Operating and installation instructions
Cooker hood
To prevent the risk of accidents or damage to the appliance, it is
essential to read these instructions before it is installed and used for
the first time.
en-GB
M.-Nr. 09 813 750
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Connection for air extraction.............................................................................. 46
Electrical connection........................................................................................... 49
Activating Con@ctivity 2.0................................................................................... 50
Activating the hob............................................................................................. 51
After Sales / Guarantee ....................................................................................... 52
Position of the data plate....................................................................................... 52
Technical data ...................................................................................................... 53
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
This appliance complies with all relevant local and national safety
requirements. Inappropriate use can, however, lead to personal
injury and damage to property.
To avoid the risk of accidents and damage to the appliance,
please read these instructions carefully before using it for the first
time. They contain important notes on the safety, installation, use
and maintenance of the appliance. Miele cannot be held liable for
non-compliance with these instructions.
Keep these instructions in a safe place and ensure that all users
are familiar with the contents. Pass them on to any future owner of
the appliance.
Correct application
This cooker hood is intended for use in domestic households and
similar working and residential environments.
The cooker hood is not intended for outdoor use.
It must only be used as a domestic appliance to extract vapours
and remove odours from cooking.
Any other usage is not supported by the manufacturer and could be
dangerous.
The cooker hood can only be used by people with reduced
physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised whilst using it, or have been
shown how to use it in a safe way and recognise and understand the
consequences of incorrect operation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Safety with children
Children under 8 years of age must be kept away from the cooker
hood unless they are constantly supervised.
Children 8 years and older may only use the cooker hood
unsupervised if they have been shown how to use it safely and
recognise and understand the consequences of incorrect operation.
Children must not be allowed to clean or maintain the cooker
hood unsupervised.
Please supervise children in the vicinity of the cooker hood and
do not let them play with it.
Danger of suffocation. Packaging, e.g. plastic wrappings, must be
kept out of the reach of babies and children. Whilst playing, children
could become entangled in packaging or pull it over their head and
suffocate.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Technical safety
Unauthorised installation, maintenance and repairs can cause
considerable danger for the user. Installation, maintenance and
repairs must only be carried out by a Miele authorised technician.
A damaged appliance can be dangerous. Check it for visible signs
of damage. Do not use a damaged appliance.
The electrical safety of this appliance can only be guaranteed
when correctly earthed. It is essential that this standard safety
requirement is met. If in any doubt please have the electrical
installation tested by a qualified electrician.
Reliable and safe operation of this cooker hood can only be
assured if it has been connected to the mains electricity supply.
Before connecting the appliance to the mains supply, ensure that
the connection data on the data plate (voltage and frequency) match
the mains electricity supply. This data must correspond in order to
avoid the risk of damage to the appliance. Consult a qualified
electrician if in any doubt.
Do not connect the appliance to the mains electricity supply by a
multi-socket unit or an extension lead. These are a fire hazard and
do not guarantee the required safety of the appliance.
For appliances with an external motor fitted (...EXT models) the
connection of the two units must be made using the connection
cable and the plug connectors.
These models may only be combined with a Miele external motor.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
For safety reasons, this appliance may only be used after it has
been built in.
The cooker hood must not be used in a non-stationary location
(e.g. on a ship).
Tampering with electrical connections or components and
mechanical parts is highly dangerous to the user and can cause
operational faults.
Only open the housing as described in the instructions given in the
installation sheet and in the Cleaning and care section of this
booklet. Under no circumstances should any other parts of the
housing be opened.
Miele can only guarantee the safety of the appliance when
genuine original Miele replacement parts are used. Faulty
components must only be replaced by Miele spare parts.
During installation, maintenance and repair work, the appliance
must be disconnected from the mains electricity supply.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Using at the same time as other heating appliances that depend on the air
from the room
Warning - danger of toxic fumes
Great care should be taken when using the cooker hood at the
same time and in the same room or area of the house as another
heating appliance which depends on the air in the room.
Such appliances include gas, oil, wood or coal-fired boilers and
heaters, continuous flow or other water heaters, gas hobs,
cookers or ovens which draw air in from the room and duct
exhaust gases out through a chimney or extraction ducting.
When used in extraction mode, with or without an external motor
fitted, or in recirculation mode with a recirculation box installed
outside the room, the appliance draws air in from the room in
which it is installed and from neighbouring rooms.
If there is insufficient air, an underpressure will occur. The heating
appliance will be starved of oxygen, impairing combustion.
Harmful gases could be drawn out of the chimney or extraction
ducting back into the room, with potentially fatal consequences.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
In order to ensure safe operation, and to prevent gases given off
by the heating appliances from being drawn back into the room
when the cooker hood and the heater are in operation
simultaneously, an underpressure in the room of 0.04 mbar (4 pa)
is the maximum permissible.
Ventilation can be maintained by air inlets which cannot be
blocked, in windows, doors or outside wall vents, or by other
technical measures, such as ensuring that the cooker hood can
only be switched on when the heating appliance is switched off or
vice versa. A ventilation brick alone is not generally sufficient to
ensure safe ventilation.
The overall ventilation condition of the dwelling must be taken into
account. If in any doubt, the advice of a competent builder or, for
gas a qualified gas fitter (registered with an official gas safety
body in accordance with national safety regulations, GasSafe in
the UK) must be sought.
If the cooker hood is used in recirculation mode, where the air is
directed back into the room in which it is located, operating a
heating appliance which depends on the room air at the same
time is no cause for concern.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Correct use
Never use a naked flame beneath the cooker hood. To avoid the
danger of fire, do not flambé or grill over a naked flame.
When switched on, the cooker hood could draw flames into the filter.
Fat deposits could ignite, presenting a fire hazard.
The cooker hood can become damaged when exposed to
excessive heat.
– When using the cooker hood over a gas hob, ensure that any
burners in use are always covered by a pan. Switch the cooking
zone off when a pan is removed, even for a short time.
– Select a pan which is suitable for the size of the burner.
– Regulate the flame so that it does not burn up the sides of the
pan.
– Avoid overheating the pan (e.g. when cooking with a wok).
Always switch the cooker hood on when a cooking zone is in use,
otherwise condensation may collect in the hood, which could cause
corrosion.
When cooking with oil or fat, chip pans and deep fat fryers etc, do
not leave the pans unattended. Never leave an open grill unattended
when grilling. Overheated oil and fat can ignite and could set the
cooker hood on fire.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Do not use the cooker hood without the filters in place. This way
you will avoid the risk of grease and dirt getting into the appliance
and hindering its smooth operation.
There is a risk of fire if the cooker hood is not cleaned as
described in these operating instructions.
The cooker hood can get very hot during cooking due to heat
rising from the hob.
Do not touch the housing or the grease filters until the cooker hood
has cooled down.
Correct installation
Refer to the cooker or hob manufacturer's instructions as to
whether a cooker hood may be operated above the cooker/hob.
Safety regulations prohibit the fitting of a cooker hood over solid
fuel stoves.
Insufficient distance between the cooker or hob and the cooker
hood can result in damage to the hood.
The minimum safety distances between the top of the cooker or hob
and the bottom of the cooker hood given in the "Installation" section
must be maintained, unless the hob manufacturer states that a
greater distance is required.
If more than one cooking appliance is fitted beneath the cooker
hood, and they have different minimum safety distances to the
cooker hood, select the greater distance.
The distances given in "Installation" must be observed when
fitting the cooker hood.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Metal parts can have sharp edges which may cause injury.
Wear gloves to protect your hands from being cut.
Exhaust ducting must be of non-inflammable material. Suitable
material is available from Miele specialist dealers or the Miele Spares
Dept.
The appliance must not be connected to a chimney or flue which
is in use. Neither should it be connected to ducting which ventilates
rooms with fireplaces.
If exhaust air is to be extracted into a chimney or ventilation duct
no longer used for other purposes, seek professional advice.
Cleaning and care
Do not use a steam cleaning appliance to clean this appliance.
The steam could reach electrical components and cause a short
circuit.
Accessories
Only use genuine original Miele accessories with this appliance.
Using accessories from other manufacturers will invalidate the
guarantee, and Miele cannot accept liability.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Disposal of your old appliance
Electrical and electronic appliances
often contain valuable materials. They
also contain materials which, if handled
or disposed of incorrectly, could be
potentially hazardous to human health
and to the environment. They are,
however, essential for the correct
functioning of your appliance. Please
do not therefore dispose of it with your
household waste.
Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also
reduces the amount of waste in landfill
sites.
Please dispose of it at your local
community waste collection / recycling
centre or contact your Dealer for
advice.
Ensure that it presents no danger to
children while being stored for disposal.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Modes of operation
Depending on the model of the cooker
hood, the following options are
available:
Recirculation mode
(requires purchase of conversion kit and
charcoal filter: see "Technical Data")
Extraction mode
The air is drawn in and cleaned first by
the grease filter and then by a charcoal
filter. The cleaned air is then
The air is drawn in and cleaned by the
grease filter and directed outside.
recirculated back into the kitchen.
Non-return flap
Operation with an external
motor
(...EXT model cooker hoods)
The non-return flap is designed to
prevent the exchange of room and
outside air taking place.
The flap is closed when the cooker
hood is switched off.
When the cooker hood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
A Miele extraction fan is installed in a
location of your choice outside the
room for cooker hoods which are
designed to be connected to an
external motor. The external motor is
connected to the cooker hood by
means of a control cable and is
operated by Con@ctivity 2.0 or by the
controls on the cooker hood.
If the on-site ventilation system does
not have a non-return flap, the non-
return flap supplied must be fitted in the
exhaust socket in the motor unit.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Modes of operation
The hob transmits information about its
operational status via a wireless signal
to the cooker hood.
Con@ctivity 2.0 function
Automatic control
The cooker hood has a communication
facility which enables the automatic
operation of the cooker hood
depending on the operational state of
the hob.
– When the hob is switched on, the
hob lighting comes on independently
and then after a short time the fan
also comes on.
– During cooking the cooker hood
automatically sets the power level
according to the number of cooking
zones in operation and their power
levels.
– After switching the hob off the fan
and the hob lighting will switch off
automatically after a specified period
of time.
See "Operation" for detailed
information about this function.
To make use of the communication
facility the hob must be fitted with a
Con@ctivity 2.0 Stick .
Refer to the installation instructions for
the Con@ctivity 2.0 Stick to check
whether it is compatible with your hob.
To use the Con@ctivity 2.0 function, a
wireless connection must be
established between the hob and the
cooker hood (see "Activating
Con@ctivity 2.0").
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
a
b
c
d
e
f
Telescopic extension piece
Tower
Canopy
Controls
Grease filter
Spacer frame
The spacer frame creates a shadow gap between the tower and the ceiling.
The cooker hood can be installed with or without the spacer frame.
g
Recirculation grilles
(only for recirculation mode)
h
i
Hob lighting
Charcoal filter
(special accessory for recirculation mode)
j
k
l
m
n
Control for the hob lighting
On/Off control for the fan
Controls to select the fan power level
Control for the run-on option
Operating hours control
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Automatic mode)
When Con@ctivity 2.0 is activated, the
cooker hood always works in automatic
mode (see "Activating Con@ctivity
2.0").
Reaction time
The cooker hood reacts with a slight
delay because altering the power level
on the hob does not immediately result
in a reduction or increase in cooking
vapours.
To operate the cooker hood manually,
see "Cooking without Con@ctivity 2.0".
Because the hob transmits the
information to the cooker hood at
intervals, this can also cause delays.
Cooking with Con@ctivity 2.0
(Automatic mode)
Switch a cooking zone on at the
power level you want.
The reaction can vary from a few
seconds to a couple of minutes.
The cooker hood lighting will come on.
After a few seconds the fan will come
on, first at power level 2, then it will
switch immediately to power level 1.
The cooker hood selects the power
level automatically during cooking.
This is determined by the total output of
the hob, i.e, the number of cooking
zones in operation and the power levels
selected.
If you select a higher power level or
are using several cooking zones, the
cooker hood will switch to a higher
power level.
When you reduce the power level or
the number of cooking zones on the
hob, the cooker hood power level is
also reduced.
Examples for power levels 1 to 4
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Automatic mode)
Cooking process
Switching off
If for example you switch on a
cooking zone at the highest power
level to heat a pan for frying and
reduce the power level after approx.
60 to 90 seconds*, a cooking process
is recognised (*60 seconds to 5
minutes for a HiLight hob).
Switch off all cooking zones.
The cooker hood fan will reduce its
power level over the next few minutes
and will eventually switch itself off.
This helps to neutralise any lingering
vapours and odours in the air.
The cooker hood switches itself on and – From the intensive setting 4, the fan
when the hob power level has been
reduced, the hood switches to power
level 3 and remains at that level for
approx. 5 minutes.
switches immediately to level 3.
– If the fan is operating at level 3, it will
switch to level 2 after approx. 1
minute.
After that the cooker hood power level
is determined automatically by the
Con@ctivity function.
– From level 2, the fan switches to level
1 after 2 minutes.
– After 2 minutes at level 1 the fan
switches itself off.
You can select another power level
manually before then.
– After another 30 seconds the lighting
switches off.
The cooking process is then finished.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Automatic mode)
Leaving automatic mode
temporarily
To leave automatic mode temporarily
during cooking:
Returning to automatic mode
The cooker hood returns to automatic
mode:
if the cooker hood has not been used
for approx. 5 minutes after selecting
a power level manually, or
Manually select a different power
level, or
if the manually selected fan power
level corresponds to the automatic
one again, or
Manually switch the cooker hood off,
or
Activate the run-on option on the
cooker hood. The fan will switch off
after the selected time and the
if the cooker hood fan and the hob
have been switched off for at least 30
seconds.
Automatic mode will resume next
time the hob is switched on.
lighting remains switched on.
The cooker hood can now be operated
manually (see "Cooking without
Con@ctivity 2.0").
If you wish to operate the cooker
hood manually for a complete
cooking process, switch on the
cooker hood fan before switching on
the hob.
If the cooker hood and the hob have
been switched off for at least 30
seconds after cooking, automatic
mode will resume the next time the
hob is switched on.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Manual mode)
After you have finished cooking,
press the run-on option control 5
15
Cooking without Con@ctivity
2.0 (Manual mode)
The cooker hood can be operated
manually if:
– Once: the fan will switch itself off
after 5 minutes (5 lights up).
– Con@ctivity 2.0 is not activated.
– Twice: the fan will switch itself off
– You have temporarily deactivated
Con@ctivity 2.0 (see "Leaving
automatic mode temporarily").
after 15 minutes (15 lights up).
– If you press the run-on option control
5 15 again, the fan will remain on
(5 15 will go out).
Switching the fan on
Press the On/Off control .
Switching the fan off
The fan will switch on at level 2. The
symbol and 2 will light up in the power
level display.
Use the On/Off control to switch
the fan off.
The symbol will go out.
Selecting the power level
For light to heavy cooking vapours and
odours, select from power levels 1 to 3.
When frying or cooking food with a very
strong aroma, select the Intensive
setting IS.
For a lower power level, press the
"" control, or "" for a higher level.
Reducing power on the intensive
setting
If Power management is activated
(default), the fan automatically switches
to level 3 after 5 minutes.
Selecting the run-on time
It is advisable to run the fan for a few
minutes after cooking has finished to
neutralise any lingering vapours and
odours in the air.
With the run-on option the fan switches
itself off automatically after a pre-
selected time.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Manual mode)
– the lighting button again.
Switching the hob lighting on /
off
The hob lighting can be switched on
and off independently of the fan.
If Power management is switched on,
the 1 and IS indicators will light up
constantly.
If it is switched off, 1 and IS will flash.
To do this, press .
Press "" to switch Power
management off.
The symbol will light up when the
hob lighting is switched on.
The 1 and IS indicators will flash.
Power management
To switch it on, press "".
The cooker hood features a power
management system to help save
energy. The fan power level is reduced
and the lighting is switched off
automatically.
The 1 and IS indicators will light up
constantly.
Confirm the setting with the run-on
option button 5 15.
All the indicator lamps will go out
– If the Intensive setting is selected,
the fan automatically switches to
level 3 after 5 minutes.
If you do not confirm within 4 minutes,
the cooker hood will revert to the old
setting.
– From levels 3, 2 or 1 the power will
be reduced by one level after 2 hours
and then in 30 minutes stages until
the fan finally switches off.
– The hob lighting will switch off
automatically after 12 hours.
Switching Power management on/off
You can deactivate Power
management.
This can result in increased electricity
consumption.
Switch off the fan and the lighting.
Press the run-on option button 5
15 for approx. 10 seconds, until 1
lights up in the power level display.
Then press in turn,
– the lighting button ,
– the "" button and then
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Automatic and Manual modes)
The grease filter symbol and one of
the fan power level indicators flash.
Operating hours counters
The number of hours the appliance has
been in operation is stored in memory.
Fan power level indicators 1 to IS show
the time set:
When the Grease filter symbol or the
Charcoal filter symbol lights up, the
operating hours counters are signalling
that the filters need to be cleaned or
changed. Further information about
cleaning and changing the filters and
resetting the operating hours counter
can be found under "Cleaning and
care".
1............................................... 20 hours
2............................................... 30 hours
3............................................... 40 hours
IS ............................................. 50 hours
Press the "" symbol for a shorter
operating time, or the "" symbol to
select a longer operating time.
Altering the operating hours counter
for the grease filters
Confirm the selection by pressing the
operating hours control .
You can set the operating hours
counter for the grease filters to suit the
type of cooking you do.
All the indicators will go out
If you do not confirm within 4 minutes,
the cooker hood will revert to the old
setting.
The grease filter operating hours
counter is set at the factory for 30
hours.
– Select a shorter time of 20 hours if
you roast or fry a lot.
– If you only cook occasionally we
recommend that you still select a
short time because grease which has
built up gradually over a long period
of time will harden on the filters and
make cleaning more difficult.
– Select a longer time of 40 or 50
hours if you use very little fat for
cooking.
Use the On/Off control to switch
the fan off.
Press the run-on control 515 and
the operating hours control at
the same time.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Automatic and Manual modes)
Activating and altering the charcoal
filter operating hours counter
Reading the filter operating hours
counter
The charcoal filter is needed for
recirculation mode.
To check the percentage of time set
already used
The operating hours counter for the
charcoal filter needs to be activated
once and the operating hours counter
needs to be set to suit the kind of
cooking you do:
Use the On/Off control to switch
the fan on.
Press and hold the operating hours
control
– Once, to read the Grease filter
operating hours. The grease filter
symbol lights up.
Use the On/Off control to switch
the fan off.
Press the "" symbol and the
operating hours control at the
same time.
– Twice, to read the Charcoal filter
operating hours. The Charcoal filter
symbol lights up.
The charcoal filter symbol and one
of the fan power levels will flash.
One or more of the power level
indicators will flash.
Fan power level indicators 1 to IS show
the time set:
The number of fan power level
indicators flashing shows the
1............................................. 120 hours percentage of the operating time which
has already been used up.
2............................................. 180 hours
1 ................................................... 25 %
3............................................. 240 hours
1 and 2 ......................................... 50 %
IS ........................................ Deactivated
1 to 3 ............................................ 75 %
Press the "" symbol for a shorter
operating time, or the "" symbol to
1 to IS ......................................... 100 %
select a longer operating time.
The number of operating hours used
remains in the memory, even when
the appliance is switched off or there
is a power cut.
Confirm the selection by pressing the
operating hours control .
All the indicator lamps will go out.
If you do not confirm within 4 minutes,
the cooker hood will revert to the old
setting.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy saving tips
This cooker hood operates very
efficiently and economically. The
following will help you to save even
more energy when using it:
– Make sure that you switch the
cooker hood off after use.
If cooking vapours and odours still
need to be removed from the
kitchen air after cooking, use the
run-on function. The fan will
switch off automatically after the
selected run-on time.
– Ensure that there is sufficient
ventilation in the kitchen when
cooking. In extraction mode, if there
is insufficient air flow the cooker
hood cannot operate efficiently and
this causes increased operating
noise levels.
– Clean or change the filters at regular
intervals. Heavily soiled filters reduce
performance, increase the risk of fire
and are unhygienic.
– Always cook with the lowest possible
setting. This produces fewer cooking
vapours, so you can use a lower
cooker hood power level and
therefore benefit from reduced
energy consumption.
– Use the Con@ctivity function. The
cooker hood will switch on and off
automatically at the optimum power
level for the cooking you are doing,
which ensures low energy
consumption.
– If you are operating the cooker hood
manually, please note the following:
– Check the power level selected on
the cooker hood. A lower power
level is generally sufficient for the
majority of cooking. Only use the
intensive setting when necessary.
– When a large volume of cooking
vapours are being produced,
switch to a high power level in
good time. This is more efficient
than operating the cooker hood for
longer to try to capture cooking
vapours which have already been
distributed throughout the kitchen.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Important for appliances with
stainless steel surfaces
Casing
General information
(This information does not apply to the
controls).
The surfaces and controls are
susceptible to scratches and
abrasion.
Please observe the following
cleaning instructions.
Stainless steel surfaces can be
cleaned with a proprietary non-
abrasive cleaning agent designed
specifically for use on stainless steel.
To help prevent re-soiling, a
proprietary conditioning agent for
stainless steel (available from Miele)
can also be used. Follow the
manufacturer’s instructions on the
packaging.
All external surfaces and controls can
be cleaned using hot water with a
small amount of washing-up liquid
applied with a well wrung-out soft
sponge or cloth.
Do not let moisture get into the
cooker hood.
Only use a damp cloth when
cleaning. This is particularly
important around the controls.
Important for RAL coloured housing
(Special order finish)
Please observe the general notes on
cleaning earlier in this section.
After cleaning, wipe the surfaces dry
It is very difficult to clean this type of
surface without causing minor marks
to the surface material. This can
become particularly noticeable
depending on the type of lighting in
the kitchen.
using a soft cloth.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents. These will damage
the surface material.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Important for the controls
Grease filter
The re-usable metal grease filter in the
appliance removes solid particles from
the kitchen vapours (grease, dust, etc)
preventing soiling of the cooker hood.
Do not leave soiling on the controls
for any length of time.
Otherwise they may suffer
discolouration or damage.
Remove soiling straight away.
An oversaturated filter is a fire
hazard.
Please observe the general notes on
cleaning earlier in this section.
Cleaning interval
Do not use stainless steel cleaning
agents on the controls.
Grease which is left to accumulate over
time will harden and become difficult to
remove. The grease filter should
therefore be cleaned at least every 3 - 4
weeks.
Important for appliances with glass
surfaces
Glass surfaces can be cleaned using
a proprietary non-abrasive cleaning
agent designed specifically for use
on glass.
The operating hours counter reminds
you to clean the filter regularly. The
grease filter symbol will light up.
You can set the operating hours
counter for the grease filter to suit the
type of cooking you do (see
"Operation").
Removing a grease filter
The grease filter can fall out when
you are handling it.
This can result in damage to the filter
and the hob below.
Make sure you hold the filter
securely at all times when handling
it.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
To take out a grease filter, release the Cleaning the grease filter in a
locking clip on the filter, lower the
filter approx. 45°, unhook it at the
back and remove it.
dishwasher
Place the filter as upright as possible
in the lower basket, or at an angle,
ensuring the spray arm is not
obstructed.
Cleaning the grease filter by hand
Clean the filter with a soft nylon brush
in a mild solution of hot water and a
small amount of washing-up liquid.
Do not use "neat" washing up liquid.
Use a proprietary household
dishwasher detergent.
Select a dishwasher programme with
a wash temperature between 50°C
and 65°C.
Unsuitable cleaning agents
Unsuitable cleaning agents can cause
damage to the surface of the filters if
used regularly.
Depending on the cleaning agent
used, cleaning a filter in a dishwasher
can cause permanent discolouration
to internal surfaces. However, this will
not affect the functioning of the filter
in any way.
Do not use:
– cleaning agents containing descaling
agents
– powder cleaners, cream cleaners
After cleaning
– aggressive multi-purpose cleaning
agents or spray cleaners for grease
After cleaning, leave the filter to dry
on an absorbent surface before
replacing it.
– oven sprays
When removing the filter for cleaning,
also clean off any residues of oil or
fat from the now accessible casing to
prevent the risk of these catching fire.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Replace the grease filter, making sure
that the locking clip is facing
outwards.
Charcoal filter
If the cooker hood is connected for
recirculation, a charcoal filter must be
inserted in addition to the grease filter.
This is designed to absorb cooking
odours.
It is fitted in the canopy above the
grease filter.
Replacement charcoal filters can be
obtained from your Miele retailer or via
See back of manual for contact details,
and "Technical data" for type and
reference number.
If the grease filter is inadvertently
replaced the wrong way round, insert
a small screwdriver blade into the slit
to disengage the clip.
Fitting/replacing a charcoal filter
Resetting the grease filter operating
hours counter
Before fitting or replacing the
charcoal filter, the grease filter must
first be taken out (see previous
section for instructions on how to do
this).
After cleaning, the operating hours
counter needs to be re-set.
Whilst the fan is switched on, press
the operating hours control for
approx. 3 seconds, until only the 1 is
flashing.
Take the charcoal filter out of its
packaging.
The grease filter symbol goes out.
If you want to clean the grease filter(s)
before the operating hours counter has
reached its maximum,
Press the operating hours control
for approx. 6 seconds, until only
the 1 is flashing.
Press the charcoal filter into the
frame.
Replace the grease filter.
When fitting for the first time, activate
the operating hours counter (see
"Operation").
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
When to change the charcoal filter
Always replace the charcoal filter
when it no longer absorbs kitchen
odours effectively.
It should, however be replaced at
least every 6 months.
The charcoal filter operating hours
symbol will light up to remind you to
change the charcoal filter regularly.
The charcoal filter operating hours
counter needs to be activated before
using for the first time (see
"Operation").
Resetting the charcoal filter
operating hours counter
After changing the charcoal filter, the
operating hours counter needs to be re-
set.
To do this, with the fan switched on,
press the operating hours control
once, then press it again and
hold it for approx. 3 seconds until
only the 1 is flashing. The charcoal
filter symbol will go out.
If you want to clean the charcoal filter
before the operating hours counter has
reached its maximum:
Press the operating hours control
once, then press it again and
hold it for approx. 6 seconds until
only the 1 is flashing.
Disposing of the charcoal filter
Used charcoal filters can be disposed
of with the normal household waste.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Before installation
Before installation, it is important
to read the information given on the
following pages as well as the
"Warning and Safety instructions" at
the beginning of this booklet.
4 extension piece holders
for aligning and securing the telescopic
extension piece
Assembly parts
4 screws M4 x 8.5 mm
for securing the extension piece
holders
4 screws, 7 x 110 mm and
14 screws M4 x 8 mm
for securing the spacer frame and
securing the cooker hood to the
installation frame
4 plugs, 10 x 80 mm
for securing the cooker hood to the
ceiling
1 screw M4 x 12 mm
for securing the tower
The plugs meet European technical
requirements for use in concrete
ceilings.
They must only be used together
with 7 x 110 mm screws. For other
types of ceiling construction,
alternative fixings will be required.
Make sure the ceiling is able to take
the weight of the cooker hood.
DUI 32 conversion kit for
recirculation mode
(not supplied, available as an optional
accessory). The kit includes a
directional unit, aluminium hose and
hose clips.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
a
Installation area: cut-out for feeding
through the exhaust ducting, the
mains cable and with ...EXT models,
the connection cable to the external
motor. In recirculation mode, only
the mains cable is required.
Appliance dimensions
b
c
d
e
f
Possible height range for appliance
in extraction mode
Possible height range for appliance
in recirculation mode
Alternative installation with spacer
frame
Ventilation grille positioned at the
top for recirculation
A mains connection cable is
required to connect the cooker hood
to the socket in the ceiling. With air
extraction mode flexible ducting is
also required.
Exhaust connection 150 mm
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Safety distance between hob and cooker hood (S)
When planning the installation height of your cooker hood, the minimum safety
distance between the top of a cooker or hob and the bottom of the cooker
hood is as follows, unless a greater distance is specified by the manufacturer of
your cooking appliance.
See "Warning and Safety" instructions for further information.
Cooking appliance
Minimum distance S
450 mm
Electric hob
Electric grill, deep fat fryer (electric)
650 mm
Multi-burner gas hob,
650 mm
total output ≤ 12.6 kW, no burner > 4.5 kW
Multi-burner gas hob,
760 mm
total output > 12.6 kW and ≤ 21.6 kW,
no burner > 4.8 kW.
Multi-burner gas hob,
Not possible
total output > 21.6 kW,
or multi-burner gas hob where one burner > 4.8 kW.
Single burner gas hob, output ≤ 6 kW.
650 mm
760 mm
Single burner gas hob, output > 6 kW and ≤ 8.1 kW.
Single burner gas hob, output > 8.1 kW
Not possible
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation recommendations
– When deciding on the safety
distance between the hob and
cooker hood, please note that a
distance of 650 mm above electric
cookers/hobs may be preferable to
give more working space under the
hood.
– Account should also be taken of the
height of the person who will be
using the hood most often. They
should have sufficient space to work
comfortably at the hob, and be able
to reach the hood controls with ease.
– Please be aware that if positioned
too high, extraction will be inefficient.
– To achieve optimum vapour
extraction, the cooker hood must
cover the hob. It should be
positioned centrally over the hob, not
to the side or to the back of it.
– The hob should be no wider than the
cooker hood, and if possible, it
should be narrower.
– The installation area must be easily
accessible. The cooker hood should
be easily accessible and easy to
dismantle in the event that service is
required. This should be taken into
consideration when planning the
position of cupboards, shelves,
ceilings or features in the vicinity of
the cooker hood.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Protective foil
The housing components have
protective foil around them to protect
them from transport damage.
Please remove this foil before fitting
the housing components. It can be
peeled off easily.
With air extraction mode:
– Place a section of the exhaust
ducting in the ceiling and feed it
down through the cross-sectional
area as illustrated. Exhaust ducting of
approx. 700 mm length is required
between the ceiling and the cooker
hood exhaust socket.
– Secure the exhaust ducting to the
exhaust socket, e.g. with a hose clip
(available as an optional accessory)
on flexible ducting.
Place the mains cable and for ...EXT
models, the connection cable to the
external motor in the ceiling and
guide them through the ceiling in the
area shown. A mains cable of approx.
700 mm in length is required between
the ceiling and the cooker hood
connectors.
Draw two intersecting lines on the
ceiling.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Use a knife to release the four
spacers and the two covers from the
spacer frame supplied.
Drill four holes 10 mm, approx. 115
mm deep for the plugs supplied.
Place the four plugs in the holes and
screw in the 4 screws so that they
protrude by approx. 30 mm.
Use the space frame as a drilling
template. Place it on the ceiling with
the arrows pointing forwards. Using
the notches, align the spacer frame
on the intersecting lines and make
pencil marks for the drill holes.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The spacer frame can be installed
between the tower and the ceiling. This
creates a shadow which gives the
illusion of a gap between the ceiling
and the tower. This is useful if the
ceiling is not level or is uneven. The
cooker hood is aligned vertically with
the spacers supplied. Visual
Mount the spacer frame onto the
installation frame.
irregularities between the tower and the
ceiling are then concealed by the
shadow.
If you wish to install the cooker hood
with the spacer frame, remove the
four inserts from the fixing holes.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Hang the installation frame on the
four screws. The front of the frame is
marked with a "V".
Align the installation frame with the
intersecting lines and secure it with
the screws.
The spacers, which were removed
from the spacer frame at the start,
can be used to align the cooker hood
vertically.
If using the spacer frame, place the
two covers into the fixing holes.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Holding the installation frame
securely, remove the two fixing
screws and extend the installation
frame to its maximum length.
Replace the screws.
The directional unit from conversion kit
DUI 32 (optional accessory) is installed
for recirculation mode (UL):
Bend the four retaining tabs on the
installation frame outwards.
Fit the directional unit as shown,
noting the marking on the front.
Place the mains cable inside the
installation frame.
Bend the retaining tabs back and
approx. 45° inwards to hold the
directional unit in place.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Secure the exhaust socket to the
hose using a hose clip.
Secure the hose to the directional
unit socket using a hose clip.
Check that the hose is held securely.
Push the telescopic piece over the
installation frame:
– with the recirculation grilles at the
bottom for air extraction mode (AL)/
external motor (EXT),
– with the recirculation grilles at the top
for recirculation mode (UL).
Bend the two retaining tabs outwards
to prevent the telescopic piece from
slipping down again.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Fit the four telescopic piece clamps.
When the screws are tightened, the
clamps spread out and push the
telescopic piece upwards.
Bend back the two retaining tabs.
Push the tower over the telescopic
piece and bend the retaining tabs
outwards again to prevent the tower
from slipping down again.
Tighten the screws only until the top
edge of the telescopic piece is
evenly aligned with the ceiling or the
spacer frame.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
A non-return flap is supplied with the
cooker hood or is already fitted in the
exhaust socket (depending on cooker
hood version).
With extraction mode / external motor
(AL, EXT) fit the non-return flap in the
exhaust socket if your ducting
system is not equipped with one.
Recirculation mode (UL) does not
require the non-return flap to be
fitted. If there is one present, it should
be removed.
Hang the cooker hood on the
brackets, making sure that the
controls are at the front.
Secure the cooker hood with the
screws supplied.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
For ...EXT models only: Connect the
cooker hood and the external motor
using the connection cable.
Connect the mains cable. See
"Electrical connection".
Unscrew both screws from the
installation frame again.
The canopy can now be adjusted to the
desired height, observing the
permissible height ranges:
Place the exhaust ducting onto the
exhaust socket.
– With extraction mode: upwards as far
as it will go, downwards as far as the
mark beneath the "A".
– With recirculation mode: upwards as
far as the "U", downwards as far as it
will go.
Follow the instructions in "Appliance
dimensions". Safety distances
between the hob and cooker hood
must be observed.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Raise the canopy to the desired
height and secure it wtih the screws.
Hold the tower securely, bend back
the retaining tabs and carefully lower
the tower.
The tower will locate in the cut-out in
the canopy.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
With recirculation mode (UL) cooker
hoods, insert the charcoal filter.
Remove the grease filter from the
cooker hood.
Insert the safety screw on the inside.
Carefully remove the protective foil
from the grease filter.
Replace the grease filter.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection for air extraction
– Ensure that all connections are
strong and airtight.
If this cooker hood is used at the
same time as a heating appliance
that relies on oxygen from the same
room there is a risk in certain
circumstances of toxic fumes
building up.
Remember that any constriction of
the air flow will reduce extraction
performance and increase operating
noise.
It is essential that the "Warning and
Safety" instructions are observed.
The cooker hood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
If the exhaust is ducted through an
outside wall, a telescopic wall vent or
a roof vent (available as an optional
accessory) is recommended.
Use smooth or flexible ducting made
from approved non-flammable
materials for exhaust ducting.
When using an external motor, make
sure that the exhaust ducting is
sufficiently rigid. The external motor
can cause an underpressure which
can result in the exhaust ducting
distorting.
If the exhaust air is to be ducted into
a flue, the ducting must be directed
in the flow direction of the flue.
When ducting is horizontal it must be
laid to slope away at at least 1 cm
per metre. This is to ensure that
condensate cannot drain back into
the appliance.
To achieve the most efficient air
extraction with the lowest noise
levels, please note the following:
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 150 mm.
If the exhaust ducting is to run
through rooms, ceiling space etc.
where there may be great variations
in temperature between the different
areas, the problem of condensation
will need to be addressed. The
exhaust ducting will need to be
suitably insulated.
– If flat ducting is being used, the cross
section must not be smaller than the
cross sectional area of the exhaust
socket.
– The exhaust ducting should be as
short and straight as possible.
– Only use wide radius bends.
– The exhaust ducting must not be
kinked or compressed.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection for air extraction
Condensate trap
Silencer
To achieve even further reductions in
noise levels, a special silencer (optional
accessory) can be fitted in the ducting
system.
In addition to insulating the exhaust
ducting, we recommend that a suitable
condensate trap is also installed to
collect and evaporate any condensate
which may occur.
Extraction mode
Condensate traps for 125 mm or 150
mm ducting are available as optional
accessories.
When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust socket.
The arrow on the housing indicates
the direction of air-flow.
The silencer not only reduces noise
from the motor outside the house, but
also sounds from outside (e.g. traffic
noise). For this reason the silencer must
be positioned as close as possible to
the ducting exit .
A condensate trap is integrated in
cooker hoods which are designed for
connection to an external motor
(model......EXT).
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection for air extraction
Extraction mode with external motor
To minimise noise from the motor in the
kitchen, the silencer should be
positioned in front of the external motor
if possible, or, if the ducting is long,
above the exhaust socket on the
cooker hood . In the case of an
external motor located inside the
house, fitting a silencer behind the
external motor reduces the noise of
the motor outside the house.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
If the switch is not accessible after
installation (depending on country), an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD). Contact a
qualified electrician for advice.
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national and
local safety regulations (BS 7671 in
the UK).
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
Important
manufacturer cannot be held liable.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
This appliance is supplied for
connection to an a.c. 230 V single
phase 50 Hz supply. The wires in the
mains lead are coloured in accordance
with the following code:
Green/yellow ..................................earth
Blue..............................................neutral
Brown................................................live
The connection data is given on the
data plate. This is visible when the
grease filters have been removed.
Ensure that this data matches the
household mains supply.
WARNING:
THIS APPLIANCE MUST BE
EARTHED
If a flexible connection cable is being
used to connect the appliance to the
Connection of this appliance should be
made via a suitable isolator or a double electricity supply, the cross-sectional
pole fused spur connection unit which
complies with national and local safety
regulations and the On/Off switch
should be easily accessible after the
appliance has been built in. When
switched off there must be an all-pole
contact gap of 3 mm in the switch
(including switch, fuses and relays
according to EN 60335).
area of the the individual leads must be
between 0.75 mm² and 1.5 mm².
The strain relief must be used to ensure
problem-free connection.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Activating Con@ctivity 2.0
Activating the cooker hood
Installing the Con@ctivity 2.0
Stick
In order to use the Con@ctivity 2.0
function, the hob must first be fitted
with the Con@ctivity 2.0 Stick.
The hob and cooker hood must be
switched off.
Press the run-on option button 515
for approx. 10 seconds until the
indicator for power level 1 lights up.
Please read the separate installation
instructions supplied with the
Con@ctivity 2.0 Stick.
Then press in turn,
– the "" button,
Activating Con@ctivity 2.0
– then the "" button,
– then the lighting button .
Wireless connection must be activated
between the hob and the cooker hood
before the Con@ctivity 2.0 function can
be used.
The cooker hood is now in signing
on/off mode.
If a wireless connection has not yet
been established 2 and 3 will flash at
the same time.
If a wireless connection has already
been established, 2 and 3 will light up
constantly (Con@ctivity 2.0 is already
activated or a remote control is signed
on).
Both appliances must be installed and
operational.
Wireless connection must be activated
on the cooker hood and the hob at the
same time. Activation on the cooker
hood is described below.
Activation on the hob is described in
the relevant Operating and installation
instructions. Please refer to the
Operating instructions before starting.
Activate the cooker hood first, then the
hob.
To activate Con@ctivity 2.0, press the
"" button.
The search for a signal will start.
Meanwhile, start activating the hob.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Activating Con@ctivity 2.0
Activating the hob
Activation failed
While the cooker hood is searching
for a signal, start activating the hob.
More information about this can be
found in the Operating instructions
for the hob.
If connection cannot be established
despite activating the Con@ctivity
function on the cooker hood and
hob, the function must be
deactivated on both appliances and
then the procedure repeated.
When the hob registers that
connection has been established,
confirm activation on the cooker
hood with the run-on option control
515. All indicators will go out.
Deactivating Con@ctivity 2.0
Deactivation on the cooker hood is
carried out in the same way as
activation, by selecting "" instead
of "".
Confirm activation on the hob.
Con@ctivity 2.0 is now ready to use.
To deactivate the hob, please refer to
the Operating instructions supplied
with it.
If you do not confirm within 4 minutes,
activation will not take place.
Please bear in mind that disabling the
signal will also disable any remote
control function and this will have to
be activated again.
You only need to carry out the
activation procedure once. If the
appliances are disconnected from the
electricity supply, during a power cut
for example, they will still remain
activated.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales / Guarantee
In the event of a fault which you cannot
remedy yourself, please contact your
Miele dealer or the Miele Service
Department.
Contact details for Miele are given at
the back of this manual. N.B. A call-out
charge will be applied to service visits
where the problem could have been
resolved as described in these
instructions.
When contacting your dealer or Miele,
please quote the model and serial
number of your appliance.
These are shown on the data plate.
Position of the data plate
The data plate is visible after removing
the grease filters.
Guarantee: U.K.
In the U.K., the appliance is guaranteed
for 2 years from the date of purchase.
However, you must activate your cover
by calling 0330 160 6640 or registering
Guarantee: Other countries
For information on the appliance
guarantee specific to your country
please contact Miele. See end of this
booklet for contact details.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Fan motor*
200 W
4 x 3 W
Hob lighting
Total connected load*
Voltage, frequency
Fuse rating
212 W
AC 230 V, 50 Hz
5 A
Weight
DA 5106 D
41 kg
38 kg
DA 5106 D EXT
* For EXT models, the connected load and extraction power will depend on the type of
external motor fitted.
Length of connection cable to external motor: 1.9 m
Recirculation mode with conversion kit DUI 32 and charcoal filter DKF 12 (optional
accessories)
Conformity declaration
Miele hereby declares that the cooker hoods listed at the end of this booklet
comply with the basic requirements and other relevant regulations of Guideline
1999/5/EC.
A copy of the full Declaration of Conformity can be obtained from the address at
the end of this booklet.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Data sheet for domestic cooker hoods
In acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.
66/2014
MIELE
Model name / identifier
DA 5106 D
Annual Energy Consumption (AEChood
)
96,8 kWh/year
Energy efficiency class
A+ (most efficient) to F (least efficient)
Energy efficiency index (EEIhood
C
)
79,0
18,9
Fluid Dynamic Efficiency (FDEhood
)
Fluid Dynamic Efficiency class
A (most efficient) to G (least efficient)
C
Lighting Efficiency (LEhood
)
37,5 lx/W
Lighting Efficiency class
A (most efficient) to G (least efficient)
Grease Filtering Efficiency
A
92,1 %
Grease Filtering Efficiency class
A (most efficient) to G (least efficient)
Airflow at best efficiency point
B
3
360,4 m /h
Air flow (min. speed)
3
160 m /h
Air flow (max. speed)
3
450 m /h
Air flow (intensive or boost setting)
3
620 m /h
Max. air flow (Qmax
)
3
620 m /h
Air pressure at best efficiency point
346 Pa
40 dB
Airborne acoustical A-weighted sound power emissions (min. speed)
Airborne acoustical A-weighted sound power emissions (max. speed) 57 dB
Airborne acoustical A-weighted sound power emissions (intensive or
boost setting)
66 dB
Electrical power input at best efficiency point
Power consumption in off mode (Po)
183,0 W
W
Power consumption in standby mode (Ps)
Nominal power of lighting system
0,15 W
12,0 W
450 Ix
1,3
Average illumination of the lighting system on the cooking surface
Time increase factor
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Data sheet for domestic cooker hoods
In acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.
66/2014
MIELE
Model name / identifier
DA 5106 D EXT
8,8 kWh/year
Annual Energy Consumption (AEChood
)
Energy efficiency class
A+ (most efficient) to F (least efficient)
Energy efficiency index (EEIhood
A+
)
40,0
Fluid Dynamic Efficiency (FDEhood
)
Fluid Dynamic Efficiency class
A (most efficient) to G (least efficient)
-
Lighting Efficiency (LEhood
)
37,5 lx/W
Lighting Efficiency class
A (most efficient) to G (least efficient)
Grease Filtering Efficiency
A
%
Grease Filtering Efficiency class
A (most efficient) to G (least efficient)
Airflow at best efficiency point
-
3
m /h
Air flow (min. speed)
3
m /h
Air flow (max. speed)
3
m /h
Air flow (intensive or boost setting)
3
m /h
Max. air flow (Qmax
)
3
m /h
Air pressure at best efficiency point
Pa
Airborne acoustical A-weighted sound power emissions (min. speed)
dB
Airborne acoustical A-weighted sound power emissions (max. speed) 0 dB
Airborne acoustical A-weighted sound power emissions (intensive or
boost setting)
dB
Electrical power input at best efficiency point
Power consumption in off mode (Po)
W
W
Power consumption in standby mode (Ps)
Nominal power of lighting system
0,15 W
12,0 W
450 Ix
Average illumination of the lighting system on the cooking surface
Time increase factor
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
United Kingdom
Miele Co. Ltd.
Fairacres, Marcham Road
Abingdon, Oxon, OX14 1TW
Customer Contact Centre Tel: 0330 160 6600
E-mail: [email protected]
Malaysia
Miele Sdn Bhd
Suite 12-2, Level 12
Menara Sapura Kencana Petroleum
Solaris Dutamas No. 1, Jalan Dutamas 1
50480 Kuala Lumpur, Malaysia
Phone: +603-6209-0288
Fax: +603-6205-3768
Australia
Miele Australia Pty. Ltd.
ACN 005 635 398
ABN 96 005 635 398
1 Gilbert Park Drive, Knoxfield, VIC 3180
Tel: 1300 464 353
New Zealand
Miele New Zealand Limited
IRD 98 463 631
China
Level 2, 10 College Hill
Freemans Bay, Auckland 1011, NZ
Tel: 0800 464 353
Miele (Shanghai) Trading Ltd.
1-3 Floor, No. 82 Shi Men Yi Road
Jing' an District
200040 Shanghai, PRC
Tel: +86 21 6157 3500, Fax: +86 21 6157 3511
Singapore
Miele Pte. Ltd.
163 Penang Road
# 04 - 03 Winsland House II
Singapore 238463
Tel: +65 6735 1191, Fax: +65 6735 1161
E-Mail: [email protected]
Miele (Hong Kong) Limited
41/F - 4101, Manhattan Place
23 Wang Tai Road
Kowloon Bay, Hong Kong
Tel: (852) 2610 1331, Fax: (852)2610 1013
Email: [email protected]
South Africa
Miele (Pty) Ltd
India
63 Peter Place, Bryanston 2194
P.O. Box 69434, Bryanston 2021
Tel: (011) 875 9000, Fax: (011) 875 9035
E-mail: [email protected]
Miele India Pvt. Ltd.
Ground Floor, Copia Corporate Suites
Plot No. 9, Jasola
New Delhi - 110025
Tel: 011-46 900 000, Fax: 011-46 900 001
United Arab Emirates
Miele Appliances Ltd.
P.O. Box 11 47 82
Gold & Diamond Park, Sheikh Zayed Road
Building 6 / Offices Nos. 6-214 to 6-220
Dubai
Tel: +971-4-341 84 44
Fax: +971-4-341 88 52
E-Mail: [email protected]
Ireland
Miele Ireland Ltd.
2024 Bianconi Avenue
Citywest Business Campus, Dublin 24
Tel: (01) 461 07 10, Fax: (01) 461 07 97
Manufacturer: Miele & Cie. KG
Carl-Miele-Straße 29, 33332 Gütersloh, Germany
56
Download from Www.Somanuals.com. All Manuals Search And Download.
DA 5106 D
DA 5106 D EXT
en-GB
M.-Nr. 09 813 750 / 02
Download from Www.Somanuals.com. All Manuals Search And Download.
|
