Miele Electric Pressure Cooker DA 3160 User Manual

Operating and installation instructions

Cooker hood

DA 3160

DA 3190

en - AU, NZ

To avoid the risk of accidents

or damage to this appliance

it is essential to read these

instructions before it is installed

and used for the first time.

M.-Nr. 06 794 960

Download from Www.Somanuals.com. All Manuals Search And Download.

Caring for the environment

Disposal of the packing

material

Disposal of your old appliance

Electrical and electronic appliances

often contain materials which, if

handled or disposed of incorrectly,

could be potentially hazardous to

human health and to the environment.

They are, however, essential for the

correct functioning of your appliance.

Please do not therefore dispose of it

with your household waste.

The transport and protective packing

has been selected from materials which

are environmentally friendly for

disposal, and can normally be

recycled.

Packaging e.g. cling film, polystyrene

and plastic wrappings must be kept out

of the reach of babies and young

children. Danger of suffocation!

Dispose of or recycle all packaging

materials safely as soon as possible.

Please dispose of it at your local

community waste collection / recycling

centre or contact your dealer for

advice. Ensure that it presents no

danger to children while being stored

for disposal.

It should be unplugged or disconnected

from the mains electricity supply by a

competent person.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety instructions

Safety with children

This appliance complies with all

relevant local and national safety

requirements. Inappropriate use

can, however, lead to personal injury

and damage to property.

This appliance is only intended for

use by adults who have read these

instructions.

This appliance is not a toy! To avoid

the risk of injury, keep children well

away and do not allow them to play with

it or to use the controls. They will not

understand the potential dangers

posed by it. They should be supervised

whenever you are working in the

kitchen.

To avoid the risk of accidents and

damage to the appliance, please

read these instructions carefully

before using it for the first time.

They contain important information

on the safety, installation, use and

maintenance of the appliance.

Older children may use the cooker

hood only when its operation has been

clearly explained to them and they are

able to use it safely, recognising the

dangers of misuse.

Keep these instructions in a safe

place and ensure that all users are

familiar with the contents. Pass them

on to any future owner of the

appliance.

Please be aware that on cooker

hoods with halogen lighting, the lamps

will get very hot during use and remain

hot for some time after switching off. To

safeguard against burning, keep

children well away from the lamps at all

times.

Correct application

This appliance is intended for

domestic use only.

Any other usage is at the owner's risk

and could be dangerous. The

manufacturer cannot be held liable for

damage resulting from incorrect or

improper use or operation.

Technical safety

Before installation, check the cooker

hood for visible signs of damage.

Under no circumstances should you

use a damaged appliance. A damaged

appliance is dangerous.

This appliance is not intended for

use by persons (including children)

with reduced physical, sensory or

mental capabilities, or lack of

experience or knowledge, unless they

are supervised whilst using it or have

been shown how to use it correctly by a

person responsible for their safety.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety instructions

Before connecting the appliance to

the mains supply, make sure that the

Installation, maintenance and

repairs may only be carried out by a

Miele authorised person in accordance

with current national and local safety

regulations.

voltage and frequency details given on

the data plate correspond with the

on-site electricity supply, otherwise the

appliance could be damaged. Consult

a qualified electrician if in any doubt.

Repairs and other work by unqualified

persons could be dangerous. The

manufacturer cannot be held liable for

unauthorised work.

The electrical safety of this

appliance can only be guaranteed

when continuity is complete between

Faulty components must only be

the appliance and an effective earthing replaced by genuine Miele original

system which complies with current

local and national safety regulations. It

is most important that this basic safety

requirement is present and tested

parts. The manufacturer can only

guarantee the safety of the appliance

when Miele replacement parts are

used.

regularly, and where there is any doubt,

the household wiring system should be

inspected by a qualified electrician.

The manufacturer cannot be held liable

for the consequences of an inadequate

earthing system (e.g. electric shock).

During installation, maintenance and

repair work, the appliance must be

disconnected from the mains electricity

supply. It is only completely isolated

from the electricity supply when:

– it is switched off at the isolator, or

For safety reasons, this appliance

may only be used when it has been

– the screw-out fuse is removed (in

countries where this is applicable), or

fully installed.

Only open the housing as described – the mains fuse is disconnected, or

in the instructions given in the

– it is switched off at the wall socket

and the plug withdrawn, or

installation sheet and in the Cleaning

and care section of this booklet. Under

no circumstances should any other

parts of the housing be opened.

Tampering with electrical connections

or components and mechanical parts is

highly dangerous to the user, and can

cause operational faults.

– the fuse from the fused spur

connection unit is withdrawn.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety instructions

Do not connect the appliance to the

Using at the same time as other

mains electricity supply by a

multi-socket unit or an extension lead.

These do not guarantee the required

safety of the appliance (e.g. danger of

overheating).

heating appliances that depend on

the air from the room

Warning - danger of toxic fumes

For appliances with an external fan

motor fitted (...EXT models) the

connection of the two units must be

made using the connection cable and

the plug connectors.

These models may only be combined

with a Miele external motor.

This appliance may only be used in

mobile installations such as ships,

caravans, aircraft etc. if a risk

assessment of the installation has been

carried out by a suitably qualified

engineer.

Great care should be taken when

using the cooker hood at the same time

and in the same room or area of the

house as another heating appliance

which depends on the air in the room.

Such appliances include gas, oil, wood

or coal-fired boilers and heaters,

continuous flow or other water heaters,

gas hobs, cookers or ovens which draw

air in from the room and duct exhaust

gases out through a chimney or

extraction ducting.

In areas which may be subject to

infestation by cockroaches or other

vermin, pay particular attention to

keeping the appliance and its

surroundings in a clean condition at all

times. Any damage which may be

caused by cockroaches or other vermin

will not be covered by the guarantee.

When used in extraction mode, with or

without an external motor fitted, the

appliance draws air in from the room in

which it is installed and from

neighbouring rooms.

If there is insufficient air, an

underpressure will occur. The heating

appliance may be starved of oxygen,

impairing combustion.

Harmful gases could be drawn out of

the chimney or extraction ducting back

into the room, with potentially fatal

consequences.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety instructions

In order to ensure safe operation, and

One of the following technical

measures may be necessary to ensure

safe operation.

to prevent gases given off by the

heating appliances from being drawn

back into the room when the cooker

hood and the heater are in operation

simultaneously, an underpressure of

0.04 mbar (4 pa) is the maximum

permissible in the room.

– If the only way of ensuring adequate

ventilation is via an open window, a

window contact switch should be

fitted to ensure that the cooker hood

can only operate when the window is

opened sufficiently. A window

contact switch kit is available from

good builders' merchants.

Take care when ventilating the room

through an open window that

ventilation is not impaired by a

closed blind or curtain.

– The cooker hood can be set up to

automatically switch on an air intake

fan or open a motorised inlet flap

when it is switched on.

– The cooker hood can be set up to

automatically switch off a heating

appliance which also depends on

the air from the room when it is

switched on.

Ventilation can be maintained by air

inlets which must not be blocked, in

windows, doors and outside wall vents,

or by other technical measures, such

as ensuring that the cooker hood can

only be switched on when the heating

appliance is switched off or vice versa.

A ventilation brick alone is not generally

sufficient to ensure safe ventilation.

The Miele DSM 400 control module

offers the possibility of combining other

components with the cooker hood (see

"Operation with Control module DSM

400").

,^{The overall ventilation condition}

of the dwelling must be taken into

account. If in any doubt, the advice

of a competent builder or, for gas, a

qualified gas fitter (Corgi registered

in the UK) must be sought.

It is available to purchase as an

optional extra.

If in any doubt , the advice of a

qualified builder, gas fitter (Corgi

registered in the UK) or electrician

must be sought.

If the hood is being operated in

recirculation mode, the above

restrictions do not apply.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety instructions

Correct use

Do not use the cooker hood without

the filters in place. This way you will

Never use an open flame beneath

avoid the risk of grease and dirt getting

into the appliance and hindering its

smooth operation.

the cooker hood. To avoid the danger

of fire, do not flambé or grill over an

open flame.

When switched on, the cooker hood

could draw flames into the filter. Fat

particles drawn into the cooker hood

present a fire hazard.

The filters should be regularly

cleaned or changed as appropriate.

Saturated filters are a fire hazard. See

"Cleaning and care".

When using the cooker hood over a

Do not use a steam-cleaner to clean

~ ~

gas hob, ensure that any burners in use this appliance. Pressurised steam

are always covered by a pan. Switch

the cooking zone off when a pan is

removed, even for a short time.

Regulate the flame so that it does not

burn up the sides of the pan.

Do not allow the pans to overheat

excessively (e.g. when using a wok).

The cooker hood can become

damaged when exposed to excessive

heat.

could reach the electrical components

and cause a short circuit.

Correct installation

Refer to the cooker or hob

manufacturer's instructions as to

whether a cooker hood may be

operated above the cooker/hob.

The minimum safety distances

between the top of the cooker or hob

and the bottom of the cooker hood

given in the "Appliance dimensions"

section of this booklet must be

maintained, unless the hob

Always switch the cooker hood on

when a cooking zone is in use,

otherwise condensation may collect in

the hood, which could cause corrosion.

When cooking with oil or fat, chip

manufacturer states that a greater

safety distance is required.

pans and deep fat fryers etc, do not

leave the pans unattended. Never leave

an open grill unattended when grilling.

Overheated oil and fat can ignite and

could set the cooker hood on fire.

If more than one cooking appliance is

fitted beneath the cooker hood, and

they have different minimum safety

distances to the cooker hood, select

the greater distance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety instructions

Follow the cooker or hob

The manufacturer cannot be held

liable for damage caused by

non-compliance with these Warning

and Safety instructions.

manufacturer's instructions on the use

of flammable materials over the

cooker/hob when installing a wood or

laminate lightshield onto the cooker

hood.

Safety regulations prohibit the fitting

of a cooker hood over solid fuel stoves.

All ducting, pipework and fittings

must be of non-flammable material.

These can be obtained from the Miele

Spare Parts department or from

builders' merchants.

The appliance must not be

connected to a chimney or vent flue

which is in use. Neither should it be

connected to ducting which ventilates

rooms with fireplaces.

If exhaust air is to be extracted into

a chimney or ventilation duct no longer

used for other purposes, seek

professional advice.

Accessories

Only use genuine Miele spare parts

and accessories with this appliance. If

spare parts or accessories from other

manufacturers are used, this will

invalidate the guarantee, and Miele

cannot accept liability.

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the appliance

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the appliance

a Exhaust socket ø 150 mm

b Control panel

c Grease filter

d Pull-out deflector plate

e Hob lighting

f Charcoal filter

(extra accessory available to order

for recirculation mode)

g Drop-down lightshield to conceal

control panel

The front of the deflector plate can

be fitted with a lightshield to match

your kitchen furniture.

The DA 3160 and DA 3190 can be

fitted with a DFB 61 or DFB 91

lightshield, available as an optional

accessory.

h On/Off touch control for the fan

i Controls to select fan power level

j Lighting touch control

Download from Www.Somanuals.com. All Manuals Search And Download.

Description of the functions

The cooker hood works with

. . . air extraction:

. . . air recirculation:

(air recirculation conversion kit

required)

The air is drawn in, cleaned by the

grease filter and then directed outside.

The air is drawn in and cleaned first by

the grease filter and then by a charcoal

filter. The cleaned air is then

If the on-site ventilation system does

not have a non-return flap, then the

non-return flap supplied with the

appliance must be fitted in the exhaust

socket in the motor unit.

recirculated back into the kitchen.

Charcoal filters are available to order

through your Dealer / Chartered Agent

or the Miele Spare Parts Department or

via the internet at www.miele-shop.com.

(See back cover for contact details and

"Technical Data" for model number).

Having a non-return flap fitted in the

ducting ensures that air, once ducted

to the outside, cannot get back into the

room again.

Before using the cooker hood in

recirculation mode, ensure that the

charcoal filter is in place; see

"Cleaning and care".

The flap is closed when the cooker

hood is switched off.

When the cooker hood is switched on,

the non-return flap opens for the

cooking vapours to be blown directly

outside.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

The cooker hood is operated by pulling When frying or cooking food with a

out and pushing in the deflector plate.

strong aroma, you may wish to select

the Intensive setting (yellow indicator

lamp) for a short period.

To switch the fan on

Pull the deflector plate right out to

achieve optimum extraction and to

^ Pull out the deflector plate.

The fan will begin to operate at setting II. prevent unnecessary noise levels.

To switch the fan off

^ Push the deflector plate back in. The

next time the deflector plate is pulled

The On/Off indicator lamp and the 2nd

out, the cooker hood will operate at

– / + power level indicator lamp will

power level II again.

light up.

If the cooker hood has been

^ Press the On/Off touch control for the

connected to a window contact

fan

switch via the Miele DSM 400 control

All the indicator lamps will go out.

module, then the fan cannot be

switched on if the window is shut.

To switch the lighting on

The indicator lamp will flash.

^ Pull out the deflector plate.

To select a power level

^ Use the – / + controls to select the

^ Press the touch control for the

power level required.

lighting again.

The indicator lamps show which power

When the lighting is switched on, the

level has been chosen.

indicator lamp lights up.

Depending on the intensity of the

cooking vapours, levels I to III (green

indicator lamps) are usually sufficient

for normal cooking.

To switch the lighting off

^ Push the deflector plate back in.

^ Press the touch control for the

lighting.

The indicator lamp will go out.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Automatic switch-off of the Intensive

setting

You can set the Intensive setting so that

it only runs for 10 minutes before

reverting automatically to level III.

^ Press the + touch control to activate

automatic switch-off.

^ To set this option, both the fan and

the hob lighting must be switched off

and the deflector plate pushed in.

The indicator lamps for fan power

levels I and IV will now light up

constantly.

Press the – touch control to

deactivate the automatic switch-off

function.

^ Press the – and + touch controls at

the same time for approx. 10

seconds until the first power level

indicator lamp lights up in the

display.

^ Press the On/Off touch control to

confirm.

^ Then press, one after the other,

Safety cut-out

Should the cooker hood be left on, the

fan will switch off automatically after 10

hours. The lighting will remain on.

– the hob lighting touch control,

^ Pressing the On/Off control will

switch the fan back on again.

– then the – touch control, and

– the hob lighting touch control again.

The indicator lamps for fan power levels

I and IV will flash if the automatic

switch-off of the Intensive setting is not

activated.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Before any cleaning or maintenance

work is carried out, disconnect the

cooker hood from the mains supply.

Ensure that:

Do not use too much water when

cleaning the controls. Water could

penetrate into the electronics and

cause damage.

– it is switched off at the wall socket

and the plug is withdrawn, or

– the fuse is withdrawn from the

fused spur connection unit, or

– the mains fuse is disconnected ,or

– the screw-out fuse is removed

(in countries where this is

Do not use:

– cleaning agents containing soda,

acids, chlorides or solvents,

– abrasive cleaning agents, e.g.

powder cleaners or cream cleaners

and abrasive sponges, as well as pot

scourers or sponges which have

been used previously with abrasive

cleaning agents. These will damage

the surface material.

applicable).

A range of Miele branded cleaning and

conditioning agents are available to

order through your Miele Dealer/

Chartered Agent, the Miele Spare Parts

Department or via the internet at

www.miele-shop.com.

Important for appliances with

stainless steel housing

(This infomation does not apply to the

controls).

Housing

Stainless steel surfaces can be cleaned

with a proprietary non-abrasive cleaning

agent designed specifically for use on

stainless steel.

General notes

Warning: The surfaces and controls

are susceptible to scratches and

abrasions. Please observe the

following cleaning instructions.

To help prevent re-soiling, a

conditioning agent for stainless steel

can also be used. Follow the

instructions on the label, and apply

sparingly with an even pressure in the

direction of the "grain".

^ All external surfaces and controls can

be cleaned using warm water with a

small amount of washing-up liquid

applied with a well wrung-out soft

sponge or cloth.

^ Wipe the surfaces dry using a soft

cloth.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Controls

Grease filter

The re-usable metal grease filter in the

appliance removes solid particles from

the kitchen vapours (grease, dust, etc)

preventing soiling of the cooker hood.

The controls may suffer

discolouration or damage if soiling is

left on them for too long. Remove

soiling straight away.

To avoid a build-up of fat, it should be

cleaned every 3-4 weeks on average,

but sooner if necessary.

Observe the General notes on cleaning

earlier in this section.

Do not use stainless steel cleaning

agents on the controls.

An oversaturated filter is a fire

hazard.

Important for DFB aluminium

lightshields

(optional accessory)

Aluminium is affected by the way that

light falls on it, by the surrounding

environment and by the angle you

observe it from.

Aluminium surfaces may suffer

discolouration or damage if soiling is

left on them for too long. Remove

any soiling straight away.

^ Grip the front of the deflector plate

together with the grease filter, and

pull outwards as shown.

^ Then pull the filter downwards to

Observe the General notes on cleaning

earlier in this section.

remove.

Do not use:

To avoid damaging the filter or the

hob below, make sure you hold the

filter securely at all times when

handling it.

– stainless steel cleaners,

– cleaning agents containing

descaling agents,

– dishwasher detergent,

– oven sprays.

^ Press the On/Off control to switch the

fan off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Cleaning the grease filters by hand

^ When removing the filter for cleaning,

also clean off any residues of oil or

fat from the now accessible housing

to prevent the risk of these catching

fire.

^ Clean the filters with a soft nylon

brush in a mild solution of hot water

and a small amount of washing-up

liquid.

Do not use undiluted washing up

liquid.

Do not use:

– cleaning agents containing

descaling agents,

– powder cleaners, cream cleaners or

abrasive all-purpose cleaning

agents,

– oven sprays.

Cleaning the grease filters in the

dishwasher

^ When putting it back, make sure that

the red plastic guides are at the

front and facing upwards.

^ Place the filters as upright as

possible in the lower basket, with the

short sides upright, and wash on a

65°C programme, ensuring the spray

arm is not obstructed. If a Miele

dishwasher is being used, select the

Sensor wash programme.

^ Replace the grease filter in the front

of the deflector plate, press it

upwards and push it in together with

the deflector plate. It will slide onto

the fixing pins at the back. Finally,

push the grease filter back a little

more.

^ Use a mild dishwasher detergent.

Depending on the cleaning agent

used, cleaning the grease filter in a

dishwasher can cause permanent

discolouration to the surface.

However, this will not affect the

functioning of the filter in any way.

^ After cleaning, leave the filter to dry

for a while on an absorbent surface

before putting it back in place.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Fitting and replacing the

charcoal filter

If the cooker hood is connected for

recirculation, a charcoal filter (optional

accessory) must be inserted in addition

to the grease filter.

This is designed to absorb cooking

smells.

It is fitted in the canopy above the

grease filter.

Replacement charcoal filters can be

obtained from your Dealer /

Chartered Agent or the Miele Spare

Parts department or via the internet

on www.miele-shop.com. See back

cover for contact details, and

"Technical data" for type and

reference number.

Follow the instructions supplied with the

charcoal filter when fitting it.

Replace the charcoal filter at least

every six months or more frequently if

necessary.

Used charcoal filters can be disposed

of with the normal domestic waste.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Changing a halogen lamp

^ Pull out the deflector plate, and

remove the grease filter as described

earlier.

^ Switch off the fan and the lighting.

Exercise caution when changing

halogen lamps. They get very hot

during use, and remain hot for some

time after being switched off. Do not

touch the surface directly when

changing a lamp, as grease

particles from your fingers will

adhere to the surface and damage

it. Please follow the manufacturer’s

instructions.

^ Push down the lighting unit slightly

^ Remove the charcoal filter if the

cooker hood is being used in

recirculation mode.

via the opening in the safety panel.

^ The halogen lamp is now accessible

to be unscrewed anti-clockwise.

Before any cleaning or maintenance

work, disconnect the cooker hood

from the mains supply. Ensure that

^ Replace it with a new halogen lamp

(specification: GU/GZ 10, 230 V,

50 W). Screw the lamp into the

socket and push it upwards.

–

it is switched off at the wall socket

and the plug is withdrawn, or

the fuse is withdrawn from the

fused spur connection unit, or

the mains fuse is withdrawn,or

the screw-out fuse is removed

(in countries where this is

applicable).

–

We recommend only using lamps of the

same specification and also made by

the same manufacturer as the ones

being replaced.

–

^ Replace the grease filter and, if being

used in recirculation mode, the

charcoal filter.

Download from Www.Somanuals.com. All Manuals Search And Download.

Appliance dimensions

DA 3190*

DA 3160

1) In extraction mode: when measuring

for the height of the wall housing unit

and the cut-out, account must be taken

of any accessories fitted, e.g. a

condensate barrier.

2) Recirculation mode requires

installation kit DUU 151.

3) Accessory DSM 400.

* Installation is also possible in a

600 mm wide unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Appliance dimensions

Safety distance between hob and

cooker hood

The minimum safety distances

between the top of a cooker or hob

and the bottom of the cooker hood

are as follows, unless a greater

distance is specified by the

manufacturer of your cooking

appliance:

- 600 mm above electric hobs and

cookers,

- 650 mm above an open grill or

deep fat fryer,

- 650 mm above gas hobs and

cookers.

If this cooker hood is installed above

a Miele Wok CS 1028 CombiSet

appliance, a minimum safety

distance of 760 mm must be

maintained between the burner and

the lower edge of the cooker hood.

See “Warning and Safety

instructions” for further information.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Installation accessories

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

a 2 hose clips

for securing the vent ducting to the

exhaust socket.

8 screws 3.5 x 16 mm

b 1 non-return flap

for securing the cooker hood into the

wall unit.

for fitting into the exhaust socket on

the motor unit (only for air extraction

mode).

Depending on model, the non-return

flap may already be fitted.

8 screws M4 x 12 mm

for securing the cooker hood to the

brackets.

c 2 brackets

to support the appliance in the wall

unit.

4 of the screws can be used instead of

the plastic rivets to secure the spacer

strip.

d 1 spacer strip

to conceal the gap between the rear

of the appliance and the wall.

e Conversion kit for recirculation

mode

including exhaust grille and flexible

aluminium hose (the conversion kit is

not supplied with the cooker hood but

is available as an optional accessory;

see "Technical data").

2 screws 4 x 30 mm

for securing the cooker hood at rear wall.

4 plastic rivets

f DML 300 installation kit (optional

accessory)

for securing the spacer strip to the

back of the appliance.

contains hinging and screws for

fixing a lightshield to match kitchen

furniture (lightshield not supplied with

cooker hood)

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Positioning the appliance in

the wall housing unit

To position the appliance correctly,

cut the spacer strip to required depth

T, and then attach it to the back of

the appliance.

T= Depth of carcase K minus depth of

appliance G

^ Screw the spacer strip to the bottom

of the sides of the housing, flush with

the rear wall.

^ The depth of appliance G depends

on the lightshield being used:

– a Lightshield to match existing

kitchen furniture

– b DFB lightshield (optional

accesssory)

– c No lightshield.

This is based on a lightshield which

aligns with the front edge of the

carcase.

^ Draw a vertical line up both inside

walls of the housing from the front of

the spacer strip.

If the lightshield is further forward or

back, measurement T will need to be

adjusted accordingly.

^ Cut the spacer strip supplied to

measurement T .

Score along the groove for the

smaller measurement as shown, and

remove the surplus.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

^ Place the appliance on its back.

Do not remove the protective film

between the deflector plate and the

casing until the hood has been

placed in the housing unit.

^ Screw the brackets onto the right and

left inside walls of the housing unit as

shown. The back edge of the

brackets should align with the vertical

line drawn up from the front of the

spacer strip, and the lower edge

aligned with the lower edge of the

housing unit side wall.

The brackets are designed for 16

and 19 mm thick carcase sides.

Orientate the bracket so that the

vertical depth matches the thickness

of the panel, as shown.

^ Hold the grease filter firmly, and pull

it out with the deflector plate as

shown.

^ Remove the grease filter and place to

one side.

^ Push the deflector plate back in.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Note for dismantling the cooker hood:

Undoing the screws on the left and

right inside the housing releases the

brackets, allowing the appliance to

be removed from the unit.

^ When fitting a DA 3190 into a 60 cm

housing unit, unscrew the brackets

on the deflector plate whilst it is

pulled out.

^ Push the cooker hood back against

the spacer strip.

^ Pull out the deflector plate.

^ Secure the appliance to the brackets

using 2 screws on each side.

^ Remove the protective film between

the deflector plate and the casing.

^ Lift the appliance up into the housing

from below, and engage in the

brackets.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

^ Secure the spacer strip to the back of

the appliance from behind using

4 plastic rivets as shown.

^ Loosen the screws of the fixing

brackets on the top of the appliance.

^ Push the brackets flush to the wall

or the cabinet back wall.

^ Drill respective holes and screw

the fixing brackets to the wall or the

cabinet rear wall. Tighten the screws

to the casing.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Attaching the lightshield

Aligning the deflector plate

^ Attach the lightshield (if using).

A DML 300 installation kit, available as

an optional accessory, is required for

this.

This installation kit is supplied with a

DFB lightshield.

^ The position of the deflector plate

can be brought forward by up to

50 mm using the adjusting screws on

either side of the deflector plate.

Align the deflector plate to the front of

the kitchen furniture units on either

side.

Follow the installation instructions

supplied.

Weight of a lightshield matching

existing furniture

The lightshield must not exceed 1300 g

in weight.

This applies to lightshields with a depth

of up to 30 mm.

For larger or heavier lightshields, the

weight must be reduced by e.g.

trimming it down at the back.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Replacing the grease filter

Set up for extraction mode

^ Remove the protective strip around

the edge of the grease filter.

^ If the on-site ventilation system does

not have a non-return flap, then the

non-return flap supplied with the

appliance must be fitted in the

exhaust socket in the motor unit.

Depending on model, the non-return

flap may already be fitted.

Replace the grease filter.

^ To do this, pull the deflector plate out.

^ Secure the ventilation ducting over

the exhaust socket on the cooker

hood using a hose clip.

^ See "Connection for air extraction" for

further instructions on fitting the

ducting.

^ Turn the grease filter so that the red

plastic guides are at the front and

facing upwards.

^ Replace the grease filter in the front

of the deflector plate, press it

upwards and push it in together with

the deflector plate. It will slide onto

the fixing pins at the back. Finally,

push the grease filter back a little

more.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Set up for recirculation mode

143

319

If site conditions are not suitable for the

cooker hood to be used with air

extraction, the appliance must be set

up for recirculation.

For this, a conversion kit DUU 151,

available from your Miele dealer or the

Miele Spare Parts Dept., is required.

240

110

223

160

150

^ The non-return flap is not needed for

the recirculation mode. Depending

on model, it may already be fitted.

Pull the non-return flap off the bracket

from vent connection.

You will also need a charcoal filter (see

“Technical data”).

^ Fit the conversion kit as described in

the installation instructions supplied

with the kit.

^ Make sure that the slats on the

exhaust grille are directed towards

the middle of the room, and not

towards the wall or the ceiling.

^ Fit the charcoal filter (see “Cleaning

and care”).

Electrical connection

Refer to the notes in “Electrical

connection” and “Warning and

Safety instructions” before

connecting to the electricity supply.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection for air extraction

,^{Important: To avoid the danger}

of toxic fumes, please observe the

Warning and Safety instructions.

This is especially crucial when using

the cooker hood at the same time as

another heating appliance which

relies on air from the same room.

The cooker hood should be installed

according to local and national

building regulations. Seek approval

from the building inspector where

necessary.

If the exhaust ducting is secured to

the exhaust stub by a hose clip,

ensure that it is fitted correctly. Do

not overtighten.

Otherwise the exhaust stub could

buckle and the non-return flap could

become jammed.

– All ducting, pipework and fittings

must be of non-flammable materials.

– The exhaust ducting should be as

short and straight as possible.

– To ensure efficient air extraction, the

diameter of the exhaust ducting

should not be less than 150 mm.

If exhaust ducting with a diameter of

less than 150 mm, or if flat ducting is

used, the noise level of the cooker

hood will increase and extraction will

be less efficient.

– Where ducting is horizontal, it must

be laid to slope away at at least 1 cm

per metre.

This is to ensure that condensate

cannot drain back into the cooker

hood.

Only reduce the diameter of the

ducting if absolutely necessary, e.g.

where narrower ducting has already

been installed.

– If the exhaust air is to be ducted into

the open air, the installation of a

telescopic wall vent is recommended.

– Only use wide radius bends. Tight

bends reduce the air throughput of

the cooker hood.

– If the exhaust air is to be ducted into

a vent flue, the ducting must be

directed in the flow direction of the

flue.

– Only use smooth pipes or flexible

hoses made from non-flammable

materials for extraction connection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection for air extraction

Important:

If the exhaust ducting is to run through

rooms, ceiling space etc. where there

may be great variations in temperature

between the different areas, the

problem of condensation will need to

be addressed. The exhaust ducting will

need to be suitably insulated.

Condensate trap

(optional extra)

In addition to insulating the exhaust

ducting, we recommend that a suitable

condensate trap is also installed to

collect and evaporate any condensate

which may occur. Condensate traps

are available for C 125 mm or

C 150 mm ducting.

When installing a condensate trap,

ensure that it is positioned vertically

and if possible directly above the

exhaust connection. The arrow on the

housing indicates the direction of

air-flow.

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical connection

If the switch is not accessible after

installation (depending on country), an

additional means of disconnection must

be provided for all poles.

All electrical work should be

undertaken by a suitably qualified

and competent person in strict

accordance with current national

and local safety regulations

(BS 7671 in the UK).

For extra safety it is advisable to protect

the appliance with a suitable residual

current device (RCD). Contact a

qualified electrician for advice.

Installation, repairs and other work

by unqualified persons could be

dangerous, for which the

Important

This appliance is supplied for

connection to an a.c. 230 V single

phase 50 Hz supply.

manufacturer cannot be held liable.

Ensure power is not supplied to the

appliance until after installation or

repair work has been carried out.

The wires in the mains lead are

coloured in accordance with the

following code:

Do not connect the appliance to the

mains electricity supply by an

extension lead. These do not

guarantee the required safety of the

appliance.

Green/yellow = earth

Blue

= neutral

= live

Brown

WARNING:

THIS APPLIANCE MUST BE

EARTHED

The connection data is given on the

data plate. This is visible when the

grease filters have been removed.

Ensure that this data matches the

household mains supply.

Connection of this appliance should be

made via a suitable isolator or a double

pole fused spur connection unit which

complies with national and local safety

regulations and the On-Off switch

should be easily accessible after the

appliance has been built in.

When switched off there must be an

all-pole contact gap of 3 mm in the

switch (including switch, fuses and

relays according to EN 60335).

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation with DSM 400 control module

The Miele DSM 400 control module can

If the control module is

be used to combine the cooker hood

with other components.

disconnected in order to operate the

cooker hood without the window

contact switch (e.g. after moving

house), the cooker hood electronics

must be reset by a Miele service

technician.

It enables the following:

Connection to a window contact

switch

If adequate ventilation to the room can

only be ensured by having a window

open when the cooker hood is in use at

the same time as a heating appliance

which depends on the air from the

same room, then the control module

can be used to connect a window

contact switch (not supplied) to the

appliance.

Potential free connection

This enables a further appliance to be

controlled by the switch setting on the

cooker hood fan.

– For instance it can be used to ensure

a sufficient supply of fresh air when

the cooker hood and a heating

appliance which also depends on

the air in the room are being used

together, by switching on an air

intake fan, or opening a motorised

inlet flap as soon as the cooker hood

fan is switched on.

Once connnected, the cooker hood can

only be operated when the window is

sufficiently open (see also "Warning

and Safety instructions").

When the window is closed, the cooker

hood fan cannot be switched on. The

indicator lamp for the On/Off touch

control on the cooker hood will flash.

It is important to ensure that the fan

power is sufficient and that the air

intake has a suitable cross-sectional

diameter.

The cooker hood lighting is not affected

by this.

– If a sufficient air intake cannot be

guaranteed, then the potential free

contact will enable a heating

EXT models can also be connected to a

window contact switch.

appliance, which depends on air in

the same room as a cooker hood, to

be switched off when the cooker

hood is in operation.

Take care when ventilating the room

through an open window that ventilation

is not impaired by a closed blind or

curtain.