P r i n t e d i n J a p a n
P a r t N o . 7 8 4 0 9 7 2 1
I t a s c a , I l l i n o i s 6 0 1 4 3 - 1 2 4 8
1 2 5 0 N . A r l i n g t o n H e i g h t s R o a d , S u i t e 5 0 0
N E C T e c h n o l o g i e s , I n c .
N E C M u l t i m e d i a T h e a t r e
NEC Multimedia Theatre
®
MultiSync MT830™/1030™
LCD Projector
User’s Manual
NEC Technologies
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Important Safeguards
These safety instructions are to ensure the long life of your LCD projector and
to prevent fire and shock. Please read them carefully and heed all warnings.
7. If installing the LCD projector on the ceiling:
a. The ceiling must be strong enough to support the LCD projector and the
installation must be in accordance with any local building codes.
Installation
1. For best results, use your LCD projector in a darkened room.
b. The LCD projector must be installed by qualified NEC service personnel.
2. Place the projector on a flat, level surface in a dry area away from dust and
moisture.
Power Supply
1. The LCD projector is designed to operate on a power supply of 100-120 or
220-240 V 50/60 HzAC. Ensure that your power supply fits this requirement
before attempting to use your LCD projector.
3. Do not place your LCD projector in direct sunlight, near heaters or heat
radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal components.
5. Handle your LCD projector carefully. Dropping or jarring can damage
internal components.
2. Handle the power cable carefully and avoid excessive bending. A damaged
cord can cause electric shock or fire.
6. Do not place heavy objects on top of the LCD projector.
3. If the LCD projector is not to be used for an extended period of time,
disconnect the plug from the power outlet.
Cleaning
Fire and Shock Precautions
1. Unplug the LCD projector before cleaning.
1. Ensure that there is sufficient ventilation and that vents are unobstructed to
prevent the build-up of heat inside your LCD projector. Allow at least 3
inches (10cm) of space between your LCD projector and a wall.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild
detergent. Never use strong detergents or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or
mar the lens.
4. Clean the air filter with a vacuum cleaner after every 100 hours of operation.
a. Clean the outside of the filter with a vacuum cleaner.
b. Do not use water or any other liquid to clean the air filter.
c. Do not operate your LCD projector without the air filter.
2. Prevent foreign objects such as paper clips and bits of paper from falling into
your LCD projector. Do not attempt to retrieve any objects that might fall into
your projector. Do not insert any metal objects such as a wire or screwdriver
into your LCD project. If something should fall into your projector, discon-
nect it immediately and have the object removed by a qualified NEC service
person.
Lamp Replacement
• Perform lamp replacement in accordance with the instructions on page 79.
3. Do not place any liquids on top of your LCD projector.
• Be sure to replace the lamp when the Status light comes on. If you continue
to use the lamp after 2000 hours of use, the lamp bulb may shatter, and pieces
of glass may be scattered in the lamp case. Do not touch them as the pieces of
glass may cause injury. If this happens, contact your NEC dealer for lamp
replacement.
• Do not look into the lens while the projector is on. Serious
damage to your eyes could result.
• Do not look into the laser pointer while it is on and do not point
the laser beam at another person. Serious injury could result.
• Allow a minimum of ONE minute to elapse between turning the lamp off and
on. High voltage is applied to the lamp immediately when the power is turned
on. Therefore turning the power off and quickly back on may shorten the life
of your lamp and result in damage to your LCD projector.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3
5
ATTENTION
Pour couper l'alimentation principale, s'assurer de retirer
la fiche de la prise de courant.
ATTENTION
RISQUE D’ELECTROCUTION NE PAS OUVRIR
La prise de courant murale doit être installée le plus près
possible de l'équipement, et doit être facilement acces-
sible.
ATTENTION
RAYONNEMENT LASER NE PAS
REGARDER DANS LE FAISCEAU
Ce symbole a pour but de prévenir l’utilisateur de la
présence d’une tension dangereuse, non isolée se
trouvant à l’intérieur de l’appareil. Elle est d’une
intensité suffisante pour constituer un risque
d’électrocution. Eviter le contact avec les pièces à
l’intérieur de cet appareil.
Ce symbole a pour but de prévenir l’utilisateur de la
présence d’importantes instructions concernant
l’entretien et le fonctionnement de cet appareil. Par
conséquent, elles doivent être lues attentivement
afin d’éviter des problèmes.
LONGUEUR D’ONDE: 645 nm (640-660 nm)
MAX. SORTIE: 1 mW
APPREIL A LASER DE CLASSE 2
Importantes précautions de sécurité
AVERTISSEMENT
Les points suivants sont des précautions de sécurité importantes destinées à
garantir une longue durée de service du projecteur à écran à cristaux liquides
(LCD) et afin d’éviter un incendie et des risques d’électrocution. S’assurer de
lire attentivement ces précautions de sécurité et respecter tous les
avertissements décrits ci-dessous.
AFIN DE REDUIRE LES RISQUES D’INCENDIE OU
D’ELECTROCUTION, NE PAS EXPOSER CET APPAREIL A LA
PLUIE OU A L’HUMIDITE. AUSSI, NE PAS UTILISER LA FICHE
POLARISEE AVEC UN PROLONGATEUR OU UNE AUTRE
PRISE DE COURANT SAUF SI CES LAMES PEUVENT ETRE
INSEREES A FOND. NE PAS OUVRIR LE COFFRET, DES
COMPOSANTES HAUTE TENSION SE TROUVENT A
L’INTERIEUR. LAISSER A UN PERSONNEL QUALIFIE LE
SOIN DE REPARER CET APPAREIL.
Installation
1. Pour un fonctionnement optimal, utiliser le projecteur à écran à cristaux
liquides (LCD) dans une pièce sombre.
2. Placer le projecteur à écran à cristaux liquides (LCD) sur une surface à niveau
et dans un endroit sec exempt de poussières et d’humidité.
3. Ne pas placer le projecteur à écran à cristaux liquides (LCD) en plein soleil,
près d’appareils ménagers ou d’autres appareils de chauffage.
DOC avis de conformation
DOC avis de conformation
Cet appareil numérique de la classe A respecte toutes les exigences du
Règlement sur le Matériel Brouilleur du Canada.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4
7
4. La fumée, la vapeur et l’exposition aux rayons directs du soleil risquent de
détériorer sérieusement les composantes internes.
3. Si le projecteur à écran à cristaux liquides (LCD) n’est pas utilisé pendant une
période prolongée, retirer la fiche de la prise secteur.
5. Eviter des manipulations brusques lors du déplacement du projecteur à écran
à cristaux liquides (LCD), car un choc violent pourrait endommager les
composantes internes.
Nettoyage
1. Débrancher le projecteur à écran à cristaux liquides (LCD) de la prise
d’alimentation avant le nettoyage.
6. Ne pas deposer d’objets lourds sur le dessus du projecteur à écran à cristaux
liquides (LCD).
2. Nettoyer régulièrement le coffret avec un chiffon doux. S’il y a des taches
tenaces, utiliser une solution d’un détergent doux. Ne jamais utiliser de
détergents puissants ou des solvants, tel que l’alcool ou un diluant pour
nettoyer le projecteur à écran à cristaux liquides (LCD).
7. Lors de l’installation du projecteur à écran à cristaux liquides (LCD) au
plafond, respecter les instructions suivantes.
a. Le plafond doit être suffisamment solide pour supporter le poids du
projecteur à écran à cristaux liquides (LCD) et il doit être installé selon
les codes de construction locaux.
3. Utiliser un appareil diffuseur chauffant ou du papier de nettoyage de lentille
disponible dans le commerce pour nettoyer la lentille.
b. Le projecteur à écran à cristaux liquides (LCD) doit être installé par un
personnel qualifié.
Ne pas frapper ou rayer la surface de la lentille, car des défauts risquent de se
produire sur la surface de la lentille.
Alimentation
4. Nettoyer le filtre à air toutes les 100 heures.
1. Le projecteur à écran à cristaux liquides (LCD) est conçu pour fonctionner à
100-120 ou 220-240VCA 50/60Hz. S’assurer que la tension d’alimentation
locale satisfait cette exigence avant d’utiliser le projecteur.
a. Nettoyer seulement l’extérieur avec un aspirateur.
b. Ne pas nettoyer le filtre à air avec de l’eau ou un liquide.
c. Ne pas utiliser le projecteur à écran à cristaux liquides (LCD) sans
le filtre à air.
2. Manipuler le câble d’alimentation avec précaution et éviter de le plier
excessivement. Un cordon endommagé risque de provoquer une
électrocution ou un incendie.
2. Eviter que des objets étrangers, des agrafes, des clous et du papier, par
exemple, pénètrent à l’intérieur du projecteur à écran à cristaux liquides
(LCD). Ne pas essayer de récupérer ces objets soi-même ou ne pas insérer des
objets métalliques, des fils et des tourne-vis, par exemple à l’intérieur du
projecteur à écran à cristaux liquides (LCD). Si un objet tombe à l’intérieur
du projecteur à écran à cristaux liquides (LCD), le débrancher
immédiatement et contacter un dépanneur qualifié pour retirer l’objet.
Remplacement de la lampe
• Effectuer le remplacement de la lampe suivant les instructions de la page
83.
• Assurez-vous de bien remplacer la lampe lorsque le voyant d’usure
s’allume. Si vous continuez d’utiliser la lampe après 2000 heures
d’utilisation, l’ampoule peut se briser et des brisures de verre peuvent être
éparpillées dans le compartiment de la lampe. Ne les touchez pas car elles
peuvent vous blesser. Dans ce cas, contactez votre revendeur NEC afin de
procéder au remplacement de la lampe.
3. Ne pas placer des liquides sur le dessus du projecteur à écran à cristaux
liquides (LCD).
• Ne regardez pas à l’intérieur de l’objectif lorsque le projecteur
est en marche. Vous risquez de vous blesser gravement aux
yeux.
• Attendez minimum UNE minute après avoir éteint la lampe avant de la
rallumer. Une haute tension est immédiatement appliquée à la lampe quand
celle-ci est mise sous tension. Par conséquent, éteindre, puis tout de suite
rallumer peut abréger la vie de votre lampe et endommager votre projecteur
LCD.
• Ne regardez pas à l’intérieur de la flèche laser lorsque celle-ci
est en marche et ne dirigez pas le rayon laser sur une autre
personne. Vous risquez de provoquer ue blessure grave.
Précautions pour éviter un incendie ou
une électrocution
1. Une ventilation appropriée doit être assurée afin d’éviter une accumulation de
chaleur à l’intérieur du projecteur à écran à cristaux liquides (LCD). S’assurer
que les trous de ventilation ne sont pas obstrués. Laisser un espace d’au moins
10 cm (quatre pouces) entre le projecteur à écran à cristaux liquides (LCD) et
les murs.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5
9
L I M I T E D W A R R A N T Y
®
2. Any product on which the serial number has been defaced, modified or
removed. NECTECH’S LIABILITY FOR ANY DEFECTIVE PRODUCT
IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT
AT OUR OPTION. REPLACEMENT PRODUCTS MAY BE NEW OR
‘LIKE NEW’.
NEC MultiSync LCD Projector
Products
NEC Technologies, Inc. (hereafter NECTECH) warrants this product to be free
from defects in material and workmanship under the following terms.
3. NECTECH SHALL NOT BE LIABLE FOR : Damage, deterioration or
malfunction resulting from:
HOW LONG IS THE WARRANTY?
Parts and labor are warranted for (2) two years from the date of the first customer
purchase. The lamp is warranted for 2000 hours of operating time or six months,
whichever comes first.
a. Accident, misuse, abuse, neglect, fire, water, lightning or other acts of
nature, unauthorized product modification, or failure to follow instruc-
tions supplied with the product.
WHO IS PROTECTED?
b. Repair or attempted repair by anyone not authorized by NECTECH.
c. Any shipment of the product (claims must be presented to the carrier).
d. Removal or installation of the product.
This warranty may be enforced only by the first purchaser.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as specified below, this warranty covers all defects in material or
workmanship in this product. The following are not covered by the warranty:
e. Any other cause which does not relate to a product defect.
1. Any product which is not distributed in the U.S.A. or Canada by NECTECH
or which is not purchased in the U.S.A. or Canada from an authorized
NECTECH dealer. For a listing of authorized dealers please contact
NECTECH at 800-836-0655.
4. Cartons, carrying cases, batteries, external cabinets, magnetic tapes, or any
accessories used in connection with the product.
WHAT NEC WILL COVER
We will pay labor and material expenses for covered items. But we will not pay
for the following:
1. Removal or installation charges.
2. Costs of initial technical adjustments (set-up), including adjustment of user
controls. These costs are the responsibility of the NECTECH dealer from
whom the product was purchased.
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN
THIS PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS
OF USE OF THE PRODUCT, LOSS OF TIME, COMMERCIAL LOSS;
OR
3. Payment of shipping charges.
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUEN-
TIAL OR OTHERWISE. SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITA-
TIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
HOW YOU CAN GET WARRANTY SERVICE
1. To obtain service on your product, consult the dealer from whom you
purchased the product.
2. Whenever warranty service is required, the original dated invoice (or a copy)
must be presented as proof of warranty coverage. Please be prepared to
describe or demonstrate the problem to your dealer.
HOW STATE LAW RELATES TO THE WARRANTY
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
3. For the name of the nearest NECTECH authorized service center, call
NECTECH at 800-836-0655.
FOR MORE INFORMATION, TELEPHONE 800-366-5213
LIMITATION OF IMPLIED WARRANTIES
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.
NEC TECHNOLOGIES, INC.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
EXCLUSION OF DAMAGES
NECTECH’S LIABILITY FORANY DEFECTIVE PRODUCT IS LIMITED
TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT OUR
OPTION. NECTECH SHALL NOT BE LIABLE FOR:
NOTE: All products returned to NECTECH for service MUST have
prior approval. To get approval, call NEC Technologies at
800-836-0655.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
6
T A B L E O F C O N T E N T S
11
1. Introduction
Introduction To The MultiSync MT830/1030 LCD Projector ......................................... 13
How Do You Get Started? ............................................................................................... 15
What’s In The Box? ........................................................................................................ 15
Getting To Know Your MultiSync MT830/1030 LCD Projector ..................................... 17
Front / Rear Features................................................................................................ 17
Side Features ........................................................................................................... 17
Top Features ............................................................................................................ 19
Terminal Panel Features ........................................................................................... 21
Remote Control Features ......................................................................................... 25
2. Installation
Setting Up Your MultiSync MT830/1030 LCD Projector ............................................... 31
Selecting A Location ................................................................................................ 32
Using ATabletop Or Cart......................................................................................... 33
Ceiling Installation ................................................................................................... 39
Reflecting The Image............................................................................................... 43
Rear Screen Projection ............................................................................................. 44
Wiring Diagram .............................................................................................................. 45
Connecting Your PC Or Macintosh Computer ................................................................ 47
Connecting Your Document Camera ............................................................................... 53
Connecting Your VCR Or Laser Disc Player .................................................................. 53
Connecting An External Monitor .................................................................................... 54
Connecting Your Computer To The Mouse Output Port .................................................. 55
3. Operation
General Controls ............................................................................................................. 57
Using The Menus ............................................................................................................ 59
Menu Descriptions & Functions ..................................................................................... 61
Source Menu (Source Icons) .................................................................................... 61
Image Adjust Menu(Sound And Picture Control Icons) ........................................... 63
Power Menu(Projector Control Icons) .................................................................... 67
Settings Menu(Maintenance Icons) .......................................................................... 69
Using the Viewer function ........................................................................................ 71
4. Maintenance
Replacing The Lamp ....................................................................................................... 79
Cleaning Or Replacing The Filter ................................................................................... 81
Remote Control Battery Installation ................................................................................ 82
5. Troubleshooting
Status Light Messages..................................................................................................... 87
Common Problems & Solutions...................................................................................... 89
6. Specifications
Optical ............................................................................................................................ 91
Electrical ......................................................................................................................... 92
Mechanical ..................................................................................................................... 92
D-Sub Pin Assignments .................................................................................................. 95
Timing Chart ................................................................................................................... 97
PC Control Command Reference .................................................................................... 99
Cable Connection .......................................................................................................... 103
12
Download from Www.Somanuals.com. All Manuals Search And Download.
7
1 I N T R O D U C T I O N
13
This section introduces you to your new MultiSync MT830 (SVGA)/
MT1030 (XGA) LCD Projector, provides a list of materials that comes
with your projector and describes the features and controls.
Features you’ll enjoy:
•
Simple set up and operation.
•
Hot air blown from the vents does not bother the audience during
your presentation since the vents are located on the front.
Congratulations OnYour Purchase Of The MultiSync
MT830/1030 LCD Projector
•
•
A high-performance 150 watt short arc high pressure lamp that delivers
1000 ANSI lumens (MT1030: 900 ANSI lumens) and is guaranteed for
2000 hours of service or six months, whichever comes first.
The MultiSync MT830/1030 is one of the very best LCD projectors
available today. The multiple LCD panels enable you to project
precise images up to 300 inches across (measured diagonally) from
your PC or Macintosh computer (desktop or notebook), VCR, DVD
player, document camera, or even a laser disc player.
A wireless remote control that operates the projector from any
angle.
•
•
A laser pointer that' s built into the remote control.
The power zoom control enables you to adjust the image to be
between 20 and 300 inches (measured diagonally).
You can use the projector on a tabletop or cart, you can permanently
mount it on a ceiling*1, or you can use MultiSync MT830/1030 LCD
Projector to project images from behind the screen. The remote
control can be used wirelessly or with a cable, and you can even use
the remote control with the built-in remote mouse receiver to operate
the mouse on your PC or Mac. But best of all, the MultiSync MT830/
1030 is an NEC LCD projector. That means you can depend on years
of reliable performance and crystal-clear presentations!
•
•
•
Keystone correction allows you to correct trapezoidal distortion
so that the image is square.
White balance control allows you to adjust the brightness and
contrast for each RGB color.
You can choose between video modes depending on your source:
"normal" for a typical picture, "natural" for true color reproduc-
tion, and "camera" for use with a document camera or low APL
picture.
•
•
The optional MT Viewer kit allows you to start your presentation
even when a PC is not available at the site.
•
The "image capture" enables you to use the entire picture as a
background image or to create slides (optional MT Viewer re-
quired).
The remote control can be used with or without a cable, and you
can even use the remote to operate your PC or Macintosh mouse
wirelessly from across the room with the built-in remote mouse
receiver.
•
•
An image can be projected from in front or behind a screen, and
the projector can even be installed on the ceiling.
•
•
•
You can control your MultiSync MT830/1030 LCD Projector
with a PC.
NEC Technologies' exclusive AccuBlend™ intelligent pixel
blending technology - an extremely accurate image compression
technology - offers a crisp image with SXGA (1280
ן 1024) resolution*3. You can select any point on the screen with the
pointer and enlarge the selected area.
The contemporary cabinet design is compact, easy to carry, and
complements any office, board room or auditorium.
Eight kinds of pointers are available for your presentation.
•
Supports most IBM VGA, SVGA, XGA*
2, SXGA(with
*1 Installing the MultiSync MT830/1030 LCD Projector on the
ceiling must be done by authorized NEC technicians.C o n s u l t
your NEC dealer for more information.
AccuBlend)*3, Macintosh, or any other RGB signals within a hori-
zontal frequency range of 15.754 to 85 kHz and a vertical frequency
range of 50 to 85 Hz. This includes NTSC, PAL, SECAM and
*2 An XGA image (1024
ן 768) is converted into a 800ן 600 crisp NTSC4.43 standard video signals.
image with NEC technology's AccuBlend.
*3 An SXGA image (1280
ן 1024) is converted into a 1024ן 768 Note: Composite video standards are as follows:
NTSC:
PAL:
U.S. TV standard for video in U.S. and Canada.
TV standard used in western Europe.
crisp image with NEC technology's AccuBlend.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
INTRODUCTION
14
Download from Www.Somanuals.com. All Manuals Search And Download.
8
15
How Do You Get Started?
The fastest way to get started is to take your time and do everything
right the first time. Take a few minutes now to watch the introductory
video and review the manual. This may save you hours later on. At the
beginning of each section of the manual you'll find an overview. If the
section doesn't apply, you can skip it.
Remote control
String and rivet
What’s In The Box?
Make sure your box contains everything listed. If any pieces are missing,
contact your dealer. Please save the original box and packing materials if
you ever need to ship your MultiSync MT830/1030 LCD Projector.
• NEC MultiSync MT830/1030 LCD Projector
• Remote Control With Built-In Laser Pointer And Cables
• Mouse Adapter for IBM PS/2 and Mac
• Serial Cable
• Signal Cable (15-Pin Mini D-Sub To 15-Pin Mini D-Sub Connector)
• Pin Adapter for Macintosh
• Power Cable
• Two AA Batteries
• Quick Connect Guide
Batteries (AA
ן 2) Pin adapter for
Macintosh
Remote cable
• Introductory Video
• User's Manual
• Accessory Catalog
• Registration Card
• String and rivet
MultiSyncMT
Mouse adapter (For IBM PS/2)
Mouse adapter (For Macintosh)
User’s manual
Registration card
830/10
30
MultiSyncMT
LCD Projector
Quick connect guide
Quick Connect e
Series
Serial cable
Signal cable
Power cable
Introductory video
Accessory catalog
(15-Pin Mini D-Sub To 15-Pin Mini D-Sub connector)
MT
MultiSync
1020
AccessaonrdieMs
T
820
INTRODUCTION
16
Download from Www.Somanuals.com. All Manuals Search And Download.
9
17
Getting To Know Your MultiSync
MT830/1030 LCD Projector
AC Input
Rear Features
Front Features
Plug the female end of the supplied
power cable here, and the male end
into a properly grounded outlet.
Remote Sensor
Built-In Speaker
Lens And Lens Cap
Remote Sensor
Built-In Speaker
(2W)
(2W)
Main Power Switch
Carrying Handle
AC IN
One-Touch
Tilt button
One-Touch
Tilt button
Slot for Kensington
MicroSaver Security System
Front Vent
Rear Feet
Front Feet
Right Side Features
Left Side Features
Connector Cap
Lamp Cover
Lamp Cover Set Screw
Remote Sensor
Carrying Handle
Remote Sensor
PC CONTROL MOUSE OUTPUT REMOTE
S–VIDEO INPUT
AUDIO
CONTROL
INPUT
RGB MONITOR OUTPUT
AUDIO
AUDIO
L/MONO
R
RGB INPUT
1
RGB INPUT
2
AUDIO
L/MONO
INPUT AUDIO
R
VIDEO
Filter Cover
Latch
Terminal Panel
Slot Cover for the Optional
MT Viewer Board.
INTRODUCTION
18
Download from Www.Somanuals.com. All Manuals Search And Download.
10
19
Top Features
1 Power Button
Use this button to turn the power on and off when the Main Power Switch is on and
the LCD projector is in standby.
2 Menu Button
Displays the on- screen menu.
ᮤ ᮣ
3 Select (▲▼
) / (+)(–) Buttons
Select:
After you press the “Menu” button, use the ▲ or ▼ button to select the
menu icon of the item you wish to adjust.
ᮤ ᮣ
(▲▼
)
(+)(–):
Use these buttons while you' re in the Image Adjust mode to change the
level of a selected menu item. These buttons are also used to set an item
in the Power or Settings menus.
4 Enter Button
Executes your menu selection.
5 (+) (–) Zoom Buttons
Press the (+) button to make the image larger; press (–) to make the image smaller.
6 (+) (–) Focus Buttons
Press the (+) or (–) buttons to focus an image.
7 Power Indicator
MENU
2
3
SELECT
When this indicator is green, the LCD projector is on; when the indicator is amber, it
is standing by.
–
+
8 Status Indicator
ENTER
4
6
8
7
When this is lit red continually, it's warning you that the projection lamp has exceed
2000 hours of service. After this light appears, it is advisable to replace the projection
lamp as soon as possible.(See pages 79 and 80)
STATUS
POWER
+
+
–
–
ON/OFF
In addition the message "LAMP USAGE XX HOURS" appears continually when
the on-screen menu is not displayed.
If this light blinks red rapidly, it indicates that either the lamp cover or filter cover is
not attached properly. See the Status Light Messages on pages 87 and 88 for more
details.
ZOOM FOCUS
5
1
INTRODUCTION
20
Download from Www.Somanuals.com. All Manuals Search And Download.
11
21
Terminal Panel Features
This panel is located on the left side and is where you connect your cables.
1 S-Video Input
1
3
Here is where you connect the S-Video input from an external
source like a VCR.
Left Channel/Mono Audio Input Jack
This is your left channel audio input for stereo sound coming from
S-Video equipment or audio system. This also serves as your
monaural audio input.
REMOTE
CONTROL
INPUT
PC CONTROL MOUSE OUTPUT
S–VIDEO INPUT
AUDIO
RGB MONITOR OUTPUT
AUDIO
AUDIO
L/MONO
R
Right Channel Audio Input Jack
This is your right channel audio input for stereo sound.
RGB INPUT
1
RGB INPUT
2
AUDIO
L/MONO
INPUT AUDIO
R
VIDEO
NOTE: S-Video provides more vivid color and higher resolution
than the traditional composite video format.
2
4
2 Video Input
Connect a VCR, DVD player, laser disc player, or document camera
here to project video.
Left Channel/Mono Audio Input Jack
This is your left channel audio input for stereo sound coming from
video equipment or audio system. This also serves as your monaural
audio input.
Right Channel Audio Input Jack
This is your right channel audio input for stereo sound.
3 RGB Monitor Output Connector (Mini D-Sub 15 pin)
You can use this connector to loop your computer image to an
external monitor from either the RGB 1 or RGB 2 input source.
Audio Output Mini Jack
Connect additional external speakers here to listen to audio coming
from your computer, Video or S-Video input.
4 RGB Input 1 Connector (Mini D-Sub 15 pin)
Connect your PC or other RGB equipment such as IBM or compat-
ible computers. Use the signal cable that's supplied to connect to a
PC. Or connect a Macintosh or compatible computer here using the
signal cable and the pin adapter that is supplied.
RGB 1 Audio Input Mini Jack
This is where you connect RGB audio output from a computer or
another RGB source.
INTRODUCTION
22
Download from Www.Somanuals.com. All Manuals Search And Download.
12
23
5 RGB Input 2 Connector (Mini D-Sub 15 pin)
Connect a Macintosh or compatible computer here using the signal
cable and the monitor adapter that is supplied. Or connect your PC
or other RGB equipment such as IBM or compatible computers.
Use the signal cable that is supplied to connect to a PC.
6
7
8
REMOTE
CONTROL
INPUT
PC CONTROL MOUSE OUTPUT
S–VIDEO INPUT
AUDIO
RGB 2 Audio Input Mini Jack
RGB MONITOR OUTPUT
AUDIO
AUDIO
L/MONO
R
This is where you connect a second RGB audio output from a
computer or another RGB source.
RGB INPUT
1
RGB INPUT
2
AUDIO
6 PC Control Port
L/MONO
INPUT AUDIO
R
VIDEO
Use this port to connect your PC to control the MultiSync MT830/
1030 Projector. This enables you to use your PC and serial commu-
nication protocol to control the projector. If you are writing your
own program, command references are on pages 99 to 102.
5
A cap is put on the port at the factory. Remove the cap when using
the port.
7 Mouse Output Port
Use this port to operate your computer’s mouse functions from the
NEC MultiSync MT830/1030 remote control. When your com-
puter is connected here, the remote sensors on the LCD projector
cabinet will receive your mouse commands.
8 Remote Control Jack
Connect your remote control cable here for wired operation.
9 Built-in Security Slot (
)
This security slot supports the MicroSaver® Security System.
MicroSaver® is a registered trademark of Kensington Microware
AC IN
Inc. The logo
Microware Inc.
is trademarked and owned by Kensington
9
INTRODUCTION
24
Download from Www.Somanuals.com. All Manuals Search And Download.
13
25
Remote Control Features
1
3
You can use your remote control with the cable or wireless to operate
your MultiSync MT830/1030 LCD Projector. With the mouse output
port connected to your computer, you can also use the projector's
remote control to operate your computer's mouse wireless. (See pages
55 and 56 to connect your computer to the mouse output port.)
If you want to use your remote control with the cable, connect one end
of the cable to the jack on the remote control and the other end to the
Terminal Panel.
2
4
5
NOTE: If you are using a Macintosh computer, you can click either the
right or left button to activate the mouse.
OFF
ON
POWER
VIDEO S-VIDEO
1 Left Click Button
6
7
8
9
Use this button to enter your menu selection. It works the same as
the "Enter" button on the cabinet.
PC CARD
RGB 2
RGB 1
10
2 Laser Pointer
MENU
LASER
Beams a laser light when "Laser" button is pressed.
3 InfraredTransmitter
Direct the remote control toward the remote sensor on the projector
cabinet.
–
+
4 LED
R-CLICK/CANCEL
POINTER PIC-MUTE FREEZE
Flashes when any button is pressed.
5 Power On And Off
If your main power switch is turned on, you can use this button to
turn your MultiSync MT830/1030 LCD Projector on and off.
MAGNIFY SLIDE VOLUME
+
–
+
–
+
–
6 Video Button
Press to select an NTSC, PAL, SECAM or NTSC4.43 compatible
video source from a VCR, DVD player, laser disc player or docu-
ment camera.
ZOOM FOCUS KEYSTONE
+
+
+
–
–
–
7 S-Video Button
Press to select an S-Video source from a VCR.
8 RGB 1 Button
Press to select a video source from a computer connected to your
RGB 1 port.
9 RGB 2 Button
Press to select a video source from a computer connected to your
RGB 2 port.
10 PC Card Button
Press to display a slide from the flash memory card inserted in the
PC card slot of your LCD projector. (You must first install the
optional MT Viewer board into your LCD projector.)
INTRODUCTION
26
Download from Www.Somanuals.com. All Manuals Search And Download.
14
27
11 Laser Button
Press and hold this button to activate the laser pointer. When lit, you
can use the laser to draw your audience's attention to a red dot that
you can place on any object within 30 feet (10 m).
OFF
ON
POWER
VIDEO S-VIDEO
12 Menu Button
Use this button to call up the On-Screen Menu so you can adjust and
set the image. After you press this button, it will light up. During
this time you can use the mouse pad and right/left click buttons to
make menu selections.
PC CARD
RGB 2
RGB 1
MENU
LASER
If no buttons are pressed within 10 seconds while it illuminates, the
light goes out. To return to the main menu from a submenu, press
this button again.
12
13
11
14
ᮤ ᮣ
13 Mouse Pad(▲▼
/+ -)
–
+
Works as a mouse for your projected computer image. This pad is
also used to adjust position.
This pad selects the submenu you want to adjust. (See page 59.)
After you make your on-screen menu selection, use this pad to
adjust the level up or down. (See page 59.)
R-CLICK/CANCEL
POINTER PIC-MUTE FREEZE
17
15
16
14 Right Click/Cancel Button
Press this button to exit "Menus" or "Pointer."
MAGNIFY SLIDE VOLUME
+
–
+
–
+
–
18
ZOOM FOCUS KEYSTONE
+
+
+
15 Freeze Button
–
–
–
This button will freeze a picture. Press again to resume motion.
16 Picture Mute Button
This button turns off the image for a short period of time. Press
again to restore the image.
17 Pointer Button
Use this button to move your Pointer icon to the area you want on
the screen, then press the Magnify button on the remote control to
enlarge the selected area on the screen.
When you're finished, the "Pointer" button will remain lit for 10
seconds.
NOTE:
* Eight kinds of Pointers (icons) are available. You can select one
from the Settings Menu. The magnifying glass icon is selected at
the factory. See page 70 for more details.
* With the Pointer button pressed, the Mouse Pad is used to move
the picture.
18 Volume Button
Press (+) to increase the volume and (-) to decrease it.
INTRODUCTION
28
Download from Www.Somanuals.com. All Manuals Search And Download.
15
29
19 Slide Button
Press (+) to advance the next file or slide and (-) to return to the
previous file or slide. (the optional MT Viewer board required)
OFF
ON
POWER
20 Magnify Button
VIDEO S-VIDEO
Use the (+) or (-) button to adjust the image size up to 400%.
When the Pointer is displayed, the magnified image is displayed at
the center of the Pointer.
PC CARD
RGB 2
RGB 1
When the Pointer is not displayed, the magnified image is displayed
at the center of the screen.
MENU
LASER
21 Keystone Button
Press the (+) or (-) button to correct the keystone (trapezoidal)
distortion, and make the image square.
–
+
22 Focus Button
Press the (+) or (-) button to adjust the focus.
23 Zoom Button
Press the (+) button to zoom in and the (-) button to zoom out.
R-CLICK/CANCEL
POINTER PIC-MUTE FREEZE
24 Remote Jack
Connect your remote control cable here for wired operation.
19
NOTE: You cannot use Menu and Pointer at the same time.
MAGNIFY SLIDE VOLUME
+
–
+
–
+
–
20
23
ZOOM FOCUS KEYSTONE
+
+
+
21
22
Remote Control Precautions
–
–
–
•
•
•
Do not look into the laser pointer while it is on.
Do not point the laser beam at a person.
When the cable is connected to the remote control, it will not work
in the wireless mode.
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
If you will not be using the remote control for a long time, remove the
batteries.
24
•
Do not mix new and old or different types of batteries.
INTRODUCTION
30
Download from Www.Somanuals.com. All Manuals Search And Download.
16
2 I N S T A L L A T I O N
31
This section describes how to set up your MultiSync MT830/1030 LCD
projector and how to connect video and audio sources.
Setting Up Your MultiSync MT830/1030 LCD
Projector
Your MultiSync MT830/1030 LCD Projector is simple to set up and use. But
before you get started, you must first:
Attaching the lens cap to the lens hood
with the supplied string and rivet.
Lens cap
1. Determine the image size
2. Set up a screen or select a non-glossy white wall onto which you can project
your image.
Carrying The LCD Projector Always carry your LCD projector by the
handle. Ensure that the power cord and any other cables connecting to video
sources are disconnected before moving the projector. When moving the
projector or when it is not in use, cover the lens with the lens cap.
String
Rivet
Selecting A Location The further your LCD projector is from the screen or
wall, the larger the image. The minimum size the image can be is approxi-
mately 20" (0.5 m) measured diagonally when the projector is roughly 3 feet
(1.0 m) from the wall or screen. The largest the image can be is 300" (7.6 m)
when the projector is about 40.03 feet (12.2 m) from the wall or screen.
Projection Distance and Image Size
350
300
250
200
300”
235”
WIDE
150
100
TELE
50
27”
Projection distance
Width
20”
0
0.0
6.56
(2.0)
13.12
(4.0)
19.69
(6.0)
26.25
(8.0)
32.81
(10.0)
40.03 ft.
(12.2) (m)
Throw Distance
Screen size
Height
(diagonal)
INSTALLATION
32
Download from Www.Somanuals.com. All Manuals Search And Download.
17
33
Using A Tabletop Or Cart
(A) Top view
1. Place your LCD projector on a flat level surface at the optimal
distance from the screen or wall so you realize the size image you
want. (Avoid having bright room lighting or sun light directly on the
screen or wall where you'll be projecting the image.)
screen
2. Connect the power cable, remove the lens cap and turn the projector
on. (If no input signal is available, the projector will display a
background image.)
3. Ensure that the projector is square to the screen.
(B) Side view
4. Move the projector left or right to center the image horizontally on
the screen. (A)
screen
5. To center the image vertically (B), lift the front edge of the projector
and press the buttons on the front of the projector, just above the
feet, to release the one-touch tilt feet. (There is approximately 10.5˚
of up and down adjustment for the front of the projector. )
6. If a trapezoidal distortion appears on the screen, use the KEY-
STONE button on the remote control or select Keystone from the
menu to correct the distortion.
If necessary, adjust the front or rear feet so that the lens surface is
parallel to the screen. If you use the projector with the screen tilted,
the picture will be distorted. Each of the rear feet height can be
changed up to 0.6" (4 mm).
7. Increase or reduce the size of the projected image by pressing the
"Zoom" (+) or (–) buttons on the remote control or top of the
cabinet.
INSTALLATION
34
Download from Www.Somanuals.com. All Manuals Search And Download.
18
35
Distance Chart
Formulas(mm)
"H=Horizontal Screen Width
M=1.25H/33.02(Projection magnification)
A=C/cosα
C (WIDE)=53.2
ן M-85.609 C (TELE)=C(WIDE)
ן 1.3055 D ={(3H/8)-(92.2+8M)}
=1.906M-92.2
C
A
E=92.2+8M
Formulas(inch)
"H=Horizontal Screen Width
M=1.25H/1.3(Projection magnification)
A=C/cosα
C (WIDE)=2.09445
ן M-3.37 C (TELE)=C(WIDE)
ן 1.3055 D ={(3H/8)-(92.2+8M)}/25.4
=(1.906M-92.2)/25.4
α
E
D
E=(92.2+8M)/25.4
A : Distance between the lens and the screen center
C : Horizontal throw distance between the screen surface and the lens
D : Vertical distance between the projector bottom and the bottom of image
E : Vertical distance between the projector bottom and the screen center
INSTALLATIDOoNwnload from Www.Somanuals.com. All Manuals Search And Download.
36
19
37
Standard Zoom Lens (Wide)
8.70
0.15128
0.98849
8.65
0.15041
0.98862
α
Degree
9.02
8.86
8.81
8.78
8.75
8.73
0.15181
8.67
0.15076
0.98857
8.64
8.63
8.62
8.61
β (sin= α)
γ (cos= α)
0.15671 0.15395 0.15318 0.15260 0.15216
0.15024 0.14998 0.14984 0.14972
0.98865 0.98869 0.98871 0.98873
0.98764 0.98808 0.98820 0.98829 0.98836 0.98841
96
144
180
80
120
150
Screen Size
H–Width
inch
inch
32
40
48
60
56
70
64
80
72
90
160
200
192
240
216
270
240
300
120
100
4 : 3 Diagonal
4884
192.3
4828
190.1
84
3.30
831
32.7
7369
290.1
7285
286.8
172
6.77
1201
47.3
A
C
D
E
mm
inch
mm
inch
mm
inch
mm
inch
1572 2400 2814 3228 3642 4056
159.7
1552 2371 2781 3190 3600 4009
6127
241.2
6057
238.4
128
5.03
1016
40.0
8197 9853 11096 12338
322.7 387.9 436.8 485.7
8104 9742 10970 12199
319.1 383.5 431.9 480.3
61.9
94.5 110.8 127.1 143.4
61.1
-34
93.4 109.5 125.6 141.7 157.8
55
-4
10
25
40
201
260
304
348
-1.32 -0.16
0.41
523
20.6
0.99
585
23.0
1.57
646
25.4
2.15
708
27.9
7.92 10.23 11.96 13.70
1324 1570 1755 1939
339
462
13.3
18.2
52.1
61.8
69.1
76.4
1.98
1.99
C/H-Width
1.91
1.94
1.95
1.96
1.97
1.97
1.99
1.99
2.00
2.00
2.00
92.36
138.55
153.94 184.73 207.82 230.91
76.97
115.45
magnification
30.79 46.18 53.88 61.58 69.27
Standard Zoom Lens (Tele)
6.69
0.11643
0.99320
6.65
0.11576
0.99328
6.71
6.66
0.11603
0.99325
α
Degree
6.93
6.81
6.77
6.75
6.73
6.64
6.63
6.62
6.62
β (sin= α)
γ (cos= α)
0.12065 0.11850 0.11790 0.11746 0.11711 0.11684
0.99269 0.99295 0.99302 0.99308 0.99312 0.99315
0.11562 0.11542 0.11531 0.11522
0.99329 0.99332 0.99333 0.99334
96
144
180
Screen Size
H–Width
inch
inch
32
40
48
60
56
70
64
80
72
90
80
120
150
160
200
192
240
216
270
240
300
120
4 : 3 Diagonal
100
6346
249.9
6303
248.2
84
3.30
831
32.7
9575
377.0
9511
374.4
172
6.77
1201
47.3
5270
7961
313.4
7907
311.3
128
5.03
1016
40.0
A
C
D
E
mm
inch
mm
inch
mm
inch
mm
inch
2041 3118 3656 4194 4732
10651 12804 14418 16032
419.3 504.1 567.6 631.2
10580 12718 14322 15925
416.5 500.7 563.8 627.0
80.4 122.7 143.9 165.1 186.3 207.5
2027 3096 3630 4165 4699 5234
206.1
55
2.15
708
27.9
79.8 121.9 142.9 164.0 185.0
-34
-4
10
25
40
201
260
304
348
-1.32 -0.16
0.41
523
20.6
0.99
585
23.0
1.57
646
25.4
7.92 10.23 11.96 13.70
1324 1570 1755 1939
339
462
13.3
18.2
52.1
61.8
69.1
76.4
2.58
2.60
2.58
2.59
C/H-Width
2.49
2.54
2.55
2.56
2.57
2.60
2.61
2.61
2.61
92.36
138.55
153.94 184.73 207.82 230.91
magnification
30.79 46.18 53.88 61.58 69.27 76.97
115.45
INSTALLATIDOoNwnload from Www.Somanuals.com. All Manuals Search And Download.
38
20
39
WARNING
•
•
Only use your LCD projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector
severely damaged.
Do not use the LCD projector where temperatures vary greatly. The projector must be used at temperatures between 32˚F
(0˚C) and 104˚F (40˚C).
•
•
Do not expose the LCD projector to moisture, dust, or smoke. This will harm the screen image.
Ensure that you have adequate ventilation around your LCD projector so heat can dissipate. Do not cover the vents on the side
or the front of the projector.
Ceiling Installation
Installing your MultiSync MT830/1030 LCD Projector on the ceiling must be done by a qualified technician. Contact your
NEC dealer for more information.
Do not attempt to install the projector yourself.
NOTE : Distances may vary ±5%.
Formulas(mm)
"H=Horizontal Screen Width
M=1.25H/33.02(Projection magnification)
A=C/cosα
F
B=85.2+8M
α
B
C(WIDE)=53.2
ן M-85.609 C(TELE)=C(WIDE)
ן 1.3055 F={(3H/8)-(85.2+8M)}
=1.906M-85.2
Formulas(inch)
A
"H=Horizontal Screen Width
M=1.25H/1.3(Projection magnification)
A=C/cosα
B=(85.2+8M)/25.4
C
C(WIDE)=2.0945
ן M-3.37 C(TELE)=C(WIDE)
ן 1.3055 F={(3H/8)-(85.2+8M)}/25.4
=(1.906M-85.2)/25.4
A : Distance between the lens and the screen center
B : Vertical distance between the top of the optional ceiling mount and the screen center
C : Horizontal throw distance between the screen surface and the lens
F : Vertical distance between the projector bottom and the top of image
INSTALLATION
40
Download from Www.Somanuals.com. All Manuals Search And Download.
21
41
Standard Zoom Lens (Wide)
8.70
0.15128
0.98849
8.65
0.15041
0.98862
α
Degree
9.02
8.86
8.81
8.78
8.75
8.73
8.67
0.15076
0.98857
8.64
8.63
8.62
8.61
β (sin= α)
γ (cos= α)
0.15671 0.15395 0.15318 0.15260 0.15216 0.15181
0.98764 0.98808 0.98820 0.98829 0.98836 0.98841
0.15024 0.14998 0.14984 0.14972
0.98865 0.98869 0.98871 0.98873
96
144
180
Screen Size
H–Width
inch
inch
32
40
48
60
56
70
64
80
72
90
80
120
150
160
200
192
240
216
270
240
300
120
4 : 3 Diagonal
100
4884
192.3
824
32.4
4828
190.08
91
7369
290.1
1194
47.0
7285
286.81
179
A
B
C
F
mm
inch
mm
inch
mm
inch
mm
inch
1572 2400 2814 3228 3642 4056
6127
241.2
1009
39.7
6057
238.45
135
8197 9853 11096 12338
322.7 387.9 436.8 485.7
1317 1563 1748 1932
61.9
332
94.5 110.8 127.1 143.4 159.7
455
516
578
639
701
13.1
17.9
20.3
22.7
25.2
27.6
51.8
61.5
68.8
76.1
1552 2371 2781 3190 3600 4009
61.11 93.36 109.48 125.60 141.72 157.84
8104 9742 10970 12199
319.05 383.54 431.90 480.27
-27
3
17
32
47
62
208
8.2
267
10.5
311
12.2
355
14.0
3.6
7.0
-1.0
0.1
0.7
1.3
1.8
2.4
5.3
1.98
1.99
C/H-Width
1.91
1.94
1.95
1.96
1.97
1.97
1.99
1.99
2.00
2.00
2.00
92.36
138.55
153.94 184.73 207.82 230.91
magnification
30.79 46.18 53.88 61.58 69.27 76.97
115.45
Standard Zoom Lens (Tele)
6.69
0.11643
0.99320
6.65
0.11576
0.99328
α
Degree
6.93
6.81
6.77
6.75
6.73
6.71
6.66
0.11603
0.99325
6.64
6.63
6.62
6.62
β (sin= α)
γ (cos= α)
0.12065 0.11850 0.11790 0.11746 0.11711 0.11684
0.11562 0.11542 0.11531 0.11522
0.99329 0.99332 0.99333 0.99334
0.99315
80
0.99269 0.99295 0.99302 0.99308 0.99312
96
144
180
Screen Size
H–Width
inch
inch
32
40
48
60
56
70
64
80
72
90
120
150
160
200
192
240
216
270
240
300
120
4 : 3 Diagonal
100
6346
249.9
824
32.4
6303
248.15
91
9575
377.0
1194
47.0
9511
374.43
179
A
B
C
F
mm
inch
mm
inch
mm
inch
mm
inch
2041 3118 3656 4194 4732 5270
80.4 122.7 143.9 165.1 186.3 207.5
7961
313.4
1009
39.7
7907
311.29
135
10651 12804 14418 16032
419.3 504.1 567.6 631.2
1317 1563 1748 1932
701
332
455
516
578
639
13.1
17.9
20.3
22.7
25.2
27.6
51.8
61.5
68.8
76.1
2027 3096 3630 4165 4699 5234
10580 12718 14322 15925
416.52 500.71 563.85 626.99
206.06
62
79.78 121.88 142.92 163.97 185.02
-27
3
17
32
47
208
8.2
267
10.5
311
12.2
355
14.0
3.6
7.0
-1.0
0.1
0.7
1.3
1.8
2.4
5.3
2.58
2.60
C/H-Width
2.49
2.54
2.55
2.56
2.57
2.58
2.59
2.60
2.61
2.61
2.61
92.36
138.55
magnification
30.79 46.18 53.88 61.58 69.27 76.97
115.45
153.94 184.73 207.82 230.91
INSTALLATIDOoNwnload from Www.Somanuals.com. All Manuals Search And Download.
42
22
43
If your projector is mounted on the ceiling and your image is upside down, use
the “Menu” and “Select” buttons on your projector cabinet or (▲) (▼) buttons
on your remote control to correct the orientation. (See page 70.)
Reflecting The Image
Using a mirror to reflect your LCD projector's image enables you to enjoy a
much larger image. Contact your NEC dealer if you need a mirror.
If you're using a mirror and your image is inverted, use the “Menu” and
“Select” buttons on your projector cabinet or (▲) (▼) buttons on your remote
control to correct the orientation. (See page 70.)
Mirror
Screen
Rear Screen Projection
You can use your MultiSync MT830/1030 LCD projector to project an image
from the rear onto a transparent screen. The distance the projector must be
from the screen is the same as if you were projecting the image from the front.
Contact your NEC dealer if you need a transparent screen.
If you're projecting the image from the rear and your image is inverted, use the
“Menu" and "Select" buttons on your projector cabinet or (▲) (▼) buttons on
your remote control to correct the image. (See page 70 .)
INSTALLATIDOoNwnload from Www.Somanuals.com. All Manuals Search And Download.
44
23
45
Wiring Diagram
To video, S-video, and
audio inputs on the LCD
Projector.
VCR, DVD Player or LaserDisc Player
Monitor
REMOTE
CONTROL
INPUT
PC CONTROL MOUSE OUTPUT
S–VIDEO INPUT
AUDIO
RGB MONITOR OUTPUT
AUDIO
AUDIO
L/MONO
R
RGB INPUT
1
RGB INPUT
2
AUDIO
L/MONO
INPUT AUDIO
R
VIDEO
Remote cable
Mouse adapter (For Macintosh)
Mouse adapter (For IBM PS/2)
Macintosh or Compatibles (Desk top type)
Pin adapter for Macintosh (supplied)
IBM VGA or Compatibles
Document Camera
Signal cable (supplied)
To mini D-Sub 15-pin connector on the LCD Projector.
Remote Control Guideline
1. Plug the serial cable with the mouse output port of the projector into your computer's mouse port and restart your computer to gain remote
mouse control.
2. When using the remote control's built-in infrared mouse on a laptop computer, the laptop's mouse, trackball or trackpad will be disabled.
Disconnect the serial cable from the mouse output port and restart your computer to regain trackball or trackpad mouse control.
3. If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management
software.
4. If you accidentally hit the OFF button on the remote control, wait one full minute and then press the ON button to resume.
INSTALLATION
46
Download from Www.Somanuals.com. All Manuals Search And Download.
24
47
3. Use the signal cable that's supplied to connect your PC or
Macintosh computer to the projector. For a Macintosh, use the
supplied pin adapter to connect to your Mac's video port.
Connecting Your PC Or Macintosh
Computer
Connecting your PC or Macintosh computer to your MultiSync
MT830 (SVGA) /1030 (XGA) Projector will enable you to project
your computer's screen image for an impressive presentation. All of
these following display standards are supported:
4. Turn on the projector and the computer.
5. If the projector goes blank after a period of inactivity, it may be
caused by a screen saver installed on the computer you've
connected to the projector.
VGA 640
ן 480 for graphics VGA 640
ן 350 for graphics VGA 720
ן 350 for text Macintosh at 640
ן 480 XGA1024
ן 768 VGA 640
ן 400 for graphics VGA 720
ן 400 for text SuperVGA 800
ן 600 Macintosh at 832
ן 624 Macintosh at 1024
ן 768 When using a Macintosh with the MT830/1030, set the DIP
switches of the supplied pin adapter according to your resolution.
After setting, restart your Macintosh.
See the following pages for setting of the DIP switches.
SXGA1280
ן 1024 (AccuBlend) •
When using with a Macintosh, XGA/VGA/SVGA is recom-
mended if your Macintosh supports this mode.
To connect to a PC, Macintosh or computer equipped with an XGA/
SVGA /VGA adapter or compatible graphics adapter, simply:
• When using with a Macintosh PowerBook, output may not be
set to 1024
ן 768 unless “mirroring” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh com-
puter for mirroring.
1. Turn off the power to your projector and computer.
2. If your PC does not support XGA/SVGA/VGA you will need to
install an XGA/SVGA/VGA graphics board. Consult your
computer's owner's manual for your XGA/SVGA/VGA configura-
tion. If you need to install a new board, see the manual that comes
with your new graphics board for installation instructions.
NOTE: A Video Adapter cable manufactured by Apple Computer
is needed for a PowerBook which does not have a mini D-Sub 15-
pin connector.
Settings for Monitor Mode
Number of DIP switch
S1 S2 S3 S4 S5 S6 S7 S8
Monitor size
ON
ON
ON
ON
ON
15” multi-scan mode /16”–13”
17” multi-scan mode /19”–13”
19” multi-scan mode /21”–13”
13” fixed mode /640
ן 480 VGA/SVGA mode
ON
ON
ON
ON
16” fixed mode /832
ן 624 19” fixed mode /1024
ן 768 ON
NOTE: For settings other than display modes supported by your
Macintosh and MT830/1030, use of the DIP switch may bounce a image
slightly or may display nothing. If this happens, set the DIP switch to the
13” fixed mode and then restart your Macintosh. After that, restore to a
displayable mode and then restart the Macintosh again.
Make sure that the MT830/1030 and your Macintosh are connected with
the pin adapter and the supplied signal cable (mini D-Sub 15-pin connec-
tor) and then restart your Macintosh.
INSTALLATIDOoNwnload from Www.Somanuals.com. All Manuals Search And Download.
48
25
49
Examples of DIP switch setting
13” fixed mode
17” multi-scan mode
VGA/SVGA mode
ON
ON
ON
1
2
3 4
5
6
7 8
1
2
3 4
5
6
7
8
1
2
3 4
5
6
7
8
NOTE: Refer to your computer's owner's manual for more information about your computer's video output requirements and any
special identification or configuring your projector's image and monitor may require.
Settings for Macintosh Adapter
Macintosh models applied
Setting Mode (Fixed resolution)
Setting required to be selected resolution
on Mac after restarting.
Desktop type and PowerBook with 16” fixed mode (output is 832
ן 624) Set to VGA/SVGA (800
ן 600) 800
ן 600 LCD panel PowerBook with 640
ן 480 LCD panel 13” fixed mode (output is 640ן 480) Set to 17” multi-scan mode (640
ן 480) Desktop type with AccuBlend
19” fixed mode (output is 1024
ן 768) Set to 17” multi-scan mode (1024ן 768) INSTALLATIDOoNwnload from Www.Somanuals.com. All Manuals Search And Download.
50
26
51
4. You may be asked to reboot for the changes to take affect, or you' ll
get a message that "Windows is about to resize your display." You' ll
be asked if you want to keep your settings. Select "Yes."
Changing Video Resolutions
Depending on your computer's graphic capability, you may be able
to select one of several resolutions. Generally a computer- either a
PC or Macintosh- with 1 meg. of memory will run:
640
ן 480 at 16.7 million colors (24 bit Truecolor) 800
ן 600 at 65 thousand colors. Method 2
1. Click on your "My Computer" icon.
2. Open "Control Panel" and select "Display."
3. Change your resolution and click "OK." after the new resolution is
selected.
4. You may be asked to reboot for the changes to take affect, or you' ll
get a message that "Windows is about to resize your display." You' ll
be asked if you want to keep your settings. Select "Yes."
1024
ן 768 at 256 colors. As the resolution increases, the number of colors you can run
decreases. With 2 meg. of memory a computer will run:
640
ן 480 at 16.7 million colors (24 bit Truecolor). 800
ן 600 at 16.7 million colors (24 bit Truecolor). 1024
ן 768 at 65 thousand colors. 1280
ן 1024 at 256 colors. Windows 3.1
1. Click on the "Main" icon and open "Control Panel."
2. Select "Change System Settings" and click on "Option."
3. Choose "Change Display Settings."
Windows 95
There are two methods you can use to change your resolution.
4. Select the resolution you want.
5. Choose the current drive or another.
Method 1
1. Move your cursor to the background image and click.
6. Restart Windows for the changes to take affect.
2. In the "Properties" menu, select "Settings."
3. Change your resolution and click "OK."
Macintosh
Notebook Computers And Resolution Standards
NEC projectors are designed to project industry standardized video
such as VESA (Video Electronics Standards Association) or VGA
(Video Graphics Array). Notebook computers do not use industry
standards. They use whatever timing is necessary to match their local
LCD display. The end result is typically not standards. By turning off
your notebook's display, the timing parameters are a bit more like the
real VESA or VGA signal.
1. Under the Apple menu, select "Control Panels" and open "Moni-
tors."
2. Click and open "Options."
3. Select your new resolution and click "OK."
If you have an NEC monitor connected to your Macintosh, you may
have a "DPI-On-The-Fly" extension that enables you to change your
resolution directly. The "DPI-On-The-Fly" icon is under your Apple
menu.
For an optimal projected image with a notebook computer, it is
recommended that you use the Auto mode. This feature is useful when
an XGA image (1024
ן 768) is displaying with a notebook computer supported by SXGA (1280
ן 1024) and when an SVGA image (800
ן 600) is displaying with a note book computer supported by XGA (1024
ן 768). See Source Menu on page 61 for more information.
INSTALLATION
52
Download from Www.Somanuals.com. All Manuals Search And Download.
27
53
Connecting Your Document Camera
You can connect your MultiSync MT830/1030 LCD Projector to a document camera. To do so, simply:
1. Turn off the power to your LCD projector and document camera.
2. Use a standard video cable to connect your document camera to the Video input on your projector.
3. Turn on the LCD projector and the document camera.
NOTE: Refer to your document camera's owner's manual for more information about your camera's video
output requirements .
Connecting Your VCR Or Laser Disc Player
Use common RCA cables (not provided) to connect your VCR or laser disc player to your MultiSync
MT830/1030 LCD Projector. To make these connections, simply:
1. Turn off the power to your LCD projector and VCR or laser disc player.
2. Connect one end of your RCAcable to the video output connector on the back of your VCR or laser disc
player, connect the other end to the Video input on your projector. Use standard RCA audio patch cords
to connect the audio from your VCR or laser disc player to your projector (if your VCR or laser disc
player has this capability). Be careful to keep your right and left channel connections correct for stereo
sound.
3. Turn on the LCD projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your
equipment's video output requirements.
Connecting An External Monitor
You can connect a separate, external monitor to your LCD projector to simultaneously view on a monitor
the image you're projecting. To do so:
1. Turn off the power to your LCD projector, monitor and computer, document camera or video source.
2. Use a 15-pin cable to connect your monitor to the RGB Monitor Output (Mini D-Sub 15 pin)
connector on your LCD projector.
3. Turn on the LCD projector, monitor and the computer, document camera or video source.
INSTALLATION
54
Download from Www.Somanuals.com. All Manuals Search And Download.
28
55
Connecting Your Computer to the
Mouse Output Port
The built-in remote mouse receiver enables you to operate your
computer's mouse functions from the NEC MultiSync MT830/1030
remote control. It is a great convenience for clicking through your
computer-generated presentations.
To connect the mouse output port:
1. Turn off your computer.
2. For PCs: Remove your current mouse and connect the serial
cable from the mouse output to your PC's mouse port. (Use the
6-pin adapter for connecting to a PS/2 computer.)
For Macintosh: Remove your current mouse from your com-
puter, attach the Macintosh adapter to the mouse output port’s
serial cable, and connect the LCD Projector to your mouse port.
3. When the built-in remote mouse receiver is available, it will
disable your regular mouse, disconnect the serial cable and
restart your computer.
Ⅵ The built-in Remote Mouse Receiver as a mouse for your computer
REMOTE
CONTROL
INPUT
S–VIDEO INPUT
AUDIO
RGB MONITOR OUTPUT
AUDIO
L/MONO
R
RGB INPUT
1
AUDIO
RGB INPU
AUDIO
IBM PC/AT
L/MONO
INPUT AUDIO
R
VIDEO
Serial cable (supplied)
REMOTE
CONTROL
INPUT
S–VIDEO INPUT
AUDIO
RGB MONITOR OUTPUT
AUDIO
AUDIO
L/MONO
R
Macintosh
IBM PS/2
RGB INPUT
1
RGB INPU
AUDIO
L/MONO
INPUT AUDIO
R
VIDEO
INSTALLATION
56
Download from Www.Somanuals.com. All Manuals Search And Download.
29
3 O P E R A T I O N
57
This section describes how to select a computer or video source and how to adjust
the picture and sound.
General Controls Before you turn on your MultiSync MT830/1030 LCD Projec-
tor, ensure that the computer or video source is turned on and that your lens cap is
removed.
1. Turn On The LCD Projector The main power switch is on the front panel of
the MultiSync MT830/1030 LCD Projector. By turning this switch on, the
projector will go into its standby mode and the power light will glow amber.
Only after you press the "On" button on the remote control or projector cabinet
will the power light turn to green and the projector become ready to use.
NOTE: To turn the LCD projector on and off with just the front panel switch,
use the menu and enable the "auto start" feature. (See page 67. )
2. Select The Computer, Video Source Or “Presentation Viewer” Press the
“Video” (VCR, document camera, or laser disc player), “S-video”, “RGB 1” or
“RGB 2” (computer) or PC CARD button on the remote control to display the
image. Or press the “Menu” button on the cabinet and use the icons to select
your video source: “Video”, “S-Video”, “RGB 1”, “RGB 2” or “PC CARD”.
3. Adjust The Image Size Press the "Zoom" button (+) or (-) on the remote control
or projector cabinet to make the image larger or smaller.
4. Focus Press the "Focus" button (+) or (-) on the remote control or projector
cabinet to focus the image.
5. Turning Off The Projector First press the "off" button on the remote control or
the projector cabinet. The power light will glow amber. Then turn off the main
power switch on the front panel. The power light will go out.
IMPORTANT:
•
The LCD projector should be unplugged if it will not to be used for an extended
period.
•
To turn off the image briefly (five minutes or less), use the "Picture Mute" button
instead of turning the projector off and on.
•
•
The LCD projector will display a black or blue image if no input signal is present.
Do not turn the LCD projector off and then immediately back on. The projector
needs to cool for a minute before it can be restarted.
OPERATION
58
Download from Www.Somanuals.com. All Manuals Search And Download.
30
59
Using The Menus
1. Press the "Menu" button on the remote control or projector cabinet to display the Main Menu.
2. Press the "Select" button on the projector cabinet or (▲) (▼) buttons on your remote control to highlight the menu for the item you want
to adjust.
3. Press the "Enter" button on the projector cabinet or the "Left Click" button on the remote control to select a submenu or item.
4. Adjust the level or turn the selected item on or off by using the "Mouse pad" (+) or (–) buttons on the remote control or “Select” (+) or (–)
buttons on the cabinet. The on-screen gauge will show you the amount of increase or decrease. [The (+) button is "on" and (–) is "off".]
5. The change is stored until you adjust it again.
6. Repeat steps 2-5 to adjust an additional item, or press "Right-Click" on your remote control to quit the menu display.
PC CARD
VIDEO
RGB Auto Mode ON
RGB Auto Mode OFF
OPERATION
60
Download from Www.Somanuals.com. All Manuals Search And Download.
31
61
Menu Descriptions & Functions
Source Menu
Enables you to select a video source such as a VCR, DVD player, laser disc player, computer
or document camera depending on what is connected to your inputs. Press the "Select"
button on the projector cabinet or (▲) (▼) buttons on your remote control to highlight the
menu for the item you want to adjust
Video
Selects what is connected to your Video input-VCR, laser disc player, DVD player, or
document camera.
S-Video
Selects what is connected to your S-Video input-VCR, DVD player, or laser disc player.
RGB 1
Selects the computer connected to your RGB 1 input.
RGB 2
Selects the computer connected to your RGB 2 input.
NOTE: Normally select the Auto mode so that the LCD projector automatically can select
the appropriate resolution mode for your RGB source.
If you want to finely adjust the image or if the LCD projector fails to select the appropriate
resolution mode for the RGB source, turn the Auto mode off and select the Real mode on the
Resolution item.
PC CARD
This feature enables you to make a presentation using the Viewer function with the optional
MT Viewer board (VK-MT) installed.
Press the Mouse pad (+) or (-) buttons to select "Start" for the image you want to display
first and "Select File" for the file you want to select or "Select Slide" for the image you want
to slide.
OPERATION
62
Download from Www.Somanuals.com. All Manuals Search And Download.
32
63
Image Adjustment
Menu
Provides access to controls for your image and sound. Use the “Select” button on the projector cabinet or (▲)
(▼) buttons on your remote control to highlight the menu for the item you want to adjust.
The volume, image mode, keystone, brightness, contrast, color, tint and sharpness controls are available for
Video or S-Video sources.
The volume, image mode, keystone, brightness, contrast, white balance and auto mode controls are available for
RGB 1 or RGB 2 sources.
The volume, image mode and keystone controls are available for PC CARD.
Volume
Use the Mouse pad (+) or (–) buttons to adjust the volume.
૽
Image Mode
VIDEO/S-VIDEO ........ Use the Mouse pad (+) or (-) buttons to choose "Normal" for a regular picture, "Natural"
for true color reproduction, or "Document Camera" for a document camera or other low
APL picture.
RGB/ PC CARD ..... Use the Mouse pad (+) or (-) buttons to choose "Normal" when in a lighted room and
"Natural 1&2" when in a darkened room. 1 for better flesh tone; 2 for true reproduction of
middle tones.
Keystone
Use the Mouse pad (+) or (-) buttons to correct the keystone (trapezoidal) distortion to make the top of the
screen longer or shorter to be the same as the bottom.
NOTE: The maximum keystone angle that can be corrected is 23 degrees, including the optical offset 8 degrees.
NOTE: To save your keystone changes, select "Keystone Save" from the Power Menu.
Brightness
Use the Mouse pad (+) or (–) buttons to adjust the brightness.
Contrast
Use the Mouse pad (+) or (–) buttons to adjust the contrast.
૽૽
Color
Use the Mouse pad (+) or (–) buttons to adjust the color.
૽૽
Tint
Use the Mouse pad (+) or (–) buttons to adjust the tint.
૽૽
Sharpness
Use the Mouse pad (+) or (–) buttons to adjust the sharpness.
OPERATION
64
Download from Www.Somanuals.com. All Manuals Search And Download.
33
65
૽૽૽
White Balance
Use the Mouse pad (+) or (-) buttons to adjust the white balance. Brightness for each color (RGB) is used to
adjust the black level of the screen; Contrast for each color (RGB) to adjust the white level of the screen.
૽૽૽
Auto Mode
Use the Mouse pad (+) button to turn this feature on so "Horizontal Position", "Vertical Position", "Picture
Adjustment", "Fine Picture" and "Resolution" are made automatically. Usually set to ON.
When the Auto mode is turned off with the Mouse pad (-) button is turned off, you can adjust/set "Horizon-
tal Position", "Vertical Position", "Picture Adjustment", "Fine Picture" and "Resolution" manually.
૽૽૽
Horizontal Position
(when Auto Mode is off)
Use the Mouse pad (+) button to move the image right; (–) to move it left. This adjustment is made automati-
cally when the Auto mode is turned on.
૽૽૽
Vertical Position
(when Auto Mode is off)
Use the Mouse pad (+) button to move the image up; (–) to move it down. This adjustment is made automati-
cally when the Auto mode is turned on.
૽૽૽
Picture Adjustment
(when Auto Mode is off)
Use this icon with the “Fine Picture Adjustment” to fine tune the computer image or to remove any vertical
banding that might appear. This function adjusts the clock frequencies that eliminate the horizontal banding in
the image. Press the Mouse pad (+) and (–) buttons until the banding disappears. This adjustment may be
necessary when you connect your computer for the first time. This adjustment is made automatically when the
Auto mode is turned on.
૽૽૽
Fine Picture
(when Auto Mode is off)
Use this icon to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident
when part of your image appears to be shimmering.) Use the Mouse pad (+) and (–) buttons to adjust the
image. Use the Fine Adjustment only after the Picture Adjustment is complete. This adjustment is made auto-
matically when the Auto Mode is turned on.
૽૽૽
Resolution
(when Auto Mode is off)
When "Auto mode" is selected, the LCD projector automatically determines the best resolution for the current
RGB input signal to project an image using NEC's AccuBlend Intelligent Pixel Blending Technology.
Use the Mouse pad (–) button to turn off the Auto mode feature to enable the Resolution feature.
Selecting "Real" allows you to project a source in the real resolution (in the under scan mode) if:
* the LCD projector fails to determine automatically.
* you want to fine adjust an item such as phase.
* you want to project signals other than those with an aspect ratio 4 to 3.
NOTE: Even when you are in the Real mode, an SXGA image is displayed with AccuBlend Intelligent Pixel
Blending Technology.
NOTE:
ૺ
The Document Camera mode will not work with an RGB source.
ૺૺ Color, Tint, Sharpness and Image Mode controls will not work with an RGB source or PC Card. The
Tint control will not work with a PAL or SECAM source.
ૺૺૺ Horizontal and Vertical position controls, White Balance, Picture, Fine Picture and Auto Mode
adjustments will not work with a Video, S-Video source or PC card.
OPERATION
66
Download from Www.Somanuals.com. All Manuals Search And Download.
34
67
Power Menu
Provides access to Lamp Usage information and the Auto Start and Power Management fea-
tures. Use the “Select” button on the projector cabinet or (▲) (▼) buttons on your remote
control to access a submenu. Then press the Mouse pad (+) or (–) to choose a specific option.
Lamp Usage
This tells you how long the lamp has been in operation. It is recommended that you replace a
lamp after 2000 hours of service. After you install a new lamp, select this icon and press and
hold the “Power On” button on the remote control for ten seconds to reset the lamp clock back
to zero.
NOTE: The projector will turn off and go into stand by mode after 2100 hours of service. If
this happens, press the "Power Off" button on the remote control for ten seconds to reset the
lamp clock back to zero. Do this only after replacing the lamp.
Auto Start
Turns the LCD projector on automatically when the main power switch is turned on. This
eliminates the need to always use the “Power” button on the remote control or projector
cabinet. Press the Mouse pad (+) to turn this feature on and (–) to turn it off.
Power Management
When “Power Off” is on and there is no RGB video input for five minutes or more, the
projector will automatically turn itself off. Press the Mouse pad (+) to turn this feature on and
(–) to turn it off. This feature does not work with Video or S-Video sources.
Keystone Save
This enables you to save your current keystone settings. Saving your change once affects all
sources.
Use the Mouse pad (+) button to turn the feature on so you save the keystone adjustments;
(-) to turn the feature off so you can cancel them.
On Screen Mute
Use the Mouse pad (+) button to turn off the on screen ; (-) to restore it. The On screen Mute
feature is valid for turning on and switching inputs only.
OPERATION
68
Download from Www.Somanuals.com. All Manuals Search And Download.
35
69
Settings Menu
Enables you to set preferences and other operating options. Use the “Select” button on the projector cabinet or
(▲) (▼) buttons on your remote control to access the submenu you want.
Capture (with the optional viewer board installed only)
When the Capture is selected, press "Enter" on the projector cabinet or Left Click button on the remote control to
display "Execute" and "capture" an image from a source that is currently being displayed. When capturing is
completed, "Completed" is displayed under the Capture icon.
Unless a flash memory card is inserted into the slot of the viewer board, "No Card" is displayed. This means that
the Capture feature is not available. The "Card Error" display means that the free space of the flash memory card
is insufficient for saving images. Make more space available on the card by erasing unwanted images with your
PC. The number of images that can be captured depends on the size of the flash memory card.
NOTE: Be sure not to turn off the power or remove the flash memory card unless "Completed" is displayed.
Doing so could cause a loss of the data in the flash memory card or damage to the card itself.
Background
Use this feature to display a black or blue screen when no signal is available. Press the Mouse pad (+) or (–)
buttons to choose the back screen you want. Press "Enter" on the cabinet or the "Left Click" on your remote
control to save your change.
Video Standard
This feature enables you to select composite video standards M_NTSC manually. Normally select "Auto".
Use the Mouse pad (+) or (–) buttons to choose M_NTSC. Press "Enter" on the cabinet or the "Left Click" on
your remote control to save your change.
Projection
This reorients your image for your type of projection. Press the Mouse pad (+) or (–) button until it is correct.
Press “ENTER” on the cabinet or the “Left Click” on your remote control to save your change. The options are:
front floor projection, rear ceiling projection, rear floor projection, and front ceiling projection.
Language
Use the Mouse pad (+) or (–) to choose one of six languages for on-screen instructions. Press “ENTER” on the
cabinet or the “Left Click” on your remote control to save your change The options are: English, German,
French, Italian, Spanish and Swedish.
Pointer
This enables you to select from eight different Pointer icons for the "Pointer" button on your remote control. The
magnifying glass pointer is selected at the factory. Use the Mouse pad (+) or (-) buttons to choose one of the
eight Pointer icons. Press "Enter" on the cabinet or the "Left Click" on your remote control to save your change.
After moving your Pointer icon to the area you want on the screen, press the Magnify button on the remote
control to enlarge the selected area on the screen.
Reset
Changes all adjustments to the factory preset levels for each source individually. To activate, you must hold
down the Mouse pad (+) button on the cabinet or remote control for at least two seconds. The adjustments that
will be reset are white balance, horizontal and vertical control, picture and fine picture adjustment (for the
current source only), white balance, brightness, contrast, color, tint, and sharpness.
OPERATION
70
Download from Www.Somanuals.com. All Manuals Search And Download.
36
71
Using the Viewer function
If you use the Viewer function on the LCD projector, you must first
install the optional MT Viewer board (VK-MT) in the LCD projector
and set up the exclusive software included with the VK-MT kit.
See the user's manual included with the VK-MT for installing and
uninstalling the software.
2. Remove the two screws from the bottom.
Mounting the Optional MT Viewer Board
To install the Viewer board:
1. Set the LCD projector on end with the carrying handle up.
NOTE: Be sure to unplug the LCD projector before installing the Viewer board.
3. Remove the slot cover by pushing up on the catch of the cover
with a flat-head screwdriver until you feel it detach.
4. Insert the optional viewer board into the slot. Be sure to push the
board until the board is securely fitted.
6. Put the LCD projector back in the original position.
5. Secure the board in place with the two screws that you removed in
step 2.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
37
73
Projecting Slides
Orientation of flash memory card insertion
To Project the Slides (the presentation materials)
1. Insert a flash memory card into the PC card slot.
* To eject the flash memory card, press the Eject button.
The flash memory card has a front and a back side and the flash memory
card is designed to be inserted in only one orientation. The card is
designed so that it cannot be inserted in reverse, but trying to insert it
forcefully might break the pins inside the slot or ruin the flash memory
card slot. See the flash memory card manual for information about the
orientation of the flash memory card.
NOTE: Should the card be difficult to insert, do not forcefully push
the card in.
2. Select the PC card as a source.
* Press the Menu button on the remote control or projector cabinet
and select "PC CARD" from the Source menu.
PCMC IA-ATA
Flash Memory Card
* If there is no flash memory card in the card slot, the LCD projector
displays a blue back or black back image.
3. Select "Select File" or "Select Slide".
* Use the Mouse pad (+) or (-) button on the remote control to select
"Select File" or "Select Slide".
* The type of flash memory card required for use in the LCD projector
is a Type II PCMCIA-ATA flash memory card (not supplied). Never
use other types of PC card than this. Doing so can break the slot or ruin
the PC card.
4. Select a file or a slide.
NOTE: The Mouse pad (+) or (–) button is valid only when the Menu
Use the Mouse pad (+) or (–) button on the remote control to select
the file or slide you want to display and press the Enter button on
the cabinet or the Left Click button on the remote control. See the
following pages for more details.
button is lit.
Multi Cursor
Table Cursor
File
File
File
File
2
1
3
4
presentation
presentation
presentation
A
presentation
B
C
D
File
File
File
6
5
7
presentation
presentation
presentation
E
presentation
F
G
H
* The selected file or slide will be displayed.
NOTE: If you select "Start" and press the Enter button on the cabinet
or the Left Click button on the remote control, the slides will be looped.
To use the Start feature, you must first set on the software included
with the MT Viewer board.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
38
75
3.Use the Mouse pad (+) or (–) button on the remote control to move
the Multi-Cursor (blue box) to the file you want to display a slide
from, and press the Enter button on the cabinet or the Left Click
button on the remote control.
Selecting a File from a List of Files
*
The Viewer feature allows you to store one or more presentation materials in a
single flash memory card. Each material is referred to as a "file" or "slide".
To select a file from a list of files
1.Press the Menu button on the remote control or cabinet to select "PC
Card".
File
File
File
File
2
1
3
4
Multi Cursor
File
File
File
File
6
5
7
8
2. Use the Mouse pad (+) or (-) button on the remote control to select
"Select File" and press the "Enter" button on the cabinet or the Left
Click button on the remote control.
* This will display the first slide of the selected file.
3.Use the Mouse pad (+) or (–) button on the remote control to move
the Table-Cursor (yellow box) to the slide you want to display and
press the Enter button on the cabinet or the Left Click button on the
NOTE: A maximum of 16 indexes can be switched with "Select File".
The last displayed file, which is always exclusively for use of Capture,
will be displayed during capturing only.
When 17 or more indexes exist n the flash memory card and you wish
to display them, move the index to be displayed to the beginning of
the file indexes with "Editing file indexes" under "Files" of the software
for Viewer.
remote control.
Table Cursor
presentation
presentation
presentation
presentation
B
A
C
D
presentation
presentation
presentation
presentation
F
E
G
H
Selecting a Slide from a List of Slides (Table)
To select a slide from a list of slides
1.Press the Menu button on the remote control or cabinet to select
"PC Card".
* This will display the selected slide.
2. Use the Mouse pad (+) or (-) button on the remote control to select
"Select Slide" and press the "Enter" button on the cabinet or the Left
Click button on the remote control.
NOTE: The Slide (+) and (-) button on the remote control can be
also used to select a file or slide, or to turn pages.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
39
77
Switching Slides
Capturing the currently displayed screen image
The Viewer feature allows you to capture a screen image and store
it to a flash memory card.
To capture a screen image and store it to a flash memory card;
Select "Capture" from the Settings menu and press the Enter button
on the cabinet or Left Click button on the remote control.
* To view the captured image
To switch slides, press "SLIDE +" or "SLIDE -" button. This will cancel
the Auto Play mode. To set the Auto Play mode, press the Menu button
to select “Start” from the Source menu and press the Enter button on the
cabinet or the Left Click button on the remote control. This is valid only
when theAuto Play mode is selected. See more information about “Auto
Play mode” for the Help file included with the Viewer board.
* SLIDE- returns to the previous slide.
SLIDE+ advances to the next slide.
NOTE: Editing tasks such as deleting the data inside the flash memory
card cannot be accomplished with the LCD projector. Use the
exclusive software on your PC for this purpose. If you accidentally
delete data required for playback, playing back the data is not
possible.
1.Select "Select File" from the Source menu and display a list of
files.
* A thumbnail (reduced image) of the first captured image will be
displayed.
Effect Sound
The Viewer function allows you to play back effect sound for the slide.
Playing back effect sound can be accomplished during the switching
slides or files only. To use this feature, you must first specify the effect
sound with the supplied software.
You can adjust volume by using the Volume button.
2.Use the Mouse pad (+) button to move the Multi-Cursor (blue box) to
the last file and press the Enter button on the cabinet or the Left Click
button on the remote control.
Projecting Pictures a Digital CameraTook
Playing back on the LCD projector is possible if a picture meets one
of the following requirements:
* A picture that can be stored to an MS-DOS-formatted ATA flash
memory card
* A picture that can be stored as a compatible format
File
File
File
File
2
1
3
4
Multi Cursor
File
File
File
File
The on-board Viewer searches for the directory on the card to
recognize a JPEG or BMP format image as slide. Directories to be
searched for are up to two level from the root directory and must be
less than 16 directories. Although only switching folders and slides
is possible, special effects and displaying a list is not possible.
6
5
7
8
NOTE:
* This will display the image you captured first.
* Up to 128 images can be recognized as slides for one directory.
* To use special effects, read images from a flash memory card and
edit them using the supplied software, then store them to another
flash memory card.
* If you store indexes to the flash memory card for your digital
camera using the supplied software, images taken with the digital
camera cannot be viewed on the Viewer. So preparing flash
memory cards for a digital camera and Viewer respectively is
recommended.
NOTE: The menu indicating that capturing is now performing will
be displayed during capturing. During this time do not remove the
flash memory card nor turn off the power of the LCD projector. Doing
so may destroy the data of the flash memory card.
* When the flash memory card becomes full, replace a new one.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
40
4
M A I N T E N A N C E
79
This section describes the simple maintenance procedures you should follow
to replace the lamp, clean or replace the filter, and replace the batteries in the
remote control.
Replacing The Lamp
Step 1A
Step 1B
After your lamp has been operating for 2000 hours or longer, the
“status” light in the cabinet will go on. Even though the lamp may still
be working, replace it at 2000 hours to maintain optimal projector
performance.
CAUTION
• DO NOT TOUCH THE LAMP immediately after it has been used. It will
be extremely hot. Allow at least one hour for the lamp to cool before
handling.
• DO NOT REMOVE ANY SCREWS except the lamp cover set screw
and two lamp case screws. You could receive an electric shock.
• Turn off the main power to the projector and disconnect the power cord.
Allow at least one hour for the lamp to cool.
• The projector will turn off and go into stand by mode after 2100 hours of
service. If this happens, be sure to replace the lamp. If you continue to
use the lamp after 2000 hours of use, the lamp bulb may shatter, and
pieces of glass may be scattered in the lamp case. Do not touch them as
the pieces of glass may cause injury. If this happens, contact your NEC
dealer for lamp replacement.
Step 2
To replace the lamp:
1. Loosen the single screw that secures the lamp housing cover and remove
the cover.
2. Loosen the two screws securing the lamp case.
3. Remove the lamp by pulling out the complete assembly.
4. Install a new lamp case assembly and secure it in place with the two screws.
Step 3
Step 4
CAUTION: Do not use a lamp other than the NEC replacement lamp.
Order this from your NEC dealer using your projector's model number.
5. Reattach the lamp cover and tighten the single screw.
6. After you install a new lamp, select the lamp Usage icon and press and hold
the "Power On" button on the remote control for ten seconds to reset the
lamp time clock to zero.
NOTE: If resetting the lamp clock back to zero after 2100 hours of service,
press the "Power Off" (not "Power On") button on the remote control for ten
seconds .
NOTE: When you replace the lamp, it is also wise to replace the filter. The
filter comes in the same package with your replacement lamp.
Step 5
MAINTENANCE
80
Download from Www.Somanuals.com. All Manuals Search And Download.
41
81
Cleaning Or Replacing The Filter
The air-filter sponge keeps the inside of the MultiSync MT830/1030 LCD Projector free from dust or
dirt and should be cleaned after every 100 hours of operation (more often in dusty conditions). If the
filter is dirty or clogged, your projector may overheat.
NOTE: Clean your filter after every 100 hours of operation.
CAUTION
• Turn off the main power and unplug the projector before replacing the filter.
• Only clean the outside of the filter cover with a vacuum cleaner.
• Do not attempt to operate the projector without a filter cover.
• Your LCD projector will not operate unless the filter cover is installed correctly.
To clean the air-filter:
Vacuum the filter through the filter cover.
To replace the air-filter:
1. Remove the filter cover by pushing up on the catch of the cover with a flat-head screwdriver until
you feel it detach.
2. Reinstall the new filter cover.
NOTE: Do not detach the sponge from the filter cover. Do not wash the filter cover with soap and
water. Soap and water will damage the filter membrane.
Before replacing the filter cover, remove dust and dirt from the projector cabinet. Keep out
dust and dirt during filter replacement.
Remote Control Battery Installation
1. Press firmly and slide the battery cover off.
2. Remove both old batteries and install new ones (AA). Ensure that you have the batteries' polarity
(+/–) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place.
MAINTENANCE
82
Download from Www.Somanuals.com. All Manuals Search And Download.
42
83
Cette section décrit les procédures simples d’entretien que vous aurez à suivre pour
remplacer la lampe, nettoyer ou remplacer le filtre et remplacer les piles de la télécommande.
Remplacement de la lampe
Lorsque la lampe a été utilisée pendant 2000 heures ou plus, le voyant “Status” (état) du
coffret s’allume. Même si la lampe peut encore fonctionner, remplacez-la au bout de
2000 heures pour conserver une performance optimale de votre projecteur.
Etape 1A
Etape 1B
PRECAUTIO N
•
NE TOUCHEZ PASALA LAMPE juste après qu’elle a été utilisée. Elle est très
chaude. Laissez-la refoidir pendant au moins une heure avant de la manipuler.
• NE RETIREZAUCUNE VIS mis à part la vis qui fixe le couvercle de lampe
et les deux vis du compartiment de lampe. Vous risquez de recevoir une
décharge éléctrique.
• Mettez le projecteur hors circuit et débranchez le cordon d’alimentation.
Laissez refroidir la lampe pendant au moins une heure.
• Le projecteur s’éteindra et restera en attente après 2100 heures d’utilisation.
Dans ce cas, remplacez la lampe. Si vous continuez d’utiliser la lampe après
2000 heures d’utilisation, l’ampoule peut se briser et des brisures de verre
peuvent être éparpillées dans le compartiment de la lampe. Ne les touchez pas
car elles peuvent vous blesser. Dans ce cas, contactez votre revendeur NEC
afin de procéder au remplacement de la lampe.
Etape 2
Pour remplacer la lampe :
1. Desserrer l’unique vis qui fixe le couvercle de lampe et retirez le couvercle.
2. Desserrer les deux vis qui fixent le compartiment de lampe.
3. Retirez la lampe en tirant tout l’assemblage.
Etape 3
Etape 4
4. Installez un nouvel assemblage de compartiment lampe et fixez-le avec les deux vis.
PRECAUTION: N’utilisez pas d’autres lampes qu’une lampe de
rechange NEC.
Commandez-la auprès de votre vendeur NEC en donnant le numéro
de modèle du projecteur.
5. Fixez de nouveau le couvercle de lampe et serrer la vis unique.
6. Une fois la nouvelle lampe installée, sélectionnez l’icone d’utilisation de lampe
et appuyez et maintenez la touche “Power On” (alimentation activée) de la
télécommande pendant dix secondes afin de remettre à zéro l’horloge de lampe.
REMARQUE: Pour remettre à zéro l’horloge de lampe après 2100 heures
d’utilisation, appuyez sur la touche “Power Off” (alimentation désactivée)(et
non “Power On” (alimentation activée)) de la télécommande pendant dix
secondes .
REMARQUE: Lorsque vous remplacez la lampe, il est recommandé de
changer également le filtre. Le filtre se trouve dans le même emballage que
la lampe de rechange.
Etape 5
MAINTENANCE
84
Download from Www.Somanuals.com. All Manuals Search And Download.
43
85
Nettoyage ou remplacement du filtre
Le coussin éponge du filtre à air maintient l’intérieur du projecteur à affichage à cristaux liquides
MultiSync MT830/1030 à l’abri de la poussière ou de la saleté et doit être nettoyé toutes les 100 heures
d’utilisation (plus souvent dans les endroits poussiéreux). Si le filtre est sale ou bouché, le projecteur
risque de surchauffer.
REMARQUE: Nettoyez le filtre toutes les 100 heures d’utilisation.
PRECAUTION
• Couez l’alimentation et déranchez le projecteur avant de remplacer le filtre.
• Nettoyez uniquement le couvercle extérieur du filtre avec un aspirateur.
• N’essayez pas de faire fonctionner le projecteur sans couvercle de filtre.
• Votre projecteur à affichage à cristaux liquides ne fonctionnera pas tant que le couvercle de filtre ne
sera pas installé correctement.
Pour nettoyer le filtre à air:
Aspirez le filtre à travers le couvercle de filtre.
Pour remplacer le couvercle de filtre:
1.Retirez le couvercle de filtre en poussant vers le haut sur le cliquet du couvercle à l’aide d’un tournevis
à tête plate jusqu’à ce que vous sentiez qu’il se détache.
2.Réinstallez le nouvel couvercle de filtre.
NOTE: Ne détachez pas le coussin éponge du couvercle de filtre. Ne lavez pas le filtre au savon et à
l’eau. Le savon et l’eau endommageront la membrane du filtre.
Avant de remplacer le filtre à air, dépoussiérez et nettoyez le coffret du projecteur. Maintenez propre
pendant le remplacement du filtre.
Installation des piles de la télécommande
1. Appuyez fermement et retirez le couvercle des piles en le faisant glisser.
2. Retirez les deux piles usagées et installez de nouvelles piles (AA). Assurez-vous de respecter la
polarité (+/–) des piles.
3. Remettez le couvercle des piles en le faisant glisser, jusqu’à ce qu’il s’emboîte.
MAINTENANCE
86
Download from Www.Somanuals.com. All Manuals Search And Download.
44
5 T R O U B L E S H O O T I N G
87
This section helps you resolve problems you may encounter while setting up or using your MultiSync MT830/1030 LCD Projector.
Status Light Messages
Condition
Status
OFF
Ⅵ Normal
On continually
Ⅵ The projector lamp has exceeded 2000 hours of operation and
should be replaced.
Blinking very rapidly
Ⅵ Either the lamp cover or filter cover is not fastened properly. Check
(On and off in a cycle of 1 sec.)
each and reattach them if necessary.
Blinking slowly
Ⅵ The cooling fan has stopped. Contact your NEC dealer for service.
(On and off in a cycle of 8 sec.)
Blinking very slowly
Ⅵ The lamp is not turned on.
(On and off in a cycle of 12 sec.)
• The projector was turned off and back on too quickly. Turn
off the projector, wait one minute, then turn the projector
back on. Or the lamp is burnt out.
TROUBLE SHOOTING
88
Download from Www.Somanuals.com. All Manuals Search And Download.
45
89
Common Problems & Solutions
Problem
Check These Items
Does not turn on
• Check that the cord is plugged in and that the power switch on the front panel is on.
• Ensure that the filter cover is installed correctly. (See page 82.)
• Check to see if the projector has overheated or the lamp usage exceeds 2100 hours. If there is insufficient ventilation around the
projector or if the room where you're presenting is particularly warm, move the projector to a cooler location.
Check the filter and clean it if necessary.
No picture
• Use the menu icons to select your source (Video, S-Video, RGB1, 2 or PC Card). (See pages 61 and 62.)
• Ensure your cables are connected properly.
• Use icons to adjust the brightness and contrast.
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the RESET icon on the Settings Menu.
Image isn’t square to the screen
• Reposition the projector to improve its angle to the screen.
• Use the keystone icon or the keystone button to correct the keystone distortion.
Picture is blurred
• Adjust the focus. (See page 20 or 29.)
• Reposition the projector to improve its angle to the screen.
• Ensure that the distance between the projector and screen is within the adjustment range of the lens.
Image is scrolling vertically,
horizontally or both
• Use icons to select the source you want to input.
• Make sure the recalled Custom Memory supports the current input signal.
Remote control does not work
• Install new batteries. (See page 82 or 86.)
• Make sure there are no obstacles between you and the projector.
• Stand within 23 feet (7m) of the projector.
Problem
Check These Items
Status indicator is lit or
blinking
See the Status Light message chart on pages 87 and 88.
Cross color in RGB mode
If “Auto Picture” is off, turn it on. If “Auto Picture” is on, turn it off and balance the image with the Picture Adjustment icon and
Fine Picture Adjustment icon.
When using the Viewer function
Problem
Check These Items
No picture
• Is the viewer board been seated in the LCD projector completely?
• Is "PC CARD" selected from the Source menu?
• Is the flash memory card seated in the card slot completely?
• Are slide data being transferred to the flash memory card?
• Have the contents of the flash memory card been destroyed?
Part of a slide is not
displayed
• While an image with over 1024
ן 768 dots is projected, several lines of information will be lost. Use the supplied software to change the image to 1024
ן 768 dots in size. No effect sound
• Is the sound volume set to the minimum level?
To Contact Your NEC Service Representative, Call 1-800-836-0655
TROUBLE SHOOTING
90
Download from Www.Somanuals.com. All Manuals Search And Download.
46
6 S P E C I F I C A T I O N S
91
This section provides technical information about the MultiSync MT830/1030 LCD Projector's performance.
Optical
LCD Panel
1.3", p-Si TFT active-matrix, 800
ן 600 dot (MT830) / 1024ן 768 dot (MT1030) Lens
Power zoom, power focus
F 2.5 f =52 – 68 mm
Lamp
New short arc high pressure lamp 150 W
(Guaranteed life span: 2,000 hours or
6 months from date of purchase,
whichever comes first.)
Image Size
20-300 inches diagonal
Projection Distance
Light Output
3.28 – 40.03 ft (1.0 – 12.2 m)
1000 ANSI lumens (MT830) / 900 ANSI lumens (MT1030)
300 : 1
Contrast Ratio
Color Temperature
9,000 ± 1500 Kelvin
Electrical
Inputs
Video (NTSC / PAL / SECAM / NTSC4.43)
RGB (H : 15 – 85 kHz, V : 50 – 85 Hz)
RGB: 80 MHz
Video Bandwidth
Color Reproduction
Full color, 16.7 million colors simultaneously.
Horizontal Resolution
550 TV lines at S-Video :
350 TV lines :
NTSC,
PAL / SECAM / NTSC 4.43
RGB
800 dots horizontal, 600 dots vertical (MT830)
1024 dots horizontal, 768 dots vertical (MT1030)
Power Requirement
Input Current
100 – 120 / 220 – 240 VAC, 50 / 60 Hz
3.5 A / 1.5A
Mechanical
Dimensions
13.2" (W)
ן 5.8" (H)ן 15.6" (D) 33.5 cm (W)
ן 14.8 cm (H)ן 39.6 cm (D) Net Weight
16.1 lbs / 7.3 kg
Operational Temperatures
LCD projector: 32° – 104°F(0°to 40°C), 20 – 80% humidity
Remote control: 32° – 140°F (0° to 60°C)
Remote mouse receiver: 32° – 140°F (0° to 60°C)
Regulations
ULApproved (UL 1950, CSA 950)
Meets DOC Canada requirements
Meets FCC Class A requirements
SPECIFICATIONS
92
Download from Www.Somanuals.com. All Manuals Search And Download.
47
93
Cabinet Dimensions
11.4"
(290)
F O C U S Z O O M
–
O N / O F F
–
+
P O W E R
S T A T U S
+
E N T E R
+
–
S E L E C T
M E N U
7"
(178.5)
13.1"
(332)
AC IN
Unit : inch (mm)
SPECIFICATIONS
94
Download from Www.Somanuals.com. All Manuals Search And Download.
48
95
D-Sub Pin Assignments
PC 15-Pin mini D-Sub
PC 15-Pin mini D-Sub
Pin No. Signal to be connected
1
Red
2
4
3
1
5
2
Green
9
6
10
8
7
15 14 13 12
11
3
Blue
4
GND
5
GND
6
Red GND
Green GND
Blue GND
No Connection
Digital GND
GND
7
8
9
10
11
12
13
14
15
No Connection
Horizontal Sync
Vertical Sync
No Connection
SPECIFICATIONS
96
Download from Www.Somanuals.com. All Manuals Search And Download.
49
97
Timing Chart
Y/N
Signal
Resolution
Refresh
F.H.
Dot
Rate (Hz)
(kHz)
Clk(MHz)
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
NTSC
PAL
SECAM
VESA
IBM
VESA
MAC
VESA
IBM
MAC
MAC
MAC
VESA
VESA
IBM
640
ן 480 768
ן 576 768
ן 576 640
ן 350 640
ן 400 640
ן 400 640
ן 400 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 720
ן 350 720
ן 400 720
ן 400 720
ן 350 60
50
50
85.08
70
85.08
66
59.94
60
15.734
15.625
15.625
37.86
31.47
37.86
35
31.47
31.47
31.47
34.97
35
-
-
-
31.5
25.175
31.5
30.24
25.175
25.175
25.175
31.334
30.24
31.5
31.5
31.49
36
60
66.7
66.67
72.81
75
37.86
37.5
75
39.375
43.269
31.469
31.4469
37.927
39.44
VESA
IBM
IBM
VESA
IBM
85.01
70.09
70.09
85.04
87.85
28.322
28.322
40
35.5
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
#
#
#
#
#
#
#
#
#
IBM
720
ן 400 800
ן 600 800
ן 600 800
ן 600 800
ן 600 800
ן 600 832
ן 624 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1152
ן 870 1152
ן 900 1152
ן 900 1280
ן 1024 1280
ן 1024 1280
ן 1024 1280
ן 1024 1280
ן 1024 1280
ן 1024 87.7
39.375
35.16
37.879
48.077
46.88
53.674
49.725
35.5
48.363
57.476
58.131
60.241
60.023
68.677
49.7
35.5
36
40
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
IBM
MAC
VESA
VESA
SGI
MAC
SUN
56.25
60.32
72.19
75
85.06
74.55
43interlace
60
70.07
72.03
74.93
75.03
85
50
49.5
56.25
57.283
44.9
65
75
79
80
1024
ן 768 and 832ן 624 images are compressed into 800
ן 600 on MT830 78.75
94.5
70
60.4
75.6
68.7
100
92.94
105.6
107.35
108
118.5
135
135
135
69.95
76.05
60
60.04
69.89
72.01
75.03
76.11
61.769
71.736
63.9
64.286
74.882
78.125
79.976
81.13
SGI
SGI
# 1152
ן 870, # 1152ן 900 and # 1280ן 1024 images are compressed into 1024
ן 768 on MT1030 with AccuBlend ; 800
ן 600 on MT830 with AccuBlend
VESA
MAC
HP
VESA
SUN
SPECIFICATIONS
98
Download from Www.Somanuals.com. All Manuals Search And Download.
50
99
PC Control Command Reference
Command Codes
No.
01
02
03
04
05
06
07
08
09
10
11
12
13
Function
Code
03H
04H
05H
C6H
27H
08H
14H
47H
11H
09H
0AH
0BH
0CH
Data
No
No
No
No
No
No
No
No
No
No
No
No
No
Description
Same as remote
Same as remote
Same as remote
Video
RGB1
RGB2
S-VIDEO
PC CARD
Power On
Power Off
Picture Mute
Onscreen Mute
Power Zoom W
Power Zoom T
Power Focus +
Power Focus –
Same as remote
Same as remote (available only when the Viewer board is installed)
Same as remote (See NOTE on page 104.)
Same as remote
Same as remote
Same as remote
Same as remote
Same as remote
Same as remote
14
15
16
Reset
43H
4CH
4BH
No
No
No
(Resets immediately after returning ACK)
Same as remote
Freeze
Slide +
Same as remote (available only whenPC CARD is selected)
17
18
19
20
21
22
23
24
25
26
Slide -
20H
33H
34H
35H
36H
19H
1AH
No
No
No
No
No
No
No
Yes
No
No
Same as remote (available only whenPC CARD is selected)
Front Floor
Front Ceiling
Rear Floor
Rear Ceiling
Auto Start On
Auto Start Off
Image mode Select 1EH
Power Management On 15H
Power Management Off 16H
0 to 2 at Video, 3 to 5 at the others
SPECIFICATIONS
100
Download from Www.Somanuals.com. All Manuals Search And Download.
51
101
Command Codes (continued)
No.
27
28
29
30
31
32
33
34
35
36
37
38
Function
Brightness
Contrast
Code
60H
62H
64H
66H
68H
6AH
70H
6EH
72H
74H
3FH
3DH
Data
Yes
Yes
Yes
Yes
Yes
Yes
Yes*
Yes
Yes
Yes
No
Description
0 to 63
0 to 63
Color
0 to 63
Tint
-32 to +31(E0 to 1F)
0 to 3
Sharpness
Audio Volume
Picture Adj
Fine Picture
H Position
V Position
Lamp Reset
Language Select
0 to 63
768 to 1279 (2 byte code)
0 to 31
-64 to +63 (C0 to 3F)
-32 to +31 (E0 to 1F)
Yes
00:English, 01:German, 02:French, 03:Italian, 04:Spanish, 05:Swedish
39
White Balance
Sub Brightness
R
G
B
R
G
B
75
76
77
78
79
7A
7F
61
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 to 7FH
0 to 7FH
0 to 7FH
Sub Contrast
0 to 7FH
0 to 7FH
0 to 7FH
40
41
Pointer Select
Video System
0 to 7
0 to 2 (available only when VIDEO is selected)
These commands are subject to change without notice.
*(Low-order data) (High-order data) CSUM
CSUM = Checksum is a low-order digit of the sum from the Code to the immediately preceding data.
SPECIFICATIONS
102
Download from Www.Somanuals.com. All Manuals Search And Download.
52
103
Cable Connection
Communication Protocol
Baud rate:
Data length:
Parity:
9600 bps
8 bits
No parity
One bit
None
Stop bit:
X on/off:
Full duplex
Communications
procedure:
If the CPU of the LCD projector has received the data correctly, it returns an ACK(C5H). If the received data is not correct, the CPU returns a
NAK(CAH), then the following status:
Receiving success:
Receiving failure:
Err 01:
C5
CA Err
Command Error (command not supported)
Checksum Error
Err 02:
Err 03:
Busy (command not acceptable)
Err 04:
Parameter Error ( parameter data abnormal)
PC Control Connector (DIN-8P)
To RxD of PC
ᮣ
NOTE: If failing in powering-on, the CPU returns the following NAKs:
44
8
6
7
CA Err 1
Err 1 8X (Apply the corresponding bit.)
Bit 0: Either filter panel or lamp cover is not attached correctly
Bit 1: Fan stoppage
5
4
3
2
1
Bit 2: Overheated
Bit 3: Lamp lighting failure
To GND of PC
To TxD of PC
ᮣ
ᮤ
SPECIFICATIONS
104
Download from Www.Somanuals.com. All Manuals Search And Download.
53
|