PARTS AND OPERATION MANUAL
MQ POWER
DCA-400SSK
DCA-400SSK2
TM
WHISPERWATT
GENERATOR
(STANDARD)
PARTS LIST NO. C3875300104B
S/N UP TO 3701676-400SSK
S/N3101677~ 400SSK2
Revision #3 (09/17/01)
MULTIQUIPINC.
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
800-421-1244
SERVICE DEPARTMENT:
800-835-2551
FAX:310-537-3927
FAX:310-638-8046
E-mail:mq@multiquip.com • www:multiquip.com
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
SERVICE DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Here's How To Get Help .............................................3
Table Of Contents ......................................................4
Rules For Safe Operation ...................................... 6-9
Towing ......................................................................10
Trailer Safety Guidelines .................................... 11-17
Trailer Wiring Diagram..............................................18
Electric Brake Troubleshooting.................................19
Hydraulic Brake Troubleshooting .............................20
Operation And Safety Decals............................. 21-22
Specifications ...........................................................23
General Information ........................................... 24-25
Major Components ..................................................26
Dimensions (Top, Side And Rear)...................... 28-29
Control Panel...................................................... 30-31
Engine Operating Panel ..................................... 32-33
Output Terminal Panel Overview ........................ 34-39
Installation .......................................................... 40-41
Pre-Setup ........................................................... 42-45
Load Application ......................................................46
Generator Start-Up Procedure (Key Switch) ..... 47-50
Generator Start-Up Procedure (Controller) .............51
Generator Shut-Down Procedure ............................52
Maintenance ...................................................... 54-57
Generator Wiring Diagram .......................................58
Engine Wiring Diagram ............................................60
Troubleshooting (Engine)................................... 62-63
Troubleshooting (Generator) ...................................64
Troubleshooting (Engine Controller) ........................65
Explanation Of Codes In Remarks Column .............66
Suggested Spare Parts ............................................67
MQ Power DCA-400SSK
ACGenerator
Generator Assembly .......................................... 68-71
Control Box Assembly ........................................ 72-75
Engine Radiator Assembly................................. 76-79
Engine Operating Panel Assembly .................... 80-81
Output Terminal Assembly ................................. 82-83
Battery Assembly ............................................... 84-85
Actuator Assembly ............................................. 86-87
Muffler Assembly ............................................... 88-89
Fuel Tank Assembly ........................................... 90-91
Enclosure #1 Assembly...................................... 92-95
Enclosure #2 Assembly...................................... 96-99
Enclosure #3 Assembly........................................ 100-
103
Enclosure (Rubber Seals).............................. 104-105
Oil Piping Assembly ....................................... 106-107
Name Plate and Decals ................................. 108-111
Terms and Conditions Of Sale — Parts ................ 112
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
I Dealer account number
I Dealer name and address
I Shipping address (if different than billing address)
I Return fax number
I Applicable model number
I Quantity, part number and description of each part
I Specify preferred method of shipment:
UPS Ground
•
UPS Second Day or Third Day*
•
UPS Next Day*
•
Federal Express Priority One (please provide us with your Federal
Express account number)*
•
Airborne Express*
•
Truck or parcel post
•
*Normally shipped the same day the order is received, if prior to 2PM west coast time.
Earn Extra Discounts when
you order by FAX!
All parts orders which include complete part numbers
and are received by fax qualify for the following extra
discounts:
Number of
line items ordered
Additional Discount
1-9 items
3%
10+ items**
5%
only
s
der
ed or
x
a
f
For
Get special freight allowances
when you order 10 or more
line items via FAX!**
Now! Direct TOLL-FREE access
to our Parts Department!
I
UPS Ground Service at no charge for freight
I
PS Third Day Service at one-half of actual freight cost
Toll-free nationwide:
800-421-1244
No other allowances on freight shipped by any other carrier.
**Common nuts, bolts and washers (all items under $1.00 list price)
do not count towards the 10+ line items.
Toll-free FAX:
*DISCOUNTS ARE SUBJECT TO CHANGE*
800/6-PARTS-7 • 800-672-7877
Fax order discount and UPS special programs revised June 1, 1995
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
I
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or generator.
CAUTION:
Failure to follow instructions in this manual
may lead to serious injury or even death!
This equipment is to be operated by trained
and qualified personnel only!This equipment
is for industrial use only.
I
I
High Temperatures – Allow the
The following safety guidelines should always be used when
operating the DCA-400SSK portable generator:
engine to cool before adding fuel or performing service
and maintenance functions. Contact with hot components
can cause serious burns.
GENERAL SAFETY
I
I
I
DONOToperateorservicethisequipmentbefore
reading this entire manual.
The engine of this generator requires an adequate free
flow of cooling air. Never operate the generator in any
enclosed or narrow area where free flow of the air is
restricted. If the air flow is restricted it will cause serious
damage to the generator or engine and may cause injury
to people.The generator engine gives off DEADLY carbon
monoxide gas.
This equipment should not be operated by
persons under 18 years of age.
NEVER operate this equipment without
proper protective clothing, shatterproof
glasses, steel-toed boots and other
protective devices required by the job.
CAUTION
:
I
I
I
NEVERoperatethisequipmentwhennotfeeling
well due to fatigue, illness or taking medicine.
Always refuel in a well-ventilated area,
away from sparks and open flames.
NEVER operate this equipment under the
influence or drugs or alcohol.
I
Always use extreme caution when
working with flammable liquids.When
refueling, stop the engine and allow it
to cool.DO NOT smoke around or near
the machine. Fire or explosion could
result from fuel vapors, or if fuel is
spilled on a hot engine.
NEVER use accessories or attachments, which are not
recommended by MQ Power for this equipment. Damage
to the equipment and/or injury to user may result.
I
I
I
Manufacturer does not assume responsibility for any
accident due to equipment modifications.
I
NEVER operate the generator in an
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
explosive atmosphere or near combustible materials. An
explosion or fire could result causing severe bodily harm
or even death.
Always check the machine for loosened threads or bolts
before starting.
I
Topping-off to filler port is dangerous, as it tends to spill
fuel.
PAGE 6 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
CAUTION
:
CAUTION
:
DO NOT touch or open any of the below
mentioned components while the
generator is running. Always allow
sufficient time for the engine and generator
to cool before performing maintenance.
I
NEVER touch output terminals during operation. This is
extremely dangerous. Always stop the machine when
contact with the output terminals.
Radiator
1. Radiator Cap - Removing the radiator cap while the
engine is hot, will result in high pressurized, boiling
water to spew out of the radiator, causing severe
scalding to any persons in the general area of the
generator.
CAUTION
:
2. Coolant Drain Plug - Removing the coolant drain
plug while the engine is hot will result in hot coolant
to flow out of the coolant drain plug, therefore causing
severe scalding to any persons in the general area
of the generator.
3. Engine Oil Drain Plug - Removing the engine oil
drain plug while the engine is hot will result in hot oil
to flow out of the oil drain plug, therefore causing
severe scalding to any persons in the general area
of the generator.
I
Backfeed to a utility system can cause electrocution and/
or property damage. Do not connect to any building's
electrical system except through an approved device or
after building main switch is opened.
CAUTION
:
Never use damaged or worn cables when
connecting power tools or equipment to the
generator. Make sure power connecting
cables are securely connected to the
generator’s output terminals, insufficient
tightening of the terminal connections may
cause damage to the generator and
electrical shock.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
Battery
CAUTION
I
I
I
I
NEVER Run engine without air filter. Severe engine
damage may occur.
:
Always service air cleaner frequently to prevent
carburetor malfunction.
Never over fill the battery with water above
the upper limit.
Always disconnect the battery before performing service
on the generator.
Always be sure the operator is familiar with proper safety
precautions and operations techniques before using
generator.
The battery contains acids that can cause injury to the
eyes and skin. To avoid eye irritation, always wear safety
glasses. Use well insulated gloves when picking up the
battery. Use the following guidelines when handling the
battery:
I
Always store equipment properly when not in use.
Equipment should be stored in a clean, dry location out
of the reach of children.
I
I
I
DO NOT leave the generator running in the manual mode
unattended.
DO NOT allow unauthorized people to operate this
equipment.
Always read, understand, and follow procedures in
Operator’s Manual before attempting to operate
equipment.
1. DO NOT drop the battery. There is the possibility of risk
that the battery may explode.
I
Refer to the Komatsu Engine Owner's Manual for
engine technical questions or information.
2. DO NOT expose the battery to open flames, sparks,
cigarettes etc. The battery contains combustible gases
and liquids. If these gases and liquids come in contact
with a flame or spark, an explosion could occur.
Loading and Unloading (Crane)
I
Before lifting, make sure the generator's lifting hook is
secure and that there is no apparent damage to the
generator itself (loose screws, nuts and bolts). If any
part is loose or damaged, please take corrective action
before lifting.
3. Always keep the battery charged. If the battery is not
charged a buildup of combustible gas will occur.
4. Always keep battery charging and booster cables in good
working condition. Repair or replace all worn cables.
I
I
Always drain fuel prior to lifting.
5. Always recharge the battery in an open air environment,
to avoid risk of a dangerous concentration of combustible
gases.
Make sure the crane or lifting device has been properly
secured to the hook of guard frame on generator.
6. In case the battery liquid (dilute sulfuric acid) comes in
contact with clothing or skin, rinse skin or clothing
immediately with plenty of water.
I
I
NEVER lift the machine while the engine is running.
Use adequate lifting cable (wire or straps) of sufficient
strength.
7. In case the battery liquid (dilute sulfuric acid) comes in
contact with your eyes, rinse eyes immediately with
plenty of water, then contact the nearest doctor or hospital,
and seek medical attention.
I
I
I
When lifting the generator, always use the balanced
center-point suspension hook and lift straight upwards.
NEVER allow any person or animal to stand underneath
the machine while lifting.
When loading the generator on a truck, be sure to use
the front and back frame bars as a means to secure
the generator during transport.
PAGE 8 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
Transporting
I
I
I
Always shutdown engine before transporting.
Tighten fuel tank cap securely.
Drain fuel when transporting generator over long distances
or deteriorated roads.
I
I
Always tie-down the generator during transportation by
securing the generator.
If generator is mounted on a trailer, make sure trailer
complies with all local and state safety transportation
laws. See page 10 for basic towing procedures.
Emergencies
I
Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department.
Maintenance Safety
I
NEVER lubricate components or attempt service on a
running machine.
I
Always allow the machine a proper amount of time to
cool before servicing.
I
I
Keep the 0in proper running condition.
Fix damage to the machine immediately and always
replace broken parts.
I
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, coolant,
fuel, and fuel filters.
I
I
DO NOT use plastic containers to dispose of hazardous
waste.
DO NOT pour waste, oil, coolant or fuel directly onto the
ground, down a drain or into any water source
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TOWING
Towing Safety Precautions
I
I
ALWAYS attach trailer's safety chain to bumper of towing
vehicle.
CAUTION :
ALWAYS make sure the vehicle and trailer directional,
backup, brake, and trailer lights are connected and
working properly.
Check with your county or state safety
towing regulations department before
towing your generator.
I
The maximum speed unless otherwise posted for highway
towing is 55 MPH. It is not recommended for off-road
towing. However, if necessary, do not exceed 15 MPH
or less depending on type of terrain to prevent damage
to the axles.
To reduce the possibility of an accident while transporting
the generator on public roads, always make sure the trailer
(Figure 1) that supports the generator and the towing vehicle
are in good operating condition and both units are
mechanically sound.
I
I
I
Place chocked blocks underneath wheel to prevent
rolling, while parked.
Place support blocks underneath the trailer's bumper to
prevent tipping, while parked.
The following list of suggestions should be used when towing
your generator:
Use the trailer's hand winch to adjust the height of the
trailer, then insert locking pin to lock wheel stand in place,
while parked.
I
Make sure the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer "gross vehicle
weight rating" (GVWR).
I
Avoid sudden stops and starts.This can cause skidding,
or jackknifing. Smooth, gradual starts and stops will
improve gas milage.
I
ALWAYS inspect the hitch and coupling for wear.NEVER
tow a trailer with defective hitches, couplings, chains
etc.
I
I
I
Avoid sharp turns to prevent rolling.
I
I
Check the tire air pressure on both towing vehicle and
trailer. Also check the tire tread wear on both vehicles.
Remove wheel stand when transporting.
DO NOT transport generator with fuel in tank.
ALWAYS make sure the trailer is equipped with a "Safety
Chain".
Figure 1. Generator with Trailer
PAGE 10 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — TRAILER-SAFETY GUIDELINES
4. Frame Length - This measurement is from the ball
CAUTION:
hitch to the rear bumper (reflector).
ALWAYS make sure the trailer is in good
5. Frame Width - This measurement is from fender to
fender.
operating condition. Check the tires for
proper inflation and wear. Also check the
wheel lug nuts for proper tightness.
6. Jack Stand - Trailer support device with maximum
pound requirement from the tongue of the trailer.
7. Coupler - Type of hitch used on the trailer for towing.
Usually consists of chains and ‘ball’ or ‘eye’.
8. Tire Size - Indicates the diameter of the tire in inches
(10,12,14, etc.), and the width in millimeters
(175,185,205, etc.). The tire diameter must match the
diameter of the tire rim.
9. Tire Ply - The tire ply (layers) number is rated in
letters; 2-ply,4-ply,6-ply, etc.
10. Wheel Hub - The wheel hub is connected to the
trailer’s axle.
11. Tire Rim - Tires mounted on a tire rim. The tire rim must
match the size of the tire.
12. Lug Nuts - Used to secure the wheel to the wheel hub.
Always use a torque wrench to tighten down the lug
nuts. SeeTable 4 and Figure 5 or lug nut tightening and
sequence.
13. Axle - Indicates the maximum weight the axle can sup-
port in pounds, and the diameter of the axle expressed
in inches (see Table 3). Please not that some trailers
have a double axle. This will be shown as 2-6000 lbs.,
meaning two axles with a total weight capacity of 6000
pounds.
14. Suspension - Protects the trailer chassis from shocks
transmitted through the wheels. Types of suspension
used are leaf, Q-flex, and air ride.
Explanation of Chart:
This section is intended to provide the user with trailer ser-
vice and maintenance information. The service and mainte-
nance guidelines referenced in this section apply a wide range
of trailers. Remember periodic inspection of the trailer will
ensure safe towing of the equipment and will prevent dam-
age to the equipment and personal injury.
It is the purpose of this section to cover the major mainte-
nance components of the trailer. The following trailer com-
ponents will be discussed in this section:
„
„
„
„
„
„
Brakes
Tires
Lug NutTorquing
Suspension
Electrical
Brake Troubleshooting Tables
Use the following definitions with reading Table 1.
1. Fuel Cell - Provides an adequate amount of fuel for
the equipment in use. Fuel cells must be empty when
transporting equipment.
2. Braking System - System employed in stopping the
trailer. Typical braking systems are electric, surge, hy-
draulic, hydraulic-surge and air.
3. GVWR- Gross Vehicle Weight Rating (GVWR), is the
maximum number of pounds the trailer can carry, in-
cluding the fuel cell (empty).
15. Electrical - Electrical connectors (looms) are provided
with the trailer so the brake lights and turn signals can
be connected to the towing vehicle.
16. Application - Indicates which units can be employed
on a particular trailer.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TRAILER-SPECIFICATIONS
Table 1. Specifications
MODEL
APPLICATION
FUEL CELL
BRAKE SYSTEM
GVWR
FRAME
LENGTH
FRAME
WIDTH
JACK
STAND
SDW225,
SGW250,TLW300
NO
NO
NO
1900LBS
1900LBS
1900LBS
2200LBS
2700LBS
2700LBS
2700LBS
7000LBS
7000LBS
7000LBS
7000LBS
10000LBS
11160LBS
14000LBS
18000LBS
18000LBS
30000LBS
30000LBS
96"
96"
96"
85"
50"
50"
50"
42"
800LB.
FULL TILT WHEEL
TRLR-10W
TRLR-10
DCA10, TLG12, DCA-
15
NO
800LB.
FULL TILT WHEEL
DCA10, TLG-12,
DCA15, TLW-300
52 GAL
NO
NO
NO
800LB.
FULL TILT WHEEL
TRLR-10XF
TRLR-225W
TRLR-BLW400
TRLR-50X
WELDERS,
DA7000SS
800LB.
FULL TILT WHEEL
BLW-400
NO
ELECTRIC
NO
W/MAST 154"
W/O 124"
55"
(78" TALL)
800LB.
FULL TILT WHEEL
DCA-25
NO
124"
124"
186"
138"
138"
190"
186"
204"
222"
238"
238"
384"
384"
55"
55"
77"
66"
66"
76"
77"
84"
83"
83"
83"
96"
96"
800LB.
FULL TILT WHEEL
DCA-25
41 GAL
NO
NO
800LB.
FULL TILT WHEEL
TRLR-50XF
TRLR-70W
DCA-45, -60, 70
DCA-45, -60, 70
DCA-45, -60, 70
DCA-100, 125
DCA-85, 100, 125
DCA-150, 180
DCA-220
SURGE
2000LB.
FLAT PAD
OPT
SURGE
2000LB.
FLAT PAD
TRLR-70X
53 GAL
150 GAL
145 GAL
200 GAL
250 GAL
250 GAL
350 GAL
550 GAL
550 GAL
SURGE
2000LB.
FLAT PAD
TRLR-70XF
TRLR-100XF
TRLR-85/125
TRLR-150XF
TRLR-220XF
TRLR-300XF
TRLR-400XF
TRLR-600XF
TRLR-800SX
HYDRAULIC SURGE
HYDRAULIC
HYDRAULIC SURGE
HYDRAULIC SURGE
HYDRAULIC SURGE
ELECTRIC
AIR
2000LB.
FLAT PAD
2000LB.
FLAT PAD
5000 LB.
FLAT PAD
5000 LB.
FLAT PAD
DCA-300
5000 LB.
FLAT PAD
DCA-400
5000 LB.
FLAT PAD
DCA-600, 800
DCA-600, 800
5000 LB.
FLAT PAD
AIR
5000 LB.
FLAT PAD
PAGE 12 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TRAILER-SPECIFICATIONS
Table 1. Specifications (Con't)
MODEL
COUPLER
TIRES
WHEELS
AXLE
HUBS
SUSPENSION
ELECTRICAL
2" BALL CLASS
2 ADJUSTABLE
175-13C
13"X4.50"
2200# 2X2
5 LUG
3 LEAF
4 WIRE LOOM W/
4 POLE FLAT
TRLR-10W
2"BALL CLASS
2 ADJUSTABLE
175-13C
175-13C
13"X4.5"
13"X4.5"
13X4.5"
13 X 4.5"
13"X4.50"
13"X4.50"
14"X5"
2200#2X2
2200#2X2
2200#2X2
2200#2X2
5 LUG
5 LUG
5 LUG
5 LUG
5 LUG
5 LUG
5 LUG
5 LUG
5 LUG
5 LUG
6 LUG
8 LUG
8 LUG
8 LUG
8 LUG
8 LUG
8 LUG
3 LEAF
3 LEAF
Q FLEX
3 LEAF
4 LEAF
4 LEAF
5 LEAF
5 LEAF
5 LEAF
5 LEAF
7 LEAF
7 LEAF
Q FLEX
Q FLEX
Q FLEX
7 LEAF
AIR-RIDE
4 POLE FLAT
TRLR-10
2"BALL CLASS
2 ADJUSTABLE
4 POLE FLAT
TRLR-10XF
2"BALL CLASS
2 ADJUSTABLE
175-13B
4 POLE FLAT
TRLR-225W
2"BALL CLASS
2 ADJUSTABLE
175-13C
4 POLE FLAT
TRLR-BLW 400
2" BALL CLASS
B78-13LRC
B78-13LRC
3500lbs.
2-3/8"
4 POLE RUBBER FLAT
4 POLE RUBBER FLAT
4 POLE RUBBER FLAT
4 POLE RUBBER FLAT
4 POLE RUBBER FLAT
4 WIRE LOOM
TRLR-50X
TRLR-50XF
TRLR-70W
2" BALL CLASS
3500lbs.
2-3/8"
2" BALL CLASS
3" ADJUSTABLE
205-14C
BIAS (4)
3500lbs.
3"
2" BALL CLASS
3" ADJUSTABLE
205-14C
BIAS (4)
14"X5"
3500lbs
3"
TRLR-70X
2" BALL CLASS
3" ADJUSTABLE
205-14C
BIAS (4)
14"X5"
3500lbs.
3"
TRLR-70XF
TRLR-100XF
TRLR-85/125
TRLR-150XF
TRLR-220XF
TRLR-300XF
TRLR-400XF
TRLR-600XF
TRLR-800AR
ADJUSTABLE 2-5/6 OPT
3" EYE
205-15C
BIAS (4)
14"X5.5"
14"x6"
3500lbs
3"
ADJUSTABLE 2-5/6 OPT
3" EYE
ST225/75R15D
RADIAL (4)
(2)-6000lbs
(2)-6000lbs
(2)-7000lbs
(2)-6000lbs
(3)-7000lbs.
(3)-10000lbs
(3)-10000lbs
4 WIRE LOOM
3" BALL EYE
3" EYE ADJUSTABLE
3" EYE ADJUSTABLE
3" EYE ADJUSTABLE
5TH WHEEL
750-16 E
BIAS (4)
16"X7"
4 WIRE LOOM
ST235/85R16E
RADIAL(4)
16"X7"
4 WIRE LOOM
ST235/85R16E
RADIAL(6)
16"X7"
4 WIRE LOOM
ST235/85R16E
RADIAL(6)
16"X7"
4 WIRE LOOM
ST215/75R17.5H
RADIAL (8)
16"X7"
6 WIRE LOOM
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16"X7"
6 WIRE LOOM
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TRAILER SAFETY GUIDELINES
Brakes
Before any brake synchronizations adjustments can be made,
If your trailer has a braking system, the brakes should be the trailer brakes should be burnished-in by applying the
inspected the first 200 miles of operation. This will allow the brakes 20-30 times with approximately a 20 m.p.h. decrease
brake shoes and drums to seat properly. After the first 200 in speed, e.g. 40 m.p.h. to 20 m.p.h. Allow ample time for
mile interval, inspect the brakes every 3,000 miles. If driving brakes to cool between application. This allows the brake
over rough terrain, inspect the brakes more frequently.
shoes to slightly be seated into the brake drum surface.
Electric Brakes
Figure 2 displays the major electric brake components that
Electrically actuated brakes (Figure 2) are similar to hydraulic will require inspection and maintenance. Please inspect these
brakes. The basic difference is that hydraulic brakes are components as required.
actuated by an electromagnet.
Electric Brake Adjustment
Listed below are some of the advantages that electric brakes
have over hydraulic brakes:
1. Place the trailer on jack stands. Make sure the jack
stands are placed on secure level ground.
„
„
„
„
Brake system can be manually adjusted to provide the
corrected braking capability for varying road and load
conditions
2. Check the wheel and drum for free rotation.
3. Remove the adjusting hole cover from the adjusting slot
at the bottom brake backing plate.
Brake system can be modulated to provide more or less
braking force, thus easing the brake load on the towing
vehicle
4. With a screwdriver or standard adjusting tool, rotate the
star wheel of the adjuster assembly to expand the brake
shoes.
Brake system has very little lag time between the time
the vehicle’s brakes are actuated and the trailer’s brakes
are actuated
5. Adjust the brake shoes outward until the pressure of the
lining against the wheel drum makes the wheel difficult
to turn.
Brake system can provide an independent emergency
brake system
6. Rotate the star wheel in the opposite direction until the
wheel rotates freely with slight lining drag.
7. Replace the adjusting hole cover and lower the trailer to
the ground.
Remember in order to properly synchronize the tow vehicle’s
braking to the trailer’s braking, can only be accomplished by
road testing. Brake lockup, grabbiness or harshness is due
to lack of synchronization between the tow vehicle and the
trailer being towed or under-adjusted brakes.
8. Repeat steps 1 through 6 on the remaining brakes.
PAGE 14 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TRAILER SAFETY GUIDELINES
Figure 2. Electrical Brake Components
Hydraulic/Air/Surge Brakes
components that will require inspection and maintenance.
Hydraulic brakes (Figure 3) should not require any special Please inspect these components as required using steps 1
attention with the exception of routine maintenance such as through 6 as referenced in the electric brake adjustments
shoe and lining replacement. These brakes can be adjusted section.
in the same manner as electric brakes. Brake lines should
be periodically checked for cracks, kinks, or blockage.
Figure 3 below displays the major hydraulic/air/surge brake
Figure 3. Hydraulic Brake Components
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TRAILER SAFETY GUIDELINES
Tires/Wheels/Lug Nuts
Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing the
trailer wheels it is important the wheels, tires, and axle are
properly matched.
CAUTION:
DO NOT attempt to repair or modify a
wheel. DO NOT install in inner tube to
correct a leak through the rim. If the rim
is cracked, the air pressure in the inner
tube may cause pieces of the rim to
explode (break off) with great force and
cause serious eye or bodily injury.
Suspension
The leaf suspension springs and associated components
(Figure 4) should be visually inspected every 6,000 miles for
signs of excessive wear, elongation of bolt holes, and
loosening of fasteners. Replace all damaged parts
(suspension) immediately. Torqued suspension components
as detailed in Table 3.
Tire Wear/Inflation
Tire inflation pressure is the most important factor in tire life.
Pressure should be checked cold before operation DO NOT
bleed air from tires when they are hot. Check inflation
pressure weekly during use to insure the maximum tire life
and tread wear.
Table 2 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
CAUTION:
NOTE
ALWAYS wear safety glasses when removing
or installing force fitted parts. Failure to comply
may result in serious injury.
Figure 4. Major Suspension Components
PAGE 16 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TRAILER SAFETY GUIDELINES
Table 3. Suspension Torque Requirements
Item
Torque (Ft.-Lbs.)
MIN-30 MAX-35
MIN-45 MAX-60
MIN-45 MAX-60
3/8" U-BOLT
7/16" U-BOLT
1/2" U-BOLT
SNUG FIT ONLY. PARTS MUST ROTATE FREELY. LOCKING
NUTS OR COTTER PINS ARE PROVIDED TO RETAIN NUT-BOLT
ASSEMBLY.
SHACKLE BOLT
SPRING EYE BOLT
SHOULDER TYPE
SHACKLE BOLT
MIN-30 MAX-50
Lug NutTorque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque on the trailer. Be sure to use only the
fasteners matched to the cone angle of the wheel. Proper
procedure for attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence. See Figure 5. DO NOT
torque the wheel lug nuts all the way down. Tighten
each lug nut in 3 separate passes as defined byTable 4.
3.
After first road use, retorque all lug nuts in sequence.
Check all wheel lug nuts periodically.
Table 4. Tire Torque Requirements
Wheel Size
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
12"
13"
14"
15"
16"
20-25
20-25
20-25
20-25
20-25
35-40
35-40
50-60
50-60
50-60
50-65
50-65
90-120
90-120
90-120
Figure 5. Wheel Lug Nuts Tightening Sequence
NOTE
NEVER use an pneumatic air gun to
tighten wheel lug nuts.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TRAILER-WIRING DIAGRAM
NOTE:
LIGHTS ARE ORIENTED FROM THE DRIVER’S SEAT
PAGE 18 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TRAILER-BRAKETROUBLESHOOTING
Table 5. Electric Brake Troubleshooting
Symptom
Possible Cause
Any open circuits or broken wires?
Any short circuits?
Solution
No Brakes or Intermittent
Brakes
Find and correct.
Find and correct.
Test and correct.
Find and repair.
Find and secure.
Clean or replace.
Faulty controller?
Any loose connections?
Ground wire secure?
Weak Brakes or Brakes
Pull to One Side
Grease or oil on magnets or linings?
Connections corroded?
Clean and correct
cause of corrosion.
Brake drums scored or grooved?
Brakes synchronized?
Machine or replace.
Correct.
Locking Brakes
Brake components loose, bent or
broken?
Replace components.
Brake drums out-of-round?
System lubricated?
Replace.
Lubricate.
Noisy Brakes
Brake components correct?
Bearings of the wheel adjusted?
Replace and correct.
Adjust.
Dragging Brakes
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TRAILER-BRAKETROUBLESHOOTING
Table 6. Hydraulic Brake Troubleshooting
Symptom
Possible Cause
Brake line broken or kinked?
Brake lining glazed?
Solution
Repair or replace.
Reburnish or replace.
Correct weight.
No Brakes
Weak Brakes or Brakes Pull to
One Side
Trailer overloaded?
Brake drums scored or grooved?
Tire pressure correct?
Machine or replace.
Inflate all tires equally.
Match tires.
Tires unmatched on the same axle?
Brake components loose, bent or broken?
Brake drums out-of-round?
System lubricated?
Locking Brakes
Noisy Brakes
Replace components.
Replace.
Lubricate.
Brake components correct?
Replace and correct.
Dragging Brakes
Brake lining thickness correct or in right
wrong position?
Install new shoes and
linings.
Enough brake fluid or correct fluid?
Replace rubber parts
fill with dot4 fluid.
PAGE 20 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OPERATION AND SAFETY DECALS
Machine Safety Decals
The DCA-400SSK generator is equipped with a number of safety decals.These decals are provided for operator safety and
maintenance information. The illustration below and on the preceding pages shows the decals as they appear on the
machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OPERATION AND SAFETY DECALS
PAGE 22 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — SPECIFICATIONS
Table 7. Specifications
Generator Specifications
Model
Type
DCA-400SSK
Revolving field, self ventilated, open protected type synchronous generator
Armature Connection
Phase
Star with Neutral
3
Standby Output
Prime Output
Voltage
440 KVA (352.0 KW)
400 KVA (320.0 KW)
240V or 480V
Frequency
Speed
60 Hz
1800 rpm
Power Factor
Aux. AC Power
Voltage
0.8
Single Phase, 60 Hz
120 V
Output
4.8 KW (2.4 KW x 2)
Engine Specifications
KOMATSU SA6D140E-2
4 Cycle, water-cooled, direct injection, turbo-charged with after-cooler
6 cylinders
Model
Type
No. of Cylinders
Bore x Stroke
Rated Output
Displacement
Starting
5.5 in. x 6.5 in. (140 mm x 165mm)
478 HP/1800 rpm
930 cu. in. (15240 cc)
Electric
Coolant Capacity
Lube Oil Capacity
16.9 gal. (58 liters)
19.5 gal. (74 liters)
20.4gal. (77.5L)/hr at full load
15.8gal.(59.8L)/hr at 3/4 load
Fuel Consumption
11.0gal.(41.6L)/hr at 1/2 load
6.6gal.(25.0L)/hr at 1/4 load
Battery
Fuel
12V- 200 AH x 2
#2 Diesel Fuel
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — GENERAL INFORMATION
DCA-400SSK FAMILIARIZATION
Generator
Control Box
The “Control Box” is provided with the following:
z
z
z
z
z
Main Circuit Breaker 1060 amps
Over-Current Relay
High Idle Adjust Trimmer
CurrentTransformer
The MQ Power Model DCA-400SSK is a 320 kW generator
that is designed as a high quality portable (requires a trailer
for transport) power source for telecom sites, lighting
facilities, power tools, submersible pumps and other
industrial and construction machinery.
Automatic Voltage Regulator
Engine Control Panel
Open Delta Excitation System
The “Engine Control Panel” is provided with the following:
z
z
z
z
z
z
z
z
z
z
z
z
Auto/Start/Stop Controller (S/N 3696510~)
Tachometer
WaterTemperature Gauge
Oil Pressure Gauge
Charging Ammeter Gauge
EngineWarning Lamp Module
Engine Speed Switch (S/N3701667~)
Pre-Heat Button
The DCA-400SSK generator is equipped with the state of
the art "Open-Delta" excitation system. The open delta
system consist of an electrically independent winding wound
among stationary windings of the AC output section.
There are four leads: A, B, C and D. During light loads, the
power to the Automatic Voltage Regulator (AVR) is supplied
from the leads parallel connections of B&C. When loads
increase, the AVR switches and accepts power from leads
A&D. The output of leads A&D increase proportionally with
load. This of adding the voltages to each phase provides
better voltage response during heavy loads.
Pre-Heat Lamp
Emergency Stop Button
Battery Switch
Starter Switch (Up to S/N3696509)
The connections of the AVR to the AC output windings are
for sensing only. No power is required from these windings.
Generator Control Panel
The open-delta design provides virtually unlimited excitation
current, offering maximum motor starting capabilities. The
excitation does not have a "fixed ceiling" and responds
according the demands of the required load.
The “Generator Control Panel”is provided with the following:
z
z
z
z
z
z
z
z
z
z
Output Voltage Adjustment Knob
Frequency Meter (Hz)
AC Ammeter (Amps)
AC Voltmeter (Volts)
Ammeter Change-Over Switch
Voltmeter Change-Over Switch
Panel Light
Auto On/Off Engine Controller
Panel Light Switch
Pilot Lamp
Engine Controller Alarm System
The DCA-400SSK generator is equipped with various alarms
and LED status indicators.These alarms and status indicators
are provided to add safety to the generator when operating
under normal conditions. The DCA-400SSK generator is
designed to shutdown in the event of low oil, high coolant
temperature, low battery and other operation conditions that
may cause severe damage to the generator.
Output Terminal Panel
The “Output Terminal Panel” is provided with the following:
z
z
z
z
Three120/240V output receptacles, 50 amp
Two 120V receptacles, 20 amp
3 Circuit Breakers 240V @50 amps
2 GFCI Circuit Breakers 125V@ 20amps
PAGE 24 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — GENERAL INFORMATION
Engine
The DCA-400SSK is powered by a 4 cycle, water cooled,
turbocharged KOMATSU Model SA6D140E-2 diesel engine.
This engine is designed to meet every performance
requirement for the generator. Reference Table 1, page 16
for engine specifications.
Electronic Governor System
The electronic governor system replaces the standard
mechanical governor system. The frequency regulation
improves from 3.0% regulation with the mechanical governor
to 0.25% regulation with the electronic governor system.
JacketWater Heater (OPTIONAL)
The jacket water heater is a 1500-watt heater designed to
keep the coolant warm in the engine block for fast starts
and load acceptance. The heater is thermostatically
controlled and once an acceptable engine temperature is
achieved it will cycle on and off, operating only about 1/3 of
the time, which makes it more efficient than the direct block
type heater. It is designed to keep the engine coolant
between 100 and 120 degrees Fahrenheit.
Under normal conditions, 20 to 15 minutes is required to
raise the engine temperature of a cold engine to 100 degrees
Fahrenheit.
Battery Charger
The battery charger will operate in a‘BOOST’mode until the
battery’s current acceptance falls to 70% of the charger’s
rating. The charger will then go into a ‘FLOAT’mode, where
it discharges a lower voltage until an AC failure, or the battery
is discharged.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — MAJOR COMPONENTS
Figure 6. Major Components
PAGE 26 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — DIMENSIONS (TOP AND SIDE)
Dry weight: 4270kg (9413.64lb)
Wet weight: 4800kg (10582.08 lb)
Figure 7a. Dimensions
PAGE 28 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — DIMENSIONS (FRONT AND REAR)
Figure 7b. Dimensions
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — CONTROL PANEL
Figure 8. Control Panel
PAGE 30 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — CONTROL PANEL
The definitions below describe the controls and functions of
the DCA-400SSK " Control Panel " (Figure 8).
If the engine does not engage (start) by the third attempt,
the engine will be shutdown by the engine controller's " Over
Crank Protection" mode. If the engine engages at a speed
(RPM's) that is not safe, the engine controller will shutdown
the engine by initializing the "Over Speed Protection" mode.
1. Pilot Lamp – Indicates that the generator is working
properly.
2. Panel Light – Normally used in dark areas or at night
time.When activated, panel lights will illuminate.When
the generator is not in use be sure to turn the panel
light switch to the OFF position.
Also the engine controller will shutdown the generator in the
event of low oil pressure, high coolant temperature, low
coolant level, and loss of magnetic pickup.These conditions
can be observed by monitoring the LED status indicators on
the front of the engine controller module.
3. Frequency Meter – Indicates the output frequency in
hertz (Hz). Normally 60 Hz 1 Hz .
A. Off/Manual/Auto Switch – This switch controls the
running of the generator.If this switch is left in the "OFF"
position, the generator will not run. When this switch is
set to the manual position, the generator will start
immediately.
4. AC Ammeter – Indicates the amount of current the
load is drawing from the generator.
5. AC Voltmeter – Indicates the single phase output
voltage present at the UVW terminals.
If the generator is to be connected to a building's AC
power source via a transfer switch (isolation), place
the switch in the auto position. In this position the
generator will monitor the AC line output from the
building's power source.
6. Ammeter Change-Over Switch – This switch allows
the AC ammeter to indicate the current flowing to the
load connected to any phase of the output terminals, or
to be switched off.
7. Voltmeter Change-Over Switch – This switch allows
the AC voltmeter to indicate phase to phase voltage
between any two phases of the output terminals or to
be switched off.
B. Low Oil Pressure – Indicates the engine pressure
has fallen below 15 psi. The oil pressure is detected
using variable resistive values from the oil pressure
sending unit. This is considered a major fault.
8. Panel Light Switch – When activated will turn on control
C. High Coolant Temperature – Indicates the engine
temperature has exceeded 215°F. The engine
temperature is detected using variable resistive values
from the temperature sending unit. This is considered
a major fault.
panel light.
9. Voltage Regulator Control – Allows manual
adjustment of the generator’s output voltage.
10. Engine Controller (for S/N 3696510~) – The engine
controller as a vertical row of status LED's (Figure 9),
that when lit, indicate that an engine malfunction (fault),
has been detected. When a fault has been detected
the engine controller will evaluate the fault and if the
fault is major will shutdown
D. Overcrank Shutdown – Indicates the unit has
attempted to start a pre- programmed number of times,
and has failed to start. The number of cycles and
duration are programmable.Typical programmable start
settings is 3 cycles with a 10 second duration .This is
considered a major fault.
the generator.
E. Overspeed Shutdown – Indicates the engine is
running at an unsafe speed.This is considered a major
fault.
During cranking cycle , The
engine controller will attempt to
crank the engine for 10 seconds
before disengaging.
F. Engine Running – Indicates that engine is running at
a safe operating speed.
11. Main Circuit Breaker – This three-pole, 1000 amp main
breaker is provided to protect the UVW voltage output
terminals from overload.
Figure 9. Engine
Controller Module
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENGINE OPERATING PANEL
Figure 10. Engine Operating Panel
PAGE 32 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENGINE OPERATING PANEL
The definitions below describe the controls and functions of 4. Oil Pressure Gauge – During normal operation this
the DCA-400SSK " Engine Operating Panel "(Figure 10).
gauge be should read between 42-71 psi. When starting
the generator the oil pressure mar read a little bit higher,
but after the engine warms up the oil pressure should
return to normal.
1. Throttle Handle ( up to S/N 3701676) - This handle
controls the speed of the engine (low or high).
2. Tachometer – Indicates engine speed in RPM’s for 60
Hz operation. This meter should indicate 1800 RPM’s
when the rated load is applied. In addition a built in hour
5. WaterTemperature Gauge – During normal operation
this gauge be should read between 165-203oF.
meter will record the number of operational hours that 6. Charging Ammeter Gauge – Indicates the current
the generator has been in use.
being supplied by the engine’s alternator which provides
current for generator’s control circuits and battery
charging system.
3. Engine Warning Display Module – This module
display’s the following engine failures:
7. Fuel Gauge - Indicates amount of diesel fuel available.
A. Overheat Lamp – This lamp goes ON when
the cooling water temperature rises
abnormally.If the lamp goes ON during normal
operation of the generator, the emergency
shutdown device will stop the engine
automatically.
8. Pre-Heat Lamp – Indicates that the glow
plugs of the diesel engine are hot and the
engine is ready to be started.
B. Low Oil Pressure Lamp – During normal
operation of the generator this lamp should
remain OFF. When the Auto-OFF/Reset-
Manual switch is set to the “Manual” position
to start the engine, the lamp will be lit.After
the oil pressure rises after start-up the lamp will go
OFF. If this lamp is ever lit (ON) during normal operation
of the generator, the emergency shutdown device will
stop the engine automatically.
9. Pre-Heat Lamp –Press and hold this
button until the preheat lamp is lit (ON).
10. Emergency Stop Button – Push this
button inward to stop the engine in the
event of an emergency.DO NOT use this
button as a means of stopping the
engine.
11. Ignition Switch (up to S/N3696509)
– Use this switch to preheat the
engine and turn on the generator
(This feature will not be on the unit if
it is equipped with a engine controller-
see Control Panel).
C. Low Fuel Level Lamp – When this lamp is
ON, it is time to stop the engine and add
fuel. Remember to let the engine cool before
adding fuel.
D. Low Battery Fluid Lamp – This lamp goes
ON when the battery fluid is low.If this lamp
goes ON during normal operation of the
generator, stop the engine and fill the
battery with distilled water to the specified
level.
12. Battery Switch – This switch should
be set to the ON position during
normal operation. When the engine
has been stop, place this switch in
the OFF position. DO NOT turn this
switch during normal operation, it
could cause damage to the electrical
equipment
E. Clogged Air Filter Lamp – This lamp goes
ON when the air filter is clogged. If this
lamp goes ON during normal operation of
the generator, stop the engine and replace
the air filter.
13. Engine Speed Switch (S/N 3701677~) – This switch
controls the speed of the engine (high/low).
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OUTPUTTERMINAL PANEL OVERVIEW
Connecting Load
OUTPUTTERMINAL FAMILIARIZATION
Loads can be connected to the generator by the UVWO Lugs or
the convenience receptacles. (See figure 13). Make sure to
read the operation manual before attempting to connect a load
to the generator.
The “Output Terminal Panel” is provided with the following:
z
z
z
z
z
Two 120V GFCI receptacles, 20 amp
Three 120/240V output receptacles, 50 amp
Two 120V output receptacles, 20 amp (optional)
3 Circuit Breakers 240V @50 amps
2 GFCI Circuit Breakers 125V@ 20 amps
Control Box
The “Control Box” is provided with the following:
z
z
Main Circuit Breaker 1000 amps
Over-Current Relay
Output Terminal Panel
The Output Control Panel (See Figure 14) is located on the
right hand side (left from control panel) of the generator.
The UVWO lugs are protected by a face plate cover that
can be secured in the close position by a pad lock. (See
Figure 11).
FIGURE 13. Connecting Load
Circuit Breakers
To protect the generator from an overload, a 3-pole, 1000
amp, main circuit breaker is provided to protect the UVW
output terminals from overload. In addition two single-pole,
20 amp GFCI circuit breakers are provided to protect the
GFCI receptacles from overload.Three 50 amp load circuit
breakers have also been provided to protect the load side of
the generator from overload. Make sure to switch ALL circuit
breakers to the "OFF" position prior to starting the engine.
Maximum Output
The entire load connected to the UVWO Lugs, all four slots in
the duplex receptacles, and the must not exceed 352 kW in
standby or 320 in prime output.
FIGURE 11. Output Terminal Cover
120Volt Recetacle
Two GFCI Duplex Nema 5-20R (120V, 20 Amp) recepacle is
provided on the output terminal. This receptacle can be
used anytime the generator is in operation. The receptacle
is controlled by the circuit breaker located on the control
panel.
Twist Lock DualVoltage Receptacles
Three CS-6369 auxiliary power receptacles have been
provided to supply 208/120V. The voltage regulator knob
on the control panel may need to be used to adjust the
voltage to 208 or 416V.
Pressing the reset button resets the receptacle after being
tripped. Pressing the "Test Button" (See Figure 12) in the
center of this receptacle will check the GFCI function. The
receptacle should be tested at least once a month.
Input Receptacles
Two 120 volt, 20 amp input receptacles are provided to supply
power to accessories, such as the battery charger (optional) or
jacket water heater (optional).
FIGURE 12. GFCI Test Button
PAGE 34 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OUTPUTTERMINAL PANEL OVERVIEW
d are
FIGURE 14. Output Terminal Panel
unds.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OUTPUTTERMINAL PANEL OVERVIEW
Maximum Amps
Output Terminal Panel Available Voltages
The following table show the maximum amps the entire
generator can provide. Do not exceed the maximum amps
listed. (See Table 9)
A wide range of voltages are available to supply load to
many different applications. Voltages may be selected by
using the voltage change-over board and how you hookup
your hard wire connection to the generator. To obtain some
of the voltages listed, fine adjustment with the Voltage
Regulator on the control panel is necessary. See the table
below (Table 8) for a list of available voltages the generator
is able to supply.
Table 9. Maximum Amps
Model:
DCA400SSK
Maximum Amps
888.9 amps (4 wire)
444.4 amps (4 wire)
962.3 amps
TABLE 8. VOLTAGES AVAILABLE
MODEL
DCA400SSK
208 VOLT
Rated Voltage
3 PHASE VOLTAGE
(RECONNECTABLE)
220 VOLT
127 VOLT
240 VOLT
139 VOLT
416 VOLT
240 VOLT
440 VOLT
254 VOLT
480 VOLT
277 VOLT
SINGLE PHASE
(ADJUSTABLE)
120 VOLT
Single Phase 120
Volt
Single Phase 240
Volt
CAUTION :
Three Phase
240 Volt
NEVER attempt to change the Voltage
Change-over board while the engine is
engaged.
Three Phase
480 Volt
481.1 amps
Over Current Relay
An over current relay is connected to the circuit breaker.
In an over current situation, both the circuit breaker and
the over current relay may trip. If the circuit breaker can
not be reset, the reset button on the over current relay
must be pressed. The over current relay is located in the
control box.
PAGE 36 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OUTPUTTERMINAL PANEL OVERVIEW
How to read the output terminal gauges.
The gauges and knobs on the control panel DO NOT effect
the generator output in any fashion. They are there to
simply help the operator observe how much power is being
supplied produced at the UVWO legs.
To read the output of the W-U legs, for example, place the
AC Voltmeter Change-over switch to the W-U position and
the AC ammeter Change -over Switch to the U or W
position to read the output on the selected leg.
FIGURE 15. AC Voltmeter
FIGURE 16. AC Voltmeter
Change-over switch
Gauge
(Reading the W-U leg on
(Volt reading on W-U Lug)
the output terminal panel)
FIGURE 18. AC Ammeter
(Amp reading on U lug)
FIGURE 17. AC Ammeter
Change-over Switch
(Reading the U leg on the
output terminal panel)
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OUTPUTTERMINAL PANEL OVERVIEW
Voltage Change-over Board
Single Phase, 240 Volt
The voltage change-over board changes the available
voltages of the output terminal panel UVWO lugs. The
voltage change-over board is located on the control box
behind the control panel. There are six (6) plates that can
be set into two set positions to get six different voltages.
Unless specified differently, the generator comes from the
factory in the 240V position.
The following connection, with the voltage change-over
board set into the 240V set position (See Figure 19), can
offer SINGLE PHASE power at 240V. After hooking up
the hard wires to the lugs as shown in figure 21 below,
240V will be the voltage output.
240 Volt Set position
The voltage change-over board 240V set position uses all
6 plates in 6 different connection places. See figure 19
below.
FIGURE 21. Hard Wire Hookup for Single Phase 240V
FIGURE 19. Voltage Change-over Board 240V set position.
3 Phase, 240 Volt
Single Phase, 139 Volt
The following connection, with the voltage change-over
board set into the 240V set position (See Figure 19), can
offer THREE PHASE power at 240V. After hooking up the
hard wires to the lugs as shown in figure 20 below, 240V
will be the voltage output.
The following connection, with the voltage change-over
board set into the 240V set position (See Figure 19), can
offer SINGLE PHASE power at 139V. After hooking up
the hard wires to the lugs as shown in figure 22 below,
139V will be the voltage output.
FIGURE 22. Hard Wire Hookup for Single Phase 139V
FIGURE 20. Hard Wire Hookup for Three Phase 240V
PAGE 38 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OUTPUTTERMINAL PANEL OVERVIEW
480 Volt Set position
Single Phase, 480 Volt
The voltage change-over board 480V set position uses all
6 plates in 3 different connection places. There are 2
plates at every position (Every plate is used). See figure
23 below.
The following connection, with the voltage change-over
board set into the 480V set position (See Figure 23), can
offer SINGLE PHASE power at 480V. After hooking up
the hard wires to the lugs as shown in figure 25 below,
480V will be the voltage output.
FIGURE 23. Voltage Change-over Board 480V set position.
FIGURE 25. Hard Wire Hookup for Single Phase 480V
3 Phase, 480 Volt
The following connection, with the voltage change-over
board set into the 480V set position (See Figure 23), can
offer THREE PHASE power at 480V. After hooking up the
hard wires to the lugs as shown in figure 24 below, 480V
will be the voltage output.
Single Phase, 277 Volt
The following connection, with the voltage change-over
board set into the 480V set position (See Figure 23), can
offer SINGLE PHASE power at 277V. After hooking up
the hard wires to the lugs as shown in figure 26 below,
277V will be the voltage output.
FIGURE 26. Hard Wire Hookup for Single Phase 277V
FIGURE 24. Hard Wire Hookup for Three Phase 480V
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — INSTALLATION
CAUTION
:
Outdoor Installation
An electric shock may happen when
vibrators are used. Pay close attention to
handling when operating vibrators and
always use rubber boots and gloves to
insulate the body from electrical shock.
Install the generator in a location where it will not be exposed
to rain or sunshine. Make sure the generator is on secure
level ground so that it cannot slide or shift around. Also
install the generator in a manner so that the exhaust will not
be discharged in the direction of nearby homes.
Generator Grounding
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from
excessive moisture. Failure to do will result in deterioration
of the insulation and will result in short circuits and grounding.
To guard against electrical shock and possible damage to
the equipment, it is important to provide a good EARTH
ground.
Article 250 (Grounding) of the National Electrical Code (NEC)
provides guide lines for proper grounding and specifies that
the cable ground shall be connected to the grounding system
of the building as close to the point of cable entry as
practical.
Foreign materials such as dust, sand, lint and abrasive
materials have a tendency to cause excessive wear to
engine and alternator parts.
NEC articles 250-64(b) and 250-66 set the following
grounding requirements:
CAUTION
:
1. Use one of the following wire types to connect the
generator to earth ground.
Pay close attention to ventilation when
operating the generator inside tunnels and
caves. The engine exhaust contains
noxious elements. Engine exhaust must
be routed to a ventilated area.
a. Copper - 10 AWG (5.3 mm2) or larger.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
2. When grounding the generator (Figure 27) connect the
ground cable between the lock washer and the nut on
the generator and tighten the nut fully.Connect the other
end of the ground cable to earth ground.
Indoor Installation
Exhaust gases from diesel engines are extremely poisonous.
Whenever an engine is installed indoors the exhaust fumes
must be vented to the outside.The engine should be installed
at least two feet from any outside wall. Using an exhaust
pipe which is too long or too small can cause excessive
back pressure which will cause the engine to heat
excessively and possibly burn the valves.
3. NEC article 250-52(c) specifies that the earth ground
rod should be buried a minimum of 8 ft. into the ground.
Mounting
The generator must be mounted on a solid foundation (such
as concrete) and set firmly on the foundation to isolate
vibration of the generator when it is running. The generator
must set at least 6 inches above the floor or grade level (in
accordance to NFPA 110, Chapter 5-4.1). DO NOT remove
the metal skids on the bottom of the generator. They are to
resist damage to the bottom of the generator and to maintain
alignment.
NOTE
When connecting the generator to any buildings
electrical system ALWAYS consult with a licensed
electrician.
PAGE 40 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — INSTALLATION
Figure 27. Typical Generator Grounding Application
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — PRE-SETUP
General Inspection Prior to Operation
Circuit Breakers
The DCA-400SSK generator has been thoroughly inspected
and accepted prior to shipment from the factory. However,
be sure to check for damaged parts or components, or loose
nuts and bolts, which could have occurred in transit.
To protect the generator from an overload, a 3-pole,1000
amp, main circuit breaker is provided to protect the UVW
output terminals from overload. In addition two single-pole,
20 amp GFCI circuit breakers are provided to protect the
GFCI receptacles from overload.Three 50 amp load circuit
breakers have also been provided to protect the load side of
the generator from overload. Make sure to switch ALL circuit
breakers to the "OFF" position prior to starting the engine.
Extension Cable
When electric power is to be provided to various tools or
loads at some distance from the generator, extension
cords are normally used. Cables should be sized to allow
for distance in length and amperage so that the voltage
drop between the generator and point of use (load) is held
to a minimum. Use the Cable Selection Guide (Table 10)
as a guide for selecting proper cable size.
NOTE
ALWAYS consult with a licensed
electrician for correct extension
cord wire size.
PAGE 42 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — PRE-SETUP
Lubrication Oil
Fuel
Fill the engine crankcase with lubricating oil through the filler Fill the fuel tank with clean and fresh diesel fuel. DO NOT
hole, but do not overfill. Make sure the generator is level. fill the tank beyond capacity.
With the dipstick inserted all the way, but without being screw
Pay attention to the fuel tank capacity when replenishing
into the filler hole, verify that the oil level is maintained
fuel. Refer to the fuel tank capacity listed on page 23,
between the two notches (Figure 28) on the dipstick. See
Table 11 for proper selection of engine oil.
Specification Table 7.
The fuel tank cap must be closed tightly after filling. Handle
fuel in a safety container. If the container does not have a
spout, use a funnel. Wipe up any spilled fuel immediately.
CAUTION
:
Never fill the fuel tank while the engine is
running or in the dark. Diesel spillage on a
hot engine can cause a fire or explosion.
If diesel spillage occurs, wipe up the
spilled diesel completely to prevent fire
hazards.
Coolant
Use only drinkable tap water. If hard water or water with
many impurities is used, the inside of the engine and radiator
may become coated with deposits and cooling efficiency
will be reduced.
Figure 28. Engine Oil Dipstick
When checking the engine oil, be sure to check if the oil is
clean and viscous. If the oil is not clean, drain the oil by
removing the oil drain plug, and refill with the specified amount
of oil as outlined in the Komatsu Engine Owner's Manual.
An anticorrosion additive added to the water will help prevent
deposits and corrosion in the cooling system. See the engine
manual for further details.
Table 11. Recommended Motor Oil
Temperature Range
Type Oil
104° F ~ 23° F
(40° C ~ -5°C)
SAE 30
23° F ~ 5° F
(-5° C ~ -15°C)
SAE 20 or SAE 10W-30
SAE 10W or SAE 10W-30
Below 5° C (-15°)
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — PRE-SETUP
Cleaning the Radiator
CAUTION :
The engine may overheat if the radiator fins become
overloaded with dust or debris. Periodically clean the radiator
fins with compressed air. Cleaning inside the machine is
dangerous, so clean only with the engine turned off and the
battery disconnected.
When adding coolant or antifreeze to the
radiator, do not remove the radiator cap
until the unit has completely cooled.
Day-to-day addition of coolant is done from the reserve tank.
When adding coolant to the radiator, DO NOT remove the
radiator cap until the unit has completely cooled. See Table
12 for engine, radiator, and reserve tank coolant capacities.
Make sure the coolant level in the reserve tank is always
between the "H" and the "L" markings.
Air Cleaner
Periodic cleaning/replacement is necessary. See
maintenance section for instruction to cleaning/replacing air
cleaner.
Fan BeltTension
A slack fan belt may contribute to overheating, or to
insufficient charging of the battery. Inspect the fan belt for
damage and wear. See maintenance section on replacing
belts. To adjust tension:
Table 12. Coolant Capacity
1. Insert a bar between alternator and the cylinder block to
fix alternator in position. When fixing the alternator in
position, insert a wooden block between the bar and
alternator to prevent damage to the alternator.
2. Loosen bolts and nuts located on the alternator.
3. Move alternator with the bar so the deflection of the belt
is approx. 8mm.
16.9 Gal. (64.0
Engine and Radiator
Liters)
Reserve Tank
2 Quarts (1.9 Liters)
4. Tighten the bolt and nuts to fix the alternator back to
position.
Operation in Freezing Weather
When operating in freezing weather, be certain the proper
amount of antifreeze (Table 13) has been added.
The fan belt tension is proper if the fan belt bends 7 to 10
mm (Figure 29) when depressed with the thumb as shown
below.
Table 13. Anti-Freeze Operating Temperatures
Freezing Point
Boiling Point
Vol %
Anti-Freeze
°C
-24
-37
°F
°C
°F
40
50
-12
-34
106
108
222
226
Figure 29. Fan Belt Tension
CAUTION
:
NOTE
Never place hands near the belts or fan
while the generator set is running.
When the antifreeze is mixed with
water, the antifreeze mixing ratio must
be less than 50%.
PAGE 44 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — PRE-SETUP
Battery Cable Installation
CAUTION
:
ALWAYS be sure the battery cables (Figure 30) are properly
connected to the battery terminals as shown below. The
RED cable is connected to the positive terminal of the battery,
and the BLACK cable is connected to the negative terminal
of the battery.
Inadequate battery connections may cause
poor starting of the generator, and create
other malfunctions.
Wiring
Inspect the entire generator for bad or worn electrical wiring
or connections. If any wiring or connections are exposed
(insulation missing) replace wiring immediately.
Piping and Hose Connection
Inspect all piping, oil hose, and fuel hose connections for
wear and tightness.Tighten all hose clamps and check hoses
for leaks.
If any hose (fuel or oil) lines are defective replace them
immediately.
Figure 30. Battery Connections
Battery
This unit is of negative ground DO NOT connect in reverse.
Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level is not
properly maintained. Add only distilled water when
replenishment is necessary.
CAUTION
:
If the battery cable is connected
incorrectly, electrical damage to the
generator will occur. Pay close attention
to the polarity of the battery when
connecting the battery.
The battery is sufficiently charged if the specific gravity of
the battery fluid is 1.28 (at 68°F). If the specific gravity
should fall to 1.245 or lower, it indicates the battery is
discharged and needs to be recharged or replaced.
Check to see whether the battery cables are loose. Poor
contact may result in poor starting or malfunctions. Always
keep the terminals firmly tightened. Coating the terminals
with a thin film of grease will help inhibit corrosion.
When connecting battery do the following:
1. DO NOT connect the battery cables to the battery
terminals when the Off/Manual/Auto switch is in either
the manual or auto position (ON). ALWAYS make sure
that the Off/Manual/Auto switch is in the OFF position
when connecting the battery.
2. Place a small amount of grease around both battery
terminals. This will ensure a good connection and will
help prevent corrosion around the battery terminals.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — LOAD APPLICATION
Single Phase Load
CAUTION
:
Motors and motor-driven equipment draw
much greater current for starting than
during operation.
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generator for operating the equipment.
An inadequate size connecting cable which
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
cannot carry the required load can cause a voltage drop
which can burn out the appliance or tool and overheat the
cable.
z
z
z
When connecting a resistance load such as an
incandescent lamp or electric heater, a capacity of up
to the generating set’s rated output (kW) can be used.
NOTE
If wattage is not given on the
equipment's name plate, approximate
wattage may be determined by
multiplying nameplate voltage by the
nameplate amperage.
When connecting a fluorescent or mercury lamp, a
capacity of up to the generating set’s rated output (kW)
multiplied by 0.6 can be used.
WATTS = VOLTAGE x AMPERAGE
When connecting an electric drill or other power tools,
pay close attention to the required starting current
capacity.
When connecting ordinary power tools, a capacity of up to
the generating set’s rated output (kW) multiplied by 0.8 can
be used.
The power factor of this generator is 0.8. See Table 14.
below when connecting loads.
CAUTION:
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch. Serious injury or death
may result without this transfer switch.
Table 14. Power Factor By Load
Type Of Load
Power Factor
Single-phase induction motors
0.4 - 0.75
Electric heaters, incandescent
lamps
1.0
0.4 - 0.9
1.0
NOTE
If output (kVA) is not given
on the equipment nameplate,
approximate output may be
determined by multiplying voltage by
Fluorescent lamps, mercury lamps
Electronic devices, communication
equipment
amperage by
and 1.732.
Three Phase Load
When calculating the power requirements for 3-phase power
use the following equation:
PAGE 46 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — GENERATOR START-UP PROCEDURE (MANUAL)
Jacket Water Heater and Internal Battery Charger 120
VAC Output Receptacles (OPTIONAL)
WARNING:
This generator is equipped with two 120VAC, 20 amp output
receptacles located on the output terminal panel, page 43,
Figure 14.
The engine's exhaust contains harmful
emissions. ALWAYS ventilate the
exhaust when operating inside tunnels,
excavations or buildings. Direct exhaust
away from nearby personnel.
The purpose of these receptacles is to provide power via
commercial power to the jacket water heater and internal
battery charger.
Before Starting
Engine
These receptacles will ONLY function when commercial
power has been supplied to them (Figure 31). To apply
commercial power to these receptacles, a power cord of
adequate size will be required.
1. Check the lubricating oil level prior to starting the engine.
Make sure the generator is level. The oil level must be
maintained between two notches on the dipstick.
2. When there is not enough lubricating oil, fill the crankcase
with high grade motor oil. Use a high quality detergent
oil classified CC or higher (See Table 11 on page 43).
When using the generator in hot climates there is no reason
to apply power to jacket water heater. However, if the
generator will be used in cold climates it is always a good
idea to apply power to the jacket water heater at all times.To
apply power to the jacket water heater simply apply power
to the jacket water heater receptacle via commercial power
using an power cord of adequate size.
3. Check the coolant level in the radiator and subtank.
Replenish with antifreeze as necessary.Always maintain
the coolant level between the FULL and LOW markings
on the coolant container. Be sure the radiator cap is
fastened securely.
If the generator will be used daily, the battery should normally
not require charging. If the generator will be idle (not used)
for long periods of time, apply power to the battery charger
receptacle via commercial power using an power cord of
adequate size.
4. Check the fuel level on the fuel gauge. If fuel is low, fill
the fuel tank with clean fresh unleaded automotive diesel.
If diesel spillage occurs, completely wipe up the spilled
fuel immediately.
When connecting the generator to a isolation (transfer)
switch, ALWAYS have power applied to the generator's
internal battery charger.This will ensure that the engine will
not fail due to a dead battery.
Before Starting
Generator and Control Panel
CAUTION:
NEVER start the engine with the main,
GFCI or load circuit breakers in the ON
position.
CAUTION:
ALWAYS have power applied to the
generator's internal battery charger
when connecting the generator to a
isolation (transfer) switch. Remember
before connecting this generator to
any buildings electrical system, have
a licensed electrician perform the
installation of the transfer switch.
1. Be sure to disconnect the electrical load and switch the
main, load and G.F.C.I. circuit breakers (Figure 31) to
the “OFF” position prior to starting the engine.
Figure 31. Main, GFCI and
Load Circuit Breakers
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — GENERATOR START-UP PROCEDURE (KEY SWITCH)
2. Connect the load to the UVW terminals as shown in 4. Close all engine enclosure doors (Figure 34).
Figure 32. These terminals can be found on the output
terminal panel, see page 35 Figure 14. To gain access
to the output terminals lift the UVW cover. Make sure to
tighten terminal nuts securely to prevent load wires from
slipping out.
Figure 34. Engine Enclosure Doors
5. Set the battery ON/OFF switch (Figure 35) to the ON
position.
Figure 32. UVW Terminal Lugs (Load)
3. Connect the negative battery cable (BLACK) to the
negative post on the battery (Figure 33).
Figure 35. Battery ON/OFF Switch
6. When starting the generator in COLD weather conditions,
press and hold the engine preheat button (Figure 36)
until the preheat lamp (Figure 37) is lit (ON).
TIVE
NEGA
POSTIVE
Y
TTER
BA
Figure 36. Engine Pre-Heat Button
Figure 33. Battery Connections
Figure 37. Engine Pre-Heat Lamp
PAGE 48 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — GENERATOR START-UP PROCEDURE (KEY SWITCH)
7. If the generator is equipped with a ignition switch, turn
the key to “Start” position (Figure 38). Once the engine
starts, release the key to the “on” position.
10. The ammeter (Figure 42) will indicate zero amps with no
load applied. When a load is applied, this meter will
indicate the amount of current that the load is drawing
from the generator’s alternator.
40
20
60
0
75
A
Figure 38. Engine Ignition Switch
Figure 42. Ammeter (No Load)
11. The engine oil pressure gauge (Figure 43) will indicate
the oil pressure (kg/ cm2) of the engine. Under normal
operating conditions the oil pressure should be
approximately 25 psi.
8. The generator's frequency meter (Figure 39) displays
the 60 cycle output frequency in HERTZ.
Figure 39. Frequency Meter (Hz)
9. The generator's voltage meter (Figure 40) displays the
120 VAC in VOLTS. If the voltage is not within the
specified frequency tolerance, use the voltage
adjustment control knob (Figure 41) to increase or
decrease the desired voltage.
Figure 43. Oil Pressure Gauge
12. The coolant temperature gauge (Figure 44) will indicate
the coolant temperature. Under normal operating
conditions the coolant temperature should be between
165 and 215 degrees Fahrenheit .
WATER TEMP
Figure 44. Coolant Temperature Gauge
Figure 40. Voltage Meter (Volts)
Figure 41. Voltage Adjust Control
Knob
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — GENERATOR START-UP PROCEDURE (KEY SWITCH)
13. The tachometer (Figure 45) will indicate the speed of
the engine when the generator is operating. Under normal
operating conditions this speed should be approximately
1800 RPM’s.
16. Observe the generator's ammeter (Figure 48) and verify
that it reads the anticipated amount of current with
respect to the load. Remember the ammeter will only
display a current reading if the load is in use.
40
20
60
0
75
A
Figure 48. Ammeter (Load)
Figure 45. Engine Tachometer
17. The generator will run until manually stopped or an
abnormal condition occurs.
14. Pull the throttle handle to increase the speed of the
engine (Figure 46).
Figure 46. Engine Throttle
15. Turn the MAIN, GFCI and LOAD circuit breakers to their
"ON" position (Figure 47).
Figure 47. Main and GFCI Circuit Breakers
PAGE 50 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — GENERATOR START-UP PROCEDURE (CONTROLLER)
Manual Start-up
1. Follow instructions as with key switch numbers 1-6.
Starting the generator in the "AUTO" mode is similar to
starting the generator in the "MANUAL" mode, with a few
exceptions.
2. Place the Off/Manual/Auto switch (Figure 49) in the
MANUAL position. Observe that the engine begins to
crank.
CAUTION:
When running the generator in the AUTO
mode, remember the generator can start
up at any time without warning. NEVER
attempt to perform any maintenance when
the generator is in the auto mode.
When starting generator in Auto mode use the "Manual Start-
up" procedure except where noted (see below).
Figure 49. Off/Manual/Auto Switch (Manual)
1. Perform steps 1 through 6 (Before Starting, page 47-
48) as outlined in the manual starting procedure.
3. After engine starts, verify that the "Engine Running"
status LED (Figure 50) on the Microprocessor Engine
Control Module (Engine Controller) display is "ON" (lit).
2. Apply commercial power to the internal battery charger
receptacle (to ensure good starting) via commercial
power. An external power cord will be required.
3. Apply commercial power to the jacket water heater
receptacle (not necessary for warm climates) via
commercial power. An external power cord will be
required.
4. Place the Off/Manual/Auto switch (Figure 51) in the
AUTO position.
Figure 50. Engine Controller Status LED
4. Continue instructions with key switch 8-17.
Auto Start-up
CAUTION:
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch. Serious injury or death
may result without this transfer switch.
Figure 51. Off/Manual Auto Switch
(AUTO)
5. Continue to follow the steps outline in the manual start-
up procedure (start at step 11, page 49).
CAUTION:
When connecting the generator to a
isolation (transfer) switch, ALWAYS have
power applied to the generator's internal
battery charger. This will ensure that the
engine will not fail due to a dead battery.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — GENERATOR SHUTDOWN PROCEDURE
Engine Shutdown
To shutdown the generator use the following procedure:
Emergency Stop
1. To stop the engine in the event of an emergency, PUSH
the emergency stop button ( Figure 54) inward.This button
is located on the generator's engine operating panel,
see page 30, Figure 11.
1. Place both the MAIN, GFCI and LOAD circuit breakers
to the "OFF position".
2. Let the engine cool by running it for 3-5 minutes with no
load applied.
3. Place the Off/Manual/Auto Switch (Figure 52) in the "OFF/
RESET" position
Figure 54. Emergency Stop Button
CAUTION
:
Figure 52. Off/Manual Auto Switch (OFF)
NEVER stop the engine suddenly except
in an emergency. DO NOT use the
emergency stop switch a as method of
shutting down the engine. This switch is
ONLY to be used in the event of an
emergency.
4. Verify that the "Engine Running" status LED (Figure 53)
on the microprocessor (Engine Controller) display is
"OFF" (not lit).
Figure 53. Engine Controller Running
Status LED (OFF)
5. Remove theload from the UVWO terminal strip (Figure 18
on page 48).
PAGE 52 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — MAINTENANCE
General Inspection
Fuel Addition
Prior to each use, the generating set should be cleaned and Add diesel fuel (the grade may vary according to season
inspected for deficiencies. Check for loose, missing or and locations). Always pour through the mesh filter.
damaged nuts, bolts or other fasteners. Also check for fuel Removing Water from theTank
or oil leaks.
Air Cleaner
After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally remove the drain
Every 50 hours: If dust indicator is red, clean the air cleaner cock and drain the contents. During cold weather, the greater
element.
Outer Element:
the empty volume inside the tank, the easier it is for water to
condense. This can be reduced by always keeping the tank
1. Loosen wing bolt, remove dust cup, then remove wing as full as possible.
nut and take out element. Air Removal
2. Clean the inside of the body and cover using a damp If air enters the fuel injection system of a diesel engine,
cloth.
starting becomes impossible. After running out of fuel, or
3. Blow dry with compressed air (0.69Mpa [7kgf.cm2, after disassembling the fuel system, bleed the system
99.4 PSI] maximum) against the side of the element according to the following procedure.
along the pleats. Then blow dry against outside along To restart after running out of fuel, turn the key switch to the
the pleats, then against inside again.
4. Remove one seal each time the element is cleaned.
“START” position for 15-30 seconds. Try again, if needed.
This unit is equipped with an automatic air bleeding system.
5. Replace the outer element after cleaning it 6 times or Service Daily
after one year. Replace the outer element if indicator is If engine is operating in very dusty and dry grass conditions,
red even after cleaning it.
a clogged air cleaner will result in high fuel consumption,
6. Check the inner cylinder element clamping nut for loss of power and excessive carbon buildup in the
looseness, and retighten if necessary.
7. If seal washer is damaged or the threads of wing nut are
damaged, replace.
8. Remove evacuator valve and clean it with compressed
air. Reinstall.
Inner element (if equipped)
1. Remove the cover and outer element, then remove the
inner element.
2. Cover the air connector opening (outer side) with clean
cloth or cloth tape.
3. Clean the inside of the body. Remove air connector
opening protection.
4. Install a new inner cylinder element to the cylinder and
tighten the nut.
5. Install element.
combustion chamber.
Cleaning the Fuel Strainer
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in diesel. Securely
fasten the fuel strainer cap so that fuel will not leak. Check
the fuel strainer every 200 hours of operation or once a month.
Check Oil Level
Check the crankcase oil level prior to each use, or when the
fuel tank is filled. Insufficient oil may cause severe damage
to the engine. Make sure the generator is level.The oil level
must be between the two notches on the dipstick as shown
in Figure 28, page 43.
Flushing Out Radiator and Changing Coolant
6. After replacing the element, press the button of the dust
indicator to return the red piston to its original position.
1. Stop the engine and allow to cool. Tighten valve of the
corrosion resistor (if equipped).
2. Turn water filer cap slowly and remove it.
3. Prepare a container to catch the coolant, then open drain
plug of the radiator or heat exchanger and drain plug of
the engine, and drain the coolant.
4. After draining the coolant, close drain plugs and fill with
tap water.
PAGE 54 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — MAINTENANCE
5. When the water level is near the mouth of the water Changing Oil
filler, open drain plugs and start the engine, and run at
low idling. Keep the engine running at low idling and
flush the radiator for about 10 minutes.
1. Make sure the oil is cool before changing.
2. Set a container directly under the drain plug of the oil
pan. Loosen the drain plug slowly.
6. Adjust the flow of the water flowing in and draining out to
ensure that the radiator is always full during the flushing
operation, While flushing water through the system,
watch carefully the water inlet hose does not come out
of the radiator filler port.
3. Check the drained oil for excessive metal particles or
foreign material. Contact the distributor if there is metal
particles or foreign material.
4. Using a filter wrench, turn filter cartridge to the left to
remove it. If the filter cartridge is filled with a large
amount of oil, wait 10 minutes or so before removing.
Make sure there is no old gasket stuck on the filter holder.
7. After flushing, stop the engine, open drain plug and drain
the water, then close drain plugs.
8. After draining the water, flush the system with a flushing
agent. See instructions on flushing agent label.
5. Tighten drain plug. Clean the filter holder, fill the new
filter cartridge with clean engine oil, coat the packing
and thread of the new filter cartridge with engine oil,
then install it to the filter holder. Tighten until the gasket
surface contacts the seal surface of the filter holder,
then tighten it a further 3/4 to 1 turn.
9. After flushing, open drain plugs and drain out all the
water, then close drain plugs and add tap water so the
water level is near the mouth of the water filler.
10. When the water level is near the mouth of the water
filler, open drain plugs and start the engine, run at low
idling and continue to flush the system until clean water
comes out. Adjust the flow of the water flowing in and
draining out to ensure the radiator is always full during
the flushing operation.
6. Add engine oil through oil filler until the oil level is between
the H and L marks on the dipstick.
7. Run the engine at idling for a short time, then stop the
engine. Recheck the oil level and fill as necessary.
Replacing fuel filter
11. When clean water comes out, stop the engine, drain all
the water, then close drain plugs.
1. Set the container under the filter cartridge to catch fuel.
2. Using a filter wrench, turn the filter cartridge to the left
to remove it.
12. Remove the corrosion resistor (if equipped) and open
valve.
3. Clean the filter holder, fill the new filter cartridge with
fuel, coat the packing surface of the filter cartridge with
engine oil, then install the cartridge to the filter holder.
13. Supply water until it flows over the water filler.
14. Drain the water inside reserve tank, clean the inside of
the reserve tank, then fill with coolant/water mixture to
between the full and low lines.
4. When installing, tighten until the packing surface
contacts the seal surface of the filter holder then tighten
a further 2/3 of a turn. If the filter cartridge is tighten too
much, the packing will be damaged and will cause fuel
leakage. Fuel leakage will occur if the filter cartridge is
not tightened enough. Always tighten to the correct
angle.
15. Stop the engine, wait for 3 minutes, add tap water until
the water level reaches near the water filer port, then
tighten the radiator cap.
Check Electric Heater (If equipped)
Before starting in cold weather (once a year), please contact
your Komatsu distributor for inspection. Remove electric
heater from the engine intake manifold and check for
disconnections or dirt. When checking or installing the electric
heater, replace the gasket with a new part.
5. After replacing filter cartridge, loosen air bleed plug.
6. Loosen the knob of feed pump, and pump it up and down
until no bubbles come our with the fuel from air bleed
plug.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — MAINTENANCE
7. After bleeding the air, tighten air bleed plug, then push in Generator Storage
the knob of feed pump and lock it in position.
8. Replace Corrosion resistor cartridge (if equipped)
9. Screw in valves at the top of the corrosion resistor.
For storage of the generator for over 30 days, the following
is required:
z
z
Fill the fuel tank completely, lubricate and change oil.
10. Using a filter wrench, turn the cartridge to the left to
remove it.
Disconnect the negative terminals of the battery and
cover it, or remove it from the machine and store it
separately.
11. Coat the seal surface of the new cartridge with engine
oil and install it to the filter holder.
z
If the ambient temperature is expected to drop below
0oC, add antifreeze to the radiator.
12. Tighten until he packing surface contacts the seal
surface of the filter holder, then tighten a further 2/3 of a
turn.
Removal from long term storage:
13. Open valves.
z
Apply oil to the engine valve and rocker arms, and
examine the operating condition of the valves.
Cleaning breather element
1. Loosen the clamp, then remove the hose and take out
breather. Wipe off the dirt around the breather. Check
the O-ring, and replace if necessary.
z
Remove the oil filler pipe from the turbocharger oil inlet
port, add 0.5-1L (0.13-0.26gal) of oil to the turbocharger,
reinstall the oil filler pipe.
2. Wash the breather in diesel fuel or flushing oil, blow dry
with compressed air, then reinstall it.
z
z
z
z
Change the oil in engine oil pan.
Replace all the filters.
3. Inspect the hose and if there is any deteriorated oil stuck
inside the hose. Replace hose if necessary.
Flush the inside of the cooling system.
Drain the water from the fuel tank and bleed the air from
the fuel system.
Greasing
Using a grease pump, grease the fan hub (1 place) and
tension pulley (2 places).
z
If the engine has not been started for more than one
year, contact your Komatsu distributor to have engine
overhauled.
PAGE 56 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — MAINTENANCE
TABLE 15.
10 Hrs
DAILY
250 Hrs
500 Hrs 1000 Hrs
INSPECTION / MAINTENANCE
Check Engine Fluid Levels
Check Air Cleaner
X
X
X
X
X
X
ENGINE
Check Battery Acid Level
Check Fan Belt Condition
Check for Leaks
Check for Loosening of Parts
Replace Engine Oil and Filter *1
Clean Air Filter
X
X
X
X
Drain Bottom of Fuel Tank
Clean Unit, Inside and Outside
Change Fuel Filter *2
X
X
Clean Radiator and Check Coolant
Protection Level
Replace Air Filter Element
Change Corrosion Resistor
Check all Hoses and Clamps
Clean Inside of Fuel Tank
X
X
X
X
Measure Insulation Resistance Over
3M ohms
X
GENERATOR
*1 Replace engine oil anf filter at 100 hours, first time only.
*2 Replace fuel filter at 250 Hours, first time only.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — GENERATOR WIRING DIAGRAM
PAGE 58 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENGINEWIRING DIAGRAM (KEY SWITCH)
PAGE 60 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENGINEWIRING DIAGRAM (CONTROLLER)
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper diagnosis based on the EngineTroubleshooting (Table 16).If
handling and maintenance inspections, but in the event of a the problem cannot be remedied, consult our company's
breakdown, use the tables shown for
business office or service plant.
TABLE 16. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
No fuel?
Replenish fuel.
Air in the fuel system?
Water in the fuel system?
Fuel pipe clogged?
Bleed system.
Remove water from fuel tank.
Clean fuel pipe.
Fuel filter clogged?
Clean or change fuel filter.
Excessively high viscosity of fuel
or engine oil at low temperature?
Use the specified fuel or engine oil.
Use the specified fuel.
Tighten nut.
Fuel with low cetane number?
Fuel leak due to loose injection
pipe retaining nut?
Engine does not start.
Incorrect injection timing?
Fuel cam shaft worn?
Adjust.
Replace.
Injection nozzle clogged?
Injection pump malfunctioning?
Clean injection nozzle.
Repair or replace.
Seizure of crankshaft, camshaft,
piston, cylinder liner or bearing?
Repair or replace.
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
Compression leak from cylinder?
Improper valve timing?
Piston ring and liner worn?
Excessive valve clearance?
Battery discharged?
Correct or replace timing gear.
Replace.
Adjust.
Charge battery.
Repair or replace.
Repair or replace.
Connect wiring.
Starter malfunctioning?
Key switch malfunctioning?
Wiring disconnected?
Starter does not run.
PAGE 62 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TROUBLESHOOTING (ENGINE)
TABLE 16. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Fuel filter clogged or dirty?
Air cleaner clogged?
SOLUTION
Clean or change.
Clean or change.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Repair or replace.
Adjust.
Injection pump malfunctioning?
Engine revolution is not smooth.
Incorrect nozzle opening
pressure?
Injection nozzle stuck or
clogged?
Repair or replace.
Fuel over flow pipe clogged?
Governor malfunctioning?
Excessive engine oil?
Clean.
Repair.
Reduce to the specified level.
Piston ring and liner worn or
stuck?
Repair or replace.
Either white or blue exhaust gas
is observed.
Incorrect injection timing?
Deficient compression?
Overload?
Adjust.
Adjust top clearance.
Lessen the load.
Use the specified fuel.
Clean or change.
Clean or change.
Repair or replace the nozzle.
Adjust.
Low grade fuel used?
Fuel filter clogged?
Either black or dark gray exhaust
gas is observed.
Air cleaner clogged?
Deficient nozzle injection?
Incorrect injection timing?
Engine's moving parts seem to
be seizing?
Repair or replace.
Deficient output.
Uneven fuel injection?
Repair or replace the injection pump.
Repair or replace the nozzle.
Deficient nozzle injection?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
Compression leak?
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TROUBLESHOOTING (GENERATOR/ENGINE)
Practically all breakdowns can be prevented by proper diagnosis based on the Engine and Radiator Troubleshooting
handling and maintenance inspections, but in the event of a (Table 17). If the problem cannot be remedied, consult our
breakdown, use the tables shown for
company's business office or service plant.
TABLE 17. GENERATOR TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Check output voltage using a voltmeter.
Check wiring and repair.
No Voltage Output
AC Voltmeter defective?
Is wiring connection loose?
Is AVR defective?
Replace if necessary.
Defective Rotating Rectifier?
Is engine speed correct?
Is wiring connections loose?
Defective AVR?
Check and replace.
Low Voltage Output
Turn engine throttle lever to "High".
Check wiring and repair.
Replace if necessary.
High Voltage Output
Is wiring connections loose?
Defective AVR?
Check wiring and repair.
Replace if necessary.
Circuit Breaker Tripped
Short Circuit in load?
Over current?
Check load and repair.
Confirm load requirements and reduce.
Check and replace.
Defective circuit breaker?
Over current Relay actuated?
Confirm load requirement and replace.
PAGE 64 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK —TROUBLESHOOTING (Engine Controller)
TABLE 18. ENGINE CONTROLLER TROUBLESHOOTING
Sympton
Possible Cause
Solution
Low oil pressure light is Low oil level?
on.
Fill oil level.
Oil pressure sending unit failure?
Replace oil pressure sending unit.
Refer to dealer.
Time delay malfuntion in Controller?
Wire shorted?
Inspect/repair wire.
Fill coolant level.
Low coolant level light
is on.
Low coolant level?
Sending unit failure?
Replace sending unit.
Replace/charge battery.
Tighten/replace fan belt.
Clean/repair radiator grill.
Close doors.
Low battery voltage?
High coolant
temperture light is on.
Fan belt tension incorrect?
Air flow is not circulation through radiator?
Doors open?
Exhaust leaking?
Replace/repair gaskets or faulty part.
Check/reduce load.
Replace thermostat.
Clear all air intakes.
Replace temperature switch.
Fill fuel level.
Generator being overloaded?
Thermostat failure?
Air intake blocked?
Temperature switch failure?
No or low Fuel?
Overcrank light is on.
Overspeed light is on.
Controller needs to be calibrated?
RPM engine speed too high?
Governor actuator needs to be adjusted?
Governor controller needs to be adjusted?
Controller needs to be calibrated?
Refer to dealer.
Adjust RPM.
Adjust governor actuator.
Adjust governor controller.
Refer to dealer.
Loss of MPU light(s) or Magnetic pick up out of adjustment?
Adjust magnetic pick up.
Clean magnetic pick up.
on.
Magnetic pick up dirty?
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #, +,
*
or %, belong to the same assembly or kit.
Note: If more than one of the same reference number is
listed, the last one listed indicates newest (or latest) part
available.
PAGE 66 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — SUGGESTED SPARE PARTS
DCA-400SSKW/KOMATSU SA6D140E-2
DIESEL ENGINE
1 to 5 Units
Description
Qty.
P/N
10 ...........6125817051 ......... AIR FILTER
10 ...........6003117111 ......... FUEL FILTER
10 ...........6002111231 ......... OIL FILTER
5 .............6004111171 ......... CARTRIDGE, CORROSION RESISTOR
1 .............0601804887 ......... CIRCUIT BREAKER ............................... UPTO S/N3706720
1 .............0601807514 ......... CIRCUIT BREAKER ............................... S/N3706721~
1 .............0601810575 ......... PILOT LAMP, ENGINE TROUBLE
1 .............0601810576 ......... PILOT LAMP, ENGINE TROUBLE
1 .............0412122258 ......... ENGINE FAN BELT
1 .............6008155390 ......... SWITCH, STARTER ............................... UPTO S/N3696509
5 .............615 ...................... KEY SET, STARTER SWITCH (2) .......... UPTO S/N3696509
2 .............0602122281 ......... OIL SWITCH
1 .............6212619610 ......... RADIATOR HOSE (UPPER)
1 .............6212616930 ......... RADIATOR HOSE (LOWER)
1 .............0605505030 ......... FUEL CAP
1 .............061820625........... AUTOMATIC VOLTAGE REGULATOR
1 .............0601807307 ......... MAIN CIRCUIT BREAKER
1 .............0601805840 ......... CIRCUIT BREAKER
1 .............0601802525 ......... HANDLE, MAIN CIRCUIT BREAKER .... UPTO S/N3706720
1 .............0601840073 ......... VOLTAGE REGULATOR (RHEOSTAT)
1 .............0601840009 ......... RHEOSTAT ............................................. S/N3701677~
2 .............0601840121 ......... KNOB, VOLTAGE REGULATOR
1 .............0601810072 ......... PILOT LAMP
2 .............0601810261 ......... BULB, PILOT LAMP
1 .............2016012191 ......... CAP, RADIATOR
1 .............0602122200 ......... UNIT, OIL PRESSURE
1 .............0602123206 ......... UNIT, WATER TEMPERATURE
1 .............0602121052 ......... CHARGING AMMETER
NOTE
Part number on this Suggested Spare
Parts list may supercede/replace the
P/N shown in the text pages of this
book.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK GENERATOR ASSY.
GENERATOR ASSY.
PAGE 68 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK GENERATOR ASSY.
GENERATOR ASSY.
NO.
1
2
PART NO.
C3110100202
PART NAME
QTY.
REMARKS
ROTOR ASSY.
FIELD ASSY.
RESISTOR 80W
1
1
2
3
0601842401
0601823282
0018205020
0040005000
0041205000
8201070002
8201611004
C3164200004
8201015003
0012116045
0042616000
0601000209
C3112500004
0071906315
8201614003
0012116040
0042516000
0012112040
0042512000
C3130100003
0226200495
8211323004
0223300172
8211323103
0221200440
0010110035
0041210000
C3132200003
0226000290
0225000590
0017106020
0601850144
C3154000002
C3138000003
0012110080
0042610000
0041210000
4
5
RECTIFIER ..................................................... 1 ......... RM50TC-24
HEX. SOCKET HEAD CAP SCREW
LOCKWASHER
PLAIN WASHER
FAN
COUPLING DISK
WASHER, COUPLING HUB
BALANCING PLATE
HEX. HEAD BOLT
LOCKWASHER
BALANCING WEIGHT KIT
BEARING FLANGE
BEARING
2
2
2
1
12
1
1
10
10
1
6
7
8
9
10
11
12
13
14
15
16
17
18
1
1
COUPLING RING
HEX. HEAD BOLT
LOCKWASHER
HEX. HEAD BOLT
LOCKWASHER
STATOR ASSY.
1
6
6
12
12
1
1
1
19
20
21
22
23
24
25
RUBBER SEAL
CLAMPER
RUBBER SEAL
CLAMPER
RUBBER SEAL
HEX. HEAD BOLT
PLAIN WASHER
COVER
1
1
1
2
2
1
26
27
28
29
30
31
32
33
RUBBER SEAL
RUBBER SEAL
HEX. HEAD BOLT
GROMMET
END BRACKET
FIELD ASSY. EXCITER
HEX. HEAD BOLT
LOCKWASHER
PLAIN WASHER
2
1
6
1
1
1
4
4
4
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK GENERATOR ASSY.
GENERATOR ASSY.
PAGE 70 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK GENERATOR ASSY.
GENERATOR ASSY.
NO.
34
35
35
37
PART NO.
PART NAME
QTY.
8
1
1
4
4
4
1
8
16
16
1
1
1
4
8
8
REMARKS
0017112045
C3154300104
C3154300004
0010106060
0040006000
0041206000
C3154400003
0017106016
0012112035
0042512000
C3132300003
0010106030
0041206000
0605000061
0030016000
0040016000
HEX. HEAD BOLT
COVER, BEARING
GASKET, BEARING
HEX. HEAD BOLT
LOCKWASHER
PLAIN WASHER
SUCTION COVER
HEX. HEAD BOLT
HEX. HEAD BOLT
LOCKWASHER
COVER, FAN
38
39
40
41
42
HEX. HEAD BOLT
PLAIN WASHER
RUBBER SUSPENSION
HEX. NUT
43
44
LOCKWASHER
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK CONTROL BOX ASSY.
CONTROL BO
PAGE 72 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
C3214000912
C3214001502
0601801170
0027106016
0601807307
0601807514
0601802525
C3214600004
0017108020
0021008045
0040008000
0041208000
0601820625
0027105016
0601820892
0027104016
C3274000003
8221852104
0017108030
C2277200004
8221853104
0801830804
0040016000
0041416000
0801830704
8201852504
0040012000
0041412000
0017110030
C3261500023
C3621501103
0017108020
0602201911
0027106015
0602200446
0017106015
0601824542
0027103010
C3224001303
C3224001203
C3224002403
0228800100
0228800110
0228800124
0228800165
0605011211
0601807622
0601806987
0601801040
0601806887
0601801041
0601810072
0601810261
CONTROL BOX............................................. 1 .......... S/N3692434 TO 3706720
CONTROL BOX............................................. 1 .......... S/N3706721~
CURRENT TRANSFORMER ........................ 3 .......... CW-5L 750/5A
2
3
4
MACHINE SCREW
6
CIRCUIT BREAKER, XS1200NE 1060A ...... 1 .......... S/N3692434 TO 3706720
CIRCUIT BREAKER, S7H 1000A.................. 1 .......... S/N3706721~; C0244300003
HANDLE, CIRCUIT BREAKER ..................... 1 .......... S/N3692434 TO 3706720
BRACKET, CIRCUIT BREAKER ................... 2 .......... S/N3692434 TO 3706720
HEX. HEAD BOLT .......................................... 4 .......... S/N3692434 TO 3706720
MACHINE SCREW ........................................ 4 .......... S/N3692434 TO 3706720
LOCK WASHER............................................. 4 .......... S/N3692434 TO 3706720
PLAIN WASHER ............................................ 4 .......... S/N3692434 TO 3706720
AUTOMATIC VOLTAGE REGULATOR......... 1 .......... NTA5A2T
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
MACHINE SCREW
OVER CURRENT RELAY.............................. 1 .......... THN20HZ
4
MACHINE SCREW
CHANGE-OVER BOARD, VOLTAGE
CHANGE TERMINAL
HEX. HEAD BOLT
TERMINAL PLATE
CHANGE PLATE
HEX. HEAD BOLT
LOCK WASHER
PLAIN WASHER
HEX. HEAD BOLT
HEX. HEAD BOLT
LOCK WASHER
PLAIN WASHER
HEX. HEAD BOLT
2
1
10
20
3
6
10
10
10
13
3
16
16
4
SET PANEL, ELECTRIC PARTS ................... 1 .......... S/N3692434 TO 3696509
SET PANEL, ELECTRIC PARTS ................... 1 .......... S/N3696510~
27
28
29
30
31
32
33
34
35
HEX. HEAD BOLT
4
UNIT, BATTERY SENSOR ............................ 1 .......... C7038A0000
MACHINE SCREW
1
EMERGENCY RELAY ................................... 1 .......... S/N3692434 TO 3701676; 6008151252
HEX. HAD BOLT ............................................ 4 .......... S/N3692434 TO 3701676
RELAY ............................................................ 2 .......... HH62S DC24V
MACHINE SCREW
CONTROL PANEL
4
1
CONTROL PANEL ........................................ 1 .......... S/N3692434 TO 3706720
CONTROL PANEL ........................................ 1 .......... S/N3706721~
RUBBER SEAL .............................................. 2 .......... S/N3692434 TO 3706720
RUBBER SEAL .............................................. 2 .......... S/N3706721~
RUBBER SEAL .............................................. 2 .......... S/N3692434 TO 3706720
RUBBER SEAL .............................................. 2 .......... S/N3706721~
36
37
38
39
40
41
42
43
44
PIN
2
FREQUENCY METER .................................. 1 .......... RSC-80F 45~65Hz 220V
AC AMMETER ............................................... 1 .......... RSS80 0~750A 0~1500A
CHANGE-OVER SW., AMMETER................. 1 .......... SL2AS
AC VOLTMETER ........................................... 1 .......... RSR80 0~600V
CHANGE-OVER SW., VOLTMETER ............. 1 .......... SL2VS
PILOT LAMP .................................................. 1 .......... LP132DC 220V
BULB
1
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK CONTROL BOX ASSY.
CONTROL B
PAGE 74 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO
45
46
47
48
49
50
PART NO
PART NAME
RHEOSTAT (VOLT. REGULATOR)............... 1 .......... RA20A2SE102BJ 2W 1K OHM
KNOB
QTY.
REMARKS
0601840073
0601840121
0601810161
0207004000
0601830710
C9221100004
0040008000
0041208000
0080200007
0017108040
3871824004
0041206000
0605110502
8221814804
0017108020
8224117004
0017108020
8221827704
0017108020
0017110035
0207010000
0601823861
0027104015
0601823240
0021004030
0040004000
0041204000
0601802149
0601802149
0601806671
0601802218
0027103020
LY2DC24V
1
PANEL LIGHT ................................................ 1 .......... V325070
HEX. NUT
2
1
2
2
2
2
4
1
1
1
1
8
1
4
1
8
4
4
PANEL LIGHT SWITCH
HEX. HEAD BOLT
LOCK WASHER
PLAIN WASHER
SNAP RING
51
52
53
54
55
56
57
58
59
60
61
HEX. HEAD BOLT
STOPPER, CONTROL PANEL
PLAIN WASHER
SNAP PIN
COVER, CONTROL BOX
HEX. HEAD BOLT
SIDE PANEL, CONTROL BOX
HEX. HEAD BOLT
PANEL, CONTROL BOX
HEX. HEAD BOLT
HEX. HEAD BOLT
HEX. NUT
62
63
64
65
ENGINE STOP UNIT ..................................... 1 .......... S/N3696510 TO 3701676
MACHINE SCREW ........................................ 2 .......... S/N3696510 TO 3701676
RECTIFIER .................................................... 4 .......... S/N3696510 TO 3701676; DE4503
MACHINE SCREW ........................................ 2 .......... S/N3696510 TO 3701676
LOCK WASHER............................................. 2 .......... S/N3696510 TO 3701676
PLAIN WASHER ............................................ 2 .......... S/N3696510 TO 3701676
FUSE, 10A ..................................................... 1 .......... S/N3696510 TO 3701676
FUSE, RIGHT (10A) ...................................... 1 .......... S/N3701677~
66
FUSE, LEFT (15A)......................................... 1 .......... S/N3701677~
HOLDER, FUSE ............................................ 1 .......... S/N3696510~
67
68
MACHINE SCREW ........................................ 2 .......... S/N3696510~
RELAY ............................................................ 1 .......... S/N3696510 TO 3701676;
REPLACES 0601823732
LY2DDC24V
PTF08A
RELAY ............................................................ 1 .......... S/N3699150~; REPLACES 0601827655
SOCKET ........................................................ 1 .......... S/N3696510~; REPLACES 0601823109
HOLDER ........................................................ 1 .......... S/N3696510~; PYCA1
MACHINE SCREW ........................................ 2 .......... DS/N3696510~
0601824400
0027104020
0601823706
0027104015
0601815402
0027104020
0601827396
ECU9988N
0601831340
0601830765
0602120498
0602202470
39
70
71
72
73
74
RELAY ............................................................ 1 .......... S/N3696510~
MACHINE SCREW ........................................ 2 .......... S/N3696510~
TERMINAL BOARD ....................................... 1 .......... S/N3696510~; TS144P
MACHINE SCREW ........................................ 2 .......... S/N3696510~
ENGINE CONTROLLER ............................... 1 .......... S/N3696510 TO 3699149
ENGINE CONTROLLER ............................... 1 .......... S/N3699150~; REPLACES 0602202545
SWITCH ......................................................... 1 .......... S/N3696510 TO 3698125; 82608DPDT
SWITCH ......................................................... 1 .......... S/N3698126~;S303T
SPEED SENSOR ........................................... 1 .......... S/N3696510~;DYNT11200
SEALED CABLE ............................................ 1 .......... S/N3696510~;TEHN23670201
75
76
77
78
79
80
81
DYN110654000024 CONTROLLER .............................................. 1 .......... S/N3701677~
0027104020
0601840009
C3262600004
0017106015
MACHINE SCREW ........................................ 4 .......... S/N3701677~
RHEOSTAT .................................................... 1 .......... S/N3701677~; RA20ASE502BJ
BRACKET ...................................................... 1 .......... S/N3701677~
HEX. HEAD BOLT .......................................... 2 .......... S/N3701677~
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK ENGINE & RADIATOR ASSY.
ENGINE & RADIATR AS
PAGE 76 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK ENGINE & RADIATOR ASSY.
ENGINE & RADIATOR ASSY.
NO.
1
PART NO.
C3924200054
PART NAME
QTY.
REMARKS
ENGINE .......................................................... 1 ......... S/N3692434TO 3701676;
KOMATSU SA6D 140E-2
C3925200004
6125817051
6002111231
6003117111
6004111171
0602040678
C3304200104
0010118060
0030018000
0040018000
0041218000
0605000061
0030016000
0040016000
6212619902
2016012191
6995619230
0010120055
0040020000
0041220000
C3311100204
0010112025
0040012000
0041212000
6212619610
6212616930
0726102612
6138619260
0728100909
0728101029
0728100489
0728100167
0802081003
0802010900
C3317100103
0199101150
0193601500
0605515013
0194700400
0194700450
0268500950
0605515074
C3327200004
ENGINE .......................................................... 1 ......... S/N3701677~; SA6D140E-2
ELEMENT, AIR CLEANER............................... 1......... REPLACES 0602040157
CARTRIDGE, OIL FILTER .............................. 1 ......... REPLACES 0602041146
CARTRIDGE, FUEL FILTER ........................... 1 ......... REPLACES 0602042157
CARTRIDGE, CORROSION RESISTOR ........ 1 ......... REPLACES 0602045144
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DUST SENSOR
ENGINE FOOT
HEX. HEAD BOLT
HEX. NUT
LOCKWASHER
PLAIN WASHER
RUBBER SUSPENSION
HEX. NUT
1
1
2
2
2
4
4
8
8
LOCKWASHER
RADIATOR ...................................................... 1 ......... REPLACES 0602011943
RADIATOR CAP
RUBBER SHEET ............................................ 2 ......... REPLACES 0605000085
1
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
HEX. HEAD BOLT
LOCKWASHER
PLAIN WASHER
BRACKET, RADIATOR
HEX. HEAD BOLT
LOCKWASHER
4
4
4
2
4
4
4
PLAIN WASHER
RADIATOR HOSE ........................................... 1 ......... REPLACES 0602013962
RADIATOR HOSE ........................................... 1 ......... REPLACES 0602014467
RADIATOR HOSE ........................................... 1 ......... REPLACES 0602013963
RADIATOR HOSE ........................................... 1 ......... REPLACES 0602013062
HOSE BAND ................................................... 6 ......... REPLACES 0602014056
HOSE BAND ................................................... 2 ......... REPLACES 0602014350
HOSE BAND ................................................... 2 ......... REPLACES 0602014351
HOSE BAND ................................................... 2 ......... REPLACES 0602014059
RESERVE TANK
1
CAP, RESERVE TANK .................................... 1 ......... REPLACES 0602010900
BRACKET, RESERVE TANK
HOSE
HOSE
HOSE BAND
HOSE
HOSE
HOSE
HOSE BAND
HOSE CLAMPER
1
1
1
2
1
1
1
2
1
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK ENGINE & RADIATOR ASSY.
ENGINE & RADIATOR ASSY.
PAGE 78 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK ENGINE & RADIATOR ASSY.
ENGINE & RADIATOR ASSY.
NO.
43
44
45
46
47
48
49
PART NO.
PART NAME
QTY.
REMARKS
8212044103
0017110025
C3358300204
0017110025
8212256104
0019208020
8215103504
OIL PANEL
1
2
1
2
1
2
1
HEX. HEAD BOLT
CLAMPER ROD
HEX. HEAD BOLT
CLAMPER ROD
HEX. HEAD BOLT
RUBBER SEAL
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSKENGINE OPERATING PANEL ASSY.
E EIEAS.
UPTO S/N 3701676
S/N 3701677~
PAGE 80 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
C3353100003
C2352100213
C2352100223
0017106015
0207006000
0602101000
0021008080
0030008000
0040008000
0041208000
0800250300
C3355100304
C3355200004
0017110025
0010010035
0030010000
0041210000
C3355300204
C3355300304
0602180106
0030008000
0207006000
0041206000
0041206000
0605010502
0602100049
0601830448
0602104045
0601831557
0602102055
0602120054
0602120156
0602122060
0602122200
0602123061
0602123206
0602121052
0602125060
0602115014
C3484000103
0010110030
0030010000
0040010000
0041210000
0601830710
OPERATING PANEL ................................ 1 .........S/N3692434TO 3696509
OPERATING PANEL ................................ 1 .........S/N3696510TO 3701676
OPERATING PANEL ................................ 1 .........S/N3701677
2
3
4
5
HEX. HEAD BOLT
HEX. NUT
BATTERY SWITCH .................................. 1 .........9827300090
MACHINE SCREW
HEX. NUT
LOCKWASHER
PLAIN WASHER
8
4
2
2
2
2
6
7
8
9
THROTTLE HANDLE................................ 1 .........S/N3692434TO 3701676
LINK, GOVERNOR ROD .......................... 1 .........S/N3692434TO 3701676
BRACKET ................................................ 1 .........S/N3692434TO 3701676
HEX. HEAD BOLT .................................... 2 .........S/N3692434TO 3701676
HEX. HEAD BOLT .................................... 1 .........S/N3692434TO 3701676
HEX. NUT ................................................. 1 .........S/N3692434TO 3701676
PLAIN WASHER....................................... 2 .........S/N3692434TO 3701676
GOVERNOR ROD .................................... 1 .........S/N3692434TO 3701676
GOVERNOR ROD .................................... 1 .........S/N3692434TO 3701676
BALL JOINT ............................................. 2 .........S/N3692434TO 3701676
HEX. NUT ................................................. 2 .........S/N3692434TO 3701676
HEX. NUT ................................................. 2 .........S/N3692434TO 3701676
PLAIN WASHER....................................... 2 .........S/N3692434TO 3701676
PLAIN WASHER....................................... 2 .........S/N3692434TO 3701676
SNAP PIN ................................................ 2 .........S/N3692434TO 3701676
STARTER SWITCH .................................. 1 .........S/N3692434TO 3696509;6008155390
PREHEAT BUTTON ................................. 1 .........S/N3696510~; AH25FB10
STOP BUTTON ........................................ 1 .........S/N3692434TO 3701676;0806410000
EMERGENCY STOP BUTTON ................ 1 .........S/N3701677~; AR22V2R01R
PRHEAT LAMP ........................................ 1 .........6008153730
TACHOMETER ......................................... 1 .........25000KX4110
CABLE, TACHOMETER ........................... 1 .........62500KA4210 L=3000
OIL PRESSURE GAUGE ......................... 1 .........42000KX1410
UNIT, OIL PRESSURE ............................. 1 .........53000AC0101
WATER TEMPERATURE GAUGE ............ 1 .........40000KX0910
UNIT, WATER TEMPERATURE ................ 1 .........41400KS0600
CHARGING AMMETER ........................... 1 .........43000KV0300
FUEL GAUGE .......................................... 1 .........41000KW0110
MONITOR ................................................. 1 .........V3376600000
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
SET FRAME
HEX. HEAD BOLT
HEX. NUT
LOCKWASHER
PLAIN WASHER
1
2
2
2
4
35
ENGINE SPEED SWITCH ....................... 1 .........S/N3701677~; S301T
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OUTPUTTERMINAL ASSY.
OUTPUT TERMINAL ASSY.
PAGE 82 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OUTPUTTERMINAL ASSY.
OUTPUT TERMINAL ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
1
8
REMARKS
8221860203
0801030404
0801830904
0039320000
0040020000
0041420000
3501860604
0019110050
0042310000
0042410000
0601804887
SET BOARD, OUTPUT TERMINAL
OUTPUTTERMINAL
HEX. HEAD BOLT
HEX. NUT
8
16
24
32
3
5
5
LOCKWASHER
PLAIN WASHER
TERMINAL PLATE
HEX. HEAD BOLT
LOCKWASHER
PLAIN WASHER
5
9
CIRCUIT BREAKER ..................................... 2 ........... S/N 3692434TO 3606720;
KM-51 265V 20A
REPLACES 0601805313
0601808803
0601805840
CIRCUIT BREAKER ...................................... 2 .......... S/N3606721~; QOU120B 20A
CIRCUIT BREAKER ..................................... 3 ........... S/N 3692434TO 3606720;
KM-52 265V 50A
10
0601808804
C1261600204
C3261600704
0223300200
0221200150
0017106020
0601812598
0601811034
0027104016
0030004000
0041204000
C3237100113
0019112045
0042412000
0805015604
0205012000
0845043704
C3237100214
0017108020
C0237101504
0805015604
0845054204
0017110040
0601815324
0027104020
0601850275
0601851780
CIRCUIT BREAKER ..................................... 3 ........... S/N3606721~; QOU250B 50A
BRACKET, CIRCUIT BREAKER ................... 1 ........... S/N 3692434TO 3606720
BRACKET, CIRCUIT BREAKER ................... 1 ........... S/N3606721~
RUBBER CUSHION ...................................... 1 ........... S/N 3692434TO 3606720
RUBBER CUSHION ...................................... 1 ........... S/N3606721~
11
12
13
14
15
16
HEX. HEAD BOLT
RECEPTACLE
2
2
RECEPTACLE ............................................... 3 ........... REPLACES 0601812565
MACHINE SCREW
HEX. NUT
10
10
10
1
2
2
PLAIN WASHER
COVER, OUTPUT TERMINAL
HEX. HEAD BOLT
PLAIN WASHER
STAY RUBBER
HEX. NUT
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
2
2
SPRING
COVER
2
1
HEX. HEAD BOLT
COVER, OUTPUT TERMINAL
STAY RUBBER
COLLAR
7
1
1
2
HEX. HEAD BOLT
2
TERMINAL BOARD ....................................... 1 .......... S/N3696510~
MACHINE SCREW ........................................ 2 .......... S/N3696510~
GROMMET .................................................... 1 .......... S/N3696510~
GROMMET .................................................... 2 .......... S/N3700680~
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — BATTERY ASSY.
BATTERY ASSY.
PAGE 84 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — BATTERY ASSY.
BATTERY ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
2
2
1
2
2
2
2
1
1
1
1
1
4
4
1
1
REMARKS
0168719052
0805018904
0805006404
0805006504
0037808000
0040008000
0041208000
C3347600004
C3347600104
C3347600304
C3347600204
C3347200004
0010010030
0030010000
0845040114
0845041004
0845040214
0845041104
0602220205
BATTERY
BATTERY SHEET
BATTERY BAND
BATTERY BOLT
WING NUT
LOCKWASHER
PLAIN WASHER
BATTERY CABLE
BATTERY CABLE
BATTERY CABLE
BATTERY CABLE
EARTH CABLE
HEX. HEAD BOLT
HEX. NUT
9
10
11
12
13
14
15
16
17
18
19
TERMINAL CAP
TERMINAL CAP
TERMINAL CAP
TERMINAL CAP
BATTERY SENSOR
1
1
1
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ACTUATOR ASSY.
ACTUATOR ASSY.
PAGE 86 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ACTUATOR ASSY.
ACTUATOR ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
QTY. REMARKS
DYNC11020300024
0602211090
C3356200004
0012310060
0016006070
0207006000
0040006000
0041206000
0602211091
0602180190
0602210092
0010106025
0207006000
0010106025
0207006000
0041206000
012310040
ACTUATOR ...........................................1 ......S/N3701677~;REPLACES 0602150092
LEVER ..................................................1 ......S/N3701677~;DYNC182
BRACKET, ACTUATOR .........................1 ......S/N3701677~
HEX. HEAD BOLT.................................2 ......S/N3701677~
HEX. SOCKET HEAD CAP SCREW ....4 ......S/N3701677~
HEX. NUT .............................................4 ......S/N3701677~
LOCKWASHER ....................................4 ......S/N3701677~
PLAIN WASHER ...................................4 ......S/N3701677~
ROD ......................................................1 ......S/N3701677~
BALL JOINT..........................................2 ......S/N3701677~
HEX. NUT .............................................2 ......S/N3701677~
HEX. HEAD BOLT.................................1 ......S/N3701677~
HEX. NUT .............................................1 ......S/N3701677~
HEX. HEAD BOLT.................................1 ......S/N3701677~
HEX. NUT .............................................1 ......S/N3701677~
PLAIN WASHER ...................................1 ......S/N3701677~
HEX. HEAD BOLT.................................1 ......S/N3701677~
5
6
7
8
9
10
11
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 87
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 88 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
1
4
2
1
1
8
1
2
4
8
4
8
4
4
4
1
1
4
4
4
8
2
4
4
4
4
7
7
REMARKS
C3331100102
0019210020
C3334200204
C3334200504
C3334200604
0019210025
C3334000103
0602320195
0010316080
0030316000
0042516000
0041616000
0010316050
0042516000
0041616000
8212355003
7432356104
0019112045
0030012000
0042312000
0042412000
8225125604
0019108020
0207008000
0042308000
0042408000
0019110030
0042310000
0042410000
MUFFLER
HEX. HEAD BOLT
PACKING
PACKING
PACKING
HEX. HEAD BOLT
EXHAUST PIPE
GASKET
HEX. HEAD BOLT
HEX. NUT
LOCKWASHER
PLAIN WASHER
HEX. HEAD BOLT
LOCKWASHER
PLAIN WASHER
OUTLET PIPE
GASKET
HEX. HEAD BOLT
HEX. NUT
LOCKWASHER
PLAIN WASHER
COVER
HEX. HEAD BOLT
HEX. NUT
LOCKWASHER
PLAIN WASHER
HEX. HEAD BOLT
LOCKWASHER
PLAIN WASHER
9
10
11
12
13
14
15
16
7
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 89
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 90 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
1
2
PART NO.
PART NAME
QTY.
REMARKS
C3364000603
0605505030
0601850590
0810105400
0264100385
0605515079
0605503020
0802120604
0605501050
0602021155
0027104010
8225523104
0805003414
0017108020
0037908000
0222100300
0130206000
3515512014
0603325011
0132006000
0845039604
0191303000
0191303000
0191004200
0605515019
0605515013
FUEL TANK
1
CAP, FUEL TANK ............................................ 1 ......... REPLACES 0605505005
KEY................................................................. 1 ......... REPLACES 0601850505
FUEL FILTER
HOSE, FUEL GAUGE
HOSE BAND
FUEL SENSOR
PACKING
UNIT, FUEL ..................................................... 1 ......... 52000-KA9810
PACKING ........................................................ 1 ......... 52391-KW3700
MACHINE SCREW
TANK BAND
PAD, TANK BAND
HEX. HEAD BOLT
HEX. NUT
TANK SHEET
STREET ELBOW
DRAIN PIPE
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
1
2
1
1
5
2
4
2
2
6
1
1
1
1
1
1
1
1
4
2
VALVE
PLUG
RUBBER SEAL
SUCTION HOSE
RETURN HOSE
RETURN HOSE
HOSE BAND
HOSE BAND
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 91
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #1 ASSY.
ENCLO
PAGE 92 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #1 ASSY.
ENCLOSURE #1 ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
C3414000202
C3414001902
C3414100104
C3414100004
0019208020
C3424001204
C3494100903
C3494101703
C342400103
C3494100903
C3494101703
C3424000202
C3494100903
C3494101703
C3424000302
C3494100903
C3494101703
0017108020
C3424300403
C3424300603
C3494100903
C3494101703
C3424300303
C3494100903
C3494101703
0019208020
0019210025
C3424201403
C3424201304
C3494101004
0019208020
BASE ............................................................. 1 .......... S/N3692434TO 3701676
BASE ............................................................. 1 .......... S/N3701677~
2
3
4
5
FLOOR PANEL
FLOOR PANEL
HEX. HEAD BOLT
FRONT FRAME
1
1
14
1
LINING ........................................................... 1 .......... S/N3692434TO 3701676
LINING ........................................................... 1 .......... S/N3701677~
FRONT FRAME
LINING ........................................................... 1 .......... S/N3692434TO 3701676
LINING ........................................................... 1 .......... S/N3701677~
FRONT FRAME
LINING ........................................................... 1 .......... S/N3692434TO 3701676
LINING ........................................................... 1 .......... S/N3701677~
FRONT FRAME
LINING ........................................................... 1 .......... S/N3692434TO 3701676
LINING ........................................................... 1 .......... S/N3701677~
HEX. HEAD BOLT
GUIDE PANEL, AIR ....................................... 1 .......... S/N3692434TO 3701676
GUIDE PANEL, AIR ....................................... 1 .......... S/N3701677~
LINING ........................................................... 1 .......... S/N3692434TO 3701676
LINING ........................................................... 1 .......... /N3701677
GUIDE PANEL, AIR
LINING ........................................................... 1 .......... S/N3692434TO 3701676
LINING ........................................................... 1 .......... S/N3701677~
HEX. HEAD BOLT
HEX. HEAD BOLT
COVER, FRONT FRAME
COVER, FRONT FRAME
LINING
6
7
8
1
1
1
9
10
20
11
1
12
13
14
15
24
8
1
1
1
16
HEX. HEAD BOLT
28
THE DEFAULT PART NUMBER FOR THE COLOR ORANGE.
PLEASE INDICATE COLOR WHEN ORDERING:
MQW-WHITE
MQGRN-GREEN
THE SERIAL NUMBER MAY BE REQUIRED.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 93
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #1 ASSY.
ENCLOSURE #1 ASSY.
PAGE 94 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #1 ASSY.
ENCLOSURE #1 ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
17
18
19
20
21
22
23
24
0845042703
0019208020
C3424201503
0019208020
0600500090
0021106020
C3434000202
0010120070
0030020000
0040020000
0041220000
0010120060
0030020000
0040020000
0041220000
C3464100102
0800251701
0025006015
0042306000
0042406000
0019208020
C3464501004
FILLER BRACKET
HEX. HEAD BOLT
COVER, FRONT FRAME
HEX. HEAD BOLT
EMBLEM
MACHINE SCREW
CENER FRAME
HEX. HEAD BOLT
HEX. NUT
LOCKWASHER
PLAIN WASHER
HEX. HEAD BOLT
HEX. NUT
LOCKWASHER
PLAIN WASHER
ROOF PANEL
1
4
1
14
1
2
1
6
6
6
12
8
8
8
16
1
1
2
2
2
25
26
27
28
FILLER COVER
MACHINE SCREW
LOCKWASHER
PLAIN WASHER
HEX. HEAD BOLT
29
30
28
BRACKET ...................................................... 2 .......... S/N3707481~
THE DEFAULT PART NUMBER FOR THE COLOR ORANGE.
PLEASE INDICATE COLOR WHEN ORDERING:
MQW-WHITE
MQGRN-GREEN
THE SERIAL NUMBER MAY BE REQUIRED.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 95
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #2 ASSY.
ENCLOSURE #2 ASSY.
THE DEFAULT PART NUMBER FOR THE COLOR ORANGE.
PLEASE INDICATE COLOR WHEN ORDERING:
MQW-WHITE
MQGRN-GREEN
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 96 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #2 ASSY.
ENCLOSURE #2 ASSY.
NO.
1
2
3
4
5
6
PART NO.
PART NAME
QTY.
1
1
2
1
22
1
1
11
4
3
1
1
3
18
1
REMARKS
C3444000903
8195151204
C3454700104
8175151204
0207006000
C3444000402
8225940104
0017108020
0019210025
0017110025
C3444300703
C3494300604
8195151004
0207006000
C3444300804
C3494300704
0017108020
0019208020
C3444200503
C3444200903
8225147004
0037906000
B9114500104
0207006000
B9114000102
0021806016
0030006000
8225146204
8225146304
0845050704
0207006000
0805011304
0805011204
0207006000
M9110100204
0845045004
0845047204
0845045004
0019208020
0601850097
0021008025
0845031504
REAR FRAME
LOUVER PANEL
LOUVER PANEL
LOUVER PANEL
HEX. NUT
REAR FRAME
LINING
HEX. HEAD BOLT
HEX. HEAD BOLT
HEX. HEAD BOLT
COVER, REAR FRAME
LINING
LOUVER PANEL
HEX. NUT
DUCT COVER
LINING
HEX. HEAD BOLT
HEX. HEAD BOLT
DOOR, REAR FRAME
DOOR, REAR FRAME
WINDOW PLATE
HEX. NUT
DOOR POCKET
HEX. NUT
DOOR HANDLE
MACHINE SCREW
HEX. NUT
7
8
9
10
11
12
13
1
14
15
16
17
18
19
20
21
22
23
12
15
1
1
2
12
1
4
1
4
4
1
1
4
8
1
1
4
24
25
26
27
28
29
30
31
DOOR ROD
DOOR ROD
STAY
HEX. NUT
STOPPER, DOOR
STOPPER, DOOR
HEX. NUT
HINGE ........................................................... 2 ........... REPLACES 0601850505
WASHER
HINGE
WASHER
HEX. HEAD BOLT
STOPPER
MACHINE SCREW
CAP
2
2
2
6
2
2
4
32
33
34
35
36
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 97
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #2 ASSY.
ENCLOSURE #2 ASSY.
PAGE 98 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #2 ASSY.
ENCLOSURE #2 ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
37
38
39
0600500090
0021106020
C3464200102
C3494500204
C3464500304
C3494500304
0017108020
0019208020
0019210025
C3464501104
EMBLEM
1
2
1
1
1
1
9
24
4
MACHINE SCREW
ROOF PANEL
LINING
COVER, ROOF PANEL
LINING
HEX. HEAD BOLT
HEX. HEAD BOLT
HEX. HEAD BOLT
40
41
42
43
44
BRACKET ..................................................... 2 ........... S/N3707481~
THE DEFAULT PART NUMBER FOR THE COLOR ORANGE.
PLEASE INDICATE COLOR WHEN ORDERING:
MQW-WHITE
MQGRN-GREEN
THE SERIAL NUMBER MAY BE REQUIRED.
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 99
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #3 ASSY.
ENCLOSURE #3 ASSY.
THE DEFAULT PART NUMBER FOR THE COLOR ORANGE.
PLEASE INDICATE COLOR WHEN ORDERING:
MQW-WHITE
MQGRN-GREEN
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 100 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #3 ASSY.
ENCLOSURE #3 ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
C3454201022
C3454201032
C3454201042
C3454202002
0019108065
0042308000
0042408000
C3454101203
C3494404704
C3454101303
C3494404704
C3454101903
C3494406304
C3454100703
C3494402204
C3454700504
C3454301004
C3494404804
0207006000
C3454003103
C3494406604
C3454003003
C3494406404
C3454002103
C3494404504
C3454001603
C3494402704
8195151004
8215151004
0207006000
C3454301403
C3494406704
C3454301304
C3494406504
C3454300904
C3494404604
0207006000
B9114000002
0021806016
0030006000
SPLASHER PANEL....................................... 1 ........... S/N3692434TO S/N3696509
SPLASHER PANEL....................................... 1 ........... S/N3696510TO 3700679
SPLASHER PANEL....................................... 1 ........... S/N3700680TO 3706720
SPLASHER PANEL....................................... 1 ........... S/N3706721
2
HEX. HEAD BOLT
LOCKWASHER
PLAIN WASHER
SIDE PANEL
LINING
SIDE PANEL
LINING
SIDE PANEL
LINING
SIDE PANEL
LINING
LOUVER PANELL
DUCT
LINING
HEX. NUT
SIDE DOOR
LINING
SIDE DOOR
LINING
SIDE DOOR
LINING
SIDE DOOR
LINING
LOUVER PANEL
LOUVER PANEL
HEX. NUT
DUCT
LINING
DUCT
LINING
DUCT
6
6
6
1
1
1
1
1
1
1
1
3
3
3
27
1
1
1
1
1
1
1
1
4
1
30
1
1
2
2
1
1
35
3
28
16
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
LINING
20
21
23
HEX. NUT
DOOR HANDLE
MACHINE SCREW
HEX. NUT
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 101
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #3 ASSY.
ENCLOSURE #3 ASSY.
THE DEFAULT PART NUMBER FOR THE COLOR ORANGE.
PLEASE INDICATE COLOR WHEN ORDERING:
MQW-WHITE
MQGRN-GREEN
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 102 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — ENCLOSURE #3 ASSY.
ENCLOSURE #3 ASSY.
NO.
24
PART NO.
PART NAME
HINGE
WASHER
HINGE
WASHER
HEX. HEAD BOLT
STOPPER
MACHINE SCREW
HEX. HEAD BOLT
LOCKWASHER
PLAIN WASHER
CAP
QTY.
11
11
11
11
57
10
10
8
REMARKS
0845046904
0845045004
0845047004
0845045004
0019208020
0601850097
0021008025
0019108065
0042308000
0042408000
0845031504
25
26
27
28
29
8
8
22
30
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 103
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — RUBBER SEAL ASSY.
PAGE 104 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — RUBBER SEAL ASSY.
RUBBER SEAL ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
QTY.
REMARKS
0228901390
0228900825
0228900790
0229201400
0228800795
0221200795
0228801240
0229201340
0228100120
0228100510
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
6
8
2
2
5
RUBBER SEAL ................................................ 2......... S/N3692434TO 3701676
RUBBER SEAL ................................................ 2......... S/N3701677~
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
6
7
8
9
2
1
4
4
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 105
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OIL PIPING ASSY.
OIL PIPING ASSY.
PAGE 106 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — OIL PIPING ASSY.
OIL PIPING ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
PUMP
BRACKET, PUMP
HEX. HEAD BOLT
BUSHING
NIPPLE
VALVE
HOSE JOINT
HOSE JOINT
PACKING
HOSE
HOSE BAND
HOSE
QTY.
REMARKS
0602023040
8215191013
0017106025
7522054204
0131506000
0120006005
0602022202
3972054104
3972054304
0265801650
0605515074
0193301200
0605515004
1
1
5
1
1
1
1
1
1
1
2
1
1
9
10
11
12
13
HOSE BAND
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 107
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — NAME PLATE AND DECALS
NAME PLATE AND DECALS
CONTROL BOX GROUP
S/N3701677~
PAGE 108 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — NAME PLATE AND DECALS
NAME PLATE ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
0800655603
C1551000503
C1552000403
B1552000103
C9522100003
DECAL: HANDLING PROCEDURES .............. 1 ......... S-2763A;S/N3692434TO 3696509
DECAL; HANDLING PROCECURES .............. 1 ......... C15100050;S.N3696510TO 3701676
DECAL; HANDLING PROCDURES ................. 1 ......... C15200040;S/N3701677~
DECAL;CAUTION ........................................... 2 ......... B15200010;S/N UPTO 3701676
DECAL;CAUTION ........................................... 2 ......... C92210000; S/N 3701677~
2
CONTROL BOX GROUP
3
4
5
6
7
8
9
10
11
12
13
14
15
0800520100
0800520904
0800520814
0840624504
0840624604
0840624704
0840624804
B9531100604
C0551000903
C2551000004
C3561101103
C9502400004
0600500091
PLATE: ON-OFF .............................................. 1 ......... AT-202
PLATE: AMMETER CHNG.-OVER SWTH. ..... 1 ......... N-2438
PLATE: VOLTMETER CHNG.-OVER SWTH. .. 1 ......... N-2439
DECAL: CIRCUIT BREAKER .......................... 1 ......... S-3031
DECAL: PANEL LIGHT SWITCH..................... 1 ......... S-3032
DECAL: PILOT LAMP ..................................... 1 ......... S-3033
DECAL:VOLTAGE REGULATOR..................... 1 ......... S-3034
DECAL:WARNING .......................................... 1 ......... B93110060
DECAL: OUTPUT VOLTAGE SETTING........... 1 ......... C05100090
DECAL: SAFTETY INSTRUCTIONS............... 1 ......... C25100000
DECAL:WHISPERWATT 400 .......................... 1 ......... C36110110
DECAL; HIGH IDLE SPEED ........................... 1 ......... S/N3701677~;C9024000
DECAL; ENGINE CONTROLLER .................... 1 ......... S/N3696510~
ENGINE OPERATING PANEL GROUP
19
20
0840625004
C1552000013
0840625104
C9501400304
C0551000504
C0551000704
C0551000804
0840647804
DECAL: PREHEAT LAMP ............................... 1 ......... S/N3692434 TO 3701676;S-3036
DECAL; OPERATING PANEL.......................... 1 ......... S/N3701677~; C15200001
DECAL: STARTER SWITCH ........................... 1 ......... S/N3692434TO 3696509;S-3037
DECAL; PREHEAT BUTTON........................... 1 ......... S/N3696510TO 3701676;C90140030
DECAL: BATTERY SWITCH ........................... 1 ......... C05100050
21
22
23
DECAL: LOW - HIGH ...................................... 1 ......... S/N3692434TO 3696509;C05100070
DECAL: STOP BUTTON ................................. 1 ......... S/N3692434TO 3696509;C05100080
DECAL; EMERGENCY STOP ......................... 1 ......... S/N3696510TO 3701676;S4100
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 109
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — NAME PLATE AND DECALS
NAME PLATE AND DECALS
BATTER
ROUP
PAGE 110 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSK — NAME PLATE AND DECALS
NAME PLATE ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
ENGINE & RADIATOR GROUP
16
17
18
6360610304
B9504000404
B9504100104
DECAL:WATER............................................... 1 ......... S-1880
DECAL:WARNING .......................................... 2 ......... B90400040
DECAL:WARNING .......................................... 1 ......... B90410010
OUTPUTTERMINAL GROUP
24
25
26
0840614104
0840619904
B4551000103
C1551000803
B9511100304
B9511100404
B9531100504
C0551000404
9039209064
DECAL: GROUND ........................................... 1 ......... S-2635
DECAL:DANGER............................................ 1 ......... S2731
DECAL: RECEPTACLE & CIRCUIT BREAK ... 1 ......... S/N3692434TO 3706720;B45100010
DECAL; RECEPTACLE & CIRCUIT BREAK ... 1 ......... S/N3706721~;C15100080
DECAL:WARNING .......................................... 1 ......... B91110030
DECAL:WARNING .......................................... 1 ......... B91110040
DECAL:WARNING .......................................... 1 ......... B93110050
DECAL: 3-PHASE OUTPUT TERMINAL......... 1 ......... C05100040
DECAL; START CONTACT.............................. 1 ......... S/N3696510; S4468
27
28
29
30
31
BATTERY GROUP
32
33
34
0800689404
0800689504
C9505300004
DECAL: + ........................................................ 1 ......... S-2090
DECAL: - ......................................................... 1 ......... S-2091
DECAL;CAUTION ........................................... 1 ......... C90530000
MUFFLER GROUP
DECAL:WARNING ...........................................1......... B90420000
DECAL : CAUTION...........................................1......... B91110020
35
36
B9504200004
B9511100204
FUELTANK GROUP
37
38
39
1320620904
6360620004
B9504500004
DECAL: DIESEL FUEL ....................................1......... S-1756
DECAL: FUEL DRAIN PLUG............................1......... S-1883
DECAL:WARNING ...........................................1......... B90450000
BONNET GROUP
40
41
42
43
44
45
46
47
48
49
50
1320610603
1320621504
0840625902
B9504000304
C3561101003
C3561100903
C3561100604
C3561100803
C3561100104
C3561100703
C3561100203
DECAL: WATER - OIL.......................................1......... S-1760
DECAL: SUPPORT HOOK...............................2......... S-2257
DECAL: MQ......................................................1......... S-3057
DECAL:CAUTION ............................................1......... B90400030
STRIPE
STRIPE
STRIPE
STRIPE
STRIPE
STRIPE
STRIPE
1
1
2
1
2
1
1
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 111
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
Effective: July 1, 2000
PAYMENT TERMS
4. Freight is at the sender’s expense. All PRICINGANDREBATES
partsmustbereturnedfreightprepaidto
Multiquip’sdesignatedreceivingpoint.
Terms of payment for parts are net 10 days.
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspecific
5. Parts must be in new and resalable dateandallordersreceivedonorafterthatdate
condition,intheoriginalMultiquippackage willbebilledattherevisedprice. Rebatesfor
(ifany),andwithMuiltiquippartnumbers price declines and added charges for price
FREIGHTPOLICY
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifest has been obtained from the carrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
clearlymarked.
increaseswillnotbemadeforstockonhandat
thetimeofanypricechange.
6. Thefollowingitemsarenotreturnable:
Multiquip reserves the right to quote and sell
directtoGovernmentagencies,andtoOriginal
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
a. Obsolete parts. (If an item is listed
inthepartspricebookasbeing
replaced by another item, it is
obsolete.)
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
andotherrubberparts)thatwere
purchasedmorethansixmonths
priortothereturndate.
MINIMUMORDER
SPECIALEXPEDITINGSERVICE
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
A$20.00to$50.00surchargewillbeaddedto
theinvoiceforspecialhandlingincludingbus
c. Anylineitemwithanextendeddealer shipments, insured parcel post or in cases
netpriceoflessthan$5.00.
where Multiquip must personally deliver the
partstothecarrier.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
Returnshipmentswillbeacceptedandcredit
will be allowed, subject to the following
provisions:
LIMITATIONSOFSELLER’SLIABILITY
f.
Paint,chemicals,andlubricants.
Multiquip shall not be liable here under for
damagesinexcessofthepurchasepriceofthe
itemwithrespecttowhichdamagesareclaimed,
andinnoeventshallMultiquipbeliableforloss
of profit or good will or for any other special,
consequentialorincidentaldamages.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
1. AReturnedMaterialAuthorizationmust
beapprovedbyMultiquippriortoshipment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Sales that defines item numbers, 8. Such material will be held for 5 working
quantities,anddescriptionsoftheitemsto
bereturned.
days from notification, pending
instructions. If a reply is not received
within5days,thematerialwillbereturned
tothesenderathisexpense.
LIMITATIONOFWARRANTIES
a. Thepartsnumbersanddescriptions
mustmatchthecurrentpartsprice
list.
Nowarranties,expressorimplied,aremadein
connection with the sale of parts or trade
accessories nor as to any engine not
manufacturedbyMultiquip.Suchwarranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes not
authorizes any person to assume for it any
other obligation or liability whatever in
connectionwiththesaleofitsproducts.Apart
fromsuchwrittenstatementofwarranty,there
arenowarranties,express,impliedorstatutory,
which extend beyond the description of the
productsonthefacehereof.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. Thelistmuststatethereason(s)for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhich
theitemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. Thelistmustincludethenameand
phonenumberoftheperson
requestingtheRMA.
3. A copy of the Return Material
Authorizationmustaccompanythereturn
shipment.
PAGE 112 — DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
DCA-400SSK — PARTS AND OPERATION MANUAL (STD)— REV. #3 (09/17/01) — PAGE 113
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HANDWHEN CALLING
PARTS DEPARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
SERVICE DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
Manufactured for Multiquip Inc.
by
DENYO MANUFACTURING, CO., USA
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
E-MAIL:mq@multiquip.com
WWW:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Miele Clothes Dryer T 4882 C User Manual
Miele Washer W 3514 WPS User Manual
Napoleon Fireplaces Stove EPA 1100 User Manual
NEC Video Game Console EA221WME User Manual
Nesco Kitchen Utensil fs km User Manual
NETGEAR Network Card WN511T User Manual
Oreck Vacuum Cleaner compact canister Vaccum User Manual
OWI Speaker System MCRC303 User Manual
PAC Speaker System OEM 2 User Manual
Panasonic Switch AW SW350 User Manual