MD3196 & MD3091
Shown with the
MA3090 Harness Assembly
COMPACT TACTICAL LIFE PRESERVERS
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Introduction........................................................................................................1
Product Familiarization and Readiness ............................................................2
MD3196 ................................................................................................2
MD3091 ................................................................................................3
Prior to Use ..........................................................................................3
Readiness Checklist (MD3196 & MD3091)........................................................3
Wearing ..............................................................................................................4
Inflating ..............................................................................................................4
Manual Inflation..................................................................................4
Auto-Inflation – MD3196 ....................................................................4
Oral Inflation .......................................................................................5
Deflating.............................................................................................................5
Re-arming the MD3196 .....................................................................................6
Re-arming the MD3091 .....................................................................................7
Repacking ...........................................................................................................8
Folding..................................................................................................8
Closing Zipper 1 – Long Zipper...........................................................9
Closing Zipper 2 – Short Zipper..........................................................9
Stowing the Manual Conversion Cap (MD3196 Only) ......................9
Integrating Pouch Attachment Ladder System and MOLLE Vest .................10
Quick-Release Features .....................................................................11
Attaching the MA3090 Harness......................................................................11
Auto/Manual Conversion.................................................................................12
Care and Maintenance ....................................................................................13
Testing for Leaks................................................................................14
Testing the Oral Inflation Valve........................................................14
General Tests and Inspections...........................................................14
Testing the Manual Inflator..............................................................15
Testing the Automatic Inflator .........................................................15
Cleaning and Storage ......................................................................................16
Accessories........................................................................................................16
Glossary.............................................................................................................16
ii
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
This manual provides instructions and guidelines for safely using and
maintaining Mustang Survival MD3196 and MD3091 Compact Tactical Life
Preservers (LPs).
Mustang Survival LPs have been designed specifically for easy integration
with body armor and tactical vests, including armor and vests using a
Modular Lightweight Load-carrying Equipment (MOLLE) webbing system.
The compact design of the LPs provides individuals wearing body armor
with flotation capability with minimal bulk and minimal interference.
In-water performance tests with the LPs attached to a typical body armor
vest successfully demonstrate the ability of the LPs to self-right and provide
effective flotation and buoyancy.
Due to variances in local configuration, full gear in-water testing is
recommended to validate performance.
The MD3196 and MD3091 LPs can be worn as stand-alone life preservers
when used in conjunction with the MA3090 harness assembly.
The MD3196 LP inflates automatically upon submersion using a hydrostatic
inflator that significantly reduces the potential for accidental inflation due
to humidity, sea spray, or wet storage. The hydrostatic inflator must be
submerged to automatically activate.
The MD3196 LP may be inflated manually, prior to submersion, by pulling
the beaded manual inflation handle.
The MD3091 LP is inflated manually by pulling the beaded manual inflation
handle.
When worn, used, and serviced according to the instructions in this manual,
Mustang Survival MD3196 and MD3091 LPs can greatly increase a user's
chance of survival in the water.
1
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT FAMILIARIZATION AND READINESS
MD3196
Figure 1 shows the left lobe (as worn) of the MD3196 LP with the oral
inflator tube assembly-A, and the right lobe of the LP with the manual/
automatic inflator assembly-B and the orange whistle-C.
To determine the
FiGURE 1
FiGURE 2
operational status of the
inflator examine the status
indicator through access
point A as shown in Figure
2:
A
C
B
•
Green indicates the
inflator is armed and
the LP is ready for use.
A
•
Red indicates the inflator has been fired and must be re-armed before
the LP can be used – see Re-arming.
To become more familiar with the LP components:
1. Open both zippers completely, and place the LP on a smooth, flat
surface with the oral tube facing the user.
2. Ensure the oral inflator dust cap is in the
stowed position (Figure 3).
3. Visually inspect the expiry date on the inflator
(Figure 4). If the expiry date has passed,
replace the inflator – see Re-arming.
Dust Cap:
Stowed
Dust Cap:
Deꢀate
NOTE: If the expiry date has passed, Mustang
Survival recommends water testing the LP to
become familiar with LP functionality.
FiGURE 3
4. Repack the LP – see Repacking.
Hydrostatic Water
Inlet Valve
Black Locking Ring
Tabs
Status
Indicator
Manual Inꢀation
Lanyard
Expiry Date
FiGURE 4
Beaded Manual
Inꢀation Handle
2
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
MD3091
FiGURE 5
The left lobe (as worn) of the MD3091 LP
contains the oral inflator tube assembly-A.
The right lobe of the LP contains the manual
inflator assembly-B and the orange whistle-C. .
A
C
B
To become more familiar with the LP
components:
1. Open both zippers completely, and place
the LP on a smooth, flat surface with the
inflator facing the user.
FiGURE 6
CO2 Cylinder
2. Ensure the oral inflator dust cap is in the
stowed position.
Inꢀator Mechanism
Up-and-Ready
Status Pin
3. Ensure the status pin and the CO cylinder
2
are intact, and the lever is in the up and
ready position (Figure 6).
Inꢀation Lanyard
Beaded Manual
Inꢀation Handle
4. If the cylinder is not intact, and/or if the
status pin is missing or broken, re-arm the
cylinder and replace the status pin – see
Re-arming (Figure 7).
FiGURE 7
Piercing Pin
5. Repack the LP – see Repacking.
Status Pin
Prior to Use
Visually inspect the LP prior to use to:
Inflation Lever
•
•
ensure the LP is properly armed
ensure the LP is free of rips, tears, or holes and all seams are securely
sewn
•
ensure the fabric, straps, and hardware are free from any defects
READINESS CHECKLIST (MD3196 & MD3091)
When all applicable boxes are checked, the LP is ready for use:
F
F
F
F
F
F
F
Beaded manual inflation handle is fastened.
No rips, tears, or holes, and all seams securely sewn.
Fabric, straps, and hardware free from defects.
All zippers, Velcro™, and chest buckle securely fastened.
MD3196 only: Status indicator is green.
MD3196 only: Inflator expiry date has not passed.
MD3091 only: Status pin and cylinder intact, and manual inflation lever
in the up and ready position.
NOTE: If there are any concerns about the readiness of the MD3196 or
MD3091, contact the Mustang Survival dealer.
3
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
WEARING
NOTE: The LP provides 35 lbs of flotation, and is designed for users
weighing more than 80 lbs and with a chest size of 30-52 inches.
The LP must be properly adjusted to fit the individual wearing it. Incorrect
fit, or improper fastening of attachments can impede LP effectiveness.
•
To avoid injury to the user or damage to the LP, the LP should never be
worn under clothing or anything else that could restrict inflation.
•
Belts and straps should be adjusted for secure, comfortable fit. When
the LP is integrated with MOLLE webbing system and body armor vest,
ensure all connections are securely fastened – see Integrating PALS with
a MOLLE Vest.
•
When the LP is used in conjunction with the MA3090 harness assembly,
the waist belt should fit securely – see Attaching the MA3090 Harness.
INFLATING
WARNING: The MD3091 LP must be manually activated by the user; it
does not automatically inflate upon submersion.
NOTE: When using the MD3196 LP in temperatures below freezing, fully
discharging the CO cylinder may not provide adequate inflation; use the
2
oral inflator to top-up the LP.
Manual Inflation
Manually activate the inflation mechanism for either LP by jerking firmly
downward on the beaded manual inflation handle. The LP should fully
inflate within five seconds.
Auto-Inflation – MD3196
CAUTION: If the MD3196 LP has been manually inflated, CO inflation
2
could over-pressurize and damage it.
When the inflator is submerged more than approximately four inches in
water the hydrostatic water inlet valve opens letting water contact the
water-sensitive element. The element releases a stainless steel coil spring,
driving a needle into the end of the gas cylinder, puncturing it and allowing
the gas to fill the LP. The LP should fully inflate within five seconds.
Special Considerations
Auto-inflation of the MD3196 LP could create a risk of damage under the
following circumstances:
•
•
•
Double inflation – CO cylinder inflation after full oral inflation.
2
Inflation while stored in a tight space.
Inflation while in an awkward place or position.
4
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Oral Inflation
A properly armed LP will inflate correctly. However, when top-up inflation,
or total inflation in a non-emergency situation is required, the LP can be
inflated by mouth.
When fully inflated automatically the carbon dioxide (CO gas) used to
2
auto-inflate the LP slowly escapes through the fabric over time. A slight
reduction of pressure is apparent several hours after inflation. Therefore,
oral top-up inflation may be required during prolonged immersion. To
orally inflate the LP:
1. Disengage both zippers completely and open the left lobe of the LP.
2. Locate the oral inflator tube, and remove the dust cap from the end of
the tube.
3. Blow into the tube until the LP is fully inflated.
4. Replace the dust cap in the stowed position.
DEFLATING
CAUTION: Deflating the LP by any means other than by inverting the oral
inflator dust cap may damage the oral inflator valve.
1. To deflate the LP, remove the oral inflator
dust cap from the oral inflator tube, reverse
the dust cap and reinsert it into the tube.
The dust cap does not lock and must be
held in place (Figure 8).
2. Gently squeeze the LP until fully deflated,
ensuring all air or gas is removed from the
LP. To avoid damage, do not wring or twist
FiGURE 8
the LP or the cell.
3. Replace the dust cap in the stowed position.
4. Visually inspect the inflator status. The status indicator on the MD3196
LP must be green, and the status pin on the MD3091 LP must be in
place before repacking the LP. If those conditions are not met, the LP
inflator has been fired and must be re-armed – see Re-arming.
5. Repack the LP – see Repacking.
5
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
RE-ARMING THE MD3196
CAUTION: The LP must be deflated before being re-armed.
NOTE: An MA7214-10 re-arming kit is required for this procedure.
1. Open both
FiGURE 10
FiGURE 9
zippers, wipe
off any water,
and place the
LP on a smooth,
flat surface with
the inflator
facing the user.
2. Reach under
FiGURE 11
the cover and carefully pull the manual/
automatic inflator assembly out from under
the cover fabric.
Center
Shaft
Status
Indicator
3. Hold the CO cylinder through the fabric,
2
insert the metal key between the black
locking ring and inflator cap, and turn the
key counter-clockwise (Figure 9).
Sealing
Ring
4. Turn the black locking ring counter-
clockwise, and lift off (and discard) the
yellow inflator cap (Figure 10).
FiGURE 12
Center
Shaft
5. Elongate the sealing ring by squeezing it,
and remove (and discard) the inflator body
through the ring (Figure 11).
Status
Indicator
6. Visually Inspect the sealing ring for cracks,
debris, or other damage. If damage is
present, remove the LP from active service
for further assessment.
Sealing
Ring
7. Ensure that the status indicator on the new inflator body is green, and
the expiry date has not passed (Figure 12). If the status indicator is red,
or the expiry date has passed, acquire a new inflator body.
CAUTION: Do not turn the small center shaft of the inflator body.
8. Insert the new inflator body, with the CO
cylinder pointing upward, inside the LP
2
FiGURE 13
(Figure 12), and let the sealing ring rest on
the adapter around the four lugs.
9. Hold the CO cylinder through the fabric
2
of the LP, and position the new inflator
cap with the valve pointing to the right
ensuring the cap is properly seated on the
inflator body and sealing ring (Figure 13).
6
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
10. While pressing firmly onto the inflator
body, turn the black locking ring
clockwise to the locked position, and
pull on the inflator cap to ensure
it is locked onto the inflator body
(Figure 14).
Hydrostatic Water
Inlet Valve
FiGURE 14
Black Locking Ring
Tabs
11. Ensure that the status indicator on the
new inflator cap is green, the pull-
to-inflate lanyard is present, and the
locking ring is locked.
Status
Manual Inꢀation
Lanyard
Indicator
Expiry Date
12. To test for leakage, inflate the LP
using the oral inflator tube – see Inflating. To avoid damage to the LP
do not use a compressor (the maximum pressure should not exceed 2
psi). After two hours there should be no noticeable drop in pressure in
the LP.
13. Deflate and repack the LP – see Deflating, and Repacking.
RE-ARMING THE MD3091
CAUTION: The LP must be deflated before being re-armed.
NOTE: An MA7170 re-arming kit is required for this procedure.
CAUTION: Follow the steps below in the exact sequence described.
1. Unscrew and discard the CO cylinder (Figure 15).
2
2. Ensure the manual lever is in the up and ready position and the manual
inflator mechanism status pin is properly
installed. If missing or damaged, replace the
status pin (Figure 15).
CO2 Cylinder
Inꢀator Mechanism
3. To install the new CO cylinder, screw it into
2
the top of the inflator and hand-tighten. To
avoid damage to the internal gasket, do not
over-tighten (Figure 15).
Up-and-Ready
Status Pin
Inꢀation Lanyard
Beaded Manual
Inꢀation Handle
4. To test for leakage, inflate the LP using the
oral inflator tube – see Inflating. To avoid
damage to the LP do not use a compressor
(the maximum pressure should not exceed
2 psi). After two hours there should be no
noticeable drop in pressure in the LP.
FiGURE 15
5. Deflate and repack the LP – see Deflating, and Repacking.
7
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
REPACKING
WARNING: After each field use inflation, LPs must be rearmed, leak tested,
and fully deflated before repacking - see Re-arming, and Deflating.
Folding
FiGURE 18
FiGURE 17
FiGURE 16
B
C
A
A
1. Lay the LP flat on a clean surface, inflation cell up, and fold the bottom
portion-A of each side of the inflation cell up (Figure 16).
2. Fold side-B over along the full length of the dotted line (Figure 17).
3. Fold side-C over side-B (Figure 18).
FiGURE 20
FiGURE 19
F
E
D
FiGURE 21
4. Fold side-D over along the full length of the
dotted line (Figure 19).
G
5. Fold side-E over side-D (Figure 20).
6. Fold over the top side-F (Figure 21) and
cover-G (Figure 22).
Continued on the next page.
FiGURE 22
8
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Closing Zipper 1 – Long Zipper
NOTE: Mustang Survival uses advanced SecureZip™ 2-step zippers.
1. Reset zipper 1
by pulling zipper
pull-H around
the top of the LP
to Velcro™ tab-I
I
H
(Figure 23).
I
2. Close zipper 1
by pulling zipper
H
FiGURE 24
FiGURE 23
pull-H back to the
beginning of the
zipper tape end, and fasten Velcro™ tabs-I to keep the zipper closed
(Figure 24).
CAUTION: Ensure the inflation cell does not get caught in the zipper.
Closing Zipper 2 – Short Zipper
1. Reset zipper 2
by pulling zipper
pull-J to Velcro™
tab-I (Figure 25).
FiGURE 25
FiGURE 26
I
I
2. Close zipper 2
by pulling zipper
pull-J back to the
beginning of the
zipper tape end
(Figure 26).
J
J
CAUTION: Ensure the inflation cell does not get caught in the zipper.
3. Push the zipper tape ends into the openings at the bottom of the
packed LP, and fasten the beaded manual inflation handle to the LP.
Stowing the Manual Conversion Cap (MD3196 Only)
An interior pocket is provided for stowing a
FiGURE 27
manual conversion cap (MA7219) (Figure 27).
If used, the cap should be attached by lanyard
through the eyelet located within the front
slash entry (see AUTO/MANUAL CONVERSION).
When repacking, tuck the cap into the pocket
(Figure 27) located below the inflator and inside
the front slash entry. Close the front slash entry
with the hook and loop tape over the inflator.
9
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INTEGRATING POUCH ATTACHMENT LADDER
SYSTEM AND MOLLE VEST
WARNING: Suitable anchor points must be used as outlined below.
The LP is intended to be secured to a MOLLE vest using the provided
buckles. The attachment points secure the LP to the front and back of the
MOLLE vest.
The female buckle is designed to mount to the MOLLE vest allowing easy
removal of the LP to reconfigure for different mission profiles and allow
proper operation of breakaway vests. Ensure the attachment points are
accessible, do not interfere with other mounted equipment, and provide a
secure fit ensuring the LP is attached as close to the torso as possible.
FiGURE 29
FiGURE 30
FiGURE 28
1. Lay the MOLLE vest down on a clean flat surface with the back of the
vest facing up.
2. Lift up the emergency extraction strap or other anchor point on the
back of the vest. Loop the back attachment of the MD3196 LP around
the extraction strap or, if no extraction strap is available, around the
PALS webbing (Figure 28).
3. Use the buckle to secure and tighten the back attachment strap. The
collar of the LP should be located near the neckline (Figure 29).
4. With the LP attached, turn the vest over and lay it flat, with the front
of the vest facing up.
5. Position the two front lobes of the LP perpendicular to the webbing
across the vest (Figure 30).
WARNING: For optimal flotation, the LP must be secured tightly
against the vest.
6. On the left-hand side of the vest, feed the female buckle attachment
webbing under a row of Pouch Attachment Ladder System (PALS)
webbing.
7. Insert the female buckle under the upper row of vest webbing
(Figure 31A).
10
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Pull the buckle attachment webbing
through the vest webbing. (Figure 31B).
9. Pass the female buckle through the buckle
attachment webbing (Figure 31C) leaving
the female buckle clip flush with the vest
(Figure 31D).
FiGURE 31A
FiGURE 31B
FiGURE 31D
10. Repeat steps 7-9 on the right-hand side of
the vest.
FiGURE 31C
FiGURE 32
11. Clip the left-hand male buckle (attached to
the LP) into the female buckle attachment
(attached to the vest), (Figure 32). Repeat
on the right-hand side of the vest.
12. Fasten the buckle that connects the left-
and right-hand lobes in front of the chest
section of the vest (Figure 33). Cinch by
pulling on the loose end of the webbing.
13. Ensure all buckles are securely fastened
under the webbing, and all webbing
adjustments are tight.
FiGURE 33
14. Secure excess webbing with Velcro™ straps
Quick-Release Features
NOTE: Found on some body armor (for example, IOTV).
1. Release the LP by pressing the side release buckles below each side of
the LP and the chest buckle. This will completely release the LP from the
front of the MOLLE vest.
2. Using the appropriate release mechanism, release the vest so it can be
removed.
ATTACHING THE MA3090 HARNESS
1. Lay out the MA3090 harness assembly as shown (Figure 34):
•
•
•
•
•
A. T-tab junction buckle
B. Right-hand buckle (as worn)
C. Left-hand buckle (as worn)
D. Looploc
E. Crotch strap buckle
11
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Insert the short side of the webbing
attachment on the back of the MD3196 LP
through Looploc D on the back strap of the
chest belt accessory. Securely fasten the snap.
A
B
D
3. Locate the T-tab junction buckle at the top
of the crotch strap and thread through the
lower back chest belt loop D. Secure the
T-tab with the snap, and turn the snapped
portion so it is positioned inside the chest
belt loop away from the body (Figure 34).
C
E
4. Attach male buckle C to the corresponding
female buckle on the left side of the chest
belt (Figure 35).
FiGURE 34
5. Repeat step 4 on the right side of the chest
belt (Figure 36).
6. Unfasten the crotch strap
FiGURE 35
FiGURE 36
buckle E, and put the LP
on as shown (Figure 37).
7. Buckle the chest buckle
connecting the left- and
right-hand lobes of the LP
(Figure 38).
8. Buckle the waist belt
(Figure 38).
9. Bring the crotch strap
FiGURE 37
buckle to the front
FiGURE 38
between the legs and
securely buckle it to the
chest strap (Figure 38).
A
B
C
AUTO/MANUAL CONVERSION
Under special circumstances, such as wading or at other times when
complete manual control of inflation of the LP is required, the MD3196 LP
can be converted from manual/automatic inflation to manual-only inflation.
The LP may be changed back to manual/automatic inflation by removing
the conversion cap.
NOTE: This procedure requires an armed MD3196 LP and an MA7219
conversion cap.
12
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Tie the conversion cap lanyard through the
eyelet located within the front slash entry
(Figure 39). Allow enough length such that
the manual cap can be stowed in the interior
pocket located below the inflator inside the
slash entry (Figure 39).
FiGURE 39
2. Position the conversion cap over the hydrostatic
water inlet valve (Figure 40).
3. Secure the conversion
cap to the hydrostatic
water inlet by
applying pressure to
the cap at the metal
clip until it locks in
place (Figure 41).
FiGURE 40
FiGURE 41
Reversing the Conversion
1. To remove the conversion cap, open the front slash
entry.
FiGURE 42
2. Reach above the inflator to find the conversion cap
lanyard. Follow the lanyard to the conversion cap.
3. Push the fabric of the slash entry behind the water
inlet valve (Figure 42).
4. Firmly pull the conversion cap lanyard horizontally
across the chest.
5. Place the conversion cap in the manual conversion
cap pocket located inside the front slash entry
when not in use.
6. Visually confirm the conversion cap has been removed from the valve
opening.
CARE AND MAINTENANCE
Before each use, review the Readiness Checklist.
CAUTION: After each inflation, re-arm the LP – see Re-arming.
After each use, deflate, re-arm, and repack the LP – see:
•
•
•
Deflating
Re-arming
Repacking
Visually inspect the LP prior to use to ensure:
•
LP is properly armed
13
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
LP is free of rips, tears, or holes
LP seams are securely sewn
LP fabric, straps, and hardware are free from any defects
Perform the following tests every 180 days, or more frequently if exposed to
potential damage or used in extreme conditions.
Testing for Leaks
1. Orally inflate the LP until it is firm to the touch, and let it stand for two
hours—a leaking LP will not hold its firmness.
2. If the LP is leaking, take it to a service department for evaluation and/
or servicing.
Testing the Oral Inflation Valve
1. Fully inflate the LP using the oral inflator, then hold the valve under
water.
2. If bubbles appear, deflate and retest. If the leak persists, take the LP to
a Mustang dealer for evaluation and/or servicing.
CAUTION: To avoid accidental inflation, do not allow water to contact the
hydrostatic inflator.
General Tests and Inspections
Record the following tests in permanent ink in the Date Maintained column
on the Care and Storage label.
After each test or inspection, repack the LP – see Repacking.
Perform the following tests and inspections annually, after each inflation, or
whenever the integrity of the LP is in doubt.
•
Visually inspect all components for dirt or corrosion, and clean or
replace as necessary – see Readiness Checklist.
•
Visually inspect the LP for damage or excessive abrasion, wear, fabric
tears, or contamination. Particular attention must be paid to the
stitching, straps, and hardware.
•
•
•
Test for leaks.
Test the oral inflation valve.
On the MD3196, ensure the inflator expiry date has not passed. If it has,
replace the inflator – see Re-arming.
•
Ensure the status indicator is green – see Product Familiarization.
14
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing the Manual Inflator
NOTE: A fully armed LP and an approved re-arming kit are required for this
test.
1. Don either LP and manually inflate it by jerking firmly downward on
the beaded manual inflation handle. The LP should fully inflate within
five seconds.
2. Enter water of an appropriate depth to keep the head above the
surface.
3. Ensure the LP floats the user in a prone position, or just slightly back
of vertical in a relaxed position with the mouth well above the surface
of the water, and experiment with different leg positions to become
familiar with changes in buoyancy and/or flotation characteristics.
4. Exit the water, remove the LP, and completely deflate it – see Deflating.
5. Let the LP dry thoroughly, then re-arm and repack it – see Re-arming,
and Repacking.
Testing the Automatic Inflator
NOTE: a fully armed MD3196 LP is required for this test.
1. Don the MD3196.
2. Enter water of an appropriate depth to keep the head above the
surface.
3. When the inflator is submerged under approximately four inches
of water, the MD3196 should fully inflate automatically within five
seconds.
4. Ensure the LP floats the user in a prone position, or just slightly back
of vertical in a relaxed position with the mouth well above the surface
of the water, and experiment with different leg positions to become
familiar with changes in buoyancy and/or flotation characteristics.
5. Exit the water, remove the MD3196.
6. Completely deflate the MD3196 – see Deflating.
7. Let the MD3196 dry thoroughly, then re-arm and repack it – see
Re-arming, and Repacking.
WARNING: If in doubt about the self inspection and servicing of the LP in
accordance with these instructions, or of any test or inspection results,
take the LP in for professional servicing.
15
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING AND STORAGE
NOTE: To avoid accidental auto-inflation when cleaning the MD3196 LP, do
not submerge it in water or spray liquid on the inflator.
CAUTION: Do not dry clean the LP
1. Hand wash or sponge down the LP in warm, soapy water.
2. Rinse the LP and inflator with clean water, using a clean cloth.
3. Hang the LP to dry on a plastic coat hanger.
4. Always store the LP in a warm, dry place out of direct sunlight.
ACCESSORIES
MA7214-10
Re-Arm Kit: 33 gram CO replacement cylinder and inflator
2
cap for the MD3196
MA7170
Re-Arm Kit: 33 gram CO replacement cylinder for the
2
MD3091
MA3090
MA7219
Harness Assembly
Auto/Manual Conversion Cap for MD3196
GLOSSARY
Term
Definition
CO
Carbon dioxide
2
Improved Outer Tactical Vest
Life preserver
IOTV
LP
MOLLE
PALS
Modular Lightweight Load-carrying Equipment
Pouch Attachment Ladder System
16
Compact Tactical LP Owners Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DO NOT REMOVE
PRIOR TO SALE
For 40 years Mustang Survival has been committed
to providing life support solutions. Through constant
innovation and the application of new technologies,
Mustang is the leading supplier of quality flotation
and hypothermia protection products to the most
demanding users – from fishermen, sailors and power
boaters to the Coast Guard, jet fighter pilots and even
NASA astronauts.
TOLL FREE: 1.800.526.0532
EMAIL:
Mustang Survival and seahorse design is a registered trademark of
Mustang Survival Corp.
Our commitment to quality has earned our Burnaby facilities ISO
9001 registration, the highest of all international standards. This is our
guarantee you are receiving the ultimate in design and manufacturing.
HT1144 (Rev. 15Feb2012)
Download from Www.Somanuals.com. All Manuals Search And Download.
|