21A2677
FIRST
CLASS
STAMP
HERE
MODEL520W, 620W, and 820W
4545 E BASELINE RD
PHOENIX AZ 85040-6400
IN-WALLLOUDSPEAKER
OWNERS MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER HOME AUDIO PRODUCTS FROM MTX
MTX offers a wide assortment of audio components. Ranging from in-ceiling
speakers to amplifiers to accessories. Each component is value engineered and
must meet strict quality control standards before it becomes part of the MTX
product line.
LOUDSPEAKER PLACEMENT
Blueprint Series Loudspeakers are designed to work within any interior
decorating scheme. They can be installed in virtually any location where flush
mounting is possible. To maximize their sound performance however certain
guidelines should be followed. For the best stereo reproduction the two
loudspeakers should be placed an equal distance from your listening position
and separated so that the angle between them, at the listening position, is
Listed below you will find a sampling of components available from your
authorized MTX dealer.
LPS-600
Speaker/Amplifier Selector
Accommodates up to 6 pair of speakers
Handles up to 250 watts/channel continuous (RMS)
Impedance Protection Circuitry
Accommodates up to 14 gauge wire
MODELMP42
For best stereo imaging, we recommend that the units be placed so that the
tweeters are as close as possible to the ear level of a seated listener.Asthisis
not always possible in keeping with aesthetic design of a particular room,
MODEL520W, 620W, and 820W In-Wall Loudspeakers were designed with a
pivoting tweeter which rotates to allow you to “aim” the high frequencies
Multi-Purpose Loudspeaker
Two 4” W oofers, with 1/2” Balanced Dome Tweeter
50W atts RMS/200 W attsTotal Power Handling
Magnetically shielded, weather resistant
Sleek, Euro-style design
Available in white or black
12.6” x 4.8” x 4.9”
PS15
15” Powered Subwoofer System
200 W att Class D Switching Power Amplifier
Infrared Remote Control for Volume Function
Magnetically Shielded, Downfiring Subwoofer in small enclosure
Signal Sensing Auto Turn On
Red LED Clipping Indicator
Normal Dispersion
Dispersion After Tweeter Adjustment
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP1
STEP4
Using a stud finder (available at low cost at most hardware stores) or other
accurate method, locate center point between two studs and mark. Using
template provided, trace hole pattern on surface of wall. Placing a bubble level
on either the horizontal or vertical guidelines of template will assist you in
Attach loudspeakers wires to speaker terminals, observing correct polarity
(positive to positive and negative to negative), and position panel and frame
assembly to hole as shown. Insert top of mounting frame into hole at top. By
moving bottom of frame upwards, you should now be able to insert bottom of
frame into hole at bottom. Be careful not to pinch loudspeaker wires in the
process. Tighten long screws. Use a level during tightening to insure
STEP2
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in wall,
STEP5
After speaker panel is secured tightly,testforsound.
STEP6
When you are satisfied the speaker is operational, “aim” the tweeter,andaffix
grill.As grill is designed for a snug fit, you’ll need to position one edge into
slot first, and press or squeeze around perimeter of grill, while pushing leading
edgesintogrillslot.
STEP3
Run loudspeaker wires to sound source location. There are several methods you
can use to accomplish wiring, depending on the construction characteristics of
the room or house. You can add a professional touch to your installation by
using a speaker terminal plate at the source location. Leave sufficient amount
Download from Www.Somanuals.com. All Manuals Search And Download.
|