NEC Projector GT5000 User Manual
GT5000  
LCD Projector  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Information  
Precautions  
RF Interference  
Please read this manual carefully before using your NEC GT5000  
Projector and keep the manual handy for future reference.  
Your serial number is located on the bottom of your GT5000.  
Record it here:  
WARNING  
The Federal Communications Commission does not allow any  
modifications or changes to the unit EXCEPT those specified by  
NEC Solutions, Inc. in this manual. Failure to comply with this  
government regulation could void your right to operate this equip-  
ment.  
CAUTION  
To turn off main power, be sure to remove the plug  
from power outlet.  
The power outlet socket should be installed as near  
to the equipment as possible, and should be easily  
accessible.  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to Part 15 of the FCC  
Rules. These limits are designed to provide reasonable protec-  
tion against harmful interference in a residential installation.This  
equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the in-  
structions, may cause harmful interference to radio communica-  
tions. However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can  
be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of  
the following measures:  
CAUTION  
TO PREVENT SHOCK, DO NOT OPENTHE CABI-  
NET.  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED NEC SER-  
VICE PERSONNEL.  
This symbol warns the user that uninsulated volt-  
age within the unit may be sufficient to cause elec-  
trical shock.Therefore, it is dangerous to make any  
kind of contact with any part inside of the unit.  
•
•
•
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
•
Consult the dealer or an experienced radio / TV technician for help.  
This symbol alerts the user that important informa-  
tion concerning the operation and maintenance of  
this unit has been provided.The information should  
be read carefully to avoid problems.  
Important Safeguards  
These safety instructions are to ensure the long life of your projector  
and to prevent fire and shock. Please read them carefully and heed  
all warnings.  
WARNING  
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT Installation  
TO RAIN OR MOISTURE.  
1. For best results, use your projector in a darkened room.  
DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EX-  
TENSION CORD OR IN AN OUTLET UNLESS ALL THREE  
PRONGS CAN BE FULLY INSERTED.  
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE  
COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY  
QUALIFIED NEC SERVICE PERSONNEL.  
2. Place the projector on a flat, level surface in a dry area away from  
dust and moisture. To avoid premature lamp failure, do not tilt the  
front of the projector up or down by more than 45° from level.  
3. Do not place your projector in direct sunlight, near heaters or heat  
radiating appliances.  
4. Exposure to direct sunlight, smoke or steam can harm internal  
components.  
DOC Compliance Notice  
5. Handle your projector carefully. Do not hold the lens hood and the  
terminal covers. Dropping or jarring can damage internal compo-  
nents.  
This Class B digital apparatus meets all requirements of the Ca-  
nadian Interference-Causing Equipment Regulations.  
6. Do not place heavy objects on top of the projector.  
7. If you wish to have the projector installed on the ceiling:  
a. Do not attempt to install the projector yourself.  
3. GSGV Acoustic Noise Information Ordinance:  
The sound pressure level is less than 70 dB (A) according to ISO  
3744 or ISO 7779.  
b. The projector must be installed by qualified technicians in or-  
der to ensure proper operation and reduce the risk of bodily  
injury.  
In UK, a BS approved power cable with moulded plug has a Black  
(five Amps) fuse installed for use with this equipment. If a power  
cable is not supplied with this equipment please contact your  
supplier.  
c. In addition, the ceiling must be strong enough to support the  
projector and the installation must be in accordance with any  
local building codes.  
•
•
•
IBM is a registered trademark of International Business Machines Cor-  
poration.  
d. Please consult your dealer for more information.  
Macintosh and PowerBook are registered trademarks of Apple Com-  
puter, Inc.  
To Dealer or Installer:  
Other product and company names mentioned in this user's manual  
may be the trademarks of their respective holders.  
To prevent the projector from falling, install it in a place and fasten it in  
a way with sufficient strength to support the combined weight (24.0  
kg/53.0 lbs) of the projector (18.4 kg/40.6 lbs), the lens (2.0 kg/4.4  
lbs) and the ceiling mount(3.2 kg/7.1 lbs) for an extended period of  
time as well as to withstand earthquakes.  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Information  
•
The projector must be operated with two lamp housings installed  
regardless of whether or not the lamp is active. Failure to do so  
may degrade the performance of the projector such as screen flicker  
or loss of lamp life. If one lamp has reached the end of its usable  
life, replace it with a new one as soon as possible.  
Power Supply  
1. The projector is designed to operate on a power supply of 100-  
120 or 200-240 V 50/60 Hz AC. Ensure that your power supply fits  
this requirement before attempting to use your projector.  
2. Handle the power cable carefully and avoid excessive bending. A  
damaged cord can cause electric shock or fire.  
3. If the projector is not to be used for an extended period of time,  
disconnect the plug from the power outlet.  
4. Do not touch the power plug with wet hand. Doing so can cause  
electrical shock or fire.  
Fire and Shock Precautions  
1. Ensure that there is sufficient ventilation and that vents are unob-  
structed to prevent the build-up of heat inside your projector. Allow  
at least 3 inches (10 cm) of space between your projector and a  
wall. Allow at least 12 inches (30cm) of space between the outlets  
on the left side (when viewed from the front) and the wall.  
5. Do not touch the power plug during a thunder storm. Doing so  
can cause electrical shock or fire.  
2. Prevent foreign objects such as paper clips and bits of paper from  
falling into your projector. Do not attempt to retrieve any objects  
that might fall into your projector. Do not insert any metal objects  
such as a wire or screwdriver into your projector.If something should  
fall into your projector, disconnect it immediately and have the ob-  
ject removed by a qualified NEC service personnel.  
Cleaning  
1. Unplug the projector before cleaning.  
2. Clean the cabinet periodically with a damp cloth. If heavily soiled,  
use a mild detergent.Never use strong detergents or solvents such  
as alcohol or thinner.  
3. Do not place any liquids on top of your projector.  
4. When using a LAN cable:  
3. Use a blower or lens paper to clean the lens, and be careful not to  
scratch or mar the lens.  
For safety, do not connect to the connector for peripheral device  
wiring that might have excessive Voltage.  
CAUTION  
Do not unplug the power cable from the wall outlet under any one of  
the following circumstances. Doing so can cause damage to the pro-  
jector:  
CAUTION  
•
Do not look into the lens while the projector is on. Serious damage  
to your eyes could result.  
•
•
•
While the message "Please wait a moment." appears. This mes-  
sage will be displayed after the projector is turned off.  
•
Keep any items such as magnifying glass out of the light path of  
the projector. The light being projected from the lens is extensive,  
therefore any kind of abnormal objects that can redirect light com-  
ing out of the lens, can cause unpredictable outcome such as fire  
or injury to the eyes.  
Immediately after the power cable is plugged into the wall outlet  
(the POWER indicator has not changed to a steady orange glow).  
Immediately after the cooling fan stops working (The cooling fan  
continues to work for 90 seconds after the projector is turned off  
with the POWER button).  
•
Do not cover the lens with the supplied lens hood cap or equiva-  
lent while the projector is on. Doing so can lead to melting of the  
cap and possibly burning your hands due to the heat emitted from  
the light output.  
CAUTION  
•
Do not try to touch the ventilation outlets as they can become heated  
while the projector is turned on.  
•
Do not put the projector on its side when the lamp is turned on.  
Doing so may cause damage to the projector.  
•
•
Before shipping this projector, remove the lens and attach the lens  
hood cap.  
The Lens Shift mechanism may encounter damage caused by im-  
proper handling during transportation.  
Do not eject a PC card or LAN card while its data is being ac-  
cessed. Doing so can damage your PC card or LAN card data.  
Lamp Replacement  
•
•
To replace the lamp, follow all instructions provided on page 9-2.  
Be sure to replace the lamp when the message "The Lamp has  
reached the end of its usable life. Please replace the lamp." ap-  
pears. If you continue to use the lamp after the lamp has reached  
the end of its usable life, the lamp bulb may shatter, and pieces of  
glass may be scattered in the lamp case.Do not touch them as the  
pieces of glass may cause injury. If this happens, contact your NEC  
dealer for lamp replacement.  
•
Allow a minimum of 90 seconds to elapse after turning off the pro-  
jector.Then turn off the main power and disconnect the power cable  
and allow 60 minutes to cool the projector before replacing the  
lamp.  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
1. Introduction  
7. Setting Up for Double Stacking in Link Mode  
z Stacking and Connecting the Projectors ............................... 7-2  
x Adjusting and Registering Signals to Be Projected .............. 7-5  
c Adjusting the Lens Shift, Zoom and Focus to Clearly Display  
all projected patterns .............................................................. 7-5  
v Link Mode Setting .................................................................... 7-5  
b List of Menu Items Available in Link Mode ............................ 7-6  
z What's in the Box? .................................................................... 1-2  
x Introduction to the Projector ................................................... 1-3  
c Getting to KnowYour Projector ............................................... 1-4  
Attaching the lens hood cap to the lens hood with the supplied  
string and rivet ............................................................................ 1-6  
Carrying the Projector ................................................................. 1-6  
Top Features ............................................................................... 1-7  
Ter minal Panel Features ............................................................. 1-8  
v Remote Control Features....................................................... 1-10  
Remote Control Precautions..................................................... 1-12  
Remote Control Battery Installation .......................................... 1-12  
Operating Range for Wireless Remote Control ........................ 1-12  
Using the Remote Control in Wired Operation ......................... 1-13  
8. Using On-Screen Menu  
z Basic Menu Operation.............................................................. 8-2  
x List of Direct Button Combinations ........................................ 8-3  
c Menu tree................................................................................... 8-4  
v Menu Descriptions & Functions.............................................. 8-7  
Adjust (Source) ........................................................................... 8-8  
Picture ................................................................................. 8-8  
Video Adjust ........................................................................ 8-8  
Picture Management ........................................................... 8-9  
Image Options ................................................................... 8-10  
Option Adjust ..................................................................... 8-10  
Lens Memory..................................................................... 8-11  
Signal Type ........................................................................ 8-11  
Sound ....................................................................................... 8-11  
Ref. Adjust ................................................................................ 8-12  
Using 3D Reform ............................................................... 8-12  
Screen Type ....................................................................... 8-12  
Reference White Balance .................................................. 8-12  
Reference Color Correction ............................................... 8-12  
Reference Lens Memory ................................................... 8-13  
Factory Default ......................................................................... 8-13  
Projector Options ...................................................................... 8-13  
Menu ................................................................................. 8-13  
Setup ................................................................................. 8-15  
Lamp Settings ................................................................... 8-18  
Link Mode .......................................................................... 8-18  
LAN Mode ......................................................................... 8-19  
Setting a Password ............................................................ 8-22  
Security ............................................................................. 8-23  
Tools ......................................................................................... 8-24  
Timer ................................................................................. 8-24  
Using Capture ................................................................... 8-26  
Using PC Card Files .......................................................... 8-26  
Using ChalkBoard ............................................................. 8-26  
Help .......................................................................................... 8-26  
Contents ............................................................................ 8-26  
Source Information ............................................................ 8-26  
Projector Information ......................................................... 8-27  
Test Pattern............................................................................... 8-27  
2. Installation  
z Setting UpYour Projector ........................................................ 2-2  
Screen Size and Projection Distance ......................................... 2-2  
x Lens Shift Adjustable Range ................................................... 2-4  
c Optional Lens Installation ....................................................... 2-6  
v Making Connections ................................................................ 2-8  
Connecting Your PC or Macintosh .............................................. 2-8  
To connect Scart Output ............................................................. 2-9  
Connecting an External Monitor ................................................. 2-9  
Connecting Your DVD Player .................................................... 2-10  
Connecting Your VCR or Laser Disc Player .............................. 2-11  
Connecting the Supplied Power Cable ..................................... 2-11  
3. Projecting an Image (Basic Operation)  
z Turning on the Projector .......................................................... 3-2  
x Selecting a Source ................................................................... 3-3  
c Adjusting the Picture Size and Position ................................. 3-3  
v Correcting the Horizontal and Vertical Keystone Distortion (3D  
Reform)..................................................................................... 3-4  
b Optimizing RGB Picture Automatically .................................. 3-6  
n Turning Up or Down Volume .................................................... 3-6  
m Turning off the Projector .......................................................... 3-7  
4. Convenient Features  
z Turning Off the Image and Sound ........................................... 4-2  
x Enlarging and Moving a Picture .............................................. 4-2  
c Getting the On-line Help and Information .............................. 4-2  
v Using a USB Mouse ................................................................. 4-3  
b Using a USB HUB Function ..................................................... 4-3  
n Changing Background Logo ................................................... 4-4  
m Making Freehand Drawings on  
, Projected Image (ChalkBoard) ................................................ 4-4  
. Lens Memory ............................................................................ 4-5  
9. Maintenancez Replacing the Lamp ......... 9-2  
z Replacing or Cleaning the Filter ............................................. 9-3  
x Cleaning the Cabinet and the Lens......................................... 9-4  
5. Using the Viewer  
z Making the Most out of the Viewer Function ......................... 5-2  
x Operating the Viewer Function from the Projector (playback) 5-  
10. Appendix  
3
z
USB Memory Device or USB Memory Card Reader Support ........ 10-2  
x Troubleshooting ...................................................................... 10-3  
c Specifications ......................................................................... 10-5  
v Cabinet Dimensions ............................................................... 10-7  
b Pin Assignments of D-Sub RGB Input Connector............... 10-7  
n Compatible Input Signal List ................................................. 10-8  
m REMOTE 1 Connector ............................................................ 10-9  
, PC Control Codes and Cable Connection .......................... 10-10  
Cable Connection ................................................................... 10-10  
PC Control Connector (D-SUB 9P)......................................... 10-10  
. Using Software Keyboard .................................................... 10-10  
⁄ Operation Using an HTTP Browser ..................................... 10-11  
6. Using the Projector in a Network  
z End User License Agreement ................................................. 6-2  
x Introduction............................................................................... 6-3  
c Supported Projectors ............................................................... 6-4  
v Equipment Connections and Settings.................................... 6-5  
b Software Installation ................................................................ 6-6  
n Starting/Exiting the Software .................................................. 6-7  
m Troubleshooting ........................................................................ 6-8  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
Introduction  
z What's in the Box? ....................................................1-2  
x Introduction to the Projector .....................................1-3  
c Getting to Know Your Projector .................................1-4  
Attaching the lens hood cap to the lens hood with the supplied string and rivet . 1-6  
Carrying the Projector ......................................................................................... 1-6  
Top Features........................................................................................................ 1-7  
Terminal Panel Features...................................................................................... 1-8  
v Remote Control Features .......................................1-10  
Remote Control Precautions ............................................................................. 1-12  
Remote Control Battery Installation................................................................... 1-12  
Operating Range for Wireless Remote Control ................................................. 1-12  
Using the Remote Control in Wired Operation .................................................. 1-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
z What's in the Box?  
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.  
Please save the original box and packing materials if you ever need to ship your Projector.  
NOTE: Lenses are optional. Order lenses from your NEC dealer.  
Terminal cover  
(Left and Right)  
F
O
C
U
S
P
C
Z
C
O
O
A
R
D
M
1
F
P
C
C
A
R
D
Z
2
D
L
O
E
F
L
W
A
T
M
N
P
1
L E N S S H I F T  
String (024C04541) and  
rivet (024C04531)  
L
A
M
P
2
U
P
R
I G  
H
T
S
R
E T N E  
T
A
T
U
S
C
A
P
N
O
W
C
S
E
E
E
R
L
L
E
C
T
O
N
S
/
M
E
T
A
N
U
N
D
B
3
Y
T
D
R
E
F
O
R
M
3
D
A
A
U
T
O
A
D
J U  
S
Projector  
Remote control (079646633) and  
batteries (AAA
ן
2)  
Lens hood cap  
(024F37661)  
Remote cable  
(073499391)  
Power cable for Europe (AC 230V)  
(07N080003)  
Power cable for North America (AC 120V)  
(07N080207)  
Power cable for Japan (AC 100V)  
(07N080107)  
Important  
Information  
User’s Manual  
(07N950192)  
User Supportware  
(07N950107)  
Documents  
(Japanese and English)  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
• Two timer settings - On/Off with programming or Sleep timer  
that counts down at selected intervals  
x Introduction to the Projector  
This chapter introduces you to the GT5000 high end fixed instal-  
lation projector and describes key features and controls.  
• 12V low voltage Screen Trigger output  
• Easy set up and operation  
Congratulations on Your Purchase of the GT5000 projec-  
tor  
• Eco-mode™ lamp technology for increased lamp life and en-  
ergy savings  
The GT5000 is our most sophisticated three panel, dual lamp  
XGA LCD projector. With the GT5000 you will be able to project  
images up to 500” (measured diagonally) from your DVD player,  
VCR, satellite hookup, HDTV source, PC, Workstation or  
• VORTEX Technology Plus™ for uncompromising display of  
video and data. Improves white level, color accuracy, dynamic  
range, and display of varying levels of black in an image  
Macintosh computer (desktop or notebook) and images from you • Wireless remote control operation  
digital camera PC Card or compact flash memory. The GT5000  
incorporates integrated networking access through the RJ45 in-  
• External control via RS232, USB or Network  
• NEC’s exclusive Advanced AccuBlend intelligent pixel blend-  
put or provides for wireless network connectivity from an optional  
wireless network PC card. With extensive input and output pan-  
els, optional long life lamp, full suite of quick-change lenses and  
a full function remote, the GT5000 will let you immerse yourself  
in large screen viewing.  
ing technology provides for extremely accurate image com-  
pression and HDTV (1920
ן
1080) display resolution*2.  
• Supports most IBMVGA, SVGA, XGA, Macintosh, component  
signal (YCbCr/YPbPr) or other RGB signals within a horizon-  
tal frequency range of 15 to 100 kHz and a vertical frequency  
range of 48 to 120 Hz. This includes NTSC, NTSC4.43, PAL,  
PAL-M, PAL-N, PAL60 and SECAM standard video signals  
Features you’ll enjoy on the GT5000:  
• Integrated RJ45 connector for wired networking ability  
• Two optional modular card slots allow for future projector growth  
with the ability to add additional input or output cards  
NOTE: Composite video standards are as follows:  
NTSC: U.S. TV standard for video in U.S. and Canada.  
NTSC4.43: TV standard used in Middle East countries.  
PAL: TV standard used in Western Europe.  
• Dual PC card slots provide for optional wireless/wired network  
connectivity or PC Card usage  
PAL-M: TV standard used in Brazil.  
• Email projector error status information to selected individuals  
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.  
PAL60: TV standard used for NTSC playback on PAL TVs.  
SECAM: TV standard used in France and Eastern Europe.  
• Power Horizontal and Vertical lens shift for optical display cor-  
rections  
• Lens memory controls lens attributes (zoom, focus, shift) de-  
pending on input resolution and input selected for fast and easy  
source transitions  
• NEC designed and developed SweetVisionTM technology for  
enhanced video image display, more vibrant colors and blacks  
richer with detail  
*1 The GT5000 meets ADA508 compliance, the latest American  
government regulation which provides for closed captioning,  
including a menu system that can be viewed by colorblind us-  
ers. This model also meets Executive Order 13221 require-  
ment for standby operation, which consumes less than 1 watt.  
*2 HDTV 1080P (1920
ן
1080), HDTV 1080i (1920
ן
1080) and  
HDTV 720 p (1280
ן
720) are displayed with NECs Advanced  
AccuBlend technology.  
• 3D Reform enhanced image technology for increased projec-  
tor versatility that provides for horizontal, vertical and diagonal  
keystone correction (allows for positioning the projector in off  
center locations in the room and still get aligned images)  
• Display 16:9 or 4:3 information and fill the screen  
• HDTV (1080p, 1080i, 720p) and SDTV (576p, 576i, 480p, 480i)  
compatibility  
• Intelligent lamp technology offers up to six user lamp settings  
to maximize light output or lamp life and provide for built in  
redundancy  
• Smart security settings for password protection, control panel  
lock, menu lock and PC card protection key to help prevent  
unauthorized access and adjustments to the projector  
• ADA508 and Executive Order 13221 Federal Government com-  
pliance *1  
• NEC 3D 10-bit video decoder for expanded black levels and  
adaptive gamma correction  
• High performance optional long life lamp for low total operat-  
ing costs  
• Digital photo viewer to display larger than life images from your  
digital cameras PC card or compact flash card  
• Double stackable for built in redundancy and high light output  
requirements  
• Built in 5W
ן
2 speakers for an integrated audio solution  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
c Getting to Know Your Projector  
Controls  
Terminal panel (Left)  
Y
B
R
D
E
N
W
A
T
O
P
/ S  
N
A U T O A D J U S T  
A
O
M
S
U
R
O
T
A
F
E
T
S
R
L
E
C
D
3
N
A
C
3 D  
2
P
M
A
L
R
E
T
N
1
P
E
M
S E L E C T  
A
L
2
U
D
N
R
E
A
M
C
C
P
1
R I G H T  
U P  
D
R
D O W N  
A
C
C
P
L E N S S H I F T  
L E F T  
Z
Z O O M  
F O C U S  
F
Lens hood  
Lamp cover 1 (Right)  
L/MO  
R
L/MONO  
S
Terminal panel (Right)  
L
A
O
U
T
D
1
R
G
B
2
I
O
R
R
/C  
r
R
G
B
O
U
T
G
/Y  
VIDEO  
S-VIDEO B/C  
b
H
/
HV  
L/MON
L/MON
R
Lens (optional)  
U
S
B
(
M
O
U
S
Built-in Security Slot ( )*  
Remote sensor  
E
/H  
U
B
)
U
S
B
(
1
P
C
)
P
C
C
A
R
D
P
C
C
O
N
T
R
O
L
I
N
L
A
N
O
U
T
S
R
R
C
E
M
M
T
R
O
I
T
G
E
E
G
1
2
E
R
E
O
T
I
N
Carrying handle  
Air filter (Right)  
Speaker 5W (Stereo)  
O
U
T
A
C
I
N
Lens hood cap  
AC INPUT  
Connect the supplied  
power cable’s three-pin  
plug here.  
Foot (four)  
Rotate to fine-adjust the height of  
each foot (max. 0.6”/15mm).  
*NOTE: Slot for Kensington MicroSaver Security System  
This security slot supports the MicroSaver® Security System.  
MicroSaver® is a registered trademark of Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.  
Attaching and Removing the Terminal Covers  
To remove the terminal cover, push and hold the latch.  
To attach the terminal cover, align the protrusions inside and push it until you feel it click into place.  
T
S
U
J
D
A
O
T
U
A
S O U R C E  
S
A
U
T
L/  
M
O
N
O
R
L/  
M
O
N
S
L
A
O
T
U
D
1
IO  
R
O
/
/
/  
O
2
1
1-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Depression for foot (4 locations)  
F
Z
FO  
CU  
S
ZO  
O
LE  
FT  
M
UP  
L
E
N
S
S
P
H
IF  
C
C
T
AR  
DO  
W
D
1
RIG  
N
HT  
P
C
C
M
AR  
E
N
D
U
2
LA  
SE  
LEC  
M
E
P
1
N
T
T
E
R
LA  
MP  
2
C
A
N
3
D
3D RE  
C
E
L
ST  
A
FO  
R
TU  
S
M
O
A
AUTO ADJUST  
N
/
P
S
T
OW  
A
N
E
D
R
B
Y
Speaker 5W (Stereo)  
Remote sensor  
Remote sensor  
Ventilation (outlet)  
Air filter (Left)  
Lamp cover 2 (Left)  
Ventilation (outlet)  
Remote sensor  
Air filter (Right)  
1
2
LNA  
ROMTE1  
PCARD  
OTU  
)
(
ROMTE2  
PC  
UBS  
IN  
Ventilation (inlet)  
)
ACIN  
PCNTROL  
IN  
MSOE/HUB  
(
UBS  
OTU  
SCTIGER  
DIV  
SOLT2  
ADUIO  
SOLT1  
RBG1  
LM/NO  
R
RC/r  
ADUIO  
GY/  
AIDOUT  
BC/b  
RBG2  
H/  
L
HV  
R
V
RBGOUT  
SV-IDEO  
VDIEO  
LM/NO  
R
Remote sensor  
L/MNO  
R
1-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Attaching the lens hood cap to the lens hood with the supplied string and rivet  
1. Thread the string through the hole on the lens hood cap.  
Lens hood cap  
String  
2. Use the rivet to attach the string to the bottom of the projector.  
DIV  
Rivet  
PITON2  
ADUIO  
PITON1  
RBG1  
LM/NO  
R
RC/r  
ADUIO  
GY/  
LM/NO  
AIDOUT  
R
BC/b  
RBG2  
/VH  
V
RBGOUT  
SV-IDEO  
LM/NO  
R
VDIEO  
LM/NO  
R
Carrying the Projector  
Always carry your projector by the handle.  
Ensure that the power cable and any other cables connecting to video sources are disconnected before moving the projector.  
When moving the projector or when it is not in use, cover the lens with the lens hood cap.  
CAUTION: Do not put the projector on its side when the lamp is on.  
Doing so may cause damage to the projector.  
FCOUS  
Z
F
PCARD1  
Z
PCARD2  
LFET  
DWON  
LNESHIFT  
L
APM1  
UP  
RGIHT  
L
APM2  
E
N
T
E
R
AUTS  
C
SLECT  
A
N
P
E
M
E
N
U
OS/TANDBY  
3DEFORM  
3D  
OADJUST  
A
1-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Top Features  
14 13 12 10 9 8 11 6 7  
UP  
F
Z
3D  
A
3D REFORM AUTO ADJUST  
LEFT  
LENS SHIFT  
DOWN  
RIGHT  
SELECT  
FOCUS  
ZOOM  
ON/STAND BY  
PC CARD 1  
PC CARD 2  
LAMP 1  
LAMP 2  
STATUS  
POWER  
5
4
3 2  
1
7. AUTO ADJUST Button  
1. POWER Button (ON / STAND BY)(  
)
Use this button to adjust Position-H/V and Pixel Clock/Phase  
for an optimal picture. See page 3-6.  
Use this button to turn the power on and off when the main  
power is supplied and the projector is in standby mode or idle  
mode.  
8. MENU Button  
Displays the menu.  
NOTE: To turn on or off the projector, press and hold this button for a minimum  
of two seconds.  
9. SELECT ̆̄̇̈ (+) (–) / Volume Buttons  
2. POWER Indicator  
̆̄ : Use these buttons to select the menu of the item you  
wish to adjust. When no menus appear, these buttons  
work as a volume control.  
̇̈ : Use these buttons to change the level of a selected menu  
item.A press of the ̈ button executes the selection.When  
the menus or the Viewer tool bar is not displayed, these  
buttons can be used to select a slide, or to move the  
cursor in Folder List or Slide List.  
When this indicator is green, the projector is on; when this  
indicator is orange, it is in standby or idle mode.See the Power  
Indicator section on page 10-3 for more details.  
3. STATUS Indicator  
If this light blinks red rapidly, it indicates that an error has oc-  
curred, the lamp cover is not attached properly or the projector  
has overheated. If this light remains orange, it indicates that  
you have pressed a cabinet key while the Control Panel Key  
Lock is enabled. See the Status Indicator section on page 10-  
3 for more details.  
10. ENTER Button  
Executes your menu selection and activates items selected  
from the menu.  
4. LAMP Indicator 1/2  
11. CANCEL Button  
If this light blinks red rapidly, it's warning you that the lamp has  
reached the end of its usable life. After this light appears, re-  
place the lamp as soon as possible (See page 9-2). See the  
Lamp Indicator section on page 10-3 for more details.  
Press this button to exit "Menus". Press this button to return  
the adjustments to the last condition while you are in the ad-  
justment or setting menu.  
12. LENS SHIFT ̆̄̇̈ Button  
5. PC CARD Access Indicator 1/2  
Adjust the lens offset by shifting the projected image position  
horizontally and / or vertically.  
Lights while accessing a PC card.  
6. 3D REFORM Button  
13. ZOOM Button (+/-)  
Zoom the lens in and out.  
Press this button to enter 3D Reform mode to correct the key-  
stone (trapezoidal) distortion, and make the image square.  
Press to toggle between Cornerstone and Keystone adjust-  
ment mode.  
14. FOCUS Button (+/-)  
Adjust the lens focus.  
NOTE: Pressing and holding this button for a minimum of 2 seconds will reset  
3D Reform correction setting values to zero.  
1-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Terminal Panel Features  
DVI AUDIO Input Mini Jack (Stereo Mini)  
This is where you connect the audio output from your com-  
puter when connected to the DVI input. A commercially avail-  
able audio cable is required.  
2 1  
4. RGB OUT Connector (Mini D-Sub 15 Pin)  
You can use this connector to loop your computer image to an  
external monitor from the RGB 1 or 2 input source.  
DVI  
AUDIO  
3
8
AUDIO OUT  
RGB 1  
SLOT 1  
SLOT 2  
5. VIDEO IN Connector (BNC)  
Connect a VCR, DVD player, laser disc player, or document  
camera here to project video.  
7
4
L/MONO  
L/MONO  
R
R
AUDIO  
RGB 2  
R/Cr  
G/Y  
VIDEO AUDIO Input Jacks R/L (RCA)  
These are your left and right channel audio inputs for stereo  
sound from a Video source.  
RGB OUT  
B/Cb  
6. S-VIDEO IN Connector (Mini DIN 4 Pin)  
Here is where you connect the S-Video input from an external  
source like a VCR.  
VIDEO  
S-VIDEO  
H/  
HV  
NOTE: S-Video provides more vivid color and higher resolution than the tradi-  
tional composite video format.  
V
L/MONO  
R
L/MONO  
S-VIDEO AUDIO Input Jacks R/L (RCA)  
R
These are your left and right channel audio inputs for stereo  
sound from an S-Video source.  
7. AUDIO OUT Jacks R/L (RCA)  
5 6  
You can use this connector to output sound from the currently  
selected input source (RGB 1, RGB 2, DVI (DIGITAL), Video  
or S-Video).  
Output sound level can be adjusted in accordance with the  
sound level of the internal speaker.  
1. RGB 1 Connectors [R/Cr, G/Y, B/Cb, H/V, V] (BNC)  
Connect R,G,B,H (Horizontal sync) and V (Vertical sync) out-  
puts of external equipment.  
If using a component with a combined sync (SYNC) output,  
connect it to the H/V terminal.When using luminance and color-  
difference signals of HDTV and DVD, connect Pr/Cr to the R,Y  
to the G and Pb/Cb to the B input of the projector.  
8. Slot 1/2  
For optional RGB, SDI or DVI board.  
RGB 1 Audio Input Jacks (RCA)  
L/MONO:This is your left channel audio input for stereo sound  
coming from the RGB Input 1 source.  
This also serves as your monaural audio input.  
R:This is your right channel audio input for stereo sound from  
the RGB Input 1 source.  
2. RGB 2 Connector (Mini D-sub 15 Pin)  
Connect your computer or other analog RGB equipment such  
as IBM compatible or Macintosh computers. This also serves  
as a component input connector that allows you to connect a  
component video output of component equipment such as a  
DVD player. This connector also supports SCART output sig-  
nal. See page 2-9 for more details.  
RGB 2 Audio Iput Mini Jack (Stereo Mini)  
This is where you connect audio output from your computer or  
DVD player connected to the RGB2 input.A commercially avail-  
able audio cable is required.  
3. DVI IN Connector (DVI-D 24 Pin)  
This connector can be used to accept digital signal output from  
a computer with a DVI connector.  
1-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Terminal Panel Features  
6. SC. TRIGGER Mini Jack  
When the projector is powered ON the screen trigger output  
sends a low voltage trigger to the screen controller and the  
screen will go down. When the projector is powered OFF the  
screen trigger stops sending a low voltage trigger to the screen  
controller and the screen will go up.  
1 2  
3
4
2
1
NOTE: To use this feature, you must turn on the Screen Trigger function. See  
page 8-17.  
(
)
(
)
USB MOUSE/HUB USB PC  
PC CARD  
Stereo mini cable  
Tip (12V)  
(not supplied)  
LAN  
Ring (0V)  
PC CONTROL  
IN  
7
5
6
REMOTE 1  
REMOTE 2  
8
9
Sleave (ground. 0V)  
OUT  
SC TRIGGER  
NOTE: Screen controllers are supplied and supported by screen manufacturers.  
IN  
OUT  
NOTE: Do not use this jack for anything other than intended use. Connecting  
wired remote control to the SC. TRIGGER Mini Jack causes damage to the re-  
mote control.  
AC IN  
7. LAN Port (RJ-45)  
This port is typically used for UTP Ethernet/Fast Ethernet.Use  
this connector to control the projector on a LAN.  
8. REMOTE 1 (Mini D-Sub 15 Pin)  
This terminal allows external control of the projector by use of  
contact closure. See page 10-9.  
10  
11  
1. USB Port [MOUSE/HUB] (Type A)  
Connect a USB mouse. You can operate the menu or Viewer  
with a USB mouse via this port.  
9. REMOTE 2 Mini Jacks (IN/OUT)  
IN: wired remote control input.  
• A USB-supported scanner or PC peripheral can be connected  
to this port. (USB Hub Function. See page 4-3)  
OUT:for daisy-chaining multiple projectors and operating them  
with the same remote control. To do so, connect to a second  
projector’ s IN terminal to relay the input at the IN terminal of  
the first projector until all the projectors are connected.  
2. USB Port [PC] (Type B)  
Connect this port to the USB port (type A) of your PC using a  
USB cable.This port also serves as a PC Control port by using  
Dynamic Image Utility 2.0 included on the supplied CD-ROM.  
10. Main Power Switch  
When you plug the supplied power cable into an active wall  
outlet and turn on the Main Power switch, the POWER indica-  
tor turns orange and the projector is in standby mode. See  
page 3-2.  
3. PC CARD Slot 1/2  
Insert a PC card, commercially available flash memory card or  
NEC optional wireless LAN card here.  
There are two slots: Slot 1 and Slot 2.  
11. AC IN  
Connect the supplied power cable’s three-pin plug here.  
Three types of power cable are supplied with this projector:  
three-pin type for U.S. A.and Canada.Two-pin type for Europe  
and Japan.  
4. PC CARD Eject Button 1/2  
Press to eject a PC card partially. Each slot has its own eject  
button: 1 and 2.  
5. PC CONTROL Connectors (Mini D-Sub 9 pin)  
For system expansion such as PC-Control using Dynamic Im-  
age Utility included on the supplied User Supportware CD-  
ROM or RS232C control from an external control system.  
IN: connect to the external equipment such as a PC or control  
system.  
OUT:for daisy-chaining multiple projectors and operating them  
with the same external equipment.To do so, connect to a sec-  
ond projector’s IN terminal to relay the input at the IN terminal  
of the first projector until all the projectors are connected.  
1-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
1. POWER ON  
v Remote Control Features  
Press and hold this button for a minimum of two seconds to  
turn on the projector when the main power is supplied and the  
projector is in standby mode or idle mode.  
2. POWER OFF  
Press and hold this button for a minimum of two seconds to  
turn off the projector.  
POWER  
OFF  
ON  
1
3
4
8
2
5
3. MENU  
Press to display the main menu.  
While pressing and holding CTL, press this button to display  
the Remote Control ID dialog box to specify the remote control  
ID. See page 7-2.  
MENU  
ADDRESS  
BS  
-
+
ENTER  
4. ENTER  
Executes the menu selection and activates items selected from  
the menu. When the slider or dialog box is displayed:  
Pressing this button confirms adjustments/setting and returns  
to the previous menu display.  
6
7
ADJUST  
PICTURE WHITE BAL.  
IMAGE  
PROJECTOR  
GHI  
ABC  
DEF  
5. Select (Up/Down/Left/Right)  
1
2
3
̆̄: Use these buttons to select the menu of the item you  
JKL  
MNO  
PQR  
wish to adjust.  
When no menus appear, these buttons work as a volume  
control.  
4
5
6
9
STU  
VWX  
YZ/  
̇̈: Use these buttons to change the level of a selected  
menu item.  
9
8
7
10  
,.  
UNDO CANCEL  
A press of the ̈ button executes the selection.  
0
11  
14  
15  
16  
18  
19  
Pressing and holding CTL, then pressing ̇ button works as a  
Back Space key in the entry screen.  
Pressing and holding CTL, then pressing this button moves  
the menu, slider, toolbar or dialog box.  
12  
13  
TEST  
INFO.  
HELP  
AUTO  
POSITION PIXEL  
17  
LENS  
6. ADJUST WHITE BAL.  
Press to display the Picture Management screen.  
MUTE  
SHUTTER  
7. ADJUST PICTURE  
Press to display the Picture adjustment screen. Pressing this  
button sequentially selects adjustment screens.  
20  
PICTURE  
KEYSTONE AMPLITUDE ENTRYLIST  
SOUND  
OSD  
21  
22  
23  
R
G
B
8. IMAGE/PROJECTOR  
MAGNIFY  
Press to display the Image Option screen.Pressing this button  
sequentially selects Image Options screens.  
While pressing and holding CTL, pressing this button rotates  
Projector Options screens.  
+
+
25  
24  
-
-
9. Source / Input  
Press to select input or to name a signal.  
FOCUS  
CTL  
ZOOM  
LENS  
26  
1
2
3
4
5
6
7
8
9
0
Selects RGB 1 input.  
Selects RGB 2 input.  
Selects DVI (DIGITAL) input.  
Selects VIDEO input.  
Selects S-VIDEO input.  
Selects Viewer input  
Selects LAN input  
Selects OPTION SLOT 1* (available for optional SDI board)  
Selects OPTION SLOT 2* (available for optional SDI board)  
Sequentially selects: RGB1 (VIDEO) → RGB1 (S-VIDEO) .  
*
This button toggles between input 1 and 2.  
NOTE: While pressing and holding CTL, pressing this button switches to the  
selected signal found in the Entry List.  
1-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
10. UNDO  
22. AMPLITUDE (G)  
Press to return the adjustments and settings to the previous  
condition. While pressing and holding CTL, pressing this but-  
ton clears the entire menus or adjustment/setting screen. At  
this time the adjustments/settings are stored in memory ex-  
cept the items on the setting screen with "OK" and "Cancel"  
buttons such as the Menu and the Setup screen.  
Service personnel only.  
When the test pattern is displayed, while pressing and holding  
CTL, pressing this button displays a green test pattern.  
23. ENTRY LIST (B)  
Press to display the Entry List screen.  
Pressing and holding CTL and then ENTRY LIST buttons si-  
multaneously, enters a signal in the Entry List when you are  
not displaying a test pattern.  
11. CANCEL  
Press to exit the menu.  
Press this button with CTL to return to the previous menu with-  
out closing adjustment/setting screen while the menus appear.  
This feature allows you to adjust or set several items concur-  
rently.  
When the test pattern is displayed, while pressing and holding  
CTL, pressing this button displays a blue test pattern.  
24. FOCUS (+/–)  
While pressing and holding CTL, pressing this button allows  
you to adjust the lens focus.  
12. INFO  
Displays the "Source Information" or "Projector Information"  
window. This button toggles between these two windows.  
While pressing and holding CTL, pressing this button stores  
lens position settings.  
25. MAGNIFY/ZOOM (+/–)  
Magnify the size of a target portion.  
While pressing and holding CTL, pressing this button allows  
you to zoom the lens in and out.  
13. TEST  
26. CTL  
Press to display the test pattern. Pressing this button sequen-  
tially selects test patterns.  
Used in conjunction with other buttons, similar to a shift key on  
a computer.  
14. HELP  
Provides online help.  
P
2
I M A G E  
D E F  
W H I T E B A L .  
E N T E R  
A D D R E S S  
T U R E  
15. PIXEL  
A D J U S T  
M E N U  
+
Displays the Position/Clock screen to adjust the clock and  
phase.  
-
O N  
B S  
P O W E R  
O F F  
16. AUTO (RGB only)  
Press to adjust Position-H/V and Pixel Clock for an optimal  
picture.  
27  
28  
17. POSITION  
Press to display the Position screen;press again to display the  
Blanking screen.  
While pressing and holding CTL, pressing this button displays 27. Remote Jack  
the Lens Shift adjustment screen.  
Connect your remote cable here for wired operation.  
18. MUTE SOUND  
28. Infrared Transmitter  
Turns off the sound for a short period of time. Press again to  
restore the sound.  
Direct the remote control toward the remote sensor on the pro-  
jector cabinet.  
19. MUTE OSD  
Press to turn off the on-screen display. Press again to restore  
the on-screen display.  
NOTE: You can also turn off the on-screen display forcibly by pressing and  
holding CTL and then pressing MUTE OSD (Forced On-Screen Mute Mode) ;  
doing this again restores it. In this case any adjustment will still change the  
projector's memory settings. This mode is available even when input is switched  
to another or the power is turned off the main power.  
20. MUTE PICTURE  
Press to turn off the picture for a short period of time. Press  
again to restore the picture.  
21. KEYSTONE (R)  
Press to display the Keystone Correction (3D Reform) screen.  
This button toggles between “Cornerstone” and “Keystone”.  
When the test pattern is displayed, while pressing and holding  
CTL, pressing this button displays a red test pattern.  
NOTE: Pressing and holding this button for a minimum of two seconds will  
reset 3D Reform correction setting values to zero.  
1-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Remote Control Precautions  
Operating Range for Wireless Remote Control  
•
The remote control system may not function when direct sunlight or  
strong illumination strikes the remote control sensor of the main unit, or  
when there is an obstacle in the path.  
The infrared signal operates by line-of-sight up to a distance of  
approximately 7m (20 feet) and a 60 degree angle of the remote  
sensor.  
The projector will not function if there are objects between the  
remote sensor and the remote control or if strong light falls on  
the remote sensor.Weak batteries will also prevent the projector  
from operating properly.  
•
When remote control buttons are pressed and held, projector’s function  
keys may not operate.  
•
•
Do not subject to strong shock.  
Do not allow water or other liquid to splash on the remote control. If the  
remote control gets wet, wipe it dry immediately.  
•
•
Avoid exposure to heat and steam.  
Remove the batteries from the remote control when the remote control  
is not going to be used for a long period.  
Side View  
30˚  
Remote Control Battery Installation  
7m  
Installing the Remote Control Batteries  
When it comes time to replace the batteries, two "AAA" type will  
be required.  
30˚  
Remote sensors on the  
projector cabinet  
1. Press and open the cover.  
7m  
2. Align and insert the batteries according to the (+) and (-) indications  
inside the case.  
Remote control  
NOTE: You cannot operate the projector using the remote control if:  
• The remote control ID is not set to [None].  
• The remote ID is not the same as the projector ID.  
See page 7-2 for setting remote ID and projector ID.  
3. Replace the cover.  
1-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Using the Remote Control in Wired Operation  
Connect one end of the supplied remote cable to the REMOTE 2 IN  
mini jack and the other end to the remote jack on the remote control.  
NOTE: Do not use this jack for anything other than intended use. Connecting the wired  
remote control to the SC. TRIGGER Mini Jack causes damage to the remote control.  
2
1
(
)
(
)
USB MOUSE/HUB USB PC  
PC CARD  
/
REMOTE 2  
IN  
PC CONTROL  
IN  
OUT  
SC TRIGGER  
REMOTE  
2
/  
IN  
OUT  
AC IN  
/
/
Terminal panel (Right)  
Remote cable (supplied)  
1-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
Installation  
z Setting Up Your Projector..........................................2-2  
Screen Size and Projection Distance .................................................................. 2-2  
x Lens Shift Adjustable Range ....................................2-4  
c Optional Lens Installation .........................................2-6  
v Making Connections .................................................2-8  
Connecting Your PC or Macintosh ....................................................................... 2-8  
To connect Scart Output................................................................................. 2-9  
Connecting an External Monitor .......................................................................... 2-9  
Connecting Your DVD Player ............................................................................. 2-10  
Connecting Your VCR or Laser Disc Player ....................................................... 2-11  
Connecting the Supplied Power Cable .............................................................. 2-11  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
This chapter describes how to set up your projector and how to connect video and audio sources.  
z Setting Up Your Projector  
Your Projector is simple to set up and use. But before you get started, you must first:  
1. Determine the image size  
4. Connect the supplied power cable.  
5. Set up the projector.  
2. Set up a screen or select a non-glossy white wall onto which you can  
project your image.  
6. Connect a PC, VCR, DVD player, or other equipment.  
7. Make settings or adjustments on the projector.  
3. Install the optional lens to the projector.  
Screen Size and Projection Distance  
Applicable lens and throw distance/ List of screen sizes  
List of Screen Sizes  
Screen size  
Width (H)  
Height (V)  
m
0.8  
1.2  
1.6  
2.0  
2.4  
3.0  
4.1  
5.1  
6.1  
8.1  
10.2  
inch  
31.5  
47.2  
63.0  
78.7  
m
inch  
23.6  
35.4  
47.2  
59.1  
70.9  
90.6  
118.1  
149.6  
181.1  
240.2  
299.2  
40"  
60"  
80"  
0.6  
0.9  
1.2  
1.5  
1.8  
2.3  
3.0  
3.8  
4.6  
6.1  
7.6  
Height  
100"  
120"  
150"  
200"  
250"  
300"  
400"  
500"  
Screen size (Diagonal)  
94.5  
118.1  
161.4  
200.8  
240.2  
318.9  
401.6  
Formulas:  
Screen width H (m)= Screen size
ן
4/5
ן
0.0254  
Screen height V (m)= Screen size
ן
3/5
ן
0.0254  
Screen width H (inch)= Screen size
ן
4/5  
Screen height V (inch)= Screen size
ן
3/5  
Width  
Table of Throw Distances and Screen Sizes for Optional Lenses  
GT19ZL  
1.7-2.2  
GT20ZL  
2.0-2.6  
(inches)  
GT24ZLB  
2.2-3.2  
GT34ZLB  
3.2-4.8  
(inches)  
GT10RLB  
1.0  
(m) (inches)  
GT13ZLB  
1.2-1.5  
(m)  
(inches)  
(m)  
(inches)  
(m)  
(m)  
––  
(inches)  
––  
(m)  
––  
––  
––  
––  
40" 0.76 30.0 0.91 - 1.15 36.0 - 45.2 1.30 - 1.74 51.0 - 68.4 1.53 - 2.03 60.1 - 80.0  
––  
––  
––  
––  
60" 1.17 46.1 1.40 - 1.75 55.2 - 69.0 1.99 - 2.65 78.3 - 104.2 2.34 - 3.10 92.1 - 122.0 2.58 - 3.86 101.6 - 152.0  
67" 1.31 51.7 1.57 - 1.97 62.0 - 77.4 2.23 - 2.97 87.8 - 116.7 2.62 - 3.47 103.3 - 136.7 2.90 - 4.32 114.0 - 170.3  
72" 1.41 55.7 1.70 - 2.12 66.8 - 83.3 2.40 - 3.19 94.6 - 125.7 2.83 - 3.74 111.3 - 147.2 3.12 - 4.66 122.9 - 183.3  
80" 1.58 62.1 1.89 - 2.36 74.5 - 92.9 2.68 - 3.56 105.5 - 140.0 3.15 - 4.16 124.1 - 164.0 3.48 - 5.19 137.1 - 204.3 5.10 - 7.81 200.6 - 307.6  
84" 1.66 65.3 1.99 - 2.48 78.3 - 97.6 2.82 - 3.74 110.9 - 147.2 3.32 - 4.38 130.6 - 172.4 3.66 - 5.45 144.2 - 214.7 5.36 - 8.21 211.0 - 323.3  
90" 1.78 70.2 2.14 - 2.66 84.1 - 104.8 3.02 - 4.01 119.1 - 158.0 3.56 - 4.70 140.2 - 185.0 3.93 - 5.85 154.8 - 230.4 5.76 - 8.81 226.6 - 346.9  
100" 1.99 78.2 2.38 - 2.96 93.7 - 116.7 3.37 - 4.47 132.7 - 175.9 3.97 - 5.23 156.2 - 205.9 4.38 - 6.52 172.6 - 256.5 6.41 - 9.81 252.5 - 386.2  
120" 2.39 94.2 2.87 - 3.57 112.9 - 140.5 4.06 - 5.38 159.9 - 211.7 4.78 - 6.30 188.2 - 247.9 5.28 - 7.84 208.0 - 308.8 7.73 -11.81 304.5 - 464.8  
150" 3.01 118.3 3.60 - 4.48 141.8 - 176.2 5.10 - 6.74 200.7 - 265.4 6.00 - 7.90 236.3 - 310.9 6.64 - 9.83 261.3 - 387.2 9.71 -14.80 382.3 - 582.7  
180" 3.62 142.4 4.33 - 5.38 170.6 - 212.0 6.14 - 8.11 241.6 - 319.2 7.22 - 9.50 284.3 - 373.9 7.99 -11.83 314.5 - 465.6 11.69 -17.80 460.2 - 700.6  
200" 4.02 158.5 4.82 - 5.99 189.9 - 235.8 6.83 - 9.02 268.8 - 355.0 8.04 -10.56 316.3 - 415.8 8.89 -13.15 350.0 - 517.9 13.01 -19.79 512.1 - 779.2  
210" 4.23 166.5 5.07 - 6.29 199.5 - 247.7 7.17 - 9.47 282.4 - 372.9 8.44 -11.10 332.4 - 436.8 9.34 -13.82 367.7 - 544.0 13.67 -20.79 538.1 - 818.5  
240" 4.84 190.6 5.80 - 7.20 228.4 - 283.4 8.21 -10.84 323.2 - 426.7 9.66 -12.69 380.4 - 499.8 10.69 -15.81 421.0 - 622.4 15.64 -23.79 615.9 - 936.5  
250" 5.04 198.6 6.04 - 7.50 238.0 - 295.4 8.56 -11.29 336.8 - 444.6 10.07 -13.23 396.4 - 520.8 11.14 -16.47 438.7 - 648.6 16.30 -24.78 641.9 - 975.8  
270" –– –– 6.53 - 8.11 257.2 - 319.2 9.25 -12.20 364.0 - 480.4 10.88 -14.29 428.5 - 562.8 12.04 -17.80 474.2 - 700.8 17.62 -26.78 693.8 -1,054.4  
300" –– –– 7.27 - 9.01 286.1 - 354.9 10.28 -13.57 404.9 - 534.1 12.10 -15.89 476.5 - 625.7 13.40 -19.79 527.4 - 779.2 19.60 -29.78 771.7 -1,172.3  
400" –– ––  
500" –– ––  
––  
––  
––  
––  
––  
––  
––  
––  
––  
––  
––  
––  
17.90 -26.43 704.9 -1,040.6 26.19 -39.761,031.2  
–– –– 32.79 -49.741,290.8  
-
-
1,565.3  
1,958.4  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
GT24ZLB (H
ן
2.2) -(H
ן
3.2)  
GT19ZL (H
ן
1.7) -(H
ן
2.2)  
GT10RLB (H
ן
1.0)  
GT13ZLB (H
ן
1.2) -(H
ן
1.5)  
GT20ZL (H
ן
2.0) -(H
ן
2.6)  
GT34ZLB (H
ן
3.2) -(H
ן
4.8)  
Throw distance  
For screen sizes between 40" and 500" not indicated on the above table, use formulas below.  
Projection Distance= Screen Width (H) 
ן
 Lens Magnification  
Throw distance for GT10RLB (m/inch)=H 
ן
 1.0 Distance from 0.8m to 5.0m/31.5" to 196.9"  
Throw distance for GT13ZLB (m/inch)=H 
ן
 1.2 through H 
ן
 1.5 Distance from 1.0m to 9.0m/39.37" to 354.3"  
Throw distance for GT19ZL (m/inch)=H 
ן
 1.7 through H 
ן
 2.2 Distance from 1.4m to 13.5m/55.12" to 531.5"  
Throw distance for GT20ZL (m/inch)=H 
ן
 2.0 through H 
ן
 2.6 Distance from 1.7m to 15.8m/66.93" to 622"  
Throw distance for GT24ZLB (m/inch)=H 
ן
 2.2 through H 
ן
 3.2 Distance from 2.6m to 26.4m/102.4" to 1039"  
Throw distance for GT34ZLB (m/inch)=H 
ן
 3.2 through H 
ן
 4.8 Distance from 5.1m to 49.7m/200.8" to 1957"  
NOTE: Distances may vary +/-5%.  
NOTE: Lens shift is not available on GT10RLB(Short throw fixed-focus lens). GT10RLB should be used only for “zero degree/no-offset” applications.  
NOTE: When using the projector with either the GT13ZLB or GT13ZL lens, it is recommended to select "Dual" in the Lamp Settings menu. This will provide the best  
performance when operating the projector.  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
x Lens Shift Adjustable Range  
Lens Shift Range for Desktop and Ceiling Mount Application  
The diagram below shows the location of the image position in the lens. The lens can be shifted within the shaded area as shown  
using the normal projection position as a starting point.  
Maximum Possible Range for GT20ZL:  
Up: 0.5 V  
Down: 0.5 V  
Right: 0.32 H  
Left: 0.32 H  
(H: width of projected image, V: height of projected image)  
NOTE: If lens is shifted in two directions combined, maximum range in either direction cannot be obtained due to rounded off area near edge of lens. (example: shift up  
and right) See diagram below.  
1H  
0.32H  
0.32H  
0.5V  
Desktop/Front  
Vertical  
0.5V  
1V  
1V  
Normal position  
Normal projection position  
0.5V  
1H  
Ceiling/Front  
Vertical  
0.32H 0.32H  
Normal position  
0.5V  
1V  
Normal position  
Horizontal  
WARNING  
*
Installing your projector on the ceiling must be done by a qualified  
technician. Contact your NEC dealer for more information.  
*
•
Do not attempt to install the projector yourself.  
To avoid premature lamp failure, do not tilt the front of the projector up  
or down by more than 45° from level.  
Range of lens shift range on GT20ZL  
Vertical: 11.30° to 8.18°  
•
•
Only use your projector on a solid, level surface. If the projector falls  
to the ground, you can be injured and the projector severely dam-  
aged.  
Horizontal: 9.67° to 7.00°  
When performing the lens shift both vertically and horizontally,  
the angle on some corners may become narrower than the above-  
mentioned one.  
Do not use the projector where temperatures vary greatly. The pro-  
jector must be used at temperatures between 32°F (0°C) and 95°F  
(35°C).  
•
•
Do not expose the projector to moisture, dust, or smoke. This will  
harm the screen image.  
Ensure that you have adequate ventilation around your projector so  
heat can dissipate. Do not cover the vents on the side or the front of  
the projector.  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
Lens Shift Adjustable Range  
Lens Shift Range for Desktop and Ceiling Mount Application  
The diagram below shows the location of the image position in the lens. The lens can be shifted within the shaded area as shown  
using the normal projection position as a starting point.  
Maximum Possible Range for GT13ZLB/GT19ZL/GT24ZLB/GT34ZLB:  
Values in parentheses for GT13ZLB.  
Up: 0.39V (0.32V)  
Down: 0.39V (0.32V)  
Right: 0.24H (0.19H)  
Left: 0.24H (0.19H)  
(H: width of projected image, V: height of projected image)  
NOTE: If lens is shifted in two directions combined, maximum range in either direction cannot be obtained due to rounded off area near edge of lens. (example: shift up  
and right) See diagram below.  
0.24H  
0.24H  
(0.19H)  
1H  
(0.19H)  
0.39V  
(0.32V)  
Desktop/Front  
Vertical  
0.39V  
(0.32)  
1V  
1V  
Normal position  
Normal projection position  
0.39V  
(0.32V)  
1H  
0.24H  
0.24H  
(0.19H) (0.19H)  
Ceiling/Front  
Vertical  
Normal position  
0.39V  
(0.32)  
1V  
Normal position  
Horizontal  
WARNING  
*
Installing your projector on the ceiling must be done by a qualified  
technician. Contact your NEC dealer for more information.  
Range of lens shift range on GT13ZLB, GT19ZL, GT24ZLB and  
GT34ZLB  
GT13ZLB Vertical: 12.05° to 9.22°  
*
•
Do not attempt to install the projector yourself.  
To avoid premature lamp failure, do not tilt the front of the projector up  
or down by more than 45° from level.  
Horizontal: 9.59° to 7.32°  
•
•
Only use your projector on a solid, level surface. If the projector falls  
to the ground, you can be injured and the projector severely dam-  
aged.  
GT19ZL  
Vertical: 10.39° to 7.49°  
Horizontal: 8.56° to 6.15°  
GT24ZLB Vertical: 8.06° to 5.14°  
Horizontal: 6.63° to 4.22°  
GT34ZLB Vertical: 5.33° to 3.42°  
Horizontal: 3.29° to 2.81°  
When performing the lens shift both vertically and horizontally,  
the angle on some corners may become narrower than the above-  
mentioned one.  
Do not use the projector where temperatures vary greatly. The pro-  
jector must be used at temperatures between 32°F (0°C) and 95°F  
(35°C).  
•
•
Do not expose the projector to moisture, dust, or smoke. This will  
harm the screen image.  
Ensure that you have adequate ventilation around your projector so  
heat can dissipate. Do not cover the vents on the side or the front of  
the projector.  
2-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
c Optional Lens Installation  
This section describes how to install the lens.  
Before installation  
*
*
Determine the optional lens to be used to obtain a desired projection distance. There are six optional lenses available:  
GT13ZLB, GT19ZL, GT20ZL, GT24ZLB and GT34ZLB (Zoom lens)  
GT10RLB (Short throw fixed-focus lens)  
Press the power button (ON/STAND BY) on the projector or POWER OFF button on the remote control for a minimum of two seconds to turn off the  
power, wait 90 seconds for the cooling fan to stop, turn off the main power switch then disconnect the power cable.  
Check that the projector has cooled off sufficiently before proceeding.  
CAUTION  
* The projector and lens contain high-precision parts. Do not induce shock to the projector or the lens.  
* Do not touch the lens surface. Doing so can degrade the optical performance.  
Preparation: Tools needed for installation:  
A hexagonal driver and dust-protective sheets are supplied with the optional lens.  
1. Remove the lens hood cap and lens hood.  
q Remove the lens hood cap.  
w Loosen and remove the 2 screws on the lens hood using the hexagonal driver.  
e Remove the lens hood by pushing down and pulling the top toward you.  
S
-VIDEO
L
3
Lens hood  
U
S
B
(
M
O
U
SE/HU  
B
)
U
S
B
(
P
C
)
P
C
C
A
R
D
P
C
C
O
1
N
T
R
OL  
Lens hood cap  
IN  
L
A
N
O
U
T
S
R
R
C
E
TR  
IG  
M
M
O
T
E
E
G
1
2
E
R
E
O
T
IN  
O
U
T
A
1
C
IN  
3
2
2. Attach a dust-protective sheet.  
q Remove the shipping tape on the back of the lens hood. w Insert the dust-protective sheet included with your optional lens. Be  
careful not to fold the sheet.  
Align the holes on  
Hole  
the right.  
1
2
Shipping tape  
Insert the dust-protec-  
tive sheet with the alu-  
minum side up while  
bending it.  
2-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
3. Mount the lens unit on the projector and connect the extension cable attached to the projector.  
q Remove the lens cap from the rear end of the lens unit.  
NOTE: Leave the front lens cap for protection while mounting the lens unit.  
w Insert the lens unit so that the 4 screws on the lens unit are properly lined up with the 4 holes on the lens mount.  
e Secure the 4 screws using the hexagonal driver.  
r Insert the connector of the lens unit fully into the socket of the extension cable attached to the projector.  
NOTE: The GT13ZL, GT19ZL, GT24ZL and GT34ZL optional lenses have one connector. The B type lenses (GT13ZLB, GT24ZLB and GT34ZLB) and  
GT20ZL have two connectors.  
To insert the connector into the 4-pin socket on the right side.  
1
D
I
L/M  
L/MONO  
R
G
ONO  
R
R
S
L
SL
L/MO  
O
T
A
U
A
U
D
L/MONO  
R
D
1
IO  
NO  
R
G
B
R
IO  
G
2
B
2
S
R
L
S
LOT  
R
O
/C  
T
R
/C  
r
2
r
2
R
G
R
B
GB OUT  
O
U
T
G
/Y  
G
/Y  
V
ID  
V
ID  
E
O
E
O
S-V  
S
B
/C  
-V  
ID  
B
/C  
ID  
b
V
EO  
b
E
O
H/H  
H/HV  
L/MONO  
R
L/MONO  
R
V
V
L/MONO  
L/MONO  
R
R
3
2
R
E
M
O
T
E
2
IN  
O
U
T
A
C
IN  
4
Lens shift defection switch  
CAUTION: There is a lens shift detection switch for the moving  
gears of the lens shift motors used to reduce the risk of pinching  
fingers. Do not defeat this feature.  
4. Reinstall the lens hood.  
q Remove the front lens cap from the lens unit.  
w Insert the lens hood so that the grooves on the 4 corners of the lens hood  
are properly lined up with the 4 catches on the projector.  
e Secure the 2 screws using the hexagonal driver.  
This completes installation. If necessary, put the lens hood cap on the lens  
hood.  
L
/M  
O
N
O
R
SLO
L
A
/M  
O
U
D
IO  
N
O
R
G
B
2
SLOT  
R
R
/C  
r
RGB OUT  
G
/Y  
V
ID  
E
O
S
-
V
B
/C  
ID  
b
E
O
H
/H  
V
L
/M  
O
N
O
V
L
/M  
O
N
R
R
USB(M  
O
U
2
S
E
/H  
U
B
)
USB  
(PC)  
2
PC CAR
L
/M  
O
PC CONTROL  
N
O
R
S
S
L
L
O
T
AUDIO  
/
M
O
IN  
N
1
RG  
O
B
2
LAN  
R
L
R/Cr  
O
T
R
OT  
G
B
O
U
T
SC TRIGGER  
REMOTE  
REMOTE  
1
2
G/Y  
VID  
EO  
S
-V  
B/Cb  
ID  
EO  
IN  
H
/H  
V
OUT  
L
/M  
O
N
O
V
L
/M  
O
N
O
AC IN  
R
R
U
S
B
(
MOUSEHUB  
)
U
S
B
2
(P  
C
)
P
C
C
A
R
D
P
C
C
O
N
T
R
O
L
I
N
L
A
N
O
U
T
S
R
R
C
E
M
M
T
R
O
I
G
T
E
E
G
1
2
E
R
E
O
T
I
N
O
U
T
1
A
C
I
N
3
2-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
v Making Connections  
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most cases  
signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.  
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software.  
* If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER button again to resume.  
When Viewing a DVI Digital Signal:  
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI-D signal cable (not supplied) before turning on your PC or  
projector. Turn on the projector first and select DVI (DIGITAL) from the source menu before turning on your PC.  
Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should this happen, restart your PC.  
Do not disconnect the DVI-D signal cable while the projector is running. If the signal cable has been disconnected and then re-connected, an image may  
not be correctly displayed. Should this happen, restart your PC.  
NOTE:  
•
Use the DVI-D cable compliant with DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0 standard. The DVI-D cable should be within 5 m  
(196") long.  
•
The DVI (DIGITAL) connector accepts VGA (640x480), SVGA (800x600), 1152x864, XGA (1024x768) and SXGA (1280x1024 @ up to 60Hz).  
Connecting Your PC or Macintosh Computer  
DVI  
DVI  
AUDIO  
AUDIO OUT  
RGB  
1
SLOT  
1
SLOT  
2
L/MONO  
L/MONO  
R
R
AUDIO  
RGB  
2
R/Cr  
G/Y  
RGB 1  
RGB UT  
RGB 2  
B/Cb  
VIDEO  
S-VIDEO  
H/  
HV  
V
L/MONO  
R
L/MNO  
R
Audio cable (not supplied)  
BNC
ן
5 cable (not supplied)  
Audio cable (not supplied)  
IBM PC or Compatibles (Desktop type)  
or Macintosh (Desktop type)  
RGB signal cable  
(not supplied)  
To mini D-Sub 15-pin connec-  
tor on the projector.  
PHONE  
DVI-D cable with ferrite core  
(not supplied)  
Audio cable (not supplied)  
NOTE: For older  
Macintosh, use a com-  
mercially available pin  
adapter (not supplied)  
to connect to your  
Mac's video port.  
PHONE  
IBMVGA or Compatibles (Notebook type)  
or Macintosh (Notebook type)  
Connecting your PC or Macintosh computer to your projector will en-  
able you to project your computer's screen image for an impressive pre-  
sentation.  
Connecting to RGB 1 IN connectors (BNC)  
Use a BNC
ן
5 cable (not supplied) to connect your PC and the RGB 1  
IN connectors on your projector.  
To connect to a PC or Macintosh, simply:  
Connecting to RGB2 IN connector (D-Sub 15 Pin)  
1. Turn off the power to your projector and computer.  
Use an RGB signal cable (not supplied) to connect your PC and the  
RGB2 IN connector on your projector.  
2. Use a commercially available signal cable to connect your  
PC or Macintosh to the projector.  
Connecting Your PC with a DVI Connector  
3. Turn on the projector and the computer.  
Use a DVI-D signal cable (not supplied) to connect a DVI connector of  
your PC to the projector.  
4. If the projector goes blank after a period of inactivity, it may  
be caused by a screen saver installed on the computer you've  
connected to the projector.  
NOTE: The GT5000 is not compatible with video decoded outputs of NEC ISS-  
6020 and ISS-6010 switcher.  
2-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
To connect SCART output (RGB)  
Before connections: An exclusive SCART adapter (ADP-SC1) and a  
commercially available SCART cable are required for this connection.  
1. Turn off the power to the projector and your video equipment.  
2. Use the NEC ADP-SC1 SCART adapter and a commercially  
available SCART cable to connect the RGB 2 input of your  
projector and a SCART output (RGB) of your video equipment.  
NOTE:  
• Audio signal is not available for this connection.  
• The RGB 1 IN connector does not support Plug & Play.  
3. Turn on the power to the projector and your video equipment.  
4. Use the RGB 2 button on the remote control to select the RGB  
2 input.  
Projector  
Video equipment  
such as DVD player  
DVI  
AUDIO  
5. Press the MENU button on the remote control to display the  
menu.  
A
U
D
I
O
O
U
T
RGB  
1
SLOT  
1
SLOT  
2
B  
A
B  
B
C
C
L/MONO  
L/MONO  
R
R
P
AUDIO  
RGB  
2
R/Cr  
G/Y  
R
G
B
O
U
T
B/Cb  
C
VIDEO  
S-VIDEO  
RGB 2  
H/  
HV  
V
L/MONO  
R
L/MONO  
C
I
R
6. From the Advanced menu, select [Projector Options] → [Setup]  
→ [Page 3] → [Signal Select RGB2] → [Scart].  
SCART is a standard European audio-visual connector forTVs,  
VCRs and DVD players. It is also referred to as Euro-connec-  
tor.  
To RGB 2 IN  
Commercially available Female  
SCART cable  
ADP-SC1  
NOTE: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Europe.  
Contact your NEC dealer in Europe for more information.  
Connecting an External Monitor  
DVI  
AUDIO  
AUDIO OUT  
RGB  
1
SLOT  
1
SLOT  
2
L/MONO  
R
/
R
AUDIO  
RGB  
2
R/Cr  
G/Y  
RGB OUT  
B/Cb  
VIDEO  
SVIDEO  
RGB OUT  
V
L/MONO  
L/MONO  
R
R
Audio cable  
(not supplied)  
RGB signal cable  
(not supplied)  
To mini D-Sub 15-pin connec-  
tor on the projector.  
LINE IN  
Audio cable  
(not supplied)  
RGB signal cable  
(not supplied)  
To mini D-Sub 15-pin connec-  
tor on the projector.  
PHONE  
You can connect a separate, external monitor to your projector to simulta-  
neously view on a monitor the RGB analog image you're projecting.To do  
so:  
NOTE:  
•
The RGB OUT connector outputs RGB signal during idle mode (See page 8-15).  
When the projector goes into idle mode, the image on an external monitor dis-  
appears for a moment. Note that the RGB OUT connector will not output RGB  
signal during Standby mode.  
When the projector is in the Idle mode, the image may not be correctly dis-  
played while the cooling fans are running immediately after turning on or off the  
power. Note that the RGB OUT connector will not output RGB signal during  
Standby mode.  
1. Turn off the power to your projector, monitor and computer.  
•
2. Use a 15-pin cable to connect your monitor to the RGB OUT  
(Mini D-Sub 15 pin) connector on your projector.  
3. Turn on the projector, monitor and the computer.  
•
Daisy chain connection is not possible.  
2-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
Connecting Your DVD Player  
DVI  
AUDIO  
AUDIO OUT  
RGB  
1
S
RGB 1  
L/MONO  
L/MONO  
R
R
AUDIO  
RGB  
2
R/Cr  
G/Y  
RGT  
Optional 15-pin-to-RCA  
(female)
ן
3 cable (ADP-CV1)  
B/Cb  
RGB 2  
VIDEO  
S-VIDEO  
H/  
HV  
V
L/MONO  
R
L/MONO  
R
RCA(female)-to-BNC(male)  
adapter (not supplied)  
Component video RCA
ן
3 cable  
(not supplied)  
Audio cable (not supplied)  
Audio Equipment  
AUDIO IN  
DVD player  
L
R
L
R
Y
Cb Cr  
AUDIO OUT  
Component  
Audio cable (not supplied)  
You can connect your projector to a DVD player with component output or  
Video output. To do so, simply:  
For a DVD player without a component video (Y,Cb,Cr) output,  
use an S-Video cable (not supplied) to connect an S-Video  
output of the DVD player to the S-Video input of the projector.  
Use an appropriate type of audio cable (not supplied) to con-  
nect the desired type of audio from your DVD player to your  
audio equipment.  
1. Turn off the power to your projector and DVD player.  
2. If your DVD player has the component video (Y,Cb,Cr) output,  
use a commercially available component video cable (RCAX3)  
and the optional 15-pin-to-RCA (female)
ן
3 cable to connect  
your DVD player to the RGB 1 IN or 2 IN connector on the  
projector.  
3. Turn on the projector and DVD player.  
NOTE: Refer to your DVD player's owner's manual for more information about your  
DVD player's video output requirements,  
2-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
Connecting Your VCR or Laser Disc Player  
DVI  
AUDIO  
AUDIO OUT  
RGB  
1
SLOT  
1
SLOT  
2
L/MONO  
L/MONO  
R
R
AUDIO  
RGB  
2
R/Cr  
G/Y  
RGB OUT  
B/Cb  
VIDEO  
VIDO  
S-VIDEO  
S-VIDEO  
H/  
HV  
V
/MONO  
R
L/MONO  
R
Video cable (not supplied)  
Audio cable (not supplied)  
S-video cable (not supplied)  
Audio equipment  
VCR/ Laser disc player  
AUDIO IN  
L
R
L
R
S-VIDEO VIDEO  
VIDEO OUT  
AUDIO OUT  
Audio cable (not supplied)  
Use common RCA cables (not provided) to connect your VCR, laser disc  
player or document camera to your projector.  
To make these connections, simply:  
NOTE: Refer to your VCR or laser disc player owner's manual for more information  
about your equipment's video output requirements.  
NOTE: An image may not be displayed correctly when a Video or S-Video source is  
played back in fast-forward or fast-rewind via a scan converter.  
1. Turn off the power to the projector and VCR, laser disc player  
or document camera.  
2. Connect one end of an RCA cable (not supplied) to the video  
output connector on the back of your VCR or laser disc player,  
connect the other end to the Video input on your projector (an  
RCA to BNC adapter is necessary). Use an audio cable (not  
supplied) to connect the audio from your VCR or laser disc  
player to your audio equipment (if yourVCR or laser disc player  
has this capability). Be careful to keep your right and left chan-  
nel connections correct for stereo sound.  
3. Turn on the projector and the VCR or laser disc player.  
Connecting the Supplied Power Cable  
U
O  
/
Connect the supplied power cable to the projector.  
First connect the supplied power cable's three-pin plug to  
the AC IN of the projector, and then connect the other  
plug of the supplied power cable in the wall outlet.  
L
I
/
/
/
L
M  
O
USB  
(
M
O
U
S
E
/H  
U
B)  
USB  
(
1
P
C
)
PC CAR
PC CO  
NTROL  
I
LAN  
OU
SC  
REM  
REM  
T
RIGGER  
OTE  
OTE  
1
2
IN  
OUT  
AC IN  
2-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Projecting an Image  
(Basic Operation)  
z Turning on the Projector............................................3-2  
x Selecting a Source ...................................................3-3  
c Adjusting the Picture Size and Position ....................3-3  
v Correcting the Horizontal and  
Vertical Keystone Distortion (3D Reform) ................3-4  
b Optimizing RGB Picture Automatically .....................3-6  
n Turning Up or Down Volume .....................................3-6  
m Turning off the Projector............................................3-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image  
This chapter describes how to turn on the projector and to project a pic-  
ture onto the screen.  
2. Press the ENTER button to execute the selection.  
z Turning on the Projector  
3D  
A
3D REFORM AUTO ADJUST  
SELECT  
NOTE:  
• When plugging in or unplugging the supplied power cable, make sure that the  
main power switch is pushed to the off[O] position. Failure to do so may cause  
damage to the projector.  
ON/STAND BY  
L
STATUS  
POWER  
• The projector has two power switches: main power switch and POWER button  
(POWER ON and OFF on the remote control)  
• The projector has a feature to prevent itself from being used by unauthorized  
individuals. To use this feature, register your PC card as a protect key. See "Secu-  
rity" in "Projector Options" on page 8-23 for more details.  
3. The Basic menu will be displayed in the language you have selected.  
To turn on the main power to the projector,  
press the Main Power switch to the ON posi-  
tion ( I ).  
Flashing for 1  
minute.  
Standby  
Steady light  
POWER  
POWER  
POWER  
ON/SND BY  
Steady orange  
light  
Flashing green  
light  
Steady green  
light  
Before you turn on your projector, ensure that the computer or video source  
is turned on and that your lens hood cap is removed.  
Only after you press the ON/STAND BY button on the projector cabinet or  
POWER ON button on the remote control for a minimum of 2 seconds will  
the power indicator turn to green and the projector become ready to use.  
To close the menu, press the CANCEL button.  
3D  
A
3D REFORM AUTO ADJUST  
SELECT  
3D  
A
3D REFORM AUTO ADJUST  
SELECT  
ON/STAND BY  
ON/STAND BY  
LAMP 2  
STAT
WER  
LAMP 2  
STATUS  
POWER  
After this has been done, you can proceed to the advanced menu opera-  
tion.  
NOTE: You cannot turn off the projector for 60 seconds immediately after turning  
on the projector.  
If you want, you can select the menu language later. See "Language" on  
page 8-13.  
Note on Startup screen (Menu Language Select screen)  
NOTE: To turn the projector on by plugging in the power cable, first turn on the  
Main Power switch to ON and use the menu and enable the "Auto Start" feature.  
(See page 8-16.) Immediately after turning on the projector, screen flicker may  
occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.  
When you first turn on the projector, you will get the Startup screen. This  
screen gives you the opportunity to select one of the seven menu lan-  
guages: English, German, French, Italian, Spanish, Swedish and Japa-  
nese.  
•
If one of the following things happens, the projector will not turn on.  
To select a menu language, follow these steps:  
*
If the internal temperature of the projector is too high, the projector  
detects abnormal high temperature. In this condition the projector will  
not turn on to protect the internal system. If this happens, wait for the  
projector's internal components to cool down.  
1. Use the SELECT ̆ or ̄ button to select one of the seven languages  
for the menu.  
*
*
When the lamp reaches its end of usable life, the projector will not turn  
on. If this happens, replace the lamp.  
3D  
A
3D REFORM AUTO ADJUST  
SELECT  
If the lamp fails to light, and if the LAMP indicator 1 or 2 flashes on and  
off in a cycle of six times, wait a full minute and then turn on the power.  
ON/STAND BY  
LAMP 2  
STATUS  
POWER  
3-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image  
x Selecting a Source  
c Adjusting the Picture Size and Position  
Selecting the computer or video source  
1. Turn on the projector  
2. Select your type of projector orientation.  
Desktop front, ceiling rear, desktop rear, and ceiling front.  
Using the Remote Control  
POWER  
OFF  
ON  
Press the Source/Number button (0-9) to se-  
lect input.  
MENU  
ADDRESS  
ENTER  
BS  
1 ...... RGB 1 input  
2 ...... RGB 2 input  
3 ...... DVI (DIGITAL) input  
4 ...... VIDEO input  
5 ...... S-VIDEO input  
6 ...... Viewer  
-
+
ADJUST  
PICTURE WHITE BAL.  
IMAGE  
PROJECTOR  
GHI  
ABC  
DEF  
1
2
3
JKL  
MNO  
PQR  
4
5
6
STU  
VWX  
YZ /  
7 ...... LAN  
9
7
8
,.  
UNDO CANCEL  
8 ...... SLOT 1  
3. Display the test pattern by pressing the TEST button on the remote  
control or using the menu.  
0
9 ...... SLOT 2  
TEST  
INFO.  
HELP  
AUTO  
0 ...... Sequentially selects:  
RGB1 (VIDEO) → RGB2 (S-VIDEO) →  
RGB1 (VIDEO) ........  
POSITION PIXEL  
LENS  
TEST  
MUTE  
SHUTTER  
PICTURE  
SOUND  
OSD  
KEYSTONE AMPLITUDE ENTRYLIST  
R
G
B
MAGNIFY  
+
+
-
-
FOCUS  
CTL  
ZOOM  
LENS  
4. Adjust the image position and the image size.  
(1) Press and hold the CTL button and press the POSITION button to  
display the Lens Shift adjustment screen.  
Use the SELECT button on the remote control or the LENS SHIFT  
button on the projector cabinet to move the image horizontally and  
vertically.  
NOTE: If no input signal is available, the projector will display a blue background  
(factory preset).  
To close the Lens Shift adjustment screen, press the CANCEL  
button. See pages 2-4 and 2-5 for “Lens Shift Adjustable Range”.  
Using the menu  
You can also select the computer or video source using the menu.  
POSITION  
LENS  
POWER  
OFF  
ON  
MENU  
3D  
A
3D REFORM AUTO ADJUST  
S
ADDESS  
EN
CTL  
BS  
-
+
ON/STAND BY  
LAMP 2  
STATUS  
POWER  
-
3-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image  
(2) Press and hold the CTL and press the ZOOM + or - button to adjust  
the image size. You can also adjust the image size by using the  
ZOOM + or - button on the projector cabinet.  
Preparation (Recommended):  
Warm up the projector for about 60 minutes.  
Adjusting the Focus  
MAGNIFY  
1. Practice focusing  
+
+
Use the FOCUS (+) or (-) button on the projector or the remote control  
to increase or decrease the focus values to verify the accuracy of fo-  
cusing.  
-
2. Try optimizing defocus  
Use the FOCUS button (-) to decrease the focus values until pixel pat-  
terns are too blurry to be visible.  
FOCUS  
CTL  
ZOOM  
LENS  
3. Obtain correct focus  
Use the FOCUS button (+) to obtain the best focus. Do not use the  
FOCUS (-) button at this time.  
Finally store the adjustments in memory.  
If you adjust beyond the best focus point, go back to step 2 and repeat  
the procedures. Always adjust the focus from the negative direction  
towards the positive direction.  
v Correcting the Horizontal and Vertical  
Keystone Distortion (3D Reform)  
Use the 3D Reform feature to correct keystone (trapezoidal) distortion to  
make the top or bottom and the left or right side of the screen longer or  
shorter so that the projected image is rectangular.  
In the following description, 3D Reform (Cornerstone) correction can be  
done with the USB mouse, remote control or cabinet buttons.  
(3) Press and hold the CTL button and press the FOCUS + or - button  
to obtain the best focus.You can also adjust the focus by using the  
FOCUS + or - button on the projector cabinet.  
MAGNIFY  
+
+
When using the USB mouse connected to the projector  
Preparation: Connect the USB mouse to the projector. See page 4-3.  
-
1. Project an image so that the screen is smaller than the area of the  
raster.  
FOCUS  
CTL  
ZOOM  
LENS  
2. Pick up any one of the corners and align the corner of the screen with  
the one of the image. (The drawing shows the upper right corner.)  
Projected image  
Screen  
Tips on Adjusting Focus  
Optimum focus adjustments can be achieved on the projector by  
paying special attention in a few areas.  
Focus adjustment after the projector has warned up to normal  
operating temperature is better than doing so when the projector  
is cold.  
Lens mechanism interacts differently when adjusting focus from  
one direction to the other.  
For this reason final focus adjustments should be done in a spe-  
cific direction.  
For optimum focus, follow the steps below.  
For the zoom and the lens shift adjustment, perform the normal  
procedures.  
3-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image  
3. Press the 3D REFORM button on the remote control.  
The Cornerstone adjustment screen is displayed.  
The Cornerstone adjustment screen will disappear when you move the  
USB mouse cursor.  
When using the remote control or cabinet buttons:  
1. Project an image so that the screen is smaller than the area of the  
raster.  
2. Pick up any one of the corners and align the corner of the screen with  
the one of the image.  
4. Point to one of the remaining 3 corners and left-click on it.  
Left-click on the corner.  
Projected image  
Screen  
Screen  
(The drawing shows the upper right corner.)  
5. Do the above step 4 for the other two corners so that the projected area  
becomes smaller than the screen.  
3. Press the 3D REFORM button on the projector or the KEYSTONE but-  
ton on the remote control.  
Screen  
The Cornerstone adjustment screen is displayed.  
NOTE: Press the 3D REFORM button to toggle between "Cornerstone" and "Key-  
stone."  
Left-click on each corner.  
4. Use the SELECT ̆̄̇̈ button to select one icon which points in the  
direction you wish to move the projected image frame.  
6. To complete the procedure, right-click anywhere on the screen.  
The confirmation screen is displayed.  
7. Left-click on "OK".  
This completes the Cornerstone adjustment.  
*
To return the Cornerstone adjustment to the default settings, left-click  
on "Reset" in Step 7.  
You can save your Cornerstone changes. The changes are saved when  
you turn off the projector.To do so, select [Projector Options] → [Setup] →  
[Page 4]. Select the 3D Reform Save check box.This is not selected at the  
time of shipment.  
Screen  
* There are limitations of shapes which can be corrected using the Cor-  
nerstone adjustment.  
When adjusting the Cornerstone beyond these limits, you will get the mes-  
sage "Out of adjustment range!" and no correction can be done. Should  
this happen, do the Cornerstone adjustment again within the allowable  
range.  
* Due to limitations of accuracy within internal processes, there may be  
some discrepancy of positions between the mouse cursor and corrected  
shape or one corner and the other 3 corners.  
5. Press the ENTER button.  
6. Use the SELECT ̆̄̇̈ button to move the projected image frame as  
shown on the example.  
7. Press the ENTER button.  
Screen  
3-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image  
8. Use the SELECT ̆̄̇̈ button to select another icon which points in  
the direction.  
b Optimizing RGB Picture Automatically  
Adjusting the Image Using Auto Adjust  
Optimizing RGB image automatically  
Press the Auto Adjust button to optimize an RGB image automatically.  
[Poor picture]  
Screen  
3D  
A
3D REFORM AUTO DJUST  
SELECT  
ON/STAND BY  
LAMP 2  
STATUS  
POWER  
On the Cornerstone adjustment screen, select  
“Exit”and then“OK”, or press the CANCEL but-  
ton on the remote control.  
4
5
6
STU  
VWX  
YZ /  
The confirmation screen is displayed.  
9
7
8
[Normal picture]  
,.  
UNDO CANCEL  
0
TEST  
INFO.  
HELP  
AUTO  
POSITION PIXEL  
LENS  
9. Press the SELECT ̇ or ̈ button to highlight the [OK] and press the  
ENTER button.  
This completes the keystone correction.  
Selecting “Cancel” will return to the adjustment screen without saving  
changes (Step 3).  
Selecting "Reset" will return to the factory default.  
Selecting "Undo" will exit without saving changes.  
Press the AUTO ADJUST or AUTO button to fine-tune the computer im-  
age or to remove any vertical banding that might appear and to reduce  
video noise, dot interference or cross talk (this is evident when part of your  
image appears to be shimmering).This function adjusts the clock frequen-  
cies that eliminate the horizontal banding in the image. This function also  
adjusts the clock phase to reduce video noise, dot interference or cross  
talk. (This is evident when part of your image appears to be shimmering.)  
This adjustment may be necessary when you connect your computer for  
the first time.  
NOTE: To return the 3D Reform correction setting values to the factory default,  
press and hold the 3D REFORM button on the projector cabinet or the KEYSTONE  
button on the remote control for a minimum of 2 seconds.  
NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be avail-  
able. Should this happen, first reset the 3D Reform data and then do each setting.  
Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/or Screen  
setting can limit 3D Reform in its adjustable range.  
NOTE:  
• Some signals may not be displayed correctly or take time.  
• The Auto Adjust function does not work for component and video signal.  
• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock  
and Phase manually. See page 8-10.  
The adjustable ranges for 3D Reform are as follows:  
Horizontal ........... Max 30° approx.  
Vertical ............... Max 40° approx.  
n Turning Up or Down Volume  
Sound level from the speaker and the AUDIO OUT jack (RCA) on the  
projector can be adjusted.  
*
The following are conditions at the above maximum angle when all of  
the following are met  
•
•
Image is projected in Wide (Zoom)  
increase volume  
The lens is positioned at the center (when not, adjustable range in-  
creases or decreases)  
-
•
•
Resolution is XGA  
Higher resolution than XGA limits 3D Reform in its adjustable range.  
Menu items should be set as follows:  
decrease volume  
Aspect Ratio ............................... 4:3  
Screen Type ................................ 4:3  
Horizontal and Vertical are adjusted separately.  
NOTE: The SELECT ̆ or ̄ button works as a volume control only when no menu  
appears.  
•
•
A combination of both adjustments limits 3D Reform in its adjustable  
range.  
Volume bar  
NOTE: The volume bar can be dis-  
played by selecting “Sound” from “Ba-  
sic Menu” or “Advanced Menu”.  
When “Native” is selected in “Resolution”, “3D Reform” is not available.  
3-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image  
m Turning off the Projector  
To turn off the projector:  
First press the POWER (ON/STAND BY) button on the projector cabinet  
or the POWER OFF button on the remote control for a minimum of two  
seconds.The POWER indicator will glow orange. After the projector turns  
off, the cooling fans keep operating for 90 seconds (Cooling-off time).  
Second, turn off the Main Power switch. The power indicator will go out.  
Last unplug the power cable.  
POWER  
OFF  
ON  
MENU  
ADDRESS  
ENTER  
BS  
-
+
Fan working  
Power on  
Standby  
POWER  
POWER  
POWER  
ON/SAND BY  
Steady green  
light  
Flashing orange  
light  
Steady orange  
light  
NOTE: You cannot turn off the projector for 1 minute immediately after turning on  
the projector.  
CAUTION  
Do not unplug the power cable from the wall outlet or do not turn off  
the main power under any one of the following circumstances. Doing  
so can cause damage to the projector:  
•
While the Hour Glass icon appears.  
•
While the message "Please wait a moment." appears. This mes-  
sage will be displayed after the projector is turned off.  
•
•
While the cooling fans are running. (The cooling fans continue to  
work for 90 seconds after the projector is turned off).  
While accessing a PC card or LAN card. (The PC Card Access in-  
dicator lights.)  
3-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Convenient Features  
z Turning Off the Image and Sound.............................4-2  
x Enlarging and Moving a Picture................................4-2  
c Getting the On-line Help and Information .................4-2  
v Using a USB Mouse .................................................4-3  
b Using a USB HUB Function......................................4-3  
n Changing Background Logo .....................................4-4  
m Making Freehand Drawings on  
a Projected Image (ChalkBoard)..............................4-4  
, Lens Memory............................................................4-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
x Enlarging and Moving a Picture  
z Turning Off the Image and Sound  
Press the MUTE PICTURE button to turn off the image and sound for a  
short period of time. Press again to restore the image and sound.  
You can enlarge the area you want up to 400 percent.  
To do so:  
Press the MAGNIFY button.  
MUTE  
PICTUR
SOUND  
OSD  
Press the MUTE SOUND button to turn off the sound for a short period of  
time. Press again to restore the sound.  
Enlarge the selected area.  
When the MAGNIFY (+) button is pressed, the image is magnified. To  
move the magnified image, use the SELECT button.  
MUTE  
MAGNIFY  
PICTURE  
SOUND  
OSD  
+
Press the MUTE OSD button to turn off the on-screen display.Press again  
to restore the on-screen display.  
ZOOM  
Return the image to the original size.  
MUTE  
MAGNIFY  
PICTURE  
SOUND  
OSD  
+
-
NOTE: You can also turn off the on-screen display forcibly by pressing and holding  
CTL and then pressing MUTE OSD (Forced On-Screen Mute Mode) ; doing this  
again restores it. In this case any adjustment will still change the projector's memory  
settings. This mode is available even when input is switched to another or the main  
power is turned off.  
ZOO
c
Getting the On-line Help and Information  
You get the contents about Help.  
HELP  
SELECT  
Display Help  
Exit Help  
You get the source and projector information.  
INFO.  
Press this button once to display “Source Information” and press twice to  
display “Projector Information”.  
Press third time to close it.  
4-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
Operate the PC mouse using the USB mouse  
v Using the USB Mouse  
(
)
Using a commercially available USB mouse gives you smooth operation.  
USB PC  
2
)
USB(MSE/HUB USB(PC)  
PC CARD  
1
LAN  
PC
I
I
/
(
)
USB MOUSE/HUB  
REMOTE  
REMOTE  
1
I
2
1
O
SC
2
(
)
(
)
USB MOUSE/HUB USB PC  
PC CARD  
IN  
OUT  
LAN  
PC CONTROL  
IN  
I
AC IN  
/
R
REMOTE  
REMOTE  
1
2
OUT  
SC TRIGGER  
I
IN  
OUT  
AC IN  
R
NOTE: You can select the operation mode of the USB mouse connected to the USB  
port of the projector.  
NOTE: There may be some brands of USB mouse that the projector does not sup-  
port.  
Operate the Projector Menus using the USB mouse  
b Using the USB HUB Function  
Mouse Cursor  
When using the projector with a PC via the supplied USB cable, both the  
USB port(type A) on the projector can be connected to a USB-supported  
scanner or other USB-supported device. (USB Hub Function)  
When connecting a USB mouse to the projector, you get a  
mouse cursor on the screen.  
Unless you use your USB mouse within 10 seconds, the mouse  
cursor disappears.  
Example:When connecting a PC and a scanner to each USB port respec-  
tively  
Menu Display  
Clicking with a mouse button displays the menu.  
Clicking ̈ displays the pull-down menu. To close the menu,  
click anywhere in the background.  
(
)
USB MOUSE/HUB  
(
)
USB PC  
2
I
U
S
B
(
M
O
U
S
E
/
H
U
B
)
U
S
B
(
P
C
)
PC CARD  
1
LAN  
PC CO
IN  
I
C
/
REMOTE  
REMOTE  
1
OUT  
SC TRG
2
E
IN  
OUT  
A
C
I
N
R
Adjusting and Setting Display  
You can select a menu item and click with a mouse button to  
make adjustments and setting.  
Examples  
Click (or press and hold) the mouse button ̇ or ̈ to adjust  
the brightness. Or click and drag the mouse button on the slide  
bar horizontally to adjust it.  
An example of how a scanned image is projected  
1. Install the Dynamic Image Utility on your PC.  
To save the adjustments, click  
. This closes the menu. If you  
click anywhere in the background while displaying an adjust-  
ment and setting menu or dialog box, you will go to the main  
menu after clicking with the mouse.  
NOTE: The Dynamic Image Utility is contained on the supplied CD-ROM. See  
“6- b Software Installation” for the installation procedure.  
2. Use your scanner to scan an image.  
Clicking  
displays help.  
NOTE: A scanner driver must be installed on your PC before use.  
3. Load the scanned image on your PC using the Dynamic Image Utility.  
Using the Middle Button/Wheel on a Mouse (when avail-  
able)  
4. Transmit the scanned image from your PC to the projector via the USB  
cable and project the image on the screen.  
The projector supports the middle button/wheel on a mouse.With  
the middle button/wheel you can use a scroll bar or click the middle  
button/wheel to display or hide the Chalkboard toolbar.  
NOTE:  
•
The USB HUB function is effective only when “Auto” is selected in Operation  
Mode Select.  
•
•
The PCs using the USB Host Controller may not be available.  
When connecting a USB hub to the USB port (type B) on the projector, be sure  
to use a USB hub capable of supplying 500mA per port of downstream current.  
4-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
n Changing Background Logo  
m Making Freehand Drawings on a Projected  
Image (ChalkBoard)  
You can change the default background logo using the PC Card Files  
feature.  
The ChalkBoard feature allows you to write and draw messages on a pro-  
jected image.  
NOTE: File size must be 256KB or less. Other file formats than JPEG and BMP are  
not available.  
NOTE: The ChalkBoard feature is available only when a USB mouse is used.  
1. From the menu, select [Tools] → [PC Card Files] to display a list of all  
the files stored in the PC card so that you can select a file you want to  
use as a background logo.  
From the menu, select [Tools] → [ChalkBoard] to display the ChalkBoard  
tool bar that contains the following icons.  
NOTE: You can also display the ChalkBoard tool bar by clicking the scroll button on  
your USB mouse.  
Eraser  
Drive  
Pen  
Exit  
Color  
Clear  
Hide  
Capture  
Pen .............. Left-click and drag to draw. Left-click [̆] or right-click the  
pen icon to display the pen palette containing four lines of  
different thickness from which you can select a line you pre-  
fer by left-clicking.  
Color ........... Selects a color. Left-click to display the color palette from  
which you can select a color you prefer by left-clicking.  
Capture ....... Left click to capture and save freehand drawings in the PC  
card.  
2. The Logo button allows you to select a background logo from graphic  
files on a PC card and change to it as the background logo.  
3. Use the SELECT ̆ or ̄ button to select a JPEG or BMP file for your  
background logo.  
Eraser ......... Left-click and drag to erase part of a drawing. Left-click [̆]  
or right-click the eraser icon to display the eraser palette  
containing four eraser of different thickness from which you  
can select an eraser you prefer by left-clicking.  
Clear ........... Left-click to clear the drawing completely from the  
ChalkBoard screen.  
4. Use the SELECT ̈ and then ̄ button to select "Logo".  
5. Press the ENTER button on the remote control or the cabinet. You  
will get the confirmation dialog box.  
6. Select "OK" and press the ENTER button. This completes changing  
a logo for the background.  
Drive ............ Switches between PC Card slot.  
Hide ............. Hides the tool bar by left-clicking. Right-clicking anywhere  
on the screen displays the ChalkBoard tool bar again.  
Exit .............. Clears the complete drawing and exits the ChalkBoard.  
NOTE:  
• The menu is not available while you display the ChalkBoard screen.  
• Switching slides clears a drawing completely.  
*
Once you have changed the background from the NEC logo to an-  
other, you cannot return the logo to background even by using Fac-  
tory Default. To do so, repeat the above steps. The NEC logo file is  
included on the supplied CD-ROM NEC Projector User Supportware  
(/Logo/nec_bb_x.jpg).  
4-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
, Lens Memory  
This function serves to store the adjusted value when using the Shift,  
Focus, and Zoom buttons of the projector or the remote control.  
Reference memory:  
Reference Point ....... Adjusted settings are stored in memory as a  
reference common to all the input sources. If  
no setting is stored in Custom Point, the ad-  
justed settings in Reference Point will be ap-  
plied.  
Custom memory:  
Custom Point ........... Adjusted settings are stored in memory for  
each input signal.  
Usage Example  
When you wish to display on a screen having a 4:3 aspect ratio an  
NTSC or other 4:3 aspect ratio signal and an SXGA or other 5:4 as-  
pect ratio signal:  
Perform shift, focus, and zoom adjustments to set the vertical screen  
size of the vertically tall 5:4 aspect ratio signal to standard.  
Both 4:3 apsect ratio signals and 5:4 aspect ratio signals can now be  
displayed.  
Note that with these shift, focus, and zoom adjustments, the 4:3 aspect  
ratio signal will become smaller on the screen.  
To eliminate this size reduction, adjust the shift, focus and zoom to the  
optimum condition for each of the 4:3 aspect ratio signal and the 5:4  
aspect ratio signal. Memory (storage) of each of these values will per-  
mit projection at an optimum condition upon signal switching.  
1. Perform Zoom, Focus and Lens Shift adjustments and store them  
in memory using “Set Custom Point”.  
Another way to store your adjustments is to use the CTL and INFO  
buttons on the remote control.  
2. When “Yes” is selected for “Use Point on Signal Change”, the ad-  
justment is applied to the signal you switched.  
NOTE: The Lens Memory function is not available in Link mode.  
NOTE: The other optional lenses than GT10RLB, GT13ZLB, GT20ZL, GT24ZLB and GT34ZLB  
do not support Lens Memory function. (On GT10RLB focus can be stored in memory)  
You cannot store settings for zoom and focus on the following lenses:  
GT13ZL, GT19ZL, GT24ZL and GT34ZL.  
Picture Mute during Lens Shift?  
To turn off the image and sound during lens shift, select "Yes".  
NOTE: This option is only available when "Yes" is selected for "Use Point on Signal Change?".  
4-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Using the Viewer  
z Making the Most out of the Viewer Function.............5-2  
x Operating the Viewer Function from the Projector  
(playback).................................................................5-3  
5-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using the Viewer  
Inserting and Removing a PC Card  
NOTE:  
•
To use the Viewer, first you need to create presentation materials on your PC  
NOTE:  
Do not try to force the PC card into the slot.  
using the Dynamic Image Utility 2.0 contained on the supplied NEC Projector  
User Supportware CD-ROM. For installation, see “6- b Software Installation”.  
For creating presentation materials, see the Slide show function on the on-line  
manual of the Dynamic Image Utility 2.0.  
•
2
•
Selecting Viewer sets the audio input for DVI input.  
PC CARD  
1
z
Making the Most out of the Viewer Function  
NOTE: When using two PC cards, do not insert both PC cards into the two PC card  
slots simultaneously. Doing so may cause projector malfunction such as shutting  
down. Each PC card must be inserted slowly one at a time.  
Features  
You can view presentation data, capture, and play images on the  
projector. A PC card is used to view presentation data prepared  
on the computer and to capture and play images projected with  
the projector.  
The Viewer feature allows you to view slides stored on a PC  
memory card (referred to as PC card in this manual) on the pro-  
jector. Even if no computer is available, presentations can be  
conducted simply with the projector. This feature is convenient  
for holding presentations at meetings and in offices, as well as  
for playing images taken on digital cameras.  
Inserting the PC Card  
•
Hold the PC card horizontally and insert it slowly into PC card slot  
1 or 2 with its top facing up.  
PC card (not supplied)  
USB  
(
MOUSE/HUB  
)
USB  
(
2
1
PC  
)
PC CARD  
PC CONTROL  
Easy to use  
LAN  
•
Presentations can be started immediately simply by inserting a  
PC card (not supplied)  
T  
SC TRIGGER  
REMOTE  
REMOTE  
1
2
•
•
•
Easy slide switching  
IN  
Remote control operation  
OUT  
AC IN  
Jumping to list of slides or any specific slide  
Removing the PC Card  
High quality images  
Press the eject button slowly.The eject button card pops out a  
little. Press the eject button slowly again. Grasp the edges of  
the PC card and pull it out. Push and insert the eject button  
fully until it stops.  
•
•
•
High resolution up to 1024 x 768 dots  
24-bit full color playback  
Viewing of digital camera images  
Simple utility software (for computer)  
•
•
•
*
Dynamic Image Utility 2.0 operable on Windows 98/Me/XP/2000  
Slides can be created by capturing the currently displayed image  
Control screen for displaying lists of slides and editing  
U
SB  
(
M
O
U
S
E
/H  
U
B
)
U
S
B
(
2
Eject button  
P
)
P
C
C
O
O
L
Microsoft, Windows and PowerPoint are registered trademarks of  
Microsoft Corporation.  
R
M  
EM  
O
TE  
TE  
1
2
O
IN  
O
U
T
A
C
IN  
NOTE: Do not eject the PC card while its data is being accessed.  
Direction for Inserting the PC Card  
The PC card has a top and bottom and must be inserted into  
the PC card slot in a specific direction. It cannot be inserted  
backwards or upside-down. Attempting to force it into the slot  
in the wrong direction may break the internal pin and damage  
the card slot. Refer to the PC card's operating instructions for  
the proper direction of insertion.  
PC Card Type  
The PC Card slot accepts PCMCIA Type II only.  
5-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using the Viewer  
When the tool bar is not displayed:  
x Operating the Viewer Function from the  
Projector (playback)  
You can use the ̇ and ̈ button on the cabinet to select folders  
or slides.  
This section describes the operation for showing slides of pre-  
sentation documents created using the Viewer function with the  
projector. It is also possible to make slides directly from the im-  
ages projected with the projector.  
3D  
A
3D REFORM AUTO ADJUST  
SELECT  
ON/STAND BY  
Projecting slides (Viewer)  
1. Insert a PC card into the PC card slot.  
LAMP 2  
STATUS  
POWER  
Insert the PC card so that the end with the insertion direction arrow on  
the top goes in first.  
*
Press the eject button to eject the card.  
Multi cursor (blue marks)  
2. Select the "Viewer" from the Source Select menu.  
3. Project slides.  
Folder  
Folder  
Folder  
Folder  
Folder  
Checking "Show Folder List", means that selecting Viewer input  
displays a list of the folders in the PC card and if "Auto Play" is  
checked the projector automatically starts to play slides at the  
first slide of the folder you have selected.  
02 : 0001 / 0008  
Current folder number  
A tool bar will appear when you press the MENU button on the  
remote control or the projector cabinet or clicking with the right  
button of a mouse.  
Number of all slides in folder  
Current slide  
number  
Delete  
Prev  
Play  
Jump  
Drive  
Use the SELECT ̇ or ̈ button to advance to the next folder  
or return to the previous folder.  
View  
Setup  
Next  
Stop  
Select  
N
3D  
3D REFORM  
SELECT  
The tool bar includes the following buttons:  
Folder  
T
ON/STAND BY  
Prev .......... Returns to the previous slide or folder. Or this lets  
you play slides back in reverse.  
LAMP 2  
STATUS  
POWER  
Next .......... Advances to the next slide or folder. Or this lets you  
play slides back.  
Play .......... Plays back automatically or manually depending on  
the setting on Viewer Options of the menu. This al-  
lows you to move on to the next slide when "Manual  
Play" is selected.  
Use the SELECT ̇ or ̈ button to advance to the next slide or  
return to the previous slide.  
Stop .......... This allows you to stop Auto Play while you are play-  
ing back and to resume playing from the selected  
slide or folder when "Auto Play" is selected.  
Slide(Table) cursor  
(green marks)  
Slide  
Slide  
Slide  
Slide  
Slide  
Slide  
Slide  
Slide  
Jump ........ Displays a list of slides while you are playing back.  
Select ....... Displays a list of folders while you are playing back.  
Drive ......... Switches between PC Card slot.  
Setup ........ Displays the Viewer Options dialog box on Page 2 of  
the Setup dialog box.  
02 : 0004 / 0008  
Delete ....... Deletes a captured slide(s) or all the captured slides  
in the Capture - specific folder.  
View ......... Hides the tool bar while you are playing back. Press-  
ing the MENU button or clicking with the right button  
of a mouse shows it again.  
NOTE: If no memory card is inserted in the PC CARD slot, there is no signal, and a  
black, blue or logo background is displayed, depending on the setting.  
Playback is stopped when ̇̈ button on the cabinet is pressed in Auto Play mode.  
Up to 12 indexes can be displayed on the list of folders. The folder in the right  
bottom is always a folder exclusively for captured images, but is only displayed  
when images have been captured.  
5-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using the Viewer  
Auto Play Mode  
Preparations:  
Insert the PC card into the card slot.  
Insert the PC card so that the end with the insertion direction  
arrow on the top goes in first.  
If the "Auto Play" option is selected in "Viewer Options" of the  
menu, any given slide will start to play automatically.  
You can also specify Auto Play Interval between 5 and 300 sec-  
onds.  
* Press the eject button to eject the card.  
1. Project the image you wish to store on the projector.  
Switching to Slides Directly from Other Input Modes  
With this function it is possible to switch directly to a slide when  
the picture of a VCR or computer is being projected.  
Example: When conducting presentations using a combination  
of slides and moving pictures from a VCR, etc., it is possible to  
switch from a Viewer slide to the video picture then back to the  
Viewer slide simply by using the SELECT button.  
NOTE: Even if you switch the current Viewer source to another source, the current  
slide is retained. When you return back to the Viewer, you will get the slide that has  
been retained.  
2. Select the "Capture" from the Tools menu.  
3. A tool bar will appear.  
Capture  
Freeze  
The PC card editing operation cannot be performed from the pro-  
jector. Do so using the Dynamic Image Utility 2.0 software.  
Exit  
Viewing Digital Images  
Drive  
Digital images can be played with the Viewer if the following con-  
ditions are met:  
The tool bar includes the following buttons:  
•
•
If the image can be stored on an MS-DOS format PC card  
Capture .... Captures an image and save it as a JPEG file on a  
PC card.  
If the image can be stored in a format supported by the Viewer.With the  
Viewer, images on the card are searched for in directories and images  
in JPEG or BMP format are recognized as slides. Searchable directo-  
ries are directories within two steps from the root directory, and search-  
able images are images within the first 12 files in the directory. Only file  
and slide switching are possible.  
Freeze ...... Freezes and unfreezes images.  
Drive ......... Switches between PC Card slot.  
Exit ........... Exits the Capture function. Another option to exit the  
Capture function is to press MENU or CANCEL but-  
ton on the remote control or projector cabinet.  
NOTE: The maximum number of images recognized as slides within one directory  
is 128.  
NOTE:  
You can compress a captured file (JPEG) using the Capture Options in the Setup  
dialog. See page 8-15.  
Storing Images Displayed on the Projector on the PC card  
(Capture)  
Captured images with higher resolution than the projector's native resolution can-  
not be displayed correctly.  
The Capture features allows you to capture an image from a  
source that is currently being displayed. The image is saved as  
JPEG in the PC card. When you select Capture from the menu,  
you will get a tool bar. You can capture an image directly using  
the tool bar when the menu is not displayed.  
• File size of the captured image varies depending on the resolution of an input  
signal.  
• An hourglass indicating that an image is being captured appears on the projector's  
display. Do not eject the PC card or turn off the projector's power while this icon  
is displayed. Doing so will damage the PC card data. If the PC card data is dam-  
aged, use a computer to repair the data.  
NOTE:  
* Unless a PC card is inserted into the PC Card slot of the projector, the Capture  
feature is not available.  
* The "Card Error" display means that the free space of the PC card is insufficient  
for saving images. Make more space available on the card by erasing unwanted  
images with your PC. The number of images that can be captured depends on  
the size of the PC card.  
5-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using the Viewer  
Deleting Captured Images  
Using the Delete button on the tool bar for Viewer can delete  
captured images.  
Delete  
Prev  
Play  
Jump  
Drive  
View  
Setup  
Next  
Stop  
Select  
To delete captured images:  
1. Select Viewer and display a folder list of captured images.  
2. Use button to select the Capture folder “Cap” in the right bottom of  
the screen.  
3. Press the MENU button to display the tool bar.  
4. Use the ̇ or ̈ button to select the Delete icon and press the ENTER  
button or click with a mouse button.  
Using the PC Card Files Fucntion (PC Card Files)  
The PC Card Files function allows you to display a list of all the  
files stored in the PC card so that you can select a file you want  
to display.You can also sort files by file name or date, or display  
the file. Although a list of all the files in the PC card is displayed,  
you can view files in idx, text, HTML, JPEG and BMP format only.  
Selecting BMP and JPEG files automatically switches to the  
Viewer source. See also page 5-3.  
NOTE: This option is not available for selection unless a PC card is inserted prop-  
erly.  
Selecting "Execute" displays the file you selected.  
When you select a JPEG or BMP file and press the ENTER but-  
ton on the remote or the cabinet, or "Execute" on the above, you  
will get a toolbar. This toolbar is used to return to the PC Card  
Files screen.  
Close  
Return  
Return ......... Returns to the PC Card Files screen.  
Close ...........Close the toolbar.  
5-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Using the Projector in a Network  
z End User License Agreement...................................6-2  
x Introduction ...............................................................6-3  
c Supported Projectors................................................6-4  
v Equipment Connections and Settings ......................6-5  
b Software Installation .................................................6-6  
n Starting/Exiting the Software ....................................6-7  
m Troubleshooting ........................................................6-8  
6-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Using the Projector in a Network  
Be sure to read this before using the accompanying software.  
6. Limitations of Warranty  
1) Except as expressly specified herein, the Software is provided "as  
is" without warranty of any kind, including but not limited to implied  
warranties for fitness for a particular purpose, merchantability, title  
and non-infringement of any third party rights.  
z END USER LICENSE AGREEMENT  
PLEASE READTHIS SOFTWARE LICENSE AGREEMENT ("LI-  
CENSE") CAREFULLY BEFORE PRESSING THE "Yes" BUT-  
TON BELOW. BY PRESSING "Yes", YOU ARE AGREEING TO  
BE BOUND BY THE TERMS OF THIS LICENSE. IF YOU DO  
NOT AGREE TO THE TERMS OF THIS LICENSE, PRESS "No"  
AND (IF APPLICABLE) RETURN THIS SOFTWARE TO THE  
PLACE WHERE YOU OBTAINED IT FOR A REFUND.  
2) If User finds a material defect, which effects to the proper opera-  
tion of the Software, in the media of the Software, NECVT will re-  
place such defective media at no charge, if such media is returned  
to distributor from which such User purchased it within 1 month  
from such purchase and if NECVT determines that such defect is  
due to NECVT.  
NECViewtechnology,Ltd.("NECVT") grants you ("User") a license  
to use the NEC PROJECTOR USER SUPPORTWARE ("Soft-  
ware") provided with this End User License Agreement ("EULA").  
User assumes responsibility for the selection, adoption use and  
the result of use of the Software to achieve its intended result.  
7. Limitations of Liability  
In no event shall NECVT be responsible for any indirect, conse-  
quential or special damages or lost profits even if NECVT has  
been advised of the possibility of such damages, and/or for any  
claim for compensation or damage by any third party to User.  
1.Term  
8. Others  
1) EULA will become effective upon User's agreement to the terms of  
EULA and shall remain in force until User terminates it by return-  
ing or destroying the Software and its related documents.  
1) The validity, interpretation, construction and performance of EULA  
shall be governed by the laws of Japan.  
2) User shall not export the Software to any country to which such  
export would be prohibited by any applicable laws.  
2) Notwithstanding the foregoing NECVT may terminate EULA at any  
time upon User failing to abide by any terms of EULA. Upon the  
termination of the EULA by NECVT, the license granted to User  
shall be terminated automatically. User agrees to destroy the Soft-  
ware together with all copies of it upon such termination.  
2. License  
User use the Software on personal computers only for operating  
NECVT's projector supplied with the Software or other projector  
to be specified by NECVT("Projector")  
3. Replication, modification and merger of the Software  
1) User may make copies of the Software and related documentation  
to the extent necessary for using the Projector. User agrees to  
reproduce the NECVT's copyright notice and other notice on any  
such copies.  
2) User may not use, copy, modify, or otherwise dispose of the Soft-  
ware, except as expressly permitted in EULA.  
3) No provision in EULA shall be construed to assign and/or transfer  
any intellectual property right in the Software to User.  
4.Transfer of the Software  
1) User may transfer the Software to any third party, provided always  
that:  
a) User must transfer, with the Software, to such third party EULA  
and all the related  
documentation with all copies thereof, and must not retain any  
copy thereof.  
b) Such third party has agreed to the terms and conditions of  
EULA.  
2) Except as otherwise expressly permitted above, User may not sub-  
license, assign, transfer or otherwise dispose of the license for the  
Software.  
5. Reverse Engineering  
User may not reverse engineer, decompile, and/or disassemble  
the Software, except and only to the extent that such activity is  
expressly permitted by applicable law notwithstanding this limi-  
tation.  
6-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Using the Projector in a Network  
*1: Please purchase a commercially available PCMCIA Type 2 (ATA  
specification) flash memory card.  
x Introduction  
Thank you for your purchase of the NEC portable projector (here-  
after referred to as "unit" or "projector").  
*2: Please check the network environment on the next page.  
*3: USB cable connection is supported by the MT1065, MT1060,  
MT860 and GT5000 only.  
This projector is connected to a personal computer or other equip-  
ment and clearly projects text or graphics to a screen.  
This projector is supplied with convenient software that allows  
presentations to be made more simply and effectively.This guide  
gives an overview and describes the use of the accompanying  
software (contained in the CD-ROM that is supplied with this pro-  
jector). Look over this guide in conjunction with the Help func-  
tions of the software programs.  
Information about Upgrading this Software  
Please see the service page for NEC projectors (http://www.nec-  
pj.com/) for information about software upgrades of NEC Projec-  
tor User Supportware (i.e., Dynamic Image Utility, Viewer PPT  
Converter, and Image Express Utility).  
Projector "Easy Connection" Settings  
Contents of the Supplied CD-ROM  
The supplied CD-ROM contains the following software programs:  
Software that can abbreviate the troublesome LAN settings that  
are used when connecting the PC and projector via a wireless  
LAN can be downloaded from our website at no charge. After  
you have installed the software from the supplied CD-ROM to  
your PC, visit our website to update the information.  
• Dynamic Image Utility 2.0  
• Viewer PPT Converter 2.0  
• Image Express Utility 1.0  
Please see the Help functions of the software programs for infor-  
mation about their functions and operation.  
•
From the Advanced menu, select [Projector Options] → [LAN Mode] →  
[Status] → [Advanced] → [Network Type] → [Mode] → [Easy Connec-  
tion] on the projector. (No setting for IP address and channel are re-  
quired.)  
What Can Be Accomplished with the Supplied Software  
•
Before executing Easy Connection using Image Express Utility, visit  
our website to check the information.  
Dynamic Image Utility 2.0  
•
•
Easy Connection is available on Windows 2000 and XP.  
•
Converts PowerPoint files, JPEG images, and other files and cre-  
ates slides that can be displayed with the viewer function of the  
projector.  
Easy Connection is available only when both PC and projector use the  
NEC optional wireless cards.  
• Captures portions of the image from the screens of word processors,  
spreadsheets, browsers, and other programs for use in presenta-  
tions.  
•
Easy Connection is not available on Dynamic Image Utility included on  
the supplied CD-ROM.  
•
By saving the created slides on a flash memory card (*1) and in-  
serting the card into the PC Card slot of the projector, the slides  
can be projected to the screen without connecting a personal com-  
puter.  
•
The connection of personal computers and projectors by means of  
a network environment (*2) or connection with USB cable (*3) or  
serial cable allows the following uses. (In a network environment  
or USB cable connection (*3) , support of multiple units is permit-  
ted.)  
(1) Images and slides can be sent from the personal computer to the  
projector and then projected to the screen. When using Microsoft  
PowerPoint 2000/2002, slides can be sent synchronized with the  
slide show page feed.  
(2) A personal computer can be used to switch the projector power  
on/off, control the adjustment of image quality and other settings,  
and to display the remaining lamp life.  
Viewer PPT Converter 2.0  
•
Converts files created with Microsoft PowerPoint 95/97/2000/2002  
to an independent index format with a simple operation to enable  
direct playback with the viewer function of the projector.  
•
When using Microsoft PowerPoint 2000/2002, Viewer PPT Con-  
verter 2.0 can be started from PowerPoint (by means of add-in  
registration to PowerPoint).  
Image Express Utility 1.0  
•
Using a network environment (*2), this program enables the screen  
image displayed by the personal computer to be sent to the projec-  
tor and then projected to a screen.  
•
Two methods are available for sending the screen image to the  
projector. "Continuous Transmit" automatically sends the screen  
image of the personal computer at a fixed interval. "Single Frame  
Transmit" sends the screen image by clicking the screen button (or  
pressing a key).  
6-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Using the Projector in a Network  
c Supported Projectors  
The following NEC projectors will be supported:  
GT5000, MT1065/MT1060/MT860, LT260/LT240/LT220  
Operating Environment  
Supported Equipment  
IBM PC/AT compatible computers  
• CD-ROM drive a requirement (at time of installation)  
Pentium MMX processor or higher a requirement  
Pentium III 800 MHz or higher recommended  
For Windows XP  
CPU  
Memory  
• 128 MB or more a requirement  
• 192 MB or more recommended  
For other operating systems  
• 64 MB or more a requirement  
• 128 MB or more recommended  
t More memory may be necessary when other applications are run at the same time.  
A LAN that supports TCP/IP or a wireless LAN environment is a requirement.  
• For information on supported LAN cards, visit:  
http://www.nec-pj.com/ (In US: http://www.necvisualsystems.com)  
• For wireless LAN connection, use NEC optional wireless LAN card (SWL-2100N-N*).  
* Last digit of the model code varies depending on which country you live in. For more information,  
visit the above Website.  
Network Environment  
(when used)  
Supported OS  
Windows 98  
Windows 98 SecondEdition  
Windows Me  
Windows 2000 Professional  
Windows XP HomeEdition  
Windows XP Professional  
* Microsoft Internet Explorer 5.01 or higher is required for the aforementioned environments.  
* Does not support Windows power-saving function.  
1024 dots x 768 lines recommended  
Resolution  
( 800 dots x 600 lines recommended for LT220 and MT860)  
High Color (15 bit, 16 bit)  
Screen Colors  
True Color (24 bit, 32 bit)  
6-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Using the Projector in a Network  
[For Connections with USB Cable]  
Equipment to Be Prepared  
v Equipment Connections and Settings  
When Using a Network Environment  
•
•
•
Projector (This unit)  
Personal computer  
What Can Be Accomplished  
•
Using Image Express Utility 1.0, the screen image displayed by the  
personal computer can be sent to the projector and then projected to a  
screen.  
USB cable (included with the projector)  
Connection at the Projector Side  
Plug the B type connector of the USB cable to the USB port [PC]  
(type B).  
•
•
Using Dynamic Image Utility 2.0, a picture or slide can be sent to the  
projector and then projected to a screen.  
Using the projector control function of Dynamic Image Utility 2.0 allows  
operations to be performed from the personal computer which include  
switching the projector power on/off, signal selection, and adjustment  
of the picture quality.  
NOTE: When switching the power of the projector on/off with the projector control  
function, please set [Projector Options] → [Setup] → [Page 4] → [Idle Mode] to  
“On”.  
Equipment to Be Prepared  
Connection at the Personal Computer Side  
Plug the A type connector of the USB cable to the USB port [PC]  
(type A).  
• Projector (This unit) • Personal computer (with LAN card)  
• LAN cable (not supplied) or wireless LAN card (optional)  
[For Connections with Serial Cable]  
Settings at the Projector Side  
Preparation:  
Equipment to Be Prepared  
(1) Connect a LAN cable (not supplied) to the LAN port (RJ-45) of the  
projector.  
•
•
•
Projector (This unit)  
Personal computer  
(For the use of an optional wireless LAN card, insert the wireless LAN  
card into the PC CARD slot 1 or 2 of the projector.)  
Serial cable (Optional CA03D for LT260/LT240/LT220 and a commer-  
cially available RS-232C cross cable for MT1065/MT1060/MT860/  
GT5000)  
(2) Switch on the projector power and project to the screen. (chapter 3)  
(3) Switch to the advanced menu.  
1. Press the MENU button.  
The menu will be displayed.  
Connection at the Projector Side  
Plug the serial cable into the PC CONTROL connector. (“Termi-  
nal Panel Features” and “PC Control Connector” on pages 1-9  
and 10-10)  
2. Use the SELECT ̄ button to align the cursor with [Projector Options],  
then press the ENTER button.  
The sub menu will be displayed.  
Connection at the Personal Computer Side  
Plug the serial cable into the (RS-232C) serial connector.  
3. Use the SELECT ̄ button to align the cursor with [LAN Mode], then  
press the ENTER button.  
The LAN mode setting screen will be displayed.  
4. Set the various items.  
See "Setting LAN Mode" on page 8-19 for information about the vari-  
ous items.  
NOTE: When switching the power of the projector on/off with the projector control  
function, please set [Projector Options] → [Setup] → [Page 4] → [Idle Mode] to  
"On".  
Settings at the Personal Computer Side  
Perform the regular LAN connections settings according to the  
instruction manual of the LAN card (adapter).  
There are no special settings to be made in the connections with  
the projector.  
When Making Connections with Serial Cable or USB  
Cable(*)  
*
USB cable connection is supported by the MT1065, MT1060, MT860  
and GT5000 only.  
What Can Be Accomplished  
• Using Dynamic Image Utility 2.0, a picture or slide can be sent to the  
projector and then projected to a screen.  
• Using the projector control function of Dynamic Image Utility 2.0 allows  
operations to be performed from the personal computer which include  
switching the projector power on/off, signal selection, and adjustment  
of the picture quality.  
6-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Using the Projector in a Network  
7. Now, follow the operations described in the screen messages.  
When the uninstall procedure is completed, there will be a return to the  
"Add/Remove Programs Properties" screen.  
b Software Installation  
NOTE  
• Windows 98 operations will be described in examples given here.  
8. Click [OK].  
There will be a return to the "Control Panel" screen  
• When using Windows 2000, please perform software installation/uninstalling with  
"Administrators" authority. When using Windows XP, perform with "Computer  
Administrator" authority.  
Installation  
Dynamic Image Utility 2.0, Viewer PPT Converter 2.0, and Im-  
age Express Utility 1.0 will all be installed together. The various  
programs cannot be installed individually.  
Preparation:  
Start Windows.  
If Windows has already been started, please exit all running ap-  
plication software. The installation may not be completed prop-  
erly unless all software has been exited.  
1. Place the supplied CD-ROM in the CD-ROM drive.  
The "Welcome" screen will appear.  
Reference  
Should the "Welcome" screen not appear...  
1) Click [Start].  
2) Click [Run (R)]. The [Run] screen will appear.  
3) Enter the CD-ROM drive name (e.g., "Q:\") and then "SETUP.EXE"  
to [Open (O)].  
4) Click [OK]. The "Welcome" screen will appear.  
2. Click [Next >] at the "Welcome" screen.  
The "End User License Agreement" screen will appear.  
•
Please carefully read the contents of the "End User License Agree-  
ment".  
3. If you agree, click [Yes].  
•
If you do not agree, please click [No] and exit the installer.  
4. Now, follow the operations described in the screen messages.  
•
Please remove the CD-ROM from the CD-ROM drive when the  
installation is completed.  
Reference  
•
To cancel the installation of the supplied software part way through  
the installation, click [Cancel] and follow the instructions of the dia-  
log box.  
Uninstalling  
Dynamic Image Utility 2.0, Viewer PPT Converter 2.0, and Im-  
age Express Utility 1.0 will all be uninstalled together. The vari-  
ous programs cannot be uninstalled individually.  
1. Click [Start].  
2. Click [Settings] R [Control Panel].  
The "Control Panel" screen will be displayed.  
3. Double click [Add/Remove Programs].  
The "Add/Remove Programs Properties" screen will appear.  
4. Click "NEC Projector User Supportware" from the list.  
5. Click [Add/Remove. . . ].  
The "Confirm File Deletion" screen will appear.  
6. Check the message and click [Yes].  
6-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Using the Projector in a Network  
Exit the Software  
1. Click [Exit].  
n Starting/Exiting the Software  
Viewer PPT Converter 2.0 will close.  
Dynamic Image Utility 2.0  
Start the Software  
Preparation:  
Install the software on the personal computer from the supplied  
CD-ROM. (Page 6-6)  
The software cannot be started from the supplied CD-ROM.  
Image Express Utility 1.0  
Start the Software  
Preparation:  
Install the software on the personal computer from the supplied  
CD-ROM. (Page 6-6)  
The software cannot be started from the supplied CD-ROM.  
From the [Start] menu click [Program] → [NEC Projector User  
Supportware] → [Dynamic Image Utility 2.0].  
Dynamic Image Utility 2.0 will start.  
1. From the [Start] menu click [Program] → [NEC Projector User  
Supportware] → [Image Express Utility 1.0].  
Image Express Utility 1.0 will start.  
Reference  
Reference  
•
By selecting a PowerPoint file with Dynamic Image Utility 2.0 and click-  
ing [Tools] → [Converting PowerPoint file], the function equivalent to  
Viewer PPT Converter 2.0 can be executed.  
•
Image Express Utility 1.0 can also be started from the [Tools] R  
[Image Express Utility 1.0 Start] menu of Dynamic Image Utility  
2.0.  
•
Image Express Utility 1.0 can be started by clicking [Tools] → [Image  
Express Utility 1.0 Start] of Dynamic Image Utility 2.0.  
Display Help  
Preparation:  
Please start Image Express Utility 1.0.  
Display Help  
Preparation:  
Please start Dynamic Image Utility 2.0.  
1. Click the [ ] or [ ] icon of the Windows screen task tray.  
The main menu of Image Express Utility 1.0 will appear.  
1. Click [Help].  
The [Help] menu will appear.  
2. Click [Help] .  
The Help screen will appear.  
2. Click [Help].  
The [Help] screen will appear.  
Exit the Software  
1. Click the [ ] or [ ] icon of the Windows screen task tray.  
The main menu of Image Express Utility 1.0 will appear.  
Exit the Software  
1. Click [File].  
The [File] menu will appear.  
2. Click [Exit].  
Image Express Utility 1.0 will close.  
2. Click [Exit].  
Dynamic Image Utility 2.0 will close.  
Viewer PPT Converter 2.0  
Start the Software  
Preparation:  
(1) Check that Microsoft PowerPoint has been installed.Viewer PPT Con-  
verter 2.0 cannot be used unless PowerPoint has been installed.  
(2) Install the software on the personal computer from the supplied CD-  
ROM. (Page 6-6)  
The software cannot be started from the supplied CD-ROM.  
1. From the [Start] menu click [Program] → [NEC Projector User  
Supportware] → [Viewer PPT Converter 2.0].  
Dynamic Image Utility 2.0 will start.  
Reference  
•
A function equivalent to Viewer PPT Converter 2.0 can also be  
executed from the Dynamic Image Utility 2.0 [Tools] → [Converting  
PowerPoint file] menu.  
•
Viewer PPT Converter 2.0 can also be started from the Microsoft  
PowerPoint 2000/2002 [Tools] → [NEC Projector User Supportware]  
→ [Output Viewer] menu.  
Display Help  
Preparation:  
Please start Viewer PPT Converter 2.0.  
1. Click [Help].  
The [Help] menu will appear.  
6-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Using the Projector in a Network  
m Troubleshooting  
In this section, the software names have been abbreviated as follows:  
Dynamic Image Utility 2.0 to DIU 2.0, Viewer PPT Converter 2.0 to PPTC 2.0, and Image Express Utility 1.0 to IEU 1.0.  
<Problem> Installation does not complete normally.  
Check Points  
Countermeasures  
When using Windows 2000, did you log on with "Administra-  
tors" authority? When using Windows XP, did you log on with  
"Computer Administrator" authority?  
When using Windows 2000 or Windows XP, log on with the  
authority described at the left and then install.  
Has Microsoft PowerPoint 2000/2002 been installed on the  
personal computer to which this projector software is being  
installed?  
When this projector software is installed on a personal  
computer that does not have PowerPoint 2000/2002 installed,  
a message to the effect of "Error in the automatic registration of  
PPTViewer2.dll" will appear part way through the installation.  
When the message described at the left appears part way  
through the installation, add-in registration will not be made to  
PowerPoint; however, the installation of this projector software  
will be completed normally.  
To have add-in registration made to PowerPoint, please install  
this projector software to a personal computer on which  
PowerPoint 2000/2002 has been installed.  
<Problem> Viewer PPT Converter 2.0 does not function. (PPTC 2.0)  
Check Points  
Countermeasures  
Has Microsoft PowerPoint been installed on the personal  
computer?  
Install PowerPoint on the personal computer. Or, install Viewer  
PPT Converter 2.0 on a personal computer on which  
PowerPoint has been installed.  
<Problem> When using the projector control function, the projector power does not switch on. (DIU 2.0)  
Countermeasures  
Check Points  
Are the personal computer and the projector connected by a  
serial cable?  
Connect the personal computer and the projector with an serial  
cable or USB cable.  
Or, are the personal computer and the projector connected by  
a LAN?  
Or, check the LAN port (RJ-45) of the projector. Purchase the  
optional wireless LAN card for wireless LAN connection.  
When the personal computer and the projector are connected  
with a LAN, is the projector in the idle mode?  
In the [Projector Options]Ǟ[Setup] menu of the projector, place  
checkmark in “Idle Mode”. Connect a power cable to the  
power outlet and set the main power switch to "I (On)".  
<Problem> You want to delete the PowerPoint add-in registration. (PPTC 2.0)  
Countermeasures  
Check Points  
Installing this projector software when Microsoft PowerPoint  
2000/2002 has already been installed on the personal  
computer, will result in the automatic registration of the add-in  
to PowerPoint.  
Please see the PowerPoint Help function for the method of  
deleting PowerPoint add-in registrations.  
The PowerPoint add-in registration will not be deleted even  
when this projector software is uninstalled.  
6-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Using the Projector in a Network  
<Problem> Projection to the screen is not possible when using the LAN environment. (DIU 2.0, IEU 1.0)  
Countermeasures  
Check Points  
Have LAN cards (i.e., adapters) been put into both the personal  
computer and the projector?  
Put LAN cards (i.e., adapters) into both the personal computer  
and the projector.  
Have the LAN settings (for both the personal computer and the  
projector) been completed?  
Perform the LAN settings for both the personal computer and  
the projector.  
Are a wired LAN and a wireless LAN being used simultaneously  
with the same personal computer?  
Please cancel either one of the LAN connections. When a built-  
in type is used, set it to "not used" under Properties.  
Image Express Utility 1.0 does not support the following:  
(1) Software using Direct X  
(2) MS-DOS screens  
(3) Microsoft Office assistant  
(4) IME  
(5) Moving pictures  
<Problem> Operation of this projector software becomes unstable. (DIU 2.0, IEU 1.0)  
Countermeasures  
Check Points  
When the network settings of the projector or personal  
computer are changed while this projector software (i.e.,  
Dynamic Image Utility 2.0 or Image Express Utility 1.0) is  
starting or running, the operation of the projector software may  
become unstable.  
Please restart the projector and the personal computer. When  
changes are to be made to the network settings, exit the  
projector software before making the changes.  
An application error occurs under Image Express Utility 1.0  
when the screen resolution is changed during Continuous  
Transmit.  
When changes are to be made to the screen resolution, exit  
Image Express Utility 1.0 before making the changes.  
<Problem> The colors become strange when Windows is set to 256 colors. (IEU 1.0)  
Check Points  
Countermeasures  
Image Express Utility 1.0 does not support 256 colors.  
Please set the Windows number of colors setting to High Color  
(15 bit) or higher.  
6-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Using the Projector in a Network  
<Problem> The projector cannot be found with "General search". (IEU 1.0)  
Check Points  
Countermeasures  
Are the wireless LAN settings appropriate?  
Are the channel numbers for the personal computer and the  
projector set to the same number?  
Please check the access points, the personal computer setting  
values and the projector [LAN Mode] setting values.  
When using the infrastructure or 802.11 Ad Hoc, please set to  
When WEP (encryption) has been set, has the same value been the same character string since SSID distinguishes between  
set for both the personal computer and the projector?  
upper and lower case characters.  
Are radio communication conditions satisfactory?  
Check whether there are obstacles located between the  
access point and the personal computer. Try moving the  
personal computer closer to the access point.  
Are the TCP/IP settings (e.g., IP address, sub net mask, etc.) of Check whether the network settings are within the same  
the personal computer and the projector correct?  
segment.  
Are more than one network interface cards (NIC) being used  
with the same computer?  
Set only the network interface card (NIC) that is connected to  
the projector to "Valid".  
For a network card that is not connected to the projector, click  
the network card name under "Control Panel" Ǟ "System" Ǟ  
"Device Manager" Ǟ "Network Adapter" and then click  
[Properties (R)] and set the device usage to "Not used".  
<Problem> Sometimes it takes a long time for screen transmission from the personal computer to the  
projector. (IEU 1.0)  
Countermeasures  
Check Points  
• Transmission time may be long depending on the image  
pattern.  
• When screens are sent to multiple projectors simultaneously,  
a larger number of projectors will result in longer transmission  
times.  
• The transmission time may vary depending on the network  
environment.  
• The transmission time may vary depending on the perfor-  
mance of the personal computer as well as other application  
software that is running at the same time.  
Transmission time will be longer when the resolution of the  
personal computer and that of the projector differ since there  
will be an increase in resolution conversion processing.  
We recommend that the resolution of the personal computer  
and that of the projector be set to the same setting value.  
The resolution of MT1065, MT1060, LT260 and LT240 are  
1024 x 768 dots.  
The resolution of LT220 and MT860 are 800 x 600 dots.  
<Problem> Cannot follow the screen switching processing of the PowerPoint slide show, etc. (IEU 2.0)  
Countermeasures  
Check Points  
Smooth screen switching processing or animation effects  
cannot be followed because in Image Express Utility 1.0, the  
screen condition of the personal computer is sent to the  
projector at a fixed time interval.  
Use the software with " the PowerPoint screen switching  
effects, animation effects, and other settings set to "None".  
6-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Setting Up for Double Stacking in  
Link Mode  
z Stacking and Connecting the Projectors ..................7-2  
x
Adjusting and Registering Signals to Be Projected........... 7-5  
c Adjusting the Lens Shift, Zoom and Focus to Clearly  
Display all projected patterns................................7-5  
v Link Mode Setting .....................................................7-5  
b List of Menu Items Available in Link Mode................7-6  
7-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Setting Up for Double Stacking in Link Mode  
z Stacking and Connecting the Projectors  
NOTE: Up to two units can be gravity stacked without external support. In some  
cases, however, two images will not align on the screen correctly. This will become  
more apparent when displaying small text and detailed graphics.  
Master projector  
Slave projector  
CAUTION: To prevent the projectors from falling, install them in a place and fasten them in a  
way with sufficient strength to support the two projectors. The projector with a lens weighs 21  
kg/46.3 lbs.  
z-1-3. On the remote control specify the ID number of the pro-  
z-1. Assigning Projector IDs  
jector to be adjusted. Press and hold the CTL and press  
MENU (ADDRESS) button to enter the ID number.  
You can operate the projector assigned the same ID number  
as the remote control.  
You can operate multiple projectors with the same remote con-  
trol.  
To do so:  
z-1-1. Select [Projector Options] → [Link Mode] → [Settings] →  
[Projector ID] a-nd assign an ID number to each projector. See  
also page 8-18.  
NOTE: Specifying "None" for projector ID allows you to operate multiple projectors  
concurrently. However, some projectors may not synchronize to the other projec-  
tors.  
z-1-2. Select the same communication speed for both the pro-  
jector.  
NOTE: Do not turn on [Master] or [Slave] at this time.  
7-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Setting Up for Double Stacking in Link Mode  
Throw Distances for Optional Lenses  
Master projector  
Screen center  
Slave projector  
Throw Distance  
Recommended Throw Distances for Double Stack  
Screen Size  
(inch)  
Throw Distance (inch)  
GT20ZL GT24ZLB GT34ZLB  
GT19ZL  
Screen Size  
(inch)  
Throw Distance (m)  
GT13ZLB  
GT13ZLB GT19ZL GT20ZL GT24ZLB GT34ZLB  
1.61  
2.44  
3.27  
4.10  
4.93  
6.18  
8.25  
9.91  
12.40  
-
63.6  
96.2  
128.9  
161.6  
194.3  
243.3  
325.0  
390.3  
488.4  
-
40  
60  
80  
0.94  
1.43  
1.92  
2.40  
2.89  
3.62  
4.84  
5.82  
7.28  
-
2.03  
3.05  
4.07  
5.09  
6.11  
7.63  
10.18  
12.21  
15.27  
-
-
-
-
40  
60  
80  
37.0  
56.2  
75.4  
94.6  
113.9  
142.7  
190.7  
229.1  
286.8  
-
80.1  
120.2  
160.2  
200.3  
240.4  
300.5  
400.7  
480.9  
601.1  
-
-
-
-
2.92  
3.93  
4.93  
5.93  
7.44  
9.95  
11.96  
14.97  
17.48  
19.99  
-
115.0  
154.5  
194.1  
233.6  
292.9  
391.7  
470.8  
589.3  
688.2  
787.0  
-
6.21  
7.78  
9.35  
11.70  
15.62  
18.76  
23.46  
27.38  
31.30  
35.22  
39.14  
244.6  
306.3  
368.0  
460.6  
615.0  
738.4  
923.6  
1078.0  
1232.3  
1386.6  
1541.0  
100  
120  
150  
200  
240  
300  
350  
400  
450  
500  
100  
120  
150  
200  
240  
300  
350  
400  
450  
500  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
NOTE:  
•
The optional lenses for GT5000 have different geometrical distortions in wide zoom and tele. Select the best zoom position for stacking where the geometrical  
distortion is as small as possible.  
•
The optional lens GT10RLB does not support stacking.  
For double stacking, follow the instructions described below.  
z-2. Stacking the Projectors  
Place the projectors at the proper height for best screen to projector relationship. Make sure that all projectors have the same display  
orientation.  
7-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Setting Up for Double Stacking in Link Mode  
z-3. Hookup  
z-3-1. Use commercially available RGB signal cables to connect the RGB output of the master projector to the RGB input of the  
slave projector until all the projectors are connected.  
z-3-2. Next, using a commercially available, bi-directional RS-232C cable connect the PC CONTROL OUT terminal of the master  
projector to the PC CONTROL IN terminal of the slave projector until all the projectors are connected.  
z-3-3. Turn all the projectors on and roughly make some optical adjustments to each projector.  
2
DVI  
AUDIO  
Example: Composite signal  
AUDIO OUT  
RGB 1  
SLOT  
1
SLOT 2  
USB(MOUSE/HUB)  
USB(PC)  
PC CARD  
1
L/MONO  
L/MONO  
PC CONTROL  
OUT  
LAN  
R
R
PC CONTROL  
IN  
Distribution amplifer  
AUDIO  
RGB  
2
R/Cr  
G/Y  
REMOTE  
REMOTE  
1
2
S-VIDEO  
RGB OUT  
OUT  
S-Video cable  
(not supplied)  
B/Cb  
SC TRIGGER  
VIDEO  
S-VIDEO  
H/  
HV  
IN  
OUT  
V
AC IN  
L/MONO  
R
L/MONO  
R
1
2
S-VIDEO  
INPUT  
S-VIDEO  
OUTPUT  
DVI  
AUDIO  
PC CONTROL  
IN  
AUDIO OUT  
RGB 1  
SLOT  
1
SLOT 2  
USB(MOUSE/HUB  
)
USB(PC)  
PC CARD  
L/MONO  
R
L/MONO  
LAN  
R
PC CONTROL  
IN  
AUDIO  
RGB  
2
R/Cr  
REMOTE  
REMOTE  
1
2
G/Y  
S-VIDEO  
RGB OUT  
OUT  
S-Video cable  
(not supplied)  
B/Cb  
SC TRIGGER  
VIDEO  
S-VIDEO  
H/  
HV  
IN  
OUT  
V
AC IN  
L/MONO  
R
L/MONO  
R
L
R
S-VIDEO  
VIDEO  
AUDIO OUT  
VIDEO OUT  
Bi-directional RS232C cable  
(not supplied)  
Video equipment  
NOTE: Connect a commercially available distribution amplifier to both the master  
and the slave projectors to distribute signal to two outputs of the master and the  
slave projectors.  
7-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Setting Up for Double Stacking in Link Mode  
x Adjusting and Registering Signals to Be c Adjusting the Lens Shift, Zoom and Fo-  
Projected  
cus to Clearly Display all projected patterns  
x-1. Display a desired input signal on the master projector.  
c-1. Display the internal crosshatch test pattern.  
x-2. Make adjustment to the signal, then save (register) adjust-  
ments on the master projector by pressing and holding CTL  
and pressing ENTRY LIST button on the remote control.  
NOTE: Use a different single color for each projector. Example: Turn on Green of  
master projctor, then Red of the slave projector.  
c-2.Adjust the Lens Shift by pressing and holding CTL and press-  
ing the POSITION button on the remote control.  
For lens shift adjustable range, see page 2-4 and 2-5. Lens  
Shift Adjustable Range.  
x-3.Repeat steps x-1 and x-2 for all signals you want to project.  
Display all the signals you registered and check.To check, select  
[Source Select] → [Entry List].  
c-3. Zoom the lens in and out by pressing and holding CTL and  
pressing the MAGNIFY(ZOOM)+/- button on the remote con-  
trol.  
x-4 Transferring Signal Data in the Entry List  
x-4-1.Transfer the data from the master projector to the slave  
projector so that both the projectors have the same data in  
memory.  
c-4.Adjust the lens focus by pressing and holding CTL and press-  
ing the FOCUS +/- button on the remote control.  
NOTE: If the physical (vertical) alignment of the projector is not correct, adjust the  
height of the feet. If there is any keystone distortion, use 3D-Reform (Keystone)  
adjustment to correct and save the settings on each projector. See page 3-4 for 3D-  
Reform correction.  
v Link Mode Setting  
v-1. Set the Link Mode on each projector.  
NOTE: Be sure to set the Link Mode on the slave projector before the master pro-  
jector. If you do this first on the master projector, you will not be able to set the Link  
Mode on the slave projector.  
v-1-1. Select [Projector Options] → [Link Mode] → [Settings].  
v-1-2. First select [Slave] on the slave projector.  
v-1-3. Select [Master] on the master projector.  
v-2. Projecting a Source Image from both the Projectors.  
v-3. Display any signal onto the screen.  
x-4-2. Select [Projector Options] → [Link Mode] on the mas-  
ter projector.  
x-4-3.Select [Entry List Copy] and press the ENTER button.  
The following will be displayed.  
v-4. Check to see if the images on the master projector are dis-  
played in synchronization with the ones on the slave projector  
while the projectors are in Link Mode.  
x-4-4.Select [OK] and press the ENTER button.  
The data has been transferred from the master projector to  
the slave projector.  
NOTE: Registering signals is not possible in the Link mode. To register a signal,  
first set "Link Mode" to "Standalone" on the menu and then repeat the steps from  
“x Adjusting and Registering Signals to Be Projected”. If you select an unregis-  
tered signal, the master projector displays the image, but the slave projector doesn't.  
To view the information on the currently displayed signal, select [Help] → [Source  
Information].  
x-5.Making Adjustments to the Slave Projector  
x-5-1. Display a desired input signal on the slave projector.  
x-5-2. Make adjustment to the signal, then save (register) ad-  
justments on the slave projector by pressing and holding  
CTL and pressing ENTRY LIST button on the remote con-  
trol.  
x-5-3. Repeat steps x-2 and x-2 for all signals you want to  
project.  
Display all the signals you registered and check. To check,  
select [Source Select] → [Entry List].  
7-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Setting Up for Double Stacking in Link Mode  
b List of Menu Items Available in Link Mode  
Available Menu Items  
Source Select  
Sound  
NOTE  
*1  
Menu  
Link Mode  
On/Off Timer  
Sleep Timer  
Source Information  
Projector Information  
Direct Button  
LENS SHIFT  
FOCUS  
NOTE  
*2  
*2  
Projector  
Projector  
Remote Control  
Projector  
*2  
*2  
ZOOM  
Remote Control  
*2  
"MENU/SELECT/  
ENTER/CANCEL"  
Projector  
Remote Control  
Projector  
POWER  
*3  
*3  
*3  
*1  
POWER ON  
POWER OFF  
INPUT  
MUTE(PICTURE)  
MUTE(SOUND)  
MUTE(OSD)  
Remote Control  
Remote Control  
Remote Control  
Remote Control  
Remote Control  
Remote Control  
*1: Unregistered signal is displayed on the master projector only and the picture is muted on the slave projector.  
*2: Adjustment is possible on each projector independently.  
*3:You can also turn on the slave projector only.  
7-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Using On-Screen Menu  
z Basic Menu Operation ............................... 8-2  
Projector Options .....................................8-13  
Menu ...................................................8-13  
Setup...................................................8-15  
Lamp Settings .....................................8-18  
Link Mode .......................................... 8-18  
LAN Mode .......................................... 8-19  
Setting a Password ............................ 8-22  
Security .............................................. 8-23  
Tools........................................................ 8-24  
Timer ...................................................8-24  
Using Capture .....................................8-26  
Using PC Card Files .......................... 8-26  
Using ChalkBoard .............................. 8-26  
Help..........................................................8-26  
Contents............................................. 8-26  
Source Information..............................8-26  
Projector Information.......................... 8-27  
Test Pattern ............................................. 8-27  
x List of Direct Button Combinations ............ 8-3  
c Menu tree ...................................................8-4  
v Menu Descriptions & Functions................. 8-7  
Adjust (Source) ......................................... 8-8  
Picture...................................................8-8  
Video Adjust ......................................... 8-8  
Picture Management ............................ 8-9  
Image Options.....................................8-10  
Option Adjust ..................................... 8-10  
Lens Memory ..................................... 8-11  
Signal Type..........................................8-11  
Sound...................................................... 8-11  
Ref. Adjust ............................................... 8-12  
Using 3D Reform ............................... 8-12  
Screen Type ....................................... 8-12  
Reference White Balance ...................8-12  
Reference Color Correction ............... 8-12  
Reference Lens Memory.....................8-13  
Factory Default ........................................ 8-13  
8-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Customizing the Menu  
z Basic Menu Operation  
The Custom menu can be customized to meet your requirements.  
Selecting a menu item from the "Custom Menu Edit" list, allows  
you to custom tailor the menu items to your needs.  
Using the Menus  
NOTE: The on-screen menu may not be displayed correctly while interlaced motion  
video image is projected.  
1. Select "Custom Menu Edit" to display the "Custom Menu Edit" screen.  
1. Press the MENU button on the remote control or projector cabinet to  
display the Basic, Advanced or Custom Menu.  
2. Use the SELECT ̆ or ̄ buttons to highlight your selection and press  
the ENTER button to place a check mark next to an option.  
MENU  
This action enables that feature. Press the ENTER button again to clear  
the check box.  
If you select an item with a solid triangle ̈ and press the ENTER but-  
ton on the remote control or the projector cabinet, you can enable all  
the items within that submenu. Also you can turn on an item within the  
submenu without placing a check mark on the main menu item.  
ADDR
NOTE: When using a USB mouse, click the mouse button to display the menu.  
For other operations, do the same way as you use your PC mouse.  
NOTE: Up to 12 main menu items (within Custom Menu Edit, not including  
submenu items) can be selected.  
3. In order for the changes to take effect, use the SELECT ̇ or ̈ button  
on the remote control or the projector cabinet to highlight "OK", then  
press the ENTER button.To cancel the changes, use the SELECT ̆ or  
̄ buttons to highlight "Cancel" and press the ENTER button.  
To return to the factory default, select "Reset" then press the ENTER  
button.  
2. Press the SELECT ̆̄ buttons on the remote control or the projector  
cabinet to highlight the menu for the item you want to adjust or set.  
-
NOTE: Once you have selected OK on the Custom Menu Edit screen, you cannot  
cancel the changes on the Menu screen. However, you can reedit the menu items  
over again as described in the steps above.  
NOTE: If the "Advanced Menu" item has been selected on the Menu mode, you get  
the "Change Custom menu now?" upon completion of "Custom Menu" editing. In  
this case, selecting "Yes" then "ENTER" will close all the menus and apply the changes  
from the Advanced menu to the Custom Menu. If you select "No" then "ENTER"  
functions, then all menu items will return to the Advanced menu, but your changes  
will still be available within the "Custom Menu" selection. To display the previously  
tailored Custom Menu, select "Custom Menu" from the "Menu Mode".  
3. Press the SELECT ̈ button or the ENTER button on the remote con-  
trol or the projector cabinet to select a submenu or item.  
-
+
An item "To Advanced Menu" will be added to the bottom of the  
Custom Menu.  
Selecting this item and pressing the ENTER button will display  
the "Advanced Menu" features.  
4. Adjust the level or turn the selected item on or off by using SELECT ̇  
or ̈ buttons on the remote control or the projector cabinet.  
The on-screen slide bar will show you the amount of increase or de-  
crease.  
-
+
5. Changes are stored until you adjust it again.  
ENTER  
CANCEL  
ENTER ........Stores the setting or adjustments.  
CANCEL......Return to the previous screen without storing set-  
tings or adjustments.  
6. Repeat steps 2-5 to adjust an additional item, or press the CANCEL  
button on the projector cabinet or the remote control to quit the menu  
display.  
8-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
x List of Direct Button Combinations  
CTL+ Input (1-10)  
Switches to any selected signal found in the Entry List.  
To enable this combination, you must first assign specific remote buttons  
for direct input selection in the Entry Edit window.  
CTL+ ENTER (While displaying Entry list)  
CTL+ CANCEL  
Displays the selected signal.  
Returns to the previous menu without closing the slidebar or dialog.  
CTL+ UNDO  
Clears all menus or adjustment/setting screens.All adjustments are saved  
automatically.  
CTL+ ̆̄̇̈  
Moves the slidebar or dialog box horizontally or vertically.  
Displays the magnifying glass icon.  
While using zoom on remote control:  
CTL+ ̇ (BS)  
Deletes one letter or numeral in the entry screen.  
Turns off the on-screen display forciblly.  
CTL+MUTE OSD  
CTL+ MENU (ADDRESS)  
CTL+ IMAGE (PROJECTOR)  
CTL+ POSITION (LENS)  
CTL+ KEYSTONE (R)  
CTL+ AMPLITUDE (G)  
Displays the remote ID entry window.  
Sequentially selects the Projector Options sub menu.  
Displays the Lens Shift adjustment window.  
Turns on red.Available only when the projector is in the test pattern mode.  
Turns on green. Available only when the projector is in the test pattern  
mode.  
CTL+ ENTRY LIST (B)  
Turns on blue.Available only when the projector is in the test pattern mode.  
Stores a signal in the Entry List when you are not displaying a test pattern.  
CTL+ MAGNIFY (ZOOM)  
CTL+ (FOCUS)  
Zooms the lens in and out  
Adjusts the lens focus.  
CTL+ INFO.  
Stores lens position settings.  
8-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
c Menu tree  
NOTE: The item appears dimmed on the menu, it is unavailable.  
1. RGB1  
Advanced Menu  
Source Select  
Adjust (Source)  
Sound  
2. RGB2  
3. DVI(DIGITAL)  
4. Video  
5. S-Video  
6. Viewer  
7. LAN  
Ref. Adjust  
Factory Default  
Projector Options  
Tools  
8. Slot 1  
Input Terminal 1/Input Terminal 2(available only when option board is installed)  
Input Terminal 1/Input Terminal 2(available only when option board is installed)  
RGB1(Video)/RGB1(S-Video)  
9. Slot 2  
0. RGB1(Video)  
Entry List  
Load/Cut/Copy/Paste/Store/Edit/All Delete  
Help  
Picture  
Brightness/Contrast/Saturation/Color/Hue/Sharpness  
Test Pattern  
Video Adjust  
Noise Reduction  
Color Matrix  
Off/Low/Medium/High  
HDTV/SDTV  
0 to 15  
Y/C Delay  
YTR Adjustment  
CTR Adjustment  
SweetVision  
Deinterlace  
Gain/Tap  
Gain/Tap  
Off/Low/Medium/High  
Off/On  
Split Mode (Off/On)  
Telecine  
Auto/Off  
Black Expansion  
0 to 5  
Contrast Enhancement -3 to +3  
3D Y/C Separation Off/On  
Picture Management Presentation/sRGB/Graphic/Video/Movie  
User  
Gamma Correction Dynamic/Natural/Black Detail  
Color Correction Red/Green/Blue/Yellow/Magenta/  
Cyan/Color Gain  
Color Temperature 6 Steps  
White Balance  
Base Setting  
Brightness R/G/B, Contrast R/G/B  
Presentation/sRGB/Graphic/Video/Movie  
Image Options  
Pixel Adjust  
Position  
Clock/Phase  
Horizontal/Vertical  
Aspect Ratio  
Resolution  
Overscan  
1.25:1(5:4)/1.33:1(4:3)/1.78:1(16:9)/1.85:1/2.35:1  
Auto/Native  
0%/5%/10%/25%  
Video Filter  
Blanking  
Off/Less/More  
Top/Bottom/Left/Right  
Mode 0-4/ Adjust  
Option Adjust  
Clamp Timing  
Sync Protection Upper/Lower  
VD Delay  
Adjustment/Field Invert (On/Off)  
Red/Green/Blue, Y/Cb/Cr, Y/Pb/Pr  
Signal Level  
Lens Memory  
Signal Type  
Set Custom Point/Use Custom Point  
RGB/Component  
Sound  
Volume/Bass/Treble  
8-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
NOTE: The shaded item indicates the default setting.  
3D Reform  
Conerstone  
Keystone  
Advanced Menu  
Source Select  
Adjust (Source)  
Sound  
Horizontal/Vertical  
Screen  
Screen Type 1.25:1(5:4)/1.33:1(4:3)/1.78:1(16:9)/1.85:1/2.35:1  
Position  
Ref. White Balance  
Brightness R/G/B, Contrast R/G/B  
Ref. Color Correction Red/Green/Blue/Yellow/Magenta/Cyan/Color Gain  
Ref. Adjust  
Factory Default  
Projector Options  
Tools  
Ref. Lens Memory  
Set Reference Point/Use Reference Point/Return to Factory Default/  
Use Point on Signal Change? Yes/No  
Picture Mute during Lens Shift? Yes/No  
Factory Default  
All Data (Including Entry List)/Current Signal  
Help  
Menu  
Page 1 Language  
English/Deutsch/Français/Italiano/Español/Svenska/  
Basic/Custom/Advanced  
Menu Mode  
Test Pattern  
Custom Menu Edit  
Menu Display Time Manual/Auto 5 sec./Auto 15 sec./Auto 45 sec.  
Date Format  
MM/DD/YYYY, MM/DD/YYYY ddd, DD/MM/YYYY,  
DD/MM/YYYY ddd, YYYY/MM/DD, YYYY/MM/DD ddd,  
Month DD, YYYY, Month DD, YYYY ddd  
Date, Time Preset Date Month/Day/Year (Day of the week), Time (H/M)  
Page 2 Display Select  
Date/Time/Input Terminal/Source Name/Projector ID/Message  
Color/Monochrome  
Page 3 Menu Color  
Mouse Pointer  
Pointer 1-9  
Setup  
Page 1 Orientation  
Background  
Desktop Front/Ceiling Rear/Desktop Rear/Ceiling Front  
Blue/Black/Logo  
RGBOUT Terminal Last/RGB 1/RGB 2  
Closed Caption  
Off/Caption 1-4/Text 1-4  
Sync Termination RGB 1(Hi-Z/75Ω)  
Page 2 Viewer Options  
Capture Options  
Mouse  
Show Folder List, Auto Play/Manual Play, Interval (5-300 sec)  
High Quality/Normal/High Compression  
Button (Right Hand/Left Hand),  
Sensitivity (Fast/Medium/Slow)  
Operation Mode Select (Auto/Projector)  
Page 3 Signal Select  
RGB 1 (RGB/Component, RGB, Component, Scart  
RGB2 (RGB/Component, RGB, Component, Scart)  
Video (Auto/NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)  
S-Video (Auto/NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)  
RGB1 (Video) (Auto/NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)  
RGB1(S-Video) (Auto/NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)  
Page 4 Auto Adjust (On/Off), Auto Start (On/Off), Power Management (On/Off),  
Power Off Confirmation (On/Off), 3D Reform Save (On/Off), Built-in Speaker (On/Off),  
Last Memory (On/Off), Idle Mode (On/Off), Back Light (On/Off), Screen Trigger (On/Off)  
Page 5 Remote Sensor  
S-Video Mode Select  
Clear Filter Usage Meter  
Page 6 Communication Speed 4800/9600/19200/38400  
Front/Back/Left/Right  
Off/S2  
Projector ID  
Enable (1-64)/Disable  
Default Source Select  
Last/Auto/Select  
Select: RGB1/RGB2/DVI(DIGITAL)/Video/S-Video/  
Viewer/LAN/Solt-1-1(None)/Solt-1-2(None)  
Solt-2-1(None)/Solt-2-2(None)/RGB1(Video)/  
RGB1(S-Video)  
Control Panel Key Lock Enable/Disable  
8-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Lamp Settings  
Link Mode  
Lamp Mode Normal/Eco  
Lamp Select Dual/Lamp 1/Lamp 2  
Advanced Menu  
Source Select  
Adjust (Source)  
Sound  
Interval  
Auto/1 week/4 weeks/1300H/1800H/3000H/4000H  
Lamp Type  
Settings  
Lamp1, Lamp2  
Mode  
Standalone/Master/Slave  
4800/9600/19200/38400  
Enable (1 - 64)/Disable  
Communication Speed  
Projector ID  
Entry List Copy  
Ref. Adjust  
Factory Default  
Projector Options  
Tools  
Link Mode(Master/Slave, ID, Status, Connected PJ)  
Reconnect  
LAN Card  
Status  
Status  
LAN Mode  
Build-in/PC Card  
Projector Name  
IP Address  
Subnet Mask  
MAC Address  
Advanced  
Help  
Test Pattern  
IP Address  
Automatic/Manual  
IP Address  
Subnet Mask  
Gateway  
On/Of  
DNS Configuration  
Domain Name  
Network Type  
Infrastructure/802.11 Ad Hoc/  
Mode  
Ad Hoc/Easy Connection  
SSID  
1-14  
Channel  
TX Rate  
Automatic/11M/5.5M/2M/1M/  
1M-2M-Automatic  
Disable/64 bit/128 bit  
Key 1-4  
WEP  
WEP  
Key Select  
Key 1-4  
On/Off  
Alert Mail  
Mail  
Sender's Address  
SMTP Server Name  
Recipient's Adderss 1-3  
Test Mail  
Password  
Security  
Menu, Logo  
Enable/Disable, Keyword, Use Protect Key, Drive/Read/Register/Delete  
Timer  
Execute Switch (Active/Inactive), Edit, Delete  
Preset Time (Off/0:30/1:00/2:00/4:00/8:00/12:00/16:00)  
On/Off Timer  
Sleep Timer  
Capture, PC Card Files, ChalkBoard  
Contents  
Source Information  
Projector Information  
Page 1 Source Name/Input Terminal/Entry No./Horizontal Frequency/  
Vertical Frequency/Sync Polarity  
Page 2 Signal Type/Video Type/Sync Type/Interlace/Direct Key  
Page 1 Remaining Lamp 1Time/Remaining Lamp 2 Time/  
Lamp 1 Hour Meter/Lamp 2 Hour Meter  
Page 2 Filter Usage/Projector Usage/Projector ID  
Page 3 Version (BIOS/Firmware/Data/FPGA)  
Test Pattern  
Cross Hatch/Gray Bars/Raster (0%)/Raster(25%)/Raster(50%)/Focus  
Raster(100%)/Raster Blue/Gray Raster 10/Gray Raster 30  
Red (On/Off), Green (On/Off), Blue (On/Off)  
8-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
v Menu Descriptions & Functions  
Entering Alphanumeric Characters by Using the Menu  
Alphabet or numeric characters are used for your IP address or  
projector name. To enter IP Address or projector name, use the  
software keyboard.  
Source Select  
Enables you to select a video source such as aVCR, DVD player,  
laser disc player, computer or document camera depending on  
what is connected to your inputs.  
For using the software keyboard, see page 10-10.  
Press the up/down buttons on your remote control or the projec-  
tor cabinet to highlight the menu for the item you want to project.  
* RGB1,2  
* DVI DIGITAL  
* Video  
* Viewer  
* LAN  
* RGB 1 (Video)  
* RGB 1 (S-Video)  
* S-Video  
Entry List  
Entering Alphanumeric Characters by Using the Remote  
Control Numeric Buttons  
Input alphanumeric characters by selecting one character at a  
time with the numeric (Source/Input) buttons 1through 10(0) and  
by moving the cursor with the SELECT ̈ button. After finishing  
the selection of the characters, press the ENTER button.  
Whenever one of the Source/Input buttons on the remote control  
is pressed, characters will be rotated.  
Displays the list of the entry signals. Use the SELECT ̆̄ but-  
tons on your remote control or the projector cabinet to select the  
signal and press the ENTER button on the remote control or the  
projector cabinet to display the Entry Edit Command screen.  
For example: A → B → C → 1 → A → ...  
Using the Entry List  
NOTE: When holding and pressing the CTL button and pressing one of the Source/  
Input buttons, another group of characters will be rotated.  
For example: a → b → c → ! → a → ...  
Making any adjustments to the current picture will automatically  
register its adjustments to the Entry List. The registered signal  
can be loaded any time from the Entry List.  
The alphanumeric characters corresponding to these Source/In-  
put buttons are as follows:  
NOTE: Up to 100 presets can be registered.  
Entry Edit Command  
Numeric buttons  
Press  
Press with CTL  
a → b → c → !  
d → e → f → ”  
g → h → i → #  
j → k → l → $  
m → n → o → %  
p → q → r → &  
s → t → u → '  
v → w → x → (  
y → z → ? → )  
; → : → + → -  
1
2
3
4
5
6
7
8
9
0
A → B → C → 1  
D → E → F → 2  
G → H → I → 3  
J → K → L → 4  
M → N → O → 5  
P → Q → R → 6  
S → T → U → 7  
V → W → X → 8  
Y → Z → / → 9  
* → , → . → 0  
You can edit signals on the Entry List.  
Load ............Enables you to select a signal from the list.  
NOTE: This can be done by pressing CTL and ENTER buttons.  
Store............Enables you to store the currently projected sig-  
nal.  
NOTE: This can be done by pressing CTL and ENTRY LIST buttons.  
Cut...............Enables you to remove a selected signal from  
the list and place it on the "clipboard" in the pro-  
jector.  
* If you have made an error in the input of a character, use the  
SELECT ̇ button and enter the correct letter or number.  
NOTE: Only numbers can be entered when you use the remote control Source/  
Input buttons while displaying the Software Keyboard.  
Copy .............. Enables you to copy a selected signal from the  
list and place it on the "clipboard" in the projec-  
tor.  
Paste ...........Enables you to paste the signal placed on the  
"clipboard" to any other line of the list.To do this,  
select "Paste" and then select the line number  
you want to paste to. Last press ENTER.  
8-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Edit ..............Enables you to change source names or assign Video Adjust (not available for RGB)  
the direct key.  
Noise Reduction  
Source Name  
Enter a signal name.Up to 18 alphanumeric char-  
acters can be used.  
Input Terminal  
Select one of the three levels for reducing video noise: Low, Me-  
dium or High.  
Change the input terminal. RGB1 and RGB2 are  
available for RGB signal;Video and S-Video are  
available for composite signal.  
NOTE: The lower the Noise Reduction level, the better the image quality by way of  
higher video bandwidth.  
Direct key  
You can assign specific remote keys for direct  
signal input selection.  
Color Matrix  
Lock  
Set so that the selected signal cannot be deleted  
when "All Delete" is executed.The changes can-  
not be saved.  
Select an appropriate color matrix for your input signal, either  
HDTV or SDTV.  
Skip  
Y/C Delay  
Set so that the selected signal will be skipped  
during auto search.  
When complete, select OK and press ENTER.  
To exit without storing setting, select Cancel. Adjusts Y/C delay level.  
Select "Source Name" and press ENTER to dis-  
play the Source Name Edit window. You can YTR Adjustment  
change source name on this window. Press [̄]  
to display the software keyboard, which you can  
enter alphanumeric characters. See page 10-10  
for the key function of the software keyboard.  
All Delete .....This feature enables you to delete all the regis-  
tered signals in the Entry List.  
Adjusts luminance transient time.  
The following buttons are not available for the currently project-  
ing signals:  
CTR Adjustment  
1) The Cut and Paste buttons on the Entry Edit Command screen  
2) The Input Terminal button on the Entry Edit screen  
Adjust (Source)  
Picture  
Adjusts chroma transient time.  
Brightness  
Adjusts the brightness level or the back raster intensity.  
Contrast  
Adjusts the intensity of the image according to the incoming  
signal.  
Saturation  
Adjust saturation at the white peak.  
Color  
Increases or decreases the color saturation level (not avail-  
able for RGB).  
Hue  
Varies the color level from +/- green to +/-blue.The red level is  
used as reference. This adjustment is only valid for Video and  
Component inputs (not available for RGB).  
Sharpness  
Controls the detail of the image for Video (not available for  
RGB).  
8-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
SweetVision  
3DY/C Separation  
This option turns on or off the 3 dimension separation feature.  
NOTE: This feature is available for NTSC3.58 of Video signal only.  
Picture Management  
The SweetVision feature provides improvement of contrast us-  
ing a proprietary detail enhancement technology.  
NOTE: This feature is not available for 480p, 576p and HDTV signals.  
Off ...............Turns off the SweetVision feature  
Low ..............Selects low level  
Medium .......Selects medium level  
High .............Selects high level  
This option allows you to adjust neutral tint for yellow, cyan or  
magenta.  
Split Mode  
There are 5 factory presets optimized for various types of im-  
ages, or you can set a user adjustable setting.  
This feature turns on or off to show the effect of the SweetVision.  
NOTE: When the projector is turned off, the Split Mode will return to Off.  
Presentation.. Recommended for making a presentation using  
a PowerPoint file.  
Deinterlace  
sRGB...........Standard color values  
Graphic ........Recommended for graphics  
Turns on or off the deinterlace function for a telecine signal.  
On ...............Default standard setting.  
Video ...........Recommended for regular picture such as TV  
program  
Movie...........Recommended for movies  
User.............User adjustable  
Off ...............Select this option if there is any jitter or artifacts  
in video.  
NOTE: This feature is not available for 480p, 576p and HDTV signals.  
NOTE: When "sRGB", "Graphic", "Video" or "Movie" is selected, the brightness de-  
creases slightly when compared to "Presentation". This is not a malfunction.  
Telecine  
User Adjust  
Use 3:2 pull down correction to eliminate jitter and artifacts in  
video.  
Auto .............For film source such as a DVD player  
Off ...............For signals other than film sources  
NOTE:  
• This feature is not available for 480p, 576p and HDTV signals.  
• When “Off” is selected in Deinterlace, this feature is not available.  
Black Expansion  
Minimizes blacks that appear more like shades of gray to provide  
a true black and white image at high contrast.  
When selecting the user adjustable presetting (User), the  
submenu will be displayed. You can customize each gamma or  
color.To do so, first select [Setting] and press the ENTER button,  
and then proceed the following steps.  
NOTE: This feature is not available for 480p, 576p and HDTV signals.  
Contrast Enhancement  
This option allows you to provide a high contrast image in a bright  
scene.  
NOTE: This feature is not available for 480p, 576p and HDTV signals.  
8-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Selecting Gamma Correction Mode  
Resolution  
Use the ̇ or ̈ buttons to choose one mode from three options. This allows you to activate or deactivate the Advanced AccuBlend  
Each mode is recommended for :  
feature.  
Dynamic ......For true color reproduction of natural tones  
Natural......... Normal settings  
Auto .............Turns on the Advanced AccuBlend feature. The  
projector automatically reduces or enlarges the  
current image to fit the full screen.  
Black Detail .For dark portions of a picture  
Native ..........Turns off the Advanced AccuBlend feature. The  
projector displays the current image in its true  
resolution.  
Selecting Color Correction  
Adjusts red, green, blue, yellow, magenta, cyan and color gain  
each independently to correct the tint on whole screen.  
NOTE:  
* When "Resolution" is set to "Native", "3D Reform", "Aspect Ratio", "Screen" and  
"Overscan" are not available.  
Adjusting Color Temperature  
* While you are displaying an image with higher resolution than the projector's  
native resolution, "Resolution" is not available.  
This feature adjusts the color temperature using the slide bar.  
Checking "ColorTemperature" enables the color temperature slide  
bar.  
Overscan  
Select overscan percentage (0%, 5%, 10% and 25%) for signal.  
Adjusting White Balance  
Press the White Balance button to access the Contrast/Bright-  
ness adjustment for each R, G, and B.  
NOTE: When "Resolution" is set to "Native", this feature is not available, and the  
stored settings and adjustments are invalid.  
NOTE: The White Balance is not available for Viewer and LAN.  
Video Filter (not available forVideo, Component,Viewer and  
LAN)  
Selecting Base Setting  
This function reduces video noise.  
This feature allows you to use color correction or gamma values  
as reference data to optimize for various types of images. You  
can select one of the following five settings.  
Off ...............The filter is removed.  
Less.............The low-pass filter is applied partially.  
More ............The low-pass filter is applied fully.  
• Presentation  
• sRGB  
• Graphic  
• Video  
• Movie  
Blanking  
Image Options  
This feature allows you to mask any unwanted area of the screen  
Pixel Adjust  
image.  
Adjust the Top, Bottom, Left or Right blanking with the SELECT  
Displays the Clock and Phase adjustments.  
̇ or ̈ button.  
Clock ...........Use this item to fine tune the computer image or  
to remove any vertical banding that might ap-  
pear.  
Option Adjust  
Clamp Timing  
Phase ..........Use this item to adjust the clock phase or to re-  
duce video noise, dot interference or cross talk.  
(This is evident when part of your image appears  
to be shimmering.) Use the ̇ and ̈ buttons to  
adjust the image.  
Use "Phase" only after the "Clock" is complete.  
Position  
According to the signal, this function sets the detection position  
(i.e., clamp position) of the black level reproduction of the analog  
input signal. Normally this is not used.  
Adjusts the image location horizontally and vertically using the  
SELECT ̇and ̈ buttons.  
Aspect Ratio  
Mode 0-4 .....Select the appropriate one.  
Adjust ..........This permits the video clamp position for each  
signal to be set. Use "Adjust" when a clamp tim-  
ing error occurs at the time of special analog sig-  
nal reception such as 1080P. Note that "Adjust"  
is not valid for doubler signals such as NTSC  
and PAL.  
You can select the aspect ratio for input signal.  
Select the appropriate aspect ratio using the SELECT ̇ or ̈  
button.  
To delete the "Clamp Timing" setting screen, select the SELECT  
̄ button and press the ENTER button, or press the remote con-  
trol CANCEL button.  
NOTE: When "Resolution" is set to "Native", this feature is not available, and the  
aspect ratio is set to “1.33:1 (4:3)”.  
8-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Sync Protection  
Lens Memory  
This function serves to store or apply the adjusted value when  
using the Shift, Focus and Zoom buttons on the projector or the  
remote control.  
When a VCR, DVD, or some other equipment that supports  
Copyguard (a copy prevention system) is played back, the screen  
may be displayed in a curved manner. Adjustments are made in  
such circumstances. Use the SELECT ̇ or ̈ button to adjust  
the VD level.  
Set Custom Point ........... Store the current adjusted values in  
memory.  
VD Delay  
Use Custom Point .......... Apply the adjusted values to the cur-  
rent signal.  
NOTE:  
• To enable the Lens Memory feature, select [Ref. Adjust] → [Ref. Lens Memory]  
and place a check mark next to “Yes” for [Use Point on Signal Change?].  
• The Lens Memory feature is not available in the Link Mode.  
• To store adjusted values common to all the input sources, use the Ref. Lens  
Memory. See page 8-13.  
Signal Type  
Adjustment:  
RGB/Component  
This feature is used to correct vertical jitter of a signal.  
NOTE: When connecting with a scan converter:  
If an image from the scan converter is not correctly displayed, adjust to select the  
best level point so that the image is displayed correctly.  
Select either the RGB signal type or the Component signal type.  
Field Invert:  
This feature is used to correct diagonal lines of a non-standard  
interlaced signal when they appear jaggy.  
Invert the odd or even field of a video signal.  
RGB ............RGB signal  
Component..Component signals such as Y/Cb/Cr, Y/Pb/Pr  
NOTE: This feature is available on RGB 1 and 2 only. If you do not get a better  
picture even when you set "Signal Select" to "Component" in Setup, set this to "Com-  
ponent".  
Signal Level  
Sound  
Volume/Bass/Treble  
Controlling Volume, Bass and Treble.  
Adjusts the sound, bass and treble level of the projector speaker  
and AUDIO OUT (RCA).  
R/G/B, Y/Cb/Cr or Y/Pb/Pr Gain:  
Adjust RGB, Component or HDTV Gain to match multiple pro-  
jector color uniformity.  
8-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Position  
Ref. Adjust  
This feature adjusts the vertical position of the image when view-  
ing video with an aspect ratio selected.  
When some aspect ratios are selected in Image Options, the  
image is displayed with black borders on the top and bottom.  
You can adjust the vertical position between top and bottom.  
Using 3D Reform  
This feature corrects trapezoidal distortion so that the projected  
image is rectangular.  
Two options are available for correcting procedures.  
You can save adjustment settings by using the 3D Reform Save  
option on Setup (See page 8-16).  
NOTE: This option is available only when "1.78:1 (16:9)", "1.85:1" and "2.35:1 " are  
selected in Screen Type and Aspect Ratio.  
Cornerstone  
NOTE: During 3D Reform adjustment, "Screen Type" and "Screen Position" may not  
be available. To make available, first reset the 3D Reform data and then do settings  
again. Secondly repeat the 3D Reform adjustment. Changing "Screen Type" and  
"Screen Position" can limit 3D Reform in its adjustable range.  
Reference White Balance [Ref. White Balance]  
See page 3-4.  
* When "Resolution" is set to "Native", "Cornerstone" and "Key-  
stone" are not available.  
Keystone  
Brightness R/G/B, Contrast R/G/B  
This feature adjusts the white balance that is used as a refer-  
1. Press the SELECT ̇ or ̈ button to adjust the horizontal keystone.  
2. Press the SELECT ̆ or ̄ button to select "Vertical".  
ence. This adjustment affects all sources.  
Reference Color Correction [Ref. Color Correction]  
3. Press the SELECT ̇ or ̈ button to adjust the vertical keystone.  
4. After completing, press the ENTER button. This will return to the menu  
screen.  
Screen  
Screen Type  
Select the correct aspect ratio for the screen to be used.  
See also "Aspect Ratio" on page 8-10.  
Red/Green/Blue/Yellow/Magenta/Cyan/Color Gain  
This option allows you to adjust red, green, blue, yellow, cyan,  
magenta or color gain.  
NOTE: When "Resolution" is set to "Native", this selection is inactive.  
8-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Including Entry List:  
Reference Lens Memory [Ref. Lens Memmory]  
Also deletes all the signals in the Entry List and  
returns to the factory preset.  
NOTE: Locked signals in Entry List cannot be deleted.  
Current Signal  
....................Resets the adjustments for the current signal to  
the factory preset levels.  
All the items in "Adjust (Source)" and "Sound"  
can be reset.  
NOTE: Locked signals in Entry List cannot be reset.  
Projector Options  
Menu  
This function serves to store the adjusted value common to all  
input sources when using the Shift, Focus, and Zoom buttons of  
the main unit or the remote control.  
[Page 1]  
Set Reference Point ............. Stores the current adjusted val-  
ues in memory as a reference.  
Use Reference Point ............ Applies the adjusted values  
stored in Set Reference Point to  
the current signal.  
Return to Factory Default ..... Returns the adjusted values to  
the factory default setting.  
Use Point on Signal Change? .... For change to take effect at the  
time of source selection, select  
“Yes”.  
Picture Mute during Lens Shift? ... To turn off the image and sound  
during lens shift, select "Yes".  
NOTE: This option is only available when  
"Yes" is selected for "Use Point on Signal  
Change?".  
Selecting Menu Language [Language]  
*
See "Tips on Adjusting Focus" on page 3-4 for more information.  
You can choose one of seven languages for on-screen instruc-  
tions.The options are:English, German, French, Italian, Span-  
ish, Swedish and Japanese.  
NOTE:  
• Adjusted values in Ref. Lens Memory will not be returned to default by using the  
Factory Default.  
• To store adjusted values for each input source, use the Lens Memory.  
Selecting Menu Mode [Menu Mode]  
This feature allows you to select 4 menu modes: Advanced,  
Custom, Basic and Service Menu.  
NOTE: In the Link mode the Lens Memory feature is not available.  
Advanced Menu ...... This is the menu that contains all the  
available menus and commands.  
Factory Default  
Basic Menu ............. This is the basic menu that contains mini-  
mum essentials of menus and com-  
mands.  
Custom Menu .......... This is the menu that you can customize  
using the Custom Menu Edit to fit your  
needs.  
Service Menu .......... For service personnel only.  
All Data /Current Signal  
The Factory Default feature allows you to change adjustments  
and setting to the factory preset for source.  
Customizing the Menu [Custom Menu Edit]  
See page 8-2 for instructions about how to customize the Menu.  
All Data........Reset all the adjustments and settings for all the  
signals to the factory preset except Ref. Lens  
Memory, Language, Background Logo, Commu-  
nication Speed, Projector ID, Lamp Settings, LAN  
Mode, Password, Security, Remaining Lamp1/2  
Time, Lamp 1/2 Hour Meter, Filter Usage and  
Projector Usage.  
8-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Selecting Menu Display Time  
[Page 2]  
This option allows you to select how long the projector waits  
after the last touch of a button to turn off the menu.  
The preset choices are "Manual", "Auto 5 sec", "Auto 15 sec",  
and "Auto 45 sec". The "Auto 45 sec" is the factory preset.  
Manual ........The menu can be turned off manually.  
Auto 5 sec ...The menu will automatically be turned off in 5  
seconds if no buttons are pressed within 5 sec-  
onds.  
Auto 15 sec .The menu will automatically be turned off in 15  
seconds if no buttons are pressed within 15 sec-  
onds.  
Auto 45 sec .The menu will automatically be turned off in 45  
seconds if no buttons are pressed within 45 sec-  
onds.  
Selecting Date Format  
Eight display formats can be selected. This date format sets  
the current date that appears on the upper left corner of the  
screen.  
Display Select  
You can choose the desired status information to be displayed  
on the screen.  
Setting the Current Date and Time [Date, Time Preset]  
You can set the current time, month, date, and year.  
The information selections are:  
Date, Time, Input Terminal, Source Name, Projector ID and  
Message.  
1. Type in date.  
Enter month, date and year in this order using Source/Input buttons on  
the remote control.  
Month and date must be entered in two digits. For example, to display  
"February", press "0" and "2".  
The Message selections are:  
Lamp life warning, lamp error, 3-minute before power off time,  
clearn filter, lock in Security and “Wait a moment”.  
2. Type in time.  
[Page 3]  
Time is expressed in the 24-hour format. For example, 6:00 p.m. is en-  
tered as 18:00.  
3. Select "OK" and press ENTER.  
Closing the window allows the clock to start.  
The current year, month, date and time are displayed on the top of the  
screen.  
NOTE: The projector has a built-in clock. The clock will keep working for about 3  
days after the main power is turned off. If the main power is off for 3 days or more,  
the built-in clock will cease. If the built-in clock ceases, set the date and time again.  
The built-in clock will not cease while in the standby or idle condition.  
Selecting Menu Color [Menu Color Select]  
You can choose between two color modes for menu color:color  
and monochrome.  
Selecting Mouse Pointer Icon [Mouse Pointer]  
This enables you to select from nine different mouse icons  
when using a USB mouse.  
NOTE: There may be cases where the Pointer function is not available (ex. a non-  
interlace signal at 15kHz such as video game.)  
8-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
[Page 2]  
Setup  
[Page 1]  
Setting Viewer Options [Viewer Options]  
Show Folder List:  
If this option is checked, when the Viewer source is selected  
on the projector, the folder lists will be displayed and allows  
you to select the presentation from a PC card.  
Selecting Projector Orientation [Orientation]  
This reorients your image for your type of projection. The op-  
tions are: desktop front projection, ceiling rear projection, desk-  
top rear projection, and ceiling front projection.  
Auto Play:  
If this option is checked, when the Viewer source is selected  
on the projector any given slide will start to play automatically.  
Selecting a Color or Logo for Background [Background]  
Use this feature to display a blue/ black screen or logo when  
no signal is available. The default background is "Blue". You  
can change the logo screen using the PC Card Files feature.  
See pages 4-4.  
Auto Play Interval:  
You can specify interval time between 5 and 300 seconds.  
NOTE: The Auto Play Interval time set on "Slide Show Settings" of the Dynamic  
Image Utility 2.0 overrides the one set here.  
Setting RGB 1 or 2 for RGB OUT [RGBOUT Terminal]  
This option allows you to determine which RGB source is out-  
put from the RGBOUT connector during Idle mode.  
Manual Play:  
Views a slide manually when the Viewer source is selected.  
Last .............The signal from the last RGB input will be output  
to the RGBOUT connector.  
Selecting Capture Options [Capture Option]  
(available for JPEG only)  
These options are used for the Capture function that you can  
select from Tools.You have three options for JPEG compres-  
sion quality: High quality, Normal and High Compression.  
RGB 1 ......... The signal from RGB1 IN will be output to the  
RGBOUT connector.  
RGB 2 ......... The signal from RGB2 IN will be output to the  
RGBOUT connector.  
High Quality............. Gives quality of JPEG a priority.  
Normal..................... Gives normal JPEG quality.  
High Compression... Gives compression a priority.  
NOTE:  
• The AUDIO OUT jack (RCA) will not output sound during the Idle mode.  
• The RGB signal can be output even when Video, S-Video, Viewer and LAN is  
selected.  
• When the DVI (DIGITAL) input is selected, the RGB OUTPUT terminal will not  
output signal.  
Setting Mouse Button and Sensitivity [Mouse]  
This option lets you to change your USB mouse settings. The  
mouse settings feature is available for USB mouse only.Choose  
the settings you want:  
Setting Closed Caption  
This option sets several closed caption modes that allows text  
to be superimposed on the projected image of Video or S-  
Video.  
Mouse Button .......... "Right Hand" or "Left Hand"  
Mouse Sensitivity .... "Fast", "Medium" or "Slow"  
CAPTION 1-4 ... Text is superimposed.  
TEXT 1-4 .....Text is displayed in full screen.  
OFF .............This exits the closed caption mode.  
Sync Termination (RGB1)  
This function is used to select the impedance of the sync sig-  
nal.  
Select " 75Ω" or "Hi-Z".  
NOTE: This should be "75Ω" for normal use. Select the "Hi-Z" when inputting a TTL  
signal.  
8-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Selecting Operation Mode [Operation Mode Select]  
Set the operation mode of the USB mouse connected to the  
USB port (MOUSE/HUB) on the projector  
[Page 4]  
Auto .............Depending on connection of the USB port (PC)  
on the projector and a USB port (type A) on your  
PC, the USB mouse is operated in the following  
way:  
* When connecting the projector to your PC  
The USB mouse connected to the projector  
can be used as a PC mouse.  
* When not connecting the projector to your PC  
The USB mouse connected to the projector  
can perform menu operation of the projector.  
Projector ......The USB mouse connected to the projector can  
perform menu operation of the projector.  
[Page 3]  
Enabling Auto Adjust [Auto Adjust]  
When "Auto Adjust" is set to "On", the projector automatically  
determines the best resolution for the current RGB input sig-  
nal to project an image using NEC's Advanced AccuBlend In-  
telligent Pixel Blending Technology.  
The image can be automatically adjusted for position and sta-  
bility;"Horizontal Position", "Vertical Position", "Clock", "Phase",  
and "Resolution".  
On ...............Automatically adjusts image "Horizontal Posi-  
tion", "Vertical Position", "Clock", "Phase" and  
"Resolution".  
Off ...............User can adjust the image display functions  
("Horizontal Position", "Vertical Position", "Clock",  
"Phase" and "Resolution") manually.  
Enabling Auto Start [Auto Start]  
Turns the projector on automatically when the power cable is  
inserted into an active power outlet and the main power switch  
is turned on.  
This eliminates the need to always use the "Power" button on  
the remote control or projector cabinet.  
Selecting Signal Format [Signal Select]  
RGB1/2  
Allows you to choose "RGB" for an RGB source such as a  
computer, or "Component" for a component video source such  
as a DVD player.  
Normally select "RGB/Component" and the projector automati-  
cally detects an either incoming signal. However there may be  
some component signals that the projector is unable to detect.  
If this is the case, select "Component". Select "Scart" in RGB  
1 or 2 for the European Scart.  
Enabling Power Management [Power Management]  
When this option is on and there is no input for five minutes or  
more, the projector will automatically turn itself off.  
Enabling Power Off Confirmation [Power Off Confirmation]  
This option determines whether a confirmation dialog for turn-  
ing off the projector will appear or not.  
VIDEO, S-VIDEO and RGB1 (Video and S-Video)  
This feature enables you to select composite video standards  
manually.  
Normally select "Auto". Select the video standard from the  
pulldown menu.This must be done forVideo and S-Video sepa-  
rately and "VIDEO" or "S-VIDEO" for RGB1 connector.  
Enabling Horizontal and Vertical Keystone Correction Save [3D  
Reform Save]  
This option enables you to save your current 3D Reform set-  
tings.Saving your change once affects all sources.The changes  
are saved when you turn off the projector.  
Selecting Built-in Speakers [Built-in Speaker]  
This option allows you to mute the built-in speakers.  
8-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Enabling Last Memory [Last Memory]  
S-Video Mode Select:  
The projector stores the last signal data in memory for each  
input (RGB1, RGB2, DVI DIGITAL, Video, S-Video and Slot 1/  
2).  
This feature is used to select the S-Video signal detection mode.  
This allows identifying of the S-Video signals with different as-  
pect ratio (16:9 and 4:3).  
This feature will reduce switching time between sources. If a  
commercially available switcher is connected, turning on this  
feature may cause the image to appear incorrectly.  
Should this happen, turn this feature off to mute the screen  
during switching.  
Off ...............Does not identify any S-video signal.  
S2 ................Identifies the 16:9 or 4:3 signal.  
NOTE: The Aspect Ration is not available when S2 signal is detected.  
Resetting the Filter Usage Hours [Clear Filter Usage Meter]  
Resets the filter usage back to zero. Pressing this button ap-  
pears a confirmation dialog box.To reset the filter usage hours,  
press "OK".  
Enabling Idle Mode [Idle Mode]  
The projector has two standby modes: Standby and Idle.  
Standby is the mode that allows you to put the projector in the  
standby condition which consumes less power than the idle  
mode. The projector is preset for Standby at the factory.  
When this check box is turned on, you allow the RGB OUT  
connector to output RGB signal during Idle mode.  
[Page 6]  
NOTE:  
* The RGB OUT connector will not output signal during the Standby mode.  
* Via the USB interface the projector can be turned on from your PC using Dy-  
namic Image Utility 2.0 during the Standby or Idle mode. On the LAN connection  
the projector can be controlled or monitored from your PC using Dynamic Image  
Utility 2.0 only in the Idle mode.  
* The HTTP server functions are not available during Standby mode. See page 10-  
11.  
Turning on or off the Back Light [Back Light]  
This function turns on or off the backlight of the buttons on the  
cabinet.  
NOTE: The Back Light feature is available in the normal operating mode or the idle  
mode only.  
Enabling Screen Trigger [Screen Trigger]  
When "Screen Trigger" is selected and the projector is pow-  
ered ON, the screen trigger output sends a low voltage trigger  
to the screen controller and the screen will go down.When the  
projector is powered OFF the screen trigger stops sending a  
low voltage trigger to the screen controller and the screen will  
go up. Use a commercially available stereo mini cable.  
Selecting Communication Speed [Communication Speed]  
This feature sets the baud rate of the PC CONTROL port (D-  
Sub 9 Pin). It supports data rates from 4800 to 38400 bps.  
The default is 38400 bps. Select the appropriate baud rate for  
your equipment to be connected (depending on the equipment,  
a lower baud rate may be recommended for long cable runs).  
[Page 5]  
Enabling and Disabling Projector ID  
Each projector needs its own unique addresses when used in  
serial communication mode.You can choose one of 64 unique  
address using the spin box. First select Enable. Keep pressing  
̈ button increases the number. To make your setting avail-  
able, select OK.  
Selecting Default Source [Default Source Select]  
You can set the projector to default to any one of its inputs  
each time the projector is turned on.  
Last .............Sets the projector to default to the previous or  
last active input each time the projector is turned  
on.  
Auto .............Searches for an active source in order of RGB1  
→ RGB2 → DVI(DIGITAL) → Video → S-Video  
→ Viewer → Slot 1 → Slot 2 → RGB1(Video) →  
RGB1(S-Video) → RGB1 and displays the first  
found source.  
Remote Sensor  
This option determines which remote sensors on the projector  
are enabled in wireless mode.  
The options are: front, rear, right, or left. All checked boxes  
indicate that they can accept the infrared signal from the sup-  
plied remote control.  
Select ..........Displays the selected source input every time the  
projector is started up. Select an input from the  
pull-down menu.  
8-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Disabling the Cabinet Buttons [Control Panel Key Lock]  
Link Mode  
This option turns on or off the Control Panel Key Lock function.  
NOTE:  
* This Control Panel Key Lock does not affect the remote control functions.  
* When the cabinet buttons are disabled, pressing and holding the CANCEL button  
for about 10 seconds will change the setting to enable.  
Lamp Settings  
Settings  
Selecting Standalone/Master/Slave  
This feature is used for multiple projector connection. The  
master projector is set to Master. The other slave projectors  
are set to Slave.When not using Link mode, set to Standalone.  
See page 7-5 for setting up for double stacking in link mode.  
The projector is designed to accept two lamps (dual lamp sys-  
tem). This dual lamp system provides prolong lamp life or high  
brightness or extra lamp (Extended life lamp).  
Selecting Communication Speed [Communication Speed]  
This feature sets the baud rate of the PC CONTROL port (D-  
Sub 9 Pin).This is the same procedure as in “Page 6”of“Setup”.  
NOTE: Be sure to use the same lamp type for both lamp 1 and 2.  
Enabling and Disabling Projector ID:  
Lamp Mode  
Each projector needs its own unique addresses when used in  
serial communication mode.This is the same procedure as in  
“Page 6” of “Setup”.  
This feature enables you to select two modes of the lamp:  
Normal and Eco. The lamp life can be extended by using the  
Eco mode.  
Copying Signals in the Entry List  
Normal Mode . This is the default setting (100% Brightness).  
Press the Entry List Copy button to copy all of the signals re-  
corded in the Entry List from one projector to another.  
Eco Mode ....Select this mode to increase the lamp life (80%  
Brightness).  
NOTE: When the optional Extended life lamp is used, the Lamp Mode is fixed to  
Eco mode.  
Lamp Select  
This feature allows you to select which lamp to be used.  
NOTE: This option is not displayed in the Basic menu.  
Dual .............Select to use the two lamps at the same time to  
increase brightness.  
Lamp1/2 ......Select to use one lamp of the two lamps. (Lamp  
1 on the right side and Lamp 2 on the left side  
when viewed from the front)  
Interval  
This allows you to specify the time for switching between the  
two lamps alternately. This option is available only when  
“Lamp1” or “Lamp2” is selected. When Auto is selected and  
one lamp has reached the end of its usable life, the other lamp  
is turned on. The lamp cannot be turned off for 60 seconds  
immediately after the lamp is turned on.  
NOTE: This option is not displayed in the Basic menu.  
Lamp Type:  
The lamp type you use and its information are displayed here.  
The information displayed here are:  
Light on or off, standard lamp or extended life lamp and re-  
maining hours.  
8-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Status  
LAN Mode  
This feature allows you to set various setting items when the  
projector is used on your network.  
Consult with your network administrator about these settings.  
NOTE:  
• Connect an Ethernet LAN cable to the LAN port (RJ-45) of the projector for net-  
work connection.  
• NEC's optional wireless LAN card is available. For more information on inserting  
or ejecting a LAN card, see page 5-2.  
• Either PC Card Slots 1 or 2 can accept LAN card. If two LAN cards are inserted  
into both PC card slots, the first inserted one is effective.  
• The standard built-in LAN feature and a commercially LAN card are available for  
network connection, but only one can be used at a time (mutual exclusion).  
CAUTION: Make sure that the LAN card is removed during  
Standby mode (NOT Idle mode) or with the main power off. Fail-  
ure to do so may cause damage to the data on your PC card.  
Displaying Current Status of Link Mode  
Status  
When selecting the tab "Status", you will get the following dia-  
log box.  
Master ID ................. Indicates the Master projector  
Status ...................... Indicates the status of the master pro-  
jector  
Connected PJ.......... Indicates number of connected slave  
projectors  
Slave No .................. Indicates serial number of the slave pro-  
jector  
ID ............................. Indicates ID of a slave projector  
Status ...................... Indicates the status of the slave projec-  
tor  
Reconnect button .... Confirms connection of all linked projec-  
tors  
Status items  
LAN Card  
Running ................... The projector is now working  
This option selects to use either LAN feature between the stan-  
dard LAN port (RJ-45) and an optional LAN card inserted in  
the PC CARD slot.  
Cooling Lamp .......... The fan is now cooling the lamp  
Standby ................... The projector is in stand-by or idle.  
Communication Error ...A communication error has occurred  
Projector Name  
Connecting .............. The projector is now verifying for con-  
nection  
Specify a unique projector name. Press ̄ to display the soft-  
ware keyboard and type in. Up to 16 alphanumeric characters  
can be used.  
Error Standby .......... An error caused the projector to enter  
the stand-by mode.  
IP Address............... Indicates the IP address of the projec-  
tor.  
Subnet Mask ........... Indicates the subnet mask of the projec-  
tor.  
MAC Address .......... Indicates the MAC address of the LAN  
card.  
Advanced ................ Displays the IP Address setting window.  
NOTE: Once you have selected "OK" on the Advanced screen, you cannot cancel the  
changes using "Cancel" on the LAN Mode screen.  
8-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Advanced  
Network Type (required for wireless only)  
IP Address  
Mode:  
Select communication method when using wireless LAN.  
An IP address can be automatically assigned to this projector  
by your DHCP server. If your network does not automatically  
assign IP address, ask your network administrator for an ad-  
dress, and then register it manually.  
Infrastructure  
....................Select this option when communicating with one  
or more equipment connected to the wireless or  
wired LAN network via an access point.  
Automatic ....Automatically assigns an IP address to the pro-  
jector from a DHCP server.  
802.11 Ad Hoc  
Manual ........Provides a space for you to register the IP ad-  
dress or subnet mask number obtained from your  
network administrator.  
....................Select this option when using the wireless LAN  
to communicate with a computer in a one-to-one  
correspondence.This is a method that meets the  
IEEE802.11 wireless standard.  
IP Address...Set your IP address. Press ̄ to display the soft-  
ware keyboard and type in 12 numeric charac-  
ters.  
Ad Hoc ........Select this option when using the wireless LAN  
to communicate with a computer in a one-to-one  
correspondence.  
Subnet Mask Set your subnet mask number. Press ̄ to dis-  
play the software keyboard and type in 12 nu-  
meric characters.  
Easy Connection  
....................This allows you to easily set up wireless LAN  
connection. See the Software Utility Installation  
section for more information.  
Gateway ......Set the default gateway of the network connected  
to the projector. Press ̄ to display the software  
keyboard and type in 12 numeric characters.  
See chapter 6 “Using the Projector in a Network”.  
Checking this box will make the set default route  
valid.  
SSID (Network name):  
Enter an identifier (SSID) for wireless LAN. Communication  
can be done only with equipment whose SSID matches SSID  
for your wireless LAN. Up to 32 alphanumeric characters can  
be used (Case sensitive).  
When data is sent from the LAN card, the trans-  
fer location will be searched according to the pre-  
viously set routing information; however, when  
the transfer location has not been found as a re-  
sult of the search, the data will be sent to the  
device that holds the IP address set here.The IP  
address that is set here must be one that can be  
identified by a search of the routing information.  
NOTE: To disable SSID, select a space (null) or "ANY"(All caps).  
Channel:  
Set this option when selecting [802.11 Ad Hoc] or [Ad Hoc] in  
[Mode].  
DNS Configuration  
Select a channel number from the pull-down list. The channel  
must match for all wireless devices communicating on your  
wireless LAN.  
....................Type in the IP address of DNS server on the net-  
work connected to the projector.  
12 numeric characters are used.  
Domain Name  
NOTE: Channels in the pull-down list are different depending on which country you  
live in.  
....................Type in domain name of the network connected  
to the projector. Up to 60 alphanumeric charac-  
ters can be used.  
TX rate:  
Select a wireless transmission speed. Normally leave it as Au-  
tomatic.  
Try another transmission speed when the connection fails.  
8-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
WEP (for Wireless only)  
Mail  
Select this option whether using the WEP (Wired Equivalent Pri-  
vacy) key for encryption or not. To use encryption, specify WEP  
key.  
NOTE: To the Mail Alert feature on wireless LAN connection, select "Infrastructure"  
for "Mode" in "Network Type." .  
Alert Mail:  
Disable ........Will not turn on the encryption feature.Your com-  
munications may be monitored by someone.  
Checking this box enables Alert Mail feature.  
This option notifies your computer of an error message via e-  
mail when using wireless or wired LAN. The error message  
will be notified when the projector lamp has reached the end  
of its usable life or an error occurs in the projector.  
64bit ............Uses 64-bit datalength for secure transmission.  
128bit ..........Uses 128-bit datalength for secure transmission.  
This option will increase privacy and security  
when compared to use of 64bit datalength en-  
cryption.  
Sample of a message sent from the projector:  
The lamp is at the end of its usable life. Please replace the  
lamp.  
NOTE: The WEP settings must be the same as communication devices such as PC  
or access point in your wireless network. When you use WEP, your image trans-  
mission speed will slow down.  
Projector Name: X X X X  
Lamp 1 Hour Meter: xxxx [H]  
Lamp 2 Hour Meter: xxxx [H]  
Projector Usage: xxxxxx [H]  
Key Select:  
Selects one key from the four keys below when selecting [64bit]  
or [128bit] in [WEP].  
Key1-4:  
Sender's Address:  
Enter encryption key when selecting [64bit] or [128bit] in [WEP].  
Up to 5 characters can be set in 64 bit and up to 13 characters  
in 128 bit.  
Specify the senders address. Use the Software keyboard. Up  
to 60 alphanumeric and symbols characters can be used. See  
"Using Software Keyboard" in Appendix for more details.  
The key can also be set in hexadecimal digit.  
* Enter 0X(numeral and alphabet respectively) right in front  
of your key code.  
* Hexadecimal uses 0 to 9 and A to F.  
* Up to 10 characters can be set in 64 bit and up to 26  
characters in 128 bit.  
SMTP Server Name:  
Type in the SMTP server name to be connected to the projec-  
tor. Up to 60 alphanumeric characters can be used.  
Recipient's Address 1 to 3:  
Type in your recipient's address. Up to 60 alphanumeric and  
symbols characters can be used.  
NOTE: Only numbers can be entered when you use the remote control Source/  
Input buttons.  
Test Mail:  
Send a test mail to check if your settings are correct.  
NOTE: If you entered an incorrect address in a test, you may not receive an Alert  
mail. Should this happen, check if the Recipient's Address is correctly set.  
NOTE: Unless any one of the "Sender's Address", "SMTP Server's Name" or  
"Recipient's Address 1-3" is selected, "Test Mail" is not available.  
NOTE: Be sure to highlight “OK” and press the ENTER button before executing  
“Test Mail”.  
8-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Setting a Password  
Delete  
A password can be set for your projector to avoid operation by  
an unauthorized person.  
There are two password options: one for menu and the other for  
logo.  
When a password is set, doing any one of the following four op-  
erations will display the Password input screen.  
For Menu:  
To delete your password:  
*
Changing the menu to Advanced  
1. Highlight [Delete] and press the ENTER button. The "Current Pass-  
word" screen will be displayed.  
*
Editing the custom menu  
For Logo:  
*
Changing the background  
2. Use the Software keyboard to type your password. Highlight "OK" on  
the “Current Password” screen and then press the ENTER button.  
*
Changing the logo data in PC Card Files  
Your password will be deleted.  
Procedures for Password setting apply to both Menu and Logo.  
In case you forget your password, follow the steps below to  
delete it.  
Entry  
To assign your password:  
1. Select the Advanced menu from the Basic menu. The "Password"  
entry screen will be displayed.  
2. Use the Software keyboard to type "1111".  
Highlight "OK" on the “Password” entry screen and then press the  
ENTER button.  
NOTE: Up to 15 alphanumeric characters can be assigned.  
• Only numbers can be entered when you use the remote control Source/Input  
buttons.  
The "Password Warning!!" message will be displayed.  
3. Use the Software keyboard to type "3333".  
Highlight "OK" on the “Password” entry screen and then press the  
ENTER button.  
The "Password Warning!!" message will be displayed.  
4. Use the Software keyboard to type "5555".  
Highlight "OK" on the “Password” entry screen and then press the  
ENTER button.  
The "Delete Password. Are you sure? Yes/No" dialog box will be dis-  
played.  
5. Use the SELECT ̇ or ̈ button to highlight "Yes" and press the EN-  
TER button.  
1. Type a password.  
Highlight "Entry" and press the ENTER button.  
The "Enter the Password screen" will be displayed.  
Your password will be deleted.  
Make sure that "̄" is highlighted and then press the ENTER button.  
The Software keyboard appears. Use the Software keyboard to type a  
password and then highlight "OK" on the “Enter the Password” screen  
and press the ENTER button.  
The [Confirm Password] screen will be displayed.  
2. Type the same password again. Highlight "OK" on the “Enter the Pass-  
word” screen and press the ENTER button.  
Your password will be assigned.  
8-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Security  
To register a PC card as a protect key.  
The Security function enables you to protect your projector so  
that the projector will not project a signal unless you enter a key-  
word. There is also an option to lock the projector by using a  
registered PC card as a protect key. Once you have registered  
your PC card as a protect key, you are required to insert the  
registered PC card into the PC card slot of the projector each  
time you turn on the projector.You can enable the Security func-  
tion by using a keyword only.  
1. Insert a PC card into the PC card slot of the projector.  
2. Use the SELECT ̆̄ button to select “Use Protect key” and press the  
ENTER button. A check mark will be placed.  
3. Use the SELECT ̆̄ button to select "Read" and press the ENTER  
button.  
Data of the PC card will be read into the projector.  
4. Use the SELECT ̆̄ button to select "Register" and press the ENTER  
button.  
Downloaded data will be registered and be displayed in the list window.  
5. Use the SELECT ̆̄ button to select "Keyword" and use the software  
keyboard to enter a keyword.  
NOTE: To use a PC card as a protect key, you must also set up a keyword. Please  
make a note of your keyword.  
This completes registration of your PC card.  
To enable Security, use the SELECT ̆̄ button to select "En-  
able" and use the SELECT ̆̄ button to select "OK" and "Secu-  
rity function will be enabled. An “Are you sure?" message will  
appear. Use the SELECT ̇̈ button and press the ENTER but-  
ton.  
The Security function takes effect.  
Enable/Disable ........ This turns the Security function on or off.  
To turn on the projector when Security is enabled (when  
using your keyword only).  
Keyword .................. Enter an appropriate keyword when you  
use the Security function.  
NOTE: Only numbers can be entered when you use the remote control Source/  
Input buttons.  
(Up to 10 characters can be used.)  
The Security function is available only  
when your keyword is entered.  
1. Press and hold the POWER button for a minimum of two seconds.  
The projector will be turned on and display a message to the effect that  
the projector is security-protected.  
Use Protect key ....... Check this box to lock your projector  
when using a PC card. To use a key-  
word without a PC card, do not check  
this box.  
2. Select [Projector Options] → [Security] from the menu and press the  
ENTER button.  
The Release Code input screen will be displayed.  
Drive ........................ Switches between PC Card slots.  
Read........................ Reads data of a PC card.  
Register ................... Registers data of the PC card.  
3. Enter your keyword in the Release Code input screen.  
You can view the projected image.  
NOTE: Do not forget your keyword. However, if you forget your keyword, NEC or  
your dealer will provide you with your Release Code. See more information at  
the end of this section.  
The Security function is not available un-  
less at least one PC card is registered.  
(if the “Use Protect key” check box is se-  
lected)  
To turn on the projector when Security is enabled (when  
using a PC card as a protect key).  
Up to 5 PC cards can be registered.  
Delete ...................... Deletes data of a registered PC card.  
1. Insert your registered PC card into the PC card slot.  
2. Press and hold the POWER button for a minimum of two seconds.  
The projector will turn on and then recognize the PC card. Once the  
image has been projected, it will stay on without the PC card.  
To set up a keyword to enable the Security function without  
using a registered PC card.  
•
The security disable mode is maintained until the main power is turned  
off (by setting the main power switch to "O" or unplugging the power  
cable).  
NOTE: Only numbers can be entered when you use the remote control Source/  
Input buttons.  
1. Use the SELECT ̆̄ button to select “Keyword” and use the software  
keyboard to enter a keyword.  
In the following cases you will be asked to check the protect key or  
input the keyword:  
NOTE: Please make a note of your keyword.  
(1) When "OK" is selected at an image for which security is set and  
the power is turned off then back on  
2. Use the SELECT ̆̄ button to select “Enable” and use the SELECT  
̆̄ button to select “OK”, then the Security function will be enabled. An  
“Are you sure?” message will appear. Use the SELECT ̇̈ button and  
press the ENTER button.  
(2) When the main power is turned off then back on while the security  
function is enabled  
(3) When you attempt to display an image for which security is set  
while the security function is enabled  
The Security function takes effect.  
•
Blanks (spaces) cannot be used in the Keyword section.  
8-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
To delete PC card data you registered.  
Tools  
Provides tools for setting On/Off timer, sleep timer, capturing im-  
ages, displaying files or changing your background logo in a PC  
Card and drawing.  
1. Use the SELECT ̆̄ button to select "Delete" and use the SELECT ̇  
button to select the list window.  
2. Use the SELECT ̆̄ button to select the PC card data you wish to  
delete.  
Timer  
3. Press the SELECT ̈ button to select "Delete" and press the ENTER  
button.  
Enables you to turn on or off your projector automatically at a  
specified time. Two timer functions are available: On/Off Timer  
and Sleep Timer.  
The PC card data will be deleted.  
NOTE: The projector has a built-in clock. The clock will keep working for about  
three days after the main power is turned off. If the main power is not supplied to  
the projector for three days or more, the built-in clock stops working.  
If you've lost your registered PC card, proceed as follows:  
NOTE: NEC or your dealer will provide you with your Release Code in exchange for  
your registered keyword and Request Code. See URLs at the end of this section.  
On/Off Timer  
1. Press and hold the POWER button for a minimum of two seconds.  
The projector will be turned on and display a message to the effect that  
the projector is security-protected.  
2. Select [Projector Options] → [Security] from the menu and press hte  
ENTER button.  
The Release Code input screen will be displayed as well as your Re-  
quest Code (24 alphanumeric characters).  
3. Enter your Release Code in the Release Code Input screen.  
*
If the projector is turned on by entering the Release Code, your Secu-  
rity will be disabled.  
NOTE:  
* Some types of PC cards cannot be registered as your protect key.  
* It is recommended that you register two or more PC cards in case you lose or  
damage your registered PC card.  
Up to 10 settings can be programmed.  
Before setting On/Off Timer, make sure that Date, Time Preset feature  
is set.  
* Formatting your registered PC card will disable your protect key function.  
•
NOTE:  
•
Even after setting On/Off Timer, turning the projector on or off with the  
remote control is possible.  
For additional information visit:  
US : http://www.necvisualsystems.com  
Europe : http://www.nec-europe.com/  
Global : http://www.nec-pj.com/  
Setting the On or Off Timer  
1. Open the On/Off Timer window.  
2. Select a program number (No. 1 to 10) by using the SELECT ̆ or ̄  
button.  
8-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
3. Select “Edit” and press the ENTER button to open the Edit window.  
Enabling the On or Off Timer  
1. To execute the setting, select “Active” .  
4. Set the Day, Time (24 hours format), On-Time and Off-Time using the  
SELECT buttons and the Software keyboard (1 thru 10).  
2. Select “OK” and press the ENTER button.  
NOTE: When one program or more are specified, all the settings are active.  
NOTE: The settings will be executed in numerical order. Finished settings will be  
automatically deleted.  
NOTE: The On/Off Timer will not work while the cooling fans are running or an error  
message appears. Do not turn off the main power switch in this condition.  
Disabling the On or Off Timer  
To disable the setting, select “Inactive”. Select “OK” and press  
the ENTER button.  
5. Select On Timer or Off Timer  
Deleting the On or Off Timer settings  
1. Select the setting you want to delete.  
6. Repeat the Timer  
To repeat the OnTimer or OffTimer program every week, place a check  
mark in “Repeat”.  
7. Select “OK” and press the ENTER button on the remote control to com-  
plete the setting.To cancel this and return to its previous screen, select  
“Cancel”.  
2. Select “Delete” and press the ENTER button.  
NOTE: If there is no operation for 4 hours or more after the projector is turned on  
with On-Timer function, the projector will enter the standby or idle mode.  
3. Select “OK” and press the ENTER button to complete the deletion.  
4. Select “Delete” again and press the ENTER button to return to the pre-  
vious screen.  
8-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Enabling Sleep Timer  
Using ChalkBoard  
The ChalkBoard feature allows you to write and draw messages  
on a projected image. See page 4-4.  
NOTE: This feature is available only when using with USB mouse.  
Help  
1. Select your desired time between 30 minutes and 16 hours: Off, 0:30,  
1:00, 2:00, 4:00, 8:00, 12:00, 16:00.  
2. Select “Set” and press the ENTER button on the remote control.  
3. The remaining time starts counting down.  
Contents  
4. The projector will turn off after the countdown is complete.  
NOTE:  
• To cancel the preset time, set "Off" for the preset time or turn off the power.  
• When the remaining time reaches 3 minutes before the projector is turned off,  
the "Projector will turn off in 3 minutes" message will be displayed on the bottom  
of the screen.  
Using Capture  
Allows you to capture an image from a source that is currently  
being displayed. The image is saved as JPEG in the PC card.  
When you select Capture from the menu, you will get a tool bar.  
You can capture an image directly using the tool bar when the  
menu is not displayed. See page 5-4.  
Using PC Card Files  
Provides an online help about how to use the menus. An under-  
lined link means that you can move to an adjustment item di-  
rectly.  
Selecting the underlined link and pressing ENTER moves to the  
corresponding adjustment item.  
NOTE: The Help menu may not be displayed correctly when an image is overscanned.  
Source Information  
Information  
Displays the status of the current signal. This dialog box has  
two pages.  
Page 1  
The PC Card Files feature allows you to display a list of all the  
files stored in the PC card so that you can select a file you want  
to display.You can also sort files by file name or date, or display  
the file. See page 4-4.  
Changing Background Logo:  
You can change the default background logo using the PC Card  
Files feature. See page 4-4.  
NOTE: File size must be 256KB or less. Other file formats than JPEG and BMP are  
not available. See page 4-4.  
Source Name, Input Terminal, Entry No., Horizontal Frequency,  
Vertical Frequency, Sync Polarity  
8-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Using On-Screen Menu  
Page 2  
Page 2  
Filter Usage, Projector Usage, Projector ID  
Page 3  
Signal Type, Video Type, Sync Type, Interlace, Direct Key  
Projector Information  
Displays the information for your projector such as lamp usage,  
filter usage, version number and others.This dialog box has three  
pages.  
Page 1  
Version (BIOS/Firmware/Data/FPGA)  
Test Pattern  
Remaining Lamp 1 Time, Remaining Lamp 2 Time, Lamp 1 Hour  
Meter, Lamp 2 Hour Meter  
NOTE: The progress indicator shows the percentage of remaining bulb life.  
The value informs you of the amount of lamp 1 and 2 respectively.  
• When the remaining lamp time reaches 0, the Remaining Lamp Time bar indica-  
tor changes from 0% to 100 hours and starts counting down. If the remaining  
lamp time reaches 0 hour, the projector will not turn on.  
Press to display the test pattern. Pressing this button sequen-  
tially selects 10 test patterns for each red, green and blue.  
Lamp life (H)  
Type  
Model  
Normal  
1500H  
Eco  
Standard lamp  
2000H  
GT60LP  
4500H  
Extended life lamp  
GT60LPS  
NOTE: The lamp life is typically 1500 hours in Normal mode (2000 hours in Eco  
mode).  
The lamp life, however, may be decreased under certain conditions and the lamp  
could reach end of life within the specified time.  
8-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Maintenance  
z Replacing the Lamp..................................................9-2  
x Replacing or Cleaning the Filter ...............................9-3  
c Cleaning the Cabinet and the Lens ..........................9-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Maintenance  
3. Insert a new lamp housing until the lamp housing is plugged into the  
socket.  
This chapter describes the simple maintenance procedures you  
should follow to replace the lamp and the filter, and to clean the  
filter and the cabinet.  
CAUTION: Do not use a lamp other than the NEC replacement lamp  
(Standard life lamp: GT60LP or Extended life lamp: GT60LPS).  
z Replacing the Lamp  
The projector has two lamps. The lamp replacement procedure  
applies to both lamps. After your lamp 1 and 2 has been operat-  
ing for 1500 hours (Normal mode on the standard life lamp) or  
longer, the "Lamp" indicator in the cabinet will blink red and the  
message will appear. Even though the lamp may still be working,  
replace it as soon as possible to maintain optimal projector  
performance.  
NOTE: Be sure to use the same lamp type for both lamp 1 and 2.  
CAUTION  
•
DO NOT TOUCH THE LAMP immediately after it has been used. It will  
be extremely hot. Turn the projector off, wait 90 seconds, turn off the  
main power switch, and then disconnect the power cable. Allow at least  
one hour for the lamp to cool before handling.  
4. Secure it in place with the two screws.  
Be sure to tighten the screws.  
•
•
DO NOT REMOVE ANY SCREWS except the lamp cover screw and  
the two lamp case screws.You could receive an electric shock.  
The projector will turn off and go into stand by mode after 1600 hours  
(Normal mode on the standard life lamp) of service. If this happens, be  
sure to replace the lamp. If you continue to use the lamp after 1500  
hours (Normal mode on the standard life lamp) of use, the lamp bulb  
may shatter, and pieces of glass may be scattered in the lamp housing.  
Do not touch them as the pieces of glass may cause injury. If this hap-  
pens, contact your NEC dealer for lamp replacement.  
•
When "Dual" is selected in "Lamp Select" of "Lamp Settings", replace  
both lamp 1 and 2 at the same time so that the projector can keep the  
color of projected image even.  
5. Reattach the lamp cover.  
To replace the lamp:  
1. Loosen the lamp cover screw until the screwdriver goes into a free-  
wheeling condition and remove the lamp cover. The lamp cover screw  
is not removable.  
6. Tighten the lamp cover screw. Be sure to tighten the screw.  
2. Loosen the two screws securing the lamp housing until the screwdriver  
goes into a freewheeling condition.The two screws are not removable.  
Remove the lamp housing by pulling out the handle.  
NOTE: Replacing a new lamp automatically clears the lamp usage hours.  
NOTE: The lamp housing has an EEPROM chip memorizing its amount of usage  
hours. You can check the amount usage hours in Information of the menu. (The  
standard lamp and the optional lamp have an EEPROM chip in it so that when you  
remove it, your lamp usage hours are saved in its own memory. The projector  
reads the lamp usage hours from the EEPROM chip to display them in Information  
of the menu.)  
Interlock  
NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do  
not attempt to circumvent this interlock.  
9-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Maintenance  
The air-filter sponge prevents dust or dirt from getting the inside  
of the projector and should be cleaned after every 100 hours of  
operation (more often in dusty conditions). If the filter is dirty or  
clogged, your projector may overheat.  
x Replacing or Cleaning the Filter  
To replace the filter:  
• Replace both filters at the same time.  
• Before replacing the filters, remove dust and dirt from the pro-  
jector cabinet.  
• The projector contains high-precision parts. Keep out dust and  
dirt during filter replacement.  
• Do not wash the filter with water. Water will damage the filter  
membrane.  
• Reattach the filter cover correctly. Failure to do so may cause  
projector malfunction.  
CAUTION  
•
Turn off the power, wait for 90 seconds, turn off the main power and  
unplug the projector before replacing the filter.  
•
•
Do not attempt to operate the projector without filter.  
Your projector will not operate unless the filter cover is installed cor-  
rectly.  
To clean the filter:  
Pull out the filter by pushing up on the catch. Vacuum the filter-  
Preparation: Replace the lamp before replacing the filters.  
through the filter.  
1. Pull out the filter cover by pushing up on the catch.  
(This must be done to the filters on both left and right.)  
2
1
The "Please clean the filters" message will be displayed each  
time the projector is turned on after it has been used in excess of  
168 hours. Should this message appear, clean the filters.  
NOTE:  
* The message can be turned on or off using the "Message" option on the Setup  
menu. See page 8-14.  
Filter holding frame  
Filter cover  
Filter  
* After cleaning the filters and resetting the filter usage time back to zero, the mes-  
sage will not be displayed.  
See page 8-17 for resetting the filter usage time.  
2. Replace both filters.  
1. Remove the filter and clean the filter cover.  
1
2
2. Place the new filter on the filter cover in the correct direction.  
3. Reinstall the filter cover. (This must be done to both left and right)  
4. Plug the power cable into a wall outlet and turn on the projector.  
5. Reset the filter usage hours to zero.  
Select [Menu] → [Projector Options] → [Setup] → [Page 5] → [Clear  
Filter Usage Meter] → [OK]. Press the ENTER button.  
9-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Maintenance  
c Cleaning the Cabinet and the Lens  
F
O
C
U
S
Z
P
O
C
C
O
M
A
R
D
1
F
P C  
C
A
R
D
Z
2
D
E
F
T
L
L A  
O
W
M
N
P
1
L
E
N
S
S
H
L A  
I F  
T
M
P
2
R
U
P
I G  
H
T
S
R
E T N E  
T
1
A
T
U
S
C
A
P
N
O
2
W
C
S
E
E
E
R
E
L
C
T
O
LAN  
N
/ S  
M
T
E
A
N
U
N
D
B
3
D
Y
R
E
F
O
R
M
3
RMOTE1  
D
A
U
PCARD  
OUT  
T
O
A
D
J
A
)
(
U
S
RMOTE2  
T
PC  
U
IN  
)
ACIN  
PCNTROL  
IN  
(
MOSE/HUB  
UBS  
OTU  
SCTIGER  
DIV  
SOLT2  
ADUIO  
SOLT1  
RBG1  
LM/NO  
R
RC/r  
ADUIO  
GY/  
AIDOUT  
BC/b  
RBG2  
H/  
L
HV  
R
V
RBGOUT  
SV-IDEO  
VDIEO  
LM/NO  
R
LM/NO  
R
1. Turn off the projector before cleaning.  
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol  
or thinner.  
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.  
F
O
C
U
S
Z
P
O
C
C
O
M
A
R
D
1
F
P C  
C
A R  
D
Z
2
D
E
F
T
L
L
O
A
W
M
N
H
P
1
L
E
N
S
S
H
L
F
I
A
T
M
P
2
R
U
P
I G  
T
S
T
A
R
E T N E  
T
U
S
C
A
P
N
O
W
C
S
E
E
E
R
E
L
C
T
O
N
S
/
M
E
T
A
N
U
N
D
B
3
D
Y
R
E
F
O
R
M
3
D
A
U
T
O
A
D
J
A
U
S
T
9-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Appendix  
z
USB Memory Device or USB Memory Card Reader Support .... 10-2  
x Troubleshooting ......................................................10-3  
c Specifications .........................................................10-5  
v Cabinet Dimensions ...............................................10-7  
b Pin Assignments of D-Sub RGB Input Connector ..10-7  
n Compatible Input Signal List ...................................10-8  
m REMOTE 1 Connector............................................10-9  
, PC Control Codes and Cable Connection ............10-10  
Cable Connection ............................................................................................ 10-10  
PC Control Connector (D-SUB 9P) ................................................................. 10-10  
. Using Software Keyboard .....................................10-10  
⁄ Operation Using an HTTP Browser ......................10-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
z USB Memory Device or USB Memory Card  
Reader Support  
The projector is compatible with either a USB memory device or  
USB memory card reader which supports the viewer and secu-  
rity features.  
• To use a USB memory device or USB memory card reader,  
connect the device to the USB port (type A).  
• Select one of the Drive icons in the Viewer toolbar, Capture  
toolbar and PC Card File setting screen. Up to four drives can  
be accepted.  
• To use a USB memory device as a Protect key for Security  
function, select one from the Drive icons in the Security setting  
screen.  
NOTE:  
•
Some USB memory devices (brands) or USB memory card readers  
may not work.  
•
You cannot use a USB memory device and a USB memory card reader  
when connecting a USB mouse to the projector.  
Using a USB HUB that allows multiple USB memory devices or card  
readers is not supported either.  
Do not do the following while the USB memory device or USB memory  
card reader’s access indicator is lit or flashing (while data is being  
accessed.) Doing so can damage your USB memory device or USB  
memory card in the reader. Back up your data in case it will need to be  
restored.  
•
* Pulling out the USB memory device or USB memory card reader  
from the USB port of the projector.  
* Pulling out the memory card from the USB memory card reader  
* Turning off the main power switch or unplugging the power cable.  
The drive for ”USB 1-4” is displayed only when the USB memory de-  
vice or USB memory card reader is connected to the projector. The  
drive for “USB 1-4” may be displayed differently from the one in the  
USB memory card reader.  
•
•
Some USB memory devices (brands) or USB memory cards cannot  
be used as Protect key for the projector’s Security function.  
10-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
x Troubleshooting  
This section helps you resolve problems you may encounter while setting up or using the projector.  
Power Indicator  
Indicator Condition  
Off  
Projector Condition  
The main power is off  
The projector is getting ready to turn on. Wait for a moment.  
Note  
–
Blinking light  
Green blinking  
0.5 sec ON,  
0.5 sec OFF  
2.5 sec ON,  
0.5 sec OFF  
0.5 sec ON,  
0.5 sec OFF  
2.5 sec ON,  
0.5 sec OFF  
Green blinking  
Orange blinking  
Orange blinking  
Off Timer or Sleep Timer is active.  
The projector is cooling down.  
On Timer is active.  
–
Wait for a moment.  
–
Green  
Steady light  
The projector is turned on.  
–
–
Orange  
The projector is in Standby or Idle.  
Status Indicator  
Indicator Condition  
Off  
Red blinking  
Projector Condition  
Note  
Normal  
–
Blinking light  
1 cycle (0.5 sec ON, Lens hood or lamp cover error  
2.5 sec OFF)  
Replace the lens hood or the lamp cover  
correctly.  
2 cycle (0.5 sec ON, Temperature error  
0.5 sec OFF)  
The projector is overheated. Move the  
projector to a cooler location.  
Power unit will not work correctly.  
3 cycle (0.5 sec ON, Power error  
0.5 sec OFF)  
4 cycle (0.5 sec ON, Fan error  
0.5 sec OFF)  
Cooling fan has stopped. Contact your  
dealer.  
Steady light  
Orange  
Green  
Control key locked  
You have pressed control panel key when  
Control Key Lock is enabled.  
–
Idle condition  
Lamp 1/2 Indicator  
Indicator Condition  
Off  
Red blinking  
Projector Condition  
Note  
–
Light off  
2.5 sec ON,  
Replace the lamp.  
Lamp has reached its end of life. Lamp  
Blinking light  
0.5 sec OFF  
replacement message will be displayed.  
No lamp  
1 cycle (0.5 sec ON,  
2.5 sec OFF)  
Lamp is not installed. Turn off the power  
and install lamp.  
6 cycle (0.5 sec ON,  
0.5 sec OFF)  
Lamp fails to light. Wait a full minute and  
turn on the power again. If this will not  
solve the problem, consult your dealer.  
Fails to read lamp data.  
Lamp error  
7 cycle (0.5 sec ON,  
0.5 sec OFF)  
Lamp data error  
Consult your dealer.  
Wait for a moment.  
Green blinking  
Orange blinking  
Red  
Re-firing the lamp  
Wait for a moment.  
Switching from Lamp 1 to 2  
Lamp has been used beyond its limit. The  
projector will not turn on until the lamp  
is replaced.  
Replace the lamp.  
Steady light  
–
–
Green  
Lamp mode is set to Normal mode  
Lamp mode is set to Eco mode.  
Orange  
10-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
Common Problems & Solutions  
Problem  
Check These Items  
Check that the power cable is plugged in and that the main power switch on the projector is on. See pages 1-  
Does not turn on  
•
9 and 2-11.  
•
•
Ensure that the lens hood or the lamp cover is installed correctly. See pages 1-4 and 9-2.  
Check to see if the projector has overheated or the lamp has reached the end of its usable life. If there is  
insufficient ventilation around the projector or if the room where you’re presenting is particularly warm, move  
the projector to a cooler location.  
No picture  
•
Use the menu or Source/Input button to select your source (RGB 1/2, DVI, Video, S-Video, Viewer or LAN).  
See page 3-3 or 8-7.  
•
•
•
•
•
•
•
•
Ensure your cables are connected properly.  
Use menus to adjust the brightness and contrast. See page 8-8.  
Select correct option in the Signal Select for current signal. See page 8-16.  
Select RGB/Component when connecting DVD player to RGB connector of the projector. See page 8-11.  
Apply a standard RGB signal when using RGB connector.  
Adjust picture for RGB signal.  
Make sure each setting is correct.  
If the problem still persists, reset the settings or adjustments to factory preset levels using the Factory Default  
in the Adjustment Menu. See page 8-13.  
•
•
If Security is enabled, a keyword or PC card as a protect key is required.  
Remove the lens cap.  
Image isn’t square to the  
screen  
•
•
Reposition the projector to improve its angle to the screen. See page 3-3.  
Use the 3DReform function to correct the trapezoid distortion. See page 3-4.  
Picture is blurred  
•
•
•
Adjust the focus. See page 3-4.  
Reposition the projector to improve its angle to the screen. See page 3-3.  
Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page  
2-2.  
•
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.  
Should this happen, let the projector stand until there is no condensation on the lens.  
Image is scrolling verti-  
cally, horizontally or  
both  
•
Use the menus or Source/Input button on the remote control or the cabinet to select the source you want to  
input. See page 3-3 or 8-7.  
Remote control does  
not work  
•
•
•
•
Install new batteries. See page 1-12.  
Make sure there are no obstacles between you and the projector. See page 1-12.  
Stand within 22 feet (7 m) of the projector. See page 1-12.  
Check if one or more remote sensors are enabled. Select [Projector Options] → [Setup] → [Page 5] →  
[Remote Sensor] from the menu. See page 8-17.  
•
•
•
If the remote control cable plug is inserted into the REMOTE 2 IN jack, the remote control does not function  
wirelessly. See page 1-13.  
Make sure that the remote control’s ID corresponds with the projector’s ID. See page 7-2.  
Indicator is lit or blink-  
ing  
See the Power/Status/Lamp Indicator on page 10-3.  
Cross color in RGB  
mode  
•
•
•
If Auto Adjust is off, turn it on or adjust the image manually with the Position/Clock in the Image Options. See  
page 8-16.  
USB mouse does not  
work  
Make sure that your USB mouse is properly connected to the projector.  
The projector may not support some brands of a USB mouse.  
No on-screen menu  
Press MUTE OSD if the image is muted. Or press and hold CTL and press MUTE OSD button. See page 4-2.  
10-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
c Specifications  
This section provides technical information about the GT5000 Projector’s performance.  
Model Number GT5000  
Optical  
LCD Panel  
1.4" p-Si TFT active-matrix with Micro Lens Array, 1024
ן
768 native resolution up to 1600
ן
1200 with  
Advanced AccuBlend Technology  
Lamp  
275 W DC lamp
ן
2  
Lamp Life  
Lens Options  
Eco-mode 2000 hours/Normal mode 1500 hours  
Motorized zoom and Motorized focus  
GT10RLB :F2.4 f=28.9mm  
GT19ZL : F2.0-2.7 f=48.9-63.7mm  
GT13ZLB : F2.3-2.8 f=34.5-42.5mm  
GT20ZL : F1.8-2.5 f=57.4-74.7mm  
GT24ZLB : F2.5-3.2 f=64.0-93.8mm  
GT34ZLB : F2.5-3.3 f=93.5-140.3mm  
Lens Shift  
GT20ZL: Vertical +/- 0.5V, Horizontal +/- 0.32H  
GT13ZLB: Vertical +/-0.32V, Horizontal +/-0.19H  
GT19ZL/GT24ZLB/GT34ZLB: Vertical +/- 0.39V, Horizontal +/- 0.24H  
GT10RLB: 40-250 inches (1016-6350mm) diagonal  
GT20ZL/GT19ZL/GT13ZLB: 40 - 300 inches (1016 - 7620 mm) diagonal  
GT24ZLB: 60 - 400 inches (1524 - 10160 mm) diagonal  
GT34ZLB : 80-500 inches (2032-12700 mm) diagonal  
GT10RLB lens: 0.8 - 5.0 m / 31.5" - 196.9"  
GT13ZLB lens: 1.0 - 9.0 m / 39.37"- 354.3"  
GT19ZL lens: 1.4 - 13.5 m / 55.12"- 531.5"  
GT20ZL lens: 1.7 - 15.8 m / 66.93"- 622"  
Image Size  
Projection Distance  
GT24ZLB lens: 2.6 - 26.4 m / 102.4"- 1039"  
GT34ZLB lens: 5.1 - 49.7 m / 200.8"- 1957"  
Electrical  
Input Connections  
RGB/YCr/Cb/H(HV)V 5 BNC
ן
1, Audio: RCA (L/MONO, R)
ן
1  
RGB  
DVI DIGITAL  
Video  
S-Video  
PC Card  
D-Sub 15 pin
ן
1, Audio: Stereo Mini Audio
ן
1  
DVI-D (Max resolution : XGA@60Hz) x 1, Audio: Stereo Mini Audio
ן
1  
BNC
ן
1, Audio: RCA (L/MONO, R)
ן
1  
Mini DIN 4
ן
1, Audio: RCA (L/MONO, R)
ן
1  
Slot
ן
2  
Option Board  
RGB  
Slot
ן
2  
D-Sub 15 pin
ן
1  
RCA (L/MONO, R)
ן
1  
Stereo mini jack ;IN x 1; OUT
ן
1  
D-Sub 9 pin; IN
ן
1, OUT
ן
1  
D-Sub 15 Din
ן
1  
Stereo mini jack
ן
1  
RJ-45
ן
1  
Output Connections  
Other Input/Output  
Audio Out  
Remote Control  
PC Control  
Ex. Control  
SC. TRIGGER  
LAN Port  
USB Port  
A Type
ן
1, B Type
ן
1  
Input Compatibility  
NTSC / PAL / PAL60 / SECAM / NTSC4.43, YCbCr Component, HDTV-1080I, 1080p, 720p, 480p,  
480I, VGA, SVGA, XGA, SXGA / UXGA (with Advanced AccuBlend)  
Horizontal Frequency : 15 - 100 kHz (RGB : 24 kHz or over)  
Vertical Frequency : 48 - 120 Hz  
Sychronization  
Range  
Video Bandwidth  
Color Reproduction  
Horizontal Resolution  
RGB: 100 MHz  
Full color, 16.7 million colors simultaneously  
550 TV lines : NTSC / PAL / NTSC4.43 / YCbCr  
350 TV lines : SECAM  
RGB: 1024 dots horizontal, 768 dots vertical  
10-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
Built-in Speakers  
Power Requirement  
Input Current  
Power Consumption  
(2 lamps)  
5W
ן
2  
100 - 120VAC / 200 - 240 VAC, 50 / 60 Hz  
8.0 A (100 - 120 VAC) / 4.0A (200 - 240 VAC)  
800W (Lamp Normal mode)  
660W (Lamp Eco mode)  
1W (Standby)  
Mechanical  
Dimensions  
Net Weight  
20.4" (W)
ן
9.5" (H)
ן
21.6" (D) / 518 mm (W)
ן
242 mm (H)
ן
548 mm (D) (not including protrusions)  
40.6 lbs / 18.4 kg (not including lens)  
Environment  
Operational Temperatures: 32˚ - 95˚F (0˚ to 35˚C), 20 - 80% humidity  
Storage Temperatures: 14˚ - 122˚F (-10˚ to 50˚C), 20 - 80% humidity  
UL Approved (UL 60950, CSA 60950)  
Regulations  
Meets DOC Canada Class B requirements  
Meets FCC Class B requirements  
Meets AS/NZS3548 Class B  
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)  
Meets Low Voltage Directive (EN60950, TUV GS Approved)  
For additional information visit:  
US: http://www.necvisualsystems.com  
Europe: http://www.nec-europe.com/  
Global: http://www.nec-pj.com/  
LCD panels are inherently susceptible to pixel defects.  
For additional information regarding pixel data, please contact your local NEC sales office.  
The specifications are subject to change without notice.  
10-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
v Cabinet Dimensions  
P O W E R  
S T A T U S  
A L M P  
2
A L M P  
1
P C C A R D  
D O W N  
2
P C C A R D  
1
O N / S T A N D B Y  
Z O O M  
F O C U S  
S E L E C T  
R I G H T  
L E N S S H I F T L E F T  
A U T O A D J U S T 3 D R E F O R M  
3 D  
A
Z
F
U P  
2 (0.08)  
259 (10.2)  
6 (0.2)  
518 (20.4)  
Lens center  
I
Unit = mm (inch)  
Lens center  
I
R
135 (5.3)  
17 (0.7)  
b Pin Assignments of D-Sub RGB Input Connector  
Mini D-Sub 15 Pin Connector  
Pin No.  
RGB Signal (Analog)  
YCbCr Signal  
5
4
3
2
1
10  
9
8
7
6
1
2
Red  
Cr  
Y
15 14 13 12 11  
Green or Sync on Green  
Blue  
3
Cb  
Signal Level  
4
Ground  
Video signal : 0.7Vp-p (Analog)  
Sync signal : TTL level  
* RGB 2 Input only  
5
Ground  
6
Red Ground  
Cr Ground  
Y Ground  
Cb Ground  
7
Green Ground  
Blue Ground  
8
9
No Connection  
Sync Signal Ground  
SCART Sync  
10  
11  
12  
13  
14  
15  
Sync  
Bi-directional DATA (SDA)*  
Horizontal Sync or Composite Sync  
Vertical Sync  
Data Clock*  
10-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
n Compatible Input Signal List  
Signal  
Resolution  
( Dots )  
–
Frequency H.  
( kHz )  
15.734  
Refresh Rate  
( Hz )  
60  
NTSC  
PAL  
–
15.625  
15.625  
31.47  
31.47  
31.47  
34.97  
35  
50  
SECAM  
VESA  
–
50  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
720 
ן
 350  
720 
ן
 400  
720 
ן
 350  
720 
ן
 400  
800 
ן
 600  
800 
ן
 600  
800 
ן
 600  
800 
ן
 600  
800 
ן
 600  
832 
ן
 624  
1024 
ן
 768  
1024 
ן
 768  
1024 
ן
 768  
1024 
ן
 768  
1024 
ן
 768  
1024 
ן
 768  
1152 
ן
 864  
1152 
ן
 870  
1152 
ן
 900  
1152 
ן
 900  
1280 
ן
 960  
1280 
ן
 1024  
1280 
ן
 1024  
1280 
ן
 1024  
1280 
ן
 1024  
1280 
ן
 1024  
1280 
ן
 1024  
1400 
ן
 1050  
1920 
ן
 1080  
–
59.94  
IBM  
60  
MAC  
60  
MAC  
66.67  
MAC  
66.67  
VESA  
37.86  
37.5  
72.81  
VESA  
75  
IBM  
39.375  
43.269  
31.469  
37.927  
39.44  
39.44  
35.16  
37.879  
48.077  
46.88  
53.674  
49.725  
35.5  
75  
VESA  
85.01  
IBM  
70.09  
VESA  
85.04  
IBM  
87.85  
IBM  
87.85  
VESA  
56.25  
VESA  
60.32  
VESA  
72.19  
VESA  
75  
VESA  
85.06  
MAC  
74.55  
VESA  
43 Interlaced  
VESA  
48.363  
56.476  
60.241  
60.023  
68.677  
67.5  
60  
VESA  
70.07  
MAC  
74.93  
VESA  
75.03  
VESA  
85  
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
VESA  
75  
MAC  
68.681  
61.796  
71.736  
60  
75.06  
SUN  
65.95  
SGI  
76.05  
VESA  
60  
VESA  
63.981  
69.89  
78.125  
81.13  
79.976  
91.146  
–
60.02  
MAC  
65.2  
HP  
72.01  
SUN  
76.11  
VESA  
75.03  
VESA  
85.02  
SXGA+  
HDTV (1080p)  
SDTV(576i)(625i)  
SDTV(576p)(625p)  
HDTV (1080i)(1125i)  
HDTV (1080i)(1125i)  
HDTV (720p)(750p)  
SDTV (480p)(525p)  
VESA  
–
67.5  
60  
15.6  
50  
–
31.5  
50  
1920 
ן
 1080  
1920 
ן
 1080  
1280 
ן
 720  
–
33.75  
28.13  
45  
60 Interlace  
50 Interlace  
60 Progressive  
59.94 Progressive  
60  
31.47  
75.0  
1600 
ן
 1200  
1600 
ן
 1200  
1600 
ן
 1200  
1600 
ן
 1200  
–
VESA  
81.3  
65  
VESA  
87.5  
70  
VESA  
93.75  
15.734  
15.625  
75  
DVD YCbCr  
DVD YCbCr  
59.94 Interlaced  
50 Interlaced  
–
#: Images in above flagged with # are compressed with Advanced AccuBlend.  
NOTE: Some composite sync signals may not be displayed correctly.  
Signals other than those specified in the table above may not be displayed correctly. If this should happen, change  
the refresh rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.  
UXGA (1600
ן
1200) is supported for separate sync signal only.  
10-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
m REMOTE 1 Connector  
5
4
3
2
1
10  
9
8
7
6
15 14 13 12 11  
This connector is used for a third party external control device.  
Pin No.  
FUNCTION  
SHORT/OPEN  
14  
External control mode ON  
External control mode OFF  
SHORT  
OPEN  
5
POWER ON  
POWER OFF  
SHORT  
OPEN  
10  
PICTURE MUTE ON  
PICTURE MUTE OFF  
SHORT  
OPEN  
3
MUTE SOUND ON  
MUTE SOUND OFF  
SHORT  
OPEN  
12pin  
OPEN  
8pin  
OPEN  
OPEN  
SHORT  
OPEN  
OPEN  
SHORT  
SHORT  
OPEN  
OPEN  
SHORT  
OPEN  
OPEN  
SHORT  
4pin  
11pin  
OPEN  
4,8,12,11  
OPEN  
RGB 1  
OPEN  
SHORT  
OPEN  
VIDEO  
OPEN  
OPEN  
S-VIDEO  
Slot 1-1  
OPEN  
SHORT  
SHORT  
SHORT  
SHORT  
OPEN  
OPEN  
OPEN  
RGB 2  
SHORT  
OPEN  
OPEN  
Slot 1-2  
OPEN  
SHORT  
OPEN  
RGB1 (S-VIDEO)  
DVI (DIGITAL)  
VIEWER  
RGB1 (VIDEO)  
Slot 2-1  
OPEN  
SHORT  
SHORT  
SHORT  
SHORT  
SHORT  
SHORT  
OPEN  
SHORT  
SHORT  
OPEN  
OPEN  
SHORT  
SHORT  
SHORT  
SHORT  
OPEN  
Slot 2-2  
LAN  
*
When combinations other than specified in the above table are selected or when no optional board is inserted in the Slot 1  
and 2, the input will be switched to RGB 1 by default.  
*
*
The term “SHORT” means to connect with pin 15  
When in the external control mode, the POWER, Source/Input, PICTURE MUTE and SOUND MUTE buttons on the remote  
control will not function.  
*
When the External control mode is set to ON, the following settings are not effective: Source Select, Auto Start, Power  
Management, Power off Confirmation, Idle mode, Default Source Select, Timer and Test Pattern.  
NOTE: When turning off the power to the projector using the external control, do not disconnect the plug from the power outlet. These  
procedures are to protect your projector and the connected equipment.  
10-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
, PC Control Codes and Cable Connection . Using Software Keyboard  
PC Control Codes  
Function  
Code Data  
POWER ON  
02H 00H 00H 00H 00H 02H  
POWER OFF  
02H 01H 00H 00H 00H 03H  
INPUT SELECT RGB 1  
INPUT SELECT RGB 2  
INPUT SELECT VIDEO  
INPUT SELECT S-VIDEO  
02H 03H 00H 00H 02H 01H 01H 09H  
02H 03H 00H 00H 02H 01H 02H 0AH  
02H 03H 00H 00H 02H 01H 06H 0EH  
02H 03H 00H 00H 02H 01H 0BH 13H  
INPUT SELECT DVI (DIGITAL) 02H 03H 00H 00H 02H 01H 1AH 22H  
INPUT SELECT VIEWER  
LAN  
02H 03H 00H 00H 02H 01H 1FH 27H  
02H 03H 00H 00H 02H 01H 20H 28H  
02H 03H 00H 00H 02H 01H 24H 2CH  
02H 03H 00H 00H 02H 01H 25H 2DH  
02H 03H 00H 00H 02H 01H 29H 31H  
02H 03H 00H 00H 02H 01H 2AH 32H  
02H 03H 00H 00H 02H 01H 07H 0FH  
02H 03H 00H 00H 02H 01H 0CH 14H  
02H 10H 00H 00H 00H 12H  
SLOT1-1  
SLOT1-2  
SLOT2-1  
SLOT2-2  
1 to 0 and Characters  
RGB1(VIDEO)  
........................Use to type in IP address or projector name  
RGB1(S-VIDEO)  
PICTURE MUTE ON  
PICTURE MUTE OFF  
SOUND MUTE ON  
SOUND MUTE OFF  
ON SCREEN MUTE ON  
ON SCREEN MUTE OFF  
MODE .............Selects one of three modes for alphabet and spe-  
cial characters.  
02H 11H 00H 00H 00H 13H  
02H 12H 00H 00H 00H 14H  
SP ...................Inserts a space  
02H 13H 00H 00H 00H 15H  
BS ...................Deletes one character backward  
̇ .....................Returns to the previous  
̈ .....................Advances to the next  
OK ...................Executes the selection  
Cancel .............Cancels the selection  
02H 14H 00H 00H 00H 16H  
02H 15H 00H 00H 00H 17H  
NOTE: Contact your local dealer for a full list of PC Control Codes if needed.  
Cable Connection  
Communication Protocol  
Baud rate ........................ 38400 bps  
Data length ..................... 8 bits  
Parity .............................. No parity  
Stop bit ........................... One bit  
X on/off ........................... None  
Communications procedure Full duplex  
NOTE: Depending on the equipment, a lower baud rate may be recommended for  
long cable runs.  
PC Control Connector (D-SUB 9P)  
To TxD of PC  
To RxD of PC  
To GND of PC  
1
2
3
4
5
6
7
8
9
To RTS of PC  
To CTS of PC  
NOTE: Pins 1, 4, 6 and 9 are no used.  
NOTE: Jumper “Request to Send” and “Clear to Send” together on both ends of the  
cable to simplify cable connection.  
10-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
Structure of the HTTP Server  
⁄ Operation Using an HTTP Browser  
Overview  
The use of HTTP server functions will allow control of the projec-  
tor from a web browser without the installation of special soft-  
ware. Please be sure to use “Microsoft Internet Explorer 4.x” or a  
higher version for the web browser.(This device uses “JavaScript”  
and “Cookies” and the browser should be set to accept these  
functions.The setting method will vary depending on the version  
of browser. Please refer to the help files and the other informa-  
tion provided in your software.)  
NOTE:  
* The use of HTTP server functions is not available during Standby mode.  
* The display’s or button’s response can be slowed down or operation may not be  
accepted depending the settings of your network. Should this happen, consult  
your network administrator.  
* The projector may not respond if its buttons are repeatedly pressed in rapid  
intervals. Should this happen, wait a moment and repeat. If you still can’t get any  
response, pull out and then re-insert the LAN card.  
* Do not use the HTTP Server functions and the Dynamic Image Utility included on  
the supplied CD-ROM. Using both at the same time may result in a connection  
failure or slow response.  
Power: This controls the power of the projector.  
On ...............Power is switched on.  
Access is gained to the HTTP server functions by specifying  
http:// <the projector’s IP address> /index.html  
in the entry column of the URL.  
Off ...............Power is switched off.  
Volume: This controls the volume of the projector.  
̆ .................Increments the volume adjustment value.  
Preparation Before Use  
Make network connections and set up the projector and confirm  
that it is complete before engaging in browser operations. (See  
“LAN Mode” on page 8-19.)  
̄ .................Decrements the volume adjustment value.  
Mute: This controls the mute function of the projector.  
All On ..........Mutes each of the video, audio, and on-screen  
display functions.  
Operation with a browser that uses a proxy server may not be  
possible depending on the type of proxy server and the setting  
method. Although the type of proxy server will be a factor, it is  
possible that items that have actually been set will not be dis-  
played depending on the effectiveness of the cache, and the con-  
tents set from the browser may not be reflected in operation. It is  
recommended that a proxy server not be used unless it is un-  
avoidable.  
All Off ..........Cancels the muting of each of the video, audio,  
and on-screen display functions.  
Picture On ...Mutes the video.  
Picture Off ...Cancels the video muting.  
Sound On ....Mutes the audio.  
Sound Off ....Cancels the audio muting.  
OSD On....... Mutes the on-screen display.  
OSD Off....... Cancels the muting of the on-screen display.  
Handling of the Address for Operation via a Browser  
Regarding the actual address that is entered for the address or  
entered to the URL column when operation of the projector is via  
a browser, the host name can be used as it is when the host  
name corresponding to the IP address of the projector has been  
registered to the domain name server by a network administra-  
tor, or the host name corresponding to the IP address of the pro-  
jector has been set in the “HOSTS” file of the computer being  
used.  
Picture: Controls the video adjustment of the projector.  
Brightness ̆ Increments the brightness adjustment value.  
Brightness ̄ Decrements the brightness adjustment value.  
Contrast ̆ ...Increments the contrast adjustment value.  
Contrast ̄ ...Decrements the contrast adjustment value.  
Color ̆ ........Increments the color adjustment value.  
Color ̄ ........Decrements the color adjustment value.  
Hue ̆ ..........Increments the hue adjustment value.  
Hue ̄ ..........Decrements the hue adjustment value.  
Sharpness ̆Increments the sharpness adjustment value.  
Sharpness ̄Decrements the sharpness adjustment value.  
Example 1: When the host name of the projector has been set to  
“pj.nec.co.jp”, http://pj.nec.co.jp/index.html is specified for the  
address or the entry column of the URL.  
Example 2: When the IP address of the projector is  
“192.168.73.1”, access is gained to the HTTP server func-  
tions by specifying  
http://192.168.73.1/index.html for the address or the entry  
column of the URL.  
*
The functions that can be controlled will vary depending on the signal  
being input to the projector.  
10-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Appendix  
Source Select:This switches the input connector of the projector.  
RGB1 ...................... Switches to the RGB 1 connector.  
RGB2 ...................... Switches to the RGB 2 connector.  
DVI(DIGITAL)........... Switches to the DVI connector.  
Video ....................... Switches to the Video connector.  
S-Video ................... Switches to the S-Video connector.  
Viewer ..................... Switches to the Viewer.  
LAN ......................... Switches to a LAN signal.  
Slot 1-1 .................... Switches to input 1 of the Slot 1.  
Slot 1-2 .................... Switches to input 2 of the Slot 1.  
Slot 2-1 .................... Switches to input 1 of the Slot 2.  
Slot 2-2 .................... Switches to input 2 of the Slot 2.  
RGB1 (VIDEO) ........ Switches to Video of the RGB1 connec-  
tor.  
RGB1 (S-VIDEO) .... Switches to S-Video of the RGB1 con-  
nector.  
Projector Status: This displays the condition of the projector.  
Remaining Lamp 1/2 Time  
................................ Displays the remaining life of the lamp  
1/2 as a percentage.  
Lamp 1/2 Hour Meter ...Displays how many hours the lamp 1/2  
has been used.  
Projector Usage ...... Displays how many hours the projector  
has been used.  
Filter Usage ............. Displays how many hours the filter has  
been used.  
Error Status ............. Displays the status of errors occurring  
within the projector.  
Refresh.................... Updates the display of the following con-  
ditions.  
10-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  

MTD Lawn Mower 110 500 User Manual
Napoleon Grills Gas Grill MIRAGE 485 User Manual
NEC Projector MT 1020 User Manual
NETGEAR Modem WN3100RP User Manual
Nokia Carrying Case LPS 4 User Manual
Panasonic Camcorder AG DVC60 E User Manual
Panasonic CRT Television CT 20R13 User Manual
Panasonic Fax Machine KX PW30CL User Manual
Panasonic GPS Receiver CN GP50N User Manual
Panasonic Printer KX P7100 User Manual