Installation instructions
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
KFNS 37432 iD
To prevent accidents and machine damage
read these instructions before installation or use.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
,Failure to follow these
instructions can result in death, fire,
or electrical shock.
,Electrocution hazard
Electrical grounding required. This
appliance is equipped with a
three-prong (grounding) polarized
plug for your protection against
possible shock hazards.
Improper connection of the
equipment grounding conductor
may result in electric shock.
If you are in any doubt as to whether
the appliance has been properly
grounded, have the appliance
checked by a qualified electrician or
service technician.
Do not remove the round grounding
prong from the plug.
Do not use a two-prong grounding
adapter.
Do not use extension cords or
ungrounded (two prong) adapters.
Connect this appliance to a 110 –
120 VAC, 60 Hz and 15 amp (20 amp
for side-by-side) circuit (20 amp for
side-by-side) with a circuit breaker or
fuse.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer will
not be held responsible for damage
or injury arising from unauthorized
work.
This appliance should have its own
separate grounded circuit.
Before installing the appliance,
verify that the voltage, load and
circuit rating information found on
the data plate match the household
electrical supply.
The power cord is equipped with a
three-prong (grounding) plug for your
protection against potential electrical
shock. To maintain this protection:
– Do not modify the plug by removing
the round grounding prong.
,Do not ground to a gas pipe.
Check with a qualified elictrician if
you are not sure the appliance is
properly grounded. Do not have a
fuse in the neutral or grounding
curcuit.
– Do not use a two-prong adapter.
Where a two-prong wall outlet is
encountered, contact a qualified
electrician and have it replaced with
a three-prong outlet in accordance
with the local electrical codes and
regulations.
– Do not use a power cord that is
frayed or damaged.
– Do not connect the appliance using
an extension cord or extension
socket.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
The appliance must be connected to an Do not use an extension cord to
electrical outlet that is properly
grounded. The electrical installation
must comply with the applicable
electrical code.
connect the appliance to the power
supply. Extension cords do not
guarantee the required safety of the
appliance (e.g. they pose a danger of
overheating).
The outlet must be easily accessible
and not concealed behind the
Do not connect the appliance to
stand-alone inverters, such as those
used with an autonomous energy
source, e.g. solar power systems.
Otherwise, when the appliance is
switched on, peak loads in the system
can cause the safety shutdown
mechanism to be triggered. This can
damage electronic units.
appliance so that the appliance can
quickly be disconnected from the
electricity supply in an emergency.
The plug and power cable must not
come into contact with the back of the
appliance, as they could be damaged
by vibrations from the appliance. This
may result in a short circuit.
In addition, the appliance must not be
used with energy-saving devices,
which reduce the amount of energy
supplied to the appliance and cause it
to overheat.
In addition, no other appliances should
be plugged into a socket located
directly behind this appliance.
If the power cable needs to be
replaced, this work must only be
performed by a qualified electrician.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation information
Location
Safe operation of the appliance is
only assured if it has been installed
and connected in accordance with
these operating and installation
instructions.
This appliance should not be installed
near windows where it is exposed to
direct sunlight or directly adjacent to
heat-producing appliances such as an
oven or a radiator. The higher the room
temperature, the longer the compressor
runs, increasing energy consumption
by the appliance. Install the appliance
in a dry, well-ventilated room.
WARNING!
Danger of tilting! To avoid a hazard
due to instability of the appliance, it
must be fixde in accordance with
the instructions.
When installing the appliance, please
also note the following:
– The power outlet must not be located
directly behind the appliance and
must be easily accessible in an
emergency.
Side-by-side
The KFNS 37432 iD has two side-wall
heaters encased in foam and can be
built into separate cabinet units
arranged side-by-side with all
appliances.
– The plug and power cable must not
come into contact with the back of the
appliance, as they could be damaged
by vibrations from the appliance.
Please contact your dealer for
specific information about which
combinations will work with your
appliance.
– In addition, no other appliances
should be plugged into a socket
located directly behind this appliance.
Important! In environments with
high humidity condensation can
build up on the appliance exterior
and ultimately cause corrosion on the
outer walls.
To prevent this from happening, we
recommend installing the appliance
in a dry and/or an air-conditioned
room with sufficient ventilation.
Once you have completed the
installation, please make sure that the
appliance doors close properly, that the
ventilation openings are not covered
and that the appliance has been
installed as described in this chapter.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation information
Climate class
sufficient space for ventilation (see
"Installation dimensions"):
The appliance is designed for use
within a certain climate class (room
temperature) and should not be used
outside this range. The climate class for
your appliance is stated on the data
plate inside the appliance.
Climate class
Room temperature
SN
N
+10 °C to +32 °C
+16 °C to +32 °C
+16 °C to +38 °C
+16 °C to +43 °C
ST
T
Operation in a room which is too cold
will cause the compressor to switch off
for too long. This may result in increased
temperatures inside the appliance and
can cause the food to spoil.
– Air intake a occurs via the plinth at
the bottom of the appliance and the
air escapes at the top b at the back
of the cabinet.
Ventilation
WARNING! Danger of damage from
overheating. May restrict operation.
Keep ventilation openings, in the
appliance enclosure or in the built-in
structure, clear of obstruction.
– A ventilation gap at least 1,6'' (40
mm) deep must be provided behind
the appliance for air to circulate.
– The size of the ventilation openings in
the plinth, cabinet unit and above the
appliance must always be at least 78
3/4 in2 (200 cm2) to ensure that warm
air can escape without a problem.
The size of the ventilation gaps
indicated below must be observed,
otherwise the compressor will run
more frequently and for longer
periods of time. This will result in
increased energy consumption and
a higher operating temperature for
the compressor. This may, in turn,
damage the compressor.
– Important! The wider the ventilation
openings, the less energy used by
the appliance during operation.
The ventilation openings must not
be covered or blocked in any way.
They should also be dusted on a
regular basis.
The air at the back of the appliance
gets warm. The cabinet unit must
therefore be constructed to allow
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation information
Top ventilation opening
Ventilation grill
There are different options available for During construction the ventilation grill
constructing the top ventilation
opening:
can be built-in.
^ Cut an opening into the plinth b, as
shown in the illustration above.
^ Place the ventilation grill a into the
cut-out.
aDirectly above the appliance with a
vent grille (free airflow of at least
200 cm2)
^ Slide the clips c, from the back, into
the ventilation grill until the hooks
connect with the plinth.
bIn between the cabinet unit and the
ceiling
^ Install the plinth with the inserted
cThrough a suspended ceiling.
ventilation grill.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation information
Before installing the appliance
^ Before installation, remove the
accessories bag with the installation
components and other accessories
from the appliance, and remove the
sealing strip from the appliance door.
^ Do not remove any of the following
from the back of the appliance:
^ Open the appliance door and remove
the red transport clips a (depending
on model).
– The spacers (depending on model).
These ensure that the required
distance is maintained between the
back of the appliance and the wall.
– The pouches (depending on model)
located inside the metal grille (heat
exchanger)
These are important for the correct
functioning of the appliance. Their
contents are non-toxic and are not
dangerous.
^ Remove the cable clip from the back
of the appliance.
^ Check that all parts at the back of the
appliance can vibrate freely.
Carefully bend apart any parts that
are touching.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation dimensions
Before installation, make sure that the cabinet space matches the required
dimensions. The specified measurements for the ventilation openings must be
adhered to in order to ensure the proper functioning of the appliance.
Height of space [mm]
A
Freezer [mm]
B
KFNS 37432 iD
1772 – 1788
695
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the door hinges
The factory setting for the door hinges
allows them to open at a wide angle.
However, if the opening angle of the
door needs to be limited for any reason,
the hinge can be adjusted to
accommodate this.
– For example, the opening angle can
be limited to 90° if the appliance
door were to otherwise hit an
adjacent wall when opened.
^ Insert the limit pins provided into the
hinges from above.
The opening angle of the door is now
limited to 90°.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing the door hinging
^ Open both appliance doors.
When reversing the door hinging,
always enlist the help of another
person.
^ Remove the shelves / bottle shelf
from the appliance door.
The appliance comes with right-hand
door hinging. If left-hand hinging is
required, the door hinging must be
reversed:
To reverse the door hinging, you will
need the following tools:
^ Pull off the covers a, b, c and d.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing the door hinging
^ Slightly loosen the screws e and f
on the hinges.
^ Remove the screws e completely.
^ Place the mounting bracket i on the
opposite side and loosely screw in
the screws e.
^ Slide the doors g and h outwards
and take them off their hinges.
^ Remove screws e completely and
loosely screw them in on the opposite
side.
If you had inserted pins into the hinges
to limit the door's opening angle:
^ Pull the pins up and out of the
hinges.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing the door hinging
Carry out the following steps on both
doors.
Removing the soft-close mechanism
Caution! When removed from the
appliance, the soft-close
mechanism will snap shut. Risk of
injury!
^ Using a screwdriver, remove the ball
joint l and screw it into the adjacent
hole.
^ After detaching the door, lay it face
down on a stable surface.
^ Next, turn over the appliance door so
that it lies face up (hinges remain
open).
Do not close the hinges. Risk of
injury!
^ Remove the soft-close mechanism j
from the ball joint.
^ Unscrew the mount k and pull the
soft-close mechanism j towards you
to remove it.
^ Remove the screws e.
^ Place each hinge in the corner
diagonally opposite from its original
position n.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing the door hinging
Attaching the soft-close mechanism
^ Now turn over the appliance door so
that it lies face down.
^ Screw the mount k onto the hinge
and firmly tighten.
^ Pull the soft-close mechanism so that
it extends j and hook it onto the ball
joint.
^ Slide the appliance doors g and h
onto the premounted screws e and
f, and firmly tighten the screws e
and f.
^ Replace the covers a, b, c and d.
^ Insert the pins into the hinges from
above to limit the opening angle of
the doors.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
To install the appliance, you will
need the following tools:
Two people are required to install the
appliance.
^ The appliance must be installed in a
stable, solid cabinet unit that is
positioned on an even and level floor.
^ Secure the cabinet unit against
tipping.
^ Use a level to align the cabinet unit.
The cabinet corners must be at a 90°
angle to each other, otherwise the
cabinet door will not rest correctly on
all 4 corners of the cabinet.
^ The required size of the ventilation
openings must be ensured (see
"Installation information - Ventilation"
and "Installation dimensions").
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
You will need the following
installation components
– For mounting the cabinet door:
Each installation component is
designated by a number. The
component's number can also be found
in the installation steps on the following
pages.
– For installing the appliance in the
cabinet space:
All installations instructions shown
here are for a right-hand door
appliance. If you have reversed the
door hinging on your appliance, you
will need to adapt the instructions
accordingly.
Preparing the appliance
^ Position the appliance directly in front
of the housing unit niche.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
^ Slide the appliance two-thirds of the
way into the cabinet space.
Make sure that the power cable does
not get caught in the process.
Tip for sliding the appliance:
Tie a piece of string around the plug to
"extend" the length of the power cable.
Then pull the cable through the cabinet
unit by the opposite end of the string. It
will then be easier to plug in the
appliance once it has been installed.
For 5/8" (16 mm) cabinet walls only:
^ Slide the cover strip tabs a into
position.
^ Clip the spacers b and c onto the
right side of the hinges.
^ Open both appliance doors.
^ Screw the mounting bracket d onto
the pre-drilled holes in the appliance
door using the hex screw e.
Securely attach a second pair of
mounting brackets d in the handle
area of the door using the pre-drilled
holes in the appliance door.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
^ Now screw the adjustable feet l all
the way in.
^ Remove the cover f.
^ Loosely screw the mounting bracket
g onto the top left corner of the
appliance using the screws h. Do
not tighten the screws; the bracket
should still be able to slide from side
to side.
^ Attach the fitting piece i to the
mounting bracket j.
^ Carefully remove the protective film
from sealing strip m.
^ Loosely screw the mounting bracket
j to the base of the appliance using
the screws k. Do not tighten the
screws; the bracket should still be
able to slide from side to side.
^ Attach the sealing strip m flush with
the front of the appliance on the
door-opening side.
1. Position the sealing strip flush with
the lower edge of the top mounting
bracket.
2. Press down along entire length to
attach.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Installing the appliance
^ Check again to see whether the top
and bottom mounting brackets touch
the front edge of the cabinet side
wall.
^ Slide the appliance into the cabinet
space until the covers of the
mounting brackets touch the front
edge of the cabinet side wall.
This will help maintain a 1,6'' (42 mm)
distance from front edge of the
cabinet side walls along the entire
perimeter.
On cabinets with door fittings (e.g.
nubs, seals etc.) the dimension of
these parts must be taken into account
to ensure that there is a gap of 1,6'' (42
mm) on all sides of the appliance.
^ Pull the appliance forwards by the
appropriate distance.
The hinges and covers will now
protrude by a distance equal to the
depth of the door fitting.
Tip: Remove the door fittings. A flush
alignment with the surrounding cabinet
doors is still ensured.
^ p Align the appliance on both sides
until it stands straight by adjusting
the feet using the wrench provided.
– n For 5/8" (16 mm) walls:
The spacers should touch the front
edge at the top and bottom of the
cabinet side wall.
If a gap of 1,6'' (42 mm) is not
maintained between the perimeter of
the appliance housing and the front
edge of the cabinet side walls, the
door may not shut properly.
This can cause ice buildup,
condensation accumulation and
other malfunctions. These can all
lead to increased energy
– o For 3/4" (19 mm) walls:
The front edges of the top and
bottom hinges should be flush with
the front edge of the cabinet side
wall.
consumption.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Securing the appliance in the
cabinet space
^ Slide the loose bracket against the
cabinet wall.
^ Fasten the mounting bracket j to the
cabinet side wall using the screw s.
Drill a hole in the cabinet side wall if
necessary.
^ Push the hinged side of the
appliance against the cabinet wall.
^ Screw the particleboard screws s
through the hinge plates at the top,
bottom and then in the middle of the
appliance to secure it to the cabinet.
^ Fasten the mounting bracket g to the
cabinet side wall using the screws
t. Drill holes in the cabinet side wall
if necessary.
Important! Using your thumb, press
the protruding part of the bracket
against the cabinet wall while
tightening the screws. The appliance
must not pull back into the cabinet
space.
^ Retighten the screws h and k.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
For added stability of the appliance in
the cabinet unit, slide the included rods
between the cabinet floor and the
bottom of the appliance:
^ Snap the protruding ends off of the
mounting brackets. They are no
longer needed and can now be
disposed of.
^ Attach the covers f and u to the
corresponding mounting brackets.
^ First, attach the handle v to one of
the rods w.
^ Use the handle to slide the rod into
the guide as far as it will go.
Then, remove the handle and attach
it to the other rod provided. Push this
rod into its guide as far as it will go.
Important! Keep the handle in a safe
place in case you ever need to install
the appliance into another cabinet.
^ Close the appliance doors.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Mounting the cabinet doors.
Mounting doors that exceed the
maximum allowable weight can
damage the hinges. This may then
lead to functional problems with the
appliance.
The cabinet door must have a minimum
thickness of 5/8" (16 mm) and a
maximum thickness of 3/4" (19 mm).
The following gap sizes must be
maintained:
Before mounting furniture doors, make
sure that each door does not exceed
the maximum allowable weight:
– The gap between the cabinet door
and the unit door above must be at
least 0,1'' (3 mm).
Appliance
Max.
weight weight
of of lower
upper door in
Max.
– The vertical gap between cabinet
doors should also be about 0,1'' (3
mm). The exact size will vary
depending on the radius of the
cabinet door edges.
door in Ib (kg)
Ib (kg)
When installing the appliance in an
array of kitchen units, the top edge of
the cabinet door must be at the same
height as the cabinet doors of the
adjacent units.
KFNS 37432 iD
44 (20) 26 (12)
The cabinet door must be mounted so
that it is level and not under any stress.
When fitting large or divided furniture
doors an extra fitting kit or set of
fixing brackets should be used.
These are available to order from
Miele.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Carry out the following steps on both
doors.
Tip: Slide the fitting aids b and the
cabinet front up to the height of the
adjacent cabinet unit doors.
^ The factory setting for the distance
between the appliance door and the
mounting frame is 8 mm. Double
check this distance and adjust if
necessary.
^ Remove the nuts c and detach the
mounting frame d together with the
fitting aids b.
^ Slide the fitting aids b up to the
height of the cabinet door: The
bottom edge X of the fitting aids must
be at the same height as the top
edge of the cabinet door being
mounted (- symbol).
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
^ Lay the cabinet door face down on a
stable surface.
^ Slide the side cover q onto the
mounting frame on the side opposite
of the hinges.
^ Turn the furniture door over and
attach the handle (if necessary).
^ Using a pencil, lightly mark a line
down the centre of the inside of the
cabinet door e.
^ Hang the mounting frame d with the
fitting aids onto the inside of the
cabinet door. Align the mounting
frame centrally.
^ Fasten the mounting frame using at
least 6 short particleboard screws f.
(On cassette doors only use 4 screws
at the edges). Drill holes in the
cabinet door if necessary.
^ Pull the fitting aids upwards to
remove them g.
Turn them around and slide them into
the middle slots on the mounting
frame for safekeeping.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
^ Open the appliance door.
Adjusting the position of the door
^ Hang the cabinet door onto the
– Lateral adjustments (X)
^ Move the cabinet door.
– Vertical adjustments (Y)
alignment bolts h.
^ Loosely screw the nuts c onto the
adjustment bolts.
^ Turn the alignment bolts h using a
screwdriver.
^ Close the door and check the
distance between the door and the
adjacent cabinet doors. The gaps
should be even.
The distance between the appliance
door and the mounting frame is set to
8 mm. Adjust this distance within the
permitted range only.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
^ Drill the mounting holes l in the
cabinet door and fasten the screws
m. Make sure the two metal edges
are aligned flush with one another
(Symbol II).
^ Tighten the nuts c on each of the
appliance doors using a box-end
wrench j while holding the
alignment bolts c in place using a
screwdriver.
^ Close both doors.
^ The cover strip k must be
completely hidden in cabinet space.
It must not protrude.
Adjusting the position of the door
– Depths adjustments (Z)
^ Loosen the screws i at the top of
the appliance door and the screw n
on the mounting bracket the bottom.
Create a gap of 0,1'' (2 mm) between
the cabinet door and the cabinet
body by moving the cabinet door.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
^ Tighten all screws again.
The following confirm that the
appliance has been correctly
installed:
– The doors close properly.
– The doors do not touch the cabinet
body.
– The seals at the top corner of the
handle side fit tightly.
^ To check for proper installation, turn
on a flashlight, place it in the
appliance and close the doors.
Switch the lights off in the room. If
you see any light shining out on the
sides of the appliance, check the
installation steps again separately.
^ Replace each of the top covers o,
and click it into place.
^ Replace the side covers p, making
sure you hear them click into place.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
&DQDGD
,PSRUWHU
0LHOHꢀ/LPLWHG
+HDGTXDUWHUVꢀDQGꢀ0LHOHꢀ&HQWUH
ꢀꢁꢀꢂ&OURꢂ6ALLEYꢂ$RIVE
6AUGHANꢃꢂ/.ꢂꢂ,ꢄ+ꢂꢄ6ꢅ
WWWꢆMIELEꢆCA
&XVWRPHUꢀ&DUHꢀ&HQWUH
0HONEꢇꢂꢅꢈꢈꢉꢊꢁꢊꢉꢁꢄꢋꢊ
CUSTOMERCARE MIELEꢆCA
*HUPDQ\
0DQXIDFWXUHU
-IELEꢂꢌꢂ#IEꢆꢂ+'
#ARLꢉ-IELEꢉ3TRA”Eꢂꢍꢎ
ꢋꢋꢋꢋꢍꢂ'àTERSLOH
99
Download from Www.Somanuals.com. All Manuals Search And Download.
KFNS 37432 iD
en - CA
M.-Nr. 09 969 830 / 01
Download from Www.Somanuals.com. All Manuals Search And Download.
|