INSTALLATION AND OPERATION
MANUAL
EPA CERTIFIED
WOOD BURNING
STOVE
P
RETAIN THESE
INSTRUCTIONS
FOR FUTURE
REFERENCE
MODEL 1500HT
THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. READ
ENTIRE MANUAL THOROUGHLY BEFORE INSTALLATION.
P/N 775001M, Rev. Q, 12/03
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
CONGRATULATIONS ON THE PURCHASE OF
YOUR NEW WOODSTOVE MANUFACTURED BY
LENNOX HEARTH PRODUCTS.
Important Warnings ................................................ 2
Testing/Listing, EPA, Using this Manual.................. 3
Planning Your Installation..................................... 4-6
Manufactured (Mobile) Home Requirements ...........6
Installation .......................................................... 7-12
Product Features and Controls ..............................13
Care and Operation .......................................... 13-14
Recommended Fuel ...............................................15
Maintenance ..................................................... 15-17
Troubleshooting................................................ 18-19
Specifications..........................................................20
Replacement Parts List..................................... 21-22
Optional Accessories..............................................23
Safety/Listing Label.................................................24
EPA Label...............................................................25
Ownership Records ...............................................26
When you purchased your new woodstove, you
joined the ranks of thousands of concerned indi-
viduals whose answer to their home heating needs
reflects their concern for aesthetics, efficiency and
our environment. We extend our continued support
to help you achieve the maximum benefit and en-
joyment available from your new wood stove.
It is our goal at Lennox Hearth Products to provide
you, our valued customer, with an appliance that
will ensure you years of trouble-free warmth and
pleasure.
Thank you for selecting a Lennox Hearth Products
stove as the answer to your home heating needs.
Sincerely,
All of us at Lennox Hearth Products
PACKAGING LIST
This appliance is packaged with an accessory package,
which contains the following:
One - Installation and operation instructions manual
One - Warranty
Five - Baffle bricks
One - Marble set (for stove top and ash lip)
One - Insulation pad and strips. Place pad under top
marble and strips under ash lip marble.
TESTING/LISTING
Model 1500HT has been tested to UL Standards 1482
and ULC-S627 OMNI Test Laboratories Inc, Beaverton,
Oregon, Report #030-S-03-2.
USING THIS MANUAL
Please read and carefully follow all of the instructions
found in this manual. Please pay special attention to the
safety instructions provided in this manual. The Home-
owner’s Care and Operation Instructions included here
will assure you have many years of dependable and
enjoyable service from your appliance.
EPA CERTIFICATION
This heater has been tested to rigorous emissions stan-
dard, and has been certified by the Environmental Pro-
tection Agency.
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
PLANNING YOUR INSTALLATION
QUESTIONS TO ASK LOCAL BUILDING OFFICIAL
A correct installation is critical and imperative for reduc-
ing fire hazards and perilous conditions that can arise
when wood burning appliances are improperly installed.
The installer must follow all of the manufacturers’ in-
structions.
SELECTING A LOCATION
The design of your home and where you place your
stove will determine its value as a source of heat. A
wood stove depends primarily on air circulation (con-
vection) to disperse its heat, and therefore, a central
location is often best. There are other practical consid-
erations, which must be considered before a final selec-
tion of locations is made.
The installation of a wood burning appliance must con-
form to local codes and applicable state and federal
requirements. Familiarity with these requirements be-
fore installation is essential. Important considerations to
discuss with local building officials include:
♦
♦
♦
♦
♦
♦
♦
Existing Chimneys
Wood Storage
1. Applicable codes (i.e. Uniform Mechanical Code,
State or Regional Codes)?
Aesthetic Considerations
Roof Design (Rafter Locations & Roof Pitch)
Room Traffic
Electrical codes: Optional Blower Assemblies have
a flexible electrical cord that must be electrically
grounded per local codes or per electrical codes:
Proximity to Combustibles
Electrical Wiring
The installation of this stove will require some research.
Once your options are determined, consult with your
local building department who will be able to give you
the necessary installation requirements for your area (Is
a building permit required, Rooms where installation
may not be allowed, etc.).
In USA, NEC, ANSI/NFPA 70-1987
In Canada, CSA C22.1
WARNING: ELECTRICAL GROUNDING
INSTRUCTIONS: THIS APPLIANCE IS
EQUIPPED WITH
A
THREE-PRONG
(GROUNDING) PLUG FOR YOUR PRO-
TECTION AGAINST SHOCK HAZARD
AND SHOULD BE PLUGGED DIRECTLY
INTO A PROPERLY GROUNDED THREE-
PRONG RECEPTACLE. DO NOT CUT OR
REMOVE THE GROUNDING PRONG
FROM THIS PLUG.
WARNING: CHECK ALL LOCAL BUILDING AND
SAFETY CODES BEFORE INSTALLATION. THE IN-
STALLATION INSTRUCTIONS AND APPROPRIATE
CODE REQUIREMENTS MUST BE FOLLOWED EX-
ACTLY AND WITHOUT COMPROMISE. ALTERA-
TIONS TO THE STOVE ARE NOT ALLOWED. DO
NOT CONNECT THE STOVE TO A CHIMNEY SYS-
TEM SERVING ANOTHER STOVE, APPLIANCE, OR
ANY AIR DISTRIBUTION DUCT. FAILURE TO FOL-
LOW THESE INSTRUCTIONS WILL VOID THE
MANUFACTURERS WARRANTY.
2. Local amendments?
3. Is a permit required - cost?
(You may wish to contact your insurance company
to ask if they require this).
4. Is outside combustion air required?
5. Rooms where the installation is not allowed?
If you plan to vent your stove into an existing masonry
chimney, have it inspected by a local fire marshal or
qualified installer. Remember that a stove's perform-
ance is heavily influenced by the chimney and its loca-
tion on the roof. An oversized flue may not provide ef-
fective draw, and a flue liner may be required (see Draft
Requirements, page 10). Consult your dealer or quali-
fied installer before final selection is made.
SMOKE DETECTORS
Since there are always several potential sources of fire
in any home, we recommend installing smoke detec-
tors. If possible, install the smoke detector in a hallway
adjacent to the room (to reduce the possibility of occa-
sional false activation from the heat produced by the
stove). If your local code requires a smoke detector be
installed within the same room, you must follow the re-
quirements of your local code. Check with your local
building department for requirements in your area.
This stove requires pre-installation work to be com-
pleted before installation can take place. This will in-
clude the preparation of the floor and appropriate
hearth pad for acceptance of outside air (if applicable),
and for modification for flue and chimney.
NOTE – This appliance is NOT approved for installa-
tion into a Manufactured (Mobile) Home in Canada.
PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
PLANNING YOUR INSTALLATION
*ALCOVE CLEARANCE
COMBUSTIBLE WALL CLEARANCE
Required pipe: Type L-Vent pipe to top of stove. Ap-
proved brands are Dura-Vent, Pro-Vent, Ameri-I-Tek,
Standex, and Metal Bestos.
WARNING: IT IS VERY IMPORTANT THAT YOU
OBSERVE THE MINIMUM CLEARANCES.
There are listed clearances for your stove which were
determined in a Laboratory test using various "classes"
of stove pipe or chimney. Minimums are first estab-
lished for the stove itself and increased based on how
much heat is transferred by each class of pipe.
Alcoves must have minimum dimensions of 84" (213
cm) height minimum, 46" (117 cm) width minimum and
24" (610 mm) depth maximum.
Note: Manufactured (mobile) home installations require
the use of a Type L Vent Chimney connector only. Use
of a single wall flue pipe connection is not permitted.
Residential Reduced Clearance
Using Listed L Vent pipe (double wall air insulated) to
the top of the stove.
Approved brands are: Jakes-Evans, Dura-Vent, Secu-
rity, Pro-Vent, Ameri-Tek, Metal Bestos.
Alcove Clearances:
Back wall to pipe O.D.
Side wall to pipe O.D.
Back wall to stove
10 1/2" (267 mm) Minimum
20" (508 mm) Minimum
8" (203 mm) Minimum
Clearances (inches / millimeters)
A. 10 ½ / 267
B. 20 / 508
C. 15 / 381
D. 8 / 203
E. 9 ½ / 241
F. 5 / 127
Side wall to stove
9 1/2" (241 mm) Minimum
Residential Standard (not approved for manufac-
tured [mobile] homes)
Using single wall pipe connector to the top of the stove.
*NOTE: Alcove dimensions cannot be reduced by the use of
non-combustible materials such as brick, stone, etc. Alcove
dimensions listed are minimum dimensions and are not
measurements for building an Alcove. You will need to con-
sider these clearances, as well as other dimensional re-
quirements before you build the alcove and install this appli-
ance.
Clearances (inches / millimeters)
A. 15 / 381
B. 19 / 483
C. 15 / 381
D. 13 / 330
E. 8 ½ / 216
F. 5 / 127
Manufactured (Mobile) Home Standard Clearance
Using Approved L Vent only. Approved brands are
Dura-Vent, Security, Pro-Vent, and Ameri-Tek. Manu-
factured (mobile) Home installations must use a rain
cap with a spark arrestor.
PROTECTED WALL CLEARANCE when the stove is in-
stalled adjacent to a protected wall system. The variance must
be approved by your local building official. Normally, the pro-
tected wall system is defined as a non- combustible material
with a minimum of 1" air space behind. Check your local build-
ing codes or with a qualified installer (Ref. NFPA 211).
Clearances (inches / millimeters)
A. 10 ½ / 267
B. 20 / 508
C. 15 / 381
D. 8 / 203
E. 9 ½ / 241
F. 5 / 127
OPTIONAL ARCH TREATMENT
An alcove depth of 24" (610 mm) (or less) will allow for a
minimum height of 84" (213 cm) and may be trimmed with a 2
1/4" (57 mm) maximum arch treatment if desired.
CORNER
INSTALLATION
PARALLEL
INSTALLATION
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
PLANNING YOUR INSTALLATION
OUTSIDE AIR
REDUCED MASONRY STRUCTURE CLEARANCE
(ALCOVE)
In all manufactured (mo-
bile) homes and in many
site built residences (sub-
ject to local code), a stove
may be required to use
outside air for combustion.
A 5 ¼” (133 mm) square
outside air floor duct is
available through your
dealer.
Your Earth Stove can be installed in a masonry struc-
ture with reduced clearances if the structure was built to
National Building Code for fireplaces and chimneys
(UBC 37).
The firebox of the masonry structure must be of ade-
quate size to allow a minimum of 6" (152 mm) clear-
ance to the sides and top of the stove and 2" (51 mm)
clearance to the rear. All stove models must be installed
on their original listed legs or base unless otherwise
specified by OMNI Testing Laboratory.
This stove can take in outside air directly through the base.
This type installation requires a hole through the floor pro-
tector and the use of outside air floor duct (catalog #
14M67) to penetrate into the air space below the home.
FLOOR PROTECTION
This appliance requires a non-combustible floor protec-
tion for ember protection. If the floor protection is to be
stone, tile, brick, etc., it must be mortared or grouted to
form a continuous non-combustible surface. If a chim-
ney connector extends horizontally over the floor, pro-
tection must cover the floor under the connector and at
least 2" (51 mm) to either side.
NOTE: Because the base sits 1" (25.4 mm) off the
floor, the outside air floor duct can be positioned along
the front to rear center line under the pedestal, but as
close to the opening in the base as location permits.
The outside air floor duct opening must be protected
from any possible obstruction including loose floor insu-
lation.
The floor protection must extend completely beneath the
stove and to the front, sides, and rear as indicated:
USA REQUIREMENTS
16” minimum to the front of the fuel door glass
8" minimum beyond the sides of the fuel door opening
0” minimum to the back of the stove body
MANUFACTURED (MOBILE) HOME REQUIREMENTS
This stove is certified as a Room Heater, Solid Fuel Type
and may be used in Manufactured Housing providing the
following requirements are followed:
CANADA REQUIREMENTS
18” (457 mm) min. to the front of the fuel door glass
8” (203 mm) min. beyond the sides of the stove body
8” (203 mm) min. to the back of the stove body
• An outside air inlet must be provided for combustion and
be unrestricted while unit is in use.
STANDARD PARALLEL HEARTH PAD SHOWN
• WARNING: DO NOT INSTALL IN SLEEPING ROOM.
• Regulations require that the appliance must be secured
to the floor and grounded to the chassis. See Securing
the Stove to the Floor (and) Grounding Stove, page 7.
• Required venting is 6” (152 mm) diameter Type L-Vent
connector pipe with listed factory-built 103HT chimney
suitable for use with solid fuels or a code approved ma-
sonry chimney. Approved brands of factory built chimney
are listed in this manual. Rain cap and spark arrestors are
required (see Clearances, page 5).
0” - USA
8” – Can.
8” (203 mm)
Canada
8” (203 mm)
Canada
8” (203 mm)
USA
8” (203 mm)
USA
18” (457 mm) – Canada
16” (406 mm) - USA
REMOVE ASH DRAWER CLIP
• CAUTION: THE STRUCTURAL INTEGRITY OF THE
MOBILE HOME FLOOR, WALL, AND CEILING/ROOF
MUST BE MAINTAINED.
The ash drawer is secured for shipping with a small
retaining screw at the top of drawer. Remove and dis-
card this screw.
• The chimney must provide for a section joint so that any
parts extending above 13' 6" (412 cm) from ground level
can be removed for transportation of the manufactured
(mobile) dwelling.
VENTILATION
(Residential homes which do not require an outside
air inlet). Ventilation is essential when using a solid fuel
stove. The combustion process uses oxygen from in-
side the home and it may be necessary to open a win-
dow or install a vent to provide combustion air in a
house that is well insulated.
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SECURING THE STOVE TO THE FLOOR
Manufactured (Mobile) Homes Only
INSTALLING MARBLE ACCENTS
Marble is a natural product and therefore each piece
will have its own unique character. Marble can be
scratched so care should be taken to avoid putting
heavy or rough objects (trivet/steamers) on the surface.
If the marble should become scratched, the scratch
may be removed or diminished by polishing it with jew-
elers rouge (which can be purchased at many hardware
stores). Do not install the marble before curing the
paint.
Once the outside air floor duct is in position, replace the
floor protector. Make sure that the floor protector's hole
is aligned with the outside air opening. Next position
and align the stove on the hearth pad. Manufactured
(mobile) home installations require that the stove be
secured to the floor. This ensures that the stove will not
shift when the manufactured (mobile) home is moved.
To do this, mark where the holes are to be drilled using
a marking instrument long enough and small enough to
fit through the (4) four holes in the stove base. Mark
holes, then remove the stove. Drill the (4) four holes,
with a 1/4" (7 mm) drill bit. Drill down through the floor
protector and the manufactured (mobile) home floor.
Use 1/4" (7 mm) lag bolts and secure to the manufac-
tured (mobile) home floor.
The marble set consists of 2 pieces. A large piece
which fits onto the stove top and a smaller piece which
fits onto the ashlip which is located below the fuel door.
Install the marble gasket and marble as follows:
1. Install gasket on stove top as shown in the illustra-
tion. The ceramic fiber blanket and strips (cerawool)
NOTE: If the composition of the manufactured (mobile)
home floor is of light particleboard construction, you will
be required to secure the stove with regular hex head
bolts and nuts. This will ensure that the bolts will not rip
out of the floor when the manufactured (mobile) home is
being moved.
which
come
with each unit
must be placed
under the mar-
ble to insulate it
from the high
temperatures
GROUNDING STOVE
on top of the
Manufactured (Mobile) Homes Only
Regulations require that all stoves installed in manufac-
firebox. Do not
place the mar-
tured (mobile) homes must be grounded. To do this
simply attach a piece of No. 8 copper wire, at least 18"
(457 mm) in length from the stove to the chassis of the
manufactured (mobile) home.
ble directly on
the top metal surface of the stove or it will crack.
2. Place top marble piece onto the gasket on stove
top
3. Place ashlip marble into recessed area on the stove
ashlip (located below the fuel door).
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSTALLING THE BAFFLE BRICKS
TYPES OF CHIMNEYS
There are 2 brick retainer tube assemblies located be-
low the ceiling of the firebox which require baffle brick
before the stove can be operated. Install the baffle brick
as follows:
1. Place the first three brick onto the brick retainers
with the notch facing up and toward the front. Next,
slide the three brick all the way to the right (as you
face the stove. See top view illustration below).
2. Place the fourth brick on top of the three brick. Posi-
tion it so the notch is facing up and pointing to the
left.
The chimney is a vital part of your stove installation. A
properly built masonry chimney or a properly installed
factory built chimney will assure a consistent draft under
a variety of weather conditions (a smoking stove is usu-
ally caused by a chimney problem). The stove flue size
is 6 inches (152 mm) diameter, which is approximately
28 square inches (711 square mm) minimum. The
maximum flue size should be no more than (3)-three
times the cross sectional area of the size of the stove
flue collar. In this case, that would be no larger than a
10 inch (254 mm) diameter stack, or approximately 85
square inches (216 square cm) maximum.
3. Install the fifth brick and slide all the way to the left.
4. Rotate the fourth brick into position (notch to the
front and facing up) until it drops into place.
All chimneys must be installed as specified by local
building codes and according to the chimney manufac-
turer instructions (in the case of a factory built chimney).
See the chimney manufacturer instructions for exact
specifications. Factory built chimneys must comply with
UL 103HT or ULC S629.
IMPORTANT: The baffle brick requires periodic in-
spection and replacement for proper operation. If
the baffle bricks are fractured or crumbling, they
should be replaced. Do not operate this appliance
without the baffle brick properly installed.
TOP VIEW OF BAFFLE BRICK
SIDE VIEW OF BAFFLE BRICK
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
CHIMNEY INSPECTION
ACCEPTABLE CONNECTOR PIPE FOR INSTALLA-
TIONS
Existing chimneys must be inspected before installing
your stove. Consult your local building department for
chimney code requirements. A masonry chimney must
have a code approved liner. This liner must not have
broken or missing pieces. Some non-code masonry
chimneys may be brought up to code by being relined.
(Consult your dealer or qualified chimney sweep). Fac-
tory built chimneys should also be inspected, first for
creosote deposits (which should be removed), and then
for integrity of the stainless steel liner. Look for obvious
bulges in the lining which may indicate the need to re-
place that section (use a bright flashlight). Also, inspect
the attic to see that the chimney has proper clearance
to combustible framing members. For interior masonry
chimneys and most factory built chimneys, this must be
a (2) two inch (51 mm) air space clearance, which must
not be filled with insulation or any other material. An
exterior masonry chimney must have a (1) one inch
(25.4 mm) air space clearance.
For Standard Residential Clearances: Six 6 inch (152
mm) minimum, single wall, 25 gage minimum thickness,
stove pipe is acceptable. Three (3) pre-drilled holes are
provided in the flue collar for fastening the pipe securely
to the stove. Use sheet metal screws to do this. Addi-
tional sections of single wall pipe should be fastened
together with at least three (3) sheet metal screws each
section. When connecting to the factory built ceiling
support package, use the manufacturer's transition
piece, usually called a dripless connector, to join single
wall pipe to their factory built chimney section.
Minimum Flue Size: The required minimum diameter
and area required for the flue size is (respectively) 6
inches / 152 mm diameter, which is approximately 28
square inches / 711 square mm. The maximum flue
size should be no more than (3) three times the cross
sectional area of the size of the 6 inches / 152 mm di-
ameter flue collar. In this case, that would be no larger
than a 10 inch (254 mm) diameter (area = approx. 85
sq. inches [216 sq. cm]).
Vapor Barrier At Chimney Penetration
Install all venting components per the Vent Manufactur-
ers installation instructions. Ensure that there is an ef-
fective vapor barrier at the location where the chimney
penetrates to the exterior of the structure. This can be
accomplished by applying a non-hardening waterproof
sealant to the following components:
•
Around the chimney at the point where the storm
collar will meet the chimney just above the Flash-
ing.
Connection To A Factory Built Chimney: This space
heater is to be connected to a factory-built chimney
conforming to CAN / ULC – S629, Standard for 650°C
Factory-Built Chimneys.
•
Along the vertical seam of the chimney pipe, where
it is exposed to the weather.
•
•
On each nail head on the flashing.
Around the chimney at the point where the storm
collar will meet the chimney just above the flashing.
Notes:
For Reduced Residential Clearances: Type L and
listed double wall connector pipe is acceptable. Install
any factory built brand of pipe according to the manu-
facturer's instructions.
•
On a flat or tarred and graveled roofs, nail and seal
the flat roof flashing to the roof on all sides with
roofing compound.
•
Do not put screws through the flashing into the
chimney pipe.
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
DRAFT REQUIREMENTS
CHIMNEY HEIGHT REQUIREMENTS
The chimney must extend 3 feet (914 mm) above the
level of roof penetration and a minimum of 2 feet (610
mm) higher than any roof surface within 10 feet (305
cm) (see below). Check with your local building officials
for any additional requirements for your area.
The appliance is merely one component of a larger sys-
tem. The other equally important component is the vent-
ing system. This is necessary for achieving the required
flow of combustion air to the fire chamber and for safely
removing unwanted combustion byproducts from the
appliance. If the venting system's design does not pro-
mote these ends, the system may not function properly.
Poorly functioning venting systems may create per-
formance problems as well as be a safety hazard (i.e.
an oversized chimney may result in less than optimum
performance. Installations into a large, masonry chim-
ney may require a liner to improve performance). A
draft test should read greater than .04' W.C. (inches
water column) and less than .08" W.C.
Due to prevailing winds, local terrain, adjacent tall trees,
a hill, or ravine near the home, or adjacent structures,
additional chimney height or a special chimney cap may
be required to ensure optimum performance.
Top of the flue must be 3’ (915
mm) higher than highest point
of roof penetration
Requires a
listed termi-
nation cap
Top of the flue must be
2’ (610 mm) higher
than any part of roof
within 10’ (305 cm)
horizontal
These rules are minimums. In some
instances, chimney height may need to
be increased to achieve sufficient draft.
American National Standards Institute ANSI/NFPA 211-
92, draft 1-7: A chimney or vent shall be so designed
and constructed to develop a flow sufficient to com-
pletely remove all flue and vent gases to the outside
atmosphere. The venting system shall satisfy the draft
requirements of the connected appliance in accordance
with the manufacturers instructions.
To achieve a stable draft, the total flue height required
(from the appliance to termination) is 12 to 15 feet (366
to 457 cm) minimum.
For Manufactured (Mobile) Homes Only: Portions of
the chimney and termination that exceed an elevation of
13½ feet above ground level may be designed to be
removed for transporting the manufactured (mobile)
home.
PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
RESIDENTIAL STANDARD
MANUFACTURED (MOBILE) HOME STANDARD
Using 6” (152 mm) Diameter Single Wall Con-
nector Pipe Not Approved For Manufactured
(Mobile) Home
Using 6” (152 mm) Diameter Type L-Vent Connector Pipe
PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Combustible Wall Chimney Connector Pass-Throughs
A
Method A. 12 inch (305 mm) Clearance to Combustible Wall Mem-
ber: Using a minimum thickness 3.5 inch (90 mm) brick and a 5/8
inch (16 mm) minimum wall thickness clay liner, construct a wall
pass-through. The clay liner must conform to ASTM C315 (Stan-
dard Specification for Clay Fire Linings) or its equivalent. Keep a
minimum of 12 inches (305 mm) of brick masonry between the
clay liner and wall combustibles. The clay liner shall run from the
brick masonry outer surface to the inner surface of the chimney
flue liner but not past the inner surface. Firmly grout or cement
the clay liner in place to the chimney flue liner.
Method B. 9 inch (229 mm) Clearance to Combustible Wall Mem-
ber: Using a 6 inch (152 mm) inside diameter, listed, factory-built
Solid-Pak chimney section with insulation of 1 inch (25.4 mm) or
more, build a wall pass-through with a minimum 9 inch (229 mm)
air space between the outer wall of the chimney length and wall
combustibles. Use sheet metal supports fastened securely to wall
surfaces on all sides, to maintain the 9 inch (229 mm) air space.
When fastening supports to chimney length, do not penetrate the
chimney liner (the inside wall of the Solid-Pak chimney). The in-
ner end of the Solid-Pak chimney section shall be flush with the
inside of the masonry chimney flue, and sealed with a non-water
soluble refractory cement. Use this cement to also seal to the
brick masonry penetration.
B
Method C. 6 inch (152 mm) Clearance to Combustible Wall Mem-
ber: Starting with a minimum 24 gage (.024 inch [.61 mm]) 6-inch
metal chimney connector, and a minimum 24 gage ventilated wall
thimble which has two air channels of 1 inch (25.4 mm) each, con-
struct a wall pass-through. There shall be a minimum 6 inch (152
mm) separation area containing fiber glass insulation, from the
outer surface of the wall thimble to wall combustibles. Support the
wall thimble, and cover its opening with a 24-gage minimum sheet
metal support. Maintain the 6 inch (152 mm) space. There should
also be a support sized to fit and hold the metal chimney connec-
tor. See that the supports are fastened securely to wall surfaces
on all sides. Make sure fasteners used to secure the metal chim-
ney connector do not penetrate chimney flue liner.
C
Method D. 2 inch (51 mm) Clearance to Combustible Wall Mem-
ber: Start with a solid-pak listed factory built chimney section at
least 12 inches (305 mm) long, with insulation of 1 inch (25.4mm)
or more, and an inside diameter of 8 inches (2 inches [51 mm]
larger than the 6 inch [152 mm] chimney connector). Use this as a
pass-through for a minimum 24-gage single wall steel chimney
connector. Keep solid-pak section concentric with and spaced 1
inch (25.4 mm) off the chimney connector by way of sheet metal
support plates at both ends of chimney section. Cover opening
with and support chimney section on both sides with 24 gage
minimum sheet metal supports. See that the supports are fas-
tened securely to wall surfaces on all sides. Make sure fasteners
used to secure chimney section do not penetrate chimney flue
liner.
D
NOTES:
1. Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through the wall pass-through system
and the chimney wall, to but not past the inner flue liner face.
2. A chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or a floor, or ceiling.
3. Where passage through a wall, or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365.
PAGE 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT FEATURES AND CONTROLS
CARE AND OPERATI0N
ASH DRAWER
FUEL DOOR
The large ash drawer located on the left side of the ped-
estal is designed to make cleaning easier by containing
the ashes in a removable drawer.
CAUTION: WHEN OPENING THE DOOR, DO NOT EX-
TEND IT BEYOND ITS NORMAL TRAVEL. OVEREX-
TENDING THE DOOR TO A FURTHER OPEN POSITION
CAN PUT EXCESSIVE STRESS ON HINGE AREA OF
DOOR AND HINGE PINS AND MAY RESULT IN BREAK-
AGE.
CAUTION: DO NOT OPERATE THE STOVE WITH
THE ASH DRAWER OPEN OR AJAR, AS THIS WILL
PRODUCE EXTREME TEMPERATURES WITHIN THE
STOVE (OVERFIRING) AND COULD CAUSE DAMAGE
(SUCH DAMAGE IS NOT COVERED BY THE MANU-
FACTURERS' WARRANTY). REPLACE THE ASH
DRAWER GASKET IF IT BECOMES FRAYED OR
DAMAGED.
PRIMARY AIR CONTROL
The primary combustion air delivery is controlled by the
Primary Air Control Assembly (The control handle is lo-
cated below the fuel door). The heat output can be con-
trolled by sliding the handle to a higher or lower heat out-
put setting (See Care and Operation Section – Primary
Air Control, page 14). The fuel, the amount of heat and
burn times desired, the type of installation are all vari-
ables that will affect the control setting. The same control
settings in a variety of installations will produce different
results. You will need to try different settings so you can
learn how much heat to expect and how long the fire will
burn. The same control settings in a variety of installa-
tions will produce different results. You will need to try
different settings so you can learn how much heat to ex-
pect and how long the fire will burn.
DOOR OPERATION
The door handle assembly opens and securely latches
the fuel door closed (see illustration above). To open the
door, rotate the coil handle to the 9:00 position until door
releases. To close and latch, hold the coil handle in the
9:00 position, close the door, then rotate the handle to
the 6:00 position. See illustration above.
GLASS
The Glass is a super heat resistant ceramic that with-
stands continuous temperatures up to 1390°F. This tem-
perature is well beyond the temperatures in which you
operate your stove. If the glass ever becomes damaged
in any way, replace it, using only 5mm ceramic glass
(catalog # G2000-7).
This appliance is designed to provide a flow of air over
the inside of the glass, which along with high heat helps
keep it clean. When operating the stove on low for ex-
tended periods of time, the glass may get dirty. A short,
hot fire (15 - 20 minutes) will help clean off much of the
normal buildup (see troubleshooting). A commercial
glass cleaner designed for stoves is recommended for
cleaning.
The glass should be cleaned thoroughly with glass
cleaner and a soft cloth BEFORE the stove is burned.
PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND OPERATION
PRIMARY AIR CONTROL
After each 20-minute burn, allow the appliance to cool
completely. The third burn should be at least medium
high or about 450°F. for 45 - 60 minutes. The paint will
become soft and emit non-toxic haze during these
burns. Keep the area well ventilated.
This appliance is equipped with a control for the combustion
air, located on the lower right side (front) of the stove. Slid-
ing the control to the right increases the burn rate, to the left
decreases the burn rate.
As the paint cures it will become slightly lighter in
color. Eventually the entire surface will become an
even color. Once the paint has been softened and
cooled two or three times, it will harden. Do not turn
on a blower during the curing process. Do not place
anything on the stove surface until the paint is com-
pletely cured. Do not attempt to repaint the stove until
the paint is completely cured. If the surface later be-
comes stained or marred, it may be lightly sanded and
touched up with spray paint from the same paint (See
Maintenance Section, pages 15-17). Paint is available
at your local authorized Lennox Hearth Products
dealer. Never attempt to paint a hot stove.
You will generally want to set the control in the low or me-
dium range. The stove is safe burning on any setting as
long as combustibles are kept at the specified safe dis-
tances.
PROVIDE ADEQUATE AIR FOR COMBUSTION
In well insulated and weather tight homes, it may be difficult
to establish a good draft up your chimney. The poor draft is
caused by a shortage of air in the house. To provide the
needed air, crack a window on the windward side of the
house.
HOW TO START AND MAINTAIN A FIRE
1. OPEN the Primary Air Control by sliding it to the
right. This allows the firebox and fresh fuel to
quickly come up to ideal operating temperature.
2. Build your fire directly on the Firebrick covering
the bottom of the stove.
In some cases, you may want to duct air directly from the
outside to your firebox (See Outside Air, page 6), or to a
nearby floor or wall vent.
a. Place five or six loosely crumpled sheets of
newspaper in the stove.
b. Add a small amount of dry kindling randomly
on the top of the newspaper.
USE CONTROL SETTINGS THAT WORK FOR YOU
The fuel, the amount of heat you want, the type of installa-
tion you have and how long you wish the fire to burn are all
variables that will affect the control setting. The same con-
trol settings in a variety of installations will produce different
results.
c. Place a few more loosely crumpled newspa-
pers on top of the kindling and light the bottom
paper first, then light the top paper. Once the
fire is well underway, close the fuel door. The
upper fire should preheat the chimney and cre-
ate an effective draft while the lower fire ignites
the kindling.
Familiarize yourself with your stove by trying different set-
tings so you can learn how much heat to expect and how
long the fire will burn. It may take a week or two to learn but
your patience will be rewarded by the warmth and pleasant
satisfaction that only a wood fire can provide.
3. After the kindling is burning well, add increasingly
larger pieces of wood until the fire is actively burn-
ing.
4. When the fire is well-established slide the air con-
trol lever for the desired heat output.
BREAK-IN PERIOD
REFUELING
Your stove finish is a high temperature paint that requires
time and temperature to completely cure. We recommend
that you ventilate the house during the initial burns. The
paint emits non-toxic odors during this process.
To refuel the stove, first slide the air control to high.
Let the fire "liven up" for about one minute. Open the
fuel door about 1/2" (1 cm) and hold in this position for
30 seconds or until stove is drafting well. Open door
and add wood. If the fire or coal bed is almost de-
pleted and a full load of cord wood is added, it may be
necessary to leave the air control on the high setting
for a while to re-establish a lively fire. Once the wood
is burning at a brisk rate, slide the air control for the
desired heat output.
KEEP YOUR HOUSE WELL VENTILATED DURING THE
CURING PROCESS TO PREVENT ACTIVATION OF
YOUR HOME SMOKE DETECTOR.
The paint manufacturer recommends three burn cycles to
cure the paint. The first two burns should be low heat, ap-
proximately 250°F., for 20 minutes each, using paper and
light kindling.
PAGE 14
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL
WHY SEASONED WOOD?
BURN RECOMMENDED FUEL
The key to the success of a good fire that produces heat
from a woodstove is the wood. It needs to be well-
seasoned natural wood.
This appliance is approved for use with untreated natural
dry wood only (see Important Warnings, page 2, #8). Do
not burn particleboard scraps or pressed logs using bond-
ing agents because they can produce conditions that will
deteriorate metal. Green or uncured wood does not work
well as fuel, and can cause increased creosote buildups.
The value of green wood as a source of heat is limited. Do
not overload or use kindling wood or mill ends as primary
fuel as this may cause overfiring. Overfiring is a condition
where excessive temperatures are reached, beyond the
design capabilities of the stove. The damage that occurs
from overfiring is not covered under the stove warranty.
What does “Well-Seasoned” mean?
When a tree is cut down, the wood is green, full of sap
and moisture. This moisture content can exceed 80%,
which must be reduced to less than 20%. Wood properly
seasoned is then capable of generating the heat the
stove was designed to provide.
Green wood does not burn easily. Attempting to burn
green wood often results in a lot of smoke and very little
fire. Time is the most important factor in seasoning
wood. Ideally the moisture content should be reduced to
11-20%, although very few of us will be able to check
that figure. There are several steps that should be taken
to ensure that that you come close to these figures.
WARNING: BURNING IMPROPER FUEL (I.E. CHAR-
COAL) CAN RESULT IN CARBON MONOXIDE POISON-
ING WHICH MAY LEAD TO DEATH!
SEASONING GUIDE
Softwoods – 6 months to 18 months
Hardwoods – 12 months to 24 months
CARBON MONOXIDE POISONING – EARLY SIGNS OF
CARBON MONOXIDE POISONING RESEMBLE THE FLU
WITH HEADACHES, DIZZINESS, OR NAUSEA. IF YOU
HAVE THESE SIGNS, GET FRESH AIR AT ONCE! HAVE
THE HEATER INSPECTED BY A QUALIFIED SERVICE
TECHNICIAN. SOME PEOPLE ARE MORE AFFECTED
BY CARBON MONOXIDE THAN OTHERS. THESE IN-
CLUDE PREGNANT WOMEN, PEOPLE WITH HEART OR
LUNG DISEASE OR ANEMIA, THOSE UNDER THE IN-
FLUENCE OF ALCOHOL, AND THOSE AT HIGH ALTI-
TUDES.
Logs that are 5” (127 mm) diameter across or larger
should be split in half, three pieces if over 8 inches (203
mm), and four pieces when over a foot (305 mm)
across. If the tree fell 2 to 4 years ago, it still needs to be
cut, split, and seasoned for 6 to 24 months depending
on the wood.
WOOD STORAGE
Wood to be seasoned should be stacked in an area
open enough to ensure good air circulation on both
sides – leaving adequate space between woodpiles to
walk comfortable. Do not stack wood against a wall or
building. It helps to elevate the woodpiles off the ground
(two 2 x 4’s running lengthwise beneath the woodpile
works well). This allows air to flow under the bottom
logs.
Wood that is kept outdoors, either covered with a tarp, or
not covered at all, will not burn well until it has been in an
enclose space for one to two months.
PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SMALL AREA PAINT TOUCH-UP
DOOR, GLASS AND ASH DRAWER GASKETS
A 3/4" (19 mm) spun fiberglass rope gasket pro-
vides the seal around the fuel door and a 1/8” x 1”
(3 mm x 25.4 mm) flat woven gasket glass provides
the seal around the glass. And a 1/4" (6.4 mm)
spun fiberglass gasket provides a seal around the
ash drawer. Should these gaskets become frayed
or damaged they should be replaced with the same
size and type as the original gasket. Contact your
dealer for ordering. Use high temperature silicone
sealer as an adhesive for the door gasket. The
glass gasket and ash drawer gaskets have a self-
adhesive backing (see Replacement Parts List,
pages 21-22).
The stove body is painted with a quality high-temperature
stove paint. Use only model TSPK-B Stove Paint, Catalog #
70K99. Do not touch-up your stove with any other paint.
Using one small piece of 320 grit sand paper and lightly
sand the blemish so that the edges are “feathered” or
smooth to the touch between the painted and bare sur-
faces. Do not let the sand paper gum up with paint, as this
will cause scratches on the metal surface. If there are any
scratches, use 600 grit sandpaper instead. Mask off sur-
faces you do not want painted. Paint lightly over the bare
surface first as this will act as an undercoat. Then paint over
a larger area in smooth even strokes to blend.
See Break-In Period on page 14 for information on cur-
ing the paint.
WARNING: THE GASKETS MUST BE KEPT IN
GOOD CONDITION. DO NOT LEAVE THE STOVE
BURNING WITH THE DOOR OR ASH DRAWER
OPEN OR AJAR. THIS WILL CAUSE EXCESSIVE
HEAT BUILD UP IN THE UNIT AND COULD IG-
NITE SURROUNDING COMBUSTIBLES AS
WELL AS DAMAGE THE STOVE BY OVERFIR-
ING IT. OVERFIRING IS A CONDITION WHERE
EXCESSIVE TEMPERATURES ARE REACHED,
BEYOND THE DESIGN CAPABILITIES OF THE
STOVE (SUCH DAMAGE IS NOT COVERED BY
THE MANUFACTURERS WARRANTY).
FIREBRICK
The firebrick should be inspected periodically and replaced
if damaged (crumbling or excessively cracked).
ASH REMOVAL AND DISPOSAL
CAUTION: MAKE SURE THAT THE FIRE IS OUT AND
THE STOVE IS COLD BEFORE REMOVING ASHES!
NEVER BURN YOUR STOVE WITH THE ASH DRAWER
OPEN OR UNSECURED!
Ashes can hold live embers for several days, and must be
disposed of with care.
Scrape ashes from the firebox through the grate into the
ash drawer. After emptying, clean and replace the ash
drawer and tighten the securing knobs.
SERVICING GLASS
CAUTION: BE CAREFUL NOT TO ABUSE DOOR
ASSEMBLY BY STRIKING OR SLAMMING IT. IF
THE DOOR ASSEMBLY OR GLASS IS BROKEN
OR DAMAGED, THEY MUST BE REPLACED BE-
FORE HEATER CAN BE SAFELY OPERATED.
USE ONLY COMPONENTS PROVIDED BY THE
MANUFACTURER AS REPLACEMENT PARTS.
NEVER place ashes in a cardboard box or any other com-
bustible receptacle.
Proper Disposal of Ashes:
Ashes should be placed in a metal container with a tight
fitting lid. The closed container of ashes should be placed
on a noncombustible floor or on the ground, well away from
all combustible materials, pending final disposal. If the
ashes are disposed of by burial in soil or other wise locally
dispersed, they should be retained in the closed container
until all cinders have thoroughly cooled.
Cleaning Glass: Ensure stove is cold prior to
cleaning glass. A commercial glass cleaner de-
signed for stoves is recommended. Do not use
abrasive cleaners.
Note: The removable ash drawer holds approximately two
gallons of ashes.
PAGE 16
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Replacing Glass:
Burn Approved Fuel Only - This stove is approved
for burning dry seasoned natural wood only. Using
green or inadequately seasoned wood may in-
crease creosote buildup.
1. Remove door from stove by lifting door up and off hinge
pins: Place the door on a flat protected (towel) clean flat
surface with the inside of the door facing up. Remove the
glass clips (by removing screws holding clips), then care-
fully remove broken glass one piece at a time (protective
gloves are recommended).
2. Clean the area where the glass with gasket will be in-
stalled.
3. Install new glass with gasket (use only factory 5-mm
glass with glass channel gasket. Do not substitute).
Carefully reinstall glass clips. Be very careful not to over-
tighten screws.
Inspection Frequency - The chimney connector
and chimney should be inspected at least twice
monthly during the heating season to determine if a
creosote buildup has occurred. If creosote has ac-
cumulated it should be removed to reduce the risk
of a chimney fire.
Cleaning - Remove the brick baffle in the firebox
prior to having your chimney cleaned (should be
done by a qualified chimney sweep). See Installing
the Baffle Bricks on page 8 and reverse steps to
remove baffle brick).
4. Reinstall door.
CLEANING BLOWER INTAKE
If an optional blower kit (catalog #14M22) is installed, the
blower air intake requires cleaning at least once a year to
remove lint, dust, etc. If there are pets in the dwelling, the
intake should be cleaned at least twice a year.
In the event of a chimney fire - Make sure the fuel
door is securely closed. Adjust the primary air con-
trol to the lowest (most closed) setting. Call the fire
department immediately.
CREOSOTE FORMATION AND NEED FOR REMOVAL
What is Creosote - When wood is burned slowly, it pro-
duces tar and other organic vapors, which combine with
expelled moisture to form creosote. The creosote vapors
condense in the relatively cool chimney flue of a slow-
burning fire. As a result, creosote residue accumulates on
the flue lining. When ignited this creosote makes an ex-
tremely hot fire. Also, creosote deposits tend to form in long
runs of venting where gases become too cool prior to ex-
hausting. Note: Single wall pipe cools rapidly, therefore in-
stallations using this type of flue are more susceptible to
creosote deposits.
After a chimney fire, the complete chimney system
should be checked by a qualified technician before
further use.
Consult your dealer for suggestions on proper
chimney care. Contact your local municipal or pro-
vincial fire authority for information on how to han-
dle a chimney fire. Have a clearly understood plan
for handling a chimney fire.
To inhibit the build up of creosote, adjust the primary air
control to a medium-high or high setting for a 10-minute
period each day. Do not attempt to burn out heavy creo-
sote accumulations in this manner. This must be removed
from the chimney by scraping or brushing to reduce the risk
of a chimney fire.
REINSTALL BAFFLE BRICK
After your chimney has been swept, reinstall the
brick baffle (See Installing the Baffle Bricks on
page 8).
PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SMOKES OUT FUEL DOOR WHEN OPEN (see ✸)
1. The primary air control is closed.
BACKPUFFING (✸)
1. Downdraft in the chimney (a special wind cap may be
needed).
2. The chimney is too cool. Set the primary air control on
"HIGH" for a few minutes before opening the fuel door.
3. Excess creosote will not only restrict your draft but it will
create a risk of a creosote fire. Strictly adhere to mainte-
nance requirements as outlined in this manual. If excess
creosote has built up on the inside of the firebox sides and
door, burn a small hot fire at intervals that are more fre-
quent with air control on HIGH for a few minutes.
4. Deposits may have built up in the chimney and are restrict-
ing the draft, or the spark arrestor on top of the chimney
may be plugged.
2. The house is too air tight (ventilation is needed).
3. Insufficient vertical height to chimney to achieve ade-
quate draft.
ODORS
1. Creosote accumulation in firebox (brush out on next
cleaning).
2. Chimney downdraft when stove is not operating
(close the primary air control).
5. Chimney diameter too large or too small to provide ade-
quate draft.
3. Paint curing on first several burns.
6. The house is too airtight (usually takes 20 to 30 minutes for
problem to appear as stove lowers air pressure in house).
Crack a window open or provide an outside source of air
near stove.
7. Insufficient vertical height to chimney to achieve adequate
draft.
DIRTY GLASS (✸)
1. Poor draft conditions.
2. Long burn periods at low draft settings.
3. Burning wet, pitchy or spongy wood.
4. Poorly arranged logs (too close to glass).
DOES NOT PRODUCE ENOUGH HEAT (✸)
1. Using green or insufficiently cured wood.
2. Excessive draft.
3. High ceilings (heat rises quickly, but can be recirculated by
a well-placed ceiling fan with a winter/summer switch).
4. The area to heat is too large (square foot heating estimates
are based on "average" climates and home design).
5. There is an obstruction in the chimney. The chimney or
chimney cap is restricted by creosote preventing enough
draw to sustain a "high" heat output rate.
(✸) Draft problems; if installing into a larger flue, it
may be necessary to use a full length liner to
achieve adequate draft for the appliance. A draft
gauge should read a minimum of .05" w.c.
(inches water column) not to exceed .07" w.c.
for optimum performance (See Draft Require-
ments, page 10).
OVERFIRING DAMAGE
If the heater or chimney connector glows, you are over-
firing. Other symptoms may include: Cracking, warping
or burning out of components, stove glass may develop
a haze, which will not come off with cleaning.
DOES NOT MAINTAIN A FIRE (✸)
1. Soft wood does not burn as long or as well as seasoned
hardwood resulting in a short burn time.
2. Wood size too small. Burns at too rapid a rate.
3. The gasket seal on the fuel door, ash drawer or glass is
leaking air. Repair or replace it if necessary.
4. Excessive draft. There may be an obstruction in the chim-
ney.
Overfiring of a stove is a condition where excessive tem-
peratures are reached, beyond the design capabilities of
the appliance. The damage that occurs from overfiring is
not covered under the manufacturers limited warranty.
PAGE 18
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Do not operate this stove with the Air Control in the
"open" position (pulled out) for extended periods. This
wastes fuel and can cause dangerous overfiring condi-
tions. NEVER leave the stove unattended on high set-
tings.
The following are a few conditions that should be evaluated
and (corrected if necessary) if an overfiring condition is sus-
pected:
Overfiring Caused From Improper Installation - Ensure that
all installation requirements have been met as outlined in the
installation manual. The chimney should be clean and in good
repair. A draft test should be performed to determine if the
draft requirements of the appliance are being met. A draft
gauge should read between .05 and .07 inches water column
(" W.C.).
Overfiring Caused From Improper Maintenance -
Strictly adhere to all maintenance requirements at fre-
quent intervals as prescribed in this manual including
cleaning of flue and stove. Should the fuel door, ash
drawer or glass gaskets become worn or damaged, they
should be replaced.
Excessive draft (above .07 " W.C.) will allow too much com-
bustion air to be pulled in which results in hotter burns. Too
little draft (below .05 " W.C.) will not allow enough combustion
air delivery to maintain a fire (this may result in improper op-
eration of appliance, i.e. won't maintain fire unless fuel door is
left open. See Care and Operation Section).
Overfiring Caused From Improper Fuel - This appli-
ance is approved for use with natural dry well seasoned
wood only (ask your authorized dealer what are ap-
proved fuels for your area). Do not burn garbage, parti-
cleboard scraps, or pressed logs using bonding agents
because they can produce conditions that will deterio-
rate metal. Do not overload or use kindling wood or mill
ends as primary fuel as this may cause overfiring.
Overfiring Caused From Improper Operation - Operate this
appliance only as outlined in this manual. Never burn the ap-
pliance with the fuel door or ash drawer open or ajar.
PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS: Model 1500 HT
Approximate heating capacity
Up to ~1500 Sq. Ft.
(Up to ~450 Sq. M)
Outside air provision
Log length
Yes
20" (508 mm)
Top
Flue position
Flue collar size
Width
6" (152 mm)
27 1/2" (699 mm)
24" (610 mm)
30 3/4" (781 mm)
29 3/4" (756 mm)
5 3/4" (146 mm)
6 - 8 hours
Depth
Height (to flue)
Height
Stove back to flue center
Approx. burn time
Fuel capacity
Firebox Size
35 lbs. (16 kg)
1.85 cubic feet
(564 cubic mm)
Maximum Burn Rate (BTU)
EPA BTU Range
58,730
11,700-37,000
63%
EPA Efficiency
Emissions Rate (grams/hour)
Loading
6.6 gph
Front
Approx. weight with brick
345 lbs. (157 kg)
Blower (Optional)
W/ speed control
160 CFM, .9 amp,
Rheostat (75v - 110v)
Note: Dimensions shown are approximations only
(+/- ¼” [6.4 mm])
~ Square feet (square meter) heating capacity and burn time
are approximations only. They will vary depending upon
the level of insulation, climate, house design, ceiling
height, ambient outside temperatures and how the
stove is operated.
PAGE 20
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS LIST - Model 1500HT
PART NO. DESCRIPTION
Door Parts
G6000
14M72
27M67
86-128
27M81
G2000-7
10300
11529
11531
10362
Door Assembly, Cast Black
Door Assembly, Gold
Clip Set, Glass
Door Gasket Kit, 3/4" Rope (includes adhesive)
Gasket, Glass Channel (Per Foot)
Glass, Arched 9 1/2 X 15 3/4" (glass gasket not included)
Handle Assembly (fits gold & cast doors)
Hinge, Pin 10 L 18, Original, Top/Bottom (requires welding)
Hinge Pin (retrofit), Top Only (Requires Drilling, #3 [.213”] & Tap 1/4-28 UNF)
Torque Plate (latch)
Draft Module Parts
26M28
907
Module, Primary Air Draft
Module Coil Handle (brass)
Component Parts
1100
Ash Drawer Assembly
1135
Knob, Ash Drawer
27M80H
13009
Gasket, Ash Drawer (3/8" wide X 1/8" thick)
Trim, Top Louver
Fan System Parts (if optional kit(s) installed)
Dial - A - Temp (rheostat)
14440
Misc. Component Parts
1054
Cerawool Pad For Marble (requires 1)
Cerawool Strip For Marble (requires 4)
Marble Set, Gray (marble gasket, 1ea. 1054 & 4ea. 1051, is provided w/ appliance)
Marble Set, Green (marble gasket, 1ea. 1054 & 4ea. 1051, is provided w/ appliance)
Firebox Parts (see firebrick diagram, next page) note: all firebrick are 1 ¼” thick
Grate, Cast Iron
1051
MS1502
MS1505
1115
12009
Brick Retainer, 8"
For the location of the nearest Dealer for replacement parts, contact:
Lennox Hearth Products
1110 West Taft Avenue
Orange, CA 92865
PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT DIAGRAMS – Model 1500HT
FIREBRICK
Part/Catalog #
FB-1
Quantity
Dimensions
Part/Catalog #
FB11
Quantity
1
Dimensions
6
9 x 4 1/2”
4 1/2” x 4 3/8”
FB2
10
5
9 x 4 1/2” w/notch
* 9 x 4 1/2” w/notch
Grate
* Baffle brick are a special denser brick. Do not substi-
tute
10545
01115
FB-5
Note: All brick are 1 ¼” thick.
1
1
9 x 2 1/2” w/hole
DOOR ASSEMBLY
BRICK DIAGRAM
HANDLE ASSEMBLY
PRIMARY AIR DRAFT MODULE
PAGE 22
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL ACCESSORIES – Model 1500HT
Note: Install and use accessories per instructions provided with the accessory kit.
Blower Kit
Catalog # Model #
Description Notes
A Blower Kit (includes rheostat for variable speed control)
is available for increased heat circulation.
14M67
OAFD-S
Outside Air
Floor Duct
5 1/4" Square
14M72
14M22
DK100-G Gold Door Kit
Blower
BK-100
Blower Kit
Includes Dial-A-
Temp for Variable
Speed Control
14M21
70K99
SSK
Stove Stat Kit Thermally Controls
Blower
TSPK-B
Touch-up
Spray Paint
Kit, Black
12 oz Spray Can
Outside Air Floor Duct
(Duct penetration measures 5 ¼” square)
Variable Speed Control, Dial-A-Temp
Stove-Stat Kit
Gold Door Kit
PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY/LISTING LABEL
PAGE 24
Download from Www.Somanuals.com. All Manuals Search And Download.
EPA LABEL
PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNERSHIP RECORDS
Dealer’s Name:
Dealer’s Address:
City:
State:
Zip Code:
Serial Number:
Notes:
Date of Purchase:
Date Installed:
SERVICE AND MAINTENANCE LOG
Service Service
Date Technician
Service
Description
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
1110 West Taft Avenue
Orange, CA 92865
Download from Www.Somanuals.com. All Manuals Search And Download.
|