panel is secured to the front of the chassis by hooks and a locking lever. To
remove the front panel its locking lever must be released and the panel moved
up slightly to disengage its hooks from the chassis.
To remove the front panel (see Figure 4-50), perform the following procedures:
1. Prepare your system for disassembly. See Preparing Your System for
Disassembly and Reassembly earlier in this chapter.
2. Remove the left-hand side access panel of the system chassis following
procedures previously described in this chapter.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system.
Disassembly and Reassembly 4-51
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Remove the front panel (A) by releasing its locking lever (B) and then
sliding the front panel up to disengage its hooks from the chassis. The
locking lever is located at the back of the front panel and is released by
pushing the lever towards the right so that it clears the notch in its locking
slot.
4. Pull the front panel (A) away from the front of the chassis far enough to
remove the five LEDs inserted into the back of the front panel. Note the
position of each LED before removing it from the front panel. Set the front
panel aside for reattaching it later.
A
B
A
B
Front panel
Locking lever
Figure 4-50. Removing the Front Panel
4-52 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot-Swap HDD Bay
This procedure describes how to remove the Hot-Swap SCSI Hard Disk Drive
(HDD) Bay that is housed in the front of your system.
!
WARNING
Before doing these procedures, make sure that your system
is powered off and unplug all AC power cords. Failure to
disconnect power before opening your system can result in
personal injury and equipment damage. All voltage is
removed only when the power cords are unplugged.
To remove the hot-swap HDD bay (see Figure 4-51), perform the following
procedures:
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Prepare your system for upgrade. See Preparing Your System for
Disassembly and Reassembly described earlier in this chapter.
3. Remove the left-hand side access panel as described earlier in this chapter.
4. Remove the optional front cooling fan unit if installed following procedures
described earlier in this chapter.
5. Remove all the drive carriers from the HDD bay. To remove a drive carrier
perform step 3 of Swapping a Hard Disk Drive described earlier in this
chapter.
6. Remove and save the eight screws securing the HDD bay to the front of the
chassis. See Figure 4-51.
7. Tag and disconnect the power cables, HSBP (I2C) cable, and SCSI interface
cable from their connectors on the SCSI backplane. The SCSI backplane is
located on the rear of the HDD bay.
8. Remove the HDD bay from the chassis.
Disassembly and Reassembly 4-53
Download from Www.Somanuals.com. All Manuals Search And Download.
A
A
A
A
Figure 4-51. Removing the HDD Bay
Hot-Swap SCSI Backplane
This procedure describes how to remove the hot-swap SCSI backplane that is
attached to the back of the hot-swap HDD bay.
!
WARNING
Before doing these procedures, make sure that your system
is powered off and unplug all AC power cords. Failure to
disconnect power before opening your system can result in
personal injury and equipment damage. All voltage is
removed only when the power cords are unplugged.
To remove the hot-swap SCSI backplane, perform the following procedures:
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Remove the hot-swap HDD bay. See Hot-Swap HDD Bay described in the
previous section.
3. Remove and save the eight screws securing the SCSI backplane to the rear
of the hot-swap HDD bay. See Figure 4-52.
4-54 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
A
B
C
Hot-swap HDD bay
Hot-swap SCSI backplane
Screws (8)
Figure 4-52. Removing the SCSI Backplane Bracket
4. Carefully pull the SCSI backplane straight out from the HDD bay and place
the backplane on an antistatic wrapper.
5. Carefully position the replacement SCSI backplane on to the rear of the
HDD bay and secure it with the eight screws removed in Step 3. See Figure
4-52.
6. At the front of the server, install the HDD bay into the chassis and secure it
with eight screws. See Figure 4-51.
7. Connect the power cables, HSBP (I2C) cable, and SCSI interface cable to
their connectors on the SCSI backplane.
8. Install the optional front cooling fan unit following procedures previously
described in this chapter, if previously removed.
9. Install the left-hand side access panel as described earlier in this chapter.
10.Install all the drive carriers into the HDD bay.
Disassembly and Reassembly 4-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Rear Cooling Fan
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Open the front bezel of your system's cabinet.
3. Shutdown the operating system (OS).
4. Press the power on/off switch on the front panel of the server (see
Front View in Chapter 1). The power-on LED goes out.
5. Power off the peripheral devices.
6. Unplug the system power cord(s) from the AC wall outlet(s).
Note: If the system power cord is connected to a power
control unit such as an UPS (Uninterruptible Power Supply),
refer to the UPS user's guide for proper power-off
procedures.
7. Remove the left-hand side access panel of the chassis following procedures
previously described in this chapter.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system.
8. Remove the processor air duct. See Processor Air Duct Removal earlier in
this chapter.
9. Disconnect the rear cooling fan cable to the system board. See Figure 4-53.
Fan Connector
Figure 4-53. Rear Cooling Fan System Board Connector
4-56 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
10.To release the fan from the fan housing, pull the fan housing tab
(Figure 4-54, A) towards you until the tab clears the edge of the fan. Swivel
the fan towards the front of the server and remove it from the fan housing.
B
A
Figure 4-54. Removing the Rear Cooling Fan
11.Position the replacement fan inside the fan housing, ensuring the fan label
faces the rear of the system. Install the side of the fan nearest the system
board first, then swivel the outside edge of the fan in place inside the fan
housing tab.
12.Connect the rear cooling fan cable to the system board.
See Figure 4-53.
13.Reassemble all removed components.
Disassembly and Reassembly 4-57
Download from Www.Somanuals.com. All Manuals Search And Download.
System Board
To remove the system board all the processor(s), DIMMs, and PCI option
boards (if installed) on the board must be removed and all system board cable
connectors tagged and unplugged.
!
CAUTION
The system board can be extremely sensitive to ESD and
always requires careful handling. After removing it from the
system, place it component-side up on a nonconductive,
static-free surface to prevent shorting out the battery leads.
Do not slide the system board over any surface.
To remove the system board, perform the following procedures:
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Open the front bezel of your system.
3. Shutdown the operating system (OS).
4. Press the power on/off switch on the front panel of the server (see
Front View in Chapter 1). The power-on LED goes out.
5. Power off the peripheral devices.
6. Unplug the system power cord(s) from the AC wall outlet(s).
Note: If the system power cord is connected to a power
control unit such as an UPS (Uninterruptible Power Supply),
refer to the UPS user's guide for proper power-off
procedures.
7. Remove the left-hand side access panel of the system chassis following
procedures previously described in this chapter.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system.
8. Remove the processor air duct. See Processor Air Duct Removal earlier in
this chapter.
9. Remove the rear cooling fan following procedures described in the previous
section.
10.Perform the processor(s) and DIMM(s) removal procedures described earlier
in the section Modifying the System Board. Save the processor(s) and
DIMM(s) for reassembly.
4-58 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
11.Tag and remove any PCI option boards installed on the system board. See
PCI Boards earlier in this chapter. Save the PCI option boards for
reassembly.
Note: The PCI option boards must be reinstalled in the
same slots when you reassemble the system.
12.Tag and disconnect all the power, signal, and fan cable connectors from their
mating connectors on the system board.
13.Remove the eight screws securing the system board to the chassis.
See Figure 4-55, A. Save the screws for reassembly.
14.Carefully move the board sideways slightly towards the front of the cabinet
so that it clears all its I/O connectors. Then lift the system board out of the
chassis and place it component-side up on a nonconductive, static free
surface.
15.Remove the four screws securing each CPU retention module and remove
the module for use on the replacement system board. See Figure 4-55, B.
Note that the CPU retention module reinforcement brackets are located on
the back of the system board and will become loose once the screws are
removed.
B
A
C
A
B
C
System board mounting
screws (8)
CPU retention module
mounting screws (4)
System Board
Figure 4-55. Removing the System Board and Retention Modules
Disassembly and Reassembly 4-59
Download from Www.Somanuals.com. All Manuals Search And Download.
16.Install the two retention modules to the system board using the screws
removed in Step 15.
17.Install the replacement system board into the server securing it with the eight
screws removed in Step 13.
18.Connect all the power, signal, and fan cable connectors to their mating
connectors on the system board.
19.Perform the processor(s) and DIMM(s) installation procedures described
earlier in the section Modifying the System Board.
20.Install any PCI option boards removed from the system board. See PCI
Boards earlier in this chapter.
21.Install the rear cooling fan following procedures previously described in this
chapter.
22.Install the processor air duct following procedures previously described in
this chapter.
23.Reassemble any other removed components and check system board
operation..
Power Supply Back Board
To remove the power supply back board, perform the following procedures:
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Open the front bezel of your system.
3. Shutdown the operating system (OS).
4. Press the power on/off switch on the front panel of the server (see
Front View in Chapter 1). The power-on LED goes out.
5. Power off the peripheral devices.
6. Unplug the system power cord(s) from the AC wall outlet(s).
Note: If the system power cord is connected to a power
control unit such as an UPS (Uninterruptible Power Supply),
refer to the UPS user's guide for proper power-off
procedures.
7. Remove the system left-hand side access panel following procedures
previously described in this chapter.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side access panel removed. Always replace the
panel before powering on the system
4-60 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Remove any power supply installed in the system following procedures
described earlier it this chapter.
9. Figure 4-56, A shows the location of the power supply back board. Tag and
remove all power supply back board cables connected to the system board,
SCSI backplane, and peripheral devices installed in the system.
B
A
A
B
Power Supply Back Board
Power Supply Back Board
Thumbscrew
Figure 4-56. Removing the Power Supply Back Board
10.Loosen the single thumbscrew securing the power supply back board to the
system chassis. See Figure 4-56, B.
11.The power supply back board mounts on top of four standoffs. Pull the back
board towards you to release it from the standoffs.
12.Lift the power supply back board towards the top of the system and remove
it and associated cables from the system.
13.Install the replacement power supply back board into the system in the same
position as the original being sure to route the power cables to the system
board, SCSI backplane and internal peripheral components.
14.Push the back board away from you to secure it to the standoffs.
15.Tighten the single thumbscrew securing the power supply back board to the
system chassis. See Figure 4-56, B.
16.Install any power supply removed in Step 8.
17.Install any other components removed in this procedure and power up the
system.
Disassembly and Reassembly 4-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Tower Feet
Your tower system has four stabilizer feet located on the bottom of the chassis.
To remove the stabilizer feet you must have the chassis positioned on its side
with its stabilizer feet overhanging the edge of a table or workbench.
To remove the tower feet (see Figure 4-57), perform the following procedures:
1. Prepare your system for disassembly. See Preparing Your System for
Disassembly and Reassembly earlier in this chapter.
2. Position the chassis on it side and move it to the edge of a table or
workbench so that its stabilizer feet overhang the surface rim.
3. Remove and save the two screws attaching a foot to the bottom of the
chassis.
4. Slide the foot towards the rear of the chassis and remove the foot from the
chassis.
5. Repeat steps 3 and 4 to remove the other feet from the chassis.
A
B
C
A
B
C
Chassis foot
Screws (2 per foot)
Work surface
Figure 4-57. Removing the Tower Feet
4-62 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
I/O Shield
To remove the I/O, perform the following procedures:
1. Observe the safety and ESD precautions listed under General Information
and Static Precautions at the beginning of this chapter.
2. Open the front bezel of your system.
3. Shutdown the operating system (OS).
4. Press the power on/off switch on the front panel of the server (see
Front View in Chapter 1).
5. Power off the peripheral devices.
6. Unplug the system power cord(s) from the AC wall outlet(s).
Note: If the system power cord is connected to a power
control unit such as an UPS (Uninterruptible Power Supply),
refer to the UPS user's guide for proper power-off
procedures.
7. Remove the left-hand side access panel of the system chassis following
procedures previously described in this chapter.
8. Remove the system board following procedures previously described in this
chapter.
9. The I/O shield snaps into the rear panel. To remove the I/O shield, push in
on the perimeter of the shield towards the inside of the chassis.
See Figure 4-58, A for the location of the I/O shield.
A
Figure 4-58. Removing the I/O shield
Disassembly and Reassembly 4-63
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Snap the replacement I/O shield into place in the rear panel.
11.Install the system board following procedures previously described in this
chapter.
12.Install the left-hand side access panel.
LED/Switch Assembly
Your server system contains a front panel that houses the LED/switch assembly.
You must open the front bezel to access the front panel. To remove the front
panel LED/switch assembly, perform the following procedures:
1. Prepare your system for disassembly. See Preparing Your System for
Disassembly and Reassembly earlier in this chapter.
2. Remove the left-hand side access panel of the system chassis following
procedures previously described in this chapter.
3. Remove the front panel following procedures previously described in this
chapter. See Front Panel earlier in this chapter.
4. Remove the power switch, reset switch and dump switch from the front of
the chassis. To release these switches, squeeze their two plastic snap tabs
together and slide the switch back until it is free of the chassis.
See Figure 4-59, A.
A
B
C
A
B
C
Switches (3)
Cable
System Board Connector
Figure 4-59. Replacing the LED/Switch Assembly
4-64 Disassembly and Reassembly
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Tag and disconnect the LED/Switch Assembly cable (Figure 4-59, B) from
its mating connector on the system board. See Figure 4-59, C. Carefully
remove the LED/Switch assembly from the system.
Intrusion Switch Assembly
Your server system includes two chassis intrusion switches that are located on
the front and rear of the system chassis. The switches monitor the front door
being opened and the left-hand side access panel being removed. To access the
two intrusion switches you must remove the left-hand side access panel from the
system chassis.
Note: The intrusion switch assembly consists of two
intrusion switches with cables and a single cable connector.
To remove the intrusion switch assembly (see Figure 4-60), perform the
following procedures:
1. Prepare your system for disassembly. See Preparing Your System for
Disassembly and Reassembly earlier in this chapter.
2. Remove the left-hand side access panel of the system chassis. See Removing
the Side Access Panel earlier in this chapter.
3. Tag and disconnect the intrusion switch cable from its mating connector on
the system board. See Figure 4-60, C.
4. Remove the intrusion switch located on the front and the switch located at
the rear of the chassis. See Figure 4-60, A and B. To release an intrusion
switch squeeze its two plastic snap tabs together and slide it back until it is
free of the chassis.
5. Carefully remove the intrusion switch assembly.
A
B
C
A
B
C
Rear Intrusion Switch
Front Intrusion Switch
System Board Connector
Figure 4-60. Removing the Intrusion Switch Assembly
Disassembly and Reassembly 4-65
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Problem Solving
! Problem Solving
! Static Precautions
! Resetting the Server
! Forced Shutdown
! Troubleshooting Checklists
! Diagnostic Procedures
! Specific Problems and Corrective Actions
! Problems with the Network
! Plug and Play Installation Tips
! Error Messages
! How to Identify BIOS and BMC Revision Levels
! Lamps
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem Solving
This chapter helps you identify and solve problems that may occur during system
installation or while using your system. The first section of this chapter tells you how to
reset your system in the event of problems. The next few sections provide
troubleshooting checklists and procedural steps that help you isolate specific system
problems. The last section includes BIOS and system user information.
!
WARNING
The DC push-button on/off switch on the front panel does not turn off
the system AC power. Also, +5vdc is present on the system board
whenever the AC power cord is connected between the system and
an AC outlet. Before doing the procedures in this manual, make sure
that your system is powered off and unplug the AC power cords from
the back of the chassis. Failure to disconnect power before opening
your system can result in personal injury and equipment damage
!
CAUTION
Operating your system with the cover removed can damage your
system components. For proper cooling and airflow, always replace
the top panel before powering on your system.
Static Precautions
An electrostatic discharge (ESD) can damage disk drives, option boards, and other
components. You can provide some ESD protection by wearing an antistatic wrist strap
attached to chassis ground when handling system components.
Electronic devices can be easily damaged by static electricity. To prevent damage, keep
them in their protective packaging when they are not installed in your system.
5-2 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Resetting the Server
There are two ways to reset the server.
IMPORTANT: Resetting the server clears the DIMM memory and the data in
process. To reset the server when it is not frozen, make sure that no processing is
in progress.
! Hard reset
Press the RESET switch at the front of the server. See Figure 5-1.
Figure 5-1. Pressing the Reset Button
! Soft reset
If the server halts before starting the OS, press and hold Ctrl and Alt and press Delete.
This restarts the server.
Problem Solving 5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Forced Shutdown
Use this function when an OS command does not shut down the server, the POWER
switch does not turn off the server, or resetting does not work.
Press and hold the POWER switch on the server for at least four seconds. The power is
forcibly turned off. To turn on the power back again, wait approximately 10 seconds
after turning off the power (forced shutdown).
Press here for at
least 4 seconds.
Figure 5-2. Pressing the Power Button
IMPORTANT: If the remote power-on function is used, cycle the power once to
load the OS, and turn off the power again in the normal way.
5-4 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Checklists
The following subsections provide troubleshooting checklists for problems that occur at
initial system startup, when you run new application software, and after the system
hardware and software have been running correctly.
Initial System Startup
Incorrect installation or configuration usually causes problems that occur at initial
system startup. Hardware failure is a less frequent cause. If you have problems during
initial system startup, check the following:
! Are the system power cords properly connected to the system and plugged into a
NEMA 5-15R outlet (100-120 VAC), a NEMA 6-15R outlet (200-240 VAC), or an
UPS that meets the power specifications of the system?
! Is AC power available at the wall outlet?
! Is the system cover closed properly? A power interlock switch detects if the cover is
open. If the cover is not closed properly, power is not supplied to the server system.
! Is the power on/off push-button switch on the front panel in the ON position (power
on LED should be lit)?
! Are all cables correctly connected and secured?
! Are all the PCI option boards fully seated in their connector slots in the riser cards?
! Are all jumpers and switch settings on option boards and peripheral devices correct?
If applicable, ensure that there are no conflicts; for example, two option boards
sharing the same interrupt.
! Are the processors fully seated in their slots on the system board? Refer to the
Processors subsection of Upgrading Your System in Chapter 4 for installation
instructions?
! Are all DIMMs fully seated and installed correctly? Refer to the DIMMs subsection
of Upgrading Your System in Chapter 4 for installation instructions.
! Are all option boards and disk drives installed correctly? Refer to the Options
Boards and Hard Disk Drives subsections of Upgrading Your System in Chapter 4
for installation instructions.
! Is the system hard disk drive properly formatted or defined?
! Is the operating system properly loaded? Refer to the operating system
documentation.
! Are all drivers properly installed?
! Are the configuration settings in BIOS Setup and the SCSISelect Utility correct? For
information about running these utilities, refer to the Configuring Your System in
Chapter 3.
Problem Solving 5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
If the above items are all correct, but the problem reoccurs, refer to Additional
Troubleshooting Procedures in this chapter.
Running New Application Software
Problems that occur when you run new application software are usually related to the
software. Faulty equipment is much less likely, especially if other software runs
correctly. If you have problems while running new application software, check the
following:
! Does the system meet the minimum hardware requirements for the software? Refer
to the software documentation.
! Is the software an authorized copy? Unauthorized copies often do not work. Obtain
an authorized copy of the software.
! If you are running the software from a diskette, is it a good copy?
! If you are running the software from a hard disk drive, is the software correctly
installed? Where all necessary procedures followed and files installed?
! If you are running the software from a CD-ROM disk is the disk scratched or dirty?
! Are the correct device drivers installed?
! Is the software correctly configured for the system?
! Are you using the software correctly?
! If other software runs correctly on the system, contact your vendor about the failing
software.
If the problems persist with the software, contact the software vendor's customer service
representative.
5-6 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
After System Has Been Running Correctly
Problems that occur after the system hardware and software have been running
correctly often indicate equipment failure. However, many situations that are easy to
correct can also cause such problems. If you have problems after the system has been
running correctly, check the following:
! If you are running the software from a diskette or CD-ROM, try a new copy of the
software.
! If you are running the software from a hard disk drive, try running it from a floppy.
If the software runs correctly, there may be a problem with the copy on the hard
disk. Reinstall the software on the hard disk drive and try running it again. Make
sure all the necessary files are installed.
! If the problem recurs, you may need to reformat the hard disk drive. The hard disk
drive, the drive controller, or the system board set may be defective.
! If the problems are intermittent, there may be a loose cable, dirt in the keyboard (if
keyboard input is incorrect), a marginal power supply, or other random component
failures.
! If you suspect that a transient voltage spike, power outage, or brownout might have
occurred, reload the software and try running it again. Symptoms of voltage spikes
include a flickering video display, unexpected system reboots, and the system not
responding to user commands.
Note: Voltage spikes can corrupt or destroy data files on the
drive. If you are experiencing voltage spikes on the power line, install
a surge suppresser between the power outlet and the system power
cord.
If the problem recurs after you have checked and corrected all of the above items, refer
to Diagnostic Procedures in this chapter.
Problem Solving 5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostic Procedures
This section provides a more detailed approach to diagnosing and identifying problems
and then locating their sources.
Error Checking
Each time you turn on the system, POST (Power-On-Self-Test) runs automatically and
checks the system board, processors, memory board, keyboard, and mouse.
If POST finds an error, it displays an error message. Refer to the Error Message section
in this chapter for an explanation of each error message.
Troubleshooting Guide
Use the following troubleshooting procedures to help you identify a problem. These
general procedures lead you through the following:
! Preparing the system for diagnosing problems
! Monitoring POST while it is running
! Verifying proper operation of key system LEDs
! Confirming loading of the operating system.
Preparing the System for Diagnosing Problems
To prepare the system for diagnosing problems, perform the following:
Note: Before disconnecting any peripheral cables from the
system, turn off the system and any external peripheral devices.
Failure to do so can cause permanent damage to the system and/or
the peripheral devices.
1. Turn off the system and all external peripheral devices. Disconnect all devices from
the system except the keyboard and video monitor.
2. Make sure the system power cords are plugged into a properly grounded AC outlet.
3. Make sure your video display monitor and keyboard are correctly connected to the
system. Turn on the video monitor. Set its brightness and contrast controls to at least
two-thirds of their maximum ranges (refer to the documentation supplied with your
video display monitor).
4. If the operating system normally loads from the hard disk drive, make sure there is
no diskette in drive A. Otherwise, place a diskette containing the operating system
files in drive A.
5. Turn on the system. If the power indicator LED does not light, refer to Power Light
Does Not Light found later in this chapter.
5-8 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring POST
Each time you turn on the system, the Power-On Self-Test (POST) runs automatically
and checks the system board, processors, memory board, keyboard, and mouse.
During the memory test, POST displays the amount of memory that it is able to access
and test. Depending on the amount of memory, it may take several minutes to complete
the memory test. When the memory test completes, the following is displayed:
Press <F2> to enter SETUP
Press <F2> to enter BIOS SETUP. When the utility appears, follow the instructions on
your monitor to configure BIOS. See Chapter 3, "Configuring Your System." If you do
not press <F2>, the above message remains for a few seconds and the boot process
continues.
When this message appears:
Press <Ctrl> <A> for SCSISelect™ Utility!
Press <Ctrl+A> if you want to configure SCSI devices in your system. When the utility
appears, follow the instructions on your monitor to configure the SCSI host adapter
settings and run the SCSI disk utilities. See Chapter 3, Configuring Your System. If you
choose not to run SCSISelect™ Utility, the boot process continues.
If POST finds an error, it displays an error message and, in case there is a problem with
the display, it emits a series of long and short beeps. Write down any beep code
emitted. This information is useful to your service representative.
Refer to the “Error Messages” section in this chapter for a list of items to check for each
error code and for an explanation of the error beep codes.
The POST Tests table at the end of this chapter lists keys active during POST and
provides a description of errors that may occur.
The BIOS indicates errors by writing an error code to the PS/2-standard logging area in
the Extended BIOS Data Area, and by displaying a message on the screen, which is
sometimes preceded by the POST Error Code. The error code will also be logged to the
Event Logging area.
Report any error code to your service representative.
POST Keys and Errors
Action/Message
Description
If POST Beeps Before
Video Appears
Initialization failed before video initialized. Most beep code
errors are fatal; initialization cannot continue. Refer to the
section “Error Messages” in this chapter.
Note error; press F1 to continue boot or F2 to enter Setup.
Refer to the section “Error Messages” in this chapter.
If Monitor Displays Error
To Enter Setup
Setup changes specific options, then writes to CMOS,
NVRAM. Press F2 during initialization to run Setup. If you do
not press F2, the boot process continues.
Enter BOOT Diskette
If prompted, insert the boot diskette.
Problem Solving 5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Verifying Proper Operation of Key System Indicators
As POST determines the system configuration, it tests for the presence of each mass
storage device installed in the system. As each device is checked, its activity indicator
should turn on briefly. Check for the following:
! Does the diskette drive activity indicator turn on briefly? If not, refer to “Diskette
Drive Activity Indicator Does Not Light” in this chapter.
! If there is a hard disk drive or SCSI devices installed in the system, does the hard
disk drive activity indicator turn on briefly? If not, refer to Hard Disk Drive Activity
Indicator Does Not Light in this chapter.
Confirming Loading of the Operating System
Once the system boots up, the operating system prompt appears on the screen. The
prompt varies according to the operating system. If the operating system prompt does
not appear, refer to Problems with Application Software found later in this chapter.
5-10 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Specific Problems and Corrective Actions
This section provides possible solutions for the following specific problems:
! Power LED does not light
! No beep or incorrect beep pattern
! No characters appear on screen
! Characters on the screen appear distorted or incorrect
! System cooling fan does not rotate
! Diskette drive activity LED does not light
! Hard disk drive activity LED does not light
! CD-ROM drive activity LED does not light
! Problems with application software
! The startup prompt “Press <F2> key if you want to run Setup” does not appear on
the screen.
! The bootable CD-ROM is not detected.
Try the solutions in the order given. If you cannot correct the problem, contact your
service representative for assistance.
Power LED Does Not Light
Check the following:
! Is the system operating normally? If so, the power LED is probably defective.
! Are there other problems with the system? If so, check the items listed under System
Cooling Fans Do Not Rotate.
Incorrect or No Beep Code
Check the following:
! Is the speaker operating?
If the system operates normally, but there was no beep, the speaker may be defective,
contact your service representative for assistance.
Record the beep code emitted by POST, and see the “Messages and Beep Codes”
section found later in this chapter.
Problem Solving 5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
No Characters Appear on Screen
Check the following:
! Is the keyboard working? Check to see if the Num Lock light is functioning.
! Is the video display monitor plugged in and turned on?
! Are the brightness and contrast controls on the video monitor properly adjusted?
! Are the video monitor switch settings correct?
! Is the video monitor signal cable properly installed?
! Is the onboard video controller enabled?
If you are using a video controller board, verify that the video controller board is fully
seated in its connector
If there are still no characters on the screen after you reboot the system, contact your
service representative or authorized dealer for assistance.
POST emits one long beep and two short beeps pattern to indicate a possible problem
with the video display controller. If you do not receive a beep pattern and characters do
not display, the video display or video controller may have failed. Contact your service
representative or authorized dealer for assistance.
Characters are Distorted or Incorrect
Check the following:
! Are the brightness and contrast controls properly adjusted on the video display?
Refer to the documentation supplied with your video display.
! Are the video monitor's signal and power cables properly installed?
! If the problem persists, the video monitor may be faulty or it may be the incorrect
type. Contact your service representative for assistance.
System Cooling Fans Do Not Rotate
Check the following:
! Is AC power available at the wall outlet?
! Are the system power cords properly connected to the power supplies and the AC
wall outlets?
! Is the cooling fan module power connectors seated properly?
! Is the front panel power on indicator lit?
If the switches and connections are correct and the power outlet is functioning, the
power supply has probably failed. Contact your service representative for assistance.
5-12 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Diskette Drive Activity LED Does Not Light
Check the following:
! Is the diskette drive properly configured?
! Is the CDROM/Floppy Disk Drive combo properly installed in the flex bay?
Use BIOS Setup to make sure that the diskette drive controller is set to Enabled. For
information about running BIOS Setup, refer to the Configuring Your System chapter.
If the problem persists, there may be a problem with the diskette drive, system board, or
drive signal cable. Contact your service representative for assistance.
CD-ROM Drive Activity Light Does Not Light
Check the following:
! Is the CDROM/Floppy Disk Drive combo properly installed in the flex bay?
! Are all relevant switches and jumpers on the drive set correctly?
! Is the drive properly configured?
! Is the onboard IDE controller enabled?
Problems with Application Software
If you have problems with application software, perform the following:
! Verify that the software is properly configured for the system. Refer to the software
installation and operation documentation for instructions on setting up and using the
software.
! Verify a different copy of the software to see if the problem is with the copy that you
are using.
! Make sure all cables are installed correctly.
! Verify that the system board jumpers are set correctly. Refer to the Configuring Your
System chapter for jumper settings.
! If other software runs correctly on the system, contact your vendor about the failing
software.
If the problem persists, contact the software vendor's customer service representative
for assistance.
Problem Solving 5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Bootable CD-ROM Is Not Detected
Check the following:
! Is the BIOS set to allow the CD-ROM to be the first bootable device? Check your
BIOS Setup (F2) configuration.
Problems with the Network
Diagnostics pass, but the connection fails:
! Make sure the network cable is securely attached.
The controller stopped working when an add-in adapter was installed:
! Make sure the cable is connected to the port from the onboard network controller.
! Make sure the other adapter supports shared interrupts.
! Try reseating the add-in adapter.
The add-in adapter stopped working without apparent cause.
! Try reseating the adapter first; then try a different slot if necessary.
! The network driver files may be corrupt or deleted. Delete and then reinstall the
drivers.
! Run the diagnostics.
Plug and Play Installation Tips
Certain drivers may require interrupts that are not shared with other PCI drivers. The
BIOS Setup Utility can be used to adjust the interrupt numbers for PCI devices. For
certain drivers, it may be necessary to alter settings so that interrupts are not shared.
5-14 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
This section describes the POST error codes and messages.
POST Error Codes and Messages
Whenever a recoverable error occurs during POST, BIOS displays a message on the
video display screen and causes the speaker to beep as the message appears. BIOS also
issues a beep code (one long tone followed by two short tones) during POST if the
video configuration fails or if an external ROM module does not have the correct
checksum. The BIOS indicates errors by writing an error code to the PS/2-standard
logging area in the Extended BIOS Data Area, and by displaying a message on the
screen, which is sometimes preceded by the POST Error Code. The error code will also
be logged to the Event Logging area.
Table 5-1 POST Error Codes and Messages is a list of the error codes and messages
written at the start of each POST test. Table 5-2 POST Error Beep Codes is a list of
beep codes issued for each POST test. The devices associated with the POST error
codes are shown in subsection POST Error Code Hardware References that follow.
Table 5-1. POST Error Codes and Messages
On-screen error message
Action
100
101
102
103
104
Timer Channel 2 Error
Master Interrupt Controller
Slave Interrupt Controller
CMOS Battery Failure
CMOS Option not Set
Contact your service representative to replace the system
board.
Contact your service representative to replace the system
board. (Restart the computer, and then execute SETUP to
correct the setting.)
105
106
CMOS/GPNV Checksum Bad
CMOS Display Error
Execute SETUP to correct the setting.
Contact your service representative to replace the system
board.
107
108
109
Insert Key Pressed
Release the key.
Keyboard Locked Message
Keyboard Stuck Key
Reconnect the keyboard.
Release the key. Try a different keyboard.
If the problem persists, contact your service representative
to replace the system board.
10A
10B
Keyboard Interface Error
System Memory Size Error
Reconnect the keyboard. Try a different keyboard.
If the problem persists, contact your service
representative to replace the system board.
Install the DIMMs correctly.
Check if all the installed DIMMs are the same specification.
Contact your service representative to replace the DIMMs.
Problem Solving 5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1. POST Error Codes and Messages (continued)
On-screen error message
Action
10E
External Cache Failure
Install the CPU (processor) correctly.
Contact your service representative to replace the CPU.
110
111
112
113
114
115
116
117
118
119
11A
11B
11E
Floppy Controller Error
Floppy A: Error
Contact your service representative to replace the floppy
disk drive or system board. This server does not support
floppy disk drive B.
Floppy B: Error
Hard disk 0 Error
Contact your service representative to replace the system
board, SCSI back-plane, or hard disk.
Hard disk 1 Error
Hard disk 2 Error
Contact your service representative to replace the system
board, SCSI back-plane, or hard disk.
Hard disk 3 Error
CD-ROM disk 0 Error
CD-ROM disk 1 Error
CD-ROM disk 2 Error
CD-ROM disk 3 Error
Date/Time not set
Cache memory bad
Contact your service representative to replace the system
board or the CD-ROM drive.
Activate the BIOS SETUP utility to set the date and time.
Install the CPU (processor) correctly.
Contact your service representative to replace the CPU.
120
121
NVRAM cleared by Jumper
Password clear
Activate the BIOS SETUP utility to set the CMOS or
password.
140
141
142
143
144
PCI Error
Securely install the PCI boards and PCI riser card.
PCI Memory Allocation Error
PCI IO Allocation Error
PCI IRQ Allocation Error
Shadow of PCI ROM Failed
Contact your service representative to replace the PCI
board, system board, or PCI riser card.
Activate the BIOS SETUP utility to set the PCI board.
Securely install the PCI boards and PCI riser card.
Contact your service representative to replace the PCI
board, system board, or PCI riser card.
145
146
PCI ROM not found
Securely install the PCI boards and PCI riser card.
Contact your service representative to replace the PCI
board, system board, or PCI riser card.
Insufficient Memory to Shadow For PCI boards which do not need to be bootable, activate
PCI ROM
the BIOS SETUP utility to disable extension of the
expanded ROM on the PCI board. Securely install the PCI
boards and PCI riser card.
Contact your service representative to replace the PCI
board, system board, or PCI riser card.
5-16 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1. POST Error Codes and Messages (continued)
On-screen error message
Action
8110 Processor 1 Internal error
(IERR)
Securely install the processor.
Contact your service representative to replace the
processor or system board.
8111 Processor 2 Internal error
(IERR)
8120 Processor 1 Thermal Trip error
8121 Processor 2 Thermal Trip error
8130 Processor 1 disabled
Securely install the processor.
8131 Processor 2 disabled
Contact your service representative to replace the
processor or system board.
8140 Processor 1 failed FRB level 3
timer
8141 Processor 2 failed FRB level 3
timer
8150 Processor 1 failed initialization Securely install the processor.
on last boot
If the message is displayed each time the system is
8151 Processor 2 failed initialization booted, contact your service representative to replace the
on last boot processor or system board.
8160 Processor 01: unable to apply Contact your service representative to replace the
BIOS update
processor or system board.
8161 Processor 02: unable to apply
BIOS update
8170 Processor P1 :L2 cache failed
8171 Processor P2 :L2 cache failed
8180 BIOS does not support current
stepping for Processor P1
8181 BIOS does not support current
stepping for Processor P2
8190 Watchdog Timer failed on last Securely install the processor.
boot
If the message is displayed each time the system is
8191 4:1 Core to bus ratio:
Processor Cache disabled
booted, contact your service representative to replace the
processor or system board.
Problem Solving 5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1. POST Error Codes and Messages (continued)
On-screen error message
Action
8192 L2 Cache size mismatch
Install processors under the same specification.
8193 CPUID, Processor Stepping
are different
8194 CPUID, Processor Family are
different
8195 Front Side Bus Speed
mismatch. System Halted
Securely install the processor.
Contact your service representative to replace the
processor or system board.
8196 Processor Model are different
8197 CPU Speed mismatch
Install processors under the same specification.
8198 Failed to load processor
microcode
Securely install the processor.
Contact your service representative to replace the
processor or system board.
8300 Baseboard Management
Controller failed to Function
Contact your service representative to replace the system
board.
8301 Front Panel Controller failed to
Function
8305 Hotswap Controller failed to
Function
8420 Intelligent System Monitoring
Chassis Opened
Install the top cover correctly.
84F1 Intelligent System Monitoring
Forced Shutdown
Confirm that the system starts normally. If the system is in
abnormal state, contact your service representative to
replace the system board.
84F2 Server Management Interface Contact your service representative to replace the system
Failed
board.
84F3 Baseboard Management
Controller in Update Mode
Ask your service representative for maintenance.
84F4 Sensor Data Record Empty
5-18 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1. POST Error Codes and Messages (continued)
On-screen error message
84FF System Event Log Full
Action
Clear the event log by using the BIOS SETUP utility. If the
error is not eliminated, contact your service representative
to replace the system board. The error message is
displayed periodically if ESMPRO is not installed. The
event log must be cleared periodically.
8500 Bad or missing memory in Slot Check to see that the all DIMMs are firmly seated in the
2A
slot.
8501 Bad or missing memory in
Slot1A
Contact your service representative to replace the memory
or system board.
8504 Bad or missing memory in Slot
2B
8505 Bad or missing memory in Slot
1B
8601 All memory marked as fail
Forcing minimum back online
8306 OS Boot Watchdog Time failure Contact your service representative.
Problem Solving 5-19
Download from Www.Somanuals.com. All Manuals Search And Download.
POST Error Code Hardware References
Figure 5-3 shows the location of specific components referenced in the POST Error
Codes and Messages table.
! Fan modules
Fan 5 (Option)
Fan 1
Fan 3 (Option)
! Processor/Memory
Slot 1A (DIMM 1A)
Processor 1
Slot 1B (DIMM 1B)
Slot 2A (DIMM 2A)
Slot 2B (DIMM 2B)
Processor 2
NOTE: Failed CPU or memory boards can be also identified with the SETUP
utility.
Note: DIMMs are always added in pairs in the ascending
order of DIMM socket numbers.
1A
1B
2A
DIMM #1-A
DIMM #1-B
DIMM #2-A
DIMM Group Bank #1
DIMM Group Bank #2
2B
DIMM #2-B
Figure 5-3 . Processor and DIMM Locations on the System Board
5-20 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Beep Codes
If an error occurs during the POST, the server beeps, indicating the type of error.
Each number indicates the number of short beeps, and a hyphen indicates a pause. For
example, the beep interval 1-5-2-2 indicates 1 beep, pause, 2 beeps, pause, 2 beeps,
pause, and 3 beeps notifying that no processor is detected on the system board.
Table 5-2. Post Error Beep Codes
Beeps
Error
Recommended Action
1
Refresh timer error
Contact your service representative to replace the system board
2
3
Parity error
Check if the DIMM cards are mounted correctly. If the error still
occurs when the check result is normal, contact your service
representative to replace the DIMM card or system board.
Base memory failure
4
5
6
System timer error
Processor failure
Contact your service representative to replace the system
board.
Contact your service representative to replace the processor or
system board.
Keyboard controller
error
Check if the keyboard is connected correctly.
Contact your service representative to replace the keyboard or
system board.
7
8
Processor exception Contact your service representative to replace the processor or
interrupt error
system board.
Display memory
read/write error
Contact your service representative to replace the system
board.
9
ROM checksum error Contact your service representative to replace the system
board.
10
Shutdown register
error
11
BIOS disabled
1-5-1-1 FRB failure
Contact your service representative to replace the processor or
system board.
1-5-2-1 Processor type error Check if the type of the mounted processor is correct. If the
error still occurs when the check result is normal, contact your
service representative to replace the processor or system
board.
1-5-2-2 Processor not
detected
Check if the processor is mounted correctly. If the error still
occurs when the check result is normal, contact your service
representative to replace the processor or system board.
1-5-4-2 Power failure
Contact your service representative to replace the power supply
unit, power jumper board, or system board.
1-5-4-3 Chip set control error Contact your service representative to replace the system
board.
1-5-4-4 Power control error
Contact your service representative to replace the power supply
unit, power jumper board, or system board.
Problem Solving 5-21
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Identify BIOS and BMC Revision Levels
To identify your system's current BIOS and BMC revision levels, perform the following
procedure:
1. Power-on or reboot the system. “Press <F2> to enter SETUP” displays.
2. Press F2. The BIOS Setup Utility starts and the Main Menu is displayed. The menu
bar at the top of the Main Menu lists the following selections:
Menu
Use
Main
Use this menu for basic system configuration.
Advanced
Use this menu for setting the Advanced Features available on
your system.
Security
Use this menu to set User and Supervisor Passwords and the
Backup and Virus-Check reminders.
Server
Boot
Exit
Use this menu for configuring unique Server features.
Use this menu to configure Boot Device priority.
Exits the current menu.
3. Use the arrow keys to select the Server menu.
4. Select System Management and press ENTER. The BIOS and BMC revision level
are displayed.
5-22 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamps
The following describes lamps on the server and their indications. See Chapter 2 for
each location.
1
LAN ACCESS Lamp ( )
The LAN ACCESS lamp is lit green when the server is connected to LAN. The lamp
blinks while the server is accessed through the LAN (for packet transmission). The
value next to the icon indicates the number of the network port on the rear panel.
STATUS Lamp ( )
The STATUS lamp stays lit in green when the server is in successful operation. When
the STATUS lamp is unlit or lit/flashing in amber, it indicates that the server has failed.
The following table lists indications of the STATUS lamp, descriptions, and actions to
take.
NOTES:
! If the server has the ESMPRO or Off-line Maintenance Utility installed, you can
view the error log to identify the cause of a trouble.
! To cycle power to the server, shut down the server from the OS to and reboot
it, if available. If the shutdown from the OS is not available, disconnect and
connect the power cord to reboot the server.
Problem Solving 5-23
Download from Www.Somanuals.com. All Manuals Search And Download.
STATUS lamp
indication
Description
Procedure
On (green)
Flashing
(green)
The server is operating normally.
–
• The server is operating with the
memory, CPU, or power supply
unit in degraded state.
Check the AC POWER lamp
indication on the rear panel of the
server.
• A single-bit memory error has
often occurred.
Identify the device in degraded state
by using the BIOS setup utility
"SETUP," and replace it as soon as
possible.
Off
The power is off.
–
POST is in progress.
Wait for a while. The STATUS lamp
turns green when POST is completed.
A CPU error occurred.
A CPU temperature alarm was
detected. (Thermal-Trip)
A timeout occurred when the time
set for the watchdog timer arrived.
Turn the power off and then turn it on.
If the POST screen displays an error
message, take notes of the message,
and contact your sales representative.
A CPU bus error occurred.
A memory dump request is made.
Wait until the memory dump is
completed.
On (amber)
A temperature alarm was detected.
Check if the internal fans are clean
and if the fan units are firmly
connected.
If the STATUS lamp indication does
not change when the fans are normal,
contact your sales representative.
A voltage alarm was detected.
All the power supply units failed.
Contact your sales representative.
Flashing
(amber)
Either of the following was detected
in the redundant power
configuration:
• AC power not supplied to one of
the two power supply units
• Failure of one of the two power
supply units
Connect the power cord to supply
power. If the power supply unit is
faulty, contact your sales
representative.
A fan alarm was detected.
Check if the fan units are firmly
connected.
If the STATUS lamp indication does
not change when the fans are normal,
contact your sales representative.
A temperature warning was
detected.
Check if the internal fans are clean
and if the fan units are firmly
connected.
If the STATUS lamp indication does
not change when the fans are normal,
contact your sales representative.
5-24 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER/SLEEP Lamp ( )
The green POWER/SLEEP lamp lights to indicate normal operation while the server is
powered. When the server is off-powered, the POWER/SLEEP lamp stays unlit.
The POWER/SLEEP lamp indicates that the server is running in the power-saving
mode (sleep mode). If the OS supports the power-saving mode such as Windows 2000,
pressing the SLEEP switch blinks the POWER/SLEEP lamp in green and places the
server in the power-saving mode. Press the POWER switch to turn out the
POWER/SLEEP lamp and place the server back in the normal mode.
The power-saving mode is only available when the OS supports the power-saving
feature. Some OS's allow you to set the server to automatically turn in the power-
saving mode when no access is made to the server for a certain period of time or to
select the power-saving mode with a command.
DISK ACCESS Lamp ( )
The DISK ACCESS lamp indicates the state of hard disks in the 3.5-inch hard disk
drive bay.
This lamp lights in green every time any of such hard disks is accessed.
When the DISK ACCESS lamp is lit in amber, it indicates that a hard disk error
occurred. To identify a failed hard disk, see the lamps provided for each hard disk.
When the DISK ACCESS lamp lashes in green and amber by turns or in amber only, it
indicates that hard disks connected to the internal disk array controller are in auto-
rebuilding (reconfiguration).
Access Lamps
The access lamps for the floppy disk drive and the CD-ROM drive light when access is
made to a media in the drive.
Problem Solving 5-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Hard Disk Drive Lamp
The disk lamp on the 3.5-inch hard disk drive bay has different meanings depending on
the display status. See Figure 5-4.
Lamp
Figure 5-4. Hard Disk Drive Lamp Location
! Lighting green
Indicates that the power is supplied to the hard disk.
! Blinking green
Indicates that the hard disk is accessed.
! Lighting amber
Indicates that the installed hard disk is defected in the disk array configuration.
NOTE: While hard disks are in the disk array configuration (RAID1 or RAID5), a single
failed hard disk does not affect the operation of the server. However, it is recommended to
replace the failed hard disk and auto-rebuild (reconfigure) the hard disks as soon as
possible. (You can hot-swap such a failed hard disk.)
! Alternate lighting green or amber
Indicates that the hard disk is being rebuilt (this status is not a failure). If the defected
hard disk is replaced with a new one in the disk array configuration, the data is
automatically rebuilt (auto rebuild function). During the rebuild operation, the lamp is
lit green or amber alternatively.
The lamp goes off when the rebuild is terminated normally. The lamp goes on amber if
the rebuild fails.
IMPORTANT: To abort rebuilding, power off the server. In such a case, restart the
server, hot-swap the failed hard disk, and restart rebuilding. Observe the following notes
to use the auto-rebuild feature.
!
!
!
Do not power off the server. (If the server is powered off before rebuilding hard disks,
the auto-rebuild feature will not start.)
When you removed a hard disk, wait at least 90 seconds before installing the hard disk
back again.
Do not replace another hard disk while rebuilding is in progress.
5-26 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Supply Lamps
The power supply on the rear of the server has three lamps. See Figure 5-5.
DC power lamp
Power status lamp
AC power lamp
Figure 5-5. Power Supply Lamp Locations
NOTE: The server equipped with an optional power unit can continue the operation with
the normal power unit if the other power unit is defected (redundant function). The
defected power unit can be replaced with a new one in the hot-swap mode without power
interruption.
DC Power Lamp
If the power cord is connected to the AC inlet to supply AC power to the power unit,
the lamp blinks green. When the power of the server is turned on, the lamp goes on
green. If the lamp is not lit after turning on the power of the server, the power unit may
be defected. Contact you service representative to replace the power unit.
Power Status Lamp
If a power supply failure (such as a fan performance problem, current limit, and
overload voltage) is detected, this lamp goes on amber. Contact you service
representative to replace the power unit.
AC Power Lamp
If the power cord is connected to the AC inlet to supply AC power to the power unit,
the lamp goes on green. If the lamp is not lit after supplying AC power, the power
supply bay may be defected. Contact you service representative to replace the power
supply bay.
Problem Solving 5-27
Download from Www.Somanuals.com. All Manuals Search And Download.
LAN Connector Lamps
Each of the two LAN connectors on the rear panel has two lamps as follows.
LINK/ACT lamp
LAN2
1000/100/10 lamp
LINK/ACT lamp
LAN1
100/10 lamp
! LINK/ACT lamp
The link/ACT lamp indicates the state of each network port normally equipped with the
server. If the power is supplied to the server and the hub and they are correctly
connected with each other, the lamp is lit green (LINK state). If information is
transmitted through a network port, the lamp blinks green (ACT state).
If the lamp is not lit in the LINK state, check the network cable and the cable
connection. If the lamp is not lit still after the checking, the network (LAN) controller
may be defected. Contact your service representative.
! 100/10 lamp (LAN1)
The 100/10 lamp indicates whether each of the network ports normally equipped with
the server is operated through the 100BASE-TX or 10BASE-T network interface. If the
lamp is lit amber, the network port is operated through 1000BASE-T. If the lamp is off,
the network port is operated through 10BASE-T.
! 1000/100/10 lamp (LAN2)
The 1000/100/10 lamp indicates whether each of the network ports normally equipped
with the server is operated through the 1000BASE-T, 100BASE-TX or 10BASE-T
network interface. If the lamp is lit amber, the network port is operated through
1000BASE-T. If the lamp is lit green, the network port is operated through 100BASE-
TX. If the lamp is off, the network port is operated through 10BASE-T.
5-28 Problem Solving
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Illustrated Parts Breakdown
! Exploded View
! Field Replaceable Units
Download from Www.Somanuals.com. All Manuals Search And Download.
This chapter provides an exploded view and parts lists for the major assemblies of your
server.
Exploded View
1
2
3
29
4
8
5
6
7
28
9
10
11
12
27
13
14
26
4
15
26
16
23
21
20
19
25
24
18
17
22
6-2 Illustrated Parts Breakdown
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
Reference
Number
Description
Part Number
1
5.25-inch Peripheral Devices. Refer to subsection “Tape Drives” in
this chapter.
2
3
4
5
6
CDROM Drive Mitsumi FX-4840W
Sub Bezel (Front Panel)
856-850222-001A
6896470000
3.5-Inch FDD, Mist White D353M3D
Hard Disk Drive Carrier
6786020200
245-01509-000
Hard Disk Drives: Refer to subsection “Hard Disk Drives” in this
chapter.
7
8
Tower Feet
HDD Cage, Hot Swap
Power Supply Backboard
Power Supply
9
6896460000
10
Hot-Swap DPS-450FB D
Non Hot-Swap 450W PS/2
IO Shield
313-01532-000
856-060342-505A
11
12
13
Rear Fan
Memory DIMMs: Refer to subsection “Memory Expansion” in this
chapter.
14
15
Retention Module
6867350000
System Board (Processors, Memory, Retention Module not
included)
856-122387-001
16
Raid Controllers and Cache: Refer to subsections “RAID
Controllers and Cache” and “SCSI Controllers” in this chapter.
17
18
19
20
Side Panel
PS/2 Mouse, Mist White
Heat sink Clip P533
6887430000
Processor(s): Refer to subsection “Pentium Processors” in this
chapter.
21
CPU Heat Sink
309-01530-000
Illustrated Parts Breakdown 6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Number
Description
Part Number
22
23
24
25
26
27
28
Master Key
SCSI Backplane
DLT Bracket Kit
104-Key Keyboard
856-122575-001
Intrusion Switch Assembly (included in 6896590000)
LED/Switch Assembly (included in 6896590000)
Redundant Fan Assembly
6901600000
856-060342-502A
6884800000
29
Front Bezel (Door)
6896480000
6-4 Illustrated Parts Breakdown
Download from Www.Somanuals.com. All Manuals Search And Download.
Pentium Processors
Replaceable Parts
Description
Part Number
Intel™ Xeon™ 2.0GHz/533/512 Processor
6884920000
Intel™ Xeon™ 2.4GHz/533/512 Processor
Intel™ Xeon™ 2.66GHz/533/512 Processor
Intel™ Xeon™ 2.8GHz/533/512 Processor
6884940000
6889470000
6884930000
Hard Disk Drives
Replaceable Parts
Description
Part Number
Kit, 18 GB ATLAS320-18SCA FWB411
6893360000
Kit, 36 GB ATLAS320-36SCA FWB411
6893370000
6893380000
6893390000
6893400000
6893410000
Kit, 73 GB ATLAS320-73SCA FWB411
Kit, 18 GB SCSI, 15K RPM, ST318453LC FW0002
Kit, 36 GB SCSI, 15K RPM, ST336753LC FW0002
Kit, 73 GB SCSI, 15K RPM, ST373453LC FW0002
DVD Drives
Replaceable Parts
Description
Part Number
DVDR SR8588 BNN MATSUSH FW7Z16
6892800000
DAT Tape Drives
Replaceable Parts
Description
Part Number
20/40 GB DDS4 DAT ELEPHANT EARS FW 02N9
6872100200
DLT VS80 TANDBERG TAPE DRIVE
6889490000
6856880300
6856890300
6890050100
6873450200
AIT-1 DRIVE SDX 400C DUST FW 07N6
AIT-2 DRIVE SDX 500C DUST FW 01NM
AIT-3 DRIVE SDX 700C DUST FW 01NM
AIT- 2 AUTO-LOADER TSL A500C FWL1NB
Illustrated Parts Breakdown 6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Controllers and Cache
Replaceable Parts
Description
Part Number
RAID LSI 518, 2-CH 320-2 1L19
6893990000
RAID LSI 520, 1-CH 320-1 1L19
Cache, 128 MB, M374S1723DTS-C7A
Battery Backup, FOR LSI RAID Card 320-2
RAID LED Cable
6894000000
6865270000
6891630000
320-01688-000
6891640000
Battery Backup, FOR LSI RAID Card 320-1
SCSI Controllers
Replaceable Parts
Description
Part Number
ADAPTEC AHA29160 64-BIT NE LAT
6829240100
ADAPTEC AHA2944UW For Servers
1301630000
Network Controllers
Replaceable Parts
Description
Part Number
INTEL 1000BASE-SX ADAPTER BOARD
154-01504-000
LAN PRO1000XT PWLA8490XT INTEL
LP952L-F2 B1.60A7 FW3.90A7
6893180000
6895780000
Memory Expansion
Replaceable Parts
Description
Part Number
DIMM, 128 MB M383L1713DTS-CBO
6863170000
DIMM, 256 MB M383L3223DTS-CBO
DIMM, 512 MB M383L6420DTS-CBO
DIMM, 1GB M383L2828DTS-CBO
6874140000
6874130000
6874120000
6-6 Illustrated Parts Breakdown
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable List
Description
Part Number
120Lg Cable Kit (not a FRU, Only for order)
6896590000
LED/SW Cable (included in 6896590000)
HDD Activity Cable (included in 6896590000)
Port COM Cable (included in 6896590000)
IDE CDROM Cable (included in 6896590000)
FDD Cable (included in 6896590000)
6896490000
6896510000
6896420000
6896430000
6896450000
6895050000
U320 SCSI Cable 2Conn 68P 0.9M (use to link
backplane to system board or an additional SCSI
controller)
RAID LED Cable
320-01688-000
320-01676-000
6865960000
U160 EXT SCSI Cable
TM1300 6 CONN SCSI Cable with terminator (Use
for additional tape drive)
Illustrated Parts Breakdown 6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Specifications
! System Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
System Specifications
Item
NEC Express5800/120Lg
CPU
Type
Intel Xeon processor
(1.8GHz/512KB)
Intel Xeon processor
(2.66GHz/512KB)
Number of
processors
1
Maximum
2
Chipset
E7501
Memory Standard
Maximum
256 MB (128 MB× 2)
4GB (The standard DIMM must be replaced.)
512 MB (256 MB× 2)
Expansion unit
2 DIMMs (256/512/1024MB)
Expansion times
Memory module
Error check
2 times (The standard DIMM must be replaced.)
SDRAM DIMM (DDR266, Registered)
ECC
Graphics (VRAM)
ATI RAGE XL (VRAM 8MB)
Auxiliary Floppy disk
3.5-inch drive × 1 (standard)
input
(standard)
device
Hard disk (standard) None (Hot-swap)
Hard disk
(maximum)
876 GB (146 GB × 6)
CD-ROM (standard)
ATAPI interface × 1 (x48 speed)
4 slots (Standard ATAPI CD-ROM drive is installed.) *
6 slots (Hot-swap)
5.25-inch file bay
3.5-inch device bay
Additional PCI (64-
4 slots
slot
bit/100MHz)
PCI (32-bit/33MHz) 2 slots
LAN interface
1000BASE-T/100BASE-TX/10BASE-T (1 port),
100BASE-TX/10BASE-T (1 port)
External Keyboard
MINI DIN 6-pin connector (1 port)
MINI DIN 6-pin connector (1 port)
4-pin (3 ports)
interface
Mouse
USB
Serial
D-sub 9-pin (2 ports)
Parallel
Network
Display
SCSI
D-sub 25-pin (1 port)
RJ-45 (2 ports)
MINI D-sub 15-pin (1 port)
Ultra320/160 SCSI (1 port)
(An exclusive use with internal SCSI for hard disk drive)
Cabinet design
Desk-side, mini tower
External dimensions
292.1* (width) × 453 (height) × 681 (depth) mm
* including stabilizers
Weight
35 kg (Max.)
Power supply
100 to 120 VAC ±10%, 200 to 240 VAC ±10%, 50/60 Hz ±1 Hz
(Hot-swap)
Power consumption
480 VA, 465 W
Environmental Temperature 10 to 35°C
requirements
Humidity
20 to 80% RH (no condensation)
Others
NEC EXPRESSBUILDER supported, NEC ESMPRO provided in
the standard configuration
* A maximum of three file devices can be installed in this system
(including standard ATAPI CD-ROM drive).
A-2 Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Installing and Configuring
Windows® 2000
! Overview
! Device Drivers
! Installation Assumption
! Installation Preparation
! Installing Microsoft Windows® 2000 Operating
System
! Installing LAN Adapters
! Driver Installation for the ATI RAGE XL Display
Adapter
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
This appendix contains supplemental instructions needed to install and
configure hardware and software used with the Microsoft Windows® 2000
Operating System. This information is intended to supplement the more detailed
procedural documents available from Microsoft. This information is not
intended to be the central source of installation and configuration information
for your system. Read this entire chapter along with Microsoft's Windows®
2000 Setup procedures before starting the installation process.
Note: Read the System Release Notes for the latest
system information before attempting to install Windows
2000 Operating System on your system.
Device Drivers
The drivers required for the devices listed in Table B-1 below are located on the
EXPRESSBUILDER CD that is included with your system. To create the
required diskettes, perform “Tools” on the EXPRESSBUILDER CD.
!
CAUTION
When creating the required diskettes from the
EXPRESSBUILDER CD make sure you use the drivers
required for the devices on your specific system.
Always read the information in the release notes or inserts,
included with any options for they supersede the information
in this guide.
Table B-1. Device Drivers
Supported Device
Required Driver Media*
SCSI Controllers
HALs
Windows 2000 OEM Diskette* (If applicable)
System Board
Windows 2000 Update Module**
*Diskette generated from the EXPRESSBUILDER CDROM
**Run this application from the EXPRESSBUILDER CDROM; diskette not required
B-2 Installing and Configuring Windows 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Assumption
The installation and configuration instructions in this chapter assume the
following:
! You have properly completed the hardware installation.
! You have run the BIOS Setup Utility to check system configuration.
! You will be installing Windows® 2000 Operating System from the
CD-ROM media.
Note: If you have an optional disk array controller
preinstalled on your system, it was preconfigured at the
factory. Refer to your system's User's Guide and to the RAID
Installation Guide and the Disk Array Controller Installation
Guide and User’s Manual for additional information on this
option card. If you need to change the RAID level from the
factory setting, you must change the setting before installing
the operating system.
Installing and Configuring Windows 2000 B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
Before starting the installation procedure, you need to obtain certain information
for use during the installation. Table B-2 lists the information you need in
advance for the installation. It is recommended that you obtain the information
from your server administrator and record it in Table B-2 before starting.
After completing the installation, you might want to use the Windows 2000
Control Panel to configure additional devices or Windows 2000 services and
facilities.
Table B-2. Advanced Information
Item
Information Required
Enter Your Information Here
1
2
3
Name of the Windows 2000 user.
Name of the licensed organization.
Product Key number for Microsoft
Windows 2000 Server Software.
This number is on the Certificate of
Authenticity included with your
Windows 2000 Server Software.
4
5
Name that you assign to the server.
Obtain your network configuration
information. For example, if network
settings are to be customized:
TCP/IP Configuration values such
as IP address values, DNS and
WINS address resolution facilities,
DHCP Relay and Routing
configuration values.
6
The name of any Administrative
Domain or Workgroup that this
server is to be a member of.
B-4 Installing and Configuring Windows 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Microsoft Windows® 2000 Operating
System
Use the following procedure to set up and perform a clean Windows 2000
Operating System installation on your server. Before performing the installation,
read the “Installation Notes” in the following section.
Installation Notes
Before beginning the Windows 2000 installation, consult your server’s “System
Release Notes” to determine whether SCSI controller device drivers and/or
Hardware Abstraction Layer (HAL) programming on the “Windows 2000 OEM
DISK” are required.
Windows 2000 Installation
1. Insert the Windows 2000 CD into the CD-ROM drive and boot your system
by pressing CTRL+ALT+Delete. If a bootable operating system is installed,
press Enter while the message “Press any key to boot from CD” is
displayed at the top of the screen.
Note: Perform Step 2 if a SCSI Disk or RAID controller
drivers and/or HAL on the “Windows 2000 OEM DISK” are
required; otherwise go to Step 9.
2. While the message “Setup is inspecting your computer’s hardware
configuration” or a solid blue background is displayed on the screen,
perform one of the following:
! Press the F6 key if SCSI Disk or RAID Controller drivers are included on
the “Windows 2000 OEM DISK,” are required.
! Press F5, if a HAL included on the “Windows 2000 OEM DISK,” is
required.
! Press F5 and F6 simultaneously if both a SCSI Disk or RAID Controller
drivers and HAL programming are included on the “Windows 2000 OEM
DISK.”
Note: There is no visible indication on the screen when
the F5 or F6 key is pressed.
Note: Perform Steps 3 and 4 if you pressed F5; perform
Steps 5 through 8 if you pressed F6.
Installing and Configuring Windows 2000 B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. When the following message is displayed, select Other, then press Enter.
“Setup could not determine the type of computer you have, or you have
chosen to manually specify the computer type.
Select the computer type from the following list or select “Other” if you
have the device support disk provided by the computer manufacturer.”
4. Insert the “Windows 2000 OEM-Disk” into the floppy diskette drive, and
press Enter. Select the computer type which is displayed.
5. When the following message is displayed, press S.
“Setup could not determine the type of one or more mass storage devices installed in
your system, or you have chosen to manually specify an adapter”. Currently, Setup will
load support for the following mass storage devices.
6. When the following message is displayed, select Other then press Enter.
Select the SCSI Adapter your want from the following list, or select "Other" if you have
a device support disk provided by an adapter manufacturer
7. Insert the "Windows 2000 OEM-DISK" diskette into the floppy disk drive,
and press Enter. A list of mass storage devices is displayed.
8. Select the RAID disk array controller installed in your server from the list of
mass storage devices.
9. Follow the messages on the screen to continue to install.
Note: Please consult the Microsoft Windows 2000
Installation Guide for more extensive installation procedures.
For LAN adapter driver installation, see Installing LAN
Adapter Drivers later in this chapter.
10.After installing Windows 2000, logon to the system using the administrator
account or other account, which is a member of the Administrator’s group.
11.Insert the EXPRESSBUILDER CD into the system CDROM drive. The
“Master Control” menu displays. Select Setup and then select Update NEC
5800 System from the displayed menu items.
Note: If you change the configuration of the system (by
adding or removing hardware or operating system software
components), or repair the system, you must run the
Windows 2000 Update Module again.
B-6 Installing and Configuring Windows 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing LAN Adapters
The following section includes special driver installation instructions for the
Intel PRO/100+ LAN adapter used in your system.
Driver Installation for the Intel PRO/100+ LAN Adapter
The PRO/100+ driver is initially installed during the installation of Windows
2000 and upgraded when you run the “Windows 2000 Update Module, see
“Installing Microsoft Windows® 2000 Operating System” found earlier in this
appendix. In order to utilize the PRO/100+ LAN adapter “teaming features,” use
the following procedure to install “PROSET II for Windows 2000.”
1. Power on, start Windows 2000, and log on.
2. Insert the EXPRESSBUILDER CD into the system CDROM drive. The
“Start” menu displays. Cancel out of the Start menu and run:
D:\WINNT\W2k\PC62\HD1\WINDOWS\PROSet2\IA32\PROSet.msi
(where D: is the drive letter for your CDROM drive.) Note: PROSet.msi
may not be located in the exact location described here.
The Intel PROSetII install wizard displays.
3. Click on the NEXT button and select “I accept the terms in the license
agreement.”
4. Click on the NEXT button and the installation options screen displays.
Select “TYPICAL” and click on the NEXT button.
5. Click on the INSTALL button. The message "Digital signature not found"
displays.
6. Click on the YES button. “Install Shield Wizard Completed” appears after
all files have been copied.
7. Click on FINISH button. Once the ProSetII driver installation completes,
reboot the system.
8. Proceed to the next section to set transfer speed and duplex mode.
Setting Network Driver Details.
1. Open the Control Panel and double-click the “Intel(R) PROSetII” icon. The
82546EB Based Dual Port Network Connection screen displays.
2. Select “Intel(R) 82546EB Based Dual Port Network Connection #1.”
3. Select the “Link Configuration” tab and set the “Auto Negotiation” value to
DISABLE. Also set the “Forced Speed and Duplex” value according to the
value specified for your HUB.
4. Select “Intel(R) 82546EB Based Dual Port Network Connection #2.”
Installing and Configuring Windows 2000 B-7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select the “Link Configuration” tab and set the “Auto Negotiation” value to
DISABLE. Also set the “Forced Speed and Duplex” value according to the
value specified for your HUB.
Note: When selecting the "1000/Full" setting, set
“Auto Negotiation” to ENABLE and select only the
"1000/Full" setting at the “Negotiable Speeds and
Duplexes” item. Also, add/delete any other protocols and
services, as necessary.
Driver Installation for the ATI RAGE XL
Display Adapter
To take full advantage of the on-board ATI RAGE XL display adapter, perform
the following driver installation procedure:
1. Power on, start Windows 2000, and log on.
2. Insert the EXPRESSBUILDER CD into the system CDROM drive. The
“Start” Menu displays. Cancel out of the Start menu and run:
D:\WINNT\Video\W2k\Setup.exe
(where D: is the drive letter for your CDROM drive.)
3. Follow the screen prompts.
4. When the message "Digital signature not found" displays, select YES to
continue the installation.
5. At the conclusion of the ATI Rage XL installation, reboot the system.
B-8 Installing and Configuring Windows 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
C
IRQ and I/O Port Addresses
! Interrupt Requests
! PIRQ and PCI Device
Download from Www.Somanuals.com. All Manuals Search And Download.
Interrupt Requests
The factory-set interrupt requests (IRQs) are listed below.
IRQ
0
Peripheral Device (Controller)
IRQ
12
13
14
15
16
17
18
19
30
31
49
50
Peripheral Device (Controller)
System timer
Mouse
1
Keyboard
Numeric processor
Primary IDE
Secondary IDE
USB
2
–
3
COM2 serial port (PCI)
4
COM1 serial port (PCI)
5
PCI
VGA
6
Floppy disk drive
–
7
PCI
USB
8
Real-time clock
LAN1
9
ACPI compliant system
LAN2
10
11
PCI
PCI
Adaptec SCSI
Adaptec SCSI
PIRQ and PCI Device
The factory-set PCI device interrupts are assigned as follows. Use the BIOS setup
utility, BIOS, for interrupt setup.
Menu Option
Interrupt
PCI IRQ 1
On-board SCSI (Channel 0), PCI slot #6 (INT D)
PCI IRQ 2
PCI IRQ 3
PCI IRQ 4
PCI IRQ 5
PCI IRQ 6
PCI IRQ 7
PCI IRQ 8
PCI IRQ 9
PCI IRQ 10
PCI IRQ 11
PCI IRQ 12
On-board SCSI (Channel 1), PCI slot #6 (INT C)
On-board LAN #1
On-board LAN #2
On-board GA
PCI slot #3 (INT A)
PCI slot #4 (INT A)
PCI slot #6 (INT A)
PCI slot #2 (INT A)
PCI slot #5 (INT A)
PCI slot #1 (INT A)
PCI slot #1 (INT D), PCI slot #2 (INT B), PCI slot #3 (INT B),
PCI slot #4 (INT C), PCI slot #5 (INT C)
PCI IRQ 13
PCI IRQ 14
PCI slot #1 (INT B), PCI slot #2 (INT C), PCI slot #3 (INT C),
PCI slot #4 (INT D), PCI slot #5 (INT D), PCI slot #6 (INT B)
PCI slot #1 (INT C), PCI slot #2 (INT D), PCI slot #3 (INT D),
PCI slot #4 (INT B), PCI slot #5 (INT B)
C-2 IRQ and I/O Port Addresses
Download from Www.Somanuals.com. All Manuals Search And Download.
I/O Port Address
The factory-set I/O port addresses for the server are assigned as follows:
Address
Chip in Use
00 - 1F
20 - 21
2E - 2F
40 - 43
60
8-bit DMA control register
Master 8259 programming interface
Configuration
8254 programming interface
Keyboard & mouse
61
NMI status register
64
Keyboard & mouse
70 - 71
80 - 8F
A0 - A1
C0 - DF
E0 - E9
F0
NMI enable register/real-time clock
16-bit DMA control register
Slave 8259 programming interface
DMA controller page register
Base address register
Register IRQ13
F1 - FF
Logical device configuration
EDMA2-compatible mode primary command block register
EDMA2-compatible mode secondary command block register
(Parallel port 3)
170 - 177 or BAR2
1F0 - 1F7 or BAR0
278 - 27F
2F8 - 2FF
BAR or 376
370 - 377
378 -37F
3B0 - 3BB
3BC - 3BE
3C0 - 3DF
3F6 or BAR1
3F0 - 3F7
3F8 - 3FF
40B
Serial port 2
EDMA2-compatible mode secondary command block register
(Floppy disk drive 2), IDE 2
(Parallel port 2)
VGA
Parallel port 1
VGA
EDMA2-compatible mode primary command block register
Floppy disk drive 1, IDE 1
Serial port 1
DMA1 expansion write mode register
Master 8259 ELCR programming
Slave 8259 ELCR programming
DMA2 expansion write mode register
SMBus control
4D0
4D1
4D6
580 - 58F
IRQ and I/O Port Addresses C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Address
Chip in Use
PCI IRQ mapping index register
C00
C01
C14
C49
C4A
C52
C6C
C6F
PCI IRQ mapping data register
PCI error status register
Address & status control
Rise time counter control
General register (GPMs)
ISA wait register
Other control registers
IPMI (MPI KCS interface)
IPMI (SMI interface)
CA2 - CA3
CA4 - CA5
CA6 - CA7
CD6
IPMI (SCI/SW1 interface)
Power management index register
Power management data register
PCI configuration space
Reset control
CD7
CF8, CFC
CF9
F50 - F58
General chipset
FE00 - FE3F
BAR4+00 - 0F
Chipset
EDMA2 PCI base address register 4
*1 Hexadecimal notation
*2 The I/O port address of a PCI device is set according to its type and number.
C-4 IRQ and I/O Port Addresses
Download from Www.Somanuals.com. All Manuals Search And Download.
D
Internal Cabling Diagrams
! Standard Configuration
! Disk Array Configuration of Built-in Hard Disks
! Installing a SCSI File Device
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Configuration
The figure below shows an example of the connections in the standard configuration.
Option
5.25-inch
device bay
System board
CD-ROM
Option
Floppy disk
drive
Floppy disk
PCI #1
PCI #2
PCI #3
PCI #4
IDE
IDE
ID5
ID4
ID3
ID2
ID1
ID0
PCI #5
PCI #6
3.5-inch
hard disk
drive bay
SCSI
Hard disks
are optional.
SCSI cable
IDE cable
Floppy disk drive cable
D-2 Internal Cabling Diagrams
Download from Www.Somanuals.com. All Manuals Search And Download.
Disk Array Configuration of Built-in
Hard Disks
For the disk array configuration of hard disks installed in the built-in 3.5-inch device
bays, the disk array controller board of an option is installed in the server and the SCSI
cable connected to the Ultra320 connector is disconnected from the connector and then
connected to the disk array controller board instead. The server can be equipped with
up to four disk array controller boards.
Some disk array controllers contain more than one channel. For such a disk array
controller, you may connect one of the two channels to the built-in SCSI backboard
joined with the hard disk in a 3.5-in device bay and the remaining channel to a
additional disk unit. A disk array controller of another type has two connectors in a
channel, or external and built-in connectors. Note that a single channel may not be used
for both external and built-in devices.
Option
5.25-inch
System board
device bay
CD-ROM
Option
With a disk array
controller having more
than one channel, you
may connect the other
channel with additional
disk unit.
Floppy disk
drive
Disk array controller board
Floppy disk
PCI #1
PCI #2
PCI #3
PCI #4
ID5
IDE
IDE
PCI #5
PCI #6
ID4
ID3
ID2
ID1
ID0
Disk array
SCSI
DAC
LED
IDE cable
SCSI cable
Floppy disk drive cable
DAC LED cable
Internal Cabling Diagrams D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing a SCSI File Device
With the standard configuration, you need an optional SCSI controller and internal
SCSI cable to install a file device.
Terminator
SCSI ID1
5.25-inch
System board
device bay
CD-ROM
SCSI cable (optional)
SCSI ID0
Floppy disk
drive
SCSI controller board
Floppy disk
PCI #1
PCI #2
PCI #3
PCI #4
IDE
IDE
ID5
ID4
ID3
ID2
ID1
ID0
PCI #5
PCI #6
SCSI
SCSI cable
IDE cable
Floppy disk drive cable
Set SCSI IDs as shown in the above figure. Set the terminating resistor
(Enabled/Disabled) for the last-connected device in the SCSI chain. Set "Disabled" for
all the middle devices. A terminating connector may be installed depending on the
internal SCSI cable. If the SCSI cable ends with a terminating resistor, set "Disabled"
for all the terminating resistors of connected devices. For the settings, see the manual
provided with each device.
A file device needs settings such as a SCSI transfer rate. For the transfer rate, see the
manual provided with the file device. Use the BIOS utility of the SCSI controller to
make the settings. For details, see the manual provided with the SCSI controller.
An onboard Ultra320 SCSI connector can be used to connect with internal SCSI file
device.
D-4 Internal Cabling Diagrams
Download from Www.Somanuals.com. All Manuals Search And Download.
The following figure shows an example of onboard SCSI connection for SCSI file
devices.
Terminator
SCSI ID1
System board
5.25-inch
device bay
CD-ROM
SCSI cable (optional)
SCSI ID0
Floppy disk
drive
Disk array controller board
Floppy disk
PCI #1
PCI #2
PCI #3
PCI #4
IDE
IDE
PCI #5
PCI #6
ID5
ID4
ID3
ID2
ID1
ID0
Disk array
SCSI
DAC
SCSI cable
IDE cable
DAC LED cable
Floppy disk drive cable
In the figure above, the standard hard disk drive bay is connected with an optional
RAID controller.
Internal Cabling Diagrams D-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
A
AC
(Alternating Current) The type of current available in wall outlets. All computers must
convert alternating current to direct current to operate. See also DC.
ACPI
(Advanced Configuration and Power Interface) Provides the programming standard for
power management features.
address
A label, name, or number that identifies a location in computer memory.
AGP
Accelerated Graphics Port.
ASCII
(American Standard Code for Information Interchange) A standard number assigned to each
of the alphanumeric characters and keyboard control code keys to enable the transfer of
information between different types of computers and peripherals.
B
backplane slot
A connector on the backplane board in desktop computers and expansion boxes that allows
you to install circuit cards.
backup
A copy of data for safe-keeping. The data is copied from computer memory or disk to a
floppy disk, magnetic tape, or other media.
backup battery
The battery in your computer that maintains the real-time clock and the configuration
information when the computer's power is removed.
base memory
An area of memory between 0 and 640 kilobytes.
baud rate
The speed with which data is transmitted during serial communication. The computer's
operating system and software program must be configured for the same baud rate as the
communication device, such as a serial printer. See also bps.
BIOS
(Basic Input/Output System) A program stored in flash EPROM or ROM that controls the
keyboard, disk drives, video monitor, and other devices. See also flash EPROM, EPROM,
and ROM.
Glossary 1
Download from Www.Somanuals.com. All Manuals Search And Download.
bit
Derived from BInary digiT, a bit is the smallest unit of information a computer handles. See
also byte.
BMC
(Baseboard Management Controller) Contains all of the server management functions. One
major function of the BMC is to monitor system management events and log their
occurrence in the System Event Log (SEL).
boot
The process of loading the operating system into memory.
bps
(bits per second) The number of bits transferred in one second during serial communication,
such as modem transmission.
byte
A group of eight bits.
C
cache memory
A very fast, limited portion of RAM set aside for temporary storage of data for direct access
by the microprocessor.
CD-ROM drive
(Compact Disk ROM drive) A type of mass storage device that reads information from a
compact disk.
Centronics port
An industry standard parallel port. See also parallel port.
CGA
(Color Graphics Adapter) A type of video display system that provides low-resolution text
and graphics on TTL monochrome and color monitors.
CMOS
(Complimentary Metal-Oxide Semiconductor) A type of low-power integrated circuit used
in computers. See also TTL.
COM1 or COM2
The name you can assign a serial port to set or change its address. See also serial port.
command
An instruction that directs the computer to perform a particular operation.
configuration
The way in which a computer is set up to operate. Some configurable options include CPU
speed, serial port designation, and memory allocation.
2 Glossary
Download from Www.Somanuals.com. All Manuals Search And Download.
CPU
(Central Processing Unit) See microprocessor.
CRT
(Cathode-Ray Tube) The type of video display used in monitors for desktop computers.
D
DC
(Direct Current) The type of current available in the rechargeable battery packs used in
portable computers. See also AC.
default
The factory setting your computer uses unless you instruct it otherwise. For example, when
powering up, the computer will boot from the default drive.
density
The capacity of information (bytes) that can be packed onto a storage device, such as a
floppy disk.
device driver
A software program that a computer must use to recognize and operate certain hardware,
such as a mouse or a video monitor.
disk drive
A device that stores data on a hard or floppy disk. A floppy disk drive requires a floppy disk
to be inserted; a hard disk drive has a permanently encased hard disk.
DOS
(Disk Operating System) See operating system.
DRAM
(Dynamic RAM) See RAM.
E
ECC
(Error Checking and Correction) A method of detecting and correcting errors.
EEPROM
(Electrically Erasable Programmable Read-Only Memory) A type of memory device that
stores password and configuration information.
EGA
(Enhanced Graphics Adapter) A type of video display system that provides medium-
resolution text and graphics on TTL monochrome, color, and enhanced color monitors.
Glossary 3
Download from Www.Somanuals.com. All Manuals Search And Download.
EMP
The Emergency Management Port (EMP) provides an interface to the console manager.
This interface allows remote server management via a modem or direct connection.
EMS
(Expanded Memory Specification) A method of accessing memory beyond the 640K limit
of DOS by exchanging data in and out of main memory at high speeds. Some software
requires EMS to operate.
EPROM
(Erasable Programmable Read-Only Memory) A type of memory device that is usually
used to store system BIOS code. This code can be erased with ultraviolet light, but is not
lost when the computer is powered off. See also flash EPROM and ROM.
expansion slot
See backplane slot.
extended memory
The protected memory above 1M that is directly accessible by the microprocessor through
certain utilities and operating systems.
F
flash EPROM
A type of memory device that is usually used to store system BIOS code. This code can be
replaced with updated code from a floppy disk, but is not lost when the computer is
powered off. See also EPROM and ROM.
floppy disk drive
See disk drive.
format
The process used to organize a hard or floppy disk into sectors so it can accept data.
Formatting destroys all previous data on the disk.
FRB (Fault Resilient Boot
A server management feature. FRB attempts to boot the system using the alternate
processor or DIMM.
G
(Gigabyte)
1,073,741,824 bytes. See also byte.
4 Glossary
Download from Www.Somanuals.com. All Manuals Search And Download.
H
hard disk drive
See disk drive.
hardware
The physical parts of your computer, including the keyboard, monitor, disk drives, cables,
and circuit cards.
hot swap
A method used to insert or remove SCSI disk drives into or from an operating bus. This
method is typically used in RAID subsystems. When used in non-RAID subsystems the
operating system must typically be restarted.
I
IC
(Integrated Circuit) An electronic device that contains miniaturized circuitry.
IDE
(Integrated Drive Electronics) A type of hard disk drive with the control circuitry located
inside the disk drive rather than on a drive controller card.
interface.
A connection between the computer and a peripheral device that enables them to exchange
data. See also parallel port and serial port.
ISA
(Industry Standard Architecture) An industry standard for computers and circuit cards that
transfer 16 bits of data at a time.
J
jumper
A small electrical connector used for configuration on some computer hardware.
K
(Kilobyte)
1,024 bytes. See also byte.
L
LAN
(Local Area Network) A group of computers linked together within a limited area to
exchange information.
LCD
(Liquid Crystal Display) The type of video display used in portable computers.
Glossary 5
Download from Www.Somanuals.com. All Manuals Search And Download.
LED
(Light-Emitting Diode) A small electronic device that glows when current flows through it.
LPT1 or LPT2
The name you can assign a parallel port to specify its address. See also parallel port.
LVD
Super-fast Ultra 2 SCSI Low Voltage Differential (LVD) Parallel SCSI Interface. A new
SCSI interface that provides greater I/O bandwidth, device connectivity, data reliability,
and longer cable lengths for Ultra2 SCSI hard disk drives. Note that in order to achieve
LVD performance all devices including cable, controller, and drive must support LVD.
M
(Megabyte)
1,048,576 bytes. See also byte.
memory
The circuitry in your computer that stores data and programs. See also EMS, extended
memory, RAM, and ROM.
microprocessor
The integrated circuit that processes data and controls the basic functions of the computer.
modem
A device used to exchange information with other computers over telephone or data lines.
module
A circuit board that plugs into a dedicated connector on the system board in your computer.
mouse
A small input device that you guide on a flat surface to control the cursor movement and
operation of the computer when using certain software programs.
N
NVRAM
(Nonvolatile RAM) A type of RAM that retains its contents even after the computer is
powered off. This memory stores EISA configuration information. See also RAM and
SRAM.
O
operating system
A set of programs that provides the interface between other software programs and the
computer.
6 Glossary
Download from Www.Somanuals.com. All Manuals Search And Download.
P
parallel port
The connector on the back of your computer that allows the transfer of data between the
computer and a parallel device, such as a parallel printer.
partition
The process of dividing the storage space on a hard disk into separate areas so that the
operating system treats them as separate disk drives.
password
A security feature that prevents an unauthorized user from operating your computer. See
also EEPROM.
PCI
Peripheral Component Interconnect. PCI is a high-performance peripherals I/O bus
supporting data transfers of up to 528MB per second.
Pentium
A type of microprocessor, with a built-in math coprocessor, cache memory, and memory
and bus controllers, that processes and communicates 32 bits of data at a time. This
microprocessor also contains power management capabilities.
peripheral
A device connected to and controlled by the computer, such as an external disk drive or a
printer.
pixel
The smallest element that is visible on a video display. The resolution of a video display
system is measured in pixels.
PnP
(Plug-n-Play) Plug-and-play is the ability to plug a device into a computer and have the
computer recognize that the device is there. The user doesn't have to tell the computer.
POST
Power-On-Self-Test.
R
RAM
(Random-Access Memory) A temporary storage area for data and programs. This type of
memory must be periodically refreshed to maintain valid data, and is lost when the
computer is powered off. See also NVRAM and SRAM.
real-time clock
The IC in your computer that maintains the time and date.
Glossary 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ROM
(Read-Only Memory) A type of memory device that usually is used to store system BIOS
code. This code cannot be altered and is not lost when the computer is powered off. See
also BIOS, EPROM, and flash EPROM.
RS-232C port
An industry standard serial port. See also serial port.
S
SAF-TE
(SCSI Accessed Fault Tolerant Enclosure) A specification for monitoring the state of the
drives and enclosure environment (fan, power supply, temperature, etc.) using the SCSI bus
to indicate faults.
save
To store information on a floppy disk, hard disk, magnetic tape, or some other permanent
storage device.
SCSI
(Small Computer System Interface) An industry standard interface that provides high-speed
access to tape drives, hard disk drives, and other peripheral devices.
SEL
(System Event Log) A record of system management events. The information stored
includes the name of the event, the date and time the event occurred and data pertinent to
the event. Event data may include POST error codes that reflect hardware errors or software
conflicts within the system.
serial communication
Information sent sequentially, one bit at a time.
serial port
The connector on the back of your computer that allows the transfer of data between the
computer and a serial device, such as a mouse, a modem, or a serial printer.
setup program
The program that you use to change the configuration of some ISA desktop and notebook
computers. This program also contains information about the hardware in the computer.
software
Programs with specific functions, such as word processing, data base management,
communications, and operating system.
SRAM
(Static RAM) A temporary storage area for data and programs. This type of memory does
not need to be refreshed, but it is lost when the computer is powered off. See also NVRAM
and RAM.
8 Glossary
Download from Www.Somanuals.com. All Manuals Search And Download.
SVGA
(Super VGA) A type of video display system that provides very high-resolution text and
graphics on analog color monitors.
system board
The main circuit board in your computer. It contains most of the connectors and ports.
T
tape drive
A type of storage device using magnetic tape.
TTL
(Transistor-Transistor Logic) A type of integrated circuit used in computers. See also
CMOS.
U
ultra 160/m SCSI
Ultra 160/m is a parallel SCSI interface based on Ultra3 SCSI technology. This interface
features data transfer speeds up to 160MB/second (double-edge clocking), cyclical
redundancy checking (CRC) providing higher levels of data reliability, and domain
validation that detects the configuration of the SCSI bus and automatically tests and adjusts
the SCSI bus transfer rate to optimize interoperability. Note that the Ultra 160/m uses the
standard Ultra2 LVD cabling and termination, making it backward compatible for easy
implementation.
V
VGA
(Video Graphics Array) A type of video display system that provides high-resolution text
and graphics on analog color monitors.
Glossary 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Equipment Log
Use this equipment log form to record pertinent information about your system. You
will need some of this information to run the System Setup Utility. Be sure to update
the equipment log when you add options.
Record the model and serial numbers of the system components, dates of component
removal or replacement, and the name of the vendor from whom the component was
purchased. Be sure to record the same information for any components added to the
system, such as a power supply, hard disk drives, add-in boards, or printers.
Record the model and serial numbers of the unit and system board. The model and
serial numbers of the system unit are recorded on a label attached to the rear of the unit.
The location of serial numbers on add-in boards, hard disk drives, and external
equipment, such as video displays or printers, varies from one manufacturer to another.
Literature accompanying these products should illustrate or describe the location of
model and serial numbers.
Equipment Log 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial Number
(if available)
Component
Manufacturer Name & Model
Date Installed
Server
System Board
Processor 1
Processor 2
DIMM Slot 1A
DIMM Slot 1B
DIMM Slot 2A
DIMM Slot 2B
Modem
Diskette Drive
Tape Drive
CD-ROM Drive
Hard Disk Drive 1
Hard Disk Drive 2
Hard Disk Drive 3
Hard Disk Drive 4
Hard Disk Drive 5
Hard Disk Drive 6
Network Controller 1
Network Controller 2
RAID Controller
SCSI Controller
Monitor
Keyboard
Mouse
Power Supply (standard)
Power Supply (optional)
2 Equipment Log
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
H
Access lamp, 5-25
Advance menu
configuring in setup, 3-7
Hard disk, A-2
Humidity, A-2
I
B
Battery
installing, 4-11
BIOS
I/O port address, C-3
Installation assumption
Windows 2000, B-3
Installing
using the setup utility, 3-3
Windows 2000, B-5
Integrated peripheral configuration menu,
configuring in Setup, 3-8
Interface, A-2
C
CD-ROM, A-2
Configuring system board jumpers, 3-22
Configuring your system, 3-2
CPU, A-2
J
Jumpers
CMOS clear, 3-23
password, 3-23
system board, 3-22
D
Diagnostic procedures, 5-8
Dimensions, A-2
DISK ACCESS lamp, 1-4, 5-25
Drivers
K
Key hole, 1-4
Windows 2000, B-2
L
E
Lamps
access, 5-25
Error codes. See POST
Error messages, 5-15
Exit menu
DISK ACCESS, 1-4, 5-25
POWER, 1-4, 5-25
STATUS, 1-4, 5-23
LAMPS, 5-23
Lithium backup battery
installing, 4-11
configuring in setup, 3-16
External views, 1-4
F
Features, 1-12
Field replaceable units, 6-3
cable list, 6-7
M
Main menu
hard disk drives, 6-5
memory expansion, 6-6
Pentium processors, 6-5
RAID controllers and cache, 6-6
tape drives, 6-5
configuring in setup, 3-5
Memory, A-2
addresses, 1-13
N
Network
problems, 5-14
File bay, A-2
Floppy disk, A-2
FORCED SHUTDOWN, 5-4
Front door, 1-4
P
Password
clearing and changing, 3-24
PIRQ, C-2
POST
G
Graphics, A-2
error codes and messages, 5-15
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Power consumption, A-2
POWER lamp, 1-4, 5-25
Power on/off
unpacking, 2-3
System board
removing, 4-58
switch does not turn off AC power, 4-3
Power supply, A-2
POWER switch, 5-4
System disassembly and reassembly
removing the diskette drive and carrier
assembly, 4-48
Problems
application software, 5-13
beep code, 5-11
bootable CD-ROM not detected, 5-14
CD-ROM drive activity light, 5-13
characters distorted, 5-12
diskette drive activity LED, 5-13
network, 5-14
removing the front door and front door hinge
(tower-based system), 4-50
removing the front panel, 4-51
removing the hot-swap HDD bay, 4-53
removing the hot-swap SCSI backplane, 4-54
removing the intrusion switch assembly, 4-65
removing the non-hot-swap power supply, 4-
34
no characters on screen, 5-12
PCI installation tips, 5-14
power LED, 5-11
removing the system board, 4-58
removing the tower feet, 4-62
T
system cooling fans, 5-12
Temperature, A-2
R
Troubleshooting checklists, 5-5
RAID
U
controller configuration, 3-21
Real-time clock
running SSU to configure settings, 4-12
Real-time clock/calendar
replacing the battery, 4-10
Unpacking
system, 2-3
Upgrading your system
installing a RAID controller board, 4-45
installing and removing DIMMs, 4-20
installing or swapping a hard disk drive, 4-25
installing the optional hot-swap power
supply, 4-30
modifying the system board, 4-10
removing and installing a processor, 4-13
removing the side access panel, 4-5
replacing the real-time clock/calendar battery,
4-10
S
SCSISelect utility
adaptec, 3-17
Security menu
configuring in setup, 3-11
SERVER
RESET, 5-3
Server menu
configuring in setup, 3-12
Setup
tools recommended, 4-4
Using the system, 2-5
advanced menu, 3-7
exit menu, 3-16
integrated peripheral configuration menu, 3-8
main menu, 3-5
security menu contents, 3-11
server menu, 3-12
Stabilizer, 1-4
STATUS lamp, 1-4, 5-23
Switches
DC power, 4-3
POWER, 5-4
System
configuring, 3-2
W
Warning
components might be hot, 4-3
power on/off switch, 4-3
Weight, A-2
Windows 2000
advanced information, B-4
installation assumption, B-3
installing display adapter driver, B-8
installing operating system software, B-5
overview, B-2
preparation, B-4
required diskettes, B-2
field replaceable units, 6-3
forcing a power shutdown, 2-8
powering off, 2-8
Index-2
Download from Www.Somanuals.com. All Manuals Search And Download.
xx
Download from Www.Somanuals.com. All Manuals Search And Download.
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
456-01673-000
Download from Www.Somanuals.com. All Manuals Search And Download.
|