Multiquip Biscuit Joiner MVC88VTH User Manual
OperatiOn and parts Manual  
SERIES  
MODEL MVC88VTH  
MODEL MVC88VTHW  
ONE-WAY pLATE COMpACTOR  
(HONDA GX160UT2QMX2 GASOLINE ENGINE)  
Revision #2 (12/09/13)  
To find the latest revision of this  
publication, visit our website at:  
www.multiquip.com  
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TAbLE Of CONTENTS  
Honda GX160UTQMX2 Engine  
Component Drawings  
MVC88VTH/MVC88VTHW  
forward plate Compactor  
Proposition 65 Warning ........................................... 2  
Table Of Contents.................................................... 4  
Parts Ordering Procedures...................................... 5  
Safety Information .............................................. 6-10  
Specifications ........................................................ 11  
Dimensions............................................................ 12  
General Information............................................... 13  
Compactor Components........................................ 14  
Compactor Components........................................ 15  
Inspection .............................................................. 16  
Inspection .............................................................. 17  
Startup.............................................................. 18-19  
Operation............................................................... 20  
Operation/Maintenance ......................................... 21  
Maintenance..................................................... 22-25  
Explanation Of Code In Remarks Column............. 26  
Suggested Spare Parts ......................................... 27  
Cylinder Head Assembly .................................. 42-43  
Cylinder Barrel Assembly ................................. 44-45  
Crankcase Cover Assembly ............................. 46-47  
Crankshaft Assembly........................................ 48-49  
Piston Assembly............................................... 50-51  
Camshaft Assembly.......................................... 52-53  
Recoil Starter Assembly................................... 54-55  
Fan Cover Assembly......................................... 56-57  
Carburetor Assembly........................................ 58-59  
Air Cleaner Assembly....................................... 60-61  
Muffler Assembly.............................................. 62-63  
Fuel Tank Assembly.......................................... 64-65  
Flywheel Assembly........................................... 66-67  
Ignition Coil Assembly ...................................... 68-69  
Control Assembly ............................................. 70-71  
Decals............................................................... 72-73  
Terms and Conditions of Sale — Parts ................. 74  
Compactor Component Drawings  
Body Assembly................................................. 28-31  
Vibrator Assembly ............................................ 32-33  
Transport Wheel Assembly............................... 34-35  
Sprinkler Assembly........................................... 36-37  
Urethane Plate Assembly................................. 38-39  
Nameplate and Decals ..................................... 40-41  
NOTICE  
Specifications and part numbers are subject to change  
without notice.  
page 4 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
pARTS ORDERING pROCEDURES  
Ordering parts has never been easier!  
Choose from three easy options:  
Effective:  
January 1st, 2006  
best deal!  
Order via internet (dealers Only):  
Order parts on-line using Multiquip’s SmartEquip website!  
If you have an MQ Account, to obtain a Username  
and Password, E-mail us at: parts@multiquip.  
com.  
I View Parts Diagrams  
I Order Parts  
I Print Specification Information  
To obtain an MQ Account, contact your  
District Sales Manager for more information.  
Use the internet and qualify for a 5% discount  
on Standard orders for all orders which include  
complete part numbers.*  
Goto www.multiquip.com and click on  
to log in and save!  
Order Parts  
Note: Discounts Are Subject To Change  
Fax your order in and qualify for a 2% discount  
on Standard orders for all orders which include  
complete part numbers.*  
Order via Fax (dealers Only):  
All customers are welcome to order parts via Fax.  
domestic (us) Customers dial:  
1-800-6-PARTS-7 (800-672-7877)  
Note: Discounts Are Subject To Change  
domestic (us) dealers Call:  
1-800-427-1244  
Order via phone:  
non-dealer Customers:  
International Customers should contact  
their local Multiquip Representatives for  
Parts Ordering information.  
Contact your local Multiquip Dealer for  
parts or call 800-427-1244 for help in  
locating a dealer near you.  
When ordering parts, please supply:  
Ì
dealer account number  
Ì
specify preferred Method of shipment:  
Ì
Ì
Ì
Ì
Ì
dealer name and address  
ꢀ UPS/Fed Ex ꢀ  
Priority One ꢀ  
DHL  
Truck  
I
shipping address (if different than billing address)  
Return Fax number  
applicable Model number  
I
Ground  
I Next Day  
I
Second/Third Day  
quantity, part number and description of each part  
NOTICE  
All orders are treated as Standard Orders and will  
ship the same day if received prior to 3PM PST.  
We aCCepT aLL MaJOR CRediT CaRds!  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETY INfORMATION  
Do not operate or service the equipment before reading  
the entire manual. Safety precautions should be followed  
at all times when operating this equipment.  
Failure to read and understand the safety  
messages and operating instructions could  
result in injury to yourself and others.  
Potential hazards associated with the operation of this  
equipment will be referenced with hazard symbols which  
may appear throughout this manual in conjunction with  
safety messages.  
saFeTy Messages  
The four safety messages shown below will inform you  
about potential hazards that could injure you or others.The  
safety messages specifically address the level of exposure  
to the operator and are preceded by one of four words:  
dangeR,WaRning, CauTiOn or nOTiCe.  
saFeTy syMbOLs  
dangeR  
Indicates a hazardous situation which, if not avoided,  
WiLL result in deaTH or seRiOus inJuRy.  
WaRning  
Indicates a hazardous situation which, if not avoided,  
COuLd result in deaTH or seRiOus inJuRy.  
CauTiOn  
Indicates a hazardous situation which, if not avoided,  
COuLd result in MinOR or MOdeRaTe inJuRy.  
NOTICE  
Addresses practices not related to personal injury.  
page 6 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETY INfORMATION  
geneRaL saFeTy  
NOTICE  
CauTiOn  
„ This equipment should only be operated by trained and  
qualified personnel 18 years of age and older.  
„ neVeR operate this equipment without proper protective  
clothing, shatterproof glasses, respiratory protection,  
hearing protection, steel-toed boots and other protective  
devices required by the job or city and state regulations.  
„ Whenever necessary, replace nameplate, operation and  
safety decals when they become difficult read.  
„ Manufacturer does not assume responsibility for any  
accident due to equipment modifications. Unauthorized  
equipment modification will void all warranties.  
„ neVeR use accessories or attachments that are not  
recommended by Multiquip for this equipment. Damage  
to the equipment and/or injury to user may result.  
„ neVeR operate this equipment when not  
feeling well due to fatigue, illness or when  
under medication.  
„ aLWays know the location of the nearest  
„ neVeR operate this equipment under the influence of  
drugs or alcohol.  
fire extinguisher.  
„ aLWays know the location of the nearest  
first aid kit.  
„ aLWaysknow the location of the nearest phone or keep  
a phone on the job site. Also, know the phone numbers  
of the nearest ambulance,doctorand fire department.  
This information will be invaluable in the case of an  
emergency.  
„ aLWays check the equipment for loosened threads or  
bolts before starting.  
„ dO nOT use the equipment for any purpose other than  
its intended purposes or applications.  
„ aLWays clear the work area of any debris, tools, etc.  
that would constitute a hazard while the equipment is  
in operation.  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETY INfORMATION  
COMpaCTOR saFeTy  
WaRning  
dangeR  
„ dO nOT place hands or fingers inside engine  
compartment when engine is running.  
„ neVeRoperate the equipment in an explosive  
atmosphere or near combustible materials.An  
explosion or fire could result causing severe  
bodily harm or even death.  
„ neVeR operate the engine with heat shields or  
guards removed.  
„ Keep fingers, hands hair and clothing away  
from all moving parts to prevent injury.  
WaRning  
„ neVeR disconnect any emergency or safety devices.  
These devices are intended for operator safety.  
Disconnection of these devices can cause severe injury,  
bodily harm or even death.Disconnection of any of these  
devices will void all warranties.  
CauTiOn  
„ neVeR touch the hot exhaust manifold,  
muffler or cylinder. Allow these parts to  
cool before servicing equipment.  
NOTICE  
CauTiOn  
„ neVeR run engine without an air filter or with a dirty air  
filter.Severe engine damage may occur.Service air filter  
frequently to prevent engine malfunction.  
„ neVeR lubricate components or attempt service on a  
running machine.  
NOTICE  
„ neVeR tamper with the factory settings  
of the engine or engine governor. Damage  
to the engine or equipment can result  
if operating in speed ranges above the  
maximum allowable.  
„ aLWays keep the machine in proper running condition.  
„ Fix damage to machine and replace any broken parts  
immediately.  
„ aLWays store equipment properly when it is not being  
used.Equipment should be stored in a clean, dry location  
out of the reach of children and unauthorized personnel.  
„ neVeR tip the engine to extreme angles during lifting as  
it may cause oil to gravitate into the cylinder head, making  
the engine start difficult.  
engine saFeTy  
dangeR  
„ The engine fuel exhaust gases contain poisonous carbon  
monoxide. This gas is colorless and odorless, and can  
cause death if inhaled.  
„ The engine of this equipment requires an adequate  
free flow of cooling air. neVeR operate this equipment  
in any enclosed or narrow  
area where free flow of the  
air is restricted. If the air  
flow is restricted it will cause  
injury to people and property  
and serious damage to the  
equipment or engine.  
page 8 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETY INfORMATION  
FueL saFeTy  
baTTeRy saFeTy (eLeCTRiC sTaRT OnLy)  
dangeR  
dangeR  
„ dO nOT add fuel to equipment if it is placed inside truck  
bed with plastic liner. Possibility exists of explosion or  
fire due to static electricity.  
„ dO nOT drop the battery. There is a possibility that the  
battery will explode.  
„ dOnOTexpose the battery to open flames,  
sparks, cigarettes, etc.The battery contains  
combustible gases and liquids. If these  
gases and liquids come into contact with a  
flame or spark, an explosion could occur.  
FUEL  
WaRning  
„ aLWays wear safety glasses when  
handling the battery to avoid eye irritation.  
The battery contains acids that can cause  
injury to the eyes and skin.  
FUEL  
„ Use well-insulated gloves when picking up  
the battery.  
„ aLWays keep the battery charged. If the battery is not  
charged, combustible gas will build up.  
„ dO nOTstart the engine near spilled fuel or combustible  
fluids. Diesel fuel is extremely flammable and its vapors  
can cause an explosion if ignited.  
„ dO nOT charge battery if frozen. Battery can explode.  
When frozen, warm the battery to at least 61°F (16°C).  
„ aLWays refuel in a well-ventilated area, away from  
sparks and open flames.  
„ aLWays recharge the battery in a well-ventilated  
environmenttoavoidtheriskofadangerousconcentration  
of combustible gases.  
„ aLWays use extreme caution when working with  
flammable liquids.  
„ If the battery liquid (dilute sulfuric acid)  
comes into contact with clothing or skin,  
rinse skin or clothing immediately with  
plenty of water.  
„ dO nOT fill the fuel tank while the engine is running  
or hot.  
„ dO nOT overfill tank, since spilled fuel could ignite if it  
comes into contact with hot engine parts or sparks from  
the ignition system.  
„ If the battery liquid (dilute sulfuric acid) comes into  
contact with eyes, rinse eyes immediately with plenty  
of water and contact the nearest doctor or hospital to  
seek medical attention.  
„ Store fuel in appropriate containers, in well-ventilated  
areas and away from sparks and flames.  
CauTiOn  
„ neVeR use fuel as a cleaning agent.  
„ aLWays disconnect the negaTiVe battery terminal  
before performing service on the equipment.  
„ dO nOT smoke around or near the  
equipment. Fire or explosion could result  
from fuel vapors or if fuel is spilled on a  
hot engine.  
„ aLWayskeep battery cables in good working condition.  
Repair or replace all worn cables.  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETY INfORMATION  
„ When the life cycle of this equipment is over, remove  
battery and bring to appropriate facility for lead  
reclamation. Use safety precautions when handling  
batteries that contain sulfuric acid.  
TRanspORTing saFeTy  
CauTiOn  
„ NEVER allow any person or animal to stand underneath  
the equipment while lifting.  
„ When the life cycle of this equipment is over, it is  
recommended that the trowel frame and all other metal  
parts be sent to a recycling center.  
NOTICE  
Metal recycling involves the collection of metal from  
discarded products and its transformation into raw  
materials to use in manufacturing a new product.  
„ Before lifting, make sure that the equipment parts (hook  
and vibration insulator) are not damaged and screws are  
not loose or missing.  
Recyclers and manufacturers alike promote the process  
of recycling metal. Using a metal recycling center  
promotes energy cost savings.  
„ Always make sure crane or lifitng device has been  
properly secured to the lifting bail (hook) of the  
equipment.  
eMissiOns inFORMaTiOn  
„ aLWays shutdown engine before transporting.  
NOTICE  
„ neVeR lift the equipment while the engine is running.  
The gasoline engine used in this equipment has been  
designed to reduce harmful levels of carbon monoxide  
(CO), hydrocarbons (HC) and nitrogen oxides (NOx)  
contained in gasoline exhaust emissions.  
„ Tighten fuel tank cap securely and close fuel cock to  
prevent fuel from spilling.  
„ Use adequate lifting cable (wire or rope) of sufficient  
strength.  
This engine has been certified to meet US EPA Evaporative  
emissions requirements in the installed configuration.  
„ Use one point suspension hook and lift straight  
upwards.  
Attempting to modify or make adjustments to the engine  
emmission system by unauthorized personnel without  
proper training could damage the equipment or create an  
unsafe condition.  
„ dO nOT lift machine to unnecessary heights.  
„ aLWays tie down equipment during transport by  
securing the equipment with rope.  
Additionally, modifying the fuel system may adversely affect  
evaporative emissions, resulting in fines or other penalties.  
enViROnMenTaL saFeTy/deCOMMissiOning  
NOTICE  
emission Control Label  
Decommissioning is a controlled process used to safely  
retire a piece of equipment that is no longer serviceable.  
If the equipment poses an unacceptable and unrepairable  
safety risk due to wear or damage or is no longer cost  
effective to maintain (beyond life-cycle reliability) and is to  
be decommissioned (demolition and dismantlement),be  
sure to follow rules below.  
The emission control label is an integral part of the emission  
system and is strictly controlled by regulation(s).  
The label must remain with the engine for its entire life.  
If a replacement emission label is needed, please contact  
your authorized engine distributor.  
„ dO nOT pour waste or oil directly onto the ground, down  
a drain or into any water source.  
„ Contact your country's Department of  
Public Works or recycling agency in your  
area and arrange for proper disposal of  
any electrical components, waste or oil  
associated with this equipment.  
page 10 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SpECIfICATIONS  
Table 1. MVC88VTH/VTHW One-Way  
plate Compactor specifications  
Centrifugal Force  
3,372 lbs. (1,530 kg)  
Vibration Frequency  
Traveling Speed  
6,000 vpm (60 Hz)  
82 ft/min (25 m/min)  
Plate Size (L x W)  
19.7 x 20.7 in (.500 x .525 mm)  
8,100 sq. ft./hr (752 sq. m/hr)  
Max. Area of Compaction (no extensions)  
Operating Weight MVC88VTGH  
Operating Weight MVC88VTHW  
207 lbs. (95 kg.)  
229 lbs. (104 kg.)  
Water Tank Capacity  
Anti-Vibration Handle  
13.7 qt (13.0 liters)  
Yes  
Lubricating Oil in Vibration Case  
6.7 fl. oz. (200 cc)  
Table 2. engine specifications  
Engine Make  
Engine Model  
HONDA  
GX160UT2QMX2  
Air-cooled 4 stroke, Single Cylinder, OHV,  
Horizontal Shaft Gasoline Engine  
2.7 in. x 1.8 in. (68 mm x 45 mm)  
163 cc (9.9 cu-in)  
Engine Type  
Cylinder Bore X Stroke  
Displacement  
Maximum Ouput  
Fuel Tank Capacity  
Fuel Type  
4.8 HP (3.6 kW) @ 3600 RPM  
Approx. .825 U.S. gallons (3.1 liters)  
Unleaded 86 Octane or Higher  
.61 qts (0.58 liters)  
Oil Capacity  
Air Cleaner  
Dual Element  
Starting Method  
Recoil Start  
Dry Net Weight Recoil/Electric  
Dimensions (L x W x H)  
33 lbs (15 Kg.)  
12.2 x 14.3 x 13.6 in (312 x 362 x 346 mm)  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIMENSIONS  
A
D
B
C
E
Figure 1. Dimensions  
Table 3. dimensions  
ReF. des  
in. (MM)  
24.5 (622)  
22.5 (571)  
43.5 (1,105)  
36.0 (914)  
19.7 (500)  
A
B
C
D
E
page 12 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GENERAL INfORMATION  
deFiniTiOn OF pLaTe COMpaCTOR  
FRequenCy/speed  
The Mikasa MVC88VTH/VTHW is a walk behind, plate  
compactor designed for the compaction of sand, mixed soils  
and asphalt.This plate compactor is a powerful compacting  
tool capable of applying a tremendous force in consecutive  
high frequency vibrations to a soil surface. Its applications  
include compacting for road, embankments and reservoirs  
as well as backfilling for gas pipelines, water pipelines and  
cable installation work.  
The compactor's vibrating plate produces a vibration  
frequency of 6,000 VPM (vibrations per minute). The  
travel speed of the compactor is approximately 82 ft/  
minute (25 meters/minute).  
engine  
These plate compactors are equipped with a Honda  
GX160UT2QMX2 air cooled, 4-cycle gasoline engine.  
The engine drives an eccentric weight at a high speed to  
develop a compaction force.  
VibRaTORy pLaTes  
The vibratory plates of the compactor produce low  
amplitude high frequency vibrations, designed to compact  
granular soils and asphalt.  
In addition this engine is equipped with an oil alertsystem  
that will automatically stop the engine before the engine  
falls below safe engine oil operating limits. Always be sure  
to check the engine oil level prior to starting the engine.  
The resulting vibrations cause forward motion.The engine  
and handle are vibration isolated from the vibrating plate.  
COnTROLs  
Before starting the plate compactor identify and understand  
the function of all the controls and components.  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMpACTOR COMpONENTS  
MVC88VTHW  
1
MVC88VTH  
2
3
9
4
8
10  
5
OFF  
6
ON  
7
11  
Figure 2. Plate Compactor Components  
Figure 2 shows the location of the basic controls and  
components of the MVC88VTH/VTHW Plate Compactor.  
The function of each control is described below:  
7. WaterTube-sprinkler (VTHW Only) – Supplies water  
to the soil via a splash plate.  
8. Water shut-OffValve (VTHW Only) – Turn this valve  
downward to let water flow from the water tank to the  
water tube.  
1. Handle bar – When operating the compactor use this  
handle bar to manuever the compactor.  
2. Lifting bale –When lifting of the compactor is required  
either by forklift, crane etc., tie rope or chain around  
this lifting point.  
9. engine – These plate compactors use a Honda  
GX160, 4.8 HP, air-cooled 4 stroke gasoline engine.  
Refer to the Honda owner's manual for more detailed  
engine information and related topics.  
3. Fuel Tank Cap – Remove this cap to add fuel. Use  
only unleaded fuel with an octane rating of 86 or higher  
10. belt Cover – Remove this cover to gain acess to the  
V-belts. neVeR run the compactor without the V-belt  
cover. If the V-belt cover is not installed, the possibility  
exists that your hand may get caught between theV-belt  
and clutch, causing serious injury and bodily harm.  
4. WaterTank Cap (VTHW Only) – Remove this cap to  
add water to the water tank.  
5. WaterTank (VTHW only) – Holds 13.7 quarts of water  
(removable, no tools required).  
11. eccentric Housing – Encloses the eccentric, gears  
and counter weights.  
6. Vibrating plate – A flat, open plate made of durable  
cast iron construction used in the compacting of soil.  
page 14 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMpACTOR COMpONENTS  
1
9
8
2
7
12  
6
5
11  
10  
4
3
Figure 3. Engine Controls and Components  
iniTiaL seRViCing  
6. air Cleaner – Prevents dirt and other debris from  
entering the fuel system. Remove wing-nut on top of  
air filter canister to gain access to filter element.  
The engine (Figure 3) must be checked for proper  
lubrication and filled with fuel prior to operation.Refer to the  
manufacturer's engine manual for instructions and details  
of operation and servicing.  
NOTICE  
1. Fuel Filler Cap – Remove this cap to add unleaded  
gasoline to the fuel tank. Make sure cap is tightened  
securely. dO nOT over fill.  
Operating the engine without an air filter, with a  
damaged air filter, or a filter in need of replacement  
will allow dirt to enter the engine, causing rapid engine  
wear.  
dangeR  
Add fuel to the tank only when the engine  
is stopped and has had an opportunity to  
cool down. In the event of a fuel spill, dO  
nOT attempt to start the engine until the  
fuel residue has been completely wiped up  
and the area surrounding the engine is dry.  
7. spark plug – Provides spark to the ignition system.  
Set spark plug gap according to engine manufacturer's  
instructions. Clean spark plug once a week.  
8. Muffler– Used to reduce noise and emissions.neVeR  
touch when hot!  
9. Fuel Tank – Fill with unleaded gasoline. Reference  
Table 2 for fuel tank capacity.For additional information  
refer to Honda engine owner's manual.  
2. Throttle Lever – Used to adjust engine RPM speed.  
For normal operation this lever should always be placed  
in the Run position.  
10. dipstick/OilFillerCap – Remove this cap to determine  
if the engine oil is low. Add oil through this filler port as  
recommended in (Table 4).  
3. Recoil starter (pull Rope) – Manual-starting method.  
Pull the starter grip until resistance is felt, then pull  
briskly and smoothly.  
11. Oil drain plug – Remove this plug to remove oil from  
the engine's crankcase.  
4. Fuel Valve Lever – Open to let fuel flow, CLOse to  
stop the flow of fuel.  
12. engine On/OFF switch – On position permits engine  
5. Choke Lever – Used in the starting of a cold engine,  
or in cold weather conditions. The choke enriches the  
fuel mixture.  
starting, OFF position stops engine operation.  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSpECTION  
before starting  
dangeR  
eXpLOsiVe FueL!  
1. Read all safety instructions at the beginning of manual.  
2. Clean the compactor, removing dirt and dust,  
particularly the engine cooling air inlet, carburetor and  
air cleaner.  
Motor fuels are highly flammable and can  
be dangerous if mishandled. dO nOT  
smoke while refueling. dO nOT attempt  
to refuel the compactor if the engine is  
hot! or running.  
3. Check the air filter for dirt and dust. If air filter is dirty,  
replace air filter with a new one as required.  
4. Check carburetor for external dirt and dust. Clean with  
dry compressed air.  
Fuel Check  
1. Visually inspect (Figure 6) to see if fuel level is low. If  
fuel is low, replenish with unleaded fuel.  
5. Check fastening nuts and bolts for tightness.  
engine Oil Check  
FUEL  
CAP  
1. To check the engine oil level, place the compactor on  
secure level ground with the engine stopped.  
2. Remove the dipstick from the engine oil filler hole  
(Figure 4) and wipe clean.  
Figure 6. Fuel Check  
Figure 4. Engine Oil Dipstick Removal  
2. When refueling, be sure to use a strainer for filtration.  
dO nOT top-off fuel. Wipe up any spilled fuel  
immediately.  
3. Insert and remove the dipstick without screwing it into  
the filler neck.Check the oil level shown on the dipstick.  
4. If the oil level is low (Figure 5), fill to the edge of the  
oil filler hole with the recommended oil type as listed  
in Table 4. Reference Table 2 for maximum engine oil  
capacity.  
WaterTank (Option)  
If your unit is equipped with a water tank (Figure 7) and  
your applications requires water, fill water tank.  
WATER  
SOURCE  
WATER  
TANK  
Figure 5. Engine Oil Dipstick (Oil Level)  
Table 4. OilType  
season  
Summer  
Spring/Fall  
Winter  
Temperature  
25°C or Higher  
25°C~10°C  
OilType  
SAE 10W-30  
SAE 10W-30/20  
SAE 10W-10  
Figure 7. Water Tank Filling  
0°C or Lower  
page 16 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSpECTION  
V-beLT  
V-beltTension  
TheV-belt tension is proper if theV-belt bends 10 to 15 mm  
(Figure 10) when depressed with finger at midway between  
the clutch and vibrator pulleys.  
V-belt Cover Removal  
To inspect the V-belt, remove the three bolts that secure  
the belt cover to the frame as shown in Figure 8.  
REMOVE  
CORRECT V-BELT  
TENSION 10-15 MM  
VIBRATOR  
CLUTCH  
WHEN DEPRESSED  
PULLEY  
AS SHOWN.  
REMOVE  
V-BELT  
V-BELT  
Mikasa  
VIBRATOR  
PULLEY  
V-BELT COVER  
Figure 10. V-Belt Tension  
Figure 8. V-Belt Cover Removal  
Vibrator Oil Check  
V-belt inspection  
1. Place the plate compactor horizontally on a flat surface.  
Make sure the compactor is level when checking the  
oil in the vibrator assembly.  
Visually examine the V-belt (Figure 9) and determine if it  
is full of tiny cracks, frayed, has pieces of rubber missing,  
is peeling or otherwise damaged.  
2. Check vibrator oil level by removing the oil plug (vibrator  
oil gauge) as shown in Figure 11. The oil level should  
be up to the oil plug.  
Also, examine the belt and determine if it is oil soaked or  
"glazed " (hard shiny appearance on the sides of the belt).  
Either of these two conditions can cause the belt to run hot,  
which can weaken it and increase the danger of it breaking.  
3. The vibrator holds approximately 6.7 oz. (200 cc).  
iMpORTanT, if oil is required, replace using only SAE  
10W-30 motor oil.  
If the V-belt exhibits any of the referenced wear conditions  
replace the V-belt immediately  
OIL SOAKED  
VIBRATOR  
OIL PLUG  
PACKING  
CORD FAILURE  
GLAZED  
WORN BACK  
COVER  
BROKEN  
Figure 11. Vibrator Oil Check  
MISSING RUBBER  
CRACKS  
SIDEWALL  
WEAR  
Figure 9. Drive Belt Inspection  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STARTUp  
3. Place the choke lever (Figure 14) in the “CLOsed”  
position if starting a cold engine.  
CauTiOn  
dOnOTattempt to operate the compactor  
until the Safety, General Information and  
Inspection sections of this manual have  
been read and thoroughly understood.  
CHOKE LEVER  
This section is intended to assist the operator with the  
initial start-up of the compactor. It is extremely important  
that this section be read carefully before attempting to use  
the compactor in the field.  
sTaRTingTHe engine  
CLOSED  
1. Place the engine fuel valve lever (Figure 12) to the  
“On” position.  
Figure 14. Choke Lever (Closed)  
NOTICE  
The CLOsed position of the choke lever enriches the  
fuel mixture for starting a COLd engine. The Open  
position provides the correct fuel mixture for normal  
operation after starting, and for restarting a warm  
engine.  
4. Place the engine ON/OFF switch (Figure 15) in the  
"On" position.  
Figure 12. Engine FuelValve Lever (ON Position)  
2. Move the throttle lever (Figure 13) away from the idle  
position, about 1/3 of the way toward the run position.  
Figure 15. Engine ON/OFF Switch (ON Position)  
5. Grasp the starter grip (Figure 16) and slowly pull it  
out. The resistance becomes the hardest at a certain  
position, corresponding the compression point.Rewind  
the rope a little from that point and pull out sharply.  
Figure 13. Throttle Lever (1/3 Start Position)  
page 18 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STARTUp  
9. If the sprinkling of water is required, place water valve  
in the On position.  
OFF  
ON  
Figure 18. Water Valve (ON)  
Figure 16. Starter Grip  
10. To begin compacting, place the throttle lever (Figure 19)  
in the “Run” position.  
NOTICE  
dO nOT pull the starter rope all the way to the end  
dO nOT release the starter rope after pulling. Allow it  
to rewind as soon as possible.  
6. When engine starts, release the starter grip and allow  
the rope to recoil.  
7. If the choke lever was moved to the "CLOsed"position  
to start the engine gradually move it to the "Open"  
position (Figure 17) as the engine warms up. If the  
engine has not started repeat steps 1 through 6.  
CHOKE  
LEVER  
Figure 19. Throttle Lever (Run)  
OPEN  
Figure 17. Choke Lever (Open)  
8. Before the compactor is placed in to operation, run the  
engine for several minutes. Check for fuel leaks, and  
noises that would associate with a lose component.  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OpERATION  
OpeRaTiOn  
sTOppingTHe engine  
CauTiOn  
aLWays follow all safety rules referenced  
normal shutdown  
1. Move the throttle lever to the idle position (Figure 20)  
and run the engine for three minutes at low speed.  
in the safety section of this manual before  
operating compactor. Keep work area  
clear of debris and other objects that  
could cause damage to the compactor or  
bodily injury.  
1. Once the engine has started, move the engine throttle  
lever quickly to the run position.  
2. With the throttle lever in the run position, the engine  
speed should be around 2,300 RPM, therefore  
engaging the centrifugal clutch.  
NOTICE  
Figure 20. Throttle Lever (Idle)  
aLWays move the throttle lever quickly without  
hesitation, because increasing the engine speed slowly  
causes the clutch to slip.  
2. Place the engine ON/OFF switch (Figure 21) in the  
"OFF" position.  
ENGINE SWITCH  
3. Firmly gasp the compactor's handle bar with both  
hands, the compactor will begin moving forward.  
OFF  
ON  
4. Slowly walk behind the compactor and be on the  
lookout for any large objects or foreign matter that  
might cause damage to the compactor or bodily injury.  
NOTICE  
Figure 21. Engine ON/OFF Switch (OFF Position)  
neVeR stop the engine suddenly while working at  
high speeds.  
3. Place the fuel shut-off lever (Figure 22) in the "OFF"  
position.  
5. Compactor traveling speed may drop on soils which  
contain clay, however there may be cases where  
traveling speed drops because the compaction plate  
does not leave the ground surface easily due to the  
composition of the soil. To rectify this problem do the  
following:  
„ Check the bottom plate to see if clay or equivalent  
material has been lodge in the plate mechanism. If so,  
wash with water and remove.  
Figure 22. Fuel Valve Lever (OFF)  
4. If applicable place water valve (Figure 18) in the OFF  
position.  
„ Remember the compactor does not work as efficiently  
on clay or soils that have a high moisture content level.  
emergency shutdown  
„ If the soil has a high moisture level, dry soil to appropriate  
moisture content level or carry out compaction twice.  
1. Move the throttle lever quickly to the idLeposition, and  
place the engine ON/OFF switch in the OFF position.  
page 20 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OpERATION/MAINTENANCE  
general Cleanliness  
MainTenanCe  
General maintenance practices are crucial to the  
performance and longevity of your compactor. This  
equipment requires routine cleaning, inspection and  
lubrication. Reference Table 5 and Table 6 for scheduled  
engine and compactor maintenance.  
Clean the compactor daily. Remove all dust and debris  
buildup (mud, clay etc.).If the compactor is steam-cleaned,  
ensure that lubrication is accomplished aFTeR steam  
cleaning.  
NOTICE  
The following procedures, devoted to maintenance, can  
prevent serious compactor damage or malfunctioning.  
Inspection and other services should always be carried  
out on hard and level ground with the engine shutdown.  
NOTICE  
NOTICE  
Reference HOnda engine manual supplied with your  
compactor for more detailed engine maintenance and  
troubleshooting.  
The inspection intervals listed in the maintenance tables  
are for operation under normal conditions. Adjust your  
inspection intervals based on the number hours plate  
compactor is in use, and particular working conditions.  
CauTiOn  
aLWays allow the engine to cool before  
servicing.neVeR attempt any maintenance  
work on a hot engine.  
CauTiOn  
aLWays disconnect the spark plug wire from the spark  
plug and secure away from the engine before performing  
maintenance or adjustments on the machine.  
WaRning  
Some maintenance operations may  
require the engine to be run. Ensure  
that the maintenance area is well  
ventilated. Gasoline engine exhaust  
contains poisonous carbon monoxide  
gas that can cause unconsciousness  
and may result in deaTH  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
inspection and Maintenance serviceTables  
To make sure your plate compactor is always in good  
working condition before using, carry out the maintenance  
inspection in accordance with Table 5 and Table 6.  
engine Maintenance  
Perform engine maintance as listed in Table 5.  
Table 5. engine Maintenance schedule  
First every 3  
before Month or Months or Months or year or  
every 6  
every  
every 2  
years or  
200 hrs  
description (3)  
Operation  
10 hrs  
25 hrs  
50 hrs  
100 hrs  
CHECK  
CHANGE  
CHECK  
X
X
Engine Oil  
Air Cleaner  
X
CHANGE  
X (1)  
All Nuts and  
Bolts  
Re-tighten If  
Necessary  
X
CHECK-CLEAN  
REPLACE  
CHECK  
X
X
Spark Plug  
X
Cooling Fins  
Spark Arrester  
Fuel Tank  
CLEAN  
X
X
CLEAN  
Fuel Filter  
CHECK  
X
Idle Speed  
CHECK-ADJUST  
X (2)  
Valve Clearance CHECK-ADJUST  
Fuel lines CHECK  
X (2)  
Every 2 years (replace if necessary) (2)  
1. Service more frequently when used in dusTy areas.  
2. These items should be serviced by your service dealer, unless you have the proper tools and are mechanically proficient.  
Refer to the HOnda Shop Manual for service procedures.  
3. For commercial use, log hours of operation to determine proper maintenance intervals.  
page 22 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
Machine inspection  
engine air Cleaner  
dangeR  
Perfom machine inspection as listed in Table 6.  
dO nOT use gasoline or low flash point  
solvents for cleaning the air cleaner. The  
possibility exists of fire or explosion which  
can cause damage to the equipment and  
severe bodily harm or even deaTH!  
Table 6. Machine inspection  
interval  
Check  
Machine  
solution  
Clean if necessary.  
Repair fuel leaks.  
Repair fuel leaks.  
Add oil if necessary.  
Add oil if necessary.  
Clean/Replace  
Fuel Tank For Leaks  
Fuel System for Leaks  
Engine Oil  
CauTiOn  
Daily Before Starting  
Vibrator Oil  
Wear protective equipment such as  
approved safety glasses or face shields  
and dust masks or respirators when  
cleaning air filters with compressed air.  
Air Cleaner Element  
Guard Frame  
Inspect/deformations  
Replace if damaged.  
Shock Absorber  
Replace only after  
first 20 hrs.  
Every 20 Hours  
Every 100  
Engine Oil  
This engine is equipped with a replaceable, high-density  
paper air cleaner element. See (Figure 23) for air cleaner  
components.  
Engine Oil  
Change  
Air Cleaner Element  
Clean/Replace  
1. Remove the air cleaner cover and foam filter element.  
Check oil level. Check  
for leaks.  
Vibrator Oil  
V-Belt  
2. Tap the paper filter element several times on a hard  
surface to remove dirt, or blow compressed air not  
exceeding 30 psi (207 kPa, 2.1 kgf/cm2) through the  
filter element from the inside out. neVeR brush off  
dirt. Brushing will force dirt into the fibers. Replace the  
paper filter element if it is excessively dirty.  
Inspect, replace if  
damaged or worn.  
Inspect, replace if not  
working properly.  
Clutch  
Every 200 hours  
Replace bolts  
if deformed or  
elongated.  
Engine Bolts  
Vibrator Oil  
Fuel Filter  
Fuel Lines  
Change  
Change  
Replace  
Every 300 hours  
Every 2 years  
TighteningTorque  
Reference Table 7 below (Tightening Torque ), for retight-  
ening of nuts and bolts.  
BLOW COMPRESSED  
AIR FROM THE  
INSIDE OUT  
Table 7. TighteningTorque (in. kg/cm diameter)  
Material 6mm  
8mm  
150  
250  
400  
10mm  
12mm  
14mm 16mm 18mm  
20mm  
2,000  
3,800  
5,600  
4T  
70  
300  
500  
750 1,100 1,400  
6-8T  
11T  
100  
150  
500  
800  
1,300 2,000 2,700  
2,000 2,900 4,200  
800  
1,200  
*
100 (6mm) 300 ~ 350 (8mm) 650 ~ 700 (10mm)  
In case counter-part is of aluminum  
**  
Bolt threads used with this machine are all right handed  
Material and quality of material is marked on each bolt, and screw.  
Figure 23. Engine Air Cleaner  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
3. Clean foam element in warm, soapy water or  
nonflammable solvent. Rinse and dry thoroughly. Dip  
the element in clean engine oil and completely squeeze  
out the excess oil from the element before installing.  
3. Thread spark plug into cylinder hole by hand to prevent  
cross-threading, then tighten securely.  
GAP  
.028 - .031 IN.  
(0.7- 0.8 MM.)  
NOTICE  
Operating the engine with loose or damaged air cleaner  
components could allow unfiltered air into the engine  
causing premature wear and failure.  
engine Oil  
Figure 25. Spark Plug Gap  
1. Drain the engine oil when the oil is warm as shown in  
(Figure 24).  
V-beLT  
Visually examine the V-belt (Figure 26) and determine if it  
is full of tiny cracks, frayed, has pieces of rubber missing,  
is peeling or otherwise damaged.  
OIL FILLER CAP  
DIPSTICK  
Also, examine the belt and determine if it is oil soaked or  
"glazed " (hard shiny appearance on the sides of the belt).  
Either of these two conditions can cause the belt to run hot,  
which can weaken it and increase the danger of it breaking.  
SEALING  
WASHER  
DRAIN  
BOLT  
If the V-belt exhibits any of the above wear conditions  
replace the V-belt immediately.  
Figure 24. Draining Engine Oil  
OIL SOAKED  
2. Remove the oil drain bolt and sealing washer and allow  
the oil to drain into a suitable container.  
3. Replace engine oil with recommended type oil as listed  
in Table 4. For engine oil capacity, see Table 2 (Engine  
Specifications). dO nOT overfill.  
4. Reinstall drain bolt with sealing washer and tighten  
securely.  
CORD FAILURE  
GLAZED  
WORN BACK  
COVER  
spaRk pLug  
NOTICE  
BROKEN  
neVeR use a spark plug of incorrect heat range.  
MISSING RUBBER  
1. Remove and clean spark plug (Figure 25) with a wire  
brush if it is to be reused. Discard spark plug if the  
insulator is cracked or chipped.  
CRACKS  
SIDEWALL  
WEAR  
2. Using a feeler gauge adjust spark plug gap to 0.028  
~0.031 inch (0.7~0.8 mm).  
Figure 26. V-Belt Inspection  
page 24 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
4. Carefully remove carbon deposits from the spark  
arrester screen (Figure 28) with a wire brush.  
spaRk aRResTeR CLeaning  
Clean the spark arrester every 6 months or 100 hours.  
WIRE  
1. Remove the 4 mm screw (3) from the exhaust deflector,  
then remove the deflector. See (Figure 27).  
BRUSH  
2. Remove the 5 mm screw (4) from the muffler protector,  
then remove the muffler protector.  
3. Remove the 4 mm screw from the spark arrestor, then  
remove the spark arrester  
SPARK  
ARRESTER  
SCREEN  
5MM SCREW (4)  
Figure 28. Cleaning The Spark Arrester  
5. If the spark arrester is damaged and has breaks or  
holes, replace with a new one.  
DEFLECTOR  
4MM SCREW (3)  
MUFFLER  
PROTECTOR  
6. Reinstall the spark arrester and muffler protector in  
reverse order of disassembly.  
4MM SCREW (1)  
SPARK  
ARRESTER  
Figure 27. Spark Arrester Removal  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXpLANATION Of CODE IN REMARKS COLUMN  
The following section explains the different symbols and  
qTy. Column  
remarks used in the Parts section of this manual. Use the  
help numbers found on the back page of the manual if there  
are any questions.  
numbers used — Item quantity can be indicated by a  
number, a blank entry, or A/R.  
A/R (As Required) is generally used for hoses or other  
parts that are sold in bulk and cut to length.  
NOTICE  
The contents and part numbers listed in the parts  
section are subject to change withoutnotice.Multiquip  
does not guarantee the availability of the parts listed.  
A blank entry generally indicates that the item is not sold  
separately.Other entries will be clarified in the “Remarks”  
Column.  
saMpLe paRTs LisT  
ReMaRks Column  
nO. paRT nO. paRT naMe  
qTy. ReMaRks  
Some of the most common notes found in the “Remarks”  
Column are listed below. Other additional notes needed  
to describe the item can also be shown.  
1
2%  
12345  
BOLT .....................1 .....INCLUDES ITEMS W/%  
WASHER, 1/4 IN. ..........NOT SOLD SEPARATELY  
WASHER, 3/8 IN. ..1 .....MQ-45T ONLY  
2% 12347  
3
4
12348  
12349  
HOSE ..................A/R ...MAKE LOCALLY  
BEARING ..............1 .....S/N 2345B AND ABOVE  
assembly/kit — All items on the parts list with the  
same unique symbol will be included when this item is  
purchased.  
nO. Column  
Indicated by:  
unique symbols — All items with same unique symbol  
(@, #, +, %, or >) in the number column belong to the  
same assembly or kit, which is indicated by a note in the  
“Remarks” column.  
“INCLUDES ITEMS W/(unique symbol)”  
serial number break — Used to list an effective serial  
number range where a particular part is used.  
duplicate itemnumbers — Duplicate numbers indicate  
multiple part numbers, which are in effect for the same  
general item, such as different size saw blade guards in  
use or a part that has been updated on newer versions  
of the same machine.  
Indicated by:  
“S/N XXXXX AND BELOW”  
“S/N XXXX AND ABOVE”  
“S/N XXXX TO S/N XXX”  
specific Model number use — Indicates that the part  
is used only with the specific model number or model  
number variant listed. It can also be used to show a  
part is NOT used on a specific model or model number  
variant.  
NOTICE  
When ordering a part that has more than one item  
number listed, check the remarks column for help in  
determining the proper part to order.  
Indicated by:  
paRT nO. Column  
“XXXXX ONLY”  
“NOT USED ON XXXX”  
numbers used — Part numbers can be indicated by a  
number, a blank entry, or TBD.  
“Make/Obtain Locally” — Indicates that the part can  
be purchased at any hardware shop or made out of  
available items.Examples include battery cables, shims,  
and certain washers and nuts.  
TBD (To Be Determined) is generally used to show a  
part that has not been assigned a formal part number  
at the time of publication.  
A blank entry generally indicates that the item is not sold  
separately or is not sold by Multiquip. Other entries will  
be clarified in the “Remarks” Column.  
“not sold separately”— Indicates that an item cannot  
be purchased as a separate item and is either part of an  
assembly/kit that can be purchased, or is not available  
for sale through Multiquip.  
page 26 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED SpARE pARTS  
MVC88VTH/MVC88VTWH pLaTe COMpaCTORWiTH HOnda gX160uT2qMX2 gasOLine engine  
1 to 5 units  
qty.  
3 ...........070100332............V-BELT  
p/n  
description  
5............0650140480..........SPARK PLUG  
1............28462ZH8003.......ROPE, RECOIL STARTER  
5............17210ZE1517.......ELEMENT, AIR CLEANER  
1............17620Z4H020.......CAP, FUEL TANK  
1............17672Z4H000.......FUEL FILTER, FUEL TANK  
4............939010230............SHOCK ABSORBER  
NOTICE  
Part numbers on this Suggested Spare Parts list may  
supersede/replace the part numbers shown in the  
following parts lists.  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bODY ASSY.  
45  
43  
42  
A
45  
53  
51  
43  
57  
63  
60  
44  
52  
54  
59  
61  
41  
62  
35  
36  
38  
37  
34  
39  
32  
38  
39  
31  
33  
56  
31  
(EG)  
9
32  
57  
34  
55  
36  
58  
35  
10  
19  
11  
12  
18-4  
18-3  
18-1  
18-5  
8
18-2  
7
6
16  
15  
29  
26  
27  
24  
23  
6
20  
28  
18  
5
21  
22  
26  
27  
28  
7
13  
17  
2
14  
64  
65  
26  
27  
28  
4
3
25  
2
4
3
1
page 28 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bODY ASSY.  
nO.  
A
1
2
3
4
5
6
7
paRT nO.  
416910120  
416120141  
939010230  
020310080  
030210250  
416120390  
001221025  
030210250  
416454360  
912216015  
001220850  
030208200  
031108160  
416466520  
416466540  
031108160  
022710809  
959404350  
416910100  
paRT naMe  
HANDLE ASSY. .................................................1................INCLUDES ITEMS W/%  
qTy.  
ReMaRks  
VIBRATING PLATE  
SHOCK ABSORBER  
NUT M10  
1
4
4
4
1
4
4
1
1
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
5
5
1
2
2
2
2
2
2
1
4
4
1
WASHER, LOCK M10  
BASE  
BOLT 10X25  
WASHER, LOCK M10  
RUBBER PLATE 25X25X8  
ENGINE ASSY.,GX160UT2QMX2  
BOLT 8X50  
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
WASHER, LOCK M8  
WASHER, FLAT M8  
ENGINE NUT  
ENGINE NUT  
WASHER, FLAT M8  
NYLON NUT M8  
EARTH WIRE, 1"  
CLUTCH ASSY  
18-1 416464490  
18-2 416351320  
18-3 080200300  
18-4 080600550  
18-5 042006006  
CLUTCH DRUM, 1"  
CLUTCH SHOE AND BOSS ASSY.  
STOP RING, S30  
STOP RING, AR55  
BEARING 6006  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
31  
32  
33  
34  
35  
36  
37  
38  
39  
90745ZE1600  
416452809  
952400130  
009110004  
070100332  
416120950  
416010040  
001220825  
030208200  
031108160  
001220820  
952408710  
404433430  
416452360  
952405600  
001221253  
030212300  
416121050  
0105091025  
030210250  
KEY 4.78X4.78X38  
COLLAR  
WASHER  
SOCKET HEAD BOLT 5/16"  
VBELT RPF3330  
BELT COVER, INNER  
BELT COVER, OUTER  
BOLT 8X25  
WASHER, LOCK M8  
WASHER, FLAT M8  
BOLT 8X20  
COLLAR 13X20X44  
RUBBER 20X32X28  
HANDLE STOPPER  
WASHER 12.5X35X4.5  
BOLT 12X65  
WASHER, LOCK M12  
GUARD HOOK  
BOLT 10X25  
WASHER, LOCK M10  
VAS HANDLE BODY  
41% 416121010  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bODY ASSY. (CONTINUED)  
45  
43  
42  
A
45  
53  
51  
43  
57  
63  
60  
44  
52  
54  
59  
61  
41  
62  
35  
36  
38  
37  
34  
39  
32  
38  
39  
31  
33  
56  
31  
(EG)  
9
32  
57  
34  
55  
36  
58  
35  
10  
19  
11  
12  
18-4  
18-3  
18-1  
18-5  
8
18-2  
7
6
16  
15  
29  
26  
27  
24  
23  
6
20  
28  
18  
5
21  
22  
26  
27  
28  
7
13  
17  
2
14  
64  
65  
26  
27  
28  
4
3
25  
2
4
3
1
page 30 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bODY ASSY. (CONTINUED)  
nO.  
paRT nO.  
paRT naMe  
qTy.  
1
2
2
2
1
2
2
2
1
1
2
1
1
1
1
1
ReMaRks  
42% 416218770  
43% 416459320  
44% 416459340  
45% 009120407  
GRIP, VAS HANDLE  
HANDLE NUT, VAS HANDLE  
RUBBER, VAS HANDLE  
SUNK HEAD BOLT 10X20  
TACH/HOUR METER  
BOLT 5X10  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
955010311  
001220510  
030205130  
58151  
WASHER, LOCK M5  
WASHER, FLAT M5  
RUBBER TUBE  
CURL CORD  
CLAMP  
CLIP BELT  
WASHER, FLAT M6  
BOLT 6X15  
WASHER, LOCK M6  
NUT M6  
959026822  
955010310  
507010110  
955010307  
952404470  
0105050616  
030206150  
020106050  
2067550101  
001221215  
031112230  
CLAMP COMPLETE  
BOLT 12X15  
WASHER, FLAT M12  
1
1
1
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIbRATOR ASSY.  
9
6
11  
10  
7
3
13  
8
12  
14  
16  
15  
10  
11  
9
4
5
1
2
4
page 32 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIbRATOR ASSY.  
nO.  
1
2
3
4
5
6
7
8
paRT nO.  
953405270  
953405260  
416218390  
040406211  
416338909  
416338919  
416349930  
060203030  
050101000  
014208020  
030208200  
416464470  
951405240  
952404250  
0105091025  
030210250  
paRT naMe  
PLUG 1/4X14 X13L  
PACKING 1/4"  
ECCENTRIC ROTATOR  
BEARING 6211  
CASE COVER (R)  
CASE COVER (L)  
BELT COVER GUARD  
OIL SEAL  
O-RING  
BOLT 8X20  
WASHER, LOCK M8  
PULLEY, VIBRATOR ASSY.  
KEY 7X7X19  
qTy.  
1
1
1
2
1
1
1
1
2
8
8
1
1
1
1
1
ReMaRks  
9
10  
11  
12  
13  
14  
15  
16  
WASHER 11X40X4  
BOLT 10X25  
WASHER, LOCK M10  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRANSpORT WHEEL ASSY.  
61  
59  
70  
58  
62  
61  
55  
20  
63  
57  
56  
71  
72  
21  
22  
51  
31  
32  
50  
31  
32  
41  
48  
42  
33  
47  
45  
52  
53  
43  
44  
37  
39  
38  
34  
36  
36  
36  
35  
page 34 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRANSpORT WHEEL ASSY.  
nO.  
20  
21  
22  
31  
32  
33  
34  
35  
36  
37  
38  
39  
41  
42  
43  
44  
45  
47  
48  
50  
51  
52  
53  
55  
56  
57  
58  
59  
61  
62  
63  
70  
71  
72  
paRT nO.  
0105050616  
030206150  
020106050  
012010030  
030210250  
416466680  
416352490  
012210035  
031110160  
032110180  
020310080  
020310080  
416218830  
959301000  
952400130  
020108060  
030208200  
939010270  
020108060  
416467230  
011206020  
030206150  
020106050  
416351700  
416466690  
458450880  
416467240  
025403016  
952408960  
952408980  
419466670  
011606025  
030206150  
020106050  
paRT naMe  
BOLT 6X15  
WASHER, LOCK M6  
NUT M6  
BOLT 10X30  
WASHER, LOCK M10  
SPACER, WHEEL  
BRACKET, WHEEL  
BOLT 10X35  
WASHER, FLAT M10  
CONICAL LOCK WASHER  
NUT M10  
qTy.  
1
1
1
4
4
1
1
2
6
4
2
2
1
2
2
2
2
1
1
1
2
2
2
1
1
1
1
1
2
1
1
1
1
1
ReMaRks  
NUT M10  
AXLE, TRANSPORT WHEEL  
WHEEL  
SPACER  
NUT M8  
WASHER, LOCK M8  
STOPPER RUBBER  
NUT M8  
STOPPER, LOCK PIN  
BOLT 6X20  
WASHER, LOCK M6  
NUT M6  
LOCK BRACKET, WHEEL  
LOCK PIN, WHEEL  
SPRING  
LOCK KNOB, WHEEL  
SPRING PIN 3X16  
WASHER, FLAT 6.5X16X1  
COLLAR 6.2X9X4  
LOCK WIRE, HANDLE  
BOLT 6X25  
WASHER, LOCK M6  
NUT M6  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SpRINKLER ASSY.  
11  
12  
10  
A
12  
13  
2
1
3
8
7
5
9
7
4
6
page 36 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SpRINKLER ASSY.  
nO.  
A
1
2
3
4
5
6
7
paRT nO.  
416910110  
033910050  
953406390  
954403241  
416338930  
416338940  
416452750  
001220825  
0401450080  
416452790  
paRT naMe  
WATER TANK W/CAP........................................1 ...............INCLUDES ITEMS W/%  
qTy.  
ReMaRks  
WASHER 14.5X30X1.6  
PACKING 13X28X2  
COCK PT 1/4"  
1
1
1
1
1
1
2
1
1
1
1
2
1
SPRINKLING PIPE  
PIPE HOLDER (L)  
PIPE HOLDER (R)  
BOLT 8X25  
8
9
WASHER, FLAT M8  
STAY, PIPE HOLDER  
CAP, WATER TANK  
BOLT 10X30  
10% 954300342  
11% 001241030  
12% 033910160  
13% 022910270  
WASHER, FLAT M10  
NUT M10  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
URETHANE pLATE ASSY.  
1
2
3
6
4
7
5
page 38 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
URETHANE pLATE ASSY.  
nO.  
1
2
3
4
5
6
7
paRT nO.  
416352080  
001221230  
012012030  
416352090  
011208035  
022710809  
PADUPA88  
paRT naMe  
HANGER, URETHANE PLATE  
BOLT 12X30  
WASHER, LOCK M12  
PLATE, URETHANE PLATE  
BOLT 8X35  
qTy.  
ReMaRks  
1
2
2
1
4
4
NYLON NUT M8  
PAD, URETHANE ..............................................1................REPLACES 416342390  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NAMEpLATE AND DECALS ASSY.  
B
1
19  
18  
14  
3
4
16  
11  
A
20  
21  
15  
2
C
17  
A
C
B
page 40 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NAMEpLATE AND DECALS ASSY.  
nO.  
1
2
3
4
11  
11  
14  
15  
16  
17  
18  
19  
20  
21  
paRT nO.  
920218170  
920900090  
920101410  
920105070  
920217430  
920217440  
920210330  
920208350  
920203290  
920203060  
920206290  
920201580  
920214100  
920212320  
paRT naMe  
DECAL, POSITION  
qTy.  
ReMaRks  
1
DECAL, SET/MVC/EXP, EU .............................1................ SET ONLY  
DECAL, MIKASA MARK 120X60  
DECAL, MIKASA MARK 125MM  
PLATE, SERIAL NO./88VTH  
PLATE, SERIAL NO./88VTHW  
DECAL, EC NOISE REQ.LWA105  
DECAL, V-BELT RPF3330  
DECAL, CAUTION  
1
1
1
1
1
1
1
1
1
1
1
1
DECAL, CAUTION  
DECAL, CAUTION (MANUAL/EXP)  
DECAL, MQ MARK 71X55  
DECAL ,E/G FIRE WARNING  
DECAL, FUEL CAUTION  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CYLINDER HEAD ASSY.  
15  
12  
12  
5
14  
3
2
7
1
6
4
10  
14  
13  
11  
13  
14  
14  
11  
10  
8
10  
page 42 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CYLINDER HEAD ASSY.  
nO.  
1%  
2%  
3
paRT nO.  
paRT naMe  
GUIDE, INLET VALVE (O.S.)  
GUIDE, EXHAUST VALVE (O. S.)......................1................INCLUDES ITEMS W/$  
HEAD COMP, CYLINDER..................................1................INCLUDES ITEMS W/%  
qTy.  
ReMaRks  
12204ZE1306  
12205ZE1315  
12210Z4M405  
1
4$% 12216ZE5300  
CLIP, VALVE GUIDE  
GASKET, CYLINDER HEAD  
COVER CP, HEAD  
PACKING, HEAD COVER  
TUBE, BREATHER  
FLANGE BOLT 6X12  
STUD BOLT 6X112  
STUD BOLT 8X32  
KNOCK PIN 10X16  
BOLT, FLANGE 8X60  
SPARK PLUG, EY45V  
1
1
1
1
1
4
2
2
2
4
1
5
6
7
8
10  
11  
12  
13  
14  
15  
12251ZL0003  
12310Z4M000  
12391ZE1000  
15721ZH8000  
90013883000  
90043ZE1020  
90047ZE1000  
9430110160  
957010806000  
0650140480  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CYL. bARREL ASSY.  
15  
3
4
6
6
7
19  
12  
16  
19  
17  
21  
4
5
17  
18  
9
13  
11  
8
14  
11  
9
1
page 44 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CYL. bARREL ASSY.  
nO.  
1
3
4%  
5%  
6%  
7
paRT nO.  
paRT naMe  
BARREL, ASSY CYLINDER (OIL ALERT)........1................INCLUDES ITEMS W/$  
GOVERNOR ASSY............................................1................INCLUDES ITEMS W/%  
qTy.  
ReMaRks  
12000Z4M406  
16510Z4M000  
16511Z4M000  
16512Z4M000  
16513ZE1000  
16531Z4M000  
16541Z4M000  
90131ZE1000  
90601ZE1000  
90602ZE1000  
91001ZF1003  
91201Z0T801  
91353671004  
9405010000  
WEIGHT, GOVERNOR  
HOLDER, GOVERNOR WEIGHT  
PIN, GOVERNOR WEIGHT  
SLIDER, GOVERNOR  
SHAFT, GOVERNOR ARM  
BOLT, DRAIN PLUG  
WASHER, DRAIN PLUG  
CLIP, GOVERNOR HOLDER  
BALL BEARING 6205  
OIL SEAL 25X41X6  
O-RING 14MM  
FLANGE NUT M10  
WASHER, PLAIN 6MM  
LOCK PIN 8MM  
FLANGE BOLT 6X12  
SWITCH ASSY., OIL LEVEL  
2
1
2
1
1
2
2
1
1
1
1
1
2
1
2
1
8
9
11  
12  
13$  
14$  
15  
16  
17  
18  
19  
21  
9410106800  
9425108000  
957010601200  
35480Z0T003  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CRANKCASE COVER ASSY.  
9
9
4
9
6
9
9
3
8
8
7
2
10  
11  
5
page 46 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CRANKCASE COVER ASSY.  
nO.  
2
3
4
5
6$  
7#  
8
9
10#  
paRT nO.  
paRT naMe  
COVER, ASSY. CRANKCASE...........................1................INCLUDES ITEMS W/#  
GASKET CRANKCASE  
CAP ASSY. OIL FILLER ....................................1................INCLUDES ITEMS W/$  
CAP ASSY. OIL FILLER.....................................1................INCLUDES ITEMS W/%  
qTy.  
ReMaRks  
11300Z4M640  
11381ZH8801  
15600Z0T810  
15600Z0T820  
15625Z0T800  
91201Z0T801  
9430108140  
1
PACKING, OIL FILLER CAP  
OIL SEAL 25X41X6  
KNOCK PIN 8X14  
FLANGE BOLT 8X32  
BALL BEARING 6205  
PACKING, OIL FILLER CAP  
1
1
2
6
1
1
957010803200  
961006205000  
11% 15625Z0T800  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CRANKSHAfT ASSY.  
8
1
page 48 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CRANKSHAfT ASSY.  
nO.  
1
8
paRT nO.  
13310Z4M800  
90745ZE1600  
paRT naMe  
CRANK SHAFT COMPLETE  
KEY 4.78X4.78X38  
qTy.  
ReMaRks  
1
1
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — pISTON ASSY.  
4
5
1
6
2
5
3
6
page 50 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — pISTON ASSY.  
nO.  
1
2
3
4
paRT nO.  
paRT naMe  
RING SET, PISTON (STD)  
PISTON (STD)  
PIN, PISTON  
ROD AY, CONNECTING....................................2................INCLUDES ITEMS W$  
BOLT, CONNECTING ROD 6X34.5  
CLIP, PISTON PIN 18MM  
qTy.  
ReMaRks  
13010Z4M801  
13101Z4M800  
13111Z4M000  
13200Z4M000  
90001Z4M000  
90551ZE1000  
1
1
1
5$  
6
2
2
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CAMSHAfT ASSY.  
2
9
12  
11  
10  
10  
7
8
5
3
1
4
15  
4
6
16  
5
3
15  
14  
6
16  
page 52 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CAMSHAfT ASSY.  
nO.  
1
2
3
4
5
6
7$  
8
9
10  
11  
12  
14  
15  
16  
paRT nO.  
paRT naMe  
SEAL, VALVE STEM  
qTy.  
ReMaRks  
12209Z4M801  
14100Z4M000  
14410Z4M000  
14431ZE1000  
14441ZE1010  
14451ZE1013  
14568ZE1000  
14711Z4M000  
14721Z4M000  
14751ZF1000  
14771ZE1000  
14773ZE1000  
14791Z4M000  
90012ZE0010  
90206ZE1000  
1
CAMSHAFT ASSY.............................................1................INCLUDES ITEM W/$  
ROD CP, PUSH  
ARM, VALVE ROCKER  
VALVE LIFTER  
PIVOT, ROCKER ARM  
SPRING, WEIGHT RETURN  
VALVE, INTAKE  
VALVE, EXHAUST  
SPRING, VALVE  
RETAINER, INTAKE VALVE  
RETAINER, EXHAUST VALVE  
PLATE, PUSH ROD GUIDE  
BOLT, PIVOT, 8MM  
2
2
2
2
1
1
1
2
1
1
1
2
2
NUT, PIVOT ADJUSTING  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — RECOIL STARTER ASSY.  
1
12  
4
3
5
9
7
8
6
2
16  
9
15  
4
11  
13  
page 54 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — RECOIL STARTER ASSY.  
nO.  
1
paRT nO.  
28400Z4M305ZD STARTER ASSY., RECOIL ................................1................INCLUDES ITEMS W/$  
paRT naMe  
qTy.  
ReMaRks  
2$  
3$  
4$  
5$  
6$  
7$  
8$  
9$  
11$  
12$  
13  
15$  
16$  
28410Z4M003ZD CASE CP, STARTER  
1
1
2
1
1
1
1
2
1
1
3
1
1
28421Z0T003  
28422ZH8801  
28431ZH8801  
28433ZH8801  
28441ZH8801  
28442ZH8003  
28443ZH8801  
28462ZH8003  
90003ZH8801  
90008ZE2003  
28461Z4M305  
28463Z4M003  
REEL, RECOIL STARTER  
RATCHET, STARTER  
PLATE, FRICTION  
RATCHET GUIDE  
FRICTION SPRING  
SPRING, RECOIL STARTER  
SPRING, RETURN  
ROPE, RECOIL STARTER  
SET SCREW  
BOLT, FLANGE 6X10  
KNOB, RECOIL STARTER  
KNOB, REINFORCEMENT  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — fAN COVER ASSY.  
18  
10  
17  
4
12  
16  
8
15  
15  
15  
15  
1
page 56 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — fAN COVER ASSY.  
nO.  
1
4
paRT nO.  
paRT naMe  
qTy.  
ReMaRks  
19610Z4M000ZB  
19611Z4M810  
19630Z4M000  
34150ZH7013  
35120Z0T851  
90013883000  
90022888010  
90601ZH7013  
957010600800  
COVER COMPLETE  
PLATE CP, SIDE (OIL ALERT)  
SHROUD COMPLETE  
ALERT, UNIT, OIL  
1
1
1
1
1
6
1
1
1
8
10  
12  
15  
16  
17  
18  
SWITCH AY, E/G STOP  
FLANGE BOLT 6X12  
FLANGE BOLT 6X20  
CLIP, HARNESS  
FLANGE BOLT 6X8  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CARbURETOR ASSY.  
18  
25  
15  
30  
1
21  
20  
22  
1
26  
14  
23  
11  
43  
9
17  
1
13  
24  
6
12  
29  
10  
2
16  
3
1
4
1
1
7
8
page 58 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CARbURETOR ASSY.  
nO.  
1#@+&^ 16010ZE1812  
paRT nO.  
paRT naMe  
GASKET SET  
FLOAT VALVE SET  
FLOAT SET  
CHAMBER SET, FLOAT................................1 ...........INCLUDES ITEMS W/+  
SCREW SET, PILOT  
SCREW SET, DRAIN ....................................1 ...........INCLUDES ITEMS W/^  
SCREW SET .................................................1 ...........INCLUDES ITEMS W/&  
CHOKE SET  
CARBURETOR ASSY....................................1............INCLUDES ITEMS W/#  
SCREW, THROTTLE STOP  
NOZZLE, MAIN  
PACKING, CUP  
INSULATOR, CARBURETOR  
PACKING, INSULATOR  
SPACER COMP., CARBURETOR  
PACKING, CARBURETOR  
qTy.  
ReMaRks  
1
1
1
2#  
3#  
4#  
6#  
7#+  
8#  
9#  
10  
11#  
12#  
13#  
14  
15  
16#  
17  
16011ZE0005  
16013Z0SB01  
16015Z4M911  
16016ZH7W01  
16024Z5T901  
16028Z5T901  
16044Z4M911  
16100Z4M911  
16124ZE0005  
16166Z4M911  
16173001004  
16211Z4M000  
16212ZH8800  
16220ZE1020  
16221ZH8801  
16610ZE1000  
16953ZE1812  
16954ZE1812  
16956ZE1811  
16957ZE1812  
16967ZE0811  
93500030060H  
9430520122  
1
1
1
1
1
1
1
1
1
18  
CHOKE LEVER COMP..................................1 ...........INCLUDES ITEMS W/%  
LEVER, COCK  
20#  
21#  
22#  
23#  
24#  
25#  
26%  
29#  
30#  
43#  
1
1
1
1
1
2
1
1
PLATE, LEVER SETTING  
SPRING, COCK LEVER  
PACKING, FUEL COCK  
CUP, FUEL STRAINER  
SCREW 3X6  
SPRING PIN 2X12  
MAIN JET #70  
99101ZH80700  
99204ZE00350  
16959Z5T901  
PILOT JET SET 835......................................1 ...........INCLUDES ITEMS W/@  
FILTER, CUP  
1
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — AIR CLEANER ASSY.  
13  
4
1
12  
2
10  
5
8
3
9
6
7
7
11  
11  
page 60 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — AIR CLEANER ASSY.  
nO.  
1
2
3#  
4
5#  
6
7%  
8%  
9
10  
11  
12  
13  
paRT nO.  
paRT naMe  
PACKING, ELBOW  
qTy.  
ReMaRks  
16271ZE1000  
17210ZE1517  
17218ZE1507  
17231Z4M010  
17232891000  
17235Z4M830  
17238ZE7010  
17239ZE1000  
17410Z4M000  
90325044000  
9405006000  
1
CLEANER ELEMENT........................................1................INCLUDES ITEMS W/#  
OUTER ELEMENT  
1
1
1
1
2
1
COVER, AIR CLEANER  
GROMET, AIR CLEANER  
NOSE, SILENCER  
COLLAR, AIR CLEANER  
COLLAR (B), AIR CLEANER  
ELBOW CP, AIR CLEANER...............................1................INCLUDES ITEMS W/%  
NUT, TOOL BOX SETTING  
FLANGE NUT 6MM  
1
2
1
1
957010602000  
90300Z1V000  
FLANGE BOLT 6X20  
NUT, AIR CLEANER  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — MUffLER ASSY.  
14  
14  
3
6
12  
14  
11  
15  
14  
12  
21  
7
9
13  
19  
page 62 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — MUffLER ASSY.  
nO.  
3
6
7
9
11  
12  
13  
14  
15  
19  
21  
paRT nO.  
paRT naMe  
PROTECTOR CP, MUFFLER (STD)  
DEFLECTOR CP  
ARRESTER, SPARK  
GASKET, MUFFLER  
GUIDE, MUFFLER  
SCREW, TAPPING, 4X8  
FLANGE BOLT 6X13  
TAPPING SCREW 5X8  
TAPPING SCREW 4X6  
NUT 8MM  
qTy.  
ReMaRks  
18320Z4M000  
18340ZE1010  
18355ZE1000  
18381Z0T801  
18522ZE1000  
90002Z0T800  
90016ZE1000  
90050ZE1000  
90055ZE1000  
94001080000S  
18310Z4M810  
1
1
1
1
1
2
1
4
1
2
1
MUFFLER COMPLETE  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — fUEL TANK ASSY.  
15  
16  
17  
16  
17  
13  
5
14  
7
8
9
2
10  
1
12  
12  
page 64 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — fUEL TANK ASSY.  
nO.  
1
2
5%  
7
8
paRT nO.  
paRT naMe  
qTy.  
ReMaRks  
16854ZH8000  
16955ZE1010  
17631Z0T801  
90004ZH7003  
91353671004  
9405006000  
RUBBER, SUPPORT (107MM)  
JOINT, FUEL TANK  
PACKING, FUEL FILLER CAP  
FLANGE BOLT 6X29  
O-RING 14MM  
1
1
1
1
1
2
1
2
9
FLANGE NUT 6MM  
TUBE, FUEL 4.5X145  
CLAMP, TUBE (D8)  
CAP COMP. , FUEL FILLER .............................1................INCLUDES ITEM W/%  
FILTER, FUEL  
10  
12  
13  
14  
15  
16  
17  
91424Z4M003  
950024080008  
17620Z4H020  
17672Z4H000  
17510Z4M000ZB TANK COMPLETE, FUEL NH1  
90503898000  
91302Z4M003  
1
1
2
2
WASHER, TANK CUSHION  
O-RING 5.5X1. 5  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — fLYWHEEL ASSY.  
5
2
1
9
4
page 66 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — fLYWHEEL ASSY.  
nO.  
1
2
4
5
paRT nO.  
paRT naMe  
WOODRUFF KEY 25X18  
COOLING FAN  
STARTER PULLEY  
FLYWHEEL COMPLETE  
NUT, SPECIAL 14MM  
qTy.  
ReMaRks  
13331357000  
19511ZE1000  
28451ZH8801  
31110Z4M000  
90201Z0T800  
1
1
1
1
1
9
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — IGNITION COIL ASSY.  
2
9
1
12  
12  
page 68 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — IGNITION COIL ASSY.  
nO.  
1
2
9
12  
paRT nO.  
paRT naMe  
qTy.  
ReMaRks  
30500Z0T802  
30700Z0T811  
36101ZE1010  
90121952000  
COIL ASSY, IGNITION  
CAP ASSY, NOISE SUPPRESSOR  
CORD, STOP SWITCH 370MM  
FLANGE BOLT 6X25  
1
1
1
2
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CONTROL ASSY.  
30  
22  
5
3
8
9
24  
13  
12  
18  
26  
7
19  
25  
11  
21  
21  
15  
27  
14  
28  
17  
16  
page 70 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — CONTROL ASSY.  
nO.  
3
5
7
8
paRT nO.  
paRT naMe  
CONTROL ASSY................................................1................INCLUDES ITEMS W/#  
qTy.  
ReMaRks  
16500Z4M306  
16551Z4M000  
16555Z4M000  
16561Z4M010  
16562Z4M000  
16571Z4M000  
16574ZE1000  
16575ZH8000  
16576891000  
16578ZE1000  
16580Z4M810  
16584883300  
16592ZE1810  
16594883010  
90013883000  
90015ZE5010  
90114SA0000  
90605230000  
93500040060H  
93500050160A  
93500050250H  
9405006000  
ARM, GOVERNOR  
ROD, GOVERNOR  
SPRING GOVERNOR  
SPRING, THROTTLE RETURN  
LEVER, CONTROL  
LEVER SPRING  
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
9
11#  
12#  
13#  
14#  
15#  
16#  
17#  
18#  
19#  
21  
22#  
24#  
25#  
26#  
27#  
28#  
30  
WASHER, CONTROL LEVER  
HOLDER, CABLE  
SPACER, CONTROL LEVER  
BASE CP, CONTROL  
ADJUSTING SPRING  
SPRING, CABLE, RETURN  
HOLDER, WIRE  
FLANGE BOLT 6X12  
BOLT, GOVERNOR ARM  
LOCK NUT 6MM  
CIR CLIP  
SCREW 4X6  
SCREW 5X16  
SCREW 5X25  
FLANGE NUT 6MM  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — DECALS  
13  
12  
4
5
3
15  
16  
14  
17  
18  
19  
page 72 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX160UT2QMX2 ENGINE — DECALS  
nO.  
3
4
paRT nO.  
paRT naMe  
EMBLEM (GX160)  
MARK, CHOKE  
MARK, THROTTLE INDICATION  
MARK, OP CAUTION (ENGLISH)  
MARK, EX. CAUTION (ENGLISH)  
MARK, OP CAUTION (FR)  
MARK, OP CAUTION  
MARK. EX. CAUTION (PICTOGRAP)  
MARK, EX. CAUTION (FR)  
WRENCH, SPARK PLUG  
HANDLE, BOX WRENCH  
qTy.  
ReMaRks  
87521Z4M000  
87528Z4M000  
87532ZH7000  
87516Z4H010  
87539Z4M000  
87516Z4H801  
87519Z4H000  
87539Z4M800  
87539Z4M810  
89216Z0T800  
89219805000  
1
1
1
1
1
1
1
1
1
1
1
5
12  
13  
14  
15  
16  
17  
18  
19  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TERMS AND CONDITIONS Of SALE — pARTS  
5. Parts must be in new and resalable  
condition, in the original Multiquip  
package (if any), and with Multiquip part  
numbers clearly marked.  
Multiquip reserves the right to quote and  
sell direct to Government agencies, and to  
Original Equipment Manufacturer accounts  
who use our products as integral parts of their  
own products.  
payMenT TeRMs  
Terms of payment for parts are net 30 days.  
FReigHT pOLiCy  
6. The following items are not returnable:  
All parts orders will be shipped collect or  
prepaid with the charges added to the invoice.  
All shipments are F.O.B. point of origin.  
Multiquip’s responsibility ceases when a  
signed manifest has been obtained from the  
carrier, and any claim for shortage or damage  
must be settled between the consignee and  
the carrier.  
a. Obsolete parts. (If an item is in the  
price book and shows as being  
replaced by another item, it is  
obsolete.)  
speCiaL eXpediTing seRViCe  
A $35.00 surcharge will be added to the  
invoice for special handling including bus  
shipments, insured parcel post or in cases  
where Multiquip must personally deliver the  
parts to the carrier.  
b. Any parts with a limited shelf life  
(such as gaskets, seals, “O” rings,  
and other rubber parts) that were  
purchased more than six months  
prior to the return date.  
LiMiTaTiOns OF seLLeR’s LiabiLiTy  
MiniMuM ORdeR  
Multiquip shall not be liable hereunder for  
damages in excess of the purchase price of  
the item with respect to which damages are  
claimed, and in no event shall Multiquip be  
liable for loss of profit or good will or for any  
other special, consequential or incidental  
damages.  
The minimum charge for orders from Multiquip  
is $15.00 net. Customers will be asked for  
instructions regarding handling of orders not  
meeting this requirement.  
c. Any line item with an extended  
dealer net price of less than  
$5.00.  
d. Special order items.  
ReTuRned gOOds pOLiCy  
Return shipments will be accepted and  
credit will be allowed, subject to the following  
provisions:  
e. Electrical components.  
f. Paint, chemicals, and lubricants.  
g. Decals and paper products.  
h. Items purchased in kits.  
LiMiTaTiOn OF WaRRanTies  
No warranties, express or implied, are  
made in connection with the sale of parts or  
trade accessories nor as to any engine not  
manufactured by Multiquip. Such warranties  
made in connection with the sale of new,  
complete units are made exclusively by a  
statement of warranty packaged with such  
units, and Multiquip neither assumes nor  
authorizes any person to assume for it  
any other obligation or liability whatever in  
connection with the sale of its products. Apart  
from such written statement of warranty,  
there are no warranties, express, implied or  
statutory, which extend beyond the description  
of the products on the face hereof.  
1. A Returned Material Authorization  
must be approved by Multiquip prior to  
shipment.  
7. The sender will be notified of any material  
received that is not acceptable.  
8. Such material will be held for five  
working days from notification, pending  
instructions. If a reply is not received  
within five days, the material will be  
returned to the sender at his expense.  
2. To obtain a Return Material Authorization,  
a list must be provided to Multiquip  
Parts Sales that defines item numbers,  
quantities, and descriptions of the items  
to be returned.  
9. Credit on returned parts will be issued  
at dealer net price at time of the original  
purchase, less a 15% restocking  
charge.  
a. The parts numbers and descriptions  
must match the current parts price  
list.  
b. The list must be typed or computer  
generated.  
10. In cases where an item is accepted, for  
which the original purchase document  
can not be determined, the price will be  
based on the list price that was effective  
twelve months prior to the RMA date.  
c. The list must state the reason(s)  
for the return.  
Effective: February 22, 2006  
d. The list must reference the sales  
order(s) or invoice(s) under  
which the items were originally  
purchased.  
11. Credit issued will be applied to future  
purchases only.  
pRiCing and RebaTes  
e. The list must include the name  
and phone number of the person  
requesting the RMA.  
Prices are subject to change without prior  
notice. Price changes are effective on a  
specific date and all orders received on or  
after that date will be billed at the revised price.  
Rebates for price declines and added charges  
for price increases will not be made for stock  
on hand at the time of any price change.  
3. AcopyoftheReturnMaterialAuthorization  
must accompany the return shipment.  
4. Freight is at the sender’s expense. All  
parts must be returned freight prepaid to  
Multiquip’s designated receiving point.  
page 74 — MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
MVC88VTH/VTHW pLaTe COMpaCTOR • OpeRaTiOn and paRTs ManuaL — ReV. #2 (12/09/13) — page 75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OperatiOn and parts Manual  
HERE’S HOW TO GET HELP  
PLEASE HAVE THE MODEL AND SERIAL  
NUMBER ON-HAND WHEN CALLING  
United StateS  
Multiquip Corporate Office  
MQ Parts Department  
18910 Wilmington Ave.  
Carson, CA 90746  
Contact: [email protected]  
Tel. (800) 421-1244  
Fax (310) 537-3927  
800-427-1244  
310-537-3700  
Fax: 800-672-7877  
Fax: 310-637-3284  
Service Department  
Warranty Department  
800-421-1244  
310-537-3700  
Fax: 310-537-4259  
Fax: 310-943-2238  
800-421-1244  
310-537-3700  
Fax: 310-943-2249  
Technical Assistance  
800-478-1244  
United Kingdom  
Canada  
Multiquip  
Multiquip (UK) Limited Head Office  
4110 Industriel Boul.  
Laval, Quebec, Canada H7L 6V3  
Contact: [email protected]  
Tel: (450) 625-2244  
Tel: (877) 963-4411  
Fax: (450) 625-8664  
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223  
Fax: 0161 339 3226  
Globe Lane,  
Dukinfield, Cheshire SK16 4UJ  
Contact: [email protected]  
© COPYRIGHT 2013, MULTIQUIP INC.  
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks  
are the property of their respective owners and used with permission.  
This manual MUsT accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.  
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in  
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published  
in this publication at any time without notice and without incurring any obligations.  
Your Local Dealer is:  
Download from Www.Somanuals.com. All Manuals Search And Download.  

MSi Computer Hardware K7N2 User Manual
Nilfisk ALTO Vacuum Cleaner IP32 7EA User Manual
Nilfisk ALTO Vacuum Cleaner SW 655 User Manual
Nintendo Video Games 70277A User Manual
NuTone Landscape Lighting 758NT User Manual
NuTone Pet Fence WF37 User Manual
Omron Thermostat V022 E3 1 User Manual
Palsonic VCR VCR2120 User Manual
Panasonic Car Stereo System CQ DFX972U User Manual
Panasonic Flat Panel Television 40RV525R User Manual