NOVEMBER 2000
16-40089-101
Game Operations
Manual for 27”
Dedicated Video
Game
Manual Includes
Operation & Adjustments * Parts Information * Wiring Diagrams * Testing & Problem Diagnosis
The manufacturer intends that this game is to be operated for amusement purposes only and not in contravention of
any federal, state or local law or regulation of the United States or any foreign country governing gaming devices. All
operators of this game are responsible for its operation in accordance with such laws and regulations. The manufac-
turer's factory settings for this game may require adjustment in order to comply with laws applicable in an operator's
specific jurisdiction. It is the operator's responsibility to determine whether adjustments are necessary and, if they are,
to make the appropriate adjustments prior to operating the amusement game.
MIDWAY AMUSEMENT GAMES, LLC
3401 NORTH CALIFORNIA AVENUE CHICAGO, ILLINOIS 60618 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
CABINET LINKING INSTRUCTIONS
To link two cabinets, use the crossover coupler included in the spare parts bag. Connect
the factory installed linking cable to the coupler and follow the instructions for “Wiring
Modifications and Software Setup” located below starting with step #7.
To link three or more cabinets, use a standard 10 base-T ethernet hub and follow all of
the instructions for “Wiring Modifications and Software Setup” located below.
CABINET ARRAYS
To create a Video Game Machine (VGM) Array, join the cabinets together. Each VGM comes equipped
with the necessary hardware to connect cabinets and provide maximum stability. Hardware is located in
the spare parts bag inside the cash box.
To join cabinets, remove the flat-head carriage bolts from the top and rear of adjacent cabinet sides. Posi-
tion cabinets next to one another and adjust the leg levelers until all holes are aligned. Insert long carriage
bolts through the holes in both cabinets, and then fasten in place with the nuts provided.
NETWORK CONSIDERATIONS
Each VGM comes complete with a factory installed network cable. Optionally, a hub can be installed and
located remotely to monitor network activity. Cables up to 328 ft., or 100 meters, in length may be used in
conjunction with the hub provided they are Category 3 or higher, 100 ohm unshielded twisted pair commu-
nications grade wiring. Standard telephone cables are not sufficient for this application and should not be
used.
Take care to protect exposed wiring from player foot traffic, cleaning crews, service personnel, etc. Use
approved conduit or wire channels to support cables. Please note that modular connectors do not have
strain relief.
Prevent linking cables from becoming damaged by avoiding sources of extreme heat or moisture, and high
amounts of electrical energy like neon signs, fluorescent fixtures, two-way radios, cordless phones, power
circuits, public address system wiring, etc.
Universal RJ-45 modular plugs are not numbered or coded in any way. Clearly label all network connec-
tions to avoid confusing network cables with computer or telephone circuits.
WIRING MODIFICATIONS AND SOFTWARE SETUP
1. Place the linking hub inside the base of a cabinet nearest the center of the array. Remember that the
crossover couplers supplied with the game are not used when creating an array using the hub. Cross-
over couplers are only used to link two cabinets.
2. Unlock and remove the rear door from the cabinets selected to be part of the array. Inside the cabinet
you will find a coil of linking cable with one end already attached to game electronics. Uncoil just
enough of the cable to reach the hub, then recoil the rest of the cable and tie it in place. Repeat this
procedure for each of the other cabinets. Do not reinstall the cabinet door(s) at this time.
3. Route the free end of each cable out through the notch located in the rear door opening and plug into
any jack on the rear panel of the linking hub. Route the free end of the AC adapter for the hub and plug
it into the 9VAC jack on the front panel of the hub. Now all of the cables can be connected to the hub.
ARCTIC THUNDER
V
Download from Www.Somanuals.com. All Manuals Search And Download.
LNK
X
4. Refer to the manufacturer’s instructions in order to set the hub switches for
(link) and (cross-
over) activity.
5. Fasten the hub to the bottom of the most central cabinet using a hook-and-loop type material. Orient
the hub so that the indicator lights are visible and cable jacks are accessible.
6. Make sure excess cable is tied into a coil and that all cables are routed through the notch in the rear
door. Connect the AC adapter for the hub and all line cords to AC power.
CAUTION
Do not connect or disconnect any cable to the game electronics or hub with the power turned
on. Circuit disruptions may damage the game and void the warranty.
7. Switch on power and closely observe the screen for each cabinet during start up. Each automatically
Troubleshooting
enters ATTRACT MODE if no errors are found. Refer to
errors are detected.
in the operation manual if
8. Verify software version compatibility for each game machine. Newer versions may contain instructions
previous versions do not, causing games to halt or reset at random.
Unlock the coin door for each cabinet to access the operator control buttons inside coin vault. Press
and hold the TEST button to enter the menu system. Select SYSTEM INFORMATION MENU at the
Main Menu screen. Scroll to SOFTWARE VERSION and press the TEST button. Observe screen for
desired information
9. Assign game machine a link number. Select ADJUSTMENTS from the Main Menu screen. Scroll to and
select GAME LINK NUMBER by pressing the Test button. Assign a linking number ranging from 1 to 4
to each game cabinet.
NOTE:
Each cabinet must have its own individual and unique number. The first cabinet on the left is
always cabinet 1, the second is cabinet 2, etc.
10. Repeat these steps for each remaining game cabinet you wish to link.
11. Close and lock the coin door, and reinstall and lock the rear door for each cabinet. Lower the leg level-
ers for each cabinet until the casters do not touch the floor and the cabinets are level. Lock the levelers
in position by tightening the nuts provided.
VI
IDWAY MUSEMENT AMES
, LLC
M
A
G
Download from Www.Somanuals.com. All Manuals Search And Download.
|