Milwaukee Car Stereo System 9560 User Manual

OPERATOR’S

MANUAL

ELECTRIC CHAIN HOIST

Catalog No.

Rated Load

9560

1/2 Ton

9561

9562

9565

9566

9567

9568

1 Ton

2 Ton

9570

9571

9572

9573

The equipment described and illustrated in these

instructions is intended for industrial use only and

should not be used to lift, support or otherwise

transport people.

Follow all instructions and warnings for

inspecting, maintaining and operating this hoist.

The use of any hoist presents some risk of personal injury

or property damage. That risk is greatly increased if proper

instructions and warnings are not followed. Before using this

hoist, each operator should become thoroughly familiar with

all warnings, instructions, and recommendations in this

manual. Retain this manual for future reference and use.

Forward this manual to the hoist operator.

Failure to operate the equipment as directed in the manual

may cause injury.

Before using the hoist, fill in the information below. Model and

serial numbers are stamped into the aluminum hoist housing.

Model Number

Serial Number

Purchase Date

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

20. NOT allow the load chain or hook to be touched by a live

welding electrode.

SAFETY PRECAUTIONS

21. NOT remove or obscure the warnings on the hoist.

22. NOT operate a hoist on which the safety placards or decals

Each MILWAUKEE Electric Chain Hoist is built in accordance with

the specifications contained herein and at the time of manufacture

complies with our interpretation of applicable sections of

*American Society of Mechanical Engineers Code (ASME)

B30.16 “Overhead Hoists,” the National Electrical Code

(ANSI/NFPA 70) and the Occupational Safety and Health Act

(OSHA). Since OSHA states the National Electrical Code applies

to all electric hoists, installers are required to provide current

overload protection and grounding on the branch circuit section in

keeping with the code. Check each installation for compliance with

the application, operation and maintenance sections of these

articles.

are missing or illegible.

23. NOT operate a hoist unless it has been securely attached to

a suitable support.

24. NOT operate a hoist unless load slings or other approved

single attachments are properly sized and seated in the hook

saddle.

25. Take up slack carefully - make sure load is balanced and load

holding action is secure before continuing.

26. Shut down a hoist that malfunctions or performs unusually

and report such malfunction.

27. Make sure hoist limit switches function properly.

28. Warn personnel of an approaching load.

*Copies of this standard can be obtained from ASME Order

Department, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300,

U.S.A.

Improper operation of a hoist can create a potentially

hazardous situation which, if not avoided, could result

in minor or moderate injury. To avoid such a potentially

hazardous situation, THE OPERATOR SHALL:

Improper operation of a hoist can create a potentially

hazardous situation which, if not avoided, could result

in death or serious injury. To avoid such a potentially

hazardous situation, THE OPERATOR SHALL:

1. Maintain firm footing or be otherwise secured when operating

the hoist.

1. NOT operate a damaged, malfunctioning or unusually

performing hoist.

2. Check brake function by tensioning the hoist prior to each

lift operation.

2. NOT operate the hoist until you have thoroughly read and

understood the manufacturer’s Operating and Maintenance

Instructions or Manuals.

3. Use hook latches. Latches are to retain slings, chains, etc.

under slack conditions only.

3. NOT operate a hoist which has been modified without the

manufacturer’s approval or without certification that it is in

conformity with ANSI/ASME B30 volumes.

4. Make sure the hook latches are closed and not supporting

any parts of the load.

5. Make sure the load is free to move and will clear all

obstructions.

4. NOT lift more than rated load for the hoist.

5. NOT use hoist with twisted, kinked, damaged, or worn load

chain.

6. Avoid swinging the load or hook.

7. Make sure hook travel is in the same direction as shown on

the controls.

6. NOT use the hoist to lift, support, or transport people.

7. NOT lift loads over people.

8. NOT operate a hoist unless all persons are and remain clear

of the supported load.

8. Inspect the hoist regularly, replace damaged or worn parts,

and keep appropriate records of maintenance.

9. Use MILWAUKEE recommended parts when repairing the

unit.

9. NOT operate unless load is centered under hoist.

10. NOT attempt to lengthen the load chain or repair damaged

10. Lubricate load chain per hoist manufacturer’s

recommendations.

load chain.

11. Protect the hoist’s load chain from weld splatter or other

damaging contaminants.

11. NOT use the hoist’s overload limiting clutch to measure load.

12. NOT use limit switches as routine operating stops. They are

12. NOT operate hoist when it is restricted from forming a

emergency devices only.

straight line from hook to hook in the direction of loading.

13. NOT allow your attention to be diverted from operating

13. NOT use load chain as a sling, or wrap chain around load.

14. NOT apply the load to the tip of the hook or to the hook latch.

the hoist.

14. NOT allow the hoist to be subjected to sharp contact with

15. NOT apply load unless load chain is properly seated in the

other hoists, structures, or objects through misuse.

chain sprocket(s).

15. NOT adjust or repair the hoist unless qualified to perform

16. NOT apply load if bearing prevents equal loading on all load

such adjustments or repairs.

supporting chains.

17. NOT operate beyond the limits of the load chain travel.

18. NOT leave load supported by the hoist unattended unless

specific precautions have been taken.

19. NOT allow the load chain or hook to be used as an electrical

or welding ground.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

TABLE OF CONTENTS

Safety Precautions......................................................................................................................................................................2

Hoist Specifications.....................................................................................................................................................................3

Application Information ...............................................................................................................................................................4

Safety Information.......................................................................................................................................................................4

Installation...................................................................................................................................................................................4

Operation ....................................................................................................................................................................................5

Maintenance ...............................................................................................................................................................................6

Wiring Diagrams .......................................................................................................................................................................12

Trouble Shooting .......................................................................................................................................................................13

Inspection and Maintenance Check List...................................................................................................................................14

Recommended Lubrication Schedule.......................................................................................................................................15

Replacement Parts List.............................................................................................................................................................16

Parts Depot & Warranty Repair Centers...................................................................................................................................28

Warranty .....................................................................................................................................................................Back Cover

HOIST SPECIFICATIONS

MILWAUKEE Electric Chain Hoists are rugged, portable hoists

that provide quick, precise lifting. The hoists are constructed of

tough, but lightweight, die cast aluminum alloy housings. An oil

bath transmission, equipped with heat-treated, alloy steel

gears and an overload limiting clutch, provides smooth and

reliable operation.

Other features that ensure the safe operation of MILWAUKEE

Electric Chain Hoists include a magnetic disc brake that

delivers sure stopping and secure holding of the load.

Adjustable upper and lower limit switches regulate the load

travel. As a standard, hooks are supplied with safety latches.

For additional safety, a chain stop is attached to the slack end

of the load chain.

With a pushbutton station that fits comfortably in one hand, the

operator can safely control the hoist while the other hand is

free to guide the load. The electrical controls, which are readily

accessed under the electrical cover, utilize quick connections

for easy voltage conversions and a 24V control circuit for

added safety.

MILWAUKEE Electric Chain Hoists are designed and tested in

accordance with the American Society of Mechanical

Engineers Code B30.16, “Safety Standard for Overhead

Hoists.” Hoists are built in compliance with CSA, file number

LR 44484. Made in U.S.A.

Table 1 - Hoist Specifications

Lifting

Speed

(fpm)

Control Cord

Length

(ft)

Full Load

Motor Amps*

Model

Capacity

(tons)

Lift

(ft)

Reeving

Voltage

(AC)

Phase

9560

9561

9562

9565

9567

9568

9566

9570

9572

9573

9571

1/2

Single-chained

1/2

115/230V

230/460V

115/230V

230/460V

7.6/3.8

14/7**

3.2/1.6

14/7**

3.2/1.6

Single

Three

Single

Three

Double-chained

* At full load, it is not unusual for the hoist to draw in excess of **The 1HP, 115/230V models must have a dedicated power

the values listed when lifting. It is critical to ensure that the

voltage at the hoist contactor does not drop below 10% of

the nominal voltage of the hoist while it is lifting a load. Low

voltage will result in higher amp draw, damage to the hoist,

and potential fire hazards. MILWAUKEE is not responsible

for any damages caused by an inadequate power source.

circuit rated for at least 20A, 125V when they are wired for

115V. It is not unusual for these models to draw up to 20

amps at 115V when lifting at rated capacity. Refer to

Table 3 before installation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

APPLICATION INFORMATION

Always disconnect the power source before working

on or near a hoist or its connected load. If the power

disconnect point is out of sight, lock it in the open

position and tag to prevent unexpected application

of power.

This hoist is intended for general industrial use for lifting and

transporting freely suspended material loads within its rated

capacity. MILWAUKEE cannot be responsible for applications

other than those for which MILWAUKEE equipment is

recommended. Prior to installation and operation, we caution

the user to review his application for abnormal environmental

or handling conditions and to observe the applicable

recommendations as follows:

4. Protect the power cable and control cable from coming in

contact with sharp objects.

5. Do not kink power cable and control cable and never allow

the cable to come in contact with oil, grease, hot surfaces,

or chemicals.

ADVERSE ENVIRONMENTAL CONDITIONS

6. Make certain that the power source conforms to the

requirements of your equipment.

Do not use the hoist in areas containing flammable vapors,

liquids, gases or any combustible dusts or fibers. Refer to

Article 500 of the National Electrical Code. Do not use this

hoist in highly corrosive, abrasive or wet environments. Do not

use this hoist in applications involving extended exposure to

ambient temperatures below -10°F or above 130°F.

7. Inspect the unit daily before operating hoist.

8. Cluttered areas and benches invite accidents.

9. The operator should not engage in any practice which will

divert his attention while operating the hoist.

10. Before using the hoist, the operator should be certain that

all personnel are clear.

LIFTING OF HAZARDOUS LOADS

This hoist is not recommended for use in lifting or transporting

hazardous loads or materials which could cause widespread

damage if dropped. The lifting of loads which could explode or

create chemical or radioactive contamination if dropped

requires fail-safe redundant supporting devices which are not

incorporated into this hoist.

11. Do not operate hoist with loads exceeding its rated capacity.

12. Supporting frames or beams used as a hoist hanger must

have a greater load capacity than the hoist.

13. Do not attempt to operate hoist beyond normal maximum

lift range.

14. Align hoist for a straight line pull. Avoid side pull or end pull.

15. Do not operate hoist with twisted or damaged chain.

LIFTING OF GUIDED LOADS

This hoist is not recommended for use in the lifting of guided

loads, including dumbwaiters and elevators. Such applications

require additional protective devices which are not

incorporated into this hoist. For such applications, refer to the

requirements of applicable state and local codes, and the

American National Safety Code for elevators, dumbwaiters,

escalators and moving walks (ASME A17.1).

16. Do not operate a damaged or malfunctioning hoist until

necessary adjustments or repairs have been made.

17. Do not use hoist to lift people or to carry loads over people.

18. Do not leave a load suspended in the air unattended.

19. Always remove load before making repairs.

20. Do not remove or obscure capacity or warning decals.

INSTALLATION

1. Before installing the hoist, check the following:

Failure to comply with Safety Precautions outlined

throughout this manual can result in serious injuries

or death. Before using this hoist, each operator

should become thoroughly familiar with all warnings,

instructions and recommendations in this manual.

a. Make sure all supporting structures and attaching devices

are strong enough to hold your intended loads. If in doubt,

consult a qualified structural engineer.

b. Provide proper branch circuit protection for the hoist as

recommended in the National Electrical Code.

SAFETY INFORMATION

1. Follow all local electrical and safety codes, as well as the

National Electrical Code (NEC) and the Occupational

Safety and Health Act (OSHA) in the United States.

c. The power supply should be within plus or minus 10% of

the voltage specified on the motor nameplate. It is critical

to use adequate sized power cables, especially with

1-phase hoists (See Table 3). Be sure dual voltage hoists

are connected or wired to correspond with your power

supply (See WIRING, page 9).

2. Hoist must be securely and adequately grounded. The hoist

power cable is provided with an additional lead (green) for

grounding purposes.

d. Installation area must provide operating conditions for the

operator including sufficient room for the operator and

other personnel to stand clear of the load at all times.

3. Be careful when touching the exterior of an operating

motor; it may be hot enough to be painful or cause injury.

With modern motors this condition is normal if operated at

rated load and voltage (modern motors are built to operate

at higher temperatures).

e. For installations where the slack chain hanging from the

unit may be objectionable or hazardous, the use of a

chain container is recommended. See INSTALLATION OF

CHAIN CONTAINER ASSEMBLY.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

2. Before operating the hoist, be sure to observe the following:

a. ALWAYS DISCONNECT HOIST FROM POWER SUPPLY

before removing the electrical cover or when making any

electrical connection in the hoist or pushbutton station.

b. The ground wire (green colored) of the power cable

should always be connected to a suitable ground by

means of a screw or clamp. An alligator clip does not

make a safe ground connection.

Dead-end Screw

c. When installing a three-phase hoist, make only temporary

connections at the power source. Push the “UP” button

and observe the direction of the load block. If it raises, the

phasing is correct and permanent connections may be

made at the power source. If the load block lowers when

the “UP” button is pushed, release the button immediately

since the limit switches will not operate to protect the hoist

from over-travel. Reverse any two wires (except the green

ground wire) at the power source to correct the load hook

direction (phasing). Do not change connections in the

hoist or pushbutton assembly.

Figure 1 — Installing Chain Container Assembly

4. Run the load hook down to its lowest position. Place the slack

end of the chain in the chain container. Feed the remainder of

the chain into the container by operating the hoist in the “UP”

direction to the top limit.This will permit the chain to pile

freely and eliminate the possibility of fouling which may occur

if the chain is placed in the container by hand.

d. Make sure load chain is not twisted as it travels into the

hoist.

OPERATION

e. Operate hoist in a hanging position only. Hoist should be

permitted to align itself for a straight line pull. Do not

attempt to pull around corners.

This hoist is designed for safe operation within the limits of its

rated capacity. It is controlled with the “UP” and “DOWN”

buttons of the pushbutton station. There are many safety

features to protect the operator from injury due to failure of the

hoist. Here are some points which should be observed to

maintain safe operation.

f. Read ASME-B30.16 Safety Code for Hoists.

3. If necessary, lubricate the chain, see LUBRICATION,

page 9.

4. Check the function of the limit switches. Before placing hoist

in operation, check limit switch adjustment. Operate

pushbutton until near stop point and inch into stop limit both

top and bottom. If either switch is not correct, adjust

according to LIMIT SWITCH ADJUSTMENT, page 8.

1. Do not overload the hoist.

2. Do not make extreme side pulls with the hoist.

3. Operate the hoist only in a hanging position with

adequate support.

4. Do not “sling” the load hook and chain around the load.

Use an approved sling.

INSTALLATION OF CHAIN CONTAINER

ASSEMBLY (OPTIONAL ACCESSARY)

Refer to Figure 1 and Table 2.

5. Be sure there are no twists in the load chain as it travels into

the hoist housing.This condition should be constantly

checked on double chain hoists because it is possible for the

load block to be “capsized” or turned over one or more times.

1. Remove dead end screw and washers and let chain hang free.

2. Place chain container bracket flush against housing.

Replace washers and screw. Tighten securely.

6. Before raising a load, always check to see that it is held

securely in the hook or sling chains, etc. Raise the load

only until the load chain is taut and then double check the

rigging before continuing to raise the load.

3. Attach chain container to bracket with two open links and

then close the links.

7. Do not stand beneath a load! Do not move a load in such a

manner as to endanger personnel.

8. Do not lower into areas where visibility is obscured unless

someone else is guiding the operation.

Do not allow load to come in contact with chain

container. If this situation exists reset the “UP” limit

switch (See LIMIT SWITCH ADJUSTMENT, page 8) so

that hook block stops below chain container.

9. Use common sense at all times when operating a hoist.

10. Do not operate if direction of hook travel is not the same as

indicated on button being pushed.

Table 2 - Optional Chain Container

Standard

Lifts

Shipping

Weight

(lbs)

Hoist

Capacity

Chain Container

Required

Dimensions in Inches

Length

(ft)

Width

Depth

11½

18½

1/2 & 1 Ton

2 Ton

10, 15, & 20

48-12-0111

48-12-0112

48-12-0113

6½

2 Ton

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

LOWERING WITHOUT POWER

If the power fails with a load suspended, the hoist will

automatically stop. In an emergency the load can be lowered

without power as follows:

Do not use hoist to lift, support or otherwise

transport people.

11. Do not operate unless hook travel limit devices function.

Test without load each shift.

1. DISCONNECT HOIST FROM POWER SUPPLY AND

REMOVE ELECTRICAL COVER.

12. Do not operate when hoist is not centered over load.

2. Open disc brake manually by using two screwdriver blades,

one on each side of the brake at a point close to the brake

spring posts. Apply pressure to the underside of the

armature plate (points “X”, Figure 6, page 9) to close the

solenoid and release the brake.

13. Do not operate if chain is not seated properly in sprockets

or sheave grooves.

14. Do not operate damaged or malfunctioning hoist.

OVERLOAD LIMITING PROTECTION

This hoist is equipped with a factory-calibrated overload

limiting clutch that will permit the lifting of loads within its rated

capacity, but will prevent the lifting of damaging overloads while

the hoist is being operated. If the load being lifted exceeds the

lifting capability of the overload clutch, the hoist motor will

continue to run, causing overheating of both the clutch and

hoist motor. This condition should be avoided by immediately

releasing the “UP” button and reducing the load to within the

rated capacity of the hoist. See GEARING, page 10, for

additional instructions on this device.

Do not allow screw driver blades to touch rotating

friction disc “C”.

Do not allow the load to descend rapidly. This causes

the motor to race and serious damage may result.

3. Use several quick releases instead of holding brake open

continuously. Do not exceed normal lowering speed.

HOOKS

The overload limiting clutch is an emergency

protective device and should not be used to measure

the maximum load to be lifted, or to sense the

overload imposed by a constrained load. While the

overload limiting clutch will protect the hoist from

damaging overloads, it will not ensure that a load is

within the rated capacity of the hoist.

Refer to Figure 2.

1. Inspect hooks once daily for cracking, extreme wear or

spreading. Replace hooks showing any of these signs. If the

throat openings are spread wider than the maximum

permissible 15% increase listed here, the hooks have been

overstressed and must be replaced. Any hook that is bent or

twisted more than 10° from the plane of an unbent hook

must also be replaced.

2. The hook latches should be inspected to ensure that they

close the hook throat opening in a secure manner when a

load is applied. Inspect the hook shank and nut for any

stripping of the threads or other damage.The hook nut should

be fully restrained by the retaining pin.

MAINTENANCE

INSPECTIONS

A planned inspection routine should be established for this

hoist based upon frequency of use, severity of use, and

environmental conditions, (Reference ASME Standard

B30.16). Some inspections should be made frequently (daily to

monthly) and others periodically (monthly to yearly). It is

strongly recommended that an Inspection and Maintenance

Check List and an Inspector’s Report, similar to those shown in

Figures 10A and 10B, be used and filed for reference. All

inspections should be performed or overseen by a designated

inspector. Special inspections should be made following any

significant repairs or any operating occurrence leading one to

suspect that the hoist’s capability may have been impaired.

3. In addition to above, load hooks should be inspected for

cracks by the magnetic particle, dye penetrant or other

suitable crack testing inspection method. This should be

done at least once a year.

Figure 2 — Hook

Inspection

“X” Dimension*

Hoist

Capacity

Top

Hook

Bottom

Hook

1 Ton & Under

2 Ton

1 / "

(*) Maximum permissible throat opening of hook.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

6. Using the “C” link, attach the new chain to the load end of

the old chain. Be sure that the welds of the upstanding links

of the new chain will face outward from the load sheave.

The end links must be oriented for attachment to the dead-

end screw and the chain support (double-chained only)

without any twist in the chain.

CHAIN

Chain is to be kept clean and lubricated (See LUBRICATION,

page 9). Visually check chain every time hoist is used. Hoist

must not be operated when chain is twisted or kinked. An

important phase of hoist maintenance is chain inspection.

Check individual links and check for chain elongation.

Note Position

of Hook

1. Check the chain for overall wear or stretch by selecting an

unworn, unstretched length of chain (at the slack end for

example). Let the chain hang vertically with a light load

(about 20 pounds) on the chain to pull it taut. Use a large

caliper to measure the outside length of a convenient

number of links (about 12"). Measure the same number of

links in a used section of chain and calculate the percentage

increase in length of the worn chain.

Dead-End

Screw

Slack End

TON

2. If the length of the worn chain is more than 1½% longer than

the unused chain (0.015" per inch of chain measured), then

the chain should be replaced. If the chain is worn less than

1½%, check it at several more places along its length. If any

section is worn more than 1½%, the chain should be replaced.

Load End

Double-chained

Hoist

Single-chained

Hoist

Chain Support

Figure 4 — Chain Replacement Diagram

The chain used on this hoist has very carefully

controlled dimensions and has been heat treated. Do

not attempt to substitute other manufacturer’s chain.

7. With the electrical cover off, connect the hoist to the power

supply. Be sure that the green ground wire is properly

grounded (See INSTALLATION, page 4).

Spring

8. Carefully jog the “UP” button and run the joined pieces of

chain into the hoist until about 15" of the new chain comes

out the other side.

Guide Plate

Silver Nut

(Down)

9. DISCONNECT HOIST FROM POWER SUPPLY.

10. Remove the “C” link and the old chain. Remove the chain

stop from the old chain by prying off its retaining ring with a

flathead screwdriver. If attached, remove the old chain from

the side of the hoist by removing the dead-end screw and

washers (note placement of washers).

Gold Nut

(Up)

11. Attach the chain stop to the slack end of the new chain by

capturing the 12^thlink with the two stop halves positioned

with their tapered ends pointing towards the hoist. Slide the

sleeve over the halves and attach the retaining ring. If you

are not using a chain container, attach the slack end of the

new chain to the side of the hoist using the dead-end screw

and washers. With factory supplied hardware there should

be six washers between the hoist and chain link and two

washers between the chain link and screw head. DO NOT

allow twists in the chain.

Figure 3 — Limit Switch Assembly

Chain Replacement with Chain in Hoist

Refer to Figures 3 & 4.

1. Run hook up to its top limit.

2. DISCONNECT HOIST FROM POWER SUPPLY and

remove the electrical cover.

12. Adjust the lower limit switch (See ADJUSTING LOWER

LIMIT, page 8).

3. Using a screwdriver, pry the spring guide plate out of the

slots in the limit switch nuts (See Figure 3). Turn the slotted

nut nearest you, the gold nut, back to about the center of

the threaded screw. Do not disconnect the wires from the

limit switches.

13. Attach the bottom block on single-chained hoists using a

new load block screw (See Figure 20). On double-chained

hoists, feed the chain through the load block (welds of the

upstanding links will be in towards the sheave) and fasten

the end of the chain to the chain support using a new chain

support pin (See Figure 20). Be sure there are no twists in

the chain.

4. Remove the load block assembly from the old chain. On

double-chained hoists detach the chain from the chain

support and pull it through the load block assembly (See

Figure 4).

14. Adjust the upper limit switch (See ADJUSTING UPPER

LIMIT, page 8).

5. Make a “C” shaped chain link by grinding through the end

link on the load end of the old chain.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Chain Replacement with No Chain in Hoist

Refer to Figures 4 and 5.

LIMIT SWITCH ADJUSTMENT

IMPORTANT: Before placing hoist in operation, check the limit

switch adjustment. Limit switches are provided to protect the

hoist against damage resulting from overtravel or to allow

setting the hook travel within the factory-set limits of travel. For

easy identification and association with the proper direction of

travel, the upper and lower limit switch adjusting nuts are color-

coded gold and silver respectively. Each limit nut has 10 slots

for fine adjustment, and the increment of adjustment is such

that one slot is equivalent to approximately one link of chain

travel. Movement of the limit switch nuts toward or away from

each other increases or decreases the hook travel respectively.

Care should be exercised when adjusting either limit of travel.

1. DISCONNECT HOIST FROM POWER SUPPLY and move

hoist to a work table. Do not remove the electrical cover.

2. Lay the hoist on its side and remove the four screws that

attach the sheave housing to the gear housing (See Figure

12, Ref. No. 2).

3. Carefully pull the sheave housing and motor assembly loose

from the gear housing.

There are wires running through the hoist. Carefully

ease the hoist sections apart. Do not jerk them apart.

4. Turn the two hoist sections at right angles and remove the

chain guide screws on the nearest chain guide (Ref. No. 1,

Figure 5).

If the wires running to the limit switches are ever

disconnected for any purpose, be sure to replace

wires in accordance with the correct wiring diagram

(See WIRING DIAGRAMS, page 12).

Adjusting Upper Limit (Gold Nut)

Refer to Figure 3.

1. Suspend the hoist. For single-chained models raise the load

block until there is a minimum clearance of 2" from the hoist

housing and the top of the block. Double-chained models

require a minimum clearance of 1" from the chain support to

the top of the load block.

2. DISCONNECT HOIST FROM POWER SUPPLY and

remove the electrical cover.

3. With a screwdriver, pry the spring guide plate out of the slots

in the limit switch nuts.

Figure 5 — Chain Replacement with No Chain in Hoist

5. Remove the two chain guide plate screws (Ref. No. 2) and

the nearest chain guide plate. Be careful not to lose the two

spacers that are between the chain guide plates.

4. Turn the slotted gold nut toward its limit switch until the

switch “clicks” then turn two slots farther. Release the spring

guide plate and be sure it slips back into the slots in both

limit switch nuts. Do not disturb the silver slotted nut if it has

been set previously.

NOTE: Inspect chain guides and load sheave for wear, replace

as needed.

Adjusting Lower Limit (Silver Nut)

Refer to Figure 3.

6. Lay the new chain over the load sheave. Allow about 15" of

chain below the hoist on the slack end (See Figure 4). Be sure

the welds of the upstanding links are out away from the load

sheave and that proper orientation is observed for attachment

of the dead end. Also be sure the load hook assembly (if

already attached to the chain) is toward the center of the hoist

or to your right as you face the load sheave.

1. Suspend the hoist. Carefully lower the load block to a point

where the slack-end loop of the chain hangs down 6" or

more from the hoist housing (or the limit desired in any

particular application allowing the minimum 6"). There

should be a minimum clearance of 1½" between the chain

stop and the bottom of the hoist.

7. Replace the chain guide plate and the chain guide. Grease

the splined shafts that project from both the housing and

the motor.

2. DISCONNECT HOIST FROM POWER SUPPLY and

remove the electrical cover.

8. Place the motor coupling on the splined shaft and carefully

fit the two hoist sections together. Be sure the dead-end nut,

the top hook and the support screw (double-chained hoists

only) are all in place. On single-chained hoists, the hook

shank goes in the center hole; on double-chained hoists, it

goes in the off-center hole (See Figure 4). Be careful not to

pinch any of the wiring. Turn the hoist on its side and replace

the four screws and tighten securely.

3. With a screwdriver, pry the spring guide plate out of the slots

in the limit switch nuts.

4. Turn the slotted silver nut toward its limit switch until the

switch “clicks,” then turn two slots farther. Release the spring

guide plate and be sure it slips back in the slots in both limit

switch nuts. Do not disturb the gold slotted nut if it has been

set previously.

Check Both Upper and Lower Limits

1. Connect the hoist to the power supply. Be sure the green

ground wire is properly grounded .

9. Follow steps 11 through 14 in the previous section, CHAIN

REPLACEMENT WITH CHAIN IN HOIST, to complete the

chain replacement procedure.

2. Check load hook direction (See INSTALLATION 2-c, page 5).

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

3. Carefully raise load block to upper limit and observe if it

stops automatically at desired level. Do not allow load block

to run into hoist housing — this will damage the hoist.

Maintain a minimum clearance of 2" from the hoist housing

and the top of the load block on single-chained models and

1" from the chain support to the top of the load block on

double-chained models.

HOIST CONTROLS

Both the pushbutton and the reversing contactor are

mechanically interlocked to prevent shorting the circuit and

causing serious damage. As part of maintenance, always

check for proper closure of contact points as well as for burned

contacts. If replacement is necessary, see Figures 16 & 18 for

replacement parts.

4. Carefully lower load block to lower limit and observe if it

stops automatically at the desired level. Do not allow slack-

end loop of chain to become taut against hoist housing. This

will damage the hoist. There should be a minimum clearance

of 1½" between the chain stop and the bottom of the hoist.

WIRING

Refer to Figures 9A and 9B

MILWAUKEE Electric Chain Hoists, which are available for

115/230V or 230/460V, are shipped wired for 115V and 460V

respectively. Conversion of dual voltage hoists to either the

higher or lower voltage can be done simply and quickly as

follows:

5. If upper and lower limits operate satisfactorily, hoist is ready

for use. If they are not as desired, repeat adjustment.

BRAKE

Properly adjusted, this brake will release promptly when

energized. It is capable of both smoothly stopping and securely

holding the rated capacity of the hoist. If the hoist develops

either undesirable over-travel after the pushbutton is released

(this condition is most noticeable in the lowering direction) or

hesitates to lift the load promptly when the pushbutton is

depressed (this condition is most noticeable in the hoisting

direction), the brake should be adjusted.

1. DISCONNECT HOIST FROM POWER SUPPLY and

remove the electrical cover.

2. Each dual-voltage hoist has a terminal block assembly for

the interconnection of the electrical components of the hoist.

To convert voltage, reconnect the leads to the terminal

blocks according to the wiring diagram located inside the

electrical cover and also in Figures 9A & 9B. DO NOT move

any wires or make any changes to the electrical circuit

except at the terminal block assembly. Tug on wires to

ensure they are securely connected.

Brake Adjustment

Refer to Figure 6.

3. After converting voltage, recheck phasing and limit switch

operation (See INSTALLATION 2-c & 4, page 5).

1. DISCONNECT HOIST FROM POWER SUPPLY and

remove the electrical cover.

IMPORTANT: Always refer to the wiring diagram located on

the inside of the electrical cover or Figures 9A and 9B when

performing electrical repairs. Make sure all connections are

secure and check for damaged insulation. It is also imperative

that the power circuit has conductors of adequate size (See

Table 3).

Gap

LUBRICATION

Refer to Figure 11.

Proper lubrication is necessary for a long and relatively trouble-

free hoist operation. Refer to the following and the

RECOMMENDED LUBRICATION SCHEDULE for lubrication

points, type of lubricant, and frequency of lubrication.

Figure 6 — Brake Assembly

2. With reference to Figure 6, the gap between the brake

armature “A” and the field “B” should be checked. The

correct gap is 0.015". Adjustment should not be necessary

until gap reaches 0.040".

Load Chain

Clean the load chain with acid-free solvent and coat with

SAE 90 gear oil. Wipe excess oil to prevent dripping. Never

apply grease to the chain.

3. Adjust gap by adjusting the 3 locknuts “F” and checking with

a feeler gauge to be sure gap is the same on both ends of

the solenoid.

Gearing

The gear case of this hoist is filled at assembly with

approximately 1½ pints of SAE 90 EP gear oil. Check oil level

by removing the oil level check plug from the side of the hoist.

With the hoist hanging level, gear oil should be even with the

hole. Change oil periodically depending on the severity of the

application and the environmental conditions (at least every

200 hours of run time).

4. Adjustment is now complete and the brake properly set.

Replace the electrical cover, reconnect the power supply,

and check hoist brake action.

Be sure the bottom of the armature does not bear

against the splined adapter “H”. As adjustments are

made, the built-in clearance will be reduced. When

this clearance is gone REPLACE BRAKE DISCS.

Minimum allowable disc thickness is .162". See

Figure 15 for further illustration.

Bearings

All bearings except hook and idler sheave bearings are

lubricated at the factory and should not require additional

lubrication. Noisy or worn bearings should be replaced.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Limit Switch Shaft

5. Refer to Figure 17 to disassemble the limit switch.

See LIMIT SWITCH ADJUSTMENT on page 8 to properly

set the upper and lower limits of travel.

Remove any dirt accumulation and spray with a general

purpose lubricant.

6. Refer to Figure 18 for repairs on the pushbutton station. Also

refer to the wiring diagram inside the electrical cover or

Figures 9A and 9B for wiring instructions.

Hook Bearing

Apply a few drops of SAE 30 gear or motor oil around the edge

of the bearing.

Idler Sheave Bearing (Bushing)

Disassemble load block and apply a light coat of NLGI #2

grease, or equivalent, inside of bearing.

HOIST REPAIRS

NOTE: If you do not have an experienced mechanic to do your

repair work, we recommend that you send your hoist to an

approved service station for repairs. Use authorized repair

parts only.

1. For major repairs or when the hoist is to be sectioned in the

suspension area, it will be necessary to move the hoist to a

workbench or table.

Figure 7 - Electrical Panel Removed

Motor

Remove load and disconnect hoist from power supply

before starting to do any repairs or to take any

sections apart.

Refer to Figures 12, 13 and 14

The hoist motor is located on the opposite end to that of the

electrical parts, but the two are tied together with electrical

leads running through the housing.

2. For repairs which can be done by removing the electrical

cover only, the hoist need not be moved. Lowering the hoist

to a convenient working level is desirable.

1. If it is necessary to replace or repair the motor,

DISCONNECT THE HOIST FROM THE POWER SUPPLY

and remove the electrical cover.

The following repair instructions will help you in understanding

repair procedures, when related to the Replacement Parts List

starting on page 16. For clarity these are broken down into

areas.

2. Loosen the screw clamps on the terminal blocks and

reversing contactor to disconnect the motor leads (See

Figure 16).

Electrical Parts and Brake

3. Remove the four motor mounting bolts attaching the motor

to the housing. It will come loose at the motor coupling.

Refer to Figures 9A, 9B & 16.

1. Remove the cover to access the controls. Single-phase

models also have a starting switch and capacitor mounted on

the motor as shown in Figure 13.The terminal blocks and end

clamps snap off of the rails on the plate using a small

screwdriver. DO NOT SLIDE THE END CLAMPS.

4. Inspect the motor coupling, motor shaft and all the bearings.

Replace as necessary.

5. Install new or repaired motor according to the wiring diagram

located inside the electrical cover or Figures 9A and 9B.

Gearing

The reversing contactor can be slid off the rail, but it must be

snapped on. Where the contactor fits the rail, one side has

springs or pads that apply pressure against the edge of the

rail. By pressing against that side at the base of the contactor,

you can snap the part on or off using a rotating action. Note

the numbers that label the terminals on the contactor and

orient the part as shown in Figures 9A & 9B. Single-phase

contactors have a small jumper that is not present on the

3-phase (note the 3 and 5 terminals on the reversing

contactor in Figure 9A).

Use the Replacement Parts List for Basic Hoist and

Transmission Parts to help in repairs on gearing (See Figures

12 and 19). As disassembly is extensive for gearing,

disconnect hoist and move to a workbench.

1. Remove electrical cover.

2. Remove electrical panel.

3. Remove brake assembly and limit switch assembly.

4. Drain oil from transmission.

2. Remove the electrical panel by removing the stand-off

screws (See Figure 16). The limit switch and brake are now

accessible as shown in Figure 7.

3. Remove the transformer bolted to the back of the panel plate

if it requires replacement.

Do not disassemble or readjust clutch, or replace with

a clutch assembly from another hoist. Doing so will

void the warranty and may create an unsafe condition.

If replacement is needed due to wear or loss of

adjustment, always use a new clutch assembly.

4. Refer to Figure 15 to disassemble the brake. See BRAKE

ADJUSTMENT on page 9 to properly set the brake.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Failure to follow proper lockout/tagout procedures may

present the danger of electrical shock.

TO AVOID INJURY:

Disconnect power and lockout/tagout disconnecting

means before removing cover or servicing this

equipment.

Suspension

Use Replacement Parts List for Basic Hoist and Chaining Parts

to help in repairs in this section (See Figures 12 and 20). The

hoist sections must be separated at the top hook line in order

to inspect the load sheave and chain guides. See CHAIN

REPLACEMENT WITH NO CHAIN IN HOIST, page 8.

Figure 8 - Assembled Gearing

5. Remove four screws attaching gear box cover to gear

housing and remove gear box cover. Limit switch drive shaft

will come along with the cover.

6. Inspect gears for broken or severely worn teeth and inspect

all bearings. Replace as necessary. The overload slip clutch

is factory calibrated and must not be disassembled or

readjusted.

While this section is apart, check the following:

• Load sheave

7. Reassemble in reverse order of disassembly making sure

gasket is in place and in good condition. Coat gasket with

Permatex^®or other gasket cement. Extreme care should be

taken to avoid damage to oil seals.

• Chain guides and plates

• Chain

8. Check all wire terminals to be sure they are properly seated

and in accordance with wiring diagram. Before placing

hoist back into service, check brake adjustment and limit

switch stops.

• Chain support (on 2 ton models)

• Bearings

Replace parts as necessary including screws, lockwashers,

etc.

When reassembled, recheck limit switch operation. See LIMIT

SWITCH ADJUSTMENT, page 8.

POWER CORD PRECAUTIONS WITH 1-PHASE HOISTS

Electric hoists require a sufficient power supply. It is especially important with single-phase voltage to ensure that the conductors

running to the hoist from the power source are adequate in size to handle the power requirements of the hoist. Inadequate

power cables and branch circuits will cause low voltage, high amperage, damage to the hoist, and potential fire hazards.

Such problems can be minimized by using 230V power on 115/230V hoists. The following are recommendations for the conductor

gage size depending on the length, horsepower, and voltage.

Table 3 - Recommended Conductor Sizes for 1-Phase Hoists

M a x i m u m L e n g t h o f P o w e r C o r d i n F e e t

Voltage

14 AWG

12 AWG

10 AWG

8 AWG

(1-Phase)

1/2

115V

230V

100

520

150

810

200

330

115V

230V

120

190

310

490

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Figure 9A — Wiring Diagram for 1-Speed, 1-Phase Models

Figure 9B — Wiring Diagram for 1-Speed, 3-Phase Models

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

TROUBLE SHOOTING

Always disconnect unit from the power supply system before removing hoist covers or the back cover of control station.

––– Remedy–––

––– Probable Cause –––

Hook fails to stop at end of travel

1. Limit switch not operating

1. Check adjustment (See LIMIT SWITCH ADJUSTMENT, page 8). Check connections against wiring diagram.

Tighten loose connections or replace.

2. Brass limit switch nuts not moving on shaft

3. Hoist reversing contactor malfunctioning

2. Check for stripped threads or bent nut guide.

3. Remove electrical cover and check reversing contactor.

Hoist does not respond to pushbutton

1. Power failure in supply lines

2. Wrong voltage or frequency

3. Improper connections in hoist or pushbutton

station

1. Check circuit breakers, switches and connections in power supply lines.

2. Check voltage and frequency of power supply against the rating on the nameplate of the motor.

3. Check all connections at line connectors and on terminal block. Check terminal block on dual voltage hoists for

proper voltage connections.

4. Check connections to the solenoid coil. Check for open or short circuit. Check for proper adjustment (See BRAKE

ADJUSTMENT, page 9).

4. Brake does not release

5. Faulty hoist reversing contactor

5. Check coils for open or short circuit. Check all connections in control circuit. Check for burned contacts.

Replace as needed.

Hook does not stop promptly

1. Hoist overloaded

2. Brake not holding

1. Reduce load to within rated capacity of hoist.

2. Check brake adjustment (See BRAKE ADJUSTMENT, page 9). It may be necessary to replace discs.

Hook moves in wrong direction

1. Three phase reversal

2. Improper connections

1. Reverse any two wires (except the green ground wire) at the power source (See INSTALLATION 2c, page 5).

2. Check all connections against wiring diagram.

Hoist hesitates to lift when energized

1. Hoist overloaded

1. Reduce load within rated capacity of hoist.

2. Check motor brake adjustment (See BRAKE ADJUSTMENT, page 9).

3. Replace clutch.

4. Determine cause of low voltage and bring up to within plus or minus 10% of the voltage specified on the motor.

Measure voltage at the hoist reversing contactor while lifting a load.

5. Replace faulty component.

2. Motor brake requires adjustment

3. Worn overload limiting clutch

4. Low voltage

5. Faulty SINPAC^®starting switch or start capacitor

(single phase hoists only)

Hook raises but will not lower

1. “DOWN” circuit open

2. Broken conductor in pushbutton cable

3. Faulty hoist reversing contactor

1. Check circuit for loose connections. Check “DOWN” limit switch for malfunction.

2. Check each conductor in the cable. If one is broken, replace entire cable.

3. Check coils for open or short circuit. Check all connections in control circuit. Check for burned contacts.

Replace as needed.

4. Loose screw clamps

4. Ensure that screw clamps are tightened on the terminal blocks and reversing contactor.

Hook lowers but will not raise

1. Hoist overloaded

2. Low voltage

1. Reduce load to within rated capacity of hoist.

2. Determine cause of low voltage and bring up to within plus or minus 10% of the voltage specified on the motor.

Measure voltage at the hoist reversing contactor while lifting a load.

3. Check circuit for loose connections. Check “UP” limit switch for malfunction.

4. Check each conductor in the cable. If one is broken, replace entire cable.

5. Check coils for open or short circuit, check all connections in control circuit. Check for burned contacts.

Replace as needed.

3. “UP” circuit open

4. Broken conductor in pushbutton cable

5. Faulty hoist reversing contactor

6. Faulty capacitor (single phase hoist only)

7. Worn overload limiting clutch

8. Loose screw clamps

6. Check starting capacitor on motor. Replace if necessary.

7. Replace overload clutch assembly.

8. Ensure that screw clamps are tightened on the terminal blocks and reversing contactor.

Motor overheats

1. Excessive load

2. Low voltage

1. Reduce load to within rated capacity of hoist.

2. Determine cause of low voltage and bring up to within plus or minus 10% of the voltage specified on the motor.

Measure voltage at the hoist reversing contactor while lifting a load.

3. Extreme external heating

4. Frequent starting or reversing

5. Brake dragging

3. As the ambient temperature rises towards the 130°F limitation of the unit, frequency of the hoist operation must be

limited to avoid overheating of the motor. See ADVERSE ENVIRONMENTAL CONDITIONS, page 4.

4. Excessive inching, jogging or reversing should be avoided since this type of operation will drastically shorten the life

of motor, contactor and brake.

5. Check brake adjustment (See BRAKE ADJUSTMENT, page 9).

Lack of proper lifting speed

1. Hoist overloaded

2. Brake dragging

1. Reduce load to within rated capacity of hoist.

2. Check for proper brake adjustment or other defects.

3. Ensure that the voltage at the reversing contactor is within ±10% of the nominal voltage while lifting a load.

4. Replace overload clutch assembly.

Low voltage

4. Overload limiting clutch intermittently slipping

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

TROUBLE SHOOTING (Continued)

Motor brake noise or chatter (while starting hoist)

1. Brake needs adjustment

2. Low voltage

1. See BRAKE ADJUSTMENT, page 9.

2. Check voltage at the hoist reversing contactor while the hoist is lifting a load.Voltage should be no less than 90% of

the voltage specified. 115 volt hoists are particularly subject to voltage drop problems due to their high current draw.

Conversion to 230 volt operation is suggested in extreme cases.

Motor brake “buzz” (anytime hoist is running)

1. Brake needs adjustment

2. Broken shading coil on brake frame

1. See BRAKE ADJUSTMENT, page 9.

2. Replace shading coil or complete brake frame assembly.

INSPECTION AND MAINTENANCE CHECK LIST

ELECTRIC POWERED OVERHEAD CHAIN HOIST

Type of Hoist______________________________________________________

Location _________________________________________________________

Manufacturer______________________________________________________

Capacity (Tons) ____________________________________________

Original Installation Date _____________________________________

Manufacturer’s Serial No. ____________________________________

Item

Frequency of Inspection

Frequent Periodic

Monthly

Possible Deficiencies

Action

Required

Daily

1-12 Mo.

Operating Controls

Any deficiency causing improper operation

1. Any deficiency causing improper operation

2. Pitting or deterioration

Limit Switches

1. Slippage or excessive drift

Brake Mechanism

2. Glazing, contamination or excessive wear

Excessive throat opening 15% bent or twisted more than 10

degrees, damaged hook latch, wear, chemical damage,

worn hook bearing. To find cracks, (use dye penetrant,

magnetic or other suitable detection methods)

Hooks

Cracks, excessive wear or other damage which may impair

the strength of the lug. To find cracks, (use dye penetrant,

magnetic particle or other suitable detection methods)

Suspension Lug (if used)

Chain

Inadequate lubrication, excessive wear or stretch, cracked,

damaged or twisted links, corrosion or foreign substance

Hook and Suspension

Lug Connections

Cracks, bending, stripped threads

Pins, Bearings, Bushings

Shafts, Couplings

Excessive wear, corrosion, cracks, distortion

Nuts, Bolts, Rivets

Sheaves

Looseness, stripped and damaged threads, corrosion

Distortion, cracks, and excessive wear.

Build-up of foreign substances

Cracks, distortion. Excessive wear, internal build-up of

foreign substances

Housings, Load Block

Wiring and Terminals

Fraying, defective insulation

Hoist Reversing

Contactor, other Electrical

Apparatus

Loose connections, burned or pitted contacts

Supporting Structure

and Trolley (if used)

Damage or wear which restricts ability to support

imposed loads

Nameplates, Decals,

Warning Labels

Missing, damaged or illegible

NOTE: Refer to Maintenance and Inspection Sections of the Hoist-Maintenance Manual for further details.

FREQUENCY OF INSPECTION

Frequent — Indicates items requiring inspection daily to monthly. Daily inspections may be performed by the operator if properly designated.

Periodic — Indicates items requiring inspection monthly to yearly. Inspections to be performed by or under the direction of a properly designated period. The exact

period of inspection will depend on frequency and type of usage. Determination of this period will be based on the user’s experience. It is recommended

that the user begin with a monthly inspection and extend the periods to quarterly, semi-annually or annually based on user’s monthly experience.

Figure 10A — Recommended Inspection and Maintenance Check List

NOTE: This inspection and maintenance check list is in accordance with our interpretation of the requirements of the Safety

Standard for Overhead Hoists ASME B30.16. It is, however, the ultimate responsibility of the employer/user to interpret and

adhere to the applicable requirements of this safety standard.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

INSPECTOR’S REPORT

ITEM

REMARKS (LIST DEFICIENCIES AND RECOMMENDED ACTION)

Inspector’s

Signature

Date

Inspected

Approved by

Date

Figure 10B — Recommended Inspector’s Report

RECOMMENDED LUBRICATION SCHEDULE*

MILWAUKEE ELECTRIC POWERED CHAIN HOIST

PAGE AND

COMPONENT

Load Chain

TYPE OF LUBRICANT

TYPE OF SERVICE AND

REFERENCE NO.

FREQUENCY OF LUBRICATION

HEAVY

Daily

NORMAL

Weekly

INFREQUENT

Monthly

Figure 20

Ref. No. 18

SAE 90 gear oil

Figure 19

Gearing

SAE 90 extreme pressure gear oil

General purpose spray lubricant

At periodic inspection (See Figure 10A)

Figure 17

Ref. No. 9

Limit Switch Shaft

Monthly

Weekly

Yearly

Figure 20

Ref. No. 38, 50

Load Hook Bearing

SAE 30 gear or motor oil

Monthly

NLGI #2 multi-purpose

lithium base grease

Figure 20

Ref. No. 44

Idler Sheave Bearing

(Bushing) Assembly

At periodic inspection (See Figure 10A)

NOTE: All bearings except hook and idler sheave bearings are prelubricated and sealed.

(*) This lubrication schedule is based on a hoist operating in normal environment conditions. Hoists operating in adverse

atmospheres containing excessive heat, corrosive fumes or vapors, abrasive dust, etc., should be lubricated more frequently.

Figure 11 — Recommended Lubrication Schedule

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Figure 12 - Basic Hoist

Parts List for Basic Hoist

Ref

No.

Description

Qty

Ref

No.

Description

Qty

Motor

1/4-20UNC X 3/4" Screw

10-24UNC X 1/2" Screw

(See Figures 13 & 14)

Sheave Housing Screw

Sheave Housing

1/2 Ton

Top Hook Assembly w/Latch

Rigid (Standard)

Swivel (Optional Part)

Latch Kit Assembly

Hook Hole Cover

MILWAUKEE Decal

Capacity Decal

1 & 2 Ton

Gear Housing

1/2 Ton

1 & 2 Ton

Gear Case Gasket

Gearbox Cover

Electrical Cover Gasket

Electrical Cover

1/4" Spring Lockwasher

1/2 Ton

1 Ton

2 Ton

Nylon Cover (Optional Accessory)

* Not Shown

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Figure 13 - Hoist Motor, 1-Phase

Parts List for Hoist Motor, 1-Phase

Ref.

No.

Description

Qty

Hoist Motor

1/2 hp, 115/230V-1Ph

1 hp, 115/230V-1Ph

Stator Assembly*

Rotor Assembly*

End Shield

Rear Bearing

Front Bearing

Shim washer

Capacitor

1/2 hp

1 hp

SINPAC^®Starting Switch

Capacitor/Start Switch Cover

Rubber Gasket

Thru Bolt

1/2 hp

1 hp

#10 Spring Lockwasher

8-32UNC X 5/16" Screw

*Not available as repair part.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Figure 14 - Hoist Motor, 3-Phase

Parts List for Hoist Motor, 3-Phase

Ref.

No.

Description

Qty

Hoist Motor

1/2 hp, 230/460V-3Ph-60Hz

1 hp, 230/460V-3Ph-60Hz

Stator Assembly*

Rotor Assembly*

End Shield

Rear Bearing

Front Bearing

Shim washer

Thru Bolt

1/2 hp

1 hp

#10 Spring Lockwasher

*Not available as repair part.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Figure 15 - Brake & Solenoid Parts

NOTE: Refer to wiring diagram inside

electrical cover of hoist or Figures 9A &

9B when connecting any wires.

Parts List for Brake & Solenoid Parts

Ref.

No.

Description

Qty

Disc Brake Assembly

1/2 hp, 115/230V

1 hp, 115/230V

1/2 hp, 230/460V

1 hp, 230/460V

Plate & Stud Assembly

Brake Disc

1/2 hp

1 hp

Brake Plate

Plate & Armature Assembly

Spring

Retainer

Plate & Frame Assembly

Brake Coil

115/230V

230/460V

Locknut

Adapter

Screw

Retaining Ring

Shading Coil

Shading Coil Adhesive

Spacer for 1/2 hp

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Figure 16 - Electrical Parts

Parts List for Electrical Parts

Ref

No.

Description

Qty

Ref

No.

Description

Qty

Gear Box Cover

Panel Plate

End Clamp

Marking Strip

15 ft Power Cord Assembly

Reversing Contactor

1 hp, 115/230V

1 hp, 230/460V

1/2 hp

115/230V, 1/2 hp (3 cond., 14 AWG)

115/230V, 1 hp (3 cond., 12 AWG)

230/460V (4 cond., 14 AWG)

PB & Cable Assembly

Transformer

Pri.: 115/230V, Sec.: 24V

Pri.: 230/460V, Sec.: 24V

Terminal Block

115/230V

(See Figure 18)

Panel Standoff Spacer

1/4" Internal-tooth Lockwasher

1/4-20UNC X 4" Screw

8-32UNC X 5/16" Screw

#8 External-tooth Lockwasher

1/4" Flatwasher

230/460V

Terminal Block 115/230V

End Plate

115/230V

10-24UNC X 1/2" Screw

Grommet

230/460V

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Figure 17 - Limit Switch Parts

Parts List for Limit Switch Parts

Ref

No.

Description

Qty

Ref

No.

Description

Qty

Gear Box Cover

Limit Switch Shaft

Limit Switch Nut (Silver)

Limit Switch Nut (Gold)

Retaining Ring

Limit Switch & Shaft Assembly

(Includes Items 4-12)

Limit Switch Assembly

(Includes Items 4-8)

Insulator

Switch

Limit Switch Stub Shaft

E-Ring

6-32UNC X 1" Screw

6-32UNC Elastic Locknut

Spring

Limit Switch Bracket

(Includes Item 8)

10-24UNC X 1/2" Screw

Bushing

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Figure 18 - Pushbutton Station

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Parts List for Pushbutton Station

Ref.

No.

Description

Qty

Pushbutton Station & Control Cable Assembly

6 ft Cable Length

11 ft Cable Length

16 ft Cable Length

Special Drop

Pushbutton Station Assembly

Control Cable Assembly

6 ft Cable Length

11 ft Cable Length

16 ft Cable Length

Special Drop

Enclosure

Gasket

Contact Assembly

(Includes Items 6 & 7)

Button Assembly

Grommet

Hardware Kit

(Includes Items 9-16)

Warning Tag

▲

(▲ ) Not shown.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Figure 19 - Transmission Parts

*32

*NOTE: Orient output gear (32) with long boss

towards gear housing (2) on 1/2 ton

models and towards gear box cover (3) on

1 & 2 ton models.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Parts List for Transmission Parts

Ref.

No.

Description

Qty

Sheave Housing

1/2 Ton

1 & 2 Ton

Gear Housing (Includes Oil Seals)

1/2 Ton

1 & 2 Ton

Gear Box Cover

(Includes Oil Seals)

Spring Washer

O-Ring

Pressure Relief Fitting

Dowel Pin

Gear Case Gasket

Oil Fill Plug

Oil Drain Plug

Oil Level Check Plug

Oil Seal

Screw

Motor Coupling

Oil Seal

Bearing

Input Pinion

Retaining Ring

Brake Adapter

Bearing

High Speed Gear

Intermediate Pinion

1/2 Ton

1 & 2 Ton

Bearing

Output Pinion

Overload Clutch Assembly

1/2 Ton

1 & 2 Ton

Retaining Ring

Bearing

Load Sheave Shaft Assembly

(See Figure 20)

Load Sheave

(See Figure 20)

Spacer

(See Figure 20)

Oil Seal

Output Gear

1/2 Ton

1 & 2 Ton

SAE 90 EP Gear Oil

1½ pt

* Not Shown

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Figure 20 - Chaining Parts

2-Ton

Models

1/2 -Ton

Models

2-Ton Models

1-Ton Models

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

Parts List for Chaining Parts

Ref

No.

Description

Qty

Ref

No.

Description

Qty

Sheave Housing

1/2 Ton

Chain Support

Chain Support Pin

Cotter Pin

1 & 2 Ton

Gear Housing

1/2 Ton

Lockwasher

1/2-20UNF Hex Jam Nut

Chain Support Screw

Load Block Assembly, 1/2 Ton

Load Block Frame

Load Block Frame (Threaded)

Load Block Screw

Load Block Assembly, 1 Ton

Load Block Frame

1/4-20UNC x 1¼"

Socket Head Cap Screw

1/4" Internal-Tooth Lockwasher

Load Block Pin

1 & 2 Ton

Dowel Pin

Load Sheave

1/2 Ton

1 & 2 Ton

Load Sheave Shaft

Roll Pin

Spacer, 1 & 2 Ton

Chain Guide

1/2 Ton

1 & 2 Ton

Chain Guide Screw

Washer, 1/2 Ton

Chain Guide Plate

1/2 Ton

Bottom Hook Assembly

w/Latch, 1 & 1/2 Ton

Latch Kit

Slotted Hex Nut

1 & 2 Ton

Bearing

Chain Guide Plate Screw

Chain Guide Plate Spacer

Bearing

Load Block Assembly, 2 Ton

Load Block Frame

Load Block Screw

3/8-24 UNF Hex Locknut

Sheave Shaft Assembly

Sheave & Bearing Assembly

Sheave Shaft

Dead End Screw

1/4" Flatwasher

Dead End Nut

Load Chain

1/2 Ton

•

Roll Pin

1 & 2 Ton

Bottom Hook Assembly

with Latch, 2 Ton

Chain Stop Kit

1/2 Ton

Latch Kit

1 & 2 Ton

Slotted Hex Nut

(Kits include halves,

sleeve, and retaining ring)

Bearing

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

AUTHORIZED WARRANTY REPAIR CENTERS AND PARTS DEPOTS

As a user of MILWAUKEE hoists, you are assured of reliable repair and parts services through a network of Master Parts Depots and Service

Centers that are strategically located across the United States, its territories and Canada. These facilities have been selected on the basis of

their demonstrated ability to handle all parts and repair requirements promptly and efficiently. Below is a list of the Authorized Warranty Repair

Centers and Parts Depots located in United States, its territories and Canada.

UNITED STATES

ALABAMA

MICHIGAN

GEORGIA

**TOOL SMITH CO.

1300 4th Ave.S.

*COMMERCIAL GROUP

9955 Grand River

**ACE INDUSTRIES INC.

6295 McDonough Drive

Norcross GA 30093

Birmingham AL 35233

(205) 323-2576 or (800) 317-8665

Fax (205) 323-9060

Detroit MI 48204

(770) 441-0898 or (800) 733-2231

Fax (800) 628-3648

(313) 931-6100 or (800) 931-7701

Fax (313) 491-1753

ARKANSAS

*GAFFEY INC.

**CONTINENTAL CRANE & SERVICE CO.

33681 Groesbeck Hwy.

**HI-SPEED HOIST & CRANE

701 N. Maple St,

471 Sessions St.

Marietta GA 30060

Fraser Ml 48026

N. Little Rock AR 72114

(501) 375-9178 Fax (501) 375-4254

(770) 939-6443 or (800) 820-6443

Fax (770) 422-2255

(586) 293-3870 Fax (586) 293-0017

**STEWART ENGINEERING & SALES

2140 Aurora Ave.

**HANDLING SYSTEMS & CONVEYORS INC

10909 East Otter Creek Rd.

ILLINOIS

**INDUSTRIAL TOOL PRODUCTS

919 N. Central Ave.

Muskegon MI 49442

Mabelville AR 72103

(231) 767-2140 Fax (231) 767-2233

(501) 455-5898 Fax (501) 455-6179

Woodale IL 60191

(630) 766-4040 or (800) 525-9654

Fax (630) 766-4166

MINNESOTA

ARIZONA

**MECHANICS TOOL SERVICE

1301 E. Apache Park Place

Tuscon AZ 85714

**ELECTRIC MOTOR REPAIR, INC.

2010 N. 4th St.

*S & K AIR POWER

Minneapolis MN 55411

(612) 522-3318 or (800) 345-0198

Fax (612) 588-1617

Rt. 316 E., Box 1279

(520) 889-8484 AZ only (800) 372-6700

Fax (520) 889-6668

Mattoon IL 61938

(217) 258-8500 (IL only-800-955-8501)

Fax (217) 258-8571

CALIFORNIA

**J & B EQUIPMENT

**ARROW CRANE HOIST CORP.

12714 South Carmenita Road

Santa Fe Springs CA 90670

(562) 921-8328 Fax (562) 921-9307

**SIEVERT ELECTRIC SERVICE

1230 South Hannah

8200 Grand Avenue South

Bloomington MN 55420

Forest Park IL 60130

(952) 884-2040 Fax (952) 346-1139

(708) 771-1600 or (800) 322-9144

Fax (708) 771-3124

***PERFECTION CRANE & HOIST INC.

201 DeGraff Ave.

**IDG. CALIFORNIA

6842 Walker Street

INDIANA

Swanville MN 56382

LaPalma CA 90623

**BREHOB CORP.

(320) 547-2401 or (800) 253-6829

Fax (800) 353-2254

(714) 994-6960 or (800) 464-5669

Fax (714) 521-0105

1334 S. Meridian St.

Indianapolis IN 46225

(317) 231 8080 or (800) 632-4451

Fax (317) 231-8072

**TOTAL TOOL SUPPLY

315 N. Pierce St.

**CRANEWORKS, INC.

2585 Nicholson Street

San Leandro CA 94577

St. Paul MN 55104

**MATERIALS HANDLING EQUIPMENT

7433 US 30 East

(510) 357-4000 Fax (510) 357-4099

(952) 646-4055 or (800) 444-4899

Fax (952) 646-8610

Fort Wayne IN 46803

**KIMMERLE BROTHERS, INC.

12060 East Florence St.

(219) 749-0475 or (800) 443-6432

Fax (219) 749-0481

MISSOURI

Santa Fe Springs CA 90670

**HERTZ EQUIPMENT RENTAL & SUPPLY

800 E. 18th St.

(562) 946-6771 Fax (562) 944-3473

IOWA

**ALTER & SONS, INC.

514 S. Howell St.

Kansas City MO 64108

(816) 221-7788 or (800) 669-7788

Fax (816) 221-0817

**KIMMERLE BROTHERS, INC.

226 11th St.

Davenport IA 52808

(563) 323-3601 or (800) 553-1111

Fax (563) 324-0138

San Franciso CA 94103

(415) 431-1163 Fax (415) 431-1693

**HANDLING SYSTEMS INC.

11678 Gravois Rd.

**KIMMERLE BROTHERS, INC.

337 “M” St.

KENTUCKY

St. Louis MO 63126

**ADVANCED SHERMAN

330 North Spring St.

(314) 842-7263 Fax (314) 842-5041

Fresno CA 93721

(559) 233-1278 Fax (559) 233-4678

Louisville KY 40206

**ZELLER ELECTRIC

(502) 896-2166 (KY only-800-633-8186)

Fax (502) 897-9837

COLORADO

4250 Hoftmeister

**CRANE REPAIR CO.

3718 Norwood Drive

Littleton CO 80125

(303) 791-7918 or (800) 878-7918

Fax (303) 791-7179

St. Louis MO 63125

(314) 638-9641 (Outside MO (800) 530-5810)

Fax (314) 638-6318

LOUISIANA

**RENTAL SERVICE

3301 Cities Service Hwy

West Lake LA 70669

(337) 882-6011

MONTANA

**POWER SERVICE OF MONTANA, INC.

4025 1st Ave.

FLORIDA

Fax (337) 882-0527

**J. HERBERT CORP.

1751 S. John Young Parkway

Kissimmee FL 32741

(407) 846-0588 or (800) 255-0588

Fax (407) 846-8042

Billings Montana 59101

(406) 252-8114 or (800) 823-8665

Fax (406) 259-3956

**DRILLCO

12649 S. Choctaw Dr.

Baton Rouge LA 70815

(225) 272-8251or (800) 851-3821

Fax (800) 315-9225

NEW JERSEY

**SISSCO

**MATERIAL HANDLING SYSTEMS

720 S.W. 4th Court

186 Route 206 South

Hillsborough NJ 08844

(908) 359-9767 or (800) 392-0146

Fax (908) 359-9773

Dania FL 33004

(954) 921-1171 or (888) 424-6478

Fax (954) 921-7117

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

UNITED STATES

WASHINGTON

NEW YORK

PENNSYLVANIA (cont’d)

**B & J INDUSTRIAL SUPPLY

5601 1st Avenue S.

**ABC ELECTRIC

**MORRIS MATERIAL HANDLING

Tinicum Ind. Park Building E

10 Industrial Highway MS 80

Lester PA 19113

24-25 46th Street.

Seattle WA 98108

Long Island City NY 11103

(718) 956-0000 or (N.Y. only-800-562-1919)

FAX (718) 956-4455

(206) 762-4430 or (800) 767-4430

Fax (206) 762-5329

(800) 346-2098

Fax (610) 521-5907

WEST VIRGINIA

**BEATON INDUSTRIAL, INC.

6083 Trenton Rd.

**MSC SERVICES GROUP

215 Hal Greer Blvd.

**REPAIR UNLIMITED

1730 Rockwell Road

Utica NY 13502

Huntington WV 25725

(304) 529-4171 or (800) 624-3435

Fax (304) 529-4193

(315) 797-9346 (N.Y. only-800-724-4052)

Fax (315) 797-9321

Abington PA 19001

(215) 657-3335 or (800) 369-5891

Fax (215) 784-0343

**VOLLAND ELECTRIC EQUIPMENT CO.

75 Innsbruck Drive

WISCONSIN

RHODE ISLAND

**ALFERI INDUSTRIAL SALES & SERVICE

346 Smith Street

Buffalo NY 14227

**MOTORS , HOIST & CONTROLS INC.

179 Railroad Street

(716) 656-9900 Fax (716) 656-8899

Neenah WI 54956

Woonsocket RI 02895

(920) 722-6483 Fax (920) 722-6489

NORTH CAROLINA

(401) 767-4568 Fax (401) 767-4567

**CAROLINA HOIST

*LIFT INC.

3310 E. Wendover Avenue

Greensboro NC 27405

(336) 375-6050 or (800) 326-3655

Fax (336) 375-6053

SOUTH CAROLINA

6667 W. Mill Road

**ENGINEERED SYSTEMS, INC.

1121 Duncan-Reidville Road

Duncan SC 29334

Milwaukee WI 53218

(414) 353-5353 or (800) 728-5438

Fax (414) 353-4444

(864) 879-7438 or (800) 879-7438

Fax (864) 848-3143

**SOUTHERN ELECTRIC SERVICE

2225 Freedom Drive

*TRESTER HOIST & EQUIPMENT

W136 N4863 Campbell Dr. Suite 4

Menomonee Falls WI 53051

(262) 790-0700 or (800) 234-6098

Fax (262) 790-1009

Charlotte NC 28266

TENNESSEE

(704) 372- 4832 or (800) 487-3726

Fax (704) 342-2604

**HOIST & CRANE CO.

2508 Perimeter Place

Nashville TN 37214

OHIO

(615) 242-3383 or (888) 464-7811

Fax (615) 255- 4379

**CRANE AMERICA - H. W. HOUSE

920 Deneen Avenue

U.S. TERRITORIES

Monroe OH 45050

**HI-SPEED ELECTRICAL CO.

3013 Thomas Street

(513) 539-9770 or (800) 331-5326

Fax (513) 539-9577

Puerto Rico

Memphis TN 38127

MUSIQUE EXPRESS

(901) 357-6231 Fax (901) 357-6238

State Rd.174 Block 11 No.16

Santa Rosa Bayamon PR 00959

(787) 787-2306 Fax (787) 785-4882

**AMERICRANE & HOIST CORP.

13224 Enterprise Avenue

Cleveland OH 44135

TEXAS

**ABEL EQUIPMENT CO., INC.

3710 Cavalier Drive

(216) 267-9100 or (800) 652-1932

Fax (216) 267-9131

Garland TX 75042

(972) 272-7706 Fax (800) 272-2235

*SAMSEL SUPPLY CO.

1285 Old River Road

**GAFFEY, INC.

Cleveland OH 44113

4301 Garland Drive

(216) 241-0333 or (800) 892-8012

Fax (216) 241-3426

Ft. Worth TX 76117

(817) 281-1994 or (800) 284-4233

Fax (817) 581-7831

OKLAHOMA

**GAFFEY INC.

**GAFFEY, INC.

9655 E. 522 Road

4003 S. County Road 1297

Odessa TX 79765

Claremore OK 74017

(918) 343-1191 or (800) 331-3916

Fax (918) 343-7304

(915) 563-2897 or (800) 733-0006

Fax (915) 563-4703

OREGON

**GAFFEY, INC.

**GENERAL TOOL & SUPPLY CO.

2705 N.W. Nicolai

1436 N. Duck Creek Road

Cleveland TX 77327

Portland OR 97210

(281) 443-6690 or (800) 233-8179

Fax (281) 592-6984

(503) 226-3411 or (800) 783-3411

Fax (503) 778-5518

**HYDRAULIC EQUIPMENT SER.

1021 N. San Jacinto Street

PENNSYLVANIA

**GLOBE ELECTRIC CO.

200 23rd Street

Houston TX 77002

(713) 228-4073 Fax (713) 228-0931

Pittsburgh PA 15215

(412) 781-2677 or (800) 850-4440

Fax (412) 781-1812

UTAH

**ROCKY MOUNTAIN WIRE ROPE & RIG.

2421 South 2570 West

Salt Lake City UT 84119

(801) 972-4972 or (800) 615-3193

Fax (801) 974-0621

*KEYSTONE CRANE & HOIST CO.

861 S. Washington Road

McMurray PA 15317

(724) 746-5080 Fax (724) 746-5082

VIRGINIA

**MCDAL CORP.

**FOLEY MATERIAL HANDLING CO.

11327 Va. Crane Drive

475 East Church Road

King of Prussia PA 19406

(610) 277-5484 or (800) 626-2325

Fax (610) 277-4690

Ashland VA 23005

(804) 798-1343 Fax (804) 798-7843

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road

Brookfield, Wisconsin 53005

TEL: (800) 729-3878

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

NEC Musical Toy Instrument IPK User Manual
NEC Server 320Ma User Manual
Nespresso Coffeemaker N9 User Manual
NETGEAR Network Router FVS328 User Manual
NeumannBerlin Microphone KM 56c User Manual
Olympus Camera Accessories BLM 1 User Manual
Onkyo Stereo Receiver TX L55 User Manual
Panasonic Blu ray Player DMP BD755 User Manual
Paradyne Network Card UIM 1000T User Manual
Patton electronic Surge Protector 515 DB 15 User Manual