OPERATORS AND PARTS MANUAL NO. 04-01-9100
FOR
9100 SERIES
“BOSS”
REAR UNLOAD FORAGE BOX
TRUCK AND TRAILER
MODELS:
9122
9126
9130
9136T
9124
9128
9130T
DO NOT OPERATE EQUIPMENT UNTIL THIS MANUAL HAS BEEN READ AND UNDERSTOOD.
MANUFACTURED BY
County Hwy. A West
P.O. Box 405
Dorchester, Wisconsin 54425-0405
Phone 715-654-5132 • FAX 715-654-5513
1-800-325-9103
E-mail: [email protected]
08/04
Download from Www.Somanuals.com. All Manuals Search And Download.
01/01/00
NEW MEYER REAR UNLOAD FORAGE BOX
MANUFACTURER’S WARRANTY
I.
The “Product Registration & Inspection Certificate” along with the original billing invoice “Owners Registration Form” must
be completed in full and promptly returned to Meyer Mfg. Corp. for this warranty to become both valid and effective. All war-
ranties on New Meyer Forage Boxes shall apply only to the original retail customer from an authorized Meyer Mfg. Corp.
dealership.
II.
This warranty shall not apply to any Meyer Forage Box which has been subjected to misuse, negligence, alteration, acci-
dent, incorrect operating procedures, or which shall have been repaired with parts other than those obtained through Meyer
Mfg. Corp.
III.
Meyer Mfg. Corp. warrants New Meyer Forage Boxes to be free from defects in material and workmanship under recom-
mended use and maintenance service, as stated in the Operator’s and Parts Manual," as follows:
A. Meyer Mfg. Corp. will repair or replace F.O.B. Dorchester, WI, as Meyer Mfg. Corp. elects, any part of a new Meyer
Forage Box which is defective in material or workmanship:
1. Without charge for either parts or labor during the first (1) year from purchase date to the original retail
customer.
2. Without charge for parts only during the second (2) year from purchase date to the original retail cus-
tomer.
B. In addition to the above basic warranty, Meyer Mfg. Corp. will repair or replace F.O. B. Dorchester, WI as Meyer Mfg.
Corp. elects:
1. Any part of the following which is defective in material or workmanship (not neglect to recommended
use and service) without charge for parts only (not labor) during the stated time periods from date of
purchase to the original retail customer:
Five (5) Years: The D667XH pintle main apron chain assembly.
2. Any part of the following which is defective in material or workmanship (not neglect to recommended
use and service) with a “pro-rated” charge for parts only (not labor) during the stated time period from
date of purchase to the original retail customer:
Ten (10) Years: a. The all welded steel frame box structure.
IV.
V.
COMMERCIAL USE: Coverage as in paragraph III A1 ONLY, except warranty coverage is for (90) days for parts and labor
to the original commercial retail customer.
Repairs eligible for labor warranty must be made by Meyer Mfg. Corp. or an authorized Meyer dealership. The original retail
customer is responsible for the transportation of the forage box to the dealership for warranty service or for any service call
expenses.
VI.
Except as stated above, Meyer Mfg. Corp. shall not be liable for injuries or damages of any kind or nature, direct, conse-
quential, or contingent, to persons or property. This warranty does not extend to loss of crop or for any other reasons.
VII. No person is authorized to give any other warranties or to assume any other obligation on Meyer Mfg. Corp.’s. behalf unless
made or assumed in writing by Meyer Mfg. Corp. This warranty is the sole and exclusive warranty which is applicable in con-
nection with the manufacture and sale of this product and Meyer Mfg. Corp.’s responsibility is limited accordingly.
Optional Equipment-Tarp, scales etc. warranty-See original equipment warranty.
--2--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
INTRODUCTION
Congratulations on your purchase of a new Meyer Rear
Meyer Manufacturing Corporation reserves the right to
make improvements in design, or changes in specifica-
tions at any time, without incurring any obligation to own-
ers of units previously sold.
Unload Forage Box. Undoubtedly you have given much
consideration to your purchase and we’re proud that you
have selected Meyer. Pride in craftsmanship, engineer-
ing and customer service have made Meyer products the
finest in the farm equipment industry today.
This supersedes all previous published instructions.
The Model 9100 is available as a truck/trailer mounted
unit or mounted to a wagon running gear pulled and pow-
ered by a farm tractor. When the PTO is referred to, it
means power takeoff from the truck.
The Model 9100 may be referred to as rear unload box,
forage box, box or rear unload forage box in this manual.
IMPORTANT:
At the front of this manual is a Product Registration and
Inspection Certificate. Be sure your dealer has com-
pleted this certificate and promptly forwarded a copy to
Meyer Manufacturing to validate the manufacturer’s
warranty. The product model and serial number are re-
corded on this certificate and below for proper identifica-
tion of your Meyer Forage Box by your dealer and the
manufacturer when ordering repair parts. The serial
number is stamped in the front upright of the left-hand
side.
This SAFETY ALERT SYMBOL means ATTEN-
TION! BE CAREFUL! YOUR SAFETY IS INVOLVED! It
stresses an attitude of HEADS UP FOR SAFETY. When
you see this symbol, be alert to the possibility of PER-
SONAL INJURY and carefully read the message that fol-
lows.
WARNING: NEVER OPERATE WITHOUT ALL
COVERS, SHIELDS AND GUARDS IN PLACE. KEEP
HANDS, FEET AND CLOTHING AWAY FROM
MOVING PARTS. SOME COVERS AND GUARDS
HAVE BEEN REMOVED FOR ILLUSTRATIVE PUR-
POSES ONLY IN THIS MANUAL. FAILURE TO HEED
MAY RESULT IN SERIOUS PERSONAL INJURY OR
DEATH.
Model No.___________________________________
Serial No.___________________________________
Date of Purchase_____________________________
There is no substitute for quality. That is why thousands
of people like you have purchased Meyer farm equip-
ment. They felt it was the best equipment to serve their
farming needs, now and in years to come. We ask that
you follow our policy of “safety first,” and we strongly
suggest that you read through the owner’s manual be-
fore operating your Meyer farm equipment.
At the back of this manual is the repair parts section. All
replacement parts are to be obtained from or ordered
through your Meyer dealership. When ordering repair
parts, refer to the parts section and give complete infor-
mation including quantity, correct part number, detailed
description and even Model No. and Serial No. of the for-
age box which needs repair parts.
Meyer Manufacturing Corporation wants to thank you for
not compromising quality. We are determined to offer ex-
cellence in customer service as well as provide you with
the very best value for your dollar.
NOTE: All references to right hand (RH) , left hand (LH),
front and rear apply to the product as viewed from the
rear of the box.
You are urged to study this manual and follow the in-
structions carefully. Your efforts will be repaid in better
operation and service as well as a savings in time and re-
pair expense. Failure to read this manual and under-
stand the machine could lead to serious injury. If you do
not understand instructions in this manual, contact either
your dealer or Meyer Manufacturing Corp. at
Dorchester, WI 54425.
Sincerely,
All Employees of
MEYER MANUFACTURING CORPORATION
9100 Rear Unload
--3--
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
THIS SYMBOL IS USED TO CALL ATTENTION TO INSTRUCTIONS CONCERNING PERSONAL SAFETY.
BE SURE TO OBSERVE AND FOLLOW THESE INSTRUCTIONS. TAKE TIME TO BE CAREFUL!
WARNING: BEFORE ATTEMPTING TO OPERATE THIS FORAGE BOX, READ AND STUDY THE FOL-
LOWING SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES
OR WORKS WITH THE FORAGE BOX, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH
THESE SAFETY PRECAUTIONS.
Require anyone who will operate this forage box to read and completely understand this owner’s manual. Give neces-
sary instructions.
DO NOT operate, service, inspect or otherwise handle this forage box until all operators have read this Owner’s Man-
ual and have been properly trained in its intended usage.
DO NOT allow minors (children) or inexperienced persons to operate this forage box.
DO NOT clean, adjust or lubricate while the forage box is in motion.
Inspect when first delivered and regularly thereafter; that all connections and bolts are tight and secure before operat-
ing.
Know how to stop operation of the forage box before starting it!
DO NOT operate until all shields and guards are in place and securely fastened.
Make certain everyone is clear of the forage box before applying power.
Keep hands, feet and clothing away from moving parts. Loose or floppy clothing should not be worn by the operator.
Observe all applicable traffic laws when transporting on public roadways (where legal to do so). Check local laws for
all highway lighting and marking requirements.
Tractor Models: Always install a SMV emblem on forage box for transporting on roadways and keep this emblem
clean and bright.
DO NOT step up on any part of the forage box at any time.
Keep the forage box away from power lines. Contact with electric lines may result in serious injury or death by electro-
cution!
If the forage box becomes clogged, shut off the power, set park brake, remove keys, keep keys in your possession,
and allow all mechanism to stop. Then, clean or work on the forage box as required.
Always shut off the power, remove keys, keep keys in your possession to prevent accidental startup or unexpected
movement before working on forage box.
Tractor Models: DO NOT tow at speeds in excess of 20 MPH when transporting this forage box. Never exceed a safe
travel speed.
MEYER MFG. CORP. PROVIDES GUARDS FOR EXPOSED MOVING PARTS FOR THE OPERATOR’S PROTECTION; HOW-
EVER, SOME AREAS CANNOT BE GUARDED OR SHIELDED IN ORDER TO ASSURE PROPER OPERATION. THE OPERA-
TOR’S MANUAL AND DECALS ON THE FORAGE BOX ITSELF WARN YOU OF DANGERS AND MUST BE READ AND
OBSERVED CLOSELY!
Study the Above Safety Rules
FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
--4--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
SAFETY FIRST
D
E
A
F
C
B
G
E
CAUTION: READ ALL DECALS ON THE FORAGE BOX AND IN THIS MANUAL. KEEP THESE DECALS CLEAN AND
REPLACE ANY LOST OR DESTROYED DECALS. BECOME FAMILIAR WITH ALL TRUCK OR TRACTOR AND FORAGE BOX
CONTROLS.
9100 Rear Unload
--5--
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
The Meyer Forage Box is manufactured with operator safety in mind. Located on the forage box are various decals to
aid in operation and warn of danger or caution areas. Pay close attention to all decals on the forage box.
DO NOT REMOVE ANY DECALS. IF DECALS ARE LOST, DAMAGED OR IF FORAGE
BOX IS REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTEC-
TION AND INFORMATION.
A brief definition of signal words that are used in this manual is as follows:
DANGER Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.
WARNING Indicates a potentially hazardous situation that, if not avoided could result in death or serious injury,
and includes hazards that are exposed when guards are removed.
CAUTION Indicates a potentially hazardous situation that, if not avoided may result in minor or moderate injury.
DECAL C.
PART NO. 46-0001-20
DECAL B.
PART NO. 46-0011-D
DECAL E.
DECAL D.
PART NO. 46-0001-4
PART NO. 46-0001-35
DECAL F.
PART NO. 46-0001-62
DECAL G.
PART NO.
46-0001-33
DECAL A.
PART NO. 46-0001-22
CAUTION: READ ALL DECALS ON THE FORAGE BOX AND IN THIS MANUAL. KEEP THESE DECALS CLEAN
AND REPLACE ANY LOST OR DESTROYED DECALS. BECOME FAMILIAR WITH ALL TRUCK OR TRACTOR AND FOR-
AGE BOX CONTROLS.
--6--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
PRE-OPERATION
GENERAL
Depending on make and model of truck, it may be neces-
sary to install a light converter. (Meyer part #56-0028).
Converter allows signal lights and brake lights to operate
according to DOT lighting.
Whenever adjusting, cleaning, lubricating or otherwise
servicing this forage box, you must shutoff and lockout
power to the box. Because this box can be truck
mounted or powered by a tractor, methods vary. On
truck mounted units, the connection between the PTO
and box is permanently installed and not intended to be
disconnected. On trucks, disengage the PTO drive, turn
off the engine, set the parking brake, remove the ignition
keys and keep them in your possession to prevent any-
one else from accidentally applying power to the box un-
expectedly. For tractors, disengage the hydraulics, turn
off the engine, set the brakes.
AIR BRAKE HOOKUP
Connect the control line (blue) from your truck air supply to
the blue gladhand on the trailer. Connect the tank supply
line (red) to the red gladhand on the trailer. See figure 1.
WARNING: IF THE ABS INDICATOR LAMP CO-
MES ON AND STAYS ON WHEN YOU APPLY
BRAKES TO A MOVING TRAILER, THE TRAILER
ABS IS NOT WORKING PROPERLY. THE ABS MUST
BE SERVICED AS SOON AS POSSIBLE UPON COM-
PLETION OF YOUR TRIP TO ENSURE FULL
ANIT-LOCK BRAKING CAPABILITY
Throughout this manual, when directed to shutoff and
lockout power, be familiar with the previously described
procedures for the type of machine you are operating.
Be sure your forage box is properly mounted to the truck
frame or to the wagon running gear. Consult your dealer
if you have any questions about proper installation. A tie
down kit from the manufacturer and illustrated in the
parts listing of this manual is available for wagon applica-
tions.
HYDRAULIC HOOKUP
Connect hydraulic lines from the hydraulic power supply
to the pressure and return lines as illutrated on figure 1.
Hydraulic input to the 9100 forage box requires 35GPM
@ 3000 PSI. If truck mounted, install a relief valve set at
3000 PSI. Engine RPM should be 1500 RPM. Set up hy-
draulic system on truck mounted units with a 40 gallon
reservoir minimum. Call factory for further information.
START UP AND STOPPING
Operation of the forage box with truck begins when the
PTO is engaged to run the hydraulic pump.
Operation for tractor pulled forage boxes begins when
the tractor hydraulic system is engaged.
WARNING: INSPECT REGULARLY THAT ALL
CONNECTIONS AND BOLTS ARE TIGHT AND SE-
CURE BEFORE OPERATING. FAILURE TO HEED MAY
RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
ABS INDICATOR
LAMP
BLUE GLADHAND
RED GLADHAND
Inspect the forage box for proper adjustments as this will
ensure maximum machine performance. See “Adjust-
ments” section. Grease and oil the forage box as re-
quired. See “Lubrication” section.
WARNING: DO NOT OPERATE UNTIL ALL
SHIELDS AND GUARDS ARE IN PLACE AND SE-
CURELY FASTENED. FAILURE TO HEED MAY RE-
SULT IN SERIOUS PERSONAL INJURY OR DEATH.
HYDRAULIC
PRESSURE
LINE
LIGHT HOOKUP
A 7 pin electrical socket is provided to plug the electrical
control plug from your truck or tractor. See figure 1
7 PIN ELECTRICAL SOCKET
HYDRAULIC RETURN LINE
This will operate signal, tail, clearance and brake lights.
FIGURE 1. ELECTRICAL LIGHT AND AIR BRAKE
HOOKUP
9100 Rear Unload
--7--
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSPORTING
WARNING: (TRACTOR POWERED) INSTALL
WARNING: MAKE CERTAIN EVERYONE IS
CLEAR OF EQUIPMENT BEFORE APPLYING
POWER. FAILURE TO HEED MAY RESULT IN SERI-
OUS PERSONAL INJURY OR DEATH.
A SMV EMBLEM ON REAR OF FORAGE BOX FOR
TRANSPORTING ON ROADWAYS. KEEP THIS EM-
BLEM CLEAN AND BRIGHT. FAILURE TO HEED
MAY RESULT IN SERIOUS PERSONAL INJURY OR
DEATH.
WARNING: (TRACTOR POWERED) DO NOT
TOW AT SPEEDS IN EXCESS OF 20 MPH. FAILURE
TO HEED MAY RESULT IN SERIOUS PERSONAL IN-
JURY OR DEATH.
Be sure and observe that the rear discharge door is
latched closed before traveling on roadways.
If you will travel on public roads you must know all rules
governing such operation. This will include lighting and
brake requirements in addition to traffic rules. You may
also be required to install a safety chain device on the
running gear.
WARNING: YOU MUST OBSERVE ALL AP-
PLICABLE TRAFFIC LAWS WHEN TRANSPORTING
ON PUBLIC ROADWAYS. CHECK LOCAL LAWS
FOR ALL HIGHWAY LIGHTING AND MARKING RE-
QUIREMENTS. FAILURE TO HEED MAY RESULT IN
SERIOUS PERSONAL INJURY OR DEATH.
TRACTOR TOWING SIZE
REQUIREMENTS
Operating speed is dictated by the terrain over which you
are traveling. Always use caution. Avoid traveling on
slopes or hills that are unsafe.
Use the following chart for calculating the minimum trac-
tor weight.
CAUTION: FOR TRACTOR TOWED USE
FLASHING WARNING LIGHTS WHEN TRANS-
PORTING ON ALL PUBLIC ROADWAYS, EXCEPT
WHEN PROHIBITED BY LAW.CHECK FOR TRAFFIC
CONSTANTLY. BE SURE YOU CAN SEE THAT NO
ONE IS ATTEMPTING TO PASS YOU AND THAT ALL
TRAFFIC IS SUFFICIENTLY CLEAR FROM YOU BE-
FORE MAKING ANY TURNS.
MODEL FORAGE BOX EMPTY MINIMUM
WEIGHT + LOAD = GW TRACTOR
WEIGHT UP
TO 20 MPH
9122
9124
6,300 + _____ = _____ 2/3 of box
gross weight
6,600 + _____ = _____ 2/3 of box
gross weight
MATERIAL ESTIMATED WEIGHT
PER CUBIC FOOT
MATERIAL
LBS / CU. FT.
47 LBS.
SOYBEANS
COTTON SEED DRY
CORN (SHELLED)
CORN SILAGE
HAYLAGE
20 LBS.
45 LBS.
30 LBS.
20 LBS.
SAWDUST
17 LBS.
SOURCE: ASAE
NOTE: HEAPED LOADS HAVE SIGNIFICANTLY
HIGHER CAPACITIES
--8--
Download from Www.Somanuals.com. All Manuals Search And Download.
8100 Rear Unload
REAR UNLOAD OPERATION
Whenever adjusting, cleaning, lubricating or otherwise
Unloading is best observed from the operator’s seat.
Keep moving the forage box forward to prevent silage
from being carried underneath into the main apron chain
return area.
servicing this forage box, you must shutoff and lockout
power to the box. Because this box can be truck
mounted or powered by a tractor, methods vary. On
truck mounted units, the connection between the PTO
and box is permanently installed and not intended to be
disconnected. On trucks, disengage the PTO drive, turn
off the engine, set the parking brake, remove the ignition
keys and keep them in your possession to prevent any-
one else from accidentally applying power to the box un-
expectedly. For tractors, disengage the hydraulics, turn
off the engine and set the brakes.
The front of the box has a plexiglass window for conve-
nient observation.
Throughout this manual, when directed to shutoff and
lockout power, be familiar with the previously described
procedures for the type of machine you are operating.
WARNING: MAKE CERTAIN EVERYONE IS
WELL CLEAR OF EQUIPMENT BEFORE APPLYING
POWER. FAILURE TO HEED MAY RESULT IN SERI-
OUS PERSONAL INJURY OR DEATH.
Tractor Pulled:
Always park the forage box and unloading tractor in a
straight line. Shift the unloading tractor to “Neutral” or
“Park”. Set the brakes and turn power off.
REAR
DISCHARGE
DOOR
Make sure all persons are well clear of the forage box
and the unloading area.
HINGE BOLTS
The rear discharge door opens automatically by releas-
ing its latches as the main aprons begin to move. The
rear discharge door can spring open with extreme force
when its latches release. See figure 1. Pressure of for-
age against the rear door causes it to spring open very
quickly.
WARNING: THE REAR DISCHARGE DOOR
CAN SPRING OPEN QUICKLY AND WITH EXTREME
FORCE. KEEP ALL PERSONS WELL CLEAR OF THE
FORAGE BOX AND UNLOADING AREA. FAILURE
TO HEED MAY RESULT IN SERIOUS PERSONAL IN-
JURY OR DEATH.
REAR DOOR
LATCHES
From the operator’s seat, restart, and SLOWLY engage
the apron chains to open the rear door. Once the door
opens, regulate the discharge flow with the engine
speed. Do not operate above rated engine speed.
FIGURE 2. REAR OPENING DISCHARGE DOOR
CAUTION - QUICK RELEASE
9100 Rear Unload
--9--
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: DO NOT STEP UP ON ANY PART OF THE FORAGE BOX AT ANY TIME. FAILURE TO HEED
MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
The unloading process described is to be performed by the operator alone. This will eliminate unexpected “start-ups”
and minimize other hazards that could result by more than one person in control. If the forage box should become
clogged, shut off all power to the forage box and wait for all motion to stop. Shut off and lockout power. Then clean out
the machine.
When finished unloading reduce engine speed to idle and disengage the truck PTO drive or the tractor hydraulics. Pull
the rear unload box straight ahead to pull the door away from the unloaded pile of forage. When free, gravity will allow
the door to swing shut and the door latches will engage the apron chain links to secure it shut. Observe that this hap-
pens properly.
WARNING: SHUT OFF AND LOCK OUT POWER BEFORE CLEANING, ADJUSTING, LUBRICATING OR
SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Allow box to completely clean out the last load of forage. It is recommended to lube the rear unload box before storage
to exclude moisture from bearings. Apply oil to roller chain drives with gravity oil luber and to the apron chains with a
brush. This is also a good time to inspect all adjustments and check for parts that need repair or replacement. Per-
forming these tasks now will guarantee that the box is ready for use at the beginning of the next season.
Never use “live” power to aid in the clean-out of a clogged machine. If any mechanism fails, move the forage box to a
safe work area and then repair the mechanism before proceeding with unloading of the forage. If repairs require re-
moval of forage from inside the forage box, remove the rear discharge door (bolted hinges on top of each side) and
empty the forage manually by hand through the rear opening.
DANGER: NEVER ENTER THE FORAGE BOX FOR ANY REASON WITHOUT FIRST SHUTTING OFF
AND LOCKING OUT POWER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Never enter the forage box for any reason if there is any possibility of power being applied to the unit.
--10--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
BOTH SIDES
LUBRICATION DIAGRAM
9100 Rear Unload
--11--
Download from Www.Somanuals.com. All Manuals Search And Download.
LUBRICATION
WARNING: SHUT OFF AND LOCK OUT
POWER BEFORE CLEANING, ADJUSTING, LUBRI-
CATING OR SERVICING THIS MACHINE. FAILURE
TO HEED MAY RESULT IN SERIOUS PERSONAL IN-
JURY OR DEATH.
DAILY LUBRICATION
(every 8-10 loads)
Oil (3) roller chains on apron drive. This is done by
opening the ball valve on the gravity oiler while
unloading, once per day.
WARNING: DO NOT STAND BEHIND UNIT
WHILE PERFORMING THIS OPERATION.
Refill the gravity oiler at the beginning of each day.
Grease three jackshaft bearings on the rear
driveshaft (each end, one @ center).
Oil (4) rear gate latch pivot bolts.
Grease (3) main apron shaft bearings.
END OF CROP CLEANUP AND
MAINTENANCE
Allow box to completely clean out last load of forage.
Clean out all forage material from inside the box and on
the outside of the box.
It is recommended to lube the forage box before storage
to exclude moisture from bearings. Apply oil to roller
chain drives with the gravity oil luber and to the main
apron chains with a brush.
It is also a good time to inspect all adjustments and check
for parts that need repair or replacement. Performing
these tasks now will guarantee that the forage box is
ready for use at the beginning of the next season.
--12--
Download from Www.Somanuals.com. All Manuals Search And Download.
8100 Rear Unload
ADJUSTMENTS
WARNING: SHUT OFF AND LOCK OUT POWER BEFORE CLEANING, ADJUSTING, LUBRICATING OR
SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Correct tension on the apron chains is when the apron chain slat is 1/8” to 1/4” off the return slides (three feet
from the front of the box). To tighten chains, tighten the adjuster bolts at each end of the front sprocket shafts. Each
apron chain has its own sprocket shaft. Tighten the adjuster bolts at each end of the shaft equally.
The roller chain drives are tensioned by automatic spring loaded tension blocks. Periodically tighteners will need to be
adjusted to maintain proper spring tension. Springs should be compressed to obtain approximately 5” overall length.
Front Shields Removed To Illustrate Service Components.
Do Not Remove This Shield To Perform The Service.
BOTH SIDES
ADJUSTMENT DIAGRAM
9100 Rear Unload
--13--
Download from Www.Somanuals.com. All Manuals Search And Download.
GEARBOX & CHAIN DRIVE
KEY PART NO.
DESCRIPTION
1
55-0122
Hydraulic Motor
2
25-8202
Motor Bracket
3
14-0044
2" Pillow Block Bearing
4
10-0091
Sprocket, 120B30, 2” Bore, ½” Key
Sprocket, 120B9, 1-1/2” Bore, ½” Key
#120-50 Roller Chain
5
10-0090
6
11-0133
7
805-0063-Z
851-6311-2.5Z
25-8207
Washer, 5/8” Flat
8
Bolt, 5/8-11 x 2-1/2 Hex Head Machine Bolt
Chain Tightener Spring Sleeve Weldment
Apron/Tightener Holder Assembly
Center #120 Tightener Arm Less Roller
3/4-10 Nylon Insert Locknut
3/4-10 x 3" M.B.
9
10
11
12
13
14
15
16
16A
16B
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
25-8209
25-8206-1
815-7510-Z
851-7510-3Z
25-8204
Chain Tightener Adjuster Rod
5/16 x 1-3/4" Roll Pin
38-0013
912-0016
912-0016-1
912-0016-2
23-0102-1
35-0024
7/8” Nylon Roller Complete
Nylon Roller Only
Inner Sleeve
Jackshaft, 2” x 96”
Key, ½” x ½” x 2 1/2” (1045 Mat)
Tightener Arm Assembly, Less Roller
Compression Tightener Spring
Spindle Washer Punchout
Sprocket, 120B9, 2" Bore, 1/2" Key
#120-46 Roller Chain
25-8205-1
29-0009
75-0453
10-0085
11-0132
35-0009
3/8 x 3/8 x 2-1/4" Key (1045 Material)
5/8-11 Spin Locknut
810-6311-Z
805-0075-Z
30-0010
Bolt Guide Sleeve Plate
1/8" NPT Zerk
25-8208
Tightener Pivot Shaft
25-8210
Center Tightener Pivot Shaft
Bolt, 3/8-16 x 1” Hex Head Machine Bolt
3/8” Internal Tooth Lockwasher
Bolt, 1/2-13 x 2” Hex Head Machine Bolt
1/2-13 Spin Locknut
851-3816-1Z
806-0038-Z
851-5013-2Z
810-5013-Z
--16--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
KEY PART NO.
DESCRIPTION
1
2
3
4
5
55-0122
9100 Hydraulic Motor
55-0130
#59-16-12 Female Swivel Fitting
3/4" Check Valve
55-0007-B
55-0027
3/4 x 90 Degree Elbow
55-0138
3/4" Hydraulic Pipe x 233" (9122)
3/4" Hydraulic Pipe x 252" (9124/26/28/30/36)
3/4" Black Steel Tee Fitting
55-0124
6
55-0079
7
55-0081
3/4" Steel Plug
8
851-3816-2Z
815-3816-Z
851-5013-2Z
55-0129
3/8-16 x 2" M.B. Zinc
9
3/8-16 Nylon Insert Locknut
1/2-13 x 2" M.B. Zinc
10
11
12
90 Degree Swivel Fitting
55-0136
3/4" Hydraulic Extension Pipes x 6" (9124)
3/4" Hydraulic Extension Pipes x 22" (9126)
3/4" Hydraulic Extension Pipes x 54" (9128)
3/4" Hydraulic Extension Pipes x 70" (9130)
3/4" Hydraulic Extension Pipes x 150" (9136)
3/4" Hydraulic Pipe x 226" (9122)
3/4" Hydraulic Pipe x 249" (9124/26/28/30/36)
3/4 x 90 Degree Street Elbow
Hydraulic Pipe Clamp
55-0135
55-0134
55-0133
55-0125
13
55-0137
55-0126
14
15
16
17
55-0082
100-8025-62
55-0029
3/4" Hydraulic Hose x 36" Long
3/4" Black Steel Coupler
55-0030
--18--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
APRON
KEY
PART NO.
23-0103-2
23-0103-1
701-.75-1.75-16
701-.75-1.75-18
701-.75-1.75-20
24-8206
DESCRIPTION
1
2
3
Outer Sprocket Spacer
Inner Sprocket Spacer
Chain Return Slide Rail (As Required)
Chain Return Slide Rail (As Required)
Chain Return Slide Rail (As Required)
9100 Front Apron Chain Shield
4
5
6
25-8201
Apron Chain Tightener Bolt
10-0092-1
13-0020
Idler Sprocket w/Bushing
Bushing, 1-3/4" ID x 2" OD x 1-1/2" Long
Tightener Block Weldment
7
25-8200
8
851-3816-1Z
23-0103-1
11-0107
3/8-16 x 1" M.B. Zinc
9
Idler Shaft
10
Main Apron Assy. (22 Ft.) 667XH (Prior to Serial # 0891238)
Main Apron Assy. (22 Ft.) 667K (Serial # 0891238 & Later)
Main Apron Assy. (24 Ft.) 667XH (Prior to Serial # 0891238)
Main Apron Assy. (24 Ft.) 667K (Serial # 0891238& Later)
Main Apron Assy. (26 Ft.) 667XH (Prior to Serial # 0891238)
Main Apron Assy. (26 Ft.) 667K (Serial # 0891238& Later)
Main Apron Assy. (28 Ft.) 667XH (Prior to Serial # 0891238)
Main Apron Assy. (28 Ft.) 667K (Serial # 0891238 & Later)
Main Apron Assy. (30 Ft.) 667XH (Prior to Serial # 0891238)
Main Apron Assy. (30 Ft.) 667K (Serial # 0891238 & Later)
Main Apron Assy. (36 Ft.) 667XH (Prior to Serial # 0891238)
Main Apron Assy. (36 Ft.) 667K (Serial # 0891238 & Later)
Main Apron Assy. (40 Ft.) 667XH (Prior to Serial # 0891238)
Main Apron Assy. (40 Ft.) 667K (Serial # 0891238 & Later)
Pintle Chain Link-D667XH (Prior to Serial # 0891238)
Pintel Chain Link-D667K (Serial # 0891238 & Later)
Rivet, 7/16 x 1"
11-0107-K
11-0125
11-0125-K
11-0134
11-0134-K
11-0135
11-0135-K
11-0136
11-0136-K
11-0137
11-0137-K
11-0142
11-0142-K
11-0107-2
11-0160-1-2
11-0107-6
11-0107-5
11-0107-3
11-0160-1-1
810-5013-Z
14-0041
11
12
13
14
Slat
Attachment Link-D667XH (Prior to Serial # 0891238)
D667K Attachement Link (Serial # 0891238 & Later)
1/2-20 Spin Locknut
15
16
17
18
19
20
21
RH/LH Main Drive Shaft Bearing Assembly
1/8" NPT Straight Zerk
30-0002
23-0101
9100 Main Drive Shaft Assembly
851-5013-1.25Z
30-0009
1/2-13 x 1-1/4" M.B. Zinc
Coupler 1/8" NPT x 3/4" Long
11-0107-1
11-0107-1-K
30-0006
667XH Slat w/Attachment Links (Prior to Serial # 0891238)
667K Slat w/Attachment Links (Serial # 0891238 & Later)
1/8" NPT x 90 Degree Zerk
22
23
24
25
26
25-8000-1
810-3816-Z
30-0016
Front Gate Center Support
3/8-16 Spin Locknut
1/8" NPT Close Nipple
14-0051
Split Center Bearing (Replacement)
--20--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
9100 MAIN BODY (1 OF 2)
KEY PART NO.
DESCRIPTION
1
100-8031
9122 Main Frame & Side Assembly
100-8030
9124 Main Frame & Side Assembly
100-8029
9126 Main Frame & Side Assembly
100-8027
9128 Main Frame & Side Assembly
100-8028
9130 Truck Main Frame & Side Assembly
9130 Trailer Main Frame & Side Assembly
9136 Trailer Main Frame & Side Assembly
Plexiglas Viewing Window
100-8026
100-8025
2
3
4
5
49-0089
100-8050-2
33-0045
Front Gate Stainless Steel Panel
Viewing Window Weather-strip (By the Foot)
9100 Stainless Steel Front Gate Complete
9100 Front Gate Welded Assembly
100-8050
100-8050-1
851-5013-1.5Z
810-5013-Z
49-0093
6
7
8
9
1/2-13 x 1-1/2" Machine Bolt Zinc
1/2-13 Spin Locknut
Main Roller Belting Seal 1/8 x 5 x 12"
25-8027-1
25-8028-1
709-48-254.5
709-48-286.5
709-48-302.5
709-48-334.5
709-48-350.5
709-48-430.5
100-8042-1
100-8042-2
100-8043-1
100-8057-1
25-8050
Center Floor Chain Guide 96"-Front / Middle
Center Floor Chain Guide 48"-Front / Middle
9122 Superslick Floor Panel 48 x 254-1/2"
9124 Superslick Floor Panel 48 x 286-1/2"
9126 Superslick Floor Panel 48 x 302-1/2"
9128 Superslick Floor Panel 48 x 334-1/2"
9130 Superslick Floor Panel 48 x 350-1/2"
9136 Superslick Floor Panel 48 x 430-1/2"
Stainless Steel Side Panel 72 x 120" (9122/24/28/30/36)
Stainless Steel Side Panel 72 x 144" (9122/26/28/30)
Stainless Steel Side Panel 72 x 65" (9124)
Stainless Steel Side Panel 72 x 96" (9126/36)
Front Screen Extension (All 9100's)(Optional Bolt In) (Not Shown)
Front Solid Extension (All 9100's)(Optional Bolt In) (Not Shown)
261-1/2" Left Screen Extension (9122/24)
261-1/2" Left Solid Extension (9122/24)
219-1/2" Left Rear Extension (9136)
10
11
NS
NS
12
25-8050-S
25-8051
25-8051-S
25-8250
25-8250-S
25-8254
219-1/2" Left Rear Solid Extension (9136)
139-1/2" Left Rear Screen Extension (9130)
139-1/2" Left Rear Solid Extension (9130)
123-1/2" Left Rear Screen Extension (9128)
123-1/2" Left Rear Solid Extension (9128)
91-1/2" Left Rear Screen Extension (9126)
91-1/2" Left Rear Solid Extension (9126)
25-8254-S
25-8256
25-8256-S
25-8258
25-8258-S
--22--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
9100 MAIN BODY (2 OF 2)
8100 Rear Unload
--23--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 MAIN BODY (2 OF 2)
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
13
25-8052
261-1/2" Right Screen Extension (9122/24) (Not Shown)
261-1/2" Right Solid Extension (9122/24) (Not Shown)
32" Left/Right Screen Extension (Not Shown)
32" Left/Right Solid Extension (Not Shown)
218-1/2" Right Front Screen Extension (9126/28/30/36) (Not Shown)
218-1/2" Right Front Solid Extension (9126/28/30/36) (Not Shown)
219-1/2" Right Rear Screen Extension (9136) (Not Shown)
219-1/2" Right Rear Solid Extension (9136) (Not Shown)
139-1/2" Right Rear Screen Extension (9130) (Not Shown)
139-1/2" Right Rear Solid Extension (9130) (Not Shown)
123-1/2" Right Rear Screen Extension (9128) (Not Shown)
123-1/2" Right Rear Solid Extension (9128) (Not Shown)
91-1/2" Right Rear Screen Extension (9126) (Not Shown)
91-1/2" Right Rear Solid Extension (9126) (Not Shown)
1/4-20 x 3/4" M.B. Zinc
25-8052-S
25-8053
25-8053-S
25-8253
25-8253-S
25-8251
25-8251-S
25-8255
25-8255-S
25-8257
25-8257-S
25-8259
25-8259-S
851-2520-.75Z
815-2520-Z
25-8252
14
1/4-20 Nylon Insert Locknut
15
218-1/2" Left Front Screen Extension (9126/28/30/36)
218-1/2" Left Front Solid Extension (9126/28/30/36)
Right Hand Lower 120 Chain Shield
25-8252-S
24-8202
16
17
18
19
20
21
22
NS
NS
23
NS
24
25
25-8008
Fender (Optional on Truck Mount Models)
9100 Front Gate Belting
49-0090
24-8204-3
24-8205-3
24-8203
Right Hand Upper 120 Chain Shield w/ Belting
Left Hand Upper 120 Chain Shield w/ Belting
Left Hand Lower 120 Chain Shield
25-8220-1
25-8220-2
25-8220-3
25-8024-1
25-8021-1
25-8203-1
24-8201-1
24-8209-1
49-0100
9100 Right/Left Side Chain Guide 120"
Front Right Floor Cap End Cap (Not Shown)
Front Left Floor Cap End Cap (Not Shown)
Rear Center Floor Chain Guide 96"
Center V End Cap (Not Shown)
Front Floor Cover
Rear Lower Frame Cover (Trailer Mount Only)(Prior to Ser.#0591210)
Rear Lower Frame Cover (Trailer Mount Only)(Ser.#0591210 & Later)
Meyer Mud Flap 9100
26
27
28
29
30
25-8212
Mud Flap Attaching Strap
851-3816-1.25Z
805-0038-Z
815-3816-Z
3/8-16 x 1-1/4" M.B. Zinc
3/8" Washer
3/8-16 Nylon Insert Locknut
NOTE: All extensions are available in either screen or solid panel. Front extension
--24--
Download from Www.Somanuals.com. All Manuals Search And Download.
8100 Rear Unload
FRONT AIR HOOK-UP &
FRONT FOLD DOWN EXTENSION
KEY PART NO.
DESCRIPTION
1
25-8059-S
25-8059
Solid Fold Down Front Extension
Fold Down Front Screen Extension-Optional
Hinge Mount Tab
2
100-8016
25-8081
3
Linkage Pipe Assembly
Handle Welded Assembly
Handle Pivot Bracket
4
25-8082
5
100-8014
16-0027
6
Swivel Eyelet
7
813-5020-Z
100-8020-64
51-0003
1/2-20 Fine Threaded Nut Zinc
Gate Stop Sleeve
8
9
Rubber Grip
10
11
12
13
14
100-9000-2
100-9000-3
100-8025-47
55-0170
Emergency Glad Hand-Red
Service Glad Hand-Blue
Front Receptacle Bracket
3/8" MPT x 3/8" Tube Connector
3/8" MPT x 1/2" Tube Connector
55-0171
--26--
Download from Www.Somanuals.com. All Manuals Search And Download.
8100 Rear Unload
REAR DOOR
9100 Rear Unload
--27--
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR DOOR
KEY PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
851-5013-2.5Z
1/2-13 x 2.5 Hex Head Machine Bolt
1/2" SAE Flat Washer
828-0050-Z
100-8012-7
814-5013-Z
851-2520-.75Z
49-0086
Backgate Latch
1/2-13 Center Locknut
1/4-20 x 3/4" M.B. Zinc
Backgate Belting
25-8005-1
25-8005-2
100-8055
Belting Attaching Strip, Right Hand
Belting Attaching Strip, Left Hand
Backgate Assembly Complete, (Standard Height Gate 82-1/2")
Backgate Assembly Complete, (High Back Gate 94-1/2")
Backgate Welded Assembly, (Standard Height Gate 82-1/2")
Backgate Welded Assembly, (High Back Gate 94-1/2")
Standard Rear Gate Stainless Panel 48 x 80"
High Rear Gate Stainless Panel 48 x 92"
1/2-13 Spin Locknut
100-8056
9A
10
100-8015-1
100-8017-1
100-8055-2
100-8056-1
810-5013-Z
851-5013-1.5Z
100-8012-15
100-8013-6
815-5013-Z
810-2520-Z
100-8062
11
12
13
14
15
16
17
1/2-13 x 1.5 Hex Head Machine Bolt
Backgate Hinge Weldment
Gate Stop
1/2-13 Nylon Locknut
1/4-20 Spin Locknut
Right Pivot Extension Assembly (High Gate Only-Truck Mt.)
Trailer R. Pivot Ext (Std Gate)
*100-8066
*100-8064
100-8063
Trailer R. Pivot Ext (High Gate)
18
19
Left Pivot Extension Assembly (High Gate Only-Truck Mt.)
Trailer L. Pivot Ext (Std Gate)
*100-8067
*100-8065
49-0088
Trailer L. Pivot Ext (High Gate)
Side Gate Belting Seal 66"
* Effective Serial No. 0591212 and later. Prior, see numbers 100-8062/100-8063 for high gate only.
--28--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
OPTIONAL DOUBLE DOOR
KEY PART NO.
DESCRIPTION
1
100-8109-1
100-8109
100-8110-1
100-8110
100-8102
100-8103
100-8104
100-8111
100-8106
100-8112
100-8108
24-8208
9100 Right Hand Door Welded Assembly
9100 Right Hand Door Complete
9100 Left Hand Door Welded Assembly
9100 Left Hand Door Complete
Double Door Gate Hinge Pin Weldment
Double Door Bottom Linkage Arm Weldment
Double Door Linkage Pipe Weldment
9100 Double Door Linkage Tie Rod Weldment
Double Door Linkage Clevis Weldment
9100 Double Door Linkage Pivot Shaft Weldment
Double Door Solenoid Mount Bracket
Double Door Left #120 Chain Shield
Double Door Air Chamber
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
55-0154
16-0027
Double Door 1/2" Swivel Eyelet
1-1/4" Bearing W/Lock Collar
14-0002-3
14-0003-1
14-0003-2
100-8100-6
24-8207
1-1/4" 2-Hole Pillow Block Flange
1-1/4" 2-Hole Plain Flange
Double Door Latch
Double Door Right #120 Chain Shield
Door Panel
100-8100-16
THE FOLLOWING ITEMS ARE NOT ILLUSTRATED
49-0033
55-0150
55-0151
55-0152
55-0153
55-0155
Double Door Back Gate Belting 5" x 42"
3/8" Air Line (25’ Required)
3/8" Hex Plug
3/8 x 3/8 x 90 Degree Elbow
3/8" x 1/8" Connector
12 Volt Solenoid Valve
--30--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
ROLLER CHAIN OILER
KEY PART NO.
DESCRIPTION
1
33-8001-1
33-8001
Oil Reservoir
9100 Oil Reservoir Complete w/Fittings
1/4 x 90 Degree Elbow
Ball Valve
2
30-0015
3
33-8000-6
33-8002-2
33-8000-5
33-8001-2
4
Brass Female Cross
5
90 Degree Brass Compression Fitting
Oiler Site Tube
6
7
952-0001-1-21 Tubing, 5/32" Nylon (By the Foot)
8
33-8001-4
1/8" NPT Nut
9
33-8000-10
Chain Brush Holder-Center
10
11
12
13
952-0001-1-25 Brush Assembly with 5/32" Insert & 1/2-20 Nut
33-8001-5
33-8000-11
08-0050
1/8" NPT Nipple
Chain Brush Holder-Outer
5/16" Loom Clamp
9100 Rear Unload
--31--
Download from Www.Somanuals.com. All Manuals Search And Download.
HIGHWAY TRANSPORT LIGHTS
KEY PART NO.
DESCRIPTION
#1232 4-Way Socket (4 Pin)
1
2
3
4
56-0004
56-0001-3
32-0026
56-0003
56-0032
Bezel Blank, Black
14” Nylon Tie Strap
Ag Light Harness w/Tri Plugs (Prior to Serial #06T91201)
Ag Light Harness w/Module (Serial #0691201 & Later) (Truck Mount Only)
56-0035
56-0022
Trailer Harness (9100 Trailers Only)
Truck Mount Dual Light RH w/Tri Plug (Prior to Serial #0691201)
Truck Mount Dual Light RH w/4-Prong (Serial #0691201 & Later)
Truck Mount Dual Light LH w/Tri Plug (Prior to Serial #0691201)
Truck Mount Dual Light LH w/4-Prong (Serial #0691201 & Later)
#1157 Bulb
5
6
56-0031-TR
56-0021
56-0030-TR
56-0001-4
32-0024
7
8
3/8” Plated Loom Clamp
Caution Tail Light Decal
9
46-0001-62
56-0001-2
56-0001-1
56-0028
10
11
12
13
13A
13B
14
15
Red Lens
Amber Lens
Tail Light Converter (Truck Models Only)
Amber 2-1/2" Round Marker Lamp LED
2-1/2" Round Rubber Grommet
56-0025-LED
56-0026
56-0027
2-Wire 6" Pigtail Wire Connector
Amber Marker Lamp LED
Red Marker Lamp LED
56-0023-LED
56-0024-LED
--32--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
OPTIONAL GRAIN KIT
KEY PART NO.
DESCRIPTION
22 851-5013-1.5Z ½-13 x 1-1/2" M.B. Zinc
1
2
3
4
5
25-8060
25-8061
124
Grain Kit Main Body
Grain Kit Gate Weldment
1" Pillow Block Bearing
1" Lock Collar
23 815-5013-Z
24 52-0005-3
½-13 Nylon Insert Locknut Zinc
18-1/2" Broom (Prior to Serial
#0791222)
52-0005-6-2
7-3/4" Left Inner Broom (Serial
#0791222 & Later)
323
10-0001
Sprocket 50B13, 1" Bore, 1/4"
Keyway
25 52-0005-5
25A 49-0088
Gate Seal Brush 64” Brush
Side Gate Belting Seal 66” (Se-
rial #0781239 & Later)
6
7
8
9
23-0099
Gate Shaft 1" x 32"
851-3816-2Z
15-0006-1
15-0006-2
15-0006
3/8-16 x 2" M.B. Zinc
Universal Knuckle
26 57-0009-2
27 33-0028
S-Hook
Handle Nut
Universal Sleeve Assembly
28 811-5013-4Z
29 25-8065
½ x4" Eyebolt (6" Overall)
Complete Universal
Knuckle/Sleeve Assy.
Seal Gasket (Prior to Serial
#0781239)
10 815-3816-Z
11 25-8062
12 25-8027
13 49-0089
3/8-16 Nylon Insert Locknut
Grain Kit Door Handle
Handle Lock Chain
25-8060-26
Lower Side Seal Filler Panel
(Serial #0781239 & Later)
30 25-8066
Main Roller Center Mount
Cover
Plexiglas Window 2-1/2" Ra-
dius
31 25-8060-21
32 49-0042
Rear Belting Seal Metal Strip
Rear Belting Seal
13A 33-0049
Window Weather-strip (By the
Foot) (Not Shown)
33 25-8060-27
Side Seal Filler Panel (Serial
#0791222 & Later)
14 49-0087
15 25-8078
Poly Bottom Panel
R.H. Gate Stop Weldment
Hi/Lo Gate (Prior to Serial
#0791222)
34 25-8060-23
35 56-0050
56-0050-1
Rear Light Mount Bracket
Light Harness and Lamp Kit
Center Lamp Bar Only
Left Rear Lamp Only
Harness Only
25-8178
16 25-8079
25-8179
R.H. Gate Stop Hi/Lo Gate (Se-
rial #0791222 & Later)
56-0050-2
L.H. Gate Stop Weldment Hi/Lo
Gate (Prior to Serial #0791222)
56-0050-3
56-0050-4
Right Rear Lamp Only
L.H. Gate Stop Hi/Lo Gate (Se-
rial #0791222 & Later)
36 56-0051
Light Harness Jumper-Y-Plug
Assy.
17 49-0036
18 49-0035
19 25-8067-1
20 52-0005-2
L.H. Chain Return Seal
R.H. Chain Return Seal
Chain Return Seal Mount Strap
24" Broom (Prior to Se-
rial#0791222)
52-0005-6-1
35-1/2" Broom Notched (Serial
#0791222 & Later)
21 100-8013-6
Rear Gate Stop
THE FOLLOWING ITEMS ARE NOT ILLUSTRATED
25-8211-1
55-0029
55-0047
55-0049
55-0076
55-0082
Flow Control Mount Bracket
3/4” Hose x 36” Long
3/4” Hose x 42” Long
3/4” Hose x 65” Long
Flow Control
3/4 x 90 Degree Street Elbow
--34--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
GATE DELAY PACKAGE (#8100 - GATE)
SN #0791233 & Later
KEY
1
PART NO.
25-8090-1
25-8105
25-8104
25-8093-1
24-8009
24-8010
55-0093
DESCRIPTION
QTY.
1
8100 GATE TOP CYLINDER BRACKET
SIDE MOUNT GRND CONT ROL ROD
SIDE MOUNT OIL RESEVOIR
2
1
3
1
4
8100 GATE LOWER SHAFT BRACKET
SIDE MT OIL RES 12" HOSE SHIELD 25-1/2"
SIDE MNT OIL RES HOSE SHIELD 13-1/2"
HYD CYLINDER 2" BORE 8" STROKE 18-1/4"
1
5
AR
AR
1
6
7
8
955-3802-10 CYLINDER PIVOT PIN WITH CLIP
1
9
952-0001-7
55-0094
55-0096
55-0193
55-0192
55-0194
55-0193
NYLON TIE STRAPS
1
10
11
12
FLOW CONTROL
1
3/8" NPTF 90* MALE PIPE ELBOW
1/4"x 52" LONG HOSE HI GATE W/EXT
1/4"x 40" LONG HOSE REG GATE NO/EXT
1/4"x 62-1/2"" LONG HOSE HI GATE W/EXT
1/4"x 52" LONG HOSE REG GATE NO/EXT
1
AR
AR
AR
AR
1
13
14
811-3816-3Z 3/8-16x3" EYEBOLT ZINC
25-8098
GATE TRIP CABLE ASSEMBLY W/EYEBOLT
1
15
16
17
18
19
20
21
22
23
24
25
810-3816-Z
36-0009
3/8 SPIN LOCK NUT
2
1/8" STAINLESS AIRCRAFT CABLE (BY THE FT)
3/16X2" COTTER PIN
2.41
1
823-19-2
25-8092-1
25-8106-1
55-0196
REAR GATE TOP SHAFT ASSY.
GROUND CONTROL ROD BRACKET
3/8Mx1/4" SWIVEL FEMALEx90 ELBOW
3/8 MALE-1/4FEMALE STREET ELBOW
1/4" MALE TO 1/4" FEMALE SWIVEL COUPLER
GATE RELEASE TRIP ARM ASSEMBLY
GATE LOWER SLEEVE SPACER
RUBBER GROMMET
1
1
1
55-0195
2
55-0191
1
25-8096
1
25-8097-1
33-1003
1
1
--36--
Download from Www.Somanuals.com. All Manuals Search And Download.
8100 Rear Unload
GATE DELAY PACKAGE
(#8100-Gate)
GATE DELAY ADJUSTMENTS
When the gate is completely closed (Tight to rear upright) cable and eyebolt assembly should be adjusted so cable has
no slack. Cable should be tight but not overtightened. If cable and eyebolt is overtightened lower cylinder will trip out of
the L-shaped slot on the lower bracket too soon and the gate will try to close before the cylinder is stroked out. If the ca-
ble and eyebolt is too loose the lower cylinder will not trip out of the L-shaped slot and the cylinder will reach its maxi-
mum stroke and the gate will still not be in the closed position. The gate will be held open by the top cylinder bracket
and the bracket may become damaged over time. Eyebolt and cable will need to be adjusted periodically to maintain
proper operation.
KEY PART NO. DESCRIPTION
KEY PART NO. DESCRIPTION
1
2
3
4
5
6
55-0095
30-0015
25-8095
55-0097
55-0094
55-0096
1/8" to 3/8" NPT Reducer
1/4x90 Degree Elbow
Oil Reservoir Assembly
3/8 to 3/8" Hydraulic Nipple
Flow Control Valve
11
952-0007- 7-1/4" Nylon Tie Strap
1
12
13
14
15
16
25-8098
Cable/Eyebolt Assy.
25-8097-1 Lower Sleeve Spacer
25-8093-1 Lower Shaft Plate Assy.
25-8095-6 Top Copper Line Assy.
3/8 NPT x 90 Degree Male Pipe
Elbow
25-8101
Ground Control Rod Assy.
W/Grip
7
25-8096
Gate Release Trip Arm Assembly
17
18
19
51-0007
Handle Grip
8
25-8092-1 Gate Regulator Top Shaft Assy.
25-8090-1 Top Cylinder Bracket Assy.
933-3804 5/16 x 4” Eyebolt
9
825-25-1Z 1/4x1" Self Tapping Screw
10
55-0093
Hydraulic Cylinder
8100 Rear Unload
--37--
Download from Www.Somanuals.com. All Manuals Search And Download.
“SPECIFICATIONS”
TRUCK MOUNT MODELS
TRAILER MODELS
9122
22'
9124
24'-8"
98"
9126
26'
9128
28'-8"
98"
9130
30'
9130T
30'
9136T
36'-8"
98"
DIMENSIONS
Inside Length
98"
98"
98"
98"
Inside Height
w/out ext.
72.5"
72.5"
72.5"
72.5"
72.5"
72.5"
72.5"
Inside Height
w/ext.
86.5"
86.5"
86.5"
86.5"
86.5"
86.5"
86.5"
Overall Length
Overall Width
22'-9"
102"
103"
25'-5"
102"
103"
26'-9"
102"
103"
29'-5"
102"
103"
30'-9"
102"
103"
30'-9"
102"
37'-5"
102"
Overall Height
w/out ext. (Top of
Gate)
145.5"
145.5"
Overall Height
w/ext. (Top of
Gate)
114"
114"
114"
114"
114"
159.5"
159.5"
Overall Side
Height-No
ext./ext.
90/104"
90/104"
90/104"
90/104"
90/104"
129.5/143. 129.5/143.
5"
5"
Stringer Width
(Truck Mount)
33.5"
1060
33.5"
1200
33.5"
1260
33.5"
1390
33.5"
1460
NA
1460
NA
1780
Capacity (Struck
Level) cu. Ft.
w/out ext.
Capacity (Struck
Level) cu. Ft.
w/ext.
1270
1400
1495
1640
1720
1720
2105
SPECIFICA-
TIONS
Maximum Net
Load
25 ton
25 ton
#120
25 ton
#120
25 ton
#120
25 ton
#120
30 ton
#120
30 ton
#120
Roller Chain Drive #120
on Each Side
Apron Chains
(Pintle)
667XH
667XH
667XH
667XH
667XH
667XH
667XH
Rear Drive
Shaft-Heavy Duty
2-1/2" Hvy 2-1/2" Hvy 2-1/2" Hvy 2-1/2" Hvy 2-1/2" Hvy 2-1/2" Hvy 2-1/2" Hvy
Upright Spacing
16" On
Center
Upright Construc- 2" x 2"
16" On
Center
16" On
Center
16" On
Center
16" On
Center
16" On
Center
16" On
Center
2" x 2"
Tubing
2" x 2"
Tubing
2" x 2"
Tubing
2" x 2"
Tubing
2" x 2"
Tubing
2" x 2"
Tubing
tion
Tubing
Power Source
Hydraulic
40 Sec.
Hydraulic
40 Sec.
Hydraulic
40 Sec.
Hydraulic
60 Sec.
Hydraulic
60 Sec.
Hydraulic
90 Sec.
Hydraulic
90 Sec.
Unloading Time
(Dependant on
Hydraulic System)
STANDARD
FEATURES
Stainless Steel
Sides-Front &
Back
STD.
STD.
STD.
STD.
STD.
STD.
STD.
Superslide Solid
Poly Floor
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
Gate Delay Sys-
tem
Automatic Roller
Chain Tighteners
--39--
Download from Www.Somanuals.com. All Manuals Search And Download.
9100 Rear Unload
“SPECIFICATIONS”
TRUCK MOUNT MODELS
TRAILER MODELS
Automatic Rear
Door Latching
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
STD.
Front Gate
Viewing Window
Semi-Automatic
Roller Chain Oiler
Rear Lights,
Marker Lights &
D.O.T. Tape
Personalized
Farm Name on
Sides
STD.
STD.
STD.
STD.
STD.
STD.
STD.
OPTIONS
14" Removable
Side Extensions
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
Double Center
Opening Doors
Grain Kit (Top
Pivot Door Only)
Truck Mount Kit
w/steel Fenders
Factory Installa-
tion of Truck
Mount Kit
TARP SYSTEMS
Front to Back
Scissors Tarp
(Electric)
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
OPT.
Side to Side Roll
Tarp (Electric)
Manufactured by:
Meyer Mfg. Corp.
County Hwy. A West
P.O. Box 405
Dorchester, Wisconsin 54425-0405
Phone 715-654-5132 · FAX 715-654-5513
1-800-325-9103
E-mail: sales @meyermfg.com
Farm Equipment Buyers Trust the Name Meyer!
--40--
Download from Www.Somanuals.com. All Manuals Search And Download.
8100 Rear Unload
This Page Intentionally Blank
8100 Rear Unload
--41--
Download from Www.Somanuals.com. All Manuals Search And Download.
This Page Intentionally Blank
--42--
Download from Www.Somanuals.com. All Manuals Search And Download.
8100 Rear Unload
A
Download from Www.Somanuals.com. All Manuals Search And Download.
|
