Miele Dishwasher G 856 SC ELITE User Manual

Operating instructions  
Novotronic  
G 856 SC Elite  
UV  
To prevent accidents  
and machine damage,  
read these instructions  
before  
installation or use.  
M.-Nr. 05 431 320  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Operation  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY INSTRUCTIONS  
WARNING –  
When using your dishwasher, follow  
basic precautions, including the fol-  
lowing:  
Do not use an extension cord to  
connect this appliance to electric-  
ity. Extension cords do not guarantee  
the required safety of the appliance  
(e.g. danger of overheating).  
Be certain your appliance is prop-  
erly installed and grounded by a  
Read all instructions before installa-  
tion or use of the dishwasher to pre-  
vent injury and machine damage.  
qualified technician. To guarantee the  
electrical safety of this appliance, conti-  
nuity must exist between the appliance  
and an effective grounding system. It is  
imperative that this basic safety require-  
ment be met. If there is any doubt, have  
the electrical system of the house  
checked by a qualified electrician. The  
manufacturer cannot be held responsi-  
ble for damages caused by the lack, or  
inadequacy of, an effective grounding  
system.  
The manufacturer cannot be held re-  
sponsible for damage or injury  
caused by improper use of this ap-  
pliance.  
Use the dishwasher only for its in-  
tended purpose. This appliance is  
intended for residential use only.  
Installation  
Keep these operating instructions in  
a safe place and pass them on to  
any future user.  
Installation and repair work should  
be by a Miele authorized service  
technician. Work by unqualified per-  
sons could be dangerous and could  
void the warranty.  
Electrical safety  
This equipment is not designed for  
maritime use or for use in mobile  
installations such as caravans or air-  
craft. However, under certain conditions  
it may be possible for an installation in  
these applications. Please contact the  
nearest Miele dealer or the Miele Tech-  
nical Service Department with specific  
requirements.  
Before installation make sure that  
the voltage and frequency listed on  
the data plate correspond with the  
household electrical supply. This data  
must correspond to prevent injury and  
machine damage. Consult a qualified  
electrician if in doubt.  
Before installation or service, dis-  
connect the power supply to the  
work area by unplugging the unit, “trip-  
ping” the circuit breaker or removing  
the fuse.  
Inspect the dishwasher for ship-  
ping damage. Do not install or op-  
erate a damaged unit. Contact the  
place of purchase.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
IMPORTANT SAFETY INSTRUCTIONS  
Ensure that any plastic wrappings,  
bags etc. are disposed of safely  
Do not wash plastic items unless  
they are labeled "dishwasher safe"  
and kept out of the reach of babies and or the equivalent. For items not labeled,  
young children. Danger of suffocation!  
check the manufacturer’s recommenda-  
tions.  
This dishwasher should only be in-  
stalled under a continuous  
countertop secured to adjacent  
cabinetry.  
When loading tableware, place  
sharp items away from the door  
seal to prevent damage to the seal.  
Load knives pointing downwards to  
prevent injuries.  
Do not install this dishwasher be-  
neath a cooking surface or oven.  
Only use detergents and rinse aids  
recommended for residential dish-  
washers. Keep all detergents and rinse  
aids out of the reach of children.  
Do not, under any circumstances  
cut the intake hose or submerge in  
liquid. This hose contains electrical  
components that could cause injury or  
property damage if cut or submerged.  
Do not drink water from the dish-  
washer! Harmful residues could be  
present.  
Use  
Only use the dishwasher if all pan-  
els are properly in place.  
For dishwashers with visible heating  
element  
Do not touch the heating element  
during or immediately after use.  
Do not tamper with the controls.  
To reduce the risk of injury, do not  
allow children to play in, on, or  
near the dishwasher.  
Disposal of an appliance  
If the appliance is removed from its  
installation and will not be used,  
the door to the wash cabinet should be  
removed to prevent children from being  
locked in the machine. When discard-  
ing an old dishwasher, unplug it from  
the power outlet, remove the door to the  
wash cabinet and cut off the power  
cord.  
Do not abuse, sit, or stand on the  
door or baskets of the dishwasher.  
Under certain conditions, hydrogen  
gas may be produced in a hot  
water system that has not been used  
for two weeks or more. HYDROGEN  
GAS IS EXPLOSIVE. If the hot water  
system has not been used for such a  
period, turn on all hot water faucets and  
let water flow from each for several min-  
utes before using the dishwasher. This  
will release any accumulated hydrogen  
gas. Do not smoke or use an open  
flame during this time.  
SAVE THESE  
INSTRUCTIONS  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
MESURES DE SÉCURITÉ IMPORTANTES  
AVERTISSEMENT –  
Les réparations doivent être effec-  
tuées uniquement par une per-  
Au moment d’utiliser votre  
lave-vaisselle, veuillez observer  
toutes les mesures de sécurité de  
base.  
sonne compétente. Débrancher l’appa-  
reil de la prise de courant avant d’en  
faire l’entretien (enlever la fiche de la  
prise ou fermer le disjoncteur).  
Installer uniquement ce lave-vais-  
selle sous un comptoir continu qui  
est fixé à des meubles adjacents.  
Cet appareil électroménager est con-  
forme à tous les règlements et codes  
sur la sécurité. Pour éviter de vous  
blesser et d’endommager l’appareil,  
veuillez lire soigneusement les in-  
structions sur l’utilisation.  
Vous devez mettre le lave-vaisselle  
à la terre. Installer le lave-vaisselle  
en observant les instructions pour l’ins-  
tallation ci-jointes.  
Utiliser des détersifs pour les  
lave-vaiselle ménagers seulement.  
Utiliser uniquement des détersifs et des  
produits de rinçage recommandés pour  
les lave-vaisselle.  
N’utilisez le lave vaiselle que pour  
laver la vaiselle.  
Le fabricant ne peut être tenu  
responsable des dommages ou  
blessures causés par une utilisation  
inadéquate ou par des utilisations  
autres que celles auxquelles  
l’appareil est destiné.  
Ne pas utiliser votre lave-vaisselle  
à moins que tous les panneaux  
soient bien en place.  
Ne pas permettre aux enfants de  
jouer dans ou sur le lave-vaisselle.  
Ranger tous les détersifs et pro-  
duits de rinçage hors de la portée  
des enfants.  
Ne pas modifier  
les commandes.  
Ne pas boire l’eau du meuble de  
lavage.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
MESURES DE SÉCURITÉ IMPORTANTES  
Au moment de remplir le lave-vais-  
selle :  
Ne pas abuser et ne pas vous as-  
seoir ni vous tenir sur la porte ou  
sur les paniers du lave-vaisselle.  
– Mettre les articles pointus de  
manière à ce qu’ils n’endommagent  
pas le seau étanche de la porte.  
Enlever la porte et couper le cor-  
don du lave-vaisselle avant de l’en-  
lever aux déchets afin d’empêcher les  
enfants de se blesser ou de s’enfermer  
dans l’appareil par accident.  
– Mettre le tranchant des couteaux  
vers le bas afin de réduir les risques  
de blessure.  
Ne pas laver les articles en plas-  
tique à moins qu’ils n’indiquent "Va  
au lave-vaisselle" ou l’équivalent. Véri-  
fier les recommandations du fabricant  
poir les articles non étiquetés.  
Lave-vaiselle avec l’élément  
chauffant  
Ne touchez pas l’élément chauffant  
pendant le fonctionnement de l’ap-  
pareil ou immédiatement après.  
Dans certaines conditions, un sys-  
tème d’eau chaude qui n’a pas été  
utilisé pendant plus de deux semaines,  
peut dégager de l’azote.  
L’AZOTE EST EXPLOSIF. Si le système  
d’eau chaude n’a pas été utilisé pen-  
dant une telle période de temps, ouvrir  
tous les robinets d’eau chaude et lais-  
ser l’eau couler pendant plusieurs mi-  
nutes avant d’utiliser le lave-vaisselle.  
Ceci dissipera tout l’azote accumulé.  
Ne pas fumer ni utiliser une flamme nue  
durant ce temps.  
CONSERVER CES  
INSTRUCTIONS  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caring for the environment  
Energy saving washing  
This dishwasher is exceptionally eco-  
nomical in the use of water and electric-  
ity. For best results follow these tips:  
^ For lowest energy consumption and  
the gentlest washing of china and  
crystal, connect the dishwasher to a  
cold water source.  
^ For fastest possible wash times, yet  
higher energy consumption, connect  
the dishwasher to a hot water source.  
^ Make full use of the baskets without  
overloading for the most economical  
washing.  
^ Choose a program that best suits the  
degree of soiling and the type of  
dishes being washed.  
^ For small loads:  
Select the "Top Solo" feature (see  
"Additional features").  
^ If baskets are only half full, select the  
"Economy" program.  
^ Use the correct amounts of detergent  
and rinse aid.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Guide to the dishwasher  
Wash cabinet  
1
2
3
4
5
6
Upper spray arm (not visible)  
Cutlery tray  
7
8
9
Four height adjustable feet  
Triple Filter System  
Salt reservoir  
Upper basket  
Water feed for middle spray arm  
Middle spray arm  
10 Detergent dispenser  
11 Rinse aid reservoir  
12 Data plate  
Lower spray arm  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Guide to the dishwasher  
Control panel  
13 "On/Off" button  
19 "Start" button  
14 Program sequence display  
15 "Top Solo" button  
16 Delay Start display  
17 Program selector  
18 "Delay Start" button  
20 Check/Refill indicators  
21 Child Safety Lock  
22 Door release  
23 Drying vent  
Every dishwasher is tested before leaving the factory. Any water remaining in  
the machine is from these tests and does not indicate that the machine has  
been used.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
To open the door  
Child Safety Lock  
The yellow key for the Child Safety  
Lock is shipped on one of the spikes  
at the front of the upper basket. Re-  
move the key before using the dish-  
washer.  
The Child Safety Lock is designed to  
prevent children from opening the dish-  
washer.  
^ Press the release catch inside the  
door grip.  
If the door is opened during operation,  
the dishwasher will stop running. Once  
the door is closed the program will re-  
start.  
To close the door  
^ Push the baskets in.  
^ Use the provided key to lock or un-  
lock the dishwasher.  
^ Lift the door and push until it clicks  
into position.  
Horizontal:  
the door is locked  
Vertical:  
the door can be opened  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
Water softener  
If your water hardness is consistently  
lower than 8 gr/gal (140 ppm), you do  
not need to add dishwasher salt. How-  
ever, the dishwasher must still be pro-  
grammed to correspond to the local  
water hardness.  
To achieve good cleaning results, the  
dishwasher needs soft water. Hard  
water results in calcium deposits on  
dishware and in the dishwasher.  
If your tap water hardness is above  
8 gr/gal (values are in US gallons)  
(140 ppm), the water should be soft-  
ened. This takes place automatically in  
the unit’s integrated water softener.  
Where the water hardness fluctuates  
e.g. between 9 - 17 gr/gal (160 - 310  
ppm), always program the machine to  
the higher value, 17 gr/gal (310 ppm) in  
this example.  
– Your local water authority will be able  
to advise you of the water hardness  
level in your area.  
If there is a fault, it will help the service  
technician to know the hardness of your  
local water supply.  
– The dishwasher must be pro-  
grammed to correspond to the water ^ Please note the water hardness:  
hardness in your area.  
gr/gal  
– The water softener must be filled with  
dishwasher salt for reactivation.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
Programming the water softener  
Your water hardness level must be pro-  
grammed into the dishwasher using the  
program selector and buttons on the  
control panel.  
^ Make sure the dishwasher is turned  
off.  
^ Turn the program selector to "Stop".  
^ Press and hold the "Top Solo" button  
and at the same time turn on the  
dishwasher with the "On/Off" button.  
Release the "Top Solo" button within  
two seconds.  
^ Turn the program selector to the posi-  
tion which corresponds to the water  
hardness in your area (see table).  
The "Salt" indicator will flash.  
If the "Rinse aid" indicator comes on,  
the rinse aid dispenser needs to be  
filled.  
gr/gal*  
1 - 4**  
ppm  
Selector setting  
Normal Plus  
20 - 70  
90 - 130  
140 - 180  
200 - 230  
250 - 290  
310 - 400  
410 - 630  
650 - 1260  
5 -  
7
Normal  
If any other indicator is lit or flashing,  
the above steps must be repeated.  
8 - 10  
11 - 13  
14 - 16  
17 - 22  
23 - 35  
36 - 70  
China & Crystal  
Rinse & Hold  
5 o’clock position  
6 o’clock position  
7 o’clock position  
Energy Saver  
* US gallons  
** factory preset  
Example:  
Water hardness is 20 gr/gal.  
Turn the program selector to the  
"6 o’clock" position.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
^ Press the "Top Solo" button.  
The "Top Solo" indicator will light.  
^ Turn the program selector to "Stop".  
^ Turn off the dishwasher.  
Checking the programmed water  
hardness  
^ Make sure the dishwasher is turned  
off.  
^ Turn the program selector to "Stop".  
The programmed water hardness is  
stored.  
^ Press and hold the "Top Solo" button  
and at the same time turn on the  
dishwasher with the "On/Off" button.  
Release the "Top Solo" button within  
two seconds.  
The "Salt" indicator will flash.  
If the "Rinse aid" indicator comes on,  
the rinse aid dispenser needs to be  
filled.  
If any other indicator is lit or flashing,  
the above steps must be repeated.  
^ Turn the program selector clockwise  
until the "Top Solo" indicator comes  
on.  
The position where the "Top Solo" indi-  
cator comes on corresponds to the pro-  
grammed water hardness (see table in  
"Programming the water softener").  
^ Turn the program selector to "Stop".  
^ Turn off the dishwasher.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
Filling the salt reservoir  
To fill the salt reservoir:  
If your water hardness level is greater  
than 8 gr/gal, the salt reservoir should  
be filled before the first use and when  
the "Salt" indicator lights.  
^ Remove the lower basket.  
^ Unscrew and remove the salt reser-  
voir cap located on the floor of the  
wash cabinet.  
Only use water softener salt specially  
formulated for dishwashers. Other salts  
may contain insoluble additives which  
can impair the water softener.  
^ Place the provided funnel over the  
salt reservoir.  
The salt reservoir must be filled with  
2 quarts (2 l) of water before adding  
salt for the first time. Water does not  
have to be added with subsequent  
refills.  
The proper salt can be purchased from  
your Miele dealer or Miele’s Technical  
Service Department.  
,Inadvertently filling the salt  
reservoir with dishwashing deter-  
gent will damage the water soft-  
ener.  
^ Carefully fill with salt. The salt reser-  
voir holds approximately 4.5 lbs  
(2 kg) of salt. As it is filled, water will  
run out.  
^ Clean any excess salt from the  
threads of the reservoir opening.  
^ Screw the cap on firmly.  
^ If the dishwasher will not be used im-  
mediately, run the "Rinse & Hold" pro-  
gram. This will remove any traces of  
salt from inside the wash cabinet.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using for the first time  
Salt indicator  
Bypassing the salt indicator  
When the salt reservoir is empty, the  
"Salt-PC" indicator will light, indicating  
that it should be refilled with reactiva-  
tion salt.  
If your water is soft (below 8 gr/gal) the  
salt reservoir should not be filled with  
salt. The indicator will remain lit and  
should be disregarded or bypassed.  
^ Remove the salt reservoir cap.  
Looking into the salt reservoir, you will  
see the top of the float chamber on the  
right hand side, a.  
After the reservoir has been filled, the  
water softener is automatically reacti-  
vated the next time the dishwasher is  
started. The "Salt" indicator will be lit  
during this process.  
^ Using a screwdriver, carefully pivot  
the float chamber towards the center  
of the reservoir.  
^ Using needle nose pliers, pull the  
cap, b, off of the float chamber, and  
remove the float, c.  
Replace the float chamber cap, push  
the chamber back into its upright posi-  
tion, and replace the salt reservoir cap.  
The "Salt" indicator should no longer be  
lit.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
Rinse aid  
Rinse aid is recommended to prevent  
spotting on dishes and glassware.  
,Filling the rinse aid reservoir with  
detergent will damage the reservoir.  
Only pour rinse aid formulated for  
residential dishwashers into the  
reservoir.  
Adding rinse aid  
^ Pour liquid rinse aid into the reservoir  
until it is visible on the surface of the  
screen.  
^ Press on the flap until you hear it  
click shut. Failure to close it all the  
way will allow water to enter the res-  
ervoir during the wash program.  
^ Wipe up any spilled rinse aid. The  
flap will remain closed during normal  
operation.  
^ Add rinse aid before the first use and  
whenever the "Rise aid" indicator  
lights.  
^ Press the button in the direction of  
the arrow until the flap springs open.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
Adjusting the dosage  
Rinse aid indicator  
The rinse aid indicator on the control  
panel will light when the rinse aid reser-  
voir needs refilling.  
The dosage selector is preset to 3. This  
dispenses approximately 3 ml of rinse  
aid per program. It can be adjusted  
from 1 to 6.  
When the indicator first comes on, there  
will be enough rinse aid left for 2 - 3  
washes.  
^ Use a higher setting if spots appear  
on dry glassware.  
^ Use a lower setting if streaking ap-  
pears on dishes or glasses.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
^ The spray arms must not be blocked  
by items that are too tall or hang  
through the baskets. Check clear-  
ance by manually rotating the spray  
arms.  
,Do not wash items soiled with  
ash, sand, wax, grease or paint in  
the dishwasher.  
Ash and sand do not dissolve and  
will be distributed through out the in-  
side of the dishwasher.  
Wax, grease and paint will cause  
permanent discoloration or damage  
to the dishwasher.  
^ Food residue and spilt liquids should  
be cleaned from the sides of the  
dishwasher door. These are outside  
of the wash cabinet and are not  
cleaned by water from the spray  
arms.  
^ Scrape food from dishes before plac-  
ing in the dishwasher.  
Do not rinse dishes.  
^ Load dishes so that water can reach  
all surfaces. Do not place dishes and  
cutlery inside other pieces.  
^ Hollow items such as cups and  
glasses should be placed upside  
down in the upper basket.  
^ Concave based items, such as mugs  
or bowls, should be placed at an an-  
gle on top of the coffee bar, so that  
water does not pool.  
^ To ensure good water coverage tall,  
narrow, hollow pieces, such as a  
vase, should be placed in the center  
of the basket, rather than in the cor-  
ners.  
^ Small cups and glasses should be  
placed on the cup racks. Taller mugs  
and glasses can be placed beneath  
the rack.  
^ Place very small items in the cutlery  
tray or basket so they do not fall to  
the bottom of the wash cabinet.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Items not recommended for  
dishwashing  
Glassware:  
– There are no standard guidelines for  
washing glassware but, when in  
doubt wash by hand.  
– Cutlery with wooden handles.  
– Wooden cutting boards.  
– Wash delicate glassware with a low  
temperature program and without the  
extended drying feature to reduce  
the risk of clouding. See the "Pro-  
gram guide".  
– Glued items such as old knives with  
handles glued together around the  
shank of the blade.  
– Hand made craft items, antique,  
metal trimmed or decorative glass-  
ware.  
– If crystal or delicate glasses will be  
washed frequently, connect the dish-  
washer to cold, rather than hot water.  
– Lead crystal.  
– Clouding or etching may occur on  
glasses after frequent washing.  
– Copper, brass, tin or pewter.  
– Plastic items that are not heat resis-  
tant.  
– When purchasing new dishes,  
glasses and cutlery, make sure they  
are dishwasher safe.  
– Dishes with color painted over the  
glaze. These dishes may fade over  
time.  
Silver and aluminum:  
– Cast iron pots and pans.  
– Silver or aluminum items may tarnish.  
– Silverware previously cleaned with a  
silver polish may be damp or spotted  
at the end of a program where water  
has adhered to the polish. This can  
be rubbed off with a soft, dry cloth.  
Silver that has been cleaned in an  
immersion dip is usually dry at the  
end of a program, but may tarnish.  
– If left to dry, foods containing sulfur  
can discolor silver. These include  
egg yolk, onions, mayonnaise, mus-  
tard, legumes, fish, fish brine and  
marinades.  
– Silverware may tarnish or pit if  
washed next to stainless steel.  
Leave space between these metals.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Cutlery tray (SC units)  
Spoon heads should be placed in con-  
tact with at least one of the serrated re-  
tainers of the cutlery tray to ensure that  
water runs off freely.  
The removable cutlery tray makes un-  
loading flatware easy. Simply carry the  
cutlery tray to where the flatware is  
stored and put the entire basket away  
in one trip.  
For easier unloading cutlery should be  
grouped in zones, one for knives, one  
for forks, one for spoons, etc.  
Place knives with the cutting edge and  
forks with the prongs between the hold-  
ers. Spoons should be placed in the  
opposite direction with the handles be-  
tween the holders.  
Longer items such as soup ladles, cake  
slices, mixing spoons and long knives  
should be placed lengthwise in the in-  
dentation of the cutlery tray.  
Spoons with thick handles may have to  
be placed as knives and forks with their  
heads in the holders.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Upper basket  
Adjusting the upper basket  
On select models, the upper basket  
can be raised or lowered to accommo-  
date tall items.  
^ Slide out the upper basket.  
Load the upper basket with small, light-  
weight, or delicate items such as cups,  
saucers, glasses, dessert bowls and  
flat pans.  
Long items such as soup ladles, mixing  
spoons and knives can be set across  
the front of the upper basket.  
^ Pull up the levers at the sides of the  
upper basket and adjust the basket  
height.  
^ Release the levers and the basket will  
lock in place.  
The basket can also be angled to fit tall  
items in both, the lower and upper bas-  
kets. The angles should not be set to  
opposite extremes. This will block the  
middle spray arm. Take care when slid-  
ing the basket in and out in this posi-  
tion.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Adjustable cup racks  
Coffee bar  
Raise the rack to make room for tall  
glasses. Lower it to double stack  
smaller pieces.  
To allow water to run off the bottom of  
coffee mugs, place slanted on top of  
the coffee bar. The bar can also be  
used to separate two rows of glasses.  
To stack wide items, flip the bar to the  
right.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Lower basket  
Height limit  
For larger and heavier items such as  
plates, serving platters, sauce pans,  
bowls.  
Dishwasher with cutlery tray  
The guide at the front of the upper bas-  
ket determines the maximum height for  
items placed in the lower basket so that  
the middle spray arm is not blocked.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Lower basket inserts  
Various removable inserts are available for the lower basket to accomodate spe-  
cial items to be washed.  
Removing an insert  
^ To remove an insert, gently pull up on  
the handle.  
Inserting an insert  
^ Slid the hitches of the inset under the  
vertical struts of the lower basket.  
^ Push down on the handle to snap the  
insert into position.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Lower basket inserts  
Foldable spike insert  
A highly flexible design holds tableware  
securely. It can be folded out of the way  
for pots, pans and other large items.  
This insert secures plates and platters.  
Foldable spikes  
Two rows of spikes can be folded  
down, to create more room for larger  
dishware e.g. pots, pans and bowls.  
^ Press on the yellow levers, a, to fold  
down the spikes, b.  
^ Hook the foldable spike insert into the  
back right corner of the lower basket,  
the area marked in white.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Lower basket inserts  
PlateGuard Plus insert  
A unique design cradles plates at 3  
points and can be used for washing  
cups, glasses, plates, bowls and pots.  
^ Hook the PlateGuard Plus insert into  
the left half of the lower basket, the  
area marked in white.  
Bottle holder  
The bottle holder e.g. for milk or baby  
bottles, can be inserted into the bottom  
basket in more than one place. Position  
in any area marked white in the illustra-  
tion. Do not place the insert in the cor-  
ners of the lower basket, water cannot  
properly cover bottles in these areas.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Basket accessories  
Additional inserts for the upper and lower baskets may be purchased from your  
Miele dealer or the Miele Technical Service Department.  
Bottle holder  
to wash milk or baby bottles  
part # 03 857 850  
Glassware insert  
for the lower basket  
part # 01 145 642  
to wash a large number of glasses  
Glassware insert  
for the upper basket  
part # 03 636 034  
to wash long stemmed glassware  
PlateGuard insert  
part # 02 244 870  
to wash plates with a diameter  
up to 12 1/2" (32 cm)  
Cup rack for the  
PlateGuard insert  
part # 03 859 730  
to wash cups and stemware  
in the lower basket  
Small cutlery basket  
for the lower basket  
to wash additional cutlery  
part # 02 372 335  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Adding detergent  
,Dishwasher detergents contain  
irritant and corrosive ingredients.  
Keep children away from detergent.  
Do not fill the detergent dispenser  
until you are ready to start the dish-  
washer.  
Only use powder detergents or tab-  
lets formulated for residential dish-  
washers. The use of gel or liquid de-  
tergent is not recommended.  
Never fill the detergent dispenser to  
capacity.  
Do not use more than the recom-  
mended amount of detergent. Con-  
tinued use of too much detergent  
may cause machine damage.  
The horizontal marks in Compartment II  
indicate levels of approximately 1 1/4,  
1 3/4 and 2 tablespoons (20, 25 and  
30 ml) respectively.  
^ With the dishwasher door fully open  
fill compartment II with 2 tablespoon  
(30 ml) of powder detergent, or one  
detergent tablet.  
^ Close the cover. The cover will al-  
ways open at the end of a wash pro-  
gram except in "Rinse & Hold".  
2 tablespoon (30 ml) of detergent is  
enough for most normally soiled loads.  
For heavily soiled loads, or if food has  
dried on the dishes, a program contain-  
ing a prewash cycle should be se-  
lected. Add an extra tablespoon (15 ml)  
of detergent to compartment I.  
Less detergent is needed in homes with  
very soft water and when washing  
lightly soiled dishes.  
^ To open, press the latch on the deter-  
gent dispenser.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Running the dishwasher  
Waterproof System  
^ Make sure the spray arms are not  
blocked.  
All Miele dishwashers are specially de-  
signed to shut off the water intake and  
drain the wash cabinet in the rare event  
of an internal water valve failure.  
^ Close the door.  
^ Turn on the dishwasher.  
The "Start" indicator (19) will flash.  
For this feature to be active, the ma-  
chine must be "On" (not necessarily  
running) and the door must be closed.  
^ Select a wash program by turning the  
program selector (17) to the left or  
right. Refer to the "Program guide" for  
details.  
Program sequence indicator  
(14)  
^ Select "Delay Start" or "Top Solo" if  
desired. See "Additional features".  
The current step of the program is indi-  
cated by one of the program sequence  
indicators (14).  
^ Press the "Start" button (19).  
The program will begin.  
Do not end a program prematurely!  
Important program steps could be  
omitted (e. g. reactivating the water  
softener).  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
At the end of a program  
Interrupting a program  
The "End" indicator will light when the  
program has finished.  
A program is interrupted as soon as the  
door is opened.  
If the door is closed, the program will  
continue from where it was interrupted.  
^ Turn the program selector (17) to  
"Stop".  
,Water in the dishwasher may be  
hot. There is a danger of being  
burned!  
Only open the door if absolutely  
necessary.  
The "End" (14) indicator will go out and  
the "Start" (19) indicator will flash.  
^ Press the "On/Off" (13) button.  
The "Start" (19) indicator will go out.  
^ Open the dishwasher door slightly to  
allow the dishes to cool before un-  
loading.  
Changing a program  
It is advisable to turn off the water  
supply if the dishwasher will not be  
used for a period of time (e.g. while  
vacationing).  
If a program is running:  
^ Turn the program selector (17) to  
"Stop" for at least one second.  
^ Turn the program selector (17) to the  
new program.  
^ Select "Top Solo" and "Delay Start" if  
needed (see "Additional features").  
^ Press the "Start" (19) button to begin  
the wash program.  
If a program has not started:  
^ Turn the program selectro (17) to the  
new program.  
^ Select "Top Solo" and "Delay Start" if  
needed (see "Additional features").  
^ Press the "Start" (19) button to begin  
the wash program.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Program guide  
Program  
When to use  
Program cycle  
Pre- Main Interim Final Dry-  
wash wash rinse rinse ing  
1 2  
1 2  
Pots & Pans for heavily soiled pots and pans with dried on food X X  
Main wash temperature 170 °F (75 °C)  
X
X
X
-
X
X
X
X
Run-time 128 min  
Sani Wash  
extended wash time  
-
X
X X  
for sanitizing normally soiled dishware with dried  
on food  
Main wash temperature 150 °F (65 °C)  
Run-time 142 min  
Economy  
energy saving program  
X
X
-
X
X
for normally soiled dishware  
Main wash temperature 130 °F (55 °C)  
Run-time 85 min  
Energy Saver for light to normally soiled dishware,  
only use, if the dishwasher is connected to hot water  
X X  
X X  
X
X
X
X
-
-
X
X
X
X
Run-time 65 min  
Normal Plus higher wash temperature helps to clean  
normally soiled dishware with stubborn dried on  
food or greasy residues  
Main wash temperature 150 °F (65 °C)  
Run-time 135 min  
1)  
Normal  
for normal soiled dishware  
Main wash temperature 130 °F (55 °C)  
Run-time 118 min  
X X  
X
X
X
-
X
X
X
X
China &  
Crystal o  
"Gentle program"  
-
X
X
X -  
for lightly soiled and heat sensitive tableware  
Main wash temperature 115 °F (45 °C)  
Run-time 72 min  
Rinse & Hold for rinsing dishes when a complete cycle is not needed -  
Run-time 11 min  
1) Standard for Energy Label  
When washing a full load in Pots & Pans, Sani Wash and the Normal programs use at least 2 table-  
spoons (30 ml) of detergent.  
For the Pots & Pans program add an additional teaspoon (5 ml) to compartment I.  
1
If "Top Solo" is selected, reduce the amount of detergent to 1 / tablespoons (20 ml).  
4
Program times are based on a hot water connection. If the unit is connected to cold water, program  
times will increase by approximately 25 minutes.  
Usage:  
Electric 0.06 - 2.4 (kWh)  
Water  
1.3 - 6.3 US gallons (5 - 24 L)  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Additional features  
"Top Solo" (15)  
Using "Top Solo" will save water and  
energy.  
^ Turn the dishwasher on using the  
"On/Off" (13) button.  
This program is recommended when  
there is only a small load to clean. "Top  
Solo" can be selected with all pro-  
grams.  
The "Start" (19) indicator will flash.  
^ Turn the program selector (17) to the  
left or right to the desired program.  
^ Press the "Top Solo" (15) button.  
With this feature, water is directed only  
to the top and middle spray arms in the The "Top Solo" (15) button will light.  
dishwasher. This means that the water  
^ "Delay Start" may also be selected at  
jets are only aimed at items in the up-  
this time (see next page).  
per basket and the cutlery tray.  
^ Press the "Start" (19) button.  
The middle spray arm also directs  
The program will begin.  
water downwards, so lightly soiled  
plates or platters can be placed in the  
lower basket.  
When using this program, do not place  
pots, bowls or other hollow containers  
in the lower basket.  
Because a smaller load is being  
washed the amount of detergent rec-  
ommended can be reduced to 1 1/4  
tablespoons.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Delay Start (18)  
^ If the "Delay Start" d (18) button is  
pressed after the 9 hour mark the de-  
lay start feature will be cancelled.  
Delay Start will have to be reselected.  
The start time of a program can be de-  
layed from 1 to 9 hours.  
The delay start is set in one hour steps.  
^ The "Top Solo" feature may also be  
selected at this time (see previous  
page).  
,When using delay start, make  
sure the detergent compartment is  
dry before adding detergent. Wipe  
dry if necessary.  
^ Press the "Start" button (19).  
The "Start" (19) indicator will light.  
^ Turn on the dishwasher with the  
"On/Off" (13) button.  
The delay start will count down in  
one-hour-steps.  
The "Start" (19) indicator will flash.  
Once the delay start period has  
elapsed, the selected program will be-  
gin automatically.  
^ Turn the program selector (17) left or  
right to the desired program.  
^ Press the "Delay Start" (18) button.  
1 appears in the delay start display  
(16). A delay start time of one hour is  
set.  
^ Press the "Delay Start" (18) button un-  
til the desired delay start time ap-  
pears in the display (16).  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
To start a program before the delay  
start period has elapsed:  
^ Turn the program selector (17) to  
"Stop" for at least one second.  
The delay start display (16) will go out.  
^ Turn the program selector (17) to the  
desired program.  
^ Select "Top Solo" again, if needed.  
^ Press the "Start" button (19).  
The program will begin.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
Extended drying  
^ Turn the program selector to the  
"9 o’clock" position.  
If desired drying results are not consis-  
tently achieved, the turbothermic cool-  
ing fan can be programmed to run an  
extra 14 minutes at the end of each  
program.  
If the "Top Solo" indicator is not lit:  
the extended drying time is off.  
If the "Top Solo" indicator is lit:  
the extended drying time is on.  
The "Extended drying" feature can also  
be activated to prevent condensation  
from collecting on the steam deflector.  
If the the correct drying time is set:  
^ Turn off the dishwasher.  
Turning extended drying on/off  
^ Turn off the dishwasher.  
If the drying time is incorrect:  
^ Turn the program selector to "Stop".  
^ Press the "Top Solo" button, to  
change the setting.  
^ Press and hold the "Top Solo" button  
and at the same time turn the dish-  
washer on using the "On/Off" button.  
Release the "Top Solo" button within  
two seconds.  
According to the previous setting the  
"Top Solo" indicator will go on or off.  
^ Turn the program selector to "Stop".  
The "Salt" indicator will flash.  
The changed extended drying option is  
stored.  
If the "Rinse aid" indicator is lit, the rinse  
aid dispenser needs to be refilled.  
^ Turn off the dishwasher.  
If any other indicator is lit or flashing,  
the above steps must be repeated.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Frequently asked questions  
With the aid of the following guide, minor problems can be fixed without a service  
call.  
,Repairs should only be carried out by a qualified and trained person in ac-  
cordance with local and national safety regulations. Unauthorized repairs could  
cause personal injury or machine damage.  
What if …  
Possible fault  
Fix  
the dishwasher does not The door is not properly  
Close the door firmly.  
start?  
closed.  
The machine is not  
plugged in.  
Insert the plug.  
The fuse is defective or  
the breaker has tripped.  
Reset the circuit breaker.  
Make sure it is a 15 A  
breaker.  
the dishwasher does not The program selector is  
start, after pressing the set to "Stop".  
"Start" button and  
Turn the program selec-  
tor to the desired pro-  
gram.  
the "Start" indicator  
flashes?  
Press the "Start" button.  
the dishwasher stops  
during a program?  
The fuse or breaker has  
tripped.  
Reset the circuit breaker.  
Make sure it is a 15 A  
breaker.  
the "Intake/Drain" indi- The intake water has not Start the program  
cator comes on during  
reached the required tem-  
again.  
the "Energy Saver" pro- perature of 115 °F/45 °C,  
If the indicator light co-  
mes on again, select a  
different program.  
gram?  
the hot water system may  
be overloaded, see "Pro-  
gram guide".  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Frequently asked questions  
What if …  
Possible fault  
Fix  
the "Intake/Drain" indi- The water valve is closed. Open the water valve.  
cator is lit or flashing  
and the dishwasher may  
have stopped?  
The filter in the water inlet See maintenance instruc-  
is blocked.  
tions.  
The flow pressure at the  
water inlet is less than  
4.5 psi (0.3 bar).  
Contact a plumber.  
The waterproof system  
has activated.  
Call the Miele Technical  
Service Department.  
the "Drain" indicator  
flashes and the program  
stops?  
Water intake error.  
Turn off the dishwasher  
before fixing a problem.  
Open the water valve.  
Check and clean the  
water intake filter, see  
maintenance instruc-  
tions.  
The flow pressure at the  
water inlet is less than  
4.5 psi (0.3 bar). Con-  
tact a plumber.  
Drain error, water left in  
the wash cabinet  
Turn off the dishwasher  
before fixing a problem.  
Clean the triple filter,  
see maintenance in-  
structions.  
Clean the drain pump  
and the non-return  
valve, see maintenance  
instructions.  
Remove any kinks in  
the drain hose.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Frequently asked questions  
What if …  
Possible fault  
Fix  
the "End", "Start" and  
"Top Solo" indicators  
flash at the same time at  
the end of a program?  
There may be a technical Turn the program selec-  
fault.  
tor to "Stop".  
Turn off the dishwasher.  
A few seconds later:  
Turn the dishwasher on.  
Select the desired pro-  
gram.  
Press the "Start" button.  
If the indicators flash  
again, there is a technical  
problem.  
Call the Miele Technical  
Service Department.  
there is a knocking  
noise in the wash cabi- an item in the basket.  
net?  
The spray arm is hitting  
Interrupt the program, re-  
arrange items blocking  
the spray arms.  
there is a rattling noise? Items are not secure in  
Interrupt the program and  
rearrange loose pieces.  
the wash cabinet.  
there is a knocking  
noise in the water  
pipes?  
This may be caused by  
the installation or the di-  
ameter of pipe.  
This has no effect on the  
dishwasher. If in doubt  
contact a plumber.  
the dishes are not dry,  
The rinse aid setting may Increase the dosage or  
glasses and cutlery are be too low, or the rinse aid refill the reservoir, see "Be-  
spotted?  
reservoir is empty.  
fore using for the first  
time".  
Extended drying is not ac- Activate the Extended  
tivated. drying feature.  
Dishes were taken out too Leave dishes in longer.  
soon.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Frequently asked questions  
What if …  
Possible fault  
Fix  
dishes are not clean?  
The dishes were not  
loaded correctly.  
See, "Loading the dish-  
washer".  
The program was not  
powerful enough.  
Select a more intensive  
program see, "Program  
guide".  
Not enough detergent  
was dispensed.  
Use more detergent, see,  
"Adding detergent".  
The spray arm jets are  
clogged.  
Clean the spray arm jets,  
see, maintenance instruc-  
tions.  
The triple filter is clogged Clean and reseat the filter,  
or not correctly seated.  
see, maintenance instruc-  
tions.  
tea or lipstick stains  
have not been com-  
pletely removed?  
The wash temperature of Select a program with a  
the selected program was higher temperature.  
too low.  
Not enough detergent  
was used.  
Use more detergent.  
white residue is visible Not enough rinse aid was Increase the dosage,  
on cutlery and dishes,  
clouding occurs on  
glassware and film can  
be wiped off?  
used.  
see "Before using for the  
first time".  
The salt reservoir is  
empty.  
Add reactivation salt,  
see "Before using for the  
first time".  
The salt reservoir cap was Reseat it making sure it  
not correctly screwed on. screws back on correctly.  
The programmed setting Adjust the setting of the  
of the water softener is too water softener , see "Be-  
low.  
fore using for the first  
time".  
there is a bluish sheen  
on the surface of  
glasses and film can be  
wiped off?  
The rinse aid dosage is  
set too high.  
Reduce the dosage, see  
"Before using for the first  
time".  
glasses are dull and dis- Glasses are not dish-  
colored and film cannot washer safe.  
be wiped off?  
There is no remedy.  
Only wash dishwasher  
safe glasses.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Frequently asked questions  
What if …  
Possible fault  
Fix  
plastic items are discol- Natural dyes e. g. from  
ored? vegetables may be the  
Use more detergent, see  
"Adding detergent".  
cause. Not enough deter- Discoloration is perma-  
gent was used to break  
down natural dyes.  
nent.  
there are rust stains on The salt reservoir cap was Reseat and screw the cap  
cutlery?  
not screwed on properly. on firmly.  
The affected items are not There is no remedy.  
corrosion resistant.  
Only wash dishwasher  
safe cutlery.  
detergent is left in the  
The dispenser was damp Dry the dispenser before  
dispenser at the end of a when detergent was  
program? added.  
the detergent dispenser Detergent residue is  
adding detergent.  
Remove the residue.  
lid can not be closed  
properly?  
blocking the catch.  
water remains in the  
The triple filter in the wash Clean the filter,  
wash cabinet at the end cabinet is clogged.  
of a program?  
see maintenance instruc-  
tions.  
The drain pump or the  
Clean the drain pump and  
non-return valve may be the non-return valve,  
blocked.  
see maintenance instruc-  
tions.  
The drain hose is kinked. Remove the kink.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
After sales service  
In the event of a fault which you cannot  
correct yourself please contact:  
Program update function - PC  
The Program Correction (PC) allows a  
technician to update the dishwasher to  
make use of new technology.  
– Your Miele Dealer  
or  
– The Miele Technical Service Depart-  
ment.  
USA 1-800-999-1360  
CDN1-800-565-6435  
When contacting the Miele Technical  
Service Department, please quote the  
model and serial number of your appli-  
ance.  
These can be found on the data plate  
on the upper inside edge of the dish-  
washer door.  
For example, if a detergent with good  
wash results using only cold water be-  
comes available, the wash programs  
can be modified to take advantage of  
this.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Transport  
To transport the dishwasher, e. g. when  
moving to a new home, note the follow-  
ing:  
– Empty the dishwasher.  
– Secure any loose parts, e. g. hoses,  
cables, cutlery baskets.  
– Transport the dishwasher in the up-  
right position.  
If unavoidable it may be transported  
on its back.  
Do not transport it on its side or on  
the door. Residual water in the ma-  
chine could leak and cause electrical  
damage.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Maintenance Instructions  
To prevent accidents  
and machine damage,  
read these instructions  
before  
installation or use.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Triple filter system  
The triple filter system in the base of the  
wash cabinet prevents food from being  
redeposited on dishes. It also protects  
the circulation pump from damage  
caused by foreign objects (e.g. broken  
glass, bones).  
The filter system should be cleaned ev-  
ery 4 - 6 months or whenever a foreign  
object is trapped.  
Cleaning the filter in the wash  
cabinet  
^ Lift the filter out of the machine. Re-  
move any solid particles and rinse  
under running water. Scrub with a ny-  
lon brush if necessary.  
^ Turn off the dishwasher before clean-  
ing.  
^ Turn the handle counterclockwise to  
release the triple filter system.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
To clean the underside of the filter, the  
flap must be opened:  
^ Return the filter so it lies flat in the  
base of the wash cabinet.  
^ Pull back the yellow clip.  
^ Lock the filter by turning the handle  
clockwise.  
^ Rinse all parts under running water.  
Scrub with a nylon brush if neces-  
sary.  
,The dishwasher must not be  
used without the filter locked in  
place.  
^ Close the flap so that the clip en-  
gages.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleaning the spray arms  
^ Remove the lower basket.  
Sometimes particles of food get stuck  
in the spray arm jets. The spray arms  
should be inspected and cleaned every  
4 - 6 months.  
^ Turn off the dishwasher before clean-  
ing.  
Remove the spray arms as follows:  
^ Remove the cutlery tray (if present).  
^ Press the top spray arm upwards to  
engage the inner ratchet and un-  
screw the spray arm.  
^ Pull the lower spray arm firmly up-  
wards to remove.  
^ Lift up the middle spray arm, a, to  
engage the ratchet and unscrew the  
spray arm, b.  
^ Use a pointed object such as a tooth-  
pick to push food particles into the  
spray arm jets.  
^ Rinse thoroughly under running  
water.  
^ Return the spray arms and check  
that they rotate freely.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning the wash cabinet  
Cleaning the exterior  
Generally, the wash cabinet is self  
cleaning if the correct amount of dish-  
washer detergent is used.  
,Never use abrasive cleaners,  
scouring pads, steel wool or caustic  
(oven) cleaners on the dishwasher.  
They will damage the surface.  
The wash cabinet can be cleaned with  
a dishwasher cleaner such as Dis  
Cleaner available from your Miele  
dealer or the Miele Technical Service  
Department.  
Plastic  
All plastic surfaces and the control  
panel can be cleaned with warm water  
and liquid dish soap applied with a soft  
sponge.  
Cleaning the door and door  
seal  
Wipe dry using a soft cloth.  
^ Wipe the door seal with a damp cloth  
to remove any food particles.  
,Do not use too much water when  
cleaning the controls. Water could  
penetrate into the electronics and  
cause damage.  
^ Food residue and spilt liquids should  
be wiped from the sides of the dish-  
washer door. These are outside of the  
wash cabinet and are not cleaned by  
water from the spray arms.  
Stainless steel  
Stainless steel surfaces can be cleaned  
using a non-abrasive stainless steel  
cleaner.  
To help prevent resoiling, a conditioner  
for stainless steel can also be used.  
Apply sparingly with even pressure.  
Stainless steel colored controls  
These controls may become discolored  
or damaged if not cleaned regularly.  
Do not use a stainless steel cleaner on  
the knobs or buttons.  
Wood  
Panels made from wood should be  
cleaned using a soft damp cloth and an  
appropriate wood cleaner.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning the water inlet filter  
,The plastic valve housing on the  
intake hose contains electrical com-  
ponents and should not be im-  
mersed, or run through water.  
A filter is incorporated in the intake  
hose attached to the dishwasher’s shut  
off valve. If your water is hard, or the  
pipes contain sediment, this filter may  
clog and prevent enough water from  
entering the wash cabinet.  
Cleaning the filter:  
^ Disconnect the dishwasher from  
electricity (unplug it or "trip" the cir-  
cuit breaker).  
Installing an in-line water filter  
^ If your water contains a large number  
of insoluble substances, a filter be-  
tween the water valve and the intake  
hose connection is recommended.  
These filters can be purchased from  
Miele’s Technical Service Depart-  
ment.  
^ Turn off the water valve.  
^ Unscrew the intake hose.  
^ Carefully remove the rubber seal.  
^ Remove the filter using a needle nose  
plier and rinse under running water.  
^ Return the filter and seal. Make sure  
they are seated correctly.  
^ Screw the intake hose back on the  
water valve, checking that it is not  
cross-threaded.  
^ Slowly turn on the valve and test for  
leaks.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning the drain pump and  
non-return valve  
If the dishwasher is not completely  
drained at the end of a program, the  
drain pump or non-return valve may be  
blocked.  
^ Turn off the dishwasher.  
^ Remove the triple filter (see "Cleaning  
the filter in the wash cabinet").  
^ Use a jug or bowl to scoop water out  
of the wash cabinet.  
^ Pull out the non-return valve and  
rinse well under running water.  
^ Tilt the locking clamp to the side.  
The drain pump is beneath the non-re-  
turn valve (see arrow).  
^ Before returning the non-return valve,  
check that the drain pump is not  
blocked. Spin the propeller several  
times in both directions to check for  
obstructions.  
^ Carefully refit the non-return valve  
and secure it with the locking clamp.  
^ Refit and lock the filter in place.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Alterations rights reserved (G 856 / G 857 Plus) / 000  
2501  
This bio-friendly paper was bleached without the use of chlorine.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Refrigerator KFN 14947 SDE ed cs User Manual
Mr Handsfree Bluetooth Headset GBNLFRDKCZSKEI User Manual
Multiquip Portable Generator GA45R User Manual
NETGEAR Switch GS108PE 100NAS User Manual
Neuro Logic Systems Mouse 17 User Manual
Nikon Digital Camera SB2F01 11 User Manual
Norcold Refrigerator N260 User Manual
Onkyo Stereo Receiver TX NR708 User Manual
Optimus Home Theater System PRO SWS 502 User Manual
Panasonic MP3 Player SV SW30V User Manual