OPERATION AND PARTS MANUAL
MODEL V304
VIBRATORY ROLLER
Revision #8 (11/13/09)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Proposition 65 Warning ............................................. 2
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Explanation Of Code In Remarks Column .............. 34
Suggested Spare Parts ........................................... 35
Name Plate and Decals ..................................... 36-37
Cocoa Mat Assy. ................................................ 38-39
Travel Linkage Assy. .......................................... 40-41
Vibratory Linkage ............................................... 42-43
Handle Assy. ...................................................... 44-45
Chassis Assy ...................................................... 46-47
Transport Hooks Assy. ....................................... 48-49
Pump Drive Assy. ............................................... 50-51
Vibratory Drive Assy. .......................................... 52-53
Vibratory Roll Assy. ............................................ 54-55
Battery Assy. ...................................................... 56-57
Spray Assy. ........................................................ 58-59
Transmission Assy.............................................. 60-61
Multiquip V304 — Vibratory
Roller
Safety Message Alert Symbols .............................. 6-7
Rules For Safe Operation ...................................... 8-9
Operation and Safety Decals .................................. 10
Specifications .......................................................... 11
Roller Dimensions .............................................. 12-13
Roller Components ............................................ 14-16
Roller Components ............................................ 17-18
General Information ................................................ 19
Inspection........................................................... 20-22
Initial Start-Up (Engine) ..................................... 23-24
Operation ........................................................... 25-26
Maintenance ...................................................... 27-29
Preparation For Long Term Storage ....................... 30
Troubleshooting (Roller).......................................... 31
Troubleshooting (Engine)................................... 32-33
Specification and part number are subject
to change without notice.
PAGE 4 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
N View Parts Diagrams
N Order Parts
N Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
Order via Phone:
1-800-427-1244
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
R
Dealer Account Number
R
Specify Preferred Method of Shipment:
R
R
R
R
R
Dealer Name and Address
ꢀ UPS/Fed Ex
ꢀ DHL
ꢀ Truck
N
N
Priority One
Ground
Shipping Address (if different than billing address)
Return Fax Number
N Next Day
Second/Third Day
Applicable Model Number
N
Quantity, Part Number and Description of Each Part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when
operating this equipment. Failure to read and understand the
Safety Messages and Operating Instructions could result in
injury to yourself and others.
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
NOTE
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
This Owner's Manual has been developed to provide
complete instructions for the safe and efficient operation
of the Multiquip Model V304 Vibratory Roller. Refer to the
engine manufacturers instructions for data relative to its
safe operation.
Before using this vibratory roller, ensure that the
operating individual has read and understands all
instructions in this manual.
Explosive Fuel
GASOLINE is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
Burn Hazards
DANGER: You WILL be KILLED or
SERIOUSLY injured if you do not follow
directions.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. Never operate the engine with heat
shields or heat guards removed.
WARNING: You CAN be KILLED or
SERIOUSLY injured if you do not follow
directions.
Rotating Parts
CAUTION: You CAN be injured if you
do not follow directions.
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
Potential hazards associated withV304 vibration roller operation
will be referenced with Hazard Symbols which appear
throughout this manual, and will be referenced in conjunction
with Safety Message Alert Symbols.
PAGE 6 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the engine ON/OFF switch in
the OFF position, and remove the ignition key
when the machine is not in use.
ALWAYS wear approved respiratory
protection.
Equipment Damage Messages
Sight and Hearing hazard
Other important messages are provided throughout this manual
to help prevent damage to your trash pump, other property, or
the surrounding environment.
ALWAYS wear approved eye and hearing
protection.
NOTE
This compaction roller, other property, or the
surrounding environment could be damaged
if you do not follow instructions.
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
NEVER touchthehotexhaustmanifold,
muffler or cylinder.Allow these parts to
cool before servicing engine or pump.
CAUTION:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only!This equipment is for
industrial use only.
The following safety guidelines should always be used when
operating theV304Vibration Roller:
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
GENERAL SAFETY
■
DO NOT operate or service this equipment before
readingthisentiremanual.
The engine of this roller requires an adequate free flow of
cooling air. Never operate
the roller in any enclosed
or narrow area where free
flow of the air is restricted. If
the air flow is restricted it
will cause serious damage
to the pump or engine and
may cause injury to people
and property. Remember
the roller's engine gives off
DEADLY gases.
■
■
This equipment should not be operated by
persons under 18 years of age.
NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steel-
toed boots and other protective devices required
by the job.
■
■
NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
NEVER operate this equipment under the
influence or drugs or alcohol.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a hot
engine.
■
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■
■
NEVER operate the vibration roller in
an explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■
■
■
Manufacture does not assume responsibility for any accident
due to equipment modifications.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Topping-off to filler port is dangerous, as it tends to spill fuel.
ALWAYS check the machine for loosened threads or bolts
before starting.
PAGE 8 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
■
■
■
NEVER Run engine without air cleaner. Severe engine
■
High Temperatures – Always stop engine and allow the
engine to cool before adding fuel, oil or performing service
and maintenance functions. Contact with hot components can
cause serious burns.
damage may occur.
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
■
■
NEVER engage the "free wheel engagement lever" when
parked on an incline.
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using pump.
NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■
■
■
■
■
DO NOT operate this roller with hydrostatic oil temperature
higher than 180 degrees Fahrenheit.
NEVER leave the roller unattended, turn off engine and place
lock handle in upright position.
Emergencies
■
ALWAYS know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department. This information will be
invaluable in the case of an emergency.
CAUTION must always be observed while servicing this roller.
Rotating parts can cause injury if contacted.
DO NOT leave roller with engine running. Use chock blocks
if parking roller on a grade.
NEVER ride on a walk-behind roller in unshored trenches or
near steep, unsupported banks.The vibration caused by the
roller could cause a cave-in.
Maintenance Safety
■
NEVER lubricate components or attempt service on a running
■
ALWAYS use extreme care when walking behind the roller,
avoid having your feet or clothing getting caught under the
dolly wheels or roller.
machine.
■
ALWAYS allow the machine a proper amount of time to cool
before servicing.
■
■
Whenever possible try and stand to one side of the roller
rather than directly behind it.
■
■
Keep the machinery in proper running condition.
ALWAYS use extreme care when operating near obstructions,
on slippery surfaces, grades and side slopes.
Fix damage to the machine immediately and always replace
broken parts.
■
■
ALWAYS wear slip resistant safety shoes or boots.
■
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
Unauthorized equipment modifications will void all
warranties.
DO NOT use food or plastic containers to dispose of
hazardous waste.
■
■
Uneven grades can cause the handle to raise or lower
unexpectedly, striking the operator by surprise.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
When working on slopes, avoid sidehill travel whenever
possible. Operate up and down travel only. Remember, the
danger of sliding on and/or tripping on steep slopes is always
present
Lifting
■
The roller has an operating weight of approximately 1,045
lbs. (474 Kg). Use lifting equipment capable of lifting this
weight.
■
■
NEVER ride on a walk-behind roller unless it is designed to
accommodate riders and an appropriate seat is provided.
Refer to the Engine Owner's Manual for engine technical
questions or information.
■
ALWAYS check the roller's transport hooks. Make sure the
hooks are secure and tight before lifting the machine.
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND SAFETY DECALS
Machine Safety Decals
The V304 Compaction Roller is equipped with a number of safety decals. These decals are provided for operator safety and
maintenance information.The illustration below and on the next page shows these decals as they appear on the machine.Should
any of these decals become unreadable, replacements can be obtained from your dealer.
P/N 511782
ESSICK
SAFETY INSTRUCTIONS
A MULTIQUIP COMPANY
1. Do not operate or service this machine before reading
the operating and maintenance manual.
2. Keep all inexperienced and/or unauthorized people away from
WARNING
To avoid injury,
you MUST read
and understand
operator’s manual
before using this
machine.
equipment at all times
3. Do not operate this equipment unless all guards and safety
devices are attached and in place.
4. Keep this equipment in safe operating at all times.
5. Caution must be exercised while servicing this equipment.
Rotating and moving parts can cause injury if contacted.
6. Stop engine and allow to cool before adding fuel or oil.
7. Stop engine when leaving equipment.
This machine to
be operated by
qualified
8. Block unit when parking on a slope.
9. Unauthorized equipment modifications will void all warranties.
personnel only.
Ask for training
as needed.
ESSCICK CONSTRUCTION PRODUCTS A MULTIQUIP COMPANY CARSON, CALIFORNIA
P/N 35137
948501
OFF
V
I
B
R
A
T
USE COCOA MAT ONLY
WHEN ROLLING ASPHALT
F
O
R
W
A
R
E
V
E
R
S
E
LIFT FROM ROLL
WHEN NOT REQUIRED
948044
R
D
511769
I
511766
511767
CAUTION
ATTACH SAFETY CHAIN
DURING TRANSPORT
O
N
ON
WATER TANK
512071
948438
PRE-WET MATS
BEFORE USING
511768
948366
HYDRAULIC OIL
SHELL TELLUS 32
CHECK LEVEL EVER 50 HOURS
PUSH
TO STOP
9486330
NAMEPLATE
TURN ON
WATER TANK
OUTLET VALVE
948484
CONTACT MULTIQUIP
SERVICE DEPT.
A
P/N 13118
PAGE 10 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — SPECIFICATIONS
TABLE 1. ENGINE SPECIFICATIONS
Yanmar L100AEDE/
L100EEDEVMK3 (EPA Approved)
Model
Honda GX340K1QAE
Robin EH34OYS0610
Air-cooled 4 stroke, overhead
valve, single cylinder, horizontal
shaft gasoline engine
Air-cooled 4 stroke, overhead
valve, single cylinder, horizontal
shaft gasoline engine
Single cylinder, vertical 4-cycle air-
cooled diesel
Type
Bore X
Stroke
3.2 in. X 2.50 in.
(88 x 64 mm)
3.31 in. X 2.40 in.
(84 x 61 mm)
3.39 in. X 2.76 in.
(86 x 70 mm)
Displacement
Max Output
20.60 cu. (337 cc)
11 H.P./3600 R.P.M.
20.63 cu. (338 cc)
11 H.P./3600 R.P.M.
24.78 cu. (406 cc)
10 H.P./3600 R.P.M.
Fuel Tank
Capacity
Approx. 1.59 U.S. Gallons (6 liters)
Unleaded Automobile Gasoline
1.1 liters (1.16 qt)
Approx. 1.6 U.S. Gallons (6 liters)
Unleaded Automobile Gasoline
1.2 liters (1.27 qt)
Approx. 1.65 U.S. Gallons (6.1 liters)
Diesel Fuel
Fuel
Lube Oil
Capacity
1.65 liters (1.74 qt)
Engine
Engine
Speed
2650 rpm 100
2650 rpm 100
2650 rpm 100
Full Load
Engine
Speed
Full Idle
1450 rpm 100
Dual Element
1450 rpm 100
Dual Element
1450 rpm 100
Dual Element
Air Cleaner
Engine
Lubrication
SAE 10W-30 (Oil Grade)
SG or SF (Service Class)
SAE 10W-30 (Oil Grade)
SG or SF (Service Class
SAE 10W-30 (Oil Grade)
SG or SF (Service Class
Speed
Control
Method
Centrifugal Fly-weight Type
Centrifugal Fly-weight Type
Centrifugal Fly-weight Type
Starting
Method
Recoil/Electric Start
Recoil/Electric Start
Recoil/Electric Start
15.0 X 17.7 X 17.4 mm
(380 X 450 X 443 mm)
15.83 X 17.91 X 10.09 mm
(402 X 455 X 485 mm)
16.42 X 18.50 X 19.45 mm
(417 X 470 X 494 mm)
Dimension (LXWXH)
Dry Net Weight
68.4 lbs (31 Kg.) Electric Start
82.8 lbs (33 Kg.) Electric Start
66.1 lbs (30 Kg.) Recoil Start
117 lbs (53 Kg.) Electric Start
106 lbs (48 Kg.) Recoil Start
TABLE 2. ROLLER SPECIFICATIONS
Impact Force 3,730 lbs. (1,692 kg)
Frequency
Gradeability
4,400 vpm
21 Percent
Drum Width
30 in. (76.2)
Overall Width
35.5 in. (90.1 )
Drive System
Hydrostatic
Travel Speed
0-2.5 mph (0-4 kph)
8.3 gal. (31.4 liters)
10 in (24.9 cm)
Water Tank Capacity
Compaction Depth of Dirt
Compaction Depth of Asphalt
Vibration Amplitude
Operating Weight (Empty)
Operating Weight (Empty)
4.0 (9.9 cm)
.019 in.
1,045 lbs. (474 kg.) Honda/Robin
1,065 lbs. (483 kg.) Yanmar
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — DIMENSIONS
Figure 1. V-30-4 Roller Dimensions Side View)
PAGE 12 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — DIMENSIONS
Figure 2. V304 Roller Dimensions (Front View)
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — ROLLER COMPONENTS
Figure 3. Roller Components 1
PAGE 14 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — ROLLER COMPONENTS
Figure 3 shows the location of the components and basic
components for the V304 compaction roller. The function of each
component or control is described below:
9. Fuel filler Port – Remove this cap to determine the
amount of fuel in the fuel tank. If low, add fuel through
this port.
10. Engine – This roller uses three different types of
engines, Honda GX-340, Robin EH-34 andYanmar L100
(Diesel). For additional engine information read the
engine Owner's Manual supplied with the roller.
1. Multi-Position Handle Bar – This bar can be set to
four different positions, park, high, middle and low.When
transporting the roller, always have the handle bar in
the upright (stow) position.
11. WaterTank Filler Port – Remove this cap to determine
the amount of water in the water tank. If low, add clean
water through this port.This water tank holds 8.3 gallons
(31.4 liters) of water.
2. ForwardTravel Lever –This is a variable speed control
lever. Squeeze this lever to make the roller travel in a
forward direction.
3. Emergency Stop Button – Press this button to stop
the roller in the event of an emergency. DO NOT use
this button as a means of stopping the roller under
normal conditions. When starting the engine make sure
that this push-button switch is in the up position.
12. Rear Stabilizer Roller – This roller aids the roller in
maintaining stability (prevents tipping) and simplifies
handling when maneuvering the roller.
13. Zerk Fittings – Lube and grease these fittings as
recommended in the maintenance section of this
manual.
4. ReverseTravel Lever – This is a variable speed control
lever. Squeeze this lever to make the roller travel in a
reverse direction.
14. Main Vibratory Roller – This roller is 30 inches wide
steel drum with beveled edges. The beveled help
prevent asphalt marring.
5. Vibration Control Lever – Move this lever to the ON
position an the eccentric will produce a vibration
frequency of 4,400 vpm (vibrations per minute). Move
the lever to the OFF position to stop the vibrations.
15. Front Stabilizer Roller – This roller aids the roller in
maintaining stability (prevents tipping) and simplifies
handing when maneuvering the roller.
6. Lifting Hook Eye – Attach a crane or lifting device to
this lifting hook eye. The lifting device should have a
lifting capacity of 1,000 lbs. (450 kg.)
16. Coco Mat/Scrapper Blade – This mat and blade helps
prevent the buildup of material between the drum and
frame. When using the roller for earth compaction DO
NOT let the mat come in contact with the roller drum. A
hook type latch is provide to keep the mat away from the
drum.
7. Handle Bar Release Pin – Remove this pin to position
the handle bar to the desired position. Make sure to
reinsert release pin and cotter pin after each new
position.
17. Sprinkler System/Water Shut-off Valve – A gravity
feed spray bar is provided for the wetting the roll for
asphalt pavement. Turn the water valve to the open
position to let water flow, return this valve to the closed
position when water is not required. In addition a water
filter has been provided to prevent foreign matter from
clogging the spray bar holes. Clean this filter as
referenced in the maintenance section of this manual.
8. Transport Hooks – These hooks are used in the
transportation of the roller (Figure 4).The hooks allow
the roller to hang over the tailgate of a dump truck.
Figure 4. Transport Hooks
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — ROLLER COMPONENTS
Figure 5. Roller Components 2
3. Travel Drive V-Belt – This belt is require to make the
roller travel in a forward or reverse direction. Check this
V-belt as outlined in the maintenance section of this
manual.
Figure 5 shows the location of additional components for the
V304 compaction roller. The function of each component or
control is described below:
1. Vibration Drive V-Belt – This belt is require to make
the roller vibrate. Check this V-belt as outlined in the
maintenance section of this manual.
4. Compartment Hood – Remove this hood to gain
access to the V-belts, hydrostatic pump, coupling
components, free wheel engagement lever etc.
5. Hydrostatic Pump – Provides hydraulic pressure to
2. Free Wheel Engagement Lever – Under normal
conditions this lever should be place in the forward
position (engaged). In the event the roller becomes
disable and must be moved (will not start), place the
lever in the side position (disengaged).
the drive system.
6. Hydrostatic Fluid Reservoir – Fill this reservoir with
hydrostatic transmission fluid. Fill with Mobil 300, GM
Dextron B or Ford MCZ-41A type transmission fluid.
This will allow the roller drum to rotate (free wheel).
IMPORTANT!, this lever is only to be used in cases
where the roller has be disabled. In normal operating
conditions this lever should be left in the engaged
position (forward)
7. Cogged- Drive Belt – This belt is used with the
hydraulic pump. Check this cogged drive belt as outlined
in the maintenance section of this manual.
PAGE 16 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — ENGINE COMPONENTS
Figure 6. Engine Controls and Components (HONDA)
INITIAL SERVICING
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
The engine (Figure 6) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
NOTE
WARNING
WARNING
Operating the engine without an air filter,
with a damaged air filter, or a filter in need of
replacement will allow dirt to enter the
engine, causing rapid engine wear.
Adding fuel to the tank should be accomplished only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel spill,
DO NOT attempt to start the engine until the fuel residue has been
completely wiped up, and the area surrounding the engine is dry.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
9. Muffler – Used to reduce noise and emissions.
WARNING
3. Engine ON/OFF Switch – ON position permits engine
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — GENERAL INFORMATION
The V304 Vibratory Roller is a walk-behind vibratory roller
specifically designed for the compaction and patching of asphalt
type surfaces.
SPRINKLER SYSTEM
A 8.3 gallon (31.4 liters) water tank with a gravity feed spray bar
is provided for wetting the roll for asphaltic pavement rolling.
The compaction force is delivered by a 30-inch wide steel drum
with beveled edges to help prevent asphalt marring. A fully
enclosed hydrostatic drive system offers a variable speed control
as well as smooth acceleration and braking
Before starting an asphalt rolling job, be sure all spray bar holes
are clear of dirt or foreign matter and are working. A coco mat is
provided to insure an even distribution of water.
DO NOT leave the coco mat in contact with the roll (drum) when
the roller is used for earth compaction. A hook is provided to hold
the mat away from the roll.The coco mats are intended to prevent
the build-up of material between the drum and the frame.
HYDROSTATIC DRIVE SYSTEM
This hydrostatic design offers a smooth performance, because
of a fully integrated hydrostatically actuated drive system, which
provides a variable speed control under varying load conditions.
Power from the hydraulic drive system is transferred via a drive
belt to a gear reducer.
Always use clean fresh water in the water tank.To prevent rust
and foreign debris from clogging the spray bar holes, drain and
flush water tank and spray bars every 30 days.
TRANSPORTATION
To help transport the roller from job site to job site, adjustable
transport hooks have been provided.These transport hooks allow
an operator to place the roller on the tailgate of a dump truck
without any assistance. The control handle of the V304 roller
can be folded vertically for ease of transport and storage.
CONTROLS
The forward-reverse control lever (located on the handle)
operates the hydrostatic pump which governs the roller speed
and direction of travel.The neutral position of this lever will cause
the roller to stop.The vibration control when actuated will apply
a force of 4,400 vpm (vibrations per minute).This vibratory feature
is controlled by an eccentric shaft via an operator controlled
mechanical clutch.
LIFTING THE ROLLER
When lifting of the roller is required (Figure 7), attach a suitable
hook or shackle to the lifting eye of the roller. Make sure the
lifting device is capable of lifting 1,045 lbs (450 kg).
FREEWHEEL ENGAGEMENT LEVER
The hydrostatic transmission is equipped with a free wheel
engagement lever, which, when actuated, allows the oil to circulate
freely within the roller, thereby permitting the roller to be moved
without the engine running.This lever is only to be used in the
event the roller is disabled.
.
This lever is located on the that side of the transmission which
faces the front of the roller. It is actuated by placing the handle
into the side-lock position.To gain access to this lever raise the
roller's hood. DO NOT raise hood while engine is running, STOP
engine.
NOTE
In normal operating conditions the roller
will not move in a forward or reverse
direction unless the free wheel
engagement lever is in the engage position
(forward).
Figure 7. LiftingThe Roller
PAGE 18 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — GENERAL INFORMATION
Tipping (Rollovers)
CAUTION :
CAUTION :
CAUTION :
NEVER! operate the roller on side slopes (Figure 9). The
possibility exist that the roller could tip over (roll over), thus
causing bodily harm even death and serious damage to the
equipment.
NEVER! stand under, or get onto the roller
while it is being lifted or moved.
ONLY! use steel ropes or chains that are
capable of lifting at least 1,045 lbs (450 kg).
NEVER! use any other part of the roller for
lifting purposes. Use the lifting eye. Using other
parts of the roller for lifting will cause severe
damage to the roller,
Figure 9. Tipping (Rollover)
In the event the roller does tip over, extreme care must be taken
to prevent damage to the engine. When the roller has been
tipped over, oil from the engine crankcase can flow into the
combustion chamber, which can severely damage the engine
the next time it is started.
OPERATING ON SLOPES
Special care must be taken when operating the roller on hills or
slopes. There exist the possibility of serious injury to the operator
and severe damage to the roller in the event of a roll over.
ALWAYS operate the roller up and down hills rater than from
side to side. For safe operation hillside slopes should not exceed
12 degree (21 % grade). See Figure 8 below.
IMMEDIATELY after a unit has tipped over upright the unit as
soon as possible to prevent oil from leaking into the combustion
chamber.
CAUTION :
To prevent damage to the engine after a
rollover, the unit must NOT be started.NEVER
start a unit after a rollover. CONTACT your
nearest authorized multiquip dealer for
instructions or servicing.
NOTE
NEVER! operate the roller on side slopes.
The roller may tip over causing injury to
personnel and severe damage to the
equipment
Figure 8. Recommend Slope
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — INSPECTION
Before Starting
1. Read safety instructions at the beginning of manual.
2. CleantheROLLER,removingdirtanddust,particularlythe
engine cooling air inlet, carburetor and air cleaner.
3. Check theairfilterfor dirtanddust. Ifairfilterisdirty,replace
air filter with a new one as required.
Figure 11. Engine Oil Dipstick (Oil Level)
NOTE
4. Check carburetor for external dirt and dust. Clean with dry
compressedair.
5. Checkfasteningnutsandboltsfortightness.
Some engines used with the V304 Roller
have an oil Alert System.This system will
automatically stop the in the event of low
oil level. ALWAYS be sure to check the
engine oil level prior to starting the engine.
Engine Oil Check
1. To check the engine oil level, place the saw on secure level
ground with the engine stopped, and the diamond blade
removed.
2. Remove the filler cap/dipstick from the engine oil filler hole
(Figure 10) and wipe it clean.
Table 3. Oil Type
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
0°C or Lower
Figure 10. Engine Oil Dipstick (Removal)
Fuel
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
CAUTION :
4. Iftheoillevelislow(Figure11), filltotheedgeoftheoilfiller
holewiththerecommendedoiltype(Table3).Maximum oil
capacity is 400 cc.
NEVER fill the fuel tank (Figure 12) while
the engine is running or in the dark. Fuel
spillage on a hot engine can cause a fire
or explosion. If fuel spillage occurs, wipe
up the spilled fuel completely to prevent
fire hazards.
NOTE
Reference manufacturer engine manual for
specific servicing instructions.
DO NOT smoke while refueling, motor
fuels are highly flammable and can be
dangerous if mishandled.
PAGE 20 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — INSPECTION
Water Tank
Explosive Fuel
1. Fill the water tank (Figure 13) with clean water, and verify
that valve for the water tank is closed.
Gasoline Check
1. Remove the gasoline cap located on top of fuel tank.
2. Handle Fuel in a safety container.If the container does not
have a spout use a funnel.
3. Visually inspect to see if fuel level is low. If fuel is low,
replenishwithunleadedfuel.Whenrefueling,besuretouse
a strainer for filtration. DO NOT top-off fuel. Wipe up any
spilled fuel.
4. Pay attention to the fuel tank capacity when replenishing
fuel. Refer to the fuel tank capacity listed on page 11,
Engine Specification Table 1.
Figure 13.WaterTank Filler Port
Hydraulic Pump Fluid
1. Visuallyinspectthehydraulicfluidinthehydraulicreservoir
(Figure14). Ifthehydraulicfluidislow, fillthereservoir with
Mobil 300, GM Dextron B or Ford MZC-41A type hydraulic
transmission fluid to the correct level.The correct hydraulic
fluid level will be indicated on the reservoir.
Figure 12. FuelTank Filler Port
Figure 14. Hydraulic Reservoir Filler Port
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — INSPECTION
Gearbox Lubrication
Vibratory andTravel V-BeltTension
Check the tension of the vibratory and travel V-belts
(Figure 16). This tension can be checked by the amount
of deflection when the belt is pressed midway between
the two pulleys. The deflection of the travel belt should
be approximately 3/4 of an inch (2 cm.), the vibratory V-
belt should have a deflection of approximately 2 to 2-1/2
inches (5 to 6 cm.)
1. Remove the oil fill drain plug on the gearbox (Figure 15). If
the oil level is correct oil will begin to leak out. Retighten
drain plug.
2. If the level of the oil in the gearbox is low, no oil will leak out
whenthedrainplugisremoved. Addgearboxoil,typeSAE
90throughthisdrainopening. Filluntiloilbeginstoleakout
from the drain opening cavity.If gearbox oil is low no oil will
leak out when drain plug is removed. Retighten drain plug.
Clogged Drive BeltTension
Check the tension of the cloggedV-belt (hydrostatic pump).This
tension can be checked by the amount of deflection when
the belt is pressed midway between the two pulleys. The
deflection of the travel belt should be approximately 1/2
of an inch (1.27 cm.).
Figure 16.Vibratory,Travel and Pump Belts
Figure 15. Gearbox Fill and Drain Plug
PAGE 22 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — INITIAL START-UP
Initial Start-up Instructions
Handle Bar Adjustment
Adjustment of the handle bar is made by removing the
handle bar hitch pin, then pulling the release pin. Once
released pin has been removed, position handle bar to
desired height (Figures 17 and 18), then insert release
pin and lock with cotter pin.
Figure 18. Handle Positions 2
Starting
CAUTION:
DO NOT attempt to operate the roller until the
Safety, General Information and Inspection
sections have been read and understood.
Depending on the type of engine installed on
roller, operating steps may vary somewhat.See
engine manufactures operating manual. The
following start-up procedure makes reference
to a HONDA engine.
1. ALWAYSmakesurethattheemer-
gency stop button (Figure 19) is
pulled all the way out (disengage).
Figure 19. Emergency Stop Button
2. Place the engine fuel valve lever (Figure 20) to the "ON"
position.
Figure 17. Handle Positions 1
Figure 20. Engine FuelValve Lever
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — INITIAL START-UP
3. Place the Engine ON/OFF switch (Figure 21) in the "ON"
position.
Figure 23.Throttle Lever
6. Place the Engine ON/OFF switch (Figure 24) to the
Figure 21. Engine Ignition Switch (0n Position)
NOTE
"START" position. Hold until engine starts.
The CLOSED position of the choke lever enriches
the fuel mixture for starting a COLD engine.The
OPEN position provides the correct fuel mixture
for normal operation after starting, and for
restarting a warm engine.
4. Place the Choke Lever (Figure 22) in the "OPEN" position
Figure 24. Engine Ignition Switch (Start Position)
NOTE
DO NOT keep the ignition switch in the START
position for more than 5 seconds.
7. If the engine has started allow switch to return to ON
position, then slowly return the choke lever (Figure 22)
to the CLOSED position. If the engine has not started
repeat steps 1 through 5.
Figure 22. Choke Lever
5. Place the throttle lever (Figure 23) halfway between fast
and slow for starting. All sawing is done at full throttle. The
engine governor speed is factory set to ensure optimum
blade operating speeds.
8. Before the roller is placed into operation, run the engine
for several minutes. Check for fuel leaks, and noises that
would associate with a loose guard and/or covers.
9. All rolling is done at full throttle. Your engine governor has
been set at the factory to ensure an optimum speed
setting.
PAGE 24 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — OPERATION
Operation
CAUTION :
NEVER perform service or maintenance
on the roller when the engine is running.
The engines used with this roller DO NOT
require a pre-mix of oil and gasoline.
Free Wheel Engagement Lever
Before the roller can be put into operation, check and make sure
that the free wheel engagement lever (Figure 25) is in the
engagement position (forward). Lift the compartment hood to
gain access to this lever.
Figure 27. Forward and Reverse Control Levers
Neutral Position
1. Squeezing the left control lever (Figure 28) will cause the
roller to move in a forward direction. Squeezing the lever
all the way towards the operator will achieve maximum
speed. Use a smooth squeezing action on the drive control
levertopreventabrupttakeoffs.
Figure 28. Forward Control Lever
Figure 25. Free Wheel Engagement Lever
Water Shut-offValve
2. Squeezingthe rightcontrollever(Figure29)willcausethe
rollertomoveinareversedirection.Useasmoothsqueez-
ingactiononthedrivecontrollevertopreventabrupttake-offs.
If the water sprinkler is going to be used for a roll of asphalt
paving, fill the water tank with clean water and turn the water
valve to the OPEN position (Figure 26).
Figure 26.Water Shut-OffValve
Directional Speed Control Levers
1. Withtheenginerunning,bothdirectionalandspeedcontrol
levers (Figure 27) should be in their neutral positions.
Figure 29. Reverse Control Lever
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — OPERATION
2. Place the water valve in the CLOSED position (if used).
Vibratory Control
3. Place the engine throttle lever (Figure 23) in the slow
1. For vibratory action, with the engine running (full speed)
place the vibratory control lever ( Figure 30) to the ON
position.Therollerwillnowproduceavibratoryfrequencyof
4,400vps.
position, and let the engine idle for 3-5 minutes.
4. PlacetheEngineON/OFFswitch(Figure32) in the"OFF"
position and remove the key. Place the key in a save place.
CAUTION :
NEVER! engage vibrator on concrete or
asphalt type surfaces.
Figure 32. Engine Ignition Switch (OFF Position)
Figure 30.Vibratory Control Lever (ON)
Shut-Down
4. Place the engine fuel valve lever (Figure 20) in the OFF
position.
1. Place the vibration control lever (Figure 31) on the roller to
5. Clean the entire roller with warm water and mild soap. Pay
close attention to the scrapper bar and spray bar holes,
makingsurethatnodirtordebrisispresent. Dirtanddebris
can cause the sprinkler system to get clogged.
the OFF position (vibration stops).
Figure 31.Vibratory Control Lever (OFF)
PAGE 26 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — MAINTENANCE
Maintenance
Scrapper Blades (Daily)
Vibrating Shaft Bearings (50 hrs)
The scrappers blades should be cleaned daily after each use to
prevent the build-up of dirt, mud, tar and any other foreign matter
associated with pavement rolling. Use a high pressure water jet
(500-1000 psi) and a strong brush to clean the scrapper blades.
The double row of self-aligning ball bearings on the vibrator
shaft are special bearings that are not available at the local
bearing supply houses. Lubrication of these bearings is very
important and should be lubricated after each 50 hours of
operation. Rotate roller drum so that grease fittings are towards
the lower front.
V-30-4 Roller (Daily)
Clean the roller daily after each use. If using a pressurized hose
keep the pressure between 500 and 1000 psi. Avoid using harsh
chemicals, mild detergent soap will do. Avoid direct high water
pressure to the engine, hoses and decals.
If it becomes necessary to tear down and reassemble the roller,
remove wash out and repack bearing housing with specified
grease. After cleaning and checking bearings, they should be
lightly packed with the specified grease.
Water Tank (30 Days)
Drain and flush the water tank and spray bars every 30 days.
When refilling the water tank, use only clean water.
It is essential that no end thrust be applied to these bearings. On
reassembly there should be approximately .060" (min) to .120"
(max) end float on the vibrator shaft, which may reduce when the
shaft reaches working temperature.The bearings must be a light
slip fit on the shaft to insure axial freedom.
Adjusting or ChangingTravel V-Belt
1. Un-lock the hood retaining latch and lift the hood to gain
accesstotheV-belts. Toadjustthetravel V-belt,loosenthe
fourmountingscrewsonthereductiongearbox(Figure33)
HydrostaticTransmission Fluid (50 hrs)
Inspect the fluid level in the hydraulic fluid reservoir every 50
hours of operation, if low, fill with Mobil 300, GM Dextron B or
Ford MZC-41A type hydraulic transmission fluid. Change
hydraulic transmission fluid on a yearly basis.
Vibrator Clutch Assembly (100 hrs)
The clutch must be greased every 100 hours of operation. Stop
the engine with clutch engaged to check V-belt tension. See
"ensioning g theV-belts"
Engine andVibratory Shaft Speed Check (100 hrs)
To check the engine and vibratory shaft speed the use of an
"Vibra-Tak" tool will be required.
To check engine speed, place the bottom of the Vibra-Tak tool
(knurled cap) on the engine shroud. Move sliding sleeve to a
position where the maximum throw of wire reed is obtained.
Take a reading from edge of sleeve and multiply reading by
1000.The result is the RPM's the engine is running at.
If the engine RPM speed is too fast or slow, consult the engine
owner's manual on how to adjust the engine speed.
To check the vibrations per minute (vpm) of the roller shaft, place
the bottom of theVibra-Tak tool (knurled cap) on the roller drum
while the vibrating clutch is engaged. Adjust and read tool as
mentioned above.The vibratory shaft speed should be 4400
vpm.
Figure 33.Travel and Vibratory V-Belts
2. Usetheprypoint(Figure33)toachievecorrectamountofV-
belttension.Tightengearboxscrews,andcheckbelttension
byverifyingtheamountofdeflectionwhenthebeltispressed
midway between the two pulleys.This deflection should be
approximately 3/4 of an inch (2 cm.)
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — MAINTENANCE
Adjusting Control Rods
Adjusting or Changing VibratoryV-Belt
Travel Control Rod
1. To adjust the vibratoryV-belt, loosen the pulley tensioner
nut (Figure 33) and adjust theV-belt for approximately 2
to 2-1/2 inches (5 to 6 cm.) of deflection. Check V-belt
deflection when V-belt is pressed midway between the
two pulleys. When the correct amount V-belt deflection
has been achieved, retighten pulley tensioner nut.
1. To adjust the travel control rod (controls forward, reverse
andneutral)itwillbenecessarytostarttheengineandrun
it a low speed.
2. On the travel control rod, loosen the counter nut on the
rod end . Remove retaining screw as shown in Figure
35, then rotate the rod end to acquire desired length.
Adjusttravelrodsothatitsstaticposition(noforceapplied
on drive control) falls into the neutral position.The roller
should not move once adjustment is complete. Retighten
all hardware.
2. IMPORTANT! always adjust the vibratoryV-belt to the rec-
ommendedbelttension.AtightV-beltwillcausetherollerto
vibrate even it the vibration control lever is in the OFF
position. Remember a looseV-belt will decrease the vibra-
tory action or there may not be any vibratory action at all.
Adjusting or Changing Hydrostatic Pump Drive Belt
1. To change or adjust the clogged drive belt (Figure 34) for
thehydrostaticpump,loosenthefourmountingboltsonthe
hydrostaticpump.Movethepumpunittowardstherearofthe
rollerandadjustthecloggedbeltforapproximately1/2inch
(1.27 cm) deflection when the belt is pressed midway
between the two pulleys. When the correct amount of belt
deflectionhasbeenachieved, retightenhydrostaticpump
mounting screws.
Figure 35.Travel and Vibratory V-Belts
Vibratory Control Rod
1. To adjust the vibratory control rod (controls vibration),
loosen the counter nut (Figure 3) on the rod end of the
vibratory control rod. Remove the retaining screw on
the rod end and rotate the rod to achieve the desired
rod length.
Figure 34. Hydrostatic Pump Drive Belt
NOTE
2. Continue adjusting, until clutch operation is adequate.
The V-belt for the vibratory action should not move
when the control lever is in the OFF position. Once
adjustment is complete, retighten all hardware.
Use caution when adjusting control rods, since
engine is running.
PAGE 28 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — MAINTENANCE
Clutch and Engine coupling Lubrication
Lubricate the clutch and engine coupling as shown in Figure 36.
ZERK
FITTING
LUBRICATE ENGINE
COUPLING WITH
EP-3 GREASE .33 OZ.
ZERK
FITTING
LUBRICATE CLUTCH WITH
EP-3 GREASE .33 OZ.
Figure 36. Clutch and Engine Coupling
Lubrication Points (Zerk Fittings)
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — PREPARATION FOR LONG -TERM STORAGE
Roller Storage
For storage of the roller for over 30 days, the following is
recommended:
Drain the fuel tank completely.
Run the engine until the fuel in the injection system is
completely consumed.
Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.
Drain water tank
Clean the entire roller and engine compartment.
Remove battery and store it in cool dry place.
Place roller control handle in the upright position
(vertical).
Cover the roller and place it a clean dry area, that is
protected from harsh elements.
Remove ignition key, and store in a safe place.
PAGE 30 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — TROUBLESHOOTING (ROLLER)
TABLE 4. ROLLER TROUBLESHOOTING
POSSIBLE PROBLEM
Low engine RPM?
SYMPTOM
SOLUTION
Adjust to 2650 RPM.
V-belt slipping?
Adjust tension or replace.
Adjust linkage.
Low Vibration
Clutch rod linkage out of
adjustment?
Low engine speed?
Low transmission oil?
Low transmission fluid?
Check cooling fan?
Linkage out of Adjustment?
Defective clutch?
Adjust to 2650, inspect linkage.
Fill to proper level.
Fill to proper level.
Replace.
Loss of Power
System Operation Hot
Operates Slow in One Direction
No Vibration
Adjust linkage.
Replace clutch.
V-belt tension?
Adjust or replace.
Main eccentric bearings?
Lubrication problem?
Inspect vibratory shaft floatation.
Lubricate bearing.
Engine Stalls when Vibration
Lever is Engaged
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — TROUBLESHOOTING (ENGINE)
TABLE 5. ENGINE TROUBLESHOOTING
SYMPTON
POSSIBLE PROBLEM
SOLUTION
Speed control lever is in "STOP" position?
STOP solenoid is in the "STOP" position?
Set speed control lever to "START" position.
Set stop solenoid to the "START" position.
Adjust and lubricate if necessary.
No Fuel reaching injection pump?
Defective fuel pump?
Add fuel. Check entire fuel system.
Replace fuel pump.
Fuel filter clogged?
Replace fuel filter and clean tank.
Replace or repair fuel line.
Engine will not start or start is
delayed, although engine can
be turned over.
Faulty fuel supply line?
Check piston, cylinder and valves. Adjust or
repair per engine repair manual.
Compression too low?
Repair or replace injector in accordance with
engine repair manual.
Fuel injector not working correctly?
Oil pressure too low?
Check engine oil pressure.
Comply with cold starting instructions and
proper oil viscosity.
Low starting temperature limit exceeded
Defective battery?
Charge or replace battery.
Check whether clear (not turbid) fuel emerges
from the fuel line (detach from injection
pump). If the fuel is turbid or seperated either,
warm up the engine or drain the complete fuel
supply system. Refuel with winter grade diesel
fuel.
Fuel seperates has inadequate resistance to
low temperatures?
At low temperatures engine will
not start.
Refill engine crankcase with correct type of oil
for winter environment.
Engine oil too thick?
Defective battery?
Replace battery.
Throttle lever in STOP position?
Fuel filter blocked?
Reposition throttle lever to RUN position.
Replace fuel filter.
Engine fires but stops soon as
starter is switched off.
Fuel supply blocked?
Electrical problem at fuel solenoid?
Fuel tank empty?
Check the entire fuel system.
Repair using #7 wire.
Add fuel.
Fuel filter blocked?
Replace fuel filter.
Engine stops by itself during
normal operation.
Defective fuel pump?
Replace fuel pump.
Mechanical oil pressure shutdown sensor
stops the engine due to low oil?
Add oil. Replace low oil shutdown sensor if
necessary.
PAGE 32 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — TROUBLESHOOTING (ENGINE)
TABLE 5. ENGINE TROUBLESHOOTING (CONTINUED)
POSSIBLE PROBLEM
Fuel tank empty?
SYMPTON
SOLUTION
Replace fuel filter.
Replace fuel filter.
Fuel filter clogged?
Fuel tank venting is inadequate?
Leaks at pipe unions?
Ensure that tank is adequately vented.
Low engine power, output and
speed.
Check threaded pipe unions tape and tighten
unions a required.
Speed control lever does not remain in selected See engine manual for corrective action.
position?
Engine oil level too full?
Air filter blocked?
Correct engine oil level?
Clean or replace air filter.
Adjust valves per engine specification.
See engine manual.
Low engine power output and
low speed, black exhaust
smoke.
Incorrect valve clearances?
Malfunction at injector?
Drain off engine oil down to uppermark on
dipstick.
Too much oil in engine crankcase?
Air-cooled diesel engine runs
very "HOT". Cylinder head
overheat, telltale lamp comes
on (option)
Clean cooling air system, remove shrouds and
cooling fin areas.
Entire cooling air system contaminated blocked?
Check that air guide plates and enclosure
elements are all present and make a tight
seal.
Inadequate sealing at air guide plates or
capsule elements?
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
SAMPLE PARTS LIST
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
WASHER, 3/8 IN....1 .....MQ-45T ONLY
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
NO. Column
Indicated by:
Unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“Not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
PAGE 34 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — SUGGESTED SPARE PARTS
V304 1 TO 3 UNITS WITH HONDA GX340K1QAE,
ROBIN EH-34OYSO610 AND YANMAR L100ADDE
ENGINES.
1 to 3 Units
Qty.
P/N
Description
12 .......... EM906131 ....... BUSHING
12 .......... EM906132 ....... WASHER
3 ............ EM505284 ....... COCOA MAT
3 ............ EM491116 ....... V-BELT TRAVEL
3 ............ EM504233 ....... V-BELT VIBRATORY
3 ............ EM491132 ....... COGGED DRIVE BELT (PUMP)
15 .......... EM504441 ....... MOUNT, SHOCK
3 ............ 491010 ............. RUBBER LATCH
3 ............ 9807955846 ..... SPARK PLUG (HONDA)
3 ............ 17210ZE3505 .. ELEMENT AIR CLEANER (HONDA)
1 ............ EM502133 ....... CLUTCH ASSY.
1 ............ EM106395 ....... WATERTANK EXPANSION PLUG
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — NAME PLATE AND DECALS
NAME PLATE AND DECALS
5
4
6
3
7
8
2
15
14
9
1
12
10
13
11
PAGE 36 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO
1
PART NO
PART NAME
QTY.
1
REMARKS
EM948484
EM948501
EM512071
EM511767
EM9486330
EM511766
EM511769
DECAL : WATER VALVE
DECAL : SAFETY INSTRUCTIONS
DECAL : VIBRATION ON/OFF
DECAL : REVERSE
DECAL : PUSH TO STOP
DECAL : FORWARD
DECAL : SAFETY CHAIN
DECAL : NAME PLATE .................................... 1 .......... CONTACT MQ SERVICE DEPT.
....................................................................................... W/MODEL & S/N
DECAL : WATER TANK
DECAL : MQ LONG
DECAL: COCO MAT
2
1
3
1
4
1
5
1
6
1
7
1
8
9
EM948438
EM511782
EM948044
13118
EM948366
EM511768
35137
1
1
1
1
1
1
10
11
12
13
14
15
DECAL: POWDER COATED
DECAL: PRE-WET MATS
DECAL: HYDRAULIC OIL
DECAL: CAUTION READ MANUAL ................ 1
SEE DECAL ILLUSTRATIONS ON PAGE 10
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — COCOA MAT ASSY.
COCOA MAT ASSY.
28
2
NEW STYLE
ROLLER SUPPORT
27
32
5
1
31
29
35
2
10
30
3
24
30
4
34
32
3
2
33
1
36
10
1
9
1
31
25
10
1
8
25
7
3
1
3
2
24
6
1
11
OLD STYLE
ROLLER
SUPPORT
7
2
1
18
8
9
1
1
19
26
1
17
16
15
23
19
23
18
24
1
14
12
13
23
21
17
20
16
25
10
5
9
22
1
8
1
NOTES
7
25
OLD STYLE ROLLER
SUPPORT. S/N 295200
AND BELOW.
1
6
1
NEW STYLE ROLLER
SUPPORT. S/N 295201
AND ABOVE.
24
9
2
1
OLD STYLE
ROLLER
SUPPORT
7
1
8
PAGE 38 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — COCOA MAT ASSY.
COCOA MAT ASSY.
NO
1
2
3
4
5
6
7
8
PART NO
EM505543
EM923348
EM969023
EM505146
EM505542
EM505454
EM906132
EM906131
EM969023
EM503982
EM505284
EM505138
EM492358
EM923057
EM969049
EM963003
EM923057
EM969005
EM963610
EM969013
EM505140
EM505582
3019092
PART NAME
QTY.
REMARKS
ARM, RH STABILIZER ROLLER ............... 2 ............... S/N 251200 AND BELOW
WASHER, LOCK 5/8
NUT, 5/8 - 11
PLATE, FRONT SCRAPER
ARM, LH STABILIZER ROLLER ............... 2 ............... S/N 251200 AND BELOW
ROLLER, STABILIZER .............................. 2 ............... S/N 251200 AND BELOW
BUSHING, ROLLER .................................. 4 ............... S/N 251200 AND BELOW
WASHER, BUSHING................................. 4 ............... S/N 251200 AND BELOW
NUT, NYLOC 5/8 - 11 ................................ 4 ............... S/N 251200 AND BELOW
SCREW, HHC 5/8 - 11 X 2
MAT, COCOA
FRAME, COCOA MAT
SCREW, HHC 1/4 - 20 X 1-1/4
WASHER, FLAT 1/4
NUT, NYLOC 1/4 - 20
SCREW, HHC 1/4 - 20 X 3/4
WASHER, FLAT 1/4
NUT, NYLOC 1/4 - 20
SCREW, HHC 3/8 - 16 X 1
NUT, NYLOC 3/8 - 16
BRACKET
PLATE, REAR SCRAPER
WASHER, FLAT 3/8
4
4
1
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
4
1
1
1
1
1
12
12
12
4
4
2
1
4
4
4
EM963692
492584
SCREW, HHC 1/2 - 13 X 1-1/2
NUT, NYLOC 1/2 - 13
CHAIN, COCOA MAT
EM505375
EM516754
EM516753
EM516312
EM492173
EM506109
EM492586
EM492313
EM292624
EM492554
EM491704
1
ARM, RH STABILIZER ROLLER ............... 2 ............... S/N 251201 AND ABOVE
ARM, LH STABILIZER ROLLER ............... 2 ............... S/N 251201 AND ABOVE
ROLLER, STABILIZER .............................. 2 ............... S/N 251201 AND ABOVE
FLANGE BEARING ................................... 4 ............... S/N 251201 AND ABOVE
WASHER, FLAT 5/8" ................................. 4 ............... S/N 251201 AND ABOVE
NUT 5/8" NC NYLOCK .............................. 4 ............... S/N 251201 AND ABOVE
BOLT HHCS 3/8" NC X 1-1/2 G5 ............... 8 ............... S/N 251201 AND ABOVE
WASHER ................................................... 8 ............... S/N 251201 AND ABOVE
NUT 3/8" NYLOCK .................................... 8 ............... S/N 251201 AND ABOVE
GREASE ZERK FITTING ......................... 4 ............... S/N 251201 AND ABOVE
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — TRAVEL LINKAGE ASSY.
TRAVEL LINKAGE ASSY.
13
17
18
16
4
16
22
21
19
20
9
9
23
10
16
24
25
26
28
13
12
4
9
15
5
14
11
29
1
31
27
28
11
5
7
9
12
5
4
2
8
10
7
3
NOTES:
INCLUDED WITH PUMP
2
1
OVERRIDE LEVER, ITEM 25.
30
7
6
1
PAGE 40 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — TRAVEL LINKAGE ASSY.
TRAVEL LINKAGE ASSY.
NO
1
PART NO
EM963057
504564
PART NAME
QTY.
1
2
1
3
2
1
3
1
4
2
2
1
2
1
1
3
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
REMARKS
SCREW, HHC 3/8 - 16 X 1-1/2
GRIP, HANDLE
2
3
503736
SPACER
4
EM959080
EM969013
492378
ROD END, 3/8 - 24 - R/HAND
NUT, NYLOC 3/8 - 16
SCREW, HHC 3/8 - 16 X 1-3/4
SPACER
5
6
7
503736
8
EM503738
EM490172
3019092
EM503744
EM511911
963610
BEARING
9
NUT, HEX 3/8 - 24
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
WASHER, FLAT 3/8
SPRING, LOWER DRIVE CONTROL
ROD, DRIVE CONTROL
SCREW, HHC 3/8 - 16 X 1-1/4
BELL CRANK, DRIVE CONTROL
NUT, NYLOC 1/2 - 13
BUSHING, OUTER BELL CRANK
SCREW, HHC 1/2 - 13 X 4-1/2
KEY, COTTER 1/16 X 1/2
PIN, CLEVIS
EM511883
492584
EM511869
503111
EM509157
EM511898
EM511875
EM511913
EM511909
0166 A
EM969012
EM511890
EM492365
EM923023
492582
CLEVIS, DRIVE CONTROL
ROD, HYD. PUMP CONTROL
LEVER, PUMP CONTROL
WASHER, LOCK 3/8
NUT
LEVER, PUMP OVERRIDE
SCREW, HHC 5/16 - 18 - 1
WASHER, FLAT 5/16"
NUT, NYLOC 5/16-18
SCREW, HHC 5/16 - 18 X 1-1/4
HANDLE CONTROL
CLEVIS
EM492365
EM511905
511891
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — VIBRATORY LINKAGE ASSY.
VIBRATORY LINKAGE ASSY.
15
PART OF
CHASSIS
14
9
16
4
21
4
14
19
11
4
23
18
18
13
12
10
12
4
19
5
21
17
20
24
1
14
4
17
6
5
3
4
8
22
2
7
1
PAGE 42 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — VIBRATORY LINKAGE ASSY.
VIBRATORY LINKAGE ASSY.
NO
1
PART NO
EM969013
EM492358
EM505279
EM490172
EM511912
491019
EM963059
EM969079
EM511886
EM511898
EM509157
EM511884
EM511875
EM959080
EM963610
EM511914
492364
PART NAME
QTY.
2
REMARKS
NUT, NYLOC 3/8 - 16
2
SCREW, HHC 1/4 - 20 X 1-1/4
LEVER, VIBRATORY CONTROL
NUT, HEX 3/8 - 24
1
3
1
4
4
5
ROD VIBRATORY CONTROL
KNOB
1
6
1
7
SCREW, HHC 3/8 - 16 X 2
NUT, NYLOC 1/4- 20
1
8
1
9
BELL CRANK, CLUTCH
PIN, CLEVIS
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
KEY, COTTER 1/16 X 1/2
BELL CRANK, CLUTCH CONTROL
CLEVIS, LOWER VIBRATORY CONTROL
ROD-END, 3/8 - 24 R/HAND
SCREW, HHC 3/8 - 16 X 1-1/4"
ROD, NO.1 CLUTCH
1
1
1
2
3
1
SCREW, HHC 5/16 - 18 X 1"
FORK, CLUTCH
4
EM502643
EM923023
EM512067
442582
EM511874
3019092
EM511915
2
WASHER, FLAT 5/16"
3
CLEVIS, CLUTCH
1
NUT, NYLOC 5/16 - 18
CLEVIS, UPPER VIBRATORY CONTROL
WASHER, FLAT 3/8"
1
1
1
ROD, NO. 2 CLUTCH
1
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — HANDLE ASSY.
HANDLE ASSY.
PAGE 44 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — HANDLE ASSY.
HANDLE ASSY.
NO
1
PART NO
EM505307
EM505398
EM505310
EM503115
3103160
EM511907
EM744
PART NAME
QTY.
REMARKS
CABLE ASSY. (ENGINE)
SWITCH, KILL
1
1
1
1
1
1
1
1
2
2
2
3
CABLE ASSY. (KILL SWITCH)
SCREW
WASHER, LOCK 3/16"
HANDLE BAR
CLEVIS PIN 1/2" X 4"
HAIR PIN 5/8" X 3/4"
SCREW, HHC 1/2 - 13 X 1-1/4
NUT, NYLOC 1/2 - 13
4
5
6
7
8
EM745
9
EM963102
492584
10
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — CHASSIS ASSY.
CHASSIS ASSY.
PAGE 46 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — CHASSIS ASSY.
CHASSIS ASSY.
NO
1
PART NO
491010
490202
503723
EM503978
5117
PART NAME
QTY.
REMARKS
LATCH KIT, ENG HSG (RUBBER) ................ 1 .................. INCLUDES ITEMS W/
*
2
RUBBER PROTECTOR
RIVET
1
2
1
1
1
3
4
RIVET
5
COTTER PIN, 1/16 X 1/2
CLEVIS PIN, 1/4 X 1-1/2 PLATED
*
*
6
8167
*
7
SHROUD FASTENER ................................... 1 .................. SUPPLIED IN KIT ONLY
8
EM504050
EM969079
492355
COVER, PUMP AND CONTROLS
NUT, NYLOC 1/4 -20
1
18
18
3
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
SCREW, HHC 1/4 20 X 1/2
HINGE, COVER
EM503740
EM504051
EM923023
EM923343
492363
COVER, BELT
1
WASHER, FLAT 5/16"
WASHER, LOCK 5/16
SCREW, HHC 5/16 - 18 X 3/4
PLATE, ENGINE BASE
WASHER, FLAT 3/8
4
4
5
EM510091
3019092
1
4
EM963057
0166A
SCREW, HHC 3/8 - 16 X 1-1/2
WASHER, LOCK 3/8
SCREW, ALLEN 3/8 - 16 X 3/4
NUT, NYLOC 5/16 - 18
BASE SWITCH
FLAT WASHER.............................................. 1 .................. SUPPLIED IN KIT ONLY
BRACKET, LATCH HOLDER ........................ 1 .................. SUPPLIED IN KIT ONLY
WATER TANK EXPANSION PLUG
FRAME
4
4
EM492263
492582
4
1
EM505652
1
*
24
25
26
*
EM106395
EM505641
1
1
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — TRANSPORT HOOKS ASSY.
TRANSPORT HOOKS ASSY.
PAGE 48 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — TRANSPORT HOOKS ASSY.
TRANSPORT HOOKS ASSY.
NO
1
PART NO
EM492421
EM502677
EM968446
EM505396
EM511866
EM969023
EM923350
EM492406
PART NAME
QTY.
REMARKS
SCREW, HHC 3/4 - 10 X 3-1/2
HOOK, HANGER
6
2
6
1
1
2
6
1
2
3
NUT, HEX 3/4 - 10
CARRYING, HANGER
BRACKET, STRUT
NUT, NYLOC 5/8 - 11
WASHER, LOCK 3/4
SCREW, HHC 5/8 - 11 X 1-1/2
4
5
6
7
8
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — PUMP DRIVE ASSY.
PUMP DRIVE ASSY.
14
15
17
13
10
11
12
16
9
22
7
18
19
5
9
8
3
6
4
20
1
2
6
8
21
NOTES:
INCLUDED WITH HYDROSTATIC
3
1
PUMP, ITEM 20.
PAGE 50 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — PUMP DRIVE ASSY.
PUMP DRIVE ASSY.
NO
1
PART NO
492622
PART NAME
QTY.
1
REMARKS
WASHER, LOCK 1/4
SCREW, HHC 1/4 - 20 X 3/4
SCREW, HHC 3/8 - 16 X 3-1/2
WASHER, FLAT PULLEY
PULLEY, TRAVEL
2
EM963003
EM490166
EM491086
EM490300
EM491759
TBD
1
3
4
4
1
5
1
6
KEY, WOODRUFF 1/8 X 1/2
SCREW
WASHER, 3/8
NUT, NYLOC 3/8 - 16
HYDRAULIC RESERVOIR/CAP
BELT, ENGINE TO PUMP DRIVE
SCREW, SET 1/4 - 20 X 1/4
FAN
2
7
1
8
EM504679
492583
4
9
4
10
1
*
11
12
13
14
15
16
17
18
19
20
21
22
EM491132
EM503110
EM493150
492369
1
1
1
SCREW, HHC 1/4 - 20 X 1-1/2
WASHER, LOCK 1/4
SCREW, HHC 3/16- 24 X 3/4
WASHER, LOCK 3/16
SPACER, FAN
1
2101402
1
EM503115
3103160
2
2
502651
1
EM491033
EM510971
EM491116
EM502650
PULLEY, DRIVEN BELT
1
PUMP, HYDROSTATIC ........................ 1 ............INCLUDES ITEM/
*
V-BELT, DRIVE
1
1
WASHER, FAN SECURING
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — VIBRATORY DRIVE ASSY.
VIBRATORY DRIVE ASSY.
6
2
8
7
1
4
OLD STYLE
CLUTCH ASSY.
(DISCONTINUED)
3
18
20
2
5
1
13
12
15
NEW STYLE
CLUTCH ASSY.
13
14
11
7
16
17
9
18
19
NOTES:
INCLUDED WITH PULLEY
CLUTCH, ITEM 5.
1
INCLUDED WITH VIBRATORY
SHAFT, ITEM 8.
2
PAGE 52 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — VIBRATORY DRIVE ASSY.
VIBRATORY DRIVE ASSY.
NO
1
PART NO
EM963003
492622
EM504451
EM502630
EM502133
PART NAME
QTY.
REMARKS
SCREW, HHC 1/4 - 20 X 3/4
WASHER, LOCK 1/4
WASHER, FLAT 1/4
SPACER
1
1
1
1
1
1
2
2
3
4
5
CLUTCH ASSY.
SET SCREW
RING, SNAP
6
*
7
EM9260967
EM500131
EM492365
EM491032
EM502625
492468
EM500133
16628388
EM500194
JISB2804C25
492179
EM502629
EM504233
8
9
SHAFT, ENGINE DRIVE .........................1............... INCLUDES ITEM W/
*
SCREW, HHC 5/16 - 18 X 1-1/4
PULLEY, DRIVE BELT
6
1
1
2
11
12
13@
14
15@
16
17
18
19
20
KEY, 1/4 X 25MM
SCREW, SET 5/16 - 18 X 1/2
COMPLETE CLUTCH ASSY. .................. 1 .............. INCLUDES ITEMS W/@
SPIDER COUPLING
KEY, 1/4 X 25MM
1
2
1
2
1
1
RING, SNAP
BEARING, FLANGE
FLANGE, ENGINE DRIVE SUPPORT
V-BELT, VIBRATORY DRIVE
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — VIBRATORY ROLL ASSY.
VIBRATORY ROLL ASSY.
9
7
4
8
6
31
32
15
3
2
13
14
5
1
12
34
42
17
11
12
10
11
10
33
23
22
40
26
21
41
20
19
30
27
24
25
22
37
28
38
11
29
11
23
18
38
43
11
35
44
26
39
19
20
29
27
36
25
24
PAGE 54 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — VIBRATORY ROLL ASSY.
VIBRATORY ROLL ASSY.
NO
1
PART NO
EM492555
EM492625
EM492599
EM490981
EM490951
EM490163
EM502134
EM502646
EM502645
EM492356
EM492622
EM491086
EM501299
EM502625
EM502135
EM490300
EM491759
EM500913
EM504456
EM492626
EM503992
EM504441
EM504457
EM509470
EM490985
EM502538
EM492160
511771
EM511777
EM492299
EM492625
EM492453
EM511775
504741
EM512272
EM503990
EM492396
492395
EM505010
EM916019
EM510520
EM490300
EM491703
EM503655
PART NAME
QTY.
1
REMARKS
NUT, HEX 7/16 - 14
2
WASHER, LOCK 7/16
WASHER, FLAT 7/16
RING, SNAP
1
3
1
4
1
5
RING, SNAP
1
6
BEARING, IDLER PULLEY
PULLEY, IDLER PULLEY
BUSHING, IDLER PULLEY
SHAFT, IDLER PULLEY
SCREW, HHC 1/4 - 20 X 3/4
WASHER, LOCK 1/4
1
7
1
8
1
9
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
1
11
1
WASHER, FLAT 1/4
WASHER, FLAT FENDER 1/4
KEY, 1/4 X 1
1
1
PULLEY, VIBRATORY CONTROL
PULLEY, GEAR DRIVE
KEY, WOODRUFF 1/8 X 1/2
DRIVE, GEAR REDUCTION ASSY.
SCREW, 1/2 - 13 X 3/4
WASHER, LOCK 1/2
1
1
1
1
5
5
PLATE, DRIVE SUPPORT
MOUNT, SHOCK
1
5
WASHER, FLAT FENDER 9/16
WASHER
5
2
RING, SNAP
2
CAP, BEARING
2
BEARING, SHAFT
2
HOUSING, LH BEARING, OPEN
SEAL
1
2
SCREW, HHC 5/16 - 18 X 1/2
WASHER, LOCK 7/16
SCREW, HHC 7/16 - X 1
SHAFT, ECCENTRIC VIBRATORY
ROLLER
2
12
12
1
1
BEARING, PILLOW BLOCK ASSY.
PLATE, ROLLER SUPPORT
SCREW, HHC 1/2 - 13 X 2
SCREW, HHC 1/2 - 13 X 1- 3/4
SUPPORT, ROLLER
GREASE FITTING
1
1
3
2
1
1
EXTENSION, ZERK
1
PULLEY, GEAR DRIVE
ZERK FITTING 1/8 NPT
HOUSING, RH BEARING, CLOSED
1
1
1
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — BATTERY ASSY.
BATTERY ASSY.
7
8
9
6
10
11
5
15
14
16
12
2
4
3
3
3
13
1
2
PAGE 56 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — BATTERY ASSY.
BATTERY ASSY.
NO
1
PART NO
EM507583
505401
EM923343
EM505201
EM507591C
507590
EM506429
EM505333
EM923343
EM923023
EM506302C
EM505249
492553
EM506430
EM963610
3019092
PART NAME
QTY.
1
REMARKS
BASE, BATTERY MOUNTING
SCREW, HHC 5/16 - 18 X 1/2
WASHER, LOCK 5/16
2
4
3
8
4
BUSHING, RUBBER SHOCK
CABLE, NEGATIVE BATTERY
BATTERY 12V.
BRACKET, BATTERY HOLD-DOWN
NUT, WING 5/16 - 18
WASHER, LOCK 5/16
4
5
1
6
1
7
1
8
2
9
2
10
11
12
13
14
15
16
WASHER, FLAT 9.5 X 22.2
CABLE, POSITIVE BATTERY
GROMMET
2
1
1
NUT, HEX 5/16 - 18
4
HOOK, BATTERY HOLD-DOWN
SCREW, HHC 3/8 - 16 X 1-1/4
WASHER, FLAT 3/8
2
1
1
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — SPRAY ASSY.
SPRAY ASSY.
PAGE 58 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — SPRAY ASSY.
SPRAY ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
EM491260
EM508578
EM508582
EM508614
492364
ELBOW, CONNECTOR
CONNECTOR
1
1
1
1
2
2
2
1
1
1
1
1
1
2
3
FILTER, Y-CONNECTOR
BAR ASSY.
SCREW, HHC 5/16 - 18 X 1
WASHER, LOCK 5/16
CLAMP
HOSE
VALVE, SHUT-OFF
PLUG
SCREW, HHC 3/8 - 16 X 3/4
WASHER, LOCK 3/8
WASHER, 3/8
4
5
6
EM923343
351104770
EM508615
EM505144
EM508579
492373
7
8
9
10
11
12
13
0166A
EM504679
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — TRANSMISSION ASSY.
TRANSMISSION
PAGE 60 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
V304 — TRANSMISSION ASSY.
TRANSMISSION
NO
PART NO
EM502546
EM502547
EM491722
EM492302
EM492228
EM490990
EM492123
EM490968
EM503802
EM503803
492451
PART NAME
QTY.
REMARKS
1
TRANSMISSION BASE BOX
TRANSMISSION COVER BOX
SPIRAL PIN
1
1
2
9
2
1
1
1
1
2
6
6
6
1
1
1
6
2
1
1
1
1
2
1
1
1
1
2
2
2
2
*
2
*
3
*
4
SPECIAL CAP SCREW
BEARING
*
5
*
6
INTERNAL RETAINING RING
SEAL
*
7
*
8
EXTERNAL RETAINING RING
GEAR
*
9
*
10
PIN
*
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SPECIAL CAP SCREW
LOCK WASHER, 3/8"
FLAT WASHER, 3/8"
COVER
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
0166A
3019092
EM502556
EM492122
EM491057
EM492258
EM492229
EM502550
EM502552
EM502551
EM490952
EM492212
EM502553
EM502555
EM492108
EM491058
EM492254
2101402
SEAL
O-RING
HEX SOCKET HEAD BOLT
BEARING
SHAFT
GEAR
KEY
EXTERNAL RETAINING RING
BEARING
SHAFT
COVER
SEAL
O-RING
HEX SOCKET HEAD BOLT
LOCK WASHER, 1/4"
O-RING
EM491056
EM492325
EM500913
CAP SCREW
TRANSMISSION ASSY. ....................................... 1 ............ INCLUDES ITEM/
*
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
PAYMENT TERMS
Terms of payment for parts are net 30 days.
FREIGHT POLICY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
LIMITATIONS OF SELLER’S LIABILITY
MINIMUM ORDER
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
RETURNED GOODS POLICY
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
PAGE 62 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Mayco Parts
Warranty Department
800-306-2926
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
800-421-1244, Ext. 279
310-537-3700, Ext. 279
Fax: 310-537-1173
Fax: 310-631-5032
Service Department
Technical Assistance
800-421-1244
310-537-3700
Fax: 310-537-4259
800-478-1244
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Lancashire OL7 0TL
Tel: 0161 339 2223
Fax: 0161 339 3226
Contact: [email protected]
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Fax: (450) 625-8664
© COPYRIGHT 2009, MULTIQUIP INC.
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property
of their respective owners and used with permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|